* MX6sabresd broken since v2019.04 @ 2021-02-01 10:59 Marek Vasut 2021-02-01 11:07 ` Fabio Estevam 0 siblings, 1 reply; 19+ messages in thread From: Marek Vasut @ 2021-02-01 10:59 UTC (permalink / raw) To: u-boot Hello everyone, the mx6sabresd is broken since 1ca12f034e ("configs: mx6sabresd: Add SPL FIT and DM support"), it hangs in SPL when booting from SD card, can you please take a look and fix it? I don't have the board myself, I just helped bisect it remotely just now. Thanks -- Best regards, Marek Vasut ^ permalink raw reply [flat|nested] 19+ messages in thread
* MX6sabresd broken since v2019.04 2021-02-01 10:59 MX6sabresd broken since v2019.04 Marek Vasut @ 2021-02-01 11:07 ` Fabio Estevam 2021-02-01 11:28 ` Marek Vasut 0 siblings, 1 reply; 19+ messages in thread From: Fabio Estevam @ 2021-02-01 11:07 UTC (permalink / raw) To: u-boot Hi Marek, On Mon, Feb 1, 2021 at 7:59 AM Marek Vasut <marex@denx.de> wrote: > > Hello everyone, > > the mx6sabresd is broken since 1ca12f034e ("configs: mx6sabresd: Add SPL > FIT and DM support"), it hangs in SPL when booting from SD card, can you > please take a look and fix it? I don't have the board myself, I just > helped bisect it remotely just now. The mx6sabresd boots fine on 2021.01. Could you please give it a try? ^ permalink raw reply [flat|nested] 19+ messages in thread
* MX6sabresd broken since v2019.04 2021-02-01 11:07 ` Fabio Estevam @ 2021-02-01 11:28 ` Marek Vasut 2021-02-01 11:37 ` Fabio Estevam 0 siblings, 1 reply; 19+ messages in thread From: Marek Vasut @ 2021-02-01 11:28 UTC (permalink / raw) To: u-boot On 2/1/21 12:07 PM, Fabio Estevam wrote: > Hi Marek, Hi, > On Mon, Feb 1, 2021 at 7:59 AM Marek Vasut <marex@denx.de> wrote: >> >> Hello everyone, >> >> the mx6sabresd is broken since 1ca12f034e ("configs: mx6sabresd: Add SPL >> FIT and DM support"), it hangs in SPL when booting from SD card, can you >> please take a look and fix it? I don't have the board myself, I just >> helped bisect it remotely just now. > > The mx6sabresd boots fine on 2021.01. Could you please give it a try? Did you test that yourself? I am CCing Christoph, as I don't have the board. The report I am getting is that it does not boot fine on his end when writing u-boot-with-spl.imx to SD card at offset 1024B. ^ permalink raw reply [flat|nested] 19+ messages in thread
* MX6sabresd broken since v2019.04 2021-02-01 11:28 ` Marek Vasut @ 2021-02-01 11:37 ` Fabio Estevam 2021-02-01 11:58 ` Marek Vasut 0 siblings, 1 reply; 19+ messages in thread From: Fabio Estevam @ 2021-02-01 11:37 UTC (permalink / raw) To: u-boot Hi Marek, On Mon, Feb 1, 2021 at 8:28 AM Marek Vasut <marex@denx.de> wrote: > Did you test that yourself? I am CCing Christoph, as I don't have the Yes, I tested it myself: U-Boot SPL 2021.01 (Jan 23 2021 - 14:34:35 -0300) Trying to boot from MMC1 U-Boot 2021.01 (Jan 23 2021 - 14:34:35 -0300) CPU: Freescale i.MX6Q rev1.2 996 MHz (running at 792 MHz) CPU: Automotive temperature grade (-40C to 125C) at 43C Reset cause: POR Model: Freescale i.MX6 Quad SABRE Smart Device Board I2C: ready DRAM: 1 GiB PMIC: PFUZE100 ID=0x10 MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 3 Loading Environment from MMC... OK No panel detected: default to Hannstar-XGA Display: Hannstar-XGA (1024x768) In: serial Out: serial Err: serial Net: eth0: ethernet at 2188000 Hit any key to stop autoboot: 0 > board. The report I am getting is that it does not boot fine on his end > when writing u-boot-with-spl.imx to SD card at offset 1024B. I have flashed the SD card by writing SPL at offset 1kB and u-boot-dtb.img at 69kB. ^ permalink raw reply [flat|nested] 19+ messages in thread
* MX6sabresd broken since v2019.04 2021-02-01 11:37 ` Fabio Estevam @ 2021-02-01 11:58 ` Marek Vasut 2021-02-01 12:13 ` Fabio Estevam 0 siblings, 1 reply; 19+ messages in thread From: Marek Vasut @ 2021-02-01 11:58 UTC (permalink / raw) To: u-boot On 2/1/21 12:37 PM, Fabio Estevam wrote: > Hi Marek, Hello Fabio, > On Mon, Feb 1, 2021 at 8:28 AM Marek Vasut <marex@denx.de> wrote: > >> Did you test that yourself? I am CCing Christoph, as I don't have the > > Yes, I tested it myself: > > U-Boot SPL 2021.01 (Jan 23 2021 - 14:34:35 -0300) > Trying to boot from MMC1 > > > U-Boot 2021.01 (Jan 23 2021 - 14:34:35 -0300) > > CPU: Freescale i.MX6Q rev1.2 996 MHz (running at 792 MHz) > CPU: Automotive temperature grade (-40C to 125C) at 43C > Reset cause: POR > Model: Freescale i.MX6 Quad SABRE Smart Device Board > I2C: ready > DRAM: 1 GiB > PMIC: PFUZE100 ID=0x10 > MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 3 > Loading Environment from MMC... OK > No panel detected: default to Hannstar-XGA > Display: Hannstar-XGA (1024x768) > In: serial > Out: serial > Err: serial > Net: eth0: ethernet at 2188000 > Hit any key to stop autoboot: 0 > >> board. The report I am getting is that it does not boot fine on his end >> when writing u-boot-with-spl.imx to SD card at offset 1024B. > > I have flashed the SD card by writing SPL at offset 1kB and > u-boot-dtb.img at 69kB. Then I have to wonder, does it also work if you write u-boot-with-spl.imx to the SD card ? If not, then that might be the problem . ^ permalink raw reply [flat|nested] 19+ messages in thread
* MX6sabresd broken since v2019.04 2021-02-01 11:58 ` Marek Vasut @ 2021-02-01 12:13 ` Fabio Estevam 2021-02-01 12:17 ` Marek Vasut 0 siblings, 1 reply; 19+ messages in thread From: Fabio Estevam @ 2021-02-01 12:13 UTC (permalink / raw) To: u-boot On Mon, Feb 1, 2021 at 8:58 AM Marek Vasut <marex@denx.de> wrote: > Then I have to wonder, does it also work if you write > u-boot-with-spl.imx to the SD card ? If not, then that might be the > problem . Yes, this is the problem. When flashing u-boot-with-spl.imx: U-Boot SPL 2021.01 (Feb 01 2021 - 09:10:08 -0300) Trying to boot from MMC1 mmc_load_image_raw_sector: mmc block read error SPL: failed to boot from all boot devices ### ERROR ### Please RESET the board ### ^ permalink raw reply [flat|nested] 19+ messages in thread
* MX6sabresd broken since v2019.04 2021-02-01 12:13 ` Fabio Estevam @ 2021-02-01 12:17 ` Marek Vasut 2021-02-01 12:22 ` Fabio Estevam 0 siblings, 1 reply; 19+ messages in thread From: Marek Vasut @ 2021-02-01 12:17 UTC (permalink / raw) To: u-boot On 2/1/21 1:13 PM, Fabio Estevam wrote: > On Mon, Feb 1, 2021 at 8:58 AM Marek Vasut <marex@denx.de> wrote: > >> Then I have to wonder, does it also work if you write >> u-boot-with-spl.imx to the SD card ? If not, then that might be the >> problem . > > Yes, this is the problem. When flashing u-boot-with-spl.imx: > > U-Boot SPL 2021.01 (Feb 01 2021 - 09:10:08 -0300) > Trying to boot from MMC1 > mmc_load_image_raw_sector: mmc block read error > SPL: failed to boot from all boot devices > ### ERROR ### Please RESET the board ### All right, now we are aligned, good. But that ^ should work, right? ^ permalink raw reply [flat|nested] 19+ messages in thread
* MX6sabresd broken since v2019.04 2021-02-01 12:17 ` Marek Vasut @ 2021-02-01 12:22 ` Fabio Estevam 2021-02-01 13:01 ` Marek Vasut 0 siblings, 1 reply; 19+ messages in thread From: Fabio Estevam @ 2021-02-01 12:22 UTC (permalink / raw) To: u-boot On Mon, Feb 1, 2021 at 9:17 AM Marek Vasut <marex@denx.de> wrote: > All right, now we are aligned, good. But that ^ should work, right? Yes, good that we narrowed it down to the u-boot-with-spl.imx format. Personally, I haven't used the u-boot-with-spl.imx format before, so I didn't notice it is broken (at least for mx6sabresd). ^ permalink raw reply [flat|nested] 19+ messages in thread
* MX6sabresd broken since v2019.04 2021-02-01 12:22 ` Fabio Estevam @ 2021-02-01 13:01 ` Marek Vasut 2021-02-01 13:09 ` Fabio Estevam 0 siblings, 1 reply; 19+ messages in thread From: Marek Vasut @ 2021-02-01 13:01 UTC (permalink / raw) To: u-boot On 2/1/21 1:22 PM, Fabio Estevam wrote: > On Mon, Feb 1, 2021 at 9:17 AM Marek Vasut <marex@denx.de> wrote: > >> All right, now we are aligned, good. But that ^ should work, right? > > Yes, good that we narrowed it down to the u-boot-with-spl.imx format. > > Personally, I haven't used the u-boot-with-spl.imx format before, so I > didn't notice it is broken (at least for mx6sabresd). Per arch/arm/mach-imx/Makefile , u-boot-with-spl.imx is a concatenation of SPL and u-boot.uim, which is different than u-boot-dtb.img . The .uim is plain uImage, the .img is fitImage . I suspect that's where the problem stems from. I think u-boot-with-spl.imx: SPL u-boot.uim FORCE should really be u-boot-with-spl.imx: SPL u-boot.img FORCE under certain (which ?) conditions. Can you take a look into that ? ^ permalink raw reply [flat|nested] 19+ messages in thread
* MX6sabresd broken since v2019.04 2021-02-01 13:01 ` Marek Vasut @ 2021-02-01 13:09 ` Fabio Estevam 2021-02-01 13:20 ` Marek Vasut 0 siblings, 1 reply; 19+ messages in thread From: Fabio Estevam @ 2021-02-01 13:09 UTC (permalink / raw) To: u-boot On Mon, Feb 1, 2021 at 10:01 AM Marek Vasut <marex@denx.de> wrote: > I think > u-boot-with-spl.imx: SPL u-boot.uim FORCE > should really be > u-boot-with-spl.imx: SPL u-boot.img FORCE > under certain (which ?) conditions. > > Can you take a look into that ? I tried your suggestion and it boots now: U-Boot SPL 2021.01-dirty (Feb 01 2021 - 10:07:21 -0300) Trying to boot from MMC1 U-Boot 2021.01-dirty (Feb 01 2021 - 10:07:21 -0300) CPU: Freescale i.MX6Q rev1.2 996 MHz (running at 792 MHz) CPU: Automotive temperature grade (-40C to 125C) at 50C Reset cause: POR Model: Freescale i.MX6 Quad SABRE Smart Device Board I2C: ready DRAM: 1 GiB PMIC: PFUZE100 ID=0x10 MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 3 Loading Environment from MMC... *** Warning - bad CRC, using default environment No panel detected: default to Hannstar-XGA Display: Hannstar-XGA (1024x768) In: serial Out: serial Err: serial Net: eth0: ethernet at 2188000 Hit any key to stop autoboot: 0 ^ permalink raw reply [flat|nested] 19+ messages in thread
* MX6sabresd broken since v2019.04 2021-02-01 13:09 ` Fabio Estevam @ 2021-02-01 13:20 ` Marek Vasut 2021-02-01 13:30 ` Fabio Estevam 0 siblings, 1 reply; 19+ messages in thread From: Marek Vasut @ 2021-02-01 13:20 UTC (permalink / raw) To: u-boot On 2/1/21 2:09 PM, Fabio Estevam wrote: > On Mon, Feb 1, 2021 at 10:01 AM Marek Vasut <marex@denx.de> wrote: > >> I think >> u-boot-with-spl.imx: SPL u-boot.uim FORCE >> should really be >> u-boot-with-spl.imx: SPL u-boot.img FORCE >> under certain (which ?) conditions. >> >> Can you take a look into that ? > > I tried your suggestion and it boots now: > > U-Boot SPL 2021.01-dirty (Feb 01 2021 - 10:07:21 -0300) > Trying to boot from MMC1 > > > U-Boot 2021.01-dirty (Feb 01 2021 - 10:07:21 -0300) But, it also likely breaks other boards, which still use plain uImage instead of fitImage. So there needs to be some conditional in the Makefile. Something like this maybe ? diff --git a/arch/arm/mach-imx/Makefile b/arch/arm/mach-imx/Makefile index 1aa26a50ad..e6b4654cd3 100644 --- a/arch/arm/mach-imx/Makefile +++ b/arch/arm/mach-imx/Makefile @@ -202,10 +202,10 @@ append = cat $(filter-out $< $(PHONY), $^) >> $@ quiet_cmd_pad_cat = CAT $@ cmd_pad_cat = $(cmd_objcopy) && $(append) || rm -f $@ -u-boot-with-spl.imx: SPL u-boot.uim FORCE +u-boot-with-spl.imx: SPL $(if $(CONFIG_OF_SEPARATE),u-boot.img,u-boot.uim) FORCE $(call if_changed,pad_cat) -u-boot-with-nand-spl.imx: spl/u-boot-nand-spl.imx u-boot.uim FORCE +u-boot-with-nand-spl.imx: spl/u-boot-nand-spl.imx $(if $(CONFIG_OF_SEPARATE),u-boot.img,u-boot.uim) FORCE $(call if_changed,pad_cat) quiet_cmd_u-boot-nand-spl_imx = GEN $@ ^ permalink raw reply related [flat|nested] 19+ messages in thread
* MX6sabresd broken since v2019.04 2021-02-01 13:20 ` Marek Vasut @ 2021-02-01 13:30 ` Fabio Estevam 2021-02-01 15:01 ` Marek Vasut 0 siblings, 1 reply; 19+ messages in thread From: Fabio Estevam @ 2021-02-01 13:30 UTC (permalink / raw) To: u-boot On Mon, Feb 1, 2021 at 10:20 AM Marek Vasut <marex@denx.de> wrote: > But, it also likely breaks other boards, which still use plain uImage > instead of fitImage. So there needs to be some conditional in the Makefile. > > Something like this maybe ? It makes mx6sabresd to boot: Tested-by: Fabio Estevam <festevam@gmail.com> ^ permalink raw reply [flat|nested] 19+ messages in thread
* MX6sabresd broken since v2019.04 2021-02-01 13:30 ` Fabio Estevam @ 2021-02-01 15:01 ` Marek Vasut 2021-02-01 16:29 ` Fabio Estevam 0 siblings, 1 reply; 19+ messages in thread From: Marek Vasut @ 2021-02-01 15:01 UTC (permalink / raw) To: u-boot On 2/1/21 2:30 PM, Fabio Estevam wrote: > On Mon, Feb 1, 2021 at 10:20 AM Marek Vasut <marex@denx.de> wrote: > >> But, it also likely breaks other boards, which still use plain uImage >> instead of fitImage. So there needs to be some conditional in the Makefile. >> >> Something like this maybe ? > > It makes mx6sabresd to boot: > > Tested-by: Fabio Estevam <festevam@gmail.com> I posted a patch, you are on CC, thanks. Can you please add this u-boot-with-spl.imx into the NXP test matrix ? ^ permalink raw reply [flat|nested] 19+ messages in thread
* MX6sabresd broken since v2019.04 2021-02-01 15:01 ` Marek Vasut @ 2021-02-01 16:29 ` Fabio Estevam 2021-02-01 16:36 ` Marek Vasut 0 siblings, 1 reply; 19+ messages in thread From: Fabio Estevam @ 2021-02-01 16:29 UTC (permalink / raw) To: u-boot Hi Marek, On Mon, Feb 1, 2021 at 12:01 PM Marek Vasut <marex@denx.de> wrote: > I posted a patch, you are on CC, thanks. > > Can you please add this u-boot-with-spl.imx into the NXP test matrix ? I am not aware of any NXP boot farm tests being done in U-Boot. Maybe Peng can comment. I know Heiko tests wandboard on his boot infrastructure. Maybe he could add u-boot-with-spl.imx there? ^ permalink raw reply [flat|nested] 19+ messages in thread
* MX6sabresd broken since v2019.04 2021-02-01 16:29 ` Fabio Estevam @ 2021-02-01 16:36 ` Marek Vasut 2021-02-01 17:40 ` Fabio Estevam 0 siblings, 1 reply; 19+ messages in thread From: Marek Vasut @ 2021-02-01 16:36 UTC (permalink / raw) To: u-boot On 2/1/21 5:29 PM, Fabio Estevam wrote: > Hi Marek, > > On Mon, Feb 1, 2021 at 12:01 PM Marek Vasut <marex@denx.de> wrote: > >> I posted a patch, you are on CC, thanks. >> >> Can you please add this u-boot-with-spl.imx into the NXP test matrix ? > > I am not aware of any NXP boot farm tests being done in U-Boot. Maybe > Peng can comment. > > I know Heiko tests wandboard on his boot infrastructure. Maybe he > could add u-boot-with-spl.imx there? I don't think WB uses OF_SEPARATE with fitImages, so maybe there its not applicable at all ? ^ permalink raw reply [flat|nested] 19+ messages in thread
* MX6sabresd broken since v2019.04 2021-02-01 16:36 ` Marek Vasut @ 2021-02-01 17:40 ` Fabio Estevam 2021-02-02 14:07 ` Heiko Schocher 0 siblings, 1 reply; 19+ messages in thread From: Fabio Estevam @ 2021-02-01 17:40 UTC (permalink / raw) To: u-boot On Mon, Feb 1, 2021 at 1:36 PM Marek Vasut <marex@denx.de> wrote: > I don't think WB uses OF_SEPARATE with fitImages, so maybe there its not > applicable at all ? Wandboard does use OF_SEPARATE and FIT. I have just tested flashing u-boot-with-spl.imx into a SD card and booting a wandboard. It does behave the same as mx6sabresd: - Fails to boot without your patch - Boots fine with your patch So, yes, wandboard can be used to test u-boot-with-spl.imx and avoid future regressions in Heiko's boot farm. ^ permalink raw reply [flat|nested] 19+ messages in thread
* MX6sabresd broken since v2019.04 2021-02-01 17:40 ` Fabio Estevam @ 2021-02-02 14:07 ` Heiko Schocher 2021-02-02 14:12 ` Fabio Estevam 0 siblings, 1 reply; 19+ messages in thread From: Heiko Schocher @ 2021-02-02 14:07 UTC (permalink / raw) To: u-boot Hello Fabio, Am 01.02.21 um 18:40 schrieb Fabio Estevam: > On Mon, Feb 1, 2021 at 1:36 PM Marek Vasut <marex@denx.de> wrote: > >> I don't think WB uses OF_SEPARATE with fitImages, so maybe there its not >> applicable at all ? > > Wandboard does use OF_SEPARATE and FIT. > > I have just tested flashing u-boot-with-spl.imx into a SD card and > booting a wandboard. > > It does behave the same as mx6sabresd: > > - Fails to boot without your patch > - Boots fine with your patch > > So, yes, wandboard can be used to test u-boot-with-spl.imx and avoid > future regressions in Heiko's boot farm. Last build from this morning: http://xeidos.ddns.net/ubtestresults/result/777 You find log here: http://xeidos.ddns.net/ubtestresults/result/files/results/777/tbot.log I use currently SPL and u-boot.img ... seems I have to switch to above image ... currently I have a lot of load on my desk, so may this takes some time ... sorry bye, Heiko [1] extract part "update SPL and u-boot.img on wandboard" from logfile: ? ? ??[wandboard-uboot] run load_spl ? ? ? ## ethernet at 2188000 Waiting for PHY auto negotiation to complete.... done ? ? ? ## Using ethernet at 2188000 device ? ? ? ## TFTP from server 192.168.3.1; our IP address is 192.168.3.21 ? ? ? ## Filename 'wandboard/tbot/SPL'. ? ? ? ## Load address: 0x12000000 ? ? ? ## Loading: *\b#### ? ? ? ## ? ? ? ## 1.6 MiB/s ? ? ? ## ? ? ? ## done ? ? ? ## Bytes transferred = 48128 (bc00 hex) ? ? ? ## ? ? ??[wandboard-uboot] run upd_spl ? ? ? ## switch to partitions #0, OK ? ? ? ## mmc0 is current device ? ? ? ## ? ? ? ## MMC write: dev # 0, block # 2, count 95 ... 95 blocks written: OK ? ? ??[wandboard-uboot] run cmp_spl ? ? ? ## Using ethernet at 2188000 device ? ? ? ## ? ? ? ## TFTP from server 192.168.3.1; our IP address is 192.168.3.21 ? ? ? ## Filename 'wandboard/tbot/SPL'. ? ? ? ## ? ? ? ## Load address: 0x12000000 ? ? ? ## Loading: *\b#### ? ? ? ## 2.9 MiB/s ? ? ? ## ? ? ? ## done ? ? ? ## Bytes transferred = 48128 (bc00 hex) ? ? ? ## ? ? ? ## ? ? ? ## ? ? ? ## MMC read: dev # 0, block # 2, count 95 ... 95 blocks read: OK ? ? ? ## ? ? ? ## Total of 48128 byte(s) were the same ? ? ? ## ? ? ??[wandboard-uboot] run load_ub ? ? ? ## Using ethernet at 2188000 device ? ? ? ## ? ? ? ## TFTP from server 192.168.3.1; our IP address is 192.168.3.21 ? ? ? ## Filename 'wandboard/tbot/u-boot.img'. ? ? ? ## ? ? ? ## Load address: 0x12000000 ? ? ? ## Loading: *\b######################################## ? ? ? ## ? ? ? ## 2.9 MiB/s ? ? ? ## done ? ? ? ## Bytes transferred = 577444 (8cfa4 hex) ? ? ? ## ? ? ??[wandboard-uboot] run upd_ub ? ? ? ## switch to partitions #0, OK ? ? ? ## mmc0 is current device ? ? ? ## ? ? ? ## MMC write: dev # 0, block # 138, count 1128 ... 1128 blocks written: OK ? ? ? ## ? ? ??[wandboard-uboot] run cmp_ub ? ? ? ## Using ethernet at 2188000 device ? ? ? ## ? ? ? ## TFTP from server 192.168.3.1; our IP address is 192.168.3.21 ? ? ? ## ? ? ? ## Filename 'wandboard/tbot/u-boot.img'. ? ? ? ## Load address: 0x12000000 ? ? ? ## ? ? ? ## Loading: *\b######################################## ? ? ? ## 2.5 MiB/s ? ? ? ## done ? ? ? ## Bytes transferred = 577444 (8cfa4 hex) ? ? ? ## ? ? ? ## MMC read: dev # 0, block # 138, count 1128 ... 1128 blocks read: OK ? ? ? ## Total of 577444 byte(s) were the same -- DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-52 Fax: +49-8142-66989-80 Email: hs at denx.de ^ permalink raw reply [flat|nested] 19+ messages in thread
* MX6sabresd broken since v2019.04 2021-02-02 14:07 ` Heiko Schocher @ 2021-02-02 14:12 ` Fabio Estevam 2021-02-02 14:22 ` Heiko Schocher 0 siblings, 1 reply; 19+ messages in thread From: Fabio Estevam @ 2021-02-02 14:12 UTC (permalink / raw) To: u-boot Hi Heiko, On Tue, Feb 2, 2021 at 11:08 AM Heiko Schocher <hs@denx.de> wrote: > I use currently SPL and u-boot.img ... seems I have to switch > to above image ... currently I have a lot of load on my desk, > so may this takes some time ... sorry Sure, no problem. The idea is to keep testing SPL and u-boot.img like you currently do and add an extra boot test that also tests u-boot-with-spl.imx. This would allows to catch regressions with the u-boot-with-spl.imx format too. Thanks ^ permalink raw reply [flat|nested] 19+ messages in thread
* MX6sabresd broken since v2019.04 2021-02-02 14:12 ` Fabio Estevam @ 2021-02-02 14:22 ` Heiko Schocher 0 siblings, 0 replies; 19+ messages in thread From: Heiko Schocher @ 2021-02-02 14:22 UTC (permalink / raw) To: u-boot Hello Fabio, Am 02.02.21 um 15:12 schrieb Fabio Estevam: > Hi Heiko, > > On Tue, Feb 2, 2021 at 11:08 AM Heiko Schocher <hs@denx.de> wrote: > >> I use currently SPL and u-boot.img ... seems I have to switch >> to above image ... currently I have a lot of load on my desk, >> so may this takes some time ... sorry > > Sure, no problem. > > The idea is to keep testing SPL and u-boot.img like you currently do > and add an extra boot test that also tests u-boot-with-spl.imx. > > This would allows to catch regressions with the u-boot-with-spl.imx format too. Ah, okay, yes this should be doable also ... bye, Heiko -- DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-52 Fax: +49-8142-66989-80 Email: hs at denx.de ^ permalink raw reply [flat|nested] 19+ messages in thread
end of thread, other threads:[~2021-02-02 14:22 UTC | newest] Thread overview: 19+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2021-02-01 10:59 MX6sabresd broken since v2019.04 Marek Vasut 2021-02-01 11:07 ` Fabio Estevam 2021-02-01 11:28 ` Marek Vasut 2021-02-01 11:37 ` Fabio Estevam 2021-02-01 11:58 ` Marek Vasut 2021-02-01 12:13 ` Fabio Estevam 2021-02-01 12:17 ` Marek Vasut 2021-02-01 12:22 ` Fabio Estevam 2021-02-01 13:01 ` Marek Vasut 2021-02-01 13:09 ` Fabio Estevam 2021-02-01 13:20 ` Marek Vasut 2021-02-01 13:30 ` Fabio Estevam 2021-02-01 15:01 ` Marek Vasut 2021-02-01 16:29 ` Fabio Estevam 2021-02-01 16:36 ` Marek Vasut 2021-02-01 17:40 ` Fabio Estevam 2021-02-02 14:07 ` Heiko Schocher 2021-02-02 14:12 ` Fabio Estevam 2021-02-02 14:22 ` Heiko Schocher
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.