* [PATCH] pinctrl: samsung: modularize samsung pinctrl driver [not found] <CGME20191121072643epcas2p452071a503725c7764acf5084d24425b1@epcas2p4.samsung.com> @ 2019-11-21 7:26 ` 구현기 0 siblings, 0 replies; 12+ messages in thread From: 구현기 @ 2019-11-21 7:26 UTC (permalink / raw) To: tomasz.figa, krzk, s.nawrocki, linus.walleij Cc: linux-arm-kernel, linux-samsung-soc, linux-gpio, linux-kernel Enable samsung pinctrl driver to be compiled as modules. Change-Id: I92a9953c92831a316f7f50146898ff19831549ec Signed-off-by: Hyunki Koo <hyunki00.koo@samsung.com> --- drivers/pinctrl/samsung/Kconfig | 5 +---- drivers/pinctrl/samsung/Makefile | 13 +++++++------ drivers/pinctrl/samsung/pinctrl-exynos-arm.c | 2 ++ drivers/pinctrl/samsung/pinctrl-exynos-arm64.c | 2 ++ drivers/pinctrl/samsung/pinctrl-exynos.c | 2 ++ drivers/pinctrl/samsung/pinctrl-samsung.c | 13 +++++++++++++ 6 files changed, 27 insertions(+), 10 deletions(-) diff --git a/drivers/pinctrl/samsung/Kconfig b/drivers/pinctrl/samsung/Kconfig index 425fadd6c346..25e16984ef23 100644 --- a/drivers/pinctrl/samsung/Kconfig +++ b/drivers/pinctrl/samsung/Kconfig @@ -3,14 +3,13 @@ # Samsung Pin control drivers # config PINCTRL_SAMSUNG - bool + tristate "Pinctrl driver data for Samsung SoCs" select PINMUX select PINCONF config PINCTRL_EXYNOS bool "Pinctrl driver data for Samsung EXYNOS SoCs" depends on OF && GPIOLIB && (ARCH_EXYNOS || ARCH_S5PV210) - select PINCTRL_SAMSUNG select PINCTRL_EXYNOS_ARM if ARM && (ARCH_EXYNOS || ARCH_S5PV210) select PINCTRL_EXYNOS_ARM64 if ARM64 && ARCH_EXYNOS @@ -25,9 +24,7 @@ config PINCTRL_EXYNOS_ARM64 config PINCTRL_S3C24XX bool "Samsung S3C24XX SoC pinctrl driver" depends on ARCH_S3C24XX && OF - select PINCTRL_SAMSUNG config PINCTRL_S3C64XX bool "Samsung S3C64XX SoC pinctrl driver" depends on ARCH_S3C64XX - select PINCTRL_SAMSUNG diff --git a/drivers/pinctrl/samsung/Makefile b/drivers/pinctrl/samsung/Makefile index ed951df6a112..b3ac01838b8a 100644 --- a/drivers/pinctrl/samsung/Makefile +++ b/drivers/pinctrl/samsung/Makefile @@ -1,9 +1,10 @@ # SPDX-License-Identifier: GPL-2.0 # Samsung pin control drivers -obj-$(CONFIG_PINCTRL_SAMSUNG) += pinctrl-samsung.o -obj-$(CONFIG_PINCTRL_EXYNOS) += pinctrl-exynos.o -obj-$(CONFIG_PINCTRL_EXYNOS_ARM) += pinctrl-exynos-arm.o -obj-$(CONFIG_PINCTRL_EXYNOS_ARM64) += pinctrl-exynos-arm64.o -obj-$(CONFIG_PINCTRL_S3C24XX) += pinctrl-s3c24xx.o -obj-$(CONFIG_PINCTRL_S3C64XX) += pinctrl-s3c64xx.o +obj-$(CONFIG_PINCTRL_SAMSUNG) += pinctrl-samsung-super.o +pinctrl-samsung-super-$(CONFIG_PINCTRL_SAMSUNG) += pinctrl-samsung.o +pinctrl-samsung-super-$(CONFIG_PINCTRL_EXYNOS) += pinctrl-exynos.o +pinctrl-samsung-super-$(CONFIG_PINCTRL_EXYNOS_ARM) += pinctrl-exynos- arm.o +pinctrl-samsung-super-$(CONFIG_PINCTRL_EXYNOS_ARM64) += pinctrl-exynos- arm64.o +pinctrl-samsung-super-$(CONFIG_PINCTRL_S3C24XX) += pinctrl-s3c24xx.o +pinctrl-samsung-super-$(CONFIG_PINCTRL_S3C64XX) += pinctrl-s3c64xx.o diff --git a/drivers/pinctrl/samsung/pinctrl-exynos-arm.c b/drivers/pinctrl/samsung/pinctrl-exynos-arm.c index 85ddf49a5188..28906bf213c4 100644 --- a/drivers/pinctrl/samsung/pinctrl-exynos-arm.c +++ b/drivers/pinctrl/samsung/pinctrl-exynos-arm.c @@ -14,6 +14,7 @@ // external gpio and wakeup interrupt support. #include <linux/device.h> +#include <linux/module.h> #include <linux/of_address.h> #include <linux/slab.h> #include <linux/err.h> @@ -891,3 +892,4 @@ const struct samsung_pinctrl_of_match_data exynos5420_of_data __initconst = { .ctrl = exynos5420_pin_ctrl, .num_ctrl = ARRAY_SIZE(exynos5420_pin_ctrl), }; +MODULE_LICENSE("GPL"); diff --git a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c index b6e56422a700..2b19476ad5ff 100644 --- a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c +++ b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c @@ -14,6 +14,7 @@ // external gpio and wakeup interrupt support. #include <linux/slab.h> +#include <linux/module.h> #include <linux/soc/samsung/exynos-regs-pmu.h> #include "pinctrl-samsung.h" @@ -422,3 +423,4 @@ const struct samsung_pinctrl_of_match_data exynos7_of_data __initconst = { .ctrl = exynos7_pin_ctrl, .num_ctrl = ARRAY_SIZE(exynos7_pin_ctrl), }; +MODULE_LICENSE("GPL"); diff --git a/drivers/pinctrl/samsung/pinctrl-exynos.c b/drivers/pinctrl/samsung/pinctrl-exynos.c index ebc27b06718c..630d606330f1 100644 --- a/drivers/pinctrl/samsung/pinctrl-exynos.c +++ b/drivers/pinctrl/samsung/pinctrl-exynos.c @@ -18,6 +18,7 @@ #include <linux/irqdomain.h> #include <linux/irq.h> #include <linux/irqchip/chained_irq.h> +#include <linux/module.h> #include <linux/of.h> #include <linux/of_irq.h> #include <linux/slab.h> @@ -713,3 +714,4 @@ exynos_retention_init(struct samsung_pinctrl_drv_data *drvdata, return ctrl; } +MODULE_LICENSE("GPL"); diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.c b/drivers/pinctrl/samsung/pinctrl-samsung.c index de0477bb469d..4483eaed27f8 100644 --- a/drivers/pinctrl/samsung/pinctrl-samsung.c +++ b/drivers/pinctrl/samsung/pinctrl-samsung.c @@ -15,6 +15,7 @@ // but provides extensions to which platform specific implementation of the gpio // and wakeup interrupts can be hooked to. +#include <linux/module.h> #include <linux/init.h> #include <linux/platform_device.h> #include <linux/io.h> @@ -1275,6 +1276,7 @@ static const struct of_device_id samsung_pinctrl_dt_match[] = { #endif {}, }; +MODULE_DEVICE_TABLE(of, samsung_pinctrl_dt_match); static const struct dev_pm_ops samsung_pinctrl_pm_ops = { SET_LATE_SYSTEM_SLEEP_PM_OPS(samsung_pinctrl_suspend, @@ -1296,3 +1298,14 @@ static int __init samsung_pinctrl_drv_register(void) return platform_driver_register(&samsung_pinctrl_driver); } postcore_initcall(samsung_pinctrl_drv_register); + +static void __exit samsung_pinctrl_drv_unregister(void) +{ + platform_driver_unregister(&samsung_pinctrl_driver); +} +module_exit(samsung_pinctrl_drv_unregister); + + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Hyunki Koo <hyunki00.koo@samsung.com>"); +MODULE_DESCRIPTION("Samsung Exynos PINCTRL driver"); -- 2.15.0.rc1 ^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH] pinctrl: samsung: modularize samsung pinctrl driver @ 2019-11-21 7:26 ` 구현기 0 siblings, 0 replies; 12+ messages in thread From: 구현기 @ 2019-11-21 7:26 UTC (permalink / raw) To: tomasz.figa, krzk, s.nawrocki, linus.walleij Cc: linux-gpio, linux-samsung-soc, linux-kernel, linux-arm-kernel Enable samsung pinctrl driver to be compiled as modules. Change-Id: I92a9953c92831a316f7f50146898ff19831549ec Signed-off-by: Hyunki Koo <hyunki00.koo@samsung.com> --- drivers/pinctrl/samsung/Kconfig | 5 +---- drivers/pinctrl/samsung/Makefile | 13 +++++++------ drivers/pinctrl/samsung/pinctrl-exynos-arm.c | 2 ++ drivers/pinctrl/samsung/pinctrl-exynos-arm64.c | 2 ++ drivers/pinctrl/samsung/pinctrl-exynos.c | 2 ++ drivers/pinctrl/samsung/pinctrl-samsung.c | 13 +++++++++++++ 6 files changed, 27 insertions(+), 10 deletions(-) diff --git a/drivers/pinctrl/samsung/Kconfig b/drivers/pinctrl/samsung/Kconfig index 425fadd6c346..25e16984ef23 100644 --- a/drivers/pinctrl/samsung/Kconfig +++ b/drivers/pinctrl/samsung/Kconfig @@ -3,14 +3,13 @@ # Samsung Pin control drivers # config PINCTRL_SAMSUNG - bool + tristate "Pinctrl driver data for Samsung SoCs" select PINMUX select PINCONF config PINCTRL_EXYNOS bool "Pinctrl driver data for Samsung EXYNOS SoCs" depends on OF && GPIOLIB && (ARCH_EXYNOS || ARCH_S5PV210) - select PINCTRL_SAMSUNG select PINCTRL_EXYNOS_ARM if ARM && (ARCH_EXYNOS || ARCH_S5PV210) select PINCTRL_EXYNOS_ARM64 if ARM64 && ARCH_EXYNOS @@ -25,9 +24,7 @@ config PINCTRL_EXYNOS_ARM64 config PINCTRL_S3C24XX bool "Samsung S3C24XX SoC pinctrl driver" depends on ARCH_S3C24XX && OF - select PINCTRL_SAMSUNG config PINCTRL_S3C64XX bool "Samsung S3C64XX SoC pinctrl driver" depends on ARCH_S3C64XX - select PINCTRL_SAMSUNG diff --git a/drivers/pinctrl/samsung/Makefile b/drivers/pinctrl/samsung/Makefile index ed951df6a112..b3ac01838b8a 100644 --- a/drivers/pinctrl/samsung/Makefile +++ b/drivers/pinctrl/samsung/Makefile @@ -1,9 +1,10 @@ # SPDX-License-Identifier: GPL-2.0 # Samsung pin control drivers -obj-$(CONFIG_PINCTRL_SAMSUNG) += pinctrl-samsung.o -obj-$(CONFIG_PINCTRL_EXYNOS) += pinctrl-exynos.o -obj-$(CONFIG_PINCTRL_EXYNOS_ARM) += pinctrl-exynos-arm.o -obj-$(CONFIG_PINCTRL_EXYNOS_ARM64) += pinctrl-exynos-arm64.o -obj-$(CONFIG_PINCTRL_S3C24XX) += pinctrl-s3c24xx.o -obj-$(CONFIG_PINCTRL_S3C64XX) += pinctrl-s3c64xx.o +obj-$(CONFIG_PINCTRL_SAMSUNG) += pinctrl-samsung-super.o +pinctrl-samsung-super-$(CONFIG_PINCTRL_SAMSUNG) += pinctrl-samsung.o +pinctrl-samsung-super-$(CONFIG_PINCTRL_EXYNOS) += pinctrl-exynos.o +pinctrl-samsung-super-$(CONFIG_PINCTRL_EXYNOS_ARM) += pinctrl-exynos- arm.o +pinctrl-samsung-super-$(CONFIG_PINCTRL_EXYNOS_ARM64) += pinctrl-exynos- arm64.o +pinctrl-samsung-super-$(CONFIG_PINCTRL_S3C24XX) += pinctrl-s3c24xx.o +pinctrl-samsung-super-$(CONFIG_PINCTRL_S3C64XX) += pinctrl-s3c64xx.o diff --git a/drivers/pinctrl/samsung/pinctrl-exynos-arm.c b/drivers/pinctrl/samsung/pinctrl-exynos-arm.c index 85ddf49a5188..28906bf213c4 100644 --- a/drivers/pinctrl/samsung/pinctrl-exynos-arm.c +++ b/drivers/pinctrl/samsung/pinctrl-exynos-arm.c @@ -14,6 +14,7 @@ // external gpio and wakeup interrupt support. #include <linux/device.h> +#include <linux/module.h> #include <linux/of_address.h> #include <linux/slab.h> #include <linux/err.h> @@ -891,3 +892,4 @@ const struct samsung_pinctrl_of_match_data exynos5420_of_data __initconst = { .ctrl = exynos5420_pin_ctrl, .num_ctrl = ARRAY_SIZE(exynos5420_pin_ctrl), }; +MODULE_LICENSE("GPL"); diff --git a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c index b6e56422a700..2b19476ad5ff 100644 --- a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c +++ b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c @@ -14,6 +14,7 @@ // external gpio and wakeup interrupt support. #include <linux/slab.h> +#include <linux/module.h> #include <linux/soc/samsung/exynos-regs-pmu.h> #include "pinctrl-samsung.h" @@ -422,3 +423,4 @@ const struct samsung_pinctrl_of_match_data exynos7_of_data __initconst = { .ctrl = exynos7_pin_ctrl, .num_ctrl = ARRAY_SIZE(exynos7_pin_ctrl), }; +MODULE_LICENSE("GPL"); diff --git a/drivers/pinctrl/samsung/pinctrl-exynos.c b/drivers/pinctrl/samsung/pinctrl-exynos.c index ebc27b06718c..630d606330f1 100644 --- a/drivers/pinctrl/samsung/pinctrl-exynos.c +++ b/drivers/pinctrl/samsung/pinctrl-exynos.c @@ -18,6 +18,7 @@ #include <linux/irqdomain.h> #include <linux/irq.h> #include <linux/irqchip/chained_irq.h> +#include <linux/module.h> #include <linux/of.h> #include <linux/of_irq.h> #include <linux/slab.h> @@ -713,3 +714,4 @@ exynos_retention_init(struct samsung_pinctrl_drv_data *drvdata, return ctrl; } +MODULE_LICENSE("GPL"); diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.c b/drivers/pinctrl/samsung/pinctrl-samsung.c index de0477bb469d..4483eaed27f8 100644 --- a/drivers/pinctrl/samsung/pinctrl-samsung.c +++ b/drivers/pinctrl/samsung/pinctrl-samsung.c @@ -15,6 +15,7 @@ // but provides extensions to which platform specific implementation of the gpio // and wakeup interrupts can be hooked to. +#include <linux/module.h> #include <linux/init.h> #include <linux/platform_device.h> #include <linux/io.h> @@ -1275,6 +1276,7 @@ static const struct of_device_id samsung_pinctrl_dt_match[] = { #endif {}, }; +MODULE_DEVICE_TABLE(of, samsung_pinctrl_dt_match); static const struct dev_pm_ops samsung_pinctrl_pm_ops = { SET_LATE_SYSTEM_SLEEP_PM_OPS(samsung_pinctrl_suspend, @@ -1296,3 +1298,14 @@ static int __init samsung_pinctrl_drv_register(void) return platform_driver_register(&samsung_pinctrl_driver); } postcore_initcall(samsung_pinctrl_drv_register); + +static void __exit samsung_pinctrl_drv_unregister(void) +{ + platform_driver_unregister(&samsung_pinctrl_driver); +} +module_exit(samsung_pinctrl_drv_unregister); + + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Hyunki Koo <hyunki00.koo@samsung.com>"); +MODULE_DESCRIPTION("Samsung Exynos PINCTRL driver"); -- 2.15.0.rc1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 12+ messages in thread
* Re: [PATCH] pinctrl: samsung: modularize samsung pinctrl driver 2019-11-21 7:26 ` 구현기 @ 2019-11-21 7:38 ` Krzysztof Kozlowski -1 siblings, 0 replies; 12+ messages in thread From: Krzysztof Kozlowski @ 2019-11-21 7:38 UTC (permalink / raw) To: 구현기 Cc: Tomasz Figa, s.nawrocki, linus.walleij, linux-arm-kernel, linux-samsung-soc, linux-gpio, linux-kernel Hi, Thanks for the patch. Few comments below: On Thu, 21 Nov 2019 at 15:26, 구현기 <hyunki00.koo@samsung.com> wrote: > > Enable samsung pinctrl driver to be compiled as modules. Why? What's the benefit? Are platforms capable of such boot? Pinctrl is needed early - even before mounting rootfs... What about module unloading? Is it reasonable? Please answer to all this also in commit message. > > Change-Id: I92a9953c92831a316f7f50146898ff19831549ec This does not belong to Git. > Signed-off-by: Hyunki Koo <hyunki00.koo@samsung.com> You "From" name is different than written here in Signed-off-by. They should match and I do not know Korean to be able to tell whether they really match or not :). How about using Latin transliteration also in "From" field? > --- > drivers/pinctrl/samsung/Kconfig | 5 +---- > drivers/pinctrl/samsung/Makefile | 13 +++++++------ > drivers/pinctrl/samsung/pinctrl-exynos-arm.c | 2 ++ > drivers/pinctrl/samsung/pinctrl-exynos-arm64.c | 2 ++ > drivers/pinctrl/samsung/pinctrl-exynos.c | 2 ++ > drivers/pinctrl/samsung/pinctrl-samsung.c | 13 +++++++++++++ > 6 files changed, 27 insertions(+), 10 deletions(-) > > diff --git a/drivers/pinctrl/samsung/Kconfig > b/drivers/pinctrl/samsung/Kconfig > index 425fadd6c346..25e16984ef23 100644 > --- a/drivers/pinctrl/samsung/Kconfig > +++ b/drivers/pinctrl/samsung/Kconfig > @@ -3,14 +3,13 @@ > # Samsung Pin control drivers > # > config PINCTRL_SAMSUNG > - bool > + tristate "Pinctrl driver data for Samsung SoCs" > select PINMUX > select PINCONF > > config PINCTRL_EXYNOS > bool "Pinctrl driver data for Samsung EXYNOS SoCs" > depends on OF && GPIOLIB && (ARCH_EXYNOS || ARCH_S5PV210) > - select PINCTRL_SAMSUNG > select PINCTRL_EXYNOS_ARM if ARM && (ARCH_EXYNOS || ARCH_S5PV210) > select PINCTRL_EXYNOS_ARM64 if ARM64 && ARCH_EXYNOS > > @@ -25,9 +24,7 @@ config PINCTRL_EXYNOS_ARM64 > config PINCTRL_S3C24XX > bool "Samsung S3C24XX SoC pinctrl driver" > depends on ARCH_S3C24XX && OF > - select PINCTRL_SAMSUNG > > config PINCTRL_S3C64XX > bool "Samsung S3C64XX SoC pinctrl driver" > depends on ARCH_S3C64XX > - select PINCTRL_SAMSUNG > diff --git a/drivers/pinctrl/samsung/Makefile > b/drivers/pinctrl/samsung/Makefile > index ed951df6a112..b3ac01838b8a 100644 > --- a/drivers/pinctrl/samsung/Makefile > +++ b/drivers/pinctrl/samsung/Makefile > @@ -1,9 +1,10 @@ > # SPDX-License-Identifier: GPL-2.0 > # Samsung pin control drivers > > -obj-$(CONFIG_PINCTRL_SAMSUNG) += pinctrl-samsung.o > -obj-$(CONFIG_PINCTRL_EXYNOS) += pinctrl-exynos.o > -obj-$(CONFIG_PINCTRL_EXYNOS_ARM) += pinctrl-exynos-arm.o > -obj-$(CONFIG_PINCTRL_EXYNOS_ARM64) += pinctrl-exynos-arm64.o > -obj-$(CONFIG_PINCTRL_S3C24XX) += pinctrl-s3c24xx.o > -obj-$(CONFIG_PINCTRL_S3C64XX) += pinctrl-s3c64xx.o > +obj-$(CONFIG_PINCTRL_SAMSUNG) += pinctrl-samsung-super.o > +pinctrl-samsung-super-$(CONFIG_PINCTRL_SAMSUNG) += pinctrl-samsung.o > +pinctrl-samsung-super-$(CONFIG_PINCTRL_EXYNOS) += pinctrl-exynos.o > +pinctrl-samsung-super-$(CONFIG_PINCTRL_EXYNOS_ARM) += pinctrl-exynos- > arm.o > +pinctrl-samsung-super-$(CONFIG_PINCTRL_EXYNOS_ARM64) += pinctrl-exynos- > arm64.o > +pinctrl-samsung-super-$(CONFIG_PINCTRL_S3C24XX) += pinctrl-s3c24xx.o > +pinctrl-samsung-super-$(CONFIG_PINCTRL_S3C64XX) += pinctrl-s3c64xx.o I don't get why you need to rename obj to pinctrl-samsung-super? > diff --git a/drivers/pinctrl/samsung/pinctrl-exynos-arm.c > b/drivers/pinctrl/samsung/pinctrl-exynos-arm.c > index 85ddf49a5188..28906bf213c4 100644 > --- a/drivers/pinctrl/samsung/pinctrl-exynos-arm.c > +++ b/drivers/pinctrl/samsung/pinctrl-exynos-arm.c > @@ -14,6 +14,7 @@ > // external gpio and wakeup interrupt support. > > #include <linux/device.h> > +#include <linux/module.h> > #include <linux/of_address.h> > #include <linux/slab.h> > #include <linux/err.h> > @@ -891,3 +892,4 @@ const struct samsung_pinctrl_of_match_data > exynos5420_of_data __initconst = { > .ctrl = exynos5420_pin_ctrl, > .num_ctrl = ARRAY_SIZE(exynos5420_pin_ctrl), > }; > +MODULE_LICENSE("GPL"); > diff --git a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c > b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c > index b6e56422a700..2b19476ad5ff 100644 > --- a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c > +++ b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c > @@ -14,6 +14,7 @@ > // external gpio and wakeup interrupt support. > > #include <linux/slab.h> > +#include <linux/module.h> > #include <linux/soc/samsung/exynos-regs-pmu.h> > > #include "pinctrl-samsung.h" > @@ -422,3 +423,4 @@ const struct samsung_pinctrl_of_match_data > exynos7_of_data __initconst = { > .ctrl = exynos7_pin_ctrl, > .num_ctrl = ARRAY_SIZE(exynos7_pin_ctrl), > }; > +MODULE_LICENSE("GPL"); > diff --git a/drivers/pinctrl/samsung/pinctrl-exynos.c > b/drivers/pinctrl/samsung/pinctrl-exynos.c > index ebc27b06718c..630d606330f1 100644 > --- a/drivers/pinctrl/samsung/pinctrl-exynos.c > +++ b/drivers/pinctrl/samsung/pinctrl-exynos.c > @@ -18,6 +18,7 @@ > #include <linux/irqdomain.h> > #include <linux/irq.h> > #include <linux/irqchip/chained_irq.h> > +#include <linux/module.h> > #include <linux/of.h> > #include <linux/of_irq.h> > #include <linux/slab.h> > @@ -713,3 +714,4 @@ exynos_retention_init(struct samsung_pinctrl_drv_data > *drvdata, > > return ctrl; > } > +MODULE_LICENSE("GPL"); > diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.c > b/drivers/pinctrl/samsung/pinctrl-samsung.c > index de0477bb469d..4483eaed27f8 100644 > --- a/drivers/pinctrl/samsung/pinctrl-samsung.c > +++ b/drivers/pinctrl/samsung/pinctrl-samsung.c > @@ -15,6 +15,7 @@ > // but provides extensions to which platform specific implementation of > the gpio > // and wakeup interrupts can be hooked to. > > +#include <linux/module.h> > #include <linux/init.h> > #include <linux/platform_device.h> > #include <linux/io.h> > @@ -1275,6 +1276,7 @@ static const struct of_device_id > samsung_pinctrl_dt_match[] = { > #endif > {}, > }; > +MODULE_DEVICE_TABLE(of, samsung_pinctrl_dt_match); > > static const struct dev_pm_ops samsung_pinctrl_pm_ops = { > SET_LATE_SYSTEM_SLEEP_PM_OPS(samsung_pinctrl_suspend, > @@ -1296,3 +1298,14 @@ static int __init samsung_pinctrl_drv_register(void) > return platform_driver_register(&samsung_pinctrl_driver); > } > postcore_initcall(samsung_pinctrl_drv_register); > + > +static void __exit samsung_pinctrl_drv_unregister(void) > +{ > + platform_driver_unregister(&samsung_pinctrl_driver); > +} > +module_exit(samsung_pinctrl_drv_unregister); Since .suppress_bind_attrs are defined, I find it weird to be able to unload module... Another warning sign... > + > + > +MODULE_LICENSE("GPL"); > +MODULE_AUTHOR("Hyunki Koo <hyunki00.koo@samsung.com>"); I cannot find any contributions to this file from you. The author should be the main contributor(s). You need to go through history... > +MODULE_DESCRIPTION("Samsung Exynos PINCTRL driver"); That's not Exynos but Samsung-generic part... Samsung Exynos/S3C/S5P pinctrl driver. Best regards, Krzysztof ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH] pinctrl: samsung: modularize samsung pinctrl driver @ 2019-11-21 7:38 ` Krzysztof Kozlowski 0 siblings, 0 replies; 12+ messages in thread From: Krzysztof Kozlowski @ 2019-11-21 7:38 UTC (permalink / raw) To: 구현기 Cc: linux-samsung-soc, linus.walleij, Tomasz Figa, linux-kernel, linux-gpio, s.nawrocki, linux-arm-kernel Hi, Thanks for the patch. Few comments below: On Thu, 21 Nov 2019 at 15:26, 구현기 <hyunki00.koo@samsung.com> wrote: > > Enable samsung pinctrl driver to be compiled as modules. Why? What's the benefit? Are platforms capable of such boot? Pinctrl is needed early - even before mounting rootfs... What about module unloading? Is it reasonable? Please answer to all this also in commit message. > > Change-Id: I92a9953c92831a316f7f50146898ff19831549ec This does not belong to Git. > Signed-off-by: Hyunki Koo <hyunki00.koo@samsung.com> You "From" name is different than written here in Signed-off-by. They should match and I do not know Korean to be able to tell whether they really match or not :). How about using Latin transliteration also in "From" field? > --- > drivers/pinctrl/samsung/Kconfig | 5 +---- > drivers/pinctrl/samsung/Makefile | 13 +++++++------ > drivers/pinctrl/samsung/pinctrl-exynos-arm.c | 2 ++ > drivers/pinctrl/samsung/pinctrl-exynos-arm64.c | 2 ++ > drivers/pinctrl/samsung/pinctrl-exynos.c | 2 ++ > drivers/pinctrl/samsung/pinctrl-samsung.c | 13 +++++++++++++ > 6 files changed, 27 insertions(+), 10 deletions(-) > > diff --git a/drivers/pinctrl/samsung/Kconfig > b/drivers/pinctrl/samsung/Kconfig > index 425fadd6c346..25e16984ef23 100644 > --- a/drivers/pinctrl/samsung/Kconfig > +++ b/drivers/pinctrl/samsung/Kconfig > @@ -3,14 +3,13 @@ > # Samsung Pin control drivers > # > config PINCTRL_SAMSUNG > - bool > + tristate "Pinctrl driver data for Samsung SoCs" > select PINMUX > select PINCONF > > config PINCTRL_EXYNOS > bool "Pinctrl driver data for Samsung EXYNOS SoCs" > depends on OF && GPIOLIB && (ARCH_EXYNOS || ARCH_S5PV210) > - select PINCTRL_SAMSUNG > select PINCTRL_EXYNOS_ARM if ARM && (ARCH_EXYNOS || ARCH_S5PV210) > select PINCTRL_EXYNOS_ARM64 if ARM64 && ARCH_EXYNOS > > @@ -25,9 +24,7 @@ config PINCTRL_EXYNOS_ARM64 > config PINCTRL_S3C24XX > bool "Samsung S3C24XX SoC pinctrl driver" > depends on ARCH_S3C24XX && OF > - select PINCTRL_SAMSUNG > > config PINCTRL_S3C64XX > bool "Samsung S3C64XX SoC pinctrl driver" > depends on ARCH_S3C64XX > - select PINCTRL_SAMSUNG > diff --git a/drivers/pinctrl/samsung/Makefile > b/drivers/pinctrl/samsung/Makefile > index ed951df6a112..b3ac01838b8a 100644 > --- a/drivers/pinctrl/samsung/Makefile > +++ b/drivers/pinctrl/samsung/Makefile > @@ -1,9 +1,10 @@ > # SPDX-License-Identifier: GPL-2.0 > # Samsung pin control drivers > > -obj-$(CONFIG_PINCTRL_SAMSUNG) += pinctrl-samsung.o > -obj-$(CONFIG_PINCTRL_EXYNOS) += pinctrl-exynos.o > -obj-$(CONFIG_PINCTRL_EXYNOS_ARM) += pinctrl-exynos-arm.o > -obj-$(CONFIG_PINCTRL_EXYNOS_ARM64) += pinctrl-exynos-arm64.o > -obj-$(CONFIG_PINCTRL_S3C24XX) += pinctrl-s3c24xx.o > -obj-$(CONFIG_PINCTRL_S3C64XX) += pinctrl-s3c64xx.o > +obj-$(CONFIG_PINCTRL_SAMSUNG) += pinctrl-samsung-super.o > +pinctrl-samsung-super-$(CONFIG_PINCTRL_SAMSUNG) += pinctrl-samsung.o > +pinctrl-samsung-super-$(CONFIG_PINCTRL_EXYNOS) += pinctrl-exynos.o > +pinctrl-samsung-super-$(CONFIG_PINCTRL_EXYNOS_ARM) += pinctrl-exynos- > arm.o > +pinctrl-samsung-super-$(CONFIG_PINCTRL_EXYNOS_ARM64) += pinctrl-exynos- > arm64.o > +pinctrl-samsung-super-$(CONFIG_PINCTRL_S3C24XX) += pinctrl-s3c24xx.o > +pinctrl-samsung-super-$(CONFIG_PINCTRL_S3C64XX) += pinctrl-s3c64xx.o I don't get why you need to rename obj to pinctrl-samsung-super? > diff --git a/drivers/pinctrl/samsung/pinctrl-exynos-arm.c > b/drivers/pinctrl/samsung/pinctrl-exynos-arm.c > index 85ddf49a5188..28906bf213c4 100644 > --- a/drivers/pinctrl/samsung/pinctrl-exynos-arm.c > +++ b/drivers/pinctrl/samsung/pinctrl-exynos-arm.c > @@ -14,6 +14,7 @@ > // external gpio and wakeup interrupt support. > > #include <linux/device.h> > +#include <linux/module.h> > #include <linux/of_address.h> > #include <linux/slab.h> > #include <linux/err.h> > @@ -891,3 +892,4 @@ const struct samsung_pinctrl_of_match_data > exynos5420_of_data __initconst = { > .ctrl = exynos5420_pin_ctrl, > .num_ctrl = ARRAY_SIZE(exynos5420_pin_ctrl), > }; > +MODULE_LICENSE("GPL"); > diff --git a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c > b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c > index b6e56422a700..2b19476ad5ff 100644 > --- a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c > +++ b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c > @@ -14,6 +14,7 @@ > // external gpio and wakeup interrupt support. > > #include <linux/slab.h> > +#include <linux/module.h> > #include <linux/soc/samsung/exynos-regs-pmu.h> > > #include "pinctrl-samsung.h" > @@ -422,3 +423,4 @@ const struct samsung_pinctrl_of_match_data > exynos7_of_data __initconst = { > .ctrl = exynos7_pin_ctrl, > .num_ctrl = ARRAY_SIZE(exynos7_pin_ctrl), > }; > +MODULE_LICENSE("GPL"); > diff --git a/drivers/pinctrl/samsung/pinctrl-exynos.c > b/drivers/pinctrl/samsung/pinctrl-exynos.c > index ebc27b06718c..630d606330f1 100644 > --- a/drivers/pinctrl/samsung/pinctrl-exynos.c > +++ b/drivers/pinctrl/samsung/pinctrl-exynos.c > @@ -18,6 +18,7 @@ > #include <linux/irqdomain.h> > #include <linux/irq.h> > #include <linux/irqchip/chained_irq.h> > +#include <linux/module.h> > #include <linux/of.h> > #include <linux/of_irq.h> > #include <linux/slab.h> > @@ -713,3 +714,4 @@ exynos_retention_init(struct samsung_pinctrl_drv_data > *drvdata, > > return ctrl; > } > +MODULE_LICENSE("GPL"); > diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.c > b/drivers/pinctrl/samsung/pinctrl-samsung.c > index de0477bb469d..4483eaed27f8 100644 > --- a/drivers/pinctrl/samsung/pinctrl-samsung.c > +++ b/drivers/pinctrl/samsung/pinctrl-samsung.c > @@ -15,6 +15,7 @@ > // but provides extensions to which platform specific implementation of > the gpio > // and wakeup interrupts can be hooked to. > > +#include <linux/module.h> > #include <linux/init.h> > #include <linux/platform_device.h> > #include <linux/io.h> > @@ -1275,6 +1276,7 @@ static const struct of_device_id > samsung_pinctrl_dt_match[] = { > #endif > {}, > }; > +MODULE_DEVICE_TABLE(of, samsung_pinctrl_dt_match); > > static const struct dev_pm_ops samsung_pinctrl_pm_ops = { > SET_LATE_SYSTEM_SLEEP_PM_OPS(samsung_pinctrl_suspend, > @@ -1296,3 +1298,14 @@ static int __init samsung_pinctrl_drv_register(void) > return platform_driver_register(&samsung_pinctrl_driver); > } > postcore_initcall(samsung_pinctrl_drv_register); > + > +static void __exit samsung_pinctrl_drv_unregister(void) > +{ > + platform_driver_unregister(&samsung_pinctrl_driver); > +} > +module_exit(samsung_pinctrl_drv_unregister); Since .suppress_bind_attrs are defined, I find it weird to be able to unload module... Another warning sign... > + > + > +MODULE_LICENSE("GPL"); > +MODULE_AUTHOR("Hyunki Koo <hyunki00.koo@samsung.com>"); I cannot find any contributions to this file from you. The author should be the main contributor(s). You need to go through history... > +MODULE_DESCRIPTION("Samsung Exynos PINCTRL driver"); That's not Exynos but Samsung-generic part... Samsung Exynos/S3C/S5P pinctrl driver. Best regards, Krzysztof _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 12+ messages in thread
* RE: [PATCH] pinctrl: samsung: modularize samsung pinctrl driver 2019-11-21 7:38 ` Krzysztof Kozlowski @ 2019-11-26 1:14 ` Hyunki Koo -1 siblings, 0 replies; 12+ messages in thread From: Hyunki Koo @ 2019-11-26 1:14 UTC (permalink / raw) To: 'Krzysztof Kozlowski' Cc: 'Tomasz Figa', s.nawrocki, linus.walleij, linux-arm-kernel, linux-samsung-soc, linux-gpio, linux-kernel On Thu, 21 Nov 2019 at 16:38, Krzysztof Kozlowski <krzk@kernel.org> wrote: > Hi, > > Thanks for the patch. Few comments below: > > On Thu, 21 Nov 2019 at 15:26, 구현기 <hyunki00.koo@samsung.com> wrote: >> >> Enable samsung pinctrl driver to be compiled as modules. > > Why? What's the benefit? Are platforms capable of such boot? Pinctrl is needed early - even before mounting rootfs... > What about module unloading? Is it reasonable? > Please answer to all this also in commit message. > Sorry to late and Thank you for your comment, I would like to apply GKI on the pinctrl driver So I would like to cut off dependency from ARCH_EXYNOS. I will split into two part, First, cut off the dependency with ARCH_EXYNOS in arch/arm64/Kconfig.platform. Second, I will make the pinctrl driver as a module. >> >> Change-Id: I92a9953c92831a316f7f50146898ff19831549ec > > This does not belong to Git. > >> Signed-off-by: Hyunki Koo <hyunki00.koo@samsung.com> > >You "From" name is different than written here in Signed-off-by. They should match and I do not know Korean to be able to tell whether they really match or not :). >How about using Latin transliteration also in "From" field? > >> --- >> drivers/pinctrl/samsung/Kconfig | 5 +---- >> drivers/pinctrl/samsung/Makefile | 13 +++++++------ >> drivers/pinctrl/samsung/pinctrl-exynos-arm.c | 2 ++ >> drivers/pinctrl/samsung/pinctrl-exynos-arm64.c | 2 ++ >> drivers/pinctrl/samsung/pinctrl-exynos.c | 2 ++ >> drivers/pinctrl/samsung/pinctrl-samsung.c | 13 +++++++++++++ >> 6 files changed, 27 insertions(+), 10 deletions(-) >> >> diff --git a/drivers/pinctrl/samsung/Kconfig >> b/drivers/pinctrl/samsung/Kconfig index 425fadd6c346..25e16984ef23 >> 100644 >> --- a/drivers/pinctrl/samsung/Kconfig >> +++ b/drivers/pinctrl/samsung/Kconfig >> @@ -3,14 +3,13 @@ >> # Samsung Pin control drivers >> # >> config PINCTRL_SAMSUNG >> - bool >> + tristate "Pinctrl driver data for Samsung SoCs" >> select PINMUX >> select PINCONF >> >> config PINCTRL_EXYNOS >> bool "Pinctrl driver data for Samsung EXYNOS SoCs" >> depends on OF && GPIOLIB && (ARCH_EXYNOS || ARCH_S5PV210) >> - select PINCTRL_SAMSUNG >> select PINCTRL_EXYNOS_ARM if ARM && (ARCH_EXYNOS || ARCH_S5PV210) >> select PINCTRL_EXYNOS_ARM64 if ARM64 && ARCH_EXYNOS >> >> @@ -25,9 +24,7 @@ config PINCTRL_EXYNOS_ARM64 config PINCTRL_S3C24XX >> bool "Samsung S3C24XX SoC pinctrl driver" >> depends on ARCH_S3C24XX && OF >> - select PINCTRL_SAMSUNG >> >> config PINCTRL_S3C64XX >> bool "Samsung S3C64XX SoC pinctrl driver" >> depends on ARCH_S3C64XX >> - select PINCTRL_SAMSUNG >> diff --git a/drivers/pinctrl/samsung/Makefile >> b/drivers/pinctrl/samsung/Makefile >> index ed951df6a112..b3ac01838b8a 100644 >> --- a/drivers/pinctrl/samsung/Makefile >> +++ b/drivers/pinctrl/samsung/Makefile >> @@ -1,9 +1,10 @@ >> # SPDX-License-Identifier: GPL-2.0 >> # Samsung pin control drivers >> >> -obj-$(CONFIG_PINCTRL_SAMSUNG) += pinctrl-samsung.o >> -obj-$(CONFIG_PINCTRL_EXYNOS) += pinctrl-exynos.o >> -obj-$(CONFIG_PINCTRL_EXYNOS_ARM) += pinctrl-exynos-arm.o >> -obj-$(CONFIG_PINCTRL_EXYNOS_ARM64) += pinctrl-exynos-arm64.o >> -obj-$(CONFIG_PINCTRL_S3C24XX) += pinctrl-s3c24xx.o >> -obj-$(CONFIG_PINCTRL_S3C64XX) += pinctrl-s3c64xx.o >> +obj-$(CONFIG_PINCTRL_SAMSUNG) += pinctrl-samsung-super.o >> +pinctrl-samsung-super-$(CONFIG_PINCTRL_SAMSUNG) += pinctrl-samsung.o >> +pinctrl-samsung-super-$(CONFIG_PINCTRL_EXYNOS) += pinctrl-exynos.o >> +pinctrl-samsung-super-$(CONFIG_PINCTRL_EXYNOS_ARM) += pinctrl-exynos- >> arm.o >> +pinctrl-samsung-super-$(CONFIG_PINCTRL_EXYNOS_ARM64) += pinctrl-exynos- >> arm64.o >> +pinctrl-samsung-super-$(CONFIG_PINCTRL_S3C24XX) += pinctrl-s3c24xx.o >> +pinctrl-samsung-super-$(CONFIG_PINCTRL_S3C64XX) += pinctrl-s3c64xx.o > > I don't get why you need to rename obj to pinctrl-samsung-super? I would like to make pinctrl as a super module. It is many dependency between pinctrl-exynos, pinctr-exynos-arm64 and pinctrl-samsung > >> diff --git a/drivers/pinctrl/samsung/pinctrl-exynos-arm.c >> b/drivers/pinctrl/samsung/pinctrl-exynos-arm.c >> index 85ddf49a5188..28906bf213c4 100644 >> --- a/drivers/pinctrl/samsung/pinctrl-exynos-arm.c >> +++ b/drivers/pinctrl/samsung/pinctrl-exynos-arm.c >> @@ -14,6 +14,7 @@ >> // external gpio and wakeup interrupt support. >> >> #include <linux/device.h> >> +#include <linux/module.h> >> #include <linux/of_address.h> >> #include <linux/slab.h> >> #include <linux/err.h> >> @@ -891,3 +892,4 @@ const struct samsung_pinctrl_of_match_data >> exynos5420_of_data __initconst = { >> .ctrl = exynos5420_pin_ctrl, >> .num_ctrl = ARRAY_SIZE(exynos5420_pin_ctrl), >> }; >> +MODULE_LICENSE("GPL"); >> diff --git a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c >> b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c >> index b6e56422a700..2b19476ad5ff 100644 >> --- a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c >> +++ b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c >> @@ -14,6 +14,7 @@ >> // external gpio and wakeup interrupt support. >> >> #include <linux/slab.h> >> +#include <linux/module.h> >> #include <linux/soc/samsung/exynos-regs-pmu.h> >> >> #include "pinctrl-samsung.h" >> @@ -422,3 +423,4 @@ const struct samsung_pinctrl_of_match_data >> exynos7_of_data __initconst = { >> .ctrl = exynos7_pin_ctrl, >> .num_ctrl = ARRAY_SIZE(exynos7_pin_ctrl), >> }; >> +MODULE_LICENSE("GPL"); >> diff --git a/drivers/pinctrl/samsung/pinctrl-exynos.c >> b/drivers/pinctrl/samsung/pinctrl-exynos.c >> index ebc27b06718c..630d606330f1 100644 >> --- a/drivers/pinctrl/samsung/pinctrl-exynos.c >> +++ b/drivers/pinctrl/samsung/pinctrl-exynos.c >> @@ -18,6 +18,7 @@ >> #include <linux/irqdomain.h> >> #include <linux/irq.h> >> #include <linux/irqchip/chained_irq.h> >> +#include <linux/module.h> >> #include <linux/of.h> >> #include <linux/of_irq.h> >> #include <linux/slab.h> >> @@ -713,3 +714,4 @@ exynos_retention_init(struct >> samsung_pinctrl_drv_data *drvdata, >> >> return ctrl; >> } >> +MODULE_LICENSE("GPL"); >> diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.c >> b/drivers/pinctrl/samsung/pinctrl-samsung.c >> index de0477bb469d..4483eaed27f8 100644 >> --- a/drivers/pinctrl/samsung/pinctrl-samsung.c >> +++ b/drivers/pinctrl/samsung/pinctrl-samsung.c >> @@ -15,6 +15,7 @@ >> // but provides extensions to which platform specific implementation >> of the gpio // and wakeup interrupts can be hooked to. >> >> +#include <linux/module.h> >> #include <linux/init.h> >> #include <linux/platform_device.h> >> #include <linux/io.h> >> @@ -1275,6 +1276,7 @@ static const struct of_device_id >> samsung_pinctrl_dt_match[] = { #endif >> {}, >> }; >> +MODULE_DEVICE_TABLE(of, samsung_pinctrl_dt_match); >> >> static const struct dev_pm_ops samsung_pinctrl_pm_ops = { >> SET_LATE_SYSTEM_SLEEP_PM_OPS(samsung_pinctrl_suspend, >> @@ -1296,3 +1298,14 @@ static int __init samsung_pinctrl_drv_register(void) >> return platform_driver_register(&samsung_pinctrl_driver); >> } >> postcore_initcall(samsung_pinctrl_drv_register); >> + >> +static void __exit samsung_pinctrl_drv_unregister(void) >> +{ >> + platform_driver_unregister(&samsung_pinctrl_driver); >> +} >> +module_exit(samsung_pinctrl_drv_unregister); > > Since .suppress_bind_attrs are defined, I find it weird to be able to unload module... Another warning sign... Okay I will apply your comment > >> + >> + >> +MODULE_LICENSE("GPL"); >> +MODULE_AUTHOR("Hyunki Koo <hyunki00.koo@samsung.com>"); > > I cannot find any contributions to this file from you. The author should be the main contributor(s). You need to go through history... > >> +MODULE_DESCRIPTION("Samsung Exynos PINCTRL driver"); > > That's not Exynos but Samsung-generic part... Samsung Exynos/S3C/S5P pinctrl driver. > Okay I will apply your comment ^ permalink raw reply [flat|nested] 12+ messages in thread
* RE: [PATCH] pinctrl: samsung: modularize samsung pinctrl driver @ 2019-11-26 1:14 ` Hyunki Koo 0 siblings, 0 replies; 12+ messages in thread From: Hyunki Koo @ 2019-11-26 1:14 UTC (permalink / raw) To: 'Krzysztof Kozlowski' Cc: linux-samsung-soc, linus.walleij, 'Tomasz Figa', linux-kernel, linux-gpio, s.nawrocki, linux-arm-kernel On Thu, 21 Nov 2019 at 16:38, Krzysztof Kozlowski <krzk@kernel.org> wrote: > Hi, > > Thanks for the patch. Few comments below: > > On Thu, 21 Nov 2019 at 15:26, 구현기 <hyunki00.koo@samsung.com> wrote: >> >> Enable samsung pinctrl driver to be compiled as modules. > > Why? What's the benefit? Are platforms capable of such boot? Pinctrl is needed early - even before mounting rootfs... > What about module unloading? Is it reasonable? > Please answer to all this also in commit message. > Sorry to late and Thank you for your comment, I would like to apply GKI on the pinctrl driver So I would like to cut off dependency from ARCH_EXYNOS. I will split into two part, First, cut off the dependency with ARCH_EXYNOS in arch/arm64/Kconfig.platform. Second, I will make the pinctrl driver as a module. >> >> Change-Id: I92a9953c92831a316f7f50146898ff19831549ec > > This does not belong to Git. > >> Signed-off-by: Hyunki Koo <hyunki00.koo@samsung.com> > >You "From" name is different than written here in Signed-off-by. They should match and I do not know Korean to be able to tell whether they really match or not :). >How about using Latin transliteration also in "From" field? > >> --- >> drivers/pinctrl/samsung/Kconfig | 5 +---- >> drivers/pinctrl/samsung/Makefile | 13 +++++++------ >> drivers/pinctrl/samsung/pinctrl-exynos-arm.c | 2 ++ >> drivers/pinctrl/samsung/pinctrl-exynos-arm64.c | 2 ++ >> drivers/pinctrl/samsung/pinctrl-exynos.c | 2 ++ >> drivers/pinctrl/samsung/pinctrl-samsung.c | 13 +++++++++++++ >> 6 files changed, 27 insertions(+), 10 deletions(-) >> >> diff --git a/drivers/pinctrl/samsung/Kconfig >> b/drivers/pinctrl/samsung/Kconfig index 425fadd6c346..25e16984ef23 >> 100644 >> --- a/drivers/pinctrl/samsung/Kconfig >> +++ b/drivers/pinctrl/samsung/Kconfig >> @@ -3,14 +3,13 @@ >> # Samsung Pin control drivers >> # >> config PINCTRL_SAMSUNG >> - bool >> + tristate "Pinctrl driver data for Samsung SoCs" >> select PINMUX >> select PINCONF >> >> config PINCTRL_EXYNOS >> bool "Pinctrl driver data for Samsung EXYNOS SoCs" >> depends on OF && GPIOLIB && (ARCH_EXYNOS || ARCH_S5PV210) >> - select PINCTRL_SAMSUNG >> select PINCTRL_EXYNOS_ARM if ARM && (ARCH_EXYNOS || ARCH_S5PV210) >> select PINCTRL_EXYNOS_ARM64 if ARM64 && ARCH_EXYNOS >> >> @@ -25,9 +24,7 @@ config PINCTRL_EXYNOS_ARM64 config PINCTRL_S3C24XX >> bool "Samsung S3C24XX SoC pinctrl driver" >> depends on ARCH_S3C24XX && OF >> - select PINCTRL_SAMSUNG >> >> config PINCTRL_S3C64XX >> bool "Samsung S3C64XX SoC pinctrl driver" >> depends on ARCH_S3C64XX >> - select PINCTRL_SAMSUNG >> diff --git a/drivers/pinctrl/samsung/Makefile >> b/drivers/pinctrl/samsung/Makefile >> index ed951df6a112..b3ac01838b8a 100644 >> --- a/drivers/pinctrl/samsung/Makefile >> +++ b/drivers/pinctrl/samsung/Makefile >> @@ -1,9 +1,10 @@ >> # SPDX-License-Identifier: GPL-2.0 >> # Samsung pin control drivers >> >> -obj-$(CONFIG_PINCTRL_SAMSUNG) += pinctrl-samsung.o >> -obj-$(CONFIG_PINCTRL_EXYNOS) += pinctrl-exynos.o >> -obj-$(CONFIG_PINCTRL_EXYNOS_ARM) += pinctrl-exynos-arm.o >> -obj-$(CONFIG_PINCTRL_EXYNOS_ARM64) += pinctrl-exynos-arm64.o >> -obj-$(CONFIG_PINCTRL_S3C24XX) += pinctrl-s3c24xx.o >> -obj-$(CONFIG_PINCTRL_S3C64XX) += pinctrl-s3c64xx.o >> +obj-$(CONFIG_PINCTRL_SAMSUNG) += pinctrl-samsung-super.o >> +pinctrl-samsung-super-$(CONFIG_PINCTRL_SAMSUNG) += pinctrl-samsung.o >> +pinctrl-samsung-super-$(CONFIG_PINCTRL_EXYNOS) += pinctrl-exynos.o >> +pinctrl-samsung-super-$(CONFIG_PINCTRL_EXYNOS_ARM) += pinctrl-exynos- >> arm.o >> +pinctrl-samsung-super-$(CONFIG_PINCTRL_EXYNOS_ARM64) += pinctrl-exynos- >> arm64.o >> +pinctrl-samsung-super-$(CONFIG_PINCTRL_S3C24XX) += pinctrl-s3c24xx.o >> +pinctrl-samsung-super-$(CONFIG_PINCTRL_S3C64XX) += pinctrl-s3c64xx.o > > I don't get why you need to rename obj to pinctrl-samsung-super? I would like to make pinctrl as a super module. It is many dependency between pinctrl-exynos, pinctr-exynos-arm64 and pinctrl-samsung > >> diff --git a/drivers/pinctrl/samsung/pinctrl-exynos-arm.c >> b/drivers/pinctrl/samsung/pinctrl-exynos-arm.c >> index 85ddf49a5188..28906bf213c4 100644 >> --- a/drivers/pinctrl/samsung/pinctrl-exynos-arm.c >> +++ b/drivers/pinctrl/samsung/pinctrl-exynos-arm.c >> @@ -14,6 +14,7 @@ >> // external gpio and wakeup interrupt support. >> >> #include <linux/device.h> >> +#include <linux/module.h> >> #include <linux/of_address.h> >> #include <linux/slab.h> >> #include <linux/err.h> >> @@ -891,3 +892,4 @@ const struct samsung_pinctrl_of_match_data >> exynos5420_of_data __initconst = { >> .ctrl = exynos5420_pin_ctrl, >> .num_ctrl = ARRAY_SIZE(exynos5420_pin_ctrl), >> }; >> +MODULE_LICENSE("GPL"); >> diff --git a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c >> b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c >> index b6e56422a700..2b19476ad5ff 100644 >> --- a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c >> +++ b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c >> @@ -14,6 +14,7 @@ >> // external gpio and wakeup interrupt support. >> >> #include <linux/slab.h> >> +#include <linux/module.h> >> #include <linux/soc/samsung/exynos-regs-pmu.h> >> >> #include "pinctrl-samsung.h" >> @@ -422,3 +423,4 @@ const struct samsung_pinctrl_of_match_data >> exynos7_of_data __initconst = { >> .ctrl = exynos7_pin_ctrl, >> .num_ctrl = ARRAY_SIZE(exynos7_pin_ctrl), >> }; >> +MODULE_LICENSE("GPL"); >> diff --git a/drivers/pinctrl/samsung/pinctrl-exynos.c >> b/drivers/pinctrl/samsung/pinctrl-exynos.c >> index ebc27b06718c..630d606330f1 100644 >> --- a/drivers/pinctrl/samsung/pinctrl-exynos.c >> +++ b/drivers/pinctrl/samsung/pinctrl-exynos.c >> @@ -18,6 +18,7 @@ >> #include <linux/irqdomain.h> >> #include <linux/irq.h> >> #include <linux/irqchip/chained_irq.h> >> +#include <linux/module.h> >> #include <linux/of.h> >> #include <linux/of_irq.h> >> #include <linux/slab.h> >> @@ -713,3 +714,4 @@ exynos_retention_init(struct >> samsung_pinctrl_drv_data *drvdata, >> >> return ctrl; >> } >> +MODULE_LICENSE("GPL"); >> diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.c >> b/drivers/pinctrl/samsung/pinctrl-samsung.c >> index de0477bb469d..4483eaed27f8 100644 >> --- a/drivers/pinctrl/samsung/pinctrl-samsung.c >> +++ b/drivers/pinctrl/samsung/pinctrl-samsung.c >> @@ -15,6 +15,7 @@ >> // but provides extensions to which platform specific implementation >> of the gpio // and wakeup interrupts can be hooked to. >> >> +#include <linux/module.h> >> #include <linux/init.h> >> #include <linux/platform_device.h> >> #include <linux/io.h> >> @@ -1275,6 +1276,7 @@ static const struct of_device_id >> samsung_pinctrl_dt_match[] = { #endif >> {}, >> }; >> +MODULE_DEVICE_TABLE(of, samsung_pinctrl_dt_match); >> >> static const struct dev_pm_ops samsung_pinctrl_pm_ops = { >> SET_LATE_SYSTEM_SLEEP_PM_OPS(samsung_pinctrl_suspend, >> @@ -1296,3 +1298,14 @@ static int __init samsung_pinctrl_drv_register(void) >> return platform_driver_register(&samsung_pinctrl_driver); >> } >> postcore_initcall(samsung_pinctrl_drv_register); >> + >> +static void __exit samsung_pinctrl_drv_unregister(void) >> +{ >> + platform_driver_unregister(&samsung_pinctrl_driver); >> +} >> +module_exit(samsung_pinctrl_drv_unregister); > > Since .suppress_bind_attrs are defined, I find it weird to be able to unload module... Another warning sign... Okay I will apply your comment > >> + >> + >> +MODULE_LICENSE("GPL"); >> +MODULE_AUTHOR("Hyunki Koo <hyunki00.koo@samsung.com>"); > > I cannot find any contributions to this file from you. The author should be the main contributor(s). You need to go through history... > >> +MODULE_DESCRIPTION("Samsung Exynos PINCTRL driver"); > > That's not Exynos but Samsung-generic part... Samsung Exynos/S3C/S5P pinctrl driver. > Okay I will apply your comment _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH] pinctrl: samsung: modularize samsung pinctrl driver 2019-11-26 1:14 ` Hyunki Koo @ 2019-11-26 6:09 ` Krzysztof Kozlowski -1 siblings, 0 replies; 12+ messages in thread From: Krzysztof Kozlowski @ 2019-11-26 6:09 UTC (permalink / raw) To: Hyunki Koo Cc: Tomasz Figa, s.nawrocki, linus.walleij, linux-arm-kernel, linux-samsung-soc, linux-gpio, linux-kernel On Tue, 26 Nov 2019 at 09:14, Hyunki Koo <hyunki00.koo@samsung.com> wrote: > > On Thu, 21 Nov 2019 at 16:38, Krzysztof Kozlowski <krzk@kernel.org> wrote: > > Hi, > > > > Thanks for the patch. Few comments below: > > > > On Thu, 21 Nov 2019 at 15:26, 구현기 <hyunki00.koo@samsung.com> wrote: > >> > >> Enable samsung pinctrl driver to be compiled as modules. > > > > Why? What's the benefit? Are platforms capable of such boot? Pinctrl is needed early - even before mounting rootfs... > > What about module unloading? Is it reasonable? > > Please answer to all this also in commit message. > > > > Sorry to late and Thank you for your comment, I would like to apply GKI on the pinctrl driver > So I would like to cut off dependency from ARCH_EXYNOS. This is driver for Exynos and S3C so why cutting off the dependency? I mean, wait, it is a driver for Exynos so it cannot work on other boards... > I will split into two part, > First, cut off the dependency with ARCH_EXYNOS in arch/arm64/Kconfig.platform. > Second, I will make the pinctrl driver as a module. Then you are doing it in wrong order - this patch makes it as a module but you send it as first one. You did not resolve however my questions about: 1. Will this even work? Will platforms boot? 2. How are you going to handle module unloading since on purpose we added suppress_bind? > > >> > >> Change-Id: I92a9953c92831a316f7f50146898ff19831549ec > > > > This does not belong to Git. > > > >> Signed-off-by: Hyunki Koo <hyunki00.koo@samsung.com> > > > >You "From" name is different than written here in Signed-off-by. They should match and I do not know Korean to be able to tell whether they really match or not :). > >How about using Latin transliteration also in "From" field? > > > >> --- > >> drivers/pinctrl/samsung/Kconfig | 5 +---- > >> drivers/pinctrl/samsung/Makefile | 13 +++++++------ > >> drivers/pinctrl/samsung/pinctrl-exynos-arm.c | 2 ++ > >> drivers/pinctrl/samsung/pinctrl-exynos-arm64.c | 2 ++ > >> drivers/pinctrl/samsung/pinctrl-exynos.c | 2 ++ > >> drivers/pinctrl/samsung/pinctrl-samsung.c | 13 +++++++++++++ > >> 6 files changed, 27 insertions(+), 10 deletions(-) > >> > >> diff --git a/drivers/pinctrl/samsung/Kconfig > >> b/drivers/pinctrl/samsung/Kconfig index 425fadd6c346..25e16984ef23 > >> 100644 > >> --- a/drivers/pinctrl/samsung/Kconfig > >> +++ b/drivers/pinctrl/samsung/Kconfig > >> @@ -3,14 +3,13 @@ > >> # Samsung Pin control drivers > >> # > >> config PINCTRL_SAMSUNG > >> - bool > >> + tristate "Pinctrl driver data for Samsung SoCs" > >> select PINMUX > >> select PINCONF > >> > >> config PINCTRL_EXYNOS > >> bool "Pinctrl driver data for Samsung EXYNOS SoCs" > >> depends on OF && GPIOLIB && (ARCH_EXYNOS || ARCH_S5PV210) > >> - select PINCTRL_SAMSUNG > >> select PINCTRL_EXYNOS_ARM if ARM && (ARCH_EXYNOS || ARCH_S5PV210) > >> select PINCTRL_EXYNOS_ARM64 if ARM64 && ARCH_EXYNOS > >> > >> @@ -25,9 +24,7 @@ config PINCTRL_EXYNOS_ARM64 config PINCTRL_S3C24XX > >> bool "Samsung S3C24XX SoC pinctrl driver" > >> depends on ARCH_S3C24XX && OF > >> - select PINCTRL_SAMSUNG > >> > >> config PINCTRL_S3C64XX > >> bool "Samsung S3C64XX SoC pinctrl driver" > >> depends on ARCH_S3C64XX > >> - select PINCTRL_SAMSUNG > >> diff --git a/drivers/pinctrl/samsung/Makefile > >> b/drivers/pinctrl/samsung/Makefile > >> index ed951df6a112..b3ac01838b8a 100644 > >> --- a/drivers/pinctrl/samsung/Makefile > >> +++ b/drivers/pinctrl/samsung/Makefile > >> @@ -1,9 +1,10 @@ > >> # SPDX-License-Identifier: GPL-2.0 > >> # Samsung pin control drivers > >> > >> -obj-$(CONFIG_PINCTRL_SAMSUNG) += pinctrl-samsung.o > >> -obj-$(CONFIG_PINCTRL_EXYNOS) += pinctrl-exynos.o > >> -obj-$(CONFIG_PINCTRL_EXYNOS_ARM) += pinctrl-exynos-arm.o > >> -obj-$(CONFIG_PINCTRL_EXYNOS_ARM64) += pinctrl-exynos-arm64.o > >> -obj-$(CONFIG_PINCTRL_S3C24XX) += pinctrl-s3c24xx.o > >> -obj-$(CONFIG_PINCTRL_S3C64XX) += pinctrl-s3c64xx.o > >> +obj-$(CONFIG_PINCTRL_SAMSUNG) += pinctrl-samsung-super.o > >> +pinctrl-samsung-super-$(CONFIG_PINCTRL_SAMSUNG) += pinctrl-samsung.o > >> +pinctrl-samsung-super-$(CONFIG_PINCTRL_EXYNOS) += pinctrl-exynos.o > >> +pinctrl-samsung-super-$(CONFIG_PINCTRL_EXYNOS_ARM) += pinctrl-exynos- > >> arm.o > >> +pinctrl-samsung-super-$(CONFIG_PINCTRL_EXYNOS_ARM64) += pinctrl-exynos- > >> arm64.o > >> +pinctrl-samsung-super-$(CONFIG_PINCTRL_S3C24XX) += pinctrl-s3c24xx.o > >> +pinctrl-samsung-super-$(CONFIG_PINCTRL_S3C64XX) += pinctrl-s3c64xx.o > > > > I don't get why you need to rename obj to pinctrl-samsung-super? > > I would like to make pinctrl as a super module. It is many dependency between pinctrl-exynos, pinctr-exynos-arm64 and pinctrl-samsung Might be a stupid question but what is "Super module"? Second, the dependencies are there because this is a integral part of them. I think I miss some bigger picture here because I still do not understand what you want to achieve in the end (why doing this)? Best regards, Krzysztof ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH] pinctrl: samsung: modularize samsung pinctrl driver @ 2019-11-26 6:09 ` Krzysztof Kozlowski 0 siblings, 0 replies; 12+ messages in thread From: Krzysztof Kozlowski @ 2019-11-26 6:09 UTC (permalink / raw) To: Hyunki Koo Cc: linux-samsung-soc, linus.walleij, Tomasz Figa, linux-kernel, linux-gpio, s.nawrocki, linux-arm-kernel On Tue, 26 Nov 2019 at 09:14, Hyunki Koo <hyunki00.koo@samsung.com> wrote: > > On Thu, 21 Nov 2019 at 16:38, Krzysztof Kozlowski <krzk@kernel.org> wrote: > > Hi, > > > > Thanks for the patch. Few comments below: > > > > On Thu, 21 Nov 2019 at 15:26, 구현기 <hyunki00.koo@samsung.com> wrote: > >> > >> Enable samsung pinctrl driver to be compiled as modules. > > > > Why? What's the benefit? Are platforms capable of such boot? Pinctrl is needed early - even before mounting rootfs... > > What about module unloading? Is it reasonable? > > Please answer to all this also in commit message. > > > > Sorry to late and Thank you for your comment, I would like to apply GKI on the pinctrl driver > So I would like to cut off dependency from ARCH_EXYNOS. This is driver for Exynos and S3C so why cutting off the dependency? I mean, wait, it is a driver for Exynos so it cannot work on other boards... > I will split into two part, > First, cut off the dependency with ARCH_EXYNOS in arch/arm64/Kconfig.platform. > Second, I will make the pinctrl driver as a module. Then you are doing it in wrong order - this patch makes it as a module but you send it as first one. You did not resolve however my questions about: 1. Will this even work? Will platforms boot? 2. How are you going to handle module unloading since on purpose we added suppress_bind? > > >> > >> Change-Id: I92a9953c92831a316f7f50146898ff19831549ec > > > > This does not belong to Git. > > > >> Signed-off-by: Hyunki Koo <hyunki00.koo@samsung.com> > > > >You "From" name is different than written here in Signed-off-by. They should match and I do not know Korean to be able to tell whether they really match or not :). > >How about using Latin transliteration also in "From" field? > > > >> --- > >> drivers/pinctrl/samsung/Kconfig | 5 +---- > >> drivers/pinctrl/samsung/Makefile | 13 +++++++------ > >> drivers/pinctrl/samsung/pinctrl-exynos-arm.c | 2 ++ > >> drivers/pinctrl/samsung/pinctrl-exynos-arm64.c | 2 ++ > >> drivers/pinctrl/samsung/pinctrl-exynos.c | 2 ++ > >> drivers/pinctrl/samsung/pinctrl-samsung.c | 13 +++++++++++++ > >> 6 files changed, 27 insertions(+), 10 deletions(-) > >> > >> diff --git a/drivers/pinctrl/samsung/Kconfig > >> b/drivers/pinctrl/samsung/Kconfig index 425fadd6c346..25e16984ef23 > >> 100644 > >> --- a/drivers/pinctrl/samsung/Kconfig > >> +++ b/drivers/pinctrl/samsung/Kconfig > >> @@ -3,14 +3,13 @@ > >> # Samsung Pin control drivers > >> # > >> config PINCTRL_SAMSUNG > >> - bool > >> + tristate "Pinctrl driver data for Samsung SoCs" > >> select PINMUX > >> select PINCONF > >> > >> config PINCTRL_EXYNOS > >> bool "Pinctrl driver data for Samsung EXYNOS SoCs" > >> depends on OF && GPIOLIB && (ARCH_EXYNOS || ARCH_S5PV210) > >> - select PINCTRL_SAMSUNG > >> select PINCTRL_EXYNOS_ARM if ARM && (ARCH_EXYNOS || ARCH_S5PV210) > >> select PINCTRL_EXYNOS_ARM64 if ARM64 && ARCH_EXYNOS > >> > >> @@ -25,9 +24,7 @@ config PINCTRL_EXYNOS_ARM64 config PINCTRL_S3C24XX > >> bool "Samsung S3C24XX SoC pinctrl driver" > >> depends on ARCH_S3C24XX && OF > >> - select PINCTRL_SAMSUNG > >> > >> config PINCTRL_S3C64XX > >> bool "Samsung S3C64XX SoC pinctrl driver" > >> depends on ARCH_S3C64XX > >> - select PINCTRL_SAMSUNG > >> diff --git a/drivers/pinctrl/samsung/Makefile > >> b/drivers/pinctrl/samsung/Makefile > >> index ed951df6a112..b3ac01838b8a 100644 > >> --- a/drivers/pinctrl/samsung/Makefile > >> +++ b/drivers/pinctrl/samsung/Makefile > >> @@ -1,9 +1,10 @@ > >> # SPDX-License-Identifier: GPL-2.0 > >> # Samsung pin control drivers > >> > >> -obj-$(CONFIG_PINCTRL_SAMSUNG) += pinctrl-samsung.o > >> -obj-$(CONFIG_PINCTRL_EXYNOS) += pinctrl-exynos.o > >> -obj-$(CONFIG_PINCTRL_EXYNOS_ARM) += pinctrl-exynos-arm.o > >> -obj-$(CONFIG_PINCTRL_EXYNOS_ARM64) += pinctrl-exynos-arm64.o > >> -obj-$(CONFIG_PINCTRL_S3C24XX) += pinctrl-s3c24xx.o > >> -obj-$(CONFIG_PINCTRL_S3C64XX) += pinctrl-s3c64xx.o > >> +obj-$(CONFIG_PINCTRL_SAMSUNG) += pinctrl-samsung-super.o > >> +pinctrl-samsung-super-$(CONFIG_PINCTRL_SAMSUNG) += pinctrl-samsung.o > >> +pinctrl-samsung-super-$(CONFIG_PINCTRL_EXYNOS) += pinctrl-exynos.o > >> +pinctrl-samsung-super-$(CONFIG_PINCTRL_EXYNOS_ARM) += pinctrl-exynos- > >> arm.o > >> +pinctrl-samsung-super-$(CONFIG_PINCTRL_EXYNOS_ARM64) += pinctrl-exynos- > >> arm64.o > >> +pinctrl-samsung-super-$(CONFIG_PINCTRL_S3C24XX) += pinctrl-s3c24xx.o > >> +pinctrl-samsung-super-$(CONFIG_PINCTRL_S3C64XX) += pinctrl-s3c64xx.o > > > > I don't get why you need to rename obj to pinctrl-samsung-super? > > I would like to make pinctrl as a super module. It is many dependency between pinctrl-exynos, pinctr-exynos-arm64 and pinctrl-samsung Might be a stupid question but what is "Super module"? Second, the dependencies are there because this is a integral part of them. I think I miss some bigger picture here because I still do not understand what you want to achieve in the end (why doing this)? Best regards, Krzysztof _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH] pinctrl: samsung: modularize samsung pinctrl driver 2019-11-26 6:09 ` Krzysztof Kozlowski @ 2019-11-27 1:58 ` Krzysztof Kozlowski -1 siblings, 0 replies; 12+ messages in thread From: Krzysztof Kozlowski @ 2019-11-27 1:58 UTC (permalink / raw) To: Hyunki Koo Cc: Tomasz Figa, s.nawrocki, linus.walleij, linux-arm-kernel, linux-samsung-soc, linux-gpio, linux-kernel On Tue, 26 Nov 2019 at 14:09, Krzysztof Kozlowski <krzk@kernel.org> wrote: > > On Tue, 26 Nov 2019 at 09:14, Hyunki Koo <hyunki00.koo@samsung.com> wrote: > > > > On Thu, 21 Nov 2019 at 16:38, Krzysztof Kozlowski <krzk@kernel.org> wrote: > > > Hi, > > > > > > Thanks for the patch. Few comments below: > > > > > > On Thu, 21 Nov 2019 at 15:26, 구현기 <hyunki00.koo@samsung.com> wrote: > > >> > > >> Enable samsung pinctrl driver to be compiled as modules. > > > > > > Why? What's the benefit? Are platforms capable of such boot? Pinctrl is needed early - even before mounting rootfs... > > > What about module unloading? Is it reasonable? > > > Please answer to all this also in commit message. > > > > > > > Sorry to late and Thank you for your comment, I would like to apply GKI on the pinctrl driver > > So I would like to cut off dependency from ARCH_EXYNOS. > > This is driver for Exynos and S3C so why cutting off the dependency? I > mean, wait, it is a driver for Exynos so it cannot work on other > boards... One more thought about Generic Kernel Image for Android. It implies that vendor stuff will be in modules... but only for out-of-tree code. The Exynos pinctrl driver is already in mainline so moving it into module is not necessary. As for dependency on ARCH_EXYNOS - I do not get why this is a problem. ARCH_EXYNOS is multiplatform ready so you can boot multi_v7... What would be the benefit of removing this dependency? Best regards, Krzysztof ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH] pinctrl: samsung: modularize samsung pinctrl driver @ 2019-11-27 1:58 ` Krzysztof Kozlowski 0 siblings, 0 replies; 12+ messages in thread From: Krzysztof Kozlowski @ 2019-11-27 1:58 UTC (permalink / raw) To: Hyunki Koo Cc: linux-samsung-soc, linus.walleij, Tomasz Figa, linux-kernel, linux-gpio, s.nawrocki, linux-arm-kernel On Tue, 26 Nov 2019 at 14:09, Krzysztof Kozlowski <krzk@kernel.org> wrote: > > On Tue, 26 Nov 2019 at 09:14, Hyunki Koo <hyunki00.koo@samsung.com> wrote: > > > > On Thu, 21 Nov 2019 at 16:38, Krzysztof Kozlowski <krzk@kernel.org> wrote: > > > Hi, > > > > > > Thanks for the patch. Few comments below: > > > > > > On Thu, 21 Nov 2019 at 15:26, 구현기 <hyunki00.koo@samsung.com> wrote: > > >> > > >> Enable samsung pinctrl driver to be compiled as modules. > > > > > > Why? What's the benefit? Are platforms capable of such boot? Pinctrl is needed early - even before mounting rootfs... > > > What about module unloading? Is it reasonable? > > > Please answer to all this also in commit message. > > > > > > > Sorry to late and Thank you for your comment, I would like to apply GKI on the pinctrl driver > > So I would like to cut off dependency from ARCH_EXYNOS. > > This is driver for Exynos and S3C so why cutting off the dependency? I > mean, wait, it is a driver for Exynos so it cannot work on other > boards... One more thought about Generic Kernel Image for Android. It implies that vendor stuff will be in modules... but only for out-of-tree code. The Exynos pinctrl driver is already in mainline so moving it into module is not necessary. As for dependency on ARCH_EXYNOS - I do not get why this is a problem. ARCH_EXYNOS is multiplatform ready so you can boot multi_v7... What would be the benefit of removing this dependency? Best regards, Krzysztof _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH] pinctrl: samsung: modularize samsung pinctrl driver 2019-11-26 1:14 ` Hyunki Koo @ 2019-11-27 7:58 ` Linus Walleij -1 siblings, 0 replies; 12+ messages in thread From: Linus Walleij @ 2019-11-27 7:58 UTC (permalink / raw) To: Hyunki Koo Cc: Krzysztof Kozlowski, Tomasz Figa, Sylwester Nawrocki, Linux ARM, linux-samsung-soc, open list:GPIO SUBSYSTEM, linux-kernel On Tue, Nov 26, 2019 at 2:14 AM Hyunki Koo <hyunki00.koo@samsung.com> wrote: > I would like to apply GKI on the pinctrl driver > So I would like to cut off dependency from ARCH_EXYNOS. If the pins need to be configured for the system to boot that needs to be in the big kernel image anyway. And then it should be bool. Example: to mount the root filesystem on external flash pin configuration needs to happen. There is a slight paradigm shift sometimes: in distribution kernels it might be required that necessary modules are included in an initramfs attached to the kernel. I do not know if we want to encourage that type of configuration for embedded ARM. Yours, Linus Walleij ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH] pinctrl: samsung: modularize samsung pinctrl driver @ 2019-11-27 7:58 ` Linus Walleij 0 siblings, 0 replies; 12+ messages in thread From: Linus Walleij @ 2019-11-27 7:58 UTC (permalink / raw) To: Hyunki Koo Cc: linux-samsung-soc, Tomasz Figa, Krzysztof Kozlowski, linux-kernel, open list:GPIO SUBSYSTEM, Sylwester Nawrocki, Linux ARM On Tue, Nov 26, 2019 at 2:14 AM Hyunki Koo <hyunki00.koo@samsung.com> wrote: > I would like to apply GKI on the pinctrl driver > So I would like to cut off dependency from ARCH_EXYNOS. If the pins need to be configured for the system to boot that needs to be in the big kernel image anyway. And then it should be bool. Example: to mount the root filesystem on external flash pin configuration needs to happen. There is a slight paradigm shift sometimes: in distribution kernels it might be required that necessary modules are included in an initramfs attached to the kernel. I do not know if we want to encourage that type of configuration for embedded ARM. Yours, Linus Walleij _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2019-11-27 7:58 UTC | newest]
Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
[not found] <CGME20191121072643epcas2p452071a503725c7764acf5084d24425b1@epcas2p4.samsung.com>
2019-11-21 7:26 ` [PATCH] pinctrl: samsung: modularize samsung pinctrl driver 구현기
2019-11-21 7:26 ` 구현기
2019-11-21 7:38 ` Krzysztof Kozlowski
2019-11-21 7:38 ` Krzysztof Kozlowski
2019-11-26 1:14 ` Hyunki Koo
2019-11-26 1:14 ` Hyunki Koo
2019-11-26 6:09 ` Krzysztof Kozlowski
2019-11-26 6:09 ` Krzysztof Kozlowski
2019-11-27 1:58 ` Krzysztof Kozlowski
2019-11-27 1:58 ` Krzysztof Kozlowski
2019-11-27 7:58 ` Linus Walleij
2019-11-27 7:58 ` Linus Walleij
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.