* [PATCH v3 0/4] ARM: dts: use syscon property instead of ctrl-module
@ 2015-12-15 9:39 ` Kishon Vijay Abraham I
0 siblings, 0 replies; 24+ messages in thread
From: Kishon Vijay Abraham I @ 2015-12-15 9:39 UTC (permalink / raw)
To: devicetree, linux-kernel, linux-omap, tony
Cc: bcousson, kishon, robh+dt, pawel.moll, mark.rutland,
ijc+devicetree, galak, linux, rogerq, nsekhar, linux-arm-kernel,
linux-pci, linux-usb, t-kristo
This series is basically to deprecate using ctrl-module property and use
corresponding syscon properties to program the control module registers.
Changes from v2:
No changes.
Changes from v1:
*) Squashed the patches that replaces "ctrl-module" with
"syscon-phy-power"
*) Added "syscon-phy-power" for SATA dt node in OMAP5 which was missed
earlier
*) removed _ARM: dts: omap4: Use "syscon-otghs" instead of "ctrl-module"
in USB node_. It will be done later.
Changes from [1] in PHY patches include
*) cleanup ti_pipe3_probe
*) have mask, power_on and power_off values in usb_phy_data for
omap-usb2 phy
This series should be merged only after [2]
[2] -> http://www.spinics.net/lists/kernel/msg2144510.html
Logs with SYSCON DT
DRA72 EVM : http://pastebin.ubuntu.com/14025205/
DRA7 EVM : http://pastebin.ubuntu.com/14025212/
AM43XX EVM: http://pastebin.ubuntu.com/14025222/
OMAP5 UEVM: http://pastebin.ubuntu.com/14025228/
Logs without SYSCON DT
DRA72 EVM : http://pastebin.ubuntu.com/14025233/
DRA7 EVM : http://pastebin.ubuntu.com/14025238/
AM43XX EVM: http://pastebin.ubuntu.com/14025329/
OMAP5 UEVM: http://pastebin.ubuntu.com/14025248/
The config I used: http://pastebin.ubuntu.com/14025336/
Kishon Vijay Abraham I (4):
ARM: dts: dra7: Add dt node for the sycon pcie
ARM: dts: dra7: Use "syscon-phy-power" and "syscon-pcs" in PCIe PHY
node
ARM: dts: dra7: Use "ti,dra7x-usb2-phy2" compatible string for USB2
PHY2
ARM: dts: <am4372/dra7/omap5>: Use "syscon-phy-power" instead of
"ctrl-module"
arch/arm/boot/dts/am4372.dtsi | 16 ++-------
arch/arm/boot/dts/dra7.dtsi | 75 ++++++++++++-----------------------------
arch/arm/boot/dts/omap5.dtsi | 26 ++------------
3 files changed, 26 insertions(+), 91 deletions(-)
--
1.7.9.5
^ permalink raw reply [flat|nested] 24+ messages in thread
* [PATCH v3 0/4] ARM: dts: use syscon property instead of ctrl-module
@ 2015-12-15 9:39 ` Kishon Vijay Abraham I
0 siblings, 0 replies; 24+ messages in thread
From: Kishon Vijay Abraham I @ 2015-12-15 9:39 UTC (permalink / raw)
To: devicetree, linux-kernel, linux-omap, tony
Cc: bcousson, kishon, robh+dt, pawel.moll, mark.rutland,
ijc+devicetree, galak, linux, rogerq, nsekhar, linux-arm-kernel,
linux-pci, linux-usb, t-kristo
This series is basically to deprecate using ctrl-module property and use
corresponding syscon properties to program the control module registers.
Changes from v2:
No changes.
Changes from v1:
*) Squashed the patches that replaces "ctrl-module" with
"syscon-phy-power"
*) Added "syscon-phy-power" for SATA dt node in OMAP5 which was missed
earlier
*) removed _ARM: dts: omap4: Use "syscon-otghs" instead of "ctrl-module"
in USB node_. It will be done later.
Changes from [1] in PHY patches include
*) cleanup ti_pipe3_probe
*) have mask, power_on and power_off values in usb_phy_data for
omap-usb2 phy
This series should be merged only after [2]
[2] -> http://www.spinics.net/lists/kernel/msg2144510.html
Logs with SYSCON DT
DRA72 EVM : http://pastebin.ubuntu.com/14025205/
DRA7 EVM : http://pastebin.ubuntu.com/14025212/
AM43XX EVM: http://pastebin.ubuntu.com/14025222/
OMAP5 UEVM: http://pastebin.ubuntu.com/14025228/
Logs without SYSCON DT
DRA72 EVM : http://pastebin.ubuntu.com/14025233/
DRA7 EVM : http://pastebin.ubuntu.com/14025238/
AM43XX EVM: http://pastebin.ubuntu.com/14025329/
OMAP5 UEVM: http://pastebin.ubuntu.com/14025248/
The config I used: http://pastebin.ubuntu.com/14025336/
Kishon Vijay Abraham I (4):
ARM: dts: dra7: Add dt node for the sycon pcie
ARM: dts: dra7: Use "syscon-phy-power" and "syscon-pcs" in PCIe PHY
node
ARM: dts: dra7: Use "ti,dra7x-usb2-phy2" compatible string for USB2
PHY2
ARM: dts: <am4372/dra7/omap5>: Use "syscon-phy-power" instead of
"ctrl-module"
arch/arm/boot/dts/am4372.dtsi | 16 ++-------
arch/arm/boot/dts/dra7.dtsi | 75 ++++++++++++-----------------------------
arch/arm/boot/dts/omap5.dtsi | 26 ++------------
3 files changed, 26 insertions(+), 91 deletions(-)
--
1.7.9.5
^ permalink raw reply [flat|nested] 24+ messages in thread
* [PATCH v3 0/4] ARM: dts: use syscon property instead of ctrl-module
@ 2015-12-15 9:39 ` Kishon Vijay Abraham I
0 siblings, 0 replies; 24+ messages in thread
From: Kishon Vijay Abraham I @ 2015-12-15 9:39 UTC (permalink / raw)
To: linux-arm-kernel
This series is basically to deprecate using ctrl-module property and use
corresponding syscon properties to program the control module registers.
Changes from v2:
No changes.
Changes from v1:
*) Squashed the patches that replaces "ctrl-module" with
"syscon-phy-power"
*) Added "syscon-phy-power" for SATA dt node in OMAP5 which was missed
earlier
*) removed _ARM: dts: omap4: Use "syscon-otghs" instead of "ctrl-module"
in USB node_. It will be done later.
Changes from [1] in PHY patches include
*) cleanup ti_pipe3_probe
*) have mask, power_on and power_off values in usb_phy_data for
omap-usb2 phy
This series should be merged only after [2]
[2] -> http://www.spinics.net/lists/kernel/msg2144510.html
Logs with SYSCON DT
DRA72 EVM : http://pastebin.ubuntu.com/14025205/
DRA7 EVM : http://pastebin.ubuntu.com/14025212/
AM43XX EVM: http://pastebin.ubuntu.com/14025222/
OMAP5 UEVM: http://pastebin.ubuntu.com/14025228/
Logs without SYSCON DT
DRA72 EVM : http://pastebin.ubuntu.com/14025233/
DRA7 EVM : http://pastebin.ubuntu.com/14025238/
AM43XX EVM: http://pastebin.ubuntu.com/14025329/
OMAP5 UEVM: http://pastebin.ubuntu.com/14025248/
The config I used: http://pastebin.ubuntu.com/14025336/
Kishon Vijay Abraham I (4):
ARM: dts: dra7: Add dt node for the sycon pcie
ARM: dts: dra7: Use "syscon-phy-power" and "syscon-pcs" in PCIe PHY
node
ARM: dts: dra7: Use "ti,dra7x-usb2-phy2" compatible string for USB2
PHY2
ARM: dts: <am4372/dra7/omap5>: Use "syscon-phy-power" instead of
"ctrl-module"
arch/arm/boot/dts/am4372.dtsi | 16 ++-------
arch/arm/boot/dts/dra7.dtsi | 75 ++++++++++++-----------------------------
arch/arm/boot/dts/omap5.dtsi | 26 ++------------
3 files changed, 26 insertions(+), 91 deletions(-)
--
1.7.9.5
^ permalink raw reply [flat|nested] 24+ messages in thread
* [PATCH v3 1/4] ARM: dts: dra7: Add dt node for the sycon pcie
@ 2015-12-15 9:39 ` Kishon Vijay Abraham I
0 siblings, 0 replies; 24+ messages in thread
From: Kishon Vijay Abraham I @ 2015-12-15 9:39 UTC (permalink / raw)
To: devicetree, linux-kernel, linux-omap, tony
Cc: bcousson, kishon, robh+dt, pawel.moll, mark.rutland,
ijc+devicetree, galak, linux, rogerq, nsekhar, linux-arm-kernel,
linux-pci, linux-usb, t-kristo
Add new device tree node for the control module register space where
PCIe registers are present.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
arch/arm/boot/dts/dra7.dtsi | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
index fe99231..e38f63f 100644
--- a/arch/arm/boot/dts/dra7.dtsi
+++ b/arch/arm/boot/dts/dra7.dtsi
@@ -155,6 +155,11 @@
compatible = "syscon";
reg = <0x1c04 0x0020>;
};
+
+ scm_conf_pcie: tisyscon@1c24 {
+ compatible = "syscon";
+ reg = <0x1c24 0x0024>;
+ };
};
cm_core_aon: cm_core_aon@5000 {
--
1.7.9.5
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v3 1/4] ARM: dts: dra7: Add dt node for the sycon pcie
@ 2015-12-15 9:39 ` Kishon Vijay Abraham I
0 siblings, 0 replies; 24+ messages in thread
From: Kishon Vijay Abraham I @ 2015-12-15 9:39 UTC (permalink / raw)
To: devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-omap-u79uwXL29TY76Z2rM5mHXA, tony-4v6yS6AI5VpBDgjK7y7TUQ
Cc: bcousson-rdvid1DuHRBWk0Htik3J/w, kishon-l0cyMroinI0,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A, pawel.moll-5wv7dgnIgG8,
mark.rutland-5wv7dgnIgG8, ijc+devicetree-KcIKpvwj1kUDXYZnReoRVg,
galak-sgV2jX0FEOL9JmXXK+q4OQ, linux-lFZ/pmaqli7XmaaqVzeoHQ,
rogerq-l0cyMroinI0, nsekhar-l0cyMroinI0,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-pci-u79uwXL29TY76Z2rM5mHXA,
linux-usb-u79uwXL29TY76Z2rM5mHXA, t-kristo-l0cyMroinI0
Add new device tree node for the control module register space where
PCIe registers are present.
Signed-off-by: Kishon Vijay Abraham I <kishon-l0cyMroinI0@public.gmane.org>
---
arch/arm/boot/dts/dra7.dtsi | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
index fe99231..e38f63f 100644
--- a/arch/arm/boot/dts/dra7.dtsi
+++ b/arch/arm/boot/dts/dra7.dtsi
@@ -155,6 +155,11 @@
compatible = "syscon";
reg = <0x1c04 0x0020>;
};
+
+ scm_conf_pcie: tisyscon@1c24 {
+ compatible = "syscon";
+ reg = <0x1c24 0x0024>;
+ };
};
cm_core_aon: cm_core_aon@5000 {
--
1.7.9.5
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v3 1/4] ARM: dts: dra7: Add dt node for the sycon pcie
@ 2015-12-15 9:39 ` Kishon Vijay Abraham I
0 siblings, 0 replies; 24+ messages in thread
From: Kishon Vijay Abraham I @ 2015-12-15 9:39 UTC (permalink / raw)
To: linux-arm-kernel
Add new device tree node for the control module register space where
PCIe registers are present.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
arch/arm/boot/dts/dra7.dtsi | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
index fe99231..e38f63f 100644
--- a/arch/arm/boot/dts/dra7.dtsi
+++ b/arch/arm/boot/dts/dra7.dtsi
@@ -155,6 +155,11 @@
compatible = "syscon";
reg = <0x1c04 0x0020>;
};
+
+ scm_conf_pcie: tisyscon at 1c24 {
+ compatible = "syscon";
+ reg = <0x1c24 0x0024>;
+ };
};
cm_core_aon: cm_core_aon at 5000 {
--
1.7.9.5
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v3 2/4] ARM: dts: dra7: Use "syscon-phy-power" and "syscon-pcs" in PCIe PHY node
2015-12-15 9:39 ` Kishon Vijay Abraham I
(?)
@ 2015-12-15 9:39 ` Kishon Vijay Abraham I
-1 siblings, 0 replies; 24+ messages in thread
From: Kishon Vijay Abraham I @ 2015-12-15 9:39 UTC (permalink / raw)
To: devicetree, linux-kernel, linux-omap, tony
Cc: bcousson, kishon, robh+dt, pawel.moll, mark.rutland,
ijc+devicetree, galak, linux, rogerq, nsekhar, linux-arm-kernel,
linux-pci, linux-usb, t-kristo
Add "syscon-phy-power" property and "syscon-pcs" property which can
be used to perform the control module initializations and remove
the deprecated "ctrl-module" property from PCIe PHY dt nodes.
Phandle to "sysclk" clock node is also added to the PCIe PHY node
since some of the syscon initializations is based on system clock
frequency.
Since "omap_control_pcie1phy" and "omap_control_pcie2phy" devicetree
nodes are no longer used, remove it.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
arch/arm/boot/dts/dra7.dtsi | 33 ++++++++++-----------------------
1 file changed, 10 insertions(+), 23 deletions(-)
diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
index e38f63f..156d735 100644
--- a/arch/arm/boot/dts/dra7.dtsi
+++ b/arch/arm/boot/dts/dra7.dtsi
@@ -1204,16 +1204,18 @@
reg = <0x4a094000 0x80>, /* phy_rx */
<0x4a094400 0x64>; /* phy_tx */
reg-names = "phy_rx", "phy_tx";
- ctrl-module = <&omap_control_pcie1phy>;
+ syscon-phy-power = <&scm_conf_pcie 0x1c>;
+ syscon-pcs = <&scm_conf_pcie 0x10>;
clocks = <&dpll_pcie_ref_ck>,
<&dpll_pcie_ref_m2ldo_ck>,
<&optfclk_pciephy1_32khz>,
<&optfclk_pciephy1_clk>,
<&optfclk_pciephy1_div_clk>,
- <&optfclk_pciephy_div>;
+ <&optfclk_pciephy_div>,
+ <&sys_clkin1>;
clock-names = "dpll_ref", "dpll_ref_m2",
"wkupclk", "refclk",
- "div-clk", "phy-div";
+ "div-clk", "phy-div", "sysclk";
#phy-cells = <0>;
};
@@ -1222,16 +1224,18 @@
reg = <0x4a095000 0x80>, /* phy_rx */
<0x4a095400 0x64>; /* phy_tx */
reg-names = "phy_rx", "phy_tx";
- ctrl-module = <&omap_control_pcie2phy>;
+ syscon-phy-power = <&scm_conf_pcie 0x20>;
+ syscon-pcs = <&scm_conf_pcie 0x10>;
clocks = <&dpll_pcie_ref_ck>,
<&dpll_pcie_ref_m2ldo_ck>,
<&optfclk_pciephy2_32khz>,
<&optfclk_pciephy2_clk>,
<&optfclk_pciephy2_div_clk>,
- <&optfclk_pciephy_div>;
+ <&optfclk_pciephy_div>,
+ <&sys_clkin1>;
clock-names = "dpll_ref", "dpll_ref_m2",
"wkupclk", "refclk",
- "div-clk", "phy-div";
+ "div-clk", "phy-div", "sysclk";
#phy-cells = <0>;
status = "disabled";
};
@@ -1247,23 +1251,6 @@
ti,hwmods = "sata";
};
- omap_control_pcie1phy: control-phy@0x4a003c40 {
- compatible = "ti,control-phy-pcie";
- reg = <0x4a003c40 0x4>, <0x4a003c14 0x4>, <0x4a003c34 0x4>;
- reg-names = "power", "control_sma", "pcie_pcs";
- clocks = <&sys_clkin1>;
- clock-names = "sysclk";
- };
-
- omap_control_pcie2phy: control-pcie@0x4a003c44 {
- compatible = "ti,control-phy-pcie";
- reg = <0x4a003c44 0x4>, <0x4a003c14 0x4>, <0x4a003c34 0x4>;
- reg-names = "power", "control_sma", "pcie_pcs";
- clocks = <&sys_clkin1>;
- clock-names = "sysclk";
- status = "disabled";
- };
-
rtc: rtc@48838000 {
compatible = "ti,am3352-rtc";
reg = <0x48838000 0x100>;
--
1.7.9.5
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v3 2/4] ARM: dts: dra7: Use "syscon-phy-power" and "syscon-pcs" in PCIe PHY node
@ 2015-12-15 9:39 ` Kishon Vijay Abraham I
0 siblings, 0 replies; 24+ messages in thread
From: Kishon Vijay Abraham I @ 2015-12-15 9:39 UTC (permalink / raw)
To: devicetree, linux-kernel, linux-omap, tony
Cc: mark.rutland, linux, pawel.moll, ijc+devicetree, linux-pci,
linux-usb, nsekhar, kishon, t-kristo, robh+dt, bcousson, galak,
linux-arm-kernel, rogerq
Add "syscon-phy-power" property and "syscon-pcs" property which can
be used to perform the control module initializations and remove
the deprecated "ctrl-module" property from PCIe PHY dt nodes.
Phandle to "sysclk" clock node is also added to the PCIe PHY node
since some of the syscon initializations is based on system clock
frequency.
Since "omap_control_pcie1phy" and "omap_control_pcie2phy" devicetree
nodes are no longer used, remove it.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
arch/arm/boot/dts/dra7.dtsi | 33 ++++++++++-----------------------
1 file changed, 10 insertions(+), 23 deletions(-)
diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
index e38f63f..156d735 100644
--- a/arch/arm/boot/dts/dra7.dtsi
+++ b/arch/arm/boot/dts/dra7.dtsi
@@ -1204,16 +1204,18 @@
reg = <0x4a094000 0x80>, /* phy_rx */
<0x4a094400 0x64>; /* phy_tx */
reg-names = "phy_rx", "phy_tx";
- ctrl-module = <&omap_control_pcie1phy>;
+ syscon-phy-power = <&scm_conf_pcie 0x1c>;
+ syscon-pcs = <&scm_conf_pcie 0x10>;
clocks = <&dpll_pcie_ref_ck>,
<&dpll_pcie_ref_m2ldo_ck>,
<&optfclk_pciephy1_32khz>,
<&optfclk_pciephy1_clk>,
<&optfclk_pciephy1_div_clk>,
- <&optfclk_pciephy_div>;
+ <&optfclk_pciephy_div>,
+ <&sys_clkin1>;
clock-names = "dpll_ref", "dpll_ref_m2",
"wkupclk", "refclk",
- "div-clk", "phy-div";
+ "div-clk", "phy-div", "sysclk";
#phy-cells = <0>;
};
@@ -1222,16 +1224,18 @@
reg = <0x4a095000 0x80>, /* phy_rx */
<0x4a095400 0x64>; /* phy_tx */
reg-names = "phy_rx", "phy_tx";
- ctrl-module = <&omap_control_pcie2phy>;
+ syscon-phy-power = <&scm_conf_pcie 0x20>;
+ syscon-pcs = <&scm_conf_pcie 0x10>;
clocks = <&dpll_pcie_ref_ck>,
<&dpll_pcie_ref_m2ldo_ck>,
<&optfclk_pciephy2_32khz>,
<&optfclk_pciephy2_clk>,
<&optfclk_pciephy2_div_clk>,
- <&optfclk_pciephy_div>;
+ <&optfclk_pciephy_div>,
+ <&sys_clkin1>;
clock-names = "dpll_ref", "dpll_ref_m2",
"wkupclk", "refclk",
- "div-clk", "phy-div";
+ "div-clk", "phy-div", "sysclk";
#phy-cells = <0>;
status = "disabled";
};
@@ -1247,23 +1251,6 @@
ti,hwmods = "sata";
};
- omap_control_pcie1phy: control-phy@0x4a003c40 {
- compatible = "ti,control-phy-pcie";
- reg = <0x4a003c40 0x4>, <0x4a003c14 0x4>, <0x4a003c34 0x4>;
- reg-names = "power", "control_sma", "pcie_pcs";
- clocks = <&sys_clkin1>;
- clock-names = "sysclk";
- };
-
- omap_control_pcie2phy: control-pcie@0x4a003c44 {
- compatible = "ti,control-phy-pcie";
- reg = <0x4a003c44 0x4>, <0x4a003c14 0x4>, <0x4a003c34 0x4>;
- reg-names = "power", "control_sma", "pcie_pcs";
- clocks = <&sys_clkin1>;
- clock-names = "sysclk";
- status = "disabled";
- };
-
rtc: rtc@48838000 {
compatible = "ti,am3352-rtc";
reg = <0x48838000 0x100>;
--
1.7.9.5
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v3 2/4] ARM: dts: dra7: Use "syscon-phy-power" and "syscon-pcs" in PCIe PHY node
@ 2015-12-15 9:39 ` Kishon Vijay Abraham I
0 siblings, 0 replies; 24+ messages in thread
From: Kishon Vijay Abraham I @ 2015-12-15 9:39 UTC (permalink / raw)
To: linux-arm-kernel
Add "syscon-phy-power" property and "syscon-pcs" property which can
be used to perform the control module initializations and remove
the deprecated "ctrl-module" property from PCIe PHY dt nodes.
Phandle to "sysclk" clock node is also added to the PCIe PHY node
since some of the syscon initializations is based on system clock
frequency.
Since "omap_control_pcie1phy" and "omap_control_pcie2phy" devicetree
nodes are no longer used, remove it.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
arch/arm/boot/dts/dra7.dtsi | 33 ++++++++++-----------------------
1 file changed, 10 insertions(+), 23 deletions(-)
diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
index e38f63f..156d735 100644
--- a/arch/arm/boot/dts/dra7.dtsi
+++ b/arch/arm/boot/dts/dra7.dtsi
@@ -1204,16 +1204,18 @@
reg = <0x4a094000 0x80>, /* phy_rx */
<0x4a094400 0x64>; /* phy_tx */
reg-names = "phy_rx", "phy_tx";
- ctrl-module = <&omap_control_pcie1phy>;
+ syscon-phy-power = <&scm_conf_pcie 0x1c>;
+ syscon-pcs = <&scm_conf_pcie 0x10>;
clocks = <&dpll_pcie_ref_ck>,
<&dpll_pcie_ref_m2ldo_ck>,
<&optfclk_pciephy1_32khz>,
<&optfclk_pciephy1_clk>,
<&optfclk_pciephy1_div_clk>,
- <&optfclk_pciephy_div>;
+ <&optfclk_pciephy_div>,
+ <&sys_clkin1>;
clock-names = "dpll_ref", "dpll_ref_m2",
"wkupclk", "refclk",
- "div-clk", "phy-div";
+ "div-clk", "phy-div", "sysclk";
#phy-cells = <0>;
};
@@ -1222,16 +1224,18 @@
reg = <0x4a095000 0x80>, /* phy_rx */
<0x4a095400 0x64>; /* phy_tx */
reg-names = "phy_rx", "phy_tx";
- ctrl-module = <&omap_control_pcie2phy>;
+ syscon-phy-power = <&scm_conf_pcie 0x20>;
+ syscon-pcs = <&scm_conf_pcie 0x10>;
clocks = <&dpll_pcie_ref_ck>,
<&dpll_pcie_ref_m2ldo_ck>,
<&optfclk_pciephy2_32khz>,
<&optfclk_pciephy2_clk>,
<&optfclk_pciephy2_div_clk>,
- <&optfclk_pciephy_div>;
+ <&optfclk_pciephy_div>,
+ <&sys_clkin1>;
clock-names = "dpll_ref", "dpll_ref_m2",
"wkupclk", "refclk",
- "div-clk", "phy-div";
+ "div-clk", "phy-div", "sysclk";
#phy-cells = <0>;
status = "disabled";
};
@@ -1247,23 +1251,6 @@
ti,hwmods = "sata";
};
- omap_control_pcie1phy: control-phy at 0x4a003c40 {
- compatible = "ti,control-phy-pcie";
- reg = <0x4a003c40 0x4>, <0x4a003c14 0x4>, <0x4a003c34 0x4>;
- reg-names = "power", "control_sma", "pcie_pcs";
- clocks = <&sys_clkin1>;
- clock-names = "sysclk";
- };
-
- omap_control_pcie2phy: control-pcie at 0x4a003c44 {
- compatible = "ti,control-phy-pcie";
- reg = <0x4a003c44 0x4>, <0x4a003c14 0x4>, <0x4a003c34 0x4>;
- reg-names = "power", "control_sma", "pcie_pcs";
- clocks = <&sys_clkin1>;
- clock-names = "sysclk";
- status = "disabled";
- };
-
rtc: rtc at 48838000 {
compatible = "ti,am3352-rtc";
reg = <0x48838000 0x100>;
--
1.7.9.5
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v3 3/4] ARM: dts: dra7: Use "ti,dra7x-usb2-phy2" compatible string for USB2 PHY2
2015-12-15 9:39 ` Kishon Vijay Abraham I
(?)
@ 2015-12-15 9:39 ` Kishon Vijay Abraham I
-1 siblings, 0 replies; 24+ messages in thread
From: Kishon Vijay Abraham I @ 2015-12-15 9:39 UTC (permalink / raw)
To: devicetree, linux-kernel, linux-omap, tony
Cc: bcousson, kishon, robh+dt, pawel.moll, mark.rutland,
ijc+devicetree, galak, linux, rogerq, nsekhar, linux-arm-kernel,
linux-pci, linux-usb, t-kristo
The USB2 PHY2 has a different register map compared to USB2 PHY1
to power on/off the PHY. In order to handle it, use the new compatible
string "ti,dra7x-usb2-phy2" for the second instance of USB2 PHY.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
arch/arm/boot/dts/dra7.dtsi | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
index 156d735..41545f9 100644
--- a/arch/arm/boot/dts/dra7.dtsi
+++ b/arch/arm/boot/dts/dra7.dtsi
@@ -1299,7 +1299,8 @@
};
usb2_phy2: phy@4a085000 {
- compatible = "ti,omap-usb2";
+ compatible = "ti,dra7x-usb2-phy2",
+ "ti,omap-usb2";
reg = <0x4a085000 0x400>;
ctrl-module = <&omap_control_usb2phy2>;
clocks = <&usb_phy2_always_on_clk32k>,
--
1.7.9.5
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v3 3/4] ARM: dts: dra7: Use "ti,dra7x-usb2-phy2" compatible string for USB2 PHY2
@ 2015-12-15 9:39 ` Kishon Vijay Abraham I
0 siblings, 0 replies; 24+ messages in thread
From: Kishon Vijay Abraham I @ 2015-12-15 9:39 UTC (permalink / raw)
To: devicetree, linux-kernel, linux-omap, tony
Cc: bcousson, kishon, robh+dt, pawel.moll, mark.rutland,
ijc+devicetree, galak, linux, rogerq, nsekhar, linux-arm-kernel,
linux-pci, linux-usb, t-kristo
The USB2 PHY2 has a different register map compared to USB2 PHY1
to power on/off the PHY. In order to handle it, use the new compatible
string "ti,dra7x-usb2-phy2" for the second instance of USB2 PHY.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
arch/arm/boot/dts/dra7.dtsi | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
index 156d735..41545f9 100644
--- a/arch/arm/boot/dts/dra7.dtsi
+++ b/arch/arm/boot/dts/dra7.dtsi
@@ -1299,7 +1299,8 @@
};
usb2_phy2: phy@4a085000 {
- compatible = "ti,omap-usb2";
+ compatible = "ti,dra7x-usb2-phy2",
+ "ti,omap-usb2";
reg = <0x4a085000 0x400>;
ctrl-module = <&omap_control_usb2phy2>;
clocks = <&usb_phy2_always_on_clk32k>,
--
1.7.9.5
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v3 3/4] ARM: dts: dra7: Use "ti, dra7x-usb2-phy2" compatible string for USB2 PHY2
@ 2015-12-15 9:39 ` Kishon Vijay Abraham I
0 siblings, 0 replies; 24+ messages in thread
From: Kishon Vijay Abraham I @ 2015-12-15 9:39 UTC (permalink / raw)
To: linux-arm-kernel
The USB2 PHY2 has a different register map compared to USB2 PHY1
to power on/off the PHY. In order to handle it, use the new compatible
string "ti,dra7x-usb2-phy2" for the second instance of USB2 PHY.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
arch/arm/boot/dts/dra7.dtsi | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
index 156d735..41545f9 100644
--- a/arch/arm/boot/dts/dra7.dtsi
+++ b/arch/arm/boot/dts/dra7.dtsi
@@ -1299,7 +1299,8 @@
};
usb2_phy2: phy at 4a085000 {
- compatible = "ti,omap-usb2";
+ compatible = "ti,dra7x-usb2-phy2",
+ "ti,omap-usb2";
reg = <0x4a085000 0x400>;
ctrl-module = <&omap_control_usb2phy2>;
clocks = <&usb_phy2_always_on_clk32k>,
--
1.7.9.5
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v3 4/4] ARM: dts: <am4372/dra7/omap5>: Use "syscon-phy-power" instead of "ctrl-module"
2015-12-15 9:39 ` Kishon Vijay Abraham I
(?)
@ 2015-12-15 9:39 ` Kishon Vijay Abraham I
-1 siblings, 0 replies; 24+ messages in thread
From: Kishon Vijay Abraham I @ 2015-12-15 9:39 UTC (permalink / raw)
To: devicetree, linux-kernel, linux-omap, tony
Cc: bcousson, kishon, robh+dt, pawel.moll, mark.rutland,
ijc+devicetree, galak, linux, rogerq, nsekhar, linux-arm-kernel,
linux-pci, linux-usb, t-kristo
Add "syscon-phy-power" property and remove the deprecated "ctrl-module"
property from SATA and USB PHY node. Also remove the unused control
module dt nodes.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
arch/arm/boot/dts/am4372.dtsi | 16 ++--------------
arch/arm/boot/dts/dra7.dtsi | 34 ++++------------------------------
arch/arm/boot/dts/omap5.dtsi | 26 +++-----------------------
3 files changed, 9 insertions(+), 67 deletions(-)
diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi
index d83ff9c..f42d4a4 100644
--- a/arch/arm/boot/dts/am4372.dtsi
+++ b/arch/arm/boot/dts/am4372.dtsi
@@ -853,18 +853,6 @@
status = "disabled";
};
- am43xx_control_usb2phy1: control-phy@44e10620 {
- compatible = "ti,control-phy-usb2-am437";
- reg = <0x44e10620 0x4>;
- reg-names = "power";
- };
-
- am43xx_control_usb2phy2: control-phy@0x44e10628 {
- compatible = "ti,control-phy-usb2-am437";
- reg = <0x44e10628 0x4>;
- reg-names = "power";
- };
-
ocp2scp0: ocp2scp@483a8000 {
compatible = "ti,am437x-ocp2scp", "ti,omap-ocp2scp";
#address-cells = <1>;
@@ -875,7 +863,7 @@
usb2_phy1: phy@483a8000 {
compatible = "ti,am437x-usb2";
reg = <0x483a8000 0x8000>;
- ctrl-module = <&am43xx_control_usb2phy1>;
+ syscon-phy-power = <&scm_conf 0x620>;
clocks = <&usb_phy0_always_on_clk32k>,
<&usb_otg_ss0_refclk960m>;
clock-names = "wkupclk", "refclk";
@@ -894,7 +882,7 @@
usb2_phy2: phy@483e8000 {
compatible = "ti,am437x-usb2";
reg = <0x483e8000 0x8000>;
- ctrl-module = <&am43xx_control_usb2phy2>;
+ syscon-phy-power = <&scm_conf 0x628>;
clocks = <&usb_phy1_always_on_clk32k>,
<&usb_otg_ss1_refclk960m>;
clock-names = "wkupclk", "refclk";
diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
index 41545f9..8ce37e4 100644
--- a/arch/arm/boot/dts/dra7.dtsi
+++ b/arch/arm/boot/dts/dra7.dtsi
@@ -1170,14 +1170,6 @@
status = "disabled";
};
- omap_control_sata: control-phy@4a002374 {
- compatible = "ti,control-phy-pipe3";
- reg = <0x4a002374 0x4>;
- reg-names = "power";
- clocks = <&sys_clkin1>;
- clock-names = "sysclk";
- };
-
/* OCP2SCP3 */
ocp2scp@4a090000 {
compatible = "ti,omap-ocp2scp";
@@ -1192,7 +1184,7 @@
<0x4A096400 0x64>, /* phy_tx */
<0x4A096800 0x40>; /* pll_ctrl */
reg-names = "phy_rx", "phy_tx", "pll_ctrl";
- ctrl-module = <&omap_control_sata>;
+ syscon-phy-power = <&scm_conf 0x374>;
clocks = <&sys_clkin1>, <&sata_ref_clk>;
clock-names = "sysclk", "refclk";
syscon-pllreset = <&scm_conf 0x3fc>;
@@ -1260,24 +1252,6 @@
clocks = <&sys_32k_ck>;
};
- omap_control_usb2phy1: control-phy@4a002300 {
- compatible = "ti,control-phy-usb2";
- reg = <0x4a002300 0x4>;
- reg-names = "power";
- };
-
- omap_control_usb3phy1: control-phy@4a002370 {
- compatible = "ti,control-phy-pipe3";
- reg = <0x4a002370 0x4>;
- reg-names = "power";
- };
-
- omap_control_usb2phy2: control-phy@0x4a002e74 {
- compatible = "ti,control-phy-usb2-dra7";
- reg = <0x4a002e74 0x4>;
- reg-names = "power";
- };
-
/* OCP2SCP1 */
ocp2scp@4a080000 {
compatible = "ti,omap-ocp2scp";
@@ -1290,7 +1264,7 @@
usb2_phy1: phy@4a084000 {
compatible = "ti,omap-usb2";
reg = <0x4a084000 0x400>;
- ctrl-module = <&omap_control_usb2phy1>;
+ syscon-phy-power = <&scm_conf 0x300>;
clocks = <&usb_phy1_always_on_clk32k>,
<&usb_otg_ss1_refclk960m>;
clock-names = "wkupclk",
@@ -1302,7 +1276,7 @@
compatible = "ti,dra7x-usb2-phy2",
"ti,omap-usb2";
reg = <0x4a085000 0x400>;
- ctrl-module = <&omap_control_usb2phy2>;
+ syscon-phy-power = <&scm_conf 0xe74>;
clocks = <&usb_phy2_always_on_clk32k>,
<&usb_otg_ss2_refclk960m>;
clock-names = "wkupclk",
@@ -1316,7 +1290,7 @@
<0x4a084800 0x64>,
<0x4a084c00 0x40>;
reg-names = "phy_rx", "phy_tx", "pll_ctrl";
- ctrl-module = <&omap_control_usb3phy1>;
+ syscon-phy-power = <&scm_conf 0x370>;
clocks = <&usb_phy3_always_on_clk32k>,
<&sys_clkin1>,
<&usb_otg_ss1_refclk960m>;
diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi
index 4c04389..f6d6d91 100644
--- a/arch/arm/boot/dts/omap5.dtsi
+++ b/arch/arm/boot/dts/omap5.dtsi
@@ -850,18 +850,6 @@
hw-caps-temp-alert;
};
- omap_control_usb2phy: control-phy@4a002300 {
- compatible = "ti,control-phy-usb2";
- reg = <0x4a002300 0x4>;
- reg-names = "power";
- };
-
- omap_control_usb3phy: control-phy@4a002370 {
- compatible = "ti,control-phy-pipe3";
- reg = <0x4a002370 0x4>;
- reg-names = "power";
- };
-
usb3: omap_dwc3@4a020000 {
compatible = "ti,dwc3";
ti,hwmods = "usb_otg_ss";
@@ -897,7 +885,7 @@
usb2_phy: usb2phy@4a084000 {
compatible = "ti,omap-usb2";
reg = <0x4a084000 0x7c>;
- ctrl-module = <&omap_control_usb2phy>;
+ syscon-phy-power = <&scm_conf 0x300>;
clocks = <&usb_phy_cm_clk32k>, <&usb_otg_ss_refclk960m>;
clock-names = "wkupclk", "refclk";
#phy-cells = <0>;
@@ -909,7 +897,7 @@
<0x4a084800 0x64>,
<0x4a084c00 0x40>;
reg-names = "phy_rx", "phy_tx", "pll_ctrl";
- ctrl-module = <&omap_control_usb3phy>;
+ syscon-phy-power = <&scm_conf 0x370>;
clocks = <&usb_phy_cm_clk32k>,
<&sys_clkin>,
<&usb_otg_ss_refclk960m>;
@@ -965,14 +953,6 @@
#thermal-sensor-cells = <1>;
};
- omap_control_sata: control-phy@4a002374 {
- compatible = "ti,control-phy-pipe3";
- reg = <0x4a002374 0x4>;
- reg-names = "power";
- clocks = <&sys_clkin>;
- clock-names = "sysclk";
- };
-
/* OCP2SCP3 */
ocp2scp@4a090000 {
compatible = "ti,omap-ocp2scp";
@@ -987,7 +967,7 @@
<0x4A096400 0x64>, /* phy_tx */
<0x4A096800 0x40>; /* pll_ctrl */
reg-names = "phy_rx", "phy_tx", "pll_ctrl";
- ctrl-module = <&omap_control_sata>;
+ syscon-phy-power = <&scm_conf 0x374>;
clocks = <&sys_clkin>, <&sata_ref_clk>;
clock-names = "sysclk", "refclk";
#phy-cells = <0>;
--
1.7.9.5
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v3 4/4] ARM: dts: <am4372/dra7/omap5>: Use "syscon-phy-power" instead of "ctrl-module"
@ 2015-12-15 9:39 ` Kishon Vijay Abraham I
0 siblings, 0 replies; 24+ messages in thread
From: Kishon Vijay Abraham I @ 2015-12-15 9:39 UTC (permalink / raw)
To: devicetree, linux-kernel, linux-omap, tony
Cc: bcousson, kishon, robh+dt, pawel.moll, mark.rutland,
ijc+devicetree, galak, linux, rogerq, nsekhar, linux-arm-kernel,
linux-pci, linux-usb, t-kristo
Add "syscon-phy-power" property and remove the deprecated "ctrl-module"
property from SATA and USB PHY node. Also remove the unused control
module dt nodes.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
arch/arm/boot/dts/am4372.dtsi | 16 ++--------------
arch/arm/boot/dts/dra7.dtsi | 34 ++++------------------------------
arch/arm/boot/dts/omap5.dtsi | 26 +++-----------------------
3 files changed, 9 insertions(+), 67 deletions(-)
diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi
index d83ff9c..f42d4a4 100644
--- a/arch/arm/boot/dts/am4372.dtsi
+++ b/arch/arm/boot/dts/am4372.dtsi
@@ -853,18 +853,6 @@
status = "disabled";
};
- am43xx_control_usb2phy1: control-phy@44e10620 {
- compatible = "ti,control-phy-usb2-am437";
- reg = <0x44e10620 0x4>;
- reg-names = "power";
- };
-
- am43xx_control_usb2phy2: control-phy@0x44e10628 {
- compatible = "ti,control-phy-usb2-am437";
- reg = <0x44e10628 0x4>;
- reg-names = "power";
- };
-
ocp2scp0: ocp2scp@483a8000 {
compatible = "ti,am437x-ocp2scp", "ti,omap-ocp2scp";
#address-cells = <1>;
@@ -875,7 +863,7 @@
usb2_phy1: phy@483a8000 {
compatible = "ti,am437x-usb2";
reg = <0x483a8000 0x8000>;
- ctrl-module = <&am43xx_control_usb2phy1>;
+ syscon-phy-power = <&scm_conf 0x620>;
clocks = <&usb_phy0_always_on_clk32k>,
<&usb_otg_ss0_refclk960m>;
clock-names = "wkupclk", "refclk";
@@ -894,7 +882,7 @@
usb2_phy2: phy@483e8000 {
compatible = "ti,am437x-usb2";
reg = <0x483e8000 0x8000>;
- ctrl-module = <&am43xx_control_usb2phy2>;
+ syscon-phy-power = <&scm_conf 0x628>;
clocks = <&usb_phy1_always_on_clk32k>,
<&usb_otg_ss1_refclk960m>;
clock-names = "wkupclk", "refclk";
diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
index 41545f9..8ce37e4 100644
--- a/arch/arm/boot/dts/dra7.dtsi
+++ b/arch/arm/boot/dts/dra7.dtsi
@@ -1170,14 +1170,6 @@
status = "disabled";
};
- omap_control_sata: control-phy@4a002374 {
- compatible = "ti,control-phy-pipe3";
- reg = <0x4a002374 0x4>;
- reg-names = "power";
- clocks = <&sys_clkin1>;
- clock-names = "sysclk";
- };
-
/* OCP2SCP3 */
ocp2scp@4a090000 {
compatible = "ti,omap-ocp2scp";
@@ -1192,7 +1184,7 @@
<0x4A096400 0x64>, /* phy_tx */
<0x4A096800 0x40>; /* pll_ctrl */
reg-names = "phy_rx", "phy_tx", "pll_ctrl";
- ctrl-module = <&omap_control_sata>;
+ syscon-phy-power = <&scm_conf 0x374>;
clocks = <&sys_clkin1>, <&sata_ref_clk>;
clock-names = "sysclk", "refclk";
syscon-pllreset = <&scm_conf 0x3fc>;
@@ -1260,24 +1252,6 @@
clocks = <&sys_32k_ck>;
};
- omap_control_usb2phy1: control-phy@4a002300 {
- compatible = "ti,control-phy-usb2";
- reg = <0x4a002300 0x4>;
- reg-names = "power";
- };
-
- omap_control_usb3phy1: control-phy@4a002370 {
- compatible = "ti,control-phy-pipe3";
- reg = <0x4a002370 0x4>;
- reg-names = "power";
- };
-
- omap_control_usb2phy2: control-phy@0x4a002e74 {
- compatible = "ti,control-phy-usb2-dra7";
- reg = <0x4a002e74 0x4>;
- reg-names = "power";
- };
-
/* OCP2SCP1 */
ocp2scp@4a080000 {
compatible = "ti,omap-ocp2scp";
@@ -1290,7 +1264,7 @@
usb2_phy1: phy@4a084000 {
compatible = "ti,omap-usb2";
reg = <0x4a084000 0x400>;
- ctrl-module = <&omap_control_usb2phy1>;
+ syscon-phy-power = <&scm_conf 0x300>;
clocks = <&usb_phy1_always_on_clk32k>,
<&usb_otg_ss1_refclk960m>;
clock-names = "wkupclk",
@@ -1302,7 +1276,7 @@
compatible = "ti,dra7x-usb2-phy2",
"ti,omap-usb2";
reg = <0x4a085000 0x400>;
- ctrl-module = <&omap_control_usb2phy2>;
+ syscon-phy-power = <&scm_conf 0xe74>;
clocks = <&usb_phy2_always_on_clk32k>,
<&usb_otg_ss2_refclk960m>;
clock-names = "wkupclk",
@@ -1316,7 +1290,7 @@
<0x4a084800 0x64>,
<0x4a084c00 0x40>;
reg-names = "phy_rx", "phy_tx", "pll_ctrl";
- ctrl-module = <&omap_control_usb3phy1>;
+ syscon-phy-power = <&scm_conf 0x370>;
clocks = <&usb_phy3_always_on_clk32k>,
<&sys_clkin1>,
<&usb_otg_ss1_refclk960m>;
diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi
index 4c04389..f6d6d91 100644
--- a/arch/arm/boot/dts/omap5.dtsi
+++ b/arch/arm/boot/dts/omap5.dtsi
@@ -850,18 +850,6 @@
hw-caps-temp-alert;
};
- omap_control_usb2phy: control-phy@4a002300 {
- compatible = "ti,control-phy-usb2";
- reg = <0x4a002300 0x4>;
- reg-names = "power";
- };
-
- omap_control_usb3phy: control-phy@4a002370 {
- compatible = "ti,control-phy-pipe3";
- reg = <0x4a002370 0x4>;
- reg-names = "power";
- };
-
usb3: omap_dwc3@4a020000 {
compatible = "ti,dwc3";
ti,hwmods = "usb_otg_ss";
@@ -897,7 +885,7 @@
usb2_phy: usb2phy@4a084000 {
compatible = "ti,omap-usb2";
reg = <0x4a084000 0x7c>;
- ctrl-module = <&omap_control_usb2phy>;
+ syscon-phy-power = <&scm_conf 0x300>;
clocks = <&usb_phy_cm_clk32k>, <&usb_otg_ss_refclk960m>;
clock-names = "wkupclk", "refclk";
#phy-cells = <0>;
@@ -909,7 +897,7 @@
<0x4a084800 0x64>,
<0x4a084c00 0x40>;
reg-names = "phy_rx", "phy_tx", "pll_ctrl";
- ctrl-module = <&omap_control_usb3phy>;
+ syscon-phy-power = <&scm_conf 0x370>;
clocks = <&usb_phy_cm_clk32k>,
<&sys_clkin>,
<&usb_otg_ss_refclk960m>;
@@ -965,14 +953,6 @@
#thermal-sensor-cells = <1>;
};
- omap_control_sata: control-phy@4a002374 {
- compatible = "ti,control-phy-pipe3";
- reg = <0x4a002374 0x4>;
- reg-names = "power";
- clocks = <&sys_clkin>;
- clock-names = "sysclk";
- };
-
/* OCP2SCP3 */
ocp2scp@4a090000 {
compatible = "ti,omap-ocp2scp";
@@ -987,7 +967,7 @@
<0x4A096400 0x64>, /* phy_tx */
<0x4A096800 0x40>; /* pll_ctrl */
reg-names = "phy_rx", "phy_tx", "pll_ctrl";
- ctrl-module = <&omap_control_sata>;
+ syscon-phy-power = <&scm_conf 0x374>;
clocks = <&sys_clkin>, <&sata_ref_clk>;
clock-names = "sysclk", "refclk";
#phy-cells = <0>;
--
1.7.9.5
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v3 4/4] ARM: dts: <am4372/dra7/omap5>: Use "syscon-phy-power" instead of "ctrl-module"
@ 2015-12-15 9:39 ` Kishon Vijay Abraham I
0 siblings, 0 replies; 24+ messages in thread
From: Kishon Vijay Abraham I @ 2015-12-15 9:39 UTC (permalink / raw)
To: linux-arm-kernel
Add "syscon-phy-power" property and remove the deprecated "ctrl-module"
property from SATA and USB PHY node. Also remove the unused control
module dt nodes.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
arch/arm/boot/dts/am4372.dtsi | 16 ++--------------
arch/arm/boot/dts/dra7.dtsi | 34 ++++------------------------------
arch/arm/boot/dts/omap5.dtsi | 26 +++-----------------------
3 files changed, 9 insertions(+), 67 deletions(-)
diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi
index d83ff9c..f42d4a4 100644
--- a/arch/arm/boot/dts/am4372.dtsi
+++ b/arch/arm/boot/dts/am4372.dtsi
@@ -853,18 +853,6 @@
status = "disabled";
};
- am43xx_control_usb2phy1: control-phy at 44e10620 {
- compatible = "ti,control-phy-usb2-am437";
- reg = <0x44e10620 0x4>;
- reg-names = "power";
- };
-
- am43xx_control_usb2phy2: control-phy at 0x44e10628 {
- compatible = "ti,control-phy-usb2-am437";
- reg = <0x44e10628 0x4>;
- reg-names = "power";
- };
-
ocp2scp0: ocp2scp at 483a8000 {
compatible = "ti,am437x-ocp2scp", "ti,omap-ocp2scp";
#address-cells = <1>;
@@ -875,7 +863,7 @@
usb2_phy1: phy at 483a8000 {
compatible = "ti,am437x-usb2";
reg = <0x483a8000 0x8000>;
- ctrl-module = <&am43xx_control_usb2phy1>;
+ syscon-phy-power = <&scm_conf 0x620>;
clocks = <&usb_phy0_always_on_clk32k>,
<&usb_otg_ss0_refclk960m>;
clock-names = "wkupclk", "refclk";
@@ -894,7 +882,7 @@
usb2_phy2: phy at 483e8000 {
compatible = "ti,am437x-usb2";
reg = <0x483e8000 0x8000>;
- ctrl-module = <&am43xx_control_usb2phy2>;
+ syscon-phy-power = <&scm_conf 0x628>;
clocks = <&usb_phy1_always_on_clk32k>,
<&usb_otg_ss1_refclk960m>;
clock-names = "wkupclk", "refclk";
diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
index 41545f9..8ce37e4 100644
--- a/arch/arm/boot/dts/dra7.dtsi
+++ b/arch/arm/boot/dts/dra7.dtsi
@@ -1170,14 +1170,6 @@
status = "disabled";
};
- omap_control_sata: control-phy at 4a002374 {
- compatible = "ti,control-phy-pipe3";
- reg = <0x4a002374 0x4>;
- reg-names = "power";
- clocks = <&sys_clkin1>;
- clock-names = "sysclk";
- };
-
/* OCP2SCP3 */
ocp2scp at 4a090000 {
compatible = "ti,omap-ocp2scp";
@@ -1192,7 +1184,7 @@
<0x4A096400 0x64>, /* phy_tx */
<0x4A096800 0x40>; /* pll_ctrl */
reg-names = "phy_rx", "phy_tx", "pll_ctrl";
- ctrl-module = <&omap_control_sata>;
+ syscon-phy-power = <&scm_conf 0x374>;
clocks = <&sys_clkin1>, <&sata_ref_clk>;
clock-names = "sysclk", "refclk";
syscon-pllreset = <&scm_conf 0x3fc>;
@@ -1260,24 +1252,6 @@
clocks = <&sys_32k_ck>;
};
- omap_control_usb2phy1: control-phy at 4a002300 {
- compatible = "ti,control-phy-usb2";
- reg = <0x4a002300 0x4>;
- reg-names = "power";
- };
-
- omap_control_usb3phy1: control-phy at 4a002370 {
- compatible = "ti,control-phy-pipe3";
- reg = <0x4a002370 0x4>;
- reg-names = "power";
- };
-
- omap_control_usb2phy2: control-phy at 0x4a002e74 {
- compatible = "ti,control-phy-usb2-dra7";
- reg = <0x4a002e74 0x4>;
- reg-names = "power";
- };
-
/* OCP2SCP1 */
ocp2scp at 4a080000 {
compatible = "ti,omap-ocp2scp";
@@ -1290,7 +1264,7 @@
usb2_phy1: phy at 4a084000 {
compatible = "ti,omap-usb2";
reg = <0x4a084000 0x400>;
- ctrl-module = <&omap_control_usb2phy1>;
+ syscon-phy-power = <&scm_conf 0x300>;
clocks = <&usb_phy1_always_on_clk32k>,
<&usb_otg_ss1_refclk960m>;
clock-names = "wkupclk",
@@ -1302,7 +1276,7 @@
compatible = "ti,dra7x-usb2-phy2",
"ti,omap-usb2";
reg = <0x4a085000 0x400>;
- ctrl-module = <&omap_control_usb2phy2>;
+ syscon-phy-power = <&scm_conf 0xe74>;
clocks = <&usb_phy2_always_on_clk32k>,
<&usb_otg_ss2_refclk960m>;
clock-names = "wkupclk",
@@ -1316,7 +1290,7 @@
<0x4a084800 0x64>,
<0x4a084c00 0x40>;
reg-names = "phy_rx", "phy_tx", "pll_ctrl";
- ctrl-module = <&omap_control_usb3phy1>;
+ syscon-phy-power = <&scm_conf 0x370>;
clocks = <&usb_phy3_always_on_clk32k>,
<&sys_clkin1>,
<&usb_otg_ss1_refclk960m>;
diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi
index 4c04389..f6d6d91 100644
--- a/arch/arm/boot/dts/omap5.dtsi
+++ b/arch/arm/boot/dts/omap5.dtsi
@@ -850,18 +850,6 @@
hw-caps-temp-alert;
};
- omap_control_usb2phy: control-phy at 4a002300 {
- compatible = "ti,control-phy-usb2";
- reg = <0x4a002300 0x4>;
- reg-names = "power";
- };
-
- omap_control_usb3phy: control-phy at 4a002370 {
- compatible = "ti,control-phy-pipe3";
- reg = <0x4a002370 0x4>;
- reg-names = "power";
- };
-
usb3: omap_dwc3 at 4a020000 {
compatible = "ti,dwc3";
ti,hwmods = "usb_otg_ss";
@@ -897,7 +885,7 @@
usb2_phy: usb2phy at 4a084000 {
compatible = "ti,omap-usb2";
reg = <0x4a084000 0x7c>;
- ctrl-module = <&omap_control_usb2phy>;
+ syscon-phy-power = <&scm_conf 0x300>;
clocks = <&usb_phy_cm_clk32k>, <&usb_otg_ss_refclk960m>;
clock-names = "wkupclk", "refclk";
#phy-cells = <0>;
@@ -909,7 +897,7 @@
<0x4a084800 0x64>,
<0x4a084c00 0x40>;
reg-names = "phy_rx", "phy_tx", "pll_ctrl";
- ctrl-module = <&omap_control_usb3phy>;
+ syscon-phy-power = <&scm_conf 0x370>;
clocks = <&usb_phy_cm_clk32k>,
<&sys_clkin>,
<&usb_otg_ss_refclk960m>;
@@ -965,14 +953,6 @@
#thermal-sensor-cells = <1>;
};
- omap_control_sata: control-phy at 4a002374 {
- compatible = "ti,control-phy-pipe3";
- reg = <0x4a002374 0x4>;
- reg-names = "power";
- clocks = <&sys_clkin>;
- clock-names = "sysclk";
- };
-
/* OCP2SCP3 */
ocp2scp at 4a090000 {
compatible = "ti,omap-ocp2scp";
@@ -987,7 +967,7 @@
<0x4A096400 0x64>, /* phy_tx */
<0x4A096800 0x40>; /* pll_ctrl */
reg-names = "phy_rx", "phy_tx", "pll_ctrl";
- ctrl-module = <&omap_control_sata>;
+ syscon-phy-power = <&scm_conf 0x374>;
clocks = <&sys_clkin>, <&sata_ref_clk>;
clock-names = "sysclk", "refclk";
#phy-cells = <0>;
--
1.7.9.5
^ permalink raw reply related [flat|nested] 24+ messages in thread
* Re: [PATCH v3 1/4] ARM: dts: dra7: Add dt node for the sycon pcie
@ 2015-12-15 13:22 ` Sergei Shtylyov
0 siblings, 0 replies; 24+ messages in thread
From: Sergei Shtylyov @ 2015-12-15 13:22 UTC (permalink / raw)
To: Kishon Vijay Abraham I, devicetree, linux-kernel, linux-omap, tony
Cc: bcousson, robh+dt, pawel.moll, mark.rutland, ijc+devicetree,
galak, linux, rogerq, nsekhar, linux-arm-kernel, linux-pci,
linux-usb, t-kristo
Hello.
On 12/15/2015 12:39 PM, Kishon Vijay Abraham I wrote:
> Add new device tree node for the control module register space where
> PCIe registers are present.
>
> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
> ---
> arch/arm/boot/dts/dra7.dtsi | 5 +++++
> 1 file changed, 5 insertions(+)
>
> diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
> index fe99231..e38f63f 100644
> --- a/arch/arm/boot/dts/dra7.dtsi
> +++ b/arch/arm/boot/dts/dra7.dtsi
> @@ -155,6 +155,11 @@
> compatible = "syscon";
> reg = <0x1c04 0x0020>;
> };
> +
> + scm_conf_pcie: tisyscon@1c24 {
Please use the generic node names as the ePAPR standard says.
[...]
MBR, Sergei
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH v3 1/4] ARM: dts: dra7: Add dt node for the sycon pcie
@ 2015-12-15 13:22 ` Sergei Shtylyov
0 siblings, 0 replies; 24+ messages in thread
From: Sergei Shtylyov @ 2015-12-15 13:22 UTC (permalink / raw)
To: Kishon Vijay Abraham I, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-omap-u79uwXL29TY76Z2rM5mHXA, tony-4v6yS6AI5VpBDgjK7y7TUQ
Cc: bcousson-rdvid1DuHRBWk0Htik3J/w, robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
pawel.moll-5wv7dgnIgG8, mark.rutland-5wv7dgnIgG8,
ijc+devicetree-KcIKpvwj1kUDXYZnReoRVg,
galak-sgV2jX0FEOL9JmXXK+q4OQ, linux-lFZ/pmaqli7XmaaqVzeoHQ,
rogerq-l0cyMroinI0, nsekhar-l0cyMroinI0,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-pci-u79uwXL29TY76Z2rM5mHXA,
linux-usb-u79uwXL29TY76Z2rM5mHXA, t-kristo-l0cyMroinI0
Hello.
On 12/15/2015 12:39 PM, Kishon Vijay Abraham I wrote:
> Add new device tree node for the control module register space where
> PCIe registers are present.
>
> Signed-off-by: Kishon Vijay Abraham I <kishon-l0cyMroinI0@public.gmane.org>
> ---
> arch/arm/boot/dts/dra7.dtsi | 5 +++++
> 1 file changed, 5 insertions(+)
>
> diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
> index fe99231..e38f63f 100644
> --- a/arch/arm/boot/dts/dra7.dtsi
> +++ b/arch/arm/boot/dts/dra7.dtsi
> @@ -155,6 +155,11 @@
> compatible = "syscon";
> reg = <0x1c04 0x0020>;
> };
> +
> + scm_conf_pcie: tisyscon@1c24 {
Please use the generic node names as the ePAPR standard says.
[...]
MBR, Sergei
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 24+ messages in thread
* [PATCH v3 1/4] ARM: dts: dra7: Add dt node for the sycon pcie
@ 2015-12-15 13:22 ` Sergei Shtylyov
0 siblings, 0 replies; 24+ messages in thread
From: Sergei Shtylyov @ 2015-12-15 13:22 UTC (permalink / raw)
To: linux-arm-kernel
Hello.
On 12/15/2015 12:39 PM, Kishon Vijay Abraham I wrote:
> Add new device tree node for the control module register space where
> PCIe registers are present.
>
> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
> ---
> arch/arm/boot/dts/dra7.dtsi | 5 +++++
> 1 file changed, 5 insertions(+)
>
> diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
> index fe99231..e38f63f 100644
> --- a/arch/arm/boot/dts/dra7.dtsi
> +++ b/arch/arm/boot/dts/dra7.dtsi
> @@ -155,6 +155,11 @@
> compatible = "syscon";
> reg = <0x1c04 0x0020>;
> };
> +
> + scm_conf_pcie: tisyscon at 1c24 {
Please use the generic node names as the ePAPR standard says.
[...]
MBR, Sergei
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH v3 1/4] ARM: dts: dra7: Add dt node for the sycon pcie
2015-12-15 13:22 ` Sergei Shtylyov
(?)
@ 2015-12-18 10:21 ` Kishon Vijay Abraham I
-1 siblings, 0 replies; 24+ messages in thread
From: Kishon Vijay Abraham I @ 2015-12-18 10:21 UTC (permalink / raw)
To: Sergei Shtylyov, devicetree, linux-kernel, linux-omap, tony
Cc: bcousson, robh+dt, pawel.moll, mark.rutland, ijc+devicetree,
galak, linux, rogerq, nsekhar, linux-arm-kernel, linux-pci,
linux-usb, t-kristo
Hi,
On Tuesday 15 December 2015 06:52 PM, Sergei Shtylyov wrote:
> Hello.
>
> On 12/15/2015 12:39 PM, Kishon Vijay Abraham I wrote:
>
>> Add new device tree node for the control module register space where
>> PCIe registers are present.
>>
>> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
>> ---
>> arch/arm/boot/dts/dra7.dtsi | 5 +++++
>> 1 file changed, 5 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
>> index fe99231..e38f63f 100644
>> --- a/arch/arm/boot/dts/dra7.dtsi
>> +++ b/arch/arm/boot/dts/dra7.dtsi
>> @@ -155,6 +155,11 @@
>> compatible = "syscon";
>> reg = <0x1c04 0x0020>;
>> };
>> +
>> + scm_conf_pcie: tisyscon@1c24 {
>
> Please use the generic node names as the ePAPR standard says.
something like scm_conf_pcie: syscon@1c24??
Thanks
Kishon
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH v3 1/4] ARM: dts: dra7: Add dt node for the sycon pcie
@ 2015-12-18 10:21 ` Kishon Vijay Abraham I
0 siblings, 0 replies; 24+ messages in thread
From: Kishon Vijay Abraham I @ 2015-12-18 10:21 UTC (permalink / raw)
To: Sergei Shtylyov, devicetree, linux-kernel, linux-omap, tony
Cc: bcousson, robh+dt, pawel.moll, mark.rutland, ijc+devicetree,
galak, linux, rogerq, nsekhar, linux-arm-kernel, linux-pci,
linux-usb, t-kristo
Hi,
On Tuesday 15 December 2015 06:52 PM, Sergei Shtylyov wrote:
> Hello.
>
> On 12/15/2015 12:39 PM, Kishon Vijay Abraham I wrote:
>
>> Add new device tree node for the control module register space where
>> PCIe registers are present.
>>
>> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
>> ---
>> arch/arm/boot/dts/dra7.dtsi | 5 +++++
>> 1 file changed, 5 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
>> index fe99231..e38f63f 100644
>> --- a/arch/arm/boot/dts/dra7.dtsi
>> +++ b/arch/arm/boot/dts/dra7.dtsi
>> @@ -155,6 +155,11 @@
>> compatible = "syscon";
>> reg = <0x1c04 0x0020>;
>> };
>> +
>> + scm_conf_pcie: tisyscon@1c24 {
>
> Please use the generic node names as the ePAPR standard says.
something like scm_conf_pcie: syscon@1c24??
Thanks
Kishon
^ permalink raw reply [flat|nested] 24+ messages in thread
* [PATCH v3 1/4] ARM: dts: dra7: Add dt node for the sycon pcie
@ 2015-12-18 10:21 ` Kishon Vijay Abraham I
0 siblings, 0 replies; 24+ messages in thread
From: Kishon Vijay Abraham I @ 2015-12-18 10:21 UTC (permalink / raw)
To: linux-arm-kernel
Hi,
On Tuesday 15 December 2015 06:52 PM, Sergei Shtylyov wrote:
> Hello.
>
> On 12/15/2015 12:39 PM, Kishon Vijay Abraham I wrote:
>
>> Add new device tree node for the control module register space where
>> PCIe registers are present.
>>
>> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
>> ---
>> arch/arm/boot/dts/dra7.dtsi | 5 +++++
>> 1 file changed, 5 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
>> index fe99231..e38f63f 100644
>> --- a/arch/arm/boot/dts/dra7.dtsi
>> +++ b/arch/arm/boot/dts/dra7.dtsi
>> @@ -155,6 +155,11 @@
>> compatible = "syscon";
>> reg = <0x1c04 0x0020>;
>> };
>> +
>> + scm_conf_pcie: tisyscon at 1c24 {
>
> Please use the generic node names as the ePAPR standard says.
something like scm_conf_pcie: syscon at 1c24??
Thanks
Kishon
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH v3 1/4] ARM: dts: dra7: Add dt node for the sycon pcie
@ 2015-12-18 11:32 ` Sergei Shtylyov
0 siblings, 0 replies; 24+ messages in thread
From: Sergei Shtylyov @ 2015-12-18 11:32 UTC (permalink / raw)
To: Kishon Vijay Abraham I, devicetree, linux-kernel, linux-omap, tony
Cc: bcousson, robh+dt, pawel.moll, mark.rutland, ijc+devicetree,
galak, linux, rogerq, nsekhar, linux-arm-kernel, linux-pci,
linux-usb, t-kristo
Hello.
On 12/18/2015 1:21 PM, Kishon Vijay Abraham I wrote:
>>> Add new device tree node for the control module register space where
>>> PCIe registers are present.
>>>
>>> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
>>> ---
>>> arch/arm/boot/dts/dra7.dtsi | 5 +++++
>>> 1 file changed, 5 insertions(+)
>>>
>>> diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
>>> index fe99231..e38f63f 100644
>>> --- a/arch/arm/boot/dts/dra7.dtsi
>>> +++ b/arch/arm/boot/dts/dra7.dtsi
>>> @@ -155,6 +155,11 @@
>>> compatible = "syscon";
>>> reg = <0x1c04 0x0020>;
>>> };
>>> +
>>> + scm_conf_pcie: tisyscon@1c24 {
>>
>> Please use the generic node names as the ePAPR standard says.
>
> something like scm_conf_pcie: syscon@1c24??
Yes, though "system-controller" would be probably more in line with what
ePAPR has standardized.
> Thanks
> Kishon
MBR, Sergei
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH v3 1/4] ARM: dts: dra7: Add dt node for the sycon pcie
@ 2015-12-18 11:32 ` Sergei Shtylyov
0 siblings, 0 replies; 24+ messages in thread
From: Sergei Shtylyov @ 2015-12-18 11:32 UTC (permalink / raw)
To: Kishon Vijay Abraham I, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-omap-u79uwXL29TY76Z2rM5mHXA, tony-4v6yS6AI5VpBDgjK7y7TUQ
Cc: bcousson-rdvid1DuHRBWk0Htik3J/w, robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
pawel.moll-5wv7dgnIgG8, mark.rutland-5wv7dgnIgG8,
ijc+devicetree-KcIKpvwj1kUDXYZnReoRVg,
galak-sgV2jX0FEOL9JmXXK+q4OQ, linux-lFZ/pmaqli7XmaaqVzeoHQ,
rogerq-l0cyMroinI0, nsekhar-l0cyMroinI0,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-pci-u79uwXL29TY76Z2rM5mHXA,
linux-usb-u79uwXL29TY76Z2rM5mHXA, t-kristo-l0cyMroinI0
Hello.
On 12/18/2015 1:21 PM, Kishon Vijay Abraham I wrote:
>>> Add new device tree node for the control module register space where
>>> PCIe registers are present.
>>>
>>> Signed-off-by: Kishon Vijay Abraham I <kishon-l0cyMroinI0@public.gmane.org>
>>> ---
>>> arch/arm/boot/dts/dra7.dtsi | 5 +++++
>>> 1 file changed, 5 insertions(+)
>>>
>>> diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
>>> index fe99231..e38f63f 100644
>>> --- a/arch/arm/boot/dts/dra7.dtsi
>>> +++ b/arch/arm/boot/dts/dra7.dtsi
>>> @@ -155,6 +155,11 @@
>>> compatible = "syscon";
>>> reg = <0x1c04 0x0020>;
>>> };
>>> +
>>> + scm_conf_pcie: tisyscon@1c24 {
>>
>> Please use the generic node names as the ePAPR standard says.
>
> something like scm_conf_pcie: syscon@1c24??
Yes, though "system-controller" would be probably more in line with what
ePAPR has standardized.
> Thanks
> Kishon
MBR, Sergei
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 24+ messages in thread
* [PATCH v3 1/4] ARM: dts: dra7: Add dt node for the sycon pcie
@ 2015-12-18 11:32 ` Sergei Shtylyov
0 siblings, 0 replies; 24+ messages in thread
From: Sergei Shtylyov @ 2015-12-18 11:32 UTC (permalink / raw)
To: linux-arm-kernel
Hello.
On 12/18/2015 1:21 PM, Kishon Vijay Abraham I wrote:
>>> Add new device tree node for the control module register space where
>>> PCIe registers are present.
>>>
>>> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
>>> ---
>>> arch/arm/boot/dts/dra7.dtsi | 5 +++++
>>> 1 file changed, 5 insertions(+)
>>>
>>> diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
>>> index fe99231..e38f63f 100644
>>> --- a/arch/arm/boot/dts/dra7.dtsi
>>> +++ b/arch/arm/boot/dts/dra7.dtsi
>>> @@ -155,6 +155,11 @@
>>> compatible = "syscon";
>>> reg = <0x1c04 0x0020>;
>>> };
>>> +
>>> + scm_conf_pcie: tisyscon at 1c24 {
>>
>> Please use the generic node names as the ePAPR standard says.
>
> something like scm_conf_pcie: syscon at 1c24??
Yes, though "system-controller" would be probably more in line with what
ePAPR has standardized.
> Thanks
> Kishon
MBR, Sergei
^ permalink raw reply [flat|nested] 24+ messages in thread
end of thread, other threads:[~2015-12-18 11:33 UTC | newest]
Thread overview: 24+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2015-12-15 9:39 [PATCH v3 0/4] ARM: dts: use syscon property instead of ctrl-module Kishon Vijay Abraham I
2015-12-15 9:39 ` Kishon Vijay Abraham I
2015-12-15 9:39 ` Kishon Vijay Abraham I
2015-12-15 9:39 ` [PATCH v3 1/4] ARM: dts: dra7: Add dt node for the sycon pcie Kishon Vijay Abraham I
2015-12-15 9:39 ` Kishon Vijay Abraham I
2015-12-15 9:39 ` Kishon Vijay Abraham I
2015-12-15 13:22 ` Sergei Shtylyov
2015-12-15 13:22 ` Sergei Shtylyov
2015-12-15 13:22 ` Sergei Shtylyov
2015-12-18 10:21 ` Kishon Vijay Abraham I
2015-12-18 10:21 ` Kishon Vijay Abraham I
2015-12-18 10:21 ` Kishon Vijay Abraham I
2015-12-18 11:32 ` Sergei Shtylyov
2015-12-18 11:32 ` Sergei Shtylyov
2015-12-18 11:32 ` Sergei Shtylyov
2015-12-15 9:39 ` [PATCH v3 2/4] ARM: dts: dra7: Use "syscon-phy-power" and "syscon-pcs" in PCIe PHY node Kishon Vijay Abraham I
2015-12-15 9:39 ` Kishon Vijay Abraham I
2015-12-15 9:39 ` Kishon Vijay Abraham I
2015-12-15 9:39 ` [PATCH v3 3/4] ARM: dts: dra7: Use "ti,dra7x-usb2-phy2" compatible string for USB2 PHY2 Kishon Vijay Abraham I
2015-12-15 9:39 ` [PATCH v3 3/4] ARM: dts: dra7: Use "ti, dra7x-usb2-phy2" " Kishon Vijay Abraham I
2015-12-15 9:39 ` [PATCH v3 3/4] ARM: dts: dra7: Use "ti,dra7x-usb2-phy2" " Kishon Vijay Abraham I
2015-12-15 9:39 ` [PATCH v3 4/4] ARM: dts: <am4372/dra7/omap5>: Use "syscon-phy-power" instead of "ctrl-module" Kishon Vijay Abraham I
2015-12-15 9:39 ` Kishon Vijay Abraham I
2015-12-15 9:39 ` Kishon Vijay Abraham I
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.