* [PATCH] iommu: silence iommu group prints
@ 2020-02-27 11:57 Russell King
2020-02-27 13:44 ` Robin Murphy
` (2 more replies)
0 siblings, 3 replies; 24+ messages in thread
From: Russell King @ 2020-02-27 11:57 UTC (permalink / raw)
To: Joerg Roedel; +Cc: iommu
On the LX2160A, there are lots (about 160) of IOMMU messages produced
during boot; this is excessive. Reduce the severity of these messages
to debug level.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
---
drivers/iommu/iommu.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/iommu/iommu.c b/drivers/iommu/iommu.c
index 3ead597e1c57..304281ec623b 100644
--- a/drivers/iommu/iommu.c
+++ b/drivers/iommu/iommu.c
@@ -741,7 +741,7 @@ int iommu_group_add_device(struct iommu_group *group, struct device *dev)
trace_add_device_to_group(group->id, dev);
- dev_info(dev, "Adding to iommu group %d\n", group->id);
+ dev_dbg(dev, "Adding to iommu group %d\n", group->id);
return 0;
@@ -775,7 +775,7 @@ void iommu_group_remove_device(struct device *dev)
struct iommu_group *group = dev->iommu_group;
struct group_device *tmp_device, *device = NULL;
- dev_info(dev, "Removing from iommu group %d\n", group->id);
+ dev_dbg(dev, "Removing from iommu group %d\n", group->id);
/* Pre-notify listeners that a device is being removed. */
blocking_notifier_call_chain(&group->notifier,
--
2.20.1
_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu
^ permalink raw reply related [flat|nested] 24+ messages in thread
* Re: [PATCH] iommu: silence iommu group prints
2020-02-27 11:57 [PATCH] iommu: silence iommu group prints Russell King
@ 2020-02-27 13:44 ` Robin Murphy
2020-02-27 13:48 ` Russell King - ARM Linux admin
2020-02-28 2:16 ` Lu Baolu
2020-03-02 15:44 ` Joerg Roedel
2 siblings, 1 reply; 24+ messages in thread
From: Robin Murphy @ 2020-02-27 13:44 UTC (permalink / raw)
To: Russell King, Joerg Roedel; +Cc: iommu
On 27/02/2020 11:57 am, Russell King wrote:
> On the LX2160A, there are lots (about 160) of IOMMU messages produced
> during boot; this is excessive. Reduce the severity of these messages
> to debug level.
That's... a lot. Does the system really have that many devices, or is
some driver being stupid and repeatedly populating and destroying an
entire bus in a probe-deferral dance?
I have no real objection to the change itself - it can be handy to see
these when diagnosing dmesg dumps over email, but it's nothing that
can't be gleaned from sysfs later even without dynamic debug - I'm just
curious as to what leads to such an unusually obnoxious spamming.
Robin.
> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
> ---
> drivers/iommu/iommu.c | 4 ++--
> 1 file changed, 2 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/iommu/iommu.c b/drivers/iommu/iommu.c
> index 3ead597e1c57..304281ec623b 100644
> --- a/drivers/iommu/iommu.c
> +++ b/drivers/iommu/iommu.c
> @@ -741,7 +741,7 @@ int iommu_group_add_device(struct iommu_group *group, struct device *dev)
>
> trace_add_device_to_group(group->id, dev);
>
> - dev_info(dev, "Adding to iommu group %d\n", group->id);
> + dev_dbg(dev, "Adding to iommu group %d\n", group->id);
>
> return 0;
>
> @@ -775,7 +775,7 @@ void iommu_group_remove_device(struct device *dev)
> struct iommu_group *group = dev->iommu_group;
> struct group_device *tmp_device, *device = NULL;
>
> - dev_info(dev, "Removing from iommu group %d\n", group->id);
> + dev_dbg(dev, "Removing from iommu group %d\n", group->id);
>
> /* Pre-notify listeners that a device is being removed. */
> blocking_notifier_call_chain(&group->notifier,
>
_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH] iommu: silence iommu group prints
2020-02-27 13:44 ` Robin Murphy
@ 2020-02-27 13:48 ` Russell King - ARM Linux admin
2020-02-27 18:19 ` Robin Murphy
0 siblings, 1 reply; 24+ messages in thread
From: Russell King - ARM Linux admin @ 2020-02-27 13:48 UTC (permalink / raw)
To: Robin Murphy; +Cc: iommu
On Thu, Feb 27, 2020 at 01:44:56PM +0000, Robin Murphy wrote:
> On 27/02/2020 11:57 am, Russell King wrote:
> > On the LX2160A, there are lots (about 160) of IOMMU messages produced
> > during boot; this is excessive. Reduce the severity of these messages
> > to debug level.
>
> That's... a lot. Does the system really have that many devices, or is some
> driver being stupid and repeatedly populating and destroying an entire bus
> in a probe-deferral dance?
It's all the devices created by for the mc-bus for the DPAA2
networking support. I don't know the technicalities, just that
the boot is spammed with these messages.
--
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up
According to speedtest.net: 11.9Mbps down 500kbps up
_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH] iommu: silence iommu group prints
2020-02-27 13:48 ` Russell King - ARM Linux admin
@ 2020-02-27 18:19 ` Robin Murphy
2020-02-27 19:00 ` Russell King - ARM Linux admin
0 siblings, 1 reply; 24+ messages in thread
From: Robin Murphy @ 2020-02-27 18:19 UTC (permalink / raw)
To: Russell King - ARM Linux admin; +Cc: iommu
On 27/02/2020 1:48 pm, Russell King - ARM Linux admin wrote:
> On Thu, Feb 27, 2020 at 01:44:56PM +0000, Robin Murphy wrote:
>> On 27/02/2020 11:57 am, Russell King wrote:
>>> On the LX2160A, there are lots (about 160) of IOMMU messages produced
>>> during boot; this is excessive. Reduce the severity of these messages
>>> to debug level.
>>
>> That's... a lot. Does the system really have that many devices, or is some
>> driver being stupid and repeatedly populating and destroying an entire bus
>> in a probe-deferral dance?
>
> It's all the devices created by for the mc-bus for the DPAA2
> networking support. I don't know the technicalities, just that
> the boot is spammed with these messages.
Well, the "technicalities" are really just whether the thing before the
colon on each message is unique or not. If you're seeing multiple add
and remove calls pertaining to the same device (or frankly any remove
calls at all during boot) then it smacks of something somewhere wasting
time and resources with unnecessary busywork, which is indicative of
either poor design or an actual bug, either of which would deserve fixing.
Robin.
_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH] iommu: silence iommu group prints
2020-02-27 18:19 ` Robin Murphy
@ 2020-02-27 19:00 ` Russell King - ARM Linux admin
0 siblings, 0 replies; 24+ messages in thread
From: Russell King - ARM Linux admin @ 2020-02-27 19:00 UTC (permalink / raw)
To: Robin Murphy; +Cc: iommu
On Thu, Feb 27, 2020 at 06:19:10PM +0000, Robin Murphy wrote:
> On 27/02/2020 1:48 pm, Russell King - ARM Linux admin wrote:
> > On Thu, Feb 27, 2020 at 01:44:56PM +0000, Robin Murphy wrote:
> > > On 27/02/2020 11:57 am, Russell King wrote:
> > > > On the LX2160A, there are lots (about 160) of IOMMU messages produced
> > > > during boot; this is excessive. Reduce the severity of these messages
> > > > to debug level.
> > >
> > > That's... a lot. Does the system really have that many devices, or is some
> > > driver being stupid and repeatedly populating and destroying an entire bus
> > > in a probe-deferral dance?
> >
> > It's all the devices created by for the mc-bus for the DPAA2
> > networking support. I don't know the technicalities, just that
> > the boot is spammed with these messages.
>
> Well, the "technicalities" are really just whether the thing before the
> colon on each message is unique or not. If you're seeing multiple add and
> remove calls pertaining to the same device (or frankly any remove calls at
> all during boot) then it smacks of something somewhere wasting time and
> resources with unnecessary busywork, which is indicative of either poor
> design or an actual bug, either of which would deserve fixing.
It's not the same device.
--
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up
According to speedtest.net: 11.9Mbps down 500kbps up
_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH] iommu: silence iommu group prints
2020-02-27 11:57 [PATCH] iommu: silence iommu group prints Russell King
2020-02-27 13:44 ` Robin Murphy
@ 2020-02-28 2:16 ` Lu Baolu
2020-02-28 9:33 ` John Garry
2020-03-02 15:44 ` Joerg Roedel
2 siblings, 1 reply; 24+ messages in thread
From: Lu Baolu @ 2020-02-28 2:16 UTC (permalink / raw)
To: Russell King, Joerg Roedel; +Cc: iommu
Hi,
On 2020/2/27 19:57, Russell King wrote:
> On the LX2160A, there are lots (about 160) of IOMMU messages produced
> during boot; this is excessive. Reduce the severity of these messages
> to debug level.
>
> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
> ---
> drivers/iommu/iommu.c | 4 ++--
> 1 file changed, 2 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/iommu/iommu.c b/drivers/iommu/iommu.c
> index 3ead597e1c57..304281ec623b 100644
> --- a/drivers/iommu/iommu.c
> +++ b/drivers/iommu/iommu.c
> @@ -741,7 +741,7 @@ int iommu_group_add_device(struct iommu_group *group, struct device *dev)
>
> trace_add_device_to_group(group->id, dev);
>
> - dev_info(dev, "Adding to iommu group %d\n", group->id);
> + dev_dbg(dev, "Adding to iommu group %d\n", group->id);
I'm not strongly against this. But to me this message seems to be a good
indicator that a device was probed successfully by the iommu subsystem.
Keeping it in the default kernel message always helps to the kernel
debugging.
Best regards,
baolu
_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH] iommu: silence iommu group prints
2020-02-28 2:16 ` Lu Baolu
@ 2020-02-28 9:33 ` John Garry
2020-02-28 10:06 ` Russell King - ARM Linux admin
0 siblings, 1 reply; 24+ messages in thread
From: John Garry @ 2020-02-28 9:33 UTC (permalink / raw)
To: Lu Baolu, Russell King, Joerg Roedel; +Cc: iommu
On 28/02/2020 02:16, Lu Baolu wrote:
> Hi,
>
> On 2020/2/27 19:57, Russell King wrote:
>> On the LX2160A, there are lots (about 160) of IOMMU messages produced
>> during boot; this is excessive. Reduce the severity of these messages
>> to debug level.
>>
>> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
>> ---
>> drivers/iommu/iommu.c | 4 ++--
>> 1 file changed, 2 insertions(+), 2 deletions(-)
>>
>> diff --git a/drivers/iommu/iommu.c b/drivers/iommu/iommu.c
>> index 3ead597e1c57..304281ec623b 100644
>> --- a/drivers/iommu/iommu.c
>> +++ b/drivers/iommu/iommu.c
>> @@ -741,7 +741,7 @@ int iommu_group_add_device(struct iommu_group
>> *group, struct device *dev)
>> trace_add_device_to_group(group->id, dev);
>> - dev_info(dev, "Adding to iommu group %d\n", group->id);
>> + dev_dbg(dev, "Adding to iommu group %d\n", group->id);
>
> I'm not strongly against this. But to me this message seems to be a good
> indicator that a device was probed successfully by the iommu subsystem.
> Keeping it in the default kernel message always helps to the kernel
> debugging.
>
I would tend to agree.
> Best regards,
> baolu
> _______________________________________________
> iommu mailing list
> iommu@lists.linux-foundation.org
> https://lists.linuxfoundation.org/mailman/listinfo/iommu
> .
_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH] iommu: silence iommu group prints
2020-02-28 9:33 ` John Garry
@ 2020-02-28 10:06 ` Russell King - ARM Linux admin
2020-02-28 18:32 ` Robin Murphy
0 siblings, 1 reply; 24+ messages in thread
From: Russell King - ARM Linux admin @ 2020-02-28 10:06 UTC (permalink / raw)
To: John Garry; +Cc: iommu
On Fri, Feb 28, 2020 at 09:33:40AM +0000, John Garry wrote:
> On 28/02/2020 02:16, Lu Baolu wrote:
> > Hi,
> >
> > On 2020/2/27 19:57, Russell King wrote:
> > > On the LX2160A, there are lots (about 160) of IOMMU messages produced
> > > during boot; this is excessive. Reduce the severity of these messages
> > > to debug level.
> > >
> > > Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
> > > ---
> > > drivers/iommu/iommu.c | 4 ++--
> > > 1 file changed, 2 insertions(+), 2 deletions(-)
> > >
> > > diff --git a/drivers/iommu/iommu.c b/drivers/iommu/iommu.c
> > > index 3ead597e1c57..304281ec623b 100644
> > > --- a/drivers/iommu/iommu.c
> > > +++ b/drivers/iommu/iommu.c
> > > @@ -741,7 +741,7 @@ int iommu_group_add_device(struct iommu_group
> > > *group, struct device *dev)
> > > trace_add_device_to_group(group->id, dev);
> > > - dev_info(dev, "Adding to iommu group %d\n", group->id);
> > > + dev_dbg(dev, "Adding to iommu group %d\n", group->id);
> >
> > I'm not strongly against this. But to me this message seems to be a good
> > indicator that a device was probed successfully by the iommu subsystem.
> > Keeping it in the default kernel message always helps to the kernel
> > debugging.
> >
>
> I would tend to agree.
Here's the boot messages. Notice how many of these "Adding to iommu
group" messages there are:
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083]
[ 0.000000] Linux version 5.5.0+ (rmk@rmk-PC) (gcc version 4.9.2 (GCC)) #655 SMP PREEMPT Fri Feb 28 09:54:47 GMT 2020
[ 0.000000] Machine model: SolidRun LX2160A Clearfog CX
[ 0.000000] earlycon: pl11 at MMIO32 0x00000000021c0000 (options '')
[ 0.000000] printk: bootconsole [pl11] enabled
[ 0.000000] efi: Getting EFI parameters from FDT:
[ 0.000000] efi: UEFI not found.
[ 0.000000] cma: Reserved 32 MiB at 0x00000000f9c00000
[ 0.000000] On node 0 totalpages: 1555968
[ 0.000000] DMA zone: 4096 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 262144 pages, LIFO batch:63
[ 0.000000] DMA32 zone: 3832 pages used for memmap
[ 0.000000] DMA32 zone: 245248 pages, LIFO batch:63
[ 0.000000] Normal zone: 16384 pages used for memmap
[ 0.000000] Normal zone: 1048576 pages, LIFO batch:63
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.1
[ 0.000000] percpu: Embedded 31 pages/cpu s88968 r8192 d29816 u126976
[ 0.000000] pcpu-alloc: s88968 r8192 d29816 u126976 alloc=31*4096
[ 0.000000] pcpu-alloc: [0] 00 [0] 01 [0] 02 [0] 03 [0] 04 [0] 05 [0] 06 [0] 07
[ 0.000000] pcpu-alloc: [0] 08 [0] 09 [0] 10 [0] 11 [0] 12 [0] 13 [0] 14 [0] 15
[ 0.000000] Detected PIPT I-cache on CPU0
[ 0.000000] CPU features: detected: GIC system register CPU interface
[ 0.000000] CPU features: detected: EL2 vector hardening
[ 0.000000] Speculative Store Bypass Disable mitigation not required
[ 0.000000] CPU features: detected: ARM erratum 1319367
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1531656
[ 0.000000] Kernel command line: console=ttyAMA0,115200 root=PARTUUID=c7837e2f-02 rootwait earlycon=pl011,mmio32,0x21c0000 ramdisk_size=0 pci=pcie_bus_perf arm_smmu.disable_bypass=0 iommu.passthrough=0
[ 0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] software IO TLB: mapped [mem 0xbbfff000-0xbffff000] (64MB)
[ 0.000000] Memory: 5991500K/6223872K available (10172K kernel code, 1376K rwdata, 3888K rodata, 960K init, 4326K bss, 199604K reserved, 32768K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=16, Nodes=1
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=16.
[ 0.000000] Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=16
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[ 0.000000] GICv3: 256 SPIs implemented
[ 0.000000] GICv3: 0 Extended SPIs implemented
[ 0.000000] GICv3: Distributor has no Range Selector support
[ 0.000000] GICv3: 16 PPIs implemented
[ 0.000000] GICv3: no VLPI support, no direct LPI support
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006200000
[ 0.000000] ITS [mem 0x06020000-0x0603ffff]
[ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices @2178d00000 (flat, esz 8, psz 64K, shr 0)
[ 0.000000] ITS: using cache flushing for cmd queue
[ 0.000000] GICv3: using LPI property table @0x0000002178cd0000
[ 0.000000] GIC: using cache flushing for LPI property table
[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000002178ce0000
[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c409fb33, max_idle_ns: 440795203156 ns
[ 0.000002] sched_clock: 56 bits at 25MHz, resolution 39ns, wraps every 4398046511103ns
[ 0.006921] Console: colour dummy device 80x25
[ 0.010093] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[ 0.016605] ... MAX_LOCKDEP_SUBCLASSES: 8
[ 0.019421] ... MAX_LOCK_DEPTH: 48
[ 0.022329] ... MAX_LOCKDEP_KEYS: 8192
[ 0.025408] ... CLASSHASH_SIZE: 4096
[ 0.028491] ... MAX_LOCKDEP_ENTRIES: 32768
[ 0.031659] ... MAX_LOCKDEP_CHAINS: 65536
[ 0.034830] ... CHAINHASH_SIZE: 32768
[ 0.037997] memory used by lock dependency info: 3509 kB
[ 0.042135] per task-struct memory footprint: 1920 bytes
[ 0.046292] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000)
[ 0.055443] pid_max: default: 32768 minimum: 301
[ 0.058844] LSM: Security Framework initializing
[ 0.062241] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.068602] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.099452] ASID allocator initialised with 32768 entries
[ 0.111615] rcu: Hierarchical SRCU implementation.
[ 0.119672] Platform MSI: gic-its@6020000 domain created
[ 0.123765] PCI/MSI: /interrupt-controller@6000000/gic-its@6020000 domain created
[ 0.130045] fsl-mc MSI: /interrupt-controller@6000000/gic-its@6020000 domain created
[ 0.136572] EFI services will not be available.
[ 0.148587] smp: Bringing up secondary CPUs ...
[ 0.180732] Detected PIPT I-cache on CPU1
[ 0.180749] GICv3: CPU1: found redistributor 1 region 0:0x0000000006220000
[ 0.180761] GICv3: CPU1: using allocated LPI pending table @0x0000002178cf0000
[ 0.180781] CPU1: Booted secondary processor 0x0000000001 [0x410fd083]
[ 0.212781] Detected PIPT I-cache on CPU2
[ 0.212797] GICv3: CPU2: found redistributor 100 region 0:0x0000000006240000
[ 0.212810] GICv3: CPU2: using allocated LPI pending table @0x0000002178d80000
[ 0.212830] CPU2: Booted secondary processor 0x0000000100 [0x410fd083]
[ 0.244832] Detected PIPT I-cache on CPU3
[ 0.244844] GICv3: CPU3: found redistributor 101 region 0:0x0000000006260000
[ 0.244855] GICv3: CPU3: using allocated LPI pending table @0x0000002178d90000
[ 0.244871] CPU3: Booted secondary processor 0x0000000101 [0x410fd083]
[ 0.276894] Detected PIPT I-cache on CPU4
[ 0.276910] GICv3: CPU4: found redistributor 200 region 0:0x0000000006280000
[ 0.276922] GICv3: CPU4: using allocated LPI pending table @0x0000002178da0000
[ 0.276941] CPU4: Booted secondary processor 0x0000000200 [0x410fd083]
[ 0.308953] Detected PIPT I-cache on CPU5
[ 0.308966] GICv3: CPU5: found redistributor 201 region 0:0x00000000062a0000
[ 0.308978] GICv3: CPU5: using allocated LPI pending table @0x0000002178db0000
[ 0.308994] CPU5: Booted secondary processor 0x0000000201 [0x410fd083]
[ 0.341009] Detected PIPT I-cache on CPU6
[ 0.341027] GICv3: CPU6: found redistributor 300 region 0:0x00000000062c0000
[ 0.341039] GICv3: CPU6: using allocated LPI pending table @0x0000002178dc0000
[ 0.341058] CPU6: Booted secondary processor 0x0000000300 [0x410fd083]
[ 0.373064] Detected PIPT I-cache on CPU7
[ 0.373079] GICv3: CPU7: found redistributor 301 region 0:0x00000000062e0000
[ 0.373091] GICv3: CPU7: using allocated LPI pending table @0x0000002178dd0000
[ 0.373106] CPU7: Booted secondary processor 0x0000000301 [0x410fd083]
[ 0.405124] Detected PIPT I-cache on CPU8
[ 0.405143] GICv3: CPU8: found redistributor 400 region 0:0x0000000006300000
[ 0.405156] GICv3: CPU8: using allocated LPI pending table @0x0000002178de0000
[ 0.405175] CPU8: Booted secondary processor 0x0000000400 [0x410fd083]
[ 0.437179] Detected PIPT I-cache on CPU9
[ 0.437195] GICv3: CPU9: found redistributor 401 region 0:0x0000000006320000
[ 0.437207] GICv3: CPU9: using allocated LPI pending table @0x0000002178df0000
[ 0.437223] CPU9: Booted secondary processor 0x0000000401 [0x410fd083]
[ 0.469240] Detected PIPT I-cache on CPU10
[ 0.469261] GICv3: CPU10: found redistributor 500 region 0:0x0000000006340000
[ 0.469273] GICv3: CPU10: using allocated LPI pending table @0x0000002178e00000
[ 0.469293] CPU10: Booted secondary processor 0x0000000500 [0x410fd083]
[ 0.501296] Detected PIPT I-cache on CPU11
[ 0.501314] GICv3: CPU11: found redistributor 501 region 0:0x0000000006360000
[ 0.501326] GICv3: CPU11: using allocated LPI pending table @0x0000002178e10000
[ 0.501342] CPU11: Booted secondary processor 0x0000000501 [0x410fd083]
[ 0.533362] Detected PIPT I-cache on CPU12
[ 0.533385] GICv3: CPU12: found redistributor 600 region 0:0x0000000006380000
[ 0.533397] GICv3: CPU12: using allocated LPI pending table @0x0000002178e20000
[ 0.533418] CPU12: Booted secondary processor 0x0000000600 [0x410fd083]
[ 0.565408] Detected PIPT I-cache on CPU13
[ 0.565427] GICv3: CPU13: found redistributor 601 region 0:0x00000000063a0000
[ 0.565440] GICv3: CPU13: using allocated LPI pending table @0x0000002178e30000
[ 0.565455] CPU13: Booted secondary processor 0x0000000601 [0x410fd083]
[ 0.597470] Detected PIPT I-cache on CPU14
[ 0.597494] GICv3: CPU14: found redistributor 700 region 0:0x00000000063c0000
[ 0.597507] GICv3: CPU14: using allocated LPI pending table @0x0000002178e40000
[ 0.597527] CPU14: Booted secondary processor 0x0000000700 [0x410fd083]
[ 0.629523] Detected PIPT I-cache on CPU15
[ 0.629543] GICv3: CPU15: found redistributor 701 region 0:0x00000000063e0000
[ 0.629556] GICv3: CPU15: using allocated LPI pending table @0x0000002178e50000
[ 0.629571] CPU15: Booted secondary processor 0x0000000701 [0x410fd083]
[ 0.629684] smp: Brought up 1 node, 16 CPUs
[ 0.931457] SMP: Total of 16 processors activated.
[ 0.934986] CPU features: detected: 32-bit EL0 Support
[ 0.938858] CPU features: detected: CRC32 instructions
[ 0.947732] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[ 0.954876] CPU: All CPU(s) started at EL2
[ 0.957748] alternatives: patching kernel code
[ 0.961954] devtmpfs: initialized
[ 0.968138] random: get_random_u32 called from bucket_table_alloc.isra.22+0x88/0x1e0 with crng_init=0
[ 0.976604] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.985153] futex hash table entries: 4096 (order: 7, 524288 bytes, linear)
[ 0.991643] pinctrl core: initialized pinctrl subsystem
[ 0.996213] thermal_sys: Registered thermal governor 'step_wise'
[ 0.996473] DMI not present or invalid.
[ 1.004023] NET: Registered protocol family 16
[ 1.008239] DMA: preallocated 256 KiB pool for atomic allocations
[ 1.013102] audit: initializing netlink subsys (disabled)
[ 1.017340] audit: type=2000 audit(0.828:1): state=initialized audit_enabled=0 res=1
[ 1.023873] cpuidle: using governor ladder
[ 1.026734] cpuidle: using governor menu
[ 1.029477] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 1.035332] Serial: AMBA PL011 UART driver
[ 1.039319] Machine: SolidRun LX2160A Clearfog CX
[ 1.042751] SoC family: QorIQ LX2160A
[ 1.045135] SoC ID: svr:0x87361010, Revision: 1.0
[ 1.049775] 21c0000.serial: ttyAMA0 at MMIO 0x21c0000 (irq = 17, base_baud = 0) is a SBSA
[ 1.056765] printk: console [ttyAMA0] enabled
[ 1.062890] printk: bootconsole [pl11] disabled
[ 1.069745] 21d0000.serial: ttyAMA1 at MMIO 0x21d0000 (irq = 18, base_baud = 0) is a SBSA
[ 1.083284] fsl_mc_bus 80c000000.fsl-mc: MC firmware version: 10.18.0
[ 1.091046] fsl_mc_dprc dprc.1: DMA mask not set
[ 1.104098] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[ 1.109500] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
[ 1.114906] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 1.120298] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
[ 1.127238] cryptd: max_cpu_qlen set to 1000
[ 1.132187] iommu: Default domain type: Translated (set via kernel command line)
[ 1.138411] vgaarb: loaded
[ 1.140045] SCSI subsystem initialized
[ 1.142660] libata version 3.00 loaded.
[ 1.142830] usbcore: registered new interface driver usbfs
[ 1.147050] usbcore: registered new interface driver hub
[ 1.151152] usbcore: registered new device driver usb
[ 1.155269] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported
[ 1.161373] i2c i2c-0: IMX I2C adapter registered
[ 1.164914] imx-i2c 2020000.i2c: can't get pinctrl, bus recovery not supported
[ 1.170923] i2c i2c-1: IMX I2C adapter registered
[ 1.174438] imx-i2c 2040000.i2c: can't get pinctrl, bus recovery not supported
[ 1.180489] i2c i2c-2: IMX I2C adapter registered
[ 1.184034] pps_core: LinuxPPS API ver. 1 registered
[ 1.187711] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 1.195563] PTP clock support registered
[ 1.198926] clocksource: Switched to clocksource arch_sys_counter
[ 1.409271] VFS: Disk quotas dquot_6.6.0
[ 1.411929] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.423147] NET: Registered protocol family 2
[ 1.426524] tcp_listen_portaddr_hash hash table entries: 4096 (order: 6, 294912 bytes, linear)
[ 1.434212] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 1.441038] TCP bind hash table entries: 65536 (order: 10, 4194304 bytes, linear)
[ 1.452946] TCP: Hash tables configured (established 65536 bind 65536)
[ 1.458362] UDP hash table entries: 4096 (order: 7, 655360 bytes, linear)
[ 1.464637] UDP-Lite hash table entries: 4096 (order: 7, 655360 bytes, linear)
[ 1.471476] NET: Registered protocol family 1
[ 1.474948] RPC: Registered named UNIX socket transport module.
[ 1.479561] RPC: Registered udp transport module.
[ 1.482958] RPC: Registered tcp transport module.
[ 1.486348] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.491485] PCI: CLS 0 bytes, default 64
[ 1.495248] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available
[ 1.502280] kvm: Limiting the IPA size due to kernel Virtual Address limit
[ 1.507851] kvm [1]: IPA Size Limit: 43bits
[ 1.511572] kvm [1]: vgic-v2@c0e0000
[ 1.513851] kvm [1]: GIC system register CPU interface enabled
[ 1.518687] kvm [1]: vgic interrupt IRQ1
[ 1.521608] kvm [1]: Hyp mode initialized successfully
[ 1.535818] workingset: timestamp_bits=46 max_order=21 bucket_order=0
[ 1.549175] NFS: Registering the id_resolver key type
[ 1.552967] Key type id_resolver registered
[ 1.555844] Key type id_legacy registered
[ 1.558661] fuse: init (API version 7.31)
[ 1.561605] 9p: Installing v9fs 9p2000 file system support
[ 1.566505] io scheduler mq-deadline registered
[ 1.569734] io scheduler kyber registered
[ 1.573894] layerscape-pcie-gen4 3600000.pcie: host bridge /soc/pcie@3600000 ranges:
[ 1.580351] layerscape-pcie-gen4 3600000.pcie: MEM 0x9040000000..0x907fffffff -> 0x0040000000
[ 1.588204] layerscape-pcie-gen4 3600000.pcie: PCI host bridge to bus 0000:00
[ 1.594036] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.598216] pci_bus 0000:00: root bus resource [mem 0x9040000000-0x907fffffff] (bus address [0x40000000-0x7fffffff])
[ 1.607459] pci 0000:00:00.0: [1957:8d90] type 01 class 0x060400
[ 1.612198] pci 0000:00:00.0: enabling Extended Tags
[ 1.615912] pci 0000:00:00.0: supports D1 D2
[ 1.618869] pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.624897] pci 0000:01:00.0: [1cc1:8201] type 00 class 0x010802
[ 1.629666] pci 0000:01:00.0: reg 0x10: [mem 0x9040000000-0x9040003fff 64bit]
[ 1.646977] pci 0000:00:00.0: up support 3 enabled 0
[ 1.650628] pci 0000:00:00.0: dn support 2 enabled 0
[ 1.654743] pci 0000:00:00.0: BAR 8: assigned [mem 0x9040000000-0x90400fffff]
[ 1.660577] pci 0000:01:00.0: BAR 0: assigned [mem 0x9040000000-0x9040003fff 64bit]
[ 1.666945] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 1.670859] pci 0000:00:00.0: bridge window [mem 0x9040000000-0x90400fffff]
[ 1.676698] pci 0000:00:00.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256
[ 1.683858] pci 0000:01:00.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256
[ 1.691047] pcieport 0000:00:00.0: PCIe capabilities: 0x13
[ 1.695230] pcieport 0000:00:00.0: init_service_irqs: -19
[ 1.699429] layerscape-pcie-gen4 3800000.pcie: host bridge /soc/pcie@3800000 ranges:
[ 1.705877] layerscape-pcie-gen4 3800000.pcie: MEM 0xa040000000..0xa07fffffff -> 0x0040000000
[ 1.713713] layerscape-pcie-gen4 3800000.pcie: PCI host bridge to bus 0001:00
[ 1.719544] pci_bus 0001:00: root bus resource [bus 00-ff]
[ 1.723724] pci_bus 0001:00: root bus resource [mem 0xa040000000-0xa07fffffff] (bus address [0x40000000-0x7fffffff])
[ 1.732950] pci 0001:00:00.0: [1957:8d90] type 01 class 0x060400
[ 1.737694] pci 0001:00:00.0: enabling Extended Tags
[ 1.741407] pci 0001:00:00.0: supports D1 D2
[ 1.744371] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.750511] pci 0001:01:00.0: [15b3:6750] type 00 class 0x020000
[ 1.755600] pci 0001:01:00.0: reg 0x10: [mem 0xa040000000-0xa0400fffff 64bit]
[ 1.761632] pci 0001:01:00.0: reg 0x18: [mem 0xa040800000-0xa040ffffff 64bit pref]
[ 1.768286] pci 0001:01:00.0: reg 0x30: [mem 0xa041000000-0xa0410fffff pref]
[ 1.787013] pci 0001:00:00.0: up support 3 enabled 0
[ 1.790665] pci 0001:00:00.0: dn support 1 enabled 0
[ 1.794787] pci 0001:00:00.0: BAR 9: assigned [mem 0xa040000000-0xa0407fffff 64bit pref]
[ 1.801572] pci 0001:00:00.0: BAR 8: assigned [mem 0xa040800000-0xa0409fffff]
[ 1.807404] pci 0001:01:00.0: BAR 2: assigned [mem 0xa040000000-0xa0407fffff 64bit pref]
[ 1.814316] pci 0001:01:00.0: BAR 0: assigned [mem 0xa040800000-0xa0408fffff 64bit]
[ 1.820793] pci 0001:01:00.0: BAR 6: assigned [mem 0xa040900000-0xa0409fffff pref]
[ 1.827056] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
[ 1.830977] pci 0001:00:00.0: bridge window [mem 0xa040800000-0xa0409fffff]
[ 1.836806] pci 0001:00:00.0: bridge window [mem 0xa040000000-0xa0407fffff 64bit pref]
[ 1.843601] pci 0001:00:00.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256
[ 1.850903] pci 0001:01:00.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256
[ 1.858079] pcieport 0001:00:00.0: PCIe capabilities: 0x13
[ 1.862260] pcieport 0001:00:00.0: init_service_irqs: -19
[ 1.867322] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.874084] arm-smmu 5000000.iommu: probing hardware configuration...
[ 1.879225] arm-smmu 5000000.iommu: SMMUv2 with:
[ 1.882529] arm-smmu 5000000.iommu: stage 1 translation
[ 1.886534] arm-smmu 5000000.iommu: stage 2 translation
[ 1.890539] arm-smmu 5000000.iommu: nested translation
[ 1.894457] arm-smmu 5000000.iommu: coherent table walk
[ 1.898461] arm-smmu 5000000.iommu: (IDR0.CTTW overridden by FW configuration)
[ 1.904464] arm-smmu 5000000.iommu: stream matching with 128 register groups
[ 1.910294] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only)
[ 1.915519] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000
[ 1.920653] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA
[ 1.925786] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA
[ 1.946137] loop: module loaded
[ 1.948871] nvme nvme0: pci function 0000:01:00.0
[ 1.952710] ahci-qoriq 3200000.sata: 3200000.sata supply ahci not found, using dummy regulator
[ 1.960072] ahci-qoriq 3200000.sata: 3200000.sata supply phy not found, using dummy regulator
[ 1.967335] ahci-qoriq 3200000.sata: 3200000.sata supply target not found, using dummy regulator
[ 1.974957] ahci-qoriq 3200000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[ 1.982613] ahci-qoriq 3200000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst
[ 1.991486] scsi host0: ahci-qoriq
[ 1.993859] ata1: SATA max UDMA/133 mmio [mem 0x03200000-0x0320ffff] port 0x100 irq 24
[ 2.000561] ahci-qoriq 3210000.sata: 3210000.sata supply ahci not found, using dummy regulator
[ 2.007916] ahci-qoriq 3210000.sata: 3210000.sata supply phy not found, using dummy regulator
[ 2.015194] ahci-qoriq 3210000.sata: 3210000.sata supply target not found, using dummy regulator
[ 2.022788] ahci-qoriq 3210000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[ 2.030443] ahci-qoriq 3210000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst
[ 2.039256] scsi host1: ahci-qoriq
[ 2.041507] ata2: SATA max UDMA/133 mmio [mem 0x03210000-0x0321ffff] port 0x100 irq 25
[ 2.048196] ahci-qoriq 3220000.sata: 3220000.sata supply ahci not found, using dummy regulator
[ 2.055550] ahci-qoriq 3220000.sata: 3220000.sata supply phy not found, using dummy regulator
[ 2.062811] ahci-qoriq 3220000.sata: 3220000.sata supply target not found, using dummy regulator
[ 2.070378] ahci-qoriq 3220000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[ 2.078032] ahci-qoriq 3220000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst
[ 2.084600] nvme nvme0: 15/0/0 default/read/poll queues
[ 2.086837] scsi host2: ahci-qoriq
[ 2.092574] ata3: SATA max UDMA/133 mmio [mem 0x03220000-0x0322ffff] port 0x100 irq 26
[ 2.092925] nvme0n1: p1 p2
[ 2.099262] ahci-qoriq 3230000.sata: 3230000.sata supply ahci not found, using dummy regulator
[ 2.108028] ahci-qoriq 3230000.sata: 3230000.sata supply phy not found, using dummy regulator
[ 2.115290] ahci-qoriq 3230000.sata: 3230000.sata supply target not found, using dummy regulator
[ 2.122864] ahci-qoriq 3230000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[ 2.130518] ahci-qoriq 3230000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst
[ 2.139348] scsi host3: ahci-qoriq
[ 2.141598] ata4: SATA max UDMA/133 mmio [mem 0x03230000-0x0323ffff] port 0x100 irq 27
[ 2.149539] libphy: Fixed MDIO Bus: probed
[ 2.152802] libphy: Freescale XGMAC MDIO Bus: probed
[ 2.156799] Qualcomm Atheros AR8035 8b96000:01: probe: irq=-1
[ 2.161245] Qualcomm Atheros AR8035 8b96000:01: probe: irq=-1
[ 2.165963] libphy: Freescale XGMAC MDIO Bus: probed
[ 2.170081] dwc3 3100000.usb: Failed to get clk 'ref': -2
[ 2.174468] dwc3 3110000.usb: Failed to get clk 'ref': -2
[ 2.179050] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.184274] ehci-platform: EHCI generic platform driver
[ 2.188257] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.193140] ohci-platform: OHCI generic platform driver
[ 2.197268] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 2.201470] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 2.207946] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010
[ 2.216064] xhci-hcd xhci-hcd.0.auto: irq 22, io mem 0x03100000
[ 2.221416] hub 1-0:1.0: USB hub found
[ 2.223894] hub 1-0:1.0: 1 port detected
[ 2.226762] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 2.230951] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 2.237305] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[ 2.242572] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 2.249744] hub 2-0:1.0: USB hub found
[ 2.252209] hub 2-0:1.0: 1 port detected
[ 2.255118] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 2.259309] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[ 2.265760] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010
[ 2.273872] xhci-hcd xhci-hcd.1.auto: irq 23, io mem 0x03110000
[ 2.279084] hub 3-0:1.0: USB hub found
[ 2.281538] hub 3-0:1.0: 1 port detected
[ 2.284380] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 2.288571] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[ 2.294930] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[ 2.300190] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 2.307363] hub 4-0:1.0: USB hub found
[ 2.309817] hub 4-0:1.0: 1 port detected
[ 2.312750] usbcore: registered new interface driver usb-storage
[ 2.317173] ata1: SATA link down (SStatus 0 SControl 300)
[ 2.317696] mousedev: PS/2 mouse device common for all mice
[ 2.331955] rtc-pcf2127-i2c 2-0051: registered as rtc0
[ 2.335876] i2c /dev entries driver
[ 2.339327] i2c i2c-0: Added multiplexed i2c bus 3
[ 2.343067] i2c i2c-0: Added multiplexed i2c bus 4
[ 2.346783] i2c i2c-0: Added multiplexed i2c bus 5
[ 2.350507] i2c i2c-0: Added multiplexed i2c bus 6
[ 2.354164] i2c i2c-0: Added multiplexed i2c bus 7
[ 2.357821] i2c i2c-0: Added multiplexed i2c bus 8
[ 2.361159] ata2: SATA link down (SStatus 0 SControl 300)
[ 2.361480] i2c i2c-0: Added multiplexed i2c bus 9
[ 2.369047] i2c i2c-0: Added multiplexed i2c bus 10
[ 2.372627] pca954x 0-0077: registered 8 multiplexed busses for I2C mux pca9547
[ 2.378783] IR NEC protocol handler initialized
[ 2.382010] IR RC5(x/sz) protocol handler initialized
[ 2.385755] IR RC6 protocol handler initialized
[ 2.388977] IR JVC protocol handler initialized
[ 2.392200] IR Sony protocol handler initialized
[ 2.395513] IR SANYO protocol handler initialized
[ 2.398903] IR Sharp protocol handler initialized
[ 2.402300] IR MCE Keyboard/mouse protocol handler initialized
[ 2.406827] IR XMP protocol handler initialized
[ 2.413367] amc6821 4-0018: Error reading configuration register, aborting.
[ 2.417180] ata3: SATA link down (SStatus 0 SControl 300)
[ 2.419034] amc6821: probe of 4-0018 failed with error -5
[ 2.427436] sdhci: Secure Digital Host Controller Interface driver
[ 2.432314] sdhci: Copyright(c) Pierre Ossman
[ 2.435384] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.461157] ata4: SATA link down (SStatus 0 SControl 300)
[ 2.465487] mmc0: SDHCI controller on 2140000.esdhc [2140000.esdhc] using ADMA 64-bit
[ 2.494954] mmc1: SDHCI controller on 2150000.esdhc [2150000.esdhc] using ADMA 64-bit
[ 2.502071] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.507175] caam 8000000.crypto: device ID = 0x0a1a020000000000 (Era 10)
[ 2.508538] mmc0: new high speed SDHC card at address aaaa
[ 2.512572] caam 8000000.crypto: job rings = 3, qi = 1
[ 2.521006] mmcblk0: mmc0:aaaa SU04G 3.69 GiB (ro)
[ 2.525840] caam algorithms registered in /proc/crypto
[ 2.532365] caam 8000000.crypto: caam pkc algorithms registered in /proc/crypto
[ 2.539400] caam_jr 8010000.jr: registering rng-caam
[ 2.543736] usbcore: registered new interface driver usbhid
[ 2.548007] usbhid: USB HID core driver
[ 2.551148] NET: Registered protocol family 10
[ 2.554963] Segment Routing with IPv6
[ 2.557343] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 2.562313] NET: Registered protocol family 17
[ 2.565629] 9pnet: Installing 9P2000 support
[ 2.568641] Key type dns_resolver registered
[ 2.571820] registered taskstats version 1
[ 2.578646] fsl_mc_dprc dprc.1: Adding to iommu group 0
[ 2.584473] mmc1: new HS400 MMC card at address 0001
[ 2.592566] mmcblk1: mmc1:0001 DF4064 58.2 GiB
[ 2.595945] mmcblk1boot0: mmc1:0001 DF4064 partition 1 4.00 MiB
[ 2.600717] mmcblk1boot1: mmc1:0001 DF4064 partition 2 4.00 MiB
[ 2.605471] mmcblk1rpmb: mmc1:0001 DF4064 partition 3 4.00 MiB, chardev (246:0)
[ 2.612749] mmcblk1: p1 p2
[ 2.622945] usb 3-1: new high-speed USB device number 2 using xhci-hcd
[ 2.642000] fsl_dpaa2_eth dpni.0: Adding to iommu group 0
[ 2.646254] fsl_mc_dprc dprc.1: No more resources of type dpmcp left
[ 2.651688] fsl_mc_allocator dpbp.1: Adding to iommu group 0
[ 2.656161] fsl_mc_allocator dpbp.0: Adding to iommu group 0
[ 2.662117] fsl_mc_allocator dpmcp.35: Adding to iommu group 0
[ 2.667765] fsl_mc_allocator dpmcp.34: Adding to iommu group 0
[ 2.673422] fsl_mc_allocator dpmcp.33: Adding to iommu group 0
[ 2.679071] fsl_mc_allocator dpmcp.32: Adding to iommu group 0
[ 2.684267] hub 3-1:1.0: USB hub found
[ 2.684727] fsl_mc_allocator dpmcp.31: Adding to iommu group 0
[ 2.686736] hub 3-1:1.0: 4 ports detected
[ 2.692343] fsl_mc_allocator dpmcp.30: Adding to iommu group 0
[ 2.699627] fsl_mc_allocator dpmcp.29: Adding to iommu group 0
[ 2.705265] fsl_mc_allocator dpmcp.28: Adding to iommu group 0
[ 2.710952] fsl_mc_allocator dpmcp.27: Adding to iommu group 0
[ 2.716596] fsl_mc_allocator dpmcp.26: Adding to iommu group 0
[ 2.722243] fsl_mc_allocator dpmcp.25: Adding to iommu group 0
[ 2.727897] fsl_mc_allocator dpmcp.24: Adding to iommu group 0
[ 2.733550] fsl_mc_allocator dpmcp.23: Adding to iommu group 0
[ 2.739198] fsl_mc_allocator dpmcp.22: Adding to iommu group 0
[ 2.744853] fsl_mc_allocator dpmcp.21: Adding to iommu group 0
[ 2.750495] fsl_mc_allocator dpmcp.20: Adding to iommu group 0
[ 2.756161] fsl_mc_allocator dpmcp.19: Adding to iommu group 0
[ 2.761803] fsl_mc_allocator dpmcp.18: Adding to iommu group 0
[ 2.767473] fsl_mc_allocator dpmcp.17: Adding to iommu group 0
[ 2.773117] fsl_mc_allocator dpmcp.16: Adding to iommu group 0
[ 2.778768] fsl_mc_allocator dpmcp.15: Adding to iommu group 0
[ 2.782959] usb 4-1: new SuperSpeed Gen 1 USB device number 2 using xhci-hcd
[ 2.784414] fsl_mc_allocator dpmcp.14: Adding to iommu group 0
[ 2.794669] fsl_mc_allocator dpmcp.13: Adding to iommu group 0
[ 2.800309] fsl_mc_allocator dpmcp.12: Adding to iommu group 0
[ 2.805969] fsl_mc_allocator dpmcp.11: Adding to iommu group 0
[ 2.811625] fsl_mc_allocator dpmcp.10: Adding to iommu group 0
[ 2.817271] fsl_mc_allocator dpmcp.9: Adding to iommu group 0
[ 2.822845] fsl_mc_allocator dpmcp.8: Adding to iommu group 0
[ 2.828243] hub 4-1:1.0: USB hub found
[ 2.828420] fsl_mc_allocator dpmcp.7: Adding to iommu group 0
[ 2.830710] hub 4-1:1.0: 4 ports detected
[ 2.836276] fsl_mc_allocator dpmcp.6: Adding to iommu group 0
[ 2.843415] fsl_mc_allocator dpmcp.5: Adding to iommu group 0
[ 2.848975] fsl_mc_allocator dpmcp.4: Adding to iommu group 0
[ 2.851038] random: fast init done
[ 2.854534] fsl_mc_allocator dpmcp.3: Adding to iommu group 0
[ 2.861060] fsl_mc_allocator dpmcp.2: Adding to iommu group 0
[ 2.866622] fsl_mc_allocator dpmcp.1: Adding to iommu group 0
[ 2.874308] fsl_mc_dpio dpio.15: Adding to iommu group 0
[ 2.882022] fsl_mc_dpio dpio.15: probed
[ 2.888261] fsl_mc_dpio dpio.14: Adding to iommu group 0
[ 2.895912] fsl_mc_dpio dpio.14: probed
[ 2.902061] fsl_mc_dpio dpio.13: Adding to iommu group 0
[ 2.909710] fsl_mc_dpio dpio.13: probed
[ 2.915939] fsl_mc_dpio dpio.12: Adding to iommu group 0
[ 2.923591] fsl_mc_dpio dpio.12: probed
[ 2.929752] fsl_mc_dpio dpio.11: Adding to iommu group 0
[ 2.937396] fsl_mc_dpio dpio.11: probed
[ 2.943628] fsl_mc_dpio dpio.10: Adding to iommu group 0
[ 2.951283] fsl_mc_dpio dpio.10: probed
[ 2.957446] fsl_mc_dpio dpio.9: Adding to iommu group 0
[ 2.965012] fsl_mc_dpio dpio.9: probed
[ 2.971167] fsl_mc_dpio dpio.8: Adding to iommu group 0
[ 2.978776] fsl_mc_dpio dpio.8: probed
[ 2.984923] fsl_mc_dpio dpio.7: Adding to iommu group 0
[ 2.992537] fsl_mc_dpio dpio.7: probed
[ 2.998684] fsl_mc_dpio dpio.6: Adding to iommu group 0
[ 3.006299] fsl_mc_dpio dpio.6: probed
[ 3.012440] fsl_mc_dpio dpio.5: Adding to iommu group 0
[ 3.020064] fsl_mc_dpio dpio.5: probed
[ 3.026190] fsl_mc_dpio dpio.4: Adding to iommu group 0
[ 3.033754] fsl_mc_dpio dpio.4: probed
[ 3.038937] usb 3-1.3: new high-speed USB device number 3 using xhci-hcd
[ 3.039844] fsl_mc_dpio dpio.3: Adding to iommu group 0
[ 3.051890] fsl_mc_dpio dpio.3: probed
[ 3.058009] fsl_mc_dpio dpio.2: Adding to iommu group 0
[ 3.065609] fsl_mc_dpio dpio.2: probed
[ 3.071763] fsl_mc_dpio dpio.1: Adding to iommu group 0
[ 3.079384] fsl_mc_dpio dpio.1: probed
[ 3.085521] fsl_mc_dpio dpio.0: Adding to iommu group 0
[ 3.093136] fsl_mc_dpio dpio.0: probed
[ 3.096201] fsl_mc_allocator dpcon.31: Adding to iommu group 0
[ 3.100196] hub 3-1.3:1.0: USB hub found
[ 3.100860] fsl_mc_allocator dpcon.30: Adding to iommu group 0
[ 3.103374] hub 3-1.3:1.0: 4 ports detected
[ 3.107983] fsl_mc_allocator dpcon.29: Adding to iommu group 0
[ 3.115381] fsl_mc_allocator dpcon.28: Adding to iommu group 0
[ 3.120030] fsl_mc_allocator dpcon.27: Adding to iommu group 0
[ 3.124682] fsl_mc_allocator dpcon.26: Adding to iommu group 0
[ 3.129333] fsl_mc_allocator dpcon.25: Adding to iommu group 0
[ 3.133987] fsl_mc_allocator dpcon.24: Adding to iommu group 0
[ 3.138642] fsl_mc_allocator dpcon.23: Adding to iommu group 0
[ 3.143294] fsl_mc_allocator dpcon.22: Adding to iommu group 0
[ 3.147946] fsl_mc_allocator dpcon.21: Adding to iommu group 0
[ 3.152597] fsl_mc_allocator dpcon.20: Adding to iommu group 0
[ 3.157250] fsl_mc_allocator dpcon.19: Adding to iommu group 0
[ 3.161903] fsl_mc_allocator dpcon.18: Adding to iommu group 0
[ 3.166559] fsl_mc_allocator dpcon.17: Adding to iommu group 0
[ 3.171217] fsl_mc_allocator dpcon.16: Adding to iommu group 0
[ 3.175871] fsl_mc_allocator dpcon.15: Adding to iommu group 0
[ 3.180533] fsl_mc_allocator dpcon.14: Adding to iommu group 0
[ 3.185188] fsl_mc_allocator dpcon.13: Adding to iommu group 0
[ 3.189844] fsl_mc_allocator dpcon.12: Adding to iommu group 0
[ 3.194499] fsl_mc_allocator dpcon.11: Adding to iommu group 0
[ 3.199153] fsl_mc_allocator dpcon.10: Adding to iommu group 0
[ 3.203810] fsl_mc_allocator dpcon.9: Adding to iommu group 0
[ 3.208385] fsl_mc_allocator dpcon.8: Adding to iommu group 0
[ 3.212956] fsl_mc_allocator dpcon.7: Adding to iommu group 0
[ 3.217526] fsl_mc_allocator dpcon.6: Adding to iommu group 0
[ 3.222096] fsl_mc_allocator dpcon.5: Adding to iommu group 0
[ 3.226667] fsl_mc_allocator dpcon.4: Adding to iommu group 0
[ 3.231237] fsl_mc_allocator dpcon.3: Adding to iommu group 0
[ 3.235812] fsl_mc_allocator dpcon.2: Adding to iommu group 0
[ 3.240383] fsl_mc_allocator dpcon.1: Adding to iommu group 0
[ 3.244955] fsl_mc_allocator dpcon.0: Adding to iommu group 0
[ 3.252565] fsl_mc_dprc dprc.1: DPRC device bound to driver
[ 3.257032] libphy: SFP I2C Bus: probed
[ 3.259658] sfp sfp-0: Host maximum power 2.0W
[ 3.262929] sfp sfp-0: No tx_disable pin: SFP modules will always be emitting.
[ 3.269061] libphy: SFP I2C Bus: probed
[ 3.271642] sfp sfp-1: Host maximum power 2.0W
[ 3.274884] sfp sfp-1: No tx_disable pin: SFP modules will always be emitting.
[ 3.280979] libphy: SFP I2C Bus: probed
[ 3.283559] sfp sfp-2: Host maximum power 2.0W
[ 3.286819] sfp sfp-2: No tx_disable pin: SFP modules will always be emitting.
[ 3.292948] libphy: SFP I2C Bus: probed
[ 3.295529] sfp sfp-3: Host maximum power 2.0W
[ 3.298768] sfp sfp-3: No tx_disable pin: SFP modules will always be emitting.
[ 3.456609] fsl_dpaa2_eth dpni.0 (unnamed net_device) (uninitialized): PHY [8b96000:01] driver [Qualcomm Atheros AR8035] (irq=POLL)
[ 3.467153] fsl_dpaa2_eth dpni.0 (unnamed net_device) (uninitialized): phy: setting supported 000,00000200,000062ea advertising 000,00000200,000062ea
[ 3.468341] fsl_dpaa2_eth dpni.0: Probed interface eth0
[ 3.472672] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 3.479780] rtc-pcf2127-i2c 2-0051: setting system clock to 2020-02-28T09:56:18 UTC (1582883778)
[ 3.490224] EXT4-fs (nvme0n1p2): mounted filesystem with ordered data mode. Opts: (null)
[ 3.497082] VFS: Mounted root (ext4 filesystem) readonly on device 259:2.
[ 3.503193] devtmpfs: mounted
[ 3.505079] Freeing unused kernel memory: 960K
[ 3.534993] Run /sbin/init as init process
When asking for more network interfaces, more "Adding to iommu group"
messages get spat out:
[ 446.040825] fsl_dpaa2_eth dpni.1: Adding to iommu group 0
[ 446.201254] libphy: Freescale XGMAC MDIO Bus: probed
[ 446.206552] fsl_dpaa2_eth dpni.1: Probed interface eth1
[ 446.210715] fsl_mc_allocator dpbp.2: Adding to iommu group 0
[ 446.216838] fsl_mc_allocator dpmcp.36: Adding to iommu group 0
[ 446.224808] fsl_mc_allocator dpcon.47: Adding to iommu group 0
[ 446.229935] fsl_mc_allocator dpcon.46: Adding to iommu group 0
[ 446.234685] fsl_mc_allocator dpcon.45: Adding to iommu group 0
[ 446.239431] fsl_mc_allocator dpcon.44: Adding to iommu group 0
[ 446.244179] fsl_mc_allocator dpcon.43: Adding to iommu group 0
[ 446.251725] fsl_mc_allocator dpcon.42: Adding to iommu group 0
[ 446.258952] fsl_mc_allocator dpcon.41: Adding to iommu group 0
[ 446.263666] fsl_mc_allocator dpcon.40: Adding to iommu group 0
[ 446.268377] fsl_mc_allocator dpcon.39: Adding to iommu group 0
[ 446.273086] fsl_mc_allocator dpcon.38: Adding to iommu group 0
[ 446.277814] fsl_mc_allocator dpcon.37: Adding to iommu group 0
[ 446.282517] fsl_mc_allocator dpcon.36: Adding to iommu group 0
[ 446.287228] fsl_mc_allocator dpcon.35: Adding to iommu group 0
[ 446.291935] fsl_mc_allocator dpcon.34: Adding to iommu group 0
[ 446.296641] fsl_mc_allocator dpcon.33: Adding to iommu group 0
[ 446.301354] fsl_mc_allocator dpcon.32: Adding to iommu group 0
[ 446.893939] fsl_dpaa2_eth dpni.2: Adding to iommu group 0
[ 447.052868] libphy: Freescale XGMAC MDIO Bus: probed
[ 447.058223] fsl_dpaa2_eth dpni.2: Probed interface eth2
[ 447.062425] fsl_mc_allocator dpbp.3: Adding to iommu group 0
[ 447.068813] fsl_mc_allocator dpmcp.37: Adding to iommu group 0
[ 447.074280] fsl_mc_allocator dpcon.63: Adding to iommu group 0
[ 447.078995] fsl_mc_allocator dpcon.62: Adding to iommu group 0
[ 447.088690] fsl_mc_allocator dpcon.61: Adding to iommu group 0
[ 447.093639] fsl_mc_allocator dpcon.60: Adding to iommu group 0
[ 447.098369] fsl_mc_allocator dpcon.59: Adding to iommu group 0
[ 447.103089] fsl_mc_allocator dpcon.58: Adding to iommu group 0
[ 447.107811] fsl_mc_allocator dpcon.57: Adding to iommu group 0
[ 447.112525] fsl_mc_allocator dpcon.56: Adding to iommu group 0
[ 447.117244] fsl_mc_allocator dpcon.55: Adding to iommu group 0
[ 447.121962] fsl_mc_allocator dpcon.54: Adding to iommu group 0
[ 447.126680] fsl_mc_allocator dpcon.53: Adding to iommu group 0
[ 447.131392] fsl_mc_allocator dpcon.52: Adding to iommu group 0
[ 447.136107] fsl_mc_allocator dpcon.51: Adding to iommu group 0
[ 447.140820] fsl_mc_allocator dpcon.50: Adding to iommu group 0
[ 447.145535] fsl_mc_allocator dpcon.49: Adding to iommu group 0
[ 447.150249] fsl_mc_allocator dpcon.48: Adding to iommu group 0
[ 447.710694] fsl_dpaa2_eth dpni.3: Adding to iommu group 0
[ 447.888120] libphy: Freescale XGMAC MDIO Bus: probed
[ 447.893479] fsl_dpaa2_eth dpni.3: Probed interface eth3
[ 447.897740] fsl_mc_allocator dpbp.4: Adding to iommu group 0
[ 447.904488] fsl_mc_allocator dpmcp.38: Adding to iommu group 0
[ 447.909994] fsl_mc_allocator dpcon.79: Adding to iommu group 0
[ 447.914717] fsl_mc_allocator dpcon.78: Adding to iommu group 0
[ 447.919852] fsl_mc_allocator dpcon.77: Adding to iommu group 0
[ 447.924720] fsl_mc_allocator dpcon.76: Adding to iommu group 0
[ 447.931979] fsl_mc_allocator dpcon.75: Adding to iommu group 0
[ 447.939172] fsl_mc_allocator dpcon.74: Adding to iommu group 0
[ 447.943886] fsl_mc_allocator dpcon.73: Adding to iommu group 0
[ 447.948604] fsl_mc_allocator dpcon.72: Adding to iommu group 0
[ 447.953319] fsl_mc_allocator dpcon.71: Adding to iommu group 0
[ 447.958035] fsl_mc_allocator dpcon.70: Adding to iommu group 0
[ 447.965445] fsl_mc_allocator dpcon.69: Adding to iommu group 0
[ 447.972653] fsl_mc_allocator dpcon.68: Adding to iommu group 0
[ 447.977376] fsl_mc_allocator dpcon.67: Adding to iommu group 0
[ 447.982097] fsl_mc_allocator dpcon.66: Adding to iommu group 0
[ 447.986816] fsl_mc_allocator dpcon.65: Adding to iommu group 0
[ 447.991532] fsl_mc_allocator dpcon.64: Adding to iommu group 0
[ 448.737198] fsl_dpaa2_eth dpni.4: Adding to iommu group 0
[ 448.894480] libphy: Freescale XGMAC MDIO Bus: probed
[ 448.899785] fsl_dpaa2_eth dpni.4: Probed interface eth4
[ 448.904077] fsl_mc_allocator dpbp.5: Adding to iommu group 0
[ 448.909817] fsl_mc_allocator dpmcp.39: Adding to iommu group 0
[ 448.915340] fsl_mc_allocator dpcon.95: Adding to iommu group 0
[ 448.920068] fsl_mc_allocator dpcon.94: Adding to iommu group 0
[ 448.924789] fsl_mc_allocator dpcon.93: Adding to iommu group 0
[ 448.929689] fsl_mc_allocator dpcon.92: Adding to iommu group 0
[ 448.934436] fsl_mc_allocator dpcon.91: Adding to iommu group 0
[ 448.939159] fsl_mc_allocator dpcon.90: Adding to iommu group 0
[ 448.943882] fsl_mc_allocator dpcon.89: Adding to iommu group 0
[ 448.948607] fsl_mc_allocator dpcon.88: Adding to iommu group 0
[ 448.953327] fsl_mc_allocator dpcon.87: Adding to iommu group 0
[ 448.958050] fsl_mc_allocator dpcon.86: Adding to iommu group 0
[ 448.962771] fsl_mc_allocator dpcon.85: Adding to iommu group 0
[ 448.967499] fsl_mc_allocator dpcon.84: Adding to iommu group 0
[ 448.972219] fsl_mc_allocator dpcon.83: Adding to iommu group 0
[ 448.976941] fsl_mc_allocator dpcon.82: Adding to iommu group 0
[ 448.981669] fsl_mc_allocator dpcon.81: Adding to iommu group 0
[ 448.986391] fsl_mc_allocator dpcon.80: Adding to iommu group 0
# dmesg |grep 'Adding to iommu' | wc -l
164
# dmesg |grep -v 'Adding to iommu' | wc -l
551
So, 23% of the kernel messages on this platform are "Adding to iommu",
which is excessive.
--
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up
According to speedtest.net: 11.9Mbps down 500kbps up
_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH] iommu: silence iommu group prints
2020-02-28 10:06 ` Russell King - ARM Linux admin
@ 2020-02-28 18:32 ` Robin Murphy
2020-03-02 11:48 ` Laurentiu Tudor
2020-03-03 14:18 ` Laurentiu Tudor
0 siblings, 2 replies; 24+ messages in thread
From: Robin Murphy @ 2020-02-28 18:32 UTC (permalink / raw)
To: Russell King - ARM Linux admin, Laurentiu Tudor; +Cc: iommu
[ +Laurentiu ]
Hi Russell,
Thanks for sharing a log, now I properly understand what's up... further
comments at the end (for context).
On 28/02/2020 10:06 am, Russell King - ARM Linux admin wrote:
> On Fri, Feb 28, 2020 at 09:33:40AM +0000, John Garry wrote:
>> On 28/02/2020 02:16, Lu Baolu wrote:
>>> Hi,
>>>
>>> On 2020/2/27 19:57, Russell King wrote:
>>>> On the LX2160A, there are lots (about 160) of IOMMU messages produced
>>>> during boot; this is excessive. Reduce the severity of these messages
>>>> to debug level.
>>>>
>>>> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
>>>> ---
>>>> drivers/iommu/iommu.c | 4 ++--
>>>> 1 file changed, 2 insertions(+), 2 deletions(-)
>>>>
>>>> diff --git a/drivers/iommu/iommu.c b/drivers/iommu/iommu.c
>>>> index 3ead597e1c57..304281ec623b 100644
>>>> --- a/drivers/iommu/iommu.c
>>>> +++ b/drivers/iommu/iommu.c
>>>> @@ -741,7 +741,7 @@ int iommu_group_add_device(struct iommu_group
>>>> *group, struct device *dev)
>>>> trace_add_device_to_group(group->id, dev);
>>>> - dev_info(dev, "Adding to iommu group %d\n", group->id);
>>>> + dev_dbg(dev, "Adding to iommu group %d\n", group->id);
>>>
>>> I'm not strongly against this. But to me this message seems to be a good
>>> indicator that a device was probed successfully by the iommu subsystem.
>>> Keeping it in the default kernel message always helps to the kernel
>>> debugging.
>>>
>>
>> I would tend to agree.
>
> Here's the boot messages. Notice how many of these "Adding to iommu
> group" messages there are:
>
> [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083]
> [ 0.000000] Linux version 5.5.0+ (rmk@rmk-PC) (gcc version 4.9.2 (GCC)) #655 SMP PREEMPT Fri Feb 28 09:54:47 GMT 2020
> [ 0.000000] Machine model: SolidRun LX2160A Clearfog CX
> [ 0.000000] earlycon: pl11 at MMIO32 0x00000000021c0000 (options '')
> [ 0.000000] printk: bootconsole [pl11] enabled
> [ 0.000000] efi: Getting EFI parameters from FDT:
> [ 0.000000] efi: UEFI not found.
> [ 0.000000] cma: Reserved 32 MiB at 0x00000000f9c00000
> [ 0.000000] On node 0 totalpages: 1555968
> [ 0.000000] DMA zone: 4096 pages used for memmap
> [ 0.000000] DMA zone: 0 pages reserved
> [ 0.000000] DMA zone: 262144 pages, LIFO batch:63
> [ 0.000000] DMA32 zone: 3832 pages used for memmap
> [ 0.000000] DMA32 zone: 245248 pages, LIFO batch:63
> [ 0.000000] Normal zone: 16384 pages used for memmap
> [ 0.000000] Normal zone: 1048576 pages, LIFO batch:63
> [ 0.000000] psci: probing for conduit method from DT.
> [ 0.000000] psci: PSCIv1.1 detected in firmware.
> [ 0.000000] psci: Using standard PSCI v0.2 function IDs
> [ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
> [ 0.000000] psci: SMC Calling Convention v1.1
> [ 0.000000] percpu: Embedded 31 pages/cpu s88968 r8192 d29816 u126976
> [ 0.000000] pcpu-alloc: s88968 r8192 d29816 u126976 alloc=31*4096
> [ 0.000000] pcpu-alloc: [0] 00 [0] 01 [0] 02 [0] 03 [0] 04 [0] 05 [0] 06 [0] 07
> [ 0.000000] pcpu-alloc: [0] 08 [0] 09 [0] 10 [0] 11 [0] 12 [0] 13 [0] 14 [0] 15
> [ 0.000000] Detected PIPT I-cache on CPU0
> [ 0.000000] CPU features: detected: GIC system register CPU interface
> [ 0.000000] CPU features: detected: EL2 vector hardening
> [ 0.000000] Speculative Store Bypass Disable mitigation not required
> [ 0.000000] CPU features: detected: ARM erratum 1319367
> [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1531656
> [ 0.000000] Kernel command line: console=ttyAMA0,115200 root=PARTUUID=c7837e2f-02 rootwait earlycon=pl011,mmio32,0x21c0000 ramdisk_size=0 pci=pcie_bus_perf arm_smmu.disable_bypass=0 iommu.passthrough=0
> [ 0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
> [ 0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
> [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
> [ 0.000000] software IO TLB: mapped [mem 0xbbfff000-0xbffff000] (64MB)
> [ 0.000000] Memory: 5991500K/6223872K available (10172K kernel code, 1376K rwdata, 3888K rodata, 960K init, 4326K bss, 199604K reserved, 32768K cma-reserved)
> [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=16, Nodes=1
> [ 0.000000] rcu: Preemptible hierarchical RCU implementation.
> [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=16.
> [ 0.000000] Tasks RCU enabled.
> [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
> [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=16
> [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
> [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
> [ 0.000000] GICv3: 256 SPIs implemented
> [ 0.000000] GICv3: 0 Extended SPIs implemented
> [ 0.000000] GICv3: Distributor has no Range Selector support
> [ 0.000000] GICv3: 16 PPIs implemented
> [ 0.000000] GICv3: no VLPI support, no direct LPI support
> [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006200000
> [ 0.000000] ITS [mem 0x06020000-0x0603ffff]
> [ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices @2178d00000 (flat, esz 8, psz 64K, shr 0)
> [ 0.000000] ITS: using cache flushing for cmd queue
> [ 0.000000] GICv3: using LPI property table @0x0000002178cd0000
> [ 0.000000] GIC: using cache flushing for LPI property table
> [ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000002178ce0000
> [ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys).
> [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c409fb33, max_idle_ns: 440795203156 ns
> [ 0.000002] sched_clock: 56 bits at 25MHz, resolution 39ns, wraps every 4398046511103ns
> [ 0.006921] Console: colour dummy device 80x25
> [ 0.010093] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
> [ 0.016605] ... MAX_LOCKDEP_SUBCLASSES: 8
> [ 0.019421] ... MAX_LOCK_DEPTH: 48
> [ 0.022329] ... MAX_LOCKDEP_KEYS: 8192
> [ 0.025408] ... CLASSHASH_SIZE: 4096
> [ 0.028491] ... MAX_LOCKDEP_ENTRIES: 32768
> [ 0.031659] ... MAX_LOCKDEP_CHAINS: 65536
> [ 0.034830] ... CHAINHASH_SIZE: 32768
> [ 0.037997] memory used by lock dependency info: 3509 kB
> [ 0.042135] per task-struct memory footprint: 1920 bytes
> [ 0.046292] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000)
> [ 0.055443] pid_max: default: 32768 minimum: 301
> [ 0.058844] LSM: Security Framework initializing
> [ 0.062241] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
> [ 0.068602] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
> [ 0.099452] ASID allocator initialised with 32768 entries
> [ 0.111615] rcu: Hierarchical SRCU implementation.
> [ 0.119672] Platform MSI: gic-its@6020000 domain created
> [ 0.123765] PCI/MSI: /interrupt-controller@6000000/gic-its@6020000 domain created
> [ 0.130045] fsl-mc MSI: /interrupt-controller@6000000/gic-its@6020000 domain created
> [ 0.136572] EFI services will not be available.
> [ 0.148587] smp: Bringing up secondary CPUs ...
> [ 0.180732] Detected PIPT I-cache on CPU1
> [ 0.180749] GICv3: CPU1: found redistributor 1 region 0:0x0000000006220000
> [ 0.180761] GICv3: CPU1: using allocated LPI pending table @0x0000002178cf0000
> [ 0.180781] CPU1: Booted secondary processor 0x0000000001 [0x410fd083]
> [ 0.212781] Detected PIPT I-cache on CPU2
> [ 0.212797] GICv3: CPU2: found redistributor 100 region 0:0x0000000006240000
> [ 0.212810] GICv3: CPU2: using allocated LPI pending table @0x0000002178d80000
> [ 0.212830] CPU2: Booted secondary processor 0x0000000100 [0x410fd083]
> [ 0.244832] Detected PIPT I-cache on CPU3
> [ 0.244844] GICv3: CPU3: found redistributor 101 region 0:0x0000000006260000
> [ 0.244855] GICv3: CPU3: using allocated LPI pending table @0x0000002178d90000
> [ 0.244871] CPU3: Booted secondary processor 0x0000000101 [0x410fd083]
> [ 0.276894] Detected PIPT I-cache on CPU4
> [ 0.276910] GICv3: CPU4: found redistributor 200 region 0:0x0000000006280000
> [ 0.276922] GICv3: CPU4: using allocated LPI pending table @0x0000002178da0000
> [ 0.276941] CPU4: Booted secondary processor 0x0000000200 [0x410fd083]
> [ 0.308953] Detected PIPT I-cache on CPU5
> [ 0.308966] GICv3: CPU5: found redistributor 201 region 0:0x00000000062a0000
> [ 0.308978] GICv3: CPU5: using allocated LPI pending table @0x0000002178db0000
> [ 0.308994] CPU5: Booted secondary processor 0x0000000201 [0x410fd083]
> [ 0.341009] Detected PIPT I-cache on CPU6
> [ 0.341027] GICv3: CPU6: found redistributor 300 region 0:0x00000000062c0000
> [ 0.341039] GICv3: CPU6: using allocated LPI pending table @0x0000002178dc0000
> [ 0.341058] CPU6: Booted secondary processor 0x0000000300 [0x410fd083]
> [ 0.373064] Detected PIPT I-cache on CPU7
> [ 0.373079] GICv3: CPU7: found redistributor 301 region 0:0x00000000062e0000
> [ 0.373091] GICv3: CPU7: using allocated LPI pending table @0x0000002178dd0000
> [ 0.373106] CPU7: Booted secondary processor 0x0000000301 [0x410fd083]
> [ 0.405124] Detected PIPT I-cache on CPU8
> [ 0.405143] GICv3: CPU8: found redistributor 400 region 0:0x0000000006300000
> [ 0.405156] GICv3: CPU8: using allocated LPI pending table @0x0000002178de0000
> [ 0.405175] CPU8: Booted secondary processor 0x0000000400 [0x410fd083]
> [ 0.437179] Detected PIPT I-cache on CPU9
> [ 0.437195] GICv3: CPU9: found redistributor 401 region 0:0x0000000006320000
> [ 0.437207] GICv3: CPU9: using allocated LPI pending table @0x0000002178df0000
> [ 0.437223] CPU9: Booted secondary processor 0x0000000401 [0x410fd083]
> [ 0.469240] Detected PIPT I-cache on CPU10
> [ 0.469261] GICv3: CPU10: found redistributor 500 region 0:0x0000000006340000
> [ 0.469273] GICv3: CPU10: using allocated LPI pending table @0x0000002178e00000
> [ 0.469293] CPU10: Booted secondary processor 0x0000000500 [0x410fd083]
> [ 0.501296] Detected PIPT I-cache on CPU11
> [ 0.501314] GICv3: CPU11: found redistributor 501 region 0:0x0000000006360000
> [ 0.501326] GICv3: CPU11: using allocated LPI pending table @0x0000002178e10000
> [ 0.501342] CPU11: Booted secondary processor 0x0000000501 [0x410fd083]
> [ 0.533362] Detected PIPT I-cache on CPU12
> [ 0.533385] GICv3: CPU12: found redistributor 600 region 0:0x0000000006380000
> [ 0.533397] GICv3: CPU12: using allocated LPI pending table @0x0000002178e20000
> [ 0.533418] CPU12: Booted secondary processor 0x0000000600 [0x410fd083]
> [ 0.565408] Detected PIPT I-cache on CPU13
> [ 0.565427] GICv3: CPU13: found redistributor 601 region 0:0x00000000063a0000
> [ 0.565440] GICv3: CPU13: using allocated LPI pending table @0x0000002178e30000
> [ 0.565455] CPU13: Booted secondary processor 0x0000000601 [0x410fd083]
> [ 0.597470] Detected PIPT I-cache on CPU14
> [ 0.597494] GICv3: CPU14: found redistributor 700 region 0:0x00000000063c0000
> [ 0.597507] GICv3: CPU14: using allocated LPI pending table @0x0000002178e40000
> [ 0.597527] CPU14: Booted secondary processor 0x0000000700 [0x410fd083]
> [ 0.629523] Detected PIPT I-cache on CPU15
> [ 0.629543] GICv3: CPU15: found redistributor 701 region 0:0x00000000063e0000
> [ 0.629556] GICv3: CPU15: using allocated LPI pending table @0x0000002178e50000
> [ 0.629571] CPU15: Booted secondary processor 0x0000000701 [0x410fd083]
> [ 0.629684] smp: Brought up 1 node, 16 CPUs
> [ 0.931457] SMP: Total of 16 processors activated.
> [ 0.934986] CPU features: detected: 32-bit EL0 Support
> [ 0.938858] CPU features: detected: CRC32 instructions
> [ 0.947732] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
> [ 0.954876] CPU: All CPU(s) started at EL2
> [ 0.957748] alternatives: patching kernel code
> [ 0.961954] devtmpfs: initialized
> [ 0.968138] random: get_random_u32 called from bucket_table_alloc.isra.22+0x88/0x1e0 with crng_init=0
> [ 0.976604] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
> [ 0.985153] futex hash table entries: 4096 (order: 7, 524288 bytes, linear)
> [ 0.991643] pinctrl core: initialized pinctrl subsystem
> [ 0.996213] thermal_sys: Registered thermal governor 'step_wise'
> [ 0.996473] DMI not present or invalid.
> [ 1.004023] NET: Registered protocol family 16
> [ 1.008239] DMA: preallocated 256 KiB pool for atomic allocations
> [ 1.013102] audit: initializing netlink subsys (disabled)
> [ 1.017340] audit: type=2000 audit(0.828:1): state=initialized audit_enabled=0 res=1
> [ 1.023873] cpuidle: using governor ladder
> [ 1.026734] cpuidle: using governor menu
> [ 1.029477] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
> [ 1.035332] Serial: AMBA PL011 UART driver
> [ 1.039319] Machine: SolidRun LX2160A Clearfog CX
> [ 1.042751] SoC family: QorIQ LX2160A
> [ 1.045135] SoC ID: svr:0x87361010, Revision: 1.0
> [ 1.049775] 21c0000.serial: ttyAMA0 at MMIO 0x21c0000 (irq = 17, base_baud = 0) is a SBSA
> [ 1.056765] printk: console [ttyAMA0] enabled
> [ 1.062890] printk: bootconsole [pl11] disabled
> [ 1.069745] 21d0000.serial: ttyAMA1 at MMIO 0x21d0000 (irq = 18, base_baud = 0) is a SBSA
> [ 1.083284] fsl_mc_bus 80c000000.fsl-mc: MC firmware version: 10.18.0
> [ 1.091046] fsl_mc_dprc dprc.1: DMA mask not set
> [ 1.104098] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
> [ 1.109500] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
> [ 1.114906] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
> [ 1.120298] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
> [ 1.127238] cryptd: max_cpu_qlen set to 1000
> [ 1.132187] iommu: Default domain type: Translated (set via kernel command line)
> [ 1.138411] vgaarb: loaded
> [ 1.140045] SCSI subsystem initialized
> [ 1.142660] libata version 3.00 loaded.
> [ 1.142830] usbcore: registered new interface driver usbfs
> [ 1.147050] usbcore: registered new interface driver hub
> [ 1.151152] usbcore: registered new device driver usb
> [ 1.155269] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported
> [ 1.161373] i2c i2c-0: IMX I2C adapter registered
> [ 1.164914] imx-i2c 2020000.i2c: can't get pinctrl, bus recovery not supported
> [ 1.170923] i2c i2c-1: IMX I2C adapter registered
> [ 1.174438] imx-i2c 2040000.i2c: can't get pinctrl, bus recovery not supported
> [ 1.180489] i2c i2c-2: IMX I2C adapter registered
> [ 1.184034] pps_core: LinuxPPS API ver. 1 registered
> [ 1.187711] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
> [ 1.195563] PTP clock support registered
> [ 1.198926] clocksource: Switched to clocksource arch_sys_counter
> [ 1.409271] VFS: Disk quotas dquot_6.6.0
> [ 1.411929] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
> [ 1.423147] NET: Registered protocol family 2
> [ 1.426524] tcp_listen_portaddr_hash hash table entries: 4096 (order: 6, 294912 bytes, linear)
> [ 1.434212] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear)
> [ 1.441038] TCP bind hash table entries: 65536 (order: 10, 4194304 bytes, linear)
> [ 1.452946] TCP: Hash tables configured (established 65536 bind 65536)
> [ 1.458362] UDP hash table entries: 4096 (order: 7, 655360 bytes, linear)
> [ 1.464637] UDP-Lite hash table entries: 4096 (order: 7, 655360 bytes, linear)
> [ 1.471476] NET: Registered protocol family 1
> [ 1.474948] RPC: Registered named UNIX socket transport module.
> [ 1.479561] RPC: Registered udp transport module.
> [ 1.482958] RPC: Registered tcp transport module.
> [ 1.486348] RPC: Registered tcp NFSv4.1 backchannel transport module.
> [ 1.491485] PCI: CLS 0 bytes, default 64
> [ 1.495248] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available
> [ 1.502280] kvm: Limiting the IPA size due to kernel Virtual Address limit
> [ 1.507851] kvm [1]: IPA Size Limit: 43bits
> [ 1.511572] kvm [1]: vgic-v2@c0e0000
> [ 1.513851] kvm [1]: GIC system register CPU interface enabled
> [ 1.518687] kvm [1]: vgic interrupt IRQ1
> [ 1.521608] kvm [1]: Hyp mode initialized successfully
> [ 1.535818] workingset: timestamp_bits=46 max_order=21 bucket_order=0
> [ 1.549175] NFS: Registering the id_resolver key type
> [ 1.552967] Key type id_resolver registered
> [ 1.555844] Key type id_legacy registered
> [ 1.558661] fuse: init (API version 7.31)
> [ 1.561605] 9p: Installing v9fs 9p2000 file system support
> [ 1.566505] io scheduler mq-deadline registered
> [ 1.569734] io scheduler kyber registered
> [ 1.573894] layerscape-pcie-gen4 3600000.pcie: host bridge /soc/pcie@3600000 ranges:
> [ 1.580351] layerscape-pcie-gen4 3600000.pcie: MEM 0x9040000000..0x907fffffff -> 0x0040000000
> [ 1.588204] layerscape-pcie-gen4 3600000.pcie: PCI host bridge to bus 0000:00
> [ 1.594036] pci_bus 0000:00: root bus resource [bus 00-ff]
> [ 1.598216] pci_bus 0000:00: root bus resource [mem 0x9040000000-0x907fffffff] (bus address [0x40000000-0x7fffffff])
> [ 1.607459] pci 0000:00:00.0: [1957:8d90] type 01 class 0x060400
> [ 1.612198] pci 0000:00:00.0: enabling Extended Tags
> [ 1.615912] pci 0000:00:00.0: supports D1 D2
> [ 1.618869] pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot D3cold
> [ 1.624897] pci 0000:01:00.0: [1cc1:8201] type 00 class 0x010802
> [ 1.629666] pci 0000:01:00.0: reg 0x10: [mem 0x9040000000-0x9040003fff 64bit]
> [ 1.646977] pci 0000:00:00.0: up support 3 enabled 0
> [ 1.650628] pci 0000:00:00.0: dn support 2 enabled 0
> [ 1.654743] pci 0000:00:00.0: BAR 8: assigned [mem 0x9040000000-0x90400fffff]
> [ 1.660577] pci 0000:01:00.0: BAR 0: assigned [mem 0x9040000000-0x9040003fff 64bit]
> [ 1.666945] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
> [ 1.670859] pci 0000:00:00.0: bridge window [mem 0x9040000000-0x90400fffff]
> [ 1.676698] pci 0000:00:00.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256
> [ 1.683858] pci 0000:01:00.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256
> [ 1.691047] pcieport 0000:00:00.0: PCIe capabilities: 0x13
> [ 1.695230] pcieport 0000:00:00.0: init_service_irqs: -19
> [ 1.699429] layerscape-pcie-gen4 3800000.pcie: host bridge /soc/pcie@3800000 ranges:
> [ 1.705877] layerscape-pcie-gen4 3800000.pcie: MEM 0xa040000000..0xa07fffffff -> 0x0040000000
> [ 1.713713] layerscape-pcie-gen4 3800000.pcie: PCI host bridge to bus 0001:00
> [ 1.719544] pci_bus 0001:00: root bus resource [bus 00-ff]
> [ 1.723724] pci_bus 0001:00: root bus resource [mem 0xa040000000-0xa07fffffff] (bus address [0x40000000-0x7fffffff])
> [ 1.732950] pci 0001:00:00.0: [1957:8d90] type 01 class 0x060400
> [ 1.737694] pci 0001:00:00.0: enabling Extended Tags
> [ 1.741407] pci 0001:00:00.0: supports D1 D2
> [ 1.744371] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot D3cold
> [ 1.750511] pci 0001:01:00.0: [15b3:6750] type 00 class 0x020000
> [ 1.755600] pci 0001:01:00.0: reg 0x10: [mem 0xa040000000-0xa0400fffff 64bit]
> [ 1.761632] pci 0001:01:00.0: reg 0x18: [mem 0xa040800000-0xa040ffffff 64bit pref]
> [ 1.768286] pci 0001:01:00.0: reg 0x30: [mem 0xa041000000-0xa0410fffff pref]
> [ 1.787013] pci 0001:00:00.0: up support 3 enabled 0
> [ 1.790665] pci 0001:00:00.0: dn support 1 enabled 0
> [ 1.794787] pci 0001:00:00.0: BAR 9: assigned [mem 0xa040000000-0xa0407fffff 64bit pref]
> [ 1.801572] pci 0001:00:00.0: BAR 8: assigned [mem 0xa040800000-0xa0409fffff]
> [ 1.807404] pci 0001:01:00.0: BAR 2: assigned [mem 0xa040000000-0xa0407fffff 64bit pref]
> [ 1.814316] pci 0001:01:00.0: BAR 0: assigned [mem 0xa040800000-0xa0408fffff 64bit]
> [ 1.820793] pci 0001:01:00.0: BAR 6: assigned [mem 0xa040900000-0xa0409fffff pref]
> [ 1.827056] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
> [ 1.830977] pci 0001:00:00.0: bridge window [mem 0xa040800000-0xa0409fffff]
> [ 1.836806] pci 0001:00:00.0: bridge window [mem 0xa040000000-0xa0407fffff 64bit pref]
> [ 1.843601] pci 0001:00:00.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256
> [ 1.850903] pci 0001:01:00.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256
> [ 1.858079] pcieport 0001:00:00.0: PCIe capabilities: 0x13
> [ 1.862260] pcieport 0001:00:00.0: init_service_irqs: -19
> [ 1.867322] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
> [ 1.874084] arm-smmu 5000000.iommu: probing hardware configuration...
> [ 1.879225] arm-smmu 5000000.iommu: SMMUv2 with:
> [ 1.882529] arm-smmu 5000000.iommu: stage 1 translation
> [ 1.886534] arm-smmu 5000000.iommu: stage 2 translation
> [ 1.890539] arm-smmu 5000000.iommu: nested translation
> [ 1.894457] arm-smmu 5000000.iommu: coherent table walk
> [ 1.898461] arm-smmu 5000000.iommu: (IDR0.CTTW overridden by FW configuration)
> [ 1.904464] arm-smmu 5000000.iommu: stream matching with 128 register groups
> [ 1.910294] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only)
> [ 1.915519] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000
> [ 1.920653] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA
> [ 1.925786] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA
> [ 1.946137] loop: module loaded
> [ 1.948871] nvme nvme0: pci function 0000:01:00.0
> [ 1.952710] ahci-qoriq 3200000.sata: 3200000.sata supply ahci not found, using dummy regulator
> [ 1.960072] ahci-qoriq 3200000.sata: 3200000.sata supply phy not found, using dummy regulator
> [ 1.967335] ahci-qoriq 3200000.sata: 3200000.sata supply target not found, using dummy regulator
> [ 1.974957] ahci-qoriq 3200000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode
> [ 1.982613] ahci-qoriq 3200000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst
> [ 1.991486] scsi host0: ahci-qoriq
> [ 1.993859] ata1: SATA max UDMA/133 mmio [mem 0x03200000-0x0320ffff] port 0x100 irq 24
> [ 2.000561] ahci-qoriq 3210000.sata: 3210000.sata supply ahci not found, using dummy regulator
> [ 2.007916] ahci-qoriq 3210000.sata: 3210000.sata supply phy not found, using dummy regulator
> [ 2.015194] ahci-qoriq 3210000.sata: 3210000.sata supply target not found, using dummy regulator
> [ 2.022788] ahci-qoriq 3210000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode
> [ 2.030443] ahci-qoriq 3210000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst
> [ 2.039256] scsi host1: ahci-qoriq
> [ 2.041507] ata2: SATA max UDMA/133 mmio [mem 0x03210000-0x0321ffff] port 0x100 irq 25
> [ 2.048196] ahci-qoriq 3220000.sata: 3220000.sata supply ahci not found, using dummy regulator
> [ 2.055550] ahci-qoriq 3220000.sata: 3220000.sata supply phy not found, using dummy regulator
> [ 2.062811] ahci-qoriq 3220000.sata: 3220000.sata supply target not found, using dummy regulator
> [ 2.070378] ahci-qoriq 3220000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode
> [ 2.078032] ahci-qoriq 3220000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst
> [ 2.084600] nvme nvme0: 15/0/0 default/read/poll queues
> [ 2.086837] scsi host2: ahci-qoriq
> [ 2.092574] ata3: SATA max UDMA/133 mmio [mem 0x03220000-0x0322ffff] port 0x100 irq 26
> [ 2.092925] nvme0n1: p1 p2
> [ 2.099262] ahci-qoriq 3230000.sata: 3230000.sata supply ahci not found, using dummy regulator
> [ 2.108028] ahci-qoriq 3230000.sata: 3230000.sata supply phy not found, using dummy regulator
> [ 2.115290] ahci-qoriq 3230000.sata: 3230000.sata supply target not found, using dummy regulator
> [ 2.122864] ahci-qoriq 3230000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode
> [ 2.130518] ahci-qoriq 3230000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst
> [ 2.139348] scsi host3: ahci-qoriq
> [ 2.141598] ata4: SATA max UDMA/133 mmio [mem 0x03230000-0x0323ffff] port 0x100 irq 27
> [ 2.149539] libphy: Fixed MDIO Bus: probed
> [ 2.152802] libphy: Freescale XGMAC MDIO Bus: probed
> [ 2.156799] Qualcomm Atheros AR8035 8b96000:01: probe: irq=-1
> [ 2.161245] Qualcomm Atheros AR8035 8b96000:01: probe: irq=-1
> [ 2.165963] libphy: Freescale XGMAC MDIO Bus: probed
> [ 2.170081] dwc3 3100000.usb: Failed to get clk 'ref': -2
> [ 2.174468] dwc3 3110000.usb: Failed to get clk 'ref': -2
> [ 2.179050] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
> [ 2.184274] ehci-platform: EHCI generic platform driver
> [ 2.188257] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
> [ 2.193140] ohci-platform: OHCI generic platform driver
> [ 2.197268] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
> [ 2.201470] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
> [ 2.207946] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010
> [ 2.216064] xhci-hcd xhci-hcd.0.auto: irq 22, io mem 0x03100000
> [ 2.221416] hub 1-0:1.0: USB hub found
> [ 2.223894] hub 1-0:1.0: 1 port detected
> [ 2.226762] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
> [ 2.230951] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
> [ 2.237305] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
> [ 2.242572] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
> [ 2.249744] hub 2-0:1.0: USB hub found
> [ 2.252209] hub 2-0:1.0: 1 port detected
> [ 2.255118] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
> [ 2.259309] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
> [ 2.265760] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010
> [ 2.273872] xhci-hcd xhci-hcd.1.auto: irq 23, io mem 0x03110000
> [ 2.279084] hub 3-0:1.0: USB hub found
> [ 2.281538] hub 3-0:1.0: 1 port detected
> [ 2.284380] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
> [ 2.288571] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
> [ 2.294930] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
> [ 2.300190] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
> [ 2.307363] hub 4-0:1.0: USB hub found
> [ 2.309817] hub 4-0:1.0: 1 port detected
> [ 2.312750] usbcore: registered new interface driver usb-storage
> [ 2.317173] ata1: SATA link down (SStatus 0 SControl 300)
> [ 2.317696] mousedev: PS/2 mouse device common for all mice
> [ 2.331955] rtc-pcf2127-i2c 2-0051: registered as rtc0
> [ 2.335876] i2c /dev entries driver
> [ 2.339327] i2c i2c-0: Added multiplexed i2c bus 3
> [ 2.343067] i2c i2c-0: Added multiplexed i2c bus 4
> [ 2.346783] i2c i2c-0: Added multiplexed i2c bus 5
> [ 2.350507] i2c i2c-0: Added multiplexed i2c bus 6
> [ 2.354164] i2c i2c-0: Added multiplexed i2c bus 7
> [ 2.357821] i2c i2c-0: Added multiplexed i2c bus 8
> [ 2.361159] ata2: SATA link down (SStatus 0 SControl 300)
> [ 2.361480] i2c i2c-0: Added multiplexed i2c bus 9
> [ 2.369047] i2c i2c-0: Added multiplexed i2c bus 10
> [ 2.372627] pca954x 0-0077: registered 8 multiplexed busses for I2C mux pca9547
> [ 2.378783] IR NEC protocol handler initialized
> [ 2.382010] IR RC5(x/sz) protocol handler initialized
> [ 2.385755] IR RC6 protocol handler initialized
> [ 2.388977] IR JVC protocol handler initialized
> [ 2.392200] IR Sony protocol handler initialized
> [ 2.395513] IR SANYO protocol handler initialized
> [ 2.398903] IR Sharp protocol handler initialized
> [ 2.402300] IR MCE Keyboard/mouse protocol handler initialized
> [ 2.406827] IR XMP protocol handler initialized
> [ 2.413367] amc6821 4-0018: Error reading configuration register, aborting.
> [ 2.417180] ata3: SATA link down (SStatus 0 SControl 300)
> [ 2.419034] amc6821: probe of 4-0018 failed with error -5
> [ 2.427436] sdhci: Secure Digital Host Controller Interface driver
> [ 2.432314] sdhci: Copyright(c) Pierre Ossman
> [ 2.435384] sdhci-pltfm: SDHCI platform and OF driver helper
> [ 2.461157] ata4: SATA link down (SStatus 0 SControl 300)
> [ 2.465487] mmc0: SDHCI controller on 2140000.esdhc [2140000.esdhc] using ADMA 64-bit
> [ 2.494954] mmc1: SDHCI controller on 2150000.esdhc [2150000.esdhc] using ADMA 64-bit
> [ 2.502071] ledtrig-cpu: registered to indicate activity on CPUs
> [ 2.507175] caam 8000000.crypto: device ID = 0x0a1a020000000000 (Era 10)
> [ 2.508538] mmc0: new high speed SDHC card at address aaaa
> [ 2.512572] caam 8000000.crypto: job rings = 3, qi = 1
> [ 2.521006] mmcblk0: mmc0:aaaa SU04G 3.69 GiB (ro)
> [ 2.525840] caam algorithms registered in /proc/crypto
> [ 2.532365] caam 8000000.crypto: caam pkc algorithms registered in /proc/crypto
> [ 2.539400] caam_jr 8010000.jr: registering rng-caam
> [ 2.543736] usbcore: registered new interface driver usbhid
> [ 2.548007] usbhid: USB HID core driver
> [ 2.551148] NET: Registered protocol family 10
> [ 2.554963] Segment Routing with IPv6
> [ 2.557343] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
> [ 2.562313] NET: Registered protocol family 17
> [ 2.565629] 9pnet: Installing 9P2000 support
> [ 2.568641] Key type dns_resolver registered
> [ 2.571820] registered taskstats version 1
> [ 2.578646] fsl_mc_dprc dprc.1: Adding to iommu group 0
> [ 2.584473] mmc1: new HS400 MMC card at address 0001
> [ 2.592566] mmcblk1: mmc1:0001 DF4064 58.2 GiB
> [ 2.595945] mmcblk1boot0: mmc1:0001 DF4064 partition 1 4.00 MiB
> [ 2.600717] mmcblk1boot1: mmc1:0001 DF4064 partition 2 4.00 MiB
> [ 2.605471] mmcblk1rpmb: mmc1:0001 DF4064 partition 3 4.00 MiB, chardev (246:0)
> [ 2.612749] mmcblk1: p1 p2
> [ 2.622945] usb 3-1: new high-speed USB device number 2 using xhci-hcd
> [ 2.642000] fsl_dpaa2_eth dpni.0: Adding to iommu group 0
> [ 2.646254] fsl_mc_dprc dprc.1: No more resources of type dpmcp left
> [ 2.651688] fsl_mc_allocator dpbp.1: Adding to iommu group 0
> [ 2.656161] fsl_mc_allocator dpbp.0: Adding to iommu group 0
> [ 2.662117] fsl_mc_allocator dpmcp.35: Adding to iommu group 0
> [ 2.667765] fsl_mc_allocator dpmcp.34: Adding to iommu group 0
> [ 2.673422] fsl_mc_allocator dpmcp.33: Adding to iommu group 0
> [ 2.679071] fsl_mc_allocator dpmcp.32: Adding to iommu group 0
> [ 2.684267] hub 3-1:1.0: USB hub found
> [ 2.684727] fsl_mc_allocator dpmcp.31: Adding to iommu group 0
> [ 2.686736] hub 3-1:1.0: 4 ports detected
> [ 2.692343] fsl_mc_allocator dpmcp.30: Adding to iommu group 0
> [ 2.699627] fsl_mc_allocator dpmcp.29: Adding to iommu group 0
> [ 2.705265] fsl_mc_allocator dpmcp.28: Adding to iommu group 0
> [ 2.710952] fsl_mc_allocator dpmcp.27: Adding to iommu group 0
> [ 2.716596] fsl_mc_allocator dpmcp.26: Adding to iommu group 0
> [ 2.722243] fsl_mc_allocator dpmcp.25: Adding to iommu group 0
> [ 2.727897] fsl_mc_allocator dpmcp.24: Adding to iommu group 0
> [ 2.733550] fsl_mc_allocator dpmcp.23: Adding to iommu group 0
> [ 2.739198] fsl_mc_allocator dpmcp.22: Adding to iommu group 0
> [ 2.744853] fsl_mc_allocator dpmcp.21: Adding to iommu group 0
> [ 2.750495] fsl_mc_allocator dpmcp.20: Adding to iommu group 0
> [ 2.756161] fsl_mc_allocator dpmcp.19: Adding to iommu group 0
> [ 2.761803] fsl_mc_allocator dpmcp.18: Adding to iommu group 0
> [ 2.767473] fsl_mc_allocator dpmcp.17: Adding to iommu group 0
> [ 2.773117] fsl_mc_allocator dpmcp.16: Adding to iommu group 0
> [ 2.778768] fsl_mc_allocator dpmcp.15: Adding to iommu group 0
> [ 2.782959] usb 4-1: new SuperSpeed Gen 1 USB device number 2 using xhci-hcd
> [ 2.784414] fsl_mc_allocator dpmcp.14: Adding to iommu group 0
> [ 2.794669] fsl_mc_allocator dpmcp.13: Adding to iommu group 0
> [ 2.800309] fsl_mc_allocator dpmcp.12: Adding to iommu group 0
> [ 2.805969] fsl_mc_allocator dpmcp.11: Adding to iommu group 0
> [ 2.811625] fsl_mc_allocator dpmcp.10: Adding to iommu group 0
> [ 2.817271] fsl_mc_allocator dpmcp.9: Adding to iommu group 0
> [ 2.822845] fsl_mc_allocator dpmcp.8: Adding to iommu group 0
> [ 2.828243] hub 4-1:1.0: USB hub found
> [ 2.828420] fsl_mc_allocator dpmcp.7: Adding to iommu group 0
> [ 2.830710] hub 4-1:1.0: 4 ports detected
> [ 2.836276] fsl_mc_allocator dpmcp.6: Adding to iommu group 0
> [ 2.843415] fsl_mc_allocator dpmcp.5: Adding to iommu group 0
> [ 2.848975] fsl_mc_allocator dpmcp.4: Adding to iommu group 0
> [ 2.851038] random: fast init done
> [ 2.854534] fsl_mc_allocator dpmcp.3: Adding to iommu group 0
> [ 2.861060] fsl_mc_allocator dpmcp.2: Adding to iommu group 0
> [ 2.866622] fsl_mc_allocator dpmcp.1: Adding to iommu group 0
> [ 2.874308] fsl_mc_dpio dpio.15: Adding to iommu group 0
> [ 2.882022] fsl_mc_dpio dpio.15: probed
> [ 2.888261] fsl_mc_dpio dpio.14: Adding to iommu group 0
> [ 2.895912] fsl_mc_dpio dpio.14: probed
> [ 2.902061] fsl_mc_dpio dpio.13: Adding to iommu group 0
> [ 2.909710] fsl_mc_dpio dpio.13: probed
> [ 2.915939] fsl_mc_dpio dpio.12: Adding to iommu group 0
> [ 2.923591] fsl_mc_dpio dpio.12: probed
> [ 2.929752] fsl_mc_dpio dpio.11: Adding to iommu group 0
> [ 2.937396] fsl_mc_dpio dpio.11: probed
> [ 2.943628] fsl_mc_dpio dpio.10: Adding to iommu group 0
> [ 2.951283] fsl_mc_dpio dpio.10: probed
> [ 2.957446] fsl_mc_dpio dpio.9: Adding to iommu group 0
> [ 2.965012] fsl_mc_dpio dpio.9: probed
> [ 2.971167] fsl_mc_dpio dpio.8: Adding to iommu group 0
> [ 2.978776] fsl_mc_dpio dpio.8: probed
> [ 2.984923] fsl_mc_dpio dpio.7: Adding to iommu group 0
> [ 2.992537] fsl_mc_dpio dpio.7: probed
> [ 2.998684] fsl_mc_dpio dpio.6: Adding to iommu group 0
> [ 3.006299] fsl_mc_dpio dpio.6: probed
> [ 3.012440] fsl_mc_dpio dpio.5: Adding to iommu group 0
> [ 3.020064] fsl_mc_dpio dpio.5: probed
> [ 3.026190] fsl_mc_dpio dpio.4: Adding to iommu group 0
> [ 3.033754] fsl_mc_dpio dpio.4: probed
> [ 3.038937] usb 3-1.3: new high-speed USB device number 3 using xhci-hcd
> [ 3.039844] fsl_mc_dpio dpio.3: Adding to iommu group 0
> [ 3.051890] fsl_mc_dpio dpio.3: probed
> [ 3.058009] fsl_mc_dpio dpio.2: Adding to iommu group 0
> [ 3.065609] fsl_mc_dpio dpio.2: probed
> [ 3.071763] fsl_mc_dpio dpio.1: Adding to iommu group 0
> [ 3.079384] fsl_mc_dpio dpio.1: probed
> [ 3.085521] fsl_mc_dpio dpio.0: Adding to iommu group 0
> [ 3.093136] fsl_mc_dpio dpio.0: probed
> [ 3.096201] fsl_mc_allocator dpcon.31: Adding to iommu group 0
> [ 3.100196] hub 3-1.3:1.0: USB hub found
> [ 3.100860] fsl_mc_allocator dpcon.30: Adding to iommu group 0
> [ 3.103374] hub 3-1.3:1.0: 4 ports detected
> [ 3.107983] fsl_mc_allocator dpcon.29: Adding to iommu group 0
> [ 3.115381] fsl_mc_allocator dpcon.28: Adding to iommu group 0
> [ 3.120030] fsl_mc_allocator dpcon.27: Adding to iommu group 0
> [ 3.124682] fsl_mc_allocator dpcon.26: Adding to iommu group 0
> [ 3.129333] fsl_mc_allocator dpcon.25: Adding to iommu group 0
> [ 3.133987] fsl_mc_allocator dpcon.24: Adding to iommu group 0
> [ 3.138642] fsl_mc_allocator dpcon.23: Adding to iommu group 0
> [ 3.143294] fsl_mc_allocator dpcon.22: Adding to iommu group 0
> [ 3.147946] fsl_mc_allocator dpcon.21: Adding to iommu group 0
> [ 3.152597] fsl_mc_allocator dpcon.20: Adding to iommu group 0
> [ 3.157250] fsl_mc_allocator dpcon.19: Adding to iommu group 0
> [ 3.161903] fsl_mc_allocator dpcon.18: Adding to iommu group 0
> [ 3.166559] fsl_mc_allocator dpcon.17: Adding to iommu group 0
> [ 3.171217] fsl_mc_allocator dpcon.16: Adding to iommu group 0
> [ 3.175871] fsl_mc_allocator dpcon.15: Adding to iommu group 0
> [ 3.180533] fsl_mc_allocator dpcon.14: Adding to iommu group 0
> [ 3.185188] fsl_mc_allocator dpcon.13: Adding to iommu group 0
> [ 3.189844] fsl_mc_allocator dpcon.12: Adding to iommu group 0
> [ 3.194499] fsl_mc_allocator dpcon.11: Adding to iommu group 0
> [ 3.199153] fsl_mc_allocator dpcon.10: Adding to iommu group 0
> [ 3.203810] fsl_mc_allocator dpcon.9: Adding to iommu group 0
> [ 3.208385] fsl_mc_allocator dpcon.8: Adding to iommu group 0
> [ 3.212956] fsl_mc_allocator dpcon.7: Adding to iommu group 0
> [ 3.217526] fsl_mc_allocator dpcon.6: Adding to iommu group 0
> [ 3.222096] fsl_mc_allocator dpcon.5: Adding to iommu group 0
> [ 3.226667] fsl_mc_allocator dpcon.4: Adding to iommu group 0
> [ 3.231237] fsl_mc_allocator dpcon.3: Adding to iommu group 0
> [ 3.235812] fsl_mc_allocator dpcon.2: Adding to iommu group 0
> [ 3.240383] fsl_mc_allocator dpcon.1: Adding to iommu group 0
> [ 3.244955] fsl_mc_allocator dpcon.0: Adding to iommu group 0
> [ 3.252565] fsl_mc_dprc dprc.1: DPRC device bound to driver
> [ 3.257032] libphy: SFP I2C Bus: probed
> [ 3.259658] sfp sfp-0: Host maximum power 2.0W
> [ 3.262929] sfp sfp-0: No tx_disable pin: SFP modules will always be emitting.
> [ 3.269061] libphy: SFP I2C Bus: probed
> [ 3.271642] sfp sfp-1: Host maximum power 2.0W
> [ 3.274884] sfp sfp-1: No tx_disable pin: SFP modules will always be emitting.
> [ 3.280979] libphy: SFP I2C Bus: probed
> [ 3.283559] sfp sfp-2: Host maximum power 2.0W
> [ 3.286819] sfp sfp-2: No tx_disable pin: SFP modules will always be emitting.
> [ 3.292948] libphy: SFP I2C Bus: probed
> [ 3.295529] sfp sfp-3: Host maximum power 2.0W
> [ 3.298768] sfp sfp-3: No tx_disable pin: SFP modules will always be emitting.
> [ 3.456609] fsl_dpaa2_eth dpni.0 (unnamed net_device) (uninitialized): PHY [8b96000:01] driver [Qualcomm Atheros AR8035] (irq=POLL)
> [ 3.467153] fsl_dpaa2_eth dpni.0 (unnamed net_device) (uninitialized): phy: setting supported 000,00000200,000062ea advertising 000,00000200,000062ea
> [ 3.468341] fsl_dpaa2_eth dpni.0: Probed interface eth0
> [ 3.472672] input: gpio-keys as /devices/platform/gpio-keys/input/input0
> [ 3.479780] rtc-pcf2127-i2c 2-0051: setting system clock to 2020-02-28T09:56:18 UTC (1582883778)
> [ 3.490224] EXT4-fs (nvme0n1p2): mounted filesystem with ordered data mode. Opts: (null)
> [ 3.497082] VFS: Mounted root (ext4 filesystem) readonly on device 259:2.
> [ 3.503193] devtmpfs: mounted
> [ 3.505079] Freeing unused kernel memory: 960K
> [ 3.534993] Run /sbin/init as init process
>
> When asking for more network interfaces, more "Adding to iommu group"
> messages get spat out:
>
> [ 446.040825] fsl_dpaa2_eth dpni.1: Adding to iommu group 0
> [ 446.201254] libphy: Freescale XGMAC MDIO Bus: probed
> [ 446.206552] fsl_dpaa2_eth dpni.1: Probed interface eth1
> [ 446.210715] fsl_mc_allocator dpbp.2: Adding to iommu group 0
> [ 446.216838] fsl_mc_allocator dpmcp.36: Adding to iommu group 0
> [ 446.224808] fsl_mc_allocator dpcon.47: Adding to iommu group 0
> [ 446.229935] fsl_mc_allocator dpcon.46: Adding to iommu group 0
> [ 446.234685] fsl_mc_allocator dpcon.45: Adding to iommu group 0
> [ 446.239431] fsl_mc_allocator dpcon.44: Adding to iommu group 0
> [ 446.244179] fsl_mc_allocator dpcon.43: Adding to iommu group 0
> [ 446.251725] fsl_mc_allocator dpcon.42: Adding to iommu group 0
> [ 446.258952] fsl_mc_allocator dpcon.41: Adding to iommu group 0
> [ 446.263666] fsl_mc_allocator dpcon.40: Adding to iommu group 0
> [ 446.268377] fsl_mc_allocator dpcon.39: Adding to iommu group 0
> [ 446.273086] fsl_mc_allocator dpcon.38: Adding to iommu group 0
> [ 446.277814] fsl_mc_allocator dpcon.37: Adding to iommu group 0
> [ 446.282517] fsl_mc_allocator dpcon.36: Adding to iommu group 0
> [ 446.287228] fsl_mc_allocator dpcon.35: Adding to iommu group 0
> [ 446.291935] fsl_mc_allocator dpcon.34: Adding to iommu group 0
> [ 446.296641] fsl_mc_allocator dpcon.33: Adding to iommu group 0
> [ 446.301354] fsl_mc_allocator dpcon.32: Adding to iommu group 0
> [ 446.893939] fsl_dpaa2_eth dpni.2: Adding to iommu group 0
> [ 447.052868] libphy: Freescale XGMAC MDIO Bus: probed
> [ 447.058223] fsl_dpaa2_eth dpni.2: Probed interface eth2
> [ 447.062425] fsl_mc_allocator dpbp.3: Adding to iommu group 0
> [ 447.068813] fsl_mc_allocator dpmcp.37: Adding to iommu group 0
> [ 447.074280] fsl_mc_allocator dpcon.63: Adding to iommu group 0
> [ 447.078995] fsl_mc_allocator dpcon.62: Adding to iommu group 0
> [ 447.088690] fsl_mc_allocator dpcon.61: Adding to iommu group 0
> [ 447.093639] fsl_mc_allocator dpcon.60: Adding to iommu group 0
> [ 447.098369] fsl_mc_allocator dpcon.59: Adding to iommu group 0
> [ 447.103089] fsl_mc_allocator dpcon.58: Adding to iommu group 0
> [ 447.107811] fsl_mc_allocator dpcon.57: Adding to iommu group 0
> [ 447.112525] fsl_mc_allocator dpcon.56: Adding to iommu group 0
> [ 447.117244] fsl_mc_allocator dpcon.55: Adding to iommu group 0
> [ 447.121962] fsl_mc_allocator dpcon.54: Adding to iommu group 0
> [ 447.126680] fsl_mc_allocator dpcon.53: Adding to iommu group 0
> [ 447.131392] fsl_mc_allocator dpcon.52: Adding to iommu group 0
> [ 447.136107] fsl_mc_allocator dpcon.51: Adding to iommu group 0
> [ 447.140820] fsl_mc_allocator dpcon.50: Adding to iommu group 0
> [ 447.145535] fsl_mc_allocator dpcon.49: Adding to iommu group 0
> [ 447.150249] fsl_mc_allocator dpcon.48: Adding to iommu group 0
> [ 447.710694] fsl_dpaa2_eth dpni.3: Adding to iommu group 0
> [ 447.888120] libphy: Freescale XGMAC MDIO Bus: probed
> [ 447.893479] fsl_dpaa2_eth dpni.3: Probed interface eth3
> [ 447.897740] fsl_mc_allocator dpbp.4: Adding to iommu group 0
> [ 447.904488] fsl_mc_allocator dpmcp.38: Adding to iommu group 0
> [ 447.909994] fsl_mc_allocator dpcon.79: Adding to iommu group 0
> [ 447.914717] fsl_mc_allocator dpcon.78: Adding to iommu group 0
> [ 447.919852] fsl_mc_allocator dpcon.77: Adding to iommu group 0
> [ 447.924720] fsl_mc_allocator dpcon.76: Adding to iommu group 0
> [ 447.931979] fsl_mc_allocator dpcon.75: Adding to iommu group 0
> [ 447.939172] fsl_mc_allocator dpcon.74: Adding to iommu group 0
> [ 447.943886] fsl_mc_allocator dpcon.73: Adding to iommu group 0
> [ 447.948604] fsl_mc_allocator dpcon.72: Adding to iommu group 0
> [ 447.953319] fsl_mc_allocator dpcon.71: Adding to iommu group 0
> [ 447.958035] fsl_mc_allocator dpcon.70: Adding to iommu group 0
> [ 447.965445] fsl_mc_allocator dpcon.69: Adding to iommu group 0
> [ 447.972653] fsl_mc_allocator dpcon.68: Adding to iommu group 0
> [ 447.977376] fsl_mc_allocator dpcon.67: Adding to iommu group 0
> [ 447.982097] fsl_mc_allocator dpcon.66: Adding to iommu group 0
> [ 447.986816] fsl_mc_allocator dpcon.65: Adding to iommu group 0
> [ 447.991532] fsl_mc_allocator dpcon.64: Adding to iommu group 0
> [ 448.737198] fsl_dpaa2_eth dpni.4: Adding to iommu group 0
> [ 448.894480] libphy: Freescale XGMAC MDIO Bus: probed
> [ 448.899785] fsl_dpaa2_eth dpni.4: Probed interface eth4
> [ 448.904077] fsl_mc_allocator dpbp.5: Adding to iommu group 0
> [ 448.909817] fsl_mc_allocator dpmcp.39: Adding to iommu group 0
> [ 448.915340] fsl_mc_allocator dpcon.95: Adding to iommu group 0
> [ 448.920068] fsl_mc_allocator dpcon.94: Adding to iommu group 0
> [ 448.924789] fsl_mc_allocator dpcon.93: Adding to iommu group 0
> [ 448.929689] fsl_mc_allocator dpcon.92: Adding to iommu group 0
> [ 448.934436] fsl_mc_allocator dpcon.91: Adding to iommu group 0
> [ 448.939159] fsl_mc_allocator dpcon.90: Adding to iommu group 0
> [ 448.943882] fsl_mc_allocator dpcon.89: Adding to iommu group 0
> [ 448.948607] fsl_mc_allocator dpcon.88: Adding to iommu group 0
> [ 448.953327] fsl_mc_allocator dpcon.87: Adding to iommu group 0
> [ 448.958050] fsl_mc_allocator dpcon.86: Adding to iommu group 0
> [ 448.962771] fsl_mc_allocator dpcon.85: Adding to iommu group 0
> [ 448.967499] fsl_mc_allocator dpcon.84: Adding to iommu group 0
> [ 448.972219] fsl_mc_allocator dpcon.83: Adding to iommu group 0
> [ 448.976941] fsl_mc_allocator dpcon.82: Adding to iommu group 0
> [ 448.981669] fsl_mc_allocator dpcon.81: Adding to iommu group 0
> [ 448.986391] fsl_mc_allocator dpcon.80: Adding to iommu group 0
>
> # dmesg |grep 'Adding to iommu' | wc -l
> 164
> # dmesg |grep -v 'Adding to iommu' | wc -l
> 551
>
> So, 23% of the kernel messages on this platform are "Adding to iommu",
> which is excessive.
Indeed, however I would note that on most platforms bringing up a
network interface involves hot-adding 0 devices, so hot-adding 19
devices as full-blown DMA masters is arguably the root of "excessive"
already. Per the concern I initially raised, each of those messages
represents a whole bunch of internal allocation and bookkeeping going
on, which if it isn't necessary would be far better avoided altogether,
than simply done more quietly.
Laurentiu, I guess at the moment the nature of the of_dma_configure()
integration means we end up treating all DPAA2 objects identically, but
do you think we have scope to be a bit cleverer in that regard?
Presumably not every type of object that shows up on the fsl_mc bus is
really an independent DMA master, so if we could skip doing the full
DMA/IOMMU/MSI setup for the ones that don't need it, it would work out
nicer all round. In fact your .dma_configure proposal (which I'll try to
take a proper look at next week) couldn't have come at a better time for
that argument :)
Robin.
_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu
^ permalink raw reply [flat|nested] 24+ messages in thread
* RE: [PATCH] iommu: silence iommu group prints
2020-02-28 18:32 ` Robin Murphy
@ 2020-03-02 11:48 ` Laurentiu Tudor
2020-03-03 14:18 ` Laurentiu Tudor
1 sibling, 0 replies; 24+ messages in thread
From: Laurentiu Tudor @ 2020-03-02 11:48 UTC (permalink / raw)
To: Robin Murphy, Russell King - ARM Linux admin
Cc: Diana Madalina Craciun, iommu, Ioana Ciornei
Hi Robin,
> -----Original Message-----
> From: Robin Murphy <robin.murphy@arm.com>
> Sent: Friday, February 28, 2020 8:32 PM
>
> [ +Laurentiu ]
>
> Hi Russell,
>
> Thanks for sharing a log, now I properly understand what's up... further
> comments at the end (for context).
>
> On 28/02/2020 10:06 am, Russell King - ARM Linux admin wrote:
> > On Fri, Feb 28, 2020 at 09:33:40AM +0000, John Garry wrote:
> >> On 28/02/2020 02:16, Lu Baolu wrote:
> >>> Hi,
> >>>
> >>> On 2020/2/27 19:57, Russell King wrote:
> >>>> On the LX2160A, there are lots (about 160) of IOMMU messages produced
> >>>> during boot; this is excessive. Reduce the severity of these
> messages
> >>>> to debug level.
> >>>>
> >>>> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
> >>>> ---
> >>>> drivers/iommu/iommu.c | 4 ++--
> >>>> 1 file changed, 2 insertions(+), 2 deletions(-)
> >>>>
> >>>> diff --git a/drivers/iommu/iommu.c b/drivers/iommu/iommu.c
> >>>> index 3ead597e1c57..304281ec623b 100644
> >>>> --- a/drivers/iommu/iommu.c
> >>>> +++ b/drivers/iommu/iommu.c
> >>>> @@ -741,7 +741,7 @@ int iommu_group_add_device(struct iommu_group
> >>>> *group, struct device *dev)
> >>>> trace_add_device_to_group(group->id, dev);
> >>>> - dev_info(dev, "Adding to iommu group %d\n", group->id);
> >>>> + dev_dbg(dev, "Adding to iommu group %d\n", group->id);
> >>>
> >>> I'm not strongly against this. But to me this message seems to be a
> good
> >>> indicator that a device was probed successfully by the iommu subsystem.
> >>> Keeping it in the default kernel message always helps to the kernel
> >>> debugging.
> >>>
> >>
> >> I would tend to agree.
> >
[snip]
> >
> > # dmesg |grep 'Adding to iommu' | wc -l
> > 164
> > # dmesg |grep -v 'Adding to iommu' | wc -l
> > 551
> >
> > So, 23% of the kernel messages on this platform are "Adding to iommu",
> > which is excessive.
>
> Indeed, however I would note that on most platforms bringing up a
> network interface involves hot-adding 0 devices, so hot-adding 19
> devices as full-blown DMA masters is arguably the root of "excessive"
> already. Per the concern I initially raised, each of those messages
> represents a whole bunch of internal allocation and bookkeeping going
> on, which if it isn't necessary would be far better avoided altogether,
> than simply done more quietly.
>
> Laurentiu, I guess at the moment the nature of the of_dma_configure()
> integration means we end up treating all DPAA2 objects identically, but
> do you think we have scope to be a bit cleverer in that regard?
> Presumably not every type of object that shows up on the fsl_mc bus is
> really an independent DMA master, so if we could skip doing the full
> DMA/IOMMU/MSI setup for the ones that don't need it, it would work out
> nicer all round. In fact your .dma_configure proposal (which I'll try to
> take a proper look at next week) couldn't have come at a better time for
> that argument :)
Thanks! That's a very good point - I'll check on which devices we actually use
dma apis and filter the rest out. Will keep in mind for the next spin of the patches.
---
Best Regards, Laurentiu
_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH] iommu: silence iommu group prints
2020-02-27 11:57 [PATCH] iommu: silence iommu group prints Russell King
2020-02-27 13:44 ` Robin Murphy
2020-02-28 2:16 ` Lu Baolu
@ 2020-03-02 15:44 ` Joerg Roedel
2 siblings, 0 replies; 24+ messages in thread
From: Joerg Roedel @ 2020-03-02 15:44 UTC (permalink / raw)
To: Russell King; +Cc: iommu
On Thu, Feb 27, 2020 at 11:57:52AM +0000, Russell King wrote:
> On the LX2160A, there are lots (about 160) of IOMMU messages produced
> during boot; this is excessive. Reduce the severity of these messages
> to debug level.
No, these messages are a very useful tool when it comes to debugging
IOMMU issues on other platforms, and the user only has to provide dmesg
output. When your system has 160 devices, so be it.
Regards,
Joerg
_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH] iommu: silence iommu group prints
2020-02-28 18:32 ` Robin Murphy
2020-03-02 11:48 ` Laurentiu Tudor
@ 2020-03-03 14:18 ` Laurentiu Tudor
2020-03-03 15:49 ` Russell King - ARM Linux admin
1 sibling, 1 reply; 24+ messages in thread
From: Laurentiu Tudor @ 2020-03-03 14:18 UTC (permalink / raw)
To: Robin Murphy, Russell King - ARM Linux admin
Cc: Diana Madalina Craciun, iommu, Ioana Ciornei
On 28.02.2020 20:32, Robin Murphy wrote:
> [ +Laurentiu ]
>
> Hi Russell,
>
> Thanks for sharing a log, now I properly understand what's up... further
> comments at the end (for context).
>
> On 28/02/2020 10:06 am, Russell King - ARM Linux admin wrote:
>> On Fri, Feb 28, 2020 at 09:33:40AM +0000, John Garry wrote:
>>> On 28/02/2020 02:16, Lu Baolu wrote:
>>>> Hi,
>>>>
>>>> On 2020/2/27 19:57, Russell King wrote:
>>>>> On the LX2160A, there are lots (about 160) of IOMMU messages produced
>>>>> during boot; this is excessive. Reduce the severity of these messages
>>>>> to debug level.
>>>>>
>>>>> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
>>>>> ---
>>>>> drivers/iommu/iommu.c | 4 ++--
>>>>> 1 file changed, 2 insertions(+), 2 deletions(-)
>>>>>
>>>>> diff --git a/drivers/iommu/iommu.c b/drivers/iommu/iommu.c
>>>>> index 3ead597e1c57..304281ec623b 100644
>>>>> --- a/drivers/iommu/iommu.c
>>>>> +++ b/drivers/iommu/iommu.c
>>>>> @@ -741,7 +741,7 @@ int iommu_group_add_device(struct iommu_group
>>>>> *group, struct device *dev)
>>>>> trace_add_device_to_group(group->id, dev);
>>>>> - dev_info(dev, "Adding to iommu group %d\n", group->id);
>>>>> + dev_dbg(dev, "Adding to iommu group %d\n", group->id);
>>>>
>>>> I'm not strongly against this. But to me this message seems to be a
>>>> good
>>>> indicator that a device was probed successfully by the iommu subsystem.
>>>> Keeping it in the default kernel message always helps to the kernel
>>>> debugging.
>>>>
>>>
>>> I would tend to agree.
>>
>> Here's the boot messages. Notice how many of these "Adding to iommu
>> group" messages there are:
>>
>> [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083]
>> [ 0.000000] Linux version 5.5.0+ (rmk@rmk-PC) (gcc version 4.9.2
>> (GCC)) #655 SMP PREEMPT Fri Feb 28 09:54:47 GMT 2020
>> [ 0.000000] Machine model: SolidRun LX2160A Clearfog CX
>> [ 0.000000] earlycon: pl11 at MMIO32 0x00000000021c0000 (options '')
>> [ 0.000000] printk: bootconsole [pl11] enabled
>> [ 0.000000] efi: Getting EFI parameters from FDT:
>> [ 0.000000] efi: UEFI not found.
>> [ 0.000000] cma: Reserved 32 MiB at 0x00000000f9c00000
>> [ 0.000000] On node 0 totalpages: 1555968
>> [ 0.000000] DMA zone: 4096 pages used for memmap
>> [ 0.000000] DMA zone: 0 pages reserved
>> [ 0.000000] DMA zone: 262144 pages, LIFO batch:63
>> [ 0.000000] DMA32 zone: 3832 pages used for memmap
>> [ 0.000000] DMA32 zone: 245248 pages, LIFO batch:63
>> [ 0.000000] Normal zone: 16384 pages used for memmap
>> [ 0.000000] Normal zone: 1048576 pages, LIFO batch:63
>> [ 0.000000] psci: probing for conduit method from DT.
>> [ 0.000000] psci: PSCIv1.1 detected in firmware.
>> [ 0.000000] psci: Using standard PSCI v0.2 function IDs
>> [ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
>> [ 0.000000] psci: SMC Calling Convention v1.1
>> [ 0.000000] percpu: Embedded 31 pages/cpu s88968 r8192 d29816 u126976
>> [ 0.000000] pcpu-alloc: s88968 r8192 d29816 u126976 alloc=31*4096
>> [ 0.000000] pcpu-alloc: [0] 00 [0] 01 [0] 02 [0] 03 [0] 04 [0] 05
>> [0] 06 [0] 07
>> [ 0.000000] pcpu-alloc: [0] 08 [0] 09 [0] 10 [0] 11 [0] 12 [0] 13
>> [0] 14 [0] 15
>> [ 0.000000] Detected PIPT I-cache on CPU0
>> [ 0.000000] CPU features: detected: GIC system register CPU interface
>> [ 0.000000] CPU features: detected: EL2 vector hardening
>> [ 0.000000] Speculative Store Bypass Disable mitigation not required
>> [ 0.000000] CPU features: detected: ARM erratum 1319367
>> [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages:
>> 1531656
>> [ 0.000000] Kernel command line: console=ttyAMA0,115200
>> root=PARTUUID=c7837e2f-02 rootwait earlycon=pl011,mmio32,0x21c0000
>> ramdisk_size=0 pci=pcie_bus_perf arm_smmu.disable_bypass=0
>> iommu.passthrough=0
>> [ 0.000000] Dentry cache hash table entries: 1048576 (order: 11,
>> 8388608 bytes, linear)
>> [ 0.000000] Inode-cache hash table entries: 524288 (order: 10,
>> 4194304 bytes, linear)
>> [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
>> [ 0.000000] software IO TLB: mapped [mem 0xbbfff000-0xbffff000] (64MB)
>> [ 0.000000] Memory: 5991500K/6223872K available (10172K kernel
>> code, 1376K rwdata, 3888K rodata, 960K init, 4326K bss, 199604K
>> reserved, 32768K cma-reserved)
>> [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=16,
>> Nodes=1
>> [ 0.000000] rcu: Preemptible hierarchical RCU implementation.
>> [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=64 to
>> nr_cpu_ids=16.
>> [ 0.000000] Tasks RCU enabled.
>> [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay
>> is 25 jiffies.
>> [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16,
>> nr_cpu_ids=16
>> [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
>> [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
>> [ 0.000000] GICv3: 256 SPIs implemented
>> [ 0.000000] GICv3: 0 Extended SPIs implemented
>> [ 0.000000] GICv3: Distributor has no Range Selector support
>> [ 0.000000] GICv3: 16 PPIs implemented
>> [ 0.000000] GICv3: no VLPI support, no direct LPI support
>> [ 0.000000] GICv3: CPU0: found redistributor 0 region
>> 0:0x0000000006200000
>> [ 0.000000] ITS [mem 0x06020000-0x0603ffff]
>> [ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices
>> @2178d00000 (flat, esz 8, psz 64K, shr 0)
>> [ 0.000000] ITS: using cache flushing for cmd queue
>> [ 0.000000] GICv3: using LPI property table @0x0000002178cd0000
>> [ 0.000000] GIC: using cache flushing for LPI property table
>> [ 0.000000] GICv3: CPU0: using allocated LPI pending table
>> @0x0000002178ce0000
>> [ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys).
>> [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff
>> max_cycles: 0x5c409fb33, max_idle_ns: 440795203156 ns
>> [ 0.000002] sched_clock: 56 bits at 25MHz, resolution 39ns, wraps
>> every 4398046511103ns
>> [ 0.006921] Console: colour dummy device 80x25
>> [ 0.010093] Lock dependency validator: Copyright (c) 2006 Red Hat,
>> Inc., Ingo Molnar
>> [ 0.016605] ... MAX_LOCKDEP_SUBCLASSES: 8
>> [ 0.019421] ... MAX_LOCK_DEPTH: 48
>> [ 0.022329] ... MAX_LOCKDEP_KEYS: 8192
>> [ 0.025408] ... CLASSHASH_SIZE: 4096
>> [ 0.028491] ... MAX_LOCKDEP_ENTRIES: 32768
>> [ 0.031659] ... MAX_LOCKDEP_CHAINS: 65536
>> [ 0.034830] ... CHAINHASH_SIZE: 32768
>> [ 0.037997] memory used by lock dependency info: 3509 kB
>> [ 0.042135] per task-struct memory footprint: 1920 bytes
>> [ 0.046292] Calibrating delay loop (skipped), value calculated
>> using timer frequency.. 50.00 BogoMIPS (lpj=100000)
>> [ 0.055443] pid_max: default: 32768 minimum: 301
>> [ 0.058844] LSM: Security Framework initializing
>> [ 0.062241] Mount-cache hash table entries: 16384 (order: 5, 131072
>> bytes, linear)
>> [ 0.068602] Mountpoint-cache hash table entries: 16384 (order: 5,
>> 131072 bytes, linear)
>> [ 0.099452] ASID allocator initialised with 32768 entries
>> [ 0.111615] rcu: Hierarchical SRCU implementation.
>> [ 0.119672] Platform MSI: gic-its@6020000 domain created
>> [ 0.123765] PCI/MSI: /interrupt-controller@6000000/gic-its@6020000
>> domain created
>> [ 0.130045] fsl-mc MSI:
>> /interrupt-controller@6000000/gic-its@6020000 domain created
>> [ 0.136572] EFI services will not be available.
>> [ 0.148587] smp: Bringing up secondary CPUs ...
>> [ 0.180732] Detected PIPT I-cache on CPU1
>> [ 0.180749] GICv3: CPU1: found redistributor 1 region
>> 0:0x0000000006220000
>> [ 0.180761] GICv3: CPU1: using allocated LPI pending table
>> @0x0000002178cf0000
>> [ 0.180781] CPU1: Booted secondary processor 0x0000000001 [0x410fd083]
>> [ 0.212781] Detected PIPT I-cache on CPU2
>> [ 0.212797] GICv3: CPU2: found redistributor 100 region
>> 0:0x0000000006240000
>> [ 0.212810] GICv3: CPU2: using allocated LPI pending table
>> @0x0000002178d80000
>> [ 0.212830] CPU2: Booted secondary processor 0x0000000100 [0x410fd083]
>> [ 0.244832] Detected PIPT I-cache on CPU3
>> [ 0.244844] GICv3: CPU3: found redistributor 101 region
>> 0:0x0000000006260000
>> [ 0.244855] GICv3: CPU3: using allocated LPI pending table
>> @0x0000002178d90000
>> [ 0.244871] CPU3: Booted secondary processor 0x0000000101 [0x410fd083]
>> [ 0.276894] Detected PIPT I-cache on CPU4
>> [ 0.276910] GICv3: CPU4: found redistributor 200 region
>> 0:0x0000000006280000
>> [ 0.276922] GICv3: CPU4: using allocated LPI pending table
>> @0x0000002178da0000
>> [ 0.276941] CPU4: Booted secondary processor 0x0000000200 [0x410fd083]
>> [ 0.308953] Detected PIPT I-cache on CPU5
>> [ 0.308966] GICv3: CPU5: found redistributor 201 region
>> 0:0x00000000062a0000
>> [ 0.308978] GICv3: CPU5: using allocated LPI pending table
>> @0x0000002178db0000
>> [ 0.308994] CPU5: Booted secondary processor 0x0000000201 [0x410fd083]
>> [ 0.341009] Detected PIPT I-cache on CPU6
>> [ 0.341027] GICv3: CPU6: found redistributor 300 region
>> 0:0x00000000062c0000
>> [ 0.341039] GICv3: CPU6: using allocated LPI pending table
>> @0x0000002178dc0000
>> [ 0.341058] CPU6: Booted secondary processor 0x0000000300 [0x410fd083]
>> [ 0.373064] Detected PIPT I-cache on CPU7
>> [ 0.373079] GICv3: CPU7: found redistributor 301 region
>> 0:0x00000000062e0000
>> [ 0.373091] GICv3: CPU7: using allocated LPI pending table
>> @0x0000002178dd0000
>> [ 0.373106] CPU7: Booted secondary processor 0x0000000301 [0x410fd083]
>> [ 0.405124] Detected PIPT I-cache on CPU8
>> [ 0.405143] GICv3: CPU8: found redistributor 400 region
>> 0:0x0000000006300000
>> [ 0.405156] GICv3: CPU8: using allocated LPI pending table
>> @0x0000002178de0000
>> [ 0.405175] CPU8: Booted secondary processor 0x0000000400 [0x410fd083]
>> [ 0.437179] Detected PIPT I-cache on CPU9
>> [ 0.437195] GICv3: CPU9: found redistributor 401 region
>> 0:0x0000000006320000
>> [ 0.437207] GICv3: CPU9: using allocated LPI pending table
>> @0x0000002178df0000
>> [ 0.437223] CPU9: Booted secondary processor 0x0000000401 [0x410fd083]
>> [ 0.469240] Detected PIPT I-cache on CPU10
>> [ 0.469261] GICv3: CPU10: found redistributor 500 region
>> 0:0x0000000006340000
>> [ 0.469273] GICv3: CPU10: using allocated LPI pending table
>> @0x0000002178e00000
>> [ 0.469293] CPU10: Booted secondary processor 0x0000000500
>> [0x410fd083]
>> [ 0.501296] Detected PIPT I-cache on CPU11
>> [ 0.501314] GICv3: CPU11: found redistributor 501 region
>> 0:0x0000000006360000
>> [ 0.501326] GICv3: CPU11: using allocated LPI pending table
>> @0x0000002178e10000
>> [ 0.501342] CPU11: Booted secondary processor 0x0000000501
>> [0x410fd083]
>> [ 0.533362] Detected PIPT I-cache on CPU12
>> [ 0.533385] GICv3: CPU12: found redistributor 600 region
>> 0:0x0000000006380000
>> [ 0.533397] GICv3: CPU12: using allocated LPI pending table
>> @0x0000002178e20000
>> [ 0.533418] CPU12: Booted secondary processor 0x0000000600
>> [0x410fd083]
>> [ 0.565408] Detected PIPT I-cache on CPU13
>> [ 0.565427] GICv3: CPU13: found redistributor 601 region
>> 0:0x00000000063a0000
>> [ 0.565440] GICv3: CPU13: using allocated LPI pending table
>> @0x0000002178e30000
>> [ 0.565455] CPU13: Booted secondary processor 0x0000000601
>> [0x410fd083]
>> [ 0.597470] Detected PIPT I-cache on CPU14
>> [ 0.597494] GICv3: CPU14: found redistributor 700 region
>> 0:0x00000000063c0000
>> [ 0.597507] GICv3: CPU14: using allocated LPI pending table
>> @0x0000002178e40000
>> [ 0.597527] CPU14: Booted secondary processor 0x0000000700
>> [0x410fd083]
>> [ 0.629523] Detected PIPT I-cache on CPU15
>> [ 0.629543] GICv3: CPU15: found redistributor 701 region
>> 0:0x00000000063e0000
>> [ 0.629556] GICv3: CPU15: using allocated LPI pending table
>> @0x0000002178e50000
>> [ 0.629571] CPU15: Booted secondary processor 0x0000000701
>> [0x410fd083]
>> [ 0.629684] smp: Brought up 1 node, 16 CPUs
>> [ 0.931457] SMP: Total of 16 processors activated.
>> [ 0.934986] CPU features: detected: 32-bit EL0 Support
>> [ 0.938858] CPU features: detected: CRC32 instructions
>> [ 0.947732] CPU features: emulated: Privileged Access Never (PAN)
>> using TTBR0_EL1 switching
>> [ 0.954876] CPU: All CPU(s) started at EL2
>> [ 0.957748] alternatives: patching kernel code
>> [ 0.961954] devtmpfs: initialized
>> [ 0.968138] random: get_random_u32 called from
>> bucket_table_alloc.isra.22+0x88/0x1e0 with crng_init=0
>> [ 0.976604] clocksource: jiffies: mask: 0xffffffff max_cycles:
>> 0xffffffff, max_idle_ns: 7645041785100000 ns
>> [ 0.985153] futex hash table entries: 4096 (order: 7, 524288 bytes,
>> linear)
>> [ 0.991643] pinctrl core: initialized pinctrl subsystem
>> [ 0.996213] thermal_sys: Registered thermal governor 'step_wise'
>> [ 0.996473] DMI not present or invalid.
>> [ 1.004023] NET: Registered protocol family 16
>> [ 1.008239] DMA: preallocated 256 KiB pool for atomic allocations
>> [ 1.013102] audit: initializing netlink subsys (disabled)
>> [ 1.017340] audit: type=2000 audit(0.828:1): state=initialized
>> audit_enabled=0 res=1
>> [ 1.023873] cpuidle: using governor ladder
>> [ 1.026734] cpuidle: using governor menu
>> [ 1.029477] hw-breakpoint: found 6 breakpoint and 4 watchpoint
>> registers.
>> [ 1.035332] Serial: AMBA PL011 UART driver
>> [ 1.039319] Machine: SolidRun LX2160A Clearfog CX
>> [ 1.042751] SoC family: QorIQ LX2160A
>> [ 1.045135] SoC ID: svr:0x87361010, Revision: 1.0
>> [ 1.049775] 21c0000.serial: ttyAMA0 at MMIO 0x21c0000 (irq = 17,
>> base_baud = 0) is a SBSA
>> [ 1.056765] printk: console [ttyAMA0] enabled
>> [ 1.062890] printk: bootconsole [pl11] disabled
>> [ 1.069745] 21d0000.serial: ttyAMA1 at MMIO 0x21d0000 (irq = 18,
>> base_baud = 0) is a SBSA
>> [ 1.083284] fsl_mc_bus 80c000000.fsl-mc: MC firmware version: 10.18.0
>> [ 1.091046] fsl_mc_dprc dprc.1: DMA mask not set
>> [ 1.104098] HugeTLB registered 1.00 GiB page size, pre-allocated 0
>> pages
>> [ 1.109500] HugeTLB registered 32.0 MiB page size, pre-allocated 0
>> pages
>> [ 1.114906] HugeTLB registered 2.00 MiB page size, pre-allocated 0
>> pages
>> [ 1.120298] HugeTLB registered 64.0 KiB page size, pre-allocated 0
>> pages
>> [ 1.127238] cryptd: max_cpu_qlen set to 1000
>> [ 1.132187] iommu: Default domain type: Translated (set via kernel
>> command line)
>> [ 1.138411] vgaarb: loaded
>> [ 1.140045] SCSI subsystem initialized
>> [ 1.142660] libata version 3.00 loaded.
>> [ 1.142830] usbcore: registered new interface driver usbfs
>> [ 1.147050] usbcore: registered new interface driver hub
>> [ 1.151152] usbcore: registered new device driver usb
>> [ 1.155269] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery
>> not supported
>> [ 1.161373] i2c i2c-0: IMX I2C adapter registered
>> [ 1.164914] imx-i2c 2020000.i2c: can't get pinctrl, bus recovery
>> not supported
>> [ 1.170923] i2c i2c-1: IMX I2C adapter registered
>> [ 1.174438] imx-i2c 2040000.i2c: can't get pinctrl, bus recovery
>> not supported
>> [ 1.180489] i2c i2c-2: IMX I2C adapter registered
>> [ 1.184034] pps_core: LinuxPPS API ver. 1 registered
>> [ 1.187711] pps_core: Software ver. 5.3.6 - Copyright 2005-2007
>> Rodolfo Giometti <giometti@linux.it>
>> [ 1.195563] PTP clock support registered
>> [ 1.198926] clocksource: Switched to clocksource arch_sys_counter
>> [ 1.409271] VFS: Disk quotas dquot_6.6.0
>> [ 1.411929] VFS: Dquot-cache hash table entries: 512 (order 0, 4096
>> bytes)
>> [ 1.423147] NET: Registered protocol family 2
>> [ 1.426524] tcp_listen_portaddr_hash hash table entries: 4096
>> (order: 6, 294912 bytes, linear)
>> [ 1.434212] TCP established hash table entries: 65536 (order: 7,
>> 524288 bytes, linear)
>> [ 1.441038] TCP bind hash table entries: 65536 (order: 10, 4194304
>> bytes, linear)
>> [ 1.452946] TCP: Hash tables configured (established 65536 bind 65536)
>> [ 1.458362] UDP hash table entries: 4096 (order: 7, 655360 bytes,
>> linear)
>> [ 1.464637] UDP-Lite hash table entries: 4096 (order: 7, 655360
>> bytes, linear)
>> [ 1.471476] NET: Registered protocol family 1
>> [ 1.474948] RPC: Registered named UNIX socket transport module.
>> [ 1.479561] RPC: Registered udp transport module.
>> [ 1.482958] RPC: Registered tcp transport module.
>> [ 1.486348] RPC: Registered tcp NFSv4.1 backchannel transport module.
>> [ 1.491485] PCI: CLS 0 bytes, default 64
>> [ 1.495248] hw perfevents: enabled with armv8_cortex_a72 PMU
>> driver, 7 counters available
>> [ 1.502280] kvm: Limiting the IPA size due to kernel Virtual
>> Address limit
>> [ 1.507851] kvm [1]: IPA Size Limit: 43bits
>> [ 1.511572] kvm [1]: vgic-v2@c0e0000
>> [ 1.513851] kvm [1]: GIC system register CPU interface enabled
>> [ 1.518687] kvm [1]: vgic interrupt IRQ1
>> [ 1.521608] kvm [1]: Hyp mode initialized successfully
>> [ 1.535818] workingset: timestamp_bits=46 max_order=21 bucket_order=0
>> [ 1.549175] NFS: Registering the id_resolver key type
>> [ 1.552967] Key type id_resolver registered
>> [ 1.555844] Key type id_legacy registered
>> [ 1.558661] fuse: init (API version 7.31)
>> [ 1.561605] 9p: Installing v9fs 9p2000 file system support
>> [ 1.566505] io scheduler mq-deadline registered
>> [ 1.569734] io scheduler kyber registered
>> [ 1.573894] layerscape-pcie-gen4 3600000.pcie: host bridge
>> /soc/pcie@3600000 ranges:
>> [ 1.580351] layerscape-pcie-gen4 3600000.pcie: MEM
>> 0x9040000000..0x907fffffff -> 0x0040000000
>> [ 1.588204] layerscape-pcie-gen4 3600000.pcie: PCI host bridge to
>> bus 0000:00
>> [ 1.594036] pci_bus 0000:00: root bus resource [bus 00-ff]
>> [ 1.598216] pci_bus 0000:00: root bus resource [mem
>> 0x9040000000-0x907fffffff] (bus address [0x40000000-0x7fffffff])
>> [ 1.607459] pci 0000:00:00.0: [1957:8d90] type 01 class 0x060400
>> [ 1.612198] pci 0000:00:00.0: enabling Extended Tags
>> [ 1.615912] pci 0000:00:00.0: supports D1 D2
>> [ 1.618869] pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot
>> D3cold
>> [ 1.624897] pci 0000:01:00.0: [1cc1:8201] type 00 class 0x010802
>> [ 1.629666] pci 0000:01:00.0: reg 0x10: [mem
>> 0x9040000000-0x9040003fff 64bit]
>> [ 1.646977] pci 0000:00:00.0: up support 3 enabled 0
>> [ 1.650628] pci 0000:00:00.0: dn support 2 enabled 0
>> [ 1.654743] pci 0000:00:00.0: BAR 8: assigned [mem
>> 0x9040000000-0x90400fffff]
>> [ 1.660577] pci 0000:01:00.0: BAR 0: assigned [mem
>> 0x9040000000-0x9040003fff 64bit]
>> [ 1.666945] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
>> [ 1.670859] pci 0000:00:00.0: bridge window [mem
>> 0x9040000000-0x90400fffff]
>> [ 1.676698] pci 0000:00:00.0: Max Payload Size set to 256/ 256
>> (was 128), Max Read Rq 256
>> [ 1.683858] pci 0000:01:00.0: Max Payload Size set to 256/ 256
>> (was 128), Max Read Rq 256
>> [ 1.691047] pcieport 0000:00:00.0: PCIe capabilities: 0x13
>> [ 1.695230] pcieport 0000:00:00.0: init_service_irqs: -19
>> [ 1.699429] layerscape-pcie-gen4 3800000.pcie: host bridge
>> /soc/pcie@3800000 ranges:
>> [ 1.705877] layerscape-pcie-gen4 3800000.pcie: MEM
>> 0xa040000000..0xa07fffffff -> 0x0040000000
>> [ 1.713713] layerscape-pcie-gen4 3800000.pcie: PCI host bridge to
>> bus 0001:00
>> [ 1.719544] pci_bus 0001:00: root bus resource [bus 00-ff]
>> [ 1.723724] pci_bus 0001:00: root bus resource [mem
>> 0xa040000000-0xa07fffffff] (bus address [0x40000000-0x7fffffff])
>> [ 1.732950] pci 0001:00:00.0: [1957:8d90] type 01 class 0x060400
>> [ 1.737694] pci 0001:00:00.0: enabling Extended Tags
>> [ 1.741407] pci 0001:00:00.0: supports D1 D2
>> [ 1.744371] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot
>> D3cold
>> [ 1.750511] pci 0001:01:00.0: [15b3:6750] type 00 class 0x020000
>> [ 1.755600] pci 0001:01:00.0: reg 0x10: [mem
>> 0xa040000000-0xa0400fffff 64bit]
>> [ 1.761632] pci 0001:01:00.0: reg 0x18: [mem
>> 0xa040800000-0xa040ffffff 64bit pref]
>> [ 1.768286] pci 0001:01:00.0: reg 0x30: [mem
>> 0xa041000000-0xa0410fffff pref]
>> [ 1.787013] pci 0001:00:00.0: up support 3 enabled 0
>> [ 1.790665] pci 0001:00:00.0: dn support 1 enabled 0
>> [ 1.794787] pci 0001:00:00.0: BAR 9: assigned [mem
>> 0xa040000000-0xa0407fffff 64bit pref]
>> [ 1.801572] pci 0001:00:00.0: BAR 8: assigned [mem
>> 0xa040800000-0xa0409fffff]
>> [ 1.807404] pci 0001:01:00.0: BAR 2: assigned [mem
>> 0xa040000000-0xa0407fffff 64bit pref]
>> [ 1.814316] pci 0001:01:00.0: BAR 0: assigned [mem
>> 0xa040800000-0xa0408fffff 64bit]
>> [ 1.820793] pci 0001:01:00.0: BAR 6: assigned [mem
>> 0xa040900000-0xa0409fffff pref]
>> [ 1.827056] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
>> [ 1.830977] pci 0001:00:00.0: bridge window [mem
>> 0xa040800000-0xa0409fffff]
>> [ 1.836806] pci 0001:00:00.0: bridge window [mem
>> 0xa040000000-0xa0407fffff 64bit pref]
>> [ 1.843601] pci 0001:00:00.0: Max Payload Size set to 256/ 256
>> (was 128), Max Read Rq 256
>> [ 1.850903] pci 0001:01:00.0: Max Payload Size set to 256/ 256
>> (was 128), Max Read Rq 256
>> [ 1.858079] pcieport 0001:00:00.0: PCIe capabilities: 0x13
>> [ 1.862260] pcieport 0001:00:00.0: init_service_irqs: -19
>> [ 1.867322] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
>> [ 1.874084] arm-smmu 5000000.iommu: probing hardware configuration...
>> [ 1.879225] arm-smmu 5000000.iommu: SMMUv2 with:
>> [ 1.882529] arm-smmu 5000000.iommu: stage 1 translation
>> [ 1.886534] arm-smmu 5000000.iommu: stage 2 translation
>> [ 1.890539] arm-smmu 5000000.iommu: nested translation
>> [ 1.894457] arm-smmu 5000000.iommu: coherent table walk
>> [ 1.898461] arm-smmu 5000000.iommu: (IDR0.CTTW overridden by FW
>> configuration)
>> [ 1.904464] arm-smmu 5000000.iommu: stream matching with 128
>> register groups
>> [ 1.910294] arm-smmu 5000000.iommu: 64 context banks (0 stage-2
>> only)
>> [ 1.915519] arm-smmu 5000000.iommu: Supported page sizes:
>> 0x61311000
>> [ 1.920653] arm-smmu 5000000.iommu: Stage-1: 48-bit VA ->
>> 48-bit IPA
>> [ 1.925786] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA ->
>> 48-bit PA
>> [ 1.946137] loop: module loaded
>> [ 1.948871] nvme nvme0: pci function 0000:01:00.0
>> [ 1.952710] ahci-qoriq 3200000.sata: 3200000.sata supply ahci not
>> found, using dummy regulator
>> [ 1.960072] ahci-qoriq 3200000.sata: 3200000.sata supply phy not
>> found, using dummy regulator
>> [ 1.967335] ahci-qoriq 3200000.sata: 3200000.sata supply target not
>> found, using dummy regulator
>> [ 1.974957] ahci-qoriq 3200000.sata: AHCI 0001.0301 32 slots 1
>> ports 6 Gbps 0x1 impl platform mode
>> [ 1.982613] ahci-qoriq 3200000.sata: flags: 64bit ncq sntf pm clo
>> only pmp fbs pio slum part ccc sds apst
>> [ 1.991486] scsi host0: ahci-qoriq
>> [ 1.993859] ata1: SATA max UDMA/133 mmio [mem
>> 0x03200000-0x0320ffff] port 0x100 irq 24
>> [ 2.000561] ahci-qoriq 3210000.sata: 3210000.sata supply ahci not
>> found, using dummy regulator
>> [ 2.007916] ahci-qoriq 3210000.sata: 3210000.sata supply phy not
>> found, using dummy regulator
>> [ 2.015194] ahci-qoriq 3210000.sata: 3210000.sata supply target not
>> found, using dummy regulator
>> [ 2.022788] ahci-qoriq 3210000.sata: AHCI 0001.0301 32 slots 1
>> ports 6 Gbps 0x1 impl platform mode
>> [ 2.030443] ahci-qoriq 3210000.sata: flags: 64bit ncq sntf pm clo
>> only pmp fbs pio slum part ccc sds apst
>> [ 2.039256] scsi host1: ahci-qoriq
>> [ 2.041507] ata2: SATA max UDMA/133 mmio [mem
>> 0x03210000-0x0321ffff] port 0x100 irq 25
>> [ 2.048196] ahci-qoriq 3220000.sata: 3220000.sata supply ahci not
>> found, using dummy regulator
>> [ 2.055550] ahci-qoriq 3220000.sata: 3220000.sata supply phy not
>> found, using dummy regulator
>> [ 2.062811] ahci-qoriq 3220000.sata: 3220000.sata supply target not
>> found, using dummy regulator
>> [ 2.070378] ahci-qoriq 3220000.sata: AHCI 0001.0301 32 slots 1
>> ports 6 Gbps 0x1 impl platform mode
>> [ 2.078032] ahci-qoriq 3220000.sata: flags: 64bit ncq sntf pm clo
>> only pmp fbs pio slum part ccc sds apst
>> [ 2.084600] nvme nvme0: 15/0/0 default/read/poll queues
>> [ 2.086837] scsi host2: ahci-qoriq
>> [ 2.092574] ata3: SATA max UDMA/133 mmio [mem
>> 0x03220000-0x0322ffff] port 0x100 irq 26
>> [ 2.092925] nvme0n1: p1 p2
>> [ 2.099262] ahci-qoriq 3230000.sata: 3230000.sata supply ahci not
>> found, using dummy regulator
>> [ 2.108028] ahci-qoriq 3230000.sata: 3230000.sata supply phy not
>> found, using dummy regulator
>> [ 2.115290] ahci-qoriq 3230000.sata: 3230000.sata supply target not
>> found, using dummy regulator
>> [ 2.122864] ahci-qoriq 3230000.sata: AHCI 0001.0301 32 slots 1
>> ports 6 Gbps 0x1 impl platform mode
>> [ 2.130518] ahci-qoriq 3230000.sata: flags: 64bit ncq sntf pm clo
>> only pmp fbs pio slum part ccc sds apst
>> [ 2.139348] scsi host3: ahci-qoriq
>> [ 2.141598] ata4: SATA max UDMA/133 mmio [mem
>> 0x03230000-0x0323ffff] port 0x100 irq 27
>> [ 2.149539] libphy: Fixed MDIO Bus: probed
>> [ 2.152802] libphy: Freescale XGMAC MDIO Bus: probed
>> [ 2.156799] Qualcomm Atheros AR8035 8b96000:01: probe: irq=-1
>> [ 2.161245] Qualcomm Atheros AR8035 8b96000:01: probe: irq=-1
>> [ 2.165963] libphy: Freescale XGMAC MDIO Bus: probed
>> [ 2.170081] dwc3 3100000.usb: Failed to get clk 'ref': -2
>> [ 2.174468] dwc3 3110000.usb: Failed to get clk 'ref': -2
>> [ 2.179050] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
>> [ 2.184274] ehci-platform: EHCI generic platform driver
>> [ 2.188257] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
>> [ 2.193140] ohci-platform: OHCI generic platform driver
>> [ 2.197268] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
>> [ 2.201470] xhci-hcd xhci-hcd.0.auto: new USB bus registered,
>> assigned bus number 1
>> [ 2.207946] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci
>> version 0x100 quirks 0x0000000002010010
>> [ 2.216064] xhci-hcd xhci-hcd.0.auto: irq 22, io mem 0x03100000
>> [ 2.221416] hub 1-0:1.0: USB hub found
>> [ 2.223894] hub 1-0:1.0: 1 port detected
>> [ 2.226762] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
>> [ 2.230951] xhci-hcd xhci-hcd.0.auto: new USB bus registered,
>> assigned bus number 2
>> [ 2.237305] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
>> [ 2.242572] usb usb2: We don't know the algorithms for LPM for this
>> host, disabling LPM.
>> [ 2.249744] hub 2-0:1.0: USB hub found
>> [ 2.252209] hub 2-0:1.0: 1 port detected
>> [ 2.255118] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
>> [ 2.259309] xhci-hcd xhci-hcd.1.auto: new USB bus registered,
>> assigned bus number 3
>> [ 2.265760] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci
>> version 0x100 quirks 0x0000000002010010
>> [ 2.273872] xhci-hcd xhci-hcd.1.auto: irq 23, io mem 0x03110000
>> [ 2.279084] hub 3-0:1.0: USB hub found
>> [ 2.281538] hub 3-0:1.0: 1 port detected
>> [ 2.284380] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
>> [ 2.288571] xhci-hcd xhci-hcd.1.auto: new USB bus registered,
>> assigned bus number 4
>> [ 2.294930] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
>> [ 2.300190] usb usb4: We don't know the algorithms for LPM for this
>> host, disabling LPM.
>> [ 2.307363] hub 4-0:1.0: USB hub found
>> [ 2.309817] hub 4-0:1.0: 1 port detected
>> [ 2.312750] usbcore: registered new interface driver usb-storage
>> [ 2.317173] ata1: SATA link down (SStatus 0 SControl 300)
>> [ 2.317696] mousedev: PS/2 mouse device common for all mice
>> [ 2.331955] rtc-pcf2127-i2c 2-0051: registered as rtc0
>> [ 2.335876] i2c /dev entries driver
>> [ 2.339327] i2c i2c-0: Added multiplexed i2c bus 3
>> [ 2.343067] i2c i2c-0: Added multiplexed i2c bus 4
>> [ 2.346783] i2c i2c-0: Added multiplexed i2c bus 5
>> [ 2.350507] i2c i2c-0: Added multiplexed i2c bus 6
>> [ 2.354164] i2c i2c-0: Added multiplexed i2c bus 7
>> [ 2.357821] i2c i2c-0: Added multiplexed i2c bus 8
>> [ 2.361159] ata2: SATA link down (SStatus 0 SControl 300)
>> [ 2.361480] i2c i2c-0: Added multiplexed i2c bus 9
>> [ 2.369047] i2c i2c-0: Added multiplexed i2c bus 10
>> [ 2.372627] pca954x 0-0077: registered 8 multiplexed busses for I2C
>> mux pca9547
>> [ 2.378783] IR NEC protocol handler initialized
>> [ 2.382010] IR RC5(x/sz) protocol handler initialized
>> [ 2.385755] IR RC6 protocol handler initialized
>> [ 2.388977] IR JVC protocol handler initialized
>> [ 2.392200] IR Sony protocol handler initialized
>> [ 2.395513] IR SANYO protocol handler initialized
>> [ 2.398903] IR Sharp protocol handler initialized
>> [ 2.402300] IR MCE Keyboard/mouse protocol handler initialized
>> [ 2.406827] IR XMP protocol handler initialized
>> [ 2.413367] amc6821 4-0018: Error reading configuration register,
>> aborting.
>> [ 2.417180] ata3: SATA link down (SStatus 0 SControl 300)
>> [ 2.419034] amc6821: probe of 4-0018 failed with error -5
>> [ 2.427436] sdhci: Secure Digital Host Controller Interface driver
>> [ 2.432314] sdhci: Copyright(c) Pierre Ossman
>> [ 2.435384] sdhci-pltfm: SDHCI platform and OF driver helper
>> [ 2.461157] ata4: SATA link down (SStatus 0 SControl 300)
>> [ 2.465487] mmc0: SDHCI controller on 2140000.esdhc [2140000.esdhc]
>> using ADMA 64-bit
>> [ 2.494954] mmc1: SDHCI controller on 2150000.esdhc [2150000.esdhc]
>> using ADMA 64-bit
>> [ 2.502071] ledtrig-cpu: registered to indicate activity on CPUs
>> [ 2.507175] caam 8000000.crypto: device ID = 0x0a1a020000000000
>> (Era 10)
>> [ 2.508538] mmc0: new high speed SDHC card at address aaaa
>> [ 2.512572] caam 8000000.crypto: job rings = 3, qi = 1
>> [ 2.521006] mmcblk0: mmc0:aaaa SU04G 3.69 GiB (ro)
>> [ 2.525840] caam algorithms registered in /proc/crypto
>> [ 2.532365] caam 8000000.crypto: caam pkc algorithms registered in
>> /proc/crypto
>> [ 2.539400] caam_jr 8010000.jr: registering rng-caam
>> [ 2.543736] usbcore: registered new interface driver usbhid
>> [ 2.548007] usbhid: USB HID core driver
>> [ 2.551148] NET: Registered protocol family 10
>> [ 2.554963] Segment Routing with IPv6
>> [ 2.557343] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
>> [ 2.562313] NET: Registered protocol family 17
>> [ 2.565629] 9pnet: Installing 9P2000 support
>> [ 2.568641] Key type dns_resolver registered
>> [ 2.571820] registered taskstats version 1
>> [ 2.578646] fsl_mc_dprc dprc.1: Adding to iommu group 0
>> [ 2.584473] mmc1: new HS400 MMC card at address 0001
>> [ 2.592566] mmcblk1: mmc1:0001 DF4064 58.2 GiB
>> [ 2.595945] mmcblk1boot0: mmc1:0001 DF4064 partition 1 4.00 MiB
>> [ 2.600717] mmcblk1boot1: mmc1:0001 DF4064 partition 2 4.00 MiB
>> [ 2.605471] mmcblk1rpmb: mmc1:0001 DF4064 partition 3 4.00 MiB,
>> chardev (246:0)
>> [ 2.612749] mmcblk1: p1 p2
>> [ 2.622945] usb 3-1: new high-speed USB device number 2 using xhci-hcd
>> [ 2.642000] fsl_dpaa2_eth dpni.0: Adding to iommu group 0
>> [ 2.646254] fsl_mc_dprc dprc.1: No more resources of type dpmcp left
>> [ 2.651688] fsl_mc_allocator dpbp.1: Adding to iommu group 0
>> [ 2.656161] fsl_mc_allocator dpbp.0: Adding to iommu group 0
>> [ 2.662117] fsl_mc_allocator dpmcp.35: Adding to iommu group 0
>> [ 2.667765] fsl_mc_allocator dpmcp.34: Adding to iommu group 0
>> [ 2.673422] fsl_mc_allocator dpmcp.33: Adding to iommu group 0
>> [ 2.679071] fsl_mc_allocator dpmcp.32: Adding to iommu group 0
>> [ 2.684267] hub 3-1:1.0: USB hub found
>> [ 2.684727] fsl_mc_allocator dpmcp.31: Adding to iommu group 0
>> [ 2.686736] hub 3-1:1.0: 4 ports detected
>> [ 2.692343] fsl_mc_allocator dpmcp.30: Adding to iommu group 0
>> [ 2.699627] fsl_mc_allocator dpmcp.29: Adding to iommu group 0
>> [ 2.705265] fsl_mc_allocator dpmcp.28: Adding to iommu group 0
>> [ 2.710952] fsl_mc_allocator dpmcp.27: Adding to iommu group 0
>> [ 2.716596] fsl_mc_allocator dpmcp.26: Adding to iommu group 0
>> [ 2.722243] fsl_mc_allocator dpmcp.25: Adding to iommu group 0
>> [ 2.727897] fsl_mc_allocator dpmcp.24: Adding to iommu group 0
>> [ 2.733550] fsl_mc_allocator dpmcp.23: Adding to iommu group 0
>> [ 2.739198] fsl_mc_allocator dpmcp.22: Adding to iommu group 0
>> [ 2.744853] fsl_mc_allocator dpmcp.21: Adding to iommu group 0
>> [ 2.750495] fsl_mc_allocator dpmcp.20: Adding to iommu group 0
>> [ 2.756161] fsl_mc_allocator dpmcp.19: Adding to iommu group 0
>> [ 2.761803] fsl_mc_allocator dpmcp.18: Adding to iommu group 0
>> [ 2.767473] fsl_mc_allocator dpmcp.17: Adding to iommu group 0
>> [ 2.773117] fsl_mc_allocator dpmcp.16: Adding to iommu group 0
>> [ 2.778768] fsl_mc_allocator dpmcp.15: Adding to iommu group 0
>> [ 2.782959] usb 4-1: new SuperSpeed Gen 1 USB device number 2 using
>> xhci-hcd
>> [ 2.784414] fsl_mc_allocator dpmcp.14: Adding to iommu group 0
>> [ 2.794669] fsl_mc_allocator dpmcp.13: Adding to iommu group 0
>> [ 2.800309] fsl_mc_allocator dpmcp.12: Adding to iommu group 0
>> [ 2.805969] fsl_mc_allocator dpmcp.11: Adding to iommu group 0
>> [ 2.811625] fsl_mc_allocator dpmcp.10: Adding to iommu group 0
>> [ 2.817271] fsl_mc_allocator dpmcp.9: Adding to iommu group 0
>> [ 2.822845] fsl_mc_allocator dpmcp.8: Adding to iommu group 0
>> [ 2.828243] hub 4-1:1.0: USB hub found
>> [ 2.828420] fsl_mc_allocator dpmcp.7: Adding to iommu group 0
>> [ 2.830710] hub 4-1:1.0: 4 ports detected
>> [ 2.836276] fsl_mc_allocator dpmcp.6: Adding to iommu group 0
>> [ 2.843415] fsl_mc_allocator dpmcp.5: Adding to iommu group 0
>> [ 2.848975] fsl_mc_allocator dpmcp.4: Adding to iommu group 0
>> [ 2.851038] random: fast init done
>> [ 2.854534] fsl_mc_allocator dpmcp.3: Adding to iommu group 0
>> [ 2.861060] fsl_mc_allocator dpmcp.2: Adding to iommu group 0
>> [ 2.866622] fsl_mc_allocator dpmcp.1: Adding to iommu group 0
>> [ 2.874308] fsl_mc_dpio dpio.15: Adding to iommu group 0
>> [ 2.882022] fsl_mc_dpio dpio.15: probed
>> [ 2.888261] fsl_mc_dpio dpio.14: Adding to iommu group 0
>> [ 2.895912] fsl_mc_dpio dpio.14: probed
>> [ 2.902061] fsl_mc_dpio dpio.13: Adding to iommu group 0
>> [ 2.909710] fsl_mc_dpio dpio.13: probed
>> [ 2.915939] fsl_mc_dpio dpio.12: Adding to iommu group 0
>> [ 2.923591] fsl_mc_dpio dpio.12: probed
>> [ 2.929752] fsl_mc_dpio dpio.11: Adding to iommu group 0
>> [ 2.937396] fsl_mc_dpio dpio.11: probed
>> [ 2.943628] fsl_mc_dpio dpio.10: Adding to iommu group 0
>> [ 2.951283] fsl_mc_dpio dpio.10: probed
>> [ 2.957446] fsl_mc_dpio dpio.9: Adding to iommu group 0
>> [ 2.965012] fsl_mc_dpio dpio.9: probed
>> [ 2.971167] fsl_mc_dpio dpio.8: Adding to iommu group 0
>> [ 2.978776] fsl_mc_dpio dpio.8: probed
>> [ 2.984923] fsl_mc_dpio dpio.7: Adding to iommu group 0
>> [ 2.992537] fsl_mc_dpio dpio.7: probed
>> [ 2.998684] fsl_mc_dpio dpio.6: Adding to iommu group 0
>> [ 3.006299] fsl_mc_dpio dpio.6: probed
>> [ 3.012440] fsl_mc_dpio dpio.5: Adding to iommu group 0
>> [ 3.020064] fsl_mc_dpio dpio.5: probed
>> [ 3.026190] fsl_mc_dpio dpio.4: Adding to iommu group 0
>> [ 3.033754] fsl_mc_dpio dpio.4: probed
>> [ 3.038937] usb 3-1.3: new high-speed USB device number 3 using
>> xhci-hcd
>> [ 3.039844] fsl_mc_dpio dpio.3: Adding to iommu group 0
>> [ 3.051890] fsl_mc_dpio dpio.3: probed
>> [ 3.058009] fsl_mc_dpio dpio.2: Adding to iommu group 0
>> [ 3.065609] fsl_mc_dpio dpio.2: probed
>> [ 3.071763] fsl_mc_dpio dpio.1: Adding to iommu group 0
>> [ 3.079384] fsl_mc_dpio dpio.1: probed
>> [ 3.085521] fsl_mc_dpio dpio.0: Adding to iommu group 0
>> [ 3.093136] fsl_mc_dpio dpio.0: probed
>> [ 3.096201] fsl_mc_allocator dpcon.31: Adding to iommu group 0
>> [ 3.100196] hub 3-1.3:1.0: USB hub found
>> [ 3.100860] fsl_mc_allocator dpcon.30: Adding to iommu group 0
>> [ 3.103374] hub 3-1.3:1.0: 4 ports detected
>> [ 3.107983] fsl_mc_allocator dpcon.29: Adding to iommu group 0
>> [ 3.115381] fsl_mc_allocator dpcon.28: Adding to iommu group 0
>> [ 3.120030] fsl_mc_allocator dpcon.27: Adding to iommu group 0
>> [ 3.124682] fsl_mc_allocator dpcon.26: Adding to iommu group 0
>> [ 3.129333] fsl_mc_allocator dpcon.25: Adding to iommu group 0
>> [ 3.133987] fsl_mc_allocator dpcon.24: Adding to iommu group 0
>> [ 3.138642] fsl_mc_allocator dpcon.23: Adding to iommu group 0
>> [ 3.143294] fsl_mc_allocator dpcon.22: Adding to iommu group 0
>> [ 3.147946] fsl_mc_allocator dpcon.21: Adding to iommu group 0
>> [ 3.152597] fsl_mc_allocator dpcon.20: Adding to iommu group 0
>> [ 3.157250] fsl_mc_allocator dpcon.19: Adding to iommu group 0
>> [ 3.161903] fsl_mc_allocator dpcon.18: Adding to iommu group 0
>> [ 3.166559] fsl_mc_allocator dpcon.17: Adding to iommu group 0
>> [ 3.171217] fsl_mc_allocator dpcon.16: Adding to iommu group 0
>> [ 3.175871] fsl_mc_allocator dpcon.15: Adding to iommu group 0
>> [ 3.180533] fsl_mc_allocator dpcon.14: Adding to iommu group 0
>> [ 3.185188] fsl_mc_allocator dpcon.13: Adding to iommu group 0
>> [ 3.189844] fsl_mc_allocator dpcon.12: Adding to iommu group 0
>> [ 3.194499] fsl_mc_allocator dpcon.11: Adding to iommu group 0
>> [ 3.199153] fsl_mc_allocator dpcon.10: Adding to iommu group 0
>> [ 3.203810] fsl_mc_allocator dpcon.9: Adding to iommu group 0
>> [ 3.208385] fsl_mc_allocator dpcon.8: Adding to iommu group 0
>> [ 3.212956] fsl_mc_allocator dpcon.7: Adding to iommu group 0
>> [ 3.217526] fsl_mc_allocator dpcon.6: Adding to iommu group 0
>> [ 3.222096] fsl_mc_allocator dpcon.5: Adding to iommu group 0
>> [ 3.226667] fsl_mc_allocator dpcon.4: Adding to iommu group 0
>> [ 3.231237] fsl_mc_allocator dpcon.3: Adding to iommu group 0
>> [ 3.235812] fsl_mc_allocator dpcon.2: Adding to iommu group 0
>> [ 3.240383] fsl_mc_allocator dpcon.1: Adding to iommu group 0
>> [ 3.244955] fsl_mc_allocator dpcon.0: Adding to iommu group 0
>> [ 3.252565] fsl_mc_dprc dprc.1: DPRC device bound to driver
>> [ 3.257032] libphy: SFP I2C Bus: probed
>> [ 3.259658] sfp sfp-0: Host maximum power 2.0W
>> [ 3.262929] sfp sfp-0: No tx_disable pin: SFP modules will always
>> be emitting.
>> [ 3.269061] libphy: SFP I2C Bus: probed
>> [ 3.271642] sfp sfp-1: Host maximum power 2.0W
>> [ 3.274884] sfp sfp-1: No tx_disable pin: SFP modules will always
>> be emitting.
>> [ 3.280979] libphy: SFP I2C Bus: probed
>> [ 3.283559] sfp sfp-2: Host maximum power 2.0W
>> [ 3.286819] sfp sfp-2: No tx_disable pin: SFP modules will always
>> be emitting.
>> [ 3.292948] libphy: SFP I2C Bus: probed
>> [ 3.295529] sfp sfp-3: Host maximum power 2.0W
>> [ 3.298768] sfp sfp-3: No tx_disable pin: SFP modules will always
>> be emitting.
>> [ 3.456609] fsl_dpaa2_eth dpni.0 (unnamed net_device)
>> (uninitialized): PHY [8b96000:01] driver [Qualcomm Atheros AR8035]
>> (irq=POLL)
>> [ 3.467153] fsl_dpaa2_eth dpni.0 (unnamed net_device)
>> (uninitialized): phy: setting supported 000,00000200,000062ea
>> advertising 000,00000200,000062ea
>> [ 3.468341] fsl_dpaa2_eth dpni.0: Probed interface eth0
>> [ 3.472672] input: gpio-keys as
>> /devices/platform/gpio-keys/input/input0
>> [ 3.479780] rtc-pcf2127-i2c 2-0051: setting system clock to
>> 2020-02-28T09:56:18 UTC (1582883778)
>> [ 3.490224] EXT4-fs (nvme0n1p2): mounted filesystem with ordered
>> data mode. Opts: (null)
>> [ 3.497082] VFS: Mounted root (ext4 filesystem) readonly on device
>> 259:2.
>> [ 3.503193] devtmpfs: mounted
>> [ 3.505079] Freeing unused kernel memory: 960K
>> [ 3.534993] Run /sbin/init as init process
>>
>> When asking for more network interfaces, more "Adding to iommu group"
>> messages get spat out:
>>
>> [ 446.040825] fsl_dpaa2_eth dpni.1: Adding to iommu group 0
>> [ 446.201254] libphy: Freescale XGMAC MDIO Bus: probed
>> [ 446.206552] fsl_dpaa2_eth dpni.1: Probed interface eth1
>> [ 446.210715] fsl_mc_allocator dpbp.2: Adding to iommu group 0
>> [ 446.216838] fsl_mc_allocator dpmcp.36: Adding to iommu group 0
>> [ 446.224808] fsl_mc_allocator dpcon.47: Adding to iommu group 0
>> [ 446.229935] fsl_mc_allocator dpcon.46: Adding to iommu group 0
>> [ 446.234685] fsl_mc_allocator dpcon.45: Adding to iommu group 0
>> [ 446.239431] fsl_mc_allocator dpcon.44: Adding to iommu group 0
>> [ 446.244179] fsl_mc_allocator dpcon.43: Adding to iommu group 0
>> [ 446.251725] fsl_mc_allocator dpcon.42: Adding to iommu group 0
>> [ 446.258952] fsl_mc_allocator dpcon.41: Adding to iommu group 0
>> [ 446.263666] fsl_mc_allocator dpcon.40: Adding to iommu group 0
>> [ 446.268377] fsl_mc_allocator dpcon.39: Adding to iommu group 0
>> [ 446.273086] fsl_mc_allocator dpcon.38: Adding to iommu group 0
>> [ 446.277814] fsl_mc_allocator dpcon.37: Adding to iommu group 0
>> [ 446.282517] fsl_mc_allocator dpcon.36: Adding to iommu group 0
>> [ 446.287228] fsl_mc_allocator dpcon.35: Adding to iommu group 0
>> [ 446.291935] fsl_mc_allocator dpcon.34: Adding to iommu group 0
>> [ 446.296641] fsl_mc_allocator dpcon.33: Adding to iommu group 0
>> [ 446.301354] fsl_mc_allocator dpcon.32: Adding to iommu group 0
>> [ 446.893939] fsl_dpaa2_eth dpni.2: Adding to iommu group 0
>> [ 447.052868] libphy: Freescale XGMAC MDIO Bus: probed
>> [ 447.058223] fsl_dpaa2_eth dpni.2: Probed interface eth2
>> [ 447.062425] fsl_mc_allocator dpbp.3: Adding to iommu group 0
>> [ 447.068813] fsl_mc_allocator dpmcp.37: Adding to iommu group 0
>> [ 447.074280] fsl_mc_allocator dpcon.63: Adding to iommu group 0
>> [ 447.078995] fsl_mc_allocator dpcon.62: Adding to iommu group 0
>> [ 447.088690] fsl_mc_allocator dpcon.61: Adding to iommu group 0
>> [ 447.093639] fsl_mc_allocator dpcon.60: Adding to iommu group 0
>> [ 447.098369] fsl_mc_allocator dpcon.59: Adding to iommu group 0
>> [ 447.103089] fsl_mc_allocator dpcon.58: Adding to iommu group 0
>> [ 447.107811] fsl_mc_allocator dpcon.57: Adding to iommu group 0
>> [ 447.112525] fsl_mc_allocator dpcon.56: Adding to iommu group 0
>> [ 447.117244] fsl_mc_allocator dpcon.55: Adding to iommu group 0
>> [ 447.121962] fsl_mc_allocator dpcon.54: Adding to iommu group 0
>> [ 447.126680] fsl_mc_allocator dpcon.53: Adding to iommu group 0
>> [ 447.131392] fsl_mc_allocator dpcon.52: Adding to iommu group 0
>> [ 447.136107] fsl_mc_allocator dpcon.51: Adding to iommu group 0
>> [ 447.140820] fsl_mc_allocator dpcon.50: Adding to iommu group 0
>> [ 447.145535] fsl_mc_allocator dpcon.49: Adding to iommu group 0
>> [ 447.150249] fsl_mc_allocator dpcon.48: Adding to iommu group 0
>> [ 447.710694] fsl_dpaa2_eth dpni.3: Adding to iommu group 0
>> [ 447.888120] libphy: Freescale XGMAC MDIO Bus: probed
>> [ 447.893479] fsl_dpaa2_eth dpni.3: Probed interface eth3
>> [ 447.897740] fsl_mc_allocator dpbp.4: Adding to iommu group 0
>> [ 447.904488] fsl_mc_allocator dpmcp.38: Adding to iommu group 0
>> [ 447.909994] fsl_mc_allocator dpcon.79: Adding to iommu group 0
>> [ 447.914717] fsl_mc_allocator dpcon.78: Adding to iommu group 0
>> [ 447.919852] fsl_mc_allocator dpcon.77: Adding to iommu group 0
>> [ 447.924720] fsl_mc_allocator dpcon.76: Adding to iommu group 0
>> [ 447.931979] fsl_mc_allocator dpcon.75: Adding to iommu group 0
>> [ 447.939172] fsl_mc_allocator dpcon.74: Adding to iommu group 0
>> [ 447.943886] fsl_mc_allocator dpcon.73: Adding to iommu group 0
>> [ 447.948604] fsl_mc_allocator dpcon.72: Adding to iommu group 0
>> [ 447.953319] fsl_mc_allocator dpcon.71: Adding to iommu group 0
>> [ 447.958035] fsl_mc_allocator dpcon.70: Adding to iommu group 0
>> [ 447.965445] fsl_mc_allocator dpcon.69: Adding to iommu group 0
>> [ 447.972653] fsl_mc_allocator dpcon.68: Adding to iommu group 0
>> [ 447.977376] fsl_mc_allocator dpcon.67: Adding to iommu group 0
>> [ 447.982097] fsl_mc_allocator dpcon.66: Adding to iommu group 0
>> [ 447.986816] fsl_mc_allocator dpcon.65: Adding to iommu group 0
>> [ 447.991532] fsl_mc_allocator dpcon.64: Adding to iommu group 0
>> [ 448.737198] fsl_dpaa2_eth dpni.4: Adding to iommu group 0
>> [ 448.894480] libphy: Freescale XGMAC MDIO Bus: probed
>> [ 448.899785] fsl_dpaa2_eth dpni.4: Probed interface eth4
>> [ 448.904077] fsl_mc_allocator dpbp.5: Adding to iommu group 0
>> [ 448.909817] fsl_mc_allocator dpmcp.39: Adding to iommu group 0
>> [ 448.915340] fsl_mc_allocator dpcon.95: Adding to iommu group 0
>> [ 448.920068] fsl_mc_allocator dpcon.94: Adding to iommu group 0
>> [ 448.924789] fsl_mc_allocator dpcon.93: Adding to iommu group 0
>> [ 448.929689] fsl_mc_allocator dpcon.92: Adding to iommu group 0
>> [ 448.934436] fsl_mc_allocator dpcon.91: Adding to iommu group 0
>> [ 448.939159] fsl_mc_allocator dpcon.90: Adding to iommu group 0
>> [ 448.943882] fsl_mc_allocator dpcon.89: Adding to iommu group 0
>> [ 448.948607] fsl_mc_allocator dpcon.88: Adding to iommu group 0
>> [ 448.953327] fsl_mc_allocator dpcon.87: Adding to iommu group 0
>> [ 448.958050] fsl_mc_allocator dpcon.86: Adding to iommu group 0
>> [ 448.962771] fsl_mc_allocator dpcon.85: Adding to iommu group 0
>> [ 448.967499] fsl_mc_allocator dpcon.84: Adding to iommu group 0
>> [ 448.972219] fsl_mc_allocator dpcon.83: Adding to iommu group 0
>> [ 448.976941] fsl_mc_allocator dpcon.82: Adding to iommu group 0
>> [ 448.981669] fsl_mc_allocator dpcon.81: Adding to iommu group 0
>> [ 448.986391] fsl_mc_allocator dpcon.80: Adding to iommu group 0
>>
>> # dmesg |grep 'Adding to iommu' | wc -l
>> 164
>> # dmesg |grep -v 'Adding to iommu' | wc -l
>> 551
>>
>> So, 23% of the kernel messages on this platform are "Adding to iommu",
>> which is excessive.
>
> Indeed, however I would note that on most platforms bringing up a
> network interface involves hot-adding 0 devices, so hot-adding 19
> devices as full-blown DMA masters is arguably the root of "excessive"
> already. Per the concern I initially raised, each of those messages
> represents a whole bunch of internal allocation and bookkeeping going
> on, which if it isn't necessary would be far better avoided altogether,
> than simply done more quietly.
>
> Laurentiu, I guess at the moment the nature of the of_dma_configure()
> integration means we end up treating all DPAA2 objects identically, but
> do you think we have scope to be a bit cleverer in that regard?
> Presumably not every type of object that shows up on the fsl_mc bus is
> really an independent DMA master, so if we could skip doing the full
> DMA/IOMMU/MSI setup for the ones that don't need it, it would work out
> nicer all round. In fact your .dma_configure proposal (which I'll try to
> take a proper look at next week) couldn't have come at a better time for
> that argument :)
>
Just FYI, I've tried Robin's suggestion and things greatly improved [1],
so I think we can leave the iommu group messages alone.
[1]
# dmesg |grep 'Adding to iommu' | wc -l
7
# dmesg |grep -v 'Adding to iommu' | wc -l
512
---
Thanks & Best Regards, Laurentiu
_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH] iommu: silence iommu group prints
2020-03-03 14:18 ` Laurentiu Tudor
@ 2020-03-03 15:49 ` Russell King - ARM Linux admin
2020-03-03 15:55 ` Laurentiu Tudor
0 siblings, 1 reply; 24+ messages in thread
From: Russell King - ARM Linux admin @ 2020-03-03 15:49 UTC (permalink / raw)
To: Laurentiu Tudor
Cc: Diana Madalina Craciun, iommu, Robin Murphy, Ioana Ciornei
On Tue, Mar 03, 2020 at 04:18:57PM +0200, Laurentiu Tudor wrote:
>
>
> On 28.02.2020 20:32, Robin Murphy wrote:
> > [ +Laurentiu ]
> >
> > Hi Russell,
> >
> > Thanks for sharing a log, now I properly understand what's up... further
> > comments at the end (for context).
> >
> > On 28/02/2020 10:06 am, Russell King - ARM Linux admin wrote:
> > > On Fri, Feb 28, 2020 at 09:33:40AM +0000, John Garry wrote:
> > > > On 28/02/2020 02:16, Lu Baolu wrote:
> > > > > Hi,
> > > > >
> > > > > On 2020/2/27 19:57, Russell King wrote:
> > > > > > On the LX2160A, there are lots (about 160) of IOMMU messages produced
> > > > > > during boot; this is excessive. Reduce the severity of these messages
> > > > > > to debug level.
> > > > > >
> > > > > > Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
> > > > > > ---
> > > > > > drivers/iommu/iommu.c | 4 ++--
> > > > > > 1 file changed, 2 insertions(+), 2 deletions(-)
> > > > > >
> > > > > > diff --git a/drivers/iommu/iommu.c b/drivers/iommu/iommu.c
> > > > > > index 3ead597e1c57..304281ec623b 100644
> > > > > > --- a/drivers/iommu/iommu.c
> > > > > > +++ b/drivers/iommu/iommu.c
> > > > > > @@ -741,7 +741,7 @@ int iommu_group_add_device(struct iommu_group
> > > > > > *group, struct device *dev)
> > > > > > trace_add_device_to_group(group->id, dev);
> > > > > > - dev_info(dev, "Adding to iommu group %d\n", group->id);
> > > > > > + dev_dbg(dev, "Adding to iommu group %d\n", group->id);
> > > > >
> > > > > I'm not strongly against this. But to me this message seems
> > > > > to be a good
> > > > > indicator that a device was probed successfully by the iommu subsystem.
> > > > > Keeping it in the default kernel message always helps to the kernel
> > > > > debugging.
> > > > >
> > > >
> > > > I would tend to agree.
> > >
> > > Here's the boot messages. Notice how many of these "Adding to iommu
> > > group" messages there are:
> > >
> > > [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083]
> > > [ 0.000000] Linux version 5.5.0+ (rmk@rmk-PC) (gcc version 4.9.2
> > > (GCC)) #655 SMP PREEMPT Fri Feb 28 09:54:47 GMT 2020
> > > [ 0.000000] Machine model: SolidRun LX2160A Clearfog CX
> > > [ 0.000000] earlycon: pl11 at MMIO32 0x00000000021c0000 (options '')
> > > [ 0.000000] printk: bootconsole [pl11] enabled
> > > [ 0.000000] efi: Getting EFI parameters from FDT:
> > > [ 0.000000] efi: UEFI not found.
> > > [ 0.000000] cma: Reserved 32 MiB at 0x00000000f9c00000
> > > [ 0.000000] On node 0 totalpages: 1555968
> > > [ 0.000000] DMA zone: 4096 pages used for memmap
> > > [ 0.000000] DMA zone: 0 pages reserved
> > > [ 0.000000] DMA zone: 262144 pages, LIFO batch:63
> > > [ 0.000000] DMA32 zone: 3832 pages used for memmap
> > > [ 0.000000] DMA32 zone: 245248 pages, LIFO batch:63
> > > [ 0.000000] Normal zone: 16384 pages used for memmap
> > > [ 0.000000] Normal zone: 1048576 pages, LIFO batch:63
> > > [ 0.000000] psci: probing for conduit method from DT.
> > > [ 0.000000] psci: PSCIv1.1 detected in firmware.
> > > [ 0.000000] psci: Using standard PSCI v0.2 function IDs
> > > [ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
> > > [ 0.000000] psci: SMC Calling Convention v1.1
> > > [ 0.000000] percpu: Embedded 31 pages/cpu s88968 r8192 d29816 u126976
> > > [ 0.000000] pcpu-alloc: s88968 r8192 d29816 u126976 alloc=31*4096
> > > [ 0.000000] pcpu-alloc: [0] 00 [0] 01 [0] 02 [0] 03 [0] 04 [0] 05
> > > [0] 06 [0] 07
> > > [ 0.000000] pcpu-alloc: [0] 08 [0] 09 [0] 10 [0] 11 [0] 12 [0] 13
> > > [0] 14 [0] 15
> > > [ 0.000000] Detected PIPT I-cache on CPU0
> > > [ 0.000000] CPU features: detected: GIC system register CPU interface
> > > [ 0.000000] CPU features: detected: EL2 vector hardening
> > > [ 0.000000] Speculative Store Bypass Disable mitigation not required
> > > [ 0.000000] CPU features: detected: ARM erratum 1319367
> > > [ 0.000000] Built 1 zonelists, mobility grouping on. Total
> > > pages: 1531656
> > > [ 0.000000] Kernel command line: console=ttyAMA0,115200
> > > root=PARTUUID=c7837e2f-02 rootwait earlycon=pl011,mmio32,0x21c0000
> > > ramdisk_size=0 pci=pcie_bus_perf arm_smmu.disable_bypass=0
> > > iommu.passthrough=0
> > > [ 0.000000] Dentry cache hash table entries: 1048576 (order: 11,
> > > 8388608 bytes, linear)
> > > [ 0.000000] Inode-cache hash table entries: 524288 (order: 10,
> > > 4194304 bytes, linear)
> > > [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
> > > [ 0.000000] software IO TLB: mapped [mem 0xbbfff000-0xbffff000] (64MB)
> > > [ 0.000000] Memory: 5991500K/6223872K available (10172K kernel
> > > code, 1376K rwdata, 3888K rodata, 960K init, 4326K bss, 199604K
> > > reserved, 32768K cma-reserved)
> > > [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=16,
> > > Nodes=1
> > > [ 0.000000] rcu: Preemptible hierarchical RCU implementation.
> > > [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=64 to
> > > nr_cpu_ids=16.
> > > [ 0.000000] Tasks RCU enabled.
> > > [ 0.000000] rcu: RCU calculated value of scheduler-enlistment
> > > delay is 25 jiffies.
> > > [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16,
> > > nr_cpu_ids=16
> > > [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
> > > [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
> > > [ 0.000000] GICv3: 256 SPIs implemented
> > > [ 0.000000] GICv3: 0 Extended SPIs implemented
> > > [ 0.000000] GICv3: Distributor has no Range Selector support
> > > [ 0.000000] GICv3: 16 PPIs implemented
> > > [ 0.000000] GICv3: no VLPI support, no direct LPI support
> > > [ 0.000000] GICv3: CPU0: found redistributor 0 region
> > > 0:0x0000000006200000
> > > [ 0.000000] ITS [mem 0x06020000-0x0603ffff]
> > > [ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices
> > > @2178d00000 (flat, esz 8, psz 64K, shr 0)
> > > [ 0.000000] ITS: using cache flushing for cmd queue
> > > [ 0.000000] GICv3: using LPI property table @0x0000002178cd0000
> > > [ 0.000000] GIC: using cache flushing for LPI property table
> > > [ 0.000000] GICv3: CPU0: using allocated LPI pending table
> > > @0x0000002178ce0000
> > > [ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys).
> > > [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff
> > > max_cycles: 0x5c409fb33, max_idle_ns: 440795203156 ns
> > > [ 0.000002] sched_clock: 56 bits at 25MHz, resolution 39ns, wraps
> > > every 4398046511103ns
> > > [ 0.006921] Console: colour dummy device 80x25
> > > [ 0.010093] Lock dependency validator: Copyright (c) 2006 Red
> > > Hat, Inc., Ingo Molnar
> > > [ 0.016605] ... MAX_LOCKDEP_SUBCLASSES: 8
> > > [ 0.019421] ... MAX_LOCK_DEPTH: 48
> > > [ 0.022329] ... MAX_LOCKDEP_KEYS: 8192
> > > [ 0.025408] ... CLASSHASH_SIZE: 4096
> > > [ 0.028491] ... MAX_LOCKDEP_ENTRIES: 32768
> > > [ 0.031659] ... MAX_LOCKDEP_CHAINS: 65536
> > > [ 0.034830] ... CHAINHASH_SIZE: 32768
> > > [ 0.037997] memory used by lock dependency info: 3509 kB
> > > [ 0.042135] per task-struct memory footprint: 1920 bytes
> > > [ 0.046292] Calibrating delay loop (skipped), value calculated
> > > using timer frequency.. 50.00 BogoMIPS (lpj=100000)
> > > [ 0.055443] pid_max: default: 32768 minimum: 301
> > > [ 0.058844] LSM: Security Framework initializing
> > > [ 0.062241] Mount-cache hash table entries: 16384 (order: 5,
> > > 131072 bytes, linear)
> > > [ 0.068602] Mountpoint-cache hash table entries: 16384 (order: 5,
> > > 131072 bytes, linear)
> > > [ 0.099452] ASID allocator initialised with 32768 entries
> > > [ 0.111615] rcu: Hierarchical SRCU implementation.
> > > [ 0.119672] Platform MSI: gic-its@6020000 domain created
> > > [ 0.123765] PCI/MSI:
> > > /interrupt-controller@6000000/gic-its@6020000 domain created
> > > [ 0.130045] fsl-mc MSI:
> > > /interrupt-controller@6000000/gic-its@6020000 domain created
> > > [ 0.136572] EFI services will not be available.
> > > [ 0.148587] smp: Bringing up secondary CPUs ...
> > > [ 0.180732] Detected PIPT I-cache on CPU1
> > > [ 0.180749] GICv3: CPU1: found redistributor 1 region
> > > 0:0x0000000006220000
> > > [ 0.180761] GICv3: CPU1: using allocated LPI pending table
> > > @0x0000002178cf0000
> > > [ 0.180781] CPU1: Booted secondary processor 0x0000000001 [0x410fd083]
> > > [ 0.212781] Detected PIPT I-cache on CPU2
> > > [ 0.212797] GICv3: CPU2: found redistributor 100 region
> > > 0:0x0000000006240000
> > > [ 0.212810] GICv3: CPU2: using allocated LPI pending table
> > > @0x0000002178d80000
> > > [ 0.212830] CPU2: Booted secondary processor 0x0000000100 [0x410fd083]
> > > [ 0.244832] Detected PIPT I-cache on CPU3
> > > [ 0.244844] GICv3: CPU3: found redistributor 101 region
> > > 0:0x0000000006260000
> > > [ 0.244855] GICv3: CPU3: using allocated LPI pending table
> > > @0x0000002178d90000
> > > [ 0.244871] CPU3: Booted secondary processor 0x0000000101 [0x410fd083]
> > > [ 0.276894] Detected PIPT I-cache on CPU4
> > > [ 0.276910] GICv3: CPU4: found redistributor 200 region
> > > 0:0x0000000006280000
> > > [ 0.276922] GICv3: CPU4: using allocated LPI pending table
> > > @0x0000002178da0000
> > > [ 0.276941] CPU4: Booted secondary processor 0x0000000200 [0x410fd083]
> > > [ 0.308953] Detected PIPT I-cache on CPU5
> > > [ 0.308966] GICv3: CPU5: found redistributor 201 region
> > > 0:0x00000000062a0000
> > > [ 0.308978] GICv3: CPU5: using allocated LPI pending table
> > > @0x0000002178db0000
> > > [ 0.308994] CPU5: Booted secondary processor 0x0000000201 [0x410fd083]
> > > [ 0.341009] Detected PIPT I-cache on CPU6
> > > [ 0.341027] GICv3: CPU6: found redistributor 300 region
> > > 0:0x00000000062c0000
> > > [ 0.341039] GICv3: CPU6: using allocated LPI pending table
> > > @0x0000002178dc0000
> > > [ 0.341058] CPU6: Booted secondary processor 0x0000000300 [0x410fd083]
> > > [ 0.373064] Detected PIPT I-cache on CPU7
> > > [ 0.373079] GICv3: CPU7: found redistributor 301 region
> > > 0:0x00000000062e0000
> > > [ 0.373091] GICv3: CPU7: using allocated LPI pending table
> > > @0x0000002178dd0000
> > > [ 0.373106] CPU7: Booted secondary processor 0x0000000301 [0x410fd083]
> > > [ 0.405124] Detected PIPT I-cache on CPU8
> > > [ 0.405143] GICv3: CPU8: found redistributor 400 region
> > > 0:0x0000000006300000
> > > [ 0.405156] GICv3: CPU8: using allocated LPI pending table
> > > @0x0000002178de0000
> > > [ 0.405175] CPU8: Booted secondary processor 0x0000000400 [0x410fd083]
> > > [ 0.437179] Detected PIPT I-cache on CPU9
> > > [ 0.437195] GICv3: CPU9: found redistributor 401 region
> > > 0:0x0000000006320000
> > > [ 0.437207] GICv3: CPU9: using allocated LPI pending table
> > > @0x0000002178df0000
> > > [ 0.437223] CPU9: Booted secondary processor 0x0000000401 [0x410fd083]
> > > [ 0.469240] Detected PIPT I-cache on CPU10
> > > [ 0.469261] GICv3: CPU10: found redistributor 500 region
> > > 0:0x0000000006340000
> > > [ 0.469273] GICv3: CPU10: using allocated LPI pending table
> > > @0x0000002178e00000
> > > [ 0.469293] CPU10: Booted secondary processor 0x0000000500
> > > [0x410fd083]
> > > [ 0.501296] Detected PIPT I-cache on CPU11
> > > [ 0.501314] GICv3: CPU11: found redistributor 501 region
> > > 0:0x0000000006360000
> > > [ 0.501326] GICv3: CPU11: using allocated LPI pending table
> > > @0x0000002178e10000
> > > [ 0.501342] CPU11: Booted secondary processor 0x0000000501
> > > [0x410fd083]
> > > [ 0.533362] Detected PIPT I-cache on CPU12
> > > [ 0.533385] GICv3: CPU12: found redistributor 600 region
> > > 0:0x0000000006380000
> > > [ 0.533397] GICv3: CPU12: using allocated LPI pending table
> > > @0x0000002178e20000
> > > [ 0.533418] CPU12: Booted secondary processor 0x0000000600
> > > [0x410fd083]
> > > [ 0.565408] Detected PIPT I-cache on CPU13
> > > [ 0.565427] GICv3: CPU13: found redistributor 601 region
> > > 0:0x00000000063a0000
> > > [ 0.565440] GICv3: CPU13: using allocated LPI pending table
> > > @0x0000002178e30000
> > > [ 0.565455] CPU13: Booted secondary processor 0x0000000601
> > > [0x410fd083]
> > > [ 0.597470] Detected PIPT I-cache on CPU14
> > > [ 0.597494] GICv3: CPU14: found redistributor 700 region
> > > 0:0x00000000063c0000
> > > [ 0.597507] GICv3: CPU14: using allocated LPI pending table
> > > @0x0000002178e40000
> > > [ 0.597527] CPU14: Booted secondary processor 0x0000000700
> > > [0x410fd083]
> > > [ 0.629523] Detected PIPT I-cache on CPU15
> > > [ 0.629543] GICv3: CPU15: found redistributor 701 region
> > > 0:0x00000000063e0000
> > > [ 0.629556] GICv3: CPU15: using allocated LPI pending table
> > > @0x0000002178e50000
> > > [ 0.629571] CPU15: Booted secondary processor 0x0000000701
> > > [0x410fd083]
> > > [ 0.629684] smp: Brought up 1 node, 16 CPUs
> > > [ 0.931457] SMP: Total of 16 processors activated.
> > > [ 0.934986] CPU features: detected: 32-bit EL0 Support
> > > [ 0.938858] CPU features: detected: CRC32 instructions
> > > [ 0.947732] CPU features: emulated: Privileged Access Never (PAN)
> > > using TTBR0_EL1 switching
> > > [ 0.954876] CPU: All CPU(s) started at EL2
> > > [ 0.957748] alternatives: patching kernel code
> > > [ 0.961954] devtmpfs: initialized
> > > [ 0.968138] random: get_random_u32 called from
> > > bucket_table_alloc.isra.22+0x88/0x1e0 with crng_init=0
> > > [ 0.976604] clocksource: jiffies: mask: 0xffffffff max_cycles:
> > > 0xffffffff, max_idle_ns: 7645041785100000 ns
> > > [ 0.985153] futex hash table entries: 4096 (order: 7, 524288
> > > bytes, linear)
> > > [ 0.991643] pinctrl core: initialized pinctrl subsystem
> > > [ 0.996213] thermal_sys: Registered thermal governor 'step_wise'
> > > [ 0.996473] DMI not present or invalid.
> > > [ 1.004023] NET: Registered protocol family 16
> > > [ 1.008239] DMA: preallocated 256 KiB pool for atomic allocations
> > > [ 1.013102] audit: initializing netlink subsys (disabled)
> > > [ 1.017340] audit: type=2000 audit(0.828:1): state=initialized
> > > audit_enabled=0 res=1
> > > [ 1.023873] cpuidle: using governor ladder
> > > [ 1.026734] cpuidle: using governor menu
> > > [ 1.029477] hw-breakpoint: found 6 breakpoint and 4 watchpoint
> > > registers.
> > > [ 1.035332] Serial: AMBA PL011 UART driver
> > > [ 1.039319] Machine: SolidRun LX2160A Clearfog CX
> > > [ 1.042751] SoC family: QorIQ LX2160A
> > > [ 1.045135] SoC ID: svr:0x87361010, Revision: 1.0
> > > [ 1.049775] 21c0000.serial: ttyAMA0 at MMIO 0x21c0000 (irq = 17,
> > > base_baud = 0) is a SBSA
> > > [ 1.056765] printk: console [ttyAMA0] enabled
> > > [ 1.062890] printk: bootconsole [pl11] disabled
> > > [ 1.069745] 21d0000.serial: ttyAMA1 at MMIO 0x21d0000 (irq = 18,
> > > base_baud = 0) is a SBSA
> > > [ 1.083284] fsl_mc_bus 80c000000.fsl-mc: MC firmware version: 10.18.0
> > > [ 1.091046] fsl_mc_dprc dprc.1: DMA mask not set
> > > [ 1.104098] HugeTLB registered 1.00 GiB page size, pre-allocated
> > > 0 pages
> > > [ 1.109500] HugeTLB registered 32.0 MiB page size, pre-allocated
> > > 0 pages
> > > [ 1.114906] HugeTLB registered 2.00 MiB page size, pre-allocated
> > > 0 pages
> > > [ 1.120298] HugeTLB registered 64.0 KiB page size, pre-allocated
> > > 0 pages
> > > [ 1.127238] cryptd: max_cpu_qlen set to 1000
> > > [ 1.132187] iommu: Default domain type: Translated (set via
> > > kernel command line)
> > > [ 1.138411] vgaarb: loaded
> > > [ 1.140045] SCSI subsystem initialized
> > > [ 1.142660] libata version 3.00 loaded.
> > > [ 1.142830] usbcore: registered new interface driver usbfs
> > > [ 1.147050] usbcore: registered new interface driver hub
> > > [ 1.151152] usbcore: registered new device driver usb
> > > [ 1.155269] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery
> > > not supported
> > > [ 1.161373] i2c i2c-0: IMX I2C adapter registered
> > > [ 1.164914] imx-i2c 2020000.i2c: can't get pinctrl, bus recovery
> > > not supported
> > > [ 1.170923] i2c i2c-1: IMX I2C adapter registered
> > > [ 1.174438] imx-i2c 2040000.i2c: can't get pinctrl, bus recovery
> > > not supported
> > > [ 1.180489] i2c i2c-2: IMX I2C adapter registered
> > > [ 1.184034] pps_core: LinuxPPS API ver. 1 registered
> > > [ 1.187711] pps_core: Software ver. 5.3.6 - Copyright 2005-2007
> > > Rodolfo Giometti <giometti@linux.it>
> > > [ 1.195563] PTP clock support registered
> > > [ 1.198926] clocksource: Switched to clocksource arch_sys_counter
> > > [ 1.409271] VFS: Disk quotas dquot_6.6.0
> > > [ 1.411929] VFS: Dquot-cache hash table entries: 512 (order 0,
> > > 4096 bytes)
> > > [ 1.423147] NET: Registered protocol family 2
> > > [ 1.426524] tcp_listen_portaddr_hash hash table entries: 4096
> > > (order: 6, 294912 bytes, linear)
> > > [ 1.434212] TCP established hash table entries: 65536 (order: 7,
> > > 524288 bytes, linear)
> > > [ 1.441038] TCP bind hash table entries: 65536 (order: 10,
> > > 4194304 bytes, linear)
> > > [ 1.452946] TCP: Hash tables configured (established 65536 bind 65536)
> > > [ 1.458362] UDP hash table entries: 4096 (order: 7, 655360 bytes,
> > > linear)
> > > [ 1.464637] UDP-Lite hash table entries: 4096 (order: 7, 655360
> > > bytes, linear)
> > > [ 1.471476] NET: Registered protocol family 1
> > > [ 1.474948] RPC: Registered named UNIX socket transport module.
> > > [ 1.479561] RPC: Registered udp transport module.
> > > [ 1.482958] RPC: Registered tcp transport module.
> > > [ 1.486348] RPC: Registered tcp NFSv4.1 backchannel transport module.
> > > [ 1.491485] PCI: CLS 0 bytes, default 64
> > > [ 1.495248] hw perfevents: enabled with armv8_cortex_a72 PMU
> > > driver, 7 counters available
> > > [ 1.502280] kvm: Limiting the IPA size due to kernel Virtual
> > > Address limit
> > > [ 1.507851] kvm [1]: IPA Size Limit: 43bits
> > > [ 1.511572] kvm [1]: vgic-v2@c0e0000
> > > [ 1.513851] kvm [1]: GIC system register CPU interface enabled
> > > [ 1.518687] kvm [1]: vgic interrupt IRQ1
> > > [ 1.521608] kvm [1]: Hyp mode initialized successfully
> > > [ 1.535818] workingset: timestamp_bits=46 max_order=21 bucket_order=0
> > > [ 1.549175] NFS: Registering the id_resolver key type
> > > [ 1.552967] Key type id_resolver registered
> > > [ 1.555844] Key type id_legacy registered
> > > [ 1.558661] fuse: init (API version 7.31)
> > > [ 1.561605] 9p: Installing v9fs 9p2000 file system support
> > > [ 1.566505] io scheduler mq-deadline registered
> > > [ 1.569734] io scheduler kyber registered
> > > [ 1.573894] layerscape-pcie-gen4 3600000.pcie: host bridge
> > > /soc/pcie@3600000 ranges:
> > > [ 1.580351] layerscape-pcie-gen4 3600000.pcie: MEM
> > > 0x9040000000..0x907fffffff -> 0x0040000000
> > > [ 1.588204] layerscape-pcie-gen4 3600000.pcie: PCI host bridge to
> > > bus 0000:00
> > > [ 1.594036] pci_bus 0000:00: root bus resource [bus 00-ff]
> > > [ 1.598216] pci_bus 0000:00: root bus resource [mem
> > > 0x9040000000-0x907fffffff] (bus address [0x40000000-0x7fffffff])
> > > [ 1.607459] pci 0000:00:00.0: [1957:8d90] type 01 class 0x060400
> > > [ 1.612198] pci 0000:00:00.0: enabling Extended Tags
> > > [ 1.615912] pci 0000:00:00.0: supports D1 D2
> > > [ 1.618869] pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot
> > > D3cold
> > > [ 1.624897] pci 0000:01:00.0: [1cc1:8201] type 00 class 0x010802
> > > [ 1.629666] pci 0000:01:00.0: reg 0x10: [mem
> > > 0x9040000000-0x9040003fff 64bit]
> > > [ 1.646977] pci 0000:00:00.0: up support 3 enabled 0
> > > [ 1.650628] pci 0000:00:00.0: dn support 2 enabled 0
> > > [ 1.654743] pci 0000:00:00.0: BAR 8: assigned [mem
> > > 0x9040000000-0x90400fffff]
> > > [ 1.660577] pci 0000:01:00.0: BAR 0: assigned [mem
> > > 0x9040000000-0x9040003fff 64bit]
> > > [ 1.666945] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
> > > [ 1.670859] pci 0000:00:00.0: bridge window [mem
> > > 0x9040000000-0x90400fffff]
> > > [ 1.676698] pci 0000:00:00.0: Max Payload Size set to 256/ 256
> > > (was 128), Max Read Rq 256
> > > [ 1.683858] pci 0000:01:00.0: Max Payload Size set to 256/ 256
> > > (was 128), Max Read Rq 256
> > > [ 1.691047] pcieport 0000:00:00.0: PCIe capabilities: 0x13
> > > [ 1.695230] pcieport 0000:00:00.0: init_service_irqs: -19
> > > [ 1.699429] layerscape-pcie-gen4 3800000.pcie: host bridge
> > > /soc/pcie@3800000 ranges:
> > > [ 1.705877] layerscape-pcie-gen4 3800000.pcie: MEM
> > > 0xa040000000..0xa07fffffff -> 0x0040000000
> > > [ 1.713713] layerscape-pcie-gen4 3800000.pcie: PCI host bridge to
> > > bus 0001:00
> > > [ 1.719544] pci_bus 0001:00: root bus resource [bus 00-ff]
> > > [ 1.723724] pci_bus 0001:00: root bus resource [mem
> > > 0xa040000000-0xa07fffffff] (bus address [0x40000000-0x7fffffff])
> > > [ 1.732950] pci 0001:00:00.0: [1957:8d90] type 01 class 0x060400
> > > [ 1.737694] pci 0001:00:00.0: enabling Extended Tags
> > > [ 1.741407] pci 0001:00:00.0: supports D1 D2
> > > [ 1.744371] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot
> > > D3cold
> > > [ 1.750511] pci 0001:01:00.0: [15b3:6750] type 00 class 0x020000
> > > [ 1.755600] pci 0001:01:00.0: reg 0x10: [mem
> > > 0xa040000000-0xa0400fffff 64bit]
> > > [ 1.761632] pci 0001:01:00.0: reg 0x18: [mem
> > > 0xa040800000-0xa040ffffff 64bit pref]
> > > [ 1.768286] pci 0001:01:00.0: reg 0x30: [mem
> > > 0xa041000000-0xa0410fffff pref]
> > > [ 1.787013] pci 0001:00:00.0: up support 3 enabled 0
> > > [ 1.790665] pci 0001:00:00.0: dn support 1 enabled 0
> > > [ 1.794787] pci 0001:00:00.0: BAR 9: assigned [mem
> > > 0xa040000000-0xa0407fffff 64bit pref]
> > > [ 1.801572] pci 0001:00:00.0: BAR 8: assigned [mem
> > > 0xa040800000-0xa0409fffff]
> > > [ 1.807404] pci 0001:01:00.0: BAR 2: assigned [mem
> > > 0xa040000000-0xa0407fffff 64bit pref]
> > > [ 1.814316] pci 0001:01:00.0: BAR 0: assigned [mem
> > > 0xa040800000-0xa0408fffff 64bit]
> > > [ 1.820793] pci 0001:01:00.0: BAR 6: assigned [mem
> > > 0xa040900000-0xa0409fffff pref]
> > > [ 1.827056] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
> > > [ 1.830977] pci 0001:00:00.0: bridge window [mem
> > > 0xa040800000-0xa0409fffff]
> > > [ 1.836806] pci 0001:00:00.0: bridge window [mem
> > > 0xa040000000-0xa0407fffff 64bit pref]
> > > [ 1.843601] pci 0001:00:00.0: Max Payload Size set to 256/ 256
> > > (was 128), Max Read Rq 256
> > > [ 1.850903] pci 0001:01:00.0: Max Payload Size set to 256/ 256
> > > (was 128), Max Read Rq 256
> > > [ 1.858079] pcieport 0001:00:00.0: PCIe capabilities: 0x13
> > > [ 1.862260] pcieport 0001:00:00.0: init_service_irqs: -19
> > > [ 1.867322] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
> > > [ 1.874084] arm-smmu 5000000.iommu: probing hardware configuration...
> > > [ 1.879225] arm-smmu 5000000.iommu: SMMUv2 with:
> > > [ 1.882529] arm-smmu 5000000.iommu: stage 1 translation
> > > [ 1.886534] arm-smmu 5000000.iommu: stage 2 translation
> > > [ 1.890539] arm-smmu 5000000.iommu: nested translation
> > > [ 1.894457] arm-smmu 5000000.iommu: coherent table walk
> > > [ 1.898461] arm-smmu 5000000.iommu: (IDR0.CTTW overridden by
> > > FW configuration)
> > > [ 1.904464] arm-smmu 5000000.iommu: stream matching with 128
> > > register groups
> > > [ 1.910294] arm-smmu 5000000.iommu: 64 context banks (0
> > > stage-2 only)
> > > [ 1.915519] arm-smmu 5000000.iommu: Supported page sizes:
> > > 0x61311000
> > > [ 1.920653] arm-smmu 5000000.iommu: Stage-1: 48-bit VA ->
> > > 48-bit IPA
> > > [ 1.925786] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA ->
> > > 48-bit PA
> > > [ 1.946137] loop: module loaded
> > > [ 1.948871] nvme nvme0: pci function 0000:01:00.0
> > > [ 1.952710] ahci-qoriq 3200000.sata: 3200000.sata supply ahci not
> > > found, using dummy regulator
> > > [ 1.960072] ahci-qoriq 3200000.sata: 3200000.sata supply phy not
> > > found, using dummy regulator
> > > [ 1.967335] ahci-qoriq 3200000.sata: 3200000.sata supply target
> > > not found, using dummy regulator
> > > [ 1.974957] ahci-qoriq 3200000.sata: AHCI 0001.0301 32 slots 1
> > > ports 6 Gbps 0x1 impl platform mode
> > > [ 1.982613] ahci-qoriq 3200000.sata: flags: 64bit ncq sntf pm clo
> > > only pmp fbs pio slum part ccc sds apst
> > > [ 1.991486] scsi host0: ahci-qoriq
> > > [ 1.993859] ata1: SATA max UDMA/133 mmio [mem
> > > 0x03200000-0x0320ffff] port 0x100 irq 24
> > > [ 2.000561] ahci-qoriq 3210000.sata: 3210000.sata supply ahci not
> > > found, using dummy regulator
> > > [ 2.007916] ahci-qoriq 3210000.sata: 3210000.sata supply phy not
> > > found, using dummy regulator
> > > [ 2.015194] ahci-qoriq 3210000.sata: 3210000.sata supply target
> > > not found, using dummy regulator
> > > [ 2.022788] ahci-qoriq 3210000.sata: AHCI 0001.0301 32 slots 1
> > > ports 6 Gbps 0x1 impl platform mode
> > > [ 2.030443] ahci-qoriq 3210000.sata: flags: 64bit ncq sntf pm clo
> > > only pmp fbs pio slum part ccc sds apst
> > > [ 2.039256] scsi host1: ahci-qoriq
> > > [ 2.041507] ata2: SATA max UDMA/133 mmio [mem
> > > 0x03210000-0x0321ffff] port 0x100 irq 25
> > > [ 2.048196] ahci-qoriq 3220000.sata: 3220000.sata supply ahci not
> > > found, using dummy regulator
> > > [ 2.055550] ahci-qoriq 3220000.sata: 3220000.sata supply phy not
> > > found, using dummy regulator
> > > [ 2.062811] ahci-qoriq 3220000.sata: 3220000.sata supply target
> > > not found, using dummy regulator
> > > [ 2.070378] ahci-qoriq 3220000.sata: AHCI 0001.0301 32 slots 1
> > > ports 6 Gbps 0x1 impl platform mode
> > > [ 2.078032] ahci-qoriq 3220000.sata: flags: 64bit ncq sntf pm clo
> > > only pmp fbs pio slum part ccc sds apst
> > > [ 2.084600] nvme nvme0: 15/0/0 default/read/poll queues
> > > [ 2.086837] scsi host2: ahci-qoriq
> > > [ 2.092574] ata3: SATA max UDMA/133 mmio [mem
> > > 0x03220000-0x0322ffff] port 0x100 irq 26
> > > [ 2.092925] nvme0n1: p1 p2
> > > [ 2.099262] ahci-qoriq 3230000.sata: 3230000.sata supply ahci not
> > > found, using dummy regulator
> > > [ 2.108028] ahci-qoriq 3230000.sata: 3230000.sata supply phy not
> > > found, using dummy regulator
> > > [ 2.115290] ahci-qoriq 3230000.sata: 3230000.sata supply target
> > > not found, using dummy regulator
> > > [ 2.122864] ahci-qoriq 3230000.sata: AHCI 0001.0301 32 slots 1
> > > ports 6 Gbps 0x1 impl platform mode
> > > [ 2.130518] ahci-qoriq 3230000.sata: flags: 64bit ncq sntf pm clo
> > > only pmp fbs pio slum part ccc sds apst
> > > [ 2.139348] scsi host3: ahci-qoriq
> > > [ 2.141598] ata4: SATA max UDMA/133 mmio [mem
> > > 0x03230000-0x0323ffff] port 0x100 irq 27
> > > [ 2.149539] libphy: Fixed MDIO Bus: probed
> > > [ 2.152802] libphy: Freescale XGMAC MDIO Bus: probed
> > > [ 2.156799] Qualcomm Atheros AR8035 8b96000:01: probe: irq=-1
> > > [ 2.161245] Qualcomm Atheros AR8035 8b96000:01: probe: irq=-1
> > > [ 2.165963] libphy: Freescale XGMAC MDIO Bus: probed
> > > [ 2.170081] dwc3 3100000.usb: Failed to get clk 'ref': -2
> > > [ 2.174468] dwc3 3110000.usb: Failed to get clk 'ref': -2
> > > [ 2.179050] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
> > > [ 2.184274] ehci-platform: EHCI generic platform driver
> > > [ 2.188257] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
> > > [ 2.193140] ohci-platform: OHCI generic platform driver
> > > [ 2.197268] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
> > > [ 2.201470] xhci-hcd xhci-hcd.0.auto: new USB bus registered,
> > > assigned bus number 1
> > > [ 2.207946] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci
> > > version 0x100 quirks 0x0000000002010010
> > > [ 2.216064] xhci-hcd xhci-hcd.0.auto: irq 22, io mem 0x03100000
> > > [ 2.221416] hub 1-0:1.0: USB hub found
> > > [ 2.223894] hub 1-0:1.0: 1 port detected
> > > [ 2.226762] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
> > > [ 2.230951] xhci-hcd xhci-hcd.0.auto: new USB bus registered,
> > > assigned bus number 2
> > > [ 2.237305] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
> > > [ 2.242572] usb usb2: We don't know the algorithms for LPM for
> > > this host, disabling LPM.
> > > [ 2.249744] hub 2-0:1.0: USB hub found
> > > [ 2.252209] hub 2-0:1.0: 1 port detected
> > > [ 2.255118] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
> > > [ 2.259309] xhci-hcd xhci-hcd.1.auto: new USB bus registered,
> > > assigned bus number 3
> > > [ 2.265760] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci
> > > version 0x100 quirks 0x0000000002010010
> > > [ 2.273872] xhci-hcd xhci-hcd.1.auto: irq 23, io mem 0x03110000
> > > [ 2.279084] hub 3-0:1.0: USB hub found
> > > [ 2.281538] hub 3-0:1.0: 1 port detected
> > > [ 2.284380] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
> > > [ 2.288571] xhci-hcd xhci-hcd.1.auto: new USB bus registered,
> > > assigned bus number 4
> > > [ 2.294930] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
> > > [ 2.300190] usb usb4: We don't know the algorithms for LPM for
> > > this host, disabling LPM.
> > > [ 2.307363] hub 4-0:1.0: USB hub found
> > > [ 2.309817] hub 4-0:1.0: 1 port detected
> > > [ 2.312750] usbcore: registered new interface driver usb-storage
> > > [ 2.317173] ata1: SATA link down (SStatus 0 SControl 300)
> > > [ 2.317696] mousedev: PS/2 mouse device common for all mice
> > > [ 2.331955] rtc-pcf2127-i2c 2-0051: registered as rtc0
> > > [ 2.335876] i2c /dev entries driver
> > > [ 2.339327] i2c i2c-0: Added multiplexed i2c bus 3
> > > [ 2.343067] i2c i2c-0: Added multiplexed i2c bus 4
> > > [ 2.346783] i2c i2c-0: Added multiplexed i2c bus 5
> > > [ 2.350507] i2c i2c-0: Added multiplexed i2c bus 6
> > > [ 2.354164] i2c i2c-0: Added multiplexed i2c bus 7
> > > [ 2.357821] i2c i2c-0: Added multiplexed i2c bus 8
> > > [ 2.361159] ata2: SATA link down (SStatus 0 SControl 300)
> > > [ 2.361480] i2c i2c-0: Added multiplexed i2c bus 9
> > > [ 2.369047] i2c i2c-0: Added multiplexed i2c bus 10
> > > [ 2.372627] pca954x 0-0077: registered 8 multiplexed busses for
> > > I2C mux pca9547
> > > [ 2.378783] IR NEC protocol handler initialized
> > > [ 2.382010] IR RC5(x/sz) protocol handler initialized
> > > [ 2.385755] IR RC6 protocol handler initialized
> > > [ 2.388977] IR JVC protocol handler initialized
> > > [ 2.392200] IR Sony protocol handler initialized
> > > [ 2.395513] IR SANYO protocol handler initialized
> > > [ 2.398903] IR Sharp protocol handler initialized
> > > [ 2.402300] IR MCE Keyboard/mouse protocol handler initialized
> > > [ 2.406827] IR XMP protocol handler initialized
> > > [ 2.413367] amc6821 4-0018: Error reading configuration register,
> > > aborting.
> > > [ 2.417180] ata3: SATA link down (SStatus 0 SControl 300)
> > > [ 2.419034] amc6821: probe of 4-0018 failed with error -5
> > > [ 2.427436] sdhci: Secure Digital Host Controller Interface driver
> > > [ 2.432314] sdhci: Copyright(c) Pierre Ossman
> > > [ 2.435384] sdhci-pltfm: SDHCI platform and OF driver helper
> > > [ 2.461157] ata4: SATA link down (SStatus 0 SControl 300)
> > > [ 2.465487] mmc0: SDHCI controller on 2140000.esdhc
> > > [2140000.esdhc] using ADMA 64-bit
> > > [ 2.494954] mmc1: SDHCI controller on 2150000.esdhc
> > > [2150000.esdhc] using ADMA 64-bit
> > > [ 2.502071] ledtrig-cpu: registered to indicate activity on CPUs
> > > [ 2.507175] caam 8000000.crypto: device ID = 0x0a1a020000000000
> > > (Era 10)
> > > [ 2.508538] mmc0: new high speed SDHC card at address aaaa
> > > [ 2.512572] caam 8000000.crypto: job rings = 3, qi = 1
> > > [ 2.521006] mmcblk0: mmc0:aaaa SU04G 3.69 GiB (ro)
> > > [ 2.525840] caam algorithms registered in /proc/crypto
> > > [ 2.532365] caam 8000000.crypto: caam pkc algorithms registered
> > > in /proc/crypto
> > > [ 2.539400] caam_jr 8010000.jr: registering rng-caam
> > > [ 2.543736] usbcore: registered new interface driver usbhid
> > > [ 2.548007] usbhid: USB HID core driver
> > > [ 2.551148] NET: Registered protocol family 10
> > > [ 2.554963] Segment Routing with IPv6
> > > [ 2.557343] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
> > > [ 2.562313] NET: Registered protocol family 17
> > > [ 2.565629] 9pnet: Installing 9P2000 support
> > > [ 2.568641] Key type dns_resolver registered
> > > [ 2.571820] registered taskstats version 1
> > > [ 2.578646] fsl_mc_dprc dprc.1: Adding to iommu group 0
> > > [ 2.584473] mmc1: new HS400 MMC card at address 0001
> > > [ 2.592566] mmcblk1: mmc1:0001 DF4064 58.2 GiB
> > > [ 2.595945] mmcblk1boot0: mmc1:0001 DF4064 partition 1 4.00 MiB
> > > [ 2.600717] mmcblk1boot1: mmc1:0001 DF4064 partition 2 4.00 MiB
> > > [ 2.605471] mmcblk1rpmb: mmc1:0001 DF4064 partition 3 4.00 MiB,
> > > chardev (246:0)
> > > [ 2.612749] mmcblk1: p1 p2
> > > [ 2.622945] usb 3-1: new high-speed USB device number 2 using xhci-hcd
> > > [ 2.642000] fsl_dpaa2_eth dpni.0: Adding to iommu group 0
> > > [ 2.646254] fsl_mc_dprc dprc.1: No more resources of type dpmcp left
> > > [ 2.651688] fsl_mc_allocator dpbp.1: Adding to iommu group 0
> > > [ 2.656161] fsl_mc_allocator dpbp.0: Adding to iommu group 0
> > > [ 2.662117] fsl_mc_allocator dpmcp.35: Adding to iommu group 0
> > > [ 2.667765] fsl_mc_allocator dpmcp.34: Adding to iommu group 0
> > > [ 2.673422] fsl_mc_allocator dpmcp.33: Adding to iommu group 0
> > > [ 2.679071] fsl_mc_allocator dpmcp.32: Adding to iommu group 0
> > > [ 2.684267] hub 3-1:1.0: USB hub found
> > > [ 2.684727] fsl_mc_allocator dpmcp.31: Adding to iommu group 0
> > > [ 2.686736] hub 3-1:1.0: 4 ports detected
> > > [ 2.692343] fsl_mc_allocator dpmcp.30: Adding to iommu group 0
> > > [ 2.699627] fsl_mc_allocator dpmcp.29: Adding to iommu group 0
> > > [ 2.705265] fsl_mc_allocator dpmcp.28: Adding to iommu group 0
> > > [ 2.710952] fsl_mc_allocator dpmcp.27: Adding to iommu group 0
> > > [ 2.716596] fsl_mc_allocator dpmcp.26: Adding to iommu group 0
> > > [ 2.722243] fsl_mc_allocator dpmcp.25: Adding to iommu group 0
> > > [ 2.727897] fsl_mc_allocator dpmcp.24: Adding to iommu group 0
> > > [ 2.733550] fsl_mc_allocator dpmcp.23: Adding to iommu group 0
> > > [ 2.739198] fsl_mc_allocator dpmcp.22: Adding to iommu group 0
> > > [ 2.744853] fsl_mc_allocator dpmcp.21: Adding to iommu group 0
> > > [ 2.750495] fsl_mc_allocator dpmcp.20: Adding to iommu group 0
> > > [ 2.756161] fsl_mc_allocator dpmcp.19: Adding to iommu group 0
> > > [ 2.761803] fsl_mc_allocator dpmcp.18: Adding to iommu group 0
> > > [ 2.767473] fsl_mc_allocator dpmcp.17: Adding to iommu group 0
> > > [ 2.773117] fsl_mc_allocator dpmcp.16: Adding to iommu group 0
> > > [ 2.778768] fsl_mc_allocator dpmcp.15: Adding to iommu group 0
> > > [ 2.782959] usb 4-1: new SuperSpeed Gen 1 USB device number 2
> > > using xhci-hcd
> > > [ 2.784414] fsl_mc_allocator dpmcp.14: Adding to iommu group 0
> > > [ 2.794669] fsl_mc_allocator dpmcp.13: Adding to iommu group 0
> > > [ 2.800309] fsl_mc_allocator dpmcp.12: Adding to iommu group 0
> > > [ 2.805969] fsl_mc_allocator dpmcp.11: Adding to iommu group 0
> > > [ 2.811625] fsl_mc_allocator dpmcp.10: Adding to iommu group 0
> > > [ 2.817271] fsl_mc_allocator dpmcp.9: Adding to iommu group 0
> > > [ 2.822845] fsl_mc_allocator dpmcp.8: Adding to iommu group 0
> > > [ 2.828243] hub 4-1:1.0: USB hub found
> > > [ 2.828420] fsl_mc_allocator dpmcp.7: Adding to iommu group 0
> > > [ 2.830710] hub 4-1:1.0: 4 ports detected
> > > [ 2.836276] fsl_mc_allocator dpmcp.6: Adding to iommu group 0
> > > [ 2.843415] fsl_mc_allocator dpmcp.5: Adding to iommu group 0
> > > [ 2.848975] fsl_mc_allocator dpmcp.4: Adding to iommu group 0
> > > [ 2.851038] random: fast init done
> > > [ 2.854534] fsl_mc_allocator dpmcp.3: Adding to iommu group 0
> > > [ 2.861060] fsl_mc_allocator dpmcp.2: Adding to iommu group 0
> > > [ 2.866622] fsl_mc_allocator dpmcp.1: Adding to iommu group 0
> > > [ 2.874308] fsl_mc_dpio dpio.15: Adding to iommu group 0
> > > [ 2.882022] fsl_mc_dpio dpio.15: probed
> > > [ 2.888261] fsl_mc_dpio dpio.14: Adding to iommu group 0
> > > [ 2.895912] fsl_mc_dpio dpio.14: probed
> > > [ 2.902061] fsl_mc_dpio dpio.13: Adding to iommu group 0
> > > [ 2.909710] fsl_mc_dpio dpio.13: probed
> > > [ 2.915939] fsl_mc_dpio dpio.12: Adding to iommu group 0
> > > [ 2.923591] fsl_mc_dpio dpio.12: probed
> > > [ 2.929752] fsl_mc_dpio dpio.11: Adding to iommu group 0
> > > [ 2.937396] fsl_mc_dpio dpio.11: probed
> > > [ 2.943628] fsl_mc_dpio dpio.10: Adding to iommu group 0
> > > [ 2.951283] fsl_mc_dpio dpio.10: probed
> > > [ 2.957446] fsl_mc_dpio dpio.9: Adding to iommu group 0
> > > [ 2.965012] fsl_mc_dpio dpio.9: probed
> > > [ 2.971167] fsl_mc_dpio dpio.8: Adding to iommu group 0
> > > [ 2.978776] fsl_mc_dpio dpio.8: probed
> > > [ 2.984923] fsl_mc_dpio dpio.7: Adding to iommu group 0
> > > [ 2.992537] fsl_mc_dpio dpio.7: probed
> > > [ 2.998684] fsl_mc_dpio dpio.6: Adding to iommu group 0
> > > [ 3.006299] fsl_mc_dpio dpio.6: probed
> > > [ 3.012440] fsl_mc_dpio dpio.5: Adding to iommu group 0
> > > [ 3.020064] fsl_mc_dpio dpio.5: probed
> > > [ 3.026190] fsl_mc_dpio dpio.4: Adding to iommu group 0
> > > [ 3.033754] fsl_mc_dpio dpio.4: probed
> > > [ 3.038937] usb 3-1.3: new high-speed USB device number 3 using
> > > xhci-hcd
> > > [ 3.039844] fsl_mc_dpio dpio.3: Adding to iommu group 0
> > > [ 3.051890] fsl_mc_dpio dpio.3: probed
> > > [ 3.058009] fsl_mc_dpio dpio.2: Adding to iommu group 0
> > > [ 3.065609] fsl_mc_dpio dpio.2: probed
> > > [ 3.071763] fsl_mc_dpio dpio.1: Adding to iommu group 0
> > > [ 3.079384] fsl_mc_dpio dpio.1: probed
> > > [ 3.085521] fsl_mc_dpio dpio.0: Adding to iommu group 0
> > > [ 3.093136] fsl_mc_dpio dpio.0: probed
> > > [ 3.096201] fsl_mc_allocator dpcon.31: Adding to iommu group 0
> > > [ 3.100196] hub 3-1.3:1.0: USB hub found
> > > [ 3.100860] fsl_mc_allocator dpcon.30: Adding to iommu group 0
> > > [ 3.103374] hub 3-1.3:1.0: 4 ports detected
> > > [ 3.107983] fsl_mc_allocator dpcon.29: Adding to iommu group 0
> > > [ 3.115381] fsl_mc_allocator dpcon.28: Adding to iommu group 0
> > > [ 3.120030] fsl_mc_allocator dpcon.27: Adding to iommu group 0
> > > [ 3.124682] fsl_mc_allocator dpcon.26: Adding to iommu group 0
> > > [ 3.129333] fsl_mc_allocator dpcon.25: Adding to iommu group 0
> > > [ 3.133987] fsl_mc_allocator dpcon.24: Adding to iommu group 0
> > > [ 3.138642] fsl_mc_allocator dpcon.23: Adding to iommu group 0
> > > [ 3.143294] fsl_mc_allocator dpcon.22: Adding to iommu group 0
> > > [ 3.147946] fsl_mc_allocator dpcon.21: Adding to iommu group 0
> > > [ 3.152597] fsl_mc_allocator dpcon.20: Adding to iommu group 0
> > > [ 3.157250] fsl_mc_allocator dpcon.19: Adding to iommu group 0
> > > [ 3.161903] fsl_mc_allocator dpcon.18: Adding to iommu group 0
> > > [ 3.166559] fsl_mc_allocator dpcon.17: Adding to iommu group 0
> > > [ 3.171217] fsl_mc_allocator dpcon.16: Adding to iommu group 0
> > > [ 3.175871] fsl_mc_allocator dpcon.15: Adding to iommu group 0
> > > [ 3.180533] fsl_mc_allocator dpcon.14: Adding to iommu group 0
> > > [ 3.185188] fsl_mc_allocator dpcon.13: Adding to iommu group 0
> > > [ 3.189844] fsl_mc_allocator dpcon.12: Adding to iommu group 0
> > > [ 3.194499] fsl_mc_allocator dpcon.11: Adding to iommu group 0
> > > [ 3.199153] fsl_mc_allocator dpcon.10: Adding to iommu group 0
> > > [ 3.203810] fsl_mc_allocator dpcon.9: Adding to iommu group 0
> > > [ 3.208385] fsl_mc_allocator dpcon.8: Adding to iommu group 0
> > > [ 3.212956] fsl_mc_allocator dpcon.7: Adding to iommu group 0
> > > [ 3.217526] fsl_mc_allocator dpcon.6: Adding to iommu group 0
> > > [ 3.222096] fsl_mc_allocator dpcon.5: Adding to iommu group 0
> > > [ 3.226667] fsl_mc_allocator dpcon.4: Adding to iommu group 0
> > > [ 3.231237] fsl_mc_allocator dpcon.3: Adding to iommu group 0
> > > [ 3.235812] fsl_mc_allocator dpcon.2: Adding to iommu group 0
> > > [ 3.240383] fsl_mc_allocator dpcon.1: Adding to iommu group 0
> > > [ 3.244955] fsl_mc_allocator dpcon.0: Adding to iommu group 0
> > > [ 3.252565] fsl_mc_dprc dprc.1: DPRC device bound to driver
> > > [ 3.257032] libphy: SFP I2C Bus: probed
> > > [ 3.259658] sfp sfp-0: Host maximum power 2.0W
> > > [ 3.262929] sfp sfp-0: No tx_disable pin: SFP modules will always
> > > be emitting.
> > > [ 3.269061] libphy: SFP I2C Bus: probed
> > > [ 3.271642] sfp sfp-1: Host maximum power 2.0W
> > > [ 3.274884] sfp sfp-1: No tx_disable pin: SFP modules will always
> > > be emitting.
> > > [ 3.280979] libphy: SFP I2C Bus: probed
> > > [ 3.283559] sfp sfp-2: Host maximum power 2.0W
> > > [ 3.286819] sfp sfp-2: No tx_disable pin: SFP modules will always
> > > be emitting.
> > > [ 3.292948] libphy: SFP I2C Bus: probed
> > > [ 3.295529] sfp sfp-3: Host maximum power 2.0W
> > > [ 3.298768] sfp sfp-3: No tx_disable pin: SFP modules will always
> > > be emitting.
> > > [ 3.456609] fsl_dpaa2_eth dpni.0 (unnamed net_device)
> > > (uninitialized): PHY [8b96000:01] driver [Qualcomm Atheros AR8035]
> > > (irq=POLL)
> > > [ 3.467153] fsl_dpaa2_eth dpni.0 (unnamed net_device)
> > > (uninitialized): phy: setting supported 000,00000200,000062ea
> > > advertising 000,00000200,000062ea
> > > [ 3.468341] fsl_dpaa2_eth dpni.0: Probed interface eth0
> > > [ 3.472672] input: gpio-keys as
> > > /devices/platform/gpio-keys/input/input0
> > > [ 3.479780] rtc-pcf2127-i2c 2-0051: setting system clock to
> > > 2020-02-28T09:56:18 UTC (1582883778)
> > > [ 3.490224] EXT4-fs (nvme0n1p2): mounted filesystem with ordered
> > > data mode. Opts: (null)
> > > [ 3.497082] VFS: Mounted root (ext4 filesystem) readonly on
> > > device 259:2.
> > > [ 3.503193] devtmpfs: mounted
> > > [ 3.505079] Freeing unused kernel memory: 960K
> > > [ 3.534993] Run /sbin/init as init process
> > >
> > > When asking for more network interfaces, more "Adding to iommu group"
> > > messages get spat out:
> > >
> > > [ 446.040825] fsl_dpaa2_eth dpni.1: Adding to iommu group 0
> > > [ 446.201254] libphy: Freescale XGMAC MDIO Bus: probed
> > > [ 446.206552] fsl_dpaa2_eth dpni.1: Probed interface eth1
> > > [ 446.210715] fsl_mc_allocator dpbp.2: Adding to iommu group 0
> > > [ 446.216838] fsl_mc_allocator dpmcp.36: Adding to iommu group 0
> > > [ 446.224808] fsl_mc_allocator dpcon.47: Adding to iommu group 0
> > > [ 446.229935] fsl_mc_allocator dpcon.46: Adding to iommu group 0
> > > [ 446.234685] fsl_mc_allocator dpcon.45: Adding to iommu group 0
> > > [ 446.239431] fsl_mc_allocator dpcon.44: Adding to iommu group 0
> > > [ 446.244179] fsl_mc_allocator dpcon.43: Adding to iommu group 0
> > > [ 446.251725] fsl_mc_allocator dpcon.42: Adding to iommu group 0
> > > [ 446.258952] fsl_mc_allocator dpcon.41: Adding to iommu group 0
> > > [ 446.263666] fsl_mc_allocator dpcon.40: Adding to iommu group 0
> > > [ 446.268377] fsl_mc_allocator dpcon.39: Adding to iommu group 0
> > > [ 446.273086] fsl_mc_allocator dpcon.38: Adding to iommu group 0
> > > [ 446.277814] fsl_mc_allocator dpcon.37: Adding to iommu group 0
> > > [ 446.282517] fsl_mc_allocator dpcon.36: Adding to iommu group 0
> > > [ 446.287228] fsl_mc_allocator dpcon.35: Adding to iommu group 0
> > > [ 446.291935] fsl_mc_allocator dpcon.34: Adding to iommu group 0
> > > [ 446.296641] fsl_mc_allocator dpcon.33: Adding to iommu group 0
> > > [ 446.301354] fsl_mc_allocator dpcon.32: Adding to iommu group 0
> > > [ 446.893939] fsl_dpaa2_eth dpni.2: Adding to iommu group 0
> > > [ 447.052868] libphy: Freescale XGMAC MDIO Bus: probed
> > > [ 447.058223] fsl_dpaa2_eth dpni.2: Probed interface eth2
> > > [ 447.062425] fsl_mc_allocator dpbp.3: Adding to iommu group 0
> > > [ 447.068813] fsl_mc_allocator dpmcp.37: Adding to iommu group 0
> > > [ 447.074280] fsl_mc_allocator dpcon.63: Adding to iommu group 0
> > > [ 447.078995] fsl_mc_allocator dpcon.62: Adding to iommu group 0
> > > [ 447.088690] fsl_mc_allocator dpcon.61: Adding to iommu group 0
> > > [ 447.093639] fsl_mc_allocator dpcon.60: Adding to iommu group 0
> > > [ 447.098369] fsl_mc_allocator dpcon.59: Adding to iommu group 0
> > > [ 447.103089] fsl_mc_allocator dpcon.58: Adding to iommu group 0
> > > [ 447.107811] fsl_mc_allocator dpcon.57: Adding to iommu group 0
> > > [ 447.112525] fsl_mc_allocator dpcon.56: Adding to iommu group 0
> > > [ 447.117244] fsl_mc_allocator dpcon.55: Adding to iommu group 0
> > > [ 447.121962] fsl_mc_allocator dpcon.54: Adding to iommu group 0
> > > [ 447.126680] fsl_mc_allocator dpcon.53: Adding to iommu group 0
> > > [ 447.131392] fsl_mc_allocator dpcon.52: Adding to iommu group 0
> > > [ 447.136107] fsl_mc_allocator dpcon.51: Adding to iommu group 0
> > > [ 447.140820] fsl_mc_allocator dpcon.50: Adding to iommu group 0
> > > [ 447.145535] fsl_mc_allocator dpcon.49: Adding to iommu group 0
> > > [ 447.150249] fsl_mc_allocator dpcon.48: Adding to iommu group 0
> > > [ 447.710694] fsl_dpaa2_eth dpni.3: Adding to iommu group 0
> > > [ 447.888120] libphy: Freescale XGMAC MDIO Bus: probed
> > > [ 447.893479] fsl_dpaa2_eth dpni.3: Probed interface eth3
> > > [ 447.897740] fsl_mc_allocator dpbp.4: Adding to iommu group 0
> > > [ 447.904488] fsl_mc_allocator dpmcp.38: Adding to iommu group 0
> > > [ 447.909994] fsl_mc_allocator dpcon.79: Adding to iommu group 0
> > > [ 447.914717] fsl_mc_allocator dpcon.78: Adding to iommu group 0
> > > [ 447.919852] fsl_mc_allocator dpcon.77: Adding to iommu group 0
> > > [ 447.924720] fsl_mc_allocator dpcon.76: Adding to iommu group 0
> > > [ 447.931979] fsl_mc_allocator dpcon.75: Adding to iommu group 0
> > > [ 447.939172] fsl_mc_allocator dpcon.74: Adding to iommu group 0
> > > [ 447.943886] fsl_mc_allocator dpcon.73: Adding to iommu group 0
> > > [ 447.948604] fsl_mc_allocator dpcon.72: Adding to iommu group 0
> > > [ 447.953319] fsl_mc_allocator dpcon.71: Adding to iommu group 0
> > > [ 447.958035] fsl_mc_allocator dpcon.70: Adding to iommu group 0
> > > [ 447.965445] fsl_mc_allocator dpcon.69: Adding to iommu group 0
> > > [ 447.972653] fsl_mc_allocator dpcon.68: Adding to iommu group 0
> > > [ 447.977376] fsl_mc_allocator dpcon.67: Adding to iommu group 0
> > > [ 447.982097] fsl_mc_allocator dpcon.66: Adding to iommu group 0
> > > [ 447.986816] fsl_mc_allocator dpcon.65: Adding to iommu group 0
> > > [ 447.991532] fsl_mc_allocator dpcon.64: Adding to iommu group 0
> > > [ 448.737198] fsl_dpaa2_eth dpni.4: Adding to iommu group 0
> > > [ 448.894480] libphy: Freescale XGMAC MDIO Bus: probed
> > > [ 448.899785] fsl_dpaa2_eth dpni.4: Probed interface eth4
> > > [ 448.904077] fsl_mc_allocator dpbp.5: Adding to iommu group 0
> > > [ 448.909817] fsl_mc_allocator dpmcp.39: Adding to iommu group 0
> > > [ 448.915340] fsl_mc_allocator dpcon.95: Adding to iommu group 0
> > > [ 448.920068] fsl_mc_allocator dpcon.94: Adding to iommu group 0
> > > [ 448.924789] fsl_mc_allocator dpcon.93: Adding to iommu group 0
> > > [ 448.929689] fsl_mc_allocator dpcon.92: Adding to iommu group 0
> > > [ 448.934436] fsl_mc_allocator dpcon.91: Adding to iommu group 0
> > > [ 448.939159] fsl_mc_allocator dpcon.90: Adding to iommu group 0
> > > [ 448.943882] fsl_mc_allocator dpcon.89: Adding to iommu group 0
> > > [ 448.948607] fsl_mc_allocator dpcon.88: Adding to iommu group 0
> > > [ 448.953327] fsl_mc_allocator dpcon.87: Adding to iommu group 0
> > > [ 448.958050] fsl_mc_allocator dpcon.86: Adding to iommu group 0
> > > [ 448.962771] fsl_mc_allocator dpcon.85: Adding to iommu group 0
> > > [ 448.967499] fsl_mc_allocator dpcon.84: Adding to iommu group 0
> > > [ 448.972219] fsl_mc_allocator dpcon.83: Adding to iommu group 0
> > > [ 448.976941] fsl_mc_allocator dpcon.82: Adding to iommu group 0
> > > [ 448.981669] fsl_mc_allocator dpcon.81: Adding to iommu group 0
> > > [ 448.986391] fsl_mc_allocator dpcon.80: Adding to iommu group 0
> > >
> > > # dmesg |grep 'Adding to iommu' | wc -l
> > > 164
> > > # dmesg |grep -v 'Adding to iommu' | wc -l
> > > 551
> > >
> > > So, 23% of the kernel messages on this platform are "Adding to iommu",
> > > which is excessive.
> >
> > Indeed, however I would note that on most platforms bringing up a
> > network interface involves hot-adding 0 devices, so hot-adding 19
> > devices as full-blown DMA masters is arguably the root of "excessive"
> > already. Per the concern I initially raised, each of those messages
> > represents a whole bunch of internal allocation and bookkeeping going
> > on, which if it isn't necessary would be far better avoided altogether,
> > than simply done more quietly.
> >
> > Laurentiu, I guess at the moment the nature of the of_dma_configure()
> > integration means we end up treating all DPAA2 objects identically, but
> > do you think we have scope to be a bit cleverer in that regard?
> > Presumably not every type of object that shows up on the fsl_mc bus is
> > really an independent DMA master, so if we could skip doing the full
> > DMA/IOMMU/MSI setup for the ones that don't need it, it would work out
> > nicer all round. In fact your .dma_configure proposal (which I'll try to
> > take a proper look at next week) couldn't have come at a better time for
> > that argument :)
> >
>
> Just FYI, I've tried Robin's suggestion and things greatly improved [1], so
> I think we can leave the iommu group messages alone.
>
> [1]
> # dmesg |grep 'Adding to iommu' | wc -l
> 7
> # dmesg |grep -v 'Adding to iommu' | wc -l
> 512
Please can you send me your patches for this.
Thanks.
--
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up
According to speedtest.net: 11.9Mbps down 500kbps up
_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH] iommu: silence iommu group prints
2020-03-03 15:49 ` Russell King - ARM Linux admin
@ 2020-03-03 15:55 ` Laurentiu Tudor
2020-03-03 22:17 ` Russell King - ARM Linux admin
0 siblings, 1 reply; 24+ messages in thread
From: Laurentiu Tudor @ 2020-03-03 15:55 UTC (permalink / raw)
To: Russell King - ARM Linux admin
Cc: Diana Madalina Craciun, iommu, Robin Murphy, Ioana Ciornei
[-- Attachment #1: Type: text/plain, Size: 51629 bytes --]
Hi Russell,
On 03.03.2020 17:49, Russell King - ARM Linux admin wrote:
> On Tue, Mar 03, 2020 at 04:18:57PM +0200, Laurentiu Tudor wrote:
>>
>>
>> On 28.02.2020 20:32, Robin Murphy wrote:
>>> [ +Laurentiu ]
>>>
>>> Hi Russell,
>>>
>>> Thanks for sharing a log, now I properly understand what's up... further
>>> comments at the end (for context).
>>>
>>> On 28/02/2020 10:06 am, Russell King - ARM Linux admin wrote:
>>>> On Fri, Feb 28, 2020 at 09:33:40AM +0000, John Garry wrote:
>>>>> On 28/02/2020 02:16, Lu Baolu wrote:
>>>>>> Hi,
>>>>>>
>>>>>> On 2020/2/27 19:57, Russell King wrote:
>>>>>>> On the LX2160A, there are lots (about 160) of IOMMU messages produced
>>>>>>> during boot; this is excessive. Reduce the severity of these messages
>>>>>>> to debug level.
>>>>>>>
>>>>>>> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
>>>>>>> ---
>>>>>>> drivers/iommu/iommu.c | 4 ++--
>>>>>>> 1 file changed, 2 insertions(+), 2 deletions(-)
>>>>>>>
>>>>>>> diff --git a/drivers/iommu/iommu.c b/drivers/iommu/iommu.c
>>>>>>> index 3ead597e1c57..304281ec623b 100644
>>>>>>> --- a/drivers/iommu/iommu.c
>>>>>>> +++ b/drivers/iommu/iommu.c
>>>>>>> @@ -741,7 +741,7 @@ int iommu_group_add_device(struct iommu_group
>>>>>>> *group, struct device *dev)
>>>>>>> trace_add_device_to_group(group->id, dev);
>>>>>>> - dev_info(dev, "Adding to iommu group %d\n", group->id);
>>>>>>> + dev_dbg(dev, "Adding to iommu group %d\n", group->id);
>>>>>>
>>>>>> I'm not strongly against this. But to me this message seems
>>>>>> to be a good
>>>>>> indicator that a device was probed successfully by the iommu subsystem.
>>>>>> Keeping it in the default kernel message always helps to the kernel
>>>>>> debugging.
>>>>>>
>>>>>
>>>>> I would tend to agree.
>>>>
>>>> Here's the boot messages. Notice how many of these "Adding to iommu
>>>> group" messages there are:
>>>>
>>>> [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083]
>>>> [ 0.000000] Linux version 5.5.0+ (rmk@rmk-PC) (gcc version 4.9.2
>>>> (GCC)) #655 SMP PREEMPT Fri Feb 28 09:54:47 GMT 2020
>>>> [ 0.000000] Machine model: SolidRun LX2160A Clearfog CX
>>>> [ 0.000000] earlycon: pl11 at MMIO32 0x00000000021c0000 (options '')
>>>> [ 0.000000] printk: bootconsole [pl11] enabled
>>>> [ 0.000000] efi: Getting EFI parameters from FDT:
>>>> [ 0.000000] efi: UEFI not found.
>>>> [ 0.000000] cma: Reserved 32 MiB at 0x00000000f9c00000
>>>> [ 0.000000] On node 0 totalpages: 1555968
>>>> [ 0.000000] DMA zone: 4096 pages used for memmap
>>>> [ 0.000000] DMA zone: 0 pages reserved
>>>> [ 0.000000] DMA zone: 262144 pages, LIFO batch:63
>>>> [ 0.000000] DMA32 zone: 3832 pages used for memmap
>>>> [ 0.000000] DMA32 zone: 245248 pages, LIFO batch:63
>>>> [ 0.000000] Normal zone: 16384 pages used for memmap
>>>> [ 0.000000] Normal zone: 1048576 pages, LIFO batch:63
>>>> [ 0.000000] psci: probing for conduit method from DT.
>>>> [ 0.000000] psci: PSCIv1.1 detected in firmware.
>>>> [ 0.000000] psci: Using standard PSCI v0.2 function IDs
>>>> [ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
>>>> [ 0.000000] psci: SMC Calling Convention v1.1
>>>> [ 0.000000] percpu: Embedded 31 pages/cpu s88968 r8192 d29816 u126976
>>>> [ 0.000000] pcpu-alloc: s88968 r8192 d29816 u126976 alloc=31*4096
>>>> [ 0.000000] pcpu-alloc: [0] 00 [0] 01 [0] 02 [0] 03 [0] 04 [0] 05
>>>> [0] 06 [0] 07
>>>> [ 0.000000] pcpu-alloc: [0] 08 [0] 09 [0] 10 [0] 11 [0] 12 [0] 13
>>>> [0] 14 [0] 15
>>>> [ 0.000000] Detected PIPT I-cache on CPU0
>>>> [ 0.000000] CPU features: detected: GIC system register CPU interface
>>>> [ 0.000000] CPU features: detected: EL2 vector hardening
>>>> [ 0.000000] Speculative Store Bypass Disable mitigation not required
>>>> [ 0.000000] CPU features: detected: ARM erratum 1319367
>>>> [ 0.000000] Built 1 zonelists, mobility grouping on. Total
>>>> pages: 1531656
>>>> [ 0.000000] Kernel command line: console=ttyAMA0,115200
>>>> root=PARTUUID=c7837e2f-02 rootwait earlycon=pl011,mmio32,0x21c0000
>>>> ramdisk_size=0 pci=pcie_bus_perf arm_smmu.disable_bypass=0
>>>> iommu.passthrough=0
>>>> [ 0.000000] Dentry cache hash table entries: 1048576 (order: 11,
>>>> 8388608 bytes, linear)
>>>> [ 0.000000] Inode-cache hash table entries: 524288 (order: 10,
>>>> 4194304 bytes, linear)
>>>> [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
>>>> [ 0.000000] software IO TLB: mapped [mem 0xbbfff000-0xbffff000] (64MB)
>>>> [ 0.000000] Memory: 5991500K/6223872K available (10172K kernel
>>>> code, 1376K rwdata, 3888K rodata, 960K init, 4326K bss, 199604K
>>>> reserved, 32768K cma-reserved)
>>>> [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=16,
>>>> Nodes=1
>>>> [ 0.000000] rcu: Preemptible hierarchical RCU implementation.
>>>> [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=64 to
>>>> nr_cpu_ids=16.
>>>> [ 0.000000] Tasks RCU enabled.
>>>> [ 0.000000] rcu: RCU calculated value of scheduler-enlistment
>>>> delay is 25 jiffies.
>>>> [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16,
>>>> nr_cpu_ids=16
>>>> [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
>>>> [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
>>>> [ 0.000000] GICv3: 256 SPIs implemented
>>>> [ 0.000000] GICv3: 0 Extended SPIs implemented
>>>> [ 0.000000] GICv3: Distributor has no Range Selector support
>>>> [ 0.000000] GICv3: 16 PPIs implemented
>>>> [ 0.000000] GICv3: no VLPI support, no direct LPI support
>>>> [ 0.000000] GICv3: CPU0: found redistributor 0 region
>>>> 0:0x0000000006200000
>>>> [ 0.000000] ITS [mem 0x06020000-0x0603ffff]
>>>> [ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices
>>>> @2178d00000 (flat, esz 8, psz 64K, shr 0)
>>>> [ 0.000000] ITS: using cache flushing for cmd queue
>>>> [ 0.000000] GICv3: using LPI property table @0x0000002178cd0000
>>>> [ 0.000000] GIC: using cache flushing for LPI property table
>>>> [ 0.000000] GICv3: CPU0: using allocated LPI pending table
>>>> @0x0000002178ce0000
>>>> [ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys).
>>>> [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff
>>>> max_cycles: 0x5c409fb33, max_idle_ns: 440795203156 ns
>>>> [ 0.000002] sched_clock: 56 bits at 25MHz, resolution 39ns, wraps
>>>> every 4398046511103ns
>>>> [ 0.006921] Console: colour dummy device 80x25
>>>> [ 0.010093] Lock dependency validator: Copyright (c) 2006 Red
>>>> Hat, Inc., Ingo Molnar
>>>> [ 0.016605] ... MAX_LOCKDEP_SUBCLASSES: 8
>>>> [ 0.019421] ... MAX_LOCK_DEPTH: 48
>>>> [ 0.022329] ... MAX_LOCKDEP_KEYS: 8192
>>>> [ 0.025408] ... CLASSHASH_SIZE: 4096
>>>> [ 0.028491] ... MAX_LOCKDEP_ENTRIES: 32768
>>>> [ 0.031659] ... MAX_LOCKDEP_CHAINS: 65536
>>>> [ 0.034830] ... CHAINHASH_SIZE: 32768
>>>> [ 0.037997] memory used by lock dependency info: 3509 kB
>>>> [ 0.042135] per task-struct memory footprint: 1920 bytes
>>>> [ 0.046292] Calibrating delay loop (skipped), value calculated
>>>> using timer frequency.. 50.00 BogoMIPS (lpj=100000)
>>>> [ 0.055443] pid_max: default: 32768 minimum: 301
>>>> [ 0.058844] LSM: Security Framework initializing
>>>> [ 0.062241] Mount-cache hash table entries: 16384 (order: 5,
>>>> 131072 bytes, linear)
>>>> [ 0.068602] Mountpoint-cache hash table entries: 16384 (order: 5,
>>>> 131072 bytes, linear)
>>>> [ 0.099452] ASID allocator initialised with 32768 entries
>>>> [ 0.111615] rcu: Hierarchical SRCU implementation.
>>>> [ 0.119672] Platform MSI: gic-its@6020000 domain created
>>>> [ 0.123765] PCI/MSI:
>>>> /interrupt-controller@6000000/gic-its@6020000 domain created
>>>> [ 0.130045] fsl-mc MSI:
>>>> /interrupt-controller@6000000/gic-its@6020000 domain created
>>>> [ 0.136572] EFI services will not be available.
>>>> [ 0.148587] smp: Bringing up secondary CPUs ...
>>>> [ 0.180732] Detected PIPT I-cache on CPU1
>>>> [ 0.180749] GICv3: CPU1: found redistributor 1 region
>>>> 0:0x0000000006220000
>>>> [ 0.180761] GICv3: CPU1: using allocated LPI pending table
>>>> @0x0000002178cf0000
>>>> [ 0.180781] CPU1: Booted secondary processor 0x0000000001 [0x410fd083]
>>>> [ 0.212781] Detected PIPT I-cache on CPU2
>>>> [ 0.212797] GICv3: CPU2: found redistributor 100 region
>>>> 0:0x0000000006240000
>>>> [ 0.212810] GICv3: CPU2: using allocated LPI pending table
>>>> @0x0000002178d80000
>>>> [ 0.212830] CPU2: Booted secondary processor 0x0000000100 [0x410fd083]
>>>> [ 0.244832] Detected PIPT I-cache on CPU3
>>>> [ 0.244844] GICv3: CPU3: found redistributor 101 region
>>>> 0:0x0000000006260000
>>>> [ 0.244855] GICv3: CPU3: using allocated LPI pending table
>>>> @0x0000002178d90000
>>>> [ 0.244871] CPU3: Booted secondary processor 0x0000000101 [0x410fd083]
>>>> [ 0.276894] Detected PIPT I-cache on CPU4
>>>> [ 0.276910] GICv3: CPU4: found redistributor 200 region
>>>> 0:0x0000000006280000
>>>> [ 0.276922] GICv3: CPU4: using allocated LPI pending table
>>>> @0x0000002178da0000
>>>> [ 0.276941] CPU4: Booted secondary processor 0x0000000200 [0x410fd083]
>>>> [ 0.308953] Detected PIPT I-cache on CPU5
>>>> [ 0.308966] GICv3: CPU5: found redistributor 201 region
>>>> 0:0x00000000062a0000
>>>> [ 0.308978] GICv3: CPU5: using allocated LPI pending table
>>>> @0x0000002178db0000
>>>> [ 0.308994] CPU5: Booted secondary processor 0x0000000201 [0x410fd083]
>>>> [ 0.341009] Detected PIPT I-cache on CPU6
>>>> [ 0.341027] GICv3: CPU6: found redistributor 300 region
>>>> 0:0x00000000062c0000
>>>> [ 0.341039] GICv3: CPU6: using allocated LPI pending table
>>>> @0x0000002178dc0000
>>>> [ 0.341058] CPU6: Booted secondary processor 0x0000000300 [0x410fd083]
>>>> [ 0.373064] Detected PIPT I-cache on CPU7
>>>> [ 0.373079] GICv3: CPU7: found redistributor 301 region
>>>> 0:0x00000000062e0000
>>>> [ 0.373091] GICv3: CPU7: using allocated LPI pending table
>>>> @0x0000002178dd0000
>>>> [ 0.373106] CPU7: Booted secondary processor 0x0000000301 [0x410fd083]
>>>> [ 0.405124] Detected PIPT I-cache on CPU8
>>>> [ 0.405143] GICv3: CPU8: found redistributor 400 region
>>>> 0:0x0000000006300000
>>>> [ 0.405156] GICv3: CPU8: using allocated LPI pending table
>>>> @0x0000002178de0000
>>>> [ 0.405175] CPU8: Booted secondary processor 0x0000000400 [0x410fd083]
>>>> [ 0.437179] Detected PIPT I-cache on CPU9
>>>> [ 0.437195] GICv3: CPU9: found redistributor 401 region
>>>> 0:0x0000000006320000
>>>> [ 0.437207] GICv3: CPU9: using allocated LPI pending table
>>>> @0x0000002178df0000
>>>> [ 0.437223] CPU9: Booted secondary processor 0x0000000401 [0x410fd083]
>>>> [ 0.469240] Detected PIPT I-cache on CPU10
>>>> [ 0.469261] GICv3: CPU10: found redistributor 500 region
>>>> 0:0x0000000006340000
>>>> [ 0.469273] GICv3: CPU10: using allocated LPI pending table
>>>> @0x0000002178e00000
>>>> [ 0.469293] CPU10: Booted secondary processor 0x0000000500
>>>> [0x410fd083]
>>>> [ 0.501296] Detected PIPT I-cache on CPU11
>>>> [ 0.501314] GICv3: CPU11: found redistributor 501 region
>>>> 0:0x0000000006360000
>>>> [ 0.501326] GICv3: CPU11: using allocated LPI pending table
>>>> @0x0000002178e10000
>>>> [ 0.501342] CPU11: Booted secondary processor 0x0000000501
>>>> [0x410fd083]
>>>> [ 0.533362] Detected PIPT I-cache on CPU12
>>>> [ 0.533385] GICv3: CPU12: found redistributor 600 region
>>>> 0:0x0000000006380000
>>>> [ 0.533397] GICv3: CPU12: using allocated LPI pending table
>>>> @0x0000002178e20000
>>>> [ 0.533418] CPU12: Booted secondary processor 0x0000000600
>>>> [0x410fd083]
>>>> [ 0.565408] Detected PIPT I-cache on CPU13
>>>> [ 0.565427] GICv3: CPU13: found redistributor 601 region
>>>> 0:0x00000000063a0000
>>>> [ 0.565440] GICv3: CPU13: using allocated LPI pending table
>>>> @0x0000002178e30000
>>>> [ 0.565455] CPU13: Booted secondary processor 0x0000000601
>>>> [0x410fd083]
>>>> [ 0.597470] Detected PIPT I-cache on CPU14
>>>> [ 0.597494] GICv3: CPU14: found redistributor 700 region
>>>> 0:0x00000000063c0000
>>>> [ 0.597507] GICv3: CPU14: using allocated LPI pending table
>>>> @0x0000002178e40000
>>>> [ 0.597527] CPU14: Booted secondary processor 0x0000000700
>>>> [0x410fd083]
>>>> [ 0.629523] Detected PIPT I-cache on CPU15
>>>> [ 0.629543] GICv3: CPU15: found redistributor 701 region
>>>> 0:0x00000000063e0000
>>>> [ 0.629556] GICv3: CPU15: using allocated LPI pending table
>>>> @0x0000002178e50000
>>>> [ 0.629571] CPU15: Booted secondary processor 0x0000000701
>>>> [0x410fd083]
>>>> [ 0.629684] smp: Brought up 1 node, 16 CPUs
>>>> [ 0.931457] SMP: Total of 16 processors activated.
>>>> [ 0.934986] CPU features: detected: 32-bit EL0 Support
>>>> [ 0.938858] CPU features: detected: CRC32 instructions
>>>> [ 0.947732] CPU features: emulated: Privileged Access Never (PAN)
>>>> using TTBR0_EL1 switching
>>>> [ 0.954876] CPU: All CPU(s) started at EL2
>>>> [ 0.957748] alternatives: patching kernel code
>>>> [ 0.961954] devtmpfs: initialized
>>>> [ 0.968138] random: get_random_u32 called from
>>>> bucket_table_alloc.isra.22+0x88/0x1e0 with crng_init=0
>>>> [ 0.976604] clocksource: jiffies: mask: 0xffffffff max_cycles:
>>>> 0xffffffff, max_idle_ns: 7645041785100000 ns
>>>> [ 0.985153] futex hash table entries: 4096 (order: 7, 524288
>>>> bytes, linear)
>>>> [ 0.991643] pinctrl core: initialized pinctrl subsystem
>>>> [ 0.996213] thermal_sys: Registered thermal governor 'step_wise'
>>>> [ 0.996473] DMI not present or invalid.
>>>> [ 1.004023] NET: Registered protocol family 16
>>>> [ 1.008239] DMA: preallocated 256 KiB pool for atomic allocations
>>>> [ 1.013102] audit: initializing netlink subsys (disabled)
>>>> [ 1.017340] audit: type=2000 audit(0.828:1): state=initialized
>>>> audit_enabled=0 res=1
>>>> [ 1.023873] cpuidle: using governor ladder
>>>> [ 1.026734] cpuidle: using governor menu
>>>> [ 1.029477] hw-breakpoint: found 6 breakpoint and 4 watchpoint
>>>> registers.
>>>> [ 1.035332] Serial: AMBA PL011 UART driver
>>>> [ 1.039319] Machine: SolidRun LX2160A Clearfog CX
>>>> [ 1.042751] SoC family: QorIQ LX2160A
>>>> [ 1.045135] SoC ID: svr:0x87361010, Revision: 1.0
>>>> [ 1.049775] 21c0000.serial: ttyAMA0 at MMIO 0x21c0000 (irq = 17,
>>>> base_baud = 0) is a SBSA
>>>> [ 1.056765] printk: console [ttyAMA0] enabled
>>>> [ 1.062890] printk: bootconsole [pl11] disabled
>>>> [ 1.069745] 21d0000.serial: ttyAMA1 at MMIO 0x21d0000 (irq = 18,
>>>> base_baud = 0) is a SBSA
>>>> [ 1.083284] fsl_mc_bus 80c000000.fsl-mc: MC firmware version: 10.18.0
>>>> [ 1.091046] fsl_mc_dprc dprc.1: DMA mask not set
>>>> [ 1.104098] HugeTLB registered 1.00 GiB page size, pre-allocated
>>>> 0 pages
>>>> [ 1.109500] HugeTLB registered 32.0 MiB page size, pre-allocated
>>>> 0 pages
>>>> [ 1.114906] HugeTLB registered 2.00 MiB page size, pre-allocated
>>>> 0 pages
>>>> [ 1.120298] HugeTLB registered 64.0 KiB page size, pre-allocated
>>>> 0 pages
>>>> [ 1.127238] cryptd: max_cpu_qlen set to 1000
>>>> [ 1.132187] iommu: Default domain type: Translated (set via
>>>> kernel command line)
>>>> [ 1.138411] vgaarb: loaded
>>>> [ 1.140045] SCSI subsystem initialized
>>>> [ 1.142660] libata version 3.00 loaded.
>>>> [ 1.142830] usbcore: registered new interface driver usbfs
>>>> [ 1.147050] usbcore: registered new interface driver hub
>>>> [ 1.151152] usbcore: registered new device driver usb
>>>> [ 1.155269] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery
>>>> not supported
>>>> [ 1.161373] i2c i2c-0: IMX I2C adapter registered
>>>> [ 1.164914] imx-i2c 2020000.i2c: can't get pinctrl, bus recovery
>>>> not supported
>>>> [ 1.170923] i2c i2c-1: IMX I2C adapter registered
>>>> [ 1.174438] imx-i2c 2040000.i2c: can't get pinctrl, bus recovery
>>>> not supported
>>>> [ 1.180489] i2c i2c-2: IMX I2C adapter registered
>>>> [ 1.184034] pps_core: LinuxPPS API ver. 1 registered
>>>> [ 1.187711] pps_core: Software ver. 5.3.6 - Copyright 2005-2007
>>>> Rodolfo Giometti <giometti@linux.it>
>>>> [ 1.195563] PTP clock support registered
>>>> [ 1.198926] clocksource: Switched to clocksource arch_sys_counter
>>>> [ 1.409271] VFS: Disk quotas dquot_6.6.0
>>>> [ 1.411929] VFS: Dquot-cache hash table entries: 512 (order 0,
>>>> 4096 bytes)
>>>> [ 1.423147] NET: Registered protocol family 2
>>>> [ 1.426524] tcp_listen_portaddr_hash hash table entries: 4096
>>>> (order: 6, 294912 bytes, linear)
>>>> [ 1.434212] TCP established hash table entries: 65536 (order: 7,
>>>> 524288 bytes, linear)
>>>> [ 1.441038] TCP bind hash table entries: 65536 (order: 10,
>>>> 4194304 bytes, linear)
>>>> [ 1.452946] TCP: Hash tables configured (established 65536 bind 65536)
>>>> [ 1.458362] UDP hash table entries: 4096 (order: 7, 655360 bytes,
>>>> linear)
>>>> [ 1.464637] UDP-Lite hash table entries: 4096 (order: 7, 655360
>>>> bytes, linear)
>>>> [ 1.471476] NET: Registered protocol family 1
>>>> [ 1.474948] RPC: Registered named UNIX socket transport module.
>>>> [ 1.479561] RPC: Registered udp transport module.
>>>> [ 1.482958] RPC: Registered tcp transport module.
>>>> [ 1.486348] RPC: Registered tcp NFSv4.1 backchannel transport module.
>>>> [ 1.491485] PCI: CLS 0 bytes, default 64
>>>> [ 1.495248] hw perfevents: enabled with armv8_cortex_a72 PMU
>>>> driver, 7 counters available
>>>> [ 1.502280] kvm: Limiting the IPA size due to kernel Virtual
>>>> Address limit
>>>> [ 1.507851] kvm [1]: IPA Size Limit: 43bits
>>>> [ 1.511572] kvm [1]: vgic-v2@c0e0000
>>>> [ 1.513851] kvm [1]: GIC system register CPU interface enabled
>>>> [ 1.518687] kvm [1]: vgic interrupt IRQ1
>>>> [ 1.521608] kvm [1]: Hyp mode initialized successfully
>>>> [ 1.535818] workingset: timestamp_bits=46 max_order=21 bucket_order=0
>>>> [ 1.549175] NFS: Registering the id_resolver key type
>>>> [ 1.552967] Key type id_resolver registered
>>>> [ 1.555844] Key type id_legacy registered
>>>> [ 1.558661] fuse: init (API version 7.31)
>>>> [ 1.561605] 9p: Installing v9fs 9p2000 file system support
>>>> [ 1.566505] io scheduler mq-deadline registered
>>>> [ 1.569734] io scheduler kyber registered
>>>> [ 1.573894] layerscape-pcie-gen4 3600000.pcie: host bridge
>>>> /soc/pcie@3600000 ranges:
>>>> [ 1.580351] layerscape-pcie-gen4 3600000.pcie: MEM
>>>> 0x9040000000..0x907fffffff -> 0x0040000000
>>>> [ 1.588204] layerscape-pcie-gen4 3600000.pcie: PCI host bridge to
>>>> bus 0000:00
>>>> [ 1.594036] pci_bus 0000:00: root bus resource [bus 00-ff]
>>>> [ 1.598216] pci_bus 0000:00: root bus resource [mem
>>>> 0x9040000000-0x907fffffff] (bus address [0x40000000-0x7fffffff])
>>>> [ 1.607459] pci 0000:00:00.0: [1957:8d90] type 01 class 0x060400
>>>> [ 1.612198] pci 0000:00:00.0: enabling Extended Tags
>>>> [ 1.615912] pci 0000:00:00.0: supports D1 D2
>>>> [ 1.618869] pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot
>>>> D3cold
>>>> [ 1.624897] pci 0000:01:00.0: [1cc1:8201] type 00 class 0x010802
>>>> [ 1.629666] pci 0000:01:00.0: reg 0x10: [mem
>>>> 0x9040000000-0x9040003fff 64bit]
>>>> [ 1.646977] pci 0000:00:00.0: up support 3 enabled 0
>>>> [ 1.650628] pci 0000:00:00.0: dn support 2 enabled 0
>>>> [ 1.654743] pci 0000:00:00.0: BAR 8: assigned [mem
>>>> 0x9040000000-0x90400fffff]
>>>> [ 1.660577] pci 0000:01:00.0: BAR 0: assigned [mem
>>>> 0x9040000000-0x9040003fff 64bit]
>>>> [ 1.666945] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
>>>> [ 1.670859] pci 0000:00:00.0: bridge window [mem
>>>> 0x9040000000-0x90400fffff]
>>>> [ 1.676698] pci 0000:00:00.0: Max Payload Size set to 256/ 256
>>>> (was 128), Max Read Rq 256
>>>> [ 1.683858] pci 0000:01:00.0: Max Payload Size set to 256/ 256
>>>> (was 128), Max Read Rq 256
>>>> [ 1.691047] pcieport 0000:00:00.0: PCIe capabilities: 0x13
>>>> [ 1.695230] pcieport 0000:00:00.0: init_service_irqs: -19
>>>> [ 1.699429] layerscape-pcie-gen4 3800000.pcie: host bridge
>>>> /soc/pcie@3800000 ranges:
>>>> [ 1.705877] layerscape-pcie-gen4 3800000.pcie: MEM
>>>> 0xa040000000..0xa07fffffff -> 0x0040000000
>>>> [ 1.713713] layerscape-pcie-gen4 3800000.pcie: PCI host bridge to
>>>> bus 0001:00
>>>> [ 1.719544] pci_bus 0001:00: root bus resource [bus 00-ff]
>>>> [ 1.723724] pci_bus 0001:00: root bus resource [mem
>>>> 0xa040000000-0xa07fffffff] (bus address [0x40000000-0x7fffffff])
>>>> [ 1.732950] pci 0001:00:00.0: [1957:8d90] type 01 class 0x060400
>>>> [ 1.737694] pci 0001:00:00.0: enabling Extended Tags
>>>> [ 1.741407] pci 0001:00:00.0: supports D1 D2
>>>> [ 1.744371] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot
>>>> D3cold
>>>> [ 1.750511] pci 0001:01:00.0: [15b3:6750] type 00 class 0x020000
>>>> [ 1.755600] pci 0001:01:00.0: reg 0x10: [mem
>>>> 0xa040000000-0xa0400fffff 64bit]
>>>> [ 1.761632] pci 0001:01:00.0: reg 0x18: [mem
>>>> 0xa040800000-0xa040ffffff 64bit pref]
>>>> [ 1.768286] pci 0001:01:00.0: reg 0x30: [mem
>>>> 0xa041000000-0xa0410fffff pref]
>>>> [ 1.787013] pci 0001:00:00.0: up support 3 enabled 0
>>>> [ 1.790665] pci 0001:00:00.0: dn support 1 enabled 0
>>>> [ 1.794787] pci 0001:00:00.0: BAR 9: assigned [mem
>>>> 0xa040000000-0xa0407fffff 64bit pref]
>>>> [ 1.801572] pci 0001:00:00.0: BAR 8: assigned [mem
>>>> 0xa040800000-0xa0409fffff]
>>>> [ 1.807404] pci 0001:01:00.0: BAR 2: assigned [mem
>>>> 0xa040000000-0xa0407fffff 64bit pref]
>>>> [ 1.814316] pci 0001:01:00.0: BAR 0: assigned [mem
>>>> 0xa040800000-0xa0408fffff 64bit]
>>>> [ 1.820793] pci 0001:01:00.0: BAR 6: assigned [mem
>>>> 0xa040900000-0xa0409fffff pref]
>>>> [ 1.827056] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
>>>> [ 1.830977] pci 0001:00:00.0: bridge window [mem
>>>> 0xa040800000-0xa0409fffff]
>>>> [ 1.836806] pci 0001:00:00.0: bridge window [mem
>>>> 0xa040000000-0xa0407fffff 64bit pref]
>>>> [ 1.843601] pci 0001:00:00.0: Max Payload Size set to 256/ 256
>>>> (was 128), Max Read Rq 256
>>>> [ 1.850903] pci 0001:01:00.0: Max Payload Size set to 256/ 256
>>>> (was 128), Max Read Rq 256
>>>> [ 1.858079] pcieport 0001:00:00.0: PCIe capabilities: 0x13
>>>> [ 1.862260] pcieport 0001:00:00.0: init_service_irqs: -19
>>>> [ 1.867322] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
>>>> [ 1.874084] arm-smmu 5000000.iommu: probing hardware configuration...
>>>> [ 1.879225] arm-smmu 5000000.iommu: SMMUv2 with:
>>>> [ 1.882529] arm-smmu 5000000.iommu: stage 1 translation
>>>> [ 1.886534] arm-smmu 5000000.iommu: stage 2 translation
>>>> [ 1.890539] arm-smmu 5000000.iommu: nested translation
>>>> [ 1.894457] arm-smmu 5000000.iommu: coherent table walk
>>>> [ 1.898461] arm-smmu 5000000.iommu: (IDR0.CTTW overridden by
>>>> FW configuration)
>>>> [ 1.904464] arm-smmu 5000000.iommu: stream matching with 128
>>>> register groups
>>>> [ 1.910294] arm-smmu 5000000.iommu: 64 context banks (0
>>>> stage-2 only)
>>>> [ 1.915519] arm-smmu 5000000.iommu: Supported page sizes:
>>>> 0x61311000
>>>> [ 1.920653] arm-smmu 5000000.iommu: Stage-1: 48-bit VA ->
>>>> 48-bit IPA
>>>> [ 1.925786] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA ->
>>>> 48-bit PA
>>>> [ 1.946137] loop: module loaded
>>>> [ 1.948871] nvme nvme0: pci function 0000:01:00.0
>>>> [ 1.952710] ahci-qoriq 3200000.sata: 3200000.sata supply ahci not
>>>> found, using dummy regulator
>>>> [ 1.960072] ahci-qoriq 3200000.sata: 3200000.sata supply phy not
>>>> found, using dummy regulator
>>>> [ 1.967335] ahci-qoriq 3200000.sata: 3200000.sata supply target
>>>> not found, using dummy regulator
>>>> [ 1.974957] ahci-qoriq 3200000.sata: AHCI 0001.0301 32 slots 1
>>>> ports 6 Gbps 0x1 impl platform mode
>>>> [ 1.982613] ahci-qoriq 3200000.sata: flags: 64bit ncq sntf pm clo
>>>> only pmp fbs pio slum part ccc sds apst
>>>> [ 1.991486] scsi host0: ahci-qoriq
>>>> [ 1.993859] ata1: SATA max UDMA/133 mmio [mem
>>>> 0x03200000-0x0320ffff] port 0x100 irq 24
>>>> [ 2.000561] ahci-qoriq 3210000.sata: 3210000.sata supply ahci not
>>>> found, using dummy regulator
>>>> [ 2.007916] ahci-qoriq 3210000.sata: 3210000.sata supply phy not
>>>> found, using dummy regulator
>>>> [ 2.015194] ahci-qoriq 3210000.sata: 3210000.sata supply target
>>>> not found, using dummy regulator
>>>> [ 2.022788] ahci-qoriq 3210000.sata: AHCI 0001.0301 32 slots 1
>>>> ports 6 Gbps 0x1 impl platform mode
>>>> [ 2.030443] ahci-qoriq 3210000.sata: flags: 64bit ncq sntf pm clo
>>>> only pmp fbs pio slum part ccc sds apst
>>>> [ 2.039256] scsi host1: ahci-qoriq
>>>> [ 2.041507] ata2: SATA max UDMA/133 mmio [mem
>>>> 0x03210000-0x0321ffff] port 0x100 irq 25
>>>> [ 2.048196] ahci-qoriq 3220000.sata: 3220000.sata supply ahci not
>>>> found, using dummy regulator
>>>> [ 2.055550] ahci-qoriq 3220000.sata: 3220000.sata supply phy not
>>>> found, using dummy regulator
>>>> [ 2.062811] ahci-qoriq 3220000.sata: 3220000.sata supply target
>>>> not found, using dummy regulator
>>>> [ 2.070378] ahci-qoriq 3220000.sata: AHCI 0001.0301 32 slots 1
>>>> ports 6 Gbps 0x1 impl platform mode
>>>> [ 2.078032] ahci-qoriq 3220000.sata: flags: 64bit ncq sntf pm clo
>>>> only pmp fbs pio slum part ccc sds apst
>>>> [ 2.084600] nvme nvme0: 15/0/0 default/read/poll queues
>>>> [ 2.086837] scsi host2: ahci-qoriq
>>>> [ 2.092574] ata3: SATA max UDMA/133 mmio [mem
>>>> 0x03220000-0x0322ffff] port 0x100 irq 26
>>>> [ 2.092925] nvme0n1: p1 p2
>>>> [ 2.099262] ahci-qoriq 3230000.sata: 3230000.sata supply ahci not
>>>> found, using dummy regulator
>>>> [ 2.108028] ahci-qoriq 3230000.sata: 3230000.sata supply phy not
>>>> found, using dummy regulator
>>>> [ 2.115290] ahci-qoriq 3230000.sata: 3230000.sata supply target
>>>> not found, using dummy regulator
>>>> [ 2.122864] ahci-qoriq 3230000.sata: AHCI 0001.0301 32 slots 1
>>>> ports 6 Gbps 0x1 impl platform mode
>>>> [ 2.130518] ahci-qoriq 3230000.sata: flags: 64bit ncq sntf pm clo
>>>> only pmp fbs pio slum part ccc sds apst
>>>> [ 2.139348] scsi host3: ahci-qoriq
>>>> [ 2.141598] ata4: SATA max UDMA/133 mmio [mem
>>>> 0x03230000-0x0323ffff] port 0x100 irq 27
>>>> [ 2.149539] libphy: Fixed MDIO Bus: probed
>>>> [ 2.152802] libphy: Freescale XGMAC MDIO Bus: probed
>>>> [ 2.156799] Qualcomm Atheros AR8035 8b96000:01: probe: irq=-1
>>>> [ 2.161245] Qualcomm Atheros AR8035 8b96000:01: probe: irq=-1
>>>> [ 2.165963] libphy: Freescale XGMAC MDIO Bus: probed
>>>> [ 2.170081] dwc3 3100000.usb: Failed to get clk 'ref': -2
>>>> [ 2.174468] dwc3 3110000.usb: Failed to get clk 'ref': -2
>>>> [ 2.179050] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
>>>> [ 2.184274] ehci-platform: EHCI generic platform driver
>>>> [ 2.188257] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
>>>> [ 2.193140] ohci-platform: OHCI generic platform driver
>>>> [ 2.197268] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
>>>> [ 2.201470] xhci-hcd xhci-hcd.0.auto: new USB bus registered,
>>>> assigned bus number 1
>>>> [ 2.207946] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci
>>>> version 0x100 quirks 0x0000000002010010
>>>> [ 2.216064] xhci-hcd xhci-hcd.0.auto: irq 22, io mem 0x03100000
>>>> [ 2.221416] hub 1-0:1.0: USB hub found
>>>> [ 2.223894] hub 1-0:1.0: 1 port detected
>>>> [ 2.226762] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
>>>> [ 2.230951] xhci-hcd xhci-hcd.0.auto: new USB bus registered,
>>>> assigned bus number 2
>>>> [ 2.237305] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
>>>> [ 2.242572] usb usb2: We don't know the algorithms for LPM for
>>>> this host, disabling LPM.
>>>> [ 2.249744] hub 2-0:1.0: USB hub found
>>>> [ 2.252209] hub 2-0:1.0: 1 port detected
>>>> [ 2.255118] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
>>>> [ 2.259309] xhci-hcd xhci-hcd.1.auto: new USB bus registered,
>>>> assigned bus number 3
>>>> [ 2.265760] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci
>>>> version 0x100 quirks 0x0000000002010010
>>>> [ 2.273872] xhci-hcd xhci-hcd.1.auto: irq 23, io mem 0x03110000
>>>> [ 2.279084] hub 3-0:1.0: USB hub found
>>>> [ 2.281538] hub 3-0:1.0: 1 port detected
>>>> [ 2.284380] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
>>>> [ 2.288571] xhci-hcd xhci-hcd.1.auto: new USB bus registered,
>>>> assigned bus number 4
>>>> [ 2.294930] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
>>>> [ 2.300190] usb usb4: We don't know the algorithms for LPM for
>>>> this host, disabling LPM.
>>>> [ 2.307363] hub 4-0:1.0: USB hub found
>>>> [ 2.309817] hub 4-0:1.0: 1 port detected
>>>> [ 2.312750] usbcore: registered new interface driver usb-storage
>>>> [ 2.317173] ata1: SATA link down (SStatus 0 SControl 300)
>>>> [ 2.317696] mousedev: PS/2 mouse device common for all mice
>>>> [ 2.331955] rtc-pcf2127-i2c 2-0051: registered as rtc0
>>>> [ 2.335876] i2c /dev entries driver
>>>> [ 2.339327] i2c i2c-0: Added multiplexed i2c bus 3
>>>> [ 2.343067] i2c i2c-0: Added multiplexed i2c bus 4
>>>> [ 2.346783] i2c i2c-0: Added multiplexed i2c bus 5
>>>> [ 2.350507] i2c i2c-0: Added multiplexed i2c bus 6
>>>> [ 2.354164] i2c i2c-0: Added multiplexed i2c bus 7
>>>> [ 2.357821] i2c i2c-0: Added multiplexed i2c bus 8
>>>> [ 2.361159] ata2: SATA link down (SStatus 0 SControl 300)
>>>> [ 2.361480] i2c i2c-0: Added multiplexed i2c bus 9
>>>> [ 2.369047] i2c i2c-0: Added multiplexed i2c bus 10
>>>> [ 2.372627] pca954x 0-0077: registered 8 multiplexed busses for
>>>> I2C mux pca9547
>>>> [ 2.378783] IR NEC protocol handler initialized
>>>> [ 2.382010] IR RC5(x/sz) protocol handler initialized
>>>> [ 2.385755] IR RC6 protocol handler initialized
>>>> [ 2.388977] IR JVC protocol handler initialized
>>>> [ 2.392200] IR Sony protocol handler initialized
>>>> [ 2.395513] IR SANYO protocol handler initialized
>>>> [ 2.398903] IR Sharp protocol handler initialized
>>>> [ 2.402300] IR MCE Keyboard/mouse protocol handler initialized
>>>> [ 2.406827] IR XMP protocol handler initialized
>>>> [ 2.413367] amc6821 4-0018: Error reading configuration register,
>>>> aborting.
>>>> [ 2.417180] ata3: SATA link down (SStatus 0 SControl 300)
>>>> [ 2.419034] amc6821: probe of 4-0018 failed with error -5
>>>> [ 2.427436] sdhci: Secure Digital Host Controller Interface driver
>>>> [ 2.432314] sdhci: Copyright(c) Pierre Ossman
>>>> [ 2.435384] sdhci-pltfm: SDHCI platform and OF driver helper
>>>> [ 2.461157] ata4: SATA link down (SStatus 0 SControl 300)
>>>> [ 2.465487] mmc0: SDHCI controller on 2140000.esdhc
>>>> [2140000.esdhc] using ADMA 64-bit
>>>> [ 2.494954] mmc1: SDHCI controller on 2150000.esdhc
>>>> [2150000.esdhc] using ADMA 64-bit
>>>> [ 2.502071] ledtrig-cpu: registered to indicate activity on CPUs
>>>> [ 2.507175] caam 8000000.crypto: device ID = 0x0a1a020000000000
>>>> (Era 10)
>>>> [ 2.508538] mmc0: new high speed SDHC card at address aaaa
>>>> [ 2.512572] caam 8000000.crypto: job rings = 3, qi = 1
>>>> [ 2.521006] mmcblk0: mmc0:aaaa SU04G 3.69 GiB (ro)
>>>> [ 2.525840] caam algorithms registered in /proc/crypto
>>>> [ 2.532365] caam 8000000.crypto: caam pkc algorithms registered
>>>> in /proc/crypto
>>>> [ 2.539400] caam_jr 8010000.jr: registering rng-caam
>>>> [ 2.543736] usbcore: registered new interface driver usbhid
>>>> [ 2.548007] usbhid: USB HID core driver
>>>> [ 2.551148] NET: Registered protocol family 10
>>>> [ 2.554963] Segment Routing with IPv6
>>>> [ 2.557343] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
>>>> [ 2.562313] NET: Registered protocol family 17
>>>> [ 2.565629] 9pnet: Installing 9P2000 support
>>>> [ 2.568641] Key type dns_resolver registered
>>>> [ 2.571820] registered taskstats version 1
>>>> [ 2.578646] fsl_mc_dprc dprc.1: Adding to iommu group 0
>>>> [ 2.584473] mmc1: new HS400 MMC card at address 0001
>>>> [ 2.592566] mmcblk1: mmc1:0001 DF4064 58.2 GiB
>>>> [ 2.595945] mmcblk1boot0: mmc1:0001 DF4064 partition 1 4.00 MiB
>>>> [ 2.600717] mmcblk1boot1: mmc1:0001 DF4064 partition 2 4.00 MiB
>>>> [ 2.605471] mmcblk1rpmb: mmc1:0001 DF4064 partition 3 4.00 MiB,
>>>> chardev (246:0)
>>>> [ 2.612749] mmcblk1: p1 p2
>>>> [ 2.622945] usb 3-1: new high-speed USB device number 2 using xhci-hcd
>>>> [ 2.642000] fsl_dpaa2_eth dpni.0: Adding to iommu group 0
>>>> [ 2.646254] fsl_mc_dprc dprc.1: No more resources of type dpmcp left
>>>> [ 2.651688] fsl_mc_allocator dpbp.1: Adding to iommu group 0
>>>> [ 2.656161] fsl_mc_allocator dpbp.0: Adding to iommu group 0
>>>> [ 2.662117] fsl_mc_allocator dpmcp.35: Adding to iommu group 0
>>>> [ 2.667765] fsl_mc_allocator dpmcp.34: Adding to iommu group 0
>>>> [ 2.673422] fsl_mc_allocator dpmcp.33: Adding to iommu group 0
>>>> [ 2.679071] fsl_mc_allocator dpmcp.32: Adding to iommu group 0
>>>> [ 2.684267] hub 3-1:1.0: USB hub found
>>>> [ 2.684727] fsl_mc_allocator dpmcp.31: Adding to iommu group 0
>>>> [ 2.686736] hub 3-1:1.0: 4 ports detected
>>>> [ 2.692343] fsl_mc_allocator dpmcp.30: Adding to iommu group 0
>>>> [ 2.699627] fsl_mc_allocator dpmcp.29: Adding to iommu group 0
>>>> [ 2.705265] fsl_mc_allocator dpmcp.28: Adding to iommu group 0
>>>> [ 2.710952] fsl_mc_allocator dpmcp.27: Adding to iommu group 0
>>>> [ 2.716596] fsl_mc_allocator dpmcp.26: Adding to iommu group 0
>>>> [ 2.722243] fsl_mc_allocator dpmcp.25: Adding to iommu group 0
>>>> [ 2.727897] fsl_mc_allocator dpmcp.24: Adding to iommu group 0
>>>> [ 2.733550] fsl_mc_allocator dpmcp.23: Adding to iommu group 0
>>>> [ 2.739198] fsl_mc_allocator dpmcp.22: Adding to iommu group 0
>>>> [ 2.744853] fsl_mc_allocator dpmcp.21: Adding to iommu group 0
>>>> [ 2.750495] fsl_mc_allocator dpmcp.20: Adding to iommu group 0
>>>> [ 2.756161] fsl_mc_allocator dpmcp.19: Adding to iommu group 0
>>>> [ 2.761803] fsl_mc_allocator dpmcp.18: Adding to iommu group 0
>>>> [ 2.767473] fsl_mc_allocator dpmcp.17: Adding to iommu group 0
>>>> [ 2.773117] fsl_mc_allocator dpmcp.16: Adding to iommu group 0
>>>> [ 2.778768] fsl_mc_allocator dpmcp.15: Adding to iommu group 0
>>>> [ 2.782959] usb 4-1: new SuperSpeed Gen 1 USB device number 2
>>>> using xhci-hcd
>>>> [ 2.784414] fsl_mc_allocator dpmcp.14: Adding to iommu group 0
>>>> [ 2.794669] fsl_mc_allocator dpmcp.13: Adding to iommu group 0
>>>> [ 2.800309] fsl_mc_allocator dpmcp.12: Adding to iommu group 0
>>>> [ 2.805969] fsl_mc_allocator dpmcp.11: Adding to iommu group 0
>>>> [ 2.811625] fsl_mc_allocator dpmcp.10: Adding to iommu group 0
>>>> [ 2.817271] fsl_mc_allocator dpmcp.9: Adding to iommu group 0
>>>> [ 2.822845] fsl_mc_allocator dpmcp.8: Adding to iommu group 0
>>>> [ 2.828243] hub 4-1:1.0: USB hub found
>>>> [ 2.828420] fsl_mc_allocator dpmcp.7: Adding to iommu group 0
>>>> [ 2.830710] hub 4-1:1.0: 4 ports detected
>>>> [ 2.836276] fsl_mc_allocator dpmcp.6: Adding to iommu group 0
>>>> [ 2.843415] fsl_mc_allocator dpmcp.5: Adding to iommu group 0
>>>> [ 2.848975] fsl_mc_allocator dpmcp.4: Adding to iommu group 0
>>>> [ 2.851038] random: fast init done
>>>> [ 2.854534] fsl_mc_allocator dpmcp.3: Adding to iommu group 0
>>>> [ 2.861060] fsl_mc_allocator dpmcp.2: Adding to iommu group 0
>>>> [ 2.866622] fsl_mc_allocator dpmcp.1: Adding to iommu group 0
>>>> [ 2.874308] fsl_mc_dpio dpio.15: Adding to iommu group 0
>>>> [ 2.882022] fsl_mc_dpio dpio.15: probed
>>>> [ 2.888261] fsl_mc_dpio dpio.14: Adding to iommu group 0
>>>> [ 2.895912] fsl_mc_dpio dpio.14: probed
>>>> [ 2.902061] fsl_mc_dpio dpio.13: Adding to iommu group 0
>>>> [ 2.909710] fsl_mc_dpio dpio.13: probed
>>>> [ 2.915939] fsl_mc_dpio dpio.12: Adding to iommu group 0
>>>> [ 2.923591] fsl_mc_dpio dpio.12: probed
>>>> [ 2.929752] fsl_mc_dpio dpio.11: Adding to iommu group 0
>>>> [ 2.937396] fsl_mc_dpio dpio.11: probed
>>>> [ 2.943628] fsl_mc_dpio dpio.10: Adding to iommu group 0
>>>> [ 2.951283] fsl_mc_dpio dpio.10: probed
>>>> [ 2.957446] fsl_mc_dpio dpio.9: Adding to iommu group 0
>>>> [ 2.965012] fsl_mc_dpio dpio.9: probed
>>>> [ 2.971167] fsl_mc_dpio dpio.8: Adding to iommu group 0
>>>> [ 2.978776] fsl_mc_dpio dpio.8: probed
>>>> [ 2.984923] fsl_mc_dpio dpio.7: Adding to iommu group 0
>>>> [ 2.992537] fsl_mc_dpio dpio.7: probed
>>>> [ 2.998684] fsl_mc_dpio dpio.6: Adding to iommu group 0
>>>> [ 3.006299] fsl_mc_dpio dpio.6: probed
>>>> [ 3.012440] fsl_mc_dpio dpio.5: Adding to iommu group 0
>>>> [ 3.020064] fsl_mc_dpio dpio.5: probed
>>>> [ 3.026190] fsl_mc_dpio dpio.4: Adding to iommu group 0
>>>> [ 3.033754] fsl_mc_dpio dpio.4: probed
>>>> [ 3.038937] usb 3-1.3: new high-speed USB device number 3 using
>>>> xhci-hcd
>>>> [ 3.039844] fsl_mc_dpio dpio.3: Adding to iommu group 0
>>>> [ 3.051890] fsl_mc_dpio dpio.3: probed
>>>> [ 3.058009] fsl_mc_dpio dpio.2: Adding to iommu group 0
>>>> [ 3.065609] fsl_mc_dpio dpio.2: probed
>>>> [ 3.071763] fsl_mc_dpio dpio.1: Adding to iommu group 0
>>>> [ 3.079384] fsl_mc_dpio dpio.1: probed
>>>> [ 3.085521] fsl_mc_dpio dpio.0: Adding to iommu group 0
>>>> [ 3.093136] fsl_mc_dpio dpio.0: probed
>>>> [ 3.096201] fsl_mc_allocator dpcon.31: Adding to iommu group 0
>>>> [ 3.100196] hub 3-1.3:1.0: USB hub found
>>>> [ 3.100860] fsl_mc_allocator dpcon.30: Adding to iommu group 0
>>>> [ 3.103374] hub 3-1.3:1.0: 4 ports detected
>>>> [ 3.107983] fsl_mc_allocator dpcon.29: Adding to iommu group 0
>>>> [ 3.115381] fsl_mc_allocator dpcon.28: Adding to iommu group 0
>>>> [ 3.120030] fsl_mc_allocator dpcon.27: Adding to iommu group 0
>>>> [ 3.124682] fsl_mc_allocator dpcon.26: Adding to iommu group 0
>>>> [ 3.129333] fsl_mc_allocator dpcon.25: Adding to iommu group 0
>>>> [ 3.133987] fsl_mc_allocator dpcon.24: Adding to iommu group 0
>>>> [ 3.138642] fsl_mc_allocator dpcon.23: Adding to iommu group 0
>>>> [ 3.143294] fsl_mc_allocator dpcon.22: Adding to iommu group 0
>>>> [ 3.147946] fsl_mc_allocator dpcon.21: Adding to iommu group 0
>>>> [ 3.152597] fsl_mc_allocator dpcon.20: Adding to iommu group 0
>>>> [ 3.157250] fsl_mc_allocator dpcon.19: Adding to iommu group 0
>>>> [ 3.161903] fsl_mc_allocator dpcon.18: Adding to iommu group 0
>>>> [ 3.166559] fsl_mc_allocator dpcon.17: Adding to iommu group 0
>>>> [ 3.171217] fsl_mc_allocator dpcon.16: Adding to iommu group 0
>>>> [ 3.175871] fsl_mc_allocator dpcon.15: Adding to iommu group 0
>>>> [ 3.180533] fsl_mc_allocator dpcon.14: Adding to iommu group 0
>>>> [ 3.185188] fsl_mc_allocator dpcon.13: Adding to iommu group 0
>>>> [ 3.189844] fsl_mc_allocator dpcon.12: Adding to iommu group 0
>>>> [ 3.194499] fsl_mc_allocator dpcon.11: Adding to iommu group 0
>>>> [ 3.199153] fsl_mc_allocator dpcon.10: Adding to iommu group 0
>>>> [ 3.203810] fsl_mc_allocator dpcon.9: Adding to iommu group 0
>>>> [ 3.208385] fsl_mc_allocator dpcon.8: Adding to iommu group 0
>>>> [ 3.212956] fsl_mc_allocator dpcon.7: Adding to iommu group 0
>>>> [ 3.217526] fsl_mc_allocator dpcon.6: Adding to iommu group 0
>>>> [ 3.222096] fsl_mc_allocator dpcon.5: Adding to iommu group 0
>>>> [ 3.226667] fsl_mc_allocator dpcon.4: Adding to iommu group 0
>>>> [ 3.231237] fsl_mc_allocator dpcon.3: Adding to iommu group 0
>>>> [ 3.235812] fsl_mc_allocator dpcon.2: Adding to iommu group 0
>>>> [ 3.240383] fsl_mc_allocator dpcon.1: Adding to iommu group 0
>>>> [ 3.244955] fsl_mc_allocator dpcon.0: Adding to iommu group 0
>>>> [ 3.252565] fsl_mc_dprc dprc.1: DPRC device bound to driver
>>>> [ 3.257032] libphy: SFP I2C Bus: probed
>>>> [ 3.259658] sfp sfp-0: Host maximum power 2.0W
>>>> [ 3.262929] sfp sfp-0: No tx_disable pin: SFP modules will always
>>>> be emitting.
>>>> [ 3.269061] libphy: SFP I2C Bus: probed
>>>> [ 3.271642] sfp sfp-1: Host maximum power 2.0W
>>>> [ 3.274884] sfp sfp-1: No tx_disable pin: SFP modules will always
>>>> be emitting.
>>>> [ 3.280979] libphy: SFP I2C Bus: probed
>>>> [ 3.283559] sfp sfp-2: Host maximum power 2.0W
>>>> [ 3.286819] sfp sfp-2: No tx_disable pin: SFP modules will always
>>>> be emitting.
>>>> [ 3.292948] libphy: SFP I2C Bus: probed
>>>> [ 3.295529] sfp sfp-3: Host maximum power 2.0W
>>>> [ 3.298768] sfp sfp-3: No tx_disable pin: SFP modules will always
>>>> be emitting.
>>>> [ 3.456609] fsl_dpaa2_eth dpni.0 (unnamed net_device)
>>>> (uninitialized): PHY [8b96000:01] driver [Qualcomm Atheros AR8035]
>>>> (irq=POLL)
>>>> [ 3.467153] fsl_dpaa2_eth dpni.0 (unnamed net_device)
>>>> (uninitialized): phy: setting supported 000,00000200,000062ea
>>>> advertising 000,00000200,000062ea
>>>> [ 3.468341] fsl_dpaa2_eth dpni.0: Probed interface eth0
>>>> [ 3.472672] input: gpio-keys as
>>>> /devices/platform/gpio-keys/input/input0
>>>> [ 3.479780] rtc-pcf2127-i2c 2-0051: setting system clock to
>>>> 2020-02-28T09:56:18 UTC (1582883778)
>>>> [ 3.490224] EXT4-fs (nvme0n1p2): mounted filesystem with ordered
>>>> data mode. Opts: (null)
>>>> [ 3.497082] VFS: Mounted root (ext4 filesystem) readonly on
>>>> device 259:2.
>>>> [ 3.503193] devtmpfs: mounted
>>>> [ 3.505079] Freeing unused kernel memory: 960K
>>>> [ 3.534993] Run /sbin/init as init process
>>>>
>>>> When asking for more network interfaces, more "Adding to iommu group"
>>>> messages get spat out:
>>>>
>>>> [ 446.040825] fsl_dpaa2_eth dpni.1: Adding to iommu group 0
>>>> [ 446.201254] libphy: Freescale XGMAC MDIO Bus: probed
>>>> [ 446.206552] fsl_dpaa2_eth dpni.1: Probed interface eth1
>>>> [ 446.210715] fsl_mc_allocator dpbp.2: Adding to iommu group 0
>>>> [ 446.216838] fsl_mc_allocator dpmcp.36: Adding to iommu group 0
>>>> [ 446.224808] fsl_mc_allocator dpcon.47: Adding to iommu group 0
>>>> [ 446.229935] fsl_mc_allocator dpcon.46: Adding to iommu group 0
>>>> [ 446.234685] fsl_mc_allocator dpcon.45: Adding to iommu group 0
>>>> [ 446.239431] fsl_mc_allocator dpcon.44: Adding to iommu group 0
>>>> [ 446.244179] fsl_mc_allocator dpcon.43: Adding to iommu group 0
>>>> [ 446.251725] fsl_mc_allocator dpcon.42: Adding to iommu group 0
>>>> [ 446.258952] fsl_mc_allocator dpcon.41: Adding to iommu group 0
>>>> [ 446.263666] fsl_mc_allocator dpcon.40: Adding to iommu group 0
>>>> [ 446.268377] fsl_mc_allocator dpcon.39: Adding to iommu group 0
>>>> [ 446.273086] fsl_mc_allocator dpcon.38: Adding to iommu group 0
>>>> [ 446.277814] fsl_mc_allocator dpcon.37: Adding to iommu group 0
>>>> [ 446.282517] fsl_mc_allocator dpcon.36: Adding to iommu group 0
>>>> [ 446.287228] fsl_mc_allocator dpcon.35: Adding to iommu group 0
>>>> [ 446.291935] fsl_mc_allocator dpcon.34: Adding to iommu group 0
>>>> [ 446.296641] fsl_mc_allocator dpcon.33: Adding to iommu group 0
>>>> [ 446.301354] fsl_mc_allocator dpcon.32: Adding to iommu group 0
>>>> [ 446.893939] fsl_dpaa2_eth dpni.2: Adding to iommu group 0
>>>> [ 447.052868] libphy: Freescale XGMAC MDIO Bus: probed
>>>> [ 447.058223] fsl_dpaa2_eth dpni.2: Probed interface eth2
>>>> [ 447.062425] fsl_mc_allocator dpbp.3: Adding to iommu group 0
>>>> [ 447.068813] fsl_mc_allocator dpmcp.37: Adding to iommu group 0
>>>> [ 447.074280] fsl_mc_allocator dpcon.63: Adding to iommu group 0
>>>> [ 447.078995] fsl_mc_allocator dpcon.62: Adding to iommu group 0
>>>> [ 447.088690] fsl_mc_allocator dpcon.61: Adding to iommu group 0
>>>> [ 447.093639] fsl_mc_allocator dpcon.60: Adding to iommu group 0
>>>> [ 447.098369] fsl_mc_allocator dpcon.59: Adding to iommu group 0
>>>> [ 447.103089] fsl_mc_allocator dpcon.58: Adding to iommu group 0
>>>> [ 447.107811] fsl_mc_allocator dpcon.57: Adding to iommu group 0
>>>> [ 447.112525] fsl_mc_allocator dpcon.56: Adding to iommu group 0
>>>> [ 447.117244] fsl_mc_allocator dpcon.55: Adding to iommu group 0
>>>> [ 447.121962] fsl_mc_allocator dpcon.54: Adding to iommu group 0
>>>> [ 447.126680] fsl_mc_allocator dpcon.53: Adding to iommu group 0
>>>> [ 447.131392] fsl_mc_allocator dpcon.52: Adding to iommu group 0
>>>> [ 447.136107] fsl_mc_allocator dpcon.51: Adding to iommu group 0
>>>> [ 447.140820] fsl_mc_allocator dpcon.50: Adding to iommu group 0
>>>> [ 447.145535] fsl_mc_allocator dpcon.49: Adding to iommu group 0
>>>> [ 447.150249] fsl_mc_allocator dpcon.48: Adding to iommu group 0
>>>> [ 447.710694] fsl_dpaa2_eth dpni.3: Adding to iommu group 0
>>>> [ 447.888120] libphy: Freescale XGMAC MDIO Bus: probed
>>>> [ 447.893479] fsl_dpaa2_eth dpni.3: Probed interface eth3
>>>> [ 447.897740] fsl_mc_allocator dpbp.4: Adding to iommu group 0
>>>> [ 447.904488] fsl_mc_allocator dpmcp.38: Adding to iommu group 0
>>>> [ 447.909994] fsl_mc_allocator dpcon.79: Adding to iommu group 0
>>>> [ 447.914717] fsl_mc_allocator dpcon.78: Adding to iommu group 0
>>>> [ 447.919852] fsl_mc_allocator dpcon.77: Adding to iommu group 0
>>>> [ 447.924720] fsl_mc_allocator dpcon.76: Adding to iommu group 0
>>>> [ 447.931979] fsl_mc_allocator dpcon.75: Adding to iommu group 0
>>>> [ 447.939172] fsl_mc_allocator dpcon.74: Adding to iommu group 0
>>>> [ 447.943886] fsl_mc_allocator dpcon.73: Adding to iommu group 0
>>>> [ 447.948604] fsl_mc_allocator dpcon.72: Adding to iommu group 0
>>>> [ 447.953319] fsl_mc_allocator dpcon.71: Adding to iommu group 0
>>>> [ 447.958035] fsl_mc_allocator dpcon.70: Adding to iommu group 0
>>>> [ 447.965445] fsl_mc_allocator dpcon.69: Adding to iommu group 0
>>>> [ 447.972653] fsl_mc_allocator dpcon.68: Adding to iommu group 0
>>>> [ 447.977376] fsl_mc_allocator dpcon.67: Adding to iommu group 0
>>>> [ 447.982097] fsl_mc_allocator dpcon.66: Adding to iommu group 0
>>>> [ 447.986816] fsl_mc_allocator dpcon.65: Adding to iommu group 0
>>>> [ 447.991532] fsl_mc_allocator dpcon.64: Adding to iommu group 0
>>>> [ 448.737198] fsl_dpaa2_eth dpni.4: Adding to iommu group 0
>>>> [ 448.894480] libphy: Freescale XGMAC MDIO Bus: probed
>>>> [ 448.899785] fsl_dpaa2_eth dpni.4: Probed interface eth4
>>>> [ 448.904077] fsl_mc_allocator dpbp.5: Adding to iommu group 0
>>>> [ 448.909817] fsl_mc_allocator dpmcp.39: Adding to iommu group 0
>>>> [ 448.915340] fsl_mc_allocator dpcon.95: Adding to iommu group 0
>>>> [ 448.920068] fsl_mc_allocator dpcon.94: Adding to iommu group 0
>>>> [ 448.924789] fsl_mc_allocator dpcon.93: Adding to iommu group 0
>>>> [ 448.929689] fsl_mc_allocator dpcon.92: Adding to iommu group 0
>>>> [ 448.934436] fsl_mc_allocator dpcon.91: Adding to iommu group 0
>>>> [ 448.939159] fsl_mc_allocator dpcon.90: Adding to iommu group 0
>>>> [ 448.943882] fsl_mc_allocator dpcon.89: Adding to iommu group 0
>>>> [ 448.948607] fsl_mc_allocator dpcon.88: Adding to iommu group 0
>>>> [ 448.953327] fsl_mc_allocator dpcon.87: Adding to iommu group 0
>>>> [ 448.958050] fsl_mc_allocator dpcon.86: Adding to iommu group 0
>>>> [ 448.962771] fsl_mc_allocator dpcon.85: Adding to iommu group 0
>>>> [ 448.967499] fsl_mc_allocator dpcon.84: Adding to iommu group 0
>>>> [ 448.972219] fsl_mc_allocator dpcon.83: Adding to iommu group 0
>>>> [ 448.976941] fsl_mc_allocator dpcon.82: Adding to iommu group 0
>>>> [ 448.981669] fsl_mc_allocator dpcon.81: Adding to iommu group 0
>>>> [ 448.986391] fsl_mc_allocator dpcon.80: Adding to iommu group 0
>>>>
>>>> # dmesg |grep 'Adding to iommu' | wc -l
>>>> 164
>>>> # dmesg |grep -v 'Adding to iommu' | wc -l
>>>> 551
>>>>
>>>> So, 23% of the kernel messages on this platform are "Adding to iommu",
>>>> which is excessive.
>>>
>>> Indeed, however I would note that on most platforms bringing up a
>>> network interface involves hot-adding 0 devices, so hot-adding 19
>>> devices as full-blown DMA masters is arguably the root of "excessive"
>>> already. Per the concern I initially raised, each of those messages
>>> represents a whole bunch of internal allocation and bookkeeping going
>>> on, which if it isn't necessary would be far better avoided altogether,
>>> than simply done more quietly.
>>>
>>> Laurentiu, I guess at the moment the nature of the of_dma_configure()
>>> integration means we end up treating all DPAA2 objects identically, but
>>> do you think we have scope to be a bit cleverer in that regard?
>>> Presumably not every type of object that shows up on the fsl_mc bus is
>>> really an independent DMA master, so if we could skip doing the full
>>> DMA/IOMMU/MSI setup for the ones that don't need it, it would work out
>>> nicer all round. In fact your .dma_configure proposal (which I'll try to
>>> take a proper look at next week) couldn't have come at a better time for
>>> that argument :)
>>>
>>
>> Just FYI, I've tried Robin's suggestion and things greatly improved [1], so
>> I think we can leave the iommu group messages alone.
>>
>> [1]
>> # dmesg |grep 'Adding to iommu' | wc -l
>> 7
>> # dmesg |grep -v 'Adding to iommu' | wc -l
>> 512
>
> Please can you send me your patches for this.
>
Please see attached for now. I plan to also submit a new round on the
lists sometime this week I think. Will keep you in the loop.
---
Best Regards, Laurentiu
[-- Attachment #2: 0001-bus-fsl-mc-add-custom-.dma_configure-implementation.patch --]
[-- Type: text/x-patch, Size: 2391 bytes --]
From c98dc05cdd45ae923654f2427985bd28bcde4bb2 Mon Sep 17 00:00:00 2001
From: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Date: Thu, 13 Feb 2020 11:59:12 +0200
Subject: [PATCH 1/4] bus: fsl-mc: add custom .dma_configure implementation
Content-Type: text/plain; charset="us-ascii"
The devices on this bus are not discovered by way of device tree
but by queries to the firmware. It makes little sense to trick the
generic of layer into thinking that these devices are of related so
that we can get our dma configuration. Instead of doing that, add
our custom dma configuration implementation.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
---
drivers/bus/fsl-mc/fsl-mc-bus.c | 42 ++++++++++++++++++++++++++++++++-
1 file changed, 41 insertions(+), 1 deletion(-)
diff --git a/drivers/bus/fsl-mc/fsl-mc-bus.c b/drivers/bus/fsl-mc/fsl-mc-bus.c
index 36eb25f82c8e..3df015eedae4 100644
--- a/drivers/bus/fsl-mc/fsl-mc-bus.c
+++ b/drivers/bus/fsl-mc/fsl-mc-bus.c
@@ -132,11 +132,51 @@ static int fsl_mc_bus_uevent(struct device *dev, struct kobj_uevent_env *env)
static int fsl_mc_dma_configure(struct device *dev)
{
struct device *dma_dev = dev;
+ struct iommu_fwspec *fwspec;
+ const struct iommu_ops *iommu_ops;
+ struct fsl_mc_device *mc_dev = to_fsl_mc_device(dev);
+ int ret;
+ u32 icid;
+
+ /* Skip DMA setup for devices that are not DMA masters */
+ if (dev->type == &fsl_mc_bus_dpmcp_type ||
+ dev->type == &fsl_mc_bus_dpbp_type ||
+ dev->type == &fsl_mc_bus_dpcon_type ||
+ dev->type == &fsl_mc_bus_dpio_type)
+ return 0;
while (dev_is_fsl_mc(dma_dev))
dma_dev = dma_dev->parent;
- return of_dma_configure(dev, dma_dev->of_node, 0);
+ fwspec = dev_iommu_fwspec_get(dma_dev);
+ if (!fwspec)
+ return -ENODEV;
+ iommu_ops = iommu_ops_from_fwnode(fwspec->iommu_fwnode);
+ if (!iommu_ops)
+ return -ENODEV;
+
+ ret = iommu_fwspec_init(dev, fwspec->iommu_fwnode, iommu_ops);
+ if (ret)
+ return ret;
+
+ icid = mc_dev->icid;
+ ret = iommu_fwspec_add_ids(dev, &icid, 1);
+ if (ret) {
+ iommu_fwspec_free(dev);
+ return ret;
+ }
+
+ if (!device_iommu_mapped(dev)) {
+ ret = iommu_probe_device(dev);
+ if (ret) {
+ iommu_fwspec_free(dev);
+ return ret;
+ }
+ }
+
+ arch_setup_dma_ops(dev, 0, *dma_dev->dma_mask + 1, iommu_ops, true);
+
+ return 0;
}
static ssize_t modalias_show(struct device *dev, struct device_attribute *attr,
--
2.17.1
[-- Attachment #3: 0002-irqchip-fsl-mc-Change-the-way-the-IRQ-domain-is-set-.patch --]
[-- Type: text/x-patch, Size: 1818 bytes --]
From 699bee97783087db3ead59c7b84fb7a4ce17274e Mon Sep 17 00:00:00 2001
From: Diana Craciun <diana.craciun@oss.nxp.com>
Date: Fri, 14 Feb 2020 16:28:45 +0200
Subject: [PATCH 2/4] irqchip/fsl-mc: Change the way the IRQ domain is set for
MC devices
Content-Type: text/plain; charset="us-ascii"
In ACPI the MC bus is represented as a platform device and a named
component in the IORT table. The mc-bus devices are discovered
dynamically at runtime but they share the same fwnode with the parent
platfom device. This patch changes the way the IRQ domain is searched
for the MC devices: it takes the fwnode reference from the parent and
uses the fwnode reference to find the MC IRQ domain.
Signed-off-by: Diana Craciun <diana.craciun@oss.nxp.com>
---
drivers/bus/fsl-mc/fsl-mc-msi.c | 11 +++++++++--
1 file changed, 9 insertions(+), 2 deletions(-)
diff --git a/drivers/bus/fsl-mc/fsl-mc-msi.c b/drivers/bus/fsl-mc/fsl-mc-msi.c
index 8b9c66d7c4ff..1e2e97329781 100644
--- a/drivers/bus/fsl-mc/fsl-mc-msi.c
+++ b/drivers/bus/fsl-mc/fsl-mc-msi.c
@@ -182,16 +182,23 @@ int fsl_mc_find_msi_domain(struct device *mc_platform_dev,
{
struct irq_domain *msi_domain;
struct device_node *mc_of_node = mc_platform_dev->of_node;
+ struct fwnode_handle *fwnode;
- msi_domain = of_msi_get_domain(mc_platform_dev, mc_of_node,
- DOMAIN_BUS_FSL_MC_MSI);
+ msi_domain = dev_get_msi_domain(mc_platform_dev);
if (!msi_domain) {
pr_err("Unable to find fsl-mc MSI domain for %pOF\n",
mc_of_node);
return -ENOENT;
}
+ fwnode = msi_domain->fwnode;
+ msi_domain = irq_find_matching_fwnode(fwnode, DOMAIN_BUS_FSL_MC_MSI);
+ if (!msi_domain) {
+ pr_err("Unable to find fsl-mc MSI domain for %pOF\n",
+ mc_of_node);
+ return -ENOENT;
+ }
*mc_msi_domain = msi_domain;
return 0;
}
--
2.17.1
[-- Attachment #4: 0003-bus-fsl-mc-Add-ACPI-support-for-fsl-mc.patch --]
[-- Type: text/x-patch, Size: 6022 bytes --]
From 29d5565744a3c16b93bd6d029368cf39996c69f3 Mon Sep 17 00:00:00 2001
From: Makarand Pawagi <makarand.pawagi@nxp.com>
Date: Thu, 23 Jan 2020 10:48:42 +0530
Subject: [PATCH 3/4] bus: fsl-mc: Add ACPI support for fsl-mc
Content-Type: text/plain; charset="us-ascii"
ACPI support is added in the fsl-mc driver. Driver will parse
MC DSDT table to extract memory and other resorces.
Interrupt (GIC ITS) information will be extracted from MADT table
by drivers/irqchip/irq-gic-v3-its-fsl-mc-msi.c.
IORT table will be parsed to configure DMA.
Signed-off-by: Makarand Pawagi <makarand.pawagi@nxp.com>
---
drivers/bus/fsl-mc/fsl-mc-bus.c | 35 ++++++-----
drivers/irqchip/irq-gic-v3-its-fsl-mc-msi.c | 69 ++++++++++++++++++++-
2 files changed, 87 insertions(+), 17 deletions(-)
diff --git a/drivers/bus/fsl-mc/fsl-mc-bus.c b/drivers/bus/fsl-mc/fsl-mc-bus.c
index 3df015eedae4..742f3563c775 100644
--- a/drivers/bus/fsl-mc/fsl-mc-bus.c
+++ b/drivers/bus/fsl-mc/fsl-mc-bus.c
@@ -952,7 +952,7 @@ static int fsl_mc_bus_probe(struct platform_device *pdev)
phys_addr_t mc_portal_phys_addr;
u32 mc_portal_size;
struct mc_version mc_version;
- struct resource res;
+ struct resource *plat_res;
/*
* The MC firmware requires full access to the whole address space plus
@@ -978,16 +978,9 @@ static int fsl_mc_bus_probe(struct platform_device *pdev)
/*
* Get physical address of MC portal for the root DPRC:
*/
- error = of_address_to_resource(pdev->dev.of_node, 0, &res);
- if (error < 0) {
- dev_err(&pdev->dev,
- "of_address_to_resource() failed for %pOF\n",
- pdev->dev.of_node);
- return error;
- }
-
- mc_portal_phys_addr = res.start;
- mc_portal_size = resource_size(&res);
+ plat_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ mc_portal_phys_addr = plat_res->start;
+ mc_portal_size = resource_size(plat_res);
error = fsl_create_mc_io(&pdev->dev, mc_portal_phys_addr,
mc_portal_size, NULL,
FSL_MC_IO_ATOMIC_CONTEXT_PORTAL, &mc_io);
@@ -1004,11 +997,13 @@ static int fsl_mc_bus_probe(struct platform_device *pdev)
dev_info(&pdev->dev, "MC firmware version: %u.%u.%u\n",
mc_version.major, mc_version.minor, mc_version.revision);
- error = get_mc_addr_translation_ranges(&pdev->dev,
- &mc->translation_ranges,
- &mc->num_translation_ranges);
- if (error < 0)
- goto error_cleanup_mc_io;
+ if (dev_of_node(&pdev->dev)) {
+ error = get_mc_addr_translation_ranges(&pdev->dev,
+ &mc->translation_ranges,
+ &mc->num_translation_ranges);
+ if (error < 0)
+ goto error_cleanup_mc_io;
+ }
error = dprc_get_container_id(mc_io, 0, &container_id);
if (error < 0) {
@@ -1035,6 +1030,7 @@ static int fsl_mc_bus_probe(struct platform_device *pdev)
goto error_cleanup_mc_io;
mc->root_mc_bus_dev = mc_bus_dev;
+ mc_bus_dev->dev.fwnode = pdev->dev.fwnode;
return 0;
error_cleanup_mc_io:
@@ -1075,11 +1071,18 @@ static const struct of_device_id fsl_mc_bus_match_table[] = {
MODULE_DEVICE_TABLE(of, fsl_mc_bus_match_table);
+static const struct acpi_device_id fsl_mc_bus_acpi_match_table[] = {
+ {"NXP0008", 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(acpi, fsl_mc_bus_acpi_match_table);
+
static struct platform_driver fsl_mc_bus_driver = {
.driver = {
.name = "fsl_mc_bus",
.pm = NULL,
.of_match_table = fsl_mc_bus_match_table,
+ .acpi_match_table = fsl_mc_bus_acpi_match_table,
},
.probe = fsl_mc_bus_probe,
.remove = fsl_mc_bus_remove,
diff --git a/drivers/irqchip/irq-gic-v3-its-fsl-mc-msi.c b/drivers/irqchip/irq-gic-v3-its-fsl-mc-msi.c
index 606efa64adff..6d67834722c9 100644
--- a/drivers/irqchip/irq-gic-v3-its-fsl-mc-msi.c
+++ b/drivers/irqchip/irq-gic-v3-its-fsl-mc-msi.c
@@ -4,9 +4,11 @@
*
* Copyright (C) 2015-2016 Freescale Semiconductor, Inc.
* Author: German Rivera <German.Rivera@freescale.com>
+ * Copyright 2020 NXP
*
*/
+#include <linux/acpi_iort.h>
#include <linux/of_device.h>
#include <linux/of_address.h>
#include <linux/irq.h>
@@ -66,7 +68,65 @@ static const struct of_device_id its_device_id[] = {
{},
};
-static int __init its_fsl_mc_msi_init(void)
+static int __init its_fsl_mc_msi_init_one(struct fwnode_handle *handle,
+ const char *name)
+{
+ struct irq_domain *parent;
+ struct irq_domain *mc_msi_domain;
+
+ parent = irq_find_matching_fwnode(handle, DOMAIN_BUS_NEXUS);
+ if (!parent || !msi_get_domain_info(parent)) {
+ pr_err("%s: Unable to locate ITS domain\n", name);
+ return -ENXIO;
+ }
+
+ mc_msi_domain = fsl_mc_msi_create_irq_domain(handle,
+ &its_fsl_mc_msi_domain_info,
+ parent);
+ if (!mc_msi_domain)
+ pr_err("ACPIF: unable to create fsl-mc domain\n");
+
+ pr_info("fsl-mc MSI: domain created\n");
+
+ return 0;
+}
+
+static int __init
+its_fsl_mc_msi_parse_madt(union acpi_subtable_headers *header,
+ const unsigned long end)
+{
+ struct acpi_madt_generic_translator *its_entry;
+ struct fwnode_handle *dom_handle;
+ const char *node_name;
+ int err = -ENXIO;
+
+ its_entry = (struct acpi_madt_generic_translator *)header;
+ node_name = kasprintf(GFP_KERNEL, "ITS@0x%lx",
+ (long)its_entry->base_address);
+
+ dom_handle = iort_find_domain_token(its_entry->translation_id);
+ if (!dom_handle) {
+ pr_err("%s: Unable to locate ITS domain handle\n", node_name);
+ goto out;
+ }
+
+ err = its_fsl_mc_msi_init_one(dom_handle, node_name);
+ if (!err)
+ pr_info("fsl-mc MSI: %s domain created\n", node_name);
+
+out:
+ kfree(node_name);
+ return err;
+}
+
+static int __init its_fsl_mc_acpi_msi_init(void)
+{
+ acpi_table_parse_madt(ACPI_MADT_TYPE_GENERIC_TRANSLATOR,
+ its_fsl_mc_msi_parse_madt, 0);
+ return 0;
+}
+
+static int __init its_fsl_mc_of_msi_init(void)
{
struct device_node *np;
struct irq_domain *parent;
@@ -100,4 +160,11 @@ static int __init its_fsl_mc_msi_init(void)
return 0;
}
+static int __init its_fsl_mc_msi_init(void)
+{
+ its_fsl_mc_of_msi_init();
+ its_fsl_mc_acpi_msi_init();
+
+ return 0;
+}
early_initcall(its_fsl_mc_msi_init);
--
2.17.1
[-- Attachment #5: 0004-iommu-of-get-rid-of-fsl-mc-specific-code.patch --]
[-- Type: text/x-patch, Size: 1897 bytes --]
From fe4f961f3c5dbe20c66a238a1520fc09b13e8c9e Mon Sep 17 00:00:00 2001
From: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Date: Wed, 26 Feb 2020 17:31:49 +0200
Subject: [PATCH 4/4] iommu/of: get rid of fsl-mc specific code
Content-Type: text/plain; charset="us-ascii"
Changing the way we configure dma for fsl-mc devices allows
us to get rid of our fsl-mc specific code in the generic
of iommu code.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
---
drivers/iommu/of_iommu.c | 20 --------------------
1 file changed, 20 deletions(-)
diff --git a/drivers/iommu/of_iommu.c b/drivers/iommu/of_iommu.c
index 20738aacac89..332072ada474 100644
--- a/drivers/iommu/of_iommu.c
+++ b/drivers/iommu/of_iommu.c
@@ -15,7 +15,6 @@
#include <linux/of_pci.h>
#include <linux/pci.h>
#include <linux/slab.h>
-#include <linux/fsl/mc.h>
#define NO_IOMMU 1
@@ -139,23 +138,6 @@ static int of_pci_iommu_init(struct pci_dev *pdev, u16 alias, void *data)
return err;
}
-static int of_fsl_mc_iommu_init(struct fsl_mc_device *mc_dev,
- struct device_node *master_np)
-{
- struct of_phandle_args iommu_spec = { .args_count = 1 };
- int err;
-
- err = of_map_rid(master_np, mc_dev->icid, "iommu-map",
- "iommu-map-mask", &iommu_spec.np,
- iommu_spec.args);
- if (err)
- return err == -ENODEV ? NO_IOMMU : err;
-
- err = of_iommu_xlate(&mc_dev->dev, &iommu_spec);
- of_node_put(iommu_spec.np);
- return err;
-}
-
const struct iommu_ops *of_iommu_configure(struct device *dev,
struct device_node *master_np)
{
@@ -188,8 +170,6 @@ const struct iommu_ops *of_iommu_configure(struct device *dev,
pci_request_acs();
err = pci_for_each_dma_alias(to_pci_dev(dev),
of_pci_iommu_init, &info);
- } else if (dev_is_fsl_mc(dev)) {
- err = of_fsl_mc_iommu_init(to_fsl_mc_device(dev), master_np);
} else {
struct of_phandle_args iommu_spec;
int idx = 0;
--
2.17.1
[-- Attachment #6: Type: text/plain, Size: 156 bytes --]
_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu
^ permalink raw reply related [flat|nested] 24+ messages in thread
* Re: [PATCH] iommu: silence iommu group prints
2020-03-03 15:55 ` Laurentiu Tudor
@ 2020-03-03 22:17 ` Russell King - ARM Linux admin
2020-03-04 8:56 ` Laurentiu Tudor
0 siblings, 1 reply; 24+ messages in thread
From: Russell King - ARM Linux admin @ 2020-03-03 22:17 UTC (permalink / raw)
To: Laurentiu Tudor
Cc: Diana Madalina Craciun, iommu, Robin Murphy, Ioana Ciornei
On Tue, Mar 03, 2020 at 05:55:05PM +0200, Laurentiu Tudor wrote:
> From c98dc05cdd45ae923654f2427985bd28bcde4bb2 Mon Sep 17 00:00:00 2001
> From: Laurentiu Tudor <laurentiu.tudor@nxp.com>
> Date: Thu, 13 Feb 2020 11:59:12 +0200
> Subject: [PATCH 1/4] bus: fsl-mc: add custom .dma_configure implementation
> Content-Type: text/plain; charset="us-ascii"
>
> The devices on this bus are not discovered by way of device tree
> but by queries to the firmware. It makes little sense to trick the
> generic of layer into thinking that these devices are of related so
> that we can get our dma configuration. Instead of doing that, add
> our custom dma configuration implementation.
Firstly, applying this to v5.5 results in a build failure, due to a
missing linux/iommu.h include.
Secondly, this on its own appears to make the DPAA2 network interfaces
completely disappear. Looking in /sys/bus/fsl-mc/drivers/*, none of
the DPAA2 drivers are bound to anything, and looking in
/sys/bus/fsl-mc/devices/, there is:
lrwxrwxrwx 1 root root 0 Mar 3 22:06 dprc.1 -> ../../../devices/platform/soc/80c000000.fsl-mc/dprc.1
This is booting with u-boot, so using DT rather than ACPI.
> Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
> ---
> drivers/bus/fsl-mc/fsl-mc-bus.c | 42 ++++++++++++++++++++++++++++++++-
> 1 file changed, 41 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/bus/fsl-mc/fsl-mc-bus.c b/drivers/bus/fsl-mc/fsl-mc-bus.c
> index 36eb25f82c8e..3df015eedae4 100644
> --- a/drivers/bus/fsl-mc/fsl-mc-bus.c
> +++ b/drivers/bus/fsl-mc/fsl-mc-bus.c
> @@ -132,11 +132,51 @@ static int fsl_mc_bus_uevent(struct device *dev, struct kobj_uevent_env *env)
> static int fsl_mc_dma_configure(struct device *dev)
> {
> struct device *dma_dev = dev;
> + struct iommu_fwspec *fwspec;
> + const struct iommu_ops *iommu_ops;
> + struct fsl_mc_device *mc_dev = to_fsl_mc_device(dev);
> + int ret;
> + u32 icid;
> +
> + /* Skip DMA setup for devices that are not DMA masters */
> + if (dev->type == &fsl_mc_bus_dpmcp_type ||
> + dev->type == &fsl_mc_bus_dpbp_type ||
> + dev->type == &fsl_mc_bus_dpcon_type ||
> + dev->type == &fsl_mc_bus_dpio_type)
> + return 0;
>
> while (dev_is_fsl_mc(dma_dev))
> dma_dev = dma_dev->parent;
>
> - return of_dma_configure(dev, dma_dev->of_node, 0);
> + fwspec = dev_iommu_fwspec_get(dma_dev);
> + if (!fwspec)
> + return -ENODEV;
The problem appears to be here - fwspec is NULL for dprc.1.
> + iommu_ops = iommu_ops_from_fwnode(fwspec->iommu_fwnode);
> + if (!iommu_ops)
> + return -ENODEV;
> +
> + ret = iommu_fwspec_init(dev, fwspec->iommu_fwnode, iommu_ops);
> + if (ret)
> + return ret;
> +
> + icid = mc_dev->icid;
> + ret = iommu_fwspec_add_ids(dev, &icid, 1);
> + if (ret) {
> + iommu_fwspec_free(dev);
> + return ret;
> + }
> +
> + if (!device_iommu_mapped(dev)) {
> + ret = iommu_probe_device(dev);
> + if (ret) {
> + iommu_fwspec_free(dev);
> + return ret;
> + }
> + }
> +
> + arch_setup_dma_ops(dev, 0, *dma_dev->dma_mask + 1, iommu_ops, true);
> +
> + return 0;
> }
>
> static ssize_t modalias_show(struct device *dev, struct device_attribute *attr,
> --
> 2.17.1
>
--
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up
According to speedtest.net: 11.9Mbps down 500kbps up
_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH] iommu: silence iommu group prints
2020-03-03 22:17 ` Russell King - ARM Linux admin
@ 2020-03-04 8:56 ` Laurentiu Tudor
2020-03-04 9:33 ` Russell King - ARM Linux admin
0 siblings, 1 reply; 24+ messages in thread
From: Laurentiu Tudor @ 2020-03-04 8:56 UTC (permalink / raw)
To: Russell King - ARM Linux admin
Cc: Diana Madalina Craciun, iommu, Robin Murphy, Ioana Ciornei
[-- Attachment #1: Type: text/plain, Size: 2940 bytes --]
On 04.03.2020 00:17, Russell King - ARM Linux admin wrote:
> On Tue, Mar 03, 2020 at 05:55:05PM +0200, Laurentiu Tudor wrote:
>> From c98dc05cdd45ae923654f2427985bd28bcde4bb2 Mon Sep 17 00:00:00 2001
>> From: Laurentiu Tudor <laurentiu.tudor@nxp.com>
>> Date: Thu, 13 Feb 2020 11:59:12 +0200
>> Subject: [PATCH 1/4] bus: fsl-mc: add custom .dma_configure implementation
>> Content-Type: text/plain; charset="us-ascii"
>>
>> The devices on this bus are not discovered by way of device tree
>> but by queries to the firmware. It makes little sense to trick the
>> generic of layer into thinking that these devices are of related so
>> that we can get our dma configuration. Instead of doing that, add
>> our custom dma configuration implementation.
>
> Firstly, applying this to v5.5 results in a build failure, due to a
> missing linux/iommu.h include.
>
> Secondly, this on its own appears to make the DPAA2 network interfaces
> completely disappear. Looking in /sys/bus/fsl-mc/drivers/*, none of
> the DPAA2 drivers are bound to anything, and looking in
> /sys/bus/fsl-mc/devices/, there is:
>
> lrwxrwxrwx 1 root root 0 Mar 3 22:06 dprc.1 -> ../../../devices/platform/soc/80c000000.fsl-mc/dprc.1
>
> This is booting with u-boot, so using DT rather than ACPI.
>
>> Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
>> ---
>> drivers/bus/fsl-mc/fsl-mc-bus.c | 42 ++++++++++++++++++++++++++++++++-
>> 1 file changed, 41 insertions(+), 1 deletion(-)
>>
>> diff --git a/drivers/bus/fsl-mc/fsl-mc-bus.c b/drivers/bus/fsl-mc/fsl-mc-bus.c
>> index 36eb25f82c8e..3df015eedae4 100644
>> --- a/drivers/bus/fsl-mc/fsl-mc-bus.c
>> +++ b/drivers/bus/fsl-mc/fsl-mc-bus.c
>> @@ -132,11 +132,51 @@ static int fsl_mc_bus_uevent(struct device *dev, struct kobj_uevent_env *env)
>> static int fsl_mc_dma_configure(struct device *dev)
>> {
>> struct device *dma_dev = dev;
>> + struct iommu_fwspec *fwspec;
>> + const struct iommu_ops *iommu_ops;
>> + struct fsl_mc_device *mc_dev = to_fsl_mc_device(dev);
>> + int ret;
>> + u32 icid;
>> +
>> + /* Skip DMA setup for devices that are not DMA masters */
>> + if (dev->type == &fsl_mc_bus_dpmcp_type ||
>> + dev->type == &fsl_mc_bus_dpbp_type ||
>> + dev->type == &fsl_mc_bus_dpcon_type ||
>> + dev->type == &fsl_mc_bus_dpio_type)
>> + return 0;
>>
>> while (dev_is_fsl_mc(dma_dev))
>> dma_dev = dma_dev->parent;
>>
>> - return of_dma_configure(dev, dma_dev->of_node, 0);
>> + fwspec = dev_iommu_fwspec_get(dma_dev);
>> + if (!fwspec)
>> + return -ENODEV;
>
> The problem appears to be here - fwspec is NULL for dprc.1.
Ok, that's because the iommu config is missing from the DT node that's
exposing the MC firmware. I've attached a fresh set of patches that
include on top the missing config and a workaround that makes MC work
over SMMU. Also added the missing #include, thanks for pointing out.
Let me know how it goes.
---
Best Regards, Laurentiu
[-- Attachment #2: 0001-bus-fsl-mc-add-custom-.dma_configure-implementation.patch --]
[-- Type: text/x-patch, Size: 2551 bytes --]
From 3d418f04fed9c10b64b3b861d66378a8f7514cc4 Mon Sep 17 00:00:00 2001
From: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Date: Thu, 13 Feb 2020 11:59:12 +0200
Subject: [PATCH 1/6] bus: fsl-mc: add custom .dma_configure implementation
Content-Type: text/plain; charset="us-ascii"
The devices on this bus are not discovered by way of device tree
but by queries to the firmware. It makes little sense to trick the
generic of layer into thinking that these devices are of related so
that we can get our dma configuration. Instead of doing that, add
our custom dma configuration implementation.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
---
drivers/bus/fsl-mc/fsl-mc-bus.c | 43 ++++++++++++++++++++++++++++++++-
1 file changed, 42 insertions(+), 1 deletion(-)
diff --git a/drivers/bus/fsl-mc/fsl-mc-bus.c b/drivers/bus/fsl-mc/fsl-mc-bus.c
index a0f8854acb3a..e2682fbefb42 100644
--- a/drivers/bus/fsl-mc/fsl-mc-bus.c
+++ b/drivers/bus/fsl-mc/fsl-mc-bus.c
@@ -18,6 +18,7 @@
#include <linux/bitops.h>
#include <linux/msi.h>
#include <linux/dma-mapping.h>
+#include <linux/iommu.h>
#include "fsl-mc-private.h"
@@ -130,11 +131,51 @@ static int fsl_mc_bus_uevent(struct device *dev, struct kobj_uevent_env *env)
static int fsl_mc_dma_configure(struct device *dev)
{
struct device *dma_dev = dev;
+ struct iommu_fwspec *fwspec;
+ const struct iommu_ops *iommu_ops;
+ struct fsl_mc_device *mc_dev = to_fsl_mc_device(dev);
+ int ret;
+ u32 icid;
+
+ /* Skip DMA setup for devices that are not DMA masters */
+ if (dev->type == &fsl_mc_bus_dpmcp_type ||
+ dev->type == &fsl_mc_bus_dpbp_type ||
+ dev->type == &fsl_mc_bus_dpcon_type ||
+ dev->type == &fsl_mc_bus_dpio_type)
+ return 0;
while (dev_is_fsl_mc(dma_dev))
dma_dev = dma_dev->parent;
- return of_dma_configure(dev, dma_dev->of_node, 0);
+ fwspec = dev_iommu_fwspec_get(dma_dev);
+ if (!fwspec)
+ return -ENODEV;
+ iommu_ops = iommu_ops_from_fwnode(fwspec->iommu_fwnode);
+ if (!iommu_ops)
+ return -ENODEV;
+
+ ret = iommu_fwspec_init(dev, fwspec->iommu_fwnode, iommu_ops);
+ if (ret)
+ return ret;
+
+ icid = mc_dev->icid;
+ ret = iommu_fwspec_add_ids(dev, &icid, 1);
+ if (ret) {
+ iommu_fwspec_free(dev);
+ return ret;
+ }
+
+ if (!device_iommu_mapped(dev)) {
+ ret = iommu_probe_device(dev);
+ if (ret) {
+ iommu_fwspec_free(dev);
+ return ret;
+ }
+ }
+
+ arch_setup_dma_ops(dev, 0, *dma_dev->dma_mask + 1, iommu_ops, true);
+
+ return 0;
}
static ssize_t modalias_show(struct device *dev, struct device_attribute *attr,
--
2.17.1
[-- Attachment #3: 0002-irqchip-fsl-mc-Change-the-way-the-IRQ-domain-is-set-.patch --]
[-- Type: text/x-patch, Size: 1818 bytes --]
From 8b7576f002fab8471e907621a4debbdfb5635101 Mon Sep 17 00:00:00 2001
From: Diana Craciun <diana.craciun@oss.nxp.com>
Date: Fri, 14 Feb 2020 16:28:45 +0200
Subject: [PATCH 2/6] irqchip/fsl-mc: Change the way the IRQ domain is set for
MC devices
Content-Type: text/plain; charset="us-ascii"
In ACPI the MC bus is represented as a platform device and a named
component in the IORT table. The mc-bus devices are discovered
dynamically at runtime but they share the same fwnode with the parent
platfom device. This patch changes the way the IRQ domain is searched
for the MC devices: it takes the fwnode reference from the parent and
uses the fwnode reference to find the MC IRQ domain.
Signed-off-by: Diana Craciun <diana.craciun@oss.nxp.com>
---
drivers/bus/fsl-mc/fsl-mc-msi.c | 11 +++++++++--
1 file changed, 9 insertions(+), 2 deletions(-)
diff --git a/drivers/bus/fsl-mc/fsl-mc-msi.c b/drivers/bus/fsl-mc/fsl-mc-msi.c
index 8b9c66d7c4ff..1e2e97329781 100644
--- a/drivers/bus/fsl-mc/fsl-mc-msi.c
+++ b/drivers/bus/fsl-mc/fsl-mc-msi.c
@@ -182,16 +182,23 @@ int fsl_mc_find_msi_domain(struct device *mc_platform_dev,
{
struct irq_domain *msi_domain;
struct device_node *mc_of_node = mc_platform_dev->of_node;
+ struct fwnode_handle *fwnode;
- msi_domain = of_msi_get_domain(mc_platform_dev, mc_of_node,
- DOMAIN_BUS_FSL_MC_MSI);
+ msi_domain = dev_get_msi_domain(mc_platform_dev);
if (!msi_domain) {
pr_err("Unable to find fsl-mc MSI domain for %pOF\n",
mc_of_node);
return -ENOENT;
}
+ fwnode = msi_domain->fwnode;
+ msi_domain = irq_find_matching_fwnode(fwnode, DOMAIN_BUS_FSL_MC_MSI);
+ if (!msi_domain) {
+ pr_err("Unable to find fsl-mc MSI domain for %pOF\n",
+ mc_of_node);
+ return -ENOENT;
+ }
*mc_msi_domain = msi_domain;
return 0;
}
--
2.17.1
[-- Attachment #4: 0003-bus-fsl-mc-Add-ACPI-support-for-fsl-mc.patch --]
[-- Type: text/x-patch, Size: 6011 bytes --]
From f63813721d58059ee52b38bdd5b584694e9205cd Mon Sep 17 00:00:00 2001
From: Makarand Pawagi <makarand.pawagi@nxp.com>
Date: Thu, 23 Jan 2020 10:48:42 +0530
Subject: [PATCH 3/6] bus: fsl-mc: Add ACPI support for fsl-mc
Content-Type: text/plain; charset="us-ascii"
ACPI support is added in the fsl-mc driver. Driver will parse
MC DSDT table to extract memory and other resorces.
Interrupt (GIC ITS) information will be extracted from MADT table
by drivers/irqchip/irq-gic-v3-its-fsl-mc-msi.c.
IORT table will be parsed to configure DMA.
Signed-off-by: Makarand Pawagi <makarand.pawagi@nxp.com>
---
drivers/bus/fsl-mc/fsl-mc-bus.c | 35 ++++++-----
drivers/irqchip/irq-gic-v3-its-fsl-mc-msi.c | 69 ++++++++++++++++++++-
2 files changed, 87 insertions(+), 17 deletions(-)
diff --git a/drivers/bus/fsl-mc/fsl-mc-bus.c b/drivers/bus/fsl-mc/fsl-mc-bus.c
index e2682fbefb42..485a70b7360d 100644
--- a/drivers/bus/fsl-mc/fsl-mc-bus.c
+++ b/drivers/bus/fsl-mc/fsl-mc-bus.c
@@ -945,7 +945,7 @@ static int fsl_mc_bus_probe(struct platform_device *pdev)
phys_addr_t mc_portal_phys_addr;
u32 mc_portal_size;
struct mc_version mc_version;
- struct resource res;
+ struct resource *plat_res;
mc = devm_kzalloc(&pdev->dev, sizeof(*mc), GFP_KERNEL);
if (!mc)
@@ -956,16 +956,9 @@ static int fsl_mc_bus_probe(struct platform_device *pdev)
/*
* Get physical address of MC portal for the root DPRC:
*/
- error = of_address_to_resource(pdev->dev.of_node, 0, &res);
- if (error < 0) {
- dev_err(&pdev->dev,
- "of_address_to_resource() failed for %pOF\n",
- pdev->dev.of_node);
- return error;
- }
-
- mc_portal_phys_addr = res.start;
- mc_portal_size = resource_size(&res);
+ plat_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ mc_portal_phys_addr = plat_res->start;
+ mc_portal_size = resource_size(plat_res);
error = fsl_create_mc_io(&pdev->dev, mc_portal_phys_addr,
mc_portal_size, NULL,
FSL_MC_IO_ATOMIC_CONTEXT_PORTAL, &mc_io);
@@ -982,11 +975,13 @@ static int fsl_mc_bus_probe(struct platform_device *pdev)
dev_info(&pdev->dev, "MC firmware version: %u.%u.%u\n",
mc_version.major, mc_version.minor, mc_version.revision);
- error = get_mc_addr_translation_ranges(&pdev->dev,
- &mc->translation_ranges,
- &mc->num_translation_ranges);
- if (error < 0)
- goto error_cleanup_mc_io;
+ if (dev_of_node(&pdev->dev)) {
+ error = get_mc_addr_translation_ranges(&pdev->dev,
+ &mc->translation_ranges,
+ &mc->num_translation_ranges);
+ if (error < 0)
+ goto error_cleanup_mc_io;
+ }
error = dprc_get_container_id(mc_io, 0, &container_id);
if (error < 0) {
@@ -1013,6 +1008,7 @@ static int fsl_mc_bus_probe(struct platform_device *pdev)
goto error_cleanup_mc_io;
mc->root_mc_bus_dev = mc_bus_dev;
+ mc_bus_dev->dev.fwnode = pdev->dev.fwnode;
return 0;
error_cleanup_mc_io:
@@ -1046,11 +1042,18 @@ static const struct of_device_id fsl_mc_bus_match_table[] = {
MODULE_DEVICE_TABLE(of, fsl_mc_bus_match_table);
+static const struct acpi_device_id fsl_mc_bus_acpi_match_table[] = {
+ {"NXP0008", 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(acpi, fsl_mc_bus_acpi_match_table);
+
static struct platform_driver fsl_mc_bus_driver = {
.driver = {
.name = "fsl_mc_bus",
.pm = NULL,
.of_match_table = fsl_mc_bus_match_table,
+ .acpi_match_table = fsl_mc_bus_acpi_match_table,
},
.probe = fsl_mc_bus_probe,
.remove = fsl_mc_bus_remove,
diff --git a/drivers/irqchip/irq-gic-v3-its-fsl-mc-msi.c b/drivers/irqchip/irq-gic-v3-its-fsl-mc-msi.c
index 606efa64adff..6d67834722c9 100644
--- a/drivers/irqchip/irq-gic-v3-its-fsl-mc-msi.c
+++ b/drivers/irqchip/irq-gic-v3-its-fsl-mc-msi.c
@@ -4,9 +4,11 @@
*
* Copyright (C) 2015-2016 Freescale Semiconductor, Inc.
* Author: German Rivera <German.Rivera@freescale.com>
+ * Copyright 2020 NXP
*
*/
+#include <linux/acpi_iort.h>
#include <linux/of_device.h>
#include <linux/of_address.h>
#include <linux/irq.h>
@@ -66,7 +68,65 @@ static const struct of_device_id its_device_id[] = {
{},
};
-static int __init its_fsl_mc_msi_init(void)
+static int __init its_fsl_mc_msi_init_one(struct fwnode_handle *handle,
+ const char *name)
+{
+ struct irq_domain *parent;
+ struct irq_domain *mc_msi_domain;
+
+ parent = irq_find_matching_fwnode(handle, DOMAIN_BUS_NEXUS);
+ if (!parent || !msi_get_domain_info(parent)) {
+ pr_err("%s: Unable to locate ITS domain\n", name);
+ return -ENXIO;
+ }
+
+ mc_msi_domain = fsl_mc_msi_create_irq_domain(handle,
+ &its_fsl_mc_msi_domain_info,
+ parent);
+ if (!mc_msi_domain)
+ pr_err("ACPIF: unable to create fsl-mc domain\n");
+
+ pr_info("fsl-mc MSI: domain created\n");
+
+ return 0;
+}
+
+static int __init
+its_fsl_mc_msi_parse_madt(union acpi_subtable_headers *header,
+ const unsigned long end)
+{
+ struct acpi_madt_generic_translator *its_entry;
+ struct fwnode_handle *dom_handle;
+ const char *node_name;
+ int err = -ENXIO;
+
+ its_entry = (struct acpi_madt_generic_translator *)header;
+ node_name = kasprintf(GFP_KERNEL, "ITS@0x%lx",
+ (long)its_entry->base_address);
+
+ dom_handle = iort_find_domain_token(its_entry->translation_id);
+ if (!dom_handle) {
+ pr_err("%s: Unable to locate ITS domain handle\n", node_name);
+ goto out;
+ }
+
+ err = its_fsl_mc_msi_init_one(dom_handle, node_name);
+ if (!err)
+ pr_info("fsl-mc MSI: %s domain created\n", node_name);
+
+out:
+ kfree(node_name);
+ return err;
+}
+
+static int __init its_fsl_mc_acpi_msi_init(void)
+{
+ acpi_table_parse_madt(ACPI_MADT_TYPE_GENERIC_TRANSLATOR,
+ its_fsl_mc_msi_parse_madt, 0);
+ return 0;
+}
+
+static int __init its_fsl_mc_of_msi_init(void)
{
struct device_node *np;
struct irq_domain *parent;
@@ -100,4 +160,11 @@ static int __init its_fsl_mc_msi_init(void)
return 0;
}
+static int __init its_fsl_mc_msi_init(void)
+{
+ its_fsl_mc_of_msi_init();
+ its_fsl_mc_acpi_msi_init();
+
+ return 0;
+}
early_initcall(its_fsl_mc_msi_init);
--
2.17.1
[-- Attachment #5: 0004-iommu-of-get-rid-of-fsl-mc-specific-code.patch --]
[-- Type: text/x-patch, Size: 1897 bytes --]
From 268e57107bcc31cec9722382326bd282985eb4c7 Mon Sep 17 00:00:00 2001
From: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Date: Wed, 26 Feb 2020 17:31:49 +0200
Subject: [PATCH 4/6] iommu/of: get rid of fsl-mc specific code
Content-Type: text/plain; charset="us-ascii"
Changing the way we configure dma for fsl-mc devices allows
us to get rid of our fsl-mc specific code in the generic
of iommu code.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
---
drivers/iommu/of_iommu.c | 20 --------------------
1 file changed, 20 deletions(-)
diff --git a/drivers/iommu/of_iommu.c b/drivers/iommu/of_iommu.c
index 20738aacac89..332072ada474 100644
--- a/drivers/iommu/of_iommu.c
+++ b/drivers/iommu/of_iommu.c
@@ -15,7 +15,6 @@
#include <linux/of_pci.h>
#include <linux/pci.h>
#include <linux/slab.h>
-#include <linux/fsl/mc.h>
#define NO_IOMMU 1
@@ -139,23 +138,6 @@ static int of_pci_iommu_init(struct pci_dev *pdev, u16 alias, void *data)
return err;
}
-static int of_fsl_mc_iommu_init(struct fsl_mc_device *mc_dev,
- struct device_node *master_np)
-{
- struct of_phandle_args iommu_spec = { .args_count = 1 };
- int err;
-
- err = of_map_rid(master_np, mc_dev->icid, "iommu-map",
- "iommu-map-mask", &iommu_spec.np,
- iommu_spec.args);
- if (err)
- return err == -ENODEV ? NO_IOMMU : err;
-
- err = of_iommu_xlate(&mc_dev->dev, &iommu_spec);
- of_node_put(iommu_spec.np);
- return err;
-}
-
const struct iommu_ops *of_iommu_configure(struct device *dev,
struct device_node *master_np)
{
@@ -188,8 +170,6 @@ const struct iommu_ops *of_iommu_configure(struct device *dev,
pci_request_acs();
err = pci_for_each_dma_alias(to_pci_dev(dev),
of_pci_iommu_init, &info);
- } else if (dev_is_fsl_mc(dev)) {
- err = of_fsl_mc_iommu_init(to_fsl_mc_device(dev), master_np);
} else {
struct of_phandle_args iommu_spec;
int idx = 0;
--
2.17.1
[-- Attachment #6: 0005-bus-fsl-mc-make-mc-work-with-smmu-disable-bypass-on.patch --]
[-- Type: text/x-patch, Size: 4144 bytes --]
From 68abcd76ce8cd1c368a4b7ee45f72f02b80c33b3 Mon Sep 17 00:00:00 2001
From: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Date: Tue, 1 Oct 2019 16:22:48 +0300
Subject: [PATCH 5/6] bus: fsl-mc: make mc work with smmu disable bypass on
Content-Type: text/plain; charset="us-ascii"
Since this commit [1] booting kernel on MC based chips started to
fail because this firmware starts before the kernel and as soon as
SMMU is probed it starts to trigger contiguous faults.
This is a workaround that allows MC firmware to run with SMMU
in disable bypass mode. It consists of the following steps:
1. pause the firmware at early boot to get a chance to setup SMMU
2. request direct mapping for MC device
3. resume the firmware
The workaround relies on the fact that no state is lost when
pausing / resuming firmware, as per the docs.
With this patch, platforms with MC firmware can now boot without
having to change the default config to set:
CONFIG_ARM_SMMU_DISABLE_BYPASS_BY_DEFAULT=n
[1] 954a03be033 ("iommu/arm-smmu: Break insecure users by disabling bypass by default")
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
---
drivers/bus/fsl-mc/fsl-mc-bus.c | 52 +++++++++++++++++++++++++++++++++
1 file changed, 52 insertions(+)
diff --git a/drivers/bus/fsl-mc/fsl-mc-bus.c b/drivers/bus/fsl-mc/fsl-mc-bus.c
index 485a70b7360d..8a385df3e25c 100644
--- a/drivers/bus/fsl-mc/fsl-mc-bus.c
+++ b/drivers/bus/fsl-mc/fsl-mc-bus.c
@@ -19,6 +19,7 @@
#include <linux/msi.h>
#include <linux/dma-mapping.h>
#include <linux/iommu.h>
+#include <linux/io.h>
#include "fsl-mc-private.h"
@@ -930,6 +931,12 @@ static int get_mc_addr_translation_ranges(struct device *dev,
return 0;
}
+#define FSL_MC_GCR1 0x0
+#define GCR1_P1_STOP BIT(31)
+
+static u32 boot_gcr1;
+static void __iomem *fsl_mc_regs;
+
/**
* fsl_mc_bus_probe - callback invoked when the root MC bus is being
* added
@@ -947,6 +954,21 @@ static int fsl_mc_bus_probe(struct platform_device *pdev)
struct mc_version mc_version;
struct resource *plat_res;
+ /*
+ * The MC firmware requires full access to the whole address space plus
+ * it has no way of dealing with any kind of address translation, so
+ * request direct mapping for it.
+ */
+ error = iommu_request_dm_for_dev(&pdev->dev);
+ if (error)
+ dev_warn(&pdev->dev, "iommu_request_dm_for_dev() failed: %d\n",
+ error);
+
+ if (fsl_mc_regs) {
+ /* Resume the firmware */
+ writel(boot_gcr1 & ~GCR1_P1_STOP, fsl_mc_regs + FSL_MC_GCR1);
+ }
+
mc = devm_kzalloc(&pdev->dev, sizeof(*mc), GFP_KERNEL);
if (!mc)
return -ENOMEM;
@@ -1027,6 +1049,13 @@ static int fsl_mc_bus_remove(struct platform_device *pdev)
if (!fsl_mc_is_root_dprc(&mc->root_mc_bus_dev->dev))
return -EINVAL;
+ /*
+ * Pause back the firmware so that it doesn't trigger faults by the
+ * time SMMU gets brought down.
+ */
+ writel(boot_gcr1 | GCR1_P1_STOP, fsl_mc_regs + FSL_MC_GCR1);
+ iounmap(fsl_mc_regs);
+
fsl_mc_device_remove(mc->root_mc_bus_dev);
fsl_destroy_mc_io(mc->root_mc_bus_dev->mc_io);
@@ -1062,6 +1091,8 @@ static struct platform_driver fsl_mc_bus_driver = {
static int __init fsl_mc_bus_driver_init(void)
{
int error;
+ struct device_node *np;
+ struct resource res;
error = bus_register(&fsl_mc_bus_type);
if (error < 0) {
@@ -1083,9 +1114,30 @@ static int __init fsl_mc_bus_driver_init(void)
if (error < 0)
goto error_cleanup_dprc_driver;
+ np = of_find_matching_node(NULL, fsl_mc_bus_match_table);
+ if (np && of_device_is_available(np)) {
+ error = of_address_to_resource(np, 1, &res);
+ if (error)
+ goto error_cleanup_dprc_driver;
+ fsl_mc_regs = ioremap(res.start, resource_size(&res));
+ if (!fsl_mc_regs) {
+ error = -ENXIO;
+ goto error_cleanup_dprc_driver;
+ }
+
+ boot_gcr1 = readl(fsl_mc_regs + FSL_MC_GCR1);
+ /*
+ * If found running, pause MC firmware in order to get a chance
+ * to setup SMMU for it.
+ */
+ if (!(boot_gcr1 & GCR1_P1_STOP))
+ writel(boot_gcr1 | GCR1_P1_STOP, fsl_mc_regs + FSL_MC_GCR1);
+ }
+
return 0;
error_cleanup_dprc_driver:
+ iounmap(fsl_mc_regs);
dprc_driver_exit();
error_cleanup_driver:
--
2.17.1
[-- Attachment #7: 0006-arm64-dts-lx2160a-add-iommus-property-for-mc-node.patch --]
[-- Type: text/x-patch, Size: 1023 bytes --]
From 20d7ad3cb903d834dbb281f77ffa9074ab7fe65b Mon Sep 17 00:00:00 2001
From: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Date: Tue, 19 Nov 2019 17:01:39 +0200
Subject: [PATCH 6/6] arm64: dts: lx2160a: add iommus property for mc node
Content-Type: text/plain; charset="us-ascii"
Enable SMMU management for the MC firmware by adding the required
iommus property in the device tree node.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
---
arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi b/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
index aee2810d91cc..e9bf3f6e670a 100644
--- a/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
@@ -967,6 +967,7 @@
msi-parent = <&its>;
/* iommu-map property is fixed up by u-boot */
iommu-map = <0 &smmu 0 0>;
+ iommus = <&smmu 0x4000>;
dma-coherent;
#address-cells = <3>;
#size-cells = <1>;
--
2.17.1
[-- Attachment #8: Type: text/plain, Size: 156 bytes --]
_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu
^ permalink raw reply related [flat|nested] 24+ messages in thread
* Re: [PATCH] iommu: silence iommu group prints
2020-03-04 8:56 ` Laurentiu Tudor
@ 2020-03-04 9:33 ` Russell King - ARM Linux admin
2020-03-04 9:42 ` Laurentiu Tudor
0 siblings, 1 reply; 24+ messages in thread
From: Russell King - ARM Linux admin @ 2020-03-04 9:33 UTC (permalink / raw)
To: Laurentiu Tudor
Cc: Diana Madalina Craciun, iommu, Robin Murphy, Ioana Ciornei
On Wed, Mar 04, 2020 at 10:56:06AM +0200, Laurentiu Tudor wrote:
>
> On 04.03.2020 00:17, Russell King - ARM Linux admin wrote:
> > On Tue, Mar 03, 2020 at 05:55:05PM +0200, Laurentiu Tudor wrote:
> > > From c98dc05cdd45ae923654f2427985bd28bcde4bb2 Mon Sep 17 00:00:00 2001
> > > From: Laurentiu Tudor <laurentiu.tudor@nxp.com>
> > > Date: Thu, 13 Feb 2020 11:59:12 +0200
> > > Subject: [PATCH 1/4] bus: fsl-mc: add custom .dma_configure implementation
> > > Content-Type: text/plain; charset="us-ascii"
> > >
> > > The devices on this bus are not discovered by way of device tree
> > > but by queries to the firmware. It makes little sense to trick the
> > > generic of layer into thinking that these devices are of related so
> > > that we can get our dma configuration. Instead of doing that, add
> > > our custom dma configuration implementation.
> >
> > Firstly, applying this to v5.5 results in a build failure, due to a
> > missing linux/iommu.h include.
> >
> > Secondly, this on its own appears to make the DPAA2 network interfaces
> > completely disappear. Looking in /sys/bus/fsl-mc/drivers/*, none of
> > the DPAA2 drivers are bound to anything, and looking in
> > /sys/bus/fsl-mc/devices/, there is:
> >
> > lrwxrwxrwx 1 root root 0 Mar 3 22:06 dprc.1 -> ../../../devices/platform/soc/80c000000.fsl-mc/dprc.1
> >
> > This is booting with u-boot, so using DT rather than ACPI.
> >
> > > Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
> > > ---
> > > drivers/bus/fsl-mc/fsl-mc-bus.c | 42 ++++++++++++++++++++++++++++++++-
> > > 1 file changed, 41 insertions(+), 1 deletion(-)
> > >
> > > diff --git a/drivers/bus/fsl-mc/fsl-mc-bus.c b/drivers/bus/fsl-mc/fsl-mc-bus.c
> > > index 36eb25f82c8e..3df015eedae4 100644
> > > --- a/drivers/bus/fsl-mc/fsl-mc-bus.c
> > > +++ b/drivers/bus/fsl-mc/fsl-mc-bus.c
> > > @@ -132,11 +132,51 @@ static int fsl_mc_bus_uevent(struct device *dev, struct kobj_uevent_env *env)
> > > static int fsl_mc_dma_configure(struct device *dev)
> > > {
> > > struct device *dma_dev = dev;
> > > + struct iommu_fwspec *fwspec;
> > > + const struct iommu_ops *iommu_ops;
> > > + struct fsl_mc_device *mc_dev = to_fsl_mc_device(dev);
> > > + int ret;
> > > + u32 icid;
> > > +
> > > + /* Skip DMA setup for devices that are not DMA masters */
> > > + if (dev->type == &fsl_mc_bus_dpmcp_type ||
> > > + dev->type == &fsl_mc_bus_dpbp_type ||
> > > + dev->type == &fsl_mc_bus_dpcon_type ||
> > > + dev->type == &fsl_mc_bus_dpio_type)
> > > + return 0;
> > > while (dev_is_fsl_mc(dma_dev))
> > > dma_dev = dma_dev->parent;
> > > - return of_dma_configure(dev, dma_dev->of_node, 0);
> > > + fwspec = dev_iommu_fwspec_get(dma_dev);
> > > + if (!fwspec)
> > > + return -ENODEV;
> >
> > The problem appears to be here - fwspec is NULL for dprc.1.
>
> Ok, that's because the iommu config is missing from the DT node that's
> exposing the MC firmware. I've attached a fresh set of patches that include
> on top the missing config and a workaround that makes MC work over SMMU.
> Also added the missing #include, thanks for pointing out.
> Let me know how it goes.
Shouldn't patch 6 should be first in the series, so that patch 1 does
not cause a regression and bisectability damage?
--
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up
According to speedtest.net: 11.9Mbps down 500kbps up
_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH] iommu: silence iommu group prints
2020-03-04 9:33 ` Russell King - ARM Linux admin
@ 2020-03-04 9:42 ` Laurentiu Tudor
2020-03-04 9:51 ` Russell King - ARM Linux admin
0 siblings, 1 reply; 24+ messages in thread
From: Laurentiu Tudor @ 2020-03-04 9:42 UTC (permalink / raw)
To: Russell King - ARM Linux admin
Cc: Diana Madalina Craciun, iommu, Robin Murphy, Ioana Ciornei
On 04.03.2020 11:33, Russell King - ARM Linux admin wrote:
> On Wed, Mar 04, 2020 at 10:56:06AM +0200, Laurentiu Tudor wrote:
>>
>> On 04.03.2020 00:17, Russell King - ARM Linux admin wrote:
>>> On Tue, Mar 03, 2020 at 05:55:05PM +0200, Laurentiu Tudor wrote:
>>>> From c98dc05cdd45ae923654f2427985bd28bcde4bb2 Mon Sep 17 00:00:00 2001
>>>> From: Laurentiu Tudor <laurentiu.tudor@nxp.com>
>>>> Date: Thu, 13 Feb 2020 11:59:12 +0200
>>>> Subject: [PATCH 1/4] bus: fsl-mc: add custom .dma_configure implementation
>>>> Content-Type: text/plain; charset="us-ascii"
>>>>
>>>> The devices on this bus are not discovered by way of device tree
>>>> but by queries to the firmware. It makes little sense to trick the
>>>> generic of layer into thinking that these devices are of related so
>>>> that we can get our dma configuration. Instead of doing that, add
>>>> our custom dma configuration implementation.
>>>
>>> Firstly, applying this to v5.5 results in a build failure, due to a
>>> missing linux/iommu.h include.
>>>
>>> Secondly, this on its own appears to make the DPAA2 network interfaces
>>> completely disappear. Looking in /sys/bus/fsl-mc/drivers/*, none of
>>> the DPAA2 drivers are bound to anything, and looking in
>>> /sys/bus/fsl-mc/devices/, there is:
>>>
>>> lrwxrwxrwx 1 root root 0 Mar 3 22:06 dprc.1 -> ../../../devices/platform/soc/80c000000.fsl-mc/dprc.1
>>>
>>> This is booting with u-boot, so using DT rather than ACPI.
>>>
>>>> Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
>>>> ---
>>>> drivers/bus/fsl-mc/fsl-mc-bus.c | 42 ++++++++++++++++++++++++++++++++-
>>>> 1 file changed, 41 insertions(+), 1 deletion(-)
>>>>
>>>> diff --git a/drivers/bus/fsl-mc/fsl-mc-bus.c b/drivers/bus/fsl-mc/fsl-mc-bus.c
>>>> index 36eb25f82c8e..3df015eedae4 100644
>>>> --- a/drivers/bus/fsl-mc/fsl-mc-bus.c
>>>> +++ b/drivers/bus/fsl-mc/fsl-mc-bus.c
>>>> @@ -132,11 +132,51 @@ static int fsl_mc_bus_uevent(struct device *dev, struct kobj_uevent_env *env)
>>>> static int fsl_mc_dma_configure(struct device *dev)
>>>> {
>>>> struct device *dma_dev = dev;
>>>> + struct iommu_fwspec *fwspec;
>>>> + const struct iommu_ops *iommu_ops;
>>>> + struct fsl_mc_device *mc_dev = to_fsl_mc_device(dev);
>>>> + int ret;
>>>> + u32 icid;
>>>> +
>>>> + /* Skip DMA setup for devices that are not DMA masters */
>>>> + if (dev->type == &fsl_mc_bus_dpmcp_type ||
>>>> + dev->type == &fsl_mc_bus_dpbp_type ||
>>>> + dev->type == &fsl_mc_bus_dpcon_type ||
>>>> + dev->type == &fsl_mc_bus_dpio_type)
>>>> + return 0;
>>>> while (dev_is_fsl_mc(dma_dev))
>>>> dma_dev = dma_dev->parent;
>>>> - return of_dma_configure(dev, dma_dev->of_node, 0);
>>>> + fwspec = dev_iommu_fwspec_get(dma_dev);
>>>> + if (!fwspec)
>>>> + return -ENODEV;
>>>
>>> The problem appears to be here - fwspec is NULL for dprc.1.
>>
>> Ok, that's because the iommu config is missing from the DT node that's
>> exposing the MC firmware. I've attached a fresh set of patches that include
>> on top the missing config and a workaround that makes MC work over SMMU.
>> Also added the missing #include, thanks for pointing out.
>> Let me know how it goes.
>
> Shouldn't patch 6 should be first in the series, so that patch 1 does
> not cause a regression and bisectability damage?
>
Correct, width one comment: both 5 and 6 should go first. Once iommu-map
is added in the device tree the workaround for MC with the
arm-smmu.disable_bypass boot arg will no longer work.
---
Best Regards, Laurentiu
_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH] iommu: silence iommu group prints
2020-03-04 9:42 ` Laurentiu Tudor
@ 2020-03-04 9:51 ` Russell King - ARM Linux admin
2020-03-04 9:56 ` Laurentiu Tudor
0 siblings, 1 reply; 24+ messages in thread
From: Russell King - ARM Linux admin @ 2020-03-04 9:51 UTC (permalink / raw)
To: Laurentiu Tudor
Cc: Diana Madalina Craciun, iommu, Robin Murphy, Ioana Ciornei
On Wed, Mar 04, 2020 at 11:42:16AM +0200, Laurentiu Tudor wrote:
> On 04.03.2020 11:33, Russell King - ARM Linux admin wrote:
> > On Wed, Mar 04, 2020 at 10:56:06AM +0200, Laurentiu Tudor wrote:
> > >
> > > On 04.03.2020 00:17, Russell King - ARM Linux admin wrote:
> > > > On Tue, Mar 03, 2020 at 05:55:05PM +0200, Laurentiu Tudor wrote:
> > > > > From c98dc05cdd45ae923654f2427985bd28bcde4bb2 Mon Sep 17 00:00:00 2001
> > > > > From: Laurentiu Tudor <laurentiu.tudor@nxp.com>
> > > > > Date: Thu, 13 Feb 2020 11:59:12 +0200
> > > > > Subject: [PATCH 1/4] bus: fsl-mc: add custom .dma_configure implementation
> > > > > Content-Type: text/plain; charset="us-ascii"
> > > > >
> > > > > The devices on this bus are not discovered by way of device tree
> > > > > but by queries to the firmware. It makes little sense to trick the
> > > > > generic of layer into thinking that these devices are of related so
> > > > > that we can get our dma configuration. Instead of doing that, add
> > > > > our custom dma configuration implementation.
> > > >
> > > > Firstly, applying this to v5.5 results in a build failure, due to a
> > > > missing linux/iommu.h include.
> > > >
> > > > Secondly, this on its own appears to make the DPAA2 network interfaces
> > > > completely disappear. Looking in /sys/bus/fsl-mc/drivers/*, none of
> > > > the DPAA2 drivers are bound to anything, and looking in
> > > > /sys/bus/fsl-mc/devices/, there is:
> > > >
> > > > lrwxrwxrwx 1 root root 0 Mar 3 22:06 dprc.1 -> ../../../devices/platform/soc/80c000000.fsl-mc/dprc.1
> > > >
> > > > This is booting with u-boot, so using DT rather than ACPI.
> > > >
> > > > > Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
> > > > > ---
> > > > > drivers/bus/fsl-mc/fsl-mc-bus.c | 42 ++++++++++++++++++++++++++++++++-
> > > > > 1 file changed, 41 insertions(+), 1 deletion(-)
> > > > >
> > > > > diff --git a/drivers/bus/fsl-mc/fsl-mc-bus.c b/drivers/bus/fsl-mc/fsl-mc-bus.c
> > > > > index 36eb25f82c8e..3df015eedae4 100644
> > > > > --- a/drivers/bus/fsl-mc/fsl-mc-bus.c
> > > > > +++ b/drivers/bus/fsl-mc/fsl-mc-bus.c
> > > > > @@ -132,11 +132,51 @@ static int fsl_mc_bus_uevent(struct device *dev, struct kobj_uevent_env *env)
> > > > > static int fsl_mc_dma_configure(struct device *dev)
> > > > > {
> > > > > struct device *dma_dev = dev;
> > > > > + struct iommu_fwspec *fwspec;
> > > > > + const struct iommu_ops *iommu_ops;
> > > > > + struct fsl_mc_device *mc_dev = to_fsl_mc_device(dev);
> > > > > + int ret;
> > > > > + u32 icid;
> > > > > +
> > > > > + /* Skip DMA setup for devices that are not DMA masters */
> > > > > + if (dev->type == &fsl_mc_bus_dpmcp_type ||
> > > > > + dev->type == &fsl_mc_bus_dpbp_type ||
> > > > > + dev->type == &fsl_mc_bus_dpcon_type ||
> > > > > + dev->type == &fsl_mc_bus_dpio_type)
> > > > > + return 0;
> > > > > while (dev_is_fsl_mc(dma_dev))
> > > > > dma_dev = dma_dev->parent;
> > > > > - return of_dma_configure(dev, dma_dev->of_node, 0);
> > > > > + fwspec = dev_iommu_fwspec_get(dma_dev);
> > > > > + if (!fwspec)
> > > > > + return -ENODEV;
> > > >
> > > > The problem appears to be here - fwspec is NULL for dprc.1.
> > >
> > > Ok, that's because the iommu config is missing from the DT node that's
> > > exposing the MC firmware. I've attached a fresh set of patches that include
> > > on top the missing config and a workaround that makes MC work over SMMU.
> > > Also added the missing #include, thanks for pointing out.
> > > Let me know how it goes.
> >
> > Shouldn't patch 6 should be first in the series, so that patch 1 does
> > not cause a regression and bisectability damage?
> >
>
> Correct, width one comment: both 5 and 6 should go first. Once iommu-map is
> added in the device tree the workaround for MC with the
> arm-smmu.disable_bypass boot arg will no longer work.
So, wouldn't it be reasonable to arrange the patch series like that?
--
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up
According to speedtest.net: 11.9Mbps down 500kbps up
_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH] iommu: silence iommu group prints
2020-03-04 9:51 ` Russell King - ARM Linux admin
@ 2020-03-04 9:56 ` Laurentiu Tudor
2020-03-04 10:07 ` Russell King - ARM Linux admin
0 siblings, 1 reply; 24+ messages in thread
From: Laurentiu Tudor @ 2020-03-04 9:56 UTC (permalink / raw)
To: Russell King - ARM Linux admin
Cc: Diana Madalina Craciun, iommu, Robin Murphy, Ioana Ciornei
[-- Attachment #1: Type: text/plain, Size: 3902 bytes --]
On 04.03.2020 11:51, Russell King - ARM Linux admin wrote:
> On Wed, Mar 04, 2020 at 11:42:16AM +0200, Laurentiu Tudor wrote:
>> On 04.03.2020 11:33, Russell King - ARM Linux admin wrote:
>>> On Wed, Mar 04, 2020 at 10:56:06AM +0200, Laurentiu Tudor wrote:
>>>>
>>>> On 04.03.2020 00:17, Russell King - ARM Linux admin wrote:
>>>>> On Tue, Mar 03, 2020 at 05:55:05PM +0200, Laurentiu Tudor wrote:
>>>>>> From c98dc05cdd45ae923654f2427985bd28bcde4bb2 Mon Sep 17 00:00:00 2001
>>>>>> From: Laurentiu Tudor <laurentiu.tudor@nxp.com>
>>>>>> Date: Thu, 13 Feb 2020 11:59:12 +0200
>>>>>> Subject: [PATCH 1/4] bus: fsl-mc: add custom .dma_configure implementation
>>>>>> Content-Type: text/plain; charset="us-ascii"
>>>>>>
>>>>>> The devices on this bus are not discovered by way of device tree
>>>>>> but by queries to the firmware. It makes little sense to trick the
>>>>>> generic of layer into thinking that these devices are of related so
>>>>>> that we can get our dma configuration. Instead of doing that, add
>>>>>> our custom dma configuration implementation.
>>>>>
>>>>> Firstly, applying this to v5.5 results in a build failure, due to a
>>>>> missing linux/iommu.h include.
>>>>>
>>>>> Secondly, this on its own appears to make the DPAA2 network interfaces
>>>>> completely disappear. Looking in /sys/bus/fsl-mc/drivers/*, none of
>>>>> the DPAA2 drivers are bound to anything, and looking in
>>>>> /sys/bus/fsl-mc/devices/, there is:
>>>>>
>>>>> lrwxrwxrwx 1 root root 0 Mar 3 22:06 dprc.1 -> ../../../devices/platform/soc/80c000000.fsl-mc/dprc.1
>>>>>
>>>>> This is booting with u-boot, so using DT rather than ACPI.
>>>>>
>>>>>> Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
>>>>>> ---
>>>>>> drivers/bus/fsl-mc/fsl-mc-bus.c | 42 ++++++++++++++++++++++++++++++++-
>>>>>> 1 file changed, 41 insertions(+), 1 deletion(-)
>>>>>>
>>>>>> diff --git a/drivers/bus/fsl-mc/fsl-mc-bus.c b/drivers/bus/fsl-mc/fsl-mc-bus.c
>>>>>> index 36eb25f82c8e..3df015eedae4 100644
>>>>>> --- a/drivers/bus/fsl-mc/fsl-mc-bus.c
>>>>>> +++ b/drivers/bus/fsl-mc/fsl-mc-bus.c
>>>>>> @@ -132,11 +132,51 @@ static int fsl_mc_bus_uevent(struct device *dev, struct kobj_uevent_env *env)
>>>>>> static int fsl_mc_dma_configure(struct device *dev)
>>>>>> {
>>>>>> struct device *dma_dev = dev;
>>>>>> + struct iommu_fwspec *fwspec;
>>>>>> + const struct iommu_ops *iommu_ops;
>>>>>> + struct fsl_mc_device *mc_dev = to_fsl_mc_device(dev);
>>>>>> + int ret;
>>>>>> + u32 icid;
>>>>>> +
>>>>>> + /* Skip DMA setup for devices that are not DMA masters */
>>>>>> + if (dev->type == &fsl_mc_bus_dpmcp_type ||
>>>>>> + dev->type == &fsl_mc_bus_dpbp_type ||
>>>>>> + dev->type == &fsl_mc_bus_dpcon_type ||
>>>>>> + dev->type == &fsl_mc_bus_dpio_type)
>>>>>> + return 0;
>>>>>> while (dev_is_fsl_mc(dma_dev))
>>>>>> dma_dev = dma_dev->parent;
>>>>>> - return of_dma_configure(dev, dma_dev->of_node, 0);
>>>>>> + fwspec = dev_iommu_fwspec_get(dma_dev);
>>>>>> + if (!fwspec)
>>>>>> + return -ENODEV;
>>>>>
>>>>> The problem appears to be here - fwspec is NULL for dprc.1.
>>>>
>>>> Ok, that's because the iommu config is missing from the DT node that's
>>>> exposing the MC firmware. I've attached a fresh set of patches that include
>>>> on top the missing config and a workaround that makes MC work over SMMU.
>>>> Also added the missing #include, thanks for pointing out.
>>>> Let me know how it goes.
>>>
>>> Shouldn't patch 6 should be first in the series, so that patch 1 does
>>> not cause a regression and bisectability damage?
>>>
>>
>> Correct, width one comment: both 5 and 6 should go first. Once iommu-map is
>> added in the device tree the workaround for MC with the
>> arm-smmu.disable_bypass boot arg will no longer work.
>
> So, wouldn't it be reasonable to arrange the patch series like that?
>
Sure, please see attached.
---
Best Regards, Laurentiu
[-- Attachment #2: 0001-bus-fsl-mc-make-mc-work-with-smmu-disable-bypass-on.patch --]
[-- Type: text/x-patch, Size: 4164 bytes --]
From 44ae46501b5379bd0890df87fd3827248626ed03 Mon Sep 17 00:00:00 2001
From: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Date: Tue, 1 Oct 2019 16:22:48 +0300
Subject: [PATCH 1/6] bus: fsl-mc: make mc work with smmu disable bypass on
Content-Type: text/plain; charset="us-ascii"
Since this commit [1] booting kernel on MC based chips started to
fail because this firmware starts before the kernel and as soon as
SMMU is probed it starts to trigger contiguous faults.
This is a workaround that allows MC firmware to run with SMMU
in disable bypass mode. It consists of the following steps:
1. pause the firmware at early boot to get a chance to setup SMMU
2. request direct mapping for MC device
3. resume the firmware
The workaround relies on the fact that no state is lost when
pausing / resuming firmware, as per the docs.
With this patch, platforms with MC firmware can now boot without
having to change the default config to set:
CONFIG_ARM_SMMU_DISABLE_BYPASS_BY_DEFAULT=n
[1] 954a03be033 ("iommu/arm-smmu: Break insecure users by disabling bypass by default")
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
---
drivers/bus/fsl-mc/fsl-mc-bus.c | 53 +++++++++++++++++++++++++++++++++
1 file changed, 53 insertions(+)
diff --git a/drivers/bus/fsl-mc/fsl-mc-bus.c b/drivers/bus/fsl-mc/fsl-mc-bus.c
index a0f8854acb3a..683a6401ffe8 100644
--- a/drivers/bus/fsl-mc/fsl-mc-bus.c
+++ b/drivers/bus/fsl-mc/fsl-mc-bus.c
@@ -18,6 +18,8 @@
#include <linux/bitops.h>
#include <linux/msi.h>
#include <linux/dma-mapping.h>
+#include <linux/iommu.h>
+#include <linux/io.h>
#include "fsl-mc-private.h"
@@ -889,6 +891,12 @@ static int get_mc_addr_translation_ranges(struct device *dev,
return 0;
}
+#define FSL_MC_GCR1 0x0
+#define GCR1_P1_STOP BIT(31)
+
+static u32 boot_gcr1;
+static void __iomem *fsl_mc_regs;
+
/**
* fsl_mc_bus_probe - callback invoked when the root MC bus is being
* added
@@ -906,6 +914,21 @@ static int fsl_mc_bus_probe(struct platform_device *pdev)
struct mc_version mc_version;
struct resource res;
+ /*
+ * The MC firmware requires full access to the whole address space plus
+ * it has no way of dealing with any kind of address translation, so
+ * request direct mapping for it.
+ */
+ error = iommu_request_dm_for_dev(&pdev->dev);
+ if (error)
+ dev_warn(&pdev->dev, "iommu_request_dm_for_dev() failed: %d\n",
+ error);
+
+ if (fsl_mc_regs) {
+ /* Resume the firmware */
+ writel(boot_gcr1 & ~GCR1_P1_STOP, fsl_mc_regs + FSL_MC_GCR1);
+ }
+
mc = devm_kzalloc(&pdev->dev, sizeof(*mc), GFP_KERNEL);
if (!mc)
return -ENOMEM;
@@ -990,6 +1013,13 @@ static int fsl_mc_bus_remove(struct platform_device *pdev)
if (!fsl_mc_is_root_dprc(&mc->root_mc_bus_dev->dev))
return -EINVAL;
+ /*
+ * Pause back the firmware so that it doesn't trigger faults by the
+ * time SMMU gets brought down.
+ */
+ writel(boot_gcr1 | GCR1_P1_STOP, fsl_mc_regs + FSL_MC_GCR1);
+ iounmap(fsl_mc_regs);
+
fsl_mc_device_remove(mc->root_mc_bus_dev);
fsl_destroy_mc_io(mc->root_mc_bus_dev->mc_io);
@@ -1018,6 +1048,8 @@ static struct platform_driver fsl_mc_bus_driver = {
static int __init fsl_mc_bus_driver_init(void)
{
int error;
+ struct device_node *np;
+ struct resource res;
error = bus_register(&fsl_mc_bus_type);
if (error < 0) {
@@ -1039,9 +1071,30 @@ static int __init fsl_mc_bus_driver_init(void)
if (error < 0)
goto error_cleanup_dprc_driver;
+ np = of_find_matching_node(NULL, fsl_mc_bus_match_table);
+ if (np && of_device_is_available(np)) {
+ error = of_address_to_resource(np, 1, &res);
+ if (error)
+ goto error_cleanup_dprc_driver;
+ fsl_mc_regs = ioremap(res.start, resource_size(&res));
+ if (!fsl_mc_regs) {
+ error = -ENXIO;
+ goto error_cleanup_dprc_driver;
+ }
+
+ boot_gcr1 = readl(fsl_mc_regs + FSL_MC_GCR1);
+ /*
+ * If found running, pause MC firmware in order to get a chance
+ * to setup SMMU for it.
+ */
+ if (!(boot_gcr1 & GCR1_P1_STOP))
+ writel(boot_gcr1 | GCR1_P1_STOP, fsl_mc_regs + FSL_MC_GCR1);
+ }
+
return 0;
error_cleanup_dprc_driver:
+ iounmap(fsl_mc_regs);
dprc_driver_exit();
error_cleanup_driver:
--
2.17.1
[-- Attachment #3: 0002-arm64-dts-lx2160a-add-iommus-property-for-mc-node.patch --]
[-- Type: text/x-patch, Size: 1023 bytes --]
From 5d497723fb1695d1e880cfdb7b2f32fbd0e9ecc7 Mon Sep 17 00:00:00 2001
From: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Date: Tue, 19 Nov 2019 17:01:39 +0200
Subject: [PATCH 2/6] arm64: dts: lx2160a: add iommus property for mc node
Content-Type: text/plain; charset="us-ascii"
Enable SMMU management for the MC firmware by adding the required
iommus property in the device tree node.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
---
arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi b/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
index aee2810d91cc..e9bf3f6e670a 100644
--- a/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
@@ -967,6 +967,7 @@
msi-parent = <&its>;
/* iommu-map property is fixed up by u-boot */
iommu-map = <0 &smmu 0 0>;
+ iommus = <&smmu 0x4000>;
dma-coherent;
#address-cells = <3>;
#size-cells = <1>;
--
2.17.1
[-- Attachment #4: 0003-bus-fsl-mc-add-custom-.dma_configure-implementation.patch --]
[-- Type: text/x-patch, Size: 2391 bytes --]
From b226e187452cb2b75bd8a3ebb239c6320022c89b Mon Sep 17 00:00:00 2001
From: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Date: Thu, 13 Feb 2020 11:59:12 +0200
Subject: [PATCH 3/6] bus: fsl-mc: add custom .dma_configure implementation
Content-Type: text/plain; charset="us-ascii"
The devices on this bus are not discovered by way of device tree
but by queries to the firmware. It makes little sense to trick the
generic of layer into thinking that these devices are of related so
that we can get our dma configuration. Instead of doing that, add
our custom dma configuration implementation.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
---
drivers/bus/fsl-mc/fsl-mc-bus.c | 42 ++++++++++++++++++++++++++++++++-
1 file changed, 41 insertions(+), 1 deletion(-)
diff --git a/drivers/bus/fsl-mc/fsl-mc-bus.c b/drivers/bus/fsl-mc/fsl-mc-bus.c
index 683a6401ffe8..665893058004 100644
--- a/drivers/bus/fsl-mc/fsl-mc-bus.c
+++ b/drivers/bus/fsl-mc/fsl-mc-bus.c
@@ -132,11 +132,51 @@ static int fsl_mc_bus_uevent(struct device *dev, struct kobj_uevent_env *env)
static int fsl_mc_dma_configure(struct device *dev)
{
struct device *dma_dev = dev;
+ struct iommu_fwspec *fwspec;
+ const struct iommu_ops *iommu_ops;
+ struct fsl_mc_device *mc_dev = to_fsl_mc_device(dev);
+ int ret;
+ u32 icid;
+
+ /* Skip DMA setup for devices that are not DMA masters */
+ if (dev->type == &fsl_mc_bus_dpmcp_type ||
+ dev->type == &fsl_mc_bus_dpbp_type ||
+ dev->type == &fsl_mc_bus_dpcon_type ||
+ dev->type == &fsl_mc_bus_dpio_type)
+ return 0;
while (dev_is_fsl_mc(dma_dev))
dma_dev = dma_dev->parent;
- return of_dma_configure(dev, dma_dev->of_node, 0);
+ fwspec = dev_iommu_fwspec_get(dma_dev);
+ if (!fwspec)
+ return -ENODEV;
+ iommu_ops = iommu_ops_from_fwnode(fwspec->iommu_fwnode);
+ if (!iommu_ops)
+ return -ENODEV;
+
+ ret = iommu_fwspec_init(dev, fwspec->iommu_fwnode, iommu_ops);
+ if (ret)
+ return ret;
+
+ icid = mc_dev->icid;
+ ret = iommu_fwspec_add_ids(dev, &icid, 1);
+ if (ret) {
+ iommu_fwspec_free(dev);
+ return ret;
+ }
+
+ if (!device_iommu_mapped(dev)) {
+ ret = iommu_probe_device(dev);
+ if (ret) {
+ iommu_fwspec_free(dev);
+ return ret;
+ }
+ }
+
+ arch_setup_dma_ops(dev, 0, *dma_dev->dma_mask + 1, iommu_ops, true);
+
+ return 0;
}
static ssize_t modalias_show(struct device *dev, struct device_attribute *attr,
--
2.17.1
[-- Attachment #5: 0004-irqchip-fsl-mc-Change-the-way-the-IRQ-domain-is-set-.patch --]
[-- Type: text/x-patch, Size: 1818 bytes --]
From 8b6bf2096ff2ec99f477a8bd43c590d4876ea21e Mon Sep 17 00:00:00 2001
From: Diana Craciun <diana.craciun@oss.nxp.com>
Date: Fri, 14 Feb 2020 16:28:45 +0200
Subject: [PATCH 4/6] irqchip/fsl-mc: Change the way the IRQ domain is set for
MC devices
Content-Type: text/plain; charset="us-ascii"
In ACPI the MC bus is represented as a platform device and a named
component in the IORT table. The mc-bus devices are discovered
dynamically at runtime but they share the same fwnode with the parent
platfom device. This patch changes the way the IRQ domain is searched
for the MC devices: it takes the fwnode reference from the parent and
uses the fwnode reference to find the MC IRQ domain.
Signed-off-by: Diana Craciun <diana.craciun@oss.nxp.com>
---
drivers/bus/fsl-mc/fsl-mc-msi.c | 11 +++++++++--
1 file changed, 9 insertions(+), 2 deletions(-)
diff --git a/drivers/bus/fsl-mc/fsl-mc-msi.c b/drivers/bus/fsl-mc/fsl-mc-msi.c
index 8b9c66d7c4ff..1e2e97329781 100644
--- a/drivers/bus/fsl-mc/fsl-mc-msi.c
+++ b/drivers/bus/fsl-mc/fsl-mc-msi.c
@@ -182,16 +182,23 @@ int fsl_mc_find_msi_domain(struct device *mc_platform_dev,
{
struct irq_domain *msi_domain;
struct device_node *mc_of_node = mc_platform_dev->of_node;
+ struct fwnode_handle *fwnode;
- msi_domain = of_msi_get_domain(mc_platform_dev, mc_of_node,
- DOMAIN_BUS_FSL_MC_MSI);
+ msi_domain = dev_get_msi_domain(mc_platform_dev);
if (!msi_domain) {
pr_err("Unable to find fsl-mc MSI domain for %pOF\n",
mc_of_node);
return -ENOENT;
}
+ fwnode = msi_domain->fwnode;
+ msi_domain = irq_find_matching_fwnode(fwnode, DOMAIN_BUS_FSL_MC_MSI);
+ if (!msi_domain) {
+ pr_err("Unable to find fsl-mc MSI domain for %pOF\n",
+ mc_of_node);
+ return -ENOENT;
+ }
*mc_msi_domain = msi_domain;
return 0;
}
--
2.17.1
[-- Attachment #6: 0005-bus-fsl-mc-Add-ACPI-support-for-fsl-mc.patch --]
[-- Type: text/x-patch, Size: 6022 bytes --]
From d52fffe8be38ccaa040e56b9ca2b58db1a0fe742 Mon Sep 17 00:00:00 2001
From: Makarand Pawagi <makarand.pawagi@nxp.com>
Date: Thu, 23 Jan 2020 10:48:42 +0530
Subject: [PATCH 5/6] bus: fsl-mc: Add ACPI support for fsl-mc
Content-Type: text/plain; charset="us-ascii"
ACPI support is added in the fsl-mc driver. Driver will parse
MC DSDT table to extract memory and other resorces.
Interrupt (GIC ITS) information will be extracted from MADT table
by drivers/irqchip/irq-gic-v3-its-fsl-mc-msi.c.
IORT table will be parsed to configure DMA.
Signed-off-by: Makarand Pawagi <makarand.pawagi@nxp.com>
---
drivers/bus/fsl-mc/fsl-mc-bus.c | 35 ++++++-----
drivers/irqchip/irq-gic-v3-its-fsl-mc-msi.c | 69 ++++++++++++++++++++-
2 files changed, 87 insertions(+), 17 deletions(-)
diff --git a/drivers/bus/fsl-mc/fsl-mc-bus.c b/drivers/bus/fsl-mc/fsl-mc-bus.c
index 665893058004..8a385df3e25c 100644
--- a/drivers/bus/fsl-mc/fsl-mc-bus.c
+++ b/drivers/bus/fsl-mc/fsl-mc-bus.c
@@ -952,7 +952,7 @@ static int fsl_mc_bus_probe(struct platform_device *pdev)
phys_addr_t mc_portal_phys_addr;
u32 mc_portal_size;
struct mc_version mc_version;
- struct resource res;
+ struct resource *plat_res;
/*
* The MC firmware requires full access to the whole address space plus
@@ -978,16 +978,9 @@ static int fsl_mc_bus_probe(struct platform_device *pdev)
/*
* Get physical address of MC portal for the root DPRC:
*/
- error = of_address_to_resource(pdev->dev.of_node, 0, &res);
- if (error < 0) {
- dev_err(&pdev->dev,
- "of_address_to_resource() failed for %pOF\n",
- pdev->dev.of_node);
- return error;
- }
-
- mc_portal_phys_addr = res.start;
- mc_portal_size = resource_size(&res);
+ plat_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ mc_portal_phys_addr = plat_res->start;
+ mc_portal_size = resource_size(plat_res);
error = fsl_create_mc_io(&pdev->dev, mc_portal_phys_addr,
mc_portal_size, NULL,
FSL_MC_IO_ATOMIC_CONTEXT_PORTAL, &mc_io);
@@ -1004,11 +997,13 @@ static int fsl_mc_bus_probe(struct platform_device *pdev)
dev_info(&pdev->dev, "MC firmware version: %u.%u.%u\n",
mc_version.major, mc_version.minor, mc_version.revision);
- error = get_mc_addr_translation_ranges(&pdev->dev,
- &mc->translation_ranges,
- &mc->num_translation_ranges);
- if (error < 0)
- goto error_cleanup_mc_io;
+ if (dev_of_node(&pdev->dev)) {
+ error = get_mc_addr_translation_ranges(&pdev->dev,
+ &mc->translation_ranges,
+ &mc->num_translation_ranges);
+ if (error < 0)
+ goto error_cleanup_mc_io;
+ }
error = dprc_get_container_id(mc_io, 0, &container_id);
if (error < 0) {
@@ -1035,6 +1030,7 @@ static int fsl_mc_bus_probe(struct platform_device *pdev)
goto error_cleanup_mc_io;
mc->root_mc_bus_dev = mc_bus_dev;
+ mc_bus_dev->dev.fwnode = pdev->dev.fwnode;
return 0;
error_cleanup_mc_io:
@@ -1075,11 +1071,18 @@ static const struct of_device_id fsl_mc_bus_match_table[] = {
MODULE_DEVICE_TABLE(of, fsl_mc_bus_match_table);
+static const struct acpi_device_id fsl_mc_bus_acpi_match_table[] = {
+ {"NXP0008", 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(acpi, fsl_mc_bus_acpi_match_table);
+
static struct platform_driver fsl_mc_bus_driver = {
.driver = {
.name = "fsl_mc_bus",
.pm = NULL,
.of_match_table = fsl_mc_bus_match_table,
+ .acpi_match_table = fsl_mc_bus_acpi_match_table,
},
.probe = fsl_mc_bus_probe,
.remove = fsl_mc_bus_remove,
diff --git a/drivers/irqchip/irq-gic-v3-its-fsl-mc-msi.c b/drivers/irqchip/irq-gic-v3-its-fsl-mc-msi.c
index 606efa64adff..6d67834722c9 100644
--- a/drivers/irqchip/irq-gic-v3-its-fsl-mc-msi.c
+++ b/drivers/irqchip/irq-gic-v3-its-fsl-mc-msi.c
@@ -4,9 +4,11 @@
*
* Copyright (C) 2015-2016 Freescale Semiconductor, Inc.
* Author: German Rivera <German.Rivera@freescale.com>
+ * Copyright 2020 NXP
*
*/
+#include <linux/acpi_iort.h>
#include <linux/of_device.h>
#include <linux/of_address.h>
#include <linux/irq.h>
@@ -66,7 +68,65 @@ static const struct of_device_id its_device_id[] = {
{},
};
-static int __init its_fsl_mc_msi_init(void)
+static int __init its_fsl_mc_msi_init_one(struct fwnode_handle *handle,
+ const char *name)
+{
+ struct irq_domain *parent;
+ struct irq_domain *mc_msi_domain;
+
+ parent = irq_find_matching_fwnode(handle, DOMAIN_BUS_NEXUS);
+ if (!parent || !msi_get_domain_info(parent)) {
+ pr_err("%s: Unable to locate ITS domain\n", name);
+ return -ENXIO;
+ }
+
+ mc_msi_domain = fsl_mc_msi_create_irq_domain(handle,
+ &its_fsl_mc_msi_domain_info,
+ parent);
+ if (!mc_msi_domain)
+ pr_err("ACPIF: unable to create fsl-mc domain\n");
+
+ pr_info("fsl-mc MSI: domain created\n");
+
+ return 0;
+}
+
+static int __init
+its_fsl_mc_msi_parse_madt(union acpi_subtable_headers *header,
+ const unsigned long end)
+{
+ struct acpi_madt_generic_translator *its_entry;
+ struct fwnode_handle *dom_handle;
+ const char *node_name;
+ int err = -ENXIO;
+
+ its_entry = (struct acpi_madt_generic_translator *)header;
+ node_name = kasprintf(GFP_KERNEL, "ITS@0x%lx",
+ (long)its_entry->base_address);
+
+ dom_handle = iort_find_domain_token(its_entry->translation_id);
+ if (!dom_handle) {
+ pr_err("%s: Unable to locate ITS domain handle\n", node_name);
+ goto out;
+ }
+
+ err = its_fsl_mc_msi_init_one(dom_handle, node_name);
+ if (!err)
+ pr_info("fsl-mc MSI: %s domain created\n", node_name);
+
+out:
+ kfree(node_name);
+ return err;
+}
+
+static int __init its_fsl_mc_acpi_msi_init(void)
+{
+ acpi_table_parse_madt(ACPI_MADT_TYPE_GENERIC_TRANSLATOR,
+ its_fsl_mc_msi_parse_madt, 0);
+ return 0;
+}
+
+static int __init its_fsl_mc_of_msi_init(void)
{
struct device_node *np;
struct irq_domain *parent;
@@ -100,4 +160,11 @@ static int __init its_fsl_mc_msi_init(void)
return 0;
}
+static int __init its_fsl_mc_msi_init(void)
+{
+ its_fsl_mc_of_msi_init();
+ its_fsl_mc_acpi_msi_init();
+
+ return 0;
+}
early_initcall(its_fsl_mc_msi_init);
--
2.17.1
[-- Attachment #7: 0006-iommu-of-get-rid-of-fsl-mc-specific-code.patch --]
[-- Type: text/x-patch, Size: 1897 bytes --]
From ff42f0b4375aff9e351817db1e28fa4b3e6211d4 Mon Sep 17 00:00:00 2001
From: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Date: Wed, 26 Feb 2020 17:31:49 +0200
Subject: [PATCH 6/6] iommu/of: get rid of fsl-mc specific code
Content-Type: text/plain; charset="us-ascii"
Changing the way we configure dma for fsl-mc devices allows
us to get rid of our fsl-mc specific code in the generic
of iommu code.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
---
drivers/iommu/of_iommu.c | 20 --------------------
1 file changed, 20 deletions(-)
diff --git a/drivers/iommu/of_iommu.c b/drivers/iommu/of_iommu.c
index 20738aacac89..332072ada474 100644
--- a/drivers/iommu/of_iommu.c
+++ b/drivers/iommu/of_iommu.c
@@ -15,7 +15,6 @@
#include <linux/of_pci.h>
#include <linux/pci.h>
#include <linux/slab.h>
-#include <linux/fsl/mc.h>
#define NO_IOMMU 1
@@ -139,23 +138,6 @@ static int of_pci_iommu_init(struct pci_dev *pdev, u16 alias, void *data)
return err;
}
-static int of_fsl_mc_iommu_init(struct fsl_mc_device *mc_dev,
- struct device_node *master_np)
-{
- struct of_phandle_args iommu_spec = { .args_count = 1 };
- int err;
-
- err = of_map_rid(master_np, mc_dev->icid, "iommu-map",
- "iommu-map-mask", &iommu_spec.np,
- iommu_spec.args);
- if (err)
- return err == -ENODEV ? NO_IOMMU : err;
-
- err = of_iommu_xlate(&mc_dev->dev, &iommu_spec);
- of_node_put(iommu_spec.np);
- return err;
-}
-
const struct iommu_ops *of_iommu_configure(struct device *dev,
struct device_node *master_np)
{
@@ -188,8 +170,6 @@ const struct iommu_ops *of_iommu_configure(struct device *dev,
pci_request_acs();
err = pci_for_each_dma_alias(to_pci_dev(dev),
of_pci_iommu_init, &info);
- } else if (dev_is_fsl_mc(dev)) {
- err = of_fsl_mc_iommu_init(to_fsl_mc_device(dev), master_np);
} else {
struct of_phandle_args iommu_spec;
int idx = 0;
--
2.17.1
[-- Attachment #8: Type: text/plain, Size: 156 bytes --]
_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu
^ permalink raw reply related [flat|nested] 24+ messages in thread
* Re: [PATCH] iommu: silence iommu group prints
2020-03-04 9:56 ` Laurentiu Tudor
@ 2020-03-04 10:07 ` Russell King - ARM Linux admin
2020-03-04 10:33 ` Laurentiu Tudor
0 siblings, 1 reply; 24+ messages in thread
From: Russell King - ARM Linux admin @ 2020-03-04 10:07 UTC (permalink / raw)
To: Laurentiu Tudor, Olof Johansson
Cc: Diana Madalina Craciun, iommu, Robin Murphy, Ioana Ciornei
On Wed, Mar 04, 2020 at 11:56:53AM +0200, Laurentiu Tudor wrote:
> From 44ae46501b5379bd0890df87fd3827248626ed03 Mon Sep 17 00:00:00 2001
> From: Laurentiu Tudor <laurentiu.tudor@nxp.com>
> Date: Tue, 1 Oct 2019 16:22:48 +0300
> Subject: [PATCH 1/6] bus: fsl-mc: make mc work with smmu disable bypass on
> Content-Type: text/plain; charset="us-ascii"
>
> Since this commit [1] booting kernel on MC based chips started to
> fail because this firmware starts before the kernel and as soon as
> SMMU is probed it starts to trigger contiguous faults.
I think you mean "continuous" here.
> This is a workaround that allows MC firmware to run with SMMU
> in disable bypass mode. It consists of the following steps:
> 1. pause the firmware at early boot to get a chance to setup SMMU
> 2. request direct mapping for MC device
> 3. resume the firmware
> The workaround relies on the fact that no state is lost when
> pausing / resuming firmware, as per the docs.
> With this patch, platforms with MC firmware can now boot without
> having to change the default config to set:
> CONFIG_ARM_SMMU_DISABLE_BYPASS_BY_DEFAULT=n
This alone is a definite improvement, and has been needed for a while.
Please submit this patch with an appropriate Fixes: tag so stable trees
can pick it up.
> [1] 954a03be033 ("iommu/arm-smmu: Break insecure users by disabling bypass by default")
Please put this where you're referencing it above - it's fine to wrap
the description of the commit when using it in the body of the commit
message. However, that should _never_ when providing a Fixes: tag
(linux-next has a script which will detect and complain about broken
Fixes: tags.)
Thanks.
>
> Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
> ---
> drivers/bus/fsl-mc/fsl-mc-bus.c | 53 +++++++++++++++++++++++++++++++++
> 1 file changed, 53 insertions(+)
>
> diff --git a/drivers/bus/fsl-mc/fsl-mc-bus.c b/drivers/bus/fsl-mc/fsl-mc-bus.c
> index a0f8854acb3a..683a6401ffe8 100644
> --- a/drivers/bus/fsl-mc/fsl-mc-bus.c
> +++ b/drivers/bus/fsl-mc/fsl-mc-bus.c
> @@ -18,6 +18,8 @@
> #include <linux/bitops.h>
> #include <linux/msi.h>
> #include <linux/dma-mapping.h>
> +#include <linux/iommu.h>
> +#include <linux/io.h>
>
> #include "fsl-mc-private.h"
>
> @@ -889,6 +891,12 @@ static int get_mc_addr_translation_ranges(struct device *dev,
> return 0;
> }
>
> +#define FSL_MC_GCR1 0x0
> +#define GCR1_P1_STOP BIT(31)
> +
> +static u32 boot_gcr1;
> +static void __iomem *fsl_mc_regs;
> +
> /**
> * fsl_mc_bus_probe - callback invoked when the root MC bus is being
> * added
> @@ -906,6 +914,21 @@ static int fsl_mc_bus_probe(struct platform_device *pdev)
> struct mc_version mc_version;
> struct resource res;
>
> + /*
> + * The MC firmware requires full access to the whole address space plus
> + * it has no way of dealing with any kind of address translation, so
> + * request direct mapping for it.
> + */
> + error = iommu_request_dm_for_dev(&pdev->dev);
> + if (error)
> + dev_warn(&pdev->dev, "iommu_request_dm_for_dev() failed: %d\n",
> + error);
> +
> + if (fsl_mc_regs) {
> + /* Resume the firmware */
> + writel(boot_gcr1 & ~GCR1_P1_STOP, fsl_mc_regs + FSL_MC_GCR1);
> + }
> +
> mc = devm_kzalloc(&pdev->dev, sizeof(*mc), GFP_KERNEL);
> if (!mc)
> return -ENOMEM;
> @@ -990,6 +1013,13 @@ static int fsl_mc_bus_remove(struct platform_device *pdev)
> if (!fsl_mc_is_root_dprc(&mc->root_mc_bus_dev->dev))
> return -EINVAL;
>
> + /*
> + * Pause back the firmware so that it doesn't trigger faults by the
> + * time SMMU gets brought down.
> + */
> + writel(boot_gcr1 | GCR1_P1_STOP, fsl_mc_regs + FSL_MC_GCR1);
> + iounmap(fsl_mc_regs);
> +
> fsl_mc_device_remove(mc->root_mc_bus_dev);
>
> fsl_destroy_mc_io(mc->root_mc_bus_dev->mc_io);
> @@ -1018,6 +1048,8 @@ static struct platform_driver fsl_mc_bus_driver = {
> static int __init fsl_mc_bus_driver_init(void)
> {
> int error;
> + struct device_node *np;
> + struct resource res;
>
> error = bus_register(&fsl_mc_bus_type);
> if (error < 0) {
> @@ -1039,9 +1071,30 @@ static int __init fsl_mc_bus_driver_init(void)
> if (error < 0)
> goto error_cleanup_dprc_driver;
>
> + np = of_find_matching_node(NULL, fsl_mc_bus_match_table);
> + if (np && of_device_is_available(np)) {
> + error = of_address_to_resource(np, 1, &res);
> + if (error)
> + goto error_cleanup_dprc_driver;
> + fsl_mc_regs = ioremap(res.start, resource_size(&res));
> + if (!fsl_mc_regs) {
> + error = -ENXIO;
> + goto error_cleanup_dprc_driver;
> + }
> +
> + boot_gcr1 = readl(fsl_mc_regs + FSL_MC_GCR1);
> + /*
> + * If found running, pause MC firmware in order to get a chance
> + * to setup SMMU for it.
> + */
> + if (!(boot_gcr1 & GCR1_P1_STOP))
> + writel(boot_gcr1 | GCR1_P1_STOP, fsl_mc_regs + FSL_MC_GCR1);
> + }
> +
> return 0;
>
> error_cleanup_dprc_driver:
> + iounmap(fsl_mc_regs);
> dprc_driver_exit();
>
> error_cleanup_driver:
> --
> 2.17.1
>
--
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up
According to speedtest.net: 11.9Mbps down 500kbps up
_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH] iommu: silence iommu group prints
2020-03-04 10:07 ` Russell King - ARM Linux admin
@ 2020-03-04 10:33 ` Laurentiu Tudor
2020-03-04 10:52 ` Russell King - ARM Linux admin
0 siblings, 1 reply; 24+ messages in thread
From: Laurentiu Tudor @ 2020-03-04 10:33 UTC (permalink / raw)
To: Russell King - ARM Linux admin, Olof Johansson
Cc: Diana Madalina Craciun, iommu, Robin Murphy, Ioana Ciornei
On 04.03.2020 12:07, Russell King - ARM Linux admin wrote:
> On Wed, Mar 04, 2020 at 11:56:53AM +0200, Laurentiu Tudor wrote:
>> From 44ae46501b5379bd0890df87fd3827248626ed03 Mon Sep 17 00:00:00 2001
>> From: Laurentiu Tudor <laurentiu.tudor@nxp.com>
>> Date: Tue, 1 Oct 2019 16:22:48 +0300
>> Subject: [PATCH 1/6] bus: fsl-mc: make mc work with smmu disable bypass on
>> Content-Type: text/plain; charset="us-ascii"
>>
>> Since this commit [1] booting kernel on MC based chips started to
>> fail because this firmware starts before the kernel and as soon as
>> SMMU is probed it starts to trigger contiguous faults.
>
> I think you mean "continuous" here.
Yes, thanks.
>> This is a workaround that allows MC firmware to run with SMMU
>> in disable bypass mode. It consists of the following steps:
>> 1. pause the firmware at early boot to get a chance to setup SMMU
>> 2. request direct mapping for MC device
>> 3. resume the firmware
>> The workaround relies on the fact that no state is lost when
>> pausing / resuming firmware, as per the docs.
>> With this patch, platforms with MC firmware can now boot without
>> having to change the default config to set:
>> CONFIG_ARM_SMMU_DISABLE_BYPASS_BY_DEFAULT=n
>
> This alone is a definite improvement, and has been needed for a while.
> Please submit this patch with an appropriate Fixes: tag so stable trees
> can pick it up.
The thing is that probably this workaround will never make it in the
kernel because it questionable to say the least, e.g. see [1]. My plan
is to give this approach [2] a try sometime soon.
[1] https://patchwork.kernel.org/comment/23149049/
[2] https://patchwork.kernel.org/cover/11279577/
---
Best Regards, Laurentiu
>> [1] 954a03be033 ("iommu/arm-smmu: Break insecure users by disabling bypass by default")
>
> Please put this where you're referencing it above - it's fine to wrap
> the description of the commit when using it in the body of the commit
> message. However, that should _never_ when providing a Fixes: tag
> (linux-next has a script which will detect and complain about broken
> Fixes: tags.)
>
> Thanks.
>
>>
>> Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
>> ---
>> drivers/bus/fsl-mc/fsl-mc-bus.c | 53 +++++++++++++++++++++++++++++++++
>> 1 file changed, 53 insertions(+)
>>
>> diff --git a/drivers/bus/fsl-mc/fsl-mc-bus.c b/drivers/bus/fsl-mc/fsl-mc-bus.c
>> index a0f8854acb3a..683a6401ffe8 100644
>> --- a/drivers/bus/fsl-mc/fsl-mc-bus.c
>> +++ b/drivers/bus/fsl-mc/fsl-mc-bus.c
>> @@ -18,6 +18,8 @@
>> #include <linux/bitops.h>
>> #include <linux/msi.h>
>> #include <linux/dma-mapping.h>
>> +#include <linux/iommu.h>
>> +#include <linux/io.h>
>>
>> #include "fsl-mc-private.h"
>>
>> @@ -889,6 +891,12 @@ static int get_mc_addr_translation_ranges(struct device *dev,
>> return 0;
>> }
>>
>> +#define FSL_MC_GCR1 0x0
>> +#define GCR1_P1_STOP BIT(31)
>> +
>> +static u32 boot_gcr1;
>> +static void __iomem *fsl_mc_regs;
>> +
>> /**
>> * fsl_mc_bus_probe - callback invoked when the root MC bus is being
>> * added
>> @@ -906,6 +914,21 @@ static int fsl_mc_bus_probe(struct platform_device *pdev)
>> struct mc_version mc_version;
>> struct resource res;
>>
>> + /*
>> + * The MC firmware requires full access to the whole address space plus
>> + * it has no way of dealing with any kind of address translation, so
>> + * request direct mapping for it.
>> + */
>> + error = iommu_request_dm_for_dev(&pdev->dev);
>> + if (error)
>> + dev_warn(&pdev->dev, "iommu_request_dm_for_dev() failed: %d\n",
>> + error);
>> +
>> + if (fsl_mc_regs) {
>> + /* Resume the firmware */
>> + writel(boot_gcr1 & ~GCR1_P1_STOP, fsl_mc_regs + FSL_MC_GCR1);
>> + }
>> +
>> mc = devm_kzalloc(&pdev->dev, sizeof(*mc), GFP_KERNEL);
>> if (!mc)
>> return -ENOMEM;
>> @@ -990,6 +1013,13 @@ static int fsl_mc_bus_remove(struct platform_device *pdev)
>> if (!fsl_mc_is_root_dprc(&mc->root_mc_bus_dev->dev))
>> return -EINVAL;
>>
>> + /*
>> + * Pause back the firmware so that it doesn't trigger faults by the
>> + * time SMMU gets brought down.
>> + */
>> + writel(boot_gcr1 | GCR1_P1_STOP, fsl_mc_regs + FSL_MC_GCR1);
>> + iounmap(fsl_mc_regs);
>> +
>> fsl_mc_device_remove(mc->root_mc_bus_dev);
>>
>> fsl_destroy_mc_io(mc->root_mc_bus_dev->mc_io);
>> @@ -1018,6 +1048,8 @@ static struct platform_driver fsl_mc_bus_driver = {
>> static int __init fsl_mc_bus_driver_init(void)
>> {
>> int error;
>> + struct device_node *np;
>> + struct resource res;
>>
>> error = bus_register(&fsl_mc_bus_type);
>> if (error < 0) {
>> @@ -1039,9 +1071,30 @@ static int __init fsl_mc_bus_driver_init(void)
>> if (error < 0)
>> goto error_cleanup_dprc_driver;
>>
>> + np = of_find_matching_node(NULL, fsl_mc_bus_match_table);
>> + if (np && of_device_is_available(np)) {
>> + error = of_address_to_resource(np, 1, &res);
>> + if (error)
>> + goto error_cleanup_dprc_driver;
>> + fsl_mc_regs = ioremap(res.start, resource_size(&res));
>> + if (!fsl_mc_regs) {
>> + error = -ENXIO;
>> + goto error_cleanup_dprc_driver;
>> + }
>> +
>> + boot_gcr1 = readl(fsl_mc_regs + FSL_MC_GCR1);
>> + /*
>> + * If found running, pause MC firmware in order to get a chance
>> + * to setup SMMU for it.
>> + */
>> + if (!(boot_gcr1 & GCR1_P1_STOP))
>> + writel(boot_gcr1 | GCR1_P1_STOP, fsl_mc_regs + FSL_MC_GCR1);
>> + }
>> +
>> return 0;
>>
>> error_cleanup_dprc_driver:
>> + iounmap(fsl_mc_regs);
>> dprc_driver_exit();
>>
>> error_cleanup_driver:
>> --
>> 2.17.1
>>
>
>
_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH] iommu: silence iommu group prints
2020-03-04 10:33 ` Laurentiu Tudor
@ 2020-03-04 10:52 ` Russell King - ARM Linux admin
2020-03-04 11:26 ` Laurentiu Tudor
0 siblings, 1 reply; 24+ messages in thread
From: Russell King - ARM Linux admin @ 2020-03-04 10:52 UTC (permalink / raw)
To: Laurentiu Tudor
Cc: Diana Madalina Craciun, iommu, Ioana Ciornei, Robin Murphy
On Wed, Mar 04, 2020 at 12:33:14PM +0200, Laurentiu Tudor wrote:
>
>
> On 04.03.2020 12:07, Russell King - ARM Linux admin wrote:
> > On Wed, Mar 04, 2020 at 11:56:53AM +0200, Laurentiu Tudor wrote:
> > > From 44ae46501b5379bd0890df87fd3827248626ed03 Mon Sep 17 00:00:00 2001
> > > From: Laurentiu Tudor <laurentiu.tudor@nxp.com>
> > > Date: Tue, 1 Oct 2019 16:22:48 +0300
> > > Subject: [PATCH 1/6] bus: fsl-mc: make mc work with smmu disable bypass on
> > > Content-Type: text/plain; charset="us-ascii"
> > >
> > > Since this commit [1] booting kernel on MC based chips started to
> > > fail because this firmware starts before the kernel and as soon as
> > > SMMU is probed it starts to trigger contiguous faults.
> >
> > I think you mean "continuous" here.
>
> Yes, thanks.
>
> > > This is a workaround that allows MC firmware to run with SMMU
> > > in disable bypass mode. It consists of the following steps:
> > > 1. pause the firmware at early boot to get a chance to setup SMMU
> > > 2. request direct mapping for MC device
> > > 3. resume the firmware
> > > The workaround relies on the fact that no state is lost when
> > > pausing / resuming firmware, as per the docs.
> > > With this patch, platforms with MC firmware can now boot without
> > > having to change the default config to set:
> > > CONFIG_ARM_SMMU_DISABLE_BYPASS_BY_DEFAULT=n
> >
> > This alone is a definite improvement, and has been needed for a while.
> > Please submit this patch with an appropriate Fixes: tag so stable trees
> > can pick it up.
>
> The thing is that probably this workaround will never make it in the kernel
> because it questionable to say the least, e.g. see [1]. My plan is to give
> this approach [2] a try sometime soon.
>
> [1] https://patchwork.kernel.org/comment/23149049/
> [2] https://patchwork.kernel.org/cover/11279577/
So, if we want to reduce the iommu noise, we need to completely break
the ability to use a mainline kernel on the LX2160A. This doesn't
seem practical nor sensible. Someone has to give.
--
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up
According to speedtest.net: 11.9Mbps down 500kbps up
_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH] iommu: silence iommu group prints
2020-03-04 10:52 ` Russell King - ARM Linux admin
@ 2020-03-04 11:26 ` Laurentiu Tudor
0 siblings, 0 replies; 24+ messages in thread
From: Laurentiu Tudor @ 2020-03-04 11:26 UTC (permalink / raw)
To: Russell King - ARM Linux admin
Cc: Diana Madalina Craciun, iommu, Ioana Ciornei, Robin Murphy
On 04.03.2020 12:52, Russell King - ARM Linux admin wrote:
> On Wed, Mar 04, 2020 at 12:33:14PM +0200, Laurentiu Tudor wrote:
>>
>>
>> On 04.03.2020 12:07, Russell King - ARM Linux admin wrote:
>>> On Wed, Mar 04, 2020 at 11:56:53AM +0200, Laurentiu Tudor wrote:
>>>> From 44ae46501b5379bd0890df87fd3827248626ed03 Mon Sep 17 00:00:00 2001
>>>> From: Laurentiu Tudor <laurentiu.tudor@nxp.com>
>>>> Date: Tue, 1 Oct 2019 16:22:48 +0300
>>>> Subject: [PATCH 1/6] bus: fsl-mc: make mc work with smmu disable bypass on
>>>> Content-Type: text/plain; charset="us-ascii"
>>>>
>>>> Since this commit [1] booting kernel on MC based chips started to
>>>> fail because this firmware starts before the kernel and as soon as
>>>> SMMU is probed it starts to trigger contiguous faults.
>>>
>>> I think you mean "continuous" here.
>>
>> Yes, thanks.
>>
>>>> This is a workaround that allows MC firmware to run with SMMU
>>>> in disable bypass mode. It consists of the following steps:
>>>> 1. pause the firmware at early boot to get a chance to setup SMMU
>>>> 2. request direct mapping for MC device
>>>> 3. resume the firmware
>>>> The workaround relies on the fact that no state is lost when
>>>> pausing / resuming firmware, as per the docs.
>>>> With this patch, platforms with MC firmware can now boot without
>>>> having to change the default config to set:
>>>> CONFIG_ARM_SMMU_DISABLE_BYPASS_BY_DEFAULT=n
>>>
>>> This alone is a definite improvement, and has been needed for a while.
>>> Please submit this patch with an appropriate Fixes: tag so stable trees
>>> can pick it up.
>>
>> The thing is that probably this workaround will never make it in the kernel
>> because it questionable to say the least, e.g. see [1]. My plan is to give
>> this approach [2] a try sometime soon.
>>
> So, if we want to reduce the iommu noise, we need to completely break
> the ability to use a mainline kernel on the LX2160A. This doesn't
> seem practical nor sensible. Someone has to give.
>
Well, I think it's a bit too early for such conclusions. I'd consider
this stuff early / experimental work, probably will take quite a while
for the dust to settle. Anyway, I'll take care not to break the kernel
when I'll start submitting more official patches.
For now, I'm just hoping that this stuff helps fixing your local tree.
---
Best Regards, Laurentiu
_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu
^ permalink raw reply [flat|nested] 24+ messages in thread
end of thread, other threads:[~2020-03-04 11:27 UTC | newest]
Thread overview: 24+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-02-27 11:57 [PATCH] iommu: silence iommu group prints Russell King
2020-02-27 13:44 ` Robin Murphy
2020-02-27 13:48 ` Russell King - ARM Linux admin
2020-02-27 18:19 ` Robin Murphy
2020-02-27 19:00 ` Russell King - ARM Linux admin
2020-02-28 2:16 ` Lu Baolu
2020-02-28 9:33 ` John Garry
2020-02-28 10:06 ` Russell King - ARM Linux admin
2020-02-28 18:32 ` Robin Murphy
2020-03-02 11:48 ` Laurentiu Tudor
2020-03-03 14:18 ` Laurentiu Tudor
2020-03-03 15:49 ` Russell King - ARM Linux admin
2020-03-03 15:55 ` Laurentiu Tudor
2020-03-03 22:17 ` Russell King - ARM Linux admin
2020-03-04 8:56 ` Laurentiu Tudor
2020-03-04 9:33 ` Russell King - ARM Linux admin
2020-03-04 9:42 ` Laurentiu Tudor
2020-03-04 9:51 ` Russell King - ARM Linux admin
2020-03-04 9:56 ` Laurentiu Tudor
2020-03-04 10:07 ` Russell King - ARM Linux admin
2020-03-04 10:33 ` Laurentiu Tudor
2020-03-04 10:52 ` Russell King - ARM Linux admin
2020-03-04 11:26 ` Laurentiu Tudor
2020-03-02 15:44 ` Joerg Roedel
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.