* [PATCH 0/3] Support for USB DRD Phy driver for NS2
@ 2016-11-30 5:55 ` Raviteja Garimella
0 siblings, 0 replies; 20+ messages in thread
From: Raviteja Garimella @ 2016-11-30 5:55 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Kishon Vijay Abraham I, Ray Jui,
Scott Branden, Jon Mason, Catalin Marinas, Will Deacon
Cc: devicetree, linux-kernel, bcm-kernel-feedback-list, linux-arm-kernel
This patch adds support for USB Dual Role Device Phy for Broadcom
Northstar2 SoC. Apart from the new phy driver, this patchset contains
changes to Kconfig, Makefile, and Device tree files.
This patchset is tested on Broadcom NS2 BCM958712K reference board.
Repo: https://github.com/Broadcom/arm64-linux.git
Branch: ns2_drdphy
Raviteja Garimella (3):
Add DT bindings documentation for NS2 USB DRD phy
Broadcom USB DRD Phy driver for Northstar2
DT nodes for Broadcom Northstar2 USB DRD Phy
.../devicetree/bindings/phy/brcm,ns2-drd-phy.txt | 40 ++
arch/arm64/boot/dts/broadcom/ns2.dtsi | 14 +
drivers/phy/Kconfig | 13 +
drivers/phy/Makefile | 1 +
drivers/phy/phy-bcm-ns2-usbdrd.c | 587 +++++++++++++++++++++
5 files changed, 655 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt
create mode 100644 drivers/phy/phy-bcm-ns2-usbdrd.c
--
2.1.0
^ permalink raw reply [flat|nested] 20+ messages in thread
* [PATCH 0/3] Support for USB DRD Phy driver for NS2
@ 2016-11-30 5:55 ` Raviteja Garimella
0 siblings, 0 replies; 20+ messages in thread
From: Raviteja Garimella @ 2016-11-30 5:55 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Kishon Vijay Abraham I, Ray Jui,
Scott Branden, Jon Mason, Catalin Marinas, Will Deacon
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
bcm-kernel-feedback-list-dY08KVG/lbpWk0Htik3J/w,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
This patch adds support for USB Dual Role Device Phy for Broadcom
Northstar2 SoC. Apart from the new phy driver, this patchset contains
changes to Kconfig, Makefile, and Device tree files.
This patchset is tested on Broadcom NS2 BCM958712K reference board.
Repo: https://github.com/Broadcom/arm64-linux.git
Branch: ns2_drdphy
Raviteja Garimella (3):
Add DT bindings documentation for NS2 USB DRD phy
Broadcom USB DRD Phy driver for Northstar2
DT nodes for Broadcom Northstar2 USB DRD Phy
.../devicetree/bindings/phy/brcm,ns2-drd-phy.txt | 40 ++
arch/arm64/boot/dts/broadcom/ns2.dtsi | 14 +
drivers/phy/Kconfig | 13 +
drivers/phy/Makefile | 1 +
drivers/phy/phy-bcm-ns2-usbdrd.c | 587 +++++++++++++++++++++
5 files changed, 655 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt
create mode 100644 drivers/phy/phy-bcm-ns2-usbdrd.c
--
2.1.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 20+ messages in thread
* [PATCH 0/3] Support for USB DRD Phy driver for NS2
@ 2016-11-30 5:55 ` Raviteja Garimella
0 siblings, 0 replies; 20+ messages in thread
From: Raviteja Garimella @ 2016-11-30 5:55 UTC (permalink / raw)
To: linux-arm-kernel
This patch adds support for USB Dual Role Device Phy for Broadcom
Northstar2 SoC. Apart from the new phy driver, this patchset contains
changes to Kconfig, Makefile, and Device tree files.
This patchset is tested on Broadcom NS2 BCM958712K reference board.
Repo: https://github.com/Broadcom/arm64-linux.git
Branch: ns2_drdphy
Raviteja Garimella (3):
Add DT bindings documentation for NS2 USB DRD phy
Broadcom USB DRD Phy driver for Northstar2
DT nodes for Broadcom Northstar2 USB DRD Phy
.../devicetree/bindings/phy/brcm,ns2-drd-phy.txt | 40 ++
arch/arm64/boot/dts/broadcom/ns2.dtsi | 14 +
drivers/phy/Kconfig | 13 +
drivers/phy/Makefile | 1 +
drivers/phy/phy-bcm-ns2-usbdrd.c | 587 +++++++++++++++++++++
5 files changed, 655 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt
create mode 100644 drivers/phy/phy-bcm-ns2-usbdrd.c
--
2.1.0
^ permalink raw reply [flat|nested] 20+ messages in thread
* [PATCH 1/3] Add DT bindings documentation for NS2 USB DRD phy
@ 2016-11-30 5:55 ` Raviteja Garimella
0 siblings, 0 replies; 20+ messages in thread
From: Raviteja Garimella @ 2016-11-30 5:55 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Kishon Vijay Abraham I, Ray Jui,
Scott Branden, Jon Mason, Catalin Marinas, Will Deacon
Cc: devicetree, linux-kernel, bcm-kernel-feedback-list, linux-arm-kernel
This patch adds documentation for NS2 DRD Phy driver DT bindings
Signed-off-by: Raviteja Garimella <raviteja.garimella@broadcom.com>
---
.../devicetree/bindings/phy/brcm,ns2-drd-phy.txt | 40 ++++++++++++++++++++++
1 file changed, 40 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt
diff --git a/Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt b/Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt
new file mode 100644
index 0000000..5857f99
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt
@@ -0,0 +1,40 @@
+BROADCOM NORTHSTAR2 USB2 (DUAL ROLE DEVICE) PHY
+
+Required properties:
+ - compatible: brcm,ns2-drd-phy
+ - reg: offset and length of the NS2 PHY related registers.
+ - reg-names
+ The below registers must be provided.
+ icfg - for DRD ICFG configurations
+ rst-ctrl - for DRD IDM reset
+ crmu-ctrl - for CRMU core vdd, PHY and PHY PLL reset
+ usb2-strap - for port over current polarity reversal
+ - #phy-cells: Must be 0. No args required.
+ - vbus-gpios: vbus gpio binding
+ - id-gpios: id gpio binding
+
+Refer to phy/phy-bindings.txt for the generic PHY binding properties
+
+Example:
+ gpio_g: gpio@660a0000 {
+ compatible = "brcm,iproc-gpio";
+ reg = <0x660a0000 0x50>;
+ ngpios = <32>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ interrupts = <GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ usbdrd_phy: phy@66000960 {
+ #phy-cells = <0>;
+ compatible = "brcm,ns2-drd-phy";
+ reg = <0x66000960 0x24>,
+ <0x67012800 0x4>,
+ <0x6501d148 0x4>,
+ <0x664d0700 0x4>;
+ reg-names = "icfg", "rst-ctrl",
+ "crmu-ctrl", "usb2-strap";
+ id-gpios = <&gpio_g 30 0>;
+ vbus-gpios = <&gpio_g 31 0>;
+ };
--
2.1.0
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH 1/3] Add DT bindings documentation for NS2 USB DRD phy
@ 2016-11-30 5:55 ` Raviteja Garimella
0 siblings, 0 replies; 20+ messages in thread
From: Raviteja Garimella @ 2016-11-30 5:55 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Kishon Vijay Abraham I, Ray Jui,
Scott Branden, Jon Mason, Catalin Marinas, Will Deacon
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
bcm-kernel-feedback-list-dY08KVG/lbpWk0Htik3J/w,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
This patch adds documentation for NS2 DRD Phy driver DT bindings
Signed-off-by: Raviteja Garimella <raviteja.garimella-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>
---
.../devicetree/bindings/phy/brcm,ns2-drd-phy.txt | 40 ++++++++++++++++++++++
1 file changed, 40 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt
diff --git a/Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt b/Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt
new file mode 100644
index 0000000..5857f99
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt
@@ -0,0 +1,40 @@
+BROADCOM NORTHSTAR2 USB2 (DUAL ROLE DEVICE) PHY
+
+Required properties:
+ - compatible: brcm,ns2-drd-phy
+ - reg: offset and length of the NS2 PHY related registers.
+ - reg-names
+ The below registers must be provided.
+ icfg - for DRD ICFG configurations
+ rst-ctrl - for DRD IDM reset
+ crmu-ctrl - for CRMU core vdd, PHY and PHY PLL reset
+ usb2-strap - for port over current polarity reversal
+ - #phy-cells: Must be 0. No args required.
+ - vbus-gpios: vbus gpio binding
+ - id-gpios: id gpio binding
+
+Refer to phy/phy-bindings.txt for the generic PHY binding properties
+
+Example:
+ gpio_g: gpio@660a0000 {
+ compatible = "brcm,iproc-gpio";
+ reg = <0x660a0000 0x50>;
+ ngpios = <32>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ interrupts = <GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ usbdrd_phy: phy@66000960 {
+ #phy-cells = <0>;
+ compatible = "brcm,ns2-drd-phy";
+ reg = <0x66000960 0x24>,
+ <0x67012800 0x4>,
+ <0x6501d148 0x4>,
+ <0x664d0700 0x4>;
+ reg-names = "icfg", "rst-ctrl",
+ "crmu-ctrl", "usb2-strap";
+ id-gpios = <&gpio_g 30 0>;
+ vbus-gpios = <&gpio_g 31 0>;
+ };
--
2.1.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH 1/3] Add DT bindings documentation for NS2 USB DRD phy
@ 2016-11-30 5:55 ` Raviteja Garimella
0 siblings, 0 replies; 20+ messages in thread
From: Raviteja Garimella @ 2016-11-30 5:55 UTC (permalink / raw)
To: linux-arm-kernel
This patch adds documentation for NS2 DRD Phy driver DT bindings
Signed-off-by: Raviteja Garimella <raviteja.garimella@broadcom.com>
---
.../devicetree/bindings/phy/brcm,ns2-drd-phy.txt | 40 ++++++++++++++++++++++
1 file changed, 40 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt
diff --git a/Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt b/Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt
new file mode 100644
index 0000000..5857f99
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt
@@ -0,0 +1,40 @@
+BROADCOM NORTHSTAR2 USB2 (DUAL ROLE DEVICE) PHY
+
+Required properties:
+ - compatible: brcm,ns2-drd-phy
+ - reg: offset and length of the NS2 PHY related registers.
+ - reg-names
+ The below registers must be provided.
+ icfg - for DRD ICFG configurations
+ rst-ctrl - for DRD IDM reset
+ crmu-ctrl - for CRMU core vdd, PHY and PHY PLL reset
+ usb2-strap - for port over current polarity reversal
+ - #phy-cells: Must be 0. No args required.
+ - vbus-gpios: vbus gpio binding
+ - id-gpios: id gpio binding
+
+Refer to phy/phy-bindings.txt for the generic PHY binding properties
+
+Example:
+ gpio_g: gpio at 660a0000 {
+ compatible = "brcm,iproc-gpio";
+ reg = <0x660a0000 0x50>;
+ ngpios = <32>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ interrupts = <GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ usbdrd_phy: phy at 66000960 {
+ #phy-cells = <0>;
+ compatible = "brcm,ns2-drd-phy";
+ reg = <0x66000960 0x24>,
+ <0x67012800 0x4>,
+ <0x6501d148 0x4>,
+ <0x664d0700 0x4>;
+ reg-names = "icfg", "rst-ctrl",
+ "crmu-ctrl", "usb2-strap";
+ id-gpios = <&gpio_g 30 0>;
+ vbus-gpios = <&gpio_g 31 0>;
+ };
--
2.1.0
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH 2/3] Broadcom USB DRD Phy driver for Northstar2
@ 2016-11-30 5:55 ` Raviteja Garimella
0 siblings, 0 replies; 20+ messages in thread
From: Raviteja Garimella @ 2016-11-30 5:55 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Kishon Vijay Abraham I, Ray Jui,
Scott Branden, Jon Mason, Catalin Marinas, Will Deacon
Cc: devicetree, linux-kernel, bcm-kernel-feedback-list, linux-arm-kernel
This is driver for USB DRD Phy used in Broadcom's Northstar2
SoC. The phy can be configured to be in Device mode or Host
mode based on the type of cable connected to the port. The
driver registers to extcon framework to get appropriate
connect events for Host/Device cables connect/disconnect
states based on VBUS and ID interrupts.
Signed-off-by: Raviteja Garimella <raviteja.garimella@broadcom.com>
---
drivers/phy/Kconfig | 13 +
drivers/phy/Makefile | 1 +
drivers/phy/phy-bcm-ns2-usbdrd.c | 587 +++++++++++++++++++++++++++++++++++++++
3 files changed, 601 insertions(+)
create mode 100644 drivers/phy/phy-bcm-ns2-usbdrd.c
diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index fe00f91..b3b6a73 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -479,6 +479,19 @@ config PHY_CYGNUS_PCIE
Enable this to support the Broadcom Cygnus PCIe PHY.
If unsure, say N.
+config PHY_NS2_USB_DRD
+ tristate "Broadcom Northstar2 USB DRD PHY support"
+ depends on OF && (ARCH_BCM_IPROC || COMPILE_TEST)
+ select GENERIC_PHY
+ select EXTCON
+ default ARCH_BCM_IPROC
+ help
+ Enable this to support the Broadcom Northstar2 USB DRD PHY.
+ This driver initializes the PHY in either HOST or DEVICE mode.
+ The host or device configuration is read from device tree.
+
+ If unsure, say N.
+
source "drivers/phy/tegra/Kconfig"
config PHY_NS2_PCIE
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index a534cf5..b733ba2 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -58,5 +58,6 @@ obj-$(CONFIG_PHY_TUSB1210) += phy-tusb1210.o
obj-$(CONFIG_PHY_BRCM_SATA) += phy-brcm-sata.o
obj-$(CONFIG_PHY_PISTACHIO_USB) += phy-pistachio-usb.o
obj-$(CONFIG_PHY_CYGNUS_PCIE) += phy-bcm-cygnus-pcie.o
+obj-$(CONFIG_PHY_NS2_USB_DRD) += phy-bcm-ns2-usbdrd.o
obj-$(CONFIG_ARCH_TEGRA) += tegra/
obj-$(CONFIG_PHY_NS2_PCIE) += phy-bcm-ns2-pcie.o
diff --git a/drivers/phy/phy-bcm-ns2-usbdrd.c b/drivers/phy/phy-bcm-ns2-usbdrd.c
new file mode 100644
index 0000000..460040d
--- /dev/null
+++ b/drivers/phy/phy-bcm-ns2-usbdrd.c
@@ -0,0 +1,587 @@
+/*
+ * Copyright (C) 2016 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/delay.h>
+#include <linux/extcon.h>
+#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+#include <linux/workqueue.h>
+
+#define ICFG_DRD_AFE 0x0
+#define ICFG_MISC_STAT 0x18
+#define ICFG_DRD_P0CTL 0x1C
+#define ICFG_STRAP_CTRL 0x20
+#define ICFG_FSM_CTRL 0x24
+
+#define IDM_RST_BIT BIT(0)
+#define AFE_CORERDY_VDDC BIT(18)
+#define PHY_PLL_RESETB BIT(15)
+#define PHY_RESETB BIT(14)
+#define PHY_PLL_LOCK BIT(0)
+
+#define DRD_DEV_MODE BIT(20)
+#define OHCI_OVRCUR_POL BIT(11)
+#define ICFG_OFF_MODE BIT(6)
+#define PLL_LOCK_RETRY 1000
+
+#define EVT_DEVICE 0
+#define EVT_HOST 1
+#define EVT_IDLE 2
+
+#define DRD_HOST_MODE (BIT(2) | BIT(3))
+#define DRD_DEVICE_MODE (BIT(4) | BIT(5))
+#define DRD_HOST_VAL 0x803
+#define DRD_DEV_VAL 0x807
+#define GPIO_DELAY 20
+#define PHY_WQ_DELAY msecs_to_jiffies(600)
+
+struct ns2_phy_data;
+struct ns2_phy_driver {
+ void __iomem *icfgdrd_regs;
+ void __iomem *idmdrd_rst_ctrl;
+ void __iomem *crmu_usb2_ctrl;
+ void __iomem *usb2h_strap_reg;
+ spinlock_t lock; /* spin lock for phy driver */
+ bool host_mode;
+ struct ns2_phy_data *data;
+ struct extcon_specific_cable_nb extcon_dev;
+ struct extcon_specific_cable_nb extcon_host;
+ struct notifier_block host_nb;
+ struct notifier_block dev_nb;
+ struct delayed_work conn_work;
+ struct extcon_dev *edev;
+ struct gpio_desc *vbus_gpiod;
+ struct gpio_desc *id_gpiod;
+ int id_irq;
+ int vbus_irq;
+ unsigned long debounce_jiffies;
+ struct delayed_work wq_extcon;
+};
+
+struct ns2_phy_data {
+ struct ns2_phy_driver *driver;
+ struct phy *phy;
+ int new_state;
+ bool poweron;
+};
+
+static const unsigned int usb_extcon_cable[] = {
+ EXTCON_USB,
+ EXTCON_USB_HOST,
+ EXTCON_NONE,
+};
+
+static inline int pll_lock_stat(u32 usb_reg, int reg_mask,
+ struct ns2_phy_driver *driver)
+{
+ int retry = PLL_LOCK_RETRY;
+ u32 val;
+
+ do {
+ udelay(1);
+ val = readl(driver->icfgdrd_regs + usb_reg);
+ if (val & reg_mask)
+ return 0;
+ } while (--retry > 0);
+
+ return -EBUSY;
+}
+
+static int ns2_drd_phy_init(struct phy *phy)
+{
+ struct ns2_phy_data *data = phy_get_drvdata(phy);
+ struct ns2_phy_driver *driver = data->driver;
+ unsigned long flags;
+ u32 val;
+
+ spin_lock_irqsave(&driver->lock, flags);
+
+ val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
+
+ if (data->new_state == EVT_HOST) {
+ val &= ~DRD_DEVICE_MODE;
+ val |= DRD_HOST_MODE;
+ } else {
+ val &= ~DRD_HOST_MODE;
+ val |= DRD_DEVICE_MODE;
+ }
+ writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
+
+ spin_unlock_irqrestore(&driver->lock, flags);
+ return 0;
+}
+
+static int ns2_drd_phy_shutdown(struct phy *phy)
+{
+ struct ns2_phy_data *data = phy_get_drvdata(phy);
+ struct ns2_phy_driver *driver = data->driver;
+ unsigned long flags;
+ u32 val;
+
+ spin_lock_irqsave(&driver->lock, flags);
+ if (!data->poweron)
+ goto exit;
+
+ val = readl(driver->crmu_usb2_ctrl);
+ val &= ~AFE_CORERDY_VDDC;
+ writel(val, driver->crmu_usb2_ctrl);
+
+ driver->host_mode = 0;
+ val = readl(driver->crmu_usb2_ctrl);
+ val &= ~DRD_DEV_MODE;
+ writel(val, driver->crmu_usb2_ctrl);
+
+ /* Disable Host and Device Mode */
+ val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
+ val &= ~(DRD_HOST_MODE | DRD_DEVICE_MODE | ICFG_OFF_MODE);
+ writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
+
+ data->poweron = 0;
+exit:
+ spin_unlock_irqrestore(&driver->lock, flags);
+ return 0;
+}
+
+static int ns2_drd_phy_poweron(struct phy *phy)
+{
+ struct ns2_phy_data *data = phy_get_drvdata(phy);
+ struct ns2_phy_driver *driver = data->driver;
+ u32 extcon_event = data->new_state;
+ unsigned long flags;
+ int ret;
+ u32 val;
+
+ spin_lock_irqsave(&driver->lock, flags);
+ if (extcon_event == EVT_DEVICE) {
+ if (data->poweron)
+ goto exit;
+
+ writel(DRD_DEV_VAL, driver->icfgdrd_regs + ICFG_DRD_P0CTL);
+
+ val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
+ val &= ~(DRD_HOST_MODE | ICFG_OFF_MODE);
+ val |= DRD_DEVICE_MODE;
+ writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
+
+ val = readl(driver->idmdrd_rst_ctrl);
+ val &= ~IDM_RST_BIT;
+ writel(val, driver->idmdrd_rst_ctrl);
+
+ val = readl(driver->crmu_usb2_ctrl);
+ val |= (AFE_CORERDY_VDDC | DRD_DEV_MODE);
+ writel(val, driver->crmu_usb2_ctrl);
+
+ /* Bring PHY and PHY_PLL out of Reset */
+ val = readl(driver->crmu_usb2_ctrl);
+ val |= (PHY_PLL_RESETB | PHY_RESETB);
+ writel(val, driver->crmu_usb2_ctrl);
+
+ ret = pll_lock_stat(ICFG_MISC_STAT, PHY_PLL_LOCK, driver);
+ if (ret < 0) {
+ dev_err(&phy->dev, "Phy PLL lock failed\n");
+ goto err_shutdown;
+ }
+ } else {
+ if (data->poweron && driver->host_mode)
+ goto exit;
+
+ writel(DRD_HOST_VAL, driver->icfgdrd_regs + ICFG_DRD_P0CTL);
+
+ val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
+ val &= ~(DRD_DEVICE_MODE | ICFG_OFF_MODE);
+ val |= DRD_HOST_MODE;
+ writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
+
+ val = readl(driver->crmu_usb2_ctrl);
+ val |= AFE_CORERDY_VDDC;
+ writel(val, driver->crmu_usb2_ctrl);
+
+ ret = pll_lock_stat(ICFG_MISC_STAT, PHY_PLL_LOCK, driver);
+ if (ret < 0) {
+ dev_err(&phy->dev, "Phy PLL lock failed\n");
+ goto err_shutdown;
+ }
+
+ val = readl(driver->idmdrd_rst_ctrl);
+ val &= ~IDM_RST_BIT;
+ writel(val, driver->idmdrd_rst_ctrl);
+
+ /* port over current Polarity */
+ val = readl(driver->usb2h_strap_reg);
+ val |= OHCI_OVRCUR_POL;
+ writel(val, driver->usb2h_strap_reg);
+
+ driver->host_mode = 1;
+ }
+
+ data->poweron = 1;
+exit:
+ spin_unlock_irqrestore(&driver->lock, flags);
+ return 0;
+
+err_shutdown:
+ data->poweron = 1;
+ spin_unlock_irqrestore(&driver->lock, flags);
+ ns2_drd_phy_shutdown(phy);
+ return ret;
+}
+
+static void connect_work(struct work_struct *work)
+{
+ struct ns2_phy_driver *driver;
+ struct ns2_phy_data *data;
+ u32 extcon_event;
+
+ driver = container_of(to_delayed_work(work),
+ struct ns2_phy_driver, conn_work);
+ data = driver->data;
+ extcon_event = data->new_state;
+
+ if (extcon_event == EVT_DEVICE || extcon_event == EVT_HOST) {
+ ns2_drd_phy_init(data->phy);
+ ns2_drd_phy_poweron(data->phy);
+ } else if (extcon_event == EVT_IDLE) {
+ ns2_drd_phy_shutdown(data->phy);
+ }
+}
+
+static int drd_device_notify(struct notifier_block *self,
+ unsigned long event, void *ptr)
+{
+ struct ns2_phy_driver *driver = container_of(self,
+ struct ns2_phy_driver, dev_nb);
+
+ if (event) {
+ pr_debug("Device connected\n");
+ driver->data->new_state = EVT_DEVICE;
+ schedule_delayed_work(&driver->conn_work, 0);
+ } else {
+ pr_debug("Device disconnected\n");
+ driver->data->new_state = EVT_IDLE;
+ schedule_delayed_work(&driver->conn_work, PHY_WQ_DELAY);
+ }
+
+ return NOTIFY_DONE;
+}
+
+static int drd_host_notify(struct notifier_block *self,
+ unsigned long event, void *ptr)
+{
+ struct ns2_phy_driver *driver = container_of(self,
+ struct ns2_phy_driver, host_nb);
+
+ if (event) {
+ pr_debug("Host connected\n");
+ driver->data->new_state = EVT_HOST;
+ schedule_delayed_work(&driver->conn_work, 0);
+ } else {
+ pr_debug("Host disconnected\n");
+ driver->data->new_state = EVT_IDLE;
+ schedule_delayed_work(&driver->conn_work, PHY_WQ_DELAY);
+ }
+
+ return NOTIFY_DONE;
+}
+
+static void extcon_work(struct work_struct *work)
+{
+ struct ns2_phy_driver *driver;
+ int vbus;
+ int id;
+
+ driver = container_of(to_delayed_work(work),
+ struct ns2_phy_driver, wq_extcon);
+
+ id = gpiod_get_value_cansleep(driver->id_gpiod);
+ vbus = gpiod_get_value_cansleep(driver->vbus_gpiod);
+
+ if (!id && vbus) {
+ extcon_set_cable_state_(driver->edev, EXTCON_USB_HOST, true);
+ } else if (id && !vbus) {
+ extcon_set_cable_state_(driver->edev, EXTCON_USB_HOST, false);
+ extcon_set_cable_state_(driver->edev, EXTCON_USB, false);
+ } else if (id && vbus) {
+ extcon_set_cable_state_(driver->edev, EXTCON_USB, true);
+ }
+}
+
+static irqreturn_t gpio_irq_handler(int irq, void *dev_id)
+{
+ struct ns2_phy_driver *driver = dev_id;
+
+ queue_delayed_work(system_power_efficient_wq, &driver->wq_extcon,
+ driver->debounce_jiffies);
+
+ return IRQ_HANDLED;
+}
+
+static int register_extcon_notifier(struct ns2_phy_driver *phy_driver,
+ struct device *dev)
+{
+ struct extcon_dev *edev;
+ int ret;
+
+ phy_driver->host_nb.notifier_call = drd_host_notify;
+ phy_driver->dev_nb.notifier_call = drd_device_notify;
+
+ edev = phy_driver->edev;
+
+ /* Register for device change notification */
+ ret = extcon_register_notifier(edev, EXTCON_USB,
+ &phy_driver->dev_nb);
+ if (ret < 0) {
+ dev_err(dev, "can't register extcon_dev for %s\n", edev->name);
+ return ret;
+ }
+
+ /* Register for host change notification */
+ ret = extcon_register_notifier(edev, EXTCON_USB_HOST,
+ &phy_driver->host_nb);
+ if (ret < 0) {
+ dev_err(dev, "can't register extcon_dev for %s\n", edev->name);
+ goto err_dev;
+ }
+
+ /* Check the device cable connect state */
+ ret = extcon_get_cable_state_(edev, EXTCON_USB);
+ if (ret < 0) {
+ dev_err(dev, "can't get extcon_dev state for %s\n", edev->name);
+ goto err_host;
+ } else if (ret) {
+ phy_driver->data->new_state = EVT_DEVICE;
+ }
+
+ /* Check the host cable connect state */
+ ret = extcon_get_cable_state_(edev, EXTCON_USB_HOST);
+ if (ret < 0) {
+ dev_err(dev, "can't get extcon_dev state for %s\n", edev->name);
+ goto err_host;
+ } else if (ret) {
+ phy_driver->data->new_state = EVT_HOST;
+ }
+
+ return 0;
+
+err_host:
+ ret = extcon_unregister_notifier(edev, EXTCON_USB_HOST,
+ &phy_driver->host_nb);
+err_dev:
+ ret = extcon_unregister_notifier(edev, EXTCON_USB,
+ &phy_driver->dev_nb);
+ return ret;
+}
+
+static struct phy_ops ops = {
+ .init = ns2_drd_phy_init,
+ .power_on = ns2_drd_phy_poweron,
+ .power_off = ns2_drd_phy_shutdown,
+};
+
+static const struct of_device_id ns2_drd_phy_dt_ids[] = {
+ { .compatible = "brcm,ns2-drd-phy", },
+ { }
+};
+
+static int ns2_drd_phy_remove(struct platform_device *pdev)
+{
+ struct ns2_phy_driver *driver = dev_get_drvdata(&pdev->dev);
+
+ if (driver->edev) {
+ extcon_unregister_notifier(driver->edev, EXTCON_USB_HOST,
+ &driver->host_nb);
+ extcon_unregister_notifier(driver->edev, EXTCON_USB,
+ &driver->dev_nb);
+ }
+
+ return 0;
+}
+static int ns2_drd_phy_probe(struct platform_device *pdev)
+{
+ struct phy_provider *phy_provider;
+ struct device *dev = &pdev->dev;
+ struct ns2_phy_driver *driver;
+ struct ns2_phy_data *data;
+ struct resource *res;
+ int ret;
+ u32 val;
+
+ driver = devm_kzalloc(dev, sizeof(struct ns2_phy_driver),
+ GFP_KERNEL);
+ if (!driver)
+ return -ENOMEM;
+
+ driver->data = devm_kzalloc(dev, sizeof(struct ns2_phy_data),
+ GFP_KERNEL);
+ if (!driver->data)
+ return -ENOMEM;
+
+ spin_lock_init(&driver->lock);
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "icfg");
+ driver->icfgdrd_regs = devm_ioremap_resource(dev, res);
+ if (IS_ERR(driver->icfgdrd_regs))
+ return PTR_ERR(driver->icfgdrd_regs);
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "rst-ctrl");
+ driver->idmdrd_rst_ctrl = devm_ioremap_resource(dev, res);
+ if (IS_ERR(driver->idmdrd_rst_ctrl))
+ return PTR_ERR(driver->idmdrd_rst_ctrl);
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "crmu-ctrl");
+ driver->crmu_usb2_ctrl = devm_ioremap_resource(dev, res);
+ if (IS_ERR(driver->crmu_usb2_ctrl))
+ return PTR_ERR(driver->crmu_usb2_ctrl);
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "usb2-strap");
+ driver->usb2h_strap_reg = devm_ioremap_resource(dev, res);
+ if (IS_ERR(driver->usb2h_strap_reg))
+ return PTR_ERR(driver->usb2h_strap_reg);
+
+ /* create extcon */
+ driver->id_gpiod = devm_gpiod_get(&pdev->dev, "id", GPIOD_IN);
+ if (IS_ERR(driver->id_gpiod)) {
+ dev_err(dev, "failed to get ID GPIO\n");
+ return PTR_ERR(driver->id_gpiod);
+ }
+ driver->vbus_gpiod = devm_gpiod_get(&pdev->dev, "vbus", GPIOD_IN);
+ if (IS_ERR(driver->vbus_gpiod)) {
+ dev_err(dev, "failed to get VBUS GPIO\n");
+ return PTR_ERR(driver->vbus_gpiod);
+ }
+
+ driver->edev = devm_extcon_dev_allocate(dev, usb_extcon_cable);
+ if (IS_ERR(driver->edev)) {
+ dev_err(dev, "failed to allocate extcon device\n");
+ return -ENOMEM;
+ }
+
+ ret = devm_extcon_dev_register(dev, driver->edev);
+ if (ret < 0) {
+ dev_err(dev, "failed to register extcon device\n");
+ goto extcon_free;
+ }
+
+ ret = gpiod_set_debounce(driver->id_gpiod, GPIO_DELAY * 1000);
+ if (ret < 0)
+ driver->debounce_jiffies = msecs_to_jiffies(GPIO_DELAY);
+
+ INIT_DELAYED_WORK(&driver->wq_extcon, extcon_work);
+
+ driver->id_irq = gpiod_to_irq(driver->id_gpiod);
+ if (driver->id_irq < 0) {
+ dev_err(dev, "failed to get ID IRQ\n");
+ ret = driver->id_irq;
+ goto extcon_unregister;
+ }
+ driver->vbus_irq = gpiod_to_irq(driver->vbus_gpiod);
+ if (driver->vbus_irq < 0) {
+ dev_err(dev, "failed to get ID IRQ\n");
+ ret = driver->vbus_irq;
+ goto extcon_unregister;
+ }
+
+ ret = devm_request_threaded_irq(dev, driver->id_irq, NULL,
+ gpio_irq_handler,
+ IRQF_TRIGGER_RISING |
+ IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
+ "usb_id", driver);
+ if (ret < 0) {
+ dev_err(dev, "failed to request handler for ID IRQ\n");
+ goto extcon_unregister;
+ }
+ ret = devm_request_threaded_irq(dev, driver->vbus_irq, NULL,
+ gpio_irq_handler,
+ IRQF_TRIGGER_RISING |
+ IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
+ "usb_vbus", driver);
+ if (ret < 0) {
+ dev_err(dev, "failed to request handler for VBUS IRQ\n");
+ goto extcon_unregister;
+ }
+
+ dev_set_drvdata(dev, driver);
+ driver->host_mode = 0;
+
+ /* Shutdown all ports. They can be powered up as required */
+ val = readl(driver->crmu_usb2_ctrl);
+ val &= ~(AFE_CORERDY_VDDC | PHY_RESETB);
+ writel(val, driver->crmu_usb2_ctrl);
+
+ data = driver->data;
+ data->phy = devm_phy_create(dev, dev->of_node, &ops);
+ if (IS_ERR(data->phy)) {
+ dev_err(dev, "Failed to create usb drd phy\n");
+ ret = PTR_ERR(data->phy);
+ goto extcon_unregister;
+ }
+
+ data->driver = driver;
+ data->poweron = 0;
+ phy_set_drvdata(data->phy, data);
+
+ phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+ if (IS_ERR(phy_provider)) {
+ dev_err(dev, "Failed to register as phy provider\n");
+ ret = PTR_ERR(phy_provider);
+ goto extcon_unregister;
+ }
+
+ INIT_DELAYED_WORK(&driver->conn_work, connect_work);
+ platform_set_drvdata(pdev, driver);
+
+ ret = register_extcon_notifier(driver, dev);
+ if (ret < 0) {
+ dev_err(dev, "register extcon notifier failed (%d)\n", ret);
+ goto extcon_unregister;
+ }
+ dev_info(dev, "Registered %s\n", driver->edev->name);
+ queue_delayed_work(system_power_efficient_wq, &driver->wq_extcon,
+ driver->debounce_jiffies);
+
+ return 0;
+
+extcon_unregister:
+ devm_extcon_dev_unregister(dev, driver->edev);
+extcon_free:
+ devm_extcon_dev_free(dev, driver->edev);
+ return ret;
+}
+
+MODULE_DEVICE_TABLE(of, ns2_drd_phy_dt_ids);
+
+static struct platform_driver ns2_drd_phy_driver = {
+ .probe = ns2_drd_phy_probe,
+ .remove = ns2_drd_phy_remove,
+ .driver = {
+ .name = "bcm-ns2-usbphy",
+ .of_match_table = of_match_ptr(ns2_drd_phy_dt_ids),
+ },
+};
+module_platform_driver(ns2_drd_phy_driver);
+
+MODULE_ALIAS("platform:bcm-ns2-drd-phy");
+MODULE_AUTHOR("Broadcom");
+MODULE_DESCRIPTION("Broadcom NS2 USB2 PHY driver");
+MODULE_LICENSE("GPL v2");
--
2.1.0
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH 2/3] Broadcom USB DRD Phy driver for Northstar2
@ 2016-11-30 5:55 ` Raviteja Garimella
0 siblings, 0 replies; 20+ messages in thread
From: Raviteja Garimella @ 2016-11-30 5:55 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Kishon Vijay Abraham I, Ray Jui,
Scott Branden, Jon Mason, Catalin Marinas, Will Deacon
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
bcm-kernel-feedback-list-dY08KVG/lbpWk0Htik3J/w,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
This is driver for USB DRD Phy used in Broadcom's Northstar2
SoC. The phy can be configured to be in Device mode or Host
mode based on the type of cable connected to the port. The
driver registers to extcon framework to get appropriate
connect events for Host/Device cables connect/disconnect
states based on VBUS and ID interrupts.
Signed-off-by: Raviteja Garimella <raviteja.garimella-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>
---
drivers/phy/Kconfig | 13 +
drivers/phy/Makefile | 1 +
drivers/phy/phy-bcm-ns2-usbdrd.c | 587 +++++++++++++++++++++++++++++++++++++++
3 files changed, 601 insertions(+)
create mode 100644 drivers/phy/phy-bcm-ns2-usbdrd.c
diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index fe00f91..b3b6a73 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -479,6 +479,19 @@ config PHY_CYGNUS_PCIE
Enable this to support the Broadcom Cygnus PCIe PHY.
If unsure, say N.
+config PHY_NS2_USB_DRD
+ tristate "Broadcom Northstar2 USB DRD PHY support"
+ depends on OF && (ARCH_BCM_IPROC || COMPILE_TEST)
+ select GENERIC_PHY
+ select EXTCON
+ default ARCH_BCM_IPROC
+ help
+ Enable this to support the Broadcom Northstar2 USB DRD PHY.
+ This driver initializes the PHY in either HOST or DEVICE mode.
+ The host or device configuration is read from device tree.
+
+ If unsure, say N.
+
source "drivers/phy/tegra/Kconfig"
config PHY_NS2_PCIE
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index a534cf5..b733ba2 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -58,5 +58,6 @@ obj-$(CONFIG_PHY_TUSB1210) += phy-tusb1210.o
obj-$(CONFIG_PHY_BRCM_SATA) += phy-brcm-sata.o
obj-$(CONFIG_PHY_PISTACHIO_USB) += phy-pistachio-usb.o
obj-$(CONFIG_PHY_CYGNUS_PCIE) += phy-bcm-cygnus-pcie.o
+obj-$(CONFIG_PHY_NS2_USB_DRD) += phy-bcm-ns2-usbdrd.o
obj-$(CONFIG_ARCH_TEGRA) += tegra/
obj-$(CONFIG_PHY_NS2_PCIE) += phy-bcm-ns2-pcie.o
diff --git a/drivers/phy/phy-bcm-ns2-usbdrd.c b/drivers/phy/phy-bcm-ns2-usbdrd.c
new file mode 100644
index 0000000..460040d
--- /dev/null
+++ b/drivers/phy/phy-bcm-ns2-usbdrd.c
@@ -0,0 +1,587 @@
+/*
+ * Copyright (C) 2016 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/delay.h>
+#include <linux/extcon.h>
+#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+#include <linux/workqueue.h>
+
+#define ICFG_DRD_AFE 0x0
+#define ICFG_MISC_STAT 0x18
+#define ICFG_DRD_P0CTL 0x1C
+#define ICFG_STRAP_CTRL 0x20
+#define ICFG_FSM_CTRL 0x24
+
+#define IDM_RST_BIT BIT(0)
+#define AFE_CORERDY_VDDC BIT(18)
+#define PHY_PLL_RESETB BIT(15)
+#define PHY_RESETB BIT(14)
+#define PHY_PLL_LOCK BIT(0)
+
+#define DRD_DEV_MODE BIT(20)
+#define OHCI_OVRCUR_POL BIT(11)
+#define ICFG_OFF_MODE BIT(6)
+#define PLL_LOCK_RETRY 1000
+
+#define EVT_DEVICE 0
+#define EVT_HOST 1
+#define EVT_IDLE 2
+
+#define DRD_HOST_MODE (BIT(2) | BIT(3))
+#define DRD_DEVICE_MODE (BIT(4) | BIT(5))
+#define DRD_HOST_VAL 0x803
+#define DRD_DEV_VAL 0x807
+#define GPIO_DELAY 20
+#define PHY_WQ_DELAY msecs_to_jiffies(600)
+
+struct ns2_phy_data;
+struct ns2_phy_driver {
+ void __iomem *icfgdrd_regs;
+ void __iomem *idmdrd_rst_ctrl;
+ void __iomem *crmu_usb2_ctrl;
+ void __iomem *usb2h_strap_reg;
+ spinlock_t lock; /* spin lock for phy driver */
+ bool host_mode;
+ struct ns2_phy_data *data;
+ struct extcon_specific_cable_nb extcon_dev;
+ struct extcon_specific_cable_nb extcon_host;
+ struct notifier_block host_nb;
+ struct notifier_block dev_nb;
+ struct delayed_work conn_work;
+ struct extcon_dev *edev;
+ struct gpio_desc *vbus_gpiod;
+ struct gpio_desc *id_gpiod;
+ int id_irq;
+ int vbus_irq;
+ unsigned long debounce_jiffies;
+ struct delayed_work wq_extcon;
+};
+
+struct ns2_phy_data {
+ struct ns2_phy_driver *driver;
+ struct phy *phy;
+ int new_state;
+ bool poweron;
+};
+
+static const unsigned int usb_extcon_cable[] = {
+ EXTCON_USB,
+ EXTCON_USB_HOST,
+ EXTCON_NONE,
+};
+
+static inline int pll_lock_stat(u32 usb_reg, int reg_mask,
+ struct ns2_phy_driver *driver)
+{
+ int retry = PLL_LOCK_RETRY;
+ u32 val;
+
+ do {
+ udelay(1);
+ val = readl(driver->icfgdrd_regs + usb_reg);
+ if (val & reg_mask)
+ return 0;
+ } while (--retry > 0);
+
+ return -EBUSY;
+}
+
+static int ns2_drd_phy_init(struct phy *phy)
+{
+ struct ns2_phy_data *data = phy_get_drvdata(phy);
+ struct ns2_phy_driver *driver = data->driver;
+ unsigned long flags;
+ u32 val;
+
+ spin_lock_irqsave(&driver->lock, flags);
+
+ val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
+
+ if (data->new_state == EVT_HOST) {
+ val &= ~DRD_DEVICE_MODE;
+ val |= DRD_HOST_MODE;
+ } else {
+ val &= ~DRD_HOST_MODE;
+ val |= DRD_DEVICE_MODE;
+ }
+ writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
+
+ spin_unlock_irqrestore(&driver->lock, flags);
+ return 0;
+}
+
+static int ns2_drd_phy_shutdown(struct phy *phy)
+{
+ struct ns2_phy_data *data = phy_get_drvdata(phy);
+ struct ns2_phy_driver *driver = data->driver;
+ unsigned long flags;
+ u32 val;
+
+ spin_lock_irqsave(&driver->lock, flags);
+ if (!data->poweron)
+ goto exit;
+
+ val = readl(driver->crmu_usb2_ctrl);
+ val &= ~AFE_CORERDY_VDDC;
+ writel(val, driver->crmu_usb2_ctrl);
+
+ driver->host_mode = 0;
+ val = readl(driver->crmu_usb2_ctrl);
+ val &= ~DRD_DEV_MODE;
+ writel(val, driver->crmu_usb2_ctrl);
+
+ /* Disable Host and Device Mode */
+ val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
+ val &= ~(DRD_HOST_MODE | DRD_DEVICE_MODE | ICFG_OFF_MODE);
+ writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
+
+ data->poweron = 0;
+exit:
+ spin_unlock_irqrestore(&driver->lock, flags);
+ return 0;
+}
+
+static int ns2_drd_phy_poweron(struct phy *phy)
+{
+ struct ns2_phy_data *data = phy_get_drvdata(phy);
+ struct ns2_phy_driver *driver = data->driver;
+ u32 extcon_event = data->new_state;
+ unsigned long flags;
+ int ret;
+ u32 val;
+
+ spin_lock_irqsave(&driver->lock, flags);
+ if (extcon_event == EVT_DEVICE) {
+ if (data->poweron)
+ goto exit;
+
+ writel(DRD_DEV_VAL, driver->icfgdrd_regs + ICFG_DRD_P0CTL);
+
+ val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
+ val &= ~(DRD_HOST_MODE | ICFG_OFF_MODE);
+ val |= DRD_DEVICE_MODE;
+ writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
+
+ val = readl(driver->idmdrd_rst_ctrl);
+ val &= ~IDM_RST_BIT;
+ writel(val, driver->idmdrd_rst_ctrl);
+
+ val = readl(driver->crmu_usb2_ctrl);
+ val |= (AFE_CORERDY_VDDC | DRD_DEV_MODE);
+ writel(val, driver->crmu_usb2_ctrl);
+
+ /* Bring PHY and PHY_PLL out of Reset */
+ val = readl(driver->crmu_usb2_ctrl);
+ val |= (PHY_PLL_RESETB | PHY_RESETB);
+ writel(val, driver->crmu_usb2_ctrl);
+
+ ret = pll_lock_stat(ICFG_MISC_STAT, PHY_PLL_LOCK, driver);
+ if (ret < 0) {
+ dev_err(&phy->dev, "Phy PLL lock failed\n");
+ goto err_shutdown;
+ }
+ } else {
+ if (data->poweron && driver->host_mode)
+ goto exit;
+
+ writel(DRD_HOST_VAL, driver->icfgdrd_regs + ICFG_DRD_P0CTL);
+
+ val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
+ val &= ~(DRD_DEVICE_MODE | ICFG_OFF_MODE);
+ val |= DRD_HOST_MODE;
+ writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
+
+ val = readl(driver->crmu_usb2_ctrl);
+ val |= AFE_CORERDY_VDDC;
+ writel(val, driver->crmu_usb2_ctrl);
+
+ ret = pll_lock_stat(ICFG_MISC_STAT, PHY_PLL_LOCK, driver);
+ if (ret < 0) {
+ dev_err(&phy->dev, "Phy PLL lock failed\n");
+ goto err_shutdown;
+ }
+
+ val = readl(driver->idmdrd_rst_ctrl);
+ val &= ~IDM_RST_BIT;
+ writel(val, driver->idmdrd_rst_ctrl);
+
+ /* port over current Polarity */
+ val = readl(driver->usb2h_strap_reg);
+ val |= OHCI_OVRCUR_POL;
+ writel(val, driver->usb2h_strap_reg);
+
+ driver->host_mode = 1;
+ }
+
+ data->poweron = 1;
+exit:
+ spin_unlock_irqrestore(&driver->lock, flags);
+ return 0;
+
+err_shutdown:
+ data->poweron = 1;
+ spin_unlock_irqrestore(&driver->lock, flags);
+ ns2_drd_phy_shutdown(phy);
+ return ret;
+}
+
+static void connect_work(struct work_struct *work)
+{
+ struct ns2_phy_driver *driver;
+ struct ns2_phy_data *data;
+ u32 extcon_event;
+
+ driver = container_of(to_delayed_work(work),
+ struct ns2_phy_driver, conn_work);
+ data = driver->data;
+ extcon_event = data->new_state;
+
+ if (extcon_event == EVT_DEVICE || extcon_event == EVT_HOST) {
+ ns2_drd_phy_init(data->phy);
+ ns2_drd_phy_poweron(data->phy);
+ } else if (extcon_event == EVT_IDLE) {
+ ns2_drd_phy_shutdown(data->phy);
+ }
+}
+
+static int drd_device_notify(struct notifier_block *self,
+ unsigned long event, void *ptr)
+{
+ struct ns2_phy_driver *driver = container_of(self,
+ struct ns2_phy_driver, dev_nb);
+
+ if (event) {
+ pr_debug("Device connected\n");
+ driver->data->new_state = EVT_DEVICE;
+ schedule_delayed_work(&driver->conn_work, 0);
+ } else {
+ pr_debug("Device disconnected\n");
+ driver->data->new_state = EVT_IDLE;
+ schedule_delayed_work(&driver->conn_work, PHY_WQ_DELAY);
+ }
+
+ return NOTIFY_DONE;
+}
+
+static int drd_host_notify(struct notifier_block *self,
+ unsigned long event, void *ptr)
+{
+ struct ns2_phy_driver *driver = container_of(self,
+ struct ns2_phy_driver, host_nb);
+
+ if (event) {
+ pr_debug("Host connected\n");
+ driver->data->new_state = EVT_HOST;
+ schedule_delayed_work(&driver->conn_work, 0);
+ } else {
+ pr_debug("Host disconnected\n");
+ driver->data->new_state = EVT_IDLE;
+ schedule_delayed_work(&driver->conn_work, PHY_WQ_DELAY);
+ }
+
+ return NOTIFY_DONE;
+}
+
+static void extcon_work(struct work_struct *work)
+{
+ struct ns2_phy_driver *driver;
+ int vbus;
+ int id;
+
+ driver = container_of(to_delayed_work(work),
+ struct ns2_phy_driver, wq_extcon);
+
+ id = gpiod_get_value_cansleep(driver->id_gpiod);
+ vbus = gpiod_get_value_cansleep(driver->vbus_gpiod);
+
+ if (!id && vbus) {
+ extcon_set_cable_state_(driver->edev, EXTCON_USB_HOST, true);
+ } else if (id && !vbus) {
+ extcon_set_cable_state_(driver->edev, EXTCON_USB_HOST, false);
+ extcon_set_cable_state_(driver->edev, EXTCON_USB, false);
+ } else if (id && vbus) {
+ extcon_set_cable_state_(driver->edev, EXTCON_USB, true);
+ }
+}
+
+static irqreturn_t gpio_irq_handler(int irq, void *dev_id)
+{
+ struct ns2_phy_driver *driver = dev_id;
+
+ queue_delayed_work(system_power_efficient_wq, &driver->wq_extcon,
+ driver->debounce_jiffies);
+
+ return IRQ_HANDLED;
+}
+
+static int register_extcon_notifier(struct ns2_phy_driver *phy_driver,
+ struct device *dev)
+{
+ struct extcon_dev *edev;
+ int ret;
+
+ phy_driver->host_nb.notifier_call = drd_host_notify;
+ phy_driver->dev_nb.notifier_call = drd_device_notify;
+
+ edev = phy_driver->edev;
+
+ /* Register for device change notification */
+ ret = extcon_register_notifier(edev, EXTCON_USB,
+ &phy_driver->dev_nb);
+ if (ret < 0) {
+ dev_err(dev, "can't register extcon_dev for %s\n", edev->name);
+ return ret;
+ }
+
+ /* Register for host change notification */
+ ret = extcon_register_notifier(edev, EXTCON_USB_HOST,
+ &phy_driver->host_nb);
+ if (ret < 0) {
+ dev_err(dev, "can't register extcon_dev for %s\n", edev->name);
+ goto err_dev;
+ }
+
+ /* Check the device cable connect state */
+ ret = extcon_get_cable_state_(edev, EXTCON_USB);
+ if (ret < 0) {
+ dev_err(dev, "can't get extcon_dev state for %s\n", edev->name);
+ goto err_host;
+ } else if (ret) {
+ phy_driver->data->new_state = EVT_DEVICE;
+ }
+
+ /* Check the host cable connect state */
+ ret = extcon_get_cable_state_(edev, EXTCON_USB_HOST);
+ if (ret < 0) {
+ dev_err(dev, "can't get extcon_dev state for %s\n", edev->name);
+ goto err_host;
+ } else if (ret) {
+ phy_driver->data->new_state = EVT_HOST;
+ }
+
+ return 0;
+
+err_host:
+ ret = extcon_unregister_notifier(edev, EXTCON_USB_HOST,
+ &phy_driver->host_nb);
+err_dev:
+ ret = extcon_unregister_notifier(edev, EXTCON_USB,
+ &phy_driver->dev_nb);
+ return ret;
+}
+
+static struct phy_ops ops = {
+ .init = ns2_drd_phy_init,
+ .power_on = ns2_drd_phy_poweron,
+ .power_off = ns2_drd_phy_shutdown,
+};
+
+static const struct of_device_id ns2_drd_phy_dt_ids[] = {
+ { .compatible = "brcm,ns2-drd-phy", },
+ { }
+};
+
+static int ns2_drd_phy_remove(struct platform_device *pdev)
+{
+ struct ns2_phy_driver *driver = dev_get_drvdata(&pdev->dev);
+
+ if (driver->edev) {
+ extcon_unregister_notifier(driver->edev, EXTCON_USB_HOST,
+ &driver->host_nb);
+ extcon_unregister_notifier(driver->edev, EXTCON_USB,
+ &driver->dev_nb);
+ }
+
+ return 0;
+}
+static int ns2_drd_phy_probe(struct platform_device *pdev)
+{
+ struct phy_provider *phy_provider;
+ struct device *dev = &pdev->dev;
+ struct ns2_phy_driver *driver;
+ struct ns2_phy_data *data;
+ struct resource *res;
+ int ret;
+ u32 val;
+
+ driver = devm_kzalloc(dev, sizeof(struct ns2_phy_driver),
+ GFP_KERNEL);
+ if (!driver)
+ return -ENOMEM;
+
+ driver->data = devm_kzalloc(dev, sizeof(struct ns2_phy_data),
+ GFP_KERNEL);
+ if (!driver->data)
+ return -ENOMEM;
+
+ spin_lock_init(&driver->lock);
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "icfg");
+ driver->icfgdrd_regs = devm_ioremap_resource(dev, res);
+ if (IS_ERR(driver->icfgdrd_regs))
+ return PTR_ERR(driver->icfgdrd_regs);
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "rst-ctrl");
+ driver->idmdrd_rst_ctrl = devm_ioremap_resource(dev, res);
+ if (IS_ERR(driver->idmdrd_rst_ctrl))
+ return PTR_ERR(driver->idmdrd_rst_ctrl);
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "crmu-ctrl");
+ driver->crmu_usb2_ctrl = devm_ioremap_resource(dev, res);
+ if (IS_ERR(driver->crmu_usb2_ctrl))
+ return PTR_ERR(driver->crmu_usb2_ctrl);
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "usb2-strap");
+ driver->usb2h_strap_reg = devm_ioremap_resource(dev, res);
+ if (IS_ERR(driver->usb2h_strap_reg))
+ return PTR_ERR(driver->usb2h_strap_reg);
+
+ /* create extcon */
+ driver->id_gpiod = devm_gpiod_get(&pdev->dev, "id", GPIOD_IN);
+ if (IS_ERR(driver->id_gpiod)) {
+ dev_err(dev, "failed to get ID GPIO\n");
+ return PTR_ERR(driver->id_gpiod);
+ }
+ driver->vbus_gpiod = devm_gpiod_get(&pdev->dev, "vbus", GPIOD_IN);
+ if (IS_ERR(driver->vbus_gpiod)) {
+ dev_err(dev, "failed to get VBUS GPIO\n");
+ return PTR_ERR(driver->vbus_gpiod);
+ }
+
+ driver->edev = devm_extcon_dev_allocate(dev, usb_extcon_cable);
+ if (IS_ERR(driver->edev)) {
+ dev_err(dev, "failed to allocate extcon device\n");
+ return -ENOMEM;
+ }
+
+ ret = devm_extcon_dev_register(dev, driver->edev);
+ if (ret < 0) {
+ dev_err(dev, "failed to register extcon device\n");
+ goto extcon_free;
+ }
+
+ ret = gpiod_set_debounce(driver->id_gpiod, GPIO_DELAY * 1000);
+ if (ret < 0)
+ driver->debounce_jiffies = msecs_to_jiffies(GPIO_DELAY);
+
+ INIT_DELAYED_WORK(&driver->wq_extcon, extcon_work);
+
+ driver->id_irq = gpiod_to_irq(driver->id_gpiod);
+ if (driver->id_irq < 0) {
+ dev_err(dev, "failed to get ID IRQ\n");
+ ret = driver->id_irq;
+ goto extcon_unregister;
+ }
+ driver->vbus_irq = gpiod_to_irq(driver->vbus_gpiod);
+ if (driver->vbus_irq < 0) {
+ dev_err(dev, "failed to get ID IRQ\n");
+ ret = driver->vbus_irq;
+ goto extcon_unregister;
+ }
+
+ ret = devm_request_threaded_irq(dev, driver->id_irq, NULL,
+ gpio_irq_handler,
+ IRQF_TRIGGER_RISING |
+ IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
+ "usb_id", driver);
+ if (ret < 0) {
+ dev_err(dev, "failed to request handler for ID IRQ\n");
+ goto extcon_unregister;
+ }
+ ret = devm_request_threaded_irq(dev, driver->vbus_irq, NULL,
+ gpio_irq_handler,
+ IRQF_TRIGGER_RISING |
+ IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
+ "usb_vbus", driver);
+ if (ret < 0) {
+ dev_err(dev, "failed to request handler for VBUS IRQ\n");
+ goto extcon_unregister;
+ }
+
+ dev_set_drvdata(dev, driver);
+ driver->host_mode = 0;
+
+ /* Shutdown all ports. They can be powered up as required */
+ val = readl(driver->crmu_usb2_ctrl);
+ val &= ~(AFE_CORERDY_VDDC | PHY_RESETB);
+ writel(val, driver->crmu_usb2_ctrl);
+
+ data = driver->data;
+ data->phy = devm_phy_create(dev, dev->of_node, &ops);
+ if (IS_ERR(data->phy)) {
+ dev_err(dev, "Failed to create usb drd phy\n");
+ ret = PTR_ERR(data->phy);
+ goto extcon_unregister;
+ }
+
+ data->driver = driver;
+ data->poweron = 0;
+ phy_set_drvdata(data->phy, data);
+
+ phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+ if (IS_ERR(phy_provider)) {
+ dev_err(dev, "Failed to register as phy provider\n");
+ ret = PTR_ERR(phy_provider);
+ goto extcon_unregister;
+ }
+
+ INIT_DELAYED_WORK(&driver->conn_work, connect_work);
+ platform_set_drvdata(pdev, driver);
+
+ ret = register_extcon_notifier(driver, dev);
+ if (ret < 0) {
+ dev_err(dev, "register extcon notifier failed (%d)\n", ret);
+ goto extcon_unregister;
+ }
+ dev_info(dev, "Registered %s\n", driver->edev->name);
+ queue_delayed_work(system_power_efficient_wq, &driver->wq_extcon,
+ driver->debounce_jiffies);
+
+ return 0;
+
+extcon_unregister:
+ devm_extcon_dev_unregister(dev, driver->edev);
+extcon_free:
+ devm_extcon_dev_free(dev, driver->edev);
+ return ret;
+}
+
+MODULE_DEVICE_TABLE(of, ns2_drd_phy_dt_ids);
+
+static struct platform_driver ns2_drd_phy_driver = {
+ .probe = ns2_drd_phy_probe,
+ .remove = ns2_drd_phy_remove,
+ .driver = {
+ .name = "bcm-ns2-usbphy",
+ .of_match_table = of_match_ptr(ns2_drd_phy_dt_ids),
+ },
+};
+module_platform_driver(ns2_drd_phy_driver);
+
+MODULE_ALIAS("platform:bcm-ns2-drd-phy");
+MODULE_AUTHOR("Broadcom");
+MODULE_DESCRIPTION("Broadcom NS2 USB2 PHY driver");
+MODULE_LICENSE("GPL v2");
--
2.1.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH 2/3] Broadcom USB DRD Phy driver for Northstar2
@ 2016-11-30 5:55 ` Raviteja Garimella
0 siblings, 0 replies; 20+ messages in thread
From: Raviteja Garimella @ 2016-11-30 5:55 UTC (permalink / raw)
To: linux-arm-kernel
This is driver for USB DRD Phy used in Broadcom's Northstar2
SoC. The phy can be configured to be in Device mode or Host
mode based on the type of cable connected to the port. The
driver registers to extcon framework to get appropriate
connect events for Host/Device cables connect/disconnect
states based on VBUS and ID interrupts.
Signed-off-by: Raviteja Garimella <raviteja.garimella@broadcom.com>
---
drivers/phy/Kconfig | 13 +
drivers/phy/Makefile | 1 +
drivers/phy/phy-bcm-ns2-usbdrd.c | 587 +++++++++++++++++++++++++++++++++++++++
3 files changed, 601 insertions(+)
create mode 100644 drivers/phy/phy-bcm-ns2-usbdrd.c
diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index fe00f91..b3b6a73 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -479,6 +479,19 @@ config PHY_CYGNUS_PCIE
Enable this to support the Broadcom Cygnus PCIe PHY.
If unsure, say N.
+config PHY_NS2_USB_DRD
+ tristate "Broadcom Northstar2 USB DRD PHY support"
+ depends on OF && (ARCH_BCM_IPROC || COMPILE_TEST)
+ select GENERIC_PHY
+ select EXTCON
+ default ARCH_BCM_IPROC
+ help
+ Enable this to support the Broadcom Northstar2 USB DRD PHY.
+ This driver initializes the PHY in either HOST or DEVICE mode.
+ The host or device configuration is read from device tree.
+
+ If unsure, say N.
+
source "drivers/phy/tegra/Kconfig"
config PHY_NS2_PCIE
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index a534cf5..b733ba2 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -58,5 +58,6 @@ obj-$(CONFIG_PHY_TUSB1210) += phy-tusb1210.o
obj-$(CONFIG_PHY_BRCM_SATA) += phy-brcm-sata.o
obj-$(CONFIG_PHY_PISTACHIO_USB) += phy-pistachio-usb.o
obj-$(CONFIG_PHY_CYGNUS_PCIE) += phy-bcm-cygnus-pcie.o
+obj-$(CONFIG_PHY_NS2_USB_DRD) += phy-bcm-ns2-usbdrd.o
obj-$(CONFIG_ARCH_TEGRA) += tegra/
obj-$(CONFIG_PHY_NS2_PCIE) += phy-bcm-ns2-pcie.o
diff --git a/drivers/phy/phy-bcm-ns2-usbdrd.c b/drivers/phy/phy-bcm-ns2-usbdrd.c
new file mode 100644
index 0000000..460040d
--- /dev/null
+++ b/drivers/phy/phy-bcm-ns2-usbdrd.c
@@ -0,0 +1,587 @@
+/*
+ * Copyright (C) 2016 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/delay.h>
+#include <linux/extcon.h>
+#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+#include <linux/workqueue.h>
+
+#define ICFG_DRD_AFE 0x0
+#define ICFG_MISC_STAT 0x18
+#define ICFG_DRD_P0CTL 0x1C
+#define ICFG_STRAP_CTRL 0x20
+#define ICFG_FSM_CTRL 0x24
+
+#define IDM_RST_BIT BIT(0)
+#define AFE_CORERDY_VDDC BIT(18)
+#define PHY_PLL_RESETB BIT(15)
+#define PHY_RESETB BIT(14)
+#define PHY_PLL_LOCK BIT(0)
+
+#define DRD_DEV_MODE BIT(20)
+#define OHCI_OVRCUR_POL BIT(11)
+#define ICFG_OFF_MODE BIT(6)
+#define PLL_LOCK_RETRY 1000
+
+#define EVT_DEVICE 0
+#define EVT_HOST 1
+#define EVT_IDLE 2
+
+#define DRD_HOST_MODE (BIT(2) | BIT(3))
+#define DRD_DEVICE_MODE (BIT(4) | BIT(5))
+#define DRD_HOST_VAL 0x803
+#define DRD_DEV_VAL 0x807
+#define GPIO_DELAY 20
+#define PHY_WQ_DELAY msecs_to_jiffies(600)
+
+struct ns2_phy_data;
+struct ns2_phy_driver {
+ void __iomem *icfgdrd_regs;
+ void __iomem *idmdrd_rst_ctrl;
+ void __iomem *crmu_usb2_ctrl;
+ void __iomem *usb2h_strap_reg;
+ spinlock_t lock; /* spin lock for phy driver */
+ bool host_mode;
+ struct ns2_phy_data *data;
+ struct extcon_specific_cable_nb extcon_dev;
+ struct extcon_specific_cable_nb extcon_host;
+ struct notifier_block host_nb;
+ struct notifier_block dev_nb;
+ struct delayed_work conn_work;
+ struct extcon_dev *edev;
+ struct gpio_desc *vbus_gpiod;
+ struct gpio_desc *id_gpiod;
+ int id_irq;
+ int vbus_irq;
+ unsigned long debounce_jiffies;
+ struct delayed_work wq_extcon;
+};
+
+struct ns2_phy_data {
+ struct ns2_phy_driver *driver;
+ struct phy *phy;
+ int new_state;
+ bool poweron;
+};
+
+static const unsigned int usb_extcon_cable[] = {
+ EXTCON_USB,
+ EXTCON_USB_HOST,
+ EXTCON_NONE,
+};
+
+static inline int pll_lock_stat(u32 usb_reg, int reg_mask,
+ struct ns2_phy_driver *driver)
+{
+ int retry = PLL_LOCK_RETRY;
+ u32 val;
+
+ do {
+ udelay(1);
+ val = readl(driver->icfgdrd_regs + usb_reg);
+ if (val & reg_mask)
+ return 0;
+ } while (--retry > 0);
+
+ return -EBUSY;
+}
+
+static int ns2_drd_phy_init(struct phy *phy)
+{
+ struct ns2_phy_data *data = phy_get_drvdata(phy);
+ struct ns2_phy_driver *driver = data->driver;
+ unsigned long flags;
+ u32 val;
+
+ spin_lock_irqsave(&driver->lock, flags);
+
+ val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
+
+ if (data->new_state == EVT_HOST) {
+ val &= ~DRD_DEVICE_MODE;
+ val |= DRD_HOST_MODE;
+ } else {
+ val &= ~DRD_HOST_MODE;
+ val |= DRD_DEVICE_MODE;
+ }
+ writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
+
+ spin_unlock_irqrestore(&driver->lock, flags);
+ return 0;
+}
+
+static int ns2_drd_phy_shutdown(struct phy *phy)
+{
+ struct ns2_phy_data *data = phy_get_drvdata(phy);
+ struct ns2_phy_driver *driver = data->driver;
+ unsigned long flags;
+ u32 val;
+
+ spin_lock_irqsave(&driver->lock, flags);
+ if (!data->poweron)
+ goto exit;
+
+ val = readl(driver->crmu_usb2_ctrl);
+ val &= ~AFE_CORERDY_VDDC;
+ writel(val, driver->crmu_usb2_ctrl);
+
+ driver->host_mode = 0;
+ val = readl(driver->crmu_usb2_ctrl);
+ val &= ~DRD_DEV_MODE;
+ writel(val, driver->crmu_usb2_ctrl);
+
+ /* Disable Host and Device Mode */
+ val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
+ val &= ~(DRD_HOST_MODE | DRD_DEVICE_MODE | ICFG_OFF_MODE);
+ writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
+
+ data->poweron = 0;
+exit:
+ spin_unlock_irqrestore(&driver->lock, flags);
+ return 0;
+}
+
+static int ns2_drd_phy_poweron(struct phy *phy)
+{
+ struct ns2_phy_data *data = phy_get_drvdata(phy);
+ struct ns2_phy_driver *driver = data->driver;
+ u32 extcon_event = data->new_state;
+ unsigned long flags;
+ int ret;
+ u32 val;
+
+ spin_lock_irqsave(&driver->lock, flags);
+ if (extcon_event == EVT_DEVICE) {
+ if (data->poweron)
+ goto exit;
+
+ writel(DRD_DEV_VAL, driver->icfgdrd_regs + ICFG_DRD_P0CTL);
+
+ val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
+ val &= ~(DRD_HOST_MODE | ICFG_OFF_MODE);
+ val |= DRD_DEVICE_MODE;
+ writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
+
+ val = readl(driver->idmdrd_rst_ctrl);
+ val &= ~IDM_RST_BIT;
+ writel(val, driver->idmdrd_rst_ctrl);
+
+ val = readl(driver->crmu_usb2_ctrl);
+ val |= (AFE_CORERDY_VDDC | DRD_DEV_MODE);
+ writel(val, driver->crmu_usb2_ctrl);
+
+ /* Bring PHY and PHY_PLL out of Reset */
+ val = readl(driver->crmu_usb2_ctrl);
+ val |= (PHY_PLL_RESETB | PHY_RESETB);
+ writel(val, driver->crmu_usb2_ctrl);
+
+ ret = pll_lock_stat(ICFG_MISC_STAT, PHY_PLL_LOCK, driver);
+ if (ret < 0) {
+ dev_err(&phy->dev, "Phy PLL lock failed\n");
+ goto err_shutdown;
+ }
+ } else {
+ if (data->poweron && driver->host_mode)
+ goto exit;
+
+ writel(DRD_HOST_VAL, driver->icfgdrd_regs + ICFG_DRD_P0CTL);
+
+ val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
+ val &= ~(DRD_DEVICE_MODE | ICFG_OFF_MODE);
+ val |= DRD_HOST_MODE;
+ writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
+
+ val = readl(driver->crmu_usb2_ctrl);
+ val |= AFE_CORERDY_VDDC;
+ writel(val, driver->crmu_usb2_ctrl);
+
+ ret = pll_lock_stat(ICFG_MISC_STAT, PHY_PLL_LOCK, driver);
+ if (ret < 0) {
+ dev_err(&phy->dev, "Phy PLL lock failed\n");
+ goto err_shutdown;
+ }
+
+ val = readl(driver->idmdrd_rst_ctrl);
+ val &= ~IDM_RST_BIT;
+ writel(val, driver->idmdrd_rst_ctrl);
+
+ /* port over current Polarity */
+ val = readl(driver->usb2h_strap_reg);
+ val |= OHCI_OVRCUR_POL;
+ writel(val, driver->usb2h_strap_reg);
+
+ driver->host_mode = 1;
+ }
+
+ data->poweron = 1;
+exit:
+ spin_unlock_irqrestore(&driver->lock, flags);
+ return 0;
+
+err_shutdown:
+ data->poweron = 1;
+ spin_unlock_irqrestore(&driver->lock, flags);
+ ns2_drd_phy_shutdown(phy);
+ return ret;
+}
+
+static void connect_work(struct work_struct *work)
+{
+ struct ns2_phy_driver *driver;
+ struct ns2_phy_data *data;
+ u32 extcon_event;
+
+ driver = container_of(to_delayed_work(work),
+ struct ns2_phy_driver, conn_work);
+ data = driver->data;
+ extcon_event = data->new_state;
+
+ if (extcon_event == EVT_DEVICE || extcon_event == EVT_HOST) {
+ ns2_drd_phy_init(data->phy);
+ ns2_drd_phy_poweron(data->phy);
+ } else if (extcon_event == EVT_IDLE) {
+ ns2_drd_phy_shutdown(data->phy);
+ }
+}
+
+static int drd_device_notify(struct notifier_block *self,
+ unsigned long event, void *ptr)
+{
+ struct ns2_phy_driver *driver = container_of(self,
+ struct ns2_phy_driver, dev_nb);
+
+ if (event) {
+ pr_debug("Device connected\n");
+ driver->data->new_state = EVT_DEVICE;
+ schedule_delayed_work(&driver->conn_work, 0);
+ } else {
+ pr_debug("Device disconnected\n");
+ driver->data->new_state = EVT_IDLE;
+ schedule_delayed_work(&driver->conn_work, PHY_WQ_DELAY);
+ }
+
+ return NOTIFY_DONE;
+}
+
+static int drd_host_notify(struct notifier_block *self,
+ unsigned long event, void *ptr)
+{
+ struct ns2_phy_driver *driver = container_of(self,
+ struct ns2_phy_driver, host_nb);
+
+ if (event) {
+ pr_debug("Host connected\n");
+ driver->data->new_state = EVT_HOST;
+ schedule_delayed_work(&driver->conn_work, 0);
+ } else {
+ pr_debug("Host disconnected\n");
+ driver->data->new_state = EVT_IDLE;
+ schedule_delayed_work(&driver->conn_work, PHY_WQ_DELAY);
+ }
+
+ return NOTIFY_DONE;
+}
+
+static void extcon_work(struct work_struct *work)
+{
+ struct ns2_phy_driver *driver;
+ int vbus;
+ int id;
+
+ driver = container_of(to_delayed_work(work),
+ struct ns2_phy_driver, wq_extcon);
+
+ id = gpiod_get_value_cansleep(driver->id_gpiod);
+ vbus = gpiod_get_value_cansleep(driver->vbus_gpiod);
+
+ if (!id && vbus) {
+ extcon_set_cable_state_(driver->edev, EXTCON_USB_HOST, true);
+ } else if (id && !vbus) {
+ extcon_set_cable_state_(driver->edev, EXTCON_USB_HOST, false);
+ extcon_set_cable_state_(driver->edev, EXTCON_USB, false);
+ } else if (id && vbus) {
+ extcon_set_cable_state_(driver->edev, EXTCON_USB, true);
+ }
+}
+
+static irqreturn_t gpio_irq_handler(int irq, void *dev_id)
+{
+ struct ns2_phy_driver *driver = dev_id;
+
+ queue_delayed_work(system_power_efficient_wq, &driver->wq_extcon,
+ driver->debounce_jiffies);
+
+ return IRQ_HANDLED;
+}
+
+static int register_extcon_notifier(struct ns2_phy_driver *phy_driver,
+ struct device *dev)
+{
+ struct extcon_dev *edev;
+ int ret;
+
+ phy_driver->host_nb.notifier_call = drd_host_notify;
+ phy_driver->dev_nb.notifier_call = drd_device_notify;
+
+ edev = phy_driver->edev;
+
+ /* Register for device change notification */
+ ret = extcon_register_notifier(edev, EXTCON_USB,
+ &phy_driver->dev_nb);
+ if (ret < 0) {
+ dev_err(dev, "can't register extcon_dev for %s\n", edev->name);
+ return ret;
+ }
+
+ /* Register for host change notification */
+ ret = extcon_register_notifier(edev, EXTCON_USB_HOST,
+ &phy_driver->host_nb);
+ if (ret < 0) {
+ dev_err(dev, "can't register extcon_dev for %s\n", edev->name);
+ goto err_dev;
+ }
+
+ /* Check the device cable connect state */
+ ret = extcon_get_cable_state_(edev, EXTCON_USB);
+ if (ret < 0) {
+ dev_err(dev, "can't get extcon_dev state for %s\n", edev->name);
+ goto err_host;
+ } else if (ret) {
+ phy_driver->data->new_state = EVT_DEVICE;
+ }
+
+ /* Check the host cable connect state */
+ ret = extcon_get_cable_state_(edev, EXTCON_USB_HOST);
+ if (ret < 0) {
+ dev_err(dev, "can't get extcon_dev state for %s\n", edev->name);
+ goto err_host;
+ } else if (ret) {
+ phy_driver->data->new_state = EVT_HOST;
+ }
+
+ return 0;
+
+err_host:
+ ret = extcon_unregister_notifier(edev, EXTCON_USB_HOST,
+ &phy_driver->host_nb);
+err_dev:
+ ret = extcon_unregister_notifier(edev, EXTCON_USB,
+ &phy_driver->dev_nb);
+ return ret;
+}
+
+static struct phy_ops ops = {
+ .init = ns2_drd_phy_init,
+ .power_on = ns2_drd_phy_poweron,
+ .power_off = ns2_drd_phy_shutdown,
+};
+
+static const struct of_device_id ns2_drd_phy_dt_ids[] = {
+ { .compatible = "brcm,ns2-drd-phy", },
+ { }
+};
+
+static int ns2_drd_phy_remove(struct platform_device *pdev)
+{
+ struct ns2_phy_driver *driver = dev_get_drvdata(&pdev->dev);
+
+ if (driver->edev) {
+ extcon_unregister_notifier(driver->edev, EXTCON_USB_HOST,
+ &driver->host_nb);
+ extcon_unregister_notifier(driver->edev, EXTCON_USB,
+ &driver->dev_nb);
+ }
+
+ return 0;
+}
+static int ns2_drd_phy_probe(struct platform_device *pdev)
+{
+ struct phy_provider *phy_provider;
+ struct device *dev = &pdev->dev;
+ struct ns2_phy_driver *driver;
+ struct ns2_phy_data *data;
+ struct resource *res;
+ int ret;
+ u32 val;
+
+ driver = devm_kzalloc(dev, sizeof(struct ns2_phy_driver),
+ GFP_KERNEL);
+ if (!driver)
+ return -ENOMEM;
+
+ driver->data = devm_kzalloc(dev, sizeof(struct ns2_phy_data),
+ GFP_KERNEL);
+ if (!driver->data)
+ return -ENOMEM;
+
+ spin_lock_init(&driver->lock);
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "icfg");
+ driver->icfgdrd_regs = devm_ioremap_resource(dev, res);
+ if (IS_ERR(driver->icfgdrd_regs))
+ return PTR_ERR(driver->icfgdrd_regs);
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "rst-ctrl");
+ driver->idmdrd_rst_ctrl = devm_ioremap_resource(dev, res);
+ if (IS_ERR(driver->idmdrd_rst_ctrl))
+ return PTR_ERR(driver->idmdrd_rst_ctrl);
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "crmu-ctrl");
+ driver->crmu_usb2_ctrl = devm_ioremap_resource(dev, res);
+ if (IS_ERR(driver->crmu_usb2_ctrl))
+ return PTR_ERR(driver->crmu_usb2_ctrl);
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "usb2-strap");
+ driver->usb2h_strap_reg = devm_ioremap_resource(dev, res);
+ if (IS_ERR(driver->usb2h_strap_reg))
+ return PTR_ERR(driver->usb2h_strap_reg);
+
+ /* create extcon */
+ driver->id_gpiod = devm_gpiod_get(&pdev->dev, "id", GPIOD_IN);
+ if (IS_ERR(driver->id_gpiod)) {
+ dev_err(dev, "failed to get ID GPIO\n");
+ return PTR_ERR(driver->id_gpiod);
+ }
+ driver->vbus_gpiod = devm_gpiod_get(&pdev->dev, "vbus", GPIOD_IN);
+ if (IS_ERR(driver->vbus_gpiod)) {
+ dev_err(dev, "failed to get VBUS GPIO\n");
+ return PTR_ERR(driver->vbus_gpiod);
+ }
+
+ driver->edev = devm_extcon_dev_allocate(dev, usb_extcon_cable);
+ if (IS_ERR(driver->edev)) {
+ dev_err(dev, "failed to allocate extcon device\n");
+ return -ENOMEM;
+ }
+
+ ret = devm_extcon_dev_register(dev, driver->edev);
+ if (ret < 0) {
+ dev_err(dev, "failed to register extcon device\n");
+ goto extcon_free;
+ }
+
+ ret = gpiod_set_debounce(driver->id_gpiod, GPIO_DELAY * 1000);
+ if (ret < 0)
+ driver->debounce_jiffies = msecs_to_jiffies(GPIO_DELAY);
+
+ INIT_DELAYED_WORK(&driver->wq_extcon, extcon_work);
+
+ driver->id_irq = gpiod_to_irq(driver->id_gpiod);
+ if (driver->id_irq < 0) {
+ dev_err(dev, "failed to get ID IRQ\n");
+ ret = driver->id_irq;
+ goto extcon_unregister;
+ }
+ driver->vbus_irq = gpiod_to_irq(driver->vbus_gpiod);
+ if (driver->vbus_irq < 0) {
+ dev_err(dev, "failed to get ID IRQ\n");
+ ret = driver->vbus_irq;
+ goto extcon_unregister;
+ }
+
+ ret = devm_request_threaded_irq(dev, driver->id_irq, NULL,
+ gpio_irq_handler,
+ IRQF_TRIGGER_RISING |
+ IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
+ "usb_id", driver);
+ if (ret < 0) {
+ dev_err(dev, "failed to request handler for ID IRQ\n");
+ goto extcon_unregister;
+ }
+ ret = devm_request_threaded_irq(dev, driver->vbus_irq, NULL,
+ gpio_irq_handler,
+ IRQF_TRIGGER_RISING |
+ IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
+ "usb_vbus", driver);
+ if (ret < 0) {
+ dev_err(dev, "failed to request handler for VBUS IRQ\n");
+ goto extcon_unregister;
+ }
+
+ dev_set_drvdata(dev, driver);
+ driver->host_mode = 0;
+
+ /* Shutdown all ports. They can be powered up as required */
+ val = readl(driver->crmu_usb2_ctrl);
+ val &= ~(AFE_CORERDY_VDDC | PHY_RESETB);
+ writel(val, driver->crmu_usb2_ctrl);
+
+ data = driver->data;
+ data->phy = devm_phy_create(dev, dev->of_node, &ops);
+ if (IS_ERR(data->phy)) {
+ dev_err(dev, "Failed to create usb drd phy\n");
+ ret = PTR_ERR(data->phy);
+ goto extcon_unregister;
+ }
+
+ data->driver = driver;
+ data->poweron = 0;
+ phy_set_drvdata(data->phy, data);
+
+ phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+ if (IS_ERR(phy_provider)) {
+ dev_err(dev, "Failed to register as phy provider\n");
+ ret = PTR_ERR(phy_provider);
+ goto extcon_unregister;
+ }
+
+ INIT_DELAYED_WORK(&driver->conn_work, connect_work);
+ platform_set_drvdata(pdev, driver);
+
+ ret = register_extcon_notifier(driver, dev);
+ if (ret < 0) {
+ dev_err(dev, "register extcon notifier failed (%d)\n", ret);
+ goto extcon_unregister;
+ }
+ dev_info(dev, "Registered %s\n", driver->edev->name);
+ queue_delayed_work(system_power_efficient_wq, &driver->wq_extcon,
+ driver->debounce_jiffies);
+
+ return 0;
+
+extcon_unregister:
+ devm_extcon_dev_unregister(dev, driver->edev);
+extcon_free:
+ devm_extcon_dev_free(dev, driver->edev);
+ return ret;
+}
+
+MODULE_DEVICE_TABLE(of, ns2_drd_phy_dt_ids);
+
+static struct platform_driver ns2_drd_phy_driver = {
+ .probe = ns2_drd_phy_probe,
+ .remove = ns2_drd_phy_remove,
+ .driver = {
+ .name = "bcm-ns2-usbphy",
+ .of_match_table = of_match_ptr(ns2_drd_phy_dt_ids),
+ },
+};
+module_platform_driver(ns2_drd_phy_driver);
+
+MODULE_ALIAS("platform:bcm-ns2-drd-phy");
+MODULE_AUTHOR("Broadcom");
+MODULE_DESCRIPTION("Broadcom NS2 USB2 PHY driver");
+MODULE_LICENSE("GPL v2");
--
2.1.0
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH 3/3] DT nodes for Broadcom Northstar2 USB DRD Phy
2016-11-30 5:55 ` Raviteja Garimella
@ 2016-11-30 5:55 ` Raviteja Garimella
-1 siblings, 0 replies; 20+ messages in thread
From: Raviteja Garimella @ 2016-11-30 5:55 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Kishon Vijay Abraham I, Ray Jui,
Scott Branden, Jon Mason, Catalin Marinas, Will Deacon
Cc: devicetree, linux-kernel, bcm-kernel-feedback-list, linux-arm-kernel
This patch adds device tree nodes for USB Dual Role Device Phy for
Broadcom's Northstar2 SoC.
Signed-off-by: Raviteja Garimella <raviteja.garimella@broadcom.com>
---
arch/arm64/boot/dts/broadcom/ns2.dtsi | 14 ++++++++++++++
1 file changed, 14 insertions(+)
diff --git a/arch/arm64/boot/dts/broadcom/ns2.dtsi b/arch/arm64/boot/dts/broadcom/ns2.dtsi
index d95dc40..e9d3496 100644
--- a/arch/arm64/boot/dts/broadcom/ns2.dtsi
+++ b/arch/arm64/boot/dts/broadcom/ns2.dtsi
@@ -299,6 +299,20 @@
};
};
+ usbdrd_phy: phy@66000960 {
+ #phy-cells = <0>;
+ compatible = "brcm,ns2-drd-phy";
+ reg = <0x66000960 0x24>,
+ <0x67012800 0x4>,
+ <0x6501d148 0x4>,
+ <0x664d0700 0x4>;
+ reg-names = "icfg", "rst-ctrl",
+ "crmu-ctrl", "usb2-strap";
+ id-gpios = <&gpio_g 30 0>;
+ vbus-gpios = <&gpio_g 31 0>;
+ status = "disabled";
+ };
+
pwm: pwm@66010000 {
compatible = "brcm,iproc-pwm";
reg = <0x66010000 0x28>;
--
2.1.0
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH 3/3] DT nodes for Broadcom Northstar2 USB DRD Phy
@ 2016-11-30 5:55 ` Raviteja Garimella
0 siblings, 0 replies; 20+ messages in thread
From: Raviteja Garimella @ 2016-11-30 5:55 UTC (permalink / raw)
To: linux-arm-kernel
This patch adds device tree nodes for USB Dual Role Device Phy for
Broadcom's Northstar2 SoC.
Signed-off-by: Raviteja Garimella <raviteja.garimella@broadcom.com>
---
arch/arm64/boot/dts/broadcom/ns2.dtsi | 14 ++++++++++++++
1 file changed, 14 insertions(+)
diff --git a/arch/arm64/boot/dts/broadcom/ns2.dtsi b/arch/arm64/boot/dts/broadcom/ns2.dtsi
index d95dc40..e9d3496 100644
--- a/arch/arm64/boot/dts/broadcom/ns2.dtsi
+++ b/arch/arm64/boot/dts/broadcom/ns2.dtsi
@@ -299,6 +299,20 @@
};
};
+ usbdrd_phy: phy at 66000960 {
+ #phy-cells = <0>;
+ compatible = "brcm,ns2-drd-phy";
+ reg = <0x66000960 0x24>,
+ <0x67012800 0x4>,
+ <0x6501d148 0x4>,
+ <0x664d0700 0x4>;
+ reg-names = "icfg", "rst-ctrl",
+ "crmu-ctrl", "usb2-strap";
+ id-gpios = <&gpio_g 30 0>;
+ vbus-gpios = <&gpio_g 31 0>;
+ status = "disabled";
+ };
+
pwm: pwm at 66010000 {
compatible = "brcm,iproc-pwm";
reg = <0x66010000 0x28>;
--
2.1.0
^ permalink raw reply related [flat|nested] 20+ messages in thread
* Re: [PATCH 1/3] Add DT bindings documentation for NS2 USB DRD phy
@ 2016-12-05 23:09 ` Rob Herring
0 siblings, 0 replies; 20+ messages in thread
From: Rob Herring @ 2016-12-05 23:09 UTC (permalink / raw)
To: Raviteja Garimella
Cc: Mark Rutland, Kishon Vijay Abraham I, Ray Jui, Scott Branden,
Jon Mason, Catalin Marinas, Will Deacon, devicetree,
linux-kernel, bcm-kernel-feedback-list, linux-arm-kernel
On Wed, Nov 30, 2016 at 11:25:36AM +0530, Raviteja Garimella wrote:
> This patch adds documentation for NS2 DRD Phy driver DT bindings
>
> Signed-off-by: Raviteja Garimella <raviteja.garimella@broadcom.com>
> ---
> .../devicetree/bindings/phy/brcm,ns2-drd-phy.txt | 40 ++++++++++++++++++++++
> 1 file changed, 40 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt
>
> diff --git a/Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt b/Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt
> new file mode 100644
> index 0000000..5857f99
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt
> @@ -0,0 +1,40 @@
> +BROADCOM NORTHSTAR2 USB2 (DUAL ROLE DEVICE) PHY
> +
> +Required properties:
> + - compatible: brcm,ns2-drd-phy
> + - reg: offset and length of the NS2 PHY related registers.
> + - reg-names
> + The below registers must be provided.
> + icfg - for DRD ICFG configurations
> + rst-ctrl - for DRD IDM reset
> + crmu-ctrl - for CRMU core vdd, PHY and PHY PLL reset
> + usb2-strap - for port over current polarity reversal
> + - #phy-cells: Must be 0. No args required.
> + - vbus-gpios: vbus gpio binding
> + - id-gpios: id gpio binding
> +
> +Refer to phy/phy-bindings.txt for the generic PHY binding properties
> +
> +Example:
> + gpio_g: gpio@660a0000 {
You don't really need to show gpio node for the example. Otherwise,
Acked-by: Rob Herring <robh@kernel.org>
Rob
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH 1/3] Add DT bindings documentation for NS2 USB DRD phy
@ 2016-12-05 23:09 ` Rob Herring
0 siblings, 0 replies; 20+ messages in thread
From: Rob Herring @ 2016-12-05 23:09 UTC (permalink / raw)
To: Raviteja Garimella
Cc: Mark Rutland, Kishon Vijay Abraham I, Ray Jui, Scott Branden,
Jon Mason, Catalin Marinas, Will Deacon,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
bcm-kernel-feedback-list-dY08KVG/lbpWk0Htik3J/w,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
On Wed, Nov 30, 2016 at 11:25:36AM +0530, Raviteja Garimella wrote:
> This patch adds documentation for NS2 DRD Phy driver DT bindings
>
> Signed-off-by: Raviteja Garimella <raviteja.garimella-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>
> ---
> .../devicetree/bindings/phy/brcm,ns2-drd-phy.txt | 40 ++++++++++++++++++++++
> 1 file changed, 40 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt
>
> diff --git a/Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt b/Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt
> new file mode 100644
> index 0000000..5857f99
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt
> @@ -0,0 +1,40 @@
> +BROADCOM NORTHSTAR2 USB2 (DUAL ROLE DEVICE) PHY
> +
> +Required properties:
> + - compatible: brcm,ns2-drd-phy
> + - reg: offset and length of the NS2 PHY related registers.
> + - reg-names
> + The below registers must be provided.
> + icfg - for DRD ICFG configurations
> + rst-ctrl - for DRD IDM reset
> + crmu-ctrl - for CRMU core vdd, PHY and PHY PLL reset
> + usb2-strap - for port over current polarity reversal
> + - #phy-cells: Must be 0. No args required.
> + - vbus-gpios: vbus gpio binding
> + - id-gpios: id gpio binding
> +
> +Refer to phy/phy-bindings.txt for the generic PHY binding properties
> +
> +Example:
> + gpio_g: gpio@660a0000 {
You don't really need to show gpio node for the example. Otherwise,
Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
Rob
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 20+ messages in thread
* [PATCH 1/3] Add DT bindings documentation for NS2 USB DRD phy
@ 2016-12-05 23:09 ` Rob Herring
0 siblings, 0 replies; 20+ messages in thread
From: Rob Herring @ 2016-12-05 23:09 UTC (permalink / raw)
To: linux-arm-kernel
On Wed, Nov 30, 2016 at 11:25:36AM +0530, Raviteja Garimella wrote:
> This patch adds documentation for NS2 DRD Phy driver DT bindings
>
> Signed-off-by: Raviteja Garimella <raviteja.garimella@broadcom.com>
> ---
> .../devicetree/bindings/phy/brcm,ns2-drd-phy.txt | 40 ++++++++++++++++++++++
> 1 file changed, 40 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt
>
> diff --git a/Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt b/Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt
> new file mode 100644
> index 0000000..5857f99
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt
> @@ -0,0 +1,40 @@
> +BROADCOM NORTHSTAR2 USB2 (DUAL ROLE DEVICE) PHY
> +
> +Required properties:
> + - compatible: brcm,ns2-drd-phy
> + - reg: offset and length of the NS2 PHY related registers.
> + - reg-names
> + The below registers must be provided.
> + icfg - for DRD ICFG configurations
> + rst-ctrl - for DRD IDM reset
> + crmu-ctrl - for CRMU core vdd, PHY and PHY PLL reset
> + usb2-strap - for port over current polarity reversal
> + - #phy-cells: Must be 0. No args required.
> + - vbus-gpios: vbus gpio binding
> + - id-gpios: id gpio binding
> +
> +Refer to phy/phy-bindings.txt for the generic PHY binding properties
> +
> +Example:
> + gpio_g: gpio at 660a0000 {
You don't really need to show gpio node for the example. Otherwise,
Acked-by: Rob Herring <robh@kernel.org>
Rob
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH 2/3] Broadcom USB DRD Phy driver for Northstar2
2016-11-30 5:55 ` Raviteja Garimella
(?)
@ 2017-01-16 9:22 ` Kishon Vijay Abraham I
-1 siblings, 0 replies; 20+ messages in thread
From: Kishon Vijay Abraham I @ 2017-01-16 9:22 UTC (permalink / raw)
To: Raviteja Garimella, Rob Herring, Mark Rutland, Ray Jui,
Scott Branden, Jon Mason, Catalin Marinas, Will Deacon
Cc: devicetree, linux-kernel, bcm-kernel-feedback-list, linux-arm-kernel
Hi,
On Wednesday 30 November 2016 11:25 AM, Raviteja Garimella wrote:
> This is driver for USB DRD Phy used in Broadcom's Northstar2
> SoC. The phy can be configured to be in Device mode or Host
> mode based on the type of cable connected to the port. The
> driver registers to extcon framework to get appropriate
> connect events for Host/Device cables connect/disconnect
> states based on VBUS and ID interrupts.
>
> Signed-off-by: Raviteja Garimella <raviteja.garimella@broadcom.com>
> ---
> drivers/phy/Kconfig | 13 +
> drivers/phy/Makefile | 1 +
> drivers/phy/phy-bcm-ns2-usbdrd.c | 587 +++++++++++++++++++++++++++++++++++++++
> 3 files changed, 601 insertions(+)
> create mode 100644 drivers/phy/phy-bcm-ns2-usbdrd.c
>
> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> index fe00f91..b3b6a73 100644
> --- a/drivers/phy/Kconfig
> +++ b/drivers/phy/Kconfig
> @@ -479,6 +479,19 @@ config PHY_CYGNUS_PCIE
> Enable this to support the Broadcom Cygnus PCIe PHY.
> If unsure, say N.
>
> +config PHY_NS2_USB_DRD
> + tristate "Broadcom Northstar2 USB DRD PHY support"
> + depends on OF && (ARCH_BCM_IPROC || COMPILE_TEST)
> + select GENERIC_PHY
> + select EXTCON
> + default ARCH_BCM_IPROC
> + help
> + Enable this to support the Broadcom Northstar2 USB DRD PHY.
> + This driver initializes the PHY in either HOST or DEVICE mode.
> + The host or device configuration is read from device tree.
> +
> + If unsure, say N.
> +
> source "drivers/phy/tegra/Kconfig"
>
> config PHY_NS2_PCIE
> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
> index a534cf5..b733ba2 100644
> --- a/drivers/phy/Makefile
> +++ b/drivers/phy/Makefile
> @@ -58,5 +58,6 @@ obj-$(CONFIG_PHY_TUSB1210) += phy-tusb1210.o
> obj-$(CONFIG_PHY_BRCM_SATA) += phy-brcm-sata.o
> obj-$(CONFIG_PHY_PISTACHIO_USB) += phy-pistachio-usb.o
> obj-$(CONFIG_PHY_CYGNUS_PCIE) += phy-bcm-cygnus-pcie.o
> +obj-$(CONFIG_PHY_NS2_USB_DRD) += phy-bcm-ns2-usbdrd.o
> obj-$(CONFIG_ARCH_TEGRA) += tegra/
> obj-$(CONFIG_PHY_NS2_PCIE) += phy-bcm-ns2-pcie.o
> diff --git a/drivers/phy/phy-bcm-ns2-usbdrd.c b/drivers/phy/phy-bcm-ns2-usbdrd.c
> new file mode 100644
> index 0000000..460040d
> --- /dev/null
> +++ b/drivers/phy/phy-bcm-ns2-usbdrd.c
> @@ -0,0 +1,587 @@
> +/*
> + * Copyright (C) 2016 Broadcom
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation version 2.
> + *
> + * This program is distributed "as is" WITHOUT ANY WARRANTY of any
> + * kind, whether express or implied; without even the implied warranty
> + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/delay.h>
> +#include <linux/extcon.h>
> +#include <linux/gpio.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/init.h>
> +#include <linux/interrupt.h>
> +#include <linux/io.h>
> +#include <linux/irq.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/phy/phy.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +#include <linux/slab.h>
> +#include <linux/workqueue.h>
> +
> +#define ICFG_DRD_AFE 0x0
> +#define ICFG_MISC_STAT 0x18
> +#define ICFG_DRD_P0CTL 0x1C
> +#define ICFG_STRAP_CTRL 0x20
> +#define ICFG_FSM_CTRL 0x24
> +
> +#define IDM_RST_BIT BIT(0)
> +#define AFE_CORERDY_VDDC BIT(18)
> +#define PHY_PLL_RESETB BIT(15)
> +#define PHY_RESETB BIT(14)
> +#define PHY_PLL_LOCK BIT(0)
> +
> +#define DRD_DEV_MODE BIT(20)
> +#define OHCI_OVRCUR_POL BIT(11)
> +#define ICFG_OFF_MODE BIT(6)
> +#define PLL_LOCK_RETRY 1000
> +
> +#define EVT_DEVICE 0
> +#define EVT_HOST 1
> +#define EVT_IDLE 2
> +
> +#define DRD_HOST_MODE (BIT(2) | BIT(3))
> +#define DRD_DEVICE_MODE (BIT(4) | BIT(5))
> +#define DRD_HOST_VAL 0x803
> +#define DRD_DEV_VAL 0x807
> +#define GPIO_DELAY 20
> +#define PHY_WQ_DELAY msecs_to_jiffies(600)
> +
> +struct ns2_phy_data;
> +struct ns2_phy_driver {
> + void __iomem *icfgdrd_regs;
> + void __iomem *idmdrd_rst_ctrl;
> + void __iomem *crmu_usb2_ctrl;
> + void __iomem *usb2h_strap_reg;
> + spinlock_t lock; /* spin lock for phy driver */
> + bool host_mode;
> + struct ns2_phy_data *data;
> + struct extcon_specific_cable_nb extcon_dev;
> + struct extcon_specific_cable_nb extcon_host;
> + struct notifier_block host_nb;
> + struct notifier_block dev_nb;
> + struct delayed_work conn_work;
> + struct extcon_dev *edev;
> + struct gpio_desc *vbus_gpiod;
> + struct gpio_desc *id_gpiod;
> + int id_irq;
> + int vbus_irq;
> + unsigned long debounce_jiffies;
> + struct delayed_work wq_extcon;
> +};
> +
> +struct ns2_phy_data {
> + struct ns2_phy_driver *driver;
> + struct phy *phy;
> + int new_state;
> + bool poweron;
> +};
> +
> +static const unsigned int usb_extcon_cable[] = {
> + EXTCON_USB,
> + EXTCON_USB_HOST,
> + EXTCON_NONE,
> +};
> +
> +static inline int pll_lock_stat(u32 usb_reg, int reg_mask,
> + struct ns2_phy_driver *driver)
> +{
> + int retry = PLL_LOCK_RETRY;
> + u32 val;
> +
> + do {
> + udelay(1);
> + val = readl(driver->icfgdrd_regs + usb_reg);
> + if (val & reg_mask)
> + return 0;
> + } while (--retry > 0);
> +
> + return -EBUSY;
> +}
> +
> +static int ns2_drd_phy_init(struct phy *phy)
> +{
> + struct ns2_phy_data *data = phy_get_drvdata(phy);
> + struct ns2_phy_driver *driver = data->driver;
> + unsigned long flags;
> + u32 val;
> +
> + spin_lock_irqsave(&driver->lock, flags);
> +
> + val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
> +
> + if (data->new_state == EVT_HOST) {
> + val &= ~DRD_DEVICE_MODE;
> + val |= DRD_HOST_MODE;
> + } else {
> + val &= ~DRD_HOST_MODE;
> + val |= DRD_DEVICE_MODE;
> + }
> + writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
> +
> + spin_unlock_irqrestore(&driver->lock, flags);
> + return 0;
> +}
> +
> +static int ns2_drd_phy_shutdown(struct phy *phy)
> +{
> + struct ns2_phy_data *data = phy_get_drvdata(phy);
> + struct ns2_phy_driver *driver = data->driver;
> + unsigned long flags;
> + u32 val;
> +
> + spin_lock_irqsave(&driver->lock, flags);
> + if (!data->poweron)
> + goto exit;
> +
> + val = readl(driver->crmu_usb2_ctrl);
> + val &= ~AFE_CORERDY_VDDC;
> + writel(val, driver->crmu_usb2_ctrl);
> +
> + driver->host_mode = 0;
> + val = readl(driver->crmu_usb2_ctrl);
> + val &= ~DRD_DEV_MODE;
> + writel(val, driver->crmu_usb2_ctrl);
> +
> + /* Disable Host and Device Mode */
> + val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
> + val &= ~(DRD_HOST_MODE | DRD_DEVICE_MODE | ICFG_OFF_MODE);
> + writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
> +
> + data->poweron = 0;
> +exit:
> + spin_unlock_irqrestore(&driver->lock, flags);
> + return 0;
> +}
> +
> +static int ns2_drd_phy_poweron(struct phy *phy)
> +{
> + struct ns2_phy_data *data = phy_get_drvdata(phy);
> + struct ns2_phy_driver *driver = data->driver;
> + u32 extcon_event = data->new_state;
> + unsigned long flags;
> + int ret;
> + u32 val;
> +
> + spin_lock_irqsave(&driver->lock, flags);
> + if (extcon_event == EVT_DEVICE) {
> + if (data->poweron)
> + goto exit;
> +
> + writel(DRD_DEV_VAL, driver->icfgdrd_regs + ICFG_DRD_P0CTL);
> +
> + val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
> + val &= ~(DRD_HOST_MODE | ICFG_OFF_MODE);
> + val |= DRD_DEVICE_MODE;
> + writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
> +
> + val = readl(driver->idmdrd_rst_ctrl);
> + val &= ~IDM_RST_BIT;
> + writel(val, driver->idmdrd_rst_ctrl);
> +
> + val = readl(driver->crmu_usb2_ctrl);
> + val |= (AFE_CORERDY_VDDC | DRD_DEV_MODE);
> + writel(val, driver->crmu_usb2_ctrl);
> +
> + /* Bring PHY and PHY_PLL out of Reset */
> + val = readl(driver->crmu_usb2_ctrl);
> + val |= (PHY_PLL_RESETB | PHY_RESETB);
> + writel(val, driver->crmu_usb2_ctrl);
> +
> + ret = pll_lock_stat(ICFG_MISC_STAT, PHY_PLL_LOCK, driver);
> + if (ret < 0) {
> + dev_err(&phy->dev, "Phy PLL lock failed\n");
> + goto err_shutdown;
> + }
> + } else {
> + if (data->poweron && driver->host_mode)
> + goto exit;
> +
> + writel(DRD_HOST_VAL, driver->icfgdrd_regs + ICFG_DRD_P0CTL);
> +
> + val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
> + val &= ~(DRD_DEVICE_MODE | ICFG_OFF_MODE);
> + val |= DRD_HOST_MODE;
> + writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
> +
> + val = readl(driver->crmu_usb2_ctrl);
> + val |= AFE_CORERDY_VDDC;
> + writel(val, driver->crmu_usb2_ctrl);
> +
> + ret = pll_lock_stat(ICFG_MISC_STAT, PHY_PLL_LOCK, driver);
> + if (ret < 0) {
> + dev_err(&phy->dev, "Phy PLL lock failed\n");
> + goto err_shutdown;
> + }
> +
> + val = readl(driver->idmdrd_rst_ctrl);
> + val &= ~IDM_RST_BIT;
> + writel(val, driver->idmdrd_rst_ctrl);
> +
> + /* port over current Polarity */
> + val = readl(driver->usb2h_strap_reg);
> + val |= OHCI_OVRCUR_POL;
> + writel(val, driver->usb2h_strap_reg);
> +
> + driver->host_mode = 1;
> + }
> +
> + data->poweron = 1;
> +exit:
> + spin_unlock_irqrestore(&driver->lock, flags);
> + return 0;
> +
> +err_shutdown:
> + data->poweron = 1;
> + spin_unlock_irqrestore(&driver->lock, flags);
> + ns2_drd_phy_shutdown(phy);
> + return ret;
> +}
> +
> +static void connect_work(struct work_struct *work)
> +{
> + struct ns2_phy_driver *driver;
> + struct ns2_phy_data *data;
> + u32 extcon_event;
> +
> + driver = container_of(to_delayed_work(work),
> + struct ns2_phy_driver, conn_work);
> + data = driver->data;
> + extcon_event = data->new_state;
> +
> + if (extcon_event == EVT_DEVICE || extcon_event == EVT_HOST) {
> + ns2_drd_phy_init(data->phy);
> + ns2_drd_phy_poweron(data->phy);
> + } else if (extcon_event == EVT_IDLE) {
> + ns2_drd_phy_shutdown(data->phy);
> + }
> +}
> +
> +static int drd_device_notify(struct notifier_block *self,
> + unsigned long event, void *ptr)
> +{
> + struct ns2_phy_driver *driver = container_of(self,
> + struct ns2_phy_driver, dev_nb);
> +
> + if (event) {
> + pr_debug("Device connected\n");
> + driver->data->new_state = EVT_DEVICE;
> + schedule_delayed_work(&driver->conn_work, 0);
> + } else {
> + pr_debug("Device disconnected\n");
> + driver->data->new_state = EVT_IDLE;
> + schedule_delayed_work(&driver->conn_work, PHY_WQ_DELAY);
> + }
> +
> + return NOTIFY_DONE;
> +}
> +
> +static int drd_host_notify(struct notifier_block *self,
> + unsigned long event, void *ptr)
> +{
> + struct ns2_phy_driver *driver = container_of(self,
> + struct ns2_phy_driver, host_nb);
> +
> + if (event) {
> + pr_debug("Host connected\n");
> + driver->data->new_state = EVT_HOST;
> + schedule_delayed_work(&driver->conn_work, 0);
> + } else {
> + pr_debug("Host disconnected\n");
> + driver->data->new_state = EVT_IDLE;
> + schedule_delayed_work(&driver->conn_work, PHY_WQ_DELAY);
> + }
> +
> + return NOTIFY_DONE;
> +}
> +
> +static void extcon_work(struct work_struct *work)
> +{
> + struct ns2_phy_driver *driver;
> + int vbus;
> + int id;
> +
> + driver = container_of(to_delayed_work(work),
> + struct ns2_phy_driver, wq_extcon);
> +
> + id = gpiod_get_value_cansleep(driver->id_gpiod);
> + vbus = gpiod_get_value_cansleep(driver->vbus_gpiod);
> +
> + if (!id && vbus) {
> + extcon_set_cable_state_(driver->edev, EXTCON_USB_HOST, true);
> + } else if (id && !vbus) {
> + extcon_set_cable_state_(driver->edev, EXTCON_USB_HOST, false);
> + extcon_set_cable_state_(driver->edev, EXTCON_USB, false);
> + } else if (id && vbus) {
> + extcon_set_cable_state_(driver->edev, EXTCON_USB, true);
> + }
> +}
> +
> +static irqreturn_t gpio_irq_handler(int irq, void *dev_id)
> +{
> + struct ns2_phy_driver *driver = dev_id;
> +
> + queue_delayed_work(system_power_efficient_wq, &driver->wq_extcon,
> + driver->debounce_jiffies);
> +
> + return IRQ_HANDLED;
> +}
> +
> +static int register_extcon_notifier(struct ns2_phy_driver *phy_driver,
> + struct device *dev)
> +{
> + struct extcon_dev *edev;
> + int ret;
> +
> + phy_driver->host_nb.notifier_call = drd_host_notify;
> + phy_driver->dev_nb.notifier_call = drd_device_notify;
> +
> + edev = phy_driver->edev;
> +
> + /* Register for device change notification */
> + ret = extcon_register_notifier(edev, EXTCON_USB,
> + &phy_driver->dev_nb);
> + if (ret < 0) {
> + dev_err(dev, "can't register extcon_dev for %s\n", edev->name);
> + return ret;
> + }
> +
> + /* Register for host change notification */
> + ret = extcon_register_notifier(edev, EXTCON_USB_HOST,
> + &phy_driver->host_nb);
> + if (ret < 0) {
> + dev_err(dev, "can't register extcon_dev for %s\n", edev->name);
> + goto err_dev;
> + }
> +
> + /* Check the device cable connect state */
> + ret = extcon_get_cable_state_(edev, EXTCON_USB);
> + if (ret < 0) {
> + dev_err(dev, "can't get extcon_dev state for %s\n", edev->name);
> + goto err_host;
> + } else if (ret) {
> + phy_driver->data->new_state = EVT_DEVICE;
> + }
> +
> + /* Check the host cable connect state */
> + ret = extcon_get_cable_state_(edev, EXTCON_USB_HOST);
> + if (ret < 0) {
> + dev_err(dev, "can't get extcon_dev state for %s\n", edev->name);
> + goto err_host;
> + } else if (ret) {
> + phy_driver->data->new_state = EVT_HOST;
> + }
> +
> + return 0;
> +
> +err_host:
> + ret = extcon_unregister_notifier(edev, EXTCON_USB_HOST,
> + &phy_driver->host_nb);
> +err_dev:
> + ret = extcon_unregister_notifier(edev, EXTCON_USB,
> + &phy_driver->dev_nb);
> + return ret;
> +}
> +
> +static struct phy_ops ops = {
> + .init = ns2_drd_phy_init,
Is this really being used by any controller driver? Can you point me to the
controller driver that is using this driver?
> + .power_on = ns2_drd_phy_poweron,
> + .power_off = ns2_drd_phy_shutdown,
missing .owner.
Thanks
Kishon
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH 2/3] Broadcom USB DRD Phy driver for Northstar2
@ 2017-01-16 9:22 ` Kishon Vijay Abraham I
0 siblings, 0 replies; 20+ messages in thread
From: Kishon Vijay Abraham I @ 2017-01-16 9:22 UTC (permalink / raw)
To: Raviteja Garimella, Rob Herring, Mark Rutland, Ray Jui,
Scott Branden, Jon Mason, Catalin Marinas, Will Deacon
Cc: devicetree, bcm-kernel-feedback-list, linux-kernel, linux-arm-kernel
Hi,
On Wednesday 30 November 2016 11:25 AM, Raviteja Garimella wrote:
> This is driver for USB DRD Phy used in Broadcom's Northstar2
> SoC. The phy can be configured to be in Device mode or Host
> mode based on the type of cable connected to the port. The
> driver registers to extcon framework to get appropriate
> connect events for Host/Device cables connect/disconnect
> states based on VBUS and ID interrupts.
>
> Signed-off-by: Raviteja Garimella <raviteja.garimella@broadcom.com>
> ---
> drivers/phy/Kconfig | 13 +
> drivers/phy/Makefile | 1 +
> drivers/phy/phy-bcm-ns2-usbdrd.c | 587 +++++++++++++++++++++++++++++++++++++++
> 3 files changed, 601 insertions(+)
> create mode 100644 drivers/phy/phy-bcm-ns2-usbdrd.c
>
> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> index fe00f91..b3b6a73 100644
> --- a/drivers/phy/Kconfig
> +++ b/drivers/phy/Kconfig
> @@ -479,6 +479,19 @@ config PHY_CYGNUS_PCIE
> Enable this to support the Broadcom Cygnus PCIe PHY.
> If unsure, say N.
>
> +config PHY_NS2_USB_DRD
> + tristate "Broadcom Northstar2 USB DRD PHY support"
> + depends on OF && (ARCH_BCM_IPROC || COMPILE_TEST)
> + select GENERIC_PHY
> + select EXTCON
> + default ARCH_BCM_IPROC
> + help
> + Enable this to support the Broadcom Northstar2 USB DRD PHY.
> + This driver initializes the PHY in either HOST or DEVICE mode.
> + The host or device configuration is read from device tree.
> +
> + If unsure, say N.
> +
> source "drivers/phy/tegra/Kconfig"
>
> config PHY_NS2_PCIE
> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
> index a534cf5..b733ba2 100644
> --- a/drivers/phy/Makefile
> +++ b/drivers/phy/Makefile
> @@ -58,5 +58,6 @@ obj-$(CONFIG_PHY_TUSB1210) += phy-tusb1210.o
> obj-$(CONFIG_PHY_BRCM_SATA) += phy-brcm-sata.o
> obj-$(CONFIG_PHY_PISTACHIO_USB) += phy-pistachio-usb.o
> obj-$(CONFIG_PHY_CYGNUS_PCIE) += phy-bcm-cygnus-pcie.o
> +obj-$(CONFIG_PHY_NS2_USB_DRD) += phy-bcm-ns2-usbdrd.o
> obj-$(CONFIG_ARCH_TEGRA) += tegra/
> obj-$(CONFIG_PHY_NS2_PCIE) += phy-bcm-ns2-pcie.o
> diff --git a/drivers/phy/phy-bcm-ns2-usbdrd.c b/drivers/phy/phy-bcm-ns2-usbdrd.c
> new file mode 100644
> index 0000000..460040d
> --- /dev/null
> +++ b/drivers/phy/phy-bcm-ns2-usbdrd.c
> @@ -0,0 +1,587 @@
> +/*
> + * Copyright (C) 2016 Broadcom
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation version 2.
> + *
> + * This program is distributed "as is" WITHOUT ANY WARRANTY of any
> + * kind, whether express or implied; without even the implied warranty
> + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/delay.h>
> +#include <linux/extcon.h>
> +#include <linux/gpio.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/init.h>
> +#include <linux/interrupt.h>
> +#include <linux/io.h>
> +#include <linux/irq.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/phy/phy.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +#include <linux/slab.h>
> +#include <linux/workqueue.h>
> +
> +#define ICFG_DRD_AFE 0x0
> +#define ICFG_MISC_STAT 0x18
> +#define ICFG_DRD_P0CTL 0x1C
> +#define ICFG_STRAP_CTRL 0x20
> +#define ICFG_FSM_CTRL 0x24
> +
> +#define IDM_RST_BIT BIT(0)
> +#define AFE_CORERDY_VDDC BIT(18)
> +#define PHY_PLL_RESETB BIT(15)
> +#define PHY_RESETB BIT(14)
> +#define PHY_PLL_LOCK BIT(0)
> +
> +#define DRD_DEV_MODE BIT(20)
> +#define OHCI_OVRCUR_POL BIT(11)
> +#define ICFG_OFF_MODE BIT(6)
> +#define PLL_LOCK_RETRY 1000
> +
> +#define EVT_DEVICE 0
> +#define EVT_HOST 1
> +#define EVT_IDLE 2
> +
> +#define DRD_HOST_MODE (BIT(2) | BIT(3))
> +#define DRD_DEVICE_MODE (BIT(4) | BIT(5))
> +#define DRD_HOST_VAL 0x803
> +#define DRD_DEV_VAL 0x807
> +#define GPIO_DELAY 20
> +#define PHY_WQ_DELAY msecs_to_jiffies(600)
> +
> +struct ns2_phy_data;
> +struct ns2_phy_driver {
> + void __iomem *icfgdrd_regs;
> + void __iomem *idmdrd_rst_ctrl;
> + void __iomem *crmu_usb2_ctrl;
> + void __iomem *usb2h_strap_reg;
> + spinlock_t lock; /* spin lock for phy driver */
> + bool host_mode;
> + struct ns2_phy_data *data;
> + struct extcon_specific_cable_nb extcon_dev;
> + struct extcon_specific_cable_nb extcon_host;
> + struct notifier_block host_nb;
> + struct notifier_block dev_nb;
> + struct delayed_work conn_work;
> + struct extcon_dev *edev;
> + struct gpio_desc *vbus_gpiod;
> + struct gpio_desc *id_gpiod;
> + int id_irq;
> + int vbus_irq;
> + unsigned long debounce_jiffies;
> + struct delayed_work wq_extcon;
> +};
> +
> +struct ns2_phy_data {
> + struct ns2_phy_driver *driver;
> + struct phy *phy;
> + int new_state;
> + bool poweron;
> +};
> +
> +static const unsigned int usb_extcon_cable[] = {
> + EXTCON_USB,
> + EXTCON_USB_HOST,
> + EXTCON_NONE,
> +};
> +
> +static inline int pll_lock_stat(u32 usb_reg, int reg_mask,
> + struct ns2_phy_driver *driver)
> +{
> + int retry = PLL_LOCK_RETRY;
> + u32 val;
> +
> + do {
> + udelay(1);
> + val = readl(driver->icfgdrd_regs + usb_reg);
> + if (val & reg_mask)
> + return 0;
> + } while (--retry > 0);
> +
> + return -EBUSY;
> +}
> +
> +static int ns2_drd_phy_init(struct phy *phy)
> +{
> + struct ns2_phy_data *data = phy_get_drvdata(phy);
> + struct ns2_phy_driver *driver = data->driver;
> + unsigned long flags;
> + u32 val;
> +
> + spin_lock_irqsave(&driver->lock, flags);
> +
> + val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
> +
> + if (data->new_state == EVT_HOST) {
> + val &= ~DRD_DEVICE_MODE;
> + val |= DRD_HOST_MODE;
> + } else {
> + val &= ~DRD_HOST_MODE;
> + val |= DRD_DEVICE_MODE;
> + }
> + writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
> +
> + spin_unlock_irqrestore(&driver->lock, flags);
> + return 0;
> +}
> +
> +static int ns2_drd_phy_shutdown(struct phy *phy)
> +{
> + struct ns2_phy_data *data = phy_get_drvdata(phy);
> + struct ns2_phy_driver *driver = data->driver;
> + unsigned long flags;
> + u32 val;
> +
> + spin_lock_irqsave(&driver->lock, flags);
> + if (!data->poweron)
> + goto exit;
> +
> + val = readl(driver->crmu_usb2_ctrl);
> + val &= ~AFE_CORERDY_VDDC;
> + writel(val, driver->crmu_usb2_ctrl);
> +
> + driver->host_mode = 0;
> + val = readl(driver->crmu_usb2_ctrl);
> + val &= ~DRD_DEV_MODE;
> + writel(val, driver->crmu_usb2_ctrl);
> +
> + /* Disable Host and Device Mode */
> + val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
> + val &= ~(DRD_HOST_MODE | DRD_DEVICE_MODE | ICFG_OFF_MODE);
> + writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
> +
> + data->poweron = 0;
> +exit:
> + spin_unlock_irqrestore(&driver->lock, flags);
> + return 0;
> +}
> +
> +static int ns2_drd_phy_poweron(struct phy *phy)
> +{
> + struct ns2_phy_data *data = phy_get_drvdata(phy);
> + struct ns2_phy_driver *driver = data->driver;
> + u32 extcon_event = data->new_state;
> + unsigned long flags;
> + int ret;
> + u32 val;
> +
> + spin_lock_irqsave(&driver->lock, flags);
> + if (extcon_event == EVT_DEVICE) {
> + if (data->poweron)
> + goto exit;
> +
> + writel(DRD_DEV_VAL, driver->icfgdrd_regs + ICFG_DRD_P0CTL);
> +
> + val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
> + val &= ~(DRD_HOST_MODE | ICFG_OFF_MODE);
> + val |= DRD_DEVICE_MODE;
> + writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
> +
> + val = readl(driver->idmdrd_rst_ctrl);
> + val &= ~IDM_RST_BIT;
> + writel(val, driver->idmdrd_rst_ctrl);
> +
> + val = readl(driver->crmu_usb2_ctrl);
> + val |= (AFE_CORERDY_VDDC | DRD_DEV_MODE);
> + writel(val, driver->crmu_usb2_ctrl);
> +
> + /* Bring PHY and PHY_PLL out of Reset */
> + val = readl(driver->crmu_usb2_ctrl);
> + val |= (PHY_PLL_RESETB | PHY_RESETB);
> + writel(val, driver->crmu_usb2_ctrl);
> +
> + ret = pll_lock_stat(ICFG_MISC_STAT, PHY_PLL_LOCK, driver);
> + if (ret < 0) {
> + dev_err(&phy->dev, "Phy PLL lock failed\n");
> + goto err_shutdown;
> + }
> + } else {
> + if (data->poweron && driver->host_mode)
> + goto exit;
> +
> + writel(DRD_HOST_VAL, driver->icfgdrd_regs + ICFG_DRD_P0CTL);
> +
> + val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
> + val &= ~(DRD_DEVICE_MODE | ICFG_OFF_MODE);
> + val |= DRD_HOST_MODE;
> + writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
> +
> + val = readl(driver->crmu_usb2_ctrl);
> + val |= AFE_CORERDY_VDDC;
> + writel(val, driver->crmu_usb2_ctrl);
> +
> + ret = pll_lock_stat(ICFG_MISC_STAT, PHY_PLL_LOCK, driver);
> + if (ret < 0) {
> + dev_err(&phy->dev, "Phy PLL lock failed\n");
> + goto err_shutdown;
> + }
> +
> + val = readl(driver->idmdrd_rst_ctrl);
> + val &= ~IDM_RST_BIT;
> + writel(val, driver->idmdrd_rst_ctrl);
> +
> + /* port over current Polarity */
> + val = readl(driver->usb2h_strap_reg);
> + val |= OHCI_OVRCUR_POL;
> + writel(val, driver->usb2h_strap_reg);
> +
> + driver->host_mode = 1;
> + }
> +
> + data->poweron = 1;
> +exit:
> + spin_unlock_irqrestore(&driver->lock, flags);
> + return 0;
> +
> +err_shutdown:
> + data->poweron = 1;
> + spin_unlock_irqrestore(&driver->lock, flags);
> + ns2_drd_phy_shutdown(phy);
> + return ret;
> +}
> +
> +static void connect_work(struct work_struct *work)
> +{
> + struct ns2_phy_driver *driver;
> + struct ns2_phy_data *data;
> + u32 extcon_event;
> +
> + driver = container_of(to_delayed_work(work),
> + struct ns2_phy_driver, conn_work);
> + data = driver->data;
> + extcon_event = data->new_state;
> +
> + if (extcon_event == EVT_DEVICE || extcon_event == EVT_HOST) {
> + ns2_drd_phy_init(data->phy);
> + ns2_drd_phy_poweron(data->phy);
> + } else if (extcon_event == EVT_IDLE) {
> + ns2_drd_phy_shutdown(data->phy);
> + }
> +}
> +
> +static int drd_device_notify(struct notifier_block *self,
> + unsigned long event, void *ptr)
> +{
> + struct ns2_phy_driver *driver = container_of(self,
> + struct ns2_phy_driver, dev_nb);
> +
> + if (event) {
> + pr_debug("Device connected\n");
> + driver->data->new_state = EVT_DEVICE;
> + schedule_delayed_work(&driver->conn_work, 0);
> + } else {
> + pr_debug("Device disconnected\n");
> + driver->data->new_state = EVT_IDLE;
> + schedule_delayed_work(&driver->conn_work, PHY_WQ_DELAY);
> + }
> +
> + return NOTIFY_DONE;
> +}
> +
> +static int drd_host_notify(struct notifier_block *self,
> + unsigned long event, void *ptr)
> +{
> + struct ns2_phy_driver *driver = container_of(self,
> + struct ns2_phy_driver, host_nb);
> +
> + if (event) {
> + pr_debug("Host connected\n");
> + driver->data->new_state = EVT_HOST;
> + schedule_delayed_work(&driver->conn_work, 0);
> + } else {
> + pr_debug("Host disconnected\n");
> + driver->data->new_state = EVT_IDLE;
> + schedule_delayed_work(&driver->conn_work, PHY_WQ_DELAY);
> + }
> +
> + return NOTIFY_DONE;
> +}
> +
> +static void extcon_work(struct work_struct *work)
> +{
> + struct ns2_phy_driver *driver;
> + int vbus;
> + int id;
> +
> + driver = container_of(to_delayed_work(work),
> + struct ns2_phy_driver, wq_extcon);
> +
> + id = gpiod_get_value_cansleep(driver->id_gpiod);
> + vbus = gpiod_get_value_cansleep(driver->vbus_gpiod);
> +
> + if (!id && vbus) {
> + extcon_set_cable_state_(driver->edev, EXTCON_USB_HOST, true);
> + } else if (id && !vbus) {
> + extcon_set_cable_state_(driver->edev, EXTCON_USB_HOST, false);
> + extcon_set_cable_state_(driver->edev, EXTCON_USB, false);
> + } else if (id && vbus) {
> + extcon_set_cable_state_(driver->edev, EXTCON_USB, true);
> + }
> +}
> +
> +static irqreturn_t gpio_irq_handler(int irq, void *dev_id)
> +{
> + struct ns2_phy_driver *driver = dev_id;
> +
> + queue_delayed_work(system_power_efficient_wq, &driver->wq_extcon,
> + driver->debounce_jiffies);
> +
> + return IRQ_HANDLED;
> +}
> +
> +static int register_extcon_notifier(struct ns2_phy_driver *phy_driver,
> + struct device *dev)
> +{
> + struct extcon_dev *edev;
> + int ret;
> +
> + phy_driver->host_nb.notifier_call = drd_host_notify;
> + phy_driver->dev_nb.notifier_call = drd_device_notify;
> +
> + edev = phy_driver->edev;
> +
> + /* Register for device change notification */
> + ret = extcon_register_notifier(edev, EXTCON_USB,
> + &phy_driver->dev_nb);
> + if (ret < 0) {
> + dev_err(dev, "can't register extcon_dev for %s\n", edev->name);
> + return ret;
> + }
> +
> + /* Register for host change notification */
> + ret = extcon_register_notifier(edev, EXTCON_USB_HOST,
> + &phy_driver->host_nb);
> + if (ret < 0) {
> + dev_err(dev, "can't register extcon_dev for %s\n", edev->name);
> + goto err_dev;
> + }
> +
> + /* Check the device cable connect state */
> + ret = extcon_get_cable_state_(edev, EXTCON_USB);
> + if (ret < 0) {
> + dev_err(dev, "can't get extcon_dev state for %s\n", edev->name);
> + goto err_host;
> + } else if (ret) {
> + phy_driver->data->new_state = EVT_DEVICE;
> + }
> +
> + /* Check the host cable connect state */
> + ret = extcon_get_cable_state_(edev, EXTCON_USB_HOST);
> + if (ret < 0) {
> + dev_err(dev, "can't get extcon_dev state for %s\n", edev->name);
> + goto err_host;
> + } else if (ret) {
> + phy_driver->data->new_state = EVT_HOST;
> + }
> +
> + return 0;
> +
> +err_host:
> + ret = extcon_unregister_notifier(edev, EXTCON_USB_HOST,
> + &phy_driver->host_nb);
> +err_dev:
> + ret = extcon_unregister_notifier(edev, EXTCON_USB,
> + &phy_driver->dev_nb);
> + return ret;
> +}
> +
> +static struct phy_ops ops = {
> + .init = ns2_drd_phy_init,
Is this really being used by any controller driver? Can you point me to the
controller driver that is using this driver?
> + .power_on = ns2_drd_phy_poweron,
> + .power_off = ns2_drd_phy_shutdown,
missing .owner.
Thanks
Kishon
^ permalink raw reply [flat|nested] 20+ messages in thread
* [PATCH 2/3] Broadcom USB DRD Phy driver for Northstar2
@ 2017-01-16 9:22 ` Kishon Vijay Abraham I
0 siblings, 0 replies; 20+ messages in thread
From: Kishon Vijay Abraham I @ 2017-01-16 9:22 UTC (permalink / raw)
To: linux-arm-kernel
Hi,
On Wednesday 30 November 2016 11:25 AM, Raviteja Garimella wrote:
> This is driver for USB DRD Phy used in Broadcom's Northstar2
> SoC. The phy can be configured to be in Device mode or Host
> mode based on the type of cable connected to the port. The
> driver registers to extcon framework to get appropriate
> connect events for Host/Device cables connect/disconnect
> states based on VBUS and ID interrupts.
>
> Signed-off-by: Raviteja Garimella <raviteja.garimella@broadcom.com>
> ---
> drivers/phy/Kconfig | 13 +
> drivers/phy/Makefile | 1 +
> drivers/phy/phy-bcm-ns2-usbdrd.c | 587 +++++++++++++++++++++++++++++++++++++++
> 3 files changed, 601 insertions(+)
> create mode 100644 drivers/phy/phy-bcm-ns2-usbdrd.c
>
> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> index fe00f91..b3b6a73 100644
> --- a/drivers/phy/Kconfig
> +++ b/drivers/phy/Kconfig
> @@ -479,6 +479,19 @@ config PHY_CYGNUS_PCIE
> Enable this to support the Broadcom Cygnus PCIe PHY.
> If unsure, say N.
>
> +config PHY_NS2_USB_DRD
> + tristate "Broadcom Northstar2 USB DRD PHY support"
> + depends on OF && (ARCH_BCM_IPROC || COMPILE_TEST)
> + select GENERIC_PHY
> + select EXTCON
> + default ARCH_BCM_IPROC
> + help
> + Enable this to support the Broadcom Northstar2 USB DRD PHY.
> + This driver initializes the PHY in either HOST or DEVICE mode.
> + The host or device configuration is read from device tree.
> +
> + If unsure, say N.
> +
> source "drivers/phy/tegra/Kconfig"
>
> config PHY_NS2_PCIE
> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
> index a534cf5..b733ba2 100644
> --- a/drivers/phy/Makefile
> +++ b/drivers/phy/Makefile
> @@ -58,5 +58,6 @@ obj-$(CONFIG_PHY_TUSB1210) += phy-tusb1210.o
> obj-$(CONFIG_PHY_BRCM_SATA) += phy-brcm-sata.o
> obj-$(CONFIG_PHY_PISTACHIO_USB) += phy-pistachio-usb.o
> obj-$(CONFIG_PHY_CYGNUS_PCIE) += phy-bcm-cygnus-pcie.o
> +obj-$(CONFIG_PHY_NS2_USB_DRD) += phy-bcm-ns2-usbdrd.o
> obj-$(CONFIG_ARCH_TEGRA) += tegra/
> obj-$(CONFIG_PHY_NS2_PCIE) += phy-bcm-ns2-pcie.o
> diff --git a/drivers/phy/phy-bcm-ns2-usbdrd.c b/drivers/phy/phy-bcm-ns2-usbdrd.c
> new file mode 100644
> index 0000000..460040d
> --- /dev/null
> +++ b/drivers/phy/phy-bcm-ns2-usbdrd.c
> @@ -0,0 +1,587 @@
> +/*
> + * Copyright (C) 2016 Broadcom
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation version 2.
> + *
> + * This program is distributed "as is" WITHOUT ANY WARRANTY of any
> + * kind, whether express or implied; without even the implied warranty
> + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/delay.h>
> +#include <linux/extcon.h>
> +#include <linux/gpio.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/init.h>
> +#include <linux/interrupt.h>
> +#include <linux/io.h>
> +#include <linux/irq.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/phy/phy.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +#include <linux/slab.h>
> +#include <linux/workqueue.h>
> +
> +#define ICFG_DRD_AFE 0x0
> +#define ICFG_MISC_STAT 0x18
> +#define ICFG_DRD_P0CTL 0x1C
> +#define ICFG_STRAP_CTRL 0x20
> +#define ICFG_FSM_CTRL 0x24
> +
> +#define IDM_RST_BIT BIT(0)
> +#define AFE_CORERDY_VDDC BIT(18)
> +#define PHY_PLL_RESETB BIT(15)
> +#define PHY_RESETB BIT(14)
> +#define PHY_PLL_LOCK BIT(0)
> +
> +#define DRD_DEV_MODE BIT(20)
> +#define OHCI_OVRCUR_POL BIT(11)
> +#define ICFG_OFF_MODE BIT(6)
> +#define PLL_LOCK_RETRY 1000
> +
> +#define EVT_DEVICE 0
> +#define EVT_HOST 1
> +#define EVT_IDLE 2
> +
> +#define DRD_HOST_MODE (BIT(2) | BIT(3))
> +#define DRD_DEVICE_MODE (BIT(4) | BIT(5))
> +#define DRD_HOST_VAL 0x803
> +#define DRD_DEV_VAL 0x807
> +#define GPIO_DELAY 20
> +#define PHY_WQ_DELAY msecs_to_jiffies(600)
> +
> +struct ns2_phy_data;
> +struct ns2_phy_driver {
> + void __iomem *icfgdrd_regs;
> + void __iomem *idmdrd_rst_ctrl;
> + void __iomem *crmu_usb2_ctrl;
> + void __iomem *usb2h_strap_reg;
> + spinlock_t lock; /* spin lock for phy driver */
> + bool host_mode;
> + struct ns2_phy_data *data;
> + struct extcon_specific_cable_nb extcon_dev;
> + struct extcon_specific_cable_nb extcon_host;
> + struct notifier_block host_nb;
> + struct notifier_block dev_nb;
> + struct delayed_work conn_work;
> + struct extcon_dev *edev;
> + struct gpio_desc *vbus_gpiod;
> + struct gpio_desc *id_gpiod;
> + int id_irq;
> + int vbus_irq;
> + unsigned long debounce_jiffies;
> + struct delayed_work wq_extcon;
> +};
> +
> +struct ns2_phy_data {
> + struct ns2_phy_driver *driver;
> + struct phy *phy;
> + int new_state;
> + bool poweron;
> +};
> +
> +static const unsigned int usb_extcon_cable[] = {
> + EXTCON_USB,
> + EXTCON_USB_HOST,
> + EXTCON_NONE,
> +};
> +
> +static inline int pll_lock_stat(u32 usb_reg, int reg_mask,
> + struct ns2_phy_driver *driver)
> +{
> + int retry = PLL_LOCK_RETRY;
> + u32 val;
> +
> + do {
> + udelay(1);
> + val = readl(driver->icfgdrd_regs + usb_reg);
> + if (val & reg_mask)
> + return 0;
> + } while (--retry > 0);
> +
> + return -EBUSY;
> +}
> +
> +static int ns2_drd_phy_init(struct phy *phy)
> +{
> + struct ns2_phy_data *data = phy_get_drvdata(phy);
> + struct ns2_phy_driver *driver = data->driver;
> + unsigned long flags;
> + u32 val;
> +
> + spin_lock_irqsave(&driver->lock, flags);
> +
> + val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
> +
> + if (data->new_state == EVT_HOST) {
> + val &= ~DRD_DEVICE_MODE;
> + val |= DRD_HOST_MODE;
> + } else {
> + val &= ~DRD_HOST_MODE;
> + val |= DRD_DEVICE_MODE;
> + }
> + writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
> +
> + spin_unlock_irqrestore(&driver->lock, flags);
> + return 0;
> +}
> +
> +static int ns2_drd_phy_shutdown(struct phy *phy)
> +{
> + struct ns2_phy_data *data = phy_get_drvdata(phy);
> + struct ns2_phy_driver *driver = data->driver;
> + unsigned long flags;
> + u32 val;
> +
> + spin_lock_irqsave(&driver->lock, flags);
> + if (!data->poweron)
> + goto exit;
> +
> + val = readl(driver->crmu_usb2_ctrl);
> + val &= ~AFE_CORERDY_VDDC;
> + writel(val, driver->crmu_usb2_ctrl);
> +
> + driver->host_mode = 0;
> + val = readl(driver->crmu_usb2_ctrl);
> + val &= ~DRD_DEV_MODE;
> + writel(val, driver->crmu_usb2_ctrl);
> +
> + /* Disable Host and Device Mode */
> + val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
> + val &= ~(DRD_HOST_MODE | DRD_DEVICE_MODE | ICFG_OFF_MODE);
> + writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
> +
> + data->poweron = 0;
> +exit:
> + spin_unlock_irqrestore(&driver->lock, flags);
> + return 0;
> +}
> +
> +static int ns2_drd_phy_poweron(struct phy *phy)
> +{
> + struct ns2_phy_data *data = phy_get_drvdata(phy);
> + struct ns2_phy_driver *driver = data->driver;
> + u32 extcon_event = data->new_state;
> + unsigned long flags;
> + int ret;
> + u32 val;
> +
> + spin_lock_irqsave(&driver->lock, flags);
> + if (extcon_event == EVT_DEVICE) {
> + if (data->poweron)
> + goto exit;
> +
> + writel(DRD_DEV_VAL, driver->icfgdrd_regs + ICFG_DRD_P0CTL);
> +
> + val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
> + val &= ~(DRD_HOST_MODE | ICFG_OFF_MODE);
> + val |= DRD_DEVICE_MODE;
> + writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
> +
> + val = readl(driver->idmdrd_rst_ctrl);
> + val &= ~IDM_RST_BIT;
> + writel(val, driver->idmdrd_rst_ctrl);
> +
> + val = readl(driver->crmu_usb2_ctrl);
> + val |= (AFE_CORERDY_VDDC | DRD_DEV_MODE);
> + writel(val, driver->crmu_usb2_ctrl);
> +
> + /* Bring PHY and PHY_PLL out of Reset */
> + val = readl(driver->crmu_usb2_ctrl);
> + val |= (PHY_PLL_RESETB | PHY_RESETB);
> + writel(val, driver->crmu_usb2_ctrl);
> +
> + ret = pll_lock_stat(ICFG_MISC_STAT, PHY_PLL_LOCK, driver);
> + if (ret < 0) {
> + dev_err(&phy->dev, "Phy PLL lock failed\n");
> + goto err_shutdown;
> + }
> + } else {
> + if (data->poweron && driver->host_mode)
> + goto exit;
> +
> + writel(DRD_HOST_VAL, driver->icfgdrd_regs + ICFG_DRD_P0CTL);
> +
> + val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
> + val &= ~(DRD_DEVICE_MODE | ICFG_OFF_MODE);
> + val |= DRD_HOST_MODE;
> + writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
> +
> + val = readl(driver->crmu_usb2_ctrl);
> + val |= AFE_CORERDY_VDDC;
> + writel(val, driver->crmu_usb2_ctrl);
> +
> + ret = pll_lock_stat(ICFG_MISC_STAT, PHY_PLL_LOCK, driver);
> + if (ret < 0) {
> + dev_err(&phy->dev, "Phy PLL lock failed\n");
> + goto err_shutdown;
> + }
> +
> + val = readl(driver->idmdrd_rst_ctrl);
> + val &= ~IDM_RST_BIT;
> + writel(val, driver->idmdrd_rst_ctrl);
> +
> + /* port over current Polarity */
> + val = readl(driver->usb2h_strap_reg);
> + val |= OHCI_OVRCUR_POL;
> + writel(val, driver->usb2h_strap_reg);
> +
> + driver->host_mode = 1;
> + }
> +
> + data->poweron = 1;
> +exit:
> + spin_unlock_irqrestore(&driver->lock, flags);
> + return 0;
> +
> +err_shutdown:
> + data->poweron = 1;
> + spin_unlock_irqrestore(&driver->lock, flags);
> + ns2_drd_phy_shutdown(phy);
> + return ret;
> +}
> +
> +static void connect_work(struct work_struct *work)
> +{
> + struct ns2_phy_driver *driver;
> + struct ns2_phy_data *data;
> + u32 extcon_event;
> +
> + driver = container_of(to_delayed_work(work),
> + struct ns2_phy_driver, conn_work);
> + data = driver->data;
> + extcon_event = data->new_state;
> +
> + if (extcon_event == EVT_DEVICE || extcon_event == EVT_HOST) {
> + ns2_drd_phy_init(data->phy);
> + ns2_drd_phy_poweron(data->phy);
> + } else if (extcon_event == EVT_IDLE) {
> + ns2_drd_phy_shutdown(data->phy);
> + }
> +}
> +
> +static int drd_device_notify(struct notifier_block *self,
> + unsigned long event, void *ptr)
> +{
> + struct ns2_phy_driver *driver = container_of(self,
> + struct ns2_phy_driver, dev_nb);
> +
> + if (event) {
> + pr_debug("Device connected\n");
> + driver->data->new_state = EVT_DEVICE;
> + schedule_delayed_work(&driver->conn_work, 0);
> + } else {
> + pr_debug("Device disconnected\n");
> + driver->data->new_state = EVT_IDLE;
> + schedule_delayed_work(&driver->conn_work, PHY_WQ_DELAY);
> + }
> +
> + return NOTIFY_DONE;
> +}
> +
> +static int drd_host_notify(struct notifier_block *self,
> + unsigned long event, void *ptr)
> +{
> + struct ns2_phy_driver *driver = container_of(self,
> + struct ns2_phy_driver, host_nb);
> +
> + if (event) {
> + pr_debug("Host connected\n");
> + driver->data->new_state = EVT_HOST;
> + schedule_delayed_work(&driver->conn_work, 0);
> + } else {
> + pr_debug("Host disconnected\n");
> + driver->data->new_state = EVT_IDLE;
> + schedule_delayed_work(&driver->conn_work, PHY_WQ_DELAY);
> + }
> +
> + return NOTIFY_DONE;
> +}
> +
> +static void extcon_work(struct work_struct *work)
> +{
> + struct ns2_phy_driver *driver;
> + int vbus;
> + int id;
> +
> + driver = container_of(to_delayed_work(work),
> + struct ns2_phy_driver, wq_extcon);
> +
> + id = gpiod_get_value_cansleep(driver->id_gpiod);
> + vbus = gpiod_get_value_cansleep(driver->vbus_gpiod);
> +
> + if (!id && vbus) {
> + extcon_set_cable_state_(driver->edev, EXTCON_USB_HOST, true);
> + } else if (id && !vbus) {
> + extcon_set_cable_state_(driver->edev, EXTCON_USB_HOST, false);
> + extcon_set_cable_state_(driver->edev, EXTCON_USB, false);
> + } else if (id && vbus) {
> + extcon_set_cable_state_(driver->edev, EXTCON_USB, true);
> + }
> +}
> +
> +static irqreturn_t gpio_irq_handler(int irq, void *dev_id)
> +{
> + struct ns2_phy_driver *driver = dev_id;
> +
> + queue_delayed_work(system_power_efficient_wq, &driver->wq_extcon,
> + driver->debounce_jiffies);
> +
> + return IRQ_HANDLED;
> +}
> +
> +static int register_extcon_notifier(struct ns2_phy_driver *phy_driver,
> + struct device *dev)
> +{
> + struct extcon_dev *edev;
> + int ret;
> +
> + phy_driver->host_nb.notifier_call = drd_host_notify;
> + phy_driver->dev_nb.notifier_call = drd_device_notify;
> +
> + edev = phy_driver->edev;
> +
> + /* Register for device change notification */
> + ret = extcon_register_notifier(edev, EXTCON_USB,
> + &phy_driver->dev_nb);
> + if (ret < 0) {
> + dev_err(dev, "can't register extcon_dev for %s\n", edev->name);
> + return ret;
> + }
> +
> + /* Register for host change notification */
> + ret = extcon_register_notifier(edev, EXTCON_USB_HOST,
> + &phy_driver->host_nb);
> + if (ret < 0) {
> + dev_err(dev, "can't register extcon_dev for %s\n", edev->name);
> + goto err_dev;
> + }
> +
> + /* Check the device cable connect state */
> + ret = extcon_get_cable_state_(edev, EXTCON_USB);
> + if (ret < 0) {
> + dev_err(dev, "can't get extcon_dev state for %s\n", edev->name);
> + goto err_host;
> + } else if (ret) {
> + phy_driver->data->new_state = EVT_DEVICE;
> + }
> +
> + /* Check the host cable connect state */
> + ret = extcon_get_cable_state_(edev, EXTCON_USB_HOST);
> + if (ret < 0) {
> + dev_err(dev, "can't get extcon_dev state for %s\n", edev->name);
> + goto err_host;
> + } else if (ret) {
> + phy_driver->data->new_state = EVT_HOST;
> + }
> +
> + return 0;
> +
> +err_host:
> + ret = extcon_unregister_notifier(edev, EXTCON_USB_HOST,
> + &phy_driver->host_nb);
> +err_dev:
> + ret = extcon_unregister_notifier(edev, EXTCON_USB,
> + &phy_driver->dev_nb);
> + return ret;
> +}
> +
> +static struct phy_ops ops = {
> + .init = ns2_drd_phy_init,
Is this really being used by any controller driver? Can you point me to the
controller driver that is using this driver?
> + .power_on = ns2_drd_phy_poweron,
> + .power_off = ns2_drd_phy_shutdown,
missing .owner.
Thanks
Kishon
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH 2/3] Broadcom USB DRD Phy driver for Northstar2
@ 2017-01-16 10:51 ` Raviteja Garimella
0 siblings, 0 replies; 20+ messages in thread
From: Raviteja Garimella @ 2017-01-16 10:51 UTC (permalink / raw)
To: Kishon Vijay Abraham I
Cc: Rob Herring, Mark Rutland, Ray Jui, Scott Branden, Jon Mason,
Catalin Marinas, Will Deacon, devicetree, linux-kernel,
BCM Kernel Feedback, linux-arm-kernel
Hi Kishon,
On Mon, Jan 16, 2017 at 2:52 PM, Kishon Vijay Abraham I <kishon@ti.com> wrote:
> Hi,
>
> On Wednesday 30 November 2016 11:25 AM, Raviteja Garimella wrote:
>> This is driver for USB DRD Phy used in Broadcom's Northstar2
>> SoC. The phy can be configured to be in Device mode or Host
>> mode based on the type of cable connected to the port. The
>> driver registers to extcon framework to get appropriate
>> connect events for Host/Device cables connect/disconnect
>> states based on VBUS and ID interrupts.
>>
>> Signed-off-by: Raviteja Garimella <raviteja.garimella@broadcom.com>
>> ---
>> drivers/phy/Kconfig | 13 +
>> drivers/phy/Makefile | 1 +
>> drivers/phy/phy-bcm-ns2-usbdrd.c | 587 +++++++++++++++++++++++++++++++++++++++
>> 3 files changed, 601 insertions(+)
>> create mode 100644 drivers/phy/phy-bcm-ns2-usbdrd.c
>>
>> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
>> index fe00f91..b3b6a73 100644
>> --- a/drivers/phy/Kconfig
>> +++ b/drivers/phy/Kconfig
>> @@ -479,6 +479,19 @@ config PHY_CYGNUS_PCIE
>> Enable this to support the Broadcom Cygnus PCIe PHY.
>> If unsure, say N.
>>
>> +config PHY_NS2_USB_DRD
>> + tristate "Broadcom Northstar2 USB DRD PHY support"
>> + depends on OF && (ARCH_BCM_IPROC || COMPILE_TEST)
>> + select GENERIC_PHY
>> + select EXTCON
>> + default ARCH_BCM_IPROC
>> + help
>> + Enable this to support the Broadcom Northstar2 USB DRD PHY.
>> + This driver initializes the PHY in either HOST or DEVICE mode.
>> + The host or device configuration is read from device tree.
>> +
>> + If unsure, say N.
>> +
>> source "drivers/phy/tegra/Kconfig"
>>
>> config PHY_NS2_PCIE
>> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
>> index a534cf5..b733ba2 100644
>> --- a/drivers/phy/Makefile
>> +++ b/drivers/phy/Makefile
>> @@ -58,5 +58,6 @@ obj-$(CONFIG_PHY_TUSB1210) += phy-tusb1210.o
>> obj-$(CONFIG_PHY_BRCM_SATA) += phy-brcm-sata.o
>> obj-$(CONFIG_PHY_PISTACHIO_USB) += phy-pistachio-usb.o
>> obj-$(CONFIG_PHY_CYGNUS_PCIE) += phy-bcm-cygnus-pcie.o
>> +obj-$(CONFIG_PHY_NS2_USB_DRD) += phy-bcm-ns2-usbdrd.o
>> obj-$(CONFIG_ARCH_TEGRA) += tegra/
>> obj-$(CONFIG_PHY_NS2_PCIE) += phy-bcm-ns2-pcie.o
>> diff --git a/drivers/phy/phy-bcm-ns2-usbdrd.c b/drivers/phy/phy-bcm-ns2-usbdrd.c
>> new file mode 100644
>> index 0000000..460040d
>> --- /dev/null
>> +++ b/drivers/phy/phy-bcm-ns2-usbdrd.c
>> @@ -0,0 +1,587 @@
>> +/*
>> + * Copyright (C) 2016 Broadcom
>> + *
>> + * This program is free software; you can redistribute it and/or
>> + * modify it under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation version 2.
>> + *
>> + * This program is distributed "as is" WITHOUT ANY WARRANTY of any
>> + * kind, whether express or implied; without even the implied warranty
>> + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + */
>> +
>> +#include <linux/delay.h>
>> +#include <linux/extcon.h>
>> +#include <linux/gpio.h>
>> +#include <linux/gpio/consumer.h>
>> +#include <linux/init.h>
>> +#include <linux/interrupt.h>
>> +#include <linux/io.h>
>> +#include <linux/irq.h>
>> +#include <linux/mfd/syscon.h>
>> +#include <linux/module.h>
>> +#include <linux/of.h>
>> +#include <linux/of_address.h>
>> +#include <linux/phy/phy.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/regmap.h>
>> +#include <linux/slab.h>
>> +#include <linux/workqueue.h>
>> +
>> +#define ICFG_DRD_AFE 0x0
>> +#define ICFG_MISC_STAT 0x18
>> +#define ICFG_DRD_P0CTL 0x1C
>> +#define ICFG_STRAP_CTRL 0x20
>> +#define ICFG_FSM_CTRL 0x24
>> +
>> +#define IDM_RST_BIT BIT(0)
>> +#define AFE_CORERDY_VDDC BIT(18)
>> +#define PHY_PLL_RESETB BIT(15)
>> +#define PHY_RESETB BIT(14)
>> +#define PHY_PLL_LOCK BIT(0)
>> +
>> +#define DRD_DEV_MODE BIT(20)
>> +#define OHCI_OVRCUR_POL BIT(11)
>> +#define ICFG_OFF_MODE BIT(6)
>> +#define PLL_LOCK_RETRY 1000
>> +
>> +#define EVT_DEVICE 0
>> +#define EVT_HOST 1
>> +#define EVT_IDLE 2
>> +
>> +#define DRD_HOST_MODE (BIT(2) | BIT(3))
>> +#define DRD_DEVICE_MODE (BIT(4) | BIT(5))
>> +#define DRD_HOST_VAL 0x803
>> +#define DRD_DEV_VAL 0x807
>> +#define GPIO_DELAY 20
>> +#define PHY_WQ_DELAY msecs_to_jiffies(600)
>> +
>> +struct ns2_phy_data;
>> +struct ns2_phy_driver {
>> + void __iomem *icfgdrd_regs;
>> + void __iomem *idmdrd_rst_ctrl;
>> + void __iomem *crmu_usb2_ctrl;
>> + void __iomem *usb2h_strap_reg;
>> + spinlock_t lock; /* spin lock for phy driver */
>> + bool host_mode;
>> + struct ns2_phy_data *data;
>> + struct extcon_specific_cable_nb extcon_dev;
>> + struct extcon_specific_cable_nb extcon_host;
>> + struct notifier_block host_nb;
>> + struct notifier_block dev_nb;
>> + struct delayed_work conn_work;
>> + struct extcon_dev *edev;
>> + struct gpio_desc *vbus_gpiod;
>> + struct gpio_desc *id_gpiod;
>> + int id_irq;
>> + int vbus_irq;
>> + unsigned long debounce_jiffies;
>> + struct delayed_work wq_extcon;
>> +};
>> +
>> +struct ns2_phy_data {
>> + struct ns2_phy_driver *driver;
>> + struct phy *phy;
>> + int new_state;
>> + bool poweron;
>> +};
>> +
>> +static const unsigned int usb_extcon_cable[] = {
>> + EXTCON_USB,
>> + EXTCON_USB_HOST,
>> + EXTCON_NONE,
>> +};
>> +
>> +static inline int pll_lock_stat(u32 usb_reg, int reg_mask,
>> + struct ns2_phy_driver *driver)
>> +{
>> + int retry = PLL_LOCK_RETRY;
>> + u32 val;
>> +
>> + do {
>> + udelay(1);
>> + val = readl(driver->icfgdrd_regs + usb_reg);
>> + if (val & reg_mask)
>> + return 0;
>> + } while (--retry > 0);
>> +
>> + return -EBUSY;
>> +}
>> +
>> +static int ns2_drd_phy_init(struct phy *phy)
>> +{
>> + struct ns2_phy_data *data = phy_get_drvdata(phy);
>> + struct ns2_phy_driver *driver = data->driver;
>> + unsigned long flags;
>> + u32 val;
>> +
>> + spin_lock_irqsave(&driver->lock, flags);
>> +
>> + val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
>> +
>> + if (data->new_state == EVT_HOST) {
>> + val &= ~DRD_DEVICE_MODE;
>> + val |= DRD_HOST_MODE;
>> + } else {
>> + val &= ~DRD_HOST_MODE;
>> + val |= DRD_DEVICE_MODE;
>> + }
>> + writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
>> +
>> + spin_unlock_irqrestore(&driver->lock, flags);
>> + return 0;
>> +}
>> +
>> +static int ns2_drd_phy_shutdown(struct phy *phy)
>> +{
>> + struct ns2_phy_data *data = phy_get_drvdata(phy);
>> + struct ns2_phy_driver *driver = data->driver;
>> + unsigned long flags;
>> + u32 val;
>> +
>> + spin_lock_irqsave(&driver->lock, flags);
>> + if (!data->poweron)
>> + goto exit;
>> +
>> + val = readl(driver->crmu_usb2_ctrl);
>> + val &= ~AFE_CORERDY_VDDC;
>> + writel(val, driver->crmu_usb2_ctrl);
>> +
>> + driver->host_mode = 0;
>> + val = readl(driver->crmu_usb2_ctrl);
>> + val &= ~DRD_DEV_MODE;
>> + writel(val, driver->crmu_usb2_ctrl);
>> +
>> + /* Disable Host and Device Mode */
>> + val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
>> + val &= ~(DRD_HOST_MODE | DRD_DEVICE_MODE | ICFG_OFF_MODE);
>> + writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
>> +
>> + data->poweron = 0;
>> +exit:
>> + spin_unlock_irqrestore(&driver->lock, flags);
>> + return 0;
>> +}
>> +
>> +static int ns2_drd_phy_poweron(struct phy *phy)
>> +{
>> + struct ns2_phy_data *data = phy_get_drvdata(phy);
>> + struct ns2_phy_driver *driver = data->driver;
>> + u32 extcon_event = data->new_state;
>> + unsigned long flags;
>> + int ret;
>> + u32 val;
>> +
>> + spin_lock_irqsave(&driver->lock, flags);
>> + if (extcon_event == EVT_DEVICE) {
>> + if (data->poweron)
>> + goto exit;
>> +
>> + writel(DRD_DEV_VAL, driver->icfgdrd_regs + ICFG_DRD_P0CTL);
>> +
>> + val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
>> + val &= ~(DRD_HOST_MODE | ICFG_OFF_MODE);
>> + val |= DRD_DEVICE_MODE;
>> + writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
>> +
>> + val = readl(driver->idmdrd_rst_ctrl);
>> + val &= ~IDM_RST_BIT;
>> + writel(val, driver->idmdrd_rst_ctrl);
>> +
>> + val = readl(driver->crmu_usb2_ctrl);
>> + val |= (AFE_CORERDY_VDDC | DRD_DEV_MODE);
>> + writel(val, driver->crmu_usb2_ctrl);
>> +
>> + /* Bring PHY and PHY_PLL out of Reset */
>> + val = readl(driver->crmu_usb2_ctrl);
>> + val |= (PHY_PLL_RESETB | PHY_RESETB);
>> + writel(val, driver->crmu_usb2_ctrl);
>> +
>> + ret = pll_lock_stat(ICFG_MISC_STAT, PHY_PLL_LOCK, driver);
>> + if (ret < 0) {
>> + dev_err(&phy->dev, "Phy PLL lock failed\n");
>> + goto err_shutdown;
>> + }
>> + } else {
>> + if (data->poweron && driver->host_mode)
>> + goto exit;
>> +
>> + writel(DRD_HOST_VAL, driver->icfgdrd_regs + ICFG_DRD_P0CTL);
>> +
>> + val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
>> + val &= ~(DRD_DEVICE_MODE | ICFG_OFF_MODE);
>> + val |= DRD_HOST_MODE;
>> + writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
>> +
>> + val = readl(driver->crmu_usb2_ctrl);
>> + val |= AFE_CORERDY_VDDC;
>> + writel(val, driver->crmu_usb2_ctrl);
>> +
>> + ret = pll_lock_stat(ICFG_MISC_STAT, PHY_PLL_LOCK, driver);
>> + if (ret < 0) {
>> + dev_err(&phy->dev, "Phy PLL lock failed\n");
>> + goto err_shutdown;
>> + }
>> +
>> + val = readl(driver->idmdrd_rst_ctrl);
>> + val &= ~IDM_RST_BIT;
>> + writel(val, driver->idmdrd_rst_ctrl);
>> +
>> + /* port over current Polarity */
>> + val = readl(driver->usb2h_strap_reg);
>> + val |= OHCI_OVRCUR_POL;
>> + writel(val, driver->usb2h_strap_reg);
>> +
>> + driver->host_mode = 1;
>> + }
>> +
>> + data->poweron = 1;
>> +exit:
>> + spin_unlock_irqrestore(&driver->lock, flags);
>> + return 0;
>> +
>> +err_shutdown:
>> + data->poweron = 1;
>> + spin_unlock_irqrestore(&driver->lock, flags);
>> + ns2_drd_phy_shutdown(phy);
>> + return ret;
>> +}
>> +
>> +static void connect_work(struct work_struct *work)
>> +{
>> + struct ns2_phy_driver *driver;
>> + struct ns2_phy_data *data;
>> + u32 extcon_event;
>> +
>> + driver = container_of(to_delayed_work(work),
>> + struct ns2_phy_driver, conn_work);
>> + data = driver->data;
>> + extcon_event = data->new_state;
>> +
>> + if (extcon_event == EVT_DEVICE || extcon_event == EVT_HOST) {
>> + ns2_drd_phy_init(data->phy);
>> + ns2_drd_phy_poweron(data->phy);
>> + } else if (extcon_event == EVT_IDLE) {
>> + ns2_drd_phy_shutdown(data->phy);
>> + }
>> +}
>> +
>> +static int drd_device_notify(struct notifier_block *self,
>> + unsigned long event, void *ptr)
>> +{
>> + struct ns2_phy_driver *driver = container_of(self,
>> + struct ns2_phy_driver, dev_nb);
>> +
>> + if (event) {
>> + pr_debug("Device connected\n");
>> + driver->data->new_state = EVT_DEVICE;
>> + schedule_delayed_work(&driver->conn_work, 0);
>> + } else {
>> + pr_debug("Device disconnected\n");
>> + driver->data->new_state = EVT_IDLE;
>> + schedule_delayed_work(&driver->conn_work, PHY_WQ_DELAY);
>> + }
>> +
>> + return NOTIFY_DONE;
>> +}
>> +
>> +static int drd_host_notify(struct notifier_block *self,
>> + unsigned long event, void *ptr)
>> +{
>> + struct ns2_phy_driver *driver = container_of(self,
>> + struct ns2_phy_driver, host_nb);
>> +
>> + if (event) {
>> + pr_debug("Host connected\n");
>> + driver->data->new_state = EVT_HOST;
>> + schedule_delayed_work(&driver->conn_work, 0);
>> + } else {
>> + pr_debug("Host disconnected\n");
>> + driver->data->new_state = EVT_IDLE;
>> + schedule_delayed_work(&driver->conn_work, PHY_WQ_DELAY);
>> + }
>> +
>> + return NOTIFY_DONE;
>> +}
>> +
>> +static void extcon_work(struct work_struct *work)
>> +{
>> + struct ns2_phy_driver *driver;
>> + int vbus;
>> + int id;
>> +
>> + driver = container_of(to_delayed_work(work),
>> + struct ns2_phy_driver, wq_extcon);
>> +
>> + id = gpiod_get_value_cansleep(driver->id_gpiod);
>> + vbus = gpiod_get_value_cansleep(driver->vbus_gpiod);
>> +
>> + if (!id && vbus) {
>> + extcon_set_cable_state_(driver->edev, EXTCON_USB_HOST, true);
>> + } else if (id && !vbus) {
>> + extcon_set_cable_state_(driver->edev, EXTCON_USB_HOST, false);
>> + extcon_set_cable_state_(driver->edev, EXTCON_USB, false);
>> + } else if (id && vbus) {
>> + extcon_set_cable_state_(driver->edev, EXTCON_USB, true);
>> + }
>> +}
>> +
>> +static irqreturn_t gpio_irq_handler(int irq, void *dev_id)
>> +{
>> + struct ns2_phy_driver *driver = dev_id;
>> +
>> + queue_delayed_work(system_power_efficient_wq, &driver->wq_extcon,
>> + driver->debounce_jiffies);
>> +
>> + return IRQ_HANDLED;
>> +}
>> +
>> +static int register_extcon_notifier(struct ns2_phy_driver *phy_driver,
>> + struct device *dev)
>> +{
>> + struct extcon_dev *edev;
>> + int ret;
>> +
>> + phy_driver->host_nb.notifier_call = drd_host_notify;
>> + phy_driver->dev_nb.notifier_call = drd_device_notify;
>> +
>> + edev = phy_driver->edev;
>> +
>> + /* Register for device change notification */
>> + ret = extcon_register_notifier(edev, EXTCON_USB,
>> + &phy_driver->dev_nb);
>> + if (ret < 0) {
>> + dev_err(dev, "can't register extcon_dev for %s\n", edev->name);
>> + return ret;
>> + }
>> +
>> + /* Register for host change notification */
>> + ret = extcon_register_notifier(edev, EXTCON_USB_HOST,
>> + &phy_driver->host_nb);
>> + if (ret < 0) {
>> + dev_err(dev, "can't register extcon_dev for %s\n", edev->name);
>> + goto err_dev;
>> + }
>> +
>> + /* Check the device cable connect state */
>> + ret = extcon_get_cable_state_(edev, EXTCON_USB);
>> + if (ret < 0) {
>> + dev_err(dev, "can't get extcon_dev state for %s\n", edev->name);
>> + goto err_host;
>> + } else if (ret) {
>> + phy_driver->data->new_state = EVT_DEVICE;
>> + }
>> +
>> + /* Check the host cable connect state */
>> + ret = extcon_get_cable_state_(edev, EXTCON_USB_HOST);
>> + if (ret < 0) {
>> + dev_err(dev, "can't get extcon_dev state for %s\n", edev->name);
>> + goto err_host;
>> + } else if (ret) {
>> + phy_driver->data->new_state = EVT_HOST;
>> + }
>> +
>> + return 0;
>> +
>> +err_host:
>> + ret = extcon_unregister_notifier(edev, EXTCON_USB_HOST,
>> + &phy_driver->host_nb);
>> +err_dev:
>> + ret = extcon_unregister_notifier(edev, EXTCON_USB,
>> + &phy_driver->dev_nb);
>> + return ret;
>> +}
>> +
>> +static struct phy_ops ops = {
>> + .init = ns2_drd_phy_init,
>
> Is this really being used by any controller driver? Can you point me to the
> controller driver that is using this driver?
This will be used by Synopsys UDC that's integrated into Broadcom's Northstar2
and Cygnus SoC's. I am currently working on upstream review comments for the
same in a different patch series. The "amd5536udc" driver is being modified for
platform device support (as per the suggestions I received in reviews).
>
>> + .power_on = ns2_drd_phy_poweron,
>> + .power_off = ns2_drd_phy_shutdown,
>
> missing .owner.
Will fix this.
Thanks,
Ravi
>
> Thanks
> Kishon
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH 2/3] Broadcom USB DRD Phy driver for Northstar2
@ 2017-01-16 10:51 ` Raviteja Garimella
0 siblings, 0 replies; 20+ messages in thread
From: Raviteja Garimella @ 2017-01-16 10:51 UTC (permalink / raw)
To: Kishon Vijay Abraham I
Cc: Rob Herring, Mark Rutland, Ray Jui, Scott Branden, Jon Mason,
Catalin Marinas, Will Deacon, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA, BCM Kernel Feedback,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
Hi Kishon,
On Mon, Jan 16, 2017 at 2:52 PM, Kishon Vijay Abraham I <kishon-l0cyMroinI0@public.gmane.org> wrote:
> Hi,
>
> On Wednesday 30 November 2016 11:25 AM, Raviteja Garimella wrote:
>> This is driver for USB DRD Phy used in Broadcom's Northstar2
>> SoC. The phy can be configured to be in Device mode or Host
>> mode based on the type of cable connected to the port. The
>> driver registers to extcon framework to get appropriate
>> connect events for Host/Device cables connect/disconnect
>> states based on VBUS and ID interrupts.
>>
>> Signed-off-by: Raviteja Garimella <raviteja.garimella-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>
>> ---
>> drivers/phy/Kconfig | 13 +
>> drivers/phy/Makefile | 1 +
>> drivers/phy/phy-bcm-ns2-usbdrd.c | 587 +++++++++++++++++++++++++++++++++++++++
>> 3 files changed, 601 insertions(+)
>> create mode 100644 drivers/phy/phy-bcm-ns2-usbdrd.c
>>
>> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
>> index fe00f91..b3b6a73 100644
>> --- a/drivers/phy/Kconfig
>> +++ b/drivers/phy/Kconfig
>> @@ -479,6 +479,19 @@ config PHY_CYGNUS_PCIE
>> Enable this to support the Broadcom Cygnus PCIe PHY.
>> If unsure, say N.
>>
>> +config PHY_NS2_USB_DRD
>> + tristate "Broadcom Northstar2 USB DRD PHY support"
>> + depends on OF && (ARCH_BCM_IPROC || COMPILE_TEST)
>> + select GENERIC_PHY
>> + select EXTCON
>> + default ARCH_BCM_IPROC
>> + help
>> + Enable this to support the Broadcom Northstar2 USB DRD PHY.
>> + This driver initializes the PHY in either HOST or DEVICE mode.
>> + The host or device configuration is read from device tree.
>> +
>> + If unsure, say N.
>> +
>> source "drivers/phy/tegra/Kconfig"
>>
>> config PHY_NS2_PCIE
>> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
>> index a534cf5..b733ba2 100644
>> --- a/drivers/phy/Makefile
>> +++ b/drivers/phy/Makefile
>> @@ -58,5 +58,6 @@ obj-$(CONFIG_PHY_TUSB1210) += phy-tusb1210.o
>> obj-$(CONFIG_PHY_BRCM_SATA) += phy-brcm-sata.o
>> obj-$(CONFIG_PHY_PISTACHIO_USB) += phy-pistachio-usb.o
>> obj-$(CONFIG_PHY_CYGNUS_PCIE) += phy-bcm-cygnus-pcie.o
>> +obj-$(CONFIG_PHY_NS2_USB_DRD) += phy-bcm-ns2-usbdrd.o
>> obj-$(CONFIG_ARCH_TEGRA) += tegra/
>> obj-$(CONFIG_PHY_NS2_PCIE) += phy-bcm-ns2-pcie.o
>> diff --git a/drivers/phy/phy-bcm-ns2-usbdrd.c b/drivers/phy/phy-bcm-ns2-usbdrd.c
>> new file mode 100644
>> index 0000000..460040d
>> --- /dev/null
>> +++ b/drivers/phy/phy-bcm-ns2-usbdrd.c
>> @@ -0,0 +1,587 @@
>> +/*
>> + * Copyright (C) 2016 Broadcom
>> + *
>> + * This program is free software; you can redistribute it and/or
>> + * modify it under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation version 2.
>> + *
>> + * This program is distributed "as is" WITHOUT ANY WARRANTY of any
>> + * kind, whether express or implied; without even the implied warranty
>> + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + */
>> +
>> +#include <linux/delay.h>
>> +#include <linux/extcon.h>
>> +#include <linux/gpio.h>
>> +#include <linux/gpio/consumer.h>
>> +#include <linux/init.h>
>> +#include <linux/interrupt.h>
>> +#include <linux/io.h>
>> +#include <linux/irq.h>
>> +#include <linux/mfd/syscon.h>
>> +#include <linux/module.h>
>> +#include <linux/of.h>
>> +#include <linux/of_address.h>
>> +#include <linux/phy/phy.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/regmap.h>
>> +#include <linux/slab.h>
>> +#include <linux/workqueue.h>
>> +
>> +#define ICFG_DRD_AFE 0x0
>> +#define ICFG_MISC_STAT 0x18
>> +#define ICFG_DRD_P0CTL 0x1C
>> +#define ICFG_STRAP_CTRL 0x20
>> +#define ICFG_FSM_CTRL 0x24
>> +
>> +#define IDM_RST_BIT BIT(0)
>> +#define AFE_CORERDY_VDDC BIT(18)
>> +#define PHY_PLL_RESETB BIT(15)
>> +#define PHY_RESETB BIT(14)
>> +#define PHY_PLL_LOCK BIT(0)
>> +
>> +#define DRD_DEV_MODE BIT(20)
>> +#define OHCI_OVRCUR_POL BIT(11)
>> +#define ICFG_OFF_MODE BIT(6)
>> +#define PLL_LOCK_RETRY 1000
>> +
>> +#define EVT_DEVICE 0
>> +#define EVT_HOST 1
>> +#define EVT_IDLE 2
>> +
>> +#define DRD_HOST_MODE (BIT(2) | BIT(3))
>> +#define DRD_DEVICE_MODE (BIT(4) | BIT(5))
>> +#define DRD_HOST_VAL 0x803
>> +#define DRD_DEV_VAL 0x807
>> +#define GPIO_DELAY 20
>> +#define PHY_WQ_DELAY msecs_to_jiffies(600)
>> +
>> +struct ns2_phy_data;
>> +struct ns2_phy_driver {
>> + void __iomem *icfgdrd_regs;
>> + void __iomem *idmdrd_rst_ctrl;
>> + void __iomem *crmu_usb2_ctrl;
>> + void __iomem *usb2h_strap_reg;
>> + spinlock_t lock; /* spin lock for phy driver */
>> + bool host_mode;
>> + struct ns2_phy_data *data;
>> + struct extcon_specific_cable_nb extcon_dev;
>> + struct extcon_specific_cable_nb extcon_host;
>> + struct notifier_block host_nb;
>> + struct notifier_block dev_nb;
>> + struct delayed_work conn_work;
>> + struct extcon_dev *edev;
>> + struct gpio_desc *vbus_gpiod;
>> + struct gpio_desc *id_gpiod;
>> + int id_irq;
>> + int vbus_irq;
>> + unsigned long debounce_jiffies;
>> + struct delayed_work wq_extcon;
>> +};
>> +
>> +struct ns2_phy_data {
>> + struct ns2_phy_driver *driver;
>> + struct phy *phy;
>> + int new_state;
>> + bool poweron;
>> +};
>> +
>> +static const unsigned int usb_extcon_cable[] = {
>> + EXTCON_USB,
>> + EXTCON_USB_HOST,
>> + EXTCON_NONE,
>> +};
>> +
>> +static inline int pll_lock_stat(u32 usb_reg, int reg_mask,
>> + struct ns2_phy_driver *driver)
>> +{
>> + int retry = PLL_LOCK_RETRY;
>> + u32 val;
>> +
>> + do {
>> + udelay(1);
>> + val = readl(driver->icfgdrd_regs + usb_reg);
>> + if (val & reg_mask)
>> + return 0;
>> + } while (--retry > 0);
>> +
>> + return -EBUSY;
>> +}
>> +
>> +static int ns2_drd_phy_init(struct phy *phy)
>> +{
>> + struct ns2_phy_data *data = phy_get_drvdata(phy);
>> + struct ns2_phy_driver *driver = data->driver;
>> + unsigned long flags;
>> + u32 val;
>> +
>> + spin_lock_irqsave(&driver->lock, flags);
>> +
>> + val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
>> +
>> + if (data->new_state == EVT_HOST) {
>> + val &= ~DRD_DEVICE_MODE;
>> + val |= DRD_HOST_MODE;
>> + } else {
>> + val &= ~DRD_HOST_MODE;
>> + val |= DRD_DEVICE_MODE;
>> + }
>> + writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
>> +
>> + spin_unlock_irqrestore(&driver->lock, flags);
>> + return 0;
>> +}
>> +
>> +static int ns2_drd_phy_shutdown(struct phy *phy)
>> +{
>> + struct ns2_phy_data *data = phy_get_drvdata(phy);
>> + struct ns2_phy_driver *driver = data->driver;
>> + unsigned long flags;
>> + u32 val;
>> +
>> + spin_lock_irqsave(&driver->lock, flags);
>> + if (!data->poweron)
>> + goto exit;
>> +
>> + val = readl(driver->crmu_usb2_ctrl);
>> + val &= ~AFE_CORERDY_VDDC;
>> + writel(val, driver->crmu_usb2_ctrl);
>> +
>> + driver->host_mode = 0;
>> + val = readl(driver->crmu_usb2_ctrl);
>> + val &= ~DRD_DEV_MODE;
>> + writel(val, driver->crmu_usb2_ctrl);
>> +
>> + /* Disable Host and Device Mode */
>> + val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
>> + val &= ~(DRD_HOST_MODE | DRD_DEVICE_MODE | ICFG_OFF_MODE);
>> + writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
>> +
>> + data->poweron = 0;
>> +exit:
>> + spin_unlock_irqrestore(&driver->lock, flags);
>> + return 0;
>> +}
>> +
>> +static int ns2_drd_phy_poweron(struct phy *phy)
>> +{
>> + struct ns2_phy_data *data = phy_get_drvdata(phy);
>> + struct ns2_phy_driver *driver = data->driver;
>> + u32 extcon_event = data->new_state;
>> + unsigned long flags;
>> + int ret;
>> + u32 val;
>> +
>> + spin_lock_irqsave(&driver->lock, flags);
>> + if (extcon_event == EVT_DEVICE) {
>> + if (data->poweron)
>> + goto exit;
>> +
>> + writel(DRD_DEV_VAL, driver->icfgdrd_regs + ICFG_DRD_P0CTL);
>> +
>> + val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
>> + val &= ~(DRD_HOST_MODE | ICFG_OFF_MODE);
>> + val |= DRD_DEVICE_MODE;
>> + writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
>> +
>> + val = readl(driver->idmdrd_rst_ctrl);
>> + val &= ~IDM_RST_BIT;
>> + writel(val, driver->idmdrd_rst_ctrl);
>> +
>> + val = readl(driver->crmu_usb2_ctrl);
>> + val |= (AFE_CORERDY_VDDC | DRD_DEV_MODE);
>> + writel(val, driver->crmu_usb2_ctrl);
>> +
>> + /* Bring PHY and PHY_PLL out of Reset */
>> + val = readl(driver->crmu_usb2_ctrl);
>> + val |= (PHY_PLL_RESETB | PHY_RESETB);
>> + writel(val, driver->crmu_usb2_ctrl);
>> +
>> + ret = pll_lock_stat(ICFG_MISC_STAT, PHY_PLL_LOCK, driver);
>> + if (ret < 0) {
>> + dev_err(&phy->dev, "Phy PLL lock failed\n");
>> + goto err_shutdown;
>> + }
>> + } else {
>> + if (data->poweron && driver->host_mode)
>> + goto exit;
>> +
>> + writel(DRD_HOST_VAL, driver->icfgdrd_regs + ICFG_DRD_P0CTL);
>> +
>> + val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
>> + val &= ~(DRD_DEVICE_MODE | ICFG_OFF_MODE);
>> + val |= DRD_HOST_MODE;
>> + writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
>> +
>> + val = readl(driver->crmu_usb2_ctrl);
>> + val |= AFE_CORERDY_VDDC;
>> + writel(val, driver->crmu_usb2_ctrl);
>> +
>> + ret = pll_lock_stat(ICFG_MISC_STAT, PHY_PLL_LOCK, driver);
>> + if (ret < 0) {
>> + dev_err(&phy->dev, "Phy PLL lock failed\n");
>> + goto err_shutdown;
>> + }
>> +
>> + val = readl(driver->idmdrd_rst_ctrl);
>> + val &= ~IDM_RST_BIT;
>> + writel(val, driver->idmdrd_rst_ctrl);
>> +
>> + /* port over current Polarity */
>> + val = readl(driver->usb2h_strap_reg);
>> + val |= OHCI_OVRCUR_POL;
>> + writel(val, driver->usb2h_strap_reg);
>> +
>> + driver->host_mode = 1;
>> + }
>> +
>> + data->poweron = 1;
>> +exit:
>> + spin_unlock_irqrestore(&driver->lock, flags);
>> + return 0;
>> +
>> +err_shutdown:
>> + data->poweron = 1;
>> + spin_unlock_irqrestore(&driver->lock, flags);
>> + ns2_drd_phy_shutdown(phy);
>> + return ret;
>> +}
>> +
>> +static void connect_work(struct work_struct *work)
>> +{
>> + struct ns2_phy_driver *driver;
>> + struct ns2_phy_data *data;
>> + u32 extcon_event;
>> +
>> + driver = container_of(to_delayed_work(work),
>> + struct ns2_phy_driver, conn_work);
>> + data = driver->data;
>> + extcon_event = data->new_state;
>> +
>> + if (extcon_event == EVT_DEVICE || extcon_event == EVT_HOST) {
>> + ns2_drd_phy_init(data->phy);
>> + ns2_drd_phy_poweron(data->phy);
>> + } else if (extcon_event == EVT_IDLE) {
>> + ns2_drd_phy_shutdown(data->phy);
>> + }
>> +}
>> +
>> +static int drd_device_notify(struct notifier_block *self,
>> + unsigned long event, void *ptr)
>> +{
>> + struct ns2_phy_driver *driver = container_of(self,
>> + struct ns2_phy_driver, dev_nb);
>> +
>> + if (event) {
>> + pr_debug("Device connected\n");
>> + driver->data->new_state = EVT_DEVICE;
>> + schedule_delayed_work(&driver->conn_work, 0);
>> + } else {
>> + pr_debug("Device disconnected\n");
>> + driver->data->new_state = EVT_IDLE;
>> + schedule_delayed_work(&driver->conn_work, PHY_WQ_DELAY);
>> + }
>> +
>> + return NOTIFY_DONE;
>> +}
>> +
>> +static int drd_host_notify(struct notifier_block *self,
>> + unsigned long event, void *ptr)
>> +{
>> + struct ns2_phy_driver *driver = container_of(self,
>> + struct ns2_phy_driver, host_nb);
>> +
>> + if (event) {
>> + pr_debug("Host connected\n");
>> + driver->data->new_state = EVT_HOST;
>> + schedule_delayed_work(&driver->conn_work, 0);
>> + } else {
>> + pr_debug("Host disconnected\n");
>> + driver->data->new_state = EVT_IDLE;
>> + schedule_delayed_work(&driver->conn_work, PHY_WQ_DELAY);
>> + }
>> +
>> + return NOTIFY_DONE;
>> +}
>> +
>> +static void extcon_work(struct work_struct *work)
>> +{
>> + struct ns2_phy_driver *driver;
>> + int vbus;
>> + int id;
>> +
>> + driver = container_of(to_delayed_work(work),
>> + struct ns2_phy_driver, wq_extcon);
>> +
>> + id = gpiod_get_value_cansleep(driver->id_gpiod);
>> + vbus = gpiod_get_value_cansleep(driver->vbus_gpiod);
>> +
>> + if (!id && vbus) {
>> + extcon_set_cable_state_(driver->edev, EXTCON_USB_HOST, true);
>> + } else if (id && !vbus) {
>> + extcon_set_cable_state_(driver->edev, EXTCON_USB_HOST, false);
>> + extcon_set_cable_state_(driver->edev, EXTCON_USB, false);
>> + } else if (id && vbus) {
>> + extcon_set_cable_state_(driver->edev, EXTCON_USB, true);
>> + }
>> +}
>> +
>> +static irqreturn_t gpio_irq_handler(int irq, void *dev_id)
>> +{
>> + struct ns2_phy_driver *driver = dev_id;
>> +
>> + queue_delayed_work(system_power_efficient_wq, &driver->wq_extcon,
>> + driver->debounce_jiffies);
>> +
>> + return IRQ_HANDLED;
>> +}
>> +
>> +static int register_extcon_notifier(struct ns2_phy_driver *phy_driver,
>> + struct device *dev)
>> +{
>> + struct extcon_dev *edev;
>> + int ret;
>> +
>> + phy_driver->host_nb.notifier_call = drd_host_notify;
>> + phy_driver->dev_nb.notifier_call = drd_device_notify;
>> +
>> + edev = phy_driver->edev;
>> +
>> + /* Register for device change notification */
>> + ret = extcon_register_notifier(edev, EXTCON_USB,
>> + &phy_driver->dev_nb);
>> + if (ret < 0) {
>> + dev_err(dev, "can't register extcon_dev for %s\n", edev->name);
>> + return ret;
>> + }
>> +
>> + /* Register for host change notification */
>> + ret = extcon_register_notifier(edev, EXTCON_USB_HOST,
>> + &phy_driver->host_nb);
>> + if (ret < 0) {
>> + dev_err(dev, "can't register extcon_dev for %s\n", edev->name);
>> + goto err_dev;
>> + }
>> +
>> + /* Check the device cable connect state */
>> + ret = extcon_get_cable_state_(edev, EXTCON_USB);
>> + if (ret < 0) {
>> + dev_err(dev, "can't get extcon_dev state for %s\n", edev->name);
>> + goto err_host;
>> + } else if (ret) {
>> + phy_driver->data->new_state = EVT_DEVICE;
>> + }
>> +
>> + /* Check the host cable connect state */
>> + ret = extcon_get_cable_state_(edev, EXTCON_USB_HOST);
>> + if (ret < 0) {
>> + dev_err(dev, "can't get extcon_dev state for %s\n", edev->name);
>> + goto err_host;
>> + } else if (ret) {
>> + phy_driver->data->new_state = EVT_HOST;
>> + }
>> +
>> + return 0;
>> +
>> +err_host:
>> + ret = extcon_unregister_notifier(edev, EXTCON_USB_HOST,
>> + &phy_driver->host_nb);
>> +err_dev:
>> + ret = extcon_unregister_notifier(edev, EXTCON_USB,
>> + &phy_driver->dev_nb);
>> + return ret;
>> +}
>> +
>> +static struct phy_ops ops = {
>> + .init = ns2_drd_phy_init,
>
> Is this really being used by any controller driver? Can you point me to the
> controller driver that is using this driver?
This will be used by Synopsys UDC that's integrated into Broadcom's Northstar2
and Cygnus SoC's. I am currently working on upstream review comments for the
same in a different patch series. The "amd5536udc" driver is being modified for
platform device support (as per the suggestions I received in reviews).
>
>> + .power_on = ns2_drd_phy_poweron,
>> + .power_off = ns2_drd_phy_shutdown,
>
> missing .owner.
Will fix this.
Thanks,
Ravi
>
> Thanks
> Kishon
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 20+ messages in thread
* [PATCH 2/3] Broadcom USB DRD Phy driver for Northstar2
@ 2017-01-16 10:51 ` Raviteja Garimella
0 siblings, 0 replies; 20+ messages in thread
From: Raviteja Garimella @ 2017-01-16 10:51 UTC (permalink / raw)
To: linux-arm-kernel
Hi Kishon,
On Mon, Jan 16, 2017 at 2:52 PM, Kishon Vijay Abraham I <kishon@ti.com> wrote:
> Hi,
>
> On Wednesday 30 November 2016 11:25 AM, Raviteja Garimella wrote:
>> This is driver for USB DRD Phy used in Broadcom's Northstar2
>> SoC. The phy can be configured to be in Device mode or Host
>> mode based on the type of cable connected to the port. The
>> driver registers to extcon framework to get appropriate
>> connect events for Host/Device cables connect/disconnect
>> states based on VBUS and ID interrupts.
>>
>> Signed-off-by: Raviteja Garimella <raviteja.garimella@broadcom.com>
>> ---
>> drivers/phy/Kconfig | 13 +
>> drivers/phy/Makefile | 1 +
>> drivers/phy/phy-bcm-ns2-usbdrd.c | 587 +++++++++++++++++++++++++++++++++++++++
>> 3 files changed, 601 insertions(+)
>> create mode 100644 drivers/phy/phy-bcm-ns2-usbdrd.c
>>
>> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
>> index fe00f91..b3b6a73 100644
>> --- a/drivers/phy/Kconfig
>> +++ b/drivers/phy/Kconfig
>> @@ -479,6 +479,19 @@ config PHY_CYGNUS_PCIE
>> Enable this to support the Broadcom Cygnus PCIe PHY.
>> If unsure, say N.
>>
>> +config PHY_NS2_USB_DRD
>> + tristate "Broadcom Northstar2 USB DRD PHY support"
>> + depends on OF && (ARCH_BCM_IPROC || COMPILE_TEST)
>> + select GENERIC_PHY
>> + select EXTCON
>> + default ARCH_BCM_IPROC
>> + help
>> + Enable this to support the Broadcom Northstar2 USB DRD PHY.
>> + This driver initializes the PHY in either HOST or DEVICE mode.
>> + The host or device configuration is read from device tree.
>> +
>> + If unsure, say N.
>> +
>> source "drivers/phy/tegra/Kconfig"
>>
>> config PHY_NS2_PCIE
>> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
>> index a534cf5..b733ba2 100644
>> --- a/drivers/phy/Makefile
>> +++ b/drivers/phy/Makefile
>> @@ -58,5 +58,6 @@ obj-$(CONFIG_PHY_TUSB1210) += phy-tusb1210.o
>> obj-$(CONFIG_PHY_BRCM_SATA) += phy-brcm-sata.o
>> obj-$(CONFIG_PHY_PISTACHIO_USB) += phy-pistachio-usb.o
>> obj-$(CONFIG_PHY_CYGNUS_PCIE) += phy-bcm-cygnus-pcie.o
>> +obj-$(CONFIG_PHY_NS2_USB_DRD) += phy-bcm-ns2-usbdrd.o
>> obj-$(CONFIG_ARCH_TEGRA) += tegra/
>> obj-$(CONFIG_PHY_NS2_PCIE) += phy-bcm-ns2-pcie.o
>> diff --git a/drivers/phy/phy-bcm-ns2-usbdrd.c b/drivers/phy/phy-bcm-ns2-usbdrd.c
>> new file mode 100644
>> index 0000000..460040d
>> --- /dev/null
>> +++ b/drivers/phy/phy-bcm-ns2-usbdrd.c
>> @@ -0,0 +1,587 @@
>> +/*
>> + * Copyright (C) 2016 Broadcom
>> + *
>> + * This program is free software; you can redistribute it and/or
>> + * modify it under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation version 2.
>> + *
>> + * This program is distributed "as is" WITHOUT ANY WARRANTY of any
>> + * kind, whether express or implied; without even the implied warranty
>> + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + */
>> +
>> +#include <linux/delay.h>
>> +#include <linux/extcon.h>
>> +#include <linux/gpio.h>
>> +#include <linux/gpio/consumer.h>
>> +#include <linux/init.h>
>> +#include <linux/interrupt.h>
>> +#include <linux/io.h>
>> +#include <linux/irq.h>
>> +#include <linux/mfd/syscon.h>
>> +#include <linux/module.h>
>> +#include <linux/of.h>
>> +#include <linux/of_address.h>
>> +#include <linux/phy/phy.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/regmap.h>
>> +#include <linux/slab.h>
>> +#include <linux/workqueue.h>
>> +
>> +#define ICFG_DRD_AFE 0x0
>> +#define ICFG_MISC_STAT 0x18
>> +#define ICFG_DRD_P0CTL 0x1C
>> +#define ICFG_STRAP_CTRL 0x20
>> +#define ICFG_FSM_CTRL 0x24
>> +
>> +#define IDM_RST_BIT BIT(0)
>> +#define AFE_CORERDY_VDDC BIT(18)
>> +#define PHY_PLL_RESETB BIT(15)
>> +#define PHY_RESETB BIT(14)
>> +#define PHY_PLL_LOCK BIT(0)
>> +
>> +#define DRD_DEV_MODE BIT(20)
>> +#define OHCI_OVRCUR_POL BIT(11)
>> +#define ICFG_OFF_MODE BIT(6)
>> +#define PLL_LOCK_RETRY 1000
>> +
>> +#define EVT_DEVICE 0
>> +#define EVT_HOST 1
>> +#define EVT_IDLE 2
>> +
>> +#define DRD_HOST_MODE (BIT(2) | BIT(3))
>> +#define DRD_DEVICE_MODE (BIT(4) | BIT(5))
>> +#define DRD_HOST_VAL 0x803
>> +#define DRD_DEV_VAL 0x807
>> +#define GPIO_DELAY 20
>> +#define PHY_WQ_DELAY msecs_to_jiffies(600)
>> +
>> +struct ns2_phy_data;
>> +struct ns2_phy_driver {
>> + void __iomem *icfgdrd_regs;
>> + void __iomem *idmdrd_rst_ctrl;
>> + void __iomem *crmu_usb2_ctrl;
>> + void __iomem *usb2h_strap_reg;
>> + spinlock_t lock; /* spin lock for phy driver */
>> + bool host_mode;
>> + struct ns2_phy_data *data;
>> + struct extcon_specific_cable_nb extcon_dev;
>> + struct extcon_specific_cable_nb extcon_host;
>> + struct notifier_block host_nb;
>> + struct notifier_block dev_nb;
>> + struct delayed_work conn_work;
>> + struct extcon_dev *edev;
>> + struct gpio_desc *vbus_gpiod;
>> + struct gpio_desc *id_gpiod;
>> + int id_irq;
>> + int vbus_irq;
>> + unsigned long debounce_jiffies;
>> + struct delayed_work wq_extcon;
>> +};
>> +
>> +struct ns2_phy_data {
>> + struct ns2_phy_driver *driver;
>> + struct phy *phy;
>> + int new_state;
>> + bool poweron;
>> +};
>> +
>> +static const unsigned int usb_extcon_cable[] = {
>> + EXTCON_USB,
>> + EXTCON_USB_HOST,
>> + EXTCON_NONE,
>> +};
>> +
>> +static inline int pll_lock_stat(u32 usb_reg, int reg_mask,
>> + struct ns2_phy_driver *driver)
>> +{
>> + int retry = PLL_LOCK_RETRY;
>> + u32 val;
>> +
>> + do {
>> + udelay(1);
>> + val = readl(driver->icfgdrd_regs + usb_reg);
>> + if (val & reg_mask)
>> + return 0;
>> + } while (--retry > 0);
>> +
>> + return -EBUSY;
>> +}
>> +
>> +static int ns2_drd_phy_init(struct phy *phy)
>> +{
>> + struct ns2_phy_data *data = phy_get_drvdata(phy);
>> + struct ns2_phy_driver *driver = data->driver;
>> + unsigned long flags;
>> + u32 val;
>> +
>> + spin_lock_irqsave(&driver->lock, flags);
>> +
>> + val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
>> +
>> + if (data->new_state == EVT_HOST) {
>> + val &= ~DRD_DEVICE_MODE;
>> + val |= DRD_HOST_MODE;
>> + } else {
>> + val &= ~DRD_HOST_MODE;
>> + val |= DRD_DEVICE_MODE;
>> + }
>> + writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
>> +
>> + spin_unlock_irqrestore(&driver->lock, flags);
>> + return 0;
>> +}
>> +
>> +static int ns2_drd_phy_shutdown(struct phy *phy)
>> +{
>> + struct ns2_phy_data *data = phy_get_drvdata(phy);
>> + struct ns2_phy_driver *driver = data->driver;
>> + unsigned long flags;
>> + u32 val;
>> +
>> + spin_lock_irqsave(&driver->lock, flags);
>> + if (!data->poweron)
>> + goto exit;
>> +
>> + val = readl(driver->crmu_usb2_ctrl);
>> + val &= ~AFE_CORERDY_VDDC;
>> + writel(val, driver->crmu_usb2_ctrl);
>> +
>> + driver->host_mode = 0;
>> + val = readl(driver->crmu_usb2_ctrl);
>> + val &= ~DRD_DEV_MODE;
>> + writel(val, driver->crmu_usb2_ctrl);
>> +
>> + /* Disable Host and Device Mode */
>> + val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
>> + val &= ~(DRD_HOST_MODE | DRD_DEVICE_MODE | ICFG_OFF_MODE);
>> + writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
>> +
>> + data->poweron = 0;
>> +exit:
>> + spin_unlock_irqrestore(&driver->lock, flags);
>> + return 0;
>> +}
>> +
>> +static int ns2_drd_phy_poweron(struct phy *phy)
>> +{
>> + struct ns2_phy_data *data = phy_get_drvdata(phy);
>> + struct ns2_phy_driver *driver = data->driver;
>> + u32 extcon_event = data->new_state;
>> + unsigned long flags;
>> + int ret;
>> + u32 val;
>> +
>> + spin_lock_irqsave(&driver->lock, flags);
>> + if (extcon_event == EVT_DEVICE) {
>> + if (data->poweron)
>> + goto exit;
>> +
>> + writel(DRD_DEV_VAL, driver->icfgdrd_regs + ICFG_DRD_P0CTL);
>> +
>> + val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
>> + val &= ~(DRD_HOST_MODE | ICFG_OFF_MODE);
>> + val |= DRD_DEVICE_MODE;
>> + writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
>> +
>> + val = readl(driver->idmdrd_rst_ctrl);
>> + val &= ~IDM_RST_BIT;
>> + writel(val, driver->idmdrd_rst_ctrl);
>> +
>> + val = readl(driver->crmu_usb2_ctrl);
>> + val |= (AFE_CORERDY_VDDC | DRD_DEV_MODE);
>> + writel(val, driver->crmu_usb2_ctrl);
>> +
>> + /* Bring PHY and PHY_PLL out of Reset */
>> + val = readl(driver->crmu_usb2_ctrl);
>> + val |= (PHY_PLL_RESETB | PHY_RESETB);
>> + writel(val, driver->crmu_usb2_ctrl);
>> +
>> + ret = pll_lock_stat(ICFG_MISC_STAT, PHY_PLL_LOCK, driver);
>> + if (ret < 0) {
>> + dev_err(&phy->dev, "Phy PLL lock failed\n");
>> + goto err_shutdown;
>> + }
>> + } else {
>> + if (data->poweron && driver->host_mode)
>> + goto exit;
>> +
>> + writel(DRD_HOST_VAL, driver->icfgdrd_regs + ICFG_DRD_P0CTL);
>> +
>> + val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
>> + val &= ~(DRD_DEVICE_MODE | ICFG_OFF_MODE);
>> + val |= DRD_HOST_MODE;
>> + writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
>> +
>> + val = readl(driver->crmu_usb2_ctrl);
>> + val |= AFE_CORERDY_VDDC;
>> + writel(val, driver->crmu_usb2_ctrl);
>> +
>> + ret = pll_lock_stat(ICFG_MISC_STAT, PHY_PLL_LOCK, driver);
>> + if (ret < 0) {
>> + dev_err(&phy->dev, "Phy PLL lock failed\n");
>> + goto err_shutdown;
>> + }
>> +
>> + val = readl(driver->idmdrd_rst_ctrl);
>> + val &= ~IDM_RST_BIT;
>> + writel(val, driver->idmdrd_rst_ctrl);
>> +
>> + /* port over current Polarity */
>> + val = readl(driver->usb2h_strap_reg);
>> + val |= OHCI_OVRCUR_POL;
>> + writel(val, driver->usb2h_strap_reg);
>> +
>> + driver->host_mode = 1;
>> + }
>> +
>> + data->poweron = 1;
>> +exit:
>> + spin_unlock_irqrestore(&driver->lock, flags);
>> + return 0;
>> +
>> +err_shutdown:
>> + data->poweron = 1;
>> + spin_unlock_irqrestore(&driver->lock, flags);
>> + ns2_drd_phy_shutdown(phy);
>> + return ret;
>> +}
>> +
>> +static void connect_work(struct work_struct *work)
>> +{
>> + struct ns2_phy_driver *driver;
>> + struct ns2_phy_data *data;
>> + u32 extcon_event;
>> +
>> + driver = container_of(to_delayed_work(work),
>> + struct ns2_phy_driver, conn_work);
>> + data = driver->data;
>> + extcon_event = data->new_state;
>> +
>> + if (extcon_event == EVT_DEVICE || extcon_event == EVT_HOST) {
>> + ns2_drd_phy_init(data->phy);
>> + ns2_drd_phy_poweron(data->phy);
>> + } else if (extcon_event == EVT_IDLE) {
>> + ns2_drd_phy_shutdown(data->phy);
>> + }
>> +}
>> +
>> +static int drd_device_notify(struct notifier_block *self,
>> + unsigned long event, void *ptr)
>> +{
>> + struct ns2_phy_driver *driver = container_of(self,
>> + struct ns2_phy_driver, dev_nb);
>> +
>> + if (event) {
>> + pr_debug("Device connected\n");
>> + driver->data->new_state = EVT_DEVICE;
>> + schedule_delayed_work(&driver->conn_work, 0);
>> + } else {
>> + pr_debug("Device disconnected\n");
>> + driver->data->new_state = EVT_IDLE;
>> + schedule_delayed_work(&driver->conn_work, PHY_WQ_DELAY);
>> + }
>> +
>> + return NOTIFY_DONE;
>> +}
>> +
>> +static int drd_host_notify(struct notifier_block *self,
>> + unsigned long event, void *ptr)
>> +{
>> + struct ns2_phy_driver *driver = container_of(self,
>> + struct ns2_phy_driver, host_nb);
>> +
>> + if (event) {
>> + pr_debug("Host connected\n");
>> + driver->data->new_state = EVT_HOST;
>> + schedule_delayed_work(&driver->conn_work, 0);
>> + } else {
>> + pr_debug("Host disconnected\n");
>> + driver->data->new_state = EVT_IDLE;
>> + schedule_delayed_work(&driver->conn_work, PHY_WQ_DELAY);
>> + }
>> +
>> + return NOTIFY_DONE;
>> +}
>> +
>> +static void extcon_work(struct work_struct *work)
>> +{
>> + struct ns2_phy_driver *driver;
>> + int vbus;
>> + int id;
>> +
>> + driver = container_of(to_delayed_work(work),
>> + struct ns2_phy_driver, wq_extcon);
>> +
>> + id = gpiod_get_value_cansleep(driver->id_gpiod);
>> + vbus = gpiod_get_value_cansleep(driver->vbus_gpiod);
>> +
>> + if (!id && vbus) {
>> + extcon_set_cable_state_(driver->edev, EXTCON_USB_HOST, true);
>> + } else if (id && !vbus) {
>> + extcon_set_cable_state_(driver->edev, EXTCON_USB_HOST, false);
>> + extcon_set_cable_state_(driver->edev, EXTCON_USB, false);
>> + } else if (id && vbus) {
>> + extcon_set_cable_state_(driver->edev, EXTCON_USB, true);
>> + }
>> +}
>> +
>> +static irqreturn_t gpio_irq_handler(int irq, void *dev_id)
>> +{
>> + struct ns2_phy_driver *driver = dev_id;
>> +
>> + queue_delayed_work(system_power_efficient_wq, &driver->wq_extcon,
>> + driver->debounce_jiffies);
>> +
>> + return IRQ_HANDLED;
>> +}
>> +
>> +static int register_extcon_notifier(struct ns2_phy_driver *phy_driver,
>> + struct device *dev)
>> +{
>> + struct extcon_dev *edev;
>> + int ret;
>> +
>> + phy_driver->host_nb.notifier_call = drd_host_notify;
>> + phy_driver->dev_nb.notifier_call = drd_device_notify;
>> +
>> + edev = phy_driver->edev;
>> +
>> + /* Register for device change notification */
>> + ret = extcon_register_notifier(edev, EXTCON_USB,
>> + &phy_driver->dev_nb);
>> + if (ret < 0) {
>> + dev_err(dev, "can't register extcon_dev for %s\n", edev->name);
>> + return ret;
>> + }
>> +
>> + /* Register for host change notification */
>> + ret = extcon_register_notifier(edev, EXTCON_USB_HOST,
>> + &phy_driver->host_nb);
>> + if (ret < 0) {
>> + dev_err(dev, "can't register extcon_dev for %s\n", edev->name);
>> + goto err_dev;
>> + }
>> +
>> + /* Check the device cable connect state */
>> + ret = extcon_get_cable_state_(edev, EXTCON_USB);
>> + if (ret < 0) {
>> + dev_err(dev, "can't get extcon_dev state for %s\n", edev->name);
>> + goto err_host;
>> + } else if (ret) {
>> + phy_driver->data->new_state = EVT_DEVICE;
>> + }
>> +
>> + /* Check the host cable connect state */
>> + ret = extcon_get_cable_state_(edev, EXTCON_USB_HOST);
>> + if (ret < 0) {
>> + dev_err(dev, "can't get extcon_dev state for %s\n", edev->name);
>> + goto err_host;
>> + } else if (ret) {
>> + phy_driver->data->new_state = EVT_HOST;
>> + }
>> +
>> + return 0;
>> +
>> +err_host:
>> + ret = extcon_unregister_notifier(edev, EXTCON_USB_HOST,
>> + &phy_driver->host_nb);
>> +err_dev:
>> + ret = extcon_unregister_notifier(edev, EXTCON_USB,
>> + &phy_driver->dev_nb);
>> + return ret;
>> +}
>> +
>> +static struct phy_ops ops = {
>> + .init = ns2_drd_phy_init,
>
> Is this really being used by any controller driver? Can you point me to the
> controller driver that is using this driver?
This will be used by Synopsys UDC that's integrated into Broadcom's Northstar2
and Cygnus SoC's. I am currently working on upstream review comments for the
same in a different patch series. The "amd5536udc" driver is being modified for
platform device support (as per the suggestions I received in reviews).
>
>> + .power_on = ns2_drd_phy_poweron,
>> + .power_off = ns2_drd_phy_shutdown,
>
> missing .owner.
Will fix this.
Thanks,
Ravi
>
> Thanks
> Kishon
^ permalink raw reply [flat|nested] 20+ messages in thread
end of thread, other threads:[~2017-01-16 10:51 UTC | newest]
Thread overview: 20+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2016-11-30 5:55 [PATCH 0/3] Support for USB DRD Phy driver for NS2 Raviteja Garimella
2016-11-30 5:55 ` Raviteja Garimella
2016-11-30 5:55 ` Raviteja Garimella
2016-11-30 5:55 ` [PATCH 1/3] Add DT bindings documentation for NS2 USB DRD phy Raviteja Garimella
2016-11-30 5:55 ` Raviteja Garimella
2016-11-30 5:55 ` Raviteja Garimella
2016-12-05 23:09 ` Rob Herring
2016-12-05 23:09 ` Rob Herring
2016-12-05 23:09 ` Rob Herring
2016-11-30 5:55 ` [PATCH 2/3] Broadcom USB DRD Phy driver for Northstar2 Raviteja Garimella
2016-11-30 5:55 ` Raviteja Garimella
2016-11-30 5:55 ` Raviteja Garimella
2017-01-16 9:22 ` Kishon Vijay Abraham I
2017-01-16 9:22 ` Kishon Vijay Abraham I
2017-01-16 9:22 ` Kishon Vijay Abraham I
2017-01-16 10:51 ` Raviteja Garimella
2017-01-16 10:51 ` Raviteja Garimella
2017-01-16 10:51 ` Raviteja Garimella
2016-11-30 5:55 ` [PATCH 3/3] DT nodes for Broadcom Northstar2 USB DRD Phy Raviteja Garimella
2016-11-30 5:55 ` Raviteja Garimella
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.