[PATCH v2 0/2] Add pinctrl input schmitt support

[PATCH v2 0/2] Add pinctrl input schmitt support

[David Wu]

Some pins need to enable Schmitt triggers which are used
in open loop configurations for noise immunity and closed
loop configurations to implement function generators.

david.wu (2):
  pinctrl: rockchip：Add input schmitt support
  pinctrl: rockchip: Add input schmitt support for rk3328

 drivers/pinctrl/pinctrl-rockchip.c | 96 ++++++++++++++++++++++++++++++++++++++
 1 file changed, 96 insertions(+)

-- 
1.9.1

[PATCH v2 1/2] pinctrl: rockchip：Add input schmitt support

[David Wu]

From: "david.wu" <david.wu-TNX95d0MmH7DzftRWevZcw@public.gmane.org>

To prevent external signal crosstalk, some pins need to
enable input schmitt, like i2c pins, 32k-input pin and so on.

Signed-off-by: david.wu <david.wu-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
---
changes in v2:
 - check the return value (Heiko)

 drivers/pinctrl/pinctrl-rockchip.c | 73 ++++++++++++++++++++++++++++++++++++++
 1 file changed, 73 insertions(+)

diff --git a/drivers/pinctrl/pinctrl-rockchip.c b/drivers/pinctrl/pinctrl-rockchip.c
index a20ce9f..9b8d516 100644
--- a/drivers/pinctrl/pinctrl-rockchip.c
+++ b/drivers/pinctrl/pinctrl-rockchip.c
@@ -308,6 +308,9 @@ struct rockchip_pin_ctrl {
 				    int *reg, u8 *bit);
 	void	(*iomux_recalc)(u8 bank_num, int pin, int *reg,
 				u8 *bit, int *mask);
+	int	(*schmitt_calc_reg)(struct rockchip_pin_bank *bank,
+				    int pin_num, struct regmap **regmap,
+				    int *reg, u8 *bit);
 };
 
 struct rockchip_pin_config {
@@ -1355,6 +1358,57 @@ static int rockchip_set_pull(struct rockchip_pin_bank *bank,
 	return ret;
 }
 
+static int rockchip_get_schmitt(struct rockchip_pin_bank *bank, int pin_num)
+{
+	struct rockchip_pinctrl *info = bank->drvdata;
+	struct rockchip_pin_ctrl *ctrl = info->ctrl;
+	struct regmap *regmap;
+	int reg, ret;
+	u8 bit;
+	u32 data;
+
+	ret = ctrl->schmitt_calc_reg(bank, pin_num, &regmap, &reg, &bit);
+	if (ret)
+		return ret;
+
+	ret = regmap_read(regmap, reg, &data);
+	if (ret)
+		return ret;
+
+	data >>= bit;
+	return data & 0x1;
+}
+
+static int rockchip_set_schmitt(struct rockchip_pin_bank *bank,
+				int pin_num, int enable)
+{
+	struct rockchip_pinctrl *info = bank->drvdata;
+	struct rockchip_pin_ctrl *ctrl = info->ctrl;
+	struct regmap *regmap;
+	int reg, ret;
+	unsigned long flags;
+	u8 bit;
+	u32 data, rmask;
+
+	dev_dbg(info->dev, "setting input schmitt of GPIO%d-%d to %d\n",
+		bank->bank_num, pin_num, enable);
+
+	ret = ctrl->schmitt_calc_reg(bank, pin_num, &regmap, &reg, &bit);
+	if (ret)
+		return ret;
+
+	spin_lock_irqsave(&bank->slock, flags);
+
+	/* enable the write to the equivalent lower bits */
+	data = BIT(bit + 16) | (enable << bit);
+	rmask = BIT(bit + 16) | BIT(bit);
+
+	ret = regmap_update_bits(regmap, reg, rmask, data);
+	spin_unlock_irqrestore(&bank->slock, flags);
+
+	return ret;
+}
+
 /*
  * Pinmux_ops handling
  */
@@ -1574,6 +1628,15 @@ static int rockchip_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin,
 			if (rc < 0)
 				return rc;
 			break;
+		case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
+			if (!info->ctrl->schmitt_calc_reg)
+				return -ENOTSUPP;
+
+			rc = rockchip_set_schmitt(bank,
+						  pin - bank->pin_base, arg);
+			if (rc < 0)
+				return rc;
+			break;
 		default:
 			return -ENOTSUPP;
 			break;
@@ -1634,6 +1697,16 @@ static int rockchip_pinconf_get(struct pinctrl_dev *pctldev, unsigned int pin,
 
 		arg = rc;
 		break;
+	case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
+		if (!info->ctrl->schmitt_calc_reg)
+			return -ENOTSUPP;
+
+		rc = rockchip_get_schmitt(bank, pin - bank->pin_base);
+		if (rc < 0)
+			return rc;
+
+		arg = rc;
+		break;
 	default:
 		return -ENOTSUPP;
 		break;
-- 
1.9.1

[PATCH v2 1/2] pinctrl: rockchip：Add input schmitt support

[David Wu]

From: "david.wu" <david.wu@rock-chips.com>

To prevent external signal crosstalk, some pins need to
enable input schmitt, like i2c pins, 32k-input pin and so on.

Signed-off-by: david.wu <david.wu@rock-chips.com>
---
changes in v2:
 - check the return value (Heiko)

 drivers/pinctrl/pinctrl-rockchip.c | 73 ++++++++++++++++++++++++++++++++++++++
 1 file changed, 73 insertions(+)

diff --git a/drivers/pinctrl/pinctrl-rockchip.c b/drivers/pinctrl/pinctrl-rockchip.c
index a20ce9f..9b8d516 100644
--- a/drivers/pinctrl/pinctrl-rockchip.c
+++ b/drivers/pinctrl/pinctrl-rockchip.c
@@ -308,6 +308,9 @@ struct rockchip_pin_ctrl {
 				    int *reg, u8 *bit);
 	void	(*iomux_recalc)(u8 bank_num, int pin, int *reg,
 				u8 *bit, int *mask);
+	int	(*schmitt_calc_reg)(struct rockchip_pin_bank *bank,
+				    int pin_num, struct regmap **regmap,
+				    int *reg, u8 *bit);
 };
 
 struct rockchip_pin_config {
@@ -1355,6 +1358,57 @@ static int rockchip_set_pull(struct rockchip_pin_bank *bank,
 	return ret;
 }
 
+static int rockchip_get_schmitt(struct rockchip_pin_bank *bank, int pin_num)
+{
+	struct rockchip_pinctrl *info = bank->drvdata;
+	struct rockchip_pin_ctrl *ctrl = info->ctrl;
+	struct regmap *regmap;
+	int reg, ret;
+	u8 bit;
+	u32 data;
+
+	ret = ctrl->schmitt_calc_reg(bank, pin_num, &regmap, &reg, &bit);
+	if (ret)
+		return ret;
+
+	ret = regmap_read(regmap, reg, &data);
+	if (ret)
+		return ret;
+
+	data >>= bit;
+	return data & 0x1;
+}
+
+static int rockchip_set_schmitt(struct rockchip_pin_bank *bank,
+				int pin_num, int enable)
+{
+	struct rockchip_pinctrl *info = bank->drvdata;
+	struct rockchip_pin_ctrl *ctrl = info->ctrl;
+	struct regmap *regmap;
+	int reg, ret;
+	unsigned long flags;
+	u8 bit;
+	u32 data, rmask;
+
+	dev_dbg(info->dev, "setting input schmitt of GPIO%d-%d to %d\n",
+		bank->bank_num, pin_num, enable);
+
+	ret = ctrl->schmitt_calc_reg(bank, pin_num, &regmap, &reg, &bit);
+	if (ret)
+		return ret;
+
+	spin_lock_irqsave(&bank->slock, flags);
+
+	/* enable the write to the equivalent lower bits */
+	data = BIT(bit + 16) | (enable << bit);
+	rmask = BIT(bit + 16) | BIT(bit);
+
+	ret = regmap_update_bits(regmap, reg, rmask, data);
+	spin_unlock_irqrestore(&bank->slock, flags);
+
+	return ret;
+}
+
 /*
  * Pinmux_ops handling
  */
@@ -1574,6 +1628,15 @@ static int rockchip_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin,
 			if (rc < 0)
 				return rc;
 			break;
+		case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
+			if (!info->ctrl->schmitt_calc_reg)
+				return -ENOTSUPP;
+
+			rc = rockchip_set_schmitt(bank,
+						  pin - bank->pin_base, arg);
+			if (rc < 0)
+				return rc;
+			break;
 		default:
 			return -ENOTSUPP;
 			break;
@@ -1634,6 +1697,16 @@ static int rockchip_pinconf_get(struct pinctrl_dev *pctldev, unsigned int pin,
 
 		arg = rc;
 		break;
+	case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
+		if (!info->ctrl->schmitt_calc_reg)
+			return -ENOTSUPP;
+
+		rc = rockchip_get_schmitt(bank, pin - bank->pin_base);
+		if (rc < 0)
+			return rc;
+
+		arg = rc;
+		break;
 	default:
 		return -ENOTSUPP;
 		break;
-- 
1.9.1

[PATCH v2 2/2] pinctrl: rockchip: Add input schmitt support for rk3328

[David Wu]

From: "david.wu" <david.wu-TNX95d0MmH7DzftRWevZcw@public.gmane.org>

Signed-off-by: david.wu <david.wu-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
Reviewed-by: Heiko Stuebner <heiko-4mtYJXux2i+zQB+pC5nmwQ@public.gmane.org>
---
 drivers/pinctrl/pinctrl-rockchip.c | 23 +++++++++++++++++++++++
 1 file changed, 23 insertions(+)

diff --git a/drivers/pinctrl/pinctrl-rockchip.c b/drivers/pinctrl/pinctrl-rockchip.c
index 9b8d516..91b5051 100644
--- a/drivers/pinctrl/pinctrl-rockchip.c
+++ b/drivers/pinctrl/pinctrl-rockchip.c
@@ -1358,6 +1358,28 @@ static int rockchip_set_pull(struct rockchip_pin_bank *bank,
 	return ret;
 }
 
+#define RK3328_SCHMITT_BITS_PER_PIN		1
+#define RK3328_SCHMITT_PINS_PER_REG		16
+#define RK3328_SCHMITT_BANK_STRIDE		8
+#define RK3328_SCHMITT_GRF_OFFSET		0x380
+
+static int rk3328_calc_schmitt_reg_and_bit(struct rockchip_pin_bank *bank,
+					   int pin_num,
+					   struct regmap **regmap,
+					   int *reg, u8 *bit)
+{
+	struct rockchip_pinctrl *info = bank->drvdata;
+
+	*regmap = info->regmap_base;
+	*reg = RK3328_SCHMITT_GRF_OFFSET;
+
+	*reg += bank->bank_num * RK3328_SCHMITT_BANK_STRIDE;
+	*reg += ((pin_num / RK3328_SCHMITT_PINS_PER_REG) * 4);
+	*bit = pin_num % RK3328_SCHMITT_PINS_PER_REG;
+
+	return 0;
+}
+
 static int rockchip_get_schmitt(struct rockchip_pin_bank *bank, int pin_num)
 {
 	struct rockchip_pinctrl *info = bank->drvdata;
@@ -2861,6 +2883,7 @@ static int rockchip_pinctrl_probe(struct platform_device *pdev)
 		.pull_calc_reg		= rk3228_calc_pull_reg_and_bit,
 		.drv_calc_reg		= rk3228_calc_drv_reg_and_bit,
 		.iomux_recalc		= rk3328_recalc_mux,
+		.schmitt_calc_reg	= rk3328_calc_schmitt_reg_and_bit,
 };
 
 static struct rockchip_pin_bank rk3368_pin_banks[] = {
-- 
1.9.1

[PATCH v2 2/2] pinctrl: rockchip: Add input schmitt support for rk3328

[David Wu]

From: "david.wu" <david.wu@rock-chips.com>

Signed-off-by: david.wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
---
 drivers/pinctrl/pinctrl-rockchip.c | 23 +++++++++++++++++++++++
 1 file changed, 23 insertions(+)

diff --git a/drivers/pinctrl/pinctrl-rockchip.c b/drivers/pinctrl/pinctrl-rockchip.c
index 9b8d516..91b5051 100644
--- a/drivers/pinctrl/pinctrl-rockchip.c
+++ b/drivers/pinctrl/pinctrl-rockchip.c
@@ -1358,6 +1358,28 @@ static int rockchip_set_pull(struct rockchip_pin_bank *bank,
 	return ret;
 }
 
+#define RK3328_SCHMITT_BITS_PER_PIN		1
+#define RK3328_SCHMITT_PINS_PER_REG		16
+#define RK3328_SCHMITT_BANK_STRIDE		8
+#define RK3328_SCHMITT_GRF_OFFSET		0x380
+
+static int rk3328_calc_schmitt_reg_and_bit(struct rockchip_pin_bank *bank,
+					   int pin_num,
+					   struct regmap **regmap,
+					   int *reg, u8 *bit)
+{
+	struct rockchip_pinctrl *info = bank->drvdata;
+
+	*regmap = info->regmap_base;
+	*reg = RK3328_SCHMITT_GRF_OFFSET;
+
+	*reg += bank->bank_num * RK3328_SCHMITT_BANK_STRIDE;
+	*reg += ((pin_num / RK3328_SCHMITT_PINS_PER_REG) * 4);
+	*bit = pin_num % RK3328_SCHMITT_PINS_PER_REG;
+
+	return 0;
+}
+
 static int rockchip_get_schmitt(struct rockchip_pin_bank *bank, int pin_num)
 {
 	struct rockchip_pinctrl *info = bank->drvdata;
@@ -2861,6 +2883,7 @@ static int rockchip_pinctrl_probe(struct platform_device *pdev)
 		.pull_calc_reg		= rk3228_calc_pull_reg_and_bit,
 		.drv_calc_reg		= rk3228_calc_drv_reg_and_bit,
 		.iomux_recalc		= rk3328_recalc_mux,
+		.schmitt_calc_reg	= rk3328_calc_schmitt_reg_and_bit,
 };
 
 static struct rockchip_pin_bank rk3368_pin_banks[] = {
-- 
1.9.1

Re: [PATCH v2 1/2] pinctrl: rockchip：Add input schmitt support

[Kever Yang]

Hi David,

On 03/02/2017 03:11 PM, David Wu wrote:
> From: "david.wu" <david.wu-TNX95d0MmH7DzftRWevZcw@public.gmane.org>

You do not need to add this when you send mail for yourself,
it's need when you send mail for others.

>
> To prevent external signal crosstalk, some pins need to
> enable input schmitt, like i2c pins, 32k-input pin and so on.
>
> Signed-off-by: david.wu <david.wu-TNX95d0MmH7DzftRWevZcw@public.gmane.org>

Better to use "David Wu" for full name, you can correct this in your 
gitconfig file.

Thanks,
- Kever
> ---
> changes in v2:
>   - check the return value (Heiko)
>
>   drivers/pinctrl/pinctrl-rockchip.c | 73 ++++++++++++++++++++++++++++++++++++++
>   1 file changed, 73 insertions(+)
>
> diff --git a/drivers/pinctrl/pinctrl-rockchip.c b/drivers/pinctrl/pinctrl-rockchip.c
> index a20ce9f..9b8d516 100644
> --- a/drivers/pinctrl/pinctrl-rockchip.c
> +++ b/drivers/pinctrl/pinctrl-rockchip.c
> @@ -308,6 +308,9 @@ struct rockchip_pin_ctrl {
>   				    int *reg, u8 *bit);
>   	void	(*iomux_recalc)(u8 bank_num, int pin, int *reg,
>   				u8 *bit, int *mask);
> +	int	(*schmitt_calc_reg)(struct rockchip_pin_bank *bank,
> +				    int pin_num, struct regmap **regmap,
> +				    int *reg, u8 *bit);
>   };
>   
>   struct rockchip_pin_config {
> @@ -1355,6 +1358,57 @@ static int rockchip_set_pull(struct rockchip_pin_bank *bank,
>   	return ret;
>   }
>   
> +static int rockchip_get_schmitt(struct rockchip_pin_bank *bank, int pin_num)
> +{
> +	struct rockchip_pinctrl *info = bank->drvdata;
> +	struct rockchip_pin_ctrl *ctrl = info->ctrl;
> +	struct regmap *regmap;
> +	int reg, ret;
> +	u8 bit;
> +	u32 data;
> +
> +	ret = ctrl->schmitt_calc_reg(bank, pin_num, &regmap, &reg, &bit);
> +	if (ret)
> +		return ret;
> +
> +	ret = regmap_read(regmap, reg, &data);
> +	if (ret)
> +		return ret;
> +
> +	data >>= bit;
> +	return data & 0x1;
> +}
> +
> +static int rockchip_set_schmitt(struct rockchip_pin_bank *bank,
> +				int pin_num, int enable)
> +{
> +	struct rockchip_pinctrl *info = bank->drvdata;
> +	struct rockchip_pin_ctrl *ctrl = info->ctrl;
> +	struct regmap *regmap;
> +	int reg, ret;
> +	unsigned long flags;
> +	u8 bit;
> +	u32 data, rmask;
> +
> +	dev_dbg(info->dev, "setting input schmitt of GPIO%d-%d to %d\n",
> +		bank->bank_num, pin_num, enable);
> +
> +	ret = ctrl->schmitt_calc_reg(bank, pin_num, &regmap, &reg, &bit);
> +	if (ret)
> +		return ret;
> +
> +	spin_lock_irqsave(&bank->slock, flags);
> +
> +	/* enable the write to the equivalent lower bits */
> +	data = BIT(bit + 16) | (enable << bit);
> +	rmask = BIT(bit + 16) | BIT(bit);
> +
> +	ret = regmap_update_bits(regmap, reg, rmask, data);
> +	spin_unlock_irqrestore(&bank->slock, flags);
> +
> +	return ret;
> +}
> +
>   /*
>    * Pinmux_ops handling
>    */
> @@ -1574,6 +1628,15 @@ static int rockchip_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin,
>   			if (rc < 0)
>   				return rc;
>   			break;
> +		case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
> +			if (!info->ctrl->schmitt_calc_reg)
> +				return -ENOTSUPP;
> +
> +			rc = rockchip_set_schmitt(bank,
> +						  pin - bank->pin_base, arg);
> +			if (rc < 0)
> +				return rc;
> +			break;
>   		default:
>   			return -ENOTSUPP;
>   			break;
> @@ -1634,6 +1697,16 @@ static int rockchip_pinconf_get(struct pinctrl_dev *pctldev, unsigned int pin,
>   
>   		arg = rc;
>   		break;
> +	case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
> +		if (!info->ctrl->schmitt_calc_reg)
> +			return -ENOTSUPP;
> +
> +		rc = rockchip_get_schmitt(bank, pin - bank->pin_base);
> +		if (rc < 0)
> +			return rc;
> +
> +		arg = rc;
> +		break;
>   	default:
>   		return -ENOTSUPP;
>   		break;

Re: [PATCH v2 1/2] pinctrl: rockchip：Add input schmitt support

[Kever Yang]

Hi David,

On 03/02/2017 03:11 PM, David Wu wrote:
> From: "david.wu" <david.wu@rock-chips.com>

You do not need to add this when you send mail for yourself,
it's need when you send mail for others.

>
> To prevent external signal crosstalk, some pins need to
> enable input schmitt, like i2c pins, 32k-input pin and so on.
>
> Signed-off-by: david.wu <david.wu@rock-chips.com>

Better to use "David Wu" for full name, you can correct this in your 
gitconfig file.

Thanks,
- Kever
> ---
> changes in v2:
>   - check the return value (Heiko)
>
>   drivers/pinctrl/pinctrl-rockchip.c | 73 ++++++++++++++++++++++++++++++++++++++
>   1 file changed, 73 insertions(+)
>
> diff --git a/drivers/pinctrl/pinctrl-rockchip.c b/drivers/pinctrl/pinctrl-rockchip.c
> index a20ce9f..9b8d516 100644
> --- a/drivers/pinctrl/pinctrl-rockchip.c
> +++ b/drivers/pinctrl/pinctrl-rockchip.c
> @@ -308,6 +308,9 @@ struct rockchip_pin_ctrl {
>   				    int *reg, u8 *bit);
>   	void	(*iomux_recalc)(u8 bank_num, int pin, int *reg,
>   				u8 *bit, int *mask);
> +	int	(*schmitt_calc_reg)(struct rockchip_pin_bank *bank,
> +				    int pin_num, struct regmap **regmap,
> +				    int *reg, u8 *bit);
>   };
>   
>   struct rockchip_pin_config {
> @@ -1355,6 +1358,57 @@ static int rockchip_set_pull(struct rockchip_pin_bank *bank,
>   	return ret;
>   }
>   
> +static int rockchip_get_schmitt(struct rockchip_pin_bank *bank, int pin_num)
> +{
> +	struct rockchip_pinctrl *info = bank->drvdata;
> +	struct rockchip_pin_ctrl *ctrl = info->ctrl;
> +	struct regmap *regmap;
> +	int reg, ret;
> +	u8 bit;
> +	u32 data;
> +
> +	ret = ctrl->schmitt_calc_reg(bank, pin_num, &regmap, &reg, &bit);
> +	if (ret)
> +		return ret;
> +
> +	ret = regmap_read(regmap, reg, &data);
> +	if (ret)
> +		return ret;
> +
> +	data >>= bit;
> +	return data & 0x1;
> +}
> +
> +static int rockchip_set_schmitt(struct rockchip_pin_bank *bank,
> +				int pin_num, int enable)
> +{
> +	struct rockchip_pinctrl *info = bank->drvdata;
> +	struct rockchip_pin_ctrl *ctrl = info->ctrl;
> +	struct regmap *regmap;
> +	int reg, ret;
> +	unsigned long flags;
> +	u8 bit;
> +	u32 data, rmask;
> +
> +	dev_dbg(info->dev, "setting input schmitt of GPIO%d-%d to %d\n",
> +		bank->bank_num, pin_num, enable);
> +
> +	ret = ctrl->schmitt_calc_reg(bank, pin_num, &regmap, &reg, &bit);
> +	if (ret)
> +		return ret;
> +
> +	spin_lock_irqsave(&bank->slock, flags);
> +
> +	/* enable the write to the equivalent lower bits */
> +	data = BIT(bit + 16) | (enable << bit);
> +	rmask = BIT(bit + 16) | BIT(bit);
> +
> +	ret = regmap_update_bits(regmap, reg, rmask, data);
> +	spin_unlock_irqrestore(&bank->slock, flags);
> +
> +	return ret;
> +}
> +
>   /*
>    * Pinmux_ops handling
>    */
> @@ -1574,6 +1628,15 @@ static int rockchip_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin,
>   			if (rc < 0)
>   				return rc;
>   			break;
> +		case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
> +			if (!info->ctrl->schmitt_calc_reg)
> +				return -ENOTSUPP;
> +
> +			rc = rockchip_set_schmitt(bank,
> +						  pin - bank->pin_base, arg);
> +			if (rc < 0)
> +				return rc;
> +			break;
>   		default:
>   			return -ENOTSUPP;
>   			break;
> @@ -1634,6 +1697,16 @@ static int rockchip_pinconf_get(struct pinctrl_dev *pctldev, unsigned int pin,
>   
>   		arg = rc;
>   		break;
> +	case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
> +		if (!info->ctrl->schmitt_calc_reg)
> +			return -ENOTSUPP;
> +
> +		rc = rockchip_get_schmitt(bank, pin - bank->pin_base);
> +		if (rc < 0)
> +			return rc;
> +
> +		arg = rc;
> +		break;
>   	default:
>   		return -ENOTSUPP;
>   		break;

Re: [PATCH v2 2/2] pinctrl: rockchip: Add input schmitt support for rk3328

[Linus Walleij]

On Thu, Mar 2, 2017 at 8:11 AM, David Wu <david.wu-TNX95d0MmH7DzftRWevZcw@public.gmane.org> wrote:

> From: "david.wu" <david.wu-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
>
> Signed-off-by: david.wu <david.wu-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
> Reviewed-by: Heiko Stuebner <heiko-4mtYJXux2i+zQB+pC5nmwQ@public.gmane.org>

Patch applied.

Yours,
Linus Walleij

Re: [PATCH v2 2/2] pinctrl: rockchip: Add input schmitt support for rk3328

[Linus Walleij]

On Thu, Mar 2, 2017 at 8:11 AM, David Wu <david.wu@rock-chips.com> wrote:

> From: "david.wu" <david.wu@rock-chips.com>
>
> Signed-off-by: david.wu <david.wu@rock-chips.com>
> Reviewed-by: Heiko Stuebner <heiko@sntech.de>

Patch applied.

Yours,
Linus Walleij

Re: [PATCH v2 1/2] pinctrl: rockchip：Add input schmitt support

[Linus Walleij]

On Thu, Mar 2, 2017 at 8:11 AM, David Wu <david.wu-TNX95d0MmH7DzftRWevZcw@public.gmane.org> wrote:

> From: "david.wu" <david.wu-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
>
> To prevent external signal crosstalk, some pins need to
> enable input schmitt, like i2c pins, 32k-input pin and so on.
>
> Signed-off-by: david.wu <david.wu-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
> ---
> changes in v2:
>  - check the return value (Heiko)

Patch applied.

I assume Heiko's ACK on this too.

Yours,
Linus Walleij

Re: [PATCH v2 1/2] pinctrl: rockchip：Add input schmitt support

[Linus Walleij]

On Thu, Mar 2, 2017 at 8:11 AM, David Wu <david.wu@rock-chips.com> wrote:

> From: "david.wu" <david.wu@rock-chips.com>
>
> To prevent external signal crosstalk, some pins need to
> enable input schmitt, like i2c pins, 32k-input pin and so on.
>
> Signed-off-by: david.wu <david.wu@rock-chips.com>
> ---
> changes in v2:
>  - check the return value (Heiko)

Patch applied.

I assume Heiko's ACK on this too.

Yours,
Linus Walleij

Re: [PATCH v2 1/2] pinctrl: rockchip：Add input schmitt support

[Linus Walleij]

On Thu, Mar 2, 2017 at 9:30 AM, Kever Yang <kever.yang@rock-chips.com> wrote:

>> Signed-off-by: david.wu <david.wu@rock-chips.com>
>
> Better to use "David Wu" for full name, you can correct this in your
> gitconfig file.

Yeah please do that, I fix it up manually every time.

Yours,
Linus Walleij