* Configuring and using RIPngd
@ 2013-08-14 10:02 Ale Lampro
2013-08-14 15:24 ` Phil Oester
0 siblings, 1 reply; 3+ messages in thread
From: Ale Lampro @ 2013-08-14 10:02 UTC (permalink / raw)
To: netdev
Hi,
I am new to the list and I am trying to achieve something that I think
should be relatively easy with RIPngd and Quagga, but I am new to all
this so I have some issues.
I have two computers connected by a Serial link. I use "tunslip" which
creates a slip connection between them and mounts a tap0 interface in
my ubuntu linux computer.
The other computer generates a Response RIPng message advertising
ADDR1 (ipv6 address) in a given moment, which arrives to the linux
computer by the tap0 interface.
What I would like to do is to run ripng in this computer so that it
adds ADDR1 to its routing table but I am not able to do it.
The configuration for zebra and ripngd are the following.
ripngd: http://pastebin.com/Y8GHkcDB (link to the conf file)
zebra: http://pastebin.com/ZEVRfLx0 (link to the conf file)
As I was not sure at all of how I should configure them I just reused
a few things that I found on the internet but I guess it may not be
enough.
I would really appreciate if someone could give me a hint with this.
Thanks a lot.
Best regards,
Alejandro
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: Configuring and using RIPngd
2013-08-14 10:02 Configuring and using RIPngd Ale Lampro
@ 2013-08-14 15:24 ` Phil Oester
2013-08-14 15:34 ` Ale Lampro
0 siblings, 1 reply; 3+ messages in thread
From: Phil Oester @ 2013-08-14 15:24 UTC (permalink / raw)
To: Ale Lampro; +Cc: netdev
On Wed, Aug 14, 2013 at 12:02:35PM +0200, Ale Lampro wrote:
> Hi,
>
> I am new to the list and I am trying to achieve something that I think
> should be relatively easy with RIPngd and Quagga, but I am new to all
> this so I have some issues.
Best to ask this question on the Quagga mailing list.
Phil
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: Configuring and using RIPngd
2013-08-14 15:24 ` Phil Oester
@ 2013-08-14 15:34 ` Ale Lampro
0 siblings, 0 replies; 3+ messages in thread
From: Ale Lampro @ 2013-08-14 15:34 UTC (permalink / raw)
To: Phil Oester; +Cc: netdev
Hi Phil,
Thanks, you are totally right.
On Wed, Aug 14, 2013 at 5:24 PM, Phil Oester <kernel@linuxace.com> wrote:
> On Wed, Aug 14, 2013 at 12:02:35PM +0200, Ale Lampro wrote:
>> Hi,
>>
>> I am new to the list and I am trying to achieve something that I think
>> should be relatively easy with RIPngd and Quagga, but I am new to all
>> this so I have some issues.
>
> Best to ask this question on the Quagga mailing list.
>
> Phil
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2013-08-14 15:34 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2013-08-14 10:02 Configuring and using RIPngd Ale Lampro
2013-08-14 15:24 ` Phil Oester
2013-08-14 15:34 ` Ale Lampro
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.