* [PATCH v7 0/3] exynos: arch: add support for exynos5260 SoC @ 2014-04-03 10:00 ` Rahul Sharma 0 siblings, 0 replies; 20+ messages in thread From: Rahul Sharma @ 2014-04-03 10:00 UTC (permalink / raw) To: linux-samsung-soc Cc: devicetree, linux-arm-kernel, kgene.kim, tomasz.figa, joshi, r.sh.open, Rahul Sharma From: Rahul Sharma <Rahul.Sharma@samsung.com> v7: 1) Renamed board file V6: 1) Renamed mmc nodes. 2) Removed PHY clocks from DT and put them inside clock driver. 3) Added clock-cells property for all fixed clocks. 4) Removed spdif_ext_clk fixed rate clock. V5: 1) Removed SYSRAM related code. 2) Fixed mct clocks. 3) Add SoC and Board specifc fixed-rate clocks in respective files. V4: 1) Removed duplicate MMC Soc property from Board file. V3: 1) Addressed review comments from Tomasz figa. V2: 1) Split up DT patch into SoC and Board patch. This series is dependent on Sachin's patch "ARM: EXYNOS: Consolidate Kconfig entries" This series is based on Kukjin's for-next branch at http://git.kernel.org/?p=linux/kernel/git/kgene/linux-samsung.git Pankaj Dubey (1): ARM: EXYNOS: initial board support for exynos5260 SoC Rahul Sharma (2): ARM: dts: add dts files for exynos5260 SoC ARM: dts: add dts files for xyref5260 board arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/exynos5260-pinctrl.dtsi | 574 ++++++++++++++++++++++++++++ arch/arm/boot/dts/exynos5260-xyref5260.dts | 103 +++++ arch/arm/boot/dts/exynos5260.dtsi | 304 +++++++++++++++ arch/arm/mach-exynos/Kconfig | 5 + arch/arm/mach-exynos/exynos.c | 1 + 6 files changed, 988 insertions(+) create mode 100644 arch/arm/boot/dts/exynos5260-pinctrl.dtsi create mode 100644 arch/arm/boot/dts/exynos5260-xyref5260.dts create mode 100644 arch/arm/boot/dts/exynos5260.dtsi -- 1.7.9.5 ^ permalink raw reply [flat|nested] 20+ messages in thread
* [PATCH v7 0/3] exynos: arch: add support for exynos5260 SoC @ 2014-04-03 10:00 ` Rahul Sharma 0 siblings, 0 replies; 20+ messages in thread From: Rahul Sharma @ 2014-04-03 10:00 UTC (permalink / raw) To: linux-arm-kernel From: Rahul Sharma <Rahul.Sharma@samsung.com> v7: 1) Renamed board file V6: 1) Renamed mmc nodes. 2) Removed PHY clocks from DT and put them inside clock driver. 3) Added clock-cells property for all fixed clocks. 4) Removed spdif_ext_clk fixed rate clock. V5: 1) Removed SYSRAM related code. 2) Fixed mct clocks. 3) Add SoC and Board specifc fixed-rate clocks in respective files. V4: 1) Removed duplicate MMC Soc property from Board file. V3: 1) Addressed review comments from Tomasz figa. V2: 1) Split up DT patch into SoC and Board patch. This series is dependent on Sachin's patch "ARM: EXYNOS: Consolidate Kconfig entries" This series is based on Kukjin's for-next branch at http://git.kernel.org/?p=linux/kernel/git/kgene/linux-samsung.git Pankaj Dubey (1): ARM: EXYNOS: initial board support for exynos5260 SoC Rahul Sharma (2): ARM: dts: add dts files for exynos5260 SoC ARM: dts: add dts files for xyref5260 board arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/exynos5260-pinctrl.dtsi | 574 ++++++++++++++++++++++++++++ arch/arm/boot/dts/exynos5260-xyref5260.dts | 103 +++++ arch/arm/boot/dts/exynos5260.dtsi | 304 +++++++++++++++ arch/arm/mach-exynos/Kconfig | 5 + arch/arm/mach-exynos/exynos.c | 1 + 6 files changed, 988 insertions(+) create mode 100644 arch/arm/boot/dts/exynos5260-pinctrl.dtsi create mode 100644 arch/arm/boot/dts/exynos5260-xyref5260.dts create mode 100644 arch/arm/boot/dts/exynos5260.dtsi -- 1.7.9.5 ^ permalink raw reply [flat|nested] 20+ messages in thread
[parent not found: <1396519224-18712-1-git-send-email-rahul.sharma-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>]
* [PATCH v7 1/3] ARM: EXYNOS: initial board support for exynos5260 SoC 2014-04-03 10:00 ` Rahul Sharma @ 2014-04-03 10:00 ` Rahul Sharma -1 siblings, 0 replies; 20+ messages in thread From: Rahul Sharma @ 2014-04-03 10:00 UTC (permalink / raw) To: linux-samsung-soc-u79uwXL29TY76Z2rM5mHXA Cc: devicetree-u79uwXL29TY76Z2rM5mHXA, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, kgene.kim-Sze3O3UU22JBDgjK7y7TUQ, tomasz.figa-Re5JQEeQqe8AvxtiuMwx3w, joshi-Sze3O3UU22JBDgjK7y7TUQ, r.sh.open-Re5JQEeQqe8AvxtiuMwx3w, Pankaj Dubey, Rahul Sharma From: Pankaj Dubey <pankaj.dubey-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org> This patch add basic arch side support for exynos5260 SoC. Signed-off-by: Pankaj Dubey <pankaj.dubey-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org> Signed-off-by: Rahul Sharma <rahul.sharma-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org> Reviewed-by: Tomasz Figa <t.figa-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org> --- arch/arm/mach-exynos/Kconfig | 5 +++++ arch/arm/mach-exynos/exynos.c | 1 + 2 files changed, 6 insertions(+) diff --git a/arch/arm/mach-exynos/Kconfig b/arch/arm/mach-exynos/Kconfig index 5c34dc2..6c48844 100644 --- a/arch/arm/mach-exynos/Kconfig +++ b/arch/arm/mach-exynos/Kconfig @@ -51,6 +51,11 @@ config SOC_EXYNOS5250 default y depends on ARCH_EXYNOS5 +config SOC_EXYNOS5260 + bool "SAMSUNG EXYNOS5260" + default y + depends on ARCH_EXYNOS5 + config SOC_EXYNOS5420 bool "SAMSUNG EXYNOS5420" default y diff --git a/arch/arm/mach-exynos/exynos.c b/arch/arm/mach-exynos/exynos.c index b567361..5324051 100644 --- a/arch/arm/mach-exynos/exynos.c +++ b/arch/arm/mach-exynos/exynos.c @@ -374,6 +374,7 @@ static char const *exynos_dt_compat[] __initconst = { "samsung,exynos4412", "samsung,exynos5", "samsung,exynos5250", + "samsung,exynos5260", "samsung,exynos5420", "samsung,exynos5440", NULL -- 1.7.9.5 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v7 1/3] ARM: EXYNOS: initial board support for exynos5260 SoC @ 2014-04-03 10:00 ` Rahul Sharma 0 siblings, 0 replies; 20+ messages in thread From: Rahul Sharma @ 2014-04-03 10:00 UTC (permalink / raw) To: linux-arm-kernel From: Pankaj Dubey <pankaj.dubey@samsung.com> This patch add basic arch side support for exynos5260 SoC. Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com> Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com> Reviewed-by: Tomasz Figa <t.figa@samsung.com> --- arch/arm/mach-exynos/Kconfig | 5 +++++ arch/arm/mach-exynos/exynos.c | 1 + 2 files changed, 6 insertions(+) diff --git a/arch/arm/mach-exynos/Kconfig b/arch/arm/mach-exynos/Kconfig index 5c34dc2..6c48844 100644 --- a/arch/arm/mach-exynos/Kconfig +++ b/arch/arm/mach-exynos/Kconfig @@ -51,6 +51,11 @@ config SOC_EXYNOS5250 default y depends on ARCH_EXYNOS5 +config SOC_EXYNOS5260 + bool "SAMSUNG EXYNOS5260" + default y + depends on ARCH_EXYNOS5 + config SOC_EXYNOS5420 bool "SAMSUNG EXYNOS5420" default y diff --git a/arch/arm/mach-exynos/exynos.c b/arch/arm/mach-exynos/exynos.c index b567361..5324051 100644 --- a/arch/arm/mach-exynos/exynos.c +++ b/arch/arm/mach-exynos/exynos.c @@ -374,6 +374,7 @@ static char const *exynos_dt_compat[] __initconst = { "samsung,exynos4412", "samsung,exynos5", "samsung,exynos5250", + "samsung,exynos5260", "samsung,exynos5420", "samsung,exynos5440", NULL -- 1.7.9.5 ^ permalink raw reply related [flat|nested] 20+ messages in thread
* Re: [PATCH v7 1/3] ARM: EXYNOS: initial board support for exynos5260 SoC 2014-04-03 10:00 ` Rahul Sharma @ 2014-04-07 8:38 ` Sachin Kamat -1 siblings, 0 replies; 20+ messages in thread From: Sachin Kamat @ 2014-04-07 8:38 UTC (permalink / raw) To: Rahul Sharma Cc: linux-samsung-soc, devicetree, linux-arm-kernel, Kukjin Kim, Tomasz Figa, sunil joshi, Rahul Sharma, Pankaj Dubey Hi Rahul, On 3 April 2014 15:30, Rahul Sharma <rahul.sharma@samsung.com> wrote: > From: Pankaj Dubey <pankaj.dubey@samsung.com> > > This patch add basic arch side support for exynos5260 SoC. <snip> > @@ -374,6 +374,7 @@ static char const *exynos_dt_compat[] __initconst = { > "samsung,exynos4412", > "samsung,exynos5", > "samsung,exynos5250", > + "samsung,exynos5260", I don't think we should be adding this as we do not yet have any soc specific quirk. Compatibility to generic string, "samsung,exynos5" should be sufficient. -- With warm regards, Sachin ^ permalink raw reply [flat|nested] 20+ messages in thread
* [PATCH v7 1/3] ARM: EXYNOS: initial board support for exynos5260 SoC @ 2014-04-07 8:38 ` Sachin Kamat 0 siblings, 0 replies; 20+ messages in thread From: Sachin Kamat @ 2014-04-07 8:38 UTC (permalink / raw) To: linux-arm-kernel Hi Rahul, On 3 April 2014 15:30, Rahul Sharma <rahul.sharma@samsung.com> wrote: > From: Pankaj Dubey <pankaj.dubey@samsung.com> > > This patch add basic arch side support for exynos5260 SoC. <snip> > @@ -374,6 +374,7 @@ static char const *exynos_dt_compat[] __initconst = { > "samsung,exynos4412", > "samsung,exynos5", > "samsung,exynos5250", > + "samsung,exynos5260", I don't think we should be adding this as we do not yet have any soc specific quirk. Compatibility to generic string, "samsung,exynos5" should be sufficient. -- With warm regards, Sachin ^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH v7 1/3] ARM: EXYNOS: initial board support for exynos5260 SoC 2014-04-07 8:38 ` Sachin Kamat @ 2014-04-09 9:04 ` Tomasz Figa -1 siblings, 0 replies; 20+ messages in thread From: Tomasz Figa @ 2014-04-09 9:04 UTC (permalink / raw) To: Sachin Kamat, Rahul Sharma Cc: linux-samsung-soc, devicetree, linux-arm-kernel, Kukjin Kim, Tomasz Figa, sunil joshi, Rahul Sharma, Pankaj Dubey On 07.04.2014 10:38, Sachin Kamat wrote: > Hi Rahul, > > On 3 April 2014 15:30, Rahul Sharma <rahul.sharma@samsung.com> wrote: >> From: Pankaj Dubey <pankaj.dubey@samsung.com> >> >> This patch add basic arch side support for exynos5260 SoC. > <snip> > >> @@ -374,6 +374,7 @@ static char const *exynos_dt_compat[] __initconst = { >> "samsung,exynos4412", >> "samsung,exynos5", >> "samsung,exynos5250", >> + "samsung,exynos5260", > > I don't think we should be adding this as we do not yet have any soc > specific quirk. > Compatibility to generic string, "samsung,exynos5" should be sufficient. > Yes. Unless a SoC specific quirk that needs to be handled at such low level stage emerges, there is no need to add such compatible string to the kernel. Best regards, Tomasz ^ permalink raw reply [flat|nested] 20+ messages in thread
* [PATCH v7 1/3] ARM: EXYNOS: initial board support for exynos5260 SoC @ 2014-04-09 9:04 ` Tomasz Figa 0 siblings, 0 replies; 20+ messages in thread From: Tomasz Figa @ 2014-04-09 9:04 UTC (permalink / raw) To: linux-arm-kernel On 07.04.2014 10:38, Sachin Kamat wrote: > Hi Rahul, > > On 3 April 2014 15:30, Rahul Sharma <rahul.sharma@samsung.com> wrote: >> From: Pankaj Dubey <pankaj.dubey@samsung.com> >> >> This patch add basic arch side support for exynos5260 SoC. > <snip> > >> @@ -374,6 +374,7 @@ static char const *exynos_dt_compat[] __initconst = { >> "samsung,exynos4412", >> "samsung,exynos5", >> "samsung,exynos5250", >> + "samsung,exynos5260", > > I don't think we should be adding this as we do not yet have any soc > specific quirk. > Compatibility to generic string, "samsung,exynos5" should be sufficient. > Yes. Unless a SoC specific quirk that needs to be handled at such low level stage emerges, there is no need to add such compatible string to the kernel. Best regards, Tomasz ^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH v7 1/3] ARM: EXYNOS: initial board support for exynos5260 SoC 2014-04-09 9:04 ` Tomasz Figa @ 2014-04-09 9:15 ` Rahul Sharma -1 siblings, 0 replies; 20+ messages in thread From: Rahul Sharma @ 2014-04-09 9:15 UTC (permalink / raw) To: Tomasz Figa Cc: Sachin Kamat, Rahul Sharma, linux-samsung-soc, devicetree, linux-arm-kernel, Kukjin Kim, Tomasz Figa, sunil joshi, Pankaj Dubey On 9 April 2014 14:34, Tomasz Figa <t.figa@samsung.com> wrote: > On 07.04.2014 10:38, Sachin Kamat wrote: >> >> Hi Rahul, >> >> On 3 April 2014 15:30, Rahul Sharma <rahul.sharma@samsung.com> wrote: >>> >>> From: Pankaj Dubey <pankaj.dubey@samsung.com> >>> >>> This patch add basic arch side support for exynos5260 SoC. >> >> <snip> >> >>> @@ -374,6 +374,7 @@ static char const *exynos_dt_compat[] __initconst = { >>> "samsung,exynos4412", >>> "samsung,exynos5", >>> "samsung,exynos5250", >>> + "samsung,exynos5260", >> >> >> I don't think we should be adding this as we do not yet have any soc >> specific quirk. >> Compatibility to generic string, "samsung,exynos5" should be sufficient. >> > > Yes. Unless a SoC specific quirk that needs to be handled at such low level > stage emerges, there is no need to add such compatible string to the kernel. > Thanks Sachin, Tomasz, I will change this. Regards, Rahul Sharma. > Best regards, > Tomasz ^ permalink raw reply [flat|nested] 20+ messages in thread
* [PATCH v7 1/3] ARM: EXYNOS: initial board support for exynos5260 SoC @ 2014-04-09 9:15 ` Rahul Sharma 0 siblings, 0 replies; 20+ messages in thread From: Rahul Sharma @ 2014-04-09 9:15 UTC (permalink / raw) To: linux-arm-kernel On 9 April 2014 14:34, Tomasz Figa <t.figa@samsung.com> wrote: > On 07.04.2014 10:38, Sachin Kamat wrote: >> >> Hi Rahul, >> >> On 3 April 2014 15:30, Rahul Sharma <rahul.sharma@samsung.com> wrote: >>> >>> From: Pankaj Dubey <pankaj.dubey@samsung.com> >>> >>> This patch add basic arch side support for exynos5260 SoC. >> >> <snip> >> >>> @@ -374,6 +374,7 @@ static char const *exynos_dt_compat[] __initconst = { >>> "samsung,exynos4412", >>> "samsung,exynos5", >>> "samsung,exynos5250", >>> + "samsung,exynos5260", >> >> >> I don't think we should be adding this as we do not yet have any soc >> specific quirk. >> Compatibility to generic string, "samsung,exynos5" should be sufficient. >> > > Yes. Unless a SoC specific quirk that needs to be handled at such low level > stage emerges, there is no need to add such compatible string to the kernel. > Thanks Sachin, Tomasz, I will change this. Regards, Rahul Sharma. > Best regards, > Tomasz ^ permalink raw reply [flat|nested] 20+ messages in thread
* [PATCH v7 2/3] ARM: dts: add dts files for exynos5260 SoC 2014-04-03 10:00 ` Rahul Sharma @ 2014-04-03 10:00 ` Rahul Sharma -1 siblings, 0 replies; 20+ messages in thread From: Rahul Sharma @ 2014-04-03 10:00 UTC (permalink / raw) To: linux-samsung-soc Cc: devicetree, linux-arm-kernel, kgene.kim, tomasz.figa, joshi, r.sh.open, Rahul Sharma, Pankaj Dubey, Arun Kumar K The patch adds the dts files for exynos5260. Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com> Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com> Signed-off-by: Arun Kumar K <arun.kk@samsung.com> Reviewed-by: Tomasz Figa <t.figa@samsung.com> --- arch/arm/boot/dts/exynos5260-pinctrl.dtsi | 574 +++++++++++++++++++++++++++++ arch/arm/boot/dts/exynos5260.dtsi | 304 +++++++++++++++ 2 files changed, 878 insertions(+) create mode 100644 arch/arm/boot/dts/exynos5260-pinctrl.dtsi create mode 100644 arch/arm/boot/dts/exynos5260.dtsi diff --git a/arch/arm/boot/dts/exynos5260-pinctrl.dtsi b/arch/arm/boot/dts/exynos5260-pinctrl.dtsi new file mode 100644 index 0000000..f6ee55e --- /dev/null +++ b/arch/arm/boot/dts/exynos5260-pinctrl.dtsi @@ -0,0 +1,574 @@ +/* + * Samsung's Exynos5260 SoC pin-mux and pin-config device tree source + * + * Copyright (c) 2013 Samsung Electronics Co., Ltd. + * http://www.samsung.com + * + * Samsung's Exynos5260 SoC pin-mux and pin-config options are listed as device + * tree nodes are listed in this file. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#define PIN_PULL_NONE 0 +#define PIN_PULL_DOWN 1 +#define PIN_PULL_UP 3 + +&pinctrl_0 { + gpa0: gpa0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpa1: gpa1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpa2: gpa2 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpb0: gpb0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpb1: gpb1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpb2: gpb2 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpb3: gpb3 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpb4: gpb4 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpb5: gpb5 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpd0: gpd0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpd1: gpd1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpd2: gpd2 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpe0: gpe0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpe1: gpe1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpf0: gpf0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpf1: gpf1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpk0: gpk0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpx0: gpx0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpx1: gpx1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpx2: gpx2 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpx3: gpx3 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + uart0_data: uart0-data { + samsung,pins = "gpa0-0", "gpa0-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + uart0_fctl: uart0-fctl { + samsung,pins = "gpa0-2", "gpa0-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + uart1_data: uart1-data { + samsung,pins = "gpa1-0", "gpa1-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + uart1_fctl: uart1-fctl { + samsung,pins = "gpa1-2", "gpa1-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + uart2_data: uart2-data { + samsung,pins = "gpa1-4", "gpa1-5"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + spi0_bus: spi0-bus { + samsung,pins = "gpa2-0", "gpa2-2", "gpa2-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + spi1_bus: spi1-bus { + samsung,pins = "gpa2-4", "gpa2-6", "gpa2-7"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + usb3_vbus0_en: usb3-vbus0-en { + samsung,pins = "gpa2-4"; + samsung,pin-function = <1>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + i2s1_bus: i2s1-bus { + samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2", "gpb0-3", + "gpb0-4"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + pcm1_bus: pcm1-bus { + samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2", "gpb0-3", + "gpb0-4"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + spdif1_bus: spdif1-bus { + samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2"; + samsung,pin-function = <4>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + spi2_bus: spi2-bus { + samsung,pins = "gpb1-0", "gpb1-2", "gpb1-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c0_hs_bus: i2c0-hs-bus { + samsung,pins = "gpb3-0", "gpb3-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c1_hs_bus: i2c1-hs-bus { + samsung,pins = "gpb3-2", "gpb3-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c2_hs_bus: i2c2-hs-bus { + samsung,pins = "gpb3-4", "gpb3-5"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c3_hs_bus: i2c3-hs-bus { + samsung,pins = "gpb3-6", "gpb3-7"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c4_bus: i2c4-bus { + samsung,pins = "gpb4-0", "gpb4-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c5_bus: i2c5-bus { + samsung,pins = "gpb4-2", "gpb4-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c6_bus: i2c6-bus { + samsung,pins = "gpb4-4", "gpb4-5"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c7_bus: i2c7-bus { + samsung,pins = "gpb4-6", "gpb4-7"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c8_bus: i2c8-bus { + samsung,pins = "gpb5-0", "gpb5-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c9_bus: i2c9-bus { + samsung,pins = "gpb5-2", "gpb5-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c10_bus: i2c10-bus { + samsung,pins = "gpb5-4", "gpb5-5"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c11_bus: i2c11-bus { + samsung,pins = "gpb5-6", "gpb5-7"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + cam_gpio_a: cam-gpio-a { + samsung,pins = "gpe0-0", "gpe0-1", "gpe0-2", "gpe0-3", + "gpe0-4", "gpe0-5", "gpe0-6", "gpe0-7", + "gpe1-0", "gpe1-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + cam_gpio_b: cam-gpio-b { + samsung,pins = "gpf0-0", "gpf0-1", "gpf0-2", "gpf0-3", + "gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + cam_i2c1_bus: cam-i2c1-bus { + samsung,pins = "gpf0-2", "gpf0-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + cam_i2c0_bus: cam-i2c0-bus { + samsung,pins = "gpf0-0", "gpf0-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + cam_spi0_bus: cam-spi0-bus { + samsung,pins = "gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + cam_spi1_bus: cam-spi1-bus { + samsung,pins = "gpf1-4", "gpf1-5", "gpf1-6", "gpf1-7"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; +}; + +&pinctrl_1 { + gpc0: gpc0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpc1: gpc1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpc2: gpc2 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpc3: gpc3 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpc4: gpc4 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + sd0_clk: sd0-clk { + samsung,pins = "gpc0-0"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <3>; + }; + + sd0_cmd: sd0-cmd { + samsung,pins = "gpc0-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <3>; + }; + + sd0_bus1: sd0-bus-width1 { + samsung,pins = "gpc0-2"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd0_bus4: sd0-bus-width4 { + samsung,pins = "gpc0-3", "gpc0-4", "gpc0-5"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd0_bus8: sd0-bus-width8 { + samsung,pins = "gpc3-0", "gpc3-1", "gpc3-2", "gpc3-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd0_rdqs: sd0-rdqs { + samsung,pins = "gpc0-6"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd1_clk: sd1-clk { + samsung,pins = "gpc1-0"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <3>; + }; + + sd1_cmd: sd1-cmd { + samsung,pins = "gpc1-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <3>; + }; + + sd1_bus1: sd1-bus-width1 { + samsung,pins = "gpc1-2"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd1_bus4: sd1-bus-width4 { + samsung,pins = "gpc1-3", "gpc1-4", "gpc1-5"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd1_bus8: sd1-bus-width8 { + samsung,pins = "gpc4-0", "gpc4-1", "gpc4-2", "gpc4-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd2_clk: sd2-clk { + samsung,pins = "gpc2-0"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <3>; + }; + + sd2_cmd: sd2-cmd { + samsung,pins = "gpc2-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <3>; + }; + + sd2_cd: sd2-cd { + samsung,pins = "gpc2-2"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd2_bus1: sd2-bus-width1 { + samsung,pins = "gpc2-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd2_bus4: sd2-bus-width4 { + samsung,pins = "gpc2-4", "gpc2-5", "gpc2-6"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; +}; + +&pinctrl_2 { + gpz0: gpz0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpz1: gpz1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; +}; diff --git a/arch/arm/boot/dts/exynos5260.dtsi b/arch/arm/boot/dts/exynos5260.dtsi new file mode 100644 index 0000000..188a2ac --- /dev/null +++ b/arch/arm/boot/dts/exynos5260.dtsi @@ -0,0 +1,304 @@ +/* + * SAMSUNG EXYNOS5260 SoC device tree source + * + * Copyright (c) 2013 Samsung Electronics Co., Ltd. + * http://www.samsung.com + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include "skeleton.dtsi" + +#include <dt-bindings/clock/exynos5260-clk.h> + +/ { + compatible = "samsung,exynos5260"; + interrupt-parent = <&gic>; + + aliases { + pinctrl0 = &pinctrl_0; + pinctrl1 = &pinctrl_1; + pinctrl2 = &pinctrl_2; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x0>; + cci-control-port = <&cci_control1>; + }; + + cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x1>; + cci-control-port = <&cci_control1>; + }; + + cpu@100 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x100>; + cci-control-port = <&cci_control0>; + }; + + cpu@101 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x101>; + cci-control-port = <&cci_control0>; + }; + + cpu@102 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x102>; + cci-control-port = <&cci_control0>; + }; + + cpu@103 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x103>; + cci-control-port = <&cci_control0>; + }; + }; + + soc: soc { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + clock_top: clock-controller@10010000 { + compatible = "samsung,exynos5260-clock-top"; + reg = <0x10010000 0x10000>; + #clock-cells = <1>; + }; + + clock_peri: clock-controller@10200000 { + compatible = "samsung,exynos5260-clock-peri"; + reg = <0x10200000 0x10000>; + #clock-cells = <1>; + }; + + clock_egl: clock-controller@10600000 { + compatible = "samsung,exynos5260-clock-egl"; + reg = <0x10600000 0x10000>; + #clock-cells = <1>; + }; + + clock_kfc: clock-controller@10700000 { + compatible = "samsung,exynos5260-clock-kfc"; + reg = <0x10700000 0x10000>; + #clock-cells = <1>; + }; + + clock_g2d: clock-controller@10A00000 { + compatible = "samsung,exynos5260-clock-g2d"; + reg = <0x10A00000 0x10000>; + #clock-cells = <1>; + }; + + clock_mif: clock-controller@10CE0000 { + compatible = "samsung,exynos5260-clock-mif"; + reg = <0x10CE0000 0x10000>; + #clock-cells = <1>; + }; + + clock_mfc: clock-controller@11090000 { + compatible = "samsung,exynos5260-clock-mfc"; + reg = <0x11090000 0x10000>; + #clock-cells = <1>; + }; + + clock_g3d: clock-controller@11830000 { + compatible = "samsung,exynos5260-clock-g3d"; + reg = <0x11830000 0x10000>; + #clock-cells = <1>; + }; + + clock_fsys: clock-controller@122E0000 { + compatible = "samsung,exynos5260-clock-fsys"; + reg = <0x122E0000 0x10000>; + #clock-cells = <1>; + }; + + clock_aud: clock-controller@128C0000 { + compatible = "samsung,exynos5260-clock-aud"; + reg = <0x128C0000 0x10000>; + #clock-cells = <1>; + }; + + clock_isp: clock-controller@133C0000 { + compatible = "samsung,exynos5260-clock-isp"; + reg = <0x133C0000 0x10000>; + #clock-cells = <1>; + }; + + clock_gscl: clock-controller@13F00000 { + compatible = "samsung,exynos5260-clock-gscl"; + reg = <0x13F00000 0x10000>; + #clock-cells = <1>; + }; + + clock_disp: clock-controller@14550000 { + compatible = "samsung,exynos5260-clock-disp"; + reg = <0x14550000 0x10000>; + #clock-cells = <1>; + }; + + gic: interrupt-controller@10481000 { + compatible = "arm,cortex-a15-gic", "arm,cortex-a9-gic"; + #interrupt-cells = <3>; + #address-cells = <0>; + #size-cells = <0>; + interrupt-controller; + reg = <0x10481000 0x1000>, + <0x10482000 0x1000>, + <0x10484000 0x2000>, + <0x10486000 0x2000>; + interrupts = <1 9 0xf04>; + }; + + chipid: chipid@10000000 { + compatible = "samsung,exynos4210-chipid"; + reg = <0x10000000 0x100>; + }; + + mct: mct@100B0000 { + compatible = "samsung,exynos4210-mct"; + reg = <0x100B0000 0x1000>; + clocks = <&fin_pll>, <&clock_peri PERI_CLK_MCT>; + clock-names = "fin_pll", "mct"; + interrupts = <0 104 0>, <0 105 0>, <0 106 0>, + <0 107 0>, <0 122 0>, <0 123 0>, + <0 124 0>, <0 125 0>, <0 126 0>, + <0 127 0>, <0 128 0>, <0 129 0>; + }; + + cci: cci@10F00000 { + compatible = "arm,cci-400"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x10F00000 0x1000>; + ranges = <0x0 0x10F00000 0x6000>; + + cci_control0: slave-if@4000 { + compatible = "arm,cci-400-ctrl-if"; + interface-type = "ace"; + reg = <0x4000 0x1000>; + }; + + cci_control1: slave-if@5000 { + compatible = "arm,cci-400-ctrl-if"; + interface-type = "ace"; + reg = <0x5000 0x1000>; + }; + }; + + pinctrl_0: pinctrl@11600000 { + compatible = "samsung,exynos5260-pinctrl"; + reg = <0x11600000 0x1000>; + interrupts = <0 79 0>; + + wakeup-interrupt-controller { + compatible = "samsung,exynos4210-wakeup-eint"; + interrupt-parent = <&gic>; + interrupts = <0 32 0>; + }; + }; + + pinctrl_1: pinctrl@12290000 { + compatible = "samsung,exynos5260-pinctrl"; + reg = <0x12290000 0x1000>; + interrupts = <0 157 0>; + }; + + pinctrl_2: pinctrl@128B0000 { + compatible = "samsung,exynos5260-pinctrl"; + reg = <0x128B0000 0x1000>; + interrupts = <0 243 0>; + }; + + uart0: serial@12C00000 { + compatible = "samsung,exynos4210-uart"; + reg = <0x12C00000 0x100>; + interrupts = <0 146 0>; + clocks = <&clock_peri PERI_CLK_UART0>, <&clock_peri PERI_SCLK_UART0>; + clock-names = "uart", "clk_uart_baud0"; + status = "disabled"; + }; + + uart1: serial@12C10000 { + compatible = "samsung,exynos4210-uart"; + reg = <0x12C10000 0x100>; + interrupts = <0 147 0>; + clocks = <&clock_peri PERI_CLK_UART1>, <&clock_peri PERI_SCLK_UART1>; + clock-names = "uart", "clk_uart_baud0"; + status = "disabled"; + }; + + uart2: serial@12C20000 { + compatible = "samsung,exynos4210-uart"; + reg = <0x12C20000 0x100>; + interrupts = <0 148 0>; + clocks = <&clock_peri PERI_CLK_UART2>, <&clock_peri PERI_SCLK_UART2>; + clock-names = "uart", "clk_uart_baud0"; + status = "disabled"; + }; + + uart3: serial@12860000 { + compatible = "samsung,exynos4210-uart"; + reg = <0x12860000 0x100>; + interrupts = <0 145 0>; + clocks = <&clock_aud AUD_CLK_AUD_UART>, <&clock_aud AUD_SCLK_AUD_UART>; + clock-names = "uart", "clk_uart_baud0"; + status = "disabled"; + }; + + mmc_0: mmc@12140000 { + compatible = "samsung,exynos5250-dw-mshc"; + reg = <0x12140000 0x2000>; + interrupts = <0 156 0>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clock_fsys FSYS_CLK_MMC0>, <&clock_top TOP_SCLK_MMC0>; + clock-names = "biu", "ciu"; + fifo-depth = <64>; + status = "disabled"; + }; + + mmc_1: mmc@12150000 { + compatible = "samsung,exynos5250-dw-mshc"; + reg = <0x12150000 0x2000>; + interrupts = <0 158 0>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clock_fsys FSYS_CLK_MMC1>, <&clock_top TOP_SCLK_MMC1>; + clock-names = "biu", "ciu"; + fifo-depth = <64>; + status = "disabled"; + }; + + mmc_2: mmc@12160000 { + compatible = "samsung,exynos5250-dw-mshc"; + reg = <0x12160000 0x2000>; + interrupts = <0 159 0>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clock_fsys FSYS_CLK_MMC2>, <&clock_top TOP_SCLK_MMC2>; + clock-names = "biu", "ciu"; + fifo-depth = <64>; + status = "disabled"; + }; + }; +}; + +#include "exynos5260-pinctrl.dtsi" -- 1.7.9.5 ^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v7 2/3] ARM: dts: add dts files for exynos5260 SoC @ 2014-04-03 10:00 ` Rahul Sharma 0 siblings, 0 replies; 20+ messages in thread From: Rahul Sharma @ 2014-04-03 10:00 UTC (permalink / raw) To: linux-arm-kernel The patch adds the dts files for exynos5260. Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com> Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com> Signed-off-by: Arun Kumar K <arun.kk@samsung.com> Reviewed-by: Tomasz Figa <t.figa@samsung.com> --- arch/arm/boot/dts/exynos5260-pinctrl.dtsi | 574 +++++++++++++++++++++++++++++ arch/arm/boot/dts/exynos5260.dtsi | 304 +++++++++++++++ 2 files changed, 878 insertions(+) create mode 100644 arch/arm/boot/dts/exynos5260-pinctrl.dtsi create mode 100644 arch/arm/boot/dts/exynos5260.dtsi diff --git a/arch/arm/boot/dts/exynos5260-pinctrl.dtsi b/arch/arm/boot/dts/exynos5260-pinctrl.dtsi new file mode 100644 index 0000000..f6ee55e --- /dev/null +++ b/arch/arm/boot/dts/exynos5260-pinctrl.dtsi @@ -0,0 +1,574 @@ +/* + * Samsung's Exynos5260 SoC pin-mux and pin-config device tree source + * + * Copyright (c) 2013 Samsung Electronics Co., Ltd. + * http://www.samsung.com + * + * Samsung's Exynos5260 SoC pin-mux and pin-config options are listed as device + * tree nodes are listed in this file. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#define PIN_PULL_NONE 0 +#define PIN_PULL_DOWN 1 +#define PIN_PULL_UP 3 + +&pinctrl_0 { + gpa0: gpa0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpa1: gpa1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpa2: gpa2 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpb0: gpb0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpb1: gpb1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpb2: gpb2 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpb3: gpb3 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpb4: gpb4 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpb5: gpb5 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpd0: gpd0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpd1: gpd1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpd2: gpd2 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpe0: gpe0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpe1: gpe1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpf0: gpf0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpf1: gpf1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpk0: gpk0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpx0: gpx0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpx1: gpx1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpx2: gpx2 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpx3: gpx3 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + uart0_data: uart0-data { + samsung,pins = "gpa0-0", "gpa0-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + uart0_fctl: uart0-fctl { + samsung,pins = "gpa0-2", "gpa0-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + uart1_data: uart1-data { + samsung,pins = "gpa1-0", "gpa1-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + uart1_fctl: uart1-fctl { + samsung,pins = "gpa1-2", "gpa1-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + uart2_data: uart2-data { + samsung,pins = "gpa1-4", "gpa1-5"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + spi0_bus: spi0-bus { + samsung,pins = "gpa2-0", "gpa2-2", "gpa2-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + spi1_bus: spi1-bus { + samsung,pins = "gpa2-4", "gpa2-6", "gpa2-7"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + usb3_vbus0_en: usb3-vbus0-en { + samsung,pins = "gpa2-4"; + samsung,pin-function = <1>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + i2s1_bus: i2s1-bus { + samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2", "gpb0-3", + "gpb0-4"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + pcm1_bus: pcm1-bus { + samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2", "gpb0-3", + "gpb0-4"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + spdif1_bus: spdif1-bus { + samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2"; + samsung,pin-function = <4>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + spi2_bus: spi2-bus { + samsung,pins = "gpb1-0", "gpb1-2", "gpb1-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c0_hs_bus: i2c0-hs-bus { + samsung,pins = "gpb3-0", "gpb3-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c1_hs_bus: i2c1-hs-bus { + samsung,pins = "gpb3-2", "gpb3-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c2_hs_bus: i2c2-hs-bus { + samsung,pins = "gpb3-4", "gpb3-5"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c3_hs_bus: i2c3-hs-bus { + samsung,pins = "gpb3-6", "gpb3-7"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c4_bus: i2c4-bus { + samsung,pins = "gpb4-0", "gpb4-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c5_bus: i2c5-bus { + samsung,pins = "gpb4-2", "gpb4-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c6_bus: i2c6-bus { + samsung,pins = "gpb4-4", "gpb4-5"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c7_bus: i2c7-bus { + samsung,pins = "gpb4-6", "gpb4-7"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c8_bus: i2c8-bus { + samsung,pins = "gpb5-0", "gpb5-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c9_bus: i2c9-bus { + samsung,pins = "gpb5-2", "gpb5-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c10_bus: i2c10-bus { + samsung,pins = "gpb5-4", "gpb5-5"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c11_bus: i2c11-bus { + samsung,pins = "gpb5-6", "gpb5-7"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + cam_gpio_a: cam-gpio-a { + samsung,pins = "gpe0-0", "gpe0-1", "gpe0-2", "gpe0-3", + "gpe0-4", "gpe0-5", "gpe0-6", "gpe0-7", + "gpe1-0", "gpe1-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + cam_gpio_b: cam-gpio-b { + samsung,pins = "gpf0-0", "gpf0-1", "gpf0-2", "gpf0-3", + "gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + cam_i2c1_bus: cam-i2c1-bus { + samsung,pins = "gpf0-2", "gpf0-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + cam_i2c0_bus: cam-i2c0-bus { + samsung,pins = "gpf0-0", "gpf0-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + cam_spi0_bus: cam-spi0-bus { + samsung,pins = "gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + cam_spi1_bus: cam-spi1-bus { + samsung,pins = "gpf1-4", "gpf1-5", "gpf1-6", "gpf1-7"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; +}; + +&pinctrl_1 { + gpc0: gpc0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpc1: gpc1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpc2: gpc2 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpc3: gpc3 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpc4: gpc4 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + sd0_clk: sd0-clk { + samsung,pins = "gpc0-0"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <3>; + }; + + sd0_cmd: sd0-cmd { + samsung,pins = "gpc0-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <3>; + }; + + sd0_bus1: sd0-bus-width1 { + samsung,pins = "gpc0-2"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd0_bus4: sd0-bus-width4 { + samsung,pins = "gpc0-3", "gpc0-4", "gpc0-5"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd0_bus8: sd0-bus-width8 { + samsung,pins = "gpc3-0", "gpc3-1", "gpc3-2", "gpc3-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd0_rdqs: sd0-rdqs { + samsung,pins = "gpc0-6"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd1_clk: sd1-clk { + samsung,pins = "gpc1-0"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <3>; + }; + + sd1_cmd: sd1-cmd { + samsung,pins = "gpc1-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <3>; + }; + + sd1_bus1: sd1-bus-width1 { + samsung,pins = "gpc1-2"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd1_bus4: sd1-bus-width4 { + samsung,pins = "gpc1-3", "gpc1-4", "gpc1-5"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd1_bus8: sd1-bus-width8 { + samsung,pins = "gpc4-0", "gpc4-1", "gpc4-2", "gpc4-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd2_clk: sd2-clk { + samsung,pins = "gpc2-0"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <3>; + }; + + sd2_cmd: sd2-cmd { + samsung,pins = "gpc2-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <3>; + }; + + sd2_cd: sd2-cd { + samsung,pins = "gpc2-2"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd2_bus1: sd2-bus-width1 { + samsung,pins = "gpc2-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd2_bus4: sd2-bus-width4 { + samsung,pins = "gpc2-4", "gpc2-5", "gpc2-6"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; +}; + +&pinctrl_2 { + gpz0: gpz0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpz1: gpz1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; +}; diff --git a/arch/arm/boot/dts/exynos5260.dtsi b/arch/arm/boot/dts/exynos5260.dtsi new file mode 100644 index 0000000..188a2ac --- /dev/null +++ b/arch/arm/boot/dts/exynos5260.dtsi @@ -0,0 +1,304 @@ +/* + * SAMSUNG EXYNOS5260 SoC device tree source + * + * Copyright (c) 2013 Samsung Electronics Co., Ltd. + * http://www.samsung.com + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include "skeleton.dtsi" + +#include <dt-bindings/clock/exynos5260-clk.h> + +/ { + compatible = "samsung,exynos5260"; + interrupt-parent = <&gic>; + + aliases { + pinctrl0 = &pinctrl_0; + pinctrl1 = &pinctrl_1; + pinctrl2 = &pinctrl_2; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu at 0 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x0>; + cci-control-port = <&cci_control1>; + }; + + cpu at 1 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x1>; + cci-control-port = <&cci_control1>; + }; + + cpu at 100 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x100>; + cci-control-port = <&cci_control0>; + }; + + cpu at 101 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x101>; + cci-control-port = <&cci_control0>; + }; + + cpu at 102 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x102>; + cci-control-port = <&cci_control0>; + }; + + cpu at 103 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x103>; + cci-control-port = <&cci_control0>; + }; + }; + + soc: soc { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + clock_top: clock-controller at 10010000 { + compatible = "samsung,exynos5260-clock-top"; + reg = <0x10010000 0x10000>; + #clock-cells = <1>; + }; + + clock_peri: clock-controller at 10200000 { + compatible = "samsung,exynos5260-clock-peri"; + reg = <0x10200000 0x10000>; + #clock-cells = <1>; + }; + + clock_egl: clock-controller at 10600000 { + compatible = "samsung,exynos5260-clock-egl"; + reg = <0x10600000 0x10000>; + #clock-cells = <1>; + }; + + clock_kfc: clock-controller at 10700000 { + compatible = "samsung,exynos5260-clock-kfc"; + reg = <0x10700000 0x10000>; + #clock-cells = <1>; + }; + + clock_g2d: clock-controller at 10A00000 { + compatible = "samsung,exynos5260-clock-g2d"; + reg = <0x10A00000 0x10000>; + #clock-cells = <1>; + }; + + clock_mif: clock-controller at 10CE0000 { + compatible = "samsung,exynos5260-clock-mif"; + reg = <0x10CE0000 0x10000>; + #clock-cells = <1>; + }; + + clock_mfc: clock-controller at 11090000 { + compatible = "samsung,exynos5260-clock-mfc"; + reg = <0x11090000 0x10000>; + #clock-cells = <1>; + }; + + clock_g3d: clock-controller at 11830000 { + compatible = "samsung,exynos5260-clock-g3d"; + reg = <0x11830000 0x10000>; + #clock-cells = <1>; + }; + + clock_fsys: clock-controller at 122E0000 { + compatible = "samsung,exynos5260-clock-fsys"; + reg = <0x122E0000 0x10000>; + #clock-cells = <1>; + }; + + clock_aud: clock-controller at 128C0000 { + compatible = "samsung,exynos5260-clock-aud"; + reg = <0x128C0000 0x10000>; + #clock-cells = <1>; + }; + + clock_isp: clock-controller at 133C0000 { + compatible = "samsung,exynos5260-clock-isp"; + reg = <0x133C0000 0x10000>; + #clock-cells = <1>; + }; + + clock_gscl: clock-controller at 13F00000 { + compatible = "samsung,exynos5260-clock-gscl"; + reg = <0x13F00000 0x10000>; + #clock-cells = <1>; + }; + + clock_disp: clock-controller at 14550000 { + compatible = "samsung,exynos5260-clock-disp"; + reg = <0x14550000 0x10000>; + #clock-cells = <1>; + }; + + gic: interrupt-controller at 10481000 { + compatible = "arm,cortex-a15-gic", "arm,cortex-a9-gic"; + #interrupt-cells = <3>; + #address-cells = <0>; + #size-cells = <0>; + interrupt-controller; + reg = <0x10481000 0x1000>, + <0x10482000 0x1000>, + <0x10484000 0x2000>, + <0x10486000 0x2000>; + interrupts = <1 9 0xf04>; + }; + + chipid: chipid at 10000000 { + compatible = "samsung,exynos4210-chipid"; + reg = <0x10000000 0x100>; + }; + + mct: mct at 100B0000 { + compatible = "samsung,exynos4210-mct"; + reg = <0x100B0000 0x1000>; + clocks = <&fin_pll>, <&clock_peri PERI_CLK_MCT>; + clock-names = "fin_pll", "mct"; + interrupts = <0 104 0>, <0 105 0>, <0 106 0>, + <0 107 0>, <0 122 0>, <0 123 0>, + <0 124 0>, <0 125 0>, <0 126 0>, + <0 127 0>, <0 128 0>, <0 129 0>; + }; + + cci: cci at 10F00000 { + compatible = "arm,cci-400"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x10F00000 0x1000>; + ranges = <0x0 0x10F00000 0x6000>; + + cci_control0: slave-if at 4000 { + compatible = "arm,cci-400-ctrl-if"; + interface-type = "ace"; + reg = <0x4000 0x1000>; + }; + + cci_control1: slave-if at 5000 { + compatible = "arm,cci-400-ctrl-if"; + interface-type = "ace"; + reg = <0x5000 0x1000>; + }; + }; + + pinctrl_0: pinctrl at 11600000 { + compatible = "samsung,exynos5260-pinctrl"; + reg = <0x11600000 0x1000>; + interrupts = <0 79 0>; + + wakeup-interrupt-controller { + compatible = "samsung,exynos4210-wakeup-eint"; + interrupt-parent = <&gic>; + interrupts = <0 32 0>; + }; + }; + + pinctrl_1: pinctrl at 12290000 { + compatible = "samsung,exynos5260-pinctrl"; + reg = <0x12290000 0x1000>; + interrupts = <0 157 0>; + }; + + pinctrl_2: pinctrl at 128B0000 { + compatible = "samsung,exynos5260-pinctrl"; + reg = <0x128B0000 0x1000>; + interrupts = <0 243 0>; + }; + + uart0: serial at 12C00000 { + compatible = "samsung,exynos4210-uart"; + reg = <0x12C00000 0x100>; + interrupts = <0 146 0>; + clocks = <&clock_peri PERI_CLK_UART0>, <&clock_peri PERI_SCLK_UART0>; + clock-names = "uart", "clk_uart_baud0"; + status = "disabled"; + }; + + uart1: serial at 12C10000 { + compatible = "samsung,exynos4210-uart"; + reg = <0x12C10000 0x100>; + interrupts = <0 147 0>; + clocks = <&clock_peri PERI_CLK_UART1>, <&clock_peri PERI_SCLK_UART1>; + clock-names = "uart", "clk_uart_baud0"; + status = "disabled"; + }; + + uart2: serial at 12C20000 { + compatible = "samsung,exynos4210-uart"; + reg = <0x12C20000 0x100>; + interrupts = <0 148 0>; + clocks = <&clock_peri PERI_CLK_UART2>, <&clock_peri PERI_SCLK_UART2>; + clock-names = "uart", "clk_uart_baud0"; + status = "disabled"; + }; + + uart3: serial at 12860000 { + compatible = "samsung,exynos4210-uart"; + reg = <0x12860000 0x100>; + interrupts = <0 145 0>; + clocks = <&clock_aud AUD_CLK_AUD_UART>, <&clock_aud AUD_SCLK_AUD_UART>; + clock-names = "uart", "clk_uart_baud0"; + status = "disabled"; + }; + + mmc_0: mmc at 12140000 { + compatible = "samsung,exynos5250-dw-mshc"; + reg = <0x12140000 0x2000>; + interrupts = <0 156 0>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clock_fsys FSYS_CLK_MMC0>, <&clock_top TOP_SCLK_MMC0>; + clock-names = "biu", "ciu"; + fifo-depth = <64>; + status = "disabled"; + }; + + mmc_1: mmc at 12150000 { + compatible = "samsung,exynos5250-dw-mshc"; + reg = <0x12150000 0x2000>; + interrupts = <0 158 0>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clock_fsys FSYS_CLK_MMC1>, <&clock_top TOP_SCLK_MMC1>; + clock-names = "biu", "ciu"; + fifo-depth = <64>; + status = "disabled"; + }; + + mmc_2: mmc at 12160000 { + compatible = "samsung,exynos5250-dw-mshc"; + reg = <0x12160000 0x2000>; + interrupts = <0 159 0>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clock_fsys FSYS_CLK_MMC2>, <&clock_top TOP_SCLK_MMC2>; + clock-names = "biu", "ciu"; + fifo-depth = <64>; + status = "disabled"; + }; + }; +}; + +#include "exynos5260-pinctrl.dtsi" -- 1.7.9.5 ^ permalink raw reply related [flat|nested] 20+ messages in thread
* Re: [PATCH v7 2/3] ARM: dts: add dts files for exynos5260 SoC 2014-04-03 10:00 ` Rahul Sharma @ 2014-04-09 10:29 ` Tomasz Figa -1 siblings, 0 replies; 20+ messages in thread From: Tomasz Figa @ 2014-04-09 10:29 UTC (permalink / raw) To: Rahul Sharma, linux-samsung-soc Cc: devicetree, linux-arm-kernel, kgene.kim, tomasz.figa, joshi, r.sh.open, Pankaj Dubey, Arun Kumar K Hi Rahul, On 03.04.2014 12:00, Rahul Sharma wrote: > The patch adds the dts files for exynos5260. > > Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com> > Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com> > Signed-off-by: Arun Kumar K <arun.kk@samsung.com> > Reviewed-by: Tomasz Figa <t.figa@samsung.com> > --- > arch/arm/boot/dts/exynos5260-pinctrl.dtsi | 574 +++++++++++++++++++++++++++++ > arch/arm/boot/dts/exynos5260.dtsi | 304 +++++++++++++++ > 2 files changed, 878 insertions(+) > create mode 100644 arch/arm/boot/dts/exynos5260-pinctrl.dtsi > create mode 100644 arch/arm/boot/dts/exynos5260.dtsi [snip] > diff --git a/arch/arm/boot/dts/exynos5260.dtsi b/arch/arm/boot/dts/exynos5260.dtsi > new file mode 100644 > index 0000000..188a2ac > --- /dev/null > +++ b/arch/arm/boot/dts/exynos5260.dtsi > @@ -0,0 +1,304 @@ > +/* > + * SAMSUNG EXYNOS5260 SoC device tree source > + * > + * Copyright (c) 2013 Samsung Electronics Co., Ltd. > + * http://www.samsung.com > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > +*/ > + > +#include "skeleton.dtsi" > + > +#include <dt-bindings/clock/exynos5260-clk.h> > + > +/ { > + compatible = "samsung,exynos5260"; Since Sachin's patches, "samsung,exynos5" compatible should be also added, before the more specific ones. Best regards, Tomasz ^ permalink raw reply [flat|nested] 20+ messages in thread
* [PATCH v7 2/3] ARM: dts: add dts files for exynos5260 SoC @ 2014-04-09 10:29 ` Tomasz Figa 0 siblings, 0 replies; 20+ messages in thread From: Tomasz Figa @ 2014-04-09 10:29 UTC (permalink / raw) To: linux-arm-kernel Hi Rahul, On 03.04.2014 12:00, Rahul Sharma wrote: > The patch adds the dts files for exynos5260. > > Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com> > Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com> > Signed-off-by: Arun Kumar K <arun.kk@samsung.com> > Reviewed-by: Tomasz Figa <t.figa@samsung.com> > --- > arch/arm/boot/dts/exynos5260-pinctrl.dtsi | 574 +++++++++++++++++++++++++++++ > arch/arm/boot/dts/exynos5260.dtsi | 304 +++++++++++++++ > 2 files changed, 878 insertions(+) > create mode 100644 arch/arm/boot/dts/exynos5260-pinctrl.dtsi > create mode 100644 arch/arm/boot/dts/exynos5260.dtsi [snip] > diff --git a/arch/arm/boot/dts/exynos5260.dtsi b/arch/arm/boot/dts/exynos5260.dtsi > new file mode 100644 > index 0000000..188a2ac > --- /dev/null > +++ b/arch/arm/boot/dts/exynos5260.dtsi > @@ -0,0 +1,304 @@ > +/* > + * SAMSUNG EXYNOS5260 SoC device tree source > + * > + * Copyright (c) 2013 Samsung Electronics Co., Ltd. > + * http://www.samsung.com > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > +*/ > + > +#include "skeleton.dtsi" > + > +#include <dt-bindings/clock/exynos5260-clk.h> > + > +/ { > + compatible = "samsung,exynos5260"; Since Sachin's patches, "samsung,exynos5" compatible should be also added, before the more specific ones. Best regards, Tomasz ^ permalink raw reply [flat|nested] 20+ messages in thread
* [PATCH v7 3/3] ARM: dts: add dts files for xyref5260 board 2014-04-03 10:00 ` Rahul Sharma @ 2014-04-03 10:00 ` Rahul Sharma -1 siblings, 0 replies; 20+ messages in thread From: Rahul Sharma @ 2014-04-03 10:00 UTC (permalink / raw) To: linux-samsung-soc Cc: devicetree, linux-arm-kernel, kgene.kim, tomasz.figa, joshi, r.sh.open, Rahul Sharma The patch adds the dts files for xyref5260 board which is based on Exynos5260 Evt0 sample. Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/exynos5260-xyref5260.dts | 103 ++++++++++++++++++++++++++++ 2 files changed, 104 insertions(+) create mode 100644 arch/arm/boot/dts/exynos5260-xyref5260.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index b9d6a8b..477723b 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -72,6 +72,7 @@ dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \ exynos5250-arndale.dtb \ exynos5250-smdk5250.dtb \ exynos5250-snow.dtb \ + exynos5260-xyref5260.dtb \ exynos5420-arndale-octa.dtb \ exynos5420-smdk5420.dtb \ exynos5440-sd5v1.dtb \ diff --git a/arch/arm/boot/dts/exynos5260-xyref5260.dts b/arch/arm/boot/dts/exynos5260-xyref5260.dts new file mode 100644 index 0000000..fb1b0ee --- /dev/null +++ b/arch/arm/boot/dts/exynos5260-xyref5260.dts @@ -0,0 +1,103 @@ +/* + * SAMSUNG XYREF5260 EVT0 board device tree source + * + * Copyright (c) 2013 Samsung Electronics Co., Ltd. + * http://www.samsung.com + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +/dts-v1/; +#include "exynos5260.dtsi" + +/ { + model = "SAMSUNG XYREF5260 EVT0 board based on EXYNOS5260"; + compatible = "samsung,xyref5260", "samsung,exynos5260"; + + memory { + reg = <0x20000000 0x80000000>; + }; + + chosen { + bootargs = "console=ttySAC2,115200"; + }; + + fin_pll: xxti { + compatible = "fixed-clock"; + clock-frequency = <24000000>; + clock-output-names = "fin_pll"; + #clock-cells = <0>; + }; + + xrtcxti: xrtcxti { + compatible = "fixed-clock"; + clock-frequency = <32768>; + clock-output-names = "xrtcxti"; + #clock-cells = <0>; + }; +}; + +&pinctrl_0 { + hdmi_hpd_irq: hdmi-hpd-irq { + samsung,pins = "gpx3-7"; + samsung,pin-function = <0>; + samsung,pin-pud = <1>; + samsung,pin-drv = <0>; + }; +}; + +&uart0 { + status = "okay"; +}; + +&uart1 { + status = "okay"; +}; + +&uart2 { + status = "okay"; +}; + +&uart3 { + status = "okay"; +}; + +&mmc_0 { + status = "okay"; + num-slots = <1>; + broken-cd; + bypass-smu; + supports-highspeed; + supports-hs200-mode; /* 200 Mhz */ + card-detect-delay = <200>; + samsung,dw-mshc-ciu-div = <3>; + samsung,dw-mshc-sdr-timing = <0 4>; + samsung,dw-mshc-ddr-timing = <0 2>; + pinctrl-names = "default"; + pinctrl-0 = <&sd0_rdqs &sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8>; + + slot@0 { + reg = <0>; + bus-width = <8>; + }; +}; + +&mmc_2 { + status = "okay"; + num-slots = <1>; + supports-highspeed; + card-detect-delay = <200>; + samsung,dw-mshc-ciu-div = <3>; + samsung,dw-mshc-sdr-timing = <2 3>; + samsung,dw-mshc-ddr-timing = <1 2>; + pinctrl-names = "default"; + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>; + + slot@0 { + reg = <0>; + bus-width = <4>; + disable-wp; + }; +}; -- 1.7.9.5 ^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v7 3/3] ARM: dts: add dts files for xyref5260 board @ 2014-04-03 10:00 ` Rahul Sharma 0 siblings, 0 replies; 20+ messages in thread From: Rahul Sharma @ 2014-04-03 10:00 UTC (permalink / raw) To: linux-arm-kernel The patch adds the dts files for xyref5260 board which is based on Exynos5260 Evt0 sample. Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/exynos5260-xyref5260.dts | 103 ++++++++++++++++++++++++++++ 2 files changed, 104 insertions(+) create mode 100644 arch/arm/boot/dts/exynos5260-xyref5260.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index b9d6a8b..477723b 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -72,6 +72,7 @@ dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \ exynos5250-arndale.dtb \ exynos5250-smdk5250.dtb \ exynos5250-snow.dtb \ + exynos5260-xyref5260.dtb \ exynos5420-arndale-octa.dtb \ exynos5420-smdk5420.dtb \ exynos5440-sd5v1.dtb \ diff --git a/arch/arm/boot/dts/exynos5260-xyref5260.dts b/arch/arm/boot/dts/exynos5260-xyref5260.dts new file mode 100644 index 0000000..fb1b0ee --- /dev/null +++ b/arch/arm/boot/dts/exynos5260-xyref5260.dts @@ -0,0 +1,103 @@ +/* + * SAMSUNG XYREF5260 EVT0 board device tree source + * + * Copyright (c) 2013 Samsung Electronics Co., Ltd. + * http://www.samsung.com + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +/dts-v1/; +#include "exynos5260.dtsi" + +/ { + model = "SAMSUNG XYREF5260 EVT0 board based on EXYNOS5260"; + compatible = "samsung,xyref5260", "samsung,exynos5260"; + + memory { + reg = <0x20000000 0x80000000>; + }; + + chosen { + bootargs = "console=ttySAC2,115200"; + }; + + fin_pll: xxti { + compatible = "fixed-clock"; + clock-frequency = <24000000>; + clock-output-names = "fin_pll"; + #clock-cells = <0>; + }; + + xrtcxti: xrtcxti { + compatible = "fixed-clock"; + clock-frequency = <32768>; + clock-output-names = "xrtcxti"; + #clock-cells = <0>; + }; +}; + +&pinctrl_0 { + hdmi_hpd_irq: hdmi-hpd-irq { + samsung,pins = "gpx3-7"; + samsung,pin-function = <0>; + samsung,pin-pud = <1>; + samsung,pin-drv = <0>; + }; +}; + +&uart0 { + status = "okay"; +}; + +&uart1 { + status = "okay"; +}; + +&uart2 { + status = "okay"; +}; + +&uart3 { + status = "okay"; +}; + +&mmc_0 { + status = "okay"; + num-slots = <1>; + broken-cd; + bypass-smu; + supports-highspeed; + supports-hs200-mode; /* 200 Mhz */ + card-detect-delay = <200>; + samsung,dw-mshc-ciu-div = <3>; + samsung,dw-mshc-sdr-timing = <0 4>; + samsung,dw-mshc-ddr-timing = <0 2>; + pinctrl-names = "default"; + pinctrl-0 = <&sd0_rdqs &sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8>; + + slot at 0 { + reg = <0>; + bus-width = <8>; + }; +}; + +&mmc_2 { + status = "okay"; + num-slots = <1>; + supports-highspeed; + card-detect-delay = <200>; + samsung,dw-mshc-ciu-div = <3>; + samsung,dw-mshc-sdr-timing = <2 3>; + samsung,dw-mshc-ddr-timing = <1 2>; + pinctrl-names = "default"; + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>; + + slot at 0 { + reg = <0>; + bus-width = <4>; + disable-wp; + }; +}; -- 1.7.9.5 ^ permalink raw reply related [flat|nested] 20+ messages in thread
* Re: [PATCH v7 3/3] ARM: dts: add dts files for xyref5260 board 2014-04-03 10:00 ` Rahul Sharma @ 2014-04-07 8:40 ` Sachin Kamat -1 siblings, 0 replies; 20+ messages in thread From: Sachin Kamat @ 2014-04-07 8:40 UTC (permalink / raw) To: Rahul Sharma Cc: linux-samsung-soc, devicetree, linux-arm-kernel, Kukjin Kim, Tomasz Figa, sunil joshi, Rahul Sharma On 3 April 2014 15:30, Rahul Sharma <rahul.sharma@samsung.com> wrote: > The patch adds the dts files for xyref5260 board which > is based on Exynos5260 Evt0 sample. > > Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com> > --- > +/ { > + model = "SAMSUNG XYREF5260 EVT0 board based on EXYNOS5260"; > + compatible = "samsung,xyref5260", "samsung,exynos5260"; "samsung,exynos5260" is OK here for future compatibility (if soc specific quirk is required). Please also add "samsung,exynos5" to compatible list. -- With warm regards, Sachin ^ permalink raw reply [flat|nested] 20+ messages in thread
* [PATCH v7 3/3] ARM: dts: add dts files for xyref5260 board @ 2014-04-07 8:40 ` Sachin Kamat 0 siblings, 0 replies; 20+ messages in thread From: Sachin Kamat @ 2014-04-07 8:40 UTC (permalink / raw) To: linux-arm-kernel On 3 April 2014 15:30, Rahul Sharma <rahul.sharma@samsung.com> wrote: > The patch adds the dts files for xyref5260 board which > is based on Exynos5260 Evt0 sample. > > Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com> > --- > +/ { > + model = "SAMSUNG XYREF5260 EVT0 board based on EXYNOS5260"; > + compatible = "samsung,xyref5260", "samsung,exynos5260"; "samsung,exynos5260" is OK here for future compatibility (if soc specific quirk is required). Please also add "samsung,exynos5" to compatible list. -- With warm regards, Sachin ^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH v7 3/3] ARM: dts: add dts files for xyref5260 board 2014-04-07 8:40 ` Sachin Kamat @ 2014-04-09 10:52 ` Tomasz Figa -1 siblings, 0 replies; 20+ messages in thread From: Tomasz Figa @ 2014-04-09 10:52 UTC (permalink / raw) To: Sachin Kamat, Rahul Sharma Cc: linux-samsung-soc, devicetree, linux-arm-kernel, Kukjin Kim, Tomasz Figa, sunil joshi, Rahul Sharma On 07.04.2014 10:40, Sachin Kamat wrote: > On 3 April 2014 15:30, Rahul Sharma <rahul.sharma@samsung.com> wrote: >> The patch adds the dts files for xyref5260 board which >> is based on Exynos5260 Evt0 sample. >> >> Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com> >> --- > >> +/ { >> + model = "SAMSUNG XYREF5260 EVT0 board based on EXYNOS5260"; >> + compatible = "samsung,xyref5260", "samsung,exynos5260"; > > "samsung,exynos5260" is OK here for future compatibility (if soc > specific quirk is required). > Please also add "samsung,exynos5" to compatible list. > Right. SoC family compatible string should be added between board and SoC model strings. Best regards, Tomasz ^ permalink raw reply [flat|nested] 20+ messages in thread
* [PATCH v7 3/3] ARM: dts: add dts files for xyref5260 board @ 2014-04-09 10:52 ` Tomasz Figa 0 siblings, 0 replies; 20+ messages in thread From: Tomasz Figa @ 2014-04-09 10:52 UTC (permalink / raw) To: linux-arm-kernel On 07.04.2014 10:40, Sachin Kamat wrote: > On 3 April 2014 15:30, Rahul Sharma <rahul.sharma@samsung.com> wrote: >> The patch adds the dts files for xyref5260 board which >> is based on Exynos5260 Evt0 sample. >> >> Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com> >> --- > >> +/ { >> + model = "SAMSUNG XYREF5260 EVT0 board based on EXYNOS5260"; >> + compatible = "samsung,xyref5260", "samsung,exynos5260"; > > "samsung,exynos5260" is OK here for future compatibility (if soc > specific quirk is required). > Please also add "samsung,exynos5" to compatible list. > Right. SoC family compatible string should be added between board and SoC model strings. Best regards, Tomasz ^ permalink raw reply [flat|nested] 20+ messages in thread
end of thread, other threads:[~2014-04-09 10:52 UTC | newest]
Thread overview: 20+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2014-04-03 10:00 [PATCH v7 0/3] exynos: arch: add support for exynos5260 SoC Rahul Sharma
2014-04-03 10:00 ` Rahul Sharma
[not found] ` <1396519224-18712-1-git-send-email-rahul.sharma-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
2014-04-03 10:00 ` [PATCH v7 1/3] ARM: EXYNOS: initial board " Rahul Sharma
2014-04-03 10:00 ` Rahul Sharma
2014-04-07 8:38 ` Sachin Kamat
2014-04-07 8:38 ` Sachin Kamat
2014-04-09 9:04 ` Tomasz Figa
2014-04-09 9:04 ` Tomasz Figa
2014-04-09 9:15 ` Rahul Sharma
2014-04-09 9:15 ` Rahul Sharma
2014-04-03 10:00 ` [PATCH v7 2/3] ARM: dts: add dts files " Rahul Sharma
2014-04-03 10:00 ` Rahul Sharma
2014-04-09 10:29 ` Tomasz Figa
2014-04-09 10:29 ` Tomasz Figa
2014-04-03 10:00 ` [PATCH v7 3/3] ARM: dts: add dts files for xyref5260 board Rahul Sharma
2014-04-03 10:00 ` Rahul Sharma
2014-04-07 8:40 ` Sachin Kamat
2014-04-07 8:40 ` Sachin Kamat
2014-04-09 10:52 ` Tomasz Figa
2014-04-09 10:52 ` Tomasz Figa
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.