* [PATCH 0/3] Document r8a77990 DRIF support
@ 2020-09-15 13:12 Fabrizio Castro
2020-09-15 13:12 ` [PATCH 1/3] MAINTAINERS: Add Fabrizio Castro to Renesas DRIF Fabrizio Castro
` (2 more replies)
0 siblings, 3 replies; 12+ messages in thread
From: Fabrizio Castro @ 2020-09-15 13:12 UTC (permalink / raw)
To: Mauro Carvalho Chehab, Rob Herring, Geert Uytterhoeven
Cc: Fabrizio Castro, Ramesh Shanmugasundaram, linux-media,
devicetree, linux-kernel, linux-renesas-soc, Chris Paterson,
Biju Das, Prabhakar Mahadev Lad, Laurent Pinchart
Dear All,
this series documents DRIF support for the r8a77990
(a.k.a. R-Car E3).
Thanks,
Fab
Fabrizio Castro (3):
MAINTAINERS: Add Fabrizio Castro to Renesas DRIF
media: dt-bindings: media: renesas,drif: Convert to json-schema
media: dt-bindings: media: renesas,drif: Add r8a77990 support
.../bindings/media/renesas,drif.txt | 177 ------------
.../bindings/media/renesas,drif.yaml | 271 ++++++++++++++++++
MAINTAINERS | 3 +-
3 files changed, 273 insertions(+), 178 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/media/renesas,drif.txt
create mode 100644 Documentation/devicetree/bindings/media/renesas,drif.yaml
--
2.25.1
^ permalink raw reply [flat|nested] 12+ messages in thread* [PATCH 1/3] MAINTAINERS: Add Fabrizio Castro to Renesas DRIF 2020-09-15 13:12 [PATCH 0/3] Document r8a77990 DRIF support Fabrizio Castro @ 2020-09-15 13:12 ` Fabrizio Castro 2020-09-15 16:11 ` Laurent Pinchart 2020-09-15 13:12 ` [PATCH 2/3] media: dt-bindings: media: renesas,drif: Convert to json-schema Fabrizio Castro 2020-09-15 13:12 ` [PATCH 3/3] media: dt-bindings: media: renesas,drif: Add r8a77990 support Fabrizio Castro 2 siblings, 1 reply; 12+ messages in thread From: Fabrizio Castro @ 2020-09-15 13:12 UTC (permalink / raw) To: Mauro Carvalho Chehab, Rob Herring, Geert Uytterhoeven Cc: Fabrizio Castro, Ramesh Shanmugasundaram, linux-media, devicetree, linux-kernel, linux-renesas-soc, Chris Paterson, Biju Das, Prabhakar Mahadev Lad, Laurent Pinchart Renesas are expanding their DRIF support and offering, I'll be the internal maintainer for DRIF. Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com> --- MAINTAINERS | 1 + 1 file changed, 1 insertion(+) diff --git a/MAINTAINERS b/MAINTAINERS index 26af84f97353..9f49e5ac90d8 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -10898,6 +10898,7 @@ F: include/media/drv-intf/renesas-ceu.h MEDIA DRIVERS FOR RENESAS - DRIF M: Ramesh Shanmugasundaram <rashanmu@gmail.com> +M: Fabrizio Castro <fabrizio.castro.jz@renesas.com> L: linux-media@vger.kernel.org L: linux-renesas-soc@vger.kernel.org S: Supported -- 2.25.1 ^ permalink raw reply related [flat|nested] 12+ messages in thread
* Re: [PATCH 1/3] MAINTAINERS: Add Fabrizio Castro to Renesas DRIF 2020-09-15 13:12 ` [PATCH 1/3] MAINTAINERS: Add Fabrizio Castro to Renesas DRIF Fabrizio Castro @ 2020-09-15 16:11 ` Laurent Pinchart 0 siblings, 0 replies; 12+ messages in thread From: Laurent Pinchart @ 2020-09-15 16:11 UTC (permalink / raw) To: Fabrizio Castro Cc: Mauro Carvalho Chehab, Rob Herring, Geert Uytterhoeven, Ramesh Shanmugasundaram, linux-media, devicetree, linux-kernel, linux-renesas-soc, Chris Paterson, Biju Das, Prabhakar Mahadev Lad Hi Fabrizio, Thank you for the patch. On Tue, Sep 15, 2020 at 02:12:14PM +0100, Fabrizio Castro wrote: > Renesas are expanding their DRIF support and offering, > I'll be the internal maintainer for DRIF. > > Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com> Thank you for volunteering :-) Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> > --- > MAINTAINERS | 1 + > 1 file changed, 1 insertion(+) > > diff --git a/MAINTAINERS b/MAINTAINERS > index 26af84f97353..9f49e5ac90d8 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -10898,6 +10898,7 @@ F: include/media/drv-intf/renesas-ceu.h > > MEDIA DRIVERS FOR RENESAS - DRIF > M: Ramesh Shanmugasundaram <rashanmu@gmail.com> > +M: Fabrizio Castro <fabrizio.castro.jz@renesas.com> > L: linux-media@vger.kernel.org > L: linux-renesas-soc@vger.kernel.org > S: Supported -- Regards, Laurent Pinchart ^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH 2/3] media: dt-bindings: media: renesas,drif: Convert to json-schema 2020-09-15 13:12 [PATCH 0/3] Document r8a77990 DRIF support Fabrizio Castro 2020-09-15 13:12 ` [PATCH 1/3] MAINTAINERS: Add Fabrizio Castro to Renesas DRIF Fabrizio Castro @ 2020-09-15 13:12 ` Fabrizio Castro 2020-09-15 14:12 ` Lad, Prabhakar 2020-09-15 17:36 ` Laurent Pinchart 2020-09-15 13:12 ` [PATCH 3/3] media: dt-bindings: media: renesas,drif: Add r8a77990 support Fabrizio Castro 2 siblings, 2 replies; 12+ messages in thread From: Fabrizio Castro @ 2020-09-15 13:12 UTC (permalink / raw) To: Mauro Carvalho Chehab, Rob Herring, Geert Uytterhoeven Cc: Fabrizio Castro, Ramesh Shanmugasundaram, linux-media, devicetree, linux-kernel, linux-renesas-soc, Chris Paterson, Biju Das, Prabhakar Mahadev Lad, Laurent Pinchart Convert the Renesas DRIF bindings to DT schema and update MAINTAINERS accordingly. Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com> --- .../bindings/media/renesas,drif.txt | 177 ------------ .../bindings/media/renesas,drif.yaml | 270 ++++++++++++++++++ MAINTAINERS | 2 +- 3 files changed, 271 insertions(+), 178 deletions(-) delete mode 100644 Documentation/devicetree/bindings/media/renesas,drif.txt create mode 100644 Documentation/devicetree/bindings/media/renesas,drif.yaml diff --git a/Documentation/devicetree/bindings/media/renesas,drif.txt b/Documentation/devicetree/bindings/media/renesas,drif.txt deleted file mode 100644 index 0d8974aa8b38..000000000000 --- a/Documentation/devicetree/bindings/media/renesas,drif.txt +++ /dev/null @@ -1,177 +0,0 @@ -Renesas R-Car Gen3 Digital Radio Interface controller (DRIF) ------------------------------------------------------------- - -R-Car Gen3 DRIF is a SPI like receive only slave device. A general -representation of DRIF interfacing with a master device is shown below. - -+---------------------+ +---------------------+ -| |-----SCK------->|CLK | -| Master |-----SS-------->|SYNC DRIFn (slave) | -| |-----SD0------->|D0 | -| |-----SD1------->|D1 | -+---------------------+ +---------------------+ - -As per datasheet, each DRIF channel (drifn) is made up of two internal -channels (drifn0 & drifn1). These two internal channels share the common -CLK & SYNC. Each internal channel has its own dedicated resources like -irq, dma channels, address space & clock. This internal split is not -visible to the external master device. - -The device tree model represents each internal channel as a separate node. -The internal channels sharing the CLK & SYNC are tied together by their -phandles using a property called "renesas,bonding". For the rest of -the documentation, unless explicitly stated, the word channel implies an -internal channel. - -When both internal channels are enabled they need to be managed together -as one (i.e.) they cannot operate alone as independent devices. Out of the -two, one of them needs to act as a primary device that accepts common -properties of both the internal channels. This channel is identified by a -property called "renesas,primary-bond". - -To summarize, - - When both the internal channels that are bonded together are enabled, - the zeroth channel is selected as primary-bond. This channels accepts - properties common to all the members of the bond. - - When only one of the bonded channels need to be enabled, the property - "renesas,bonding" or "renesas,primary-bond" will have no effect. That - enabled channel can act alone as any other independent device. - -Required properties of an internal channel: -------------------------------------------- -- compatible: "renesas,r8a7795-drif" if DRIF controller is a part of R8A7795 SoC. - "renesas,r8a7796-drif" if DRIF controller is a part of R8A7796 SoC. - "renesas,rcar-gen3-drif" for a generic R-Car Gen3 compatible device. - - When compatible with the generic version, nodes must list the - SoC-specific version corresponding to the platform first - followed by the generic version. - -- reg: offset and length of that channel. -- interrupts: associated with that channel. -- clocks: phandle and clock specifier of that channel. -- clock-names: clock input name string: "fck". -- dmas: phandles to the DMA channels. -- dma-names: names of the DMA channel: "rx". -- renesas,bonding: phandle to the other channel. - -Optional properties of an internal channel: -------------------------------------------- -- power-domains: phandle to the respective power domain. - -Required properties of an internal channel when: - - It is the only enabled channel of the bond (or) - - If it acts as primary among enabled bonds --------------------------------------------------------- -- pinctrl-0: pin control group to be used for this channel. -- pinctrl-names: must be "default". -- renesas,primary-bond: empty property indicating the channel acts as primary - among the bonded channels. -- port: child port node corresponding to the data input, in accordance with - the video interface bindings defined in - Documentation/devicetree/bindings/media/video-interfaces.txt. The port - node must contain at least one endpoint. - -Optional endpoint property: ---------------------------- -- sync-active: Indicates sync signal polarity, 0/1 for low/high respectively. - This property maps to SYNCAC bit in the hardware manual. The - default is 1 (active high). - -Example: --------- - -(1) Both internal channels enabled: ------------------------------------ - -When interfacing with a third party tuner device with two data pins as shown -below. - -+---------------------+ +---------------------+ -| |-----SCK------->|CLK | -| Master |-----SS-------->|SYNC DRIFn (slave) | -| |-----SD0------->|D0 | -| |-----SD1------->|D1 | -+---------------------+ +---------------------+ - - drif00: rif@e6f40000 { - compatible = "renesas,r8a7795-drif", - "renesas,rcar-gen3-drif"; - reg = <0 0xe6f40000 0 0x64>; - interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cpg CPG_MOD 515>; - clock-names = "fck"; - dmas = <&dmac1 0x20>, <&dmac2 0x20>; - dma-names = "rx", "rx"; - power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; - renesas,bonding = <&drif01>; - renesas,primary-bond; - pinctrl-0 = <&drif0_pins>; - pinctrl-names = "default"; - port { - drif0_ep: endpoint { - remote-endpoint = <&tuner_ep>; - }; - }; - }; - - drif01: rif@e6f50000 { - compatible = "renesas,r8a7795-drif", - "renesas,rcar-gen3-drif"; - reg = <0 0xe6f50000 0 0x64>; - interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cpg CPG_MOD 514>; - clock-names = "fck"; - dmas = <&dmac1 0x22>, <&dmac2 0x22>; - dma-names = "rx", "rx"; - power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; - renesas,bonding = <&drif00>; - }; - - -(2) Internal channel 1 alone is enabled: ----------------------------------------- - -When interfacing with a third party tuner device with one data pin as shown -below. - -+---------------------+ +---------------------+ -| |-----SCK------->|CLK | -| Master |-----SS-------->|SYNC DRIFn (slave) | -| | |D0 (unused) | -| |-----SD-------->|D1 | -+---------------------+ +---------------------+ - - drif00: rif@e6f40000 { - compatible = "renesas,r8a7795-drif", - "renesas,rcar-gen3-drif"; - reg = <0 0xe6f40000 0 0x64>; - interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cpg CPG_MOD 515>; - clock-names = "fck"; - dmas = <&dmac1 0x20>, <&dmac2 0x20>; - dma-names = "rx", "rx"; - power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; - renesas,bonding = <&drif01>; - }; - - drif01: rif@e6f50000 { - compatible = "renesas,r8a7795-drif", - "renesas,rcar-gen3-drif"; - reg = <0 0xe6f50000 0 0x64>; - interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cpg CPG_MOD 514>; - clock-names = "fck"; - dmas = <&dmac1 0x22>, <&dmac2 0x22>; - dma-names = "rx", "rx"; - power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; - renesas,bonding = <&drif00>; - pinctrl-0 = <&drif0_pins>; - pinctrl-names = "default"; - port { - drif0_ep: endpoint { - remote-endpoint = <&tuner_ep>; - sync-active = <0>; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/media/renesas,drif.yaml b/Documentation/devicetree/bindings/media/renesas,drif.yaml new file mode 100644 index 000000000000..f57fccc159d6 --- /dev/null +++ b/Documentation/devicetree/bindings/media/renesas,drif.yaml @@ -0,0 +1,270 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/renesas,drif.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas R-Car Gen3 Digital Radio Interface controller (DRIF) + +maintainers: + - Ramesh Shanmugasundaram <rashanmu@gmail.com> + - Fabrizio Castro <fabrizio.castro.jz@renesas.com> + +description: | + R-Car Gen3 DRIF is a SPI like receive only slave device. A general + representation of DRIF interfacing with a master device is shown below. + + +---------------------+ +---------------------+ + | |-----SCK------->|CLK | + | Master |-----SS-------->|SYNC DRIFn (slave) | + | |-----SD0------->|D0 | + | |-----SD1------->|D1 | + +---------------------+ +---------------------+ + + As per datasheet, each DRIF channel (drifn) is made up of two internal + channels (drifn0 & drifn1). These two internal channels share the common + CLK & SYNC. Each internal channel has its own dedicated resources like + irq, dma channels, address space & clock. This internal split is not + visible to the external master device. + + The device tree model represents each internal channel as a separate node. + The internal channels sharing the CLK & SYNC are tied together by their + phandles using a property called "renesas,bonding". For the rest of + the documentation, unless explicitly stated, the word channel implies an + internal channel. + + When both internal channels are enabled they need to be managed together + as one (i.e.) they cannot operate alone as independent devices. Out of the + two, one of them needs to act as a primary device that accepts common + properties of both the internal channels. This channel is identified by a + property called "renesas,primary-bond". + + To summarize, + * When both the internal channels that are bonded together are enabled, + the zeroth channel is selected as primary-bond. This channels accepts + properties common to all the members of the bond. + * When only one of the bonded channels need to be enabled, the property + "renesas,bonding" or "renesas,primary-bond" will have no effect. That + enabled channel can act alone as any other independent device. + +properties: + compatible: + items: + - enum: + - renesas,r8a7795-drif # R-Car H3 + - renesas,r8a7796-drif # R-Car M3-W + - const: renesas,rcar-gen3-drif # Generic R-Car Gen3 compatible device + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + maxItems: 1 + items: + - const: fck + + resets: + maxItems: 1 + + dmas: + minItems: 1 + maxItems: 2 + + dma-names: + minItems: 1 + maxItems: 2 + items: + - const: rx + - const: rx + + renesas,bonding: + $ref: /schemas/types.yaml#/definitions/phandle + description: + The phandle to the other internal channel of DRIF + + power-domains: + maxItems: 1 + + pinctrl-0: + maxItems: 1 + + pinctrl-names: + maxItems: 1 + items: + - const: default + + renesas,primary-bond: + type: boolean + description: + Indicates that the channel acts as primary among the bonded channels. + + port: + type: object + description: + Child port node corresponding to the data input, in accordance with the + video interface bindings defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. + The port node must contain at least one endpoint. + + properties: + endpoint: + type: object + + properties: + remote-endpoint: + description: + A phandle to the remote tuner endpoint subnode in remote node + port. + + sync-active: + enum: [0, 1] + description: + Indicates sync signal polarity, 0/1 for low/high respectively. + This property maps to SYNCAC bit in the hardware manual. The + default is 1 (active high). + + additionalProperties: false + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - resets + - dmas + - dma-names + - renesas,bonding + +if: + required: + - renesas,primary-bond +then: + required: + - pinctrl-0 + - pinctrl-names + - port + +additionalProperties: false + +examples: + # Example with both internal channels enabled. + # + # When interfacing with a third party tuner device with two data pins as shown + # below. + # + # +---------------------+ +---------------------+ + # | |-----SCK------->|CLK | + # | Master |-----SS-------->|SYNC DRIFn (slave) | + # | |-----SD0------->|D0 | + # | |-----SD1------->|D1 | + # +---------------------+ +---------------------+ + - | + #include <dt-bindings/clock/r8a7795-cpg-mssr.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/r8a7795-sysc.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + drif00: rif@e6f40000 { + compatible = "renesas,r8a7795-drif", + "renesas,rcar-gen3-drif"; + reg = <0 0xe6f40000 0 0x64>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 515>; + clock-names = "fck"; + dmas = <&dmac1 0x20>, <&dmac2 0x20>; + dma-names = "rx", "rx"; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + renesas,bonding = <&drif01>; + resets = <&cpg 515>; + renesas,primary-bond; + pinctrl-0 = <&drif0_pins>; + pinctrl-names = "default"; + port { + drif0_ep: endpoint { + remote-endpoint = <&tuner_ep>; + }; + }; + }; + + drif01: rif@e6f50000 { + compatible = "renesas,r8a7795-drif", + "renesas,rcar-gen3-drif"; + reg = <0 0xe6f50000 0 0x64>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 514>; + clock-names = "fck"; + dmas = <&dmac1 0x22>, <&dmac2 0x22>; + dma-names = "rx", "rx"; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + renesas,bonding = <&drif00>; + resets = <&cpg 514>; + }; + }; + + # Example with internal channel 1 alone enabled. + # + # When interfacing with a third party tuner device with one data pin as shown + # below. + # + # +---------------------+ +---------------------+ + # | |-----SCK------->|CLK | + # | Master |-----SS-------->|SYNC DRIFn (slave) | + # | | |D0 (unused) | + # | |-----SD-------->|D1 | + # +---------------------+ +---------------------+ + - | + #include <dt-bindings/clock/r8a7795-cpg-mssr.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/r8a7795-sysc.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + drif10: rif@e6f60000 { + compatible = "renesas,r8a7795-drif", + "renesas,rcar-gen3-drif"; + reg = <0 0xe6f60000 0 0x64>; + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 513>; + clock-names = "fck"; + dmas = <&dmac1 0x24>, <&dmac2 0x24>; + dma-names = "rx", "rx"; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 513>; + renesas,bonding = <&drif11>; + }; + + drif11: rif@e6f70000 { + compatible = "renesas,r8a7795-drif", + "renesas,rcar-gen3-drif"; + reg = <0 0xe6f70000 0 0x64>; + interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 512>; + clock-names = "fck"; + dmas = <&dmac1 0x26>, <&dmac2 0x26>; + dma-names = "rx", "rx"; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 512>; + renesas,bonding = <&drif10>; + pinctrl-0 = <&drif1_pins>; + pinctrl-names = "default"; + port { + drif1_ep: endpoint { + remote-endpoint = <&tuner_ep1>; + sync-active = <0>; + }; + }; + }; + }; +... diff --git a/MAINTAINERS b/MAINTAINERS index 9f49e5ac90d8..3e2a1cad3749 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -10903,7 +10903,7 @@ L: linux-media@vger.kernel.org L: linux-renesas-soc@vger.kernel.org S: Supported T: git git://linuxtv.org/media_tree.git -F: Documentation/devicetree/bindings/media/renesas,drif.txt +F: Documentation/devicetree/bindings/media/renesas,drif.yaml F: drivers/media/platform/rcar_drif.c MEDIA DRIVERS FOR RENESAS - FCP -- 2.25.1 ^ permalink raw reply related [flat|nested] 12+ messages in thread
* Re: [PATCH 2/3] media: dt-bindings: media: renesas,drif: Convert to json-schema 2020-09-15 13:12 ` [PATCH 2/3] media: dt-bindings: media: renesas,drif: Convert to json-schema Fabrizio Castro @ 2020-09-15 14:12 ` Lad, Prabhakar 2020-09-15 17:36 ` Laurent Pinchart 1 sibling, 0 replies; 12+ messages in thread From: Lad, Prabhakar @ 2020-09-15 14:12 UTC (permalink / raw) To: Fabrizio Castro Cc: Mauro Carvalho Chehab, Rob Herring, Geert Uytterhoeven, Ramesh Shanmugasundaram, linux-media, open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS, LKML, Linux-Renesas, Chris Paterson, Biju Das, Prabhakar Mahadev Lad, Laurent Pinchart Hi Fabrizio, Thank you for the patch. On Tue, Sep 15, 2020 at 2:14 PM Fabrizio Castro <fabrizio.castro.jz@renesas.com> wrote: > > Convert the Renesas DRIF bindings to DT schema and update > MAINTAINERS accordingly. > > Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com> > --- > .../bindings/media/renesas,drif.txt | 177 ------------ > .../bindings/media/renesas,drif.yaml | 270 ++++++++++++++++++ > MAINTAINERS | 2 +- > 3 files changed, 271 insertions(+), 178 deletions(-) > delete mode 100644 Documentation/devicetree/bindings/media/renesas,drif.txt > create mode 100644 Documentation/devicetree/bindings/media/renesas,drif.yaml > Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Cheers, Prabhakar > diff --git a/Documentation/devicetree/bindings/media/renesas,drif.txt b/Documentation/devicetree/bindings/media/renesas,drif.txt > deleted file mode 100644 > index 0d8974aa8b38..000000000000 > --- a/Documentation/devicetree/bindings/media/renesas,drif.txt > +++ /dev/null > @@ -1,177 +0,0 @@ > -Renesas R-Car Gen3 Digital Radio Interface controller (DRIF) > ------------------------------------------------------------- > - > -R-Car Gen3 DRIF is a SPI like receive only slave device. A general > -representation of DRIF interfacing with a master device is shown below. > - > -+---------------------+ +---------------------+ > -| |-----SCK------->|CLK | > -| Master |-----SS-------->|SYNC DRIFn (slave) | > -| |-----SD0------->|D0 | > -| |-----SD1------->|D1 | > -+---------------------+ +---------------------+ > - > -As per datasheet, each DRIF channel (drifn) is made up of two internal > -channels (drifn0 & drifn1). These two internal channels share the common > -CLK & SYNC. Each internal channel has its own dedicated resources like > -irq, dma channels, address space & clock. This internal split is not > -visible to the external master device. > - > -The device tree model represents each internal channel as a separate node. > -The internal channels sharing the CLK & SYNC are tied together by their > -phandles using a property called "renesas,bonding". For the rest of > -the documentation, unless explicitly stated, the word channel implies an > -internal channel. > - > -When both internal channels are enabled they need to be managed together > -as one (i.e.) they cannot operate alone as independent devices. Out of the > -two, one of them needs to act as a primary device that accepts common > -properties of both the internal channels. This channel is identified by a > -property called "renesas,primary-bond". > - > -To summarize, > - - When both the internal channels that are bonded together are enabled, > - the zeroth channel is selected as primary-bond. This channels accepts > - properties common to all the members of the bond. > - - When only one of the bonded channels need to be enabled, the property > - "renesas,bonding" or "renesas,primary-bond" will have no effect. That > - enabled channel can act alone as any other independent device. > - > -Required properties of an internal channel: > -------------------------------------------- > -- compatible: "renesas,r8a7795-drif" if DRIF controller is a part of R8A7795 SoC. > - "renesas,r8a7796-drif" if DRIF controller is a part of R8A7796 SoC. > - "renesas,rcar-gen3-drif" for a generic R-Car Gen3 compatible device. > - > - When compatible with the generic version, nodes must list the > - SoC-specific version corresponding to the platform first > - followed by the generic version. > - > -- reg: offset and length of that channel. > -- interrupts: associated with that channel. > -- clocks: phandle and clock specifier of that channel. > -- clock-names: clock input name string: "fck". > -- dmas: phandles to the DMA channels. > -- dma-names: names of the DMA channel: "rx". > -- renesas,bonding: phandle to the other channel. > - > -Optional properties of an internal channel: > -------------------------------------------- > -- power-domains: phandle to the respective power domain. > - > -Required properties of an internal channel when: > - - It is the only enabled channel of the bond (or) > - - If it acts as primary among enabled bonds > --------------------------------------------------------- > -- pinctrl-0: pin control group to be used for this channel. > -- pinctrl-names: must be "default". > -- renesas,primary-bond: empty property indicating the channel acts as primary > - among the bonded channels. > -- port: child port node corresponding to the data input, in accordance with > - the video interface bindings defined in > - Documentation/devicetree/bindings/media/video-interfaces.txt. The port > - node must contain at least one endpoint. > - > -Optional endpoint property: > ---------------------------- > -- sync-active: Indicates sync signal polarity, 0/1 for low/high respectively. > - This property maps to SYNCAC bit in the hardware manual. The > - default is 1 (active high). > - > -Example: > --------- > - > -(1) Both internal channels enabled: > ------------------------------------ > - > -When interfacing with a third party tuner device with two data pins as shown > -below. > - > -+---------------------+ +---------------------+ > -| |-----SCK------->|CLK | > -| Master |-----SS-------->|SYNC DRIFn (slave) | > -| |-----SD0------->|D0 | > -| |-----SD1------->|D1 | > -+---------------------+ +---------------------+ > - > - drif00: rif@e6f40000 { > - compatible = "renesas,r8a7795-drif", > - "renesas,rcar-gen3-drif"; > - reg = <0 0xe6f40000 0 0x64>; > - interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; > - clocks = <&cpg CPG_MOD 515>; > - clock-names = "fck"; > - dmas = <&dmac1 0x20>, <&dmac2 0x20>; > - dma-names = "rx", "rx"; > - power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; > - renesas,bonding = <&drif01>; > - renesas,primary-bond; > - pinctrl-0 = <&drif0_pins>; > - pinctrl-names = "default"; > - port { > - drif0_ep: endpoint { > - remote-endpoint = <&tuner_ep>; > - }; > - }; > - }; > - > - drif01: rif@e6f50000 { > - compatible = "renesas,r8a7795-drif", > - "renesas,rcar-gen3-drif"; > - reg = <0 0xe6f50000 0 0x64>; > - interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; > - clocks = <&cpg CPG_MOD 514>; > - clock-names = "fck"; > - dmas = <&dmac1 0x22>, <&dmac2 0x22>; > - dma-names = "rx", "rx"; > - power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; > - renesas,bonding = <&drif00>; > - }; > - > - > -(2) Internal channel 1 alone is enabled: > ----------------------------------------- > - > -When interfacing with a third party tuner device with one data pin as shown > -below. > - > -+---------------------+ +---------------------+ > -| |-----SCK------->|CLK | > -| Master |-----SS-------->|SYNC DRIFn (slave) | > -| | |D0 (unused) | > -| |-----SD-------->|D1 | > -+---------------------+ +---------------------+ > - > - drif00: rif@e6f40000 { > - compatible = "renesas,r8a7795-drif", > - "renesas,rcar-gen3-drif"; > - reg = <0 0xe6f40000 0 0x64>; > - interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; > - clocks = <&cpg CPG_MOD 515>; > - clock-names = "fck"; > - dmas = <&dmac1 0x20>, <&dmac2 0x20>; > - dma-names = "rx", "rx"; > - power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; > - renesas,bonding = <&drif01>; > - }; > - > - drif01: rif@e6f50000 { > - compatible = "renesas,r8a7795-drif", > - "renesas,rcar-gen3-drif"; > - reg = <0 0xe6f50000 0 0x64>; > - interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; > - clocks = <&cpg CPG_MOD 514>; > - clock-names = "fck"; > - dmas = <&dmac1 0x22>, <&dmac2 0x22>; > - dma-names = "rx", "rx"; > - power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; > - renesas,bonding = <&drif00>; > - pinctrl-0 = <&drif0_pins>; > - pinctrl-names = "default"; > - port { > - drif0_ep: endpoint { > - remote-endpoint = <&tuner_ep>; > - sync-active = <0>; > - }; > - }; > - }; > diff --git a/Documentation/devicetree/bindings/media/renesas,drif.yaml b/Documentation/devicetree/bindings/media/renesas,drif.yaml > new file mode 100644 > index 000000000000..f57fccc159d6 > --- /dev/null > +++ b/Documentation/devicetree/bindings/media/renesas,drif.yaml > @@ -0,0 +1,270 @@ > +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/media/renesas,drif.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Renesas R-Car Gen3 Digital Radio Interface controller (DRIF) > + > +maintainers: > + - Ramesh Shanmugasundaram <rashanmu@gmail.com> > + - Fabrizio Castro <fabrizio.castro.jz@renesas.com> > + > +description: | > + R-Car Gen3 DRIF is a SPI like receive only slave device. A general > + representation of DRIF interfacing with a master device is shown below. > + > + +---------------------+ +---------------------+ > + | |-----SCK------->|CLK | > + | Master |-----SS-------->|SYNC DRIFn (slave) | > + | |-----SD0------->|D0 | > + | |-----SD1------->|D1 | > + +---------------------+ +---------------------+ > + > + As per datasheet, each DRIF channel (drifn) is made up of two internal > + channels (drifn0 & drifn1). These two internal channels share the common > + CLK & SYNC. Each internal channel has its own dedicated resources like > + irq, dma channels, address space & clock. This internal split is not > + visible to the external master device. > + > + The device tree model represents each internal channel as a separate node. > + The internal channels sharing the CLK & SYNC are tied together by their > + phandles using a property called "renesas,bonding". For the rest of > + the documentation, unless explicitly stated, the word channel implies an > + internal channel. > + > + When both internal channels are enabled they need to be managed together > + as one (i.e.) they cannot operate alone as independent devices. Out of the > + two, one of them needs to act as a primary device that accepts common > + properties of both the internal channels. This channel is identified by a > + property called "renesas,primary-bond". > + > + To summarize, > + * When both the internal channels that are bonded together are enabled, > + the zeroth channel is selected as primary-bond. This channels accepts > + properties common to all the members of the bond. > + * When only one of the bonded channels need to be enabled, the property > + "renesas,bonding" or "renesas,primary-bond" will have no effect. That > + enabled channel can act alone as any other independent device. > + > +properties: > + compatible: > + items: > + - enum: > + - renesas,r8a7795-drif # R-Car H3 > + - renesas,r8a7796-drif # R-Car M3-W > + - const: renesas,rcar-gen3-drif # Generic R-Car Gen3 compatible device > + > + reg: > + maxItems: 1 > + > + interrupts: > + maxItems: 1 > + > + clocks: > + maxItems: 1 > + > + clock-names: > + maxItems: 1 > + items: > + - const: fck > + > + resets: > + maxItems: 1 > + > + dmas: > + minItems: 1 > + maxItems: 2 > + > + dma-names: > + minItems: 1 > + maxItems: 2 > + items: > + - const: rx > + - const: rx > + > + renesas,bonding: > + $ref: /schemas/types.yaml#/definitions/phandle > + description: > + The phandle to the other internal channel of DRIF > + > + power-domains: > + maxItems: 1 > + > + pinctrl-0: > + maxItems: 1 > + > + pinctrl-names: > + maxItems: 1 > + items: > + - const: default > + > + renesas,primary-bond: > + type: boolean > + description: > + Indicates that the channel acts as primary among the bonded channels. > + > + port: > + type: object > + description: > + Child port node corresponding to the data input, in accordance with the > + video interface bindings defined in > + Documentation/devicetree/bindings/media/video-interfaces.txt. > + The port node must contain at least one endpoint. > + > + properties: > + endpoint: > + type: object > + > + properties: > + remote-endpoint: > + description: > + A phandle to the remote tuner endpoint subnode in remote node > + port. > + > + sync-active: > + enum: [0, 1] > + description: > + Indicates sync signal polarity, 0/1 for low/high respectively. > + This property maps to SYNCAC bit in the hardware manual. The > + default is 1 (active high). > + > + additionalProperties: false > + > +required: > + - compatible > + - reg > + - interrupts > + - clocks > + - clock-names > + - resets > + - dmas > + - dma-names > + - renesas,bonding > + > +if: > + required: > + - renesas,primary-bond > +then: > + required: > + - pinctrl-0 > + - pinctrl-names > + - port > + > +additionalProperties: false > + > +examples: > + # Example with both internal channels enabled. > + # > + # When interfacing with a third party tuner device with two data pins as shown > + # below. > + # > + # +---------------------+ +---------------------+ > + # | |-----SCK------->|CLK | > + # | Master |-----SS-------->|SYNC DRIFn (slave) | > + # | |-----SD0------->|D0 | > + # | |-----SD1------->|D1 | > + # +---------------------+ +---------------------+ > + - | > + #include <dt-bindings/clock/r8a7795-cpg-mssr.h> > + #include <dt-bindings/interrupt-controller/arm-gic.h> > + #include <dt-bindings/power/r8a7795-sysc.h> > + > + soc { > + #address-cells = <2>; > + #size-cells = <2>; > + > + drif00: rif@e6f40000 { > + compatible = "renesas,r8a7795-drif", > + "renesas,rcar-gen3-drif"; > + reg = <0 0xe6f40000 0 0x64>; > + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&cpg CPG_MOD 515>; > + clock-names = "fck"; > + dmas = <&dmac1 0x20>, <&dmac2 0x20>; > + dma-names = "rx", "rx"; > + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; > + renesas,bonding = <&drif01>; > + resets = <&cpg 515>; > + renesas,primary-bond; > + pinctrl-0 = <&drif0_pins>; > + pinctrl-names = "default"; > + port { > + drif0_ep: endpoint { > + remote-endpoint = <&tuner_ep>; > + }; > + }; > + }; > + > + drif01: rif@e6f50000 { > + compatible = "renesas,r8a7795-drif", > + "renesas,rcar-gen3-drif"; > + reg = <0 0xe6f50000 0 0x64>; > + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&cpg CPG_MOD 514>; > + clock-names = "fck"; > + dmas = <&dmac1 0x22>, <&dmac2 0x22>; > + dma-names = "rx", "rx"; > + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; > + renesas,bonding = <&drif00>; > + resets = <&cpg 514>; > + }; > + }; > + > + # Example with internal channel 1 alone enabled. > + # > + # When interfacing with a third party tuner device with one data pin as shown > + # below. > + # > + # +---------------------+ +---------------------+ > + # | |-----SCK------->|CLK | > + # | Master |-----SS-------->|SYNC DRIFn (slave) | > + # | | |D0 (unused) | > + # | |-----SD-------->|D1 | > + # +---------------------+ +---------------------+ > + - | > + #include <dt-bindings/clock/r8a7795-cpg-mssr.h> > + #include <dt-bindings/interrupt-controller/arm-gic.h> > + #include <dt-bindings/power/r8a7795-sysc.h> > + > + soc { > + #address-cells = <2>; > + #size-cells = <2>; > + > + drif10: rif@e6f60000 { > + compatible = "renesas,r8a7795-drif", > + "renesas,rcar-gen3-drif"; > + reg = <0 0xe6f60000 0 0x64>; > + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&cpg CPG_MOD 513>; > + clock-names = "fck"; > + dmas = <&dmac1 0x24>, <&dmac2 0x24>; > + dma-names = "rx", "rx"; > + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; > + resets = <&cpg 513>; > + renesas,bonding = <&drif11>; > + }; > + > + drif11: rif@e6f70000 { > + compatible = "renesas,r8a7795-drif", > + "renesas,rcar-gen3-drif"; > + reg = <0 0xe6f70000 0 0x64>; > + interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&cpg CPG_MOD 512>; > + clock-names = "fck"; > + dmas = <&dmac1 0x26>, <&dmac2 0x26>; > + dma-names = "rx", "rx"; > + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; > + resets = <&cpg 512>; > + renesas,bonding = <&drif10>; > + pinctrl-0 = <&drif1_pins>; > + pinctrl-names = "default"; > + port { > + drif1_ep: endpoint { > + remote-endpoint = <&tuner_ep1>; > + sync-active = <0>; > + }; > + }; > + }; > + }; > +... > diff --git a/MAINTAINERS b/MAINTAINERS > index 9f49e5ac90d8..3e2a1cad3749 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -10903,7 +10903,7 @@ L: linux-media@vger.kernel.org > L: linux-renesas-soc@vger.kernel.org > S: Supported > T: git git://linuxtv.org/media_tree.git > -F: Documentation/devicetree/bindings/media/renesas,drif.txt > +F: Documentation/devicetree/bindings/media/renesas,drif.yaml > F: drivers/media/platform/rcar_drif.c > > MEDIA DRIVERS FOR RENESAS - FCP > -- > 2.25.1 > ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 2/3] media: dt-bindings: media: renesas,drif: Convert to json-schema 2020-09-15 13:12 ` [PATCH 2/3] media: dt-bindings: media: renesas,drif: Convert to json-schema Fabrizio Castro 2020-09-15 14:12 ` Lad, Prabhakar @ 2020-09-15 17:36 ` Laurent Pinchart 2020-09-15 17:44 ` Laurent Pinchart 1 sibling, 1 reply; 12+ messages in thread From: Laurent Pinchart @ 2020-09-15 17:36 UTC (permalink / raw) To: Fabrizio Castro Cc: Mauro Carvalho Chehab, Rob Herring, Geert Uytterhoeven, Ramesh Shanmugasundaram, linux-media, devicetree, linux-kernel, linux-renesas-soc, Chris Paterson, Biju Das, Prabhakar Mahadev Lad Hi Fabrizio, Thank you for the patch. On Tue, Sep 15, 2020 at 02:12:15PM +0100, Fabrizio Castro wrote: > Convert the Renesas DRIF bindings to DT schema and update > MAINTAINERS accordingly. > > Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com> > --- > .../bindings/media/renesas,drif.txt | 177 ------------ > .../bindings/media/renesas,drif.yaml | 270 ++++++++++++++++++ > MAINTAINERS | 2 +- > 3 files changed, 271 insertions(+), 178 deletions(-) > delete mode 100644 Documentation/devicetree/bindings/media/renesas,drif.txt > create mode 100644 Documentation/devicetree/bindings/media/renesas,drif.yaml > > diff --git a/Documentation/devicetree/bindings/media/renesas,drif.txt b/Documentation/devicetree/bindings/media/renesas,drif.txt > deleted file mode 100644 > index 0d8974aa8b38..000000000000 > --- a/Documentation/devicetree/bindings/media/renesas,drif.txt > +++ /dev/null > @@ -1,177 +0,0 @@ > -Renesas R-Car Gen3 Digital Radio Interface controller (DRIF) > ------------------------------------------------------------- > - > -R-Car Gen3 DRIF is a SPI like receive only slave device. A general > -representation of DRIF interfacing with a master device is shown below. > - > -+---------------------+ +---------------------+ > -| |-----SCK------->|CLK | > -| Master |-----SS-------->|SYNC DRIFn (slave) | > -| |-----SD0------->|D0 | > -| |-----SD1------->|D1 | > -+---------------------+ +---------------------+ > - > -As per datasheet, each DRIF channel (drifn) is made up of two internal > -channels (drifn0 & drifn1). These two internal channels share the common > -CLK & SYNC. Each internal channel has its own dedicated resources like > -irq, dma channels, address space & clock. This internal split is not > -visible to the external master device. > - > -The device tree model represents each internal channel as a separate node. > -The internal channels sharing the CLK & SYNC are tied together by their > -phandles using a property called "renesas,bonding". For the rest of > -the documentation, unless explicitly stated, the word channel implies an > -internal channel. > - > -When both internal channels are enabled they need to be managed together > -as one (i.e.) they cannot operate alone as independent devices. Out of the > -two, one of them needs to act as a primary device that accepts common > -properties of both the internal channels. This channel is identified by a > -property called "renesas,primary-bond". > - > -To summarize, > - - When both the internal channels that are bonded together are enabled, > - the zeroth channel is selected as primary-bond. This channels accepts > - properties common to all the members of the bond. > - - When only one of the bonded channels need to be enabled, the property > - "renesas,bonding" or "renesas,primary-bond" will have no effect. That > - enabled channel can act alone as any other independent device. > - > -Required properties of an internal channel: > -------------------------------------------- > -- compatible: "renesas,r8a7795-drif" if DRIF controller is a part of R8A7795 SoC. > - "renesas,r8a7796-drif" if DRIF controller is a part of R8A7796 SoC. > - "renesas,rcar-gen3-drif" for a generic R-Car Gen3 compatible device. > - > - When compatible with the generic version, nodes must list the > - SoC-specific version corresponding to the platform first > - followed by the generic version. > - > -- reg: offset and length of that channel. > -- interrupts: associated with that channel. > -- clocks: phandle and clock specifier of that channel. > -- clock-names: clock input name string: "fck". > -- dmas: phandles to the DMA channels. > -- dma-names: names of the DMA channel: "rx". > -- renesas,bonding: phandle to the other channel. > - > -Optional properties of an internal channel: > -------------------------------------------- > -- power-domains: phandle to the respective power domain. > - > -Required properties of an internal channel when: > - - It is the only enabled channel of the bond (or) > - - If it acts as primary among enabled bonds > --------------------------------------------------------- > -- pinctrl-0: pin control group to be used for this channel. > -- pinctrl-names: must be "default". > -- renesas,primary-bond: empty property indicating the channel acts as primary > - among the bonded channels. > -- port: child port node corresponding to the data input, in accordance with > - the video interface bindings defined in > - Documentation/devicetree/bindings/media/video-interfaces.txt. The port > - node must contain at least one endpoint. > - > -Optional endpoint property: > ---------------------------- > -- sync-active: Indicates sync signal polarity, 0/1 for low/high respectively. > - This property maps to SYNCAC bit in the hardware manual. The > - default is 1 (active high). > - > -Example: > --------- > - > -(1) Both internal channels enabled: > ------------------------------------ > - > -When interfacing with a third party tuner device with two data pins as shown > -below. > - > -+---------------------+ +---------------------+ > -| |-----SCK------->|CLK | > -| Master |-----SS-------->|SYNC DRIFn (slave) | > -| |-----SD0------->|D0 | > -| |-----SD1------->|D1 | > -+---------------------+ +---------------------+ > - > - drif00: rif@e6f40000 { > - compatible = "renesas,r8a7795-drif", > - "renesas,rcar-gen3-drif"; > - reg = <0 0xe6f40000 0 0x64>; > - interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; > - clocks = <&cpg CPG_MOD 515>; > - clock-names = "fck"; > - dmas = <&dmac1 0x20>, <&dmac2 0x20>; > - dma-names = "rx", "rx"; > - power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; > - renesas,bonding = <&drif01>; > - renesas,primary-bond; > - pinctrl-0 = <&drif0_pins>; > - pinctrl-names = "default"; > - port { > - drif0_ep: endpoint { > - remote-endpoint = <&tuner_ep>; > - }; > - }; > - }; > - > - drif01: rif@e6f50000 { > - compatible = "renesas,r8a7795-drif", > - "renesas,rcar-gen3-drif"; > - reg = <0 0xe6f50000 0 0x64>; > - interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; > - clocks = <&cpg CPG_MOD 514>; > - clock-names = "fck"; > - dmas = <&dmac1 0x22>, <&dmac2 0x22>; > - dma-names = "rx", "rx"; > - power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; > - renesas,bonding = <&drif00>; > - }; > - > - > -(2) Internal channel 1 alone is enabled: > ----------------------------------------- > - > -When interfacing with a third party tuner device with one data pin as shown > -below. > - > -+---------------------+ +---------------------+ > -| |-----SCK------->|CLK | > -| Master |-----SS-------->|SYNC DRIFn (slave) | > -| | |D0 (unused) | > -| |-----SD-------->|D1 | > -+---------------------+ +---------------------+ > - > - drif00: rif@e6f40000 { > - compatible = "renesas,r8a7795-drif", > - "renesas,rcar-gen3-drif"; > - reg = <0 0xe6f40000 0 0x64>; > - interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; > - clocks = <&cpg CPG_MOD 515>; > - clock-names = "fck"; > - dmas = <&dmac1 0x20>, <&dmac2 0x20>; > - dma-names = "rx", "rx"; > - power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; > - renesas,bonding = <&drif01>; > - }; > - > - drif01: rif@e6f50000 { > - compatible = "renesas,r8a7795-drif", > - "renesas,rcar-gen3-drif"; > - reg = <0 0xe6f50000 0 0x64>; > - interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; > - clocks = <&cpg CPG_MOD 514>; > - clock-names = "fck"; > - dmas = <&dmac1 0x22>, <&dmac2 0x22>; > - dma-names = "rx", "rx"; > - power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; > - renesas,bonding = <&drif00>; > - pinctrl-0 = <&drif0_pins>; > - pinctrl-names = "default"; > - port { > - drif0_ep: endpoint { > - remote-endpoint = <&tuner_ep>; > - sync-active = <0>; > - }; > - }; > - }; > diff --git a/Documentation/devicetree/bindings/media/renesas,drif.yaml b/Documentation/devicetree/bindings/media/renesas,drif.yaml > new file mode 100644 > index 000000000000..f57fccc159d6 > --- /dev/null > +++ b/Documentation/devicetree/bindings/media/renesas,drif.yaml > @@ -0,0 +1,270 @@ > +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/media/renesas,drif.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Renesas R-Car Gen3 Digital Radio Interface controller (DRIF) s/controller/Controller/ > + > +maintainers: > + - Ramesh Shanmugasundaram <rashanmu@gmail.com> > + - Fabrizio Castro <fabrizio.castro.jz@renesas.com> > + > +description: | > + R-Car Gen3 DRIF is a SPI like receive only slave device. A general > + representation of DRIF interfacing with a master device is shown below. > + > + +---------------------+ +---------------------+ > + | |-----SCK------->|CLK | > + | Master |-----SS-------->|SYNC DRIFn (slave) | > + | |-----SD0------->|D0 | > + | |-----SD1------->|D1 | > + +---------------------+ +---------------------+ > + > + As per datasheet, each DRIF channel (drifn) is made up of two internal > + channels (drifn0 & drifn1). These two internal channels share the common > + CLK & SYNC. Each internal channel has its own dedicated resources like > + irq, dma channels, address space & clock. This internal split is not > + visible to the external master device. > + > + The device tree model represents each internal channel as a separate node. > + The internal channels sharing the CLK & SYNC are tied together by their > + phandles using a property called "renesas,bonding". For the rest of > + the documentation, unless explicitly stated, the word channel implies an > + internal channel. > + > + When both internal channels are enabled they need to be managed together > + as one (i.e.) they cannot operate alone as independent devices. Out of the > + two, one of them needs to act as a primary device that accepts common > + properties of both the internal channels. This channel is identified by a > + property called "renesas,primary-bond". > + > + To summarize, > + * When both the internal channels that are bonded together are enabled, > + the zeroth channel is selected as primary-bond. This channels accepts > + properties common to all the members of the bond. > + * When only one of the bonded channels need to be enabled, the property > + "renesas,bonding" or "renesas,primary-bond" will have no effect. That > + enabled channel can act alone as any other independent device. > + > +properties: > + compatible: > + items: > + - enum: > + - renesas,r8a7795-drif # R-Car H3 > + - renesas,r8a7796-drif # R-Car M3-W > + - const: renesas,rcar-gen3-drif # Generic R-Car Gen3 compatible device > + > + reg: > + maxItems: 1 > + > + interrupts: > + maxItems: 1 > + > + clocks: > + maxItems: 1 > + > + clock-names: > + maxItems: 1 > + items: > + - const: fck > + > + resets: > + maxItems: 1 > + > + dmas: > + minItems: 1 > + maxItems: 2 > + > + dma-names: > + minItems: 1 > + maxItems: 2 > + items: > + - const: rx > + - const: rx > + > + renesas,bonding: > + $ref: /schemas/types.yaml#/definitions/phandle > + description: > + The phandle to the other internal channel of DRIF > + > + power-domains: > + maxItems: 1 > + > + pinctrl-0: > + maxItems: 1 > + > + pinctrl-names: > + maxItems: 1 > + items: > + - const: default You can drop those three properties, they're already handled by dt-schema. Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> > + > + renesas,primary-bond: > + type: boolean > + description: > + Indicates that the channel acts as primary among the bonded channels. > + > + port: > + type: object > + description: > + Child port node corresponding to the data input, in accordance with the > + video interface bindings defined in > + Documentation/devicetree/bindings/media/video-interfaces.txt. > + The port node must contain at least one endpoint. > + > + properties: > + endpoint: > + type: object > + > + properties: > + remote-endpoint: > + description: > + A phandle to the remote tuner endpoint subnode in remote node > + port. > + > + sync-active: > + enum: [0, 1] > + description: > + Indicates sync signal polarity, 0/1 for low/high respectively. > + This property maps to SYNCAC bit in the hardware manual. The > + default is 1 (active high). > + > + additionalProperties: false > + > +required: > + - compatible > + - reg > + - interrupts > + - clocks > + - clock-names > + - resets > + - dmas > + - dma-names > + - renesas,bonding > + > +if: > + required: > + - renesas,primary-bond > +then: > + required: > + - pinctrl-0 > + - pinctrl-names > + - port > + > +additionalProperties: false > + > +examples: > + # Example with both internal channels enabled. > + # > + # When interfacing with a third party tuner device with two data pins as shown > + # below. > + # > + # +---------------------+ +---------------------+ > + # | |-----SCK------->|CLK | > + # | Master |-----SS-------->|SYNC DRIFn (slave) | > + # | |-----SD0------->|D0 | > + # | |-----SD1------->|D1 | > + # +---------------------+ +---------------------+ > + - | > + #include <dt-bindings/clock/r8a7795-cpg-mssr.h> > + #include <dt-bindings/interrupt-controller/arm-gic.h> > + #include <dt-bindings/power/r8a7795-sysc.h> > + > + soc { > + #address-cells = <2>; > + #size-cells = <2>; > + > + drif00: rif@e6f40000 { > + compatible = "renesas,r8a7795-drif", > + "renesas,rcar-gen3-drif"; > + reg = <0 0xe6f40000 0 0x64>; > + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&cpg CPG_MOD 515>; > + clock-names = "fck"; > + dmas = <&dmac1 0x20>, <&dmac2 0x20>; > + dma-names = "rx", "rx"; > + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; > + renesas,bonding = <&drif01>; > + resets = <&cpg 515>; > + renesas,primary-bond; > + pinctrl-0 = <&drif0_pins>; > + pinctrl-names = "default"; > + port { > + drif0_ep: endpoint { > + remote-endpoint = <&tuner_ep>; > + }; > + }; > + }; > + > + drif01: rif@e6f50000 { > + compatible = "renesas,r8a7795-drif", > + "renesas,rcar-gen3-drif"; > + reg = <0 0xe6f50000 0 0x64>; > + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&cpg CPG_MOD 514>; > + clock-names = "fck"; > + dmas = <&dmac1 0x22>, <&dmac2 0x22>; > + dma-names = "rx", "rx"; > + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; > + renesas,bonding = <&drif00>; > + resets = <&cpg 514>; > + }; > + }; > + > + # Example with internal channel 1 alone enabled. > + # > + # When interfacing with a third party tuner device with one data pin as shown > + # below. > + # > + # +---------------------+ +---------------------+ > + # | |-----SCK------->|CLK | > + # | Master |-----SS-------->|SYNC DRIFn (slave) | > + # | | |D0 (unused) | > + # | |-----SD-------->|D1 | > + # +---------------------+ +---------------------+ > + - | > + #include <dt-bindings/clock/r8a7795-cpg-mssr.h> > + #include <dt-bindings/interrupt-controller/arm-gic.h> > + #include <dt-bindings/power/r8a7795-sysc.h> > + > + soc { > + #address-cells = <2>; > + #size-cells = <2>; > + > + drif10: rif@e6f60000 { > + compatible = "renesas,r8a7795-drif", > + "renesas,rcar-gen3-drif"; > + reg = <0 0xe6f60000 0 0x64>; > + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&cpg CPG_MOD 513>; > + clock-names = "fck"; > + dmas = <&dmac1 0x24>, <&dmac2 0x24>; > + dma-names = "rx", "rx"; > + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; > + resets = <&cpg 513>; > + renesas,bonding = <&drif11>; > + }; > + > + drif11: rif@e6f70000 { > + compatible = "renesas,r8a7795-drif", > + "renesas,rcar-gen3-drif"; > + reg = <0 0xe6f70000 0 0x64>; > + interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&cpg CPG_MOD 512>; > + clock-names = "fck"; > + dmas = <&dmac1 0x26>, <&dmac2 0x26>; > + dma-names = "rx", "rx"; > + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; > + resets = <&cpg 512>; > + renesas,bonding = <&drif10>; > + pinctrl-0 = <&drif1_pins>; > + pinctrl-names = "default"; > + port { > + drif1_ep: endpoint { > + remote-endpoint = <&tuner_ep1>; > + sync-active = <0>; > + }; > + }; > + }; > + }; > +... > diff --git a/MAINTAINERS b/MAINTAINERS > index 9f49e5ac90d8..3e2a1cad3749 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -10903,7 +10903,7 @@ L: linux-media@vger.kernel.org > L: linux-renesas-soc@vger.kernel.org > S: Supported > T: git git://linuxtv.org/media_tree.git > -F: Documentation/devicetree/bindings/media/renesas,drif.txt > +F: Documentation/devicetree/bindings/media/renesas,drif.yaml > F: drivers/media/platform/rcar_drif.c > > MEDIA DRIVERS FOR RENESAS - FCP -- Regards, Laurent Pinchart ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 2/3] media: dt-bindings: media: renesas,drif: Convert to json-schema 2020-09-15 17:36 ` Laurent Pinchart @ 2020-09-15 17:44 ` Laurent Pinchart 2020-09-16 10:42 ` Fabrizio Castro 0 siblings, 1 reply; 12+ messages in thread From: Laurent Pinchart @ 2020-09-15 17:44 UTC (permalink / raw) To: Fabrizio Castro Cc: Mauro Carvalho Chehab, Rob Herring, Geert Uytterhoeven, Ramesh Shanmugasundaram, linux-media, devicetree, linux-kernel, linux-renesas-soc, Chris Paterson, Biju Das, Prabhakar Mahadev Lad On Tue, Sep 15, 2020 at 08:36:39PM +0300, Laurent Pinchart wrote: > Hi Fabrizio, > > Thank you for the patch. > > On Tue, Sep 15, 2020 at 02:12:15PM +0100, Fabrizio Castro wrote: > > Convert the Renesas DRIF bindings to DT schema and update > > MAINTAINERS accordingly. > > > > Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com> > > --- > > .../bindings/media/renesas,drif.txt | 177 ------------ > > .../bindings/media/renesas,drif.yaml | 270 ++++++++++++++++++ > > MAINTAINERS | 2 +- > > 3 files changed, 271 insertions(+), 178 deletions(-) > > delete mode 100644 Documentation/devicetree/bindings/media/renesas,drif.txt > > create mode 100644 Documentation/devicetree/bindings/media/renesas,drif.yaml > > > > diff --git a/Documentation/devicetree/bindings/media/renesas,drif.txt b/Documentation/devicetree/bindings/media/renesas,drif.txt > > deleted file mode 100644 > > index 0d8974aa8b38..000000000000 > > --- a/Documentation/devicetree/bindings/media/renesas,drif.txt > > +++ /dev/null > > @@ -1,177 +0,0 @@ > > -Renesas R-Car Gen3 Digital Radio Interface controller (DRIF) > > ------------------------------------------------------------- > > - > > -R-Car Gen3 DRIF is a SPI like receive only slave device. A general > > -representation of DRIF interfacing with a master device is shown below. > > - > > -+---------------------+ +---------------------+ > > -| |-----SCK------->|CLK | > > -| Master |-----SS-------->|SYNC DRIFn (slave) | > > -| |-----SD0------->|D0 | > > -| |-----SD1------->|D1 | > > -+---------------------+ +---------------------+ > > - > > -As per datasheet, each DRIF channel (drifn) is made up of two internal > > -channels (drifn0 & drifn1). These two internal channels share the common > > -CLK & SYNC. Each internal channel has its own dedicated resources like > > -irq, dma channels, address space & clock. This internal split is not > > -visible to the external master device. > > - > > -The device tree model represents each internal channel as a separate node. > > -The internal channels sharing the CLK & SYNC are tied together by their > > -phandles using a property called "renesas,bonding". For the rest of > > -the documentation, unless explicitly stated, the word channel implies an > > -internal channel. > > - > > -When both internal channels are enabled they need to be managed together > > -as one (i.e.) they cannot operate alone as independent devices. Out of the > > -two, one of them needs to act as a primary device that accepts common > > -properties of both the internal channels. This channel is identified by a > > -property called "renesas,primary-bond". > > - > > -To summarize, > > - - When both the internal channels that are bonded together are enabled, > > - the zeroth channel is selected as primary-bond. This channels accepts > > - properties common to all the members of the bond. > > - - When only one of the bonded channels need to be enabled, the property > > - "renesas,bonding" or "renesas,primary-bond" will have no effect. That > > - enabled channel can act alone as any other independent device. > > - > > -Required properties of an internal channel: > > -------------------------------------------- > > -- compatible: "renesas,r8a7795-drif" if DRIF controller is a part of R8A7795 SoC. > > - "renesas,r8a7796-drif" if DRIF controller is a part of R8A7796 SoC. > > - "renesas,rcar-gen3-drif" for a generic R-Car Gen3 compatible device. > > - > > - When compatible with the generic version, nodes must list the > > - SoC-specific version corresponding to the platform first > > - followed by the generic version. > > - > > -- reg: offset and length of that channel. > > -- interrupts: associated with that channel. > > -- clocks: phandle and clock specifier of that channel. > > -- clock-names: clock input name string: "fck". > > -- dmas: phandles to the DMA channels. > > -- dma-names: names of the DMA channel: "rx". > > -- renesas,bonding: phandle to the other channel. > > - > > -Optional properties of an internal channel: > > -------------------------------------------- > > -- power-domains: phandle to the respective power domain. > > - > > -Required properties of an internal channel when: > > - - It is the only enabled channel of the bond (or) > > - - If it acts as primary among enabled bonds > > --------------------------------------------------------- > > -- pinctrl-0: pin control group to be used for this channel. > > -- pinctrl-names: must be "default". > > -- renesas,primary-bond: empty property indicating the channel acts as primary > > - among the bonded channels. > > -- port: child port node corresponding to the data input, in accordance with > > - the video interface bindings defined in > > - Documentation/devicetree/bindings/media/video-interfaces.txt. The port > > - node must contain at least one endpoint. > > - > > -Optional endpoint property: > > ---------------------------- > > -- sync-active: Indicates sync signal polarity, 0/1 for low/high respectively. > > - This property maps to SYNCAC bit in the hardware manual. The > > - default is 1 (active high). > > - > > -Example: > > --------- > > - > > -(1) Both internal channels enabled: > > ------------------------------------ > > - > > -When interfacing with a third party tuner device with two data pins as shown > > -below. > > - > > -+---------------------+ +---------------------+ > > -| |-----SCK------->|CLK | > > -| Master |-----SS-------->|SYNC DRIFn (slave) | > > -| |-----SD0------->|D0 | > > -| |-----SD1------->|D1 | > > -+---------------------+ +---------------------+ > > - > > - drif00: rif@e6f40000 { > > - compatible = "renesas,r8a7795-drif", > > - "renesas,rcar-gen3-drif"; > > - reg = <0 0xe6f40000 0 0x64>; > > - interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; > > - clocks = <&cpg CPG_MOD 515>; > > - clock-names = "fck"; > > - dmas = <&dmac1 0x20>, <&dmac2 0x20>; > > - dma-names = "rx", "rx"; > > - power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; > > - renesas,bonding = <&drif01>; > > - renesas,primary-bond; > > - pinctrl-0 = <&drif0_pins>; > > - pinctrl-names = "default"; > > - port { > > - drif0_ep: endpoint { > > - remote-endpoint = <&tuner_ep>; > > - }; > > - }; > > - }; > > - > > - drif01: rif@e6f50000 { > > - compatible = "renesas,r8a7795-drif", > > - "renesas,rcar-gen3-drif"; > > - reg = <0 0xe6f50000 0 0x64>; > > - interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; > > - clocks = <&cpg CPG_MOD 514>; > > - clock-names = "fck"; > > - dmas = <&dmac1 0x22>, <&dmac2 0x22>; > > - dma-names = "rx", "rx"; > > - power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; > > - renesas,bonding = <&drif00>; > > - }; > > - > > - > > -(2) Internal channel 1 alone is enabled: > > ----------------------------------------- > > - > > -When interfacing with a third party tuner device with one data pin as shown > > -below. > > - > > -+---------------------+ +---------------------+ > > -| |-----SCK------->|CLK | > > -| Master |-----SS-------->|SYNC DRIFn (slave) | > > -| | |D0 (unused) | > > -| |-----SD-------->|D1 | > > -+---------------------+ +---------------------+ > > - > > - drif00: rif@e6f40000 { > > - compatible = "renesas,r8a7795-drif", > > - "renesas,rcar-gen3-drif"; > > - reg = <0 0xe6f40000 0 0x64>; > > - interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; > > - clocks = <&cpg CPG_MOD 515>; > > - clock-names = "fck"; > > - dmas = <&dmac1 0x20>, <&dmac2 0x20>; > > - dma-names = "rx", "rx"; > > - power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; > > - renesas,bonding = <&drif01>; > > - }; > > - > > - drif01: rif@e6f50000 { > > - compatible = "renesas,r8a7795-drif", > > - "renesas,rcar-gen3-drif"; > > - reg = <0 0xe6f50000 0 0x64>; > > - interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; > > - clocks = <&cpg CPG_MOD 514>; > > - clock-names = "fck"; > > - dmas = <&dmac1 0x22>, <&dmac2 0x22>; > > - dma-names = "rx", "rx"; > > - power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; > > - renesas,bonding = <&drif00>; > > - pinctrl-0 = <&drif0_pins>; > > - pinctrl-names = "default"; > > - port { > > - drif0_ep: endpoint { > > - remote-endpoint = <&tuner_ep>; > > - sync-active = <0>; > > - }; > > - }; > > - }; > > diff --git a/Documentation/devicetree/bindings/media/renesas,drif.yaml b/Documentation/devicetree/bindings/media/renesas,drif.yaml > > new file mode 100644 > > index 000000000000..f57fccc159d6 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/media/renesas,drif.yaml > > @@ -0,0 +1,270 @@ > > +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause > > +%YAML 1.2 > > +--- > > +$id: http://devicetree.org/schemas/media/renesas,drif.yaml# > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > + > > +title: Renesas R-Car Gen3 Digital Radio Interface controller (DRIF) > > s/controller/Controller/ > > > + > > +maintainers: > > + - Ramesh Shanmugasundaram <rashanmu@gmail.com> > > + - Fabrizio Castro <fabrizio.castro.jz@renesas.com> > > + > > +description: | > > + R-Car Gen3 DRIF is a SPI like receive only slave device. A general > > + representation of DRIF interfacing with a master device is shown below. > > + > > + +---------------------+ +---------------------+ > > + | |-----SCK------->|CLK | > > + | Master |-----SS-------->|SYNC DRIFn (slave) | > > + | |-----SD0------->|D0 | > > + | |-----SD1------->|D1 | > > + +---------------------+ +---------------------+ > > + > > + As per datasheet, each DRIF channel (drifn) is made up of two internal > > + channels (drifn0 & drifn1). These two internal channels share the common > > + CLK & SYNC. Each internal channel has its own dedicated resources like > > + irq, dma channels, address space & clock. This internal split is not > > + visible to the external master device. > > + > > + The device tree model represents each internal channel as a separate node. > > + The internal channels sharing the CLK & SYNC are tied together by their > > + phandles using a property called "renesas,bonding". For the rest of > > + the documentation, unless explicitly stated, the word channel implies an > > + internal channel. > > + > > + When both internal channels are enabled they need to be managed together > > + as one (i.e.) they cannot operate alone as independent devices. Out of the > > + two, one of them needs to act as a primary device that accepts common > > + properties of both the internal channels. This channel is identified by a > > + property called "renesas,primary-bond". > > + > > + To summarize, > > + * When both the internal channels that are bonded together are enabled, > > + the zeroth channel is selected as primary-bond. This channels accepts > > + properties common to all the members of the bond. > > + * When only one of the bonded channels need to be enabled, the property > > + "renesas,bonding" or "renesas,primary-bond" will have no effect. That > > + enabled channel can act alone as any other independent device. > > + > > +properties: > > + compatible: > > + items: > > + - enum: > > + - renesas,r8a7795-drif # R-Car H3 > > + - renesas,r8a7796-drif # R-Car M3-W > > + - const: renesas,rcar-gen3-drif # Generic R-Car Gen3 compatible device > > + > > + reg: > > + maxItems: 1 > > + > > + interrupts: > > + maxItems: 1 > > + > > + clocks: > > + maxItems: 1 > > + > > + clock-names: > > + maxItems: 1 > > + items: > > + - const: fck > > + > > + resets: > > + maxItems: 1 > > + > > + dmas: > > + minItems: 1 > > + maxItems: 2 > > + > > + dma-names: > > + minItems: 1 > > + maxItems: 2 > > + items: > > + - const: rx > > + - const: rx > > + > > + renesas,bonding: > > + $ref: /schemas/types.yaml#/definitions/phandle > > + description: > > + The phandle to the other internal channel of DRIF > > + > > + power-domains: > > + maxItems: 1 > > + > > + pinctrl-0: > > + maxItems: 1 > > + > > + pinctrl-names: > > + maxItems: 1 > > + items: > > + - const: default > > You can drop those three properties, they're already handled by > dt-schema. It looks like I'm wrong, power-domains seems to be required. I'm not sure why though, as the power-domain-consumer.yaml schema has select: true. Maybe Rob can comment on this, in the meantime let's keep the power-domains property. > Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> > > > + > > + renesas,primary-bond: > > + type: boolean > > + description: > > + Indicates that the channel acts as primary among the bonded channels. > > + > > + port: > > + type: object > > + description: > > + Child port node corresponding to the data input, in accordance with the > > + video interface bindings defined in > > + Documentation/devicetree/bindings/media/video-interfaces.txt. > > + The port node must contain at least one endpoint. > > + > > + properties: > > + endpoint: > > + type: object > > + > > + properties: > > + remote-endpoint: > > + description: > > + A phandle to the remote tuner endpoint subnode in remote node > > + port. > > + > > + sync-active: > > + enum: [0, 1] > > + description: > > + Indicates sync signal polarity, 0/1 for low/high respectively. > > + This property maps to SYNCAC bit in the hardware manual. The > > + default is 1 (active high). > > + > > + additionalProperties: false > > + > > +required: > > + - compatible > > + - reg > > + - interrupts > > + - clocks > > + - clock-names > > + - resets > > + - dmas > > + - dma-names > > + - renesas,bonding > > + > > +if: > > + required: > > + - renesas,primary-bond > > +then: > > + required: > > + - pinctrl-0 > > + - pinctrl-names > > + - port > > + > > +additionalProperties: false > > + > > +examples: > > + # Example with both internal channels enabled. > > + # > > + # When interfacing with a third party tuner device with two data pins as shown > > + # below. > > + # > > + # +---------------------+ +---------------------+ > > + # | |-----SCK------->|CLK | > > + # | Master |-----SS-------->|SYNC DRIFn (slave) | > > + # | |-----SD0------->|D0 | > > + # | |-----SD1------->|D1 | > > + # +---------------------+ +---------------------+ > > + - | > > + #include <dt-bindings/clock/r8a7795-cpg-mssr.h> > > + #include <dt-bindings/interrupt-controller/arm-gic.h> > > + #include <dt-bindings/power/r8a7795-sysc.h> > > + > > + soc { > > + #address-cells = <2>; > > + #size-cells = <2>; > > + > > + drif00: rif@e6f40000 { > > + compatible = "renesas,r8a7795-drif", > > + "renesas,rcar-gen3-drif"; > > + reg = <0 0xe6f40000 0 0x64>; > > + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&cpg CPG_MOD 515>; > > + clock-names = "fck"; > > + dmas = <&dmac1 0x20>, <&dmac2 0x20>; > > + dma-names = "rx", "rx"; > > + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; > > + renesas,bonding = <&drif01>; > > + resets = <&cpg 515>; > > + renesas,primary-bond; > > + pinctrl-0 = <&drif0_pins>; > > + pinctrl-names = "default"; > > + port { > > + drif0_ep: endpoint { > > + remote-endpoint = <&tuner_ep>; > > + }; > > + }; > > + }; > > + > > + drif01: rif@e6f50000 { > > + compatible = "renesas,r8a7795-drif", > > + "renesas,rcar-gen3-drif"; > > + reg = <0 0xe6f50000 0 0x64>; > > + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&cpg CPG_MOD 514>; > > + clock-names = "fck"; > > + dmas = <&dmac1 0x22>, <&dmac2 0x22>; > > + dma-names = "rx", "rx"; > > + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; > > + renesas,bonding = <&drif00>; > > + resets = <&cpg 514>; > > + }; > > + }; > > + > > + # Example with internal channel 1 alone enabled. > > + # > > + # When interfacing with a third party tuner device with one data pin as shown > > + # below. > > + # > > + # +---------------------+ +---------------------+ > > + # | |-----SCK------->|CLK | > > + # | Master |-----SS-------->|SYNC DRIFn (slave) | > > + # | | |D0 (unused) | > > + # | |-----SD-------->|D1 | > > + # +---------------------+ +---------------------+ > > + - | > > + #include <dt-bindings/clock/r8a7795-cpg-mssr.h> > > + #include <dt-bindings/interrupt-controller/arm-gic.h> > > + #include <dt-bindings/power/r8a7795-sysc.h> > > + > > + soc { > > + #address-cells = <2>; > > + #size-cells = <2>; > > + > > + drif10: rif@e6f60000 { > > + compatible = "renesas,r8a7795-drif", > > + "renesas,rcar-gen3-drif"; > > + reg = <0 0xe6f60000 0 0x64>; > > + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&cpg CPG_MOD 513>; > > + clock-names = "fck"; > > + dmas = <&dmac1 0x24>, <&dmac2 0x24>; > > + dma-names = "rx", "rx"; > > + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; > > + resets = <&cpg 513>; > > + renesas,bonding = <&drif11>; > > + }; > > + > > + drif11: rif@e6f70000 { > > + compatible = "renesas,r8a7795-drif", > > + "renesas,rcar-gen3-drif"; > > + reg = <0 0xe6f70000 0 0x64>; > > + interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&cpg CPG_MOD 512>; > > + clock-names = "fck"; > > + dmas = <&dmac1 0x26>, <&dmac2 0x26>; > > + dma-names = "rx", "rx"; > > + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; > > + resets = <&cpg 512>; > > + renesas,bonding = <&drif10>; > > + pinctrl-0 = <&drif1_pins>; > > + pinctrl-names = "default"; > > + port { > > + drif1_ep: endpoint { > > + remote-endpoint = <&tuner_ep1>; > > + sync-active = <0>; > > + }; > > + }; > > + }; > > + }; > > +... > > diff --git a/MAINTAINERS b/MAINTAINERS > > index 9f49e5ac90d8..3e2a1cad3749 100644 > > --- a/MAINTAINERS > > +++ b/MAINTAINERS > > @@ -10903,7 +10903,7 @@ L: linux-media@vger.kernel.org > > L: linux-renesas-soc@vger.kernel.org > > S: Supported > > T: git git://linuxtv.org/media_tree.git > > -F: Documentation/devicetree/bindings/media/renesas,drif.txt > > +F: Documentation/devicetree/bindings/media/renesas,drif.yaml > > F: drivers/media/platform/rcar_drif.c > > > > MEDIA DRIVERS FOR RENESAS - FCP -- Regards, Laurent Pinchart ^ permalink raw reply [flat|nested] 12+ messages in thread
* RE: [PATCH 2/3] media: dt-bindings: media: renesas,drif: Convert to json-schema 2020-09-15 17:44 ` Laurent Pinchart @ 2020-09-16 10:42 ` Fabrizio Castro 0 siblings, 0 replies; 12+ messages in thread From: Fabrizio Castro @ 2020-09-16 10:42 UTC (permalink / raw) To: Laurent Pinchart Cc: Mauro Carvalho Chehab, Rob Herring, Geert Uytterhoeven, Ramesh Shanmugasundaram, linux-media, devicetree, linux-kernel, linux-renesas-soc, Chris Paterson, Biju Das, Prabhakar Mahadev Lad Hi Laurent, Thank you for your feedback. > From: Laurent Pinchart <laurent.pinchart@ideasonboard.com> > Sent: 15 September 2020 18:45 > > On Tue, Sep 15, 2020 at 08:36:39PM +0300, Laurent Pinchart wrote: > > Hi Fabrizio, > > > > Thank you for the patch. > > > > On Tue, Sep 15, 2020 at 02:12:15PM +0100, Fabrizio Castro wrote: > > > Convert the Renesas DRIF bindings to DT schema and update > > > MAINTAINERS accordingly. > > > > > > Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com> > > > --- > > > .../bindings/media/renesas,drif.txt | 177 ------------ > > > .../bindings/media/renesas,drif.yaml | 270 ++++++++++++++++++ > > > MAINTAINERS | 2 +- > > > 3 files changed, 271 insertions(+), 178 deletions(-) > > > delete mode 100644 > Documentation/devicetree/bindings/media/renesas,drif.txt > > > create mode 100644 > Documentation/devicetree/bindings/media/renesas,drif.yaml > > > > > > diff --git a/Documentation/devicetree/bindings/media/renesas,drif.txt > b/Documentation/devicetree/bindings/media/renesas,drif.txt > > > deleted file mode 100644 > > > index 0d8974aa8b38..000000000000 > > > --- a/Documentation/devicetree/bindings/media/renesas,drif.txt > > > +++ /dev/null > > > @@ -1,177 +0,0 @@ > > > -Renesas R-Car Gen3 Digital Radio Interface controller (DRIF) > > > ------------------------------------------------------------- > > > - > > > -R-Car Gen3 DRIF is a SPI like receive only slave device. A general > > > -representation of DRIF interfacing with a master device is shown below. > > > - > > > -+---------------------+ +---------------------+ > > > -| |-----SCK------->|CLK | > > > -| Master |-----SS-------->|SYNC DRIFn (slave) | > > > -| |-----SD0------->|D0 | > > > -| |-----SD1------->|D1 | > > > -+---------------------+ +---------------------+ > > > - > > > -As per datasheet, each DRIF channel (drifn) is made up of two internal > > > -channels (drifn0 & drifn1). These two internal channels share the > common > > > -CLK & SYNC. Each internal channel has its own dedicated resources like > > > -irq, dma channels, address space & clock. This internal split is not > > > -visible to the external master device. > > > - > > > -The device tree model represents each internal channel as a separate > node. > > > -The internal channels sharing the CLK & SYNC are tied together by their > > > -phandles using a property called "renesas,bonding". For the rest of > > > -the documentation, unless explicitly stated, the word channel implies an > > > -internal channel. > > > - > > > -When both internal channels are enabled they need to be managed > together > > > -as one (i.e.) they cannot operate alone as independent devices. Out of > the > > > -two, one of them needs to act as a primary device that accepts common > > > -properties of both the internal channels. This channel is identified by a > > > -property called "renesas,primary-bond". > > > - > > > -To summarize, > > > - - When both the internal channels that are bonded together are > enabled, > > > - the zeroth channel is selected as primary-bond. This channels accepts > > > - properties common to all the members of the bond. > > > - - When only one of the bonded channels need to be enabled, the > property > > > - "renesas,bonding" or "renesas,primary-bond" will have no effect. > That > > > - enabled channel can act alone as any other independent device. > > > - > > > -Required properties of an internal channel: > > > -------------------------------------------- > > > -- compatible:"renesas,r8a7795-drif" if DRIF controller is a part of > R8A7795 SoC. > > > -"renesas,r8a7796-drif" if DRIF controller is a part of R8A7796 > SoC. > > > -"renesas,rcar-gen3-drif" for a generic R-Car Gen3 compatible > device. > > > - > > > -When compatible with the generic version, nodes must list > the > > > -SoC-specific version corresponding to the platform first > > > -followed by the generic version. > > > - > > > -- reg: offset and length of that channel. > > > -- interrupts: associated with that channel. > > > -- clocks: phandle and clock specifier of that channel. > > > -- clock-names: clock input name string: "fck". > > > -- dmas: phandles to the DMA channels. > > > -- dma-names: names of the DMA channel: "rx". > > > -- renesas,bonding: phandle to the other channel. > > > - > > > -Optional properties of an internal channel: > > > -------------------------------------------- > > > -- power-domains: phandle to the respective power domain. > > > - > > > -Required properties of an internal channel when: > > > -- It is the only enabled channel of the bond (or) > > > -- If it acts as primary among enabled bonds > > > --------------------------------------------------------- > > > -- pinctrl-0: pin control group to be used for this channel. > > > -- pinctrl-names: must be "default". > > > -- renesas,primary-bond: empty property indicating the channel acts as > primary > > > -among the bonded channels. > > > -- port: child port node corresponding to the data input, in accordance > with > > > -the video interface bindings defined in > > > -Documentation/devicetree/bindings/media/video-interfaces.txt. > The port > > > -node must contain at least one endpoint. > > > - > > > -Optional endpoint property: > > > ---------------------------- > > > -- sync-active: Indicates sync signal polarity, 0/1 for low/high respectively. > > > - This property maps to SYNCAC bit in the hardware manual. The > > > - default is 1 (active high). > > > - > > > -Example: > > > --------- > > > - > > > -(1) Both internal channels enabled: > > > ------------------------------------ > > > - > > > -When interfacing with a third party tuner device with two data pins as > shown > > > -below. > > > - > > > -+---------------------+ +---------------------+ > > > -| |-----SCK------->|CLK | > > > -| Master |-----SS-------->|SYNC DRIFn (slave) | > > > -| |-----SD0------->|D0 | > > > -| |-----SD1------->|D1 | > > > -+---------------------+ +---------------------+ > > > - > > > -drif00: rif@e6f40000 { > > > -compatible = "renesas,r8a7795-drif", > > > - "renesas,rcar-gen3-drif"; > > > -reg = <0 0xe6f40000 0 0x64>; > > > -interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; > > > -clocks = <&cpg CPG_MOD 515>; > > > -clock-names = "fck"; > > > -dmas = <&dmac1 0x20>, <&dmac2 0x20>; > > > -dma-names = "rx", "rx"; > > > -power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; > > > -renesas,bonding = <&drif01>; > > > -renesas,primary-bond; > > > -pinctrl-0 = <&drif0_pins>; > > > -pinctrl-names = "default"; > > > -port { > > > -drif0_ep: endpoint { > > > - remote-endpoint = <&tuner_ep>; > > > -}; > > > -}; > > > -}; > > > - > > > -drif01: rif@e6f50000 { > > > -compatible = "renesas,r8a7795-drif", > > > - "renesas,rcar-gen3-drif"; > > > -reg = <0 0xe6f50000 0 0x64>; > > > -interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; > > > -clocks = <&cpg CPG_MOD 514>; > > > -clock-names = "fck"; > > > -dmas = <&dmac1 0x22>, <&dmac2 0x22>; > > > -dma-names = "rx", "rx"; > > > -power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; > > > -renesas,bonding = <&drif00>; > > > -}; > > > - > > > - > > > -(2) Internal channel 1 alone is enabled: > > > ----------------------------------------- > > > - > > > -When interfacing with a third party tuner device with one data pin as > shown > > > -below. > > > - > > > -+---------------------+ +---------------------+ > > > -| |-----SCK------->|CLK | > > > -| Master |-----SS-------->|SYNC DRIFn (slave) | > > > -| | |D0 (unused) | > > > -| |-----SD-------->|D1 | > > > -+---------------------+ +---------------------+ > > > - > > > -drif00: rif@e6f40000 { > > > -compatible = "renesas,r8a7795-drif", > > > - "renesas,rcar-gen3-drif"; > > > -reg = <0 0xe6f40000 0 0x64>; > > > -interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; > > > -clocks = <&cpg CPG_MOD 515>; > > > -clock-names = "fck"; > > > -dmas = <&dmac1 0x20>, <&dmac2 0x20>; > > > -dma-names = "rx", "rx"; > > > -power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; > > > -renesas,bonding = <&drif01>; > > > -}; > > > - > > > -drif01: rif@e6f50000 { > > > -compatible = "renesas,r8a7795-drif", > > > - "renesas,rcar-gen3-drif"; > > > -reg = <0 0xe6f50000 0 0x64>; > > > -interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; > > > -clocks = <&cpg CPG_MOD 514>; > > > -clock-names = "fck"; > > > -dmas = <&dmac1 0x22>, <&dmac2 0x22>; > > > -dma-names = "rx", "rx"; > > > -power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; > > > -renesas,bonding = <&drif00>; > > > -pinctrl-0 = <&drif0_pins>; > > > -pinctrl-names = "default"; > > > -port { > > > -drif0_ep: endpoint { > > > - remote-endpoint = <&tuner_ep>; > > > - sync-active = <0>; > > > -}; > > > -}; > > > -}; > > > diff --git a/Documentation/devicetree/bindings/media/renesas,drif.yaml > b/Documentation/devicetree/bindings/media/renesas,drif.yaml > > > new file mode 100644 > > > index 000000000000..f57fccc159d6 > > > --- /dev/null > > > +++ b/Documentation/devicetree/bindings/media/renesas,drif.yaml > > > @@ -0,0 +1,270 @@ > > > +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause > > > +%YAML 1.2 > > > +--- > > > +$id: http://devicetree.org/schemas/media/renesas,drif.yaml# > > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > > + > > > +title: Renesas R-Car Gen3 Digital Radio Interface controller (DRIF) > > > > s/controller/Controller/ Will fix with V2 > > > > > + > > > +maintainers: > > > + - Ramesh Shanmugasundaram <rashanmu@gmail.com> > > > + - Fabrizio Castro <fabrizio.castro.jz@renesas.com> > > > + > > > +description: | > > > + R-Car Gen3 DRIF is a SPI like receive only slave device. A general > > > + representation of DRIF interfacing with a master device is shown > below. > > > + > > > + +---------------------+ +---------------------+ > > > + | |-----SCK------->|CLK | > > > + | Master |-----SS-------->|SYNC DRIFn (slave) | > > > + | |-----SD0------->|D0 | > > > + | |-----SD1------->|D1 | > > > + +---------------------+ +---------------------+ > > > + > > > + As per datasheet, each DRIF channel (drifn) is made up of two internal > > > + channels (drifn0 & drifn1). These two internal channels share the > common > > > + CLK & SYNC. Each internal channel has its own dedicated resources like > > > + irq, dma channels, address space & clock. This internal split is not > > > + visible to the external master device. > > > + > > > + The device tree model represents each internal channel as a separate > node. > > > + The internal channels sharing the CLK & SYNC are tied together by their > > > + phandles using a property called "renesas,bonding". For the rest of > > > + the documentation, unless explicitly stated, the word channel implies > an > > > + internal channel. > > > + > > > + When both internal channels are enabled they need to be managed > together > > > + as one (i.e.) they cannot operate alone as independent devices. Out of > the > > > + two, one of them needs to act as a primary device that accepts > common > > > + properties of both the internal channels. This channel is identified by a > > > + property called "renesas,primary-bond". > > > + > > > + To summarize, > > > + * When both the internal channels that are bonded together are > enabled, > > > + the zeroth channel is selected as primary-bond. This channels > accepts > > > + properties common to all the members of the bond. > > > + * When only one of the bonded channels need to be enabled, the > property > > > + "renesas,bonding" or "renesas,primary-bond" will have no effect. > That > > > + enabled channel can act alone as any other independent device. > > > + > > > +properties: > > > + compatible: > > > + items: > > > + - enum: > > > + - renesas,r8a7795-drif # R-Car H3 > > > + - renesas,r8a7796-drif # R-Car M3-W > > > + - const: renesas,rcar-gen3-drif # Generic R-Car Gen3 compatible > device > > > + > > > + reg: > > > + maxItems: 1 > > > + > > > + interrupts: > > > + maxItems: 1 > > > + > > > + clocks: > > > + maxItems: 1 > > > + > > > + clock-names: > > > + maxItems: 1 > > > + items: > > > + - const: fck > > > + > > > + resets: > > > + maxItems: 1 > > > + > > > + dmas: > > > + minItems: 1 > > > + maxItems: 2 > > > + > > > + dma-names: > > > + minItems: 1 > > > + maxItems: 2 > > > + items: > > > + - const: rx > > > + - const: rx > > > + > > > + renesas,bonding: > > > + $ref: /schemas/types.yaml#/definitions/phandle > > > + description: > > > + The phandle to the other internal channel of DRIF > > > + > > > + power-domains: > > > + maxItems: 1 > > > + > > > + pinctrl-0: > > > + maxItems: 1 > > > + > > > + pinctrl-names: > > > + maxItems: 1 > > > + items: > > > + - const: default > > > > You can drop those three properties, they're already handled by > > dt-schema. > > It looks like I'm wrong, power-domains seems to be required. I'm not > sure why though, as the power-domain-consumer.yaml schema has select: > true. Maybe Rob can comment on this, in the meantime let's keep the > power-domains property. Ok, will leave it for v2, and wait for Rob's reply. Thanks, Fab > > > Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> > > > > > + > > > + renesas,primary-bond: > > > + type: boolean > > > + description: > > > + Indicates that the channel acts as primary among the bonded > channels. > > > + > > > + port: > > > + type: object > > > + description: > > > + Child port node corresponding to the data input, in accordance with > the > > > + video interface bindings defined in > > > + Documentation/devicetree/bindings/media/video-interfaces.txt. > > > + The port node must contain at least one endpoint. > > > + > > > + properties: > > > + endpoint: > > > + type: object > > > + > > > + properties: > > > + remote-endpoint: > > > + description: > > > + A phandle to the remote tuner endpoint subnode in remote > node > > > + port. > > > + > > > + sync-active: > > > + enum: [0, 1] > > > + description: > > > + Indicates sync signal polarity, 0/1 for low/high respectively. > > > + This property maps to SYNCAC bit in the hardware manual. The > > > + default is 1 (active high). > > > + > > > + additionalProperties: false > > > + > > > +required: > > > + - compatible > > > + - reg > > > + - interrupts > > > + - clocks > > > + - clock-names > > > + - resets > > > + - dmas > > > + - dma-names > > > + - renesas,bonding > > > + > > > +if: > > > + required: > > > + - renesas,primary-bond > > > +then: > > > + required: > > > + - pinctrl-0 > > > + - pinctrl-names > > > + - port > > > + > > > +additionalProperties: false > > > + > > > +examples: > > > + # Example with both internal channels enabled. > > > + # > > > + # When interfacing with a third party tuner device with two data pins as > shown > > > + # below. > > > + # > > > + # +---------------------+ +---------------------+ > > > + # | |-----SCK------->|CLK | > > > + # | Master |-----SS-------->|SYNC DRIFn (slave) | > > > + # | |-----SD0------->|D0 | > > > + # | |-----SD1------->|D1 | > > > + # +---------------------+ +---------------------+ > > > + - | > > > + #include <dt-bindings/clock/r8a7795-cpg-mssr.h> > > > + #include <dt-bindings/interrupt-controller/arm-gic.h> > > > + #include <dt-bindings/power/r8a7795-sysc.h> > > > + > > > + soc { > > > + #address-cells = <2>; > > > + #size-cells = <2>; > > > + > > > + drif00: rif@e6f40000 { > > > + compatible = "renesas,r8a7795-drif", > > > + "renesas,rcar-gen3-drif"; > > > + reg = <0 0xe6f40000 0 0x64>; > > > + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; > > > + clocks = <&cpg CPG_MOD 515>; > > > + clock-names = "fck"; > > > + dmas = <&dmac1 0x20>, <&dmac2 0x20>; > > > + dma-names = "rx", "rx"; > > > + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; > > > + renesas,bonding = <&drif01>; > > > + resets = <&cpg 515>; > > > + renesas,primary-bond; > > > + pinctrl-0 = <&drif0_pins>; > > > + pinctrl-names = "default"; > > > + port { > > > + drif0_ep: endpoint { > > > + remote-endpoint = <&tuner_ep>; > > > + }; > > > + }; > > > + }; > > > + > > > + drif01: rif@e6f50000 { > > > + compatible = "renesas,r8a7795-drif", > > > + "renesas,rcar-gen3-drif"; > > > + reg = <0 0xe6f50000 0 0x64>; > > > + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; > > > + clocks = <&cpg CPG_MOD 514>; > > > + clock-names = "fck"; > > > + dmas = <&dmac1 0x22>, <&dmac2 0x22>; > > > + dma-names = "rx", "rx"; > > > + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; > > > + renesas,bonding = <&drif00>; > > > + resets = <&cpg 514>; > > > + }; > > > + }; > > > + > > > + # Example with internal channel 1 alone enabled. > > > + # > > > + # When interfacing with a third party tuner device with one data pin as > shown > > > + # below. > > > + # > > > + # +---------------------+ +---------------------+ > > > + # | |-----SCK------->|CLK | > > > + # | Master |-----SS-------->|SYNC DRIFn (slave) | > > > + # | | |D0 (unused) | > > > + # | |-----SD-------->|D1 | > > > + # +---------------------+ +---------------------+ > > > + - | > > > + #include <dt-bindings/clock/r8a7795-cpg-mssr.h> > > > + #include <dt-bindings/interrupt-controller/arm-gic.h> > > > + #include <dt-bindings/power/r8a7795-sysc.h> > > > + > > > + soc { > > > + #address-cells = <2>; > > > + #size-cells = <2>; > > > + > > > + drif10: rif@e6f60000 { > > > + compatible = "renesas,r8a7795-drif", > > > + "renesas,rcar-gen3-drif"; > > > + reg = <0 0xe6f60000 0 0x64>; > > > + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; > > > + clocks = <&cpg CPG_MOD 513>; > > > + clock-names = "fck"; > > > + dmas = <&dmac1 0x24>, <&dmac2 0x24>; > > > + dma-names = "rx", "rx"; > > > + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; > > > + resets = <&cpg 513>; > > > + renesas,bonding = <&drif11>; > > > + }; > > > + > > > + drif11: rif@e6f70000 { > > > + compatible = "renesas,r8a7795-drif", > > > + "renesas,rcar-gen3-drif"; > > > + reg = <0 0xe6f70000 0 0x64>; > > > + interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; > > > + clocks = <&cpg CPG_MOD 512>; > > > + clock-names = "fck"; > > > + dmas = <&dmac1 0x26>, <&dmac2 0x26>; > > > + dma-names = "rx", "rx"; > > > + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; > > > + resets = <&cpg 512>; > > > + renesas,bonding = <&drif10>; > > > + pinctrl-0 = <&drif1_pins>; > > > + pinctrl-names = "default"; > > > + port { > > > + drif1_ep: endpoint { > > > + remote-endpoint = <&tuner_ep1>; > > > + sync-active = <0>; > > > + }; > > > + }; > > > + }; > > > + }; > > > +... > > > diff --git a/MAINTAINERS b/MAINTAINERS > > > index 9f49e5ac90d8..3e2a1cad3749 100644 > > > --- a/MAINTAINERS > > > +++ b/MAINTAINERS > > > @@ -10903,7 +10903,7 @@ L:linux-media@vger.kernel.org > > > L:linux-renesas-soc@vger.kernel.org > > > S:Supported > > > T:git git://linuxtv.org/media_tree.git > > > -F:Documentation/devicetree/bindings/media/renesas,drif.txt > > > +F:Documentation/devicetree/bindings/media/renesas,drif.yaml > > > F:drivers/media/platform/rcar_drif.c > > > > > > MEDIA DRIVERS FOR RENESAS - FCP > > -- > Regards, > > Laurent Pinchart Renesas Electronics Europe GmbH, Geschaeftsfuehrer/President: Carsten Jauch, Sitz der Gesellschaft/Registered office: Duesseldorf, Arcadiastrasse 10, 40472 Duesseldorf, Germany, Handelsregister/Commercial Register: Duesseldorf, HRB 3708 USt-IDNr./Tax identification no.: DE 119353406 WEEE-Reg.-Nr./WEEE reg. no.: DE 14978647 ^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH 3/3] media: dt-bindings: media: renesas,drif: Add r8a77990 support 2020-09-15 13:12 [PATCH 0/3] Document r8a77990 DRIF support Fabrizio Castro 2020-09-15 13:12 ` [PATCH 1/3] MAINTAINERS: Add Fabrizio Castro to Renesas DRIF Fabrizio Castro 2020-09-15 13:12 ` [PATCH 2/3] media: dt-bindings: media: renesas,drif: Convert to json-schema Fabrizio Castro @ 2020-09-15 13:12 ` Fabrizio Castro 2020-09-15 13:31 ` Geert Uytterhoeven ` (2 more replies) 2 siblings, 3 replies; 12+ messages in thread From: Fabrizio Castro @ 2020-09-15 13:12 UTC (permalink / raw) To: Mauro Carvalho Chehab, Rob Herring, Geert Uytterhoeven Cc: Fabrizio Castro, Ramesh Shanmugasundaram, linux-media, devicetree, linux-kernel, linux-renesas-soc, Chris Paterson, Biju Das, Prabhakar Mahadev Lad, Laurent Pinchart The r8a77990 (a.k.a. R-Car E3) device tree schema is compatible with R-Car H3 and M3-W schema. Document r8a77990 support within renesas,drif.yaml. Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com> --- Documentation/devicetree/bindings/media/renesas,drif.yaml | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/media/renesas,drif.yaml b/Documentation/devicetree/bindings/media/renesas,drif.yaml index f57fccc159d6..051d515be38d 100644 --- a/Documentation/devicetree/bindings/media/renesas,drif.yaml +++ b/Documentation/devicetree/bindings/media/renesas,drif.yaml @@ -53,6 +53,7 @@ properties: - enum: - renesas,r8a7795-drif # R-Car H3 - renesas,r8a7796-drif # R-Car M3-W + - renesas,r8a77990-drif # R-Car E3 - const: renesas,rcar-gen3-drif # Generic R-Car Gen3 compatible device reg: -- 2.25.1 ^ permalink raw reply related [flat|nested] 12+ messages in thread
* Re: [PATCH 3/3] media: dt-bindings: media: renesas,drif: Add r8a77990 support 2020-09-15 13:12 ` [PATCH 3/3] media: dt-bindings: media: renesas,drif: Add r8a77990 support Fabrizio Castro @ 2020-09-15 13:31 ` Geert Uytterhoeven 2020-09-15 14:13 ` Lad, Prabhakar 2020-09-15 17:37 ` Laurent Pinchart 2 siblings, 0 replies; 12+ messages in thread From: Geert Uytterhoeven @ 2020-09-15 13:31 UTC (permalink / raw) To: Fabrizio Castro Cc: Mauro Carvalho Chehab, Rob Herring, Ramesh Shanmugasundaram, Linux Media Mailing List, open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS, Linux Kernel Mailing List, Linux-Renesas, Chris Paterson, Biju Das, Prabhakar Mahadev Lad, Laurent Pinchart On Tue, Sep 15, 2020 at 3:12 PM Fabrizio Castro <fabrizio.castro.jz@renesas.com> wrote: > The r8a77990 (a.k.a. R-Car E3) device tree schema is > compatible with R-Car H3 and M3-W schema. > > Document r8a77990 support within renesas,drif.yaml. > > Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Gr{oetje,eeting}s, Geert -- Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that. -- Linus Torvalds ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 3/3] media: dt-bindings: media: renesas,drif: Add r8a77990 support 2020-09-15 13:12 ` [PATCH 3/3] media: dt-bindings: media: renesas,drif: Add r8a77990 support Fabrizio Castro 2020-09-15 13:31 ` Geert Uytterhoeven @ 2020-09-15 14:13 ` Lad, Prabhakar 2020-09-15 17:37 ` Laurent Pinchart 2 siblings, 0 replies; 12+ messages in thread From: Lad, Prabhakar @ 2020-09-15 14:13 UTC (permalink / raw) To: Fabrizio Castro Cc: Mauro Carvalho Chehab, Rob Herring, Geert Uytterhoeven, Ramesh Shanmugasundaram, linux-media, open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS, LKML, Linux-Renesas, Chris Paterson, Biju Das, Prabhakar Mahadev Lad, Laurent Pinchart Hi Fabrizio, Thank you for the patch. On Tue, Sep 15, 2020 at 2:19 PM Fabrizio Castro <fabrizio.castro.jz@renesas.com> wrote: > > The r8a77990 (a.k.a. R-Car E3) device tree schema is > compatible with R-Car H3 and M3-W schema. > > Document r8a77990 support within renesas,drif.yaml. > > Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com> > --- > Documentation/devicetree/bindings/media/renesas,drif.yaml | 1 + > 1 file changed, 1 insertion(+) > Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Cheers, Prabhakar > diff --git a/Documentation/devicetree/bindings/media/renesas,drif.yaml b/Documentation/devicetree/bindings/media/renesas,drif.yaml > index f57fccc159d6..051d515be38d 100644 > --- a/Documentation/devicetree/bindings/media/renesas,drif.yaml > +++ b/Documentation/devicetree/bindings/media/renesas,drif.yaml > @@ -53,6 +53,7 @@ properties: > - enum: > - renesas,r8a7795-drif # R-Car H3 > - renesas,r8a7796-drif # R-Car M3-W > + - renesas,r8a77990-drif # R-Car E3 > - const: renesas,rcar-gen3-drif # Generic R-Car Gen3 compatible device > > reg: > -- > 2.25.1 > ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 3/3] media: dt-bindings: media: renesas,drif: Add r8a77990 support 2020-09-15 13:12 ` [PATCH 3/3] media: dt-bindings: media: renesas,drif: Add r8a77990 support Fabrizio Castro 2020-09-15 13:31 ` Geert Uytterhoeven 2020-09-15 14:13 ` Lad, Prabhakar @ 2020-09-15 17:37 ` Laurent Pinchart 2 siblings, 0 replies; 12+ messages in thread From: Laurent Pinchart @ 2020-09-15 17:37 UTC (permalink / raw) To: Fabrizio Castro Cc: Mauro Carvalho Chehab, Rob Herring, Geert Uytterhoeven, Ramesh Shanmugasundaram, linux-media, devicetree, linux-kernel, linux-renesas-soc, Chris Paterson, Biju Das, Prabhakar Mahadev Lad Hi Fabrizio, Thank you for the patch. On Tue, Sep 15, 2020 at 02:12:16PM +0100, Fabrizio Castro wrote: > The r8a77990 (a.k.a. R-Car E3) device tree schema is > compatible with R-Car H3 and M3-W schema. > > Document r8a77990 support within renesas,drif.yaml. > > Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> > --- > Documentation/devicetree/bindings/media/renesas,drif.yaml | 1 + > 1 file changed, 1 insertion(+) > > diff --git a/Documentation/devicetree/bindings/media/renesas,drif.yaml b/Documentation/devicetree/bindings/media/renesas,drif.yaml > index f57fccc159d6..051d515be38d 100644 > --- a/Documentation/devicetree/bindings/media/renesas,drif.yaml > +++ b/Documentation/devicetree/bindings/media/renesas,drif.yaml > @@ -53,6 +53,7 @@ properties: > - enum: > - renesas,r8a7795-drif # R-Car H3 > - renesas,r8a7796-drif # R-Car M3-W > + - renesas,r8a77990-drif # R-Car E3 > - const: renesas,rcar-gen3-drif # Generic R-Car Gen3 compatible device > > reg: -- Regards, Laurent Pinchart ^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2020-09-16 18:55 UTC | newest] Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2020-09-15 13:12 [PATCH 0/3] Document r8a77990 DRIF support Fabrizio Castro 2020-09-15 13:12 ` [PATCH 1/3] MAINTAINERS: Add Fabrizio Castro to Renesas DRIF Fabrizio Castro 2020-09-15 16:11 ` Laurent Pinchart 2020-09-15 13:12 ` [PATCH 2/3] media: dt-bindings: media: renesas,drif: Convert to json-schema Fabrizio Castro 2020-09-15 14:12 ` Lad, Prabhakar 2020-09-15 17:36 ` Laurent Pinchart 2020-09-15 17:44 ` Laurent Pinchart 2020-09-16 10:42 ` Fabrizio Castro 2020-09-15 13:12 ` [PATCH 3/3] media: dt-bindings: media: renesas,drif: Add r8a77990 support Fabrizio Castro 2020-09-15 13:31 ` Geert Uytterhoeven 2020-09-15 14:13 ` Lad, Prabhakar 2020-09-15 17:37 ` Laurent Pinchart
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.