[TESTPATCH] xhci: fix usb2 resume timing and races.

[TESTPATCH] xhci: fix usb2 resume timing and races.

[Mathias Nyman]

usb2 ports need to signal resume for 20ms before moving to U0 state.
Both device and host can initiate resume.

On host initated resume port is set to resume state, sleep 20ms,
and finally set port to U0 state.

On device initated resume a port status interrupt with a port in resume
state in issued. The interrupt handler tags a resume_done[port]
timestamp with current time + 20ms, and kick roothub timer.
Root hub timer requests for port status, finds the port in resume state,
checks if resume_done[port] timestamp passed, and set port to U0 state.

There are a few issues with this approach,
1. A host initated resume will also generate a resume event, the event
   handler will find the port in resume state, believe it's a device
   initated and act accordingly.

2. A port status request might cut the 20ms resume signalling short if a
   get_port_status request is handled during the 20ms host resume.
   The port will be found in resume state. The timestamp is not set leading
   to time_after_eq(jiffoes, timestamp) returning true, as timestamp = 0.
   get_port_status will proceed with moving the port to U0.

3. If an error, or anything else happends to the port during device
   initated 20ms resume signalling it will leave all device resume
   parameters hanging uncleared preventing further resume.

Fix this by using the existing resuming_ports bitfield to indicate if
resume signalling timing is taken care of.
Also check if the resume_done[port] is set  before using it in time
comparison. Also clear out any resume signalling related variables if port
is not in U0 or Resume state.

Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
---
 drivers/usb/host/xhci-hub.c  | 38 ++++++++++++++++++++++++++++++++++++--
 drivers/usb/host/xhci-ring.c |  3 ++-
 2 files changed, 38 insertions(+), 3 deletions(-)

diff --git a/drivers/usb/host/xhci-hub.c b/drivers/usb/host/xhci-hub.c
index 78241b5..c4f5e41 100644
--- a/drivers/usb/host/xhci-hub.c
+++ b/drivers/usb/host/xhci-hub.c
@@ -616,8 +616,30 @@ static u32 xhci_get_port_status(struct usb_hcd *hcd,
 		if ((raw_port_status & PORT_RESET) ||
 				!(raw_port_status & PORT_PE))
 			return 0xffffffff;
-		if (time_after_eq(jiffies,
-					bus_state->resume_done[wIndex])) {
+		/* did port event handler already start 20ms resume timing? */
+		if (!bus_state->resume_done[wIndex]) {
+			/* If not, maybe we are in a host initated resume? */
+			if (test_bit(wIndex, &bus_state->resuming_ports)) {
+				/* Host initated resume doesn't time the resume
+				 * signalling using resume_done[].
+				 * It manually sets RESUME state, sleeps 20ms
+				 * and sets U0 state. This should probably be
+				 * changed, but not right now, do nothing
+				 */
+			} else {
+				/* port resume was discovered now and here,
+				 * start resume timing
+				 */
+				unsigned long timeout = jiffies +
+					msecs_to_jiffies(USB_RESUME_TIMEOUT);
+
+				set_bit(wIndex, &bus_state->resuming_ports);
+				bus_state->resume_done[wIndex] = timeout;
+				mod_timer(&hcd->rh_timer, timeout);
+			}
+		/* Has resume been signalled for 20ms? yet? */
+		} else if (time_after_eq(jiffies,
+					 bus_state->resume_done[wIndex])) {
 			int time_left;
 
 			xhci_dbg(xhci, "Resume USB2 port %d\n",
@@ -665,6 +687,16 @@ static u32 xhci_get_port_status(struct usb_hcd *hcd,
 			status |= USB_PORT_STAT_SUSPEND;
 		}
 	}
+	/* Clear stale usb2 resume signalling variables in case port changed
+	 * state during 20ms resume signalling. For example on error
+	 */
+	if ((bus_state->resume_done[wIndex] ||
+	     test_bit(wIndex, &bus_state->resuming_ports) &&
+	     (raw_port_status & PORT_PLS_MASK) != XDEV_U3 &&
+	     (raw_port_status & PORT_PLS_MASK) != XDEV_RESUME)) {
+		bus_state->resume_done[wIndex] = 0;
+		clear_bit(wIndex, &bus_state->resuming_ports);
+	}
 	if ((raw_port_status & PORT_PLS_MASK) == XDEV_U0
 			&& (raw_port_status & PORT_POWER)
 			&& (bus_state->suspended_ports & (1 << wIndex))) {
@@ -995,6 +1027,7 @@ int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
 				if ((temp & PORT_PE) == 0)
 					goto error;
 
+				set_bit(wIndex, &bus_state->resuming_ports);
 				xhci_set_link_state(xhci, port_array, wIndex,
 							XDEV_RESUME);
 				spin_unlock_irqrestore(&xhci->lock, flags);
@@ -1002,6 +1035,7 @@ int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
 				spin_lock_irqsave(&xhci->lock, flags);
 				xhci_set_link_state(xhci, port_array, wIndex,
 							XDEV_U0);
+				clear_bit(wIndex, &bus_state->resuming_ports);
 			}
 			bus_state->port_c_suspend |= 1 << wIndex;
 
diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c
index 97ffe39..3743bb2 100644
--- a/drivers/usb/host/xhci-ring.c
+++ b/drivers/usb/host/xhci-ring.c
@@ -1583,7 +1583,8 @@ static void handle_port_status(struct xhci_hcd *xhci,
 			 */
 			bogus_port_status = true;
 			goto cleanup;
-		} else {
+		} else if (!test_bit(faked_port_index,
+				     &bus_state->resuming_ports)) {
 			xhci_dbg(xhci, "resume HS port %d\n", port_id);
 			bus_state->resume_done[faked_port_index] = jiffies +
 				msecs_to_jiffies(USB_RESUME_TIMEOUT);
-- 
1.9.1

Re: [TESTPATCH] xhci: fix usb2 resume timing and races.

[kbuild test robot]

[-- Attachment #1: Type: text/plain, Size: 1998 bytes --]

Hi Mathias,

[auto build test WARNING on: v4.4-rc1]
[cannot apply to: v4.4-rc3 v4.4-rc2 next-20151127]

url:    https://github.com/0day-ci/linux/commits/Mathias-Nyman/xhci-fix-usb2-resume-timing-and-races/20151130-231438
config: i386-randconfig-r0-201548 (attached as .config)
reproduce:
        # save the attached .config to linux build tree
        make ARCH=i386 

All warnings (new ones prefixed by >>):

   drivers/usb/host/xhci-hub.c: In function 'xhci_get_port_status':
>> drivers/usb/host/xhci-hub.c:812:52: warning: suggest parentheses around '&&' within '||' [-Wparentheses]
          (raw_port_status & PORT_PLS_MASK) != XDEV_U3 &&
                                                       ^

vim +812 drivers/usb/host/xhci-hub.c

   796				bus_state->suspended_ports &= ~(1 << wIndex);
   797			} else {
   798				/*
   799				 * The resume has been signaling for less than
   800				 * 20ms. Report the port status as SUSPEND,
   801				 * let the usbcore check port status again
   802				 * and clear resume signaling later.
   803				 */
   804				status |= USB_PORT_STAT_SUSPEND;
   805			}
   806		}
   807		/* Clear stale usb2 resume signalling variables in case port changed
   808		 * state during 20ms resume signalling. For example on error
   809		 */
   810		if ((bus_state->resume_done[wIndex] ||
   811		     test_bit(wIndex, &bus_state->resuming_ports) &&
 > 812		     (raw_port_status & PORT_PLS_MASK) != XDEV_U3 &&
   813		     (raw_port_status & PORT_PLS_MASK) != XDEV_RESUME)) {
   814			bus_state->resume_done[wIndex] = 0;
   815			clear_bit(wIndex, &bus_state->resuming_ports);
   816		}
   817		if ((raw_port_status & PORT_PLS_MASK) == XDEV_U0
   818				&& (raw_port_status & PORT_POWER)
   819				&& (bus_state->suspended_ports & (1 << wIndex))) {
   820			bus_state->suspended_ports &= ~(1 << wIndex);

---
0-DAY kernel test infrastructure                Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all                   Intel Corporation

[-- Attachment #2: .config.gz --]
[-- Type: application/octet-stream, Size: 23433 bytes --]

Re: [TESTPATCH] xhci: fix usb2 resume timing and races.

[Alan Stern]

On Mon, 30 Nov 2015, Mathias Nyman wrote:

> usb2 ports need to signal resume for 20ms before moving to U0 state.
> Both device and host can initiate resume.
> 
> On host initated resume port is set to resume state, sleep 20ms,
> and finally set port to U0 state.

That's an odd approach.  The assumption in usbcore is that the HCD will 
not sleep here.

> On device initated resume a port status interrupt with a port in resume
> state in issued. The interrupt handler tags a resume_done[port]
> timestamp with current time + 20ms, and kick roothub timer.
> Root hub timer requests for port status, finds the port in resume state,
> checks if resume_done[port] timestamp passed, and set port to U0 state.

ehci-hcd does the same thing, except that it also uses this resume_done 
timestamp with host-initiated resumes.

> There are a few issues with this approach,
> 1. A host initated resume will also generate a resume event, the event
>    handler will find the port in resume state, believe it's a device
>    initated and act accordingly.
> 
> 2. A port status request might cut the 20ms resume signalling short if a
>    get_port_status request is handled during the 20ms host resume.
>    The port will be found in resume state. The timestamp is not set leading
>    to time_after_eq(jiffoes, timestamp) returning true, as timestamp = 0.
>    get_port_status will proceed with moving the port to U0.
> 
> 3. If an error, or anything else happends to the port during device
>    initated 20ms resume signalling it will leave all device resume
>    parameters hanging uncleared preventing further resume.
> 
> Fix this by using the existing resuming_ports bitfield to indicate if
> resume signalling timing is taken care of.
> Also check if the resume_done[port] is set  before using it in time
> comparison. Also clear out any resume signalling related variables if port
> is not in U0 or Resume state.

Wouldn't it be better to change the host-initiated resume mechanism to
be consisten with device-initiated resumes?  Or would that be too big a 
change for the time being?

Alan Stern

Re: [TESTPATCH] xhci: fix usb2 resume timing and races.

[Mathias Nyman]

On 01.12.2015 17:47, Alan Stern wrote:
> On Mon, 30 Nov 2015, Mathias Nyman wrote:
>
>> usb2 ports need to signal resume for 20ms before moving to U0 state.
>> Both device and host can initiate resume.
>>
>> On host initated resume port is set to resume state, sleep 20ms,
>> and finally set port to U0 state.
>
> That's an odd approach.  The assumption in usbcore is that the HCD will
> not sleep here.
>
>> On device initated resume a port status interrupt with a port in resume
>> state in issued. The interrupt handler tags a resume_done[port]
>> timestamp with current time + 20ms, and kick roothub timer.
>> Root hub timer requests for port status, finds the port in resume state,
>> checks if resume_done[port] timestamp passed, and set port to U0 state.
>
> ehci-hcd does the same thing, except that it also uses this resume_done
> timestamp with host-initiated resumes.
>
>> There are a few issues with this approach,
>> 1. A host initated resume will also generate a resume event, the event
>>     handler will find the port in resume state, believe it's a device
>>     initated and act accordingly.
>>
>> 2. A port status request might cut the 20ms resume signalling short if a
>>     get_port_status request is handled during the 20ms host resume.
>>     The port will be found in resume state. The timestamp is not set leading
>>     to time_after_eq(jiffoes, timestamp) returning true, as timestamp = 0.
>>     get_port_status will proceed with moving the port to U0.
>>
>> 3. If an error, or anything else happends to the port during device
>>     initated 20ms resume signalling it will leave all device resume
>>     parameters hanging uncleared preventing further resume.
>>
>> Fix this by using the existing resuming_ports bitfield to indicate if
>> resume signalling timing is taken care of.
>> Also check if the resume_done[port] is set  before using it in time
>> comparison. Also clear out any resume signalling related variables if port
>> is not in U0 or Resume state.
>
> Wouldn't it be better to change the host-initiated resume mechanism to
> be consisten with device-initiated resumes?  Or would that be too big a
> change for the time being?
>
> Alan Stern
>

Yes, changing host initiated resume code would make sense.

Hence the comment in the testpatch:

/* Host initated resume doesn't time the resume
  * signalling using resume_done[].
  * It manually sets RESUME state, sleeps 20ms
  * and sets U0 state. This should probably be
  * changed, but not right now, do nothing
  */

I was focusing more on clearing the stale resume related variables and
didn't want to dig into the history of host initiated resume code at that moment.

If ehci-hcd is using the timestamp + kick roothub approach for host resume,
then I don't see why xhci can't do the same.

-Mathias

[TESTPATCH v2] xhci: fix usb2 resume timing and races.

[Mathias Nyman]

usb2 ports need to signal resume for 20ms before moving to U0 state.
Both device and host can initiate resume.

On host initated resume port is set to resume state, sleep 20ms,
and finally set port to U0 state.

On device initated resume a port status interrupt with a port in resume
state in issued. The interrupt handler tags a resume_done[port]
timestamp with current time + 20ms, and kick roothub timer.
Root hub timer requests for port status, finds the port in resume state,
checks if resume_done[port] timestamp passed, and set port to U0 state.

There are a few issues with this approach,
1. A host initated resume will also generate a resume event, the event
   handler will find the port in resume state, believe it's a device
   initated and act accordingly.

2. A port status request might cut the 20ms resume signalling short if a
   get_port_status request is handled during the 20ms host resume.
   The port will be found in resume state. The timestamp is not set leading
   to time_after_eq(jiffoes, timestamp) returning true, as timestamp = 0.
   get_port_status will proceed with moving the port to U0.

3. If an error, or anything else happends to the port during device
   initated 20ms resume signalling it will leave all device resume
   parameters hanging uncleared preventing further resume.

Fix this by using the existing resuming_ports bitfield to indicate if
resume signalling timing is taken care of.
Also check if the resume_done[port] is set  before using it in time
comparison. Also clear out any resume signalling related variables if port
is not in U0 or Resume state.

v2. fix parentheses when checking for uncleared resume variables.
we want: if ((unclear1 OR unclear2 ) AND !in_resume AND !in_U3) { .. }

Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
---
 drivers/usb/host/xhci-hub.c  | 38 ++++++++++++++++++++++++++++++++++++--
 drivers/usb/host/xhci-ring.c |  3 ++-
 2 files changed, 38 insertions(+), 3 deletions(-)

diff --git a/drivers/usb/host/xhci-hub.c b/drivers/usb/host/xhci-hub.c
index 78241b5..a750298 100644
--- a/drivers/usb/host/xhci-hub.c
+++ b/drivers/usb/host/xhci-hub.c
@@ -616,8 +616,30 @@ static u32 xhci_get_port_status(struct usb_hcd *hcd,
 		if ((raw_port_status & PORT_RESET) ||
 				!(raw_port_status & PORT_PE))
 			return 0xffffffff;
-		if (time_after_eq(jiffies,
-					bus_state->resume_done[wIndex])) {
+		/* did port event handler already start 20ms resume timing? */
+		if (!bus_state->resume_done[wIndex]) {
+			/* If not, maybe we are in a host initated resume? */
+			if (test_bit(wIndex, &bus_state->resuming_ports)) {
+				/* Host initated resume doesn't time the resume
+				 * signalling using resume_done[].
+				 * It manually sets RESUME state, sleeps 20ms
+				 * and sets U0 state. This should probably be
+				 * changed, but not right now, do nothing
+				 */
+			} else {
+				/* port resume was discovered now and here,
+				 * start resume timing
+				 */
+				unsigned long timeout = jiffies +
+					msecs_to_jiffies(USB_RESUME_TIMEOUT);
+
+				set_bit(wIndex, &bus_state->resuming_ports);
+				bus_state->resume_done[wIndex] = timeout;
+				mod_timer(&hcd->rh_timer, timeout);
+			}
+		/* Has resume been signalled for 20ms? yet? */
+		} else if (time_after_eq(jiffies,
+					 bus_state->resume_done[wIndex])) {
 			int time_left;
 
 			xhci_dbg(xhci, "Resume USB2 port %d\n",
@@ -665,6 +687,16 @@ static u32 xhci_get_port_status(struct usb_hcd *hcd,
 			status |= USB_PORT_STAT_SUSPEND;
 		}
 	}
+	/* Clear stale usb2 resume signalling variables in case port changed
+	 * state during 20ms resume signalling. For example on error
+	 */
+	if ((bus_state->resume_done[wIndex] ||
+	     test_bit(wIndex, &bus_state->resuming_ports)) &&
+	     (raw_port_status & PORT_PLS_MASK) != XDEV_U3 &&
+	     (raw_port_status & PORT_PLS_MASK) != XDEV_RESUME) {
+		bus_state->resume_done[wIndex] = 0;
+		clear_bit(wIndex, &bus_state->resuming_ports);
+	}
 	if ((raw_port_status & PORT_PLS_MASK) == XDEV_U0
 			&& (raw_port_status & PORT_POWER)
 			&& (bus_state->suspended_ports & (1 << wIndex))) {
@@ -995,6 +1027,7 @@ int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
 				if ((temp & PORT_PE) == 0)
 					goto error;
 
+				set_bit(wIndex, &bus_state->resuming_ports);
 				xhci_set_link_state(xhci, port_array, wIndex,
 							XDEV_RESUME);
 				spin_unlock_irqrestore(&xhci->lock, flags);
@@ -1002,6 +1035,7 @@ int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
 				spin_lock_irqsave(&xhci->lock, flags);
 				xhci_set_link_state(xhci, port_array, wIndex,
 							XDEV_U0);
+				clear_bit(wIndex, &bus_state->resuming_ports);
 			}
 			bus_state->port_c_suspend |= 1 << wIndex;
 
diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c
index 97ffe39..3743bb2 100644
--- a/drivers/usb/host/xhci-ring.c
+++ b/drivers/usb/host/xhci-ring.c
@@ -1583,7 +1583,8 @@ static void handle_port_status(struct xhci_hcd *xhci,
 			 */
 			bogus_port_status = true;
 			goto cleanup;
-		} else {
+		} else if (!test_bit(faked_port_index,
+				     &bus_state->resuming_ports)) {
 			xhci_dbg(xhci, "resume HS port %d\n", port_id);
 			bus_state->resume_done[faked_port_index] = jiffies +
 				msecs_to_jiffies(USB_RESUME_TIMEOUT);
-- 
1.9.1

Re: [TESTPATCH v2] xhci: fix usb2 resume timing and races.

[Felipe Balbi]

[-- Attachment #1: Type: text/plain, Size: 6403 bytes --]


Hi,

Mathias Nyman <mathias.nyman@linux.intel.com> writes:
> usb2 ports need to signal resume for 20ms before moving to U0 state.

at least 20ms ;-) Recently, we decided to drive resume for 40ms to
support devices with broken FW.

> Both device and host can initiate resume.
>
> On host initated resume port is set to resume state, sleep 20ms,

sleep 40ms:

include/linux/usb.h:232:#define USB_RESUME_TIMEOUT      40 /* ms */

> and finally set port to U0 state.
>
> On device initated resume a port status interrupt with a port in resume
> state in issued. The interrupt handler tags a resume_done[port]
> timestamp with current time + 20ms, and kick roothub timer.

+ 40ms ?

> Root hub timer requests for port status, finds the port in resume state,
> checks if resume_done[port] timestamp passed, and set port to U0 state.
>
> There are a few issues with this approach,
> 1. A host initated resume will also generate a resume event, the event
>    handler will find the port in resume state, believe it's a device
>    initated and act accordingly.
>
> 2. A port status request might cut the 20ms resume signalling short if a
>    get_port_status request is handled during the 20ms host resume.
>    The port will be found in resume state. The timestamp is not set leading
>    to time_after_eq(jiffoes, timestamp) returning true, as timestamp = 0.
>    get_port_status will proceed with moving the port to U0.
>
> 3. If an error, or anything else happends to the port during device
>    initated 20ms resume signalling it will leave all device resume
>    parameters hanging uncleared preventing further resume.
>
> Fix this by using the existing resuming_ports bitfield to indicate if
> resume signalling timing is taken care of.
> Also check if the resume_done[port] is set  before using it in time
> comparison. Also clear out any resume signalling related variables if port
> is not in U0 or Resume state.
>
> v2. fix parentheses when checking for uncleared resume variables.
> we want: if ((unclear1 OR unclear2 ) AND !in_resume AND !in_U3) { .. }

this 'v2' note doesn't have to go into commit log, IMO.

> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
> ---
>  drivers/usb/host/xhci-hub.c  | 38 ++++++++++++++++++++++++++++++++++++--
>  drivers/usb/host/xhci-ring.c |  3 ++-
>  2 files changed, 38 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/usb/host/xhci-hub.c b/drivers/usb/host/xhci-hub.c
> index 78241b5..a750298 100644
> --- a/drivers/usb/host/xhci-hub.c
> +++ b/drivers/usb/host/xhci-hub.c
> @@ -616,8 +616,30 @@ static u32 xhci_get_port_status(struct usb_hcd *hcd,
>  		if ((raw_port_status & PORT_RESET) ||
>  				!(raw_port_status & PORT_PE))
>  			return 0xffffffff;
> -		if (time_after_eq(jiffies,
> -					bus_state->resume_done[wIndex])) {
> +		/* did port event handler already start 20ms resume timing? */
> +		if (!bus_state->resume_done[wIndex]) {
> +			/* If not, maybe we are in a host initated resume? */
> +			if (test_bit(wIndex, &bus_state->resuming_ports)) {
> +				/* Host initated resume doesn't time the resume
> +				 * signalling using resume_done[].
> +				 * It manually sets RESUME state, sleeps 20ms
> +				 * and sets U0 state. This should probably be
> +				 * changed, but not right now, do nothing
> +				 */
> +			} else {
> +				/* port resume was discovered now and here,
> +				 * start resume timing
> +				 */
> +				unsigned long timeout = jiffies +
> +					msecs_to_jiffies(USB_RESUME_TIMEOUT);
> +
> +				set_bit(wIndex, &bus_state->resuming_ports);
> +				bus_state->resume_done[wIndex] = timeout;
> +				mod_timer(&hcd->rh_timer, timeout);
> +			}
> +		/* Has resume been signalled for 20ms? yet? */

How about: "Has resume been signalled for at least 20ms?"

Or even better:

Has resume been signalled for at least USB_RESUME_TIMEOUT ms yet ?

> +		} else if (time_after_eq(jiffies,
> +					 bus_state->resume_done[wIndex])) {
>  			int time_left;
>  
>  			xhci_dbg(xhci, "Resume USB2 port %d\n",
> @@ -665,6 +687,16 @@ static u32 xhci_get_port_status(struct usb_hcd *hcd,
>  			status |= USB_PORT_STAT_SUSPEND;
>  		}
>  	}
> +	/* Clear stale usb2 resume signalling variables in case port changed
> +	 * state during 20ms resume signalling. For example on error
> +	 */
> +	if ((bus_state->resume_done[wIndex] ||
> +	     test_bit(wIndex, &bus_state->resuming_ports)) &&
> +	     (raw_port_status & PORT_PLS_MASK) != XDEV_U3 &&
> +	     (raw_port_status & PORT_PLS_MASK) != XDEV_RESUME) {
> +		bus_state->resume_done[wIndex] = 0;
> +		clear_bit(wIndex, &bus_state->resuming_ports);
> +	}
>  	if ((raw_port_status & PORT_PLS_MASK) == XDEV_U0
>  			&& (raw_port_status & PORT_POWER)
>  			&& (bus_state->suspended_ports & (1 << wIndex))) {
> @@ -995,6 +1027,7 @@ int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
>  				if ((temp & PORT_PE) == 0)
>  					goto error;
>  
> +				set_bit(wIndex, &bus_state->resuming_ports);
>  				xhci_set_link_state(xhci, port_array, wIndex,
>  							XDEV_RESUME);
>  				spin_unlock_irqrestore(&xhci->lock, flags);
> @@ -1002,6 +1035,7 @@ int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
>  				spin_lock_irqsave(&xhci->lock, flags);
>  				xhci_set_link_state(xhci, port_array, wIndex,
>  							XDEV_U0);
> +				clear_bit(wIndex, &bus_state->resuming_ports);
>  			}
>  			bus_state->port_c_suspend |= 1 << wIndex;
>  
> diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c
> index 97ffe39..3743bb2 100644
> --- a/drivers/usb/host/xhci-ring.c
> +++ b/drivers/usb/host/xhci-ring.c
> @@ -1583,7 +1583,8 @@ static void handle_port_status(struct xhci_hcd *xhci,
>  			 */
>  			bogus_port_status = true;
>  			goto cleanup;
> -		} else {
> +		} else if (!test_bit(faked_port_index,
> +				     &bus_state->resuming_ports)) {
>  			xhci_dbg(xhci, "resume HS port %d\n", port_id);
>  			bus_state->resume_done[faked_port_index] = jiffies +
>  				msecs_to_jiffies(USB_RESUME_TIMEOUT);
> -- 
> 1.9.1
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at  http://www.tux.org/lkml/

-- 
balbi

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 818 bytes --]

Re: [TESTPATCH v2] xhci: fix usb2 resume timing and races.

[Mathias Nyman]

On 01.12.2015 16:32, Felipe Balbi wrote:
>
> Hi,
>
> Mathias Nyman <mathias.nyman@linux.intel.com> writes:
>> usb2 ports need to signal resume for 20ms before moving to U0 state.
>
> at least 20ms ;-) Recently, we decided to drive resume for 40ms to
> support devices with broken FW.
>

True, but specs talk about 20ms, and I'm just trying to give some context for what's
going on. This testpatch doesn't touch the timings.

Daniel is able to trigger a USB2 xhci resume issue which I hope is fixed with this patch.
This is especially made for his setup running a 4.3 kernel

If this works I'll clean up all the "20ms" in the commit message and comments.

Just noticed that xhci USB2 host initiated resume uses a hardcoded msleep(20).
That needs to be changed to USB_RESUME_TIMEOUT at some point.
For now I'm just interested in knowing if this patch works.

>
> this 'v2' note doesn't have to go into commit log, IMO.
>

It's going to be cleaned out as well, just there to explain to Daniel, and the world why
a second version of the testpatch was created.

-Mathias

Re: [TESTPATCH v2] xhci: fix usb2 resume timing and races.

[Felipe Balbi]

[-- Attachment #1: Type: text/plain, Size: 1228 bytes --]


Hi,

Mathias Nyman <mathias.nyman@linux.intel.com> writes:
> On 01.12.2015 16:32, Felipe Balbi wrote:
>>
>> Hi,
>>
>> Mathias Nyman <mathias.nyman@linux.intel.com> writes:
>>> usb2 ports need to signal resume for 20ms before moving to U0 state.
>>
>> at least 20ms ;-) Recently, we decided to drive resume for 40ms to
>> support devices with broken FW.
>>
>
> True, but specs talk about 20ms, and I'm just trying to give some context for what's
> going on. This testpatch doesn't touch the timings.
>
> Daniel is able to trigger a USB2 xhci resume issue which I hope is fixed with this patch.
> This is especially made for his setup running a 4.3 kernel
>
> If this works I'll clean up all the "20ms" in the commit message and comments.
>
> Just noticed that xhci USB2 host initiated resume uses a hardcoded msleep(20).
> That needs to be changed to USB_RESUME_TIMEOUT at some point.
> For now I'm just interested in knowing if this patch works.
>
>>
>> this 'v2' note doesn't have to go into commit log, IMO.
>>
>
> It's going to be cleaned out as well, just there to explain to Daniel, and the world why
> a second version of the testpatch was created.

all right, thanks ;-)

-- 
balbi

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 818 bytes --]

Re: [TESTPATCH v2] xhci: fix usb2 resume timing and races.

[Daniel J Blueman]

On 1 December 2015 at 16:26, Mathias Nyman
<mathias.nyman@linux.intel.com> wrote:
> usb2 ports need to signal resume for 20ms before moving to U0 state.
> Both device and host can initiate resume.
>
> On host initated resume port is set to resume state, sleep 20ms,
> and finally set port to U0 state.
>
> On device initated resume a port status interrupt with a port in resume
> state in issued. The interrupt handler tags a resume_done[port]
> timestamp with current time + 20ms, and kick roothub timer.
> Root hub timer requests for port status, finds the port in resume state,
> checks if resume_done[port] timestamp passed, and set port to U0 state.
>
> There are a few issues with this approach,
> 1. A host initated resume will also generate a resume event, the event
>    handler will find the port in resume state, believe it's a device
>    initated and act accordingly.
>
> 2. A port status request might cut the 20ms resume signalling short if a
>    get_port_status request is handled during the 20ms host resume.
>    The port will be found in resume state. The timestamp is not set leading
>    to time_after_eq(jiffoes, timestamp) returning true, as timestamp = 0.
>    get_port_status will proceed with moving the port to U0.
>
> 3. If an error, or anything else happends to the port during device
>    initated 20ms resume signalling it will leave all device resume
>    parameters hanging uncleared preventing further resume.
>
> Fix this by using the existing resuming_ports bitfield to indicate if
> resume signalling timing is taken care of.
> Also check if the resume_done[port] is set  before using it in time
> comparison. Also clear out any resume signalling related variables if port
> is not in U0 or Resume state.
>
> v2. fix parentheses when checking for uncleared resume variables.
> we want: if ((unclear1 OR unclear2 ) AND !in_resume AND !in_U3) { .. }
>
> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>

Excellent; this correctly prevents the cyclic chain of suspend
attempts, resolving the issue.

Tested-by: Daniel J Blueman <daniel@quora.org>

Thanks Mathias!
  Daniel

Re: [TESTPATCH v2] xhci: fix usb2 resume timing and races.

[Mathias Nyman]

On 05.12.2015 06:02, Daniel J Blueman wrote:
> On 1 December 2015 at 16:26, Mathias Nyman
> <mathias.nyman@linux.intel.com> wrote:
>> usb2 ports need to signal resume for 20ms before moving to U0 state.
>> Both device and host can initiate resume.
>>
>> On host initated resume port is set to resume state, sleep 20ms,
>> and finally set port to U0 state.
>>
>> On device initated resume a port status interrupt with a port in resume
>> state in issued. The interrupt handler tags a resume_done[port]
>> timestamp with current time + 20ms, and kick roothub timer.
>> Root hub timer requests for port status, finds the port in resume state,
>> checks if resume_done[port] timestamp passed, and set port to U0 state.
>>
>> There are a few issues with this approach,
>> 1. A host initated resume will also generate a resume event, the event
>>     handler will find the port in resume state, believe it's a device
>>     initated and act accordingly.
>>
>> 2. A port status request might cut the 20ms resume signalling short if a
>>     get_port_status request is handled during the 20ms host resume.
>>     The port will be found in resume state. The timestamp is not set leading
>>     to time_after_eq(jiffoes, timestamp) returning true, as timestamp = 0.
>>     get_port_status will proceed with moving the port to U0.
>>
>> 3. If an error, or anything else happends to the port during device
>>     initated 20ms resume signalling it will leave all device resume
>>     parameters hanging uncleared preventing further resume.
>>
>> Fix this by using the existing resuming_ports bitfield to indicate if
>> resume signalling timing is taken care of.
>> Also check if the resume_done[port] is set  before using it in time
>> comparison. Also clear out any resume signalling related variables if port
>> is not in U0 or Resume state.
>>
>> v2. fix parentheses when checking for uncleared resume variables.
>> we want: if ((unclear1 OR unclear2 ) AND !in_resume AND !in_U3) { .. }
>>
>> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
>
> Excellent; this correctly prevents the cyclic chain of suspend
> attempts, resolving the issue.
>
> Tested-by: Daniel J Blueman <daniel@quora.org>
>
> Thanks Mathias!
>    Daniel
>

Thanks for testing it
I'll do some minor cleanups and add it to the queue

-Mathias