* [RFT PATCH v2 2/2] arm64: dts: qcom: sdm845: align TLMM pin configuration with DT schema
2022-11-18 16:42 [RFT PATCH v2 1/2] arm64: dts: qcom: sdm845-db845c: drop unneeded qup_spi0_default Krzysztof Kozlowski
@ 2022-11-18 16:42 ` Krzysztof Kozlowski
2022-12-02 0:50 ` Doug Anderson
2022-11-18 16:51 ` [RFT PATCH v2 1/2] arm64: dts: qcom: sdm845-db845c: drop unneeded qup_spi0_default Konrad Dybcio
2022-12-02 0:49 ` Doug Anderson
2 siblings, 1 reply; 10+ messages in thread
From: Krzysztof Kozlowski @ 2022-11-18 16:42 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Konrad Dybcio, Rob Herring,
Krzysztof Kozlowski, linux-arm-msm, devicetree, linux-kernel
Cc: Krzysztof Kozlowski, Doug Anderson
DT schema expects TLMM pin configuration nodes to be named with
'-state' suffix and their optional children with '-pins' suffix.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
Cc: Doug Anderson <dianders@chromium.org>
Tested on Qualcomm RB3. Please kndly test a bit more on other devices.
This should not have an functional impact.
Changes since v1:
1. Address comments and implement conclusion with Doug. Drop
default-pins/pinmux/mux/config nodes but instead add subnodes for
specific pins for UARTs. This should match approach used for SC7180.
v1: https://lore.kernel.org/linux-kernel/1b9dcca8-1abd-99a3-da12-a8763bf77f12@linaro.org/
---
arch/arm64/boot/dts/qcom/sdm845-cheza.dtsi | 397 ++++------
arch/arm64/boot/dts/qcom/sdm845-db845c.dts | 82 +--
.../arm64/boot/dts/qcom/sdm845-lg-common.dtsi | 60 +-
arch/arm64/boot/dts/qcom/sdm845-lg-judyln.dts | 2 +-
arch/arm64/boot/dts/qcom/sdm845-mtp.dts | 77 +-
.../boot/dts/qcom/sdm845-oneplus-common.dtsi | 101 ++-
.../boot/dts/qcom/sdm845-shift-axolotl.dts | 150 ++--
.../dts/qcom/sdm845-sony-xperia-tama.dtsi | 6 +-
.../qcom/sdm845-xiaomi-beryllium-common.dtsi | 12 +-
.../boot/dts/qcom/sdm845-xiaomi-polaris.dts | 21 +-
arch/arm64/boot/dts/qcom/sdm845.dtsi | 676 ++++++++----------
.../boot/dts/qcom/sdm850-lenovo-yoga-c630.dts | 58 +-
.../boot/dts/qcom/sdm850-samsung-w737.dts | 126 ++--
13 files changed, 700 insertions(+), 1068 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sdm845-cheza.dtsi b/arch/arm64/boot/dts/qcom/sdm845-cheza.dtsi
index ca676e04687b..246d9339728c 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-cheza.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845-cheza.dtsi
@@ -995,104 +995,69 @@ &wifi {
/* PINCTRL - additions to nodes defined in sdm845.dtsi */
&qspi_cs0 {
- pinconf {
- pins = "gpio90";
- bias-disable;
- };
+ bias-disable;
};
&qspi_clk {
- pinconf {
- pins = "gpio95";
- bias-disable;
- };
+ bias-disable;
};
&qspi_data01 {
- pinconf {
- pins = "gpio91", "gpio92";
-
- /* High-Z when no transfers; nice to park the lines */
- bias-pull-up;
- };
+ /* High-Z when no transfers; nice to park the lines */
+ bias-pull-up;
};
&qup_i2c3_default {
- pinconf {
- pins = "gpio41", "gpio42";
- drive-strength = <2>;
+ drive-strength = <2>;
- /* Has external pullup */
- bias-disable;
- };
+ /* Has external pullup */
+ bias-disable;
};
&qup_i2c11_default {
- pinconf {
- pins = "gpio31", "gpio32";
- drive-strength = <2>;
+ drive-strength = <2>;
- /* Has external pullup */
- bias-disable;
- };
+ /* Has external pullup */
+ bias-disable;
};
&qup_i2c12_default {
- pinconf {
- pins = "gpio49", "gpio50";
- drive-strength = <2>;
+ drive-strength = <2>;
- /* Has external pullup */
- bias-disable;
- };
+ /* Has external pullup */
+ bias-disable;
};
&qup_i2c14_default {
- pinconf {
- pins = "gpio33", "gpio34";
- drive-strength = <2>;
+ drive-strength = <2>;
- /* Has external pullup */
- bias-disable;
- };
+ /* Has external pullup */
+ bias-disable;
};
&qup_spi0_default {
- pinconf {
- pins = "gpio0", "gpio1", "gpio2", "gpio3";
- drive-strength = <2>;
- bias-disable;
- };
+ drive-strength = <2>;
+ bias-disable;
};
&qup_spi5_default {
- pinconf {
- pins = "gpio85", "gpio86", "gpio87", "gpio88";
- drive-strength = <2>;
- bias-disable;
- };
+ drive-strength = <2>;
+ bias-disable;
};
&qup_spi10_default {
- pinconf {
- pins = "gpio53", "gpio54", "gpio55", "gpio56";
- drive-strength = <2>;
- bias-disable;
- };
+ drive-strength = <2>;
+ bias-disable;
};
-&qup_uart9_default {
- pinconf-tx {
- pins = "gpio4";
- drive-strength = <2>;
- bias-disable;
- };
+&qup_uart9_rx {
+ drive-strength = <2>;
+ bias-pull-up;
+};
- pinconf-rx {
- pins = "gpio5";
- drive-strength = <2>;
- bias-pull-up;
- };
+&qup_uart9_tx {
+ drive-strength = <2>;
+ bias-disable;
};
/* PINCTRL - board-specific pinctrl */
@@ -1180,243 +1145,153 @@ ap-suspend-l-hog {
output-low;
};
- ap_edp_bklten: ap-edp-bklten {
- pinmux {
- pins = "gpio37";
- function = "gpio";
- };
-
- pinconf {
- pins = "gpio37";
- drive-strength = <2>;
- bias-disable;
- };
+ ap_edp_bklten: ap-edp-bklten-state {
+ pins = "gpio37";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
};
- bios_flash_wp_r_l: bios-flash-wp-r-l {
- pinmux {
- pins = "gpio128";
- function = "gpio";
- input-enable;
- };
-
- pinconf {
- pins = "gpio128";
- bias-disable;
- };
+ bios_flash_wp_r_l: bios-flash-wp-r-l-state {
+ pins = "gpio128";
+ function = "gpio";
+ input-enable;
+ bias-disable;
};
- ec_ap_int_l: ec-ap-int-l {
- pinmux {
- pins = "gpio122";
- function = "gpio";
- input-enable;
- };
-
- pinconf {
- pins = "gpio122";
- bias-pull-up;
- };
+ ec_ap_int_l: ec-ap-int-l-state {
+ pins = "gpio122";
+ function = "gpio";
+ input-enable;
+ bias-pull-up;
};
- edp_brij_en: edp-brij-en {
- pinmux {
- pins = "gpio102";
- function = "gpio";
- };
-
- pinconf {
- pins = "gpio102";
- drive-strength = <2>;
- bias-disable;
- };
+ edp_brij_en: edp-brij-en-state {
+ pins = "gpio102";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
};
- edp_brij_irq: edp-brij-irq {
- pinmux {
- pins = "gpio10";
- function = "gpio";
- };
-
- pinconf {
- pins = "gpio10";
- drive-strength = <2>;
- bias-pull-down;
- };
+ edp_brij_irq: edp-brij-irq-state {
+ pins = "gpio10";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
};
- en_pp3300_dx_edp: en-pp3300-dx-edp {
- pinmux {
- pins = "gpio43";
- function = "gpio";
- };
-
- pinconf {
- pins = "gpio43";
- drive-strength = <2>;
- bias-disable;
- };
+ en_pp3300_dx_edp: en-pp3300-dx-edp-state {
+ pins = "gpio43";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
};
- h1_ap_int_odl: h1-ap-int-odl {
- pinmux {
- pins = "gpio129";
- function = "gpio";
- input-enable;
- };
-
- pinconf {
- pins = "gpio129";
- bias-pull-up;
- };
+ h1_ap_int_odl: h1-ap-int-odl-state {
+ pins = "gpio129";
+ function = "gpio";
+ input-enable;
+ bias-pull-up;
};
- pen_eject_odl: pen-eject-odl {
- pinmux {
- pins = "gpio119";
- function = "gpio";
- bias-pull-up;
- };
+ pen_eject_odl: pen-eject-odl-state {
+ pins = "gpio119";
+ function = "gpio";
+ bias-pull-up;
};
- pen_irq_l: pen-irq-l {
- pinmux {
- pins = "gpio24";
- function = "gpio";
- };
+ pen_irq_l: pen-irq-l-state {
+ pins = "gpio24";
+ function = "gpio";
- pinconf {
- pins = "gpio24";
-
- /* Has external pullup */
- bias-disable;
- };
+ /* Has external pullup */
+ bias-disable;
};
- pen_pdct_l: pen-pdct-l {
- pinmux {
- pins = "gpio63";
- function = "gpio";
- };
-
- pinconf {
- pins = "gpio63";
+ pen_pdct_l: pen-pdct-l-state {
+ pins = "gpio63";
+ function = "gpio";
- /* Has external pullup */
- bias-disable;
- };
+ /* Has external pullup */
+ bias-disable;
};
- pen_rst_l: pen-rst-l {
- pinmux {
- pins = "gpio23";
- function = "gpio";
- };
-
- pinconf {
- pins = "gpio23";
- bias-disable;
- drive-strength = <2>;
+ pen_rst_l: pen-rst-l-state {
+ pins = "gpio23";
+ function = "gpio";
+ bias-disable;
+ drive-strength = <2>;
- /*
- * The pen driver doesn't currently support
- * driving this reset line. By specifying
- * output-high here we're relying on the fact
- * that this pin has a default pulldown at boot
- * (which makes sure the pen was in reset if it
- * was powered) and then we set it high here to
- * take it out of reset. Better would be if the
- * pen driver could control this and we could
- * remove "output-high" here.
- */
- output-high;
- };
+ /*
+ * The pen driver doesn't currently support
+ * driving this reset line. By specifying
+ * output-high here we're relying on the fact
+ * that this pin has a default pulldown at boot
+ * (which makes sure the pen was in reset if it
+ * was powered) and then we set it high here to
+ * take it out of reset. Better would be if the
+ * pen driver could control this and we could
+ * remove "output-high" here.
+ */
+ output-high;
};
- sdc2_clk: sdc2-clk {
- pinconf {
- pins = "sdc2_clk";
- bias-disable;
+ sdc2_clk: sdc2-clk-state {
+ pins = "sdc2_clk";
+ bias-disable;
- /*
- * It seems that mmc_test reports errors if drive
- * strength is not 16.
- */
- drive-strength = <16>;
- };
+ /*
+ * It seems that mmc_test reports errors if drive
+ * strength is not 16.
+ */
+ drive-strength = <16>;
};
- sdc2_cmd: sdc2-cmd {
- pinconf {
- pins = "sdc2_cmd";
- bias-pull-up;
- drive-strength = <16>;
- };
+ sdc2_cmd: sdc2-cmd-state {
+ pins = "sdc2_cmd";
+ bias-pull-up;
+ drive-strength = <16>;
};
- sdc2_data: sdc2-data {
- pinconf {
- pins = "sdc2_data";
- bias-pull-up;
- drive-strength = <16>;
- };
+ sdc2_data: sdc2-data-state {
+ pins = "sdc2_data";
+ bias-pull-up;
+ drive-strength = <16>;
};
- sd_cd_odl: sd-cd-odl {
- pinmux {
- pins = "gpio44";
- function = "gpio";
- };
-
- pinconf {
- pins = "gpio44";
- bias-pull-up;
- };
+ sd_cd_odl: sd-cd-odl-state {
+ pins = "gpio44";
+ function = "gpio";
+ bias-pull-up;
};
- ts_int_l: ts-int-l {
- pinmux {
- pins = "gpio125";
- function = "gpio";
- };
-
- pinconf {
- pins = "gpio125";
- bias-pull-up;
- };
+ ts_int_l: ts-int-l-state {
+ pins = "gpio125";
+ function = "gpio";
+ bias-pull-up;
};
- ts_reset_l: ts-reset-l {
- pinmux {
- pins = "gpio118";
- function = "gpio";
- };
-
- pinconf {
- pins = "gpio118";
- bias-disable;
- drive-strength = <2>;
- };
+ ts_reset_l: ts-reset-l-state {
+ pins = "gpio118";
+ function = "gpio";
+ bias-disable;
+ drive-strength = <2>;
};
- ap_suspend_l_assert: ap_suspend_l_assert {
- config {
- pins = "gpio126";
- function = "gpio";
- bias-disable;
- drive-strength = <2>;
- output-low;
- };
+ ap_suspend_l_assert: ap-suspend-l-assert-state {
+ pins = "gpio126";
+ function = "gpio";
+ bias-disable;
+ drive-strength = <2>;
+ output-low;
};
- ap_suspend_l_deassert: ap_suspend_l_deassert {
- config {
- pins = "gpio126";
- function = "gpio";
- bias-disable;
- drive-strength = <2>;
- output-high;
- };
+ ap_suspend_l_deassert: ap-suspend-l-deassert-state {
+ pins = "gpio126";
+ function = "gpio";
+ bias-disable;
+ drive-strength = <2>;
+ output-high;
};
};
diff --git a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
index 56a7afb697ed..58cba83fa08d 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
@@ -830,8 +830,8 @@ &spi2 {
};
&tlmm {
- cam0_default: cam0_default {
- rst {
+ cam0_default: cam0-default-state {
+ rst-pins {
pins = "gpio9";
function = "gpio";
@@ -839,7 +839,7 @@ rst {
bias-disable;
};
- mclk0 {
+ mclk0-pins {
pins = "gpio13";
function = "cam_mclk";
@@ -848,8 +848,8 @@ mclk0 {
};
};
- cam3_default: cam3_default {
- rst {
+ cam3_default: cam3-default-state {
+ rst-pins {
function = "gpio";
pins = "gpio21";
@@ -857,7 +857,7 @@ rst {
bias-disable;
};
- mclk3 {
+ mclk3-pins {
function = "cam_mclk";
pins = "gpio16";
@@ -866,7 +866,7 @@ mclk3 {
};
};
- dsi_sw_sel: dsi-sw-sel {
+ dsi_sw_sel: dsi-sw-sel-state {
pins = "gpio120";
function = "gpio";
@@ -875,20 +875,20 @@ dsi_sw_sel: dsi-sw-sel {
output-high;
};
- lt9611_irq_pin: lt9611-irq {
+ lt9611_irq_pin: lt9611-irq-state {
pins = "gpio84";
function = "gpio";
bias-disable;
};
- pcie0_default_state: pcie0-default {
- clkreq {
+ pcie0_default_state: pcie0-default-state {
+ clkreq-pins {
pins = "gpio36";
function = "pci_e0";
bias-pull-up;
};
- reset-n {
+ reset-n-pins {
pins = "gpio35";
function = "gpio";
@@ -897,7 +897,7 @@ reset-n {
bias-pull-down;
};
- wake-n {
+ wake-n-pins {
pins = "gpio37";
function = "gpio";
@@ -906,7 +906,7 @@ wake-n {
};
};
- pcie0_pwren_state: pcie0-pwren {
+ pcie0_pwren_state: pcie0-pwren-state {
pins = "gpio90";
function = "gpio";
@@ -914,8 +914,8 @@ pcie0_pwren_state: pcie0-pwren {
bias-disable;
};
- pcie1_default_state: pcie1-default {
- perst-n {
+ pcie1_default_state: pcie1-default-state {
+ perst-n-pins {
pins = "gpio102";
function = "gpio";
@@ -923,13 +923,13 @@ perst-n {
bias-disable;
};
- clkreq {
+ clkreq-pins {
pins = "gpio103";
function = "pci_e1";
bias-pull-up;
};
- wake-n {
+ wake-n-pins {
pins = "gpio11";
function = "gpio";
@@ -937,7 +937,7 @@ wake-n {
bias-pull-up;
};
- reset-n {
+ reset-n-pins {
pins = "gpio75";
function = "gpio";
@@ -947,8 +947,8 @@ reset-n {
};
};
- sdc2_default_state: sdc2-default {
- clk {
+ sdc2_default_state: sdc2-default-state {
+ clk-pins {
pins = "sdc2_clk";
bias-disable;
@@ -959,26 +959,26 @@ clk {
drive-strength = <16>;
};
- cmd {
+ cmd-pins {
pins = "sdc2_cmd";
bias-pull-up;
drive-strength = <10>;
};
- data {
+ data-pins {
pins = "sdc2_data";
bias-pull-up;
drive-strength = <10>;
};
};
- sdc2_card_det_n: sd-card-det-n {
+ sdc2_card_det_n: sd-card-det-n-state {
pins = "gpio126";
function = "gpio";
bias-pull-up;
};
- wcd_intr_default: wcd_intr_default {
+ wcd_intr_default: wcd-intr-default-state {
pins = <54>;
function = "gpio";
@@ -1135,39 +1135,29 @@ &wifi {
/* PINCTRL - additions to nodes defined in sdm845.dtsi */
&qup_spi2_default {
- pinconf {
- pins = "gpio27", "gpio28", "gpio29", "gpio30";
- drive-strength = <16>;
- };
+ drive-strength = <16>;
};
&qup_uart3_default {
- pinmux {
- pins = "gpio41", "gpio42", "gpio43", "gpio44";
+ cts-rts-pins {
+ pins = "gpio41", "gpio42";
function = "qup3";
};
};
&qup_i2c10_default {
- pinconf {
- pins = "gpio55", "gpio56";
- drive-strength = <2>;
- bias-disable;
- };
+ drive-strength = <2>;
+ bias-disable;
};
-&qup_uart9_default {
- pinconf-tx {
- pins = "gpio4";
- drive-strength = <2>;
- bias-disable;
- };
+&qup_uart9_rx {
+ drive-strength = <2>;
+ bias-pull-up;
+};
- pinconf-rx {
- pins = "gpio5";
- drive-strength = <2>;
- bias-pull-up;
- };
+&qup_uart9_tx {
+ drive-strength = <2>;
+ bias-disable;
};
&pm8998_gpio {
diff --git a/arch/arm64/boot/dts/qcom/sdm845-lg-common.dtsi b/arch/arm64/boot/dts/qcom/sdm845-lg-common.dtsi
index 1eb423e4be24..3ccfbdb2880e 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-lg-common.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845-lg-common.dtsi
@@ -558,48 +558,36 @@ &usb_1_qmpphy {
&tlmm {
gpio-reserved-ranges = <28 4>, <81 4>;
- sdc2_clk: sdc2-clk {
- pinconf {
- pins = "sdc2_clk";
- bias-disable;
-
- /*
- * It seems that mmc_test reports errors if drive
- * strength is not 16 on clk, cmd, and data pins.
- *
- * TODO: copy-pasted from mtp, try other values
- * on these devices.
- */
- drive-strength = <16>;
- };
+ sdc2_clk: sdc2-clk-state {
+ pins = "sdc2_clk";
+ bias-disable;
+
+ /*
+ * It seems that mmc_test reports errors if drive
+ * strength is not 16 on clk, cmd, and data pins.
+ *
+ * TODO: copy-pasted from mtp, try other values
+ * on these devices.
+ */
+ drive-strength = <16>;
};
- sdc2_cmd: sdc2-cmd {
- pinconf {
- pins = "sdc2_cmd";
- bias-pull-up;
- drive-strength = <16>;
- };
+ sdc2_cmd: sdc2-cmd-state {
+ pins = "sdc2_cmd";
+ bias-pull-up;
+ drive-strength = <16>;
};
- sdc2_data: sdc2-data {
- pinconf {
- pins = "sdc2_data";
- bias-pull-up;
- drive-strength = <16>;
- };
+ sdc2_data: sdc2-data-state {
+ pins = "sdc2_data";
+ bias-pull-up;
+ drive-strength = <16>;
};
- sd_card_det_n: sd-card-det-n {
- pinmux {
- pins = "gpio126";
- function = "gpio";
- };
-
- pinconf {
- pins = "gpio126";
- bias-pull-up;
- };
+ sd_card_det_n: sd-card-det-n-state {
+ pins = "gpio126";
+ function = "gpio";
+ bias-pull-up;
};
};
diff --git a/arch/arm64/boot/dts/qcom/sdm845-lg-judyln.dts b/arch/arm64/boot/dts/qcom/sdm845-lg-judyln.dts
index 7d967a104b3e..a12723310c8b 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-lg-judyln.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-lg-judyln.dts
@@ -58,7 +58,7 @@ &mss_pil {
};
&tlmm {
- thinq_key_default: thinq-key-default {
+ thinq_key_default: thinq-key-default-state {
pins = "gpio89";
function = "gpio";
diff --git a/arch/arm64/boot/dts/qcom/sdm845-mtp.dts b/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
index de2d10e0315a..7c5478b71f8b 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
@@ -719,68 +719,49 @@ &wifi {
/* PINCTRL - additions to nodes defined in sdm845.dtsi */
&qup_i2c10_default {
- pinconf {
- pins = "gpio55", "gpio56";
- drive-strength = <2>;
- bias-disable;
- };
+ drive-strength = <2>;
+ bias-disable;
};
-&qup_uart9_default {
- pinconf-tx {
- pins = "gpio4";
- drive-strength = <2>;
- bias-disable;
- };
+&qup_uart9_rx {
+ drive-strength = <2>;
+ bias-pull-up;
+};
- pinconf-rx {
- pins = "gpio5";
- drive-strength = <2>;
- bias-pull-up;
- };
+&qup_uart9_tx {
+ drive-strength = <2>;
+ bias-disable;
};
&tlmm {
gpio-reserved-ranges = <0 4>, <81 4>;
- sdc2_clk: sdc2-clk {
- pinconf {
- pins = "sdc2_clk";
- bias-disable;
+ sdc2_clk: sdc2-clk-state {
+ pins = "sdc2_clk";
+ bias-disable;
- /*
- * It seems that mmc_test reports errors if drive
- * strength is not 16 on clk, cmd, and data pins.
- */
- drive-strength = <16>;
- };
+ /*
+ * It seems that mmc_test reports errors if drive
+ * strength is not 16 on clk, cmd, and data pins.
+ */
+ drive-strength = <16>;
};
- sdc2_cmd: sdc2-cmd {
- pinconf {
- pins = "sdc2_cmd";
- bias-pull-up;
- drive-strength = <16>;
- };
+ sdc2_cmd: sdc2-cmd-state {
+ pins = "sdc2_cmd";
+ bias-pull-up;
+ drive-strength = <16>;
};
- sdc2_data: sdc2-data {
- pinconf {
- pins = "sdc2_data";
- bias-pull-up;
- drive-strength = <16>;
- };
+ sdc2_data: sdc2-data-state {
+ pins = "sdc2_data";
+ bias-pull-up;
+ drive-strength = <16>;
};
- sd_card_det_n: sd-card-det-n {
- pinmux {
- pins = "gpio126";
- function = "gpio";
- };
-
- pinconf {
- pins = "gpio126";
- bias-pull-up;
- };
+ sd_card_det_n: sd-card-det-n-state {
+ pins = "gpio126";
+ function = "gpio";
+ bias-pull-up;
};
};
diff --git a/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi b/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi
index 42cf4dd5ea28..738c9d0b322f 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi
@@ -474,35 +474,24 @@ &qupv3_id_0 {
status = "okay";
};
-&qup_i2c12_default {
- mux {
- pins = "gpio49", "gpio50";
- function = "qup12";
- drive-strength = <2>;
- bias-disable;
- };
+&qup_i2c10_default {
+ drive-strength = <2>;
+ bias-disable;
};
-&qup_i2c10_default {
- pinconf {
- pins = "gpio55", "gpio56";
- drive-strength = <2>;
- bias-disable;
- };
+&qup_i2c12_default {
+ drive-strength = <2>;
+ bias-disable;
};
-&qup_uart9_default {
- pinconf-tx {
- pins = "gpio4";
- drive-strength = <2>;
- bias-disable;
- };
+&qup_uart9_rx {
+ drive-strength = <2>;
+ bias-pull-up;
+};
- pinconf-rx {
- pins = "gpio5";
- drive-strength = <2>;
- bias-pull-up;
- };
+&qup_uart9_tx {
+ drive-strength = <2>;
+ bias-disable;
};
&uart6 {
@@ -588,51 +577,41 @@ &usb_1_hsphy {
&tlmm {
gpio-reserved-ranges = <0 4>, <81 4>;
- tri_state_key_default: tri_state_key_default {
- mux {
- pins = "gpio40", "gpio42", "gpio26";
- function = "gpio";
- drive-strength = <2>;
- bias-disable;
- };
+ tri_state_key_default: tri-state-key-default-state {
+ pins = "gpio40", "gpio42", "gpio26";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
};
- ts_default_pins: ts-int {
- mux {
- pins = "gpio99", "gpio125";
- function = "gpio";
- drive-strength = <16>;
- bias-pull-up;
- };
+ ts_default_pins: ts-int-state {
+ pins = "gpio99", "gpio125";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-pull-up;
};
- panel_reset_pins: panel-reset {
- mux {
- pins = "gpio6", "gpio25", "gpio26";
- function = "gpio";
- drive-strength = <8>;
- bias-disable;
- };
+ panel_reset_pins: panel-reset-state {
+ pins = "gpio6", "gpio25", "gpio26";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
};
- panel_te_pin: panel-te {
- mux {
- pins = "gpio10";
- function = "mdp_vsync";
- drive-strength = <2>;
- bias-disable;
- input-enable;
- };
+ panel_te_pin: panel-te-state {
+ pins = "gpio10";
+ function = "mdp_vsync";
+ drive-strength = <2>;
+ bias-disable;
+ input-enable;
};
- panel_esd_pin: panel-esd {
- mux {
- pins = "gpio30";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-down;
- input-enable;
- };
+ panel_esd_pin: panel-esd-state {
+ pins = "gpio30";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ input-enable;
};
};
diff --git a/arch/arm64/boot/dts/qcom/sdm845-shift-axolotl.dts b/arch/arm64/boot/dts/qcom/sdm845-shift-axolotl.dts
index bb77ccfdc68c..563557eb1ada 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-shift-axolotl.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-shift-axolotl.dts
@@ -559,18 +559,14 @@ led@5 {
};
};
-&qup_uart9_default {
- pinconf-rx {
- pins = "gpio5";
- drive-strength = <2>;
- bias-pull-up;
- };
+&qup_uart9_rx {
+ drive-strength = <2>;
+ bias-pull-up;
+};
- pinconf-tx {
- pins = "gpio4";
- drive-strength = <2>;
- bias-disable;
- };
+&qup_uart9_tx {
+ drive-strength = <2>;
+ bias-disable;
};
&qupv3_id_0 {
@@ -584,110 +580,62 @@ &qupv3_id_1 {
&tlmm {
gpio-reserved-ranges = <0 4>, <81 4>;
- sde_dsi_active: sde-dsi-active {
- mux {
- pins = "gpio6", "gpio11";
- function = "gpio";
- };
-
- config {
- pins = "gpio6", "gpio11";
- drive-strength = <8>;
- bias-disable;
- };
+ sde_dsi_active: sde-dsi-active-state {
+ pins = "gpio6", "gpio11";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
};
- sde_dsi_suspend: sde-dsi-suspend {
- mux {
- pins = "gpio6", "gpio11";
- function = "gpio";
- };
-
- config {
- pins = "gpio6", "gpio11";
- drive-strength = <2>;
- bias-pull-down;
- };
+ sde_dsi_suspend: sde-dsi-suspend-state {
+ pins = "gpio6", "gpio11";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
};
- sde_te_active: sde-te-active {
- mux {
- pins = "gpio10";
- function = "mdp_vsync";
- };
-
- config {
- pins = "gpio10";
- drive-strength = <2>;
- bias-pull-down;
- };
+ sde_te_active: sde-te-active-state {
+ pins = "gpio10";
+ function = "mdp_vsync";
+ drive-strength = <2>;
+ bias-pull-down;
};
- sde_te_suspend: sde-te-suspend {
- mux {
- pins = "gpio10";
- function = "mdp_vsync";
- };
-
- config {
- pins = "gpio10";
- drive-strength = <2>;
- bias-pull-down;
- };
+ sde_te_suspend: sde-te-suspend-state {
+ pins = "gpio10";
+ function = "mdp_vsync";
+ drive-strength = <2>;
+ bias-pull-down;
};
- ts_int_active: ts-int-active {
- mux {
- pins = "gpio125";
- function = "gpio";
- };
-
- config {
- pins = "gpio125";
- drive-strength = <8>;
- bias-pull-up;
- input-enable;
- };
+ ts_int_active: ts-int-active-state {
+ pins = "gpio125";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-up;
+ input-enable;
};
- ts_int_suspend: ts-int-suspend {
- mux {
- pins = "gpio125";
- function = "gpio";
- };
-
- config {
- pins = "gpio125";
- drive-strength = <2>;
- bias-pull-down;
- input-enable;
- };
+ ts_int_suspend: ts-int-suspend-state {
+ pins = "gpio125";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ input-enable;
};
- ts_reset_active: ts-reset-active {
- mux {
- pins = "gpio99";
- function = "gpio";
- };
-
- config {
- pins = "gpio99";
- drive-strength = <8>;
- bias-pull-up;
- };
+ ts_reset_active: ts-reset-active-state {
+ pins = "gpio99";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-up;
};
- ts_reset_suspend: ts-reset-suspend {
- mux {
- pins = "gpio99";
- function = "gpio";
- };
-
- config {
- pins = "gpio99";
- drive-strength = <2>;
- bias-pull-down;
- };
+ ts_reset_suspend: ts-reset-suspend-state {
+ pins = "gpio99";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
};
};
diff --git a/arch/arm64/boot/dts/qcom/sdm845-sony-xperia-tama.dtsi b/arch/arm64/boot/dts/qcom/sdm845-sony-xperia-tama.dtsi
index 51ee42e3c995..3a920275dda3 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-sony-xperia-tama.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845-sony-xperia-tama.dtsi
@@ -383,19 +383,19 @@ &tlmm {
gpio-reserved-ranges = <0 4>, <81 4>;
sdc2_default_state: sdc2-default-state {
- clk {
+ clk-pins {
pins = "sdc2_clk";
drive-strength = <16>;
bias-disable;
};
- cmd {
+ cmd-pins {
pins = "sdc2_cmd";
drive-strength = <10>;
bias-pull-up;
};
- data {
+ data-pins {
pins = "sdc2_data";
drive-strength = <10>;
bias-pull-up;
diff --git a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-common.dtsi b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-common.dtsi
index eb6b2b676eca..a21c52d3902f 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-common.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-common.dtsi
@@ -445,33 +445,33 @@ codec {
&tlmm {
gpio-reserved-ranges = <0 4>, <81 4>;
- sdc2_default_state: sdc2-default {
- clk {
+ sdc2_default_state: sdc2-default-state {
+ clk-pins {
pins = "sdc2_clk";
bias-disable;
drive-strength = <16>;
};
- cmd {
+ cmd-pins {
pins = "sdc2_cmd";
bias-pull-up;
drive-strength = <10>;
};
- data {
+ data-pins {
pins = "sdc2_data";
bias-pull-up;
drive-strength = <10>;
};
};
- sdc2_card_det_n: sd-card-det-n {
+ sdc2_card_det_n: sd-card-det-n-state {
pins = "gpio126";
function = "gpio";
bias-pull-up;
};
- wcd_intr_default: wcd_intr_default {
+ wcd_intr_default: wcd-intr-default-state {
pins = <54>;
function = "gpio";
diff --git a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-polaris.dts b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-polaris.dts
index fc189f7caaa4..cc5924e53305 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-polaris.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-polaris.dts
@@ -573,24 +573,21 @@ &qupv3_id_1 {
};
&qup_i2c14_default {
- pinconf {
- pins = "gpio33", "gpio34";
- drive-strength = <2>;
- bias-disable;
- };
+ drive-strength = <2>;
+ bias-disable;
};
&tlmm {
gpio-reserved-ranges = <0 4>, <81 4>;
- ts_reset_default: ts-reset-default {
+ ts_reset_default: ts-reset-default-state {
pins = "gpio99";
function = "gpio";
drive-strength = <16>;
output-high;
};
- ts_int_default: ts-int-default {
+ ts_int_default: ts-int-default-state {
pins = "gpio125";
function = "gpio";
bias-pull-down;
@@ -598,14 +595,14 @@ ts_int_default: ts-int-default {
input-enable;
};
- ts_reset_sleep: ts-reset-sleep {
+ ts_reset_sleep: ts-reset-sleep-state {
pins = "gpio99";
function = "gpio";
bias-disable;
drive-strength = <2>;
};
- ts_int_sleep: ts-int-sleep {
+ ts_int_sleep: ts-int-sleep-state {
pins = "gpio125";
function = "gpio";
bias-pull-down;
@@ -613,21 +610,21 @@ ts_int_sleep: ts-int-sleep {
input-enable;
};
- sde_dsi_active: sde-dsi-active {
+ sde_dsi_active: sde-dsi-active-state {
pins = "gpio6", "gpio10";
function = "gpio";
drive-strength = <8>;
bias-disable;
};
- sde_dsi_suspend: sde-dsi-suspend {
+ sde_dsi_suspend: sde-dsi-suspend-state {
pins = "gpio6", "gpio10";
function = "gpio";
drive-strength = <2>;
bias-pull-down;
};
- wcd_intr_default: wcd-intr-default {
+ wcd_intr_default: wcd-intr-default-state {
pins = "gpio54";
function = "gpio";
input-enable;
diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi
index 1a257f672887..598d0c523db5 100644
--- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
@@ -2641,7 +2641,7 @@ tlmm: pinctrl@3400000 {
gpio-ranges = <&tlmm 0 0 151>;
wakeup-parent = <&pdc_intc>;
- cci0_default: cci0-default {
+ cci0_default: cci0-default-state {
/* SDA, SCL */
pins = "gpio17", "gpio18";
function = "cci_i2c";
@@ -2650,7 +2650,7 @@ cci0_default: cci0-default {
drive-strength = <2>; /* 2 mA */
};
- cci0_sleep: cci0-sleep {
+ cci0_sleep: cci0-sleep-state {
/* SDA, SCL */
pins = "gpio17", "gpio18";
function = "cci_i2c";
@@ -2659,7 +2659,7 @@ cci0_sleep: cci0-sleep {
bias-pull-down;
};
- cci1_default: cci1-default {
+ cci1_default: cci1-default-state {
/* SDA, SCL */
pins = "gpio19", "gpio20";
function = "cci_i2c";
@@ -2668,7 +2668,7 @@ cci1_default: cci1-default {
drive-strength = <2>; /* 2 mA */
};
- cci1_sleep: cci1-sleep {
+ cci1_sleep: cci1-sleep-state {
/* SDA, SCL */
pins = "gpio19", "gpio20";
function = "cci_i2c";
@@ -2677,556 +2677,476 @@ cci1_sleep: cci1-sleep {
bias-pull-down;
};
- qspi_clk: qspi-clk {
- pinmux {
- pins = "gpio95";
- function = "qspi_clk";
- };
+ qspi_clk: qspi-clk-state {
+ pins = "gpio95";
+ function = "qspi_clk";
};
- qspi_cs0: qspi-cs0 {
- pinmux {
- pins = "gpio90";
- function = "qspi_cs";
- };
+ qspi_cs0: qspi-cs0-state {
+ pins = "gpio90";
+ function = "qspi_cs";
};
- qspi_cs1: qspi-cs1 {
- pinmux {
- pins = "gpio89";
- function = "qspi_cs";
- };
+ qspi_cs1: qspi-cs1-state {
+ pins = "gpio89";
+ function = "qspi_cs";
};
- qspi_data01: qspi-data01 {
- pinmux-data {
- pins = "gpio91", "gpio92";
- function = "qspi_data";
- };
+ qspi_data01: qspi-data01-state {
+ pins = "gpio91", "gpio92";
+ function = "qspi_data";
};
- qspi_data12: qspi-data12 {
- pinmux-data {
- pins = "gpio93", "gpio94";
- function = "qspi_data";
- };
+ qspi_data12: qspi-data12-state {
+ pins = "gpio93", "gpio94";
+ function = "qspi_data";
};
- qup_i2c0_default: qup-i2c0-default {
- pinmux {
- pins = "gpio0", "gpio1";
- function = "qup0";
- };
+ qup_i2c0_default: qup-i2c0-default-state {
+ pins = "gpio0", "gpio1";
+ function = "qup0";
};
- qup_i2c1_default: qup-i2c1-default {
- pinmux {
- pins = "gpio17", "gpio18";
- function = "qup1";
- };
+ qup_i2c1_default: qup-i2c1-default-state {
+ pins = "gpio17", "gpio18";
+ function = "qup1";
};
- qup_i2c2_default: qup-i2c2-default {
- pinmux {
- pins = "gpio27", "gpio28";
- function = "qup2";
- };
+ qup_i2c2_default: qup-i2c2-default-state {
+ pins = "gpio27", "gpio28";
+ function = "qup2";
};
- qup_i2c3_default: qup-i2c3-default {
- pinmux {
- pins = "gpio41", "gpio42";
- function = "qup3";
- };
+ qup_i2c3_default: qup-i2c3-default-state {
+ pins = "gpio41", "gpio42";
+ function = "qup3";
};
- qup_i2c4_default: qup-i2c4-default {
- pinmux {
- pins = "gpio89", "gpio90";
- function = "qup4";
- };
+ qup_i2c4_default: qup-i2c4-default-state {
+ pins = "gpio89", "gpio90";
+ function = "qup4";
};
- qup_i2c5_default: qup-i2c5-default {
- pinmux {
- pins = "gpio85", "gpio86";
- function = "qup5";
- };
+ qup_i2c5_default: qup-i2c5-default-state {
+ pins = "gpio85", "gpio86";
+ function = "qup5";
};
- qup_i2c6_default: qup-i2c6-default {
- pinmux {
- pins = "gpio45", "gpio46";
- function = "qup6";
- };
+ qup_i2c6_default: qup-i2c6-default-state {
+ pins = "gpio45", "gpio46";
+ function = "qup6";
};
- qup_i2c7_default: qup-i2c7-default {
- pinmux {
- pins = "gpio93", "gpio94";
- function = "qup7";
- };
+ qup_i2c7_default: qup-i2c7-default-state {
+ pins = "gpio93", "gpio94";
+ function = "qup7";
};
- qup_i2c8_default: qup-i2c8-default {
- pinmux {
- pins = "gpio65", "gpio66";
- function = "qup8";
- };
+ qup_i2c8_default: qup-i2c8-default-state {
+ pins = "gpio65", "gpio66";
+ function = "qup8";
};
- qup_i2c9_default: qup-i2c9-default {
- pinmux {
- pins = "gpio6", "gpio7";
- function = "qup9";
- };
+ qup_i2c9_default: qup-i2c9-default-state {
+ pins = "gpio6", "gpio7";
+ function = "qup9";
};
- qup_i2c10_default: qup-i2c10-default {
- pinmux {
- pins = "gpio55", "gpio56";
- function = "qup10";
- };
+ qup_i2c10_default: qup-i2c10-default-state {
+ pins = "gpio55", "gpio56";
+ function = "qup10";
};
- qup_i2c11_default: qup-i2c11-default {
- pinmux {
- pins = "gpio31", "gpio32";
- function = "qup11";
- };
+ qup_i2c11_default: qup-i2c11-default-state {
+ pins = "gpio31", "gpio32";
+ function = "qup11";
};
- qup_i2c12_default: qup-i2c12-default {
- pinmux {
- pins = "gpio49", "gpio50";
- function = "qup12";
- };
+ qup_i2c12_default: qup-i2c12-default-state {
+ pins = "gpio49", "gpio50";
+ function = "qup12";
};
- qup_i2c13_default: qup-i2c13-default {
- pinmux {
- pins = "gpio105", "gpio106";
- function = "qup13";
- };
+ qup_i2c13_default: qup-i2c13-default-state {
+ pins = "gpio105", "gpio106";
+ function = "qup13";
};
- qup_i2c14_default: qup-i2c14-default {
- pinmux {
- pins = "gpio33", "gpio34";
- function = "qup14";
- };
+ qup_i2c14_default: qup-i2c14-default-state {
+ pins = "gpio33", "gpio34";
+ function = "qup14";
};
- qup_i2c15_default: qup-i2c15-default {
- pinmux {
- pins = "gpio81", "gpio82";
- function = "qup15";
- };
+ qup_i2c15_default: qup-i2c15-default-state {
+ pins = "gpio81", "gpio82";
+ function = "qup15";
};
- qup_spi0_default: qup-spi0-default {
- pinmux {
- pins = "gpio0", "gpio1",
- "gpio2", "gpio3";
- function = "qup0";
- };
+ qup_spi0_default: qup-spi0-default-state {
+ pins = "gpio0", "gpio1", "gpio2", "gpio3";
+ function = "qup0";
+ drive-strength = <6>;
+ bias-disable;
+ };
- config {
- pins = "gpio0", "gpio1",
- "gpio2", "gpio3";
- drive-strength = <6>;
- bias-disable;
- };
+ qup_spi1_default: qup-spi1-default-state {
+ pins = "gpio17", "gpio18", "gpio19", "gpio20";
+ function = "qup1";
};
- qup_spi1_default: qup-spi1-default {
- pinmux {
- pins = "gpio17", "gpio18",
- "gpio19", "gpio20";
- function = "qup1";
- };
+ qup_spi2_default: qup-spi2-default-state {
+ pins = "gpio27", "gpio28", "gpio29", "gpio30";
+ function = "qup2";
};
- qup_spi2_default: qup-spi2-default {
- pinmux {
- pins = "gpio27", "gpio28",
- "gpio29", "gpio30";
- function = "qup2";
- };
+ qup_spi3_default: qup-spi3-default-state {
+ pins = "gpio41", "gpio42", "gpio43", "gpio44";
+ function = "qup3";
};
- qup_spi3_default: qup-spi3-default {
- pinmux {
- pins = "gpio41", "gpio42",
- "gpio43", "gpio44";
- function = "qup3";
- };
+ qup_spi4_default: qup-spi4-default-state {
+ pins = "gpio89", "gpio90", "gpio91", "gpio92";
+ function = "qup4";
};
- qup_spi4_default: qup-spi4-default {
- pinmux {
- pins = "gpio89", "gpio90",
- "gpio91", "gpio92";
- function = "qup4";
- };
+ qup_spi5_default: qup-spi5-default-state {
+ pins = "gpio85", "gpio86", "gpio87", "gpio88";
+ function = "qup5";
};
- qup_spi5_default: qup-spi5-default {
- pinmux {
- pins = "gpio85", "gpio86",
- "gpio87", "gpio88";
- function = "qup5";
- };
+ qup_spi6_default: qup-spi6-default-state {
+ pins = "gpio45", "gpio46", "gpio47", "gpio48";
+ function = "qup6";
};
- qup_spi6_default: qup-spi6-default {
- pinmux {
- pins = "gpio45", "gpio46",
- "gpio47", "gpio48";
- function = "qup6";
- };
+ qup_spi7_default: qup-spi7-default-state {
+ pins = "gpio93", "gpio94", "gpio95", "gpio96";
+ function = "qup7";
};
- qup_spi7_default: qup-spi7-default {
- pinmux {
- pins = "gpio93", "gpio94",
- "gpio95", "gpio96";
- function = "qup7";
- };
+ qup_spi8_default: qup-spi8-default-state {
+ pins = "gpio65", "gpio66", "gpio67", "gpio68";
+ function = "qup8";
};
- qup_spi8_default: qup-spi8-default {
- pinmux {
- pins = "gpio65", "gpio66",
- "gpio67", "gpio68";
- function = "qup8";
- };
+ qup_spi9_default: qup-spi9-default-state {
+ pins = "gpio6", "gpio7", "gpio4", "gpio5";
+ function = "qup9";
};
- qup_spi9_default: qup-spi9-default {
- pinmux {
- pins = "gpio6", "gpio7",
- "gpio4", "gpio5";
- function = "qup9";
- };
+ qup_spi10_default: qup-spi10-default-state {
+ pins = "gpio55", "gpio56", "gpio53", "gpio54";
+ function = "qup10";
};
- qup_spi10_default: qup-spi10-default {
- pinmux {
- pins = "gpio55", "gpio56",
- "gpio53", "gpio54";
- function = "qup10";
- };
+ qup_spi11_default: qup-spi11-default-state {
+ pins = "gpio31", "gpio32", "gpio33", "gpio34";
+ function = "qup11";
};
- qup_spi11_default: qup-spi11-default {
- pinmux {
- pins = "gpio31", "gpio32",
- "gpio33", "gpio34";
- function = "qup11";
- };
+ qup_spi12_default: qup-spi12-default-state {
+ pins = "gpio49", "gpio50", "gpio51", "gpio52";
+ function = "qup12";
};
- qup_spi12_default: qup-spi12-default {
- pinmux {
- pins = "gpio49", "gpio50",
- "gpio51", "gpio52";
- function = "qup12";
- };
+ qup_spi13_default: qup-spi13-default-state {
+ pins = "gpio105", "gpio106", "gpio107", "gpio108";
+ function = "qup13";
};
- qup_spi13_default: qup-spi13-default {
- pinmux {
- pins = "gpio105", "gpio106",
- "gpio107", "gpio108";
- function = "qup13";
- };
+ qup_spi14_default: qup-spi14-default-state {
+ pins = "gpio33", "gpio34", "gpio31", "gpio32";
+ function = "qup14";
};
- qup_spi14_default: qup-spi14-default {
- pinmux {
- pins = "gpio33", "gpio34",
- "gpio31", "gpio32";
- function = "qup14";
- };
+ qup_spi15_default: qup-spi15-default-state {
+ pins = "gpio81", "gpio82", "gpio83", "gpio84";
+ function = "qup15";
};
- qup_spi15_default: qup-spi15-default {
- pinmux {
- pins = "gpio81", "gpio82",
- "gpio83", "gpio84";
- function = "qup15";
+ qup_uart0_default: qup-uart0-default-state {
+ qup_uart0_tx: tx-pins {
+ pins = "gpio2";
+ function = "qup0";
};
- };
- qup_uart0_default: qup-uart0-default {
- pinmux {
- pins = "gpio2", "gpio3";
+ qup_uart0_rx: rx-pins {
+ pins = "gpio3";
function = "qup0";
};
};
- qup_uart1_default: qup-uart1-default {
- pinmux {
- pins = "gpio19", "gpio20";
+ qup_uart1_default: qup-uart1-default-state {
+ qup_uart1_tx: tx-pins {
+ pins = "gpio19";
+ function = "qup1";
+ };
+
+ qup_uart1_rx: rx-pins {
+ pins = "gpio20";
function = "qup1";
};
};
- qup_uart2_default: qup-uart2-default {
- pinmux {
- pins = "gpio29", "gpio30";
+ qup_uart2_default: qup-uart2-default-state {
+ qup_uart2_tx: tx-pins {
+ pins = "gpio29";
+ function = "qup2";
+ };
+
+ qup_uart2_rx: rx-pins {
+ pins = "gpio30";
function = "qup2";
};
};
- qup_uart3_default: qup-uart3-default {
- pinmux {
- pins = "gpio43", "gpio44";
+ qup_uart3_default: qup-uart3-default-state {
+ qup_uart3_tx: tx-pins {
+ pins = "gpio43";
+ function = "qup3";
+ };
+
+ qup_uart3_rx: rx-pins {
+ pins = "gpio44";
function = "qup3";
};
};
- qup_uart4_default: qup-uart4-default {
- pinmux {
- pins = "gpio91", "gpio92";
+ qup_uart4_default: qup-uart4-default-state {
+ qup_uart4_tx: tx-pins {
+ pins = "gpio91";
+ function = "qup4";
+ };
+
+ qup_uart4_rx: rx-pins {
+ pins = "gpio92";
function = "qup4";
};
};
- qup_uart5_default: qup-uart5-default {
- pinmux {
- pins = "gpio87", "gpio88";
+ qup_uart5_default: qup-uart5-default-state {
+ qup_uart5_tx: tx-pins {
+ pins = "gpio87";
+ function = "qup5";
+ };
+
+ qup_uart5_rx: rx-pins {
+ pins = "gpio88";
function = "qup5";
};
};
- qup_uart6_default: qup-uart6-default {
- pinmux {
- pins = "gpio47", "gpio48";
+ qup_uart6_default: qup-uart6-default-state {
+ qup_uart6_tx: tx-pins {
+ pins = "gpio47";
+ function = "qup6";
+ };
+
+ qup_uart6_rx: rx-pins {
+ pins = "gpio48";
function = "qup6";
};
};
qup_uart6_4pin: qup-uart6-4pin-state {
-
- cts-pins {
+ qup_uart6_4pin_cts: cts-pins {
pins = "gpio45";
function = "qup6";
- bias-pull-down;
};
- rts-tx-pins {
+ qup_uart6_4pin_rts_tx: rts-tx-pins {
pins = "gpio46", "gpio47";
function = "qup6";
- drive-strength = <2>;
- bias-disable;
};
- rx-pins {
+ qup_uart6_4pin_rx: rx-pins {
pins = "gpio48";
function = "qup6";
- bias-pull-up;
};
};
- qup_uart7_default: qup-uart7-default {
- pinmux {
- pins = "gpio95", "gpio96";
+ qup_uart7_default: qup-uart7-default-state {
+ qup_uart7_tx: tx-pins {
+ pins = "gpio95";
function = "qup7";
};
- };
- qup_uart8_default: qup-uart8-default {
- pinmux {
- pins = "gpio67", "gpio68";
- function = "qup8";
- };
- };
-
- qup_uart9_default: qup-uart9-default {
- pinmux {
- pins = "gpio4", "gpio5";
- function = "qup9";
+ qup_uart7_rx: rx-pins {
+ pins = "gpio96";
+ function = "qup7";
};
};
- qup_uart10_default: qup-uart10-default {
- pinmux {
- pins = "gpio53", "gpio54";
- function = "qup10";
+ qup_uart8_default: qup-uart8-default-state {
+ qup_uart8_tx: tx-pins {
+ pins = "gpio67";
+ function = "qup8";
};
- };
- qup_uart11_default: qup-uart11-default {
- pinmux {
- pins = "gpio33", "gpio34";
- function = "qup11";
+ qup_uart8_rx: rx-pins {
+ pins = "gpio68";
+ function = "qup8";
};
};
- qup_uart12_default: qup-uart12-default {
- pinmux {
- pins = "gpio51", "gpio52";
- function = "qup12";
+ qup_uart9_default: qup-uart9-default-state {
+ qup_uart9_tx: tx-pins {
+ pins = "gpio4";
+ function = "qup9";
};
- };
- qup_uart13_default: qup-uart13-default {
- pinmux {
- pins = "gpio107", "gpio108";
- function = "qup13";
+ qup_uart9_rx: rx-pins {
+ pins = "gpio5";
+ function = "qup9";
};
};
- qup_uart14_default: qup-uart14-default {
- pinmux {
- pins = "gpio31", "gpio32";
- function = "qup14";
+ qup_uart10_default: qup-uart10-default-state {
+ qup_uart10_tx: tx-pins {
+ pins = "gpio53";
+ function = "qup10";
};
- };
- qup_uart15_default: qup-uart15-default {
- pinmux {
- pins = "gpio83", "gpio84";
- function = "qup15";
+ qup_uart10_rx: rx-pins {
+ pins = "gpio54";
+ function = "qup10";
};
};
- quat_mi2s_sleep: quat_mi2s_sleep {
- mux {
- pins = "gpio58", "gpio59";
- function = "gpio";
+ qup_uart11_default: qup-uart11-default-state {
+ qup_uart11_tx: tx-pins {
+ pins = "gpio33";
+ function = "qup11";
};
- config {
- pins = "gpio58", "gpio59";
- drive-strength = <2>;
- bias-pull-down;
- input-enable;
+ qup_uart11_rx: rx-pins {
+ pins = "gpio34";
+ function = "qup11";
};
};
- quat_mi2s_active: quat_mi2s_active {
- mux {
- pins = "gpio58", "gpio59";
- function = "qua_mi2s";
+ qup_uart12_default: qup-uart12-default-state {
+ qup_uart12_tx: tx-pins {
+ pins = "gpio51";
+ function = "qup0";
};
- config {
- pins = "gpio58", "gpio59";
- drive-strength = <8>;
- bias-disable;
- output-high;
+ qup_uart12_rx: rx-pins {
+ pins = "gpio52";
+ function = "qup0";
};
};
- quat_mi2s_sd0_sleep: quat_mi2s_sd0_sleep {
- mux {
- pins = "gpio60";
- function = "gpio";
+ qup_uart13_default: qup-uart13-default-state {
+ qup_uart13_tx: tx-pins {
+ pins = "gpio107";
+ function = "qup13";
};
- config {
- pins = "gpio60";
- drive-strength = <2>;
- bias-pull-down;
- input-enable;
+ qup_uart13_rx: rx-pins {
+ pins = "gpio108";
+ function = "qup13";
};
};
- quat_mi2s_sd0_active: quat_mi2s_sd0_active {
- mux {
- pins = "gpio60";
- function = "qua_mi2s";
+ qup_uart14_default: qup-uart14-default-state {
+ qup_uart14_tx: tx-pins {
+ pins = "gpio31";
+ function = "qup14";
};
- config {
- pins = "gpio60";
- drive-strength = <8>;
- bias-disable;
+ qup_uart14_rx: rx-pins {
+ pins = "gpio32";
+ function = "qup14";
};
};
- quat_mi2s_sd1_sleep: quat_mi2s_sd1_sleep {
- mux {
- pins = "gpio61";
- function = "gpio";
+ qup_uart15_default: qup-uart15-default-state {
+ qup_uart15_tx: tx-pins {
+ pins = "gpio83";
+ function = "qup15";
};
- config {
- pins = "gpio61";
- drive-strength = <2>;
- bias-pull-down;
- input-enable;
+ qup_uart15_rx: rx-pins {
+ pins = "gpio84";
+ function = "qup15";
};
};
- quat_mi2s_sd1_active: quat_mi2s_sd1_active {
- mux {
- pins = "gpio61";
- function = "qua_mi2s";
- };
+ quat_mi2s_sleep: quat-mi2s-sleep-state {
+ pins = "gpio58", "gpio59";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ input-enable;
+ };
- config {
- pins = "gpio61";
- drive-strength = <8>;
- bias-disable;
- };
+ quat_mi2s_active: quat-mi2s-active-state {
+ pins = "gpio58", "gpio59";
+ function = "qua_mi2s";
+ drive-strength = <8>;
+ bias-disable;
+ output-high;
};
- quat_mi2s_sd2_sleep: quat_mi2s_sd2_sleep {
- mux {
- pins = "gpio62";
- function = "gpio";
- };
+ quat_mi2s_sd0_sleep: quat-mi2s-sd0-sleep-state {
+ pins = "gpio60";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ input-enable;
+ };
- config {
- pins = "gpio62";
- drive-strength = <2>;
- bias-pull-down;
- input-enable;
- };
+ quat_mi2s_sd0_active: quat-mi2s-sd0-active-state {
+ pins = "gpio60";
+ function = "qua_mi2s";
+ drive-strength = <8>;
+ bias-disable;
};
- quat_mi2s_sd2_active: quat_mi2s_sd2_active {
- mux {
- pins = "gpio62";
- function = "qua_mi2s";
- };
+ quat_mi2s_sd1_sleep: quat-mi2s-sd1-sleep-state {
+ pins = "gpio61";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ input-enable;
+ };
- config {
- pins = "gpio62";
- drive-strength = <8>;
- bias-disable;
- };
+ quat_mi2s_sd1_active: quat-mi2s-sd1-active-state {
+ pins = "gpio61";
+ function = "qua_mi2s";
+ drive-strength = <8>;
+ bias-disable;
};
- quat_mi2s_sd3_sleep: quat_mi2s_sd3_sleep {
- mux {
- pins = "gpio63";
- function = "gpio";
- };
+ quat_mi2s_sd2_sleep: quat-mi2s-sd2-sleep-state {
+ pins = "gpio62";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ input-enable;
+ };
- config {
- pins = "gpio63";
- drive-strength = <2>;
- bias-pull-down;
- input-enable;
- };
+ quat_mi2s_sd2_active: quat-mi2s-sd2-active-state {
+ pins = "gpio62";
+ function = "qua_mi2s";
+ drive-strength = <8>;
+ bias-disable;
};
- quat_mi2s_sd3_active: quat_mi2s_sd3_active {
- mux {
- pins = "gpio63";
- function = "qua_mi2s";
- };
+ quat_mi2s_sd3_sleep: quat-mi2s-sd3-sleep-state {
+ pins = "gpio63";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ input-enable;
+ };
- config {
- pins = "gpio63";
- drive-strength = <8>;
- bias-disable;
- };
+ quat_mi2s_sd3_active: quat-mi2s-sd3-active-state {
+ pins = "gpio63";
+ function = "qua_mi2s";
+ drive-strength = <8>;
+ bias-disable;
};
};
diff --git a/arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts b/arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts
index 0c375ec795b8..f2c8ddb93305 100644
--- a/arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts
+++ b/arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts
@@ -479,41 +479,26 @@ &mss_pil {
};
&qup_i2c10_default {
- pinconf {
- pins = "gpio55", "gpio56";
- drive-strength = <2>;
- bias-disable;
- };
+ drive-strength = <2>;
+ bias-disable;
};
&qup_i2c12_default {
- pinmux {
- drive-strength = <2>;
- bias-disable;
- };
+ drive-strength = <2>;
+ bias-disable;
};
-&qup_uart6_default {
- pinmux {
- pins = "gpio45", "gpio46", "gpio47", "gpio48";
- function = "qup6";
- };
-
- cts {
- pins = "gpio45";
- bias-pull-down;
- };
+&qup_uart6_4pin_cts {
+ bias-pull-down;
+};
- rts-tx {
- pins = "gpio46", "gpio47";
- drive-strength = <2>;
- bias-disable;
- };
+&qup_uart6_4pin_rts_tx {
+ drive-strength = <2>;
+ bias-disable;
+};
- rx {
- pins = "gpio48";
- bias-pull-up;
- };
+&qup_uart6_4pin_rx {
+ bias-pull-up;
};
&qupv3_id_0 {
@@ -621,13 +606,14 @@ codec {
&tlmm {
gpio-reserved-ranges = <0 4>, <81 4>;
- sn65dsi86_pin_active: sn65dsi86-enable {
+ sn65dsi86_pin_active: sn65dsi86-enable-state {
pins = "gpio96";
+ function = "gpio";
drive-strength = <2>;
bias-disable;
};
- i2c3_hid_active: i2c2-hid-active {
+ i2c3_hid_active: i2c2-hid-active-state {
pins = "gpio37";
function = "gpio";
@@ -636,7 +622,7 @@ i2c3_hid_active: i2c2-hid-active {
drive-strength = <2>;
};
- i2c5_hid_active: i2c5-hid-active {
+ i2c5_hid_active: i2c5-hid-active-state {
pins = "gpio125";
function = "gpio";
@@ -645,7 +631,7 @@ i2c5_hid_active: i2c5-hid-active {
drive-strength = <2>;
};
- i2c11_hid_active: i2c11-hid-active {
+ i2c11_hid_active: i2c11-hid-active-state {
pins = "gpio92";
function = "gpio";
@@ -654,7 +640,7 @@ i2c11_hid_active: i2c11-hid-active {
drive-strength = <2>;
};
- wcd_intr_default: wcd_intr_default {
+ wcd_intr_default: wcd-intr-default-state {
pins = "gpio54";
function = "gpio";
@@ -663,7 +649,7 @@ wcd_intr_default: wcd_intr_default {
drive-strength = <2>;
};
- lid_pin_active: lid-pin {
+ lid_pin_active: lid-pin-state {
pins = "gpio124";
function = "gpio";
@@ -671,7 +657,7 @@ lid_pin_active: lid-pin {
bias-disable;
};
- mode_pin_active: mode-pin {
+ mode_pin_active: mode-pin-state {
pins = "gpio95";
function = "gpio";
@@ -681,6 +667,8 @@ mode_pin_active: mode-pin {
};
&uart6 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart6_4pin>;
status = "okay";
bluetooth {
diff --git a/arch/arm64/boot/dts/qcom/sdm850-samsung-w737.dts b/arch/arm64/boot/dts/qcom/sdm850-samsung-w737.dts
index b712834a5d64..09fefa422c7c 100644
--- a/arch/arm64/boot/dts/qcom/sdm850-samsung-w737.dts
+++ b/arch/arm64/boot/dts/qcom/sdm850-samsung-w737.dts
@@ -399,49 +399,31 @@ &mss_pil {
};
&qup_i2c10_default {
- pinconf {
- pins = "gpio55", "gpio56";
- drive-strength = <2>;
- bias-disable;
- };
+ drive-strength = <2>;
+ bias-disable;
};
&qup_i2c11_default {
- pinconf {
- pins = "gpio31", "gpio32";
- drive-strength = <2>;
- bias-disable;
- };
+ drive-strength = <2>;
+ bias-disable;
};
&qup_i2c12_default {
- pinmux {
- drive-strength = <2>;
- bias-disable;
- };
+ drive-strength = <2>;
+ bias-disable;
};
-&qup_uart6_default {
- pinmux {
- pins = "gpio45", "gpio46", "gpio47", "gpio48";
- function = "qup6";
- };
-
- cts {
- pins = "gpio45";
- bias-pull-down;
- };
+&qup_uart6_4pin_cts {
+ bias-pull-down;
+};
- rts-tx {
- pins = "gpio46", "gpio47";
- drive-strength = <2>;
- bias-disable;
- };
+&qup_uart6_4pin_rts_tx {
+ drive-strength = <2>;
+ bias-disable;
+};
- rx {
- pins = "gpio48";
- bias-pull-up;
- };
+&qup_uart6_4pin_rx {
+ bias-pull-up;
};
&qupv3_id_0 {
@@ -549,59 +531,41 @@ codec {
&tlmm {
gpio-reserved-ranges = <0 6>, <85 4>;
- pen_irq_l: pen-irq-l {
- pinmux {
- pins = "gpio119";
- function = "gpio";
- };
-
- pinconf {
- pins = "gpio119";
- bias-disable;
- };
+ pen_irq_l: pen-irq-l-state {
+ pins = "gpio119";
+ function = "gpio";
+ bias-disable;
};
- pen_pdct_l: pen-pdct-l {
- pinmux {
- pins = "gpio124";
- function = "gpio";
- };
-
- pinconf {
- pins = "gpio124";
- bias-disable;
- drive-strength = <2>;
- output-high;
- };
+ pen_pdct_l: pen-pdct-l-state {
+ pins = "gpio124";
+ function = "gpio";
+ bias-disable;
+ drive-strength = <2>;
+ output-high;
};
- pen_rst_l: pen-rst-l {
- pinmux {
- pins = "gpio21";
- function = "gpio";
- };
-
- pinconf {
- pins = "gpio21";
- bias-disable;
- drive-strength = <2>;
-
- /*
- * The pen driver doesn't currently support
- * driving this reset line. By specifying
- * output-high here we're relying on the fact
- * that this pin has a default pulldown at boot
- * (which makes sure the pen was in reset if it
- * was powered) and then we set it high here to
- * take it out of reset. Better would be if the
- * pen driver could control this and we could
- * remove "output-high" here.
- */
- output-high;
- };
+ pen_rst_l: pen-rst-l-state {
+ pins = "gpio21";
+ function = "gpio";
+ bias-disable;
+ drive-strength = <2>;
+
+ /*
+ * The pen driver doesn't currently support
+ * driving this reset line. By specifying
+ * output-high here we're relying on the fact
+ * that this pin has a default pulldown at boot
+ * (which makes sure the pen was in reset if it
+ * was powered) and then we set it high here to
+ * take it out of reset. Better would be if the
+ * pen driver could control this and we could
+ * remove "output-high" here.
+ */
+ output-high;
};
- wcd_intr_default: wcd_intr_default {
+ wcd_intr_default: wcd-intr-default-state {
pins = "gpio54";
function = "gpio";
@@ -612,6 +576,8 @@ wcd_intr_default: wcd_intr_default {
};
&uart6 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart6_4pin>;
status = "okay";
bluetooth {
--
2.34.1
^ permalink raw reply related [flat|nested] 10+ messages in thread