* [BUG] mpt2sas: driver init fails on kernel >=4.2 for 9211-8i IT @ 2016-03-20 20:14 Matthias Prager 2016-03-21 4:53 ` Sreekanth Reddy 0 siblings, 1 reply; 13+ messages in thread From: Matthias Prager @ 2016-03-20 20:14 UTC (permalink / raw) To: linux-scsi; +Cc: Matthias Prager Hello, I don't know what's the correct procedure, whether I should file a bug or first report this issue on the kernel mailing-list. So please feel free to tell me to open a ticket in the bugtracker (bugzilla.kernel.org?). But first let me present the issue I encounter: Kernels >= 4.2 (4.2.1 was the first on I tried, but also 4.3, 4.4 and 4.5) fail to load the mpt2sas driver on most (but not all) boots. Kernels <= 4.1.x work fine every single time (4.1.19 was the latest I tried, also 3.18.29). Here is the dmesg output for a failed driver init with Kernel 4.5.0: > [ 2.068313] mpt3sas version 09.102.00.00 loaded > [ 2.069412] mpt2sas_cm0: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3074748 kB) > [ 2.125260] mpt2sas_cm0: MSI-X vectors supported: 1, no of cores: 4, max_msix_vectors: -1 > [ 2.125996] mpt2sas0-msix0: PCI-MSI-X enabled: IRQ 58 > [ 2.126199] mpt2sas_cm0: iomem(0x00000000fd4fc000), mapped(0xffffc900000d0000), size(16384) > [ 2.126430] mpt2sas_cm0: ioport(0x0000000000004000), size(256) > [ 2.216371] mpt2sas_cm0: Allocated physical memory: size(4964 kB) > [ 2.216600] mpt2sas_cm0: Current Controller Queue Depth(3307),Max Controller Queue Depth(3432) > [ 2.217004] mpt2sas_cm0: Scatter Gather Elements per IO(128) > [ 5.086959] floppy0: no floppy controllers found > [ 32.256720] mpt2sas_cm0: _base_event_notification: timeout > [ 32.256940] mf: > > [ 32.257106] 07000000 > [ 32.257302] 00000000 > [ 32.257337] 00000000 > [ 32.257533] 00000000 > [ 32.257568] 00000000 > [ 32.257764] 0f2f7fff > [ 32.257800] ffffff7c > [ 32.257995] ffffffff > [ 32.258031] > > [ 32.258352] ffffffff > [ 32.258387] 00000000 > [ 32.258582] 00000000 > > [ 32.258950] mpt2sas_cm0: sending message unit reset !! > [ 32.260688] mpt2sas_cm0: message unit reset: SUCCESS > [ 32.325956] mpt2sas_cm0: failure at drivers/scsi/mpt3sas/mpt3sas_scsih.c:8592/_scsih_probe()! For comparison here is a dmesg output for a successful boot on Kernel 4.1.15: > [ 2.035568] mpt2sas version 20.100.00.00 loaded > [ 2.037243] mpt2sas0: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (2046352 kB) > [ 2.755374] mpt2sas0: MSI-X vectors supported: 1, no of cores: 3, max_msix_vectors: 8 > [ 2.756377] mpt2sas0-msix0: PCI-MSI-X enabled: IRQ 58 > [ 2.756708] mpt2sas0: iomem(0x00000000fd5fc000), mapped(0xffffc900000d0000), size(16384) > [ 2.757083] mpt2sas0: ioport(0x0000000000004000), size(256) > [ 3.842944] mpt2sas0: Allocated physical memory: size(4964 kB) > [ 3.843303] mpt2sas0: Current Controller Queue Depth(3307), Max Controller Queue Depth(3432) > [ 3.843717] mpt2sas0: Scatter Gather Elements per IO(128) > [ 4.415980] mpt2sas0: LSISAS2008: FWVersion(20.00.04.00), ChipRevision(0x03), BiosVersion(07.39.00.00) > [ 4.416618] mpt2sas0: Protocol=(Initiator,Target), Capabilities=(TLR,EEDP,Snapshot Buffer,Diag Trace Buffer,Task Set Full,NCQ) > [ 4.417846] scsi host0: Fusion MPT SAS Host > [ 4.436865] mpt2sas0: sending port enable !! > [ 4.440460] mpt2sas0: host_add: handle(0x0001), sas_addr(0xxxxxxxxxxxxxxxxx), phys(8) > > ... > [ 4.444045] scsi 0:0:0:0: Direct-Access ATA Hitachi HDS5C302 A800 PQ: 0 ANSI: 6 > [ 4.444338] scsi 0:0:0:0: SATA: handle(0x0009), sas_addr(0xxxxxxxxxxxxxxxxx), phy(1), device_name(0xxxxxxxxxxxxxxxxx) > [ 4.444823] scsi 0:0:0:0: SATA: enclosure_logical_id(0xxxxxxxxxxxxxxxxx), slot(2) > [ 4.445197] scsi 0:0:0:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) > ... (n times for n drives) > > [ 4.515443] mpt2sas0: port enable: SUCCESS The Controller(s) are all Avego/LSI 9211-8i running the latest version of IT firmware (v20.00.04.00). These are passed through to a gentoo-linux VM on an ESXi 5.1 host (latest patchlevel). I have two of these systems (one production one testing) with nearly identical hardware (Supermicro X8DTi-F boards with 2x Intel Westmere CPUs). I also have an older set of systems running the same software config (Intel S3200SHLC boards with single Core2Quad) which exhibit the same buggy behavior. The 'uname -a' line on the current testing system looks like this: > Linux pserver2 4.1.19-gentoo #4 SMP Thu Mar 17 16:02:48 CET 2016 x86_64 Intel(R) Xeon(R) CPU E5506 @ 2.13GHz GenuineIntel GNU/Linux p There seem to be other people with similar issues: <https://bbs.archlinux.org/viewtopic.php?id=209495> Any thoughts? --- Matthias ^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [BUG] mpt2sas: driver init fails on kernel >=4.2 for 9211-8i IT 2016-03-20 20:14 [BUG] mpt2sas: driver init fails on kernel >=4.2 for 9211-8i IT Matthias Prager @ 2016-03-21 4:53 ` Sreekanth Reddy 2016-03-21 9:18 ` Matthias Prager 0 siblings, 1 reply; 13+ messages in thread From: Sreekanth Reddy @ 2016-03-21 4:53 UTC (permalink / raw) To: Matthias Prager; +Cc: linux-scsi Hi Matthias, Can you please share us the driver logs with driver logging_level set to 0x3f8. So that we can get more info from this log. Thanks, Sreekanth On Mon, Mar 21, 2016 at 1:44 AM, Matthias Prager <linux@matthiasprager.de> wrote: > Hello, > > I don't know what's the correct procedure, whether I should file a bug or first report this issue on the kernel mailing-list. So please feel free to tell me to open a ticket in the bugtracker (bugzilla.kernel.org?). > > But first let me present the issue I encounter: > > Kernels >= 4.2 (4.2.1 was the first on I tried, but also 4.3, 4.4 and 4.5) fail to load the mpt2sas driver on most (but not all) boots. Kernels <= 4.1.x work fine every single time (4.1.19 was the latest I tried, also 3.18.29). > > Here is the dmesg output for a failed driver init with Kernel 4.5.0: >> [ 2.068313] mpt3sas version 09.102.00.00 loaded >> [ 2.069412] mpt2sas_cm0: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3074748 kB) >> [ 2.125260] mpt2sas_cm0: MSI-X vectors supported: 1, no of cores: 4, max_msix_vectors: -1 >> [ 2.125996] mpt2sas0-msix0: PCI-MSI-X enabled: IRQ 58 >> [ 2.126199] mpt2sas_cm0: iomem(0x00000000fd4fc000), mapped(0xffffc900000d0000), size(16384) >> [ 2.126430] mpt2sas_cm0: ioport(0x0000000000004000), size(256) >> [ 2.216371] mpt2sas_cm0: Allocated physical memory: size(4964 kB) >> [ 2.216600] mpt2sas_cm0: Current Controller Queue Depth(3307),Max Controller Queue Depth(3432) >> [ 2.217004] mpt2sas_cm0: Scatter Gather Elements per IO(128) >> [ 5.086959] floppy0: no floppy controllers found >> [ 32.256720] mpt2sas_cm0: _base_event_notification: timeout >> [ 32.256940] mf: >> >> [ 32.257106] 07000000 >> [ 32.257302] 00000000 >> [ 32.257337] 00000000 >> [ 32.257533] 00000000 >> [ 32.257568] 00000000 >> [ 32.257764] 0f2f7fff >> [ 32.257800] ffffff7c >> [ 32.257995] ffffffff >> [ 32.258031] >> >> [ 32.258352] ffffffff >> [ 32.258387] 00000000 >> [ 32.258582] 00000000 >> >> [ 32.258950] mpt2sas_cm0: sending message unit reset !! >> [ 32.260688] mpt2sas_cm0: message unit reset: SUCCESS >> [ 32.325956] mpt2sas_cm0: failure at drivers/scsi/mpt3sas/mpt3sas_scsih.c:8592/_scsih_probe()! > > For comparison here is a dmesg output for a successful boot on Kernel 4.1.15: >> [ 2.035568] mpt2sas version 20.100.00.00 loaded >> [ 2.037243] mpt2sas0: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (2046352 kB) >> [ 2.755374] mpt2sas0: MSI-X vectors supported: 1, no of cores: 3, max_msix_vectors: 8 >> [ 2.756377] mpt2sas0-msix0: PCI-MSI-X enabled: IRQ 58 >> [ 2.756708] mpt2sas0: iomem(0x00000000fd5fc000), mapped(0xffffc900000d0000), size(16384) >> [ 2.757083] mpt2sas0: ioport(0x0000000000004000), size(256) >> [ 3.842944] mpt2sas0: Allocated physical memory: size(4964 kB) >> [ 3.843303] mpt2sas0: Current Controller Queue Depth(3307), Max Controller Queue Depth(3432) >> [ 3.843717] mpt2sas0: Scatter Gather Elements per IO(128) >> [ 4.415980] mpt2sas0: LSISAS2008: FWVersion(20.00.04.00), ChipRevision(0x03), BiosVersion(07.39.00.00) >> [ 4.416618] mpt2sas0: Protocol=(Initiator,Target), Capabilities=(TLR,EEDP,Snapshot Buffer,Diag Trace Buffer,Task Set Full,NCQ) >> [ 4.417846] scsi host0: Fusion MPT SAS Host >> [ 4.436865] mpt2sas0: sending port enable !! >> [ 4.440460] mpt2sas0: host_add: handle(0x0001), sas_addr(0xxxxxxxxxxxxxxxxx), phys(8) >> >> ... >> [ 4.444045] scsi 0:0:0:0: Direct-Access ATA Hitachi HDS5C302 A800 PQ: 0 ANSI: 6 >> [ 4.444338] scsi 0:0:0:0: SATA: handle(0x0009), sas_addr(0xxxxxxxxxxxxxxxxx), phy(1), device_name(0xxxxxxxxxxxxxxxxx) >> [ 4.444823] scsi 0:0:0:0: SATA: enclosure_logical_id(0xxxxxxxxxxxxxxxxx), slot(2) >> [ 4.445197] scsi 0:0:0:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >> ... (n times for n drives) >> >> [ 4.515443] mpt2sas0: port enable: SUCCESS > > > The Controller(s) are all Avego/LSI 9211-8i running the latest version of IT firmware (v20.00.04.00). These are passed through to a gentoo-linux VM on an ESXi 5.1 host (latest patchlevel). I have two of these systems (one production one testing) with nearly identical hardware (Supermicro X8DTi-F boards with 2x Intel Westmere CPUs). I also have an older set of systems running the same software config (Intel S3200SHLC boards with single Core2Quad) which exhibit the same buggy behavior. > > The 'uname -a' line on the current testing system looks like this: >> Linux pserver2 4.1.19-gentoo #4 SMP Thu Mar 17 16:02:48 CET 2016 x86_64 Intel(R) Xeon(R) CPU E5506 @ 2.13GHz GenuineIntel GNU/Linux > p > > There seem to be other people with similar issues: > <https://bbs.archlinux.org/viewtopic.php?id=209495> > > Any thoughts? > > --- > Matthias ^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [BUG] mpt2sas: driver init fails on kernel >=4.2 for 9211-8i IT 2016-03-21 4:53 ` Sreekanth Reddy @ 2016-03-21 9:18 ` Matthias Prager 2016-03-21 13:59 ` Sreekanth Reddy 0 siblings, 1 reply; 13+ messages in thread From: Matthias Prager @ 2016-03-21 9:18 UTC (permalink / raw) To: Sreekanth Reddy; +Cc: linux-scsi Hi Sreekanth, thank you for replying so quickly. Here are the logs you requested (kernel 4.5.0): > [ 2.083177] mpt3sas version 09.102.00.00 loaded > [ 2.083757] mpt2sas_cm0: mpt3sas_base_attach > [ 2.083956] mpt2sas_cm0: mpt3sas_base_map_resources > [ 2.084708] mpt2sas_cm0: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3074748 kB) > [ 2.084964] mpt2sas_cm0: _base_get_ioc_facts > [ 2.085154] mpt2sas_cm0: _base_wait_for_iocstate > [ 2.140893] offset:data > [ 2.141082] [0x00]:03100200 > [ 2.141257] [0x04]:00002300 > [ 2.141432] [0x08]:00000000 > [ 2.141606] [0x0c]:00000000 > [ 2.141780] [0x10]:00000000 > [ 2.141955] [0x14]:00010480 > [ 2.142129] [0x18]:22130d68 > [ 2.142303] [0x1c]:0001285c > [ 2.142477] [0x20]:14000400 > [ 2.142651] [0x24]:00000020 > [ 2.142825] [0x28]:0100000f > [ 2.143000] [0x2c]:000c000b > [ 2.143174] [0x30]:003c0003 > [ 2.143349] [0x34]:0020ffe0 > [ 2.143544] [0x38]:00800122 > [ 2.143719] [0x3c]:00000009 > [ 2.143895] mpt2sas_cm0: hba queue depth(3432), max chains per io(128) > [ 2.144106] mpt2sas_cm0: request frame size(128), reply frame size(128) > [ 2.144397] mpt2sas_cm0: msix is supported, vector_count(1) > [ 2.144600] mpt2sas_cm0: MSI-X vectors supported: 1, no of cores: 4, max_msix_vectors: -1 > [ 2.145161] mpt2sas0-msix0: PCI-MSI-X enabled: IRQ 58 > [ 2.145361] mpt2sas_cm0: iomem(0x00000000fd4fc000), mapped(0xffffc900000d0000), size(16384) > [ 2.145591] mpt2sas_cm0: ioport(0x0000000000004000), size(256) > [ 2.146206] mpt2sas_cm0: _base_get_ioc_facts > [ 2.146397] mpt2sas_cm0: _base_wait_for_iocstate > [ 2.202087] offset:data > [ 2.202281] [0x00]:03100200 > [ 2.202456] [0x04]:00002300 > [ 2.202631] [0x08]:00000000 > [ 2.202805] [0x0c]:00000000 > [ 2.202980] [0x10]:00000000 > [ 2.203154] [0x14]:00010480 > [ 2.203328] [0x18]:22130d68 > [ 2.203521] [0x1c]:0001285c > [ 2.203695] [0x20]:14000400 > [ 2.203870] [0x24]:00000020 > [ 2.204044] [0x28]:0100000f > [ 2.204219] [0x2c]:000c000b > [ 2.204394] [0x30]:003c0003 > [ 2.204571] [0x34]:0020ffe0 > [ 2.204746] [0x38]:00800122 > [ 2.204926] [0x3c]:00000009 > [ 2.205102] mpt2sas_cm0: hba queue depth(3432), max chains per io(128) > [ 2.205314] mpt2sas_cm0: request frame size(128), reply frame size(128) > [ 2.205528] mpt2sas_cm0: _base_make_ioc_ready > [ 2.205719] mpt2sas_cm0: _base_get_port_facts > [ 2.234205] offset:data > [ 2.234397] [0x00]:05070000 > [ 2.234573] [0x04]:00000000 > [ 2.234748] [0x08]:00000000 > [ 2.234928] [0x0c]:00000000 > [ 2.235103] [0x10]:00000000 > [ 2.235278] [0x14]:00003000 > [ 2.235453] [0x18]:00000078 > [ 2.235629] mpt2sas_cm0: _base_allocate_memory_pools > [ 2.235826] mpt2sas_cm0: scatter gather: sge_in_main_msg(3), sge_per_chain(15), sge_per_io(128), chains_per_io(9) > [ 2.236227] mpt2sas_cm0: reply post free pool (0xffff8800bb380000): depth(6944),element_size(8), pool_size(54 kB) > [ 2.236611] mpt2sas_cm0: reply_post_free_dma = (0xbb380000) > [ 2.236813] mpt2sas_cm0: scsi host: can_queue depth (3307) > [ 2.237086] mpt2sas_cm0: request pool(0xffff8800ba880000): depth(3432), frame_size(128), pool_size(429 kB) > [ 2.238580] mpt2sas_cm0: request pool: dma(0xba880000) > [ 2.238781] mpt2sas_cm0: scsiio(0xffff8800ba880000): depth(3307) > [ 2.243644] mpt2sas_cm0: chain pool depth(29763), frame_size(128), pool_size(3720 kB) > [ 2.243887] mpt2sas_cm0: hi_priority(0xffff8800ba8e7600): depth(60), start smid(3308) > [ 2.244113] mpt2sas_cm0: internal(0xffff8800ba8e9400): depth(65), start smid(3368) > [ 2.244390] mpt2sas_cm0: sense pool(0xffff8800ba480000): depth(3307), element_size(96), pool_size(310 kB) > [ 2.244774] mpt2sas_cm0: sense_dma(0xba480000) > [ 2.245038] mpt2sas_cm0: reply pool(0xffff8800ba500000): depth(3496), frame_size(128), pool_size(437 kB) > [ 2.245413] mpt2sas_cm0: reply_dma(0xba500000) > [ 2.245608] mpt2sas_cm0: reply_free pool(0xffff8800ba430000): depth(3496), element_size(4), pool_size(13 kB) > [ 2.245985] mpt2sas_cm0: reply_free_dma (0xba430000) > [ 2.246181] mpt2sas_cm0: config page(0xffff8800ba429000): size(512) > [ 2.246389] mpt2sas_cm0: config_page_dma(0xba429000) > [ 2.246584] mpt2sas_cm0: Allocated physical memory: size(4964 kB) > [ 2.246791] mpt2sas_cm0: Current Controller Queue Depth(3307),Max Controller Queue Depth(3432) > [ 2.247155] mpt2sas_cm0: Scatter Gather Elements per IO(128) > [ 2.247361] mpt2sas_cm0: _base_make_ioc_operational > [ 2.247962] mpt2sas_cm0: _base_send_ioc_init > [ 2.248154] offset:data > [ 2.248325] [0x00]:02000004 > [ 2.248499] [0x04]:00000000 > [ 2.248673] [0x08]:00000000 > [ 2.248848] [0x0c]:23000200 > [ 2.249023] [0x10]:00000000 > [ 2.249197] [0x14]:00000000 > [ 2.249372] [0x18]:00200000 > [ 2.249546] [0x1c]:0da81b20 > [ 2.249720] [0x20]:00000000 > [ 2.249894] [0x24]:00000000 > [ 2.250068] [0x28]:ba880000 > [ 2.250242] [0x2c]:00000000 > [ 2.250416] [0x30]:bb380000 > [ 2.250589] [0x34]:00000000 > [ 2.250768] [0x38]:ba430000 > [ 2.250941] [0x3c]:00000000 > [ 2.251115] [0x40]:983eb686 > [ 2.251288] [0x44]:00000153 > [ 2.296610] offset:data > [ 2.296795] [0x00]:02050004 > [ 2.296969] [0x04]:00000000 > [ 2.297143] [0x08]:00000000 > [ 2.297318] [0x0c]:00000000 > [ 2.297493] [0x10]:00000000 > [ 2.297668] mpt2sas_cm0: _base_event_notification > [ 5.093707] floppy0: no floppy controllers found > [ 32.293619] mpt2sas_cm0: _base_event_notification: timeout > [ 32.293909] mf: > > [ 32.294132] 07000000 > [ 32.294397] 00000000 > [ 32.294445] 00000000 > [ 32.294719] 00000000 > [ 32.294767] 00000000 > [ 32.295031] 0f2f7fff > [ 32.295078] ffffff7c > [ 32.295342] ffffffff > [ 32.295389] > > [ 32.295823] ffffffff > [ 32.295871] 00000000 > [ 32.296134] 00000000 > > [ 32.296615] mpt2sas_cm0: mpt3sas_base_free_resources > [ 32.296880] mpt2sas_cm0: _base_make_ioc_ready > [ 32.297135] mpt2sas_cm0: sending message unit reset !! > [ 32.298941] mpt2sas_cm0: message unit reset: SUCCESS > [ 32.299212] mpt2sas_cm0: mpt3sas_base_unmap_resources > [ 32.300381] mpt2sas_cm0: _base_release_memory_pools > [ 32.300654] mpt2sas_cm0: request_pool(0xffff8800ba880000): free > [ 32.300934] mpt2sas_cm0: sense_pool(0xffff8800ba480000): free > [ 32.301211] mpt2sas_cm0: reply_pool(0xffff8800ba500000): free > [ 32.301485] mpt2sas_cm0: reply_free_pool(0xffff8800ba430000): free > [ 32.301774] mpt2sas_cm0: reply_post_free_pool(0xffff8800bb380000): free > [ 32.302061] mpt2sas_cm0: config_page(0xffff8800ba429000): free > [ 32.371097] mpt2sas_cm0: failure at drivers/scsi/mpt3sas/mpt3sas_scsih.c:8592/_scsih_probe()! > [ 32.371958] mpt2sas_cm1: mpt3sas_base_attach > [ 32.372154] mpt2sas_cm1: mpt3sas_base_map_resources > [ 32.372950] mpt2sas_cm1: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3074748 kB) > [ 32.373201] mpt2sas_cm1: _base_get_ioc_facts > [ 32.375261] mpt2sas_cm1: _base_wait_for_iocstate > [ 32.432012] offset:data > [ 32.432262] [0x00]:03100200 > [ 32.432499] [0x04]:00002300 > [ 32.432735] [0x08]:00000000 > [ 32.432971] [0x0c]:00000000 > [ 32.433206] [0x10]:00000000 > [ 32.433443] [0x14]:00010480 > [ 32.433701] [0x18]:22130d68 > [ 32.433937] [0x1c]:0001285c > [ 32.435434] [0x20]:14000400 > [ 32.435674] [0x24]:00000020 > [ 32.435909] [0x28]:0100000f > [ 32.436144] [0x2c]:000c000b > [ 32.436379] [0x30]:003c0003 > [ 32.436615] [0x34]:0020ffe0 > [ 32.436850] [0x38]:00800122 > [ 32.437085] [0x3c]:00000009 > [ 32.437322] mpt2sas_cm1: hba queue depth(3432), max chains per io(128) > [ 32.437607] mpt2sas_cm1: request frame size(128), reply frame size(128) > [ 32.438014] mpt2sas_cm1: msix is supported, vector_count(1) > [ 32.438288] mpt2sas_cm1: MSI-X vectors supported: 1, no of cores: 4, max_msix_vectors: 8 > [ 32.439101] mpt2sas1-msix0: PCI-MSI-X enabled: IRQ 58 > [ 32.439373] mpt2sas_cm1: iomem(0x00000000fd1fc000), mapped(0xffffc900000d8000), size(16384) > [ 32.439682] mpt2sas_cm1: ioport(0x0000000000007000), size(256) > [ 32.440504] mpt2sas_cm1: _base_get_ioc_facts > [ 32.440765] mpt2sas_cm1: _base_wait_for_iocstate > [ 32.499305] offset:data > [ 32.499557] [0x00]:03100200 > [ 32.499794] [0x04]:00002300 > [ 32.500031] [0x08]:00000000 > [ 32.500267] [0x0c]:00000000 > [ 32.500504] [0x10]:00000000 > [ 32.500740] [0x14]:00010480 > [ 32.500974] [0x18]:22130d68 > [ 32.501209] [0x1c]:0001285c > [ 32.501444] [0x20]:14000400 > [ 32.501687] [0x24]:00000020 > [ 32.501922] [0x28]:0100000f > [ 32.502157] [0x2c]:000c000b > [ 32.502391] [0x30]:003c0003 > [ 32.502626] [0x34]:0020ffe0 > [ 32.502862] [0x38]:00800122 > [ 32.503098] [0x3c]:00000009 > [ 32.503336] mpt2sas_cm1: hba queue depth(3432), max chains per io(128) > [ 32.503644] mpt2sas_cm1: request frame size(128), reply frame size(128) > [ 32.503933] mpt2sas_cm1: _base_make_ioc_ready > [ 32.504191] mpt2sas_cm1: _base_get_port_facts > [ 32.534282] offset:data > [ 32.534537] [0x00]:05070000 > [ 32.534782] [0x04]:00000000 > [ 32.535058] [0x08]:00000000 > [ 32.536473] [0x0c]:00000000 > [ 32.536710] [0x10]:00000000 > [ 32.536946] [0x14]:00003000 > [ 32.537183] [0x18]:00000078 > [ 32.537420] mpt2sas_cm1: _base_allocate_memory_pools > [ 32.537686] mpt2sas_cm1: scatter gather: sge_in_main_msg(3), sge_per_chain(15), sge_per_io(128), chains_per_io(9) > [ 32.538232] mpt2sas_cm1: reply post free pool (0xffff8800bb3d0000): depth(6944),element_size(8), pool_size(54 kB) > [ 32.538758] mpt2sas_cm1: reply_post_free_dma = (0xbb3d0000) > [ 32.539030] mpt2sas_cm1: scsi host: can_queue depth (3307) > [ 32.539378] mpt2sas_cm1: request pool(0xffff8800ba480000): depth(3432), frame_size(128), pool_size(429 kB) > [ 32.539882] mpt2sas_cm1: request pool: dma(0xba480000) > [ 32.540149] mpt2sas_cm1: scsiio(0xffff8800ba480000): depth(3307) > [ 32.545893] mpt2sas_cm1: chain pool depth(29763), frame_size(128), pool_size(3720 kB) > [ 32.546137] mpt2sas_cm1: hi_priority(0xffff8800ba4e7600): depth(60), start smid(3308) > [ 32.546365] mpt2sas_cm1: internal(0xffff8800ba4e9400): depth(65), start smid(3368) > [ 32.546651] mpt2sas_cm1: sense pool(0xffff8800ba880000): depth(3307), element_size(96), pool_size(310 kB) > [ 32.547030] mpt2sas_cm1: sense_dma(0xba880000) > [ 32.547537] mpt2sas_cm1: reply pool(0xffff880000100000): depth(3496), frame_size(128), pool_size(437 kB) > [ 32.547921] mpt2sas_cm1: reply_dma(0x100000) > [ 32.548117] mpt2sas_cm1: reply_free pool(0xffff8800ba964000): depth(3496), element_size(4), pool_size(13 kB) > [ 32.548500] mpt2sas_cm1: reply_free_dma (0xba964000) > [ 32.548698] mpt2sas_cm1: config page(0xffff8800ba960000): size(512) > [ 32.548908] mpt2sas_cm1: config_page_dma(0xba960000) > [ 32.549105] mpt2sas_cm1: Allocated physical memory: size(4964 kB) > [ 32.549314] mpt2sas_cm1: Current Controller Queue Depth(3307),Max Controller Queue Depth(3432) > [ 32.550950] mpt2sas_cm1: Scatter Gather Elements per IO(128) > [ 32.551160] mpt2sas_cm1: _base_make_ioc_operational > [ 32.551855] mpt2sas_cm1: _base_send_ioc_init > [ 32.552051] offset:data > [ 32.552224] [0x00]:02000004 > [ 32.552400] [0x04]:00000000 > [ 32.552576] [0x08]:00000000 > [ 32.552761] [0x0c]:23000200 > [ 32.552937] [0x10]:00000000 > [ 32.553114] [0x14]:00000000 > [ 32.553291] [0x18]:00200000 > [ 32.553468] [0x1c]:0da81b20 > [ 32.553685] [0x20]:00000000 > [ 32.553862] [0x24]:00000000 > [ 32.554038] [0x28]:ba480000 > [ 32.554215] [0x2c]:00000000 > [ 32.554393] [0x30]:bb3d0000 > [ 32.554569] [0x34]:00000000 > [ 32.554752] [0x38]:ba964000 > [ 32.554929] [0x3c]:00000000 > [ 32.555106] [0x40]:983f2ce6 > [ 32.555283] [0x44]:00000153 > [ 32.601516] offset:data > [ 32.601768] [0x00]:02050004 > [ 32.602003] [0x04]:00000000 > [ 32.602239] [0x08]:00000000 > [ 32.602474] [0x0c]:00000000 > [ 32.602709] [0x10]:00000000 > [ 32.602945] mpt2sas_cm1: _base_event_notification > [ 62.593604] mpt2sas_cm1: _base_event_notification: timeout > [ 62.593906] mf: > > [ 62.594127] 07000000 > [ 62.594390] 00000000 > [ 62.594438] 00000000 > [ 62.594709] 00000000 > [ 62.594757] 00000000 > [ 62.595019] 0f2f7fff > [ 62.595067] ffffff7c > [ 62.595330] ffffffff > [ 62.595377] > > [ 62.595808] ffffffff > [ 62.595855] 00000000 > [ 62.596117] 00000000 > > [ 62.596601] mpt2sas_cm1: mpt3sas_base_free_resources > [ 62.596871] mpt2sas_cm1: _base_make_ioc_ready > [ 62.597125] mpt2sas_cm1: sending message unit reset !! > [ 62.599013] mpt2sas_cm1: message unit reset: SUCCESS > [ 62.599283] mpt2sas_cm1: mpt3sas_base_unmap_resources > [ 62.600443] mpt2sas_cm1: _base_release_memory_pools > [ 62.600721] mpt2sas_cm1: request_pool(0xffff8800ba480000): free > [ 62.601002] mpt2sas_cm1: sense_pool(0xffff8800ba880000): free > [ 62.601280] mpt2sas_cm1: reply_pool(0xffff880000100000): free > [ 62.601560] mpt2sas_cm1: reply_free_pool(0xffff8800ba964000): free > [ 62.601845] mpt2sas_cm1: reply_post_free_pool(0xffff8800bb3d0000): free > [ 62.602133] mpt2sas_cm1: config_page(0xffff8800ba960000): free > [ 62.673591] mpt2sas_cm1: failure at drivers/scsi/mpt3sas/mpt3sas_scsih.c:8592/_scsih_probe()! These are for two controllers, I don't know whether the output from the second is helpful at all - I added it anyway. I managed to boot the same 4.5.0 kernel successfully after warm rebooting from 4.1.20. That gave me this dmesg output (for comparison): > [ 2.057685] mpt3sas version 09.102.00.00 loaded > [ 2.058371] mpt2sas_cm0: mpt3sas_base_attach > [ 2.058632] mpt2sas_cm0: mpt3sas_base_map_resources > [ 2.059583] mpt2sas_cm0: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3074748 kB) > [ 2.059911] mpt2sas_cm0: _base_get_ioc_facts > [ 2.060166] mpt2sas_cm0: _base_wait_for_iocstate > [ 2.116337] offset:data > [ 2.116576] [0x00]:03100200 > [ 2.116817] [0x04]:00002300 > [ 2.117051] [0x08]:00000000 > [ 2.117285] [0x0c]:00000000 > [ 2.117518] [0x10]:00000000 > [ 2.117752] [0x14]:00010480 > [ 2.117986] [0x18]:22130d68 > [ 2.118220] [0x1c]:0001285c > [ 2.119624] [0x20]:14000400 > [ 2.119858] [0x24]:00000020 > [ 2.120093] [0x28]:0100000f > [ 2.120351] [0x2c]:000c000b > [ 2.120586] [0x30]:003c0003 > [ 2.120820] [0x34]:0020ffe0 > [ 2.121055] [0x38]:00800122 > [ 2.121288] [0x3c]:00000009 > [ 2.121524] mpt2sas_cm0: hba queue depth(3432), max chains per io(128) > [ 2.121808] mpt2sas_cm0: request frame size(128), reply frame size(128) > [ 2.122195] mpt2sas_cm0: msix is supported, vector_count(1) > [ 2.122468] mpt2sas_cm0: MSI-X vectors supported: 1, no of cores: 4, max_msix_vectors: -1 > [ 2.123239] mpt2sas0-msix0: PCI-MSI-X enabled: IRQ 58 > [ 2.123507] mpt2sas_cm0: iomem(0x00000000fd4fc000), mapped(0xffffc900000d0000), size(16384) > [ 2.123816] mpt2sas_cm0: ioport(0x0000000000004000), size(256) > [ 2.124623] mpt2sas_cm0: _base_get_ioc_facts > [ 2.124878] mpt2sas_cm0: _base_wait_for_iocstate > [ 2.180907] offset:data > [ 2.181145] [0x00]:03100200 > [ 2.181379] [0x04]:00002300 > [ 2.181613] [0x08]:00000000 > [ 2.181847] [0x0c]:00000000 > [ 2.182081] [0x10]:00000000 > [ 2.182315] [0x14]:00010480 > [ 2.182547] [0x18]:22130d68 > [ 2.182781] [0x1c]:0001285c > [ 2.183014] [0x20]:14000400 > [ 2.183248] [0x24]:00000020 > [ 2.183481] [0x28]:0100000f > [ 2.183720] [0x2c]:000c000b > [ 2.183954] [0x30]:003c0003 > [ 2.184190] [0x34]:0020ffe0 > [ 2.184424] [0x38]:00800122 > [ 2.184658] [0x3c]:00000009 > [ 2.184893] mpt2sas_cm0: hba queue depth(3432), max chains per io(128) > [ 2.185177] mpt2sas_cm0: request frame size(128), reply frame size(128) > [ 2.185462] mpt2sas_cm0: _base_make_ioc_ready > [ 2.185717] mpt2sas_cm0: _base_get_port_facts > [ 2.214057] offset:data > [ 2.214295] [0x00]:05070000 > [ 2.214529] [0x04]:00000000 > [ 2.214762] [0x08]:00000000 > [ 2.214997] [0x0c]:00000000 > [ 2.215230] [0x10]:00000000 > [ 2.215464] [0x14]:00003000 > [ 2.215697] [0x18]:00000078 > [ 2.215931] mpt2sas_cm0: _base_allocate_memory_pools > [ 2.216194] mpt2sas_cm0: scatter gather: sge_in_main_msg(3), sge_per_chain(15), sge_per_io(128), chains_per_io(9) > [ 2.216734] mpt2sas_cm0: reply post free pool (0xffff8800bafc0000): depth(6944),element_size(8), pool_size(54 kB) > [ 2.217244] mpt2sas_cm0: reply_post_free_dma = (0xbafc0000) > [ 2.217514] mpt2sas_cm0: scsi host: can_queue depth (3307) > [ 2.217866] mpt2sas_cm0: request pool(0xffff8800ba800000): depth(3432), frame_size(128), pool_size(429 kB) > [ 2.218369] mpt2sas_cm0: request pool: dma(0xba800000) > [ 2.218637] mpt2sas_cm0: scsiio(0xffff8800ba800000): depth(3307) > [ 2.224773] mpt2sas_cm0: chain pool depth(29763), frame_size(128), pool_size(3720 kB) > [ 2.225092] mpt2sas_cm0: hi_priority(0xffff8800ba867600): depth(60), start smid(3308) > [ 2.225395] mpt2sas_cm0: internal(0xffff8800ba869400): depth(65), start smid(3368) > [ 2.225958] mpt2sas_cm0: sense pool(0xffff8800ba480000): depth(3307), element_size(96), pool_size(310 kB) > [ 2.226457] mpt2sas_cm0: sense_dma(0xba480000) > [ 2.227039] mpt2sas_cm0: reply pool(0xffff8800ba500000): depth(3496), frame_size(128), pool_size(437 kB) > [ 2.227413] mpt2sas_cm0: reply_dma(0xba500000) > [ 2.227616] mpt2sas_cm0: reply_free pool(0xffff8800ba450000): depth(3496), element_size(4), pool_size(13 kB) > [ 2.227992] mpt2sas_cm0: reply_free_dma (0xba450000) > [ 2.228192] mpt2sas_cm0: config page(0xffff8800ba43b000): size(512) > [ 2.228402] mpt2sas_cm0: config_page_dma(0xba43b000) > [ 2.228598] mpt2sas_cm0: Allocated physical memory: size(4964 kB) > [ 2.228806] mpt2sas_cm0: Current Controller Queue Depth(3307),Max Controller Queue Depth(3432) > [ 2.229171] mpt2sas_cm0: Scatter Gather Elements per IO(128) > [ 2.229378] mpt2sas_cm0: _base_make_ioc_operational > [ 2.229959] mpt2sas_cm0: _base_send_ioc_init > [ 2.230151] offset:data > [ 2.230323] [0x00]:02000004 > [ 2.230499] [0x04]:00000000 > [ 2.230675] [0x08]:00000000 > [ 2.230851] [0x0c]:23000200 > [ 2.231026] [0x10]:00000000 > [ 2.231201] [0x14]:00000000 > [ 2.231376] [0x18]:00200000 > [ 2.231551] [0x1c]:0da81b20 > [ 2.231726] [0x20]:00000000 > [ 2.231900] [0x24]:00000000 > [ 2.232075] [0x28]:ba800000 > [ 2.232250] [0x2c]:00000000 > [ 2.232423] [0x30]:bafc0000 > [ 2.232597] [0x34]:00000000 > [ 2.232775] [0x38]:ba450000 > [ 2.232950] [0x3c]:00000000 > [ 2.233125] [0x40]:98596e4f > [ 2.233299] [0x44]:00000153 > [ 2.278752] offset:data > [ 2.278988] [0x00]:02050004 > [ 2.279220] [0x04]:00000000 > [ 2.279453] [0x08]:00000000 > [ 2.279685] [0x0c]:00000000 > [ 2.279918] [0x10]:00000000 > [ 2.280151] mpt2sas_cm0: _base_event_notification > [ 2.280537] mpt2sas_cm0: _base_event_notification: complete > [ 2.281694] mpt2sas_cm0: LSISAS2008: FWVersion(20.00.04.00), ChipRevision(0x03), BiosVersion(07.39.00.00) > [ 2.282196] mpt2sas_cm0: Protocol=( > [ 2.282261] Initiator > [ 2.282522] ,Target > [ 2.282567] ), > [ 2.282824] Capabilities=( > [ 2.282877] TLR > [ 2.283132] ,EEDP > [ 2.283175] ,Snapshot Buffer > [ 2.283444] ,Diag Trace Buffer > [ 2.283502] ,Task Set Full > [ 2.283774] ,NCQ > [ 2.283816] ) > [ 2.284350] scsi host0: Fusion MPT SAS Host > [ 2.299028] mpt2sas_cm0: sending port enable !! > [ 2.299540] mpt2sas_cm0: Discovery: (start) > > [ 2.299972] mpt2sas_cm0: SAS Enclosure Device Status Change > [ 2.299984] mpt2sas_cm0: discovery event: (start) > > [ 2.300554] mpt2sas_cm0: SAS Topology Change List > [ 2.300759] mpt2sas_cm0: Discovery: (stop) > > [ 2.301146] mpt2sas_cm0: Discovery: (start) > > [ 2.301535] mpt2sas_cm0: Discovery: (stop) > > [ 2.301927] mpt2sas_cm0: Discovery: (start) > > [ 2.302316] mpt2sas_cm0: Discovery: (stop) > > [ 2.302707] mpt2sas_cm0: Discovery: (start) > > [ 2.304908] mpt2sas_cm0: Discovery: (stop) > > [ 2.305297] mpt2sas_cm0: Discovery: (start) > > [ 2.306776] mpt2sas_cm0: Discovery: (stop) > > [ 2.307166] mpt2sas_cm0: Discovery: (start) > > [ 2.307559] mpt2sas_cm0: Discovery: (stop) > > [ 2.307948] mpt2sas_cm0: Discovery: (start) > > [ 2.308336] mpt2sas_cm0: Discovery: (stop) > > [ 2.311738] mpt2sas_cm0: host_add: handle(0x0001), sas_addr(0x500605b003683dd0), phys(8) > [ 2.312097] mpt2sas_cm0: enclosure status change: (enclosure add) > handle(0x0001), enclosure logical id(0x500605b003683dd0) number slots(0) > [ 2.312551] mpt2sas_cm0: sas topology change: (responding) > [ 2.312768] handle(0x0000), enclosure_handle(0x0001) start_phy(00), count(8) > [ 2.313003] phy(01), attached_handle(0x0009): target add: link rate: new(0x0a), old(0x00) > [ 2.313250] phy(02), attached_handle(0x000a): target add: link rate: new(0x09), old(0x00) > [ 2.313498] phy(03), attached_handle(0x000b): target add: link rate: new(0x09), old(0x00) > [ 2.313745] phy(04), attached_handle(0x000c): target add: link rate: new(0x09), old(0x00) > [ 2.313992] phy(05), attached_handle(0x000d): target add: link rate: new(0x09), old(0x00) > [ 2.314248] phy(06), attached_handle(0x000e): target add: link rate: new(0x09), old(0x00) > [ 2.314495] phy(07), attached_handle(0x000f): target add: link rate: new(0x09), old(0x00) > [ 2.314747] mpt2sas_cm0: updating handles for sas_host(0x500605b003683dd0) > [ 2.316041] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x0009), sas_addr(0x4433221101000000) > [ 2.316465] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 2) > [ 2.317200] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000a), sas_addr(0x4433221102000000) > [ 2.317669] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 1) > [ 2.318431] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000b), sas_addr(0x4433221103000000) > [ 2.318900] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 0) > [ 2.319366] mpt2sas_cm0: _scsih_determine_boot_device: current_boot_device(0x4433221103000000) > [ 2.320151] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000c), sas_addr(0x4433221104000000) > [ 2.321371] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 7) > [ 2.322137] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000d), sas_addr(0x4433221105000000) > [ 2.322606] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 6) > [ 2.323367] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000e), sas_addr(0x4433221106000000) > [ 2.323834] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 5) > [ 2.324602] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000f), sas_addr(0x4433221107000000) > [ 2.325071] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 4) > [ 2.325541] mpt2sas_cm0: discovery event: (stop) > > [ 2.326017] mpt2sas_cm0: discovery event: (start) > > [ 2.326492] mpt2sas_cm0: discovery event: (stop) > > [ 2.326975] mpt2sas_cm0: discovery event: (start) > > [ 2.327450] mpt2sas_cm0: discovery event: (stop) > > [ 2.327923] mpt2sas_cm0: discovery event: (start) > > [ 2.328396] mpt2sas_cm0: discovery event: (stop) > > [ 2.328868] mpt2sas_cm0: discovery event: (start) > > [ 2.329340] mpt2sas_cm0: discovery event: (stop) > > [ 2.329816] mpt2sas_cm0: discovery event: (start) > > [ 2.330316] mpt2sas_cm0: discovery event: (stop) > > [ 2.330797] mpt2sas_cm0: discovery event: (start) > > [ 2.331269] mpt2sas_cm0: discovery event: (stop) > > [ 2.331740] mpt2sas_cm0: port enable: complete from worker thread > [ 2.350236] mpt2sas_cm0: port enable: SUCCESS > [ 2.356432] scsi 0:0:0:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 > [ 2.356683] scsi 0:0:0:0: SATA: handle(0x000b), sas_addr(0x4433221103000000), phy(3), device_name(0x5000c5000267c9f8) > [ 2.357080] scsi 0:0:0:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(0) > [ 2.357405] scsi 0:0:0:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) > [ 2.383043] scsi 0:0:1:0: Direct-Access ATA Hitachi HDS5C302 A800 PQ: 0 ANSI: 6 > [ 2.383296] scsi 0:0:1:0: SATA: handle(0x0009), sas_addr(0x4433221101000000), phy(1), device_name(0x5000cca369cdd311) > [ 2.383684] scsi 0:0:1:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(2) > [ 2.384028] scsi 0:0:1:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) > [ 2.405088] scsi 0:0:2:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 > [ 2.405346] scsi 0:0:2:0: SATA: handle(0x000a), sas_addr(0x4433221102000000), phy(2), device_name(0x5000c5000ccfbd32) > [ 2.405735] scsi 0:0:2:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(1) > [ 2.406082] scsi 0:0:2:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) > [ 2.424125] scsi 0:0:3:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 > [ 2.424373] scsi 0:0:3:0: SATA: handle(0x000c), sas_addr(0x4433221104000000), phy(4), device_name(0x5000c5000267abee) > [ 2.424763] scsi 0:0:3:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(7) > [ 2.425108] scsi 0:0:3:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) > [ 2.444834] scsi 0:0:4:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 > [ 2.445086] scsi 0:0:4:0: SATA: handle(0x000d), sas_addr(0x4433221105000000), phy(5), device_name(0x5000c50009c0e5e6) > [ 2.445478] scsi 0:0:4:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(6) > [ 2.445803] scsi 0:0:4:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) > [ 2.464065] scsi 0:0:5:0: Direct-Access ATA ST3750330NS SN16 PQ: 0 ANSI: 6 > [ 2.464312] scsi 0:0:5:0: SATA: handle(0x000e), sas_addr(0x4433221106000000), phy(6), device_name(0x5000c5003cb9ac10) > [ 2.464699] scsi 0:0:5:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(5) > [ 2.465048] scsi 0:0:5:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) > [ 2.484016] scsi 0:0:6:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 > [ 2.484266] scsi 0:0:6:0: SATA: handle(0x000f), sas_addr(0x4433221107000000), phy(7), device_name(0x5000c5000839b69e) > [ 2.484655] scsi 0:0:6:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(4) > [ 2.485001] scsi 0:0:6:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) > [ 2.500660] mpt2sas_cm1: mpt3sas_base_attach > [ 2.500861] mpt2sas_cm1: mpt3sas_base_map_resources > [ 2.501599] mpt2sas_cm1: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3074748 kB) > [ 2.501847] mpt2sas_cm1: _base_get_ioc_facts > [ 2.502036] mpt2sas_cm1: _base_wait_for_iocstate > [ 2.559080] offset:data > [ 2.559318] [0x00]:03100200 > [ 2.559552] [0x04]:00002300 > [ 2.559785] [0x08]:00000000 > [ 2.560020] [0x0c]:00000000 > [ 2.560277] [0x10]:00000000 > [ 2.560511] [0x14]:00010480 > [ 2.560745] [0x18]:22130d68 > [ 2.560978] [0x1c]:0001285c > [ 2.561210] [0x20]:14000400 > [ 2.561443] [0x24]:00000020 > [ 2.561675] [0x28]:0100000f > [ 2.561907] [0x2c]:000c000b > [ 2.562139] [0x30]:003c0003 > [ 2.562371] [0x34]:0020ffe0 > [ 2.562602] [0x38]:00800122 > [ 2.562839] [0x3c]:00000009 > [ 2.563073] mpt2sas_cm1: hba queue depth(3432), max chains per io(128) > [ 2.563355] mpt2sas_cm1: request frame size(128), reply frame size(128) > [ 2.563745] mpt2sas_cm1: msix is supported, vector_count(1) > [ 2.564016] mpt2sas_cm1: MSI-X vectors supported: 1, no of cores: 4, max_msix_vectors: 8 > [ 2.564918] mpt2sas1-msix0: PCI-MSI-X enabled: IRQ 59 > [ 2.566189] mpt2sas_cm1: iomem(0x00000000fd1fc000), mapped(0xffffc900000d8000), size(16384) > [ 2.566498] mpt2sas_cm1: ioport(0x0000000000007000), size(256) > [ 2.567328] mpt2sas_cm1: _base_get_ioc_facts > [ 2.567583] mpt2sas_cm1: _base_wait_for_iocstate > [ 2.625125] offset:data > [ 2.625364] [0x00]:03100200 > [ 2.625597] [0x04]:00002300 > [ 2.625830] [0x08]:00000000 > [ 2.626064] [0x0c]:00000000 > [ 2.626296] [0x10]:00000000 > [ 2.626529] [0x14]:00010480 > [ 2.626769] [0x18]:22130d68 > [ 2.627002] [0x1c]:0001285c > [ 2.627235] [0x20]:14000400 > [ 2.627467] [0x24]:00000020 > [ 2.627702] [0x28]:0100000f > [ 2.627936] [0x2c]:000c000b > [ 2.628170] [0x30]:003c0003 > [ 2.628403] [0x34]:0020ffe0 > [ 2.628638] [0x38]:00800122 > [ 2.628872] [0x3c]:00000009 > [ 2.629107] mpt2sas_cm1: hba queue depth(3432), max chains per io(128) > [ 2.629388] mpt2sas_cm1: request frame size(128), reply frame size(128) > [ 2.629671] mpt2sas_cm1: _base_make_ioc_ready > [ 2.629928] mpt2sas_cm1: _base_get_port_facts > [ 2.660127] offset:data > [ 2.660389] [0x00]:05070000 > [ 2.660623] [0x04]:00000000 > [ 2.660858] [0x08]:00000000 > [ 2.661093] [0x0c]:00000000 > [ 2.661326] [0x10]:00000000 > [ 2.661562] [0x14]:00003000 > [ 2.661796] [0x18]:00000078 > [ 2.664346] mpt2sas_cm1: _base_allocate_memory_pools > [ 2.664608] mpt2sas_cm1: scatter gather: sge_in_main_msg(3), sge_per_chain(15), sge_per_io(128), chains_per_io(9) > [ 2.665142] mpt2sas_cm1: reply post free pool (0xffff8800b8b10000): depth(6944),element_size(8), pool_size(54 kB) > [ 2.666671] mpt2sas_cm1: reply_post_free_dma = (0xb8b10000) > [ 2.666954] mpt2sas_cm1: scsi host: can_queue depth (3307) > [ 2.667311] mpt2sas_cm1: request pool(0xffff8800b8b80000): depth(3432), frame_size(128), pool_size(429 kB) > [ 2.667813] mpt2sas_cm1: request pool: dma(0xb8b80000) > [ 2.668080] mpt2sas_cm1: scsiio(0xffff8800b8b80000): depth(3307) > [ 2.674131] mpt2sas_cm1: chain pool depth(29763), frame_size(128), pool_size(3720 kB) > [ 2.674448] mpt2sas_cm1: hi_priority(0xffff8800b8be7600): depth(60), start smid(3308) > [ 2.674750] mpt2sas_cm1: internal(0xffff8800b8be9400): depth(65), start smid(3368) > [ 2.675105] mpt2sas_cm1: sense pool(0xffff8800b8100000): depth(3307), element_size(96), pool_size(310 kB) > [ 2.675605] mpt2sas_cm1: sense_dma(0xb8100000) > [ 2.675944] mpt2sas_cm1: reply pool(0xffff8800b8180000): depth(3496), frame_size(128), pool_size(437 kB) > [ 2.676443] mpt2sas_cm1: reply_dma(0xb8180000) > [ 2.676702] mpt2sas_cm1: reply_free pool(0xffff8800b80a0000): depth(3496), element_size(4), pool_size(13 kB) > [ 2.677124] mpt2sas_cm1: reply_free_dma (0xb80a0000) > [ 2.677322] mpt2sas_cm1: config page(0xffff8800b807f000): size(512) > [ 2.677532] mpt2sas_cm1: config_page_dma(0xb807f000) > [ 2.677728] mpt2sas_cm1: Allocated physical memory: size(4964 kB) > [ 2.677936] mpt2sas_cm1: Current Controller Queue Depth(3307),Max Controller Queue Depth(3432) > [ 2.678304] mpt2sas_cm1: Scatter Gather Elements per IO(128) > [ 2.678514] mpt2sas_cm1: _base_make_ioc_operational > [ 2.679081] mpt2sas_cm1: _base_send_ioc_init > [ 2.679275] offset:data > [ 2.679448] [0x00]:02000004 > [ 2.679625] [0x04]:00000000 > [ 2.679805] [0x08]:00000000 > [ 2.681200] [0x0c]:23000200 > [ 2.681377] [0x10]:00000000 > [ 2.681554] [0x14]:00000000 > [ 2.681729] [0x18]:00200000 > [ 2.681906] [0x1c]:0da81b20 > [ 2.682082] [0x20]:00000000 > [ 2.682259] [0x24]:00000000 > [ 2.682435] [0x28]:b8b80000 > [ 2.682611] [0x2c]:00000000 > [ 2.682787] [0x30]:b8b10000 > [ 2.682963] [0x34]:00000000 > [ 2.683139] [0x38]:b80a0000 > [ 2.683314] [0x3c]:00000000 > [ 2.683489] [0x40]:98597011 > [ 2.683665] [0x44]:00000153 > [ 2.729849] offset:data > [ 2.730089] [0x00]:02050004 > [ 2.730349] [0x04]:00000000 > [ 2.730586] [0x08]:00000000 > [ 2.730822] [0x0c]:00000000 > [ 2.731058] [0x10]:00000000 > [ 2.731295] mpt2sas_cm1: _base_event_notification > [ 2.731606] mpt2sas_cm1: _base_event_notification: complete > [ 2.732501] mpt2sas_cm1: LSISAS2008: FWVersion(20.00.04.00), ChipRevision(0x02), BiosVersion(07.39.00.00) > [ 2.733010] mpt2sas_cm1: Protocol=( > [ 2.733074] Initiator > [ 2.733339] ,Target > [ 2.733384] ), > [ 2.733642] Capabilities=( > [ 2.733696] TLR > [ 2.733952] ,EEDP > [ 2.733995] ,Snapshot Buffer > [ 2.734268] ,Diag Trace Buffer > [ 2.734326] ,Task Set Full > [ 2.734595] ,NCQ > [ 2.734637] ) > [ 2.735155] scsi host1: Fusion MPT SAS Host > [ 2.749047] mpt2sas_cm1: sending port enable !! > [ 2.749563] mpt2sas_cm1: Discovery: (start) > > [ 2.749989] mpt2sas_cm1: SAS Enclosure Device Status Change > [ 2.750001] mpt2sas_cm1: discovery event: (start) > > [ 2.750578] mpt2sas_cm1: SAS Topology Change List > [ 2.750788] mpt2sas_cm1: Discovery: (stop) > > [ 2.751181] mpt2sas_cm1: Discovery: (start) > > [ 2.751571] mpt2sas_cm1: Discovery: (stop) > > [ 2.752002] mpt2sas_cm1: Discovery: (start) > > [ 2.752391] mpt2sas_cm1: Discovery: (stop) > > [ 2.752779] mpt2sas_cm1: Discovery: (start) > > [ 2.754205] mpt2sas_cm1: Discovery: (stop) > > [ 2.754593] mpt2sas_cm1: Discovery: (start) > > [ 2.754983] mpt2sas_cm1: Discovery: (stop) > > [ 2.755371] mpt2sas_cm1: Discovery: (start) > > [ 2.755762] mpt2sas_cm1: Discovery: (stop) > > [ 2.759602] mpt2sas_cm1: host_add: handle(0x0001), sas_addr(0x500605b0026f79b0), phys(8) > [ 2.759969] mpt2sas_cm1: enclosure status change: (enclosure add) > handle(0x0001), enclosure logical id(0x500605b0026f79b0) number slots(0) > [ 2.760407] mpt2sas_cm1: sas topology change: (responding) > [ 2.760612] handle(0x0000), enclosure_handle(0x0001) start_phy(00), count(8) > [ 2.760834] phy(02), attached_handle(0x000e): target add: link rate: new(0x0a), old(0x00) > [ 2.761066] phy(03), attached_handle(0x000b): target add: link rate: new(0x0a), old(0x00) > [ 2.761304] phy(04), attached_handle(0x000d): target add: link rate: new(0x09), old(0x00) > [ 2.761538] phy(05), attached_handle(0x0009): target add: link rate: new(0x09), old(0x00) > [ 2.761771] phy(06), attached_handle(0x000a): target add: link rate: new(0x09), old(0x00) > [ 2.762002] phy(07), attached_handle(0x000c): target add: link rate: new(0x09), old(0x00) > [ 2.762235] mpt2sas_cm1: updating handles for sas_host(0x500605b0026f79b0) > [ 2.763653] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x000e), sas_addr(0x4433221102000000) > [ 2.764036] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 1) > [ 2.764772] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x000b), sas_addr(0x4433221103000000) > [ 2.765147] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 0) > [ 2.765891] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x000d), sas_addr(0x4433221104000000) > [ 2.767250] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 7) > [ 2.768009] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x0009), sas_addr(0x4433221105000000) > [ 2.768394] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 6) > [ 2.769136] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x000a), sas_addr(0x4433221106000000) > [ 2.769510] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 5) > [ 2.769888] mpt2sas_cm1: _scsih_determine_boot_device: current_boot_device(0x4433221106000000) > [ 2.770641] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x000c), sas_addr(0x4433221107000000) > [ 2.771025] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 4) > [ 2.771405] mpt2sas_cm1: discovery event: (stop) > > [ 2.771788] mpt2sas_cm1: discovery event: (start) > > [ 2.772172] mpt2sas_cm1: discovery event: (stop) > > [ 2.772554] mpt2sas_cm1: discovery event: (start) > > [ 2.772942] mpt2sas_cm1: discovery event: (stop) > > [ 2.773326] mpt2sas_cm1: discovery event: (start) > > [ 2.773709] mpt2sas_cm1: discovery event: (stop) > > [ 2.774090] mpt2sas_cm1: discovery event: (start) > > [ 2.774474] mpt2sas_cm1: discovery event: (stop) > > [ 2.774855] mpt2sas_cm1: discovery event: (start) > > [ 2.775237] mpt2sas_cm1: discovery event: (stop) > > [ 2.775619] mpt2sas_cm1: port enable: complete from worker thread > [ 2.780192] mpt2sas_cm1: port enable: SUCCESS > [ 2.782404] scsi 1:0:0:0: Direct-Access ATA Hitachi HDP72505 A5BA PQ: 0 ANSI: 6 > [ 2.782651] scsi 1:0:0:0: SATA: handle(0x000a), sas_addr(0x4433221106000000), phy(6), device_name(0x5000cca34dc05584) > [ 2.783039] scsi 1:0:0:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(5) > [ 2.783390] scsi 1:0:0:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) > [ 2.803032] scsi 1:0:1:0: Direct-Access ATA ST8000AS0002-1NA AR15 PQ: 0 ANSI: 6 > [ 2.803272] scsi 1:0:1:0: SATA: handle(0x000e), sas_addr(0x4433221102000000), phy(2), device_name(0x5000c500908f1d05) > [ 2.803660] scsi 1:0:1:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(1) > [ 2.803981] scsi 1:0:1:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) > [ 2.821712] scsi 1:0:2:0: Direct-Access ATA ST3000DM001-1CH1 CC43 PQ: 0 ANSI: 6 > [ 2.821963] scsi 1:0:2:0: SATA: handle(0x000b), sas_addr(0x4433221103000000), phy(3), device_name(0x5000c5004dfd2a8a) > [ 2.822352] scsi 1:0:2:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(0) > [ 2.822694] scsi 1:0:2:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) > [ 2.844233] scsi 1:0:3:0: Direct-Access ATA ST3500320NS SN16 PQ: 0 ANSI: 6 > [ 2.844483] scsi 1:0:3:0: SATA: handle(0x000d), sas_addr(0x4433221104000000), phy(4), device_name(0x5000c50009dca65b) > [ 2.844870] scsi 1:0:3:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(7) > [ 2.845216] scsi 1:0:3:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) > [ 2.868963] scsi 1:0:4:0: Direct-Access ATA SAMSUNG HD401LJ 0-15 PQ: 0 ANSI: 6 > [ 2.870994] scsi 1:0:4:0: SATA: handle(0x0009), sas_addr(0x4433221105000000), phy(5), device_name(0x695d550daf678093) > [ 2.871382] scsi 1:0:4:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(6) > [ 2.871728] scsi 1:0:4:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) > [ 2.894004] scsi 1:0:5:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 > [ 2.894257] scsi 1:0:5:0: SATA: handle(0x000c), sas_addr(0x4433221107000000), phy(7), device_name(0x5000c5000266bb02) > [ 2.894646] scsi 1:0:5:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(4) > [ 2.894972] scsi 1:0:5:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) I don't see a clear pattern yet, but I suspect warm rebooting >=4.2 after having run 4.1.x leads to sucessful driver inits. But I also remember having had cold boots, with kernels >=4.2 that worked fine (obviously not all of the time). <=4.1.20 kernels on the other hand boot fine every single time. Interestingly the igb driver (ethernet) seems to be acting up at least with 4.5.0 on exactly the same boots when mpt2sas init fails. I don't know whether this could be connected or not (I just became aware of this coincidence). --- Matthias Am 21.03.2016 um 05:53 schrieb Sreekanth Reddy: > Hi Matthias, > > Can you please share us the driver logs with driver logging_level set > to 0x3f8. So that we can get more info from this log. > > Thanks, > Sreekanth > > On Mon, Mar 21, 2016 at 1:44 AM, Matthias Prager > <linux@matthiasprager.de> wrote: >> Hello, >> >> I don't know what's the correct procedure, whether I should file a bug or first report this issue on the kernel mailing-list. So please feel free to tell me to open a ticket in the bugtracker (bugzilla.kernel.org?). >> >> But first let me present the issue I encounter: >> >> Kernels >= 4.2 (4.2.1 was the first on I tried, but also 4.3, 4.4 and 4.5) fail to load the mpt2sas driver on most (but not all) boots. Kernels <= 4.1.x work fine every single time (4.1.19 was the latest I tried, also 3.18.29). >> >> Here is the dmesg output for a failed driver init with Kernel 4.5.0: >>> [ 2.068313] mpt3sas version 09.102.00.00 loaded >>> [ 2.069412] mpt2sas_cm0: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3074748 kB) >>> [ 2.125260] mpt2sas_cm0: MSI-X vectors supported: 1, no of cores: 4, max_msix_vectors: -1 >>> [ 2.125996] mpt2sas0-msix0: PCI-MSI-X enabled: IRQ 58 >>> [ 2.126199] mpt2sas_cm0: iomem(0x00000000fd4fc000), mapped(0xffffc900000d0000), size(16384) >>> [ 2.126430] mpt2sas_cm0: ioport(0x0000000000004000), size(256) >>> [ 2.216371] mpt2sas_cm0: Allocated physical memory: size(4964 kB) >>> [ 2.216600] mpt2sas_cm0: Current Controller Queue Depth(3307),Max Controller Queue Depth(3432) >>> [ 2.217004] mpt2sas_cm0: Scatter Gather Elements per IO(128) >>> [ 5.086959] floppy0: no floppy controllers found >>> [ 32.256720] mpt2sas_cm0: _base_event_notification: timeout >>> [ 32.256940] mf: >>> >>> [ 32.257106] 07000000 >>> [ 32.257302] 00000000 >>> [ 32.257337] 00000000 >>> [ 32.257533] 00000000 >>> [ 32.257568] 00000000 >>> [ 32.257764] 0f2f7fff >>> [ 32.257800] ffffff7c >>> [ 32.257995] ffffffff >>> [ 32.258031] >>> >>> [ 32.258352] ffffffff >>> [ 32.258387] 00000000 >>> [ 32.258582] 00000000 >>> >>> [ 32.258950] mpt2sas_cm0: sending message unit reset !! >>> [ 32.260688] mpt2sas_cm0: message unit reset: SUCCESS >>> [ 32.325956] mpt2sas_cm0: failure at drivers/scsi/mpt3sas/mpt3sas_scsih.c:8592/_scsih_probe()! >> >> For comparison here is a dmesg output for a successful boot on Kernel 4.1.15: >>> [ 2.035568] mpt2sas version 20.100.00.00 loaded >>> [ 2.037243] mpt2sas0: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (2046352 kB) >>> [ 2.755374] mpt2sas0: MSI-X vectors supported: 1, no of cores: 3, max_msix_vectors: 8 >>> [ 2.756377] mpt2sas0-msix0: PCI-MSI-X enabled: IRQ 58 >>> [ 2.756708] mpt2sas0: iomem(0x00000000fd5fc000), mapped(0xffffc900000d0000), size(16384) >>> [ 2.757083] mpt2sas0: ioport(0x0000000000004000), size(256) >>> [ 3.842944] mpt2sas0: Allocated physical memory: size(4964 kB) >>> [ 3.843303] mpt2sas0: Current Controller Queue Depth(3307), Max Controller Queue Depth(3432) >>> [ 3.843717] mpt2sas0: Scatter Gather Elements per IO(128) >>> [ 4.415980] mpt2sas0: LSISAS2008: FWVersion(20.00.04.00), ChipRevision(0x03), BiosVersion(07.39.00.00) >>> [ 4.416618] mpt2sas0: Protocol=(Initiator,Target), Capabilities=(TLR,EEDP,Snapshot Buffer,Diag Trace Buffer,Task Set Full,NCQ) >>> [ 4.417846] scsi host0: Fusion MPT SAS Host >>> [ 4.436865] mpt2sas0: sending port enable !! >>> [ 4.440460] mpt2sas0: host_add: handle(0x0001), sas_addr(0xxxxxxxxxxxxxxxxx), phys(8) >>> >>> ... >>> [ 4.444045] scsi 0:0:0:0: Direct-Access ATA Hitachi HDS5C302 A800 PQ: 0 ANSI: 6 >>> [ 4.444338] scsi 0:0:0:0: SATA: handle(0x0009), sas_addr(0xxxxxxxxxxxxxxxxx), phy(1), device_name(0xxxxxxxxxxxxxxxxx) >>> [ 4.444823] scsi 0:0:0:0: SATA: enclosure_logical_id(0xxxxxxxxxxxxxxxxx), slot(2) >>> [ 4.445197] scsi 0:0:0:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>> ... (n times for n drives) >>> >>> [ 4.515443] mpt2sas0: port enable: SUCCESS >> >> >> The Controller(s) are all Avego/LSI 9211-8i running the latest version of IT firmware (v20.00.04.00). These are passed through to a gentoo-linux VM on an ESXi 5.1 host (latest patchlevel). I have two of these systems (one production one testing) with nearly identical hardware (Supermicro X8DTi-F boards with 2x Intel Westmere CPUs). I also have an older set of systems running the same software config (Intel S3200SHLC boards with single Core2Quad) which exhibit the same buggy behavior. >> >> The 'uname -a' line on the current testing system looks like this: >>> Linux pserver2 4.1.19-gentoo #4 SMP Thu Mar 17 16:02:48 CET 2016 x86_64 Intel(R) Xeon(R) CPU E5506 @ 2.13GHz GenuineIntel GNU/Linux >> p >> >> There seem to be other people with similar issues: >> <https://bbs.archlinux.org/viewtopic.php?id=209495> >> >> Any thoughts? >> >> --- >> Matthias ^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [BUG] mpt2sas: driver init fails on kernel >=4.2 for 9211-8i IT 2016-03-21 9:18 ` Matthias Prager @ 2016-03-21 13:59 ` Sreekanth Reddy 2016-03-21 15:52 ` Matthias Prager 0 siblings, 1 reply; 13+ messages in thread From: Sreekanth Reddy @ 2016-03-21 13:59 UTC (permalink / raw) To: Matthias Prager; +Cc: linux-scsi Hi Matthias, Thanks for providing the logs. In these logs, I am not observing any such a prints which should be suspected for this issue. Can you please try once by setting mpt3sas driver's "msix_disable" module parameter to one. Also, can you please elaborate below statement for me, I am not able understand this statement "I managed to boot the same 4.5.0 kernel successfully after warm rebooting from 4.1.20" Thanks, Sreekanth On Mon, Mar 21, 2016 at 2:48 PM, Matthias Prager <linux@matthiasprager.de> wrote: > Hi Sreekanth, > > thank you for replying so quickly. Here are the logs you requested > (kernel 4.5.0): > >> [ 2.083177] mpt3sas version 09.102.00.00 loaded >> [ 2.083757] mpt2sas_cm0: mpt3sas_base_attach >> [ 2.083956] mpt2sas_cm0: mpt3sas_base_map_resources >> [ 2.084708] mpt2sas_cm0: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3074748 kB) >> [ 2.084964] mpt2sas_cm0: _base_get_ioc_facts >> [ 2.085154] mpt2sas_cm0: _base_wait_for_iocstate >> [ 2.140893] offset:data >> [ 2.141082] [0x00]:03100200 >> [ 2.141257] [0x04]:00002300 >> [ 2.141432] [0x08]:00000000 >> [ 2.141606] [0x0c]:00000000 >> [ 2.141780] [0x10]:00000000 >> [ 2.141955] [0x14]:00010480 >> [ 2.142129] [0x18]:22130d68 >> [ 2.142303] [0x1c]:0001285c >> [ 2.142477] [0x20]:14000400 >> [ 2.142651] [0x24]:00000020 >> [ 2.142825] [0x28]:0100000f >> [ 2.143000] [0x2c]:000c000b >> [ 2.143174] [0x30]:003c0003 >> [ 2.143349] [0x34]:0020ffe0 >> [ 2.143544] [0x38]:00800122 >> [ 2.143719] [0x3c]:00000009 >> [ 2.143895] mpt2sas_cm0: hba queue depth(3432), max chains per io(128) >> [ 2.144106] mpt2sas_cm0: request frame size(128), reply frame size(128) >> [ 2.144397] mpt2sas_cm0: msix is supported, vector_count(1) >> [ 2.144600] mpt2sas_cm0: MSI-X vectors supported: 1, no of cores: 4, max_msix_vectors: -1 >> [ 2.145161] mpt2sas0-msix0: PCI-MSI-X enabled: IRQ 58 >> [ 2.145361] mpt2sas_cm0: iomem(0x00000000fd4fc000), mapped(0xffffc900000d0000), size(16384) >> [ 2.145591] mpt2sas_cm0: ioport(0x0000000000004000), size(256) >> [ 2.146206] mpt2sas_cm0: _base_get_ioc_facts >> [ 2.146397] mpt2sas_cm0: _base_wait_for_iocstate >> [ 2.202087] offset:data >> [ 2.202281] [0x00]:03100200 >> [ 2.202456] [0x04]:00002300 >> [ 2.202631] [0x08]:00000000 >> [ 2.202805] [0x0c]:00000000 >> [ 2.202980] [0x10]:00000000 >> [ 2.203154] [0x14]:00010480 >> [ 2.203328] [0x18]:22130d68 >> [ 2.203521] [0x1c]:0001285c >> [ 2.203695] [0x20]:14000400 >> [ 2.203870] [0x24]:00000020 >> [ 2.204044] [0x28]:0100000f >> [ 2.204219] [0x2c]:000c000b >> [ 2.204394] [0x30]:003c0003 >> [ 2.204571] [0x34]:0020ffe0 >> [ 2.204746] [0x38]:00800122 >> [ 2.204926] [0x3c]:00000009 >> [ 2.205102] mpt2sas_cm0: hba queue depth(3432), max chains per io(128) >> [ 2.205314] mpt2sas_cm0: request frame size(128), reply frame size(128) >> [ 2.205528] mpt2sas_cm0: _base_make_ioc_ready >> [ 2.205719] mpt2sas_cm0: _base_get_port_facts >> [ 2.234205] offset:data >> [ 2.234397] [0x00]:05070000 >> [ 2.234573] [0x04]:00000000 >> [ 2.234748] [0x08]:00000000 >> [ 2.234928] [0x0c]:00000000 >> [ 2.235103] [0x10]:00000000 >> [ 2.235278] [0x14]:00003000 >> [ 2.235453] [0x18]:00000078 >> [ 2.235629] mpt2sas_cm0: _base_allocate_memory_pools >> [ 2.235826] mpt2sas_cm0: scatter gather: sge_in_main_msg(3), sge_per_chain(15), sge_per_io(128), chains_per_io(9) >> [ 2.236227] mpt2sas_cm0: reply post free pool (0xffff8800bb380000): depth(6944),element_size(8), pool_size(54 kB) >> [ 2.236611] mpt2sas_cm0: reply_post_free_dma = (0xbb380000) >> [ 2.236813] mpt2sas_cm0: scsi host: can_queue depth (3307) >> [ 2.237086] mpt2sas_cm0: request pool(0xffff8800ba880000): depth(3432), frame_size(128), pool_size(429 kB) >> [ 2.238580] mpt2sas_cm0: request pool: dma(0xba880000) >> [ 2.238781] mpt2sas_cm0: scsiio(0xffff8800ba880000): depth(3307) >> [ 2.243644] mpt2sas_cm0: chain pool depth(29763), frame_size(128), pool_size(3720 kB) >> [ 2.243887] mpt2sas_cm0: hi_priority(0xffff8800ba8e7600): depth(60), start smid(3308) >> [ 2.244113] mpt2sas_cm0: internal(0xffff8800ba8e9400): depth(65), start smid(3368) >> [ 2.244390] mpt2sas_cm0: sense pool(0xffff8800ba480000): depth(3307), element_size(96), pool_size(310 kB) >> [ 2.244774] mpt2sas_cm0: sense_dma(0xba480000) >> [ 2.245038] mpt2sas_cm0: reply pool(0xffff8800ba500000): depth(3496), frame_size(128), pool_size(437 kB) >> [ 2.245413] mpt2sas_cm0: reply_dma(0xba500000) >> [ 2.245608] mpt2sas_cm0: reply_free pool(0xffff8800ba430000): depth(3496), element_size(4), pool_size(13 kB) >> [ 2.245985] mpt2sas_cm0: reply_free_dma (0xba430000) >> [ 2.246181] mpt2sas_cm0: config page(0xffff8800ba429000): size(512) >> [ 2.246389] mpt2sas_cm0: config_page_dma(0xba429000) >> [ 2.246584] mpt2sas_cm0: Allocated physical memory: size(4964 kB) >> [ 2.246791] mpt2sas_cm0: Current Controller Queue Depth(3307),Max Controller Queue Depth(3432) >> [ 2.247155] mpt2sas_cm0: Scatter Gather Elements per IO(128) >> [ 2.247361] mpt2sas_cm0: _base_make_ioc_operational >> [ 2.247962] mpt2sas_cm0: _base_send_ioc_init >> [ 2.248154] offset:data >> [ 2.248325] [0x00]:02000004 >> [ 2.248499] [0x04]:00000000 >> [ 2.248673] [0x08]:00000000 >> [ 2.248848] [0x0c]:23000200 >> [ 2.249023] [0x10]:00000000 >> [ 2.249197] [0x14]:00000000 >> [ 2.249372] [0x18]:00200000 >> [ 2.249546] [0x1c]:0da81b20 >> [ 2.249720] [0x20]:00000000 >> [ 2.249894] [0x24]:00000000 >> [ 2.250068] [0x28]:ba880000 >> [ 2.250242] [0x2c]:00000000 >> [ 2.250416] [0x30]:bb380000 >> [ 2.250589] [0x34]:00000000 >> [ 2.250768] [0x38]:ba430000 >> [ 2.250941] [0x3c]:00000000 >> [ 2.251115] [0x40]:983eb686 >> [ 2.251288] [0x44]:00000153 >> [ 2.296610] offset:data >> [ 2.296795] [0x00]:02050004 >> [ 2.296969] [0x04]:00000000 >> [ 2.297143] [0x08]:00000000 >> [ 2.297318] [0x0c]:00000000 >> [ 2.297493] [0x10]:00000000 >> [ 2.297668] mpt2sas_cm0: _base_event_notification >> [ 5.093707] floppy0: no floppy controllers found >> [ 32.293619] mpt2sas_cm0: _base_event_notification: timeout >> [ 32.293909] mf: >> >> [ 32.294132] 07000000 >> [ 32.294397] 00000000 >> [ 32.294445] 00000000 >> [ 32.294719] 00000000 >> [ 32.294767] 00000000 >> [ 32.295031] 0f2f7fff >> [ 32.295078] ffffff7c >> [ 32.295342] ffffffff >> [ 32.295389] >> >> [ 32.295823] ffffffff >> [ 32.295871] 00000000 >> [ 32.296134] 00000000 >> >> [ 32.296615] mpt2sas_cm0: mpt3sas_base_free_resources >> [ 32.296880] mpt2sas_cm0: _base_make_ioc_ready >> [ 32.297135] mpt2sas_cm0: sending message unit reset !! >> [ 32.298941] mpt2sas_cm0: message unit reset: SUCCESS >> [ 32.299212] mpt2sas_cm0: mpt3sas_base_unmap_resources >> [ 32.300381] mpt2sas_cm0: _base_release_memory_pools >> [ 32.300654] mpt2sas_cm0: request_pool(0xffff8800ba880000): free >> [ 32.300934] mpt2sas_cm0: sense_pool(0xffff8800ba480000): free >> [ 32.301211] mpt2sas_cm0: reply_pool(0xffff8800ba500000): free >> [ 32.301485] mpt2sas_cm0: reply_free_pool(0xffff8800ba430000): free >> [ 32.301774] mpt2sas_cm0: reply_post_free_pool(0xffff8800bb380000): free >> [ 32.302061] mpt2sas_cm0: config_page(0xffff8800ba429000): free >> [ 32.371097] mpt2sas_cm0: failure at drivers/scsi/mpt3sas/mpt3sas_scsih.c:8592/_scsih_probe()! >> [ 32.371958] mpt2sas_cm1: mpt3sas_base_attach >> [ 32.372154] mpt2sas_cm1: mpt3sas_base_map_resources >> [ 32.372950] mpt2sas_cm1: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3074748 kB) >> [ 32.373201] mpt2sas_cm1: _base_get_ioc_facts >> [ 32.375261] mpt2sas_cm1: _base_wait_for_iocstate >> [ 32.432012] offset:data >> [ 32.432262] [0x00]:03100200 >> [ 32.432499] [0x04]:00002300 >> [ 32.432735] [0x08]:00000000 >> [ 32.432971] [0x0c]:00000000 >> [ 32.433206] [0x10]:00000000 >> [ 32.433443] [0x14]:00010480 >> [ 32.433701] [0x18]:22130d68 >> [ 32.433937] [0x1c]:0001285c >> [ 32.435434] [0x20]:14000400 >> [ 32.435674] [0x24]:00000020 >> [ 32.435909] [0x28]:0100000f >> [ 32.436144] [0x2c]:000c000b >> [ 32.436379] [0x30]:003c0003 >> [ 32.436615] [0x34]:0020ffe0 >> [ 32.436850] [0x38]:00800122 >> [ 32.437085] [0x3c]:00000009 >> [ 32.437322] mpt2sas_cm1: hba queue depth(3432), max chains per io(128) >> [ 32.437607] mpt2sas_cm1: request frame size(128), reply frame size(128) >> [ 32.438014] mpt2sas_cm1: msix is supported, vector_count(1) >> [ 32.438288] mpt2sas_cm1: MSI-X vectors supported: 1, no of cores: 4, max_msix_vectors: 8 >> [ 32.439101] mpt2sas1-msix0: PCI-MSI-X enabled: IRQ 58 >> [ 32.439373] mpt2sas_cm1: iomem(0x00000000fd1fc000), mapped(0xffffc900000d8000), size(16384) >> [ 32.439682] mpt2sas_cm1: ioport(0x0000000000007000), size(256) >> [ 32.440504] mpt2sas_cm1: _base_get_ioc_facts >> [ 32.440765] mpt2sas_cm1: _base_wait_for_iocstate >> [ 32.499305] offset:data >> [ 32.499557] [0x00]:03100200 >> [ 32.499794] [0x04]:00002300 >> [ 32.500031] [0x08]:00000000 >> [ 32.500267] [0x0c]:00000000 >> [ 32.500504] [0x10]:00000000 >> [ 32.500740] [0x14]:00010480 >> [ 32.500974] [0x18]:22130d68 >> [ 32.501209] [0x1c]:0001285c >> [ 32.501444] [0x20]:14000400 >> [ 32.501687] [0x24]:00000020 >> [ 32.501922] [0x28]:0100000f >> [ 32.502157] [0x2c]:000c000b >> [ 32.502391] [0x30]:003c0003 >> [ 32.502626] [0x34]:0020ffe0 >> [ 32.502862] [0x38]:00800122 >> [ 32.503098] [0x3c]:00000009 >> [ 32.503336] mpt2sas_cm1: hba queue depth(3432), max chains per io(128) >> [ 32.503644] mpt2sas_cm1: request frame size(128), reply frame size(128) >> [ 32.503933] mpt2sas_cm1: _base_make_ioc_ready >> [ 32.504191] mpt2sas_cm1: _base_get_port_facts >> [ 32.534282] offset:data >> [ 32.534537] [0x00]:05070000 >> [ 32.534782] [0x04]:00000000 >> [ 32.535058] [0x08]:00000000 >> [ 32.536473] [0x0c]:00000000 >> [ 32.536710] [0x10]:00000000 >> [ 32.536946] [0x14]:00003000 >> [ 32.537183] [0x18]:00000078 >> [ 32.537420] mpt2sas_cm1: _base_allocate_memory_pools >> [ 32.537686] mpt2sas_cm1: scatter gather: sge_in_main_msg(3), sge_per_chain(15), sge_per_io(128), chains_per_io(9) >> [ 32.538232] mpt2sas_cm1: reply post free pool (0xffff8800bb3d0000): depth(6944),element_size(8), pool_size(54 kB) >> [ 32.538758] mpt2sas_cm1: reply_post_free_dma = (0xbb3d0000) >> [ 32.539030] mpt2sas_cm1: scsi host: can_queue depth (3307) >> [ 32.539378] mpt2sas_cm1: request pool(0xffff8800ba480000): depth(3432), frame_size(128), pool_size(429 kB) >> [ 32.539882] mpt2sas_cm1: request pool: dma(0xba480000) >> [ 32.540149] mpt2sas_cm1: scsiio(0xffff8800ba480000): depth(3307) >> [ 32.545893] mpt2sas_cm1: chain pool depth(29763), frame_size(128), pool_size(3720 kB) >> [ 32.546137] mpt2sas_cm1: hi_priority(0xffff8800ba4e7600): depth(60), start smid(3308) >> [ 32.546365] mpt2sas_cm1: internal(0xffff8800ba4e9400): depth(65), start smid(3368) >> [ 32.546651] mpt2sas_cm1: sense pool(0xffff8800ba880000): depth(3307), element_size(96), pool_size(310 kB) >> [ 32.547030] mpt2sas_cm1: sense_dma(0xba880000) >> [ 32.547537] mpt2sas_cm1: reply pool(0xffff880000100000): depth(3496), frame_size(128), pool_size(437 kB) >> [ 32.547921] mpt2sas_cm1: reply_dma(0x100000) >> [ 32.548117] mpt2sas_cm1: reply_free pool(0xffff8800ba964000): depth(3496), element_size(4), pool_size(13 kB) >> [ 32.548500] mpt2sas_cm1: reply_free_dma (0xba964000) >> [ 32.548698] mpt2sas_cm1: config page(0xffff8800ba960000): size(512) >> [ 32.548908] mpt2sas_cm1: config_page_dma(0xba960000) >> [ 32.549105] mpt2sas_cm1: Allocated physical memory: size(4964 kB) >> [ 32.549314] mpt2sas_cm1: Current Controller Queue Depth(3307),Max Controller Queue Depth(3432) >> [ 32.550950] mpt2sas_cm1: Scatter Gather Elements per IO(128) >> [ 32.551160] mpt2sas_cm1: _base_make_ioc_operational >> [ 32.551855] mpt2sas_cm1: _base_send_ioc_init >> [ 32.552051] offset:data >> [ 32.552224] [0x00]:02000004 >> [ 32.552400] [0x04]:00000000 >> [ 32.552576] [0x08]:00000000 >> [ 32.552761] [0x0c]:23000200 >> [ 32.552937] [0x10]:00000000 >> [ 32.553114] [0x14]:00000000 >> [ 32.553291] [0x18]:00200000 >> [ 32.553468] [0x1c]:0da81b20 >> [ 32.553685] [0x20]:00000000 >> [ 32.553862] [0x24]:00000000 >> [ 32.554038] [0x28]:ba480000 >> [ 32.554215] [0x2c]:00000000 >> [ 32.554393] [0x30]:bb3d0000 >> [ 32.554569] [0x34]:00000000 >> [ 32.554752] [0x38]:ba964000 >> [ 32.554929] [0x3c]:00000000 >> [ 32.555106] [0x40]:983f2ce6 >> [ 32.555283] [0x44]:00000153 >> [ 32.601516] offset:data >> [ 32.601768] [0x00]:02050004 >> [ 32.602003] [0x04]:00000000 >> [ 32.602239] [0x08]:00000000 >> [ 32.602474] [0x0c]:00000000 >> [ 32.602709] [0x10]:00000000 >> [ 32.602945] mpt2sas_cm1: _base_event_notification >> [ 62.593604] mpt2sas_cm1: _base_event_notification: timeout >> [ 62.593906] mf: >> >> [ 62.594127] 07000000 >> [ 62.594390] 00000000 >> [ 62.594438] 00000000 >> [ 62.594709] 00000000 >> [ 62.594757] 00000000 >> [ 62.595019] 0f2f7fff >> [ 62.595067] ffffff7c >> [ 62.595330] ffffffff >> [ 62.595377] >> >> [ 62.595808] ffffffff >> [ 62.595855] 00000000 >> [ 62.596117] 00000000 >> >> [ 62.596601] mpt2sas_cm1: mpt3sas_base_free_resources >> [ 62.596871] mpt2sas_cm1: _base_make_ioc_ready >> [ 62.597125] mpt2sas_cm1: sending message unit reset !! >> [ 62.599013] mpt2sas_cm1: message unit reset: SUCCESS >> [ 62.599283] mpt2sas_cm1: mpt3sas_base_unmap_resources >> [ 62.600443] mpt2sas_cm1: _base_release_memory_pools >> [ 62.600721] mpt2sas_cm1: request_pool(0xffff8800ba480000): free >> [ 62.601002] mpt2sas_cm1: sense_pool(0xffff8800ba880000): free >> [ 62.601280] mpt2sas_cm1: reply_pool(0xffff880000100000): free >> [ 62.601560] mpt2sas_cm1: reply_free_pool(0xffff8800ba964000): free >> [ 62.601845] mpt2sas_cm1: reply_post_free_pool(0xffff8800bb3d0000): free >> [ 62.602133] mpt2sas_cm1: config_page(0xffff8800ba960000): free >> [ 62.673591] mpt2sas_cm1: failure at drivers/scsi/mpt3sas/mpt3sas_scsih.c:8592/_scsih_probe()! > > These are for two controllers, I don't know whether the output from the > second is helpful at all - I added it anyway. > > > I managed to boot the same 4.5.0 kernel successfully after warm > rebooting from 4.1.20. That gave me this dmesg output (for comparison): > >> [ 2.057685] mpt3sas version 09.102.00.00 loaded >> [ 2.058371] mpt2sas_cm0: mpt3sas_base_attach >> [ 2.058632] mpt2sas_cm0: mpt3sas_base_map_resources >> [ 2.059583] mpt2sas_cm0: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3074748 kB) >> [ 2.059911] mpt2sas_cm0: _base_get_ioc_facts >> [ 2.060166] mpt2sas_cm0: _base_wait_for_iocstate >> [ 2.116337] offset:data >> [ 2.116576] [0x00]:03100200 >> [ 2.116817] [0x04]:00002300 >> [ 2.117051] [0x08]:00000000 >> [ 2.117285] [0x0c]:00000000 >> [ 2.117518] [0x10]:00000000 >> [ 2.117752] [0x14]:00010480 >> [ 2.117986] [0x18]:22130d68 >> [ 2.118220] [0x1c]:0001285c >> [ 2.119624] [0x20]:14000400 >> [ 2.119858] [0x24]:00000020 >> [ 2.120093] [0x28]:0100000f >> [ 2.120351] [0x2c]:000c000b >> [ 2.120586] [0x30]:003c0003 >> [ 2.120820] [0x34]:0020ffe0 >> [ 2.121055] [0x38]:00800122 >> [ 2.121288] [0x3c]:00000009 >> [ 2.121524] mpt2sas_cm0: hba queue depth(3432), max chains per io(128) >> [ 2.121808] mpt2sas_cm0: request frame size(128), reply frame size(128) >> [ 2.122195] mpt2sas_cm0: msix is supported, vector_count(1) >> [ 2.122468] mpt2sas_cm0: MSI-X vectors supported: 1, no of cores: 4, max_msix_vectors: -1 >> [ 2.123239] mpt2sas0-msix0: PCI-MSI-X enabled: IRQ 58 >> [ 2.123507] mpt2sas_cm0: iomem(0x00000000fd4fc000), mapped(0xffffc900000d0000), size(16384) >> [ 2.123816] mpt2sas_cm0: ioport(0x0000000000004000), size(256) >> [ 2.124623] mpt2sas_cm0: _base_get_ioc_facts >> [ 2.124878] mpt2sas_cm0: _base_wait_for_iocstate >> [ 2.180907] offset:data >> [ 2.181145] [0x00]:03100200 >> [ 2.181379] [0x04]:00002300 >> [ 2.181613] [0x08]:00000000 >> [ 2.181847] [0x0c]:00000000 >> [ 2.182081] [0x10]:00000000 >> [ 2.182315] [0x14]:00010480 >> [ 2.182547] [0x18]:22130d68 >> [ 2.182781] [0x1c]:0001285c >> [ 2.183014] [0x20]:14000400 >> [ 2.183248] [0x24]:00000020 >> [ 2.183481] [0x28]:0100000f >> [ 2.183720] [0x2c]:000c000b >> [ 2.183954] [0x30]:003c0003 >> [ 2.184190] [0x34]:0020ffe0 >> [ 2.184424] [0x38]:00800122 >> [ 2.184658] [0x3c]:00000009 >> [ 2.184893] mpt2sas_cm0: hba queue depth(3432), max chains per io(128) >> [ 2.185177] mpt2sas_cm0: request frame size(128), reply frame size(128) >> [ 2.185462] mpt2sas_cm0: _base_make_ioc_ready >> [ 2.185717] mpt2sas_cm0: _base_get_port_facts >> [ 2.214057] offset:data >> [ 2.214295] [0x00]:05070000 >> [ 2.214529] [0x04]:00000000 >> [ 2.214762] [0x08]:00000000 >> [ 2.214997] [0x0c]:00000000 >> [ 2.215230] [0x10]:00000000 >> [ 2.215464] [0x14]:00003000 >> [ 2.215697] [0x18]:00000078 >> [ 2.215931] mpt2sas_cm0: _base_allocate_memory_pools >> [ 2.216194] mpt2sas_cm0: scatter gather: sge_in_main_msg(3), sge_per_chain(15), sge_per_io(128), chains_per_io(9) >> [ 2.216734] mpt2sas_cm0: reply post free pool (0xffff8800bafc0000): depth(6944),element_size(8), pool_size(54 kB) >> [ 2.217244] mpt2sas_cm0: reply_post_free_dma = (0xbafc0000) >> [ 2.217514] mpt2sas_cm0: scsi host: can_queue depth (3307) >> [ 2.217866] mpt2sas_cm0: request pool(0xffff8800ba800000): depth(3432), frame_size(128), pool_size(429 kB) >> [ 2.218369] mpt2sas_cm0: request pool: dma(0xba800000) >> [ 2.218637] mpt2sas_cm0: scsiio(0xffff8800ba800000): depth(3307) >> [ 2.224773] mpt2sas_cm0: chain pool depth(29763), frame_size(128), pool_size(3720 kB) >> [ 2.225092] mpt2sas_cm0: hi_priority(0xffff8800ba867600): depth(60), start smid(3308) >> [ 2.225395] mpt2sas_cm0: internal(0xffff8800ba869400): depth(65), start smid(3368) >> [ 2.225958] mpt2sas_cm0: sense pool(0xffff8800ba480000): depth(3307), element_size(96), pool_size(310 kB) >> [ 2.226457] mpt2sas_cm0: sense_dma(0xba480000) >> [ 2.227039] mpt2sas_cm0: reply pool(0xffff8800ba500000): depth(3496), frame_size(128), pool_size(437 kB) >> [ 2.227413] mpt2sas_cm0: reply_dma(0xba500000) >> [ 2.227616] mpt2sas_cm0: reply_free pool(0xffff8800ba450000): depth(3496), element_size(4), pool_size(13 kB) >> [ 2.227992] mpt2sas_cm0: reply_free_dma (0xba450000) >> [ 2.228192] mpt2sas_cm0: config page(0xffff8800ba43b000): size(512) >> [ 2.228402] mpt2sas_cm0: config_page_dma(0xba43b000) >> [ 2.228598] mpt2sas_cm0: Allocated physical memory: size(4964 kB) >> [ 2.228806] mpt2sas_cm0: Current Controller Queue Depth(3307),Max Controller Queue Depth(3432) >> [ 2.229171] mpt2sas_cm0: Scatter Gather Elements per IO(128) >> [ 2.229378] mpt2sas_cm0: _base_make_ioc_operational >> [ 2.229959] mpt2sas_cm0: _base_send_ioc_init >> [ 2.230151] offset:data >> [ 2.230323] [0x00]:02000004 >> [ 2.230499] [0x04]:00000000 >> [ 2.230675] [0x08]:00000000 >> [ 2.230851] [0x0c]:23000200 >> [ 2.231026] [0x10]:00000000 >> [ 2.231201] [0x14]:00000000 >> [ 2.231376] [0x18]:00200000 >> [ 2.231551] [0x1c]:0da81b20 >> [ 2.231726] [0x20]:00000000 >> [ 2.231900] [0x24]:00000000 >> [ 2.232075] [0x28]:ba800000 >> [ 2.232250] [0x2c]:00000000 >> [ 2.232423] [0x30]:bafc0000 >> [ 2.232597] [0x34]:00000000 >> [ 2.232775] [0x38]:ba450000 >> [ 2.232950] [0x3c]:00000000 >> [ 2.233125] [0x40]:98596e4f >> [ 2.233299] [0x44]:00000153 >> [ 2.278752] offset:data >> [ 2.278988] [0x00]:02050004 >> [ 2.279220] [0x04]:00000000 >> [ 2.279453] [0x08]:00000000 >> [ 2.279685] [0x0c]:00000000 >> [ 2.279918] [0x10]:00000000 >> [ 2.280151] mpt2sas_cm0: _base_event_notification >> [ 2.280537] mpt2sas_cm0: _base_event_notification: complete >> [ 2.281694] mpt2sas_cm0: LSISAS2008: FWVersion(20.00.04.00), ChipRevision(0x03), BiosVersion(07.39.00.00) >> [ 2.282196] mpt2sas_cm0: Protocol=( >> [ 2.282261] Initiator >> [ 2.282522] ,Target >> [ 2.282567] ), >> [ 2.282824] Capabilities=( >> [ 2.282877] TLR >> [ 2.283132] ,EEDP >> [ 2.283175] ,Snapshot Buffer >> [ 2.283444] ,Diag Trace Buffer >> [ 2.283502] ,Task Set Full >> [ 2.283774] ,NCQ >> [ 2.283816] ) >> [ 2.284350] scsi host0: Fusion MPT SAS Host >> [ 2.299028] mpt2sas_cm0: sending port enable !! >> [ 2.299540] mpt2sas_cm0: Discovery: (start) >> >> [ 2.299972] mpt2sas_cm0: SAS Enclosure Device Status Change >> [ 2.299984] mpt2sas_cm0: discovery event: (start) >> >> [ 2.300554] mpt2sas_cm0: SAS Topology Change List >> [ 2.300759] mpt2sas_cm0: Discovery: (stop) >> >> [ 2.301146] mpt2sas_cm0: Discovery: (start) >> >> [ 2.301535] mpt2sas_cm0: Discovery: (stop) >> >> [ 2.301927] mpt2sas_cm0: Discovery: (start) >> >> [ 2.302316] mpt2sas_cm0: Discovery: (stop) >> >> [ 2.302707] mpt2sas_cm0: Discovery: (start) >> >> [ 2.304908] mpt2sas_cm0: Discovery: (stop) >> >> [ 2.305297] mpt2sas_cm0: Discovery: (start) >> >> [ 2.306776] mpt2sas_cm0: Discovery: (stop) >> >> [ 2.307166] mpt2sas_cm0: Discovery: (start) >> >> [ 2.307559] mpt2sas_cm0: Discovery: (stop) >> >> [ 2.307948] mpt2sas_cm0: Discovery: (start) >> >> [ 2.308336] mpt2sas_cm0: Discovery: (stop) >> >> [ 2.311738] mpt2sas_cm0: host_add: handle(0x0001), sas_addr(0x500605b003683dd0), phys(8) >> [ 2.312097] mpt2sas_cm0: enclosure status change: (enclosure add) >> handle(0x0001), enclosure logical id(0x500605b003683dd0) number slots(0) >> [ 2.312551] mpt2sas_cm0: sas topology change: (responding) >> [ 2.312768] handle(0x0000), enclosure_handle(0x0001) start_phy(00), count(8) >> [ 2.313003] phy(01), attached_handle(0x0009): target add: link rate: new(0x0a), old(0x00) >> [ 2.313250] phy(02), attached_handle(0x000a): target add: link rate: new(0x09), old(0x00) >> [ 2.313498] phy(03), attached_handle(0x000b): target add: link rate: new(0x09), old(0x00) >> [ 2.313745] phy(04), attached_handle(0x000c): target add: link rate: new(0x09), old(0x00) >> [ 2.313992] phy(05), attached_handle(0x000d): target add: link rate: new(0x09), old(0x00) >> [ 2.314248] phy(06), attached_handle(0x000e): target add: link rate: new(0x09), old(0x00) >> [ 2.314495] phy(07), attached_handle(0x000f): target add: link rate: new(0x09), old(0x00) >> [ 2.314747] mpt2sas_cm0: updating handles for sas_host(0x500605b003683dd0) >> [ 2.316041] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x0009), sas_addr(0x4433221101000000) >> [ 2.316465] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 2) >> [ 2.317200] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000a), sas_addr(0x4433221102000000) >> [ 2.317669] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 1) >> [ 2.318431] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000b), sas_addr(0x4433221103000000) >> [ 2.318900] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 0) >> [ 2.319366] mpt2sas_cm0: _scsih_determine_boot_device: current_boot_device(0x4433221103000000) >> [ 2.320151] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000c), sas_addr(0x4433221104000000) >> [ 2.321371] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 7) >> [ 2.322137] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000d), sas_addr(0x4433221105000000) >> [ 2.322606] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 6) >> [ 2.323367] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000e), sas_addr(0x4433221106000000) >> [ 2.323834] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 5) >> [ 2.324602] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000f), sas_addr(0x4433221107000000) >> [ 2.325071] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 4) >> [ 2.325541] mpt2sas_cm0: discovery event: (stop) >> >> [ 2.326017] mpt2sas_cm0: discovery event: (start) >> >> [ 2.326492] mpt2sas_cm0: discovery event: (stop) >> >> [ 2.326975] mpt2sas_cm0: discovery event: (start) >> >> [ 2.327450] mpt2sas_cm0: discovery event: (stop) >> >> [ 2.327923] mpt2sas_cm0: discovery event: (start) >> >> [ 2.328396] mpt2sas_cm0: discovery event: (stop) >> >> [ 2.328868] mpt2sas_cm0: discovery event: (start) >> >> [ 2.329340] mpt2sas_cm0: discovery event: (stop) >> >> [ 2.329816] mpt2sas_cm0: discovery event: (start) >> >> [ 2.330316] mpt2sas_cm0: discovery event: (stop) >> >> [ 2.330797] mpt2sas_cm0: discovery event: (start) >> >> [ 2.331269] mpt2sas_cm0: discovery event: (stop) >> >> [ 2.331740] mpt2sas_cm0: port enable: complete from worker thread >> [ 2.350236] mpt2sas_cm0: port enable: SUCCESS >> [ 2.356432] scsi 0:0:0:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 >> [ 2.356683] scsi 0:0:0:0: SATA: handle(0x000b), sas_addr(0x4433221103000000), phy(3), device_name(0x5000c5000267c9f8) >> [ 2.357080] scsi 0:0:0:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(0) >> [ 2.357405] scsi 0:0:0:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >> [ 2.383043] scsi 0:0:1:0: Direct-Access ATA Hitachi HDS5C302 A800 PQ: 0 ANSI: 6 >> [ 2.383296] scsi 0:0:1:0: SATA: handle(0x0009), sas_addr(0x4433221101000000), phy(1), device_name(0x5000cca369cdd311) >> [ 2.383684] scsi 0:0:1:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(2) >> [ 2.384028] scsi 0:0:1:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >> [ 2.405088] scsi 0:0:2:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 >> [ 2.405346] scsi 0:0:2:0: SATA: handle(0x000a), sas_addr(0x4433221102000000), phy(2), device_name(0x5000c5000ccfbd32) >> [ 2.405735] scsi 0:0:2:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(1) >> [ 2.406082] scsi 0:0:2:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >> [ 2.424125] scsi 0:0:3:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 >> [ 2.424373] scsi 0:0:3:0: SATA: handle(0x000c), sas_addr(0x4433221104000000), phy(4), device_name(0x5000c5000267abee) >> [ 2.424763] scsi 0:0:3:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(7) >> [ 2.425108] scsi 0:0:3:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >> [ 2.444834] scsi 0:0:4:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 >> [ 2.445086] scsi 0:0:4:0: SATA: handle(0x000d), sas_addr(0x4433221105000000), phy(5), device_name(0x5000c50009c0e5e6) >> [ 2.445478] scsi 0:0:4:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(6) >> [ 2.445803] scsi 0:0:4:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >> [ 2.464065] scsi 0:0:5:0: Direct-Access ATA ST3750330NS SN16 PQ: 0 ANSI: 6 >> [ 2.464312] scsi 0:0:5:0: SATA: handle(0x000e), sas_addr(0x4433221106000000), phy(6), device_name(0x5000c5003cb9ac10) >> [ 2.464699] scsi 0:0:5:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(5) >> [ 2.465048] scsi 0:0:5:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >> [ 2.484016] scsi 0:0:6:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 >> [ 2.484266] scsi 0:0:6:0: SATA: handle(0x000f), sas_addr(0x4433221107000000), phy(7), device_name(0x5000c5000839b69e) >> [ 2.484655] scsi 0:0:6:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(4) >> [ 2.485001] scsi 0:0:6:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >> [ 2.500660] mpt2sas_cm1: mpt3sas_base_attach >> [ 2.500861] mpt2sas_cm1: mpt3sas_base_map_resources >> [ 2.501599] mpt2sas_cm1: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3074748 kB) >> [ 2.501847] mpt2sas_cm1: _base_get_ioc_facts >> [ 2.502036] mpt2sas_cm1: _base_wait_for_iocstate >> [ 2.559080] offset:data >> [ 2.559318] [0x00]:03100200 >> [ 2.559552] [0x04]:00002300 >> [ 2.559785] [0x08]:00000000 >> [ 2.560020] [0x0c]:00000000 >> [ 2.560277] [0x10]:00000000 >> [ 2.560511] [0x14]:00010480 >> [ 2.560745] [0x18]:22130d68 >> [ 2.560978] [0x1c]:0001285c >> [ 2.561210] [0x20]:14000400 >> [ 2.561443] [0x24]:00000020 >> [ 2.561675] [0x28]:0100000f >> [ 2.561907] [0x2c]:000c000b >> [ 2.562139] [0x30]:003c0003 >> [ 2.562371] [0x34]:0020ffe0 >> [ 2.562602] [0x38]:00800122 >> [ 2.562839] [0x3c]:00000009 >> [ 2.563073] mpt2sas_cm1: hba queue depth(3432), max chains per io(128) >> [ 2.563355] mpt2sas_cm1: request frame size(128), reply frame size(128) >> [ 2.563745] mpt2sas_cm1: msix is supported, vector_count(1) >> [ 2.564016] mpt2sas_cm1: MSI-X vectors supported: 1, no of cores: 4, max_msix_vectors: 8 >> [ 2.564918] mpt2sas1-msix0: PCI-MSI-X enabled: IRQ 59 >> [ 2.566189] mpt2sas_cm1: iomem(0x00000000fd1fc000), mapped(0xffffc900000d8000), size(16384) >> [ 2.566498] mpt2sas_cm1: ioport(0x0000000000007000), size(256) >> [ 2.567328] mpt2sas_cm1: _base_get_ioc_facts >> [ 2.567583] mpt2sas_cm1: _base_wait_for_iocstate >> [ 2.625125] offset:data >> [ 2.625364] [0x00]:03100200 >> [ 2.625597] [0x04]:00002300 >> [ 2.625830] [0x08]:00000000 >> [ 2.626064] [0x0c]:00000000 >> [ 2.626296] [0x10]:00000000 >> [ 2.626529] [0x14]:00010480 >> [ 2.626769] [0x18]:22130d68 >> [ 2.627002] [0x1c]:0001285c >> [ 2.627235] [0x20]:14000400 >> [ 2.627467] [0x24]:00000020 >> [ 2.627702] [0x28]:0100000f >> [ 2.627936] [0x2c]:000c000b >> [ 2.628170] [0x30]:003c0003 >> [ 2.628403] [0x34]:0020ffe0 >> [ 2.628638] [0x38]:00800122 >> [ 2.628872] [0x3c]:00000009 >> [ 2.629107] mpt2sas_cm1: hba queue depth(3432), max chains per io(128) >> [ 2.629388] mpt2sas_cm1: request frame size(128), reply frame size(128) >> [ 2.629671] mpt2sas_cm1: _base_make_ioc_ready >> [ 2.629928] mpt2sas_cm1: _base_get_port_facts >> [ 2.660127] offset:data >> [ 2.660389] [0x00]:05070000 >> [ 2.660623] [0x04]:00000000 >> [ 2.660858] [0x08]:00000000 >> [ 2.661093] [0x0c]:00000000 >> [ 2.661326] [0x10]:00000000 >> [ 2.661562] [0x14]:00003000 >> [ 2.661796] [0x18]:00000078 >> [ 2.664346] mpt2sas_cm1: _base_allocate_memory_pools >> [ 2.664608] mpt2sas_cm1: scatter gather: sge_in_main_msg(3), sge_per_chain(15), sge_per_io(128), chains_per_io(9) >> [ 2.665142] mpt2sas_cm1: reply post free pool (0xffff8800b8b10000): depth(6944),element_size(8), pool_size(54 kB) >> [ 2.666671] mpt2sas_cm1: reply_post_free_dma = (0xb8b10000) >> [ 2.666954] mpt2sas_cm1: scsi host: can_queue depth (3307) >> [ 2.667311] mpt2sas_cm1: request pool(0xffff8800b8b80000): depth(3432), frame_size(128), pool_size(429 kB) >> [ 2.667813] mpt2sas_cm1: request pool: dma(0xb8b80000) >> [ 2.668080] mpt2sas_cm1: scsiio(0xffff8800b8b80000): depth(3307) >> [ 2.674131] mpt2sas_cm1: chain pool depth(29763), frame_size(128), pool_size(3720 kB) >> [ 2.674448] mpt2sas_cm1: hi_priority(0xffff8800b8be7600): depth(60), start smid(3308) >> [ 2.674750] mpt2sas_cm1: internal(0xffff8800b8be9400): depth(65), start smid(3368) >> [ 2.675105] mpt2sas_cm1: sense pool(0xffff8800b8100000): depth(3307), element_size(96), pool_size(310 kB) >> [ 2.675605] mpt2sas_cm1: sense_dma(0xb8100000) >> [ 2.675944] mpt2sas_cm1: reply pool(0xffff8800b8180000): depth(3496), frame_size(128), pool_size(437 kB) >> [ 2.676443] mpt2sas_cm1: reply_dma(0xb8180000) >> [ 2.676702] mpt2sas_cm1: reply_free pool(0xffff8800b80a0000): depth(3496), element_size(4), pool_size(13 kB) >> [ 2.677124] mpt2sas_cm1: reply_free_dma (0xb80a0000) >> [ 2.677322] mpt2sas_cm1: config page(0xffff8800b807f000): size(512) >> [ 2.677532] mpt2sas_cm1: config_page_dma(0xb807f000) >> [ 2.677728] mpt2sas_cm1: Allocated physical memory: size(4964 kB) >> [ 2.677936] mpt2sas_cm1: Current Controller Queue Depth(3307),Max Controller Queue Depth(3432) >> [ 2.678304] mpt2sas_cm1: Scatter Gather Elements per IO(128) >> [ 2.678514] mpt2sas_cm1: _base_make_ioc_operational >> [ 2.679081] mpt2sas_cm1: _base_send_ioc_init >> [ 2.679275] offset:data >> [ 2.679448] [0x00]:02000004 >> [ 2.679625] [0x04]:00000000 >> [ 2.679805] [0x08]:00000000 >> [ 2.681200] [0x0c]:23000200 >> [ 2.681377] [0x10]:00000000 >> [ 2.681554] [0x14]:00000000 >> [ 2.681729] [0x18]:00200000 >> [ 2.681906] [0x1c]:0da81b20 >> [ 2.682082] [0x20]:00000000 >> [ 2.682259] [0x24]:00000000 >> [ 2.682435] [0x28]:b8b80000 >> [ 2.682611] [0x2c]:00000000 >> [ 2.682787] [0x30]:b8b10000 >> [ 2.682963] [0x34]:00000000 >> [ 2.683139] [0x38]:b80a0000 >> [ 2.683314] [0x3c]:00000000 >> [ 2.683489] [0x40]:98597011 >> [ 2.683665] [0x44]:00000153 >> [ 2.729849] offset:data >> [ 2.730089] [0x00]:02050004 >> [ 2.730349] [0x04]:00000000 >> [ 2.730586] [0x08]:00000000 >> [ 2.730822] [0x0c]:00000000 >> [ 2.731058] [0x10]:00000000 >> [ 2.731295] mpt2sas_cm1: _base_event_notification >> [ 2.731606] mpt2sas_cm1: _base_event_notification: complete >> [ 2.732501] mpt2sas_cm1: LSISAS2008: FWVersion(20.00.04.00), ChipRevision(0x02), BiosVersion(07.39.00.00) >> [ 2.733010] mpt2sas_cm1: Protocol=( >> [ 2.733074] Initiator >> [ 2.733339] ,Target >> [ 2.733384] ), >> [ 2.733642] Capabilities=( >> [ 2.733696] TLR >> [ 2.733952] ,EEDP >> [ 2.733995] ,Snapshot Buffer >> [ 2.734268] ,Diag Trace Buffer >> [ 2.734326] ,Task Set Full >> [ 2.734595] ,NCQ >> [ 2.734637] ) >> [ 2.735155] scsi host1: Fusion MPT SAS Host >> [ 2.749047] mpt2sas_cm1: sending port enable !! >> [ 2.749563] mpt2sas_cm1: Discovery: (start) >> >> [ 2.749989] mpt2sas_cm1: SAS Enclosure Device Status Change >> [ 2.750001] mpt2sas_cm1: discovery event: (start) >> >> [ 2.750578] mpt2sas_cm1: SAS Topology Change List >> [ 2.750788] mpt2sas_cm1: Discovery: (stop) >> >> [ 2.751181] mpt2sas_cm1: Discovery: (start) >> >> [ 2.751571] mpt2sas_cm1: Discovery: (stop) >> >> [ 2.752002] mpt2sas_cm1: Discovery: (start) >> >> [ 2.752391] mpt2sas_cm1: Discovery: (stop) >> >> [ 2.752779] mpt2sas_cm1: Discovery: (start) >> >> [ 2.754205] mpt2sas_cm1: Discovery: (stop) >> >> [ 2.754593] mpt2sas_cm1: Discovery: (start) >> >> [ 2.754983] mpt2sas_cm1: Discovery: (stop) >> >> [ 2.755371] mpt2sas_cm1: Discovery: (start) >> >> [ 2.755762] mpt2sas_cm1: Discovery: (stop) >> >> [ 2.759602] mpt2sas_cm1: host_add: handle(0x0001), sas_addr(0x500605b0026f79b0), phys(8) >> [ 2.759969] mpt2sas_cm1: enclosure status change: (enclosure add) >> handle(0x0001), enclosure logical id(0x500605b0026f79b0) number slots(0) >> [ 2.760407] mpt2sas_cm1: sas topology change: (responding) >> [ 2.760612] handle(0x0000), enclosure_handle(0x0001) start_phy(00), count(8) >> [ 2.760834] phy(02), attached_handle(0x000e): target add: link rate: new(0x0a), old(0x00) >> [ 2.761066] phy(03), attached_handle(0x000b): target add: link rate: new(0x0a), old(0x00) >> [ 2.761304] phy(04), attached_handle(0x000d): target add: link rate: new(0x09), old(0x00) >> [ 2.761538] phy(05), attached_handle(0x0009): target add: link rate: new(0x09), old(0x00) >> [ 2.761771] phy(06), attached_handle(0x000a): target add: link rate: new(0x09), old(0x00) >> [ 2.762002] phy(07), attached_handle(0x000c): target add: link rate: new(0x09), old(0x00) >> [ 2.762235] mpt2sas_cm1: updating handles for sas_host(0x500605b0026f79b0) >> [ 2.763653] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x000e), sas_addr(0x4433221102000000) >> [ 2.764036] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 1) >> [ 2.764772] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x000b), sas_addr(0x4433221103000000) >> [ 2.765147] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 0) >> [ 2.765891] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x000d), sas_addr(0x4433221104000000) >> [ 2.767250] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 7) >> [ 2.768009] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x0009), sas_addr(0x4433221105000000) >> [ 2.768394] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 6) >> [ 2.769136] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x000a), sas_addr(0x4433221106000000) >> [ 2.769510] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 5) >> [ 2.769888] mpt2sas_cm1: _scsih_determine_boot_device: current_boot_device(0x4433221106000000) >> [ 2.770641] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x000c), sas_addr(0x4433221107000000) >> [ 2.771025] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 4) >> [ 2.771405] mpt2sas_cm1: discovery event: (stop) >> >> [ 2.771788] mpt2sas_cm1: discovery event: (start) >> >> [ 2.772172] mpt2sas_cm1: discovery event: (stop) >> >> [ 2.772554] mpt2sas_cm1: discovery event: (start) >> >> [ 2.772942] mpt2sas_cm1: discovery event: (stop) >> >> [ 2.773326] mpt2sas_cm1: discovery event: (start) >> >> [ 2.773709] mpt2sas_cm1: discovery event: (stop) >> >> [ 2.774090] mpt2sas_cm1: discovery event: (start) >> >> [ 2.774474] mpt2sas_cm1: discovery event: (stop) >> >> [ 2.774855] mpt2sas_cm1: discovery event: (start) >> >> [ 2.775237] mpt2sas_cm1: discovery event: (stop) >> >> [ 2.775619] mpt2sas_cm1: port enable: complete from worker thread >> [ 2.780192] mpt2sas_cm1: port enable: SUCCESS >> [ 2.782404] scsi 1:0:0:0: Direct-Access ATA Hitachi HDP72505 A5BA PQ: 0 ANSI: 6 >> [ 2.782651] scsi 1:0:0:0: SATA: handle(0x000a), sas_addr(0x4433221106000000), phy(6), device_name(0x5000cca34dc05584) >> [ 2.783039] scsi 1:0:0:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(5) >> [ 2.783390] scsi 1:0:0:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >> [ 2.803032] scsi 1:0:1:0: Direct-Access ATA ST8000AS0002-1NA AR15 PQ: 0 ANSI: 6 >> [ 2.803272] scsi 1:0:1:0: SATA: handle(0x000e), sas_addr(0x4433221102000000), phy(2), device_name(0x5000c500908f1d05) >> [ 2.803660] scsi 1:0:1:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(1) >> [ 2.803981] scsi 1:0:1:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >> [ 2.821712] scsi 1:0:2:0: Direct-Access ATA ST3000DM001-1CH1 CC43 PQ: 0 ANSI: 6 >> [ 2.821963] scsi 1:0:2:0: SATA: handle(0x000b), sas_addr(0x4433221103000000), phy(3), device_name(0x5000c5004dfd2a8a) >> [ 2.822352] scsi 1:0:2:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(0) >> [ 2.822694] scsi 1:0:2:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >> [ 2.844233] scsi 1:0:3:0: Direct-Access ATA ST3500320NS SN16 PQ: 0 ANSI: 6 >> [ 2.844483] scsi 1:0:3:0: SATA: handle(0x000d), sas_addr(0x4433221104000000), phy(4), device_name(0x5000c50009dca65b) >> [ 2.844870] scsi 1:0:3:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(7) >> [ 2.845216] scsi 1:0:3:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >> [ 2.868963] scsi 1:0:4:0: Direct-Access ATA SAMSUNG HD401LJ 0-15 PQ: 0 ANSI: 6 >> [ 2.870994] scsi 1:0:4:0: SATA: handle(0x0009), sas_addr(0x4433221105000000), phy(5), device_name(0x695d550daf678093) >> [ 2.871382] scsi 1:0:4:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(6) >> [ 2.871728] scsi 1:0:4:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >> [ 2.894004] scsi 1:0:5:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 >> [ 2.894257] scsi 1:0:5:0: SATA: handle(0x000c), sas_addr(0x4433221107000000), phy(7), device_name(0x5000c5000266bb02) >> [ 2.894646] scsi 1:0:5:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(4) >> [ 2.894972] scsi 1:0:5:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) > > I don't see a clear pattern yet, but I suspect warm rebooting >=4.2 > after having run 4.1.x leads to sucessful driver inits. But I also > remember having had cold boots, with kernels >=4.2 that worked fine > (obviously not all of the time). <=4.1.20 kernels on the other hand boot > fine every single time. > > Interestingly the igb driver (ethernet) seems to be acting up at least > with 4.5.0 on exactly the same boots when mpt2sas init fails. I don't > know whether this could be connected or not (I just became aware of this > coincidence). > > > --- > Matthias > > > Am 21.03.2016 um 05:53 schrieb Sreekanth Reddy: >> Hi Matthias, >> >> Can you please share us the driver logs with driver logging_level set >> to 0x3f8. So that we can get more info from this log. >> >> Thanks, >> Sreekanth >> >> On Mon, Mar 21, 2016 at 1:44 AM, Matthias Prager >> <linux@matthiasprager.de> wrote: >>> Hello, >>> >>> I don't know what's the correct procedure, whether I should file a bug or first report this issue on the kernel mailing-list. So please feel free to tell me to open a ticket in the bugtracker (bugzilla.kernel.org?). >>> >>> But first let me present the issue I encounter: >>> >>> Kernels >= 4.2 (4.2.1 was the first on I tried, but also 4.3, 4.4 and 4.5) fail to load the mpt2sas driver on most (but not all) boots. Kernels <= 4.1.x work fine every single time (4.1.19 was the latest I tried, also 3.18.29). >>> >>> Here is the dmesg output for a failed driver init with Kernel 4.5.0: >>>> [ 2.068313] mpt3sas version 09.102.00.00 loaded >>>> [ 2.069412] mpt2sas_cm0: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3074748 kB) >>>> [ 2.125260] mpt2sas_cm0: MSI-X vectors supported: 1, no of cores: 4, max_msix_vectors: -1 >>>> [ 2.125996] mpt2sas0-msix0: PCI-MSI-X enabled: IRQ 58 >>>> [ 2.126199] mpt2sas_cm0: iomem(0x00000000fd4fc000), mapped(0xffffc900000d0000), size(16384) >>>> [ 2.126430] mpt2sas_cm0: ioport(0x0000000000004000), size(256) >>>> [ 2.216371] mpt2sas_cm0: Allocated physical memory: size(4964 kB) >>>> [ 2.216600] mpt2sas_cm0: Current Controller Queue Depth(3307),Max Controller Queue Depth(3432) >>>> [ 2.217004] mpt2sas_cm0: Scatter Gather Elements per IO(128) >>>> [ 5.086959] floppy0: no floppy controllers found >>>> [ 32.256720] mpt2sas_cm0: _base_event_notification: timeout >>>> [ 32.256940] mf: >>>> >>>> [ 32.257106] 07000000 >>>> [ 32.257302] 00000000 >>>> [ 32.257337] 00000000 >>>> [ 32.257533] 00000000 >>>> [ 32.257568] 00000000 >>>> [ 32.257764] 0f2f7fff >>>> [ 32.257800] ffffff7c >>>> [ 32.257995] ffffffff >>>> [ 32.258031] >>>> >>>> [ 32.258352] ffffffff >>>> [ 32.258387] 00000000 >>>> [ 32.258582] 00000000 >>>> >>>> [ 32.258950] mpt2sas_cm0: sending message unit reset !! >>>> [ 32.260688] mpt2sas_cm0: message unit reset: SUCCESS >>>> [ 32.325956] mpt2sas_cm0: failure at drivers/scsi/mpt3sas/mpt3sas_scsih.c:8592/_scsih_probe()! >>> >>> For comparison here is a dmesg output for a successful boot on Kernel 4.1.15: >>>> [ 2.035568] mpt2sas version 20.100.00.00 loaded >>>> [ 2.037243] mpt2sas0: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (2046352 kB) >>>> [ 2.755374] mpt2sas0: MSI-X vectors supported: 1, no of cores: 3, max_msix_vectors: 8 >>>> [ 2.756377] mpt2sas0-msix0: PCI-MSI-X enabled: IRQ 58 >>>> [ 2.756708] mpt2sas0: iomem(0x00000000fd5fc000), mapped(0xffffc900000d0000), size(16384) >>>> [ 2.757083] mpt2sas0: ioport(0x0000000000004000), size(256) >>>> [ 3.842944] mpt2sas0: Allocated physical memory: size(4964 kB) >>>> [ 3.843303] mpt2sas0: Current Controller Queue Depth(3307), Max Controller Queue Depth(3432) >>>> [ 3.843717] mpt2sas0: Scatter Gather Elements per IO(128) >>>> [ 4.415980] mpt2sas0: LSISAS2008: FWVersion(20.00.04.00), ChipRevision(0x03), BiosVersion(07.39.00.00) >>>> [ 4.416618] mpt2sas0: Protocol=(Initiator,Target), Capabilities=(TLR,EEDP,Snapshot Buffer,Diag Trace Buffer,Task Set Full,NCQ) >>>> [ 4.417846] scsi host0: Fusion MPT SAS Host >>>> [ 4.436865] mpt2sas0: sending port enable !! >>>> [ 4.440460] mpt2sas0: host_add: handle(0x0001), sas_addr(0xxxxxxxxxxxxxxxxx), phys(8) >>>> >>>> ... >>>> [ 4.444045] scsi 0:0:0:0: Direct-Access ATA Hitachi HDS5C302 A800 PQ: 0 ANSI: 6 >>>> [ 4.444338] scsi 0:0:0:0: SATA: handle(0x0009), sas_addr(0xxxxxxxxxxxxxxxxx), phy(1), device_name(0xxxxxxxxxxxxxxxxx) >>>> [ 4.444823] scsi 0:0:0:0: SATA: enclosure_logical_id(0xxxxxxxxxxxxxxxxx), slot(2) >>>> [ 4.445197] scsi 0:0:0:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>> ... (n times for n drives) >>>> >>>> [ 4.515443] mpt2sas0: port enable: SUCCESS >>> >>> >>> The Controller(s) are all Avego/LSI 9211-8i running the latest version of IT firmware (v20.00.04.00). These are passed through to a gentoo-linux VM on an ESXi 5.1 host (latest patchlevel). I have two of these systems (one production one testing) with nearly identical hardware (Supermicro X8DTi-F boards with 2x Intel Westmere CPUs). I also have an older set of systems running the same software config (Intel S3200SHLC boards with single Core2Quad) which exhibit the same buggy behavior. >>> >>> The 'uname -a' line on the current testing system looks like this: >>>> Linux pserver2 4.1.19-gentoo #4 SMP Thu Mar 17 16:02:48 CET 2016 x86_64 Intel(R) Xeon(R) CPU E5506 @ 2.13GHz GenuineIntel GNU/Linux >>> p >>> >>> There seem to be other people with similar issues: >>> <https://bbs.archlinux.org/viewtopic.php?id=209495> >>> >>> Any thoughts? >>> >>> --- >>> Matthias > ^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [BUG] mpt2sas: driver init fails on kernel >=4.2 for 9211-8i IT 2016-03-21 13:59 ` Sreekanth Reddy @ 2016-03-21 15:52 ` Matthias Prager 2016-03-21 16:30 ` Matthias Prager 0 siblings, 1 reply; 13+ messages in thread From: Matthias Prager @ 2016-03-21 15:52 UTC (permalink / raw) To: Sreekanth Reddy; +Cc: linux-scsi, Matthias Prager Hi Sreekanth, thanks for digging into this issue. Regarding the 4.5.0 after 4.1.20 boot statement, I will try to express myself better: I first started the system with the 4.1.20 kernel. Then I issued an 'init 6' warm-reboot and chose to boot the 4.5.0 kernel. This procedure often works (i.e. I'm able to boot the newer kernels (>=4.2) this way with mpt2sas initializing just fine). I will try the msix_disable parameter and report back. Maybe kernel version 4.2 broke interrupt handling somehow? --- Matthias Am 21.03.2016 um 14:59 schrieb Sreekanth Reddy: > Hi Matthias, > > Thanks for providing the logs. In these logs, I am not observing any > such a prints which should be suspected for this issue. > > Can you please try once by setting mpt3sas driver's "msix_disable" > module parameter to one. > > Also, can you please elaborate below statement for me, I am not able > understand this statement > "I managed to boot the same 4.5.0 kernel successfully after warm > rebooting from 4.1.20" > > Thanks, > Sreekanth > > On Mon, Mar 21, 2016 at 2:48 PM, Matthias Prager > <linux@matthiasprager.de> wrote: >> Hi Sreekanth, >> >> thank you for replying so quickly. Here are the logs you requested >> (kernel 4.5.0): >> >>> [ 2.083177] mpt3sas version 09.102.00.00 loaded >>> [ 2.083757] mpt2sas_cm0: mpt3sas_base_attach >>> [ 2.083956] mpt2sas_cm0: mpt3sas_base_map_resources >>> [ 2.084708] mpt2sas_cm0: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3074748 kB) >>> [ 2.084964] mpt2sas_cm0: _base_get_ioc_facts >>> [ 2.085154] mpt2sas_cm0: _base_wait_for_iocstate >>> [ 2.140893] offset:data >>> [ 2.141082] [0x00]:03100200 >>> [ 2.141257] [0x04]:00002300 >>> [ 2.141432] [0x08]:00000000 >>> [ 2.141606] [0x0c]:00000000 >>> [ 2.141780] [0x10]:00000000 >>> [ 2.141955] [0x14]:00010480 >>> [ 2.142129] [0x18]:22130d68 >>> [ 2.142303] [0x1c]:0001285c >>> [ 2.142477] [0x20]:14000400 >>> [ 2.142651] [0x24]:00000020 >>> [ 2.142825] [0x28]:0100000f >>> [ 2.143000] [0x2c]:000c000b >>> [ 2.143174] [0x30]:003c0003 >>> [ 2.143349] [0x34]:0020ffe0 >>> [ 2.143544] [0x38]:00800122 >>> [ 2.143719] [0x3c]:00000009 >>> [ 2.143895] mpt2sas_cm0: hba queue depth(3432), max chains per io(128) >>> [ 2.144106] mpt2sas_cm0: request frame size(128), reply frame size(128) >>> [ 2.144397] mpt2sas_cm0: msix is supported, vector_count(1) >>> [ 2.144600] mpt2sas_cm0: MSI-X vectors supported: 1, no of cores: 4, max_msix_vectors: -1 >>> [ 2.145161] mpt2sas0-msix0: PCI-MSI-X enabled: IRQ 58 >>> [ 2.145361] mpt2sas_cm0: iomem(0x00000000fd4fc000), mapped(0xffffc900000d0000), size(16384) >>> [ 2.145591] mpt2sas_cm0: ioport(0x0000000000004000), size(256) >>> [ 2.146206] mpt2sas_cm0: _base_get_ioc_facts >>> [ 2.146397] mpt2sas_cm0: _base_wait_for_iocstate >>> [ 2.202087] offset:data >>> [ 2.202281] [0x00]:03100200 >>> [ 2.202456] [0x04]:00002300 >>> [ 2.202631] [0x08]:00000000 >>> [ 2.202805] [0x0c]:00000000 >>> [ 2.202980] [0x10]:00000000 >>> [ 2.203154] [0x14]:00010480 >>> [ 2.203328] [0x18]:22130d68 >>> [ 2.203521] [0x1c]:0001285c >>> [ 2.203695] [0x20]:14000400 >>> [ 2.203870] [0x24]:00000020 >>> [ 2.204044] [0x28]:0100000f >>> [ 2.204219] [0x2c]:000c000b >>> [ 2.204394] [0x30]:003c0003 >>> [ 2.204571] [0x34]:0020ffe0 >>> [ 2.204746] [0x38]:00800122 >>> [ 2.204926] [0x3c]:00000009 >>> [ 2.205102] mpt2sas_cm0: hba queue depth(3432), max chains per io(128) >>> [ 2.205314] mpt2sas_cm0: request frame size(128), reply frame size(128) >>> [ 2.205528] mpt2sas_cm0: _base_make_ioc_ready >>> [ 2.205719] mpt2sas_cm0: _base_get_port_facts >>> [ 2.234205] offset:data >>> [ 2.234397] [0x00]:05070000 >>> [ 2.234573] [0x04]:00000000 >>> [ 2.234748] [0x08]:00000000 >>> [ 2.234928] [0x0c]:00000000 >>> [ 2.235103] [0x10]:00000000 >>> [ 2.235278] [0x14]:00003000 >>> [ 2.235453] [0x18]:00000078 >>> [ 2.235629] mpt2sas_cm0: _base_allocate_memory_pools >>> [ 2.235826] mpt2sas_cm0: scatter gather: sge_in_main_msg(3), sge_per_chain(15), sge_per_io(128), chains_per_io(9) >>> [ 2.236227] mpt2sas_cm0: reply post free pool (0xffff8800bb380000): depth(6944),element_size(8), pool_size(54 kB) >>> [ 2.236611] mpt2sas_cm0: reply_post_free_dma = (0xbb380000) >>> [ 2.236813] mpt2sas_cm0: scsi host: can_queue depth (3307) >>> [ 2.237086] mpt2sas_cm0: request pool(0xffff8800ba880000): depth(3432), frame_size(128), pool_size(429 kB) >>> [ 2.238580] mpt2sas_cm0: request pool: dma(0xba880000) >>> [ 2.238781] mpt2sas_cm0: scsiio(0xffff8800ba880000): depth(3307) >>> [ 2.243644] mpt2sas_cm0: chain pool depth(29763), frame_size(128), pool_size(3720 kB) >>> [ 2.243887] mpt2sas_cm0: hi_priority(0xffff8800ba8e7600): depth(60), start smid(3308) >>> [ 2.244113] mpt2sas_cm0: internal(0xffff8800ba8e9400): depth(65), start smid(3368) >>> [ 2.244390] mpt2sas_cm0: sense pool(0xffff8800ba480000): depth(3307), element_size(96), pool_size(310 kB) >>> [ 2.244774] mpt2sas_cm0: sense_dma(0xba480000) >>> [ 2.245038] mpt2sas_cm0: reply pool(0xffff8800ba500000): depth(3496), frame_size(128), pool_size(437 kB) >>> [ 2.245413] mpt2sas_cm0: reply_dma(0xba500000) >>> [ 2.245608] mpt2sas_cm0: reply_free pool(0xffff8800ba430000): depth(3496), element_size(4), pool_size(13 kB) >>> [ 2.245985] mpt2sas_cm0: reply_free_dma (0xba430000) >>> [ 2.246181] mpt2sas_cm0: config page(0xffff8800ba429000): size(512) >>> [ 2.246389] mpt2sas_cm0: config_page_dma(0xba429000) >>> [ 2.246584] mpt2sas_cm0: Allocated physical memory: size(4964 kB) >>> [ 2.246791] mpt2sas_cm0: Current Controller Queue Depth(3307),Max Controller Queue Depth(3432) >>> [ 2.247155] mpt2sas_cm0: Scatter Gather Elements per IO(128) >>> [ 2.247361] mpt2sas_cm0: _base_make_ioc_operational >>> [ 2.247962] mpt2sas_cm0: _base_send_ioc_init >>> [ 2.248154] offset:data >>> [ 2.248325] [0x00]:02000004 >>> [ 2.248499] [0x04]:00000000 >>> [ 2.248673] [0x08]:00000000 >>> [ 2.248848] [0x0c]:23000200 >>> [ 2.249023] [0x10]:00000000 >>> [ 2.249197] [0x14]:00000000 >>> [ 2.249372] [0x18]:00200000 >>> [ 2.249546] [0x1c]:0da81b20 >>> [ 2.249720] [0x20]:00000000 >>> [ 2.249894] [0x24]:00000000 >>> [ 2.250068] [0x28]:ba880000 >>> [ 2.250242] [0x2c]:00000000 >>> [ 2.250416] [0x30]:bb380000 >>> [ 2.250589] [0x34]:00000000 >>> [ 2.250768] [0x38]:ba430000 >>> [ 2.250941] [0x3c]:00000000 >>> [ 2.251115] [0x40]:983eb686 >>> [ 2.251288] [0x44]:00000153 >>> [ 2.296610] offset:data >>> [ 2.296795] [0x00]:02050004 >>> [ 2.296969] [0x04]:00000000 >>> [ 2.297143] [0x08]:00000000 >>> [ 2.297318] [0x0c]:00000000 >>> [ 2.297493] [0x10]:00000000 >>> [ 2.297668] mpt2sas_cm0: _base_event_notification >>> [ 5.093707] floppy0: no floppy controllers found >>> [ 32.293619] mpt2sas_cm0: _base_event_notification: timeout >>> [ 32.293909] mf: >>> >>> [ 32.294132] 07000000 >>> [ 32.294397] 00000000 >>> [ 32.294445] 00000000 >>> [ 32.294719] 00000000 >>> [ 32.294767] 00000000 >>> [ 32.295031] 0f2f7fff >>> [ 32.295078] ffffff7c >>> [ 32.295342] ffffffff >>> [ 32.295389] >>> >>> [ 32.295823] ffffffff >>> [ 32.295871] 00000000 >>> [ 32.296134] 00000000 >>> >>> [ 32.296615] mpt2sas_cm0: mpt3sas_base_free_resources >>> [ 32.296880] mpt2sas_cm0: _base_make_ioc_ready >>> [ 32.297135] mpt2sas_cm0: sending message unit reset !! >>> [ 32.298941] mpt2sas_cm0: message unit reset: SUCCESS >>> [ 32.299212] mpt2sas_cm0: mpt3sas_base_unmap_resources >>> [ 32.300381] mpt2sas_cm0: _base_release_memory_pools >>> [ 32.300654] mpt2sas_cm0: request_pool(0xffff8800ba880000): free >>> [ 32.300934] mpt2sas_cm0: sense_pool(0xffff8800ba480000): free >>> [ 32.301211] mpt2sas_cm0: reply_pool(0xffff8800ba500000): free >>> [ 32.301485] mpt2sas_cm0: reply_free_pool(0xffff8800ba430000): free >>> [ 32.301774] mpt2sas_cm0: reply_post_free_pool(0xffff8800bb380000): free >>> [ 32.302061] mpt2sas_cm0: config_page(0xffff8800ba429000): free >>> [ 32.371097] mpt2sas_cm0: failure at drivers/scsi/mpt3sas/mpt3sas_scsih.c:8592/_scsih_probe()! >>> [ 32.371958] mpt2sas_cm1: mpt3sas_base_attach >>> [ 32.372154] mpt2sas_cm1: mpt3sas_base_map_resources >>> [ 32.372950] mpt2sas_cm1: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3074748 kB) >>> [ 32.373201] mpt2sas_cm1: _base_get_ioc_facts >>> [ 32.375261] mpt2sas_cm1: _base_wait_for_iocstate >>> [ 32.432012] offset:data >>> [ 32.432262] [0x00]:03100200 >>> [ 32.432499] [0x04]:00002300 >>> [ 32.432735] [0x08]:00000000 >>> [ 32.432971] [0x0c]:00000000 >>> [ 32.433206] [0x10]:00000000 >>> [ 32.433443] [0x14]:00010480 >>> [ 32.433701] [0x18]:22130d68 >>> [ 32.433937] [0x1c]:0001285c >>> [ 32.435434] [0x20]:14000400 >>> [ 32.435674] [0x24]:00000020 >>> [ 32.435909] [0x28]:0100000f >>> [ 32.436144] [0x2c]:000c000b >>> [ 32.436379] [0x30]:003c0003 >>> [ 32.436615] [0x34]:0020ffe0 >>> [ 32.436850] [0x38]:00800122 >>> [ 32.437085] [0x3c]:00000009 >>> [ 32.437322] mpt2sas_cm1: hba queue depth(3432), max chains per io(128) >>> [ 32.437607] mpt2sas_cm1: request frame size(128), reply frame size(128) >>> [ 32.438014] mpt2sas_cm1: msix is supported, vector_count(1) >>> [ 32.438288] mpt2sas_cm1: MSI-X vectors supported: 1, no of cores: 4, max_msix_vectors: 8 >>> [ 32.439101] mpt2sas1-msix0: PCI-MSI-X enabled: IRQ 58 >>> [ 32.439373] mpt2sas_cm1: iomem(0x00000000fd1fc000), mapped(0xffffc900000d8000), size(16384) >>> [ 32.439682] mpt2sas_cm1: ioport(0x0000000000007000), size(256) >>> [ 32.440504] mpt2sas_cm1: _base_get_ioc_facts >>> [ 32.440765] mpt2sas_cm1: _base_wait_for_iocstate >>> [ 32.499305] offset:data >>> [ 32.499557] [0x00]:03100200 >>> [ 32.499794] [0x04]:00002300 >>> [ 32.500031] [0x08]:00000000 >>> [ 32.500267] [0x0c]:00000000 >>> [ 32.500504] [0x10]:00000000 >>> [ 32.500740] [0x14]:00010480 >>> [ 32.500974] [0x18]:22130d68 >>> [ 32.501209] [0x1c]:0001285c >>> [ 32.501444] [0x20]:14000400 >>> [ 32.501687] [0x24]:00000020 >>> [ 32.501922] [0x28]:0100000f >>> [ 32.502157] [0x2c]:000c000b >>> [ 32.502391] [0x30]:003c0003 >>> [ 32.502626] [0x34]:0020ffe0 >>> [ 32.502862] [0x38]:00800122 >>> [ 32.503098] [0x3c]:00000009 >>> [ 32.503336] mpt2sas_cm1: hba queue depth(3432), max chains per io(128) >>> [ 32.503644] mpt2sas_cm1: request frame size(128), reply frame size(128) >>> [ 32.503933] mpt2sas_cm1: _base_make_ioc_ready >>> [ 32.504191] mpt2sas_cm1: _base_get_port_facts >>> [ 32.534282] offset:data >>> [ 32.534537] [0x00]:05070000 >>> [ 32.534782] [0x04]:00000000 >>> [ 32.535058] [0x08]:00000000 >>> [ 32.536473] [0x0c]:00000000 >>> [ 32.536710] [0x10]:00000000 >>> [ 32.536946] [0x14]:00003000 >>> [ 32.537183] [0x18]:00000078 >>> [ 32.537420] mpt2sas_cm1: _base_allocate_memory_pools >>> [ 32.537686] mpt2sas_cm1: scatter gather: sge_in_main_msg(3), sge_per_chain(15), sge_per_io(128), chains_per_io(9) >>> [ 32.538232] mpt2sas_cm1: reply post free pool (0xffff8800bb3d0000): depth(6944),element_size(8), pool_size(54 kB) >>> [ 32.538758] mpt2sas_cm1: reply_post_free_dma = (0xbb3d0000) >>> [ 32.539030] mpt2sas_cm1: scsi host: can_queue depth (3307) >>> [ 32.539378] mpt2sas_cm1: request pool(0xffff8800ba480000): depth(3432), frame_size(128), pool_size(429 kB) >>> [ 32.539882] mpt2sas_cm1: request pool: dma(0xba480000) >>> [ 32.540149] mpt2sas_cm1: scsiio(0xffff8800ba480000): depth(3307) >>> [ 32.545893] mpt2sas_cm1: chain pool depth(29763), frame_size(128), pool_size(3720 kB) >>> [ 32.546137] mpt2sas_cm1: hi_priority(0xffff8800ba4e7600): depth(60), start smid(3308) >>> [ 32.546365] mpt2sas_cm1: internal(0xffff8800ba4e9400): depth(65), start smid(3368) >>> [ 32.546651] mpt2sas_cm1: sense pool(0xffff8800ba880000): depth(3307), element_size(96), pool_size(310 kB) >>> [ 32.547030] mpt2sas_cm1: sense_dma(0xba880000) >>> [ 32.547537] mpt2sas_cm1: reply pool(0xffff880000100000): depth(3496), frame_size(128), pool_size(437 kB) >>> [ 32.547921] mpt2sas_cm1: reply_dma(0x100000) >>> [ 32.548117] mpt2sas_cm1: reply_free pool(0xffff8800ba964000): depth(3496), element_size(4), pool_size(13 kB) >>> [ 32.548500] mpt2sas_cm1: reply_free_dma (0xba964000) >>> [ 32.548698] mpt2sas_cm1: config page(0xffff8800ba960000): size(512) >>> [ 32.548908] mpt2sas_cm1: config_page_dma(0xba960000) >>> [ 32.549105] mpt2sas_cm1: Allocated physical memory: size(4964 kB) >>> [ 32.549314] mpt2sas_cm1: Current Controller Queue Depth(3307),Max Controller Queue Depth(3432) >>> [ 32.550950] mpt2sas_cm1: Scatter Gather Elements per IO(128) >>> [ 32.551160] mpt2sas_cm1: _base_make_ioc_operational >>> [ 32.551855] mpt2sas_cm1: _base_send_ioc_init >>> [ 32.552051] offset:data >>> [ 32.552224] [0x00]:02000004 >>> [ 32.552400] [0x04]:00000000 >>> [ 32.552576] [0x08]:00000000 >>> [ 32.552761] [0x0c]:23000200 >>> [ 32.552937] [0x10]:00000000 >>> [ 32.553114] [0x14]:00000000 >>> [ 32.553291] [0x18]:00200000 >>> [ 32.553468] [0x1c]:0da81b20 >>> [ 32.553685] [0x20]:00000000 >>> [ 32.553862] [0x24]:00000000 >>> [ 32.554038] [0x28]:ba480000 >>> [ 32.554215] [0x2c]:00000000 >>> [ 32.554393] [0x30]:bb3d0000 >>> [ 32.554569] [0x34]:00000000 >>> [ 32.554752] [0x38]:ba964000 >>> [ 32.554929] [0x3c]:00000000 >>> [ 32.555106] [0x40]:983f2ce6 >>> [ 32.555283] [0x44]:00000153 >>> [ 32.601516] offset:data >>> [ 32.601768] [0x00]:02050004 >>> [ 32.602003] [0x04]:00000000 >>> [ 32.602239] [0x08]:00000000 >>> [ 32.602474] [0x0c]:00000000 >>> [ 32.602709] [0x10]:00000000 >>> [ 32.602945] mpt2sas_cm1: _base_event_notification >>> [ 62.593604] mpt2sas_cm1: _base_event_notification: timeout >>> [ 62.593906] mf: >>> >>> [ 62.594127] 07000000 >>> [ 62.594390] 00000000 >>> [ 62.594438] 00000000 >>> [ 62.594709] 00000000 >>> [ 62.594757] 00000000 >>> [ 62.595019] 0f2f7fff >>> [ 62.595067] ffffff7c >>> [ 62.595330] ffffffff >>> [ 62.595377] >>> >>> [ 62.595808] ffffffff >>> [ 62.595855] 00000000 >>> [ 62.596117] 00000000 >>> >>> [ 62.596601] mpt2sas_cm1: mpt3sas_base_free_resources >>> [ 62.596871] mpt2sas_cm1: _base_make_ioc_ready >>> [ 62.597125] mpt2sas_cm1: sending message unit reset !! >>> [ 62.599013] mpt2sas_cm1: message unit reset: SUCCESS >>> [ 62.599283] mpt2sas_cm1: mpt3sas_base_unmap_resources >>> [ 62.600443] mpt2sas_cm1: _base_release_memory_pools >>> [ 62.600721] mpt2sas_cm1: request_pool(0xffff8800ba480000): free >>> [ 62.601002] mpt2sas_cm1: sense_pool(0xffff8800ba880000): free >>> [ 62.601280] mpt2sas_cm1: reply_pool(0xffff880000100000): free >>> [ 62.601560] mpt2sas_cm1: reply_free_pool(0xffff8800ba964000): free >>> [ 62.601845] mpt2sas_cm1: reply_post_free_pool(0xffff8800bb3d0000): free >>> [ 62.602133] mpt2sas_cm1: config_page(0xffff8800ba960000): free >>> [ 62.673591] mpt2sas_cm1: failure at drivers/scsi/mpt3sas/mpt3sas_scsih.c:8592/_scsih_probe()! >> >> These are for two controllers, I don't know whether the output from the >> second is helpful at all - I added it anyway. >> >> >> I managed to boot the same 4.5.0 kernel successfully after warm >> rebooting from 4.1.20. That gave me this dmesg output (for comparison): >> >>> [ 2.057685] mpt3sas version 09.102.00.00 loaded >>> [ 2.058371] mpt2sas_cm0: mpt3sas_base_attach >>> [ 2.058632] mpt2sas_cm0: mpt3sas_base_map_resources >>> [ 2.059583] mpt2sas_cm0: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3074748 kB) >>> [ 2.059911] mpt2sas_cm0: _base_get_ioc_facts >>> [ 2.060166] mpt2sas_cm0: _base_wait_for_iocstate >>> [ 2.116337] offset:data >>> [ 2.116576] [0x00]:03100200 >>> [ 2.116817] [0x04]:00002300 >>> [ 2.117051] [0x08]:00000000 >>> [ 2.117285] [0x0c]:00000000 >>> [ 2.117518] [0x10]:00000000 >>> [ 2.117752] [0x14]:00010480 >>> [ 2.117986] [0x18]:22130d68 >>> [ 2.118220] [0x1c]:0001285c >>> [ 2.119624] [0x20]:14000400 >>> [ 2.119858] [0x24]:00000020 >>> [ 2.120093] [0x28]:0100000f >>> [ 2.120351] [0x2c]:000c000b >>> [ 2.120586] [0x30]:003c0003 >>> [ 2.120820] [0x34]:0020ffe0 >>> [ 2.121055] [0x38]:00800122 >>> [ 2.121288] [0x3c]:00000009 >>> [ 2.121524] mpt2sas_cm0: hba queue depth(3432), max chains per io(128) >>> [ 2.121808] mpt2sas_cm0: request frame size(128), reply frame size(128) >>> [ 2.122195] mpt2sas_cm0: msix is supported, vector_count(1) >>> [ 2.122468] mpt2sas_cm0: MSI-X vectors supported: 1, no of cores: 4, max_msix_vectors: -1 >>> [ 2.123239] mpt2sas0-msix0: PCI-MSI-X enabled: IRQ 58 >>> [ 2.123507] mpt2sas_cm0: iomem(0x00000000fd4fc000), mapped(0xffffc900000d0000), size(16384) >>> [ 2.123816] mpt2sas_cm0: ioport(0x0000000000004000), size(256) >>> [ 2.124623] mpt2sas_cm0: _base_get_ioc_facts >>> [ 2.124878] mpt2sas_cm0: _base_wait_for_iocstate >>> [ 2.180907] offset:data >>> [ 2.181145] [0x00]:03100200 >>> [ 2.181379] [0x04]:00002300 >>> [ 2.181613] [0x08]:00000000 >>> [ 2.181847] [0x0c]:00000000 >>> [ 2.182081] [0x10]:00000000 >>> [ 2.182315] [0x14]:00010480 >>> [ 2.182547] [0x18]:22130d68 >>> [ 2.182781] [0x1c]:0001285c >>> [ 2.183014] [0x20]:14000400 >>> [ 2.183248] [0x24]:00000020 >>> [ 2.183481] [0x28]:0100000f >>> [ 2.183720] [0x2c]:000c000b >>> [ 2.183954] [0x30]:003c0003 >>> [ 2.184190] [0x34]:0020ffe0 >>> [ 2.184424] [0x38]:00800122 >>> [ 2.184658] [0x3c]:00000009 >>> [ 2.184893] mpt2sas_cm0: hba queue depth(3432), max chains per io(128) >>> [ 2.185177] mpt2sas_cm0: request frame size(128), reply frame size(128) >>> [ 2.185462] mpt2sas_cm0: _base_make_ioc_ready >>> [ 2.185717] mpt2sas_cm0: _base_get_port_facts >>> [ 2.214057] offset:data >>> [ 2.214295] [0x00]:05070000 >>> [ 2.214529] [0x04]:00000000 >>> [ 2.214762] [0x08]:00000000 >>> [ 2.214997] [0x0c]:00000000 >>> [ 2.215230] [0x10]:00000000 >>> [ 2.215464] [0x14]:00003000 >>> [ 2.215697] [0x18]:00000078 >>> [ 2.215931] mpt2sas_cm0: _base_allocate_memory_pools >>> [ 2.216194] mpt2sas_cm0: scatter gather: sge_in_main_msg(3), sge_per_chain(15), sge_per_io(128), chains_per_io(9) >>> [ 2.216734] mpt2sas_cm0: reply post free pool (0xffff8800bafc0000): depth(6944),element_size(8), pool_size(54 kB) >>> [ 2.217244] mpt2sas_cm0: reply_post_free_dma = (0xbafc0000) >>> [ 2.217514] mpt2sas_cm0: scsi host: can_queue depth (3307) >>> [ 2.217866] mpt2sas_cm0: request pool(0xffff8800ba800000): depth(3432), frame_size(128), pool_size(429 kB) >>> [ 2.218369] mpt2sas_cm0: request pool: dma(0xba800000) >>> [ 2.218637] mpt2sas_cm0: scsiio(0xffff8800ba800000): depth(3307) >>> [ 2.224773] mpt2sas_cm0: chain pool depth(29763), frame_size(128), pool_size(3720 kB) >>> [ 2.225092] mpt2sas_cm0: hi_priority(0xffff8800ba867600): depth(60), start smid(3308) >>> [ 2.225395] mpt2sas_cm0: internal(0xffff8800ba869400): depth(65), start smid(3368) >>> [ 2.225958] mpt2sas_cm0: sense pool(0xffff8800ba480000): depth(3307), element_size(96), pool_size(310 kB) >>> [ 2.226457] mpt2sas_cm0: sense_dma(0xba480000) >>> [ 2.227039] mpt2sas_cm0: reply pool(0xffff8800ba500000): depth(3496), frame_size(128), pool_size(437 kB) >>> [ 2.227413] mpt2sas_cm0: reply_dma(0xba500000) >>> [ 2.227616] mpt2sas_cm0: reply_free pool(0xffff8800ba450000): depth(3496), element_size(4), pool_size(13 kB) >>> [ 2.227992] mpt2sas_cm0: reply_free_dma (0xba450000) >>> [ 2.228192] mpt2sas_cm0: config page(0xffff8800ba43b000): size(512) >>> [ 2.228402] mpt2sas_cm0: config_page_dma(0xba43b000) >>> [ 2.228598] mpt2sas_cm0: Allocated physical memory: size(4964 kB) >>> [ 2.228806] mpt2sas_cm0: Current Controller Queue Depth(3307),Max Controller Queue Depth(3432) >>> [ 2.229171] mpt2sas_cm0: Scatter Gather Elements per IO(128) >>> [ 2.229378] mpt2sas_cm0: _base_make_ioc_operational >>> [ 2.229959] mpt2sas_cm0: _base_send_ioc_init >>> [ 2.230151] offset:data >>> [ 2.230323] [0x00]:02000004 >>> [ 2.230499] [0x04]:00000000 >>> [ 2.230675] [0x08]:00000000 >>> [ 2.230851] [0x0c]:23000200 >>> [ 2.231026] [0x10]:00000000 >>> [ 2.231201] [0x14]:00000000 >>> [ 2.231376] [0x18]:00200000 >>> [ 2.231551] [0x1c]:0da81b20 >>> [ 2.231726] [0x20]:00000000 >>> [ 2.231900] [0x24]:00000000 >>> [ 2.232075] [0x28]:ba800000 >>> [ 2.232250] [0x2c]:00000000 >>> [ 2.232423] [0x30]:bafc0000 >>> [ 2.232597] [0x34]:00000000 >>> [ 2.232775] [0x38]:ba450000 >>> [ 2.232950] [0x3c]:00000000 >>> [ 2.233125] [0x40]:98596e4f >>> [ 2.233299] [0x44]:00000153 >>> [ 2.278752] offset:data >>> [ 2.278988] [0x00]:02050004 >>> [ 2.279220] [0x04]:00000000 >>> [ 2.279453] [0x08]:00000000 >>> [ 2.279685] [0x0c]:00000000 >>> [ 2.279918] [0x10]:00000000 >>> [ 2.280151] mpt2sas_cm0: _base_event_notification >>> [ 2.280537] mpt2sas_cm0: _base_event_notification: complete >>> [ 2.281694] mpt2sas_cm0: LSISAS2008: FWVersion(20.00.04.00), ChipRevision(0x03), BiosVersion(07.39.00.00) >>> [ 2.282196] mpt2sas_cm0: Protocol=( >>> [ 2.282261] Initiator >>> [ 2.282522] ,Target >>> [ 2.282567] ), >>> [ 2.282824] Capabilities=( >>> [ 2.282877] TLR >>> [ 2.283132] ,EEDP >>> [ 2.283175] ,Snapshot Buffer >>> [ 2.283444] ,Diag Trace Buffer >>> [ 2.283502] ,Task Set Full >>> [ 2.283774] ,NCQ >>> [ 2.283816] ) >>> [ 2.284350] scsi host0: Fusion MPT SAS Host >>> [ 2.299028] mpt2sas_cm0: sending port enable !! >>> [ 2.299540] mpt2sas_cm0: Discovery: (start) >>> >>> [ 2.299972] mpt2sas_cm0: SAS Enclosure Device Status Change >>> [ 2.299984] mpt2sas_cm0: discovery event: (start) >>> >>> [ 2.300554] mpt2sas_cm0: SAS Topology Change List >>> [ 2.300759] mpt2sas_cm0: Discovery: (stop) >>> >>> [ 2.301146] mpt2sas_cm0: Discovery: (start) >>> >>> [ 2.301535] mpt2sas_cm0: Discovery: (stop) >>> >>> [ 2.301927] mpt2sas_cm0: Discovery: (start) >>> >>> [ 2.302316] mpt2sas_cm0: Discovery: (stop) >>> >>> [ 2.302707] mpt2sas_cm0: Discovery: (start) >>> >>> [ 2.304908] mpt2sas_cm0: Discovery: (stop) >>> >>> [ 2.305297] mpt2sas_cm0: Discovery: (start) >>> >>> [ 2.306776] mpt2sas_cm0: Discovery: (stop) >>> >>> [ 2.307166] mpt2sas_cm0: Discovery: (start) >>> >>> [ 2.307559] mpt2sas_cm0: Discovery: (stop) >>> >>> [ 2.307948] mpt2sas_cm0: Discovery: (start) >>> >>> [ 2.308336] mpt2sas_cm0: Discovery: (stop) >>> >>> [ 2.311738] mpt2sas_cm0: host_add: handle(0x0001), sas_addr(0x500605b003683dd0), phys(8) >>> [ 2.312097] mpt2sas_cm0: enclosure status change: (enclosure add) >>> handle(0x0001), enclosure logical id(0x500605b003683dd0) number slots(0) >>> [ 2.312551] mpt2sas_cm0: sas topology change: (responding) >>> [ 2.312768] handle(0x0000), enclosure_handle(0x0001) start_phy(00), count(8) >>> [ 2.313003] phy(01), attached_handle(0x0009): target add: link rate: new(0x0a), old(0x00) >>> [ 2.313250] phy(02), attached_handle(0x000a): target add: link rate: new(0x09), old(0x00) >>> [ 2.313498] phy(03), attached_handle(0x000b): target add: link rate: new(0x09), old(0x00) >>> [ 2.313745] phy(04), attached_handle(0x000c): target add: link rate: new(0x09), old(0x00) >>> [ 2.313992] phy(05), attached_handle(0x000d): target add: link rate: new(0x09), old(0x00) >>> [ 2.314248] phy(06), attached_handle(0x000e): target add: link rate: new(0x09), old(0x00) >>> [ 2.314495] phy(07), attached_handle(0x000f): target add: link rate: new(0x09), old(0x00) >>> [ 2.314747] mpt2sas_cm0: updating handles for sas_host(0x500605b003683dd0) >>> [ 2.316041] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x0009), sas_addr(0x4433221101000000) >>> [ 2.316465] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 2) >>> [ 2.317200] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000a), sas_addr(0x4433221102000000) >>> [ 2.317669] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 1) >>> [ 2.318431] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000b), sas_addr(0x4433221103000000) >>> [ 2.318900] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 0) >>> [ 2.319366] mpt2sas_cm0: _scsih_determine_boot_device: current_boot_device(0x4433221103000000) >>> [ 2.320151] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000c), sas_addr(0x4433221104000000) >>> [ 2.321371] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 7) >>> [ 2.322137] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000d), sas_addr(0x4433221105000000) >>> [ 2.322606] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 6) >>> [ 2.323367] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000e), sas_addr(0x4433221106000000) >>> [ 2.323834] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 5) >>> [ 2.324602] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000f), sas_addr(0x4433221107000000) >>> [ 2.325071] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 4) >>> [ 2.325541] mpt2sas_cm0: discovery event: (stop) >>> >>> [ 2.326017] mpt2sas_cm0: discovery event: (start) >>> >>> [ 2.326492] mpt2sas_cm0: discovery event: (stop) >>> >>> [ 2.326975] mpt2sas_cm0: discovery event: (start) >>> >>> [ 2.327450] mpt2sas_cm0: discovery event: (stop) >>> >>> [ 2.327923] mpt2sas_cm0: discovery event: (start) >>> >>> [ 2.328396] mpt2sas_cm0: discovery event: (stop) >>> >>> [ 2.328868] mpt2sas_cm0: discovery event: (start) >>> >>> [ 2.329340] mpt2sas_cm0: discovery event: (stop) >>> >>> [ 2.329816] mpt2sas_cm0: discovery event: (start) >>> >>> [ 2.330316] mpt2sas_cm0: discovery event: (stop) >>> >>> [ 2.330797] mpt2sas_cm0: discovery event: (start) >>> >>> [ 2.331269] mpt2sas_cm0: discovery event: (stop) >>> >>> [ 2.331740] mpt2sas_cm0: port enable: complete from worker thread >>> [ 2.350236] mpt2sas_cm0: port enable: SUCCESS >>> [ 2.356432] scsi 0:0:0:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 >>> [ 2.356683] scsi 0:0:0:0: SATA: handle(0x000b), sas_addr(0x4433221103000000), phy(3), device_name(0x5000c5000267c9f8) >>> [ 2.357080] scsi 0:0:0:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(0) >>> [ 2.357405] scsi 0:0:0:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>> [ 2.383043] scsi 0:0:1:0: Direct-Access ATA Hitachi HDS5C302 A800 PQ: 0 ANSI: 6 >>> [ 2.383296] scsi 0:0:1:0: SATA: handle(0x0009), sas_addr(0x4433221101000000), phy(1), device_name(0x5000cca369cdd311) >>> [ 2.383684] scsi 0:0:1:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(2) >>> [ 2.384028] scsi 0:0:1:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>> [ 2.405088] scsi 0:0:2:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 >>> [ 2.405346] scsi 0:0:2:0: SATA: handle(0x000a), sas_addr(0x4433221102000000), phy(2), device_name(0x5000c5000ccfbd32) >>> [ 2.405735] scsi 0:0:2:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(1) >>> [ 2.406082] scsi 0:0:2:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>> [ 2.424125] scsi 0:0:3:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 >>> [ 2.424373] scsi 0:0:3:0: SATA: handle(0x000c), sas_addr(0x4433221104000000), phy(4), device_name(0x5000c5000267abee) >>> [ 2.424763] scsi 0:0:3:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(7) >>> [ 2.425108] scsi 0:0:3:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>> [ 2.444834] scsi 0:0:4:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 >>> [ 2.445086] scsi 0:0:4:0: SATA: handle(0x000d), sas_addr(0x4433221105000000), phy(5), device_name(0x5000c50009c0e5e6) >>> [ 2.445478] scsi 0:0:4:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(6) >>> [ 2.445803] scsi 0:0:4:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>> [ 2.464065] scsi 0:0:5:0: Direct-Access ATA ST3750330NS SN16 PQ: 0 ANSI: 6 >>> [ 2.464312] scsi 0:0:5:0: SATA: handle(0x000e), sas_addr(0x4433221106000000), phy(6), device_name(0x5000c5003cb9ac10) >>> [ 2.464699] scsi 0:0:5:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(5) >>> [ 2.465048] scsi 0:0:5:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>> [ 2.484016] scsi 0:0:6:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 >>> [ 2.484266] scsi 0:0:6:0: SATA: handle(0x000f), sas_addr(0x4433221107000000), phy(7), device_name(0x5000c5000839b69e) >>> [ 2.484655] scsi 0:0:6:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(4) >>> [ 2.485001] scsi 0:0:6:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>> [ 2.500660] mpt2sas_cm1: mpt3sas_base_attach >>> [ 2.500861] mpt2sas_cm1: mpt3sas_base_map_resources >>> [ 2.501599] mpt2sas_cm1: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3074748 kB) >>> [ 2.501847] mpt2sas_cm1: _base_get_ioc_facts >>> [ 2.502036] mpt2sas_cm1: _base_wait_for_iocstate >>> [ 2.559080] offset:data >>> [ 2.559318] [0x00]:03100200 >>> [ 2.559552] [0x04]:00002300 >>> [ 2.559785] [0x08]:00000000 >>> [ 2.560020] [0x0c]:00000000 >>> [ 2.560277] [0x10]:00000000 >>> [ 2.560511] [0x14]:00010480 >>> [ 2.560745] [0x18]:22130d68 >>> [ 2.560978] [0x1c]:0001285c >>> [ 2.561210] [0x20]:14000400 >>> [ 2.561443] [0x24]:00000020 >>> [ 2.561675] [0x28]:0100000f >>> [ 2.561907] [0x2c]:000c000b >>> [ 2.562139] [0x30]:003c0003 >>> [ 2.562371] [0x34]:0020ffe0 >>> [ 2.562602] [0x38]:00800122 >>> [ 2.562839] [0x3c]:00000009 >>> [ 2.563073] mpt2sas_cm1: hba queue depth(3432), max chains per io(128) >>> [ 2.563355] mpt2sas_cm1: request frame size(128), reply frame size(128) >>> [ 2.563745] mpt2sas_cm1: msix is supported, vector_count(1) >>> [ 2.564016] mpt2sas_cm1: MSI-X vectors supported: 1, no of cores: 4, max_msix_vectors: 8 >>> [ 2.564918] mpt2sas1-msix0: PCI-MSI-X enabled: IRQ 59 >>> [ 2.566189] mpt2sas_cm1: iomem(0x00000000fd1fc000), mapped(0xffffc900000d8000), size(16384) >>> [ 2.566498] mpt2sas_cm1: ioport(0x0000000000007000), size(256) >>> [ 2.567328] mpt2sas_cm1: _base_get_ioc_facts >>> [ 2.567583] mpt2sas_cm1: _base_wait_for_iocstate >>> [ 2.625125] offset:data >>> [ 2.625364] [0x00]:03100200 >>> [ 2.625597] [0x04]:00002300 >>> [ 2.625830] [0x08]:00000000 >>> [ 2.626064] [0x0c]:00000000 >>> [ 2.626296] [0x10]:00000000 >>> [ 2.626529] [0x14]:00010480 >>> [ 2.626769] [0x18]:22130d68 >>> [ 2.627002] [0x1c]:0001285c >>> [ 2.627235] [0x20]:14000400 >>> [ 2.627467] [0x24]:00000020 >>> [ 2.627702] [0x28]:0100000f >>> [ 2.627936] [0x2c]:000c000b >>> [ 2.628170] [0x30]:003c0003 >>> [ 2.628403] [0x34]:0020ffe0 >>> [ 2.628638] [0x38]:00800122 >>> [ 2.628872] [0x3c]:00000009 >>> [ 2.629107] mpt2sas_cm1: hba queue depth(3432), max chains per io(128) >>> [ 2.629388] mpt2sas_cm1: request frame size(128), reply frame size(128) >>> [ 2.629671] mpt2sas_cm1: _base_make_ioc_ready >>> [ 2.629928] mpt2sas_cm1: _base_get_port_facts >>> [ 2.660127] offset:data >>> [ 2.660389] [0x00]:05070000 >>> [ 2.660623] [0x04]:00000000 >>> [ 2.660858] [0x08]:00000000 >>> [ 2.661093] [0x0c]:00000000 >>> [ 2.661326] [0x10]:00000000 >>> [ 2.661562] [0x14]:00003000 >>> [ 2.661796] [0x18]:00000078 >>> [ 2.664346] mpt2sas_cm1: _base_allocate_memory_pools >>> [ 2.664608] mpt2sas_cm1: scatter gather: sge_in_main_msg(3), sge_per_chain(15), sge_per_io(128), chains_per_io(9) >>> [ 2.665142] mpt2sas_cm1: reply post free pool (0xffff8800b8b10000): depth(6944),element_size(8), pool_size(54 kB) >>> [ 2.666671] mpt2sas_cm1: reply_post_free_dma = (0xb8b10000) >>> [ 2.666954] mpt2sas_cm1: scsi host: can_queue depth (3307) >>> [ 2.667311] mpt2sas_cm1: request pool(0xffff8800b8b80000): depth(3432), frame_size(128), pool_size(429 kB) >>> [ 2.667813] mpt2sas_cm1: request pool: dma(0xb8b80000) >>> [ 2.668080] mpt2sas_cm1: scsiio(0xffff8800b8b80000): depth(3307) >>> [ 2.674131] mpt2sas_cm1: chain pool depth(29763), frame_size(128), pool_size(3720 kB) >>> [ 2.674448] mpt2sas_cm1: hi_priority(0xffff8800b8be7600): depth(60), start smid(3308) >>> [ 2.674750] mpt2sas_cm1: internal(0xffff8800b8be9400): depth(65), start smid(3368) >>> [ 2.675105] mpt2sas_cm1: sense pool(0xffff8800b8100000): depth(3307), element_size(96), pool_size(310 kB) >>> [ 2.675605] mpt2sas_cm1: sense_dma(0xb8100000) >>> [ 2.675944] mpt2sas_cm1: reply pool(0xffff8800b8180000): depth(3496), frame_size(128), pool_size(437 kB) >>> [ 2.676443] mpt2sas_cm1: reply_dma(0xb8180000) >>> [ 2.676702] mpt2sas_cm1: reply_free pool(0xffff8800b80a0000): depth(3496), element_size(4), pool_size(13 kB) >>> [ 2.677124] mpt2sas_cm1: reply_free_dma (0xb80a0000) >>> [ 2.677322] mpt2sas_cm1: config page(0xffff8800b807f000): size(512) >>> [ 2.677532] mpt2sas_cm1: config_page_dma(0xb807f000) >>> [ 2.677728] mpt2sas_cm1: Allocated physical memory: size(4964 kB) >>> [ 2.677936] mpt2sas_cm1: Current Controller Queue Depth(3307),Max Controller Queue Depth(3432) >>> [ 2.678304] mpt2sas_cm1: Scatter Gather Elements per IO(128) >>> [ 2.678514] mpt2sas_cm1: _base_make_ioc_operational >>> [ 2.679081] mpt2sas_cm1: _base_send_ioc_init >>> [ 2.679275] offset:data >>> [ 2.679448] [0x00]:02000004 >>> [ 2.679625] [0x04]:00000000 >>> [ 2.679805] [0x08]:00000000 >>> [ 2.681200] [0x0c]:23000200 >>> [ 2.681377] [0x10]:00000000 >>> [ 2.681554] [0x14]:00000000 >>> [ 2.681729] [0x18]:00200000 >>> [ 2.681906] [0x1c]:0da81b20 >>> [ 2.682082] [0x20]:00000000 >>> [ 2.682259] [0x24]:00000000 >>> [ 2.682435] [0x28]:b8b80000 >>> [ 2.682611] [0x2c]:00000000 >>> [ 2.682787] [0x30]:b8b10000 >>> [ 2.682963] [0x34]:00000000 >>> [ 2.683139] [0x38]:b80a0000 >>> [ 2.683314] [0x3c]:00000000 >>> [ 2.683489] [0x40]:98597011 >>> [ 2.683665] [0x44]:00000153 >>> [ 2.729849] offset:data >>> [ 2.730089] [0x00]:02050004 >>> [ 2.730349] [0x04]:00000000 >>> [ 2.730586] [0x08]:00000000 >>> [ 2.730822] [0x0c]:00000000 >>> [ 2.731058] [0x10]:00000000 >>> [ 2.731295] mpt2sas_cm1: _base_event_notification >>> [ 2.731606] mpt2sas_cm1: _base_event_notification: complete >>> [ 2.732501] mpt2sas_cm1: LSISAS2008: FWVersion(20.00.04.00), ChipRevision(0x02), BiosVersion(07.39.00.00) >>> [ 2.733010] mpt2sas_cm1: Protocol=( >>> [ 2.733074] Initiator >>> [ 2.733339] ,Target >>> [ 2.733384] ), >>> [ 2.733642] Capabilities=( >>> [ 2.733696] TLR >>> [ 2.733952] ,EEDP >>> [ 2.733995] ,Snapshot Buffer >>> [ 2.734268] ,Diag Trace Buffer >>> [ 2.734326] ,Task Set Full >>> [ 2.734595] ,NCQ >>> [ 2.734637] ) >>> [ 2.735155] scsi host1: Fusion MPT SAS Host >>> [ 2.749047] mpt2sas_cm1: sending port enable !! >>> [ 2.749563] mpt2sas_cm1: Discovery: (start) >>> >>> [ 2.749989] mpt2sas_cm1: SAS Enclosure Device Status Change >>> [ 2.750001] mpt2sas_cm1: discovery event: (start) >>> >>> [ 2.750578] mpt2sas_cm1: SAS Topology Change List >>> [ 2.750788] mpt2sas_cm1: Discovery: (stop) >>> >>> [ 2.751181] mpt2sas_cm1: Discovery: (start) >>> >>> [ 2.751571] mpt2sas_cm1: Discovery: (stop) >>> >>> [ 2.752002] mpt2sas_cm1: Discovery: (start) >>> >>> [ 2.752391] mpt2sas_cm1: Discovery: (stop) >>> >>> [ 2.752779] mpt2sas_cm1: Discovery: (start) >>> >>> [ 2.754205] mpt2sas_cm1: Discovery: (stop) >>> >>> [ 2.754593] mpt2sas_cm1: Discovery: (start) >>> >>> [ 2.754983] mpt2sas_cm1: Discovery: (stop) >>> >>> [ 2.755371] mpt2sas_cm1: Discovery: (start) >>> >>> [ 2.755762] mpt2sas_cm1: Discovery: (stop) >>> >>> [ 2.759602] mpt2sas_cm1: host_add: handle(0x0001), sas_addr(0x500605b0026f79b0), phys(8) >>> [ 2.759969] mpt2sas_cm1: enclosure status change: (enclosure add) >>> handle(0x0001), enclosure logical id(0x500605b0026f79b0) number slots(0) >>> [ 2.760407] mpt2sas_cm1: sas topology change: (responding) >>> [ 2.760612] handle(0x0000), enclosure_handle(0x0001) start_phy(00), count(8) >>> [ 2.760834] phy(02), attached_handle(0x000e): target add: link rate: new(0x0a), old(0x00) >>> [ 2.761066] phy(03), attached_handle(0x000b): target add: link rate: new(0x0a), old(0x00) >>> [ 2.761304] phy(04), attached_handle(0x000d): target add: link rate: new(0x09), old(0x00) >>> [ 2.761538] phy(05), attached_handle(0x0009): target add: link rate: new(0x09), old(0x00) >>> [ 2.761771] phy(06), attached_handle(0x000a): target add: link rate: new(0x09), old(0x00) >>> [ 2.762002] phy(07), attached_handle(0x000c): target add: link rate: new(0x09), old(0x00) >>> [ 2.762235] mpt2sas_cm1: updating handles for sas_host(0x500605b0026f79b0) >>> [ 2.763653] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x000e), sas_addr(0x4433221102000000) >>> [ 2.764036] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 1) >>> [ 2.764772] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x000b), sas_addr(0x4433221103000000) >>> [ 2.765147] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 0) >>> [ 2.765891] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x000d), sas_addr(0x4433221104000000) >>> [ 2.767250] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 7) >>> [ 2.768009] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x0009), sas_addr(0x4433221105000000) >>> [ 2.768394] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 6) >>> [ 2.769136] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x000a), sas_addr(0x4433221106000000) >>> [ 2.769510] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 5) >>> [ 2.769888] mpt2sas_cm1: _scsih_determine_boot_device: current_boot_device(0x4433221106000000) >>> [ 2.770641] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x000c), sas_addr(0x4433221107000000) >>> [ 2.771025] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 4) >>> [ 2.771405] mpt2sas_cm1: discovery event: (stop) >>> >>> [ 2.771788] mpt2sas_cm1: discovery event: (start) >>> >>> [ 2.772172] mpt2sas_cm1: discovery event: (stop) >>> >>> [ 2.772554] mpt2sas_cm1: discovery event: (start) >>> >>> [ 2.772942] mpt2sas_cm1: discovery event: (stop) >>> >>> [ 2.773326] mpt2sas_cm1: discovery event: (start) >>> >>> [ 2.773709] mpt2sas_cm1: discovery event: (stop) >>> >>> [ 2.774090] mpt2sas_cm1: discovery event: (start) >>> >>> [ 2.774474] mpt2sas_cm1: discovery event: (stop) >>> >>> [ 2.774855] mpt2sas_cm1: discovery event: (start) >>> >>> [ 2.775237] mpt2sas_cm1: discovery event: (stop) >>> >>> [ 2.775619] mpt2sas_cm1: port enable: complete from worker thread >>> [ 2.780192] mpt2sas_cm1: port enable: SUCCESS >>> [ 2.782404] scsi 1:0:0:0: Direct-Access ATA Hitachi HDP72505 A5BA PQ: 0 ANSI: 6 >>> [ 2.782651] scsi 1:0:0:0: SATA: handle(0x000a), sas_addr(0x4433221106000000), phy(6), device_name(0x5000cca34dc05584) >>> [ 2.783039] scsi 1:0:0:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(5) >>> [ 2.783390] scsi 1:0:0:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>> [ 2.803032] scsi 1:0:1:0: Direct-Access ATA ST8000AS0002-1NA AR15 PQ: 0 ANSI: 6 >>> [ 2.803272] scsi 1:0:1:0: SATA: handle(0x000e), sas_addr(0x4433221102000000), phy(2), device_name(0x5000c500908f1d05) >>> [ 2.803660] scsi 1:0:1:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(1) >>> [ 2.803981] scsi 1:0:1:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>> [ 2.821712] scsi 1:0:2:0: Direct-Access ATA ST3000DM001-1CH1 CC43 PQ: 0 ANSI: 6 >>> [ 2.821963] scsi 1:0:2:0: SATA: handle(0x000b), sas_addr(0x4433221103000000), phy(3), device_name(0x5000c5004dfd2a8a) >>> [ 2.822352] scsi 1:0:2:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(0) >>> [ 2.822694] scsi 1:0:2:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>> [ 2.844233] scsi 1:0:3:0: Direct-Access ATA ST3500320NS SN16 PQ: 0 ANSI: 6 >>> [ 2.844483] scsi 1:0:3:0: SATA: handle(0x000d), sas_addr(0x4433221104000000), phy(4), device_name(0x5000c50009dca65b) >>> [ 2.844870] scsi 1:0:3:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(7) >>> [ 2.845216] scsi 1:0:3:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>> [ 2.868963] scsi 1:0:4:0: Direct-Access ATA SAMSUNG HD401LJ 0-15 PQ: 0 ANSI: 6 >>> [ 2.870994] scsi 1:0:4:0: SATA: handle(0x0009), sas_addr(0x4433221105000000), phy(5), device_name(0x695d550daf678093) >>> [ 2.871382] scsi 1:0:4:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(6) >>> [ 2.871728] scsi 1:0:4:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>> [ 2.894004] scsi 1:0:5:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 >>> [ 2.894257] scsi 1:0:5:0: SATA: handle(0x000c), sas_addr(0x4433221107000000), phy(7), device_name(0x5000c5000266bb02) >>> [ 2.894646] scsi 1:0:5:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(4) >>> [ 2.894972] scsi 1:0:5:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >> >> I don't see a clear pattern yet, but I suspect warm rebooting >=4.2 >> after having run 4.1.x leads to sucessful driver inits. But I also >> remember having had cold boots, with kernels >=4.2 that worked fine >> (obviously not all of the time). <=4.1.20 kernels on the other hand boot >> fine every single time. >> >> Interestingly the igb driver (ethernet) seems to be acting up at least >> with 4.5.0 on exactly the same boots when mpt2sas init fails. I don't >> know whether this could be connected or not (I just became aware of this >> coincidence). >> >> >> --- >> Matthias >> >> >> Am 21.03.2016 um 05:53 schrieb Sreekanth Reddy: >>> Hi Matthias, >>> >>> Can you please share us the driver logs with driver logging_level set >>> to 0x3f8. So that we can get more info from this log. >>> >>> Thanks, >>> Sreekanth >>> >>> On Mon, Mar 21, 2016 at 1:44 AM, Matthias Prager >>> <linux@matthiasprager.de> wrote: >>>> Hello, >>>> >>>> I don't know what's the correct procedure, whether I should file a bug or first report this issue on the kernel mailing-list. So please feel free to tell me to open a ticket in the bugtracker (bugzilla.kernel.org?). >>>> >>>> But first let me present the issue I encounter: >>>> >>>> Kernels >= 4.2 (4.2.1 was the first on I tried, but also 4.3, 4.4 and 4.5) fail to load the mpt2sas driver on most (but not all) boots. Kernels <= 4.1.x work fine every single time (4.1.19 was the latest I tried, also 3.18.29). >>>> >>>> Here is the dmesg output for a failed driver init with Kernel 4.5.0: >>>>> [ 2.068313] mpt3sas version 09.102.00.00 loaded >>>>> [ 2.069412] mpt2sas_cm0: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3074748 kB) >>>>> [ 2.125260] mpt2sas_cm0: MSI-X vectors supported: 1, no of cores: 4, max_msix_vectors: -1 >>>>> [ 2.125996] mpt2sas0-msix0: PCI-MSI-X enabled: IRQ 58 >>>>> [ 2.126199] mpt2sas_cm0: iomem(0x00000000fd4fc000), mapped(0xffffc900000d0000), size(16384) >>>>> [ 2.126430] mpt2sas_cm0: ioport(0x0000000000004000), size(256) >>>>> [ 2.216371] mpt2sas_cm0: Allocated physical memory: size(4964 kB) >>>>> [ 2.216600] mpt2sas_cm0: Current Controller Queue Depth(3307),Max Controller Queue Depth(3432) >>>>> [ 2.217004] mpt2sas_cm0: Scatter Gather Elements per IO(128) >>>>> [ 5.086959] floppy0: no floppy controllers found >>>>> [ 32.256720] mpt2sas_cm0: _base_event_notification: timeout >>>>> [ 32.256940] mf: >>>>> >>>>> [ 32.257106] 07000000 >>>>> [ 32.257302] 00000000 >>>>> [ 32.257337] 00000000 >>>>> [ 32.257533] 00000000 >>>>> [ 32.257568] 00000000 >>>>> [ 32.257764] 0f2f7fff >>>>> [ 32.257800] ffffff7c >>>>> [ 32.257995] ffffffff >>>>> [ 32.258031] >>>>> >>>>> [ 32.258352] ffffffff >>>>> [ 32.258387] 00000000 >>>>> [ 32.258582] 00000000 >>>>> >>>>> [ 32.258950] mpt2sas_cm0: sending message unit reset !! >>>>> [ 32.260688] mpt2sas_cm0: message unit reset: SUCCESS >>>>> [ 32.325956] mpt2sas_cm0: failure at drivers/scsi/mpt3sas/mpt3sas_scsih.c:8592/_scsih_probe()! >>>> >>>> For comparison here is a dmesg output for a successful boot on Kernel 4.1.15: >>>>> [ 2.035568] mpt2sas version 20.100.00.00 loaded >>>>> [ 2.037243] mpt2sas0: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (2046352 kB) >>>>> [ 2.755374] mpt2sas0: MSI-X vectors supported: 1, no of cores: 3, max_msix_vectors: 8 >>>>> [ 2.756377] mpt2sas0-msix0: PCI-MSI-X enabled: IRQ 58 >>>>> [ 2.756708] mpt2sas0: iomem(0x00000000fd5fc000), mapped(0xffffc900000d0000), size(16384) >>>>> [ 2.757083] mpt2sas0: ioport(0x0000000000004000), size(256) >>>>> [ 3.842944] mpt2sas0: Allocated physical memory: size(4964 kB) >>>>> [ 3.843303] mpt2sas0: Current Controller Queue Depth(3307), Max Controller Queue Depth(3432) >>>>> [ 3.843717] mpt2sas0: Scatter Gather Elements per IO(128) >>>>> [ 4.415980] mpt2sas0: LSISAS2008: FWVersion(20.00.04.00), ChipRevision(0x03), BiosVersion(07.39.00.00) >>>>> [ 4.416618] mpt2sas0: Protocol=(Initiator,Target), Capabilities=(TLR,EEDP,Snapshot Buffer,Diag Trace Buffer,Task Set Full,NCQ) >>>>> [ 4.417846] scsi host0: Fusion MPT SAS Host >>>>> [ 4.436865] mpt2sas0: sending port enable !! >>>>> [ 4.440460] mpt2sas0: host_add: handle(0x0001), sas_addr(0xxxxxxxxxxxxxxxxx), phys(8) >>>>> >>>>> ... >>>>> [ 4.444045] scsi 0:0:0:0: Direct-Access ATA Hitachi HDS5C302 A800 PQ: 0 ANSI: 6 >>>>> [ 4.444338] scsi 0:0:0:0: SATA: handle(0x0009), sas_addr(0xxxxxxxxxxxxxxxxx), phy(1), device_name(0xxxxxxxxxxxxxxxxx) >>>>> [ 4.444823] scsi 0:0:0:0: SATA: enclosure_logical_id(0xxxxxxxxxxxxxxxxx), slot(2) >>>>> [ 4.445197] scsi 0:0:0:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>> ... (n times for n drives) >>>>> >>>>> [ 4.515443] mpt2sas0: port enable: SUCCESS >>>> >>>> >>>> The Controller(s) are all Avego/LSI 9211-8i running the latest version of IT firmware (v20.00.04.00). These are passed through to a gentoo-linux VM on an ESXi 5.1 host (latest patchlevel). I have two of these systems (one production one testing) with nearly identical hardware (Supermicro X8DTi-F boards with 2x Intel Westmere CPUs). I also have an older set of systems running the same software config (Intel S3200SHLC boards with single Core2Quad) which exhibit the same buggy behavior. >>>> >>>> The 'uname -a' line on the current testing system looks like this: >>>>> Linux pserver2 4.1.19-gentoo #4 SMP Thu Mar 17 16:02:48 CET 2016 x86_64 Intel(R) Xeon(R) CPU E5506 @ 2.13GHz GenuineIntel GNU/Linux >>>> p >>>> >>>> There seem to be other people with similar issues: >>>> <https://bbs.archlinux.org/viewtopic.php?id=209495> >>>> >>>> Any thoughts? >>>> >>>> --- >>>> Matthias >> ^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [BUG] mpt2sas: driver init fails on kernel >=4.2 for 9211-8i IT 2016-03-21 15:52 ` Matthias Prager @ 2016-03-21 16:30 ` Matthias Prager 2016-03-22 10:52 ` Sreekanth Reddy 0 siblings, 1 reply; 13+ messages in thread From: Matthias Prager @ 2016-03-21 16:30 UTC (permalink / raw) To: Sreekanth Reddy; +Cc: linux-scsi, Matthias Prager Am 21.03.2016 um 16:52 schrieb Matthias Prager: > Hi Sreekanth, > > thanks for digging into this issue. Regarding the 4.5.0 after 4.1.20 > boot statement, I will try to express myself better: > > I first started the system with the 4.1.20 kernel. Then I issued an > 'init 6' warm-reboot and chose to boot the 4.5.0 kernel. This procedure > often works (i.e. I'm able to boot the newer kernels (>=4.2) this way > with mpt2sas initializing just fine). One small addition: warm-rebooting kernel 4.5.0 from kernel 4.5.0 reliably leads to this issue manifesting (mpt2sas driver not initializing). > > I will try the msix_disable parameter and report back. Maybe kernel > version 4.2 broke interrupt handling somehow? With the msix_disable parameter set kernels 4.5.0, 4.4.5, 4.3.3 and 4.2.1 boot without the mpt2sas init issue. I also tried the pci=nomsi paremeter instead, which also works fine. The igb ethernet-driver issue I mentioned as possibly related has not changed with pci=nomsi. So I'm assuming it is not the same issue, but possibly related, since it also occurs on kernels >=4.2. > > --- > Matthias > > > Am 21.03.2016 um 14:59 schrieb Sreekanth Reddy: >> Hi Matthias, >> >> Thanks for providing the logs. In these logs, I am not observing any >> such a prints which should be suspected for this issue. >> >> Can you please try once by setting mpt3sas driver's "msix_disable" >> module parameter to one. >> >> Also, can you please elaborate below statement for me, I am not able >> understand this statement >> "I managed to boot the same 4.5.0 kernel successfully after warm >> rebooting from 4.1.20" >> >> Thanks, >> Sreekanth >> >> On Mon, Mar 21, 2016 at 2:48 PM, Matthias Prager >> <linux@matthiasprager.de> wrote: >>> Hi Sreekanth, >>> >>> thank you for replying so quickly. Here are the logs you requested >>> (kernel 4.5.0): >>> >>>> [ 2.083177] mpt3sas version 09.102.00.00 loaded >>>> [ 2.083757] mpt2sas_cm0: mpt3sas_base_attach >>>> [ 2.083956] mpt2sas_cm0: mpt3sas_base_map_resources >>>> [ 2.084708] mpt2sas_cm0: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3074748 kB) >>>> [ 2.084964] mpt2sas_cm0: _base_get_ioc_facts >>>> [ 2.085154] mpt2sas_cm0: _base_wait_for_iocstate >>>> [ 2.140893] offset:data >>>> [ 2.141082] [0x00]:03100200 >>>> [ 2.141257] [0x04]:00002300 >>>> [ 2.141432] [0x08]:00000000 >>>> [ 2.141606] [0x0c]:00000000 >>>> [ 2.141780] [0x10]:00000000 >>>> [ 2.141955] [0x14]:00010480 >>>> [ 2.142129] [0x18]:22130d68 >>>> [ 2.142303] [0x1c]:0001285c >>>> [ 2.142477] [0x20]:14000400 >>>> [ 2.142651] [0x24]:00000020 >>>> [ 2.142825] [0x28]:0100000f >>>> [ 2.143000] [0x2c]:000c000b >>>> [ 2.143174] [0x30]:003c0003 >>>> [ 2.143349] [0x34]:0020ffe0 >>>> [ 2.143544] [0x38]:00800122 >>>> [ 2.143719] [0x3c]:00000009 >>>> [ 2.143895] mpt2sas_cm0: hba queue depth(3432), max chains per io(128) >>>> [ 2.144106] mpt2sas_cm0: request frame size(128), reply frame size(128) >>>> [ 2.144397] mpt2sas_cm0: msix is supported, vector_count(1) >>>> [ 2.144600] mpt2sas_cm0: MSI-X vectors supported: 1, no of cores: 4, max_msix_vectors: -1 >>>> [ 2.145161] mpt2sas0-msix0: PCI-MSI-X enabled: IRQ 58 >>>> [ 2.145361] mpt2sas_cm0: iomem(0x00000000fd4fc000), mapped(0xffffc900000d0000), size(16384) >>>> [ 2.145591] mpt2sas_cm0: ioport(0x0000000000004000), size(256) >>>> [ 2.146206] mpt2sas_cm0: _base_get_ioc_facts >>>> [ 2.146397] mpt2sas_cm0: _base_wait_for_iocstate >>>> [ 2.202087] offset:data >>>> [ 2.202281] [0x00]:03100200 >>>> [ 2.202456] [0x04]:00002300 >>>> [ 2.202631] [0x08]:00000000 >>>> [ 2.202805] [0x0c]:00000000 >>>> [ 2.202980] [0x10]:00000000 >>>> [ 2.203154] [0x14]:00010480 >>>> [ 2.203328] [0x18]:22130d68 >>>> [ 2.203521] [0x1c]:0001285c >>>> [ 2.203695] [0x20]:14000400 >>>> [ 2.203870] [0x24]:00000020 >>>> [ 2.204044] [0x28]:0100000f >>>> [ 2.204219] [0x2c]:000c000b >>>> [ 2.204394] [0x30]:003c0003 >>>> [ 2.204571] [0x34]:0020ffe0 >>>> [ 2.204746] [0x38]:00800122 >>>> [ 2.204926] [0x3c]:00000009 >>>> [ 2.205102] mpt2sas_cm0: hba queue depth(3432), max chains per io(128) >>>> [ 2.205314] mpt2sas_cm0: request frame size(128), reply frame size(128) >>>> [ 2.205528] mpt2sas_cm0: _base_make_ioc_ready >>>> [ 2.205719] mpt2sas_cm0: _base_get_port_facts >>>> [ 2.234205] offset:data >>>> [ 2.234397] [0x00]:05070000 >>>> [ 2.234573] [0x04]:00000000 >>>> [ 2.234748] [0x08]:00000000 >>>> [ 2.234928] [0x0c]:00000000 >>>> [ 2.235103] [0x10]:00000000 >>>> [ 2.235278] [0x14]:00003000 >>>> [ 2.235453] [0x18]:00000078 >>>> [ 2.235629] mpt2sas_cm0: _base_allocate_memory_pools >>>> [ 2.235826] mpt2sas_cm0: scatter gather: sge_in_main_msg(3), sge_per_chain(15), sge_per_io(128), chains_per_io(9) >>>> [ 2.236227] mpt2sas_cm0: reply post free pool (0xffff8800bb380000): depth(6944),element_size(8), pool_size(54 kB) >>>> [ 2.236611] mpt2sas_cm0: reply_post_free_dma = (0xbb380000) >>>> [ 2.236813] mpt2sas_cm0: scsi host: can_queue depth (3307) >>>> [ 2.237086] mpt2sas_cm0: request pool(0xffff8800ba880000): depth(3432), frame_size(128), pool_size(429 kB) >>>> [ 2.238580] mpt2sas_cm0: request pool: dma(0xba880000) >>>> [ 2.238781] mpt2sas_cm0: scsiio(0xffff8800ba880000): depth(3307) >>>> [ 2.243644] mpt2sas_cm0: chain pool depth(29763), frame_size(128), pool_size(3720 kB) >>>> [ 2.243887] mpt2sas_cm0: hi_priority(0xffff8800ba8e7600): depth(60), start smid(3308) >>>> [ 2.244113] mpt2sas_cm0: internal(0xffff8800ba8e9400): depth(65), start smid(3368) >>>> [ 2.244390] mpt2sas_cm0: sense pool(0xffff8800ba480000): depth(3307), element_size(96), pool_size(310 kB) >>>> [ 2.244774] mpt2sas_cm0: sense_dma(0xba480000) >>>> [ 2.245038] mpt2sas_cm0: reply pool(0xffff8800ba500000): depth(3496), frame_size(128), pool_size(437 kB) >>>> [ 2.245413] mpt2sas_cm0: reply_dma(0xba500000) >>>> [ 2.245608] mpt2sas_cm0: reply_free pool(0xffff8800ba430000): depth(3496), element_size(4), pool_size(13 kB) >>>> [ 2.245985] mpt2sas_cm0: reply_free_dma (0xba430000) >>>> [ 2.246181] mpt2sas_cm0: config page(0xffff8800ba429000): size(512) >>>> [ 2.246389] mpt2sas_cm0: config_page_dma(0xba429000) >>>> [ 2.246584] mpt2sas_cm0: Allocated physical memory: size(4964 kB) >>>> [ 2.246791] mpt2sas_cm0: Current Controller Queue Depth(3307),Max Controller Queue Depth(3432) >>>> [ 2.247155] mpt2sas_cm0: Scatter Gather Elements per IO(128) >>>> [ 2.247361] mpt2sas_cm0: _base_make_ioc_operational >>>> [ 2.247962] mpt2sas_cm0: _base_send_ioc_init >>>> [ 2.248154] offset:data >>>> [ 2.248325] [0x00]:02000004 >>>> [ 2.248499] [0x04]:00000000 >>>> [ 2.248673] [0x08]:00000000 >>>> [ 2.248848] [0x0c]:23000200 >>>> [ 2.249023] [0x10]:00000000 >>>> [ 2.249197] [0x14]:00000000 >>>> [ 2.249372] [0x18]:00200000 >>>> [ 2.249546] [0x1c]:0da81b20 >>>> [ 2.249720] [0x20]:00000000 >>>> [ 2.249894] [0x24]:00000000 >>>> [ 2.250068] [0x28]:ba880000 >>>> [ 2.250242] [0x2c]:00000000 >>>> [ 2.250416] [0x30]:bb380000 >>>> [ 2.250589] [0x34]:00000000 >>>> [ 2.250768] [0x38]:ba430000 >>>> [ 2.250941] [0x3c]:00000000 >>>> [ 2.251115] [0x40]:983eb686 >>>> [ 2.251288] [0x44]:00000153 >>>> [ 2.296610] offset:data >>>> [ 2.296795] [0x00]:02050004 >>>> [ 2.296969] [0x04]:00000000 >>>> [ 2.297143] [0x08]:00000000 >>>> [ 2.297318] [0x0c]:00000000 >>>> [ 2.297493] [0x10]:00000000 >>>> [ 2.297668] mpt2sas_cm0: _base_event_notification >>>> [ 5.093707] floppy0: no floppy controllers found >>>> [ 32.293619] mpt2sas_cm0: _base_event_notification: timeout >>>> [ 32.293909] mf: >>>> >>>> [ 32.294132] 07000000 >>>> [ 32.294397] 00000000 >>>> [ 32.294445] 00000000 >>>> [ 32.294719] 00000000 >>>> [ 32.294767] 00000000 >>>> [ 32.295031] 0f2f7fff >>>> [ 32.295078] ffffff7c >>>> [ 32.295342] ffffffff >>>> [ 32.295389] >>>> >>>> [ 32.295823] ffffffff >>>> [ 32.295871] 00000000 >>>> [ 32.296134] 00000000 >>>> >>>> [ 32.296615] mpt2sas_cm0: mpt3sas_base_free_resources >>>> [ 32.296880] mpt2sas_cm0: _base_make_ioc_ready >>>> [ 32.297135] mpt2sas_cm0: sending message unit reset !! >>>> [ 32.298941] mpt2sas_cm0: message unit reset: SUCCESS >>>> [ 32.299212] mpt2sas_cm0: mpt3sas_base_unmap_resources >>>> [ 32.300381] mpt2sas_cm0: _base_release_memory_pools >>>> [ 32.300654] mpt2sas_cm0: request_pool(0xffff8800ba880000): free >>>> [ 32.300934] mpt2sas_cm0: sense_pool(0xffff8800ba480000): free >>>> [ 32.301211] mpt2sas_cm0: reply_pool(0xffff8800ba500000): free >>>> [ 32.301485] mpt2sas_cm0: reply_free_pool(0xffff8800ba430000): free >>>> [ 32.301774] mpt2sas_cm0: reply_post_free_pool(0xffff8800bb380000): free >>>> [ 32.302061] mpt2sas_cm0: config_page(0xffff8800ba429000): free >>>> [ 32.371097] mpt2sas_cm0: failure at drivers/scsi/mpt3sas/mpt3sas_scsih.c:8592/_scsih_probe()! >>>> [ 32.371958] mpt2sas_cm1: mpt3sas_base_attach >>>> [ 32.372154] mpt2sas_cm1: mpt3sas_base_map_resources >>>> [ 32.372950] mpt2sas_cm1: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3074748 kB) >>>> [ 32.373201] mpt2sas_cm1: _base_get_ioc_facts >>>> [ 32.375261] mpt2sas_cm1: _base_wait_for_iocstate >>>> [ 32.432012] offset:data >>>> [ 32.432262] [0x00]:03100200 >>>> [ 32.432499] [0x04]:00002300 >>>> [ 32.432735] [0x08]:00000000 >>>> [ 32.432971] [0x0c]:00000000 >>>> [ 32.433206] [0x10]:00000000 >>>> [ 32.433443] [0x14]:00010480 >>>> [ 32.433701] [0x18]:22130d68 >>>> [ 32.433937] [0x1c]:0001285c >>>> [ 32.435434] [0x20]:14000400 >>>> [ 32.435674] [0x24]:00000020 >>>> [ 32.435909] [0x28]:0100000f >>>> [ 32.436144] [0x2c]:000c000b >>>> [ 32.436379] [0x30]:003c0003 >>>> [ 32.436615] [0x34]:0020ffe0 >>>> [ 32.436850] [0x38]:00800122 >>>> [ 32.437085] [0x3c]:00000009 >>>> [ 32.437322] mpt2sas_cm1: hba queue depth(3432), max chains per io(128) >>>> [ 32.437607] mpt2sas_cm1: request frame size(128), reply frame size(128) >>>> [ 32.438014] mpt2sas_cm1: msix is supported, vector_count(1) >>>> [ 32.438288] mpt2sas_cm1: MSI-X vectors supported: 1, no of cores: 4, max_msix_vectors: 8 >>>> [ 32.439101] mpt2sas1-msix0: PCI-MSI-X enabled: IRQ 58 >>>> [ 32.439373] mpt2sas_cm1: iomem(0x00000000fd1fc000), mapped(0xffffc900000d8000), size(16384) >>>> [ 32.439682] mpt2sas_cm1: ioport(0x0000000000007000), size(256) >>>> [ 32.440504] mpt2sas_cm1: _base_get_ioc_facts >>>> [ 32.440765] mpt2sas_cm1: _base_wait_for_iocstate >>>> [ 32.499305] offset:data >>>> [ 32.499557] [0x00]:03100200 >>>> [ 32.499794] [0x04]:00002300 >>>> [ 32.500031] [0x08]:00000000 >>>> [ 32.500267] [0x0c]:00000000 >>>> [ 32.500504] [0x10]:00000000 >>>> [ 32.500740] [0x14]:00010480 >>>> [ 32.500974] [0x18]:22130d68 >>>> [ 32.501209] [0x1c]:0001285c >>>> [ 32.501444] [0x20]:14000400 >>>> [ 32.501687] [0x24]:00000020 >>>> [ 32.501922] [0x28]:0100000f >>>> [ 32.502157] [0x2c]:000c000b >>>> [ 32.502391] [0x30]:003c0003 >>>> [ 32.502626] [0x34]:0020ffe0 >>>> [ 32.502862] [0x38]:00800122 >>>> [ 32.503098] [0x3c]:00000009 >>>> [ 32.503336] mpt2sas_cm1: hba queue depth(3432), max chains per io(128) >>>> [ 32.503644] mpt2sas_cm1: request frame size(128), reply frame size(128) >>>> [ 32.503933] mpt2sas_cm1: _base_make_ioc_ready >>>> [ 32.504191] mpt2sas_cm1: _base_get_port_facts >>>> [ 32.534282] offset:data >>>> [ 32.534537] [0x00]:05070000 >>>> [ 32.534782] [0x04]:00000000 >>>> [ 32.535058] [0x08]:00000000 >>>> [ 32.536473] [0x0c]:00000000 >>>> [ 32.536710] [0x10]:00000000 >>>> [ 32.536946] [0x14]:00003000 >>>> [ 32.537183] [0x18]:00000078 >>>> [ 32.537420] mpt2sas_cm1: _base_allocate_memory_pools >>>> [ 32.537686] mpt2sas_cm1: scatter gather: sge_in_main_msg(3), sge_per_chain(15), sge_per_io(128), chains_per_io(9) >>>> [ 32.538232] mpt2sas_cm1: reply post free pool (0xffff8800bb3d0000): depth(6944),element_size(8), pool_size(54 kB) >>>> [ 32.538758] mpt2sas_cm1: reply_post_free_dma = (0xbb3d0000) >>>> [ 32.539030] mpt2sas_cm1: scsi host: can_queue depth (3307) >>>> [ 32.539378] mpt2sas_cm1: request pool(0xffff8800ba480000): depth(3432), frame_size(128), pool_size(429 kB) >>>> [ 32.539882] mpt2sas_cm1: request pool: dma(0xba480000) >>>> [ 32.540149] mpt2sas_cm1: scsiio(0xffff8800ba480000): depth(3307) >>>> [ 32.545893] mpt2sas_cm1: chain pool depth(29763), frame_size(128), pool_size(3720 kB) >>>> [ 32.546137] mpt2sas_cm1: hi_priority(0xffff8800ba4e7600): depth(60), start smid(3308) >>>> [ 32.546365] mpt2sas_cm1: internal(0xffff8800ba4e9400): depth(65), start smid(3368) >>>> [ 32.546651] mpt2sas_cm1: sense pool(0xffff8800ba880000): depth(3307), element_size(96), pool_size(310 kB) >>>> [ 32.547030] mpt2sas_cm1: sense_dma(0xba880000) >>>> [ 32.547537] mpt2sas_cm1: reply pool(0xffff880000100000): depth(3496), frame_size(128), pool_size(437 kB) >>>> [ 32.547921] mpt2sas_cm1: reply_dma(0x100000) >>>> [ 32.548117] mpt2sas_cm1: reply_free pool(0xffff8800ba964000): depth(3496), element_size(4), pool_size(13 kB) >>>> [ 32.548500] mpt2sas_cm1: reply_free_dma (0xba964000) >>>> [ 32.548698] mpt2sas_cm1: config page(0xffff8800ba960000): size(512) >>>> [ 32.548908] mpt2sas_cm1: config_page_dma(0xba960000) >>>> [ 32.549105] mpt2sas_cm1: Allocated physical memory: size(4964 kB) >>>> [ 32.549314] mpt2sas_cm1: Current Controller Queue Depth(3307),Max Controller Queue Depth(3432) >>>> [ 32.550950] mpt2sas_cm1: Scatter Gather Elements per IO(128) >>>> [ 32.551160] mpt2sas_cm1: _base_make_ioc_operational >>>> [ 32.551855] mpt2sas_cm1: _base_send_ioc_init >>>> [ 32.552051] offset:data >>>> [ 32.552224] [0x00]:02000004 >>>> [ 32.552400] [0x04]:00000000 >>>> [ 32.552576] [0x08]:00000000 >>>> [ 32.552761] [0x0c]:23000200 >>>> [ 32.552937] [0x10]:00000000 >>>> [ 32.553114] [0x14]:00000000 >>>> [ 32.553291] [0x18]:00200000 >>>> [ 32.553468] [0x1c]:0da81b20 >>>> [ 32.553685] [0x20]:00000000 >>>> [ 32.553862] [0x24]:00000000 >>>> [ 32.554038] [0x28]:ba480000 >>>> [ 32.554215] [0x2c]:00000000 >>>> [ 32.554393] [0x30]:bb3d0000 >>>> [ 32.554569] [0x34]:00000000 >>>> [ 32.554752] [0x38]:ba964000 >>>> [ 32.554929] [0x3c]:00000000 >>>> [ 32.555106] [0x40]:983f2ce6 >>>> [ 32.555283] [0x44]:00000153 >>>> [ 32.601516] offset:data >>>> [ 32.601768] [0x00]:02050004 >>>> [ 32.602003] [0x04]:00000000 >>>> [ 32.602239] [0x08]:00000000 >>>> [ 32.602474] [0x0c]:00000000 >>>> [ 32.602709] [0x10]:00000000 >>>> [ 32.602945] mpt2sas_cm1: _base_event_notification >>>> [ 62.593604] mpt2sas_cm1: _base_event_notification: timeout >>>> [ 62.593906] mf: >>>> >>>> [ 62.594127] 07000000 >>>> [ 62.594390] 00000000 >>>> [ 62.594438] 00000000 >>>> [ 62.594709] 00000000 >>>> [ 62.594757] 00000000 >>>> [ 62.595019] 0f2f7fff >>>> [ 62.595067] ffffff7c >>>> [ 62.595330] ffffffff >>>> [ 62.595377] >>>> >>>> [ 62.595808] ffffffff >>>> [ 62.595855] 00000000 >>>> [ 62.596117] 00000000 >>>> >>>> [ 62.596601] mpt2sas_cm1: mpt3sas_base_free_resources >>>> [ 62.596871] mpt2sas_cm1: _base_make_ioc_ready >>>> [ 62.597125] mpt2sas_cm1: sending message unit reset !! >>>> [ 62.599013] mpt2sas_cm1: message unit reset: SUCCESS >>>> [ 62.599283] mpt2sas_cm1: mpt3sas_base_unmap_resources >>>> [ 62.600443] mpt2sas_cm1: _base_release_memory_pools >>>> [ 62.600721] mpt2sas_cm1: request_pool(0xffff8800ba480000): free >>>> [ 62.601002] mpt2sas_cm1: sense_pool(0xffff8800ba880000): free >>>> [ 62.601280] mpt2sas_cm1: reply_pool(0xffff880000100000): free >>>> [ 62.601560] mpt2sas_cm1: reply_free_pool(0xffff8800ba964000): free >>>> [ 62.601845] mpt2sas_cm1: reply_post_free_pool(0xffff8800bb3d0000): free >>>> [ 62.602133] mpt2sas_cm1: config_page(0xffff8800ba960000): free >>>> [ 62.673591] mpt2sas_cm1: failure at drivers/scsi/mpt3sas/mpt3sas_scsih.c:8592/_scsih_probe()! >>> >>> These are for two controllers, I don't know whether the output from the >>> second is helpful at all - I added it anyway. >>> >>> >>> I managed to boot the same 4.5.0 kernel successfully after warm >>> rebooting from 4.1.20. That gave me this dmesg output (for comparison): >>> >>>> [ 2.057685] mpt3sas version 09.102.00.00 loaded >>>> [ 2.058371] mpt2sas_cm0: mpt3sas_base_attach >>>> [ 2.058632] mpt2sas_cm0: mpt3sas_base_map_resources >>>> [ 2.059583] mpt2sas_cm0: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3074748 kB) >>>> [ 2.059911] mpt2sas_cm0: _base_get_ioc_facts >>>> [ 2.060166] mpt2sas_cm0: _base_wait_for_iocstate >>>> [ 2.116337] offset:data >>>> [ 2.116576] [0x00]:03100200 >>>> [ 2.116817] [0x04]:00002300 >>>> [ 2.117051] [0x08]:00000000 >>>> [ 2.117285] [0x0c]:00000000 >>>> [ 2.117518] [0x10]:00000000 >>>> [ 2.117752] [0x14]:00010480 >>>> [ 2.117986] [0x18]:22130d68 >>>> [ 2.118220] [0x1c]:0001285c >>>> [ 2.119624] [0x20]:14000400 >>>> [ 2.119858] [0x24]:00000020 >>>> [ 2.120093] [0x28]:0100000f >>>> [ 2.120351] [0x2c]:000c000b >>>> [ 2.120586] [0x30]:003c0003 >>>> [ 2.120820] [0x34]:0020ffe0 >>>> [ 2.121055] [0x38]:00800122 >>>> [ 2.121288] [0x3c]:00000009 >>>> [ 2.121524] mpt2sas_cm0: hba queue depth(3432), max chains per io(128) >>>> [ 2.121808] mpt2sas_cm0: request frame size(128), reply frame size(128) >>>> [ 2.122195] mpt2sas_cm0: msix is supported, vector_count(1) >>>> [ 2.122468] mpt2sas_cm0: MSI-X vectors supported: 1, no of cores: 4, max_msix_vectors: -1 >>>> [ 2.123239] mpt2sas0-msix0: PCI-MSI-X enabled: IRQ 58 >>>> [ 2.123507] mpt2sas_cm0: iomem(0x00000000fd4fc000), mapped(0xffffc900000d0000), size(16384) >>>> [ 2.123816] mpt2sas_cm0: ioport(0x0000000000004000), size(256) >>>> [ 2.124623] mpt2sas_cm0: _base_get_ioc_facts >>>> [ 2.124878] mpt2sas_cm0: _base_wait_for_iocstate >>>> [ 2.180907] offset:data >>>> [ 2.181145] [0x00]:03100200 >>>> [ 2.181379] [0x04]:00002300 >>>> [ 2.181613] [0x08]:00000000 >>>> [ 2.181847] [0x0c]:00000000 >>>> [ 2.182081] [0x10]:00000000 >>>> [ 2.182315] [0x14]:00010480 >>>> [ 2.182547] [0x18]:22130d68 >>>> [ 2.182781] [0x1c]:0001285c >>>> [ 2.183014] [0x20]:14000400 >>>> [ 2.183248] [0x24]:00000020 >>>> [ 2.183481] [0x28]:0100000f >>>> [ 2.183720] [0x2c]:000c000b >>>> [ 2.183954] [0x30]:003c0003 >>>> [ 2.184190] [0x34]:0020ffe0 >>>> [ 2.184424] [0x38]:00800122 >>>> [ 2.184658] [0x3c]:00000009 >>>> [ 2.184893] mpt2sas_cm0: hba queue depth(3432), max chains per io(128) >>>> [ 2.185177] mpt2sas_cm0: request frame size(128), reply frame size(128) >>>> [ 2.185462] mpt2sas_cm0: _base_make_ioc_ready >>>> [ 2.185717] mpt2sas_cm0: _base_get_port_facts >>>> [ 2.214057] offset:data >>>> [ 2.214295] [0x00]:05070000 >>>> [ 2.214529] [0x04]:00000000 >>>> [ 2.214762] [0x08]:00000000 >>>> [ 2.214997] [0x0c]:00000000 >>>> [ 2.215230] [0x10]:00000000 >>>> [ 2.215464] [0x14]:00003000 >>>> [ 2.215697] [0x18]:00000078 >>>> [ 2.215931] mpt2sas_cm0: _base_allocate_memory_pools >>>> [ 2.216194] mpt2sas_cm0: scatter gather: sge_in_main_msg(3), sge_per_chain(15), sge_per_io(128), chains_per_io(9) >>>> [ 2.216734] mpt2sas_cm0: reply post free pool (0xffff8800bafc0000): depth(6944),element_size(8), pool_size(54 kB) >>>> [ 2.217244] mpt2sas_cm0: reply_post_free_dma = (0xbafc0000) >>>> [ 2.217514] mpt2sas_cm0: scsi host: can_queue depth (3307) >>>> [ 2.217866] mpt2sas_cm0: request pool(0xffff8800ba800000): depth(3432), frame_size(128), pool_size(429 kB) >>>> [ 2.218369] mpt2sas_cm0: request pool: dma(0xba800000) >>>> [ 2.218637] mpt2sas_cm0: scsiio(0xffff8800ba800000): depth(3307) >>>> [ 2.224773] mpt2sas_cm0: chain pool depth(29763), frame_size(128), pool_size(3720 kB) >>>> [ 2.225092] mpt2sas_cm0: hi_priority(0xffff8800ba867600): depth(60), start smid(3308) >>>> [ 2.225395] mpt2sas_cm0: internal(0xffff8800ba869400): depth(65), start smid(3368) >>>> [ 2.225958] mpt2sas_cm0: sense pool(0xffff8800ba480000): depth(3307), element_size(96), pool_size(310 kB) >>>> [ 2.226457] mpt2sas_cm0: sense_dma(0xba480000) >>>> [ 2.227039] mpt2sas_cm0: reply pool(0xffff8800ba500000): depth(3496), frame_size(128), pool_size(437 kB) >>>> [ 2.227413] mpt2sas_cm0: reply_dma(0xba500000) >>>> [ 2.227616] mpt2sas_cm0: reply_free pool(0xffff8800ba450000): depth(3496), element_size(4), pool_size(13 kB) >>>> [ 2.227992] mpt2sas_cm0: reply_free_dma (0xba450000) >>>> [ 2.228192] mpt2sas_cm0: config page(0xffff8800ba43b000): size(512) >>>> [ 2.228402] mpt2sas_cm0: config_page_dma(0xba43b000) >>>> [ 2.228598] mpt2sas_cm0: Allocated physical memory: size(4964 kB) >>>> [ 2.228806] mpt2sas_cm0: Current Controller Queue Depth(3307),Max Controller Queue Depth(3432) >>>> [ 2.229171] mpt2sas_cm0: Scatter Gather Elements per IO(128) >>>> [ 2.229378] mpt2sas_cm0: _base_make_ioc_operational >>>> [ 2.229959] mpt2sas_cm0: _base_send_ioc_init >>>> [ 2.230151] offset:data >>>> [ 2.230323] [0x00]:02000004 >>>> [ 2.230499] [0x04]:00000000 >>>> [ 2.230675] [0x08]:00000000 >>>> [ 2.230851] [0x0c]:23000200 >>>> [ 2.231026] [0x10]:00000000 >>>> [ 2.231201] [0x14]:00000000 >>>> [ 2.231376] [0x18]:00200000 >>>> [ 2.231551] [0x1c]:0da81b20 >>>> [ 2.231726] [0x20]:00000000 >>>> [ 2.231900] [0x24]:00000000 >>>> [ 2.232075] [0x28]:ba800000 >>>> [ 2.232250] [0x2c]:00000000 >>>> [ 2.232423] [0x30]:bafc0000 >>>> [ 2.232597] [0x34]:00000000 >>>> [ 2.232775] [0x38]:ba450000 >>>> [ 2.232950] [0x3c]:00000000 >>>> [ 2.233125] [0x40]:98596e4f >>>> [ 2.233299] [0x44]:00000153 >>>> [ 2.278752] offset:data >>>> [ 2.278988] [0x00]:02050004 >>>> [ 2.279220] [0x04]:00000000 >>>> [ 2.279453] [0x08]:00000000 >>>> [ 2.279685] [0x0c]:00000000 >>>> [ 2.279918] [0x10]:00000000 >>>> [ 2.280151] mpt2sas_cm0: _base_event_notification >>>> [ 2.280537] mpt2sas_cm0: _base_event_notification: complete >>>> [ 2.281694] mpt2sas_cm0: LSISAS2008: FWVersion(20.00.04.00), ChipRevision(0x03), BiosVersion(07.39.00.00) >>>> [ 2.282196] mpt2sas_cm0: Protocol=( >>>> [ 2.282261] Initiator >>>> [ 2.282522] ,Target >>>> [ 2.282567] ), >>>> [ 2.282824] Capabilities=( >>>> [ 2.282877] TLR >>>> [ 2.283132] ,EEDP >>>> [ 2.283175] ,Snapshot Buffer >>>> [ 2.283444] ,Diag Trace Buffer >>>> [ 2.283502] ,Task Set Full >>>> [ 2.283774] ,NCQ >>>> [ 2.283816] ) >>>> [ 2.284350] scsi host0: Fusion MPT SAS Host >>>> [ 2.299028] mpt2sas_cm0: sending port enable !! >>>> [ 2.299540] mpt2sas_cm0: Discovery: (start) >>>> >>>> [ 2.299972] mpt2sas_cm0: SAS Enclosure Device Status Change >>>> [ 2.299984] mpt2sas_cm0: discovery event: (start) >>>> >>>> [ 2.300554] mpt2sas_cm0: SAS Topology Change List >>>> [ 2.300759] mpt2sas_cm0: Discovery: (stop) >>>> >>>> [ 2.301146] mpt2sas_cm0: Discovery: (start) >>>> >>>> [ 2.301535] mpt2sas_cm0: Discovery: (stop) >>>> >>>> [ 2.301927] mpt2sas_cm0: Discovery: (start) >>>> >>>> [ 2.302316] mpt2sas_cm0: Discovery: (stop) >>>> >>>> [ 2.302707] mpt2sas_cm0: Discovery: (start) >>>> >>>> [ 2.304908] mpt2sas_cm0: Discovery: (stop) >>>> >>>> [ 2.305297] mpt2sas_cm0: Discovery: (start) >>>> >>>> [ 2.306776] mpt2sas_cm0: Discovery: (stop) >>>> >>>> [ 2.307166] mpt2sas_cm0: Discovery: (start) >>>> >>>> [ 2.307559] mpt2sas_cm0: Discovery: (stop) >>>> >>>> [ 2.307948] mpt2sas_cm0: Discovery: (start) >>>> >>>> [ 2.308336] mpt2sas_cm0: Discovery: (stop) >>>> >>>> [ 2.311738] mpt2sas_cm0: host_add: handle(0x0001), sas_addr(0x500605b003683dd0), phys(8) >>>> [ 2.312097] mpt2sas_cm0: enclosure status change: (enclosure add) >>>> handle(0x0001), enclosure logical id(0x500605b003683dd0) number slots(0) >>>> [ 2.312551] mpt2sas_cm0: sas topology change: (responding) >>>> [ 2.312768] handle(0x0000), enclosure_handle(0x0001) start_phy(00), count(8) >>>> [ 2.313003] phy(01), attached_handle(0x0009): target add: link rate: new(0x0a), old(0x00) >>>> [ 2.313250] phy(02), attached_handle(0x000a): target add: link rate: new(0x09), old(0x00) >>>> [ 2.313498] phy(03), attached_handle(0x000b): target add: link rate: new(0x09), old(0x00) >>>> [ 2.313745] phy(04), attached_handle(0x000c): target add: link rate: new(0x09), old(0x00) >>>> [ 2.313992] phy(05), attached_handle(0x000d): target add: link rate: new(0x09), old(0x00) >>>> [ 2.314248] phy(06), attached_handle(0x000e): target add: link rate: new(0x09), old(0x00) >>>> [ 2.314495] phy(07), attached_handle(0x000f): target add: link rate: new(0x09), old(0x00) >>>> [ 2.314747] mpt2sas_cm0: updating handles for sas_host(0x500605b003683dd0) >>>> [ 2.316041] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x0009), sas_addr(0x4433221101000000) >>>> [ 2.316465] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 2) >>>> [ 2.317200] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000a), sas_addr(0x4433221102000000) >>>> [ 2.317669] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 1) >>>> [ 2.318431] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000b), sas_addr(0x4433221103000000) >>>> [ 2.318900] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 0) >>>> [ 2.319366] mpt2sas_cm0: _scsih_determine_boot_device: current_boot_device(0x4433221103000000) >>>> [ 2.320151] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000c), sas_addr(0x4433221104000000) >>>> [ 2.321371] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 7) >>>> [ 2.322137] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000d), sas_addr(0x4433221105000000) >>>> [ 2.322606] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 6) >>>> [ 2.323367] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000e), sas_addr(0x4433221106000000) >>>> [ 2.323834] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 5) >>>> [ 2.324602] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000f), sas_addr(0x4433221107000000) >>>> [ 2.325071] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 4) >>>> [ 2.325541] mpt2sas_cm0: discovery event: (stop) >>>> >>>> [ 2.326017] mpt2sas_cm0: discovery event: (start) >>>> >>>> [ 2.326492] mpt2sas_cm0: discovery event: (stop) >>>> >>>> [ 2.326975] mpt2sas_cm0: discovery event: (start) >>>> >>>> [ 2.327450] mpt2sas_cm0: discovery event: (stop) >>>> >>>> [ 2.327923] mpt2sas_cm0: discovery event: (start) >>>> >>>> [ 2.328396] mpt2sas_cm0: discovery event: (stop) >>>> >>>> [ 2.328868] mpt2sas_cm0: discovery event: (start) >>>> >>>> [ 2.329340] mpt2sas_cm0: discovery event: (stop) >>>> >>>> [ 2.329816] mpt2sas_cm0: discovery event: (start) >>>> >>>> [ 2.330316] mpt2sas_cm0: discovery event: (stop) >>>> >>>> [ 2.330797] mpt2sas_cm0: discovery event: (start) >>>> >>>> [ 2.331269] mpt2sas_cm0: discovery event: (stop) >>>> >>>> [ 2.331740] mpt2sas_cm0: port enable: complete from worker thread >>>> [ 2.350236] mpt2sas_cm0: port enable: SUCCESS >>>> [ 2.356432] scsi 0:0:0:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 >>>> [ 2.356683] scsi 0:0:0:0: SATA: handle(0x000b), sas_addr(0x4433221103000000), phy(3), device_name(0x5000c5000267c9f8) >>>> [ 2.357080] scsi 0:0:0:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(0) >>>> [ 2.357405] scsi 0:0:0:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>> [ 2.383043] scsi 0:0:1:0: Direct-Access ATA Hitachi HDS5C302 A800 PQ: 0 ANSI: 6 >>>> [ 2.383296] scsi 0:0:1:0: SATA: handle(0x0009), sas_addr(0x4433221101000000), phy(1), device_name(0x5000cca369cdd311) >>>> [ 2.383684] scsi 0:0:1:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(2) >>>> [ 2.384028] scsi 0:0:1:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>> [ 2.405088] scsi 0:0:2:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 >>>> [ 2.405346] scsi 0:0:2:0: SATA: handle(0x000a), sas_addr(0x4433221102000000), phy(2), device_name(0x5000c5000ccfbd32) >>>> [ 2.405735] scsi 0:0:2:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(1) >>>> [ 2.406082] scsi 0:0:2:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>> [ 2.424125] scsi 0:0:3:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 >>>> [ 2.424373] scsi 0:0:3:0: SATA: handle(0x000c), sas_addr(0x4433221104000000), phy(4), device_name(0x5000c5000267abee) >>>> [ 2.424763] scsi 0:0:3:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(7) >>>> [ 2.425108] scsi 0:0:3:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>> [ 2.444834] scsi 0:0:4:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 >>>> [ 2.445086] scsi 0:0:4:0: SATA: handle(0x000d), sas_addr(0x4433221105000000), phy(5), device_name(0x5000c50009c0e5e6) >>>> [ 2.445478] scsi 0:0:4:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(6) >>>> [ 2.445803] scsi 0:0:4:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>> [ 2.464065] scsi 0:0:5:0: Direct-Access ATA ST3750330NS SN16 PQ: 0 ANSI: 6 >>>> [ 2.464312] scsi 0:0:5:0: SATA: handle(0x000e), sas_addr(0x4433221106000000), phy(6), device_name(0x5000c5003cb9ac10) >>>> [ 2.464699] scsi 0:0:5:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(5) >>>> [ 2.465048] scsi 0:0:5:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>> [ 2.484016] scsi 0:0:6:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 >>>> [ 2.484266] scsi 0:0:6:0: SATA: handle(0x000f), sas_addr(0x4433221107000000), phy(7), device_name(0x5000c5000839b69e) >>>> [ 2.484655] scsi 0:0:6:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(4) >>>> [ 2.485001] scsi 0:0:6:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>> [ 2.500660] mpt2sas_cm1: mpt3sas_base_attach >>>> [ 2.500861] mpt2sas_cm1: mpt3sas_base_map_resources >>>> [ 2.501599] mpt2sas_cm1: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3074748 kB) >>>> [ 2.501847] mpt2sas_cm1: _base_get_ioc_facts >>>> [ 2.502036] mpt2sas_cm1: _base_wait_for_iocstate >>>> [ 2.559080] offset:data >>>> [ 2.559318] [0x00]:03100200 >>>> [ 2.559552] [0x04]:00002300 >>>> [ 2.559785] [0x08]:00000000 >>>> [ 2.560020] [0x0c]:00000000 >>>> [ 2.560277] [0x10]:00000000 >>>> [ 2.560511] [0x14]:00010480 >>>> [ 2.560745] [0x18]:22130d68 >>>> [ 2.560978] [0x1c]:0001285c >>>> [ 2.561210] [0x20]:14000400 >>>> [ 2.561443] [0x24]:00000020 >>>> [ 2.561675] [0x28]:0100000f >>>> [ 2.561907] [0x2c]:000c000b >>>> [ 2.562139] [0x30]:003c0003 >>>> [ 2.562371] [0x34]:0020ffe0 >>>> [ 2.562602] [0x38]:00800122 >>>> [ 2.562839] [0x3c]:00000009 >>>> [ 2.563073] mpt2sas_cm1: hba queue depth(3432), max chains per io(128) >>>> [ 2.563355] mpt2sas_cm1: request frame size(128), reply frame size(128) >>>> [ 2.563745] mpt2sas_cm1: msix is supported, vector_count(1) >>>> [ 2.564016] mpt2sas_cm1: MSI-X vectors supported: 1, no of cores: 4, max_msix_vectors: 8 >>>> [ 2.564918] mpt2sas1-msix0: PCI-MSI-X enabled: IRQ 59 >>>> [ 2.566189] mpt2sas_cm1: iomem(0x00000000fd1fc000), mapped(0xffffc900000d8000), size(16384) >>>> [ 2.566498] mpt2sas_cm1: ioport(0x0000000000007000), size(256) >>>> [ 2.567328] mpt2sas_cm1: _base_get_ioc_facts >>>> [ 2.567583] mpt2sas_cm1: _base_wait_for_iocstate >>>> [ 2.625125] offset:data >>>> [ 2.625364] [0x00]:03100200 >>>> [ 2.625597] [0x04]:00002300 >>>> [ 2.625830] [0x08]:00000000 >>>> [ 2.626064] [0x0c]:00000000 >>>> [ 2.626296] [0x10]:00000000 >>>> [ 2.626529] [0x14]:00010480 >>>> [ 2.626769] [0x18]:22130d68 >>>> [ 2.627002] [0x1c]:0001285c >>>> [ 2.627235] [0x20]:14000400 >>>> [ 2.627467] [0x24]:00000020 >>>> [ 2.627702] [0x28]:0100000f >>>> [ 2.627936] [0x2c]:000c000b >>>> [ 2.628170] [0x30]:003c0003 >>>> [ 2.628403] [0x34]:0020ffe0 >>>> [ 2.628638] [0x38]:00800122 >>>> [ 2.628872] [0x3c]:00000009 >>>> [ 2.629107] mpt2sas_cm1: hba queue depth(3432), max chains per io(128) >>>> [ 2.629388] mpt2sas_cm1: request frame size(128), reply frame size(128) >>>> [ 2.629671] mpt2sas_cm1: _base_make_ioc_ready >>>> [ 2.629928] mpt2sas_cm1: _base_get_port_facts >>>> [ 2.660127] offset:data >>>> [ 2.660389] [0x00]:05070000 >>>> [ 2.660623] [0x04]:00000000 >>>> [ 2.660858] [0x08]:00000000 >>>> [ 2.661093] [0x0c]:00000000 >>>> [ 2.661326] [0x10]:00000000 >>>> [ 2.661562] [0x14]:00003000 >>>> [ 2.661796] [0x18]:00000078 >>>> [ 2.664346] mpt2sas_cm1: _base_allocate_memory_pools >>>> [ 2.664608] mpt2sas_cm1: scatter gather: sge_in_main_msg(3), sge_per_chain(15), sge_per_io(128), chains_per_io(9) >>>> [ 2.665142] mpt2sas_cm1: reply post free pool (0xffff8800b8b10000): depth(6944),element_size(8), pool_size(54 kB) >>>> [ 2.666671] mpt2sas_cm1: reply_post_free_dma = (0xb8b10000) >>>> [ 2.666954] mpt2sas_cm1: scsi host: can_queue depth (3307) >>>> [ 2.667311] mpt2sas_cm1: request pool(0xffff8800b8b80000): depth(3432), frame_size(128), pool_size(429 kB) >>>> [ 2.667813] mpt2sas_cm1: request pool: dma(0xb8b80000) >>>> [ 2.668080] mpt2sas_cm1: scsiio(0xffff8800b8b80000): depth(3307) >>>> [ 2.674131] mpt2sas_cm1: chain pool depth(29763), frame_size(128), pool_size(3720 kB) >>>> [ 2.674448] mpt2sas_cm1: hi_priority(0xffff8800b8be7600): depth(60), start smid(3308) >>>> [ 2.674750] mpt2sas_cm1: internal(0xffff8800b8be9400): depth(65), start smid(3368) >>>> [ 2.675105] mpt2sas_cm1: sense pool(0xffff8800b8100000): depth(3307), element_size(96), pool_size(310 kB) >>>> [ 2.675605] mpt2sas_cm1: sense_dma(0xb8100000) >>>> [ 2.675944] mpt2sas_cm1: reply pool(0xffff8800b8180000): depth(3496), frame_size(128), pool_size(437 kB) >>>> [ 2.676443] mpt2sas_cm1: reply_dma(0xb8180000) >>>> [ 2.676702] mpt2sas_cm1: reply_free pool(0xffff8800b80a0000): depth(3496), element_size(4), pool_size(13 kB) >>>> [ 2.677124] mpt2sas_cm1: reply_free_dma (0xb80a0000) >>>> [ 2.677322] mpt2sas_cm1: config page(0xffff8800b807f000): size(512) >>>> [ 2.677532] mpt2sas_cm1: config_page_dma(0xb807f000) >>>> [ 2.677728] mpt2sas_cm1: Allocated physical memory: size(4964 kB) >>>> [ 2.677936] mpt2sas_cm1: Current Controller Queue Depth(3307),Max Controller Queue Depth(3432) >>>> [ 2.678304] mpt2sas_cm1: Scatter Gather Elements per IO(128) >>>> [ 2.678514] mpt2sas_cm1: _base_make_ioc_operational >>>> [ 2.679081] mpt2sas_cm1: _base_send_ioc_init >>>> [ 2.679275] offset:data >>>> [ 2.679448] [0x00]:02000004 >>>> [ 2.679625] [0x04]:00000000 >>>> [ 2.679805] [0x08]:00000000 >>>> [ 2.681200] [0x0c]:23000200 >>>> [ 2.681377] [0x10]:00000000 >>>> [ 2.681554] [0x14]:00000000 >>>> [ 2.681729] [0x18]:00200000 >>>> [ 2.681906] [0x1c]:0da81b20 >>>> [ 2.682082] [0x20]:00000000 >>>> [ 2.682259] [0x24]:00000000 >>>> [ 2.682435] [0x28]:b8b80000 >>>> [ 2.682611] [0x2c]:00000000 >>>> [ 2.682787] [0x30]:b8b10000 >>>> [ 2.682963] [0x34]:00000000 >>>> [ 2.683139] [0x38]:b80a0000 >>>> [ 2.683314] [0x3c]:00000000 >>>> [ 2.683489] [0x40]:98597011 >>>> [ 2.683665] [0x44]:00000153 >>>> [ 2.729849] offset:data >>>> [ 2.730089] [0x00]:02050004 >>>> [ 2.730349] [0x04]:00000000 >>>> [ 2.730586] [0x08]:00000000 >>>> [ 2.730822] [0x0c]:00000000 >>>> [ 2.731058] [0x10]:00000000 >>>> [ 2.731295] mpt2sas_cm1: _base_event_notification >>>> [ 2.731606] mpt2sas_cm1: _base_event_notification: complete >>>> [ 2.732501] mpt2sas_cm1: LSISAS2008: FWVersion(20.00.04.00), ChipRevision(0x02), BiosVersion(07.39.00.00) >>>> [ 2.733010] mpt2sas_cm1: Protocol=( >>>> [ 2.733074] Initiator >>>> [ 2.733339] ,Target >>>> [ 2.733384] ), >>>> [ 2.733642] Capabilities=( >>>> [ 2.733696] TLR >>>> [ 2.733952] ,EEDP >>>> [ 2.733995] ,Snapshot Buffer >>>> [ 2.734268] ,Diag Trace Buffer >>>> [ 2.734326] ,Task Set Full >>>> [ 2.734595] ,NCQ >>>> [ 2.734637] ) >>>> [ 2.735155] scsi host1: Fusion MPT SAS Host >>>> [ 2.749047] mpt2sas_cm1: sending port enable !! >>>> [ 2.749563] mpt2sas_cm1: Discovery: (start) >>>> >>>> [ 2.749989] mpt2sas_cm1: SAS Enclosure Device Status Change >>>> [ 2.750001] mpt2sas_cm1: discovery event: (start) >>>> >>>> [ 2.750578] mpt2sas_cm1: SAS Topology Change List >>>> [ 2.750788] mpt2sas_cm1: Discovery: (stop) >>>> >>>> [ 2.751181] mpt2sas_cm1: Discovery: (start) >>>> >>>> [ 2.751571] mpt2sas_cm1: Discovery: (stop) >>>> >>>> [ 2.752002] mpt2sas_cm1: Discovery: (start) >>>> >>>> [ 2.752391] mpt2sas_cm1: Discovery: (stop) >>>> >>>> [ 2.752779] mpt2sas_cm1: Discovery: (start) >>>> >>>> [ 2.754205] mpt2sas_cm1: Discovery: (stop) >>>> >>>> [ 2.754593] mpt2sas_cm1: Discovery: (start) >>>> >>>> [ 2.754983] mpt2sas_cm1: Discovery: (stop) >>>> >>>> [ 2.755371] mpt2sas_cm1: Discovery: (start) >>>> >>>> [ 2.755762] mpt2sas_cm1: Discovery: (stop) >>>> >>>> [ 2.759602] mpt2sas_cm1: host_add: handle(0x0001), sas_addr(0x500605b0026f79b0), phys(8) >>>> [ 2.759969] mpt2sas_cm1: enclosure status change: (enclosure add) >>>> handle(0x0001), enclosure logical id(0x500605b0026f79b0) number slots(0) >>>> [ 2.760407] mpt2sas_cm1: sas topology change: (responding) >>>> [ 2.760612] handle(0x0000), enclosure_handle(0x0001) start_phy(00), count(8) >>>> [ 2.760834] phy(02), attached_handle(0x000e): target add: link rate: new(0x0a), old(0x00) >>>> [ 2.761066] phy(03), attached_handle(0x000b): target add: link rate: new(0x0a), old(0x00) >>>> [ 2.761304] phy(04), attached_handle(0x000d): target add: link rate: new(0x09), old(0x00) >>>> [ 2.761538] phy(05), attached_handle(0x0009): target add: link rate: new(0x09), old(0x00) >>>> [ 2.761771] phy(06), attached_handle(0x000a): target add: link rate: new(0x09), old(0x00) >>>> [ 2.762002] phy(07), attached_handle(0x000c): target add: link rate: new(0x09), old(0x00) >>>> [ 2.762235] mpt2sas_cm1: updating handles for sas_host(0x500605b0026f79b0) >>>> [ 2.763653] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x000e), sas_addr(0x4433221102000000) >>>> [ 2.764036] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 1) >>>> [ 2.764772] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x000b), sas_addr(0x4433221103000000) >>>> [ 2.765147] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 0) >>>> [ 2.765891] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x000d), sas_addr(0x4433221104000000) >>>> [ 2.767250] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 7) >>>> [ 2.768009] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x0009), sas_addr(0x4433221105000000) >>>> [ 2.768394] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 6) >>>> [ 2.769136] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x000a), sas_addr(0x4433221106000000) >>>> [ 2.769510] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 5) >>>> [ 2.769888] mpt2sas_cm1: _scsih_determine_boot_device: current_boot_device(0x4433221106000000) >>>> [ 2.770641] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x000c), sas_addr(0x4433221107000000) >>>> [ 2.771025] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 4) >>>> [ 2.771405] mpt2sas_cm1: discovery event: (stop) >>>> >>>> [ 2.771788] mpt2sas_cm1: discovery event: (start) >>>> >>>> [ 2.772172] mpt2sas_cm1: discovery event: (stop) >>>> >>>> [ 2.772554] mpt2sas_cm1: discovery event: (start) >>>> >>>> [ 2.772942] mpt2sas_cm1: discovery event: (stop) >>>> >>>> [ 2.773326] mpt2sas_cm1: discovery event: (start) >>>> >>>> [ 2.773709] mpt2sas_cm1: discovery event: (stop) >>>> >>>> [ 2.774090] mpt2sas_cm1: discovery event: (start) >>>> >>>> [ 2.774474] mpt2sas_cm1: discovery event: (stop) >>>> >>>> [ 2.774855] mpt2sas_cm1: discovery event: (start) >>>> >>>> [ 2.775237] mpt2sas_cm1: discovery event: (stop) >>>> >>>> [ 2.775619] mpt2sas_cm1: port enable: complete from worker thread >>>> [ 2.780192] mpt2sas_cm1: port enable: SUCCESS >>>> [ 2.782404] scsi 1:0:0:0: Direct-Access ATA Hitachi HDP72505 A5BA PQ: 0 ANSI: 6 >>>> [ 2.782651] scsi 1:0:0:0: SATA: handle(0x000a), sas_addr(0x4433221106000000), phy(6), device_name(0x5000cca34dc05584) >>>> [ 2.783039] scsi 1:0:0:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(5) >>>> [ 2.783390] scsi 1:0:0:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>> [ 2.803032] scsi 1:0:1:0: Direct-Access ATA ST8000AS0002-1NA AR15 PQ: 0 ANSI: 6 >>>> [ 2.803272] scsi 1:0:1:0: SATA: handle(0x000e), sas_addr(0x4433221102000000), phy(2), device_name(0x5000c500908f1d05) >>>> [ 2.803660] scsi 1:0:1:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(1) >>>> [ 2.803981] scsi 1:0:1:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>> [ 2.821712] scsi 1:0:2:0: Direct-Access ATA ST3000DM001-1CH1 CC43 PQ: 0 ANSI: 6 >>>> [ 2.821963] scsi 1:0:2:0: SATA: handle(0x000b), sas_addr(0x4433221103000000), phy(3), device_name(0x5000c5004dfd2a8a) >>>> [ 2.822352] scsi 1:0:2:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(0) >>>> [ 2.822694] scsi 1:0:2:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>> [ 2.844233] scsi 1:0:3:0: Direct-Access ATA ST3500320NS SN16 PQ: 0 ANSI: 6 >>>> [ 2.844483] scsi 1:0:3:0: SATA: handle(0x000d), sas_addr(0x4433221104000000), phy(4), device_name(0x5000c50009dca65b) >>>> [ 2.844870] scsi 1:0:3:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(7) >>>> [ 2.845216] scsi 1:0:3:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>> [ 2.868963] scsi 1:0:4:0: Direct-Access ATA SAMSUNG HD401LJ 0-15 PQ: 0 ANSI: 6 >>>> [ 2.870994] scsi 1:0:4:0: SATA: handle(0x0009), sas_addr(0x4433221105000000), phy(5), device_name(0x695d550daf678093) >>>> [ 2.871382] scsi 1:0:4:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(6) >>>> [ 2.871728] scsi 1:0:4:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>> [ 2.894004] scsi 1:0:5:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 >>>> [ 2.894257] scsi 1:0:5:0: SATA: handle(0x000c), sas_addr(0x4433221107000000), phy(7), device_name(0x5000c5000266bb02) >>>> [ 2.894646] scsi 1:0:5:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(4) >>>> [ 2.894972] scsi 1:0:5:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>> >>> I don't see a clear pattern yet, but I suspect warm rebooting >=4.2 >>> after having run 4.1.x leads to sucessful driver inits. But I also >>> remember having had cold boots, with kernels >=4.2 that worked fine >>> (obviously not all of the time). <=4.1.20 kernels on the other hand boot >>> fine every single time. >>> >>> Interestingly the igb driver (ethernet) seems to be acting up at least >>> with 4.5.0 on exactly the same boots when mpt2sas init fails. I don't >>> know whether this could be connected or not (I just became aware of this >>> coincidence). >>> >>> >>> --- >>> Matthias >>> >>> >>> Am 21.03.2016 um 05:53 schrieb Sreekanth Reddy: >>>> Hi Matthias, >>>> >>>> Can you please share us the driver logs with driver logging_level set >>>> to 0x3f8. So that we can get more info from this log. >>>> >>>> Thanks, >>>> Sreekanth >>>> >>>> On Mon, Mar 21, 2016 at 1:44 AM, Matthias Prager >>>> <linux@matthiasprager.de> wrote: >>>>> Hello, >>>>> >>>>> I don't know what's the correct procedure, whether I should file a bug or first report this issue on the kernel mailing-list. So please feel free to tell me to open a ticket in the bugtracker (bugzilla.kernel.org?). >>>>> >>>>> But first let me present the issue I encounter: >>>>> >>>>> Kernels >= 4.2 (4.2.1 was the first on I tried, but also 4.3, 4.4 and 4.5) fail to load the mpt2sas driver on most (but not all) boots. Kernels <= 4.1.x work fine every single time (4.1.19 was the latest I tried, also 3.18.29). >>>>> >>>>> Here is the dmesg output for a failed driver init with Kernel 4.5.0: >>>>>> [ 2.068313] mpt3sas version 09.102.00.00 loaded >>>>>> [ 2.069412] mpt2sas_cm0: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3074748 kB) >>>>>> [ 2.125260] mpt2sas_cm0: MSI-X vectors supported: 1, no of cores: 4, max_msix_vectors: -1 >>>>>> [ 2.125996] mpt2sas0-msix0: PCI-MSI-X enabled: IRQ 58 >>>>>> [ 2.126199] mpt2sas_cm0: iomem(0x00000000fd4fc000), mapped(0xffffc900000d0000), size(16384) >>>>>> [ 2.126430] mpt2sas_cm0: ioport(0x0000000000004000), size(256) >>>>>> [ 2.216371] mpt2sas_cm0: Allocated physical memory: size(4964 kB) >>>>>> [ 2.216600] mpt2sas_cm0: Current Controller Queue Depth(3307),Max Controller Queue Depth(3432) >>>>>> [ 2.217004] mpt2sas_cm0: Scatter Gather Elements per IO(128) >>>>>> [ 5.086959] floppy0: no floppy controllers found >>>>>> [ 32.256720] mpt2sas_cm0: _base_event_notification: timeout >>>>>> [ 32.256940] mf: >>>>>> >>>>>> [ 32.257106] 07000000 >>>>>> [ 32.257302] 00000000 >>>>>> [ 32.257337] 00000000 >>>>>> [ 32.257533] 00000000 >>>>>> [ 32.257568] 00000000 >>>>>> [ 32.257764] 0f2f7fff >>>>>> [ 32.257800] ffffff7c >>>>>> [ 32.257995] ffffffff >>>>>> [ 32.258031] >>>>>> >>>>>> [ 32.258352] ffffffff >>>>>> [ 32.258387] 00000000 >>>>>> [ 32.258582] 00000000 >>>>>> >>>>>> [ 32.258950] mpt2sas_cm0: sending message unit reset !! >>>>>> [ 32.260688] mpt2sas_cm0: message unit reset: SUCCESS >>>>>> [ 32.325956] mpt2sas_cm0: failure at drivers/scsi/mpt3sas/mpt3sas_scsih.c:8592/_scsih_probe()! >>>>> >>>>> For comparison here is a dmesg output for a successful boot on Kernel 4.1.15: >>>>>> [ 2.035568] mpt2sas version 20.100.00.00 loaded >>>>>> [ 2.037243] mpt2sas0: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (2046352 kB) >>>>>> [ 2.755374] mpt2sas0: MSI-X vectors supported: 1, no of cores: 3, max_msix_vectors: 8 >>>>>> [ 2.756377] mpt2sas0-msix0: PCI-MSI-X enabled: IRQ 58 >>>>>> [ 2.756708] mpt2sas0: iomem(0x00000000fd5fc000), mapped(0xffffc900000d0000), size(16384) >>>>>> [ 2.757083] mpt2sas0: ioport(0x0000000000004000), size(256) >>>>>> [ 3.842944] mpt2sas0: Allocated physical memory: size(4964 kB) >>>>>> [ 3.843303] mpt2sas0: Current Controller Queue Depth(3307), Max Controller Queue Depth(3432) >>>>>> [ 3.843717] mpt2sas0: Scatter Gather Elements per IO(128) >>>>>> [ 4.415980] mpt2sas0: LSISAS2008: FWVersion(20.00.04.00), ChipRevision(0x03), BiosVersion(07.39.00.00) >>>>>> [ 4.416618] mpt2sas0: Protocol=(Initiator,Target), Capabilities=(TLR,EEDP,Snapshot Buffer,Diag Trace Buffer,Task Set Full,NCQ) >>>>>> [ 4.417846] scsi host0: Fusion MPT SAS Host >>>>>> [ 4.436865] mpt2sas0: sending port enable !! >>>>>> [ 4.440460] mpt2sas0: host_add: handle(0x0001), sas_addr(0xxxxxxxxxxxxxxxxx), phys(8) >>>>>> >>>>>> ... >>>>>> [ 4.444045] scsi 0:0:0:0: Direct-Access ATA Hitachi HDS5C302 A800 PQ: 0 ANSI: 6 >>>>>> [ 4.444338] scsi 0:0:0:0: SATA: handle(0x0009), sas_addr(0xxxxxxxxxxxxxxxxx), phy(1), device_name(0xxxxxxxxxxxxxxxxx) >>>>>> [ 4.444823] scsi 0:0:0:0: SATA: enclosure_logical_id(0xxxxxxxxxxxxxxxxx), slot(2) >>>>>> [ 4.445197] scsi 0:0:0:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>>> ... (n times for n drives) >>>>>> >>>>>> [ 4.515443] mpt2sas0: port enable: SUCCESS >>>>> >>>>> >>>>> The Controller(s) are all Avego/LSI 9211-8i running the latest version of IT firmware (v20.00.04.00). These are passed through to a gentoo-linux VM on an ESXi 5.1 host (latest patchlevel). I have two of these systems (one production one testing) with nearly identical hardware (Supermicro X8DTi-F boards with 2x Intel Westmere CPUs). I also have an older set of systems running the same software config (Intel S3200SHLC boards with single Core2Quad) which exhibit the same buggy behavior. >>>>> >>>>> The 'uname -a' line on the current testing system looks like this: >>>>>> Linux pserver2 4.1.19-gentoo #4 SMP Thu Mar 17 16:02:48 CET 2016 x86_64 Intel(R) Xeon(R) CPU E5506 @ 2.13GHz GenuineIntel GNU/Linux >>>>> p >>>>> >>>>> There seem to be other people with similar issues: >>>>> <https://bbs.archlinux.org/viewtopic.php?id=209495> >>>>> >>>>> Any thoughts? >>>>> >>>>> --- >>>>> Matthias >>> ^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [BUG] mpt2sas: driver init fails on kernel >=4.2 for 9211-8i IT 2016-03-21 16:30 ` Matthias Prager @ 2016-03-22 10:52 ` Sreekanth Reddy 2016-03-22 21:02 ` Matthias Prager 0 siblings, 1 reply; 13+ messages in thread From: Sreekanth Reddy @ 2016-03-22 10:52 UTC (permalink / raw) To: Matthias Prager; +Cc: linux-scsi Hi Matthias, Thanks for providing detail explanation. Currently I am trying to reproduce this issue locally. I have used the same HBA card but still I am not able to reproduce this issue on 4.5 kernel. I will try for few more times and I will also try to get the diff between 4.1 to 4.5 kernels w.r.t msix vectors support. Meanwhile can you please provide me the output of "lspci -vvv" command for LSI SAS2 HBA's and also hexdump of config sysfs parameter for SAS2 pci device. I need this data to be collected before "timeout" print is observed, or in the mpt3sas_base.c file and in the mpt3sas_base_attach(). return from mpt3sas_base_attach() function if return value of mpt3sas_base_map_resources() is non zero instead of freeing the resources, as shown below --------------------------------------------------------------------------- r = mpt3sas_base_map_resources(ioc); if (r) - goto out_free_resources; + return r; ----------------------------------------------------------------------------- Also are you sure that this issue won't occur on less than 4.1 kernel? Thanks, Sreekanth On Mon, Mar 21, 2016 at 10:00 PM, Matthias Prager <linux@matthiasprager.de> wrote: > Am 21.03.2016 um 16:52 schrieb Matthias Prager: >> Hi Sreekanth, >> >> thanks for digging into this issue. Regarding the 4.5.0 after 4.1.20 >> boot statement, I will try to express myself better: >> >> I first started the system with the 4.1.20 kernel. Then I issued an >> 'init 6' warm-reboot and chose to boot the 4.5.0 kernel. This procedure >> often works (i.e. I'm able to boot the newer kernels (>=4.2) this way >> with mpt2sas initializing just fine). > One small addition: warm-rebooting kernel 4.5.0 from kernel 4.5.0 > reliably leads to this issue manifesting (mpt2sas driver not initializing). > >> >> I will try the msix_disable parameter and report back. Maybe kernel >> version 4.2 broke interrupt handling somehow? > With the msix_disable parameter set kernels 4.5.0, 4.4.5, 4.3.3 and > 4.2.1 boot without the mpt2sas init issue. I also tried the pci=nomsi > paremeter instead, which also works fine. > > The igb ethernet-driver issue I mentioned as possibly related has not > changed with pci=nomsi. So I'm assuming it is not the same issue, but > possibly related, since it also occurs on kernels >=4.2. > >> >> --- >> Matthias >> >> >> Am 21.03.2016 um 14:59 schrieb Sreekanth Reddy: >>> Hi Matthias, >>> >>> Thanks for providing the logs. In these logs, I am not observing any >>> such a prints which should be suspected for this issue. >>> >>> Can you please try once by setting mpt3sas driver's "msix_disable" >>> module parameter to one. >>> >>> Also, can you please elaborate below statement for me, I am not able >>> understand this statement >>> "I managed to boot the same 4.5.0 kernel successfully after warm >>> rebooting from 4.1.20" >>> >>> Thanks, >>> Sreekanth >>> >>> On Mon, Mar 21, 2016 at 2:48 PM, Matthias Prager >>> <linux@matthiasprager.de> wrote: >>>> Hi Sreekanth, >>>> >>>> thank you for replying so quickly. Here are the logs you requested >>>> (kernel 4.5.0): >>>> >>>>> [ 2.083177] mpt3sas version 09.102.00.00 loaded >>>>> [ 2.083757] mpt2sas_cm0: mpt3sas_base_attach >>>>> [ 2.083956] mpt2sas_cm0: mpt3sas_base_map_resources >>>>> [ 2.084708] mpt2sas_cm0: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3074748 kB) >>>>> [ 2.084964] mpt2sas_cm0: _base_get_ioc_facts >>>>> [ 2.085154] mpt2sas_cm0: _base_wait_for_iocstate >>>>> [ 2.140893] offset:data >>>>> [ 2.141082] [0x00]:03100200 >>>>> [ 2.141257] [0x04]:00002300 >>>>> [ 2.141432] [0x08]:00000000 >>>>> [ 2.141606] [0x0c]:00000000 >>>>> [ 2.141780] [0x10]:00000000 >>>>> [ 2.141955] [0x14]:00010480 >>>>> [ 2.142129] [0x18]:22130d68 >>>>> [ 2.142303] [0x1c]:0001285c >>>>> [ 2.142477] [0x20]:14000400 >>>>> [ 2.142651] [0x24]:00000020 >>>>> [ 2.142825] [0x28]:0100000f >>>>> [ 2.143000] [0x2c]:000c000b >>>>> [ 2.143174] [0x30]:003c0003 >>>>> [ 2.143349] [0x34]:0020ffe0 >>>>> [ 2.143544] [0x38]:00800122 >>>>> [ 2.143719] [0x3c]:00000009 >>>>> [ 2.143895] mpt2sas_cm0: hba queue depth(3432), max chains per io(128) >>>>> [ 2.144106] mpt2sas_cm0: request frame size(128), reply frame size(128) >>>>> [ 2.144397] mpt2sas_cm0: msix is supported, vector_count(1) >>>>> [ 2.144600] mpt2sas_cm0: MSI-X vectors supported: 1, no of cores: 4, max_msix_vectors: -1 >>>>> [ 2.145161] mpt2sas0-msix0: PCI-MSI-X enabled: IRQ 58 >>>>> [ 2.145361] mpt2sas_cm0: iomem(0x00000000fd4fc000), mapped(0xffffc900000d0000), size(16384) >>>>> [ 2.145591] mpt2sas_cm0: ioport(0x0000000000004000), size(256) >>>>> [ 2.146206] mpt2sas_cm0: _base_get_ioc_facts >>>>> [ 2.146397] mpt2sas_cm0: _base_wait_for_iocstate >>>>> [ 2.202087] offset:data >>>>> [ 2.202281] [0x00]:03100200 >>>>> [ 2.202456] [0x04]:00002300 >>>>> [ 2.202631] [0x08]:00000000 >>>>> [ 2.202805] [0x0c]:00000000 >>>>> [ 2.202980] [0x10]:00000000 >>>>> [ 2.203154] [0x14]:00010480 >>>>> [ 2.203328] [0x18]:22130d68 >>>>> [ 2.203521] [0x1c]:0001285c >>>>> [ 2.203695] [0x20]:14000400 >>>>> [ 2.203870] [0x24]:00000020 >>>>> [ 2.204044] [0x28]:0100000f >>>>> [ 2.204219] [0x2c]:000c000b >>>>> [ 2.204394] [0x30]:003c0003 >>>>> [ 2.204571] [0x34]:0020ffe0 >>>>> [ 2.204746] [0x38]:00800122 >>>>> [ 2.204926] [0x3c]:00000009 >>>>> [ 2.205102] mpt2sas_cm0: hba queue depth(3432), max chains per io(128) >>>>> [ 2.205314] mpt2sas_cm0: request frame size(128), reply frame size(128) >>>>> [ 2.205528] mpt2sas_cm0: _base_make_ioc_ready >>>>> [ 2.205719] mpt2sas_cm0: _base_get_port_facts >>>>> [ 2.234205] offset:data >>>>> [ 2.234397] [0x00]:05070000 >>>>> [ 2.234573] [0x04]:00000000 >>>>> [ 2.234748] [0x08]:00000000 >>>>> [ 2.234928] [0x0c]:00000000 >>>>> [ 2.235103] [0x10]:00000000 >>>>> [ 2.235278] [0x14]:00003000 >>>>> [ 2.235453] [0x18]:00000078 >>>>> [ 2.235629] mpt2sas_cm0: _base_allocate_memory_pools >>>>> [ 2.235826] mpt2sas_cm0: scatter gather: sge_in_main_msg(3), sge_per_chain(15), sge_per_io(128), chains_per_io(9) >>>>> [ 2.236227] mpt2sas_cm0: reply post free pool (0xffff8800bb380000): depth(6944),element_size(8), pool_size(54 kB) >>>>> [ 2.236611] mpt2sas_cm0: reply_post_free_dma = (0xbb380000) >>>>> [ 2.236813] mpt2sas_cm0: scsi host: can_queue depth (3307) >>>>> [ 2.237086] mpt2sas_cm0: request pool(0xffff8800ba880000): depth(3432), frame_size(128), pool_size(429 kB) >>>>> [ 2.238580] mpt2sas_cm0: request pool: dma(0xba880000) >>>>> [ 2.238781] mpt2sas_cm0: scsiio(0xffff8800ba880000): depth(3307) >>>>> [ 2.243644] mpt2sas_cm0: chain pool depth(29763), frame_size(128), pool_size(3720 kB) >>>>> [ 2.243887] mpt2sas_cm0: hi_priority(0xffff8800ba8e7600): depth(60), start smid(3308) >>>>> [ 2.244113] mpt2sas_cm0: internal(0xffff8800ba8e9400): depth(65), start smid(3368) >>>>> [ 2.244390] mpt2sas_cm0: sense pool(0xffff8800ba480000): depth(3307), element_size(96), pool_size(310 kB) >>>>> [ 2.244774] mpt2sas_cm0: sense_dma(0xba480000) >>>>> [ 2.245038] mpt2sas_cm0: reply pool(0xffff8800ba500000): depth(3496), frame_size(128), pool_size(437 kB) >>>>> [ 2.245413] mpt2sas_cm0: reply_dma(0xba500000) >>>>> [ 2.245608] mpt2sas_cm0: reply_free pool(0xffff8800ba430000): depth(3496), element_size(4), pool_size(13 kB) >>>>> [ 2.245985] mpt2sas_cm0: reply_free_dma (0xba430000) >>>>> [ 2.246181] mpt2sas_cm0: config page(0xffff8800ba429000): size(512) >>>>> [ 2.246389] mpt2sas_cm0: config_page_dma(0xba429000) >>>>> [ 2.246584] mpt2sas_cm0: Allocated physical memory: size(4964 kB) >>>>> [ 2.246791] mpt2sas_cm0: Current Controller Queue Depth(3307),Max Controller Queue Depth(3432) >>>>> [ 2.247155] mpt2sas_cm0: Scatter Gather Elements per IO(128) >>>>> [ 2.247361] mpt2sas_cm0: _base_make_ioc_operational >>>>> [ 2.247962] mpt2sas_cm0: _base_send_ioc_init >>>>> [ 2.248154] offset:data >>>>> [ 2.248325] [0x00]:02000004 >>>>> [ 2.248499] [0x04]:00000000 >>>>> [ 2.248673] [0x08]:00000000 >>>>> [ 2.248848] [0x0c]:23000200 >>>>> [ 2.249023] [0x10]:00000000 >>>>> [ 2.249197] [0x14]:00000000 >>>>> [ 2.249372] [0x18]:00200000 >>>>> [ 2.249546] [0x1c]:0da81b20 >>>>> [ 2.249720] [0x20]:00000000 >>>>> [ 2.249894] [0x24]:00000000 >>>>> [ 2.250068] [0x28]:ba880000 >>>>> [ 2.250242] [0x2c]:00000000 >>>>> [ 2.250416] [0x30]:bb380000 >>>>> [ 2.250589] [0x34]:00000000 >>>>> [ 2.250768] [0x38]:ba430000 >>>>> [ 2.250941] [0x3c]:00000000 >>>>> [ 2.251115] [0x40]:983eb686 >>>>> [ 2.251288] [0x44]:00000153 >>>>> [ 2.296610] offset:data >>>>> [ 2.296795] [0x00]:02050004 >>>>> [ 2.296969] [0x04]:00000000 >>>>> [ 2.297143] [0x08]:00000000 >>>>> [ 2.297318] [0x0c]:00000000 >>>>> [ 2.297493] [0x10]:00000000 >>>>> [ 2.297668] mpt2sas_cm0: _base_event_notification >>>>> [ 5.093707] floppy0: no floppy controllers found >>>>> [ 32.293619] mpt2sas_cm0: _base_event_notification: timeout >>>>> [ 32.293909] mf: >>>>> >>>>> [ 32.294132] 07000000 >>>>> [ 32.294397] 00000000 >>>>> [ 32.294445] 00000000 >>>>> [ 32.294719] 00000000 >>>>> [ 32.294767] 00000000 >>>>> [ 32.295031] 0f2f7fff >>>>> [ 32.295078] ffffff7c >>>>> [ 32.295342] ffffffff >>>>> [ 32.295389] >>>>> >>>>> [ 32.295823] ffffffff >>>>> [ 32.295871] 00000000 >>>>> [ 32.296134] 00000000 >>>>> >>>>> [ 32.296615] mpt2sas_cm0: mpt3sas_base_free_resources >>>>> [ 32.296880] mpt2sas_cm0: _base_make_ioc_ready >>>>> [ 32.297135] mpt2sas_cm0: sending message unit reset !! >>>>> [ 32.298941] mpt2sas_cm0: message unit reset: SUCCESS >>>>> [ 32.299212] mpt2sas_cm0: mpt3sas_base_unmap_resources >>>>> [ 32.300381] mpt2sas_cm0: _base_release_memory_pools >>>>> [ 32.300654] mpt2sas_cm0: request_pool(0xffff8800ba880000): free >>>>> [ 32.300934] mpt2sas_cm0: sense_pool(0xffff8800ba480000): free >>>>> [ 32.301211] mpt2sas_cm0: reply_pool(0xffff8800ba500000): free >>>>> [ 32.301485] mpt2sas_cm0: reply_free_pool(0xffff8800ba430000): free >>>>> [ 32.301774] mpt2sas_cm0: reply_post_free_pool(0xffff8800bb380000): free >>>>> [ 32.302061] mpt2sas_cm0: config_page(0xffff8800ba429000): free >>>>> [ 32.371097] mpt2sas_cm0: failure at drivers/scsi/mpt3sas/mpt3sas_scsih.c:8592/_scsih_probe()! >>>>> [ 32.371958] mpt2sas_cm1: mpt3sas_base_attach >>>>> [ 32.372154] mpt2sas_cm1: mpt3sas_base_map_resources >>>>> [ 32.372950] mpt2sas_cm1: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3074748 kB) >>>>> [ 32.373201] mpt2sas_cm1: _base_get_ioc_facts >>>>> [ 32.375261] mpt2sas_cm1: _base_wait_for_iocstate >>>>> [ 32.432012] offset:data >>>>> [ 32.432262] [0x00]:03100200 >>>>> [ 32.432499] [0x04]:00002300 >>>>> [ 32.432735] [0x08]:00000000 >>>>> [ 32.432971] [0x0c]:00000000 >>>>> [ 32.433206] [0x10]:00000000 >>>>> [ 32.433443] [0x14]:00010480 >>>>> [ 32.433701] [0x18]:22130d68 >>>>> [ 32.433937] [0x1c]:0001285c >>>>> [ 32.435434] [0x20]:14000400 >>>>> [ 32.435674] [0x24]:00000020 >>>>> [ 32.435909] [0x28]:0100000f >>>>> [ 32.436144] [0x2c]:000c000b >>>>> [ 32.436379] [0x30]:003c0003 >>>>> [ 32.436615] [0x34]:0020ffe0 >>>>> [ 32.436850] [0x38]:00800122 >>>>> [ 32.437085] [0x3c]:00000009 >>>>> [ 32.437322] mpt2sas_cm1: hba queue depth(3432), max chains per io(128) >>>>> [ 32.437607] mpt2sas_cm1: request frame size(128), reply frame size(128) >>>>> [ 32.438014] mpt2sas_cm1: msix is supported, vector_count(1) >>>>> [ 32.438288] mpt2sas_cm1: MSI-X vectors supported: 1, no of cores: 4, max_msix_vectors: 8 >>>>> [ 32.439101] mpt2sas1-msix0: PCI-MSI-X enabled: IRQ 58 >>>>> [ 32.439373] mpt2sas_cm1: iomem(0x00000000fd1fc000), mapped(0xffffc900000d8000), size(16384) >>>>> [ 32.439682] mpt2sas_cm1: ioport(0x0000000000007000), size(256) >>>>> [ 32.440504] mpt2sas_cm1: _base_get_ioc_facts >>>>> [ 32.440765] mpt2sas_cm1: _base_wait_for_iocstate >>>>> [ 32.499305] offset:data >>>>> [ 32.499557] [0x00]:03100200 >>>>> [ 32.499794] [0x04]:00002300 >>>>> [ 32.500031] [0x08]:00000000 >>>>> [ 32.500267] [0x0c]:00000000 >>>>> [ 32.500504] [0x10]:00000000 >>>>> [ 32.500740] [0x14]:00010480 >>>>> [ 32.500974] [0x18]:22130d68 >>>>> [ 32.501209] [0x1c]:0001285c >>>>> [ 32.501444] [0x20]:14000400 >>>>> [ 32.501687] [0x24]:00000020 >>>>> [ 32.501922] [0x28]:0100000f >>>>> [ 32.502157] [0x2c]:000c000b >>>>> [ 32.502391] [0x30]:003c0003 >>>>> [ 32.502626] [0x34]:0020ffe0 >>>>> [ 32.502862] [0x38]:00800122 >>>>> [ 32.503098] [0x3c]:00000009 >>>>> [ 32.503336] mpt2sas_cm1: hba queue depth(3432), max chains per io(128) >>>>> [ 32.503644] mpt2sas_cm1: request frame size(128), reply frame size(128) >>>>> [ 32.503933] mpt2sas_cm1: _base_make_ioc_ready >>>>> [ 32.504191] mpt2sas_cm1: _base_get_port_facts >>>>> [ 32.534282] offset:data >>>>> [ 32.534537] [0x00]:05070000 >>>>> [ 32.534782] [0x04]:00000000 >>>>> [ 32.535058] [0x08]:00000000 >>>>> [ 32.536473] [0x0c]:00000000 >>>>> [ 32.536710] [0x10]:00000000 >>>>> [ 32.536946] [0x14]:00003000 >>>>> [ 32.537183] [0x18]:00000078 >>>>> [ 32.537420] mpt2sas_cm1: _base_allocate_memory_pools >>>>> [ 32.537686] mpt2sas_cm1: scatter gather: sge_in_main_msg(3), sge_per_chain(15), sge_per_io(128), chains_per_io(9) >>>>> [ 32.538232] mpt2sas_cm1: reply post free pool (0xffff8800bb3d0000): depth(6944),element_size(8), pool_size(54 kB) >>>>> [ 32.538758] mpt2sas_cm1: reply_post_free_dma = (0xbb3d0000) >>>>> [ 32.539030] mpt2sas_cm1: scsi host: can_queue depth (3307) >>>>> [ 32.539378] mpt2sas_cm1: request pool(0xffff8800ba480000): depth(3432), frame_size(128), pool_size(429 kB) >>>>> [ 32.539882] mpt2sas_cm1: request pool: dma(0xba480000) >>>>> [ 32.540149] mpt2sas_cm1: scsiio(0xffff8800ba480000): depth(3307) >>>>> [ 32.545893] mpt2sas_cm1: chain pool depth(29763), frame_size(128), pool_size(3720 kB) >>>>> [ 32.546137] mpt2sas_cm1: hi_priority(0xffff8800ba4e7600): depth(60), start smid(3308) >>>>> [ 32.546365] mpt2sas_cm1: internal(0xffff8800ba4e9400): depth(65), start smid(3368) >>>>> [ 32.546651] mpt2sas_cm1: sense pool(0xffff8800ba880000): depth(3307), element_size(96), pool_size(310 kB) >>>>> [ 32.547030] mpt2sas_cm1: sense_dma(0xba880000) >>>>> [ 32.547537] mpt2sas_cm1: reply pool(0xffff880000100000): depth(3496), frame_size(128), pool_size(437 kB) >>>>> [ 32.547921] mpt2sas_cm1: reply_dma(0x100000) >>>>> [ 32.548117] mpt2sas_cm1: reply_free pool(0xffff8800ba964000): depth(3496), element_size(4), pool_size(13 kB) >>>>> [ 32.548500] mpt2sas_cm1: reply_free_dma (0xba964000) >>>>> [ 32.548698] mpt2sas_cm1: config page(0xffff8800ba960000): size(512) >>>>> [ 32.548908] mpt2sas_cm1: config_page_dma(0xba960000) >>>>> [ 32.549105] mpt2sas_cm1: Allocated physical memory: size(4964 kB) >>>>> [ 32.549314] mpt2sas_cm1: Current Controller Queue Depth(3307),Max Controller Queue Depth(3432) >>>>> [ 32.550950] mpt2sas_cm1: Scatter Gather Elements per IO(128) >>>>> [ 32.551160] mpt2sas_cm1: _base_make_ioc_operational >>>>> [ 32.551855] mpt2sas_cm1: _base_send_ioc_init >>>>> [ 32.552051] offset:data >>>>> [ 32.552224] [0x00]:02000004 >>>>> [ 32.552400] [0x04]:00000000 >>>>> [ 32.552576] [0x08]:00000000 >>>>> [ 32.552761] [0x0c]:23000200 >>>>> [ 32.552937] [0x10]:00000000 >>>>> [ 32.553114] [0x14]:00000000 >>>>> [ 32.553291] [0x18]:00200000 >>>>> [ 32.553468] [0x1c]:0da81b20 >>>>> [ 32.553685] [0x20]:00000000 >>>>> [ 32.553862] [0x24]:00000000 >>>>> [ 32.554038] [0x28]:ba480000 >>>>> [ 32.554215] [0x2c]:00000000 >>>>> [ 32.554393] [0x30]:bb3d0000 >>>>> [ 32.554569] [0x34]:00000000 >>>>> [ 32.554752] [0x38]:ba964000 >>>>> [ 32.554929] [0x3c]:00000000 >>>>> [ 32.555106] [0x40]:983f2ce6 >>>>> [ 32.555283] [0x44]:00000153 >>>>> [ 32.601516] offset:data >>>>> [ 32.601768] [0x00]:02050004 >>>>> [ 32.602003] [0x04]:00000000 >>>>> [ 32.602239] [0x08]:00000000 >>>>> [ 32.602474] [0x0c]:00000000 >>>>> [ 32.602709] [0x10]:00000000 >>>>> [ 32.602945] mpt2sas_cm1: _base_event_notification >>>>> [ 62.593604] mpt2sas_cm1: _base_event_notification: timeout >>>>> [ 62.593906] mf: >>>>> >>>>> [ 62.594127] 07000000 >>>>> [ 62.594390] 00000000 >>>>> [ 62.594438] 00000000 >>>>> [ 62.594709] 00000000 >>>>> [ 62.594757] 00000000 >>>>> [ 62.595019] 0f2f7fff >>>>> [ 62.595067] ffffff7c >>>>> [ 62.595330] ffffffff >>>>> [ 62.595377] >>>>> >>>>> [ 62.595808] ffffffff >>>>> [ 62.595855] 00000000 >>>>> [ 62.596117] 00000000 >>>>> >>>>> [ 62.596601] mpt2sas_cm1: mpt3sas_base_free_resources >>>>> [ 62.596871] mpt2sas_cm1: _base_make_ioc_ready >>>>> [ 62.597125] mpt2sas_cm1: sending message unit reset !! >>>>> [ 62.599013] mpt2sas_cm1: message unit reset: SUCCESS >>>>> [ 62.599283] mpt2sas_cm1: mpt3sas_base_unmap_resources >>>>> [ 62.600443] mpt2sas_cm1: _base_release_memory_pools >>>>> [ 62.600721] mpt2sas_cm1: request_pool(0xffff8800ba480000): free >>>>> [ 62.601002] mpt2sas_cm1: sense_pool(0xffff8800ba880000): free >>>>> [ 62.601280] mpt2sas_cm1: reply_pool(0xffff880000100000): free >>>>> [ 62.601560] mpt2sas_cm1: reply_free_pool(0xffff8800ba964000): free >>>>> [ 62.601845] mpt2sas_cm1: reply_post_free_pool(0xffff8800bb3d0000): free >>>>> [ 62.602133] mpt2sas_cm1: config_page(0xffff8800ba960000): free >>>>> [ 62.673591] mpt2sas_cm1: failure at drivers/scsi/mpt3sas/mpt3sas_scsih.c:8592/_scsih_probe()! >>>> >>>> These are for two controllers, I don't know whether the output from the >>>> second is helpful at all - I added it anyway. >>>> >>>> >>>> I managed to boot the same 4.5.0 kernel successfully after warm >>>> rebooting from 4.1.20. That gave me this dmesg output (for comparison): >>>> >>>>> [ 2.057685] mpt3sas version 09.102.00.00 loaded >>>>> [ 2.058371] mpt2sas_cm0: mpt3sas_base_attach >>>>> [ 2.058632] mpt2sas_cm0: mpt3sas_base_map_resources >>>>> [ 2.059583] mpt2sas_cm0: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3074748 kB) >>>>> [ 2.059911] mpt2sas_cm0: _base_get_ioc_facts >>>>> [ 2.060166] mpt2sas_cm0: _base_wait_for_iocstate >>>>> [ 2.116337] offset:data >>>>> [ 2.116576] [0x00]:03100200 >>>>> [ 2.116817] [0x04]:00002300 >>>>> [ 2.117051] [0x08]:00000000 >>>>> [ 2.117285] [0x0c]:00000000 >>>>> [ 2.117518] [0x10]:00000000 >>>>> [ 2.117752] [0x14]:00010480 >>>>> [ 2.117986] [0x18]:22130d68 >>>>> [ 2.118220] [0x1c]:0001285c >>>>> [ 2.119624] [0x20]:14000400 >>>>> [ 2.119858] [0x24]:00000020 >>>>> [ 2.120093] [0x28]:0100000f >>>>> [ 2.120351] [0x2c]:000c000b >>>>> [ 2.120586] [0x30]:003c0003 >>>>> [ 2.120820] [0x34]:0020ffe0 >>>>> [ 2.121055] [0x38]:00800122 >>>>> [ 2.121288] [0x3c]:00000009 >>>>> [ 2.121524] mpt2sas_cm0: hba queue depth(3432), max chains per io(128) >>>>> [ 2.121808] mpt2sas_cm0: request frame size(128), reply frame size(128) >>>>> [ 2.122195] mpt2sas_cm0: msix is supported, vector_count(1) >>>>> [ 2.122468] mpt2sas_cm0: MSI-X vectors supported: 1, no of cores: 4, max_msix_vectors: -1 >>>>> [ 2.123239] mpt2sas0-msix0: PCI-MSI-X enabled: IRQ 58 >>>>> [ 2.123507] mpt2sas_cm0: iomem(0x00000000fd4fc000), mapped(0xffffc900000d0000), size(16384) >>>>> [ 2.123816] mpt2sas_cm0: ioport(0x0000000000004000), size(256) >>>>> [ 2.124623] mpt2sas_cm0: _base_get_ioc_facts >>>>> [ 2.124878] mpt2sas_cm0: _base_wait_for_iocstate >>>>> [ 2.180907] offset:data >>>>> [ 2.181145] [0x00]:03100200 >>>>> [ 2.181379] [0x04]:00002300 >>>>> [ 2.181613] [0x08]:00000000 >>>>> [ 2.181847] [0x0c]:00000000 >>>>> [ 2.182081] [0x10]:00000000 >>>>> [ 2.182315] [0x14]:00010480 >>>>> [ 2.182547] [0x18]:22130d68 >>>>> [ 2.182781] [0x1c]:0001285c >>>>> [ 2.183014] [0x20]:14000400 >>>>> [ 2.183248] [0x24]:00000020 >>>>> [ 2.183481] [0x28]:0100000f >>>>> [ 2.183720] [0x2c]:000c000b >>>>> [ 2.183954] [0x30]:003c0003 >>>>> [ 2.184190] [0x34]:0020ffe0 >>>>> [ 2.184424] [0x38]:00800122 >>>>> [ 2.184658] [0x3c]:00000009 >>>>> [ 2.184893] mpt2sas_cm0: hba queue depth(3432), max chains per io(128) >>>>> [ 2.185177] mpt2sas_cm0: request frame size(128), reply frame size(128) >>>>> [ 2.185462] mpt2sas_cm0: _base_make_ioc_ready >>>>> [ 2.185717] mpt2sas_cm0: _base_get_port_facts >>>>> [ 2.214057] offset:data >>>>> [ 2.214295] [0x00]:05070000 >>>>> [ 2.214529] [0x04]:00000000 >>>>> [ 2.214762] [0x08]:00000000 >>>>> [ 2.214997] [0x0c]:00000000 >>>>> [ 2.215230] [0x10]:00000000 >>>>> [ 2.215464] [0x14]:00003000 >>>>> [ 2.215697] [0x18]:00000078 >>>>> [ 2.215931] mpt2sas_cm0: _base_allocate_memory_pools >>>>> [ 2.216194] mpt2sas_cm0: scatter gather: sge_in_main_msg(3), sge_per_chain(15), sge_per_io(128), chains_per_io(9) >>>>> [ 2.216734] mpt2sas_cm0: reply post free pool (0xffff8800bafc0000): depth(6944),element_size(8), pool_size(54 kB) >>>>> [ 2.217244] mpt2sas_cm0: reply_post_free_dma = (0xbafc0000) >>>>> [ 2.217514] mpt2sas_cm0: scsi host: can_queue depth (3307) >>>>> [ 2.217866] mpt2sas_cm0: request pool(0xffff8800ba800000): depth(3432), frame_size(128), pool_size(429 kB) >>>>> [ 2.218369] mpt2sas_cm0: request pool: dma(0xba800000) >>>>> [ 2.218637] mpt2sas_cm0: scsiio(0xffff8800ba800000): depth(3307) >>>>> [ 2.224773] mpt2sas_cm0: chain pool depth(29763), frame_size(128), pool_size(3720 kB) >>>>> [ 2.225092] mpt2sas_cm0: hi_priority(0xffff8800ba867600): depth(60), start smid(3308) >>>>> [ 2.225395] mpt2sas_cm0: internal(0xffff8800ba869400): depth(65), start smid(3368) >>>>> [ 2.225958] mpt2sas_cm0: sense pool(0xffff8800ba480000): depth(3307), element_size(96), pool_size(310 kB) >>>>> [ 2.226457] mpt2sas_cm0: sense_dma(0xba480000) >>>>> [ 2.227039] mpt2sas_cm0: reply pool(0xffff8800ba500000): depth(3496), frame_size(128), pool_size(437 kB) >>>>> [ 2.227413] mpt2sas_cm0: reply_dma(0xba500000) >>>>> [ 2.227616] mpt2sas_cm0: reply_free pool(0xffff8800ba450000): depth(3496), element_size(4), pool_size(13 kB) >>>>> [ 2.227992] mpt2sas_cm0: reply_free_dma (0xba450000) >>>>> [ 2.228192] mpt2sas_cm0: config page(0xffff8800ba43b000): size(512) >>>>> [ 2.228402] mpt2sas_cm0: config_page_dma(0xba43b000) >>>>> [ 2.228598] mpt2sas_cm0: Allocated physical memory: size(4964 kB) >>>>> [ 2.228806] mpt2sas_cm0: Current Controller Queue Depth(3307),Max Controller Queue Depth(3432) >>>>> [ 2.229171] mpt2sas_cm0: Scatter Gather Elements per IO(128) >>>>> [ 2.229378] mpt2sas_cm0: _base_make_ioc_operational >>>>> [ 2.229959] mpt2sas_cm0: _base_send_ioc_init >>>>> [ 2.230151] offset:data >>>>> [ 2.230323] [0x00]:02000004 >>>>> [ 2.230499] [0x04]:00000000 >>>>> [ 2.230675] [0x08]:00000000 >>>>> [ 2.230851] [0x0c]:23000200 >>>>> [ 2.231026] [0x10]:00000000 >>>>> [ 2.231201] [0x14]:00000000 >>>>> [ 2.231376] [0x18]:00200000 >>>>> [ 2.231551] [0x1c]:0da81b20 >>>>> [ 2.231726] [0x20]:00000000 >>>>> [ 2.231900] [0x24]:00000000 >>>>> [ 2.232075] [0x28]:ba800000 >>>>> [ 2.232250] [0x2c]:00000000 >>>>> [ 2.232423] [0x30]:bafc0000 >>>>> [ 2.232597] [0x34]:00000000 >>>>> [ 2.232775] [0x38]:ba450000 >>>>> [ 2.232950] [0x3c]:00000000 >>>>> [ 2.233125] [0x40]:98596e4f >>>>> [ 2.233299] [0x44]:00000153 >>>>> [ 2.278752] offset:data >>>>> [ 2.278988] [0x00]:02050004 >>>>> [ 2.279220] [0x04]:00000000 >>>>> [ 2.279453] [0x08]:00000000 >>>>> [ 2.279685] [0x0c]:00000000 >>>>> [ 2.279918] [0x10]:00000000 >>>>> [ 2.280151] mpt2sas_cm0: _base_event_notification >>>>> [ 2.280537] mpt2sas_cm0: _base_event_notification: complete >>>>> [ 2.281694] mpt2sas_cm0: LSISAS2008: FWVersion(20.00.04.00), ChipRevision(0x03), BiosVersion(07.39.00.00) >>>>> [ 2.282196] mpt2sas_cm0: Protocol=( >>>>> [ 2.282261] Initiator >>>>> [ 2.282522] ,Target >>>>> [ 2.282567] ), >>>>> [ 2.282824] Capabilities=( >>>>> [ 2.282877] TLR >>>>> [ 2.283132] ,EEDP >>>>> [ 2.283175] ,Snapshot Buffer >>>>> [ 2.283444] ,Diag Trace Buffer >>>>> [ 2.283502] ,Task Set Full >>>>> [ 2.283774] ,NCQ >>>>> [ 2.283816] ) >>>>> [ 2.284350] scsi host0: Fusion MPT SAS Host >>>>> [ 2.299028] mpt2sas_cm0: sending port enable !! >>>>> [ 2.299540] mpt2sas_cm0: Discovery: (start) >>>>> >>>>> [ 2.299972] mpt2sas_cm0: SAS Enclosure Device Status Change >>>>> [ 2.299984] mpt2sas_cm0: discovery event: (start) >>>>> >>>>> [ 2.300554] mpt2sas_cm0: SAS Topology Change List >>>>> [ 2.300759] mpt2sas_cm0: Discovery: (stop) >>>>> >>>>> [ 2.301146] mpt2sas_cm0: Discovery: (start) >>>>> >>>>> [ 2.301535] mpt2sas_cm0: Discovery: (stop) >>>>> >>>>> [ 2.301927] mpt2sas_cm0: Discovery: (start) >>>>> >>>>> [ 2.302316] mpt2sas_cm0: Discovery: (stop) >>>>> >>>>> [ 2.302707] mpt2sas_cm0: Discovery: (start) >>>>> >>>>> [ 2.304908] mpt2sas_cm0: Discovery: (stop) >>>>> >>>>> [ 2.305297] mpt2sas_cm0: Discovery: (start) >>>>> >>>>> [ 2.306776] mpt2sas_cm0: Discovery: (stop) >>>>> >>>>> [ 2.307166] mpt2sas_cm0: Discovery: (start) >>>>> >>>>> [ 2.307559] mpt2sas_cm0: Discovery: (stop) >>>>> >>>>> [ 2.307948] mpt2sas_cm0: Discovery: (start) >>>>> >>>>> [ 2.308336] mpt2sas_cm0: Discovery: (stop) >>>>> >>>>> [ 2.311738] mpt2sas_cm0: host_add: handle(0x0001), sas_addr(0x500605b003683dd0), phys(8) >>>>> [ 2.312097] mpt2sas_cm0: enclosure status change: (enclosure add) >>>>> handle(0x0001), enclosure logical id(0x500605b003683dd0) number slots(0) >>>>> [ 2.312551] mpt2sas_cm0: sas topology change: (responding) >>>>> [ 2.312768] handle(0x0000), enclosure_handle(0x0001) start_phy(00), count(8) >>>>> [ 2.313003] phy(01), attached_handle(0x0009): target add: link rate: new(0x0a), old(0x00) >>>>> [ 2.313250] phy(02), attached_handle(0x000a): target add: link rate: new(0x09), old(0x00) >>>>> [ 2.313498] phy(03), attached_handle(0x000b): target add: link rate: new(0x09), old(0x00) >>>>> [ 2.313745] phy(04), attached_handle(0x000c): target add: link rate: new(0x09), old(0x00) >>>>> [ 2.313992] phy(05), attached_handle(0x000d): target add: link rate: new(0x09), old(0x00) >>>>> [ 2.314248] phy(06), attached_handle(0x000e): target add: link rate: new(0x09), old(0x00) >>>>> [ 2.314495] phy(07), attached_handle(0x000f): target add: link rate: new(0x09), old(0x00) >>>>> [ 2.314747] mpt2sas_cm0: updating handles for sas_host(0x500605b003683dd0) >>>>> [ 2.316041] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x0009), sas_addr(0x4433221101000000) >>>>> [ 2.316465] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 2) >>>>> [ 2.317200] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000a), sas_addr(0x4433221102000000) >>>>> [ 2.317669] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 1) >>>>> [ 2.318431] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000b), sas_addr(0x4433221103000000) >>>>> [ 2.318900] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 0) >>>>> [ 2.319366] mpt2sas_cm0: _scsih_determine_boot_device: current_boot_device(0x4433221103000000) >>>>> [ 2.320151] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000c), sas_addr(0x4433221104000000) >>>>> [ 2.321371] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 7) >>>>> [ 2.322137] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000d), sas_addr(0x4433221105000000) >>>>> [ 2.322606] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 6) >>>>> [ 2.323367] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000e), sas_addr(0x4433221106000000) >>>>> [ 2.323834] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 5) >>>>> [ 2.324602] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000f), sas_addr(0x4433221107000000) >>>>> [ 2.325071] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 4) >>>>> [ 2.325541] mpt2sas_cm0: discovery event: (stop) >>>>> >>>>> [ 2.326017] mpt2sas_cm0: discovery event: (start) >>>>> >>>>> [ 2.326492] mpt2sas_cm0: discovery event: (stop) >>>>> >>>>> [ 2.326975] mpt2sas_cm0: discovery event: (start) >>>>> >>>>> [ 2.327450] mpt2sas_cm0: discovery event: (stop) >>>>> >>>>> [ 2.327923] mpt2sas_cm0: discovery event: (start) >>>>> >>>>> [ 2.328396] mpt2sas_cm0: discovery event: (stop) >>>>> >>>>> [ 2.328868] mpt2sas_cm0: discovery event: (start) >>>>> >>>>> [ 2.329340] mpt2sas_cm0: discovery event: (stop) >>>>> >>>>> [ 2.329816] mpt2sas_cm0: discovery event: (start) >>>>> >>>>> [ 2.330316] mpt2sas_cm0: discovery event: (stop) >>>>> >>>>> [ 2.330797] mpt2sas_cm0: discovery event: (start) >>>>> >>>>> [ 2.331269] mpt2sas_cm0: discovery event: (stop) >>>>> >>>>> [ 2.331740] mpt2sas_cm0: port enable: complete from worker thread >>>>> [ 2.350236] mpt2sas_cm0: port enable: SUCCESS >>>>> [ 2.356432] scsi 0:0:0:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 >>>>> [ 2.356683] scsi 0:0:0:0: SATA: handle(0x000b), sas_addr(0x4433221103000000), phy(3), device_name(0x5000c5000267c9f8) >>>>> [ 2.357080] scsi 0:0:0:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(0) >>>>> [ 2.357405] scsi 0:0:0:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>> [ 2.383043] scsi 0:0:1:0: Direct-Access ATA Hitachi HDS5C302 A800 PQ: 0 ANSI: 6 >>>>> [ 2.383296] scsi 0:0:1:0: SATA: handle(0x0009), sas_addr(0x4433221101000000), phy(1), device_name(0x5000cca369cdd311) >>>>> [ 2.383684] scsi 0:0:1:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(2) >>>>> [ 2.384028] scsi 0:0:1:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>> [ 2.405088] scsi 0:0:2:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 >>>>> [ 2.405346] scsi 0:0:2:0: SATA: handle(0x000a), sas_addr(0x4433221102000000), phy(2), device_name(0x5000c5000ccfbd32) >>>>> [ 2.405735] scsi 0:0:2:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(1) >>>>> [ 2.406082] scsi 0:0:2:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>> [ 2.424125] scsi 0:0:3:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 >>>>> [ 2.424373] scsi 0:0:3:0: SATA: handle(0x000c), sas_addr(0x4433221104000000), phy(4), device_name(0x5000c5000267abee) >>>>> [ 2.424763] scsi 0:0:3:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(7) >>>>> [ 2.425108] scsi 0:0:3:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>> [ 2.444834] scsi 0:0:4:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 >>>>> [ 2.445086] scsi 0:0:4:0: SATA: handle(0x000d), sas_addr(0x4433221105000000), phy(5), device_name(0x5000c50009c0e5e6) >>>>> [ 2.445478] scsi 0:0:4:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(6) >>>>> [ 2.445803] scsi 0:0:4:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>> [ 2.464065] scsi 0:0:5:0: Direct-Access ATA ST3750330NS SN16 PQ: 0 ANSI: 6 >>>>> [ 2.464312] scsi 0:0:5:0: SATA: handle(0x000e), sas_addr(0x4433221106000000), phy(6), device_name(0x5000c5003cb9ac10) >>>>> [ 2.464699] scsi 0:0:5:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(5) >>>>> [ 2.465048] scsi 0:0:5:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>> [ 2.484016] scsi 0:0:6:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 >>>>> [ 2.484266] scsi 0:0:6:0: SATA: handle(0x000f), sas_addr(0x4433221107000000), phy(7), device_name(0x5000c5000839b69e) >>>>> [ 2.484655] scsi 0:0:6:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(4) >>>>> [ 2.485001] scsi 0:0:6:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>> [ 2.500660] mpt2sas_cm1: mpt3sas_base_attach >>>>> [ 2.500861] mpt2sas_cm1: mpt3sas_base_map_resources >>>>> [ 2.501599] mpt2sas_cm1: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3074748 kB) >>>>> [ 2.501847] mpt2sas_cm1: _base_get_ioc_facts >>>>> [ 2.502036] mpt2sas_cm1: _base_wait_for_iocstate >>>>> [ 2.559080] offset:data >>>>> [ 2.559318] [0x00]:03100200 >>>>> [ 2.559552] [0x04]:00002300 >>>>> [ 2.559785] [0x08]:00000000 >>>>> [ 2.560020] [0x0c]:00000000 >>>>> [ 2.560277] [0x10]:00000000 >>>>> [ 2.560511] [0x14]:00010480 >>>>> [ 2.560745] [0x18]:22130d68 >>>>> [ 2.560978] [0x1c]:0001285c >>>>> [ 2.561210] [0x20]:14000400 >>>>> [ 2.561443] [0x24]:00000020 >>>>> [ 2.561675] [0x28]:0100000f >>>>> [ 2.561907] [0x2c]:000c000b >>>>> [ 2.562139] [0x30]:003c0003 >>>>> [ 2.562371] [0x34]:0020ffe0 >>>>> [ 2.562602] [0x38]:00800122 >>>>> [ 2.562839] [0x3c]:00000009 >>>>> [ 2.563073] mpt2sas_cm1: hba queue depth(3432), max chains per io(128) >>>>> [ 2.563355] mpt2sas_cm1: request frame size(128), reply frame size(128) >>>>> [ 2.563745] mpt2sas_cm1: msix is supported, vector_count(1) >>>>> [ 2.564016] mpt2sas_cm1: MSI-X vectors supported: 1, no of cores: 4, max_msix_vectors: 8 >>>>> [ 2.564918] mpt2sas1-msix0: PCI-MSI-X enabled: IRQ 59 >>>>> [ 2.566189] mpt2sas_cm1: iomem(0x00000000fd1fc000), mapped(0xffffc900000d8000), size(16384) >>>>> [ 2.566498] mpt2sas_cm1: ioport(0x0000000000007000), size(256) >>>>> [ 2.567328] mpt2sas_cm1: _base_get_ioc_facts >>>>> [ 2.567583] mpt2sas_cm1: _base_wait_for_iocstate >>>>> [ 2.625125] offset:data >>>>> [ 2.625364] [0x00]:03100200 >>>>> [ 2.625597] [0x04]:00002300 >>>>> [ 2.625830] [0x08]:00000000 >>>>> [ 2.626064] [0x0c]:00000000 >>>>> [ 2.626296] [0x10]:00000000 >>>>> [ 2.626529] [0x14]:00010480 >>>>> [ 2.626769] [0x18]:22130d68 >>>>> [ 2.627002] [0x1c]:0001285c >>>>> [ 2.627235] [0x20]:14000400 >>>>> [ 2.627467] [0x24]:00000020 >>>>> [ 2.627702] [0x28]:0100000f >>>>> [ 2.627936] [0x2c]:000c000b >>>>> [ 2.628170] [0x30]:003c0003 >>>>> [ 2.628403] [0x34]:0020ffe0 >>>>> [ 2.628638] [0x38]:00800122 >>>>> [ 2.628872] [0x3c]:00000009 >>>>> [ 2.629107] mpt2sas_cm1: hba queue depth(3432), max chains per io(128) >>>>> [ 2.629388] mpt2sas_cm1: request frame size(128), reply frame size(128) >>>>> [ 2.629671] mpt2sas_cm1: _base_make_ioc_ready >>>>> [ 2.629928] mpt2sas_cm1: _base_get_port_facts >>>>> [ 2.660127] offset:data >>>>> [ 2.660389] [0x00]:05070000 >>>>> [ 2.660623] [0x04]:00000000 >>>>> [ 2.660858] [0x08]:00000000 >>>>> [ 2.661093] [0x0c]:00000000 >>>>> [ 2.661326] [0x10]:00000000 >>>>> [ 2.661562] [0x14]:00003000 >>>>> [ 2.661796] [0x18]:00000078 >>>>> [ 2.664346] mpt2sas_cm1: _base_allocate_memory_pools >>>>> [ 2.664608] mpt2sas_cm1: scatter gather: sge_in_main_msg(3), sge_per_chain(15), sge_per_io(128), chains_per_io(9) >>>>> [ 2.665142] mpt2sas_cm1: reply post free pool (0xffff8800b8b10000): depth(6944),element_size(8), pool_size(54 kB) >>>>> [ 2.666671] mpt2sas_cm1: reply_post_free_dma = (0xb8b10000) >>>>> [ 2.666954] mpt2sas_cm1: scsi host: can_queue depth (3307) >>>>> [ 2.667311] mpt2sas_cm1: request pool(0xffff8800b8b80000): depth(3432), frame_size(128), pool_size(429 kB) >>>>> [ 2.667813] mpt2sas_cm1: request pool: dma(0xb8b80000) >>>>> [ 2.668080] mpt2sas_cm1: scsiio(0xffff8800b8b80000): depth(3307) >>>>> [ 2.674131] mpt2sas_cm1: chain pool depth(29763), frame_size(128), pool_size(3720 kB) >>>>> [ 2.674448] mpt2sas_cm1: hi_priority(0xffff8800b8be7600): depth(60), start smid(3308) >>>>> [ 2.674750] mpt2sas_cm1: internal(0xffff8800b8be9400): depth(65), start smid(3368) >>>>> [ 2.675105] mpt2sas_cm1: sense pool(0xffff8800b8100000): depth(3307), element_size(96), pool_size(310 kB) >>>>> [ 2.675605] mpt2sas_cm1: sense_dma(0xb8100000) >>>>> [ 2.675944] mpt2sas_cm1: reply pool(0xffff8800b8180000): depth(3496), frame_size(128), pool_size(437 kB) >>>>> [ 2.676443] mpt2sas_cm1: reply_dma(0xb8180000) >>>>> [ 2.676702] mpt2sas_cm1: reply_free pool(0xffff8800b80a0000): depth(3496), element_size(4), pool_size(13 kB) >>>>> [ 2.677124] mpt2sas_cm1: reply_free_dma (0xb80a0000) >>>>> [ 2.677322] mpt2sas_cm1: config page(0xffff8800b807f000): size(512) >>>>> [ 2.677532] mpt2sas_cm1: config_page_dma(0xb807f000) >>>>> [ 2.677728] mpt2sas_cm1: Allocated physical memory: size(4964 kB) >>>>> [ 2.677936] mpt2sas_cm1: Current Controller Queue Depth(3307),Max Controller Queue Depth(3432) >>>>> [ 2.678304] mpt2sas_cm1: Scatter Gather Elements per IO(128) >>>>> [ 2.678514] mpt2sas_cm1: _base_make_ioc_operational >>>>> [ 2.679081] mpt2sas_cm1: _base_send_ioc_init >>>>> [ 2.679275] offset:data >>>>> [ 2.679448] [0x00]:02000004 >>>>> [ 2.679625] [0x04]:00000000 >>>>> [ 2.679805] [0x08]:00000000 >>>>> [ 2.681200] [0x0c]:23000200 >>>>> [ 2.681377] [0x10]:00000000 >>>>> [ 2.681554] [0x14]:00000000 >>>>> [ 2.681729] [0x18]:00200000 >>>>> [ 2.681906] [0x1c]:0da81b20 >>>>> [ 2.682082] [0x20]:00000000 >>>>> [ 2.682259] [0x24]:00000000 >>>>> [ 2.682435] [0x28]:b8b80000 >>>>> [ 2.682611] [0x2c]:00000000 >>>>> [ 2.682787] [0x30]:b8b10000 >>>>> [ 2.682963] [0x34]:00000000 >>>>> [ 2.683139] [0x38]:b80a0000 >>>>> [ 2.683314] [0x3c]:00000000 >>>>> [ 2.683489] [0x40]:98597011 >>>>> [ 2.683665] [0x44]:00000153 >>>>> [ 2.729849] offset:data >>>>> [ 2.730089] [0x00]:02050004 >>>>> [ 2.730349] [0x04]:00000000 >>>>> [ 2.730586] [0x08]:00000000 >>>>> [ 2.730822] [0x0c]:00000000 >>>>> [ 2.731058] [0x10]:00000000 >>>>> [ 2.731295] mpt2sas_cm1: _base_event_notification >>>>> [ 2.731606] mpt2sas_cm1: _base_event_notification: complete >>>>> [ 2.732501] mpt2sas_cm1: LSISAS2008: FWVersion(20.00.04.00), ChipRevision(0x02), BiosVersion(07.39.00.00) >>>>> [ 2.733010] mpt2sas_cm1: Protocol=( >>>>> [ 2.733074] Initiator >>>>> [ 2.733339] ,Target >>>>> [ 2.733384] ), >>>>> [ 2.733642] Capabilities=( >>>>> [ 2.733696] TLR >>>>> [ 2.733952] ,EEDP >>>>> [ 2.733995] ,Snapshot Buffer >>>>> [ 2.734268] ,Diag Trace Buffer >>>>> [ 2.734326] ,Task Set Full >>>>> [ 2.734595] ,NCQ >>>>> [ 2.734637] ) >>>>> [ 2.735155] scsi host1: Fusion MPT SAS Host >>>>> [ 2.749047] mpt2sas_cm1: sending port enable !! >>>>> [ 2.749563] mpt2sas_cm1: Discovery: (start) >>>>> >>>>> [ 2.749989] mpt2sas_cm1: SAS Enclosure Device Status Change >>>>> [ 2.750001] mpt2sas_cm1: discovery event: (start) >>>>> >>>>> [ 2.750578] mpt2sas_cm1: SAS Topology Change List >>>>> [ 2.750788] mpt2sas_cm1: Discovery: (stop) >>>>> >>>>> [ 2.751181] mpt2sas_cm1: Discovery: (start) >>>>> >>>>> [ 2.751571] mpt2sas_cm1: Discovery: (stop) >>>>> >>>>> [ 2.752002] mpt2sas_cm1: Discovery: (start) >>>>> >>>>> [ 2.752391] mpt2sas_cm1: Discovery: (stop) >>>>> >>>>> [ 2.752779] mpt2sas_cm1: Discovery: (start) >>>>> >>>>> [ 2.754205] mpt2sas_cm1: Discovery: (stop) >>>>> >>>>> [ 2.754593] mpt2sas_cm1: Discovery: (start) >>>>> >>>>> [ 2.754983] mpt2sas_cm1: Discovery: (stop) >>>>> >>>>> [ 2.755371] mpt2sas_cm1: Discovery: (start) >>>>> >>>>> [ 2.755762] mpt2sas_cm1: Discovery: (stop) >>>>> >>>>> [ 2.759602] mpt2sas_cm1: host_add: handle(0x0001), sas_addr(0x500605b0026f79b0), phys(8) >>>>> [ 2.759969] mpt2sas_cm1: enclosure status change: (enclosure add) >>>>> handle(0x0001), enclosure logical id(0x500605b0026f79b0) number slots(0) >>>>> [ 2.760407] mpt2sas_cm1: sas topology change: (responding) >>>>> [ 2.760612] handle(0x0000), enclosure_handle(0x0001) start_phy(00), count(8) >>>>> [ 2.760834] phy(02), attached_handle(0x000e): target add: link rate: new(0x0a), old(0x00) >>>>> [ 2.761066] phy(03), attached_handle(0x000b): target add: link rate: new(0x0a), old(0x00) >>>>> [ 2.761304] phy(04), attached_handle(0x000d): target add: link rate: new(0x09), old(0x00) >>>>> [ 2.761538] phy(05), attached_handle(0x0009): target add: link rate: new(0x09), old(0x00) >>>>> [ 2.761771] phy(06), attached_handle(0x000a): target add: link rate: new(0x09), old(0x00) >>>>> [ 2.762002] phy(07), attached_handle(0x000c): target add: link rate: new(0x09), old(0x00) >>>>> [ 2.762235] mpt2sas_cm1: updating handles for sas_host(0x500605b0026f79b0) >>>>> [ 2.763653] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x000e), sas_addr(0x4433221102000000) >>>>> [ 2.764036] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 1) >>>>> [ 2.764772] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x000b), sas_addr(0x4433221103000000) >>>>> [ 2.765147] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 0) >>>>> [ 2.765891] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x000d), sas_addr(0x4433221104000000) >>>>> [ 2.767250] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 7) >>>>> [ 2.768009] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x0009), sas_addr(0x4433221105000000) >>>>> [ 2.768394] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 6) >>>>> [ 2.769136] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x000a), sas_addr(0x4433221106000000) >>>>> [ 2.769510] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 5) >>>>> [ 2.769888] mpt2sas_cm1: _scsih_determine_boot_device: current_boot_device(0x4433221106000000) >>>>> [ 2.770641] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x000c), sas_addr(0x4433221107000000) >>>>> [ 2.771025] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 4) >>>>> [ 2.771405] mpt2sas_cm1: discovery event: (stop) >>>>> >>>>> [ 2.771788] mpt2sas_cm1: discovery event: (start) >>>>> >>>>> [ 2.772172] mpt2sas_cm1: discovery event: (stop) >>>>> >>>>> [ 2.772554] mpt2sas_cm1: discovery event: (start) >>>>> >>>>> [ 2.772942] mpt2sas_cm1: discovery event: (stop) >>>>> >>>>> [ 2.773326] mpt2sas_cm1: discovery event: (start) >>>>> >>>>> [ 2.773709] mpt2sas_cm1: discovery event: (stop) >>>>> >>>>> [ 2.774090] mpt2sas_cm1: discovery event: (start) >>>>> >>>>> [ 2.774474] mpt2sas_cm1: discovery event: (stop) >>>>> >>>>> [ 2.774855] mpt2sas_cm1: discovery event: (start) >>>>> >>>>> [ 2.775237] mpt2sas_cm1: discovery event: (stop) >>>>> >>>>> [ 2.775619] mpt2sas_cm1: port enable: complete from worker thread >>>>> [ 2.780192] mpt2sas_cm1: port enable: SUCCESS >>>>> [ 2.782404] scsi 1:0:0:0: Direct-Access ATA Hitachi HDP72505 A5BA PQ: 0 ANSI: 6 >>>>> [ 2.782651] scsi 1:0:0:0: SATA: handle(0x000a), sas_addr(0x4433221106000000), phy(6), device_name(0x5000cca34dc05584) >>>>> [ 2.783039] scsi 1:0:0:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(5) >>>>> [ 2.783390] scsi 1:0:0:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>> [ 2.803032] scsi 1:0:1:0: Direct-Access ATA ST8000AS0002-1NA AR15 PQ: 0 ANSI: 6 >>>>> [ 2.803272] scsi 1:0:1:0: SATA: handle(0x000e), sas_addr(0x4433221102000000), phy(2), device_name(0x5000c500908f1d05) >>>>> [ 2.803660] scsi 1:0:1:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(1) >>>>> [ 2.803981] scsi 1:0:1:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>> [ 2.821712] scsi 1:0:2:0: Direct-Access ATA ST3000DM001-1CH1 CC43 PQ: 0 ANSI: 6 >>>>> [ 2.821963] scsi 1:0:2:0: SATA: handle(0x000b), sas_addr(0x4433221103000000), phy(3), device_name(0x5000c5004dfd2a8a) >>>>> [ 2.822352] scsi 1:0:2:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(0) >>>>> [ 2.822694] scsi 1:0:2:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>> [ 2.844233] scsi 1:0:3:0: Direct-Access ATA ST3500320NS SN16 PQ: 0 ANSI: 6 >>>>> [ 2.844483] scsi 1:0:3:0: SATA: handle(0x000d), sas_addr(0x4433221104000000), phy(4), device_name(0x5000c50009dca65b) >>>>> [ 2.844870] scsi 1:0:3:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(7) >>>>> [ 2.845216] scsi 1:0:3:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>> [ 2.868963] scsi 1:0:4:0: Direct-Access ATA SAMSUNG HD401LJ 0-15 PQ: 0 ANSI: 6 >>>>> [ 2.870994] scsi 1:0:4:0: SATA: handle(0x0009), sas_addr(0x4433221105000000), phy(5), device_name(0x695d550daf678093) >>>>> [ 2.871382] scsi 1:0:4:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(6) >>>>> [ 2.871728] scsi 1:0:4:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>> [ 2.894004] scsi 1:0:5:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 >>>>> [ 2.894257] scsi 1:0:5:0: SATA: handle(0x000c), sas_addr(0x4433221107000000), phy(7), device_name(0x5000c5000266bb02) >>>>> [ 2.894646] scsi 1:0:5:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(4) >>>>> [ 2.894972] scsi 1:0:5:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>> >>>> I don't see a clear pattern yet, but I suspect warm rebooting >=4.2 >>>> after having run 4.1.x leads to sucessful driver inits. But I also >>>> remember having had cold boots, with kernels >=4.2 that worked fine >>>> (obviously not all of the time). <=4.1.20 kernels on the other hand boot >>>> fine every single time. >>>> >>>> Interestingly the igb driver (ethernet) seems to be acting up at least >>>> with 4.5.0 on exactly the same boots when mpt2sas init fails. I don't >>>> know whether this could be connected or not (I just became aware of this >>>> coincidence). >>>> >>>> >>>> --- >>>> Matthias >>>> >>>> >>>> Am 21.03.2016 um 05:53 schrieb Sreekanth Reddy: >>>>> Hi Matthias, >>>>> >>>>> Can you please share us the driver logs with driver logging_level set >>>>> to 0x3f8. So that we can get more info from this log. >>>>> >>>>> Thanks, >>>>> Sreekanth >>>>> >>>>> On Mon, Mar 21, 2016 at 1:44 AM, Matthias Prager >>>>> <linux@matthiasprager.de> wrote: >>>>>> Hello, >>>>>> >>>>>> I don't know what's the correct procedure, whether I should file a bug or first report this issue on the kernel mailing-list. So please feel free to tell me to open a ticket in the bugtracker (bugzilla.kernel.org?). >>>>>> >>>>>> But first let me present the issue I encounter: >>>>>> >>>>>> Kernels >= 4.2 (4.2.1 was the first on I tried, but also 4.3, 4.4 and 4.5) fail to load the mpt2sas driver on most (but not all) boots. Kernels <= 4.1.x work fine every single time (4.1.19 was the latest I tried, also 3.18.29). >>>>>> >>>>>> Here is the dmesg output for a failed driver init with Kernel 4.5.0: >>>>>>> [ 2.068313] mpt3sas version 09.102.00.00 loaded >>>>>>> [ 2.069412] mpt2sas_cm0: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3074748 kB) >>>>>>> [ 2.125260] mpt2sas_cm0: MSI-X vectors supported: 1, no of cores: 4, max_msix_vectors: -1 >>>>>>> [ 2.125996] mpt2sas0-msix0: PCI-MSI-X enabled: IRQ 58 >>>>>>> [ 2.126199] mpt2sas_cm0: iomem(0x00000000fd4fc000), mapped(0xffffc900000d0000), size(16384) >>>>>>> [ 2.126430] mpt2sas_cm0: ioport(0x0000000000004000), size(256) >>>>>>> [ 2.216371] mpt2sas_cm0: Allocated physical memory: size(4964 kB) >>>>>>> [ 2.216600] mpt2sas_cm0: Current Controller Queue Depth(3307),Max Controller Queue Depth(3432) >>>>>>> [ 2.217004] mpt2sas_cm0: Scatter Gather Elements per IO(128) >>>>>>> [ 5.086959] floppy0: no floppy controllers found >>>>>>> [ 32.256720] mpt2sas_cm0: _base_event_notification: timeout >>>>>>> [ 32.256940] mf: >>>>>>> >>>>>>> [ 32.257106] 07000000 >>>>>>> [ 32.257302] 00000000 >>>>>>> [ 32.257337] 00000000 >>>>>>> [ 32.257533] 00000000 >>>>>>> [ 32.257568] 00000000 >>>>>>> [ 32.257764] 0f2f7fff >>>>>>> [ 32.257800] ffffff7c >>>>>>> [ 32.257995] ffffffff >>>>>>> [ 32.258031] >>>>>>> >>>>>>> [ 32.258352] ffffffff >>>>>>> [ 32.258387] 00000000 >>>>>>> [ 32.258582] 00000000 >>>>>>> >>>>>>> [ 32.258950] mpt2sas_cm0: sending message unit reset !! >>>>>>> [ 32.260688] mpt2sas_cm0: message unit reset: SUCCESS >>>>>>> [ 32.325956] mpt2sas_cm0: failure at drivers/scsi/mpt3sas/mpt3sas_scsih.c:8592/_scsih_probe()! >>>>>> >>>>>> For comparison here is a dmesg output for a successful boot on Kernel 4.1.15: >>>>>>> [ 2.035568] mpt2sas version 20.100.00.00 loaded >>>>>>> [ 2.037243] mpt2sas0: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (2046352 kB) >>>>>>> [ 2.755374] mpt2sas0: MSI-X vectors supported: 1, no of cores: 3, max_msix_vectors: 8 >>>>>>> [ 2.756377] mpt2sas0-msix0: PCI-MSI-X enabled: IRQ 58 >>>>>>> [ 2.756708] mpt2sas0: iomem(0x00000000fd5fc000), mapped(0xffffc900000d0000), size(16384) >>>>>>> [ 2.757083] mpt2sas0: ioport(0x0000000000004000), size(256) >>>>>>> [ 3.842944] mpt2sas0: Allocated physical memory: size(4964 kB) >>>>>>> [ 3.843303] mpt2sas0: Current Controller Queue Depth(3307), Max Controller Queue Depth(3432) >>>>>>> [ 3.843717] mpt2sas0: Scatter Gather Elements per IO(128) >>>>>>> [ 4.415980] mpt2sas0: LSISAS2008: FWVersion(20.00.04.00), ChipRevision(0x03), BiosVersion(07.39.00.00) >>>>>>> [ 4.416618] mpt2sas0: Protocol=(Initiator,Target), Capabilities=(TLR,EEDP,Snapshot Buffer,Diag Trace Buffer,Task Set Full,NCQ) >>>>>>> [ 4.417846] scsi host0: Fusion MPT SAS Host >>>>>>> [ 4.436865] mpt2sas0: sending port enable !! >>>>>>> [ 4.440460] mpt2sas0: host_add: handle(0x0001), sas_addr(0xxxxxxxxxxxxxxxxx), phys(8) >>>>>>> >>>>>>> ... >>>>>>> [ 4.444045] scsi 0:0:0:0: Direct-Access ATA Hitachi HDS5C302 A800 PQ: 0 ANSI: 6 >>>>>>> [ 4.444338] scsi 0:0:0:0: SATA: handle(0x0009), sas_addr(0xxxxxxxxxxxxxxxxx), phy(1), device_name(0xxxxxxxxxxxxxxxxx) >>>>>>> [ 4.444823] scsi 0:0:0:0: SATA: enclosure_logical_id(0xxxxxxxxxxxxxxxxx), slot(2) >>>>>>> [ 4.445197] scsi 0:0:0:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>>>> ... (n times for n drives) >>>>>>> >>>>>>> [ 4.515443] mpt2sas0: port enable: SUCCESS >>>>>> >>>>>> >>>>>> The Controller(s) are all Avego/LSI 9211-8i running the latest version of IT firmware (v20.00.04.00). These are passed through to a gentoo-linux VM on an ESXi 5.1 host (latest patchlevel). I have two of these systems (one production one testing) with nearly identical hardware (Supermicro X8DTi-F boards with 2x Intel Westmere CPUs). I also have an older set of systems running the same software config (Intel S3200SHLC boards with single Core2Quad) which exhibit the same buggy behavior. >>>>>> >>>>>> The 'uname -a' line on the current testing system looks like this: >>>>>>> Linux pserver2 4.1.19-gentoo #4 SMP Thu Mar 17 16:02:48 CET 2016 x86_64 Intel(R) Xeon(R) CPU E5506 @ 2.13GHz GenuineIntel GNU/Linux >>>>>> p >>>>>> >>>>>> There seem to be other people with similar issues: >>>>>> <https://bbs.archlinux.org/viewtopic.php?id=209495> >>>>>> >>>>>> Any thoughts? >>>>>> >>>>>> --- >>>>>> Matthias >>>> > ^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [BUG] mpt2sas: driver init fails on kernel >=4.2 for 9211-8i IT 2016-03-22 10:52 ` Sreekanth Reddy @ 2016-03-22 21:02 ` Matthias Prager 2016-03-24 2:06 ` Matthias Prager 0 siblings, 1 reply; 13+ messages in thread From: Matthias Prager @ 2016-03-22 21:02 UTC (permalink / raw) To: Sreekanth Reddy; +Cc: linux-scsi, Matthias Prager Hi Sreekanth, Am 22.03.2016 um 11:52 schrieb Sreekanth Reddy: > Hi Matthias, > > Thanks for providing detail explanation. > > Currently I am trying to reproduce this issue locally. I have used the > same HBA card but still I am not able to reproduce this issue on 4.5 > kernel. > > I will try for few more times and I will also try to get the diff > between 4.1 to 4.5 kernels w.r.t msix vectors support. I will try to bisect this tomorrow. And I will try to reproduce this outside the VM environment on bare metal. > > Meanwhile can you please provide me the output of "lspci -vvv" command > for LSI SAS2 HBA's and also hexdump of config sysfs parameter for SAS2 > pci device. I need this data to be collected before "timeout" print is > observed, or in the mpt3sas_base.c file and in the > mpt3sas_base_attach(). return from mpt3sas_base_attach() function if > return value of mpt3sas_base_map_resources() is non zero instead of > freeing the resources, as shown below > > --------------------------------------------------------------------------- > r = mpt3sas_base_map_resources(ioc); > if (r) > - goto out_free_resources; > + return r; > ----------------------------------------------------------------------------- I will get you this data tomorrow too. > > Also are you sure that this issue won't occur on less than 4.1 kernel? Yes definitely - I never observed these timeouts with any kernel <=4.1.20, and I started seeing them from kernel 4.2.1 onward (I haven't actually tested 4.2.0 yet). > > Thanks, > Sreekanth > > On Mon, Mar 21, 2016 at 10:00 PM, Matthias Prager > <linux@matthiasprager.de> wrote: >> Am 21.03.2016 um 16:52 schrieb Matthias Prager: >>> Hi Sreekanth, >>> >>> thanks for digging into this issue. Regarding the 4.5.0 after 4.1.20 >>> boot statement, I will try to express myself better: >>> >>> I first started the system with the 4.1.20 kernel. Then I issued an >>> 'init 6' warm-reboot and chose to boot the 4.5.0 kernel. This procedure >>> often works (i.e. I'm able to boot the newer kernels (>=4.2) this way >>> with mpt2sas initializing just fine). >> One small addition: warm-rebooting kernel 4.5.0 from kernel 4.5.0 >> reliably leads to this issue manifesting (mpt2sas driver not initializing). >> >>> >>> I will try the msix_disable parameter and report back. Maybe kernel >>> version 4.2 broke interrupt handling somehow? >> With the msix_disable parameter set kernels 4.5.0, 4.4.5, 4.3.3 and >> 4.2.1 boot without the mpt2sas init issue. I also tried the pci=nomsi >> paremeter instead, which also works fine. >> >> The igb ethernet-driver issue I mentioned as possibly related has not >> changed with pci=nomsi. So I'm assuming it is not the same issue, but >> possibly related, since it also occurs on kernels >=4.2. >> >>> >>> --- >>> Matthias >>> >>> >>> Am 21.03.2016 um 14:59 schrieb Sreekanth Reddy: >>>> Hi Matthias, >>>> >>>> Thanks for providing the logs. In these logs, I am not observing any >>>> such a prints which should be suspected for this issue. >>>> >>>> Can you please try once by setting mpt3sas driver's "msix_disable" >>>> module parameter to one. >>>> >>>> Also, can you please elaborate below statement for me, I am not able >>>> understand this statement >>>> "I managed to boot the same 4.5.0 kernel successfully after warm >>>> rebooting from 4.1.20" >>>> >>>> Thanks, >>>> Sreekanth >>>> >>>> On Mon, Mar 21, 2016 at 2:48 PM, Matthias Prager >>>> <linux@matthiasprager.de> wrote: >>>>> Hi Sreekanth, >>>>> >>>>> thank you for replying so quickly. Here are the logs you requested >>>>> (kernel 4.5.0): >>>>> >>>>>> [ 2.083177] mpt3sas version 09.102.00.00 loaded >>>>>> [ 2.083757] mpt2sas_cm0: mpt3sas_base_attach >>>>>> [ 2.083956] mpt2sas_cm0: mpt3sas_base_map_resources >>>>>> [ 2.084708] mpt2sas_cm0: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3074748 kB) >>>>>> [ 2.084964] mpt2sas_cm0: _base_get_ioc_facts >>>>>> [ 2.085154] mpt2sas_cm0: _base_wait_for_iocstate >>>>>> [ 2.140893] offset:data >>>>>> [ 2.141082] [0x00]:03100200 >>>>>> [ 2.141257] [0x04]:00002300 >>>>>> [ 2.141432] [0x08]:00000000 >>>>>> [ 2.141606] [0x0c]:00000000 >>>>>> [ 2.141780] [0x10]:00000000 >>>>>> [ 2.141955] [0x14]:00010480 >>>>>> [ 2.142129] [0x18]:22130d68 >>>>>> [ 2.142303] [0x1c]:0001285c >>>>>> [ 2.142477] [0x20]:14000400 >>>>>> [ 2.142651] [0x24]:00000020 >>>>>> [ 2.142825] [0x28]:0100000f >>>>>> [ 2.143000] [0x2c]:000c000b >>>>>> [ 2.143174] [0x30]:003c0003 >>>>>> [ 2.143349] [0x34]:0020ffe0 >>>>>> [ 2.143544] [0x38]:00800122 >>>>>> [ 2.143719] [0x3c]:00000009 >>>>>> [ 2.143895] mpt2sas_cm0: hba queue depth(3432), max chains per io(128) >>>>>> [ 2.144106] mpt2sas_cm0: request frame size(128), reply frame size(128) >>>>>> [ 2.144397] mpt2sas_cm0: msix is supported, vector_count(1) >>>>>> [ 2.144600] mpt2sas_cm0: MSI-X vectors supported: 1, no of cores: 4, max_msix_vectors: -1 >>>>>> [ 2.145161] mpt2sas0-msix0: PCI-MSI-X enabled: IRQ 58 >>>>>> [ 2.145361] mpt2sas_cm0: iomem(0x00000000fd4fc000), mapped(0xffffc900000d0000), size(16384) >>>>>> [ 2.145591] mpt2sas_cm0: ioport(0x0000000000004000), size(256) >>>>>> [ 2.146206] mpt2sas_cm0: _base_get_ioc_facts >>>>>> [ 2.146397] mpt2sas_cm0: _base_wait_for_iocstate >>>>>> [ 2.202087] offset:data >>>>>> [ 2.202281] [0x00]:03100200 >>>>>> [ 2.202456] [0x04]:00002300 >>>>>> [ 2.202631] [0x08]:00000000 >>>>>> [ 2.202805] [0x0c]:00000000 >>>>>> [ 2.202980] [0x10]:00000000 >>>>>> [ 2.203154] [0x14]:00010480 >>>>>> [ 2.203328] [0x18]:22130d68 >>>>>> [ 2.203521] [0x1c]:0001285c >>>>>> [ 2.203695] [0x20]:14000400 >>>>>> [ 2.203870] [0x24]:00000020 >>>>>> [ 2.204044] [0x28]:0100000f >>>>>> [ 2.204219] [0x2c]:000c000b >>>>>> [ 2.204394] [0x30]:003c0003 >>>>>> [ 2.204571] [0x34]:0020ffe0 >>>>>> [ 2.204746] [0x38]:00800122 >>>>>> [ 2.204926] [0x3c]:00000009 >>>>>> [ 2.205102] mpt2sas_cm0: hba queue depth(3432), max chains per io(128) >>>>>> [ 2.205314] mpt2sas_cm0: request frame size(128), reply frame size(128) >>>>>> [ 2.205528] mpt2sas_cm0: _base_make_ioc_ready >>>>>> [ 2.205719] mpt2sas_cm0: _base_get_port_facts >>>>>> [ 2.234205] offset:data >>>>>> [ 2.234397] [0x00]:05070000 >>>>>> [ 2.234573] [0x04]:00000000 >>>>>> [ 2.234748] [0x08]:00000000 >>>>>> [ 2.234928] [0x0c]:00000000 >>>>>> [ 2.235103] [0x10]:00000000 >>>>>> [ 2.235278] [0x14]:00003000 >>>>>> [ 2.235453] [0x18]:00000078 >>>>>> [ 2.235629] mpt2sas_cm0: _base_allocate_memory_pools >>>>>> [ 2.235826] mpt2sas_cm0: scatter gather: sge_in_main_msg(3), sge_per_chain(15), sge_per_io(128), chains_per_io(9) >>>>>> [ 2.236227] mpt2sas_cm0: reply post free pool (0xffff8800bb380000): depth(6944),element_size(8), pool_size(54 kB) >>>>>> [ 2.236611] mpt2sas_cm0: reply_post_free_dma = (0xbb380000) >>>>>> [ 2.236813] mpt2sas_cm0: scsi host: can_queue depth (3307) >>>>>> [ 2.237086] mpt2sas_cm0: request pool(0xffff8800ba880000): depth(3432), frame_size(128), pool_size(429 kB) >>>>>> [ 2.238580] mpt2sas_cm0: request pool: dma(0xba880000) >>>>>> [ 2.238781] mpt2sas_cm0: scsiio(0xffff8800ba880000): depth(3307) >>>>>> [ 2.243644] mpt2sas_cm0: chain pool depth(29763), frame_size(128), pool_size(3720 kB) >>>>>> [ 2.243887] mpt2sas_cm0: hi_priority(0xffff8800ba8e7600): depth(60), start smid(3308) >>>>>> [ 2.244113] mpt2sas_cm0: internal(0xffff8800ba8e9400): depth(65), start smid(3368) >>>>>> [ 2.244390] mpt2sas_cm0: sense pool(0xffff8800ba480000): depth(3307), element_size(96), pool_size(310 kB) >>>>>> [ 2.244774] mpt2sas_cm0: sense_dma(0xba480000) >>>>>> [ 2.245038] mpt2sas_cm0: reply pool(0xffff8800ba500000): depth(3496), frame_size(128), pool_size(437 kB) >>>>>> [ 2.245413] mpt2sas_cm0: reply_dma(0xba500000) >>>>>> [ 2.245608] mpt2sas_cm0: reply_free pool(0xffff8800ba430000): depth(3496), element_size(4), pool_size(13 kB) >>>>>> [ 2.245985] mpt2sas_cm0: reply_free_dma (0xba430000) >>>>>> [ 2.246181] mpt2sas_cm0: config page(0xffff8800ba429000): size(512) >>>>>> [ 2.246389] mpt2sas_cm0: config_page_dma(0xba429000) >>>>>> [ 2.246584] mpt2sas_cm0: Allocated physical memory: size(4964 kB) >>>>>> [ 2.246791] mpt2sas_cm0: Current Controller Queue Depth(3307),Max Controller Queue Depth(3432) >>>>>> [ 2.247155] mpt2sas_cm0: Scatter Gather Elements per IO(128) >>>>>> [ 2.247361] mpt2sas_cm0: _base_make_ioc_operational >>>>>> [ 2.247962] mpt2sas_cm0: _base_send_ioc_init >>>>>> [ 2.248154] offset:data >>>>>> [ 2.248325] [0x00]:02000004 >>>>>> [ 2.248499] [0x04]:00000000 >>>>>> [ 2.248673] [0x08]:00000000 >>>>>> [ 2.248848] [0x0c]:23000200 >>>>>> [ 2.249023] [0x10]:00000000 >>>>>> [ 2.249197] [0x14]:00000000 >>>>>> [ 2.249372] [0x18]:00200000 >>>>>> [ 2.249546] [0x1c]:0da81b20 >>>>>> [ 2.249720] [0x20]:00000000 >>>>>> [ 2.249894] [0x24]:00000000 >>>>>> [ 2.250068] [0x28]:ba880000 >>>>>> [ 2.250242] [0x2c]:00000000 >>>>>> [ 2.250416] [0x30]:bb380000 >>>>>> [ 2.250589] [0x34]:00000000 >>>>>> [ 2.250768] [0x38]:ba430000 >>>>>> [ 2.250941] [0x3c]:00000000 >>>>>> [ 2.251115] [0x40]:983eb686 >>>>>> [ 2.251288] [0x44]:00000153 >>>>>> [ 2.296610] offset:data >>>>>> [ 2.296795] [0x00]:02050004 >>>>>> [ 2.296969] [0x04]:00000000 >>>>>> [ 2.297143] [0x08]:00000000 >>>>>> [ 2.297318] [0x0c]:00000000 >>>>>> [ 2.297493] [0x10]:00000000 >>>>>> [ 2.297668] mpt2sas_cm0: _base_event_notification >>>>>> [ 5.093707] floppy0: no floppy controllers found >>>>>> [ 32.293619] mpt2sas_cm0: _base_event_notification: timeout >>>>>> [ 32.293909] mf: >>>>>> >>>>>> [ 32.294132] 07000000 >>>>>> [ 32.294397] 00000000 >>>>>> [ 32.294445] 00000000 >>>>>> [ 32.294719] 00000000 >>>>>> [ 32.294767] 00000000 >>>>>> [ 32.295031] 0f2f7fff >>>>>> [ 32.295078] ffffff7c >>>>>> [ 32.295342] ffffffff >>>>>> [ 32.295389] >>>>>> >>>>>> [ 32.295823] ffffffff >>>>>> [ 32.295871] 00000000 >>>>>> [ 32.296134] 00000000 >>>>>> >>>>>> [ 32.296615] mpt2sas_cm0: mpt3sas_base_free_resources >>>>>> [ 32.296880] mpt2sas_cm0: _base_make_ioc_ready >>>>>> [ 32.297135] mpt2sas_cm0: sending message unit reset !! >>>>>> [ 32.298941] mpt2sas_cm0: message unit reset: SUCCESS >>>>>> [ 32.299212] mpt2sas_cm0: mpt3sas_base_unmap_resources >>>>>> [ 32.300381] mpt2sas_cm0: _base_release_memory_pools >>>>>> [ 32.300654] mpt2sas_cm0: request_pool(0xffff8800ba880000): free >>>>>> [ 32.300934] mpt2sas_cm0: sense_pool(0xffff8800ba480000): free >>>>>> [ 32.301211] mpt2sas_cm0: reply_pool(0xffff8800ba500000): free >>>>>> [ 32.301485] mpt2sas_cm0: reply_free_pool(0xffff8800ba430000): free >>>>>> [ 32.301774] mpt2sas_cm0: reply_post_free_pool(0xffff8800bb380000): free >>>>>> [ 32.302061] mpt2sas_cm0: config_page(0xffff8800ba429000): free >>>>>> [ 32.371097] mpt2sas_cm0: failure at drivers/scsi/mpt3sas/mpt3sas_scsih.c:8592/_scsih_probe()! >>>>>> [ 32.371958] mpt2sas_cm1: mpt3sas_base_attach >>>>>> [ 32.372154] mpt2sas_cm1: mpt3sas_base_map_resources >>>>>> [ 32.372950] mpt2sas_cm1: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3074748 kB) >>>>>> [ 32.373201] mpt2sas_cm1: _base_get_ioc_facts >>>>>> [ 32.375261] mpt2sas_cm1: _base_wait_for_iocstate >>>>>> [ 32.432012] offset:data >>>>>> [ 32.432262] [0x00]:03100200 >>>>>> [ 32.432499] [0x04]:00002300 >>>>>> [ 32.432735] [0x08]:00000000 >>>>>> [ 32.432971] [0x0c]:00000000 >>>>>> [ 32.433206] [0x10]:00000000 >>>>>> [ 32.433443] [0x14]:00010480 >>>>>> [ 32.433701] [0x18]:22130d68 >>>>>> [ 32.433937] [0x1c]:0001285c >>>>>> [ 32.435434] [0x20]:14000400 >>>>>> [ 32.435674] [0x24]:00000020 >>>>>> [ 32.435909] [0x28]:0100000f >>>>>> [ 32.436144] [0x2c]:000c000b >>>>>> [ 32.436379] [0x30]:003c0003 >>>>>> [ 32.436615] [0x34]:0020ffe0 >>>>>> [ 32.436850] [0x38]:00800122 >>>>>> [ 32.437085] [0x3c]:00000009 >>>>>> [ 32.437322] mpt2sas_cm1: hba queue depth(3432), max chains per io(128) >>>>>> [ 32.437607] mpt2sas_cm1: request frame size(128), reply frame size(128) >>>>>> [ 32.438014] mpt2sas_cm1: msix is supported, vector_count(1) >>>>>> [ 32.438288] mpt2sas_cm1: MSI-X vectors supported: 1, no of cores: 4, max_msix_vectors: 8 >>>>>> [ 32.439101] mpt2sas1-msix0: PCI-MSI-X enabled: IRQ 58 >>>>>> [ 32.439373] mpt2sas_cm1: iomem(0x00000000fd1fc000), mapped(0xffffc900000d8000), size(16384) >>>>>> [ 32.439682] mpt2sas_cm1: ioport(0x0000000000007000), size(256) >>>>>> [ 32.440504] mpt2sas_cm1: _base_get_ioc_facts >>>>>> [ 32.440765] mpt2sas_cm1: _base_wait_for_iocstate >>>>>> [ 32.499305] offset:data >>>>>> [ 32.499557] [0x00]:03100200 >>>>>> [ 32.499794] [0x04]:00002300 >>>>>> [ 32.500031] [0x08]:00000000 >>>>>> [ 32.500267] [0x0c]:00000000 >>>>>> [ 32.500504] [0x10]:00000000 >>>>>> [ 32.500740] [0x14]:00010480 >>>>>> [ 32.500974] [0x18]:22130d68 >>>>>> [ 32.501209] [0x1c]:0001285c >>>>>> [ 32.501444] [0x20]:14000400 >>>>>> [ 32.501687] [0x24]:00000020 >>>>>> [ 32.501922] [0x28]:0100000f >>>>>> [ 32.502157] [0x2c]:000c000b >>>>>> [ 32.502391] [0x30]:003c0003 >>>>>> [ 32.502626] [0x34]:0020ffe0 >>>>>> [ 32.502862] [0x38]:00800122 >>>>>> [ 32.503098] [0x3c]:00000009 >>>>>> [ 32.503336] mpt2sas_cm1: hba queue depth(3432), max chains per io(128) >>>>>> [ 32.503644] mpt2sas_cm1: request frame size(128), reply frame size(128) >>>>>> [ 32.503933] mpt2sas_cm1: _base_make_ioc_ready >>>>>> [ 32.504191] mpt2sas_cm1: _base_get_port_facts >>>>>> [ 32.534282] offset:data >>>>>> [ 32.534537] [0x00]:05070000 >>>>>> [ 32.534782] [0x04]:00000000 >>>>>> [ 32.535058] [0x08]:00000000 >>>>>> [ 32.536473] [0x0c]:00000000 >>>>>> [ 32.536710] [0x10]:00000000 >>>>>> [ 32.536946] [0x14]:00003000 >>>>>> [ 32.537183] [0x18]:00000078 >>>>>> [ 32.537420] mpt2sas_cm1: _base_allocate_memory_pools >>>>>> [ 32.537686] mpt2sas_cm1: scatter gather: sge_in_main_msg(3), sge_per_chain(15), sge_per_io(128), chains_per_io(9) >>>>>> [ 32.538232] mpt2sas_cm1: reply post free pool (0xffff8800bb3d0000): depth(6944),element_size(8), pool_size(54 kB) >>>>>> [ 32.538758] mpt2sas_cm1: reply_post_free_dma = (0xbb3d0000) >>>>>> [ 32.539030] mpt2sas_cm1: scsi host: can_queue depth (3307) >>>>>> [ 32.539378] mpt2sas_cm1: request pool(0xffff8800ba480000): depth(3432), frame_size(128), pool_size(429 kB) >>>>>> [ 32.539882] mpt2sas_cm1: request pool: dma(0xba480000) >>>>>> [ 32.540149] mpt2sas_cm1: scsiio(0xffff8800ba480000): depth(3307) >>>>>> [ 32.545893] mpt2sas_cm1: chain pool depth(29763), frame_size(128), pool_size(3720 kB) >>>>>> [ 32.546137] mpt2sas_cm1: hi_priority(0xffff8800ba4e7600): depth(60), start smid(3308) >>>>>> [ 32.546365] mpt2sas_cm1: internal(0xffff8800ba4e9400): depth(65), start smid(3368) >>>>>> [ 32.546651] mpt2sas_cm1: sense pool(0xffff8800ba880000): depth(3307), element_size(96), pool_size(310 kB) >>>>>> [ 32.547030] mpt2sas_cm1: sense_dma(0xba880000) >>>>>> [ 32.547537] mpt2sas_cm1: reply pool(0xffff880000100000): depth(3496), frame_size(128), pool_size(437 kB) >>>>>> [ 32.547921] mpt2sas_cm1: reply_dma(0x100000) >>>>>> [ 32.548117] mpt2sas_cm1: reply_free pool(0xffff8800ba964000): depth(3496), element_size(4), pool_size(13 kB) >>>>>> [ 32.548500] mpt2sas_cm1: reply_free_dma (0xba964000) >>>>>> [ 32.548698] mpt2sas_cm1: config page(0xffff8800ba960000): size(512) >>>>>> [ 32.548908] mpt2sas_cm1: config_page_dma(0xba960000) >>>>>> [ 32.549105] mpt2sas_cm1: Allocated physical memory: size(4964 kB) >>>>>> [ 32.549314] mpt2sas_cm1: Current Controller Queue Depth(3307),Max Controller Queue Depth(3432) >>>>>> [ 32.550950] mpt2sas_cm1: Scatter Gather Elements per IO(128) >>>>>> [ 32.551160] mpt2sas_cm1: _base_make_ioc_operational >>>>>> [ 32.551855] mpt2sas_cm1: _base_send_ioc_init >>>>>> [ 32.552051] offset:data >>>>>> [ 32.552224] [0x00]:02000004 >>>>>> [ 32.552400] [0x04]:00000000 >>>>>> [ 32.552576] [0x08]:00000000 >>>>>> [ 32.552761] [0x0c]:23000200 >>>>>> [ 32.552937] [0x10]:00000000 >>>>>> [ 32.553114] [0x14]:00000000 >>>>>> [ 32.553291] [0x18]:00200000 >>>>>> [ 32.553468] [0x1c]:0da81b20 >>>>>> [ 32.553685] [0x20]:00000000 >>>>>> [ 32.553862] [0x24]:00000000 >>>>>> [ 32.554038] [0x28]:ba480000 >>>>>> [ 32.554215] [0x2c]:00000000 >>>>>> [ 32.554393] [0x30]:bb3d0000 >>>>>> [ 32.554569] [0x34]:00000000 >>>>>> [ 32.554752] [0x38]:ba964000 >>>>>> [ 32.554929] [0x3c]:00000000 >>>>>> [ 32.555106] [0x40]:983f2ce6 >>>>>> [ 32.555283] [0x44]:00000153 >>>>>> [ 32.601516] offset:data >>>>>> [ 32.601768] [0x00]:02050004 >>>>>> [ 32.602003] [0x04]:00000000 >>>>>> [ 32.602239] [0x08]:00000000 >>>>>> [ 32.602474] [0x0c]:00000000 >>>>>> [ 32.602709] [0x10]:00000000 >>>>>> [ 32.602945] mpt2sas_cm1: _base_event_notification >>>>>> [ 62.593604] mpt2sas_cm1: _base_event_notification: timeout >>>>>> [ 62.593906] mf: >>>>>> >>>>>> [ 62.594127] 07000000 >>>>>> [ 62.594390] 00000000 >>>>>> [ 62.594438] 00000000 >>>>>> [ 62.594709] 00000000 >>>>>> [ 62.594757] 00000000 >>>>>> [ 62.595019] 0f2f7fff >>>>>> [ 62.595067] ffffff7c >>>>>> [ 62.595330] ffffffff >>>>>> [ 62.595377] >>>>>> >>>>>> [ 62.595808] ffffffff >>>>>> [ 62.595855] 00000000 >>>>>> [ 62.596117] 00000000 >>>>>> >>>>>> [ 62.596601] mpt2sas_cm1: mpt3sas_base_free_resources >>>>>> [ 62.596871] mpt2sas_cm1: _base_make_ioc_ready >>>>>> [ 62.597125] mpt2sas_cm1: sending message unit reset !! >>>>>> [ 62.599013] mpt2sas_cm1: message unit reset: SUCCESS >>>>>> [ 62.599283] mpt2sas_cm1: mpt3sas_base_unmap_resources >>>>>> [ 62.600443] mpt2sas_cm1: _base_release_memory_pools >>>>>> [ 62.600721] mpt2sas_cm1: request_pool(0xffff8800ba480000): free >>>>>> [ 62.601002] mpt2sas_cm1: sense_pool(0xffff8800ba880000): free >>>>>> [ 62.601280] mpt2sas_cm1: reply_pool(0xffff880000100000): free >>>>>> [ 62.601560] mpt2sas_cm1: reply_free_pool(0xffff8800ba964000): free >>>>>> [ 62.601845] mpt2sas_cm1: reply_post_free_pool(0xffff8800bb3d0000): free >>>>>> [ 62.602133] mpt2sas_cm1: config_page(0xffff8800ba960000): free >>>>>> [ 62.673591] mpt2sas_cm1: failure at drivers/scsi/mpt3sas/mpt3sas_scsih.c:8592/_scsih_probe()! >>>>> >>>>> These are for two controllers, I don't know whether the output from the >>>>> second is helpful at all - I added it anyway. >>>>> >>>>> >>>>> I managed to boot the same 4.5.0 kernel successfully after warm >>>>> rebooting from 4.1.20. That gave me this dmesg output (for comparison): >>>>> >>>>>> [ 2.057685] mpt3sas version 09.102.00.00 loaded >>>>>> [ 2.058371] mpt2sas_cm0: mpt3sas_base_attach >>>>>> [ 2.058632] mpt2sas_cm0: mpt3sas_base_map_resources >>>>>> [ 2.059583] mpt2sas_cm0: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3074748 kB) >>>>>> [ 2.059911] mpt2sas_cm0: _base_get_ioc_facts >>>>>> [ 2.060166] mpt2sas_cm0: _base_wait_for_iocstate >>>>>> [ 2.116337] offset:data >>>>>> [ 2.116576] [0x00]:03100200 >>>>>> [ 2.116817] [0x04]:00002300 >>>>>> [ 2.117051] [0x08]:00000000 >>>>>> [ 2.117285] [0x0c]:00000000 >>>>>> [ 2.117518] [0x10]:00000000 >>>>>> [ 2.117752] [0x14]:00010480 >>>>>> [ 2.117986] [0x18]:22130d68 >>>>>> [ 2.118220] [0x1c]:0001285c >>>>>> [ 2.119624] [0x20]:14000400 >>>>>> [ 2.119858] [0x24]:00000020 >>>>>> [ 2.120093] [0x28]:0100000f >>>>>> [ 2.120351] [0x2c]:000c000b >>>>>> [ 2.120586] [0x30]:003c0003 >>>>>> [ 2.120820] [0x34]:0020ffe0 >>>>>> [ 2.121055] [0x38]:00800122 >>>>>> [ 2.121288] [0x3c]:00000009 >>>>>> [ 2.121524] mpt2sas_cm0: hba queue depth(3432), max chains per io(128) >>>>>> [ 2.121808] mpt2sas_cm0: request frame size(128), reply frame size(128) >>>>>> [ 2.122195] mpt2sas_cm0: msix is supported, vector_count(1) >>>>>> [ 2.122468] mpt2sas_cm0: MSI-X vectors supported: 1, no of cores: 4, max_msix_vectors: -1 >>>>>> [ 2.123239] mpt2sas0-msix0: PCI-MSI-X enabled: IRQ 58 >>>>>> [ 2.123507] mpt2sas_cm0: iomem(0x00000000fd4fc000), mapped(0xffffc900000d0000), size(16384) >>>>>> [ 2.123816] mpt2sas_cm0: ioport(0x0000000000004000), size(256) >>>>>> [ 2.124623] mpt2sas_cm0: _base_get_ioc_facts >>>>>> [ 2.124878] mpt2sas_cm0: _base_wait_for_iocstate >>>>>> [ 2.180907] offset:data >>>>>> [ 2.181145] [0x00]:03100200 >>>>>> [ 2.181379] [0x04]:00002300 >>>>>> [ 2.181613] [0x08]:00000000 >>>>>> [ 2.181847] [0x0c]:00000000 >>>>>> [ 2.182081] [0x10]:00000000 >>>>>> [ 2.182315] [0x14]:00010480 >>>>>> [ 2.182547] [0x18]:22130d68 >>>>>> [ 2.182781] [0x1c]:0001285c >>>>>> [ 2.183014] [0x20]:14000400 >>>>>> [ 2.183248] [0x24]:00000020 >>>>>> [ 2.183481] [0x28]:0100000f >>>>>> [ 2.183720] [0x2c]:000c000b >>>>>> [ 2.183954] [0x30]:003c0003 >>>>>> [ 2.184190] [0x34]:0020ffe0 >>>>>> [ 2.184424] [0x38]:00800122 >>>>>> [ 2.184658] [0x3c]:00000009 >>>>>> [ 2.184893] mpt2sas_cm0: hba queue depth(3432), max chains per io(128) >>>>>> [ 2.185177] mpt2sas_cm0: request frame size(128), reply frame size(128) >>>>>> [ 2.185462] mpt2sas_cm0: _base_make_ioc_ready >>>>>> [ 2.185717] mpt2sas_cm0: _base_get_port_facts >>>>>> [ 2.214057] offset:data >>>>>> [ 2.214295] [0x00]:05070000 >>>>>> [ 2.214529] [0x04]:00000000 >>>>>> [ 2.214762] [0x08]:00000000 >>>>>> [ 2.214997] [0x0c]:00000000 >>>>>> [ 2.215230] [0x10]:00000000 >>>>>> [ 2.215464] [0x14]:00003000 >>>>>> [ 2.215697] [0x18]:00000078 >>>>>> [ 2.215931] mpt2sas_cm0: _base_allocate_memory_pools >>>>>> [ 2.216194] mpt2sas_cm0: scatter gather: sge_in_main_msg(3), sge_per_chain(15), sge_per_io(128), chains_per_io(9) >>>>>> [ 2.216734] mpt2sas_cm0: reply post free pool (0xffff8800bafc0000): depth(6944),element_size(8), pool_size(54 kB) >>>>>> [ 2.217244] mpt2sas_cm0: reply_post_free_dma = (0xbafc0000) >>>>>> [ 2.217514] mpt2sas_cm0: scsi host: can_queue depth (3307) >>>>>> [ 2.217866] mpt2sas_cm0: request pool(0xffff8800ba800000): depth(3432), frame_size(128), pool_size(429 kB) >>>>>> [ 2.218369] mpt2sas_cm0: request pool: dma(0xba800000) >>>>>> [ 2.218637] mpt2sas_cm0: scsiio(0xffff8800ba800000): depth(3307) >>>>>> [ 2.224773] mpt2sas_cm0: chain pool depth(29763), frame_size(128), pool_size(3720 kB) >>>>>> [ 2.225092] mpt2sas_cm0: hi_priority(0xffff8800ba867600): depth(60), start smid(3308) >>>>>> [ 2.225395] mpt2sas_cm0: internal(0xffff8800ba869400): depth(65), start smid(3368) >>>>>> [ 2.225958] mpt2sas_cm0: sense pool(0xffff8800ba480000): depth(3307), element_size(96), pool_size(310 kB) >>>>>> [ 2.226457] mpt2sas_cm0: sense_dma(0xba480000) >>>>>> [ 2.227039] mpt2sas_cm0: reply pool(0xffff8800ba500000): depth(3496), frame_size(128), pool_size(437 kB) >>>>>> [ 2.227413] mpt2sas_cm0: reply_dma(0xba500000) >>>>>> [ 2.227616] mpt2sas_cm0: reply_free pool(0xffff8800ba450000): depth(3496), element_size(4), pool_size(13 kB) >>>>>> [ 2.227992] mpt2sas_cm0: reply_free_dma (0xba450000) >>>>>> [ 2.228192] mpt2sas_cm0: config page(0xffff8800ba43b000): size(512) >>>>>> [ 2.228402] mpt2sas_cm0: config_page_dma(0xba43b000) >>>>>> [ 2.228598] mpt2sas_cm0: Allocated physical memory: size(4964 kB) >>>>>> [ 2.228806] mpt2sas_cm0: Current Controller Queue Depth(3307),Max Controller Queue Depth(3432) >>>>>> [ 2.229171] mpt2sas_cm0: Scatter Gather Elements per IO(128) >>>>>> [ 2.229378] mpt2sas_cm0: _base_make_ioc_operational >>>>>> [ 2.229959] mpt2sas_cm0: _base_send_ioc_init >>>>>> [ 2.230151] offset:data >>>>>> [ 2.230323] [0x00]:02000004 >>>>>> [ 2.230499] [0x04]:00000000 >>>>>> [ 2.230675] [0x08]:00000000 >>>>>> [ 2.230851] [0x0c]:23000200 >>>>>> [ 2.231026] [0x10]:00000000 >>>>>> [ 2.231201] [0x14]:00000000 >>>>>> [ 2.231376] [0x18]:00200000 >>>>>> [ 2.231551] [0x1c]:0da81b20 >>>>>> [ 2.231726] [0x20]:00000000 >>>>>> [ 2.231900] [0x24]:00000000 >>>>>> [ 2.232075] [0x28]:ba800000 >>>>>> [ 2.232250] [0x2c]:00000000 >>>>>> [ 2.232423] [0x30]:bafc0000 >>>>>> [ 2.232597] [0x34]:00000000 >>>>>> [ 2.232775] [0x38]:ba450000 >>>>>> [ 2.232950] [0x3c]:00000000 >>>>>> [ 2.233125] [0x40]:98596e4f >>>>>> [ 2.233299] [0x44]:00000153 >>>>>> [ 2.278752] offset:data >>>>>> [ 2.278988] [0x00]:02050004 >>>>>> [ 2.279220] [0x04]:00000000 >>>>>> [ 2.279453] [0x08]:00000000 >>>>>> [ 2.279685] [0x0c]:00000000 >>>>>> [ 2.279918] [0x10]:00000000 >>>>>> [ 2.280151] mpt2sas_cm0: _base_event_notification >>>>>> [ 2.280537] mpt2sas_cm0: _base_event_notification: complete >>>>>> [ 2.281694] mpt2sas_cm0: LSISAS2008: FWVersion(20.00.04.00), ChipRevision(0x03), BiosVersion(07.39.00.00) >>>>>> [ 2.282196] mpt2sas_cm0: Protocol=( >>>>>> [ 2.282261] Initiator >>>>>> [ 2.282522] ,Target >>>>>> [ 2.282567] ), >>>>>> [ 2.282824] Capabilities=( >>>>>> [ 2.282877] TLR >>>>>> [ 2.283132] ,EEDP >>>>>> [ 2.283175] ,Snapshot Buffer >>>>>> [ 2.283444] ,Diag Trace Buffer >>>>>> [ 2.283502] ,Task Set Full >>>>>> [ 2.283774] ,NCQ >>>>>> [ 2.283816] ) >>>>>> [ 2.284350] scsi host0: Fusion MPT SAS Host >>>>>> [ 2.299028] mpt2sas_cm0: sending port enable !! >>>>>> [ 2.299540] mpt2sas_cm0: Discovery: (start) >>>>>> >>>>>> [ 2.299972] mpt2sas_cm0: SAS Enclosure Device Status Change >>>>>> [ 2.299984] mpt2sas_cm0: discovery event: (start) >>>>>> >>>>>> [ 2.300554] mpt2sas_cm0: SAS Topology Change List >>>>>> [ 2.300759] mpt2sas_cm0: Discovery: (stop) >>>>>> >>>>>> [ 2.301146] mpt2sas_cm0: Discovery: (start) >>>>>> >>>>>> [ 2.301535] mpt2sas_cm0: Discovery: (stop) >>>>>> >>>>>> [ 2.301927] mpt2sas_cm0: Discovery: (start) >>>>>> >>>>>> [ 2.302316] mpt2sas_cm0: Discovery: (stop) >>>>>> >>>>>> [ 2.302707] mpt2sas_cm0: Discovery: (start) >>>>>> >>>>>> [ 2.304908] mpt2sas_cm0: Discovery: (stop) >>>>>> >>>>>> [ 2.305297] mpt2sas_cm0: Discovery: (start) >>>>>> >>>>>> [ 2.306776] mpt2sas_cm0: Discovery: (stop) >>>>>> >>>>>> [ 2.307166] mpt2sas_cm0: Discovery: (start) >>>>>> >>>>>> [ 2.307559] mpt2sas_cm0: Discovery: (stop) >>>>>> >>>>>> [ 2.307948] mpt2sas_cm0: Discovery: (start) >>>>>> >>>>>> [ 2.308336] mpt2sas_cm0: Discovery: (stop) >>>>>> >>>>>> [ 2.311738] mpt2sas_cm0: host_add: handle(0x0001), sas_addr(0x500605b003683dd0), phys(8) >>>>>> [ 2.312097] mpt2sas_cm0: enclosure status change: (enclosure add) >>>>>> handle(0x0001), enclosure logical id(0x500605b003683dd0) number slots(0) >>>>>> [ 2.312551] mpt2sas_cm0: sas topology change: (responding) >>>>>> [ 2.312768] handle(0x0000), enclosure_handle(0x0001) start_phy(00), count(8) >>>>>> [ 2.313003] phy(01), attached_handle(0x0009): target add: link rate: new(0x0a), old(0x00) >>>>>> [ 2.313250] phy(02), attached_handle(0x000a): target add: link rate: new(0x09), old(0x00) >>>>>> [ 2.313498] phy(03), attached_handle(0x000b): target add: link rate: new(0x09), old(0x00) >>>>>> [ 2.313745] phy(04), attached_handle(0x000c): target add: link rate: new(0x09), old(0x00) >>>>>> [ 2.313992] phy(05), attached_handle(0x000d): target add: link rate: new(0x09), old(0x00) >>>>>> [ 2.314248] phy(06), attached_handle(0x000e): target add: link rate: new(0x09), old(0x00) >>>>>> [ 2.314495] phy(07), attached_handle(0x000f): target add: link rate: new(0x09), old(0x00) >>>>>> [ 2.314747] mpt2sas_cm0: updating handles for sas_host(0x500605b003683dd0) >>>>>> [ 2.316041] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x0009), sas_addr(0x4433221101000000) >>>>>> [ 2.316465] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 2) >>>>>> [ 2.317200] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000a), sas_addr(0x4433221102000000) >>>>>> [ 2.317669] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 1) >>>>>> [ 2.318431] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000b), sas_addr(0x4433221103000000) >>>>>> [ 2.318900] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 0) >>>>>> [ 2.319366] mpt2sas_cm0: _scsih_determine_boot_device: current_boot_device(0x4433221103000000) >>>>>> [ 2.320151] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000c), sas_addr(0x4433221104000000) >>>>>> [ 2.321371] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 7) >>>>>> [ 2.322137] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000d), sas_addr(0x4433221105000000) >>>>>> [ 2.322606] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 6) >>>>>> [ 2.323367] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000e), sas_addr(0x4433221106000000) >>>>>> [ 2.323834] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 5) >>>>>> [ 2.324602] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000f), sas_addr(0x4433221107000000) >>>>>> [ 2.325071] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 4) >>>>>> [ 2.325541] mpt2sas_cm0: discovery event: (stop) >>>>>> >>>>>> [ 2.326017] mpt2sas_cm0: discovery event: (start) >>>>>> >>>>>> [ 2.326492] mpt2sas_cm0: discovery event: (stop) >>>>>> >>>>>> [ 2.326975] mpt2sas_cm0: discovery event: (start) >>>>>> >>>>>> [ 2.327450] mpt2sas_cm0: discovery event: (stop) >>>>>> >>>>>> [ 2.327923] mpt2sas_cm0: discovery event: (start) >>>>>> >>>>>> [ 2.328396] mpt2sas_cm0: discovery event: (stop) >>>>>> >>>>>> [ 2.328868] mpt2sas_cm0: discovery event: (start) >>>>>> >>>>>> [ 2.329340] mpt2sas_cm0: discovery event: (stop) >>>>>> >>>>>> [ 2.329816] mpt2sas_cm0: discovery event: (start) >>>>>> >>>>>> [ 2.330316] mpt2sas_cm0: discovery event: (stop) >>>>>> >>>>>> [ 2.330797] mpt2sas_cm0: discovery event: (start) >>>>>> >>>>>> [ 2.331269] mpt2sas_cm0: discovery event: (stop) >>>>>> >>>>>> [ 2.331740] mpt2sas_cm0: port enable: complete from worker thread >>>>>> [ 2.350236] mpt2sas_cm0: port enable: SUCCESS >>>>>> [ 2.356432] scsi 0:0:0:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 >>>>>> [ 2.356683] scsi 0:0:0:0: SATA: handle(0x000b), sas_addr(0x4433221103000000), phy(3), device_name(0x5000c5000267c9f8) >>>>>> [ 2.357080] scsi 0:0:0:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(0) >>>>>> [ 2.357405] scsi 0:0:0:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>>> [ 2.383043] scsi 0:0:1:0: Direct-Access ATA Hitachi HDS5C302 A800 PQ: 0 ANSI: 6 >>>>>> [ 2.383296] scsi 0:0:1:0: SATA: handle(0x0009), sas_addr(0x4433221101000000), phy(1), device_name(0x5000cca369cdd311) >>>>>> [ 2.383684] scsi 0:0:1:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(2) >>>>>> [ 2.384028] scsi 0:0:1:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>>> [ 2.405088] scsi 0:0:2:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 >>>>>> [ 2.405346] scsi 0:0:2:0: SATA: handle(0x000a), sas_addr(0x4433221102000000), phy(2), device_name(0x5000c5000ccfbd32) >>>>>> [ 2.405735] scsi 0:0:2:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(1) >>>>>> [ 2.406082] scsi 0:0:2:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>>> [ 2.424125] scsi 0:0:3:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 >>>>>> [ 2.424373] scsi 0:0:3:0: SATA: handle(0x000c), sas_addr(0x4433221104000000), phy(4), device_name(0x5000c5000267abee) >>>>>> [ 2.424763] scsi 0:0:3:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(7) >>>>>> [ 2.425108] scsi 0:0:3:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>>> [ 2.444834] scsi 0:0:4:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 >>>>>> [ 2.445086] scsi 0:0:4:0: SATA: handle(0x000d), sas_addr(0x4433221105000000), phy(5), device_name(0x5000c50009c0e5e6) >>>>>> [ 2.445478] scsi 0:0:4:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(6) >>>>>> [ 2.445803] scsi 0:0:4:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>>> [ 2.464065] scsi 0:0:5:0: Direct-Access ATA ST3750330NS SN16 PQ: 0 ANSI: 6 >>>>>> [ 2.464312] scsi 0:0:5:0: SATA: handle(0x000e), sas_addr(0x4433221106000000), phy(6), device_name(0x5000c5003cb9ac10) >>>>>> [ 2.464699] scsi 0:0:5:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(5) >>>>>> [ 2.465048] scsi 0:0:5:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>>> [ 2.484016] scsi 0:0:6:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 >>>>>> [ 2.484266] scsi 0:0:6:0: SATA: handle(0x000f), sas_addr(0x4433221107000000), phy(7), device_name(0x5000c5000839b69e) >>>>>> [ 2.484655] scsi 0:0:6:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(4) >>>>>> [ 2.485001] scsi 0:0:6:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>>> [ 2.500660] mpt2sas_cm1: mpt3sas_base_attach >>>>>> [ 2.500861] mpt2sas_cm1: mpt3sas_base_map_resources >>>>>> [ 2.501599] mpt2sas_cm1: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3074748 kB) >>>>>> [ 2.501847] mpt2sas_cm1: _base_get_ioc_facts >>>>>> [ 2.502036] mpt2sas_cm1: _base_wait_for_iocstate >>>>>> [ 2.559080] offset:data >>>>>> [ 2.559318] [0x00]:03100200 >>>>>> [ 2.559552] [0x04]:00002300 >>>>>> [ 2.559785] [0x08]:00000000 >>>>>> [ 2.560020] [0x0c]:00000000 >>>>>> [ 2.560277] [0x10]:00000000 >>>>>> [ 2.560511] [0x14]:00010480 >>>>>> [ 2.560745] [0x18]:22130d68 >>>>>> [ 2.560978] [0x1c]:0001285c >>>>>> [ 2.561210] [0x20]:14000400 >>>>>> [ 2.561443] [0x24]:00000020 >>>>>> [ 2.561675] [0x28]:0100000f >>>>>> [ 2.561907] [0x2c]:000c000b >>>>>> [ 2.562139] [0x30]:003c0003 >>>>>> [ 2.562371] [0x34]:0020ffe0 >>>>>> [ 2.562602] [0x38]:00800122 >>>>>> [ 2.562839] [0x3c]:00000009 >>>>>> [ 2.563073] mpt2sas_cm1: hba queue depth(3432), max chains per io(128) >>>>>> [ 2.563355] mpt2sas_cm1: request frame size(128), reply frame size(128) >>>>>> [ 2.563745] mpt2sas_cm1: msix is supported, vector_count(1) >>>>>> [ 2.564016] mpt2sas_cm1: MSI-X vectors supported: 1, no of cores: 4, max_msix_vectors: 8 >>>>>> [ 2.564918] mpt2sas1-msix0: PCI-MSI-X enabled: IRQ 59 >>>>>> [ 2.566189] mpt2sas_cm1: iomem(0x00000000fd1fc000), mapped(0xffffc900000d8000), size(16384) >>>>>> [ 2.566498] mpt2sas_cm1: ioport(0x0000000000007000), size(256) >>>>>> [ 2.567328] mpt2sas_cm1: _base_get_ioc_facts >>>>>> [ 2.567583] mpt2sas_cm1: _base_wait_for_iocstate >>>>>> [ 2.625125] offset:data >>>>>> [ 2.625364] [0x00]:03100200 >>>>>> [ 2.625597] [0x04]:00002300 >>>>>> [ 2.625830] [0x08]:00000000 >>>>>> [ 2.626064] [0x0c]:00000000 >>>>>> [ 2.626296] [0x10]:00000000 >>>>>> [ 2.626529] [0x14]:00010480 >>>>>> [ 2.626769] [0x18]:22130d68 >>>>>> [ 2.627002] [0x1c]:0001285c >>>>>> [ 2.627235] [0x20]:14000400 >>>>>> [ 2.627467] [0x24]:00000020 >>>>>> [ 2.627702] [0x28]:0100000f >>>>>> [ 2.627936] [0x2c]:000c000b >>>>>> [ 2.628170] [0x30]:003c0003 >>>>>> [ 2.628403] [0x34]:0020ffe0 >>>>>> [ 2.628638] [0x38]:00800122 >>>>>> [ 2.628872] [0x3c]:00000009 >>>>>> [ 2.629107] mpt2sas_cm1: hba queue depth(3432), max chains per io(128) >>>>>> [ 2.629388] mpt2sas_cm1: request frame size(128), reply frame size(128) >>>>>> [ 2.629671] mpt2sas_cm1: _base_make_ioc_ready >>>>>> [ 2.629928] mpt2sas_cm1: _base_get_port_facts >>>>>> [ 2.660127] offset:data >>>>>> [ 2.660389] [0x00]:05070000 >>>>>> [ 2.660623] [0x04]:00000000 >>>>>> [ 2.660858] [0x08]:00000000 >>>>>> [ 2.661093] [0x0c]:00000000 >>>>>> [ 2.661326] [0x10]:00000000 >>>>>> [ 2.661562] [0x14]:00003000 >>>>>> [ 2.661796] [0x18]:00000078 >>>>>> [ 2.664346] mpt2sas_cm1: _base_allocate_memory_pools >>>>>> [ 2.664608] mpt2sas_cm1: scatter gather: sge_in_main_msg(3), sge_per_chain(15), sge_per_io(128), chains_per_io(9) >>>>>> [ 2.665142] mpt2sas_cm1: reply post free pool (0xffff8800b8b10000): depth(6944),element_size(8), pool_size(54 kB) >>>>>> [ 2.666671] mpt2sas_cm1: reply_post_free_dma = (0xb8b10000) >>>>>> [ 2.666954] mpt2sas_cm1: scsi host: can_queue depth (3307) >>>>>> [ 2.667311] mpt2sas_cm1: request pool(0xffff8800b8b80000): depth(3432), frame_size(128), pool_size(429 kB) >>>>>> [ 2.667813] mpt2sas_cm1: request pool: dma(0xb8b80000) >>>>>> [ 2.668080] mpt2sas_cm1: scsiio(0xffff8800b8b80000): depth(3307) >>>>>> [ 2.674131] mpt2sas_cm1: chain pool depth(29763), frame_size(128), pool_size(3720 kB) >>>>>> [ 2.674448] mpt2sas_cm1: hi_priority(0xffff8800b8be7600): depth(60), start smid(3308) >>>>>> [ 2.674750] mpt2sas_cm1: internal(0xffff8800b8be9400): depth(65), start smid(3368) >>>>>> [ 2.675105] mpt2sas_cm1: sense pool(0xffff8800b8100000): depth(3307), element_size(96), pool_size(310 kB) >>>>>> [ 2.675605] mpt2sas_cm1: sense_dma(0xb8100000) >>>>>> [ 2.675944] mpt2sas_cm1: reply pool(0xffff8800b8180000): depth(3496), frame_size(128), pool_size(437 kB) >>>>>> [ 2.676443] mpt2sas_cm1: reply_dma(0xb8180000) >>>>>> [ 2.676702] mpt2sas_cm1: reply_free pool(0xffff8800b80a0000): depth(3496), element_size(4), pool_size(13 kB) >>>>>> [ 2.677124] mpt2sas_cm1: reply_free_dma (0xb80a0000) >>>>>> [ 2.677322] mpt2sas_cm1: config page(0xffff8800b807f000): size(512) >>>>>> [ 2.677532] mpt2sas_cm1: config_page_dma(0xb807f000) >>>>>> [ 2.677728] mpt2sas_cm1: Allocated physical memory: size(4964 kB) >>>>>> [ 2.677936] mpt2sas_cm1: Current Controller Queue Depth(3307),Max Controller Queue Depth(3432) >>>>>> [ 2.678304] mpt2sas_cm1: Scatter Gather Elements per IO(128) >>>>>> [ 2.678514] mpt2sas_cm1: _base_make_ioc_operational >>>>>> [ 2.679081] mpt2sas_cm1: _base_send_ioc_init >>>>>> [ 2.679275] offset:data >>>>>> [ 2.679448] [0x00]:02000004 >>>>>> [ 2.679625] [0x04]:00000000 >>>>>> [ 2.679805] [0x08]:00000000 >>>>>> [ 2.681200] [0x0c]:23000200 >>>>>> [ 2.681377] [0x10]:00000000 >>>>>> [ 2.681554] [0x14]:00000000 >>>>>> [ 2.681729] [0x18]:00200000 >>>>>> [ 2.681906] [0x1c]:0da81b20 >>>>>> [ 2.682082] [0x20]:00000000 >>>>>> [ 2.682259] [0x24]:00000000 >>>>>> [ 2.682435] [0x28]:b8b80000 >>>>>> [ 2.682611] [0x2c]:00000000 >>>>>> [ 2.682787] [0x30]:b8b10000 >>>>>> [ 2.682963] [0x34]:00000000 >>>>>> [ 2.683139] [0x38]:b80a0000 >>>>>> [ 2.683314] [0x3c]:00000000 >>>>>> [ 2.683489] [0x40]:98597011 >>>>>> [ 2.683665] [0x44]:00000153 >>>>>> [ 2.729849] offset:data >>>>>> [ 2.730089] [0x00]:02050004 >>>>>> [ 2.730349] [0x04]:00000000 >>>>>> [ 2.730586] [0x08]:00000000 >>>>>> [ 2.730822] [0x0c]:00000000 >>>>>> [ 2.731058] [0x10]:00000000 >>>>>> [ 2.731295] mpt2sas_cm1: _base_event_notification >>>>>> [ 2.731606] mpt2sas_cm1: _base_event_notification: complete >>>>>> [ 2.732501] mpt2sas_cm1: LSISAS2008: FWVersion(20.00.04.00), ChipRevision(0x02), BiosVersion(07.39.00.00) >>>>>> [ 2.733010] mpt2sas_cm1: Protocol=( >>>>>> [ 2.733074] Initiator >>>>>> [ 2.733339] ,Target >>>>>> [ 2.733384] ), >>>>>> [ 2.733642] Capabilities=( >>>>>> [ 2.733696] TLR >>>>>> [ 2.733952] ,EEDP >>>>>> [ 2.733995] ,Snapshot Buffer >>>>>> [ 2.734268] ,Diag Trace Buffer >>>>>> [ 2.734326] ,Task Set Full >>>>>> [ 2.734595] ,NCQ >>>>>> [ 2.734637] ) >>>>>> [ 2.735155] scsi host1: Fusion MPT SAS Host >>>>>> [ 2.749047] mpt2sas_cm1: sending port enable !! >>>>>> [ 2.749563] mpt2sas_cm1: Discovery: (start) >>>>>> >>>>>> [ 2.749989] mpt2sas_cm1: SAS Enclosure Device Status Change >>>>>> [ 2.750001] mpt2sas_cm1: discovery event: (start) >>>>>> >>>>>> [ 2.750578] mpt2sas_cm1: SAS Topology Change List >>>>>> [ 2.750788] mpt2sas_cm1: Discovery: (stop) >>>>>> >>>>>> [ 2.751181] mpt2sas_cm1: Discovery: (start) >>>>>> >>>>>> [ 2.751571] mpt2sas_cm1: Discovery: (stop) >>>>>> >>>>>> [ 2.752002] mpt2sas_cm1: Discovery: (start) >>>>>> >>>>>> [ 2.752391] mpt2sas_cm1: Discovery: (stop) >>>>>> >>>>>> [ 2.752779] mpt2sas_cm1: Discovery: (start) >>>>>> >>>>>> [ 2.754205] mpt2sas_cm1: Discovery: (stop) >>>>>> >>>>>> [ 2.754593] mpt2sas_cm1: Discovery: (start) >>>>>> >>>>>> [ 2.754983] mpt2sas_cm1: Discovery: (stop) >>>>>> >>>>>> [ 2.755371] mpt2sas_cm1: Discovery: (start) >>>>>> >>>>>> [ 2.755762] mpt2sas_cm1: Discovery: (stop) >>>>>> >>>>>> [ 2.759602] mpt2sas_cm1: host_add: handle(0x0001), sas_addr(0x500605b0026f79b0), phys(8) >>>>>> [ 2.759969] mpt2sas_cm1: enclosure status change: (enclosure add) >>>>>> handle(0x0001), enclosure logical id(0x500605b0026f79b0) number slots(0) >>>>>> [ 2.760407] mpt2sas_cm1: sas topology change: (responding) >>>>>> [ 2.760612] handle(0x0000), enclosure_handle(0x0001) start_phy(00), count(8) >>>>>> [ 2.760834] phy(02), attached_handle(0x000e): target add: link rate: new(0x0a), old(0x00) >>>>>> [ 2.761066] phy(03), attached_handle(0x000b): target add: link rate: new(0x0a), old(0x00) >>>>>> [ 2.761304] phy(04), attached_handle(0x000d): target add: link rate: new(0x09), old(0x00) >>>>>> [ 2.761538] phy(05), attached_handle(0x0009): target add: link rate: new(0x09), old(0x00) >>>>>> [ 2.761771] phy(06), attached_handle(0x000a): target add: link rate: new(0x09), old(0x00) >>>>>> [ 2.762002] phy(07), attached_handle(0x000c): target add: link rate: new(0x09), old(0x00) >>>>>> [ 2.762235] mpt2sas_cm1: updating handles for sas_host(0x500605b0026f79b0) >>>>>> [ 2.763653] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x000e), sas_addr(0x4433221102000000) >>>>>> [ 2.764036] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 1) >>>>>> [ 2.764772] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x000b), sas_addr(0x4433221103000000) >>>>>> [ 2.765147] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 0) >>>>>> [ 2.765891] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x000d), sas_addr(0x4433221104000000) >>>>>> [ 2.767250] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 7) >>>>>> [ 2.768009] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x0009), sas_addr(0x4433221105000000) >>>>>> [ 2.768394] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 6) >>>>>> [ 2.769136] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x000a), sas_addr(0x4433221106000000) >>>>>> [ 2.769510] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 5) >>>>>> [ 2.769888] mpt2sas_cm1: _scsih_determine_boot_device: current_boot_device(0x4433221106000000) >>>>>> [ 2.770641] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x000c), sas_addr(0x4433221107000000) >>>>>> [ 2.771025] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 4) >>>>>> [ 2.771405] mpt2sas_cm1: discovery event: (stop) >>>>>> >>>>>> [ 2.771788] mpt2sas_cm1: discovery event: (start) >>>>>> >>>>>> [ 2.772172] mpt2sas_cm1: discovery event: (stop) >>>>>> >>>>>> [ 2.772554] mpt2sas_cm1: discovery event: (start) >>>>>> >>>>>> [ 2.772942] mpt2sas_cm1: discovery event: (stop) >>>>>> >>>>>> [ 2.773326] mpt2sas_cm1: discovery event: (start) >>>>>> >>>>>> [ 2.773709] mpt2sas_cm1: discovery event: (stop) >>>>>> >>>>>> [ 2.774090] mpt2sas_cm1: discovery event: (start) >>>>>> >>>>>> [ 2.774474] mpt2sas_cm1: discovery event: (stop) >>>>>> >>>>>> [ 2.774855] mpt2sas_cm1: discovery event: (start) >>>>>> >>>>>> [ 2.775237] mpt2sas_cm1: discovery event: (stop) >>>>>> >>>>>> [ 2.775619] mpt2sas_cm1: port enable: complete from worker thread >>>>>> [ 2.780192] mpt2sas_cm1: port enable: SUCCESS >>>>>> [ 2.782404] scsi 1:0:0:0: Direct-Access ATA Hitachi HDP72505 A5BA PQ: 0 ANSI: 6 >>>>>> [ 2.782651] scsi 1:0:0:0: SATA: handle(0x000a), sas_addr(0x4433221106000000), phy(6), device_name(0x5000cca34dc05584) >>>>>> [ 2.783039] scsi 1:0:0:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(5) >>>>>> [ 2.783390] scsi 1:0:0:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>>> [ 2.803032] scsi 1:0:1:0: Direct-Access ATA ST8000AS0002-1NA AR15 PQ: 0 ANSI: 6 >>>>>> [ 2.803272] scsi 1:0:1:0: SATA: handle(0x000e), sas_addr(0x4433221102000000), phy(2), device_name(0x5000c500908f1d05) >>>>>> [ 2.803660] scsi 1:0:1:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(1) >>>>>> [ 2.803981] scsi 1:0:1:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>>> [ 2.821712] scsi 1:0:2:0: Direct-Access ATA ST3000DM001-1CH1 CC43 PQ: 0 ANSI: 6 >>>>>> [ 2.821963] scsi 1:0:2:0: SATA: handle(0x000b), sas_addr(0x4433221103000000), phy(3), device_name(0x5000c5004dfd2a8a) >>>>>> [ 2.822352] scsi 1:0:2:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(0) >>>>>> [ 2.822694] scsi 1:0:2:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>>> [ 2.844233] scsi 1:0:3:0: Direct-Access ATA ST3500320NS SN16 PQ: 0 ANSI: 6 >>>>>> [ 2.844483] scsi 1:0:3:0: SATA: handle(0x000d), sas_addr(0x4433221104000000), phy(4), device_name(0x5000c50009dca65b) >>>>>> [ 2.844870] scsi 1:0:3:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(7) >>>>>> [ 2.845216] scsi 1:0:3:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>>> [ 2.868963] scsi 1:0:4:0: Direct-Access ATA SAMSUNG HD401LJ 0-15 PQ: 0 ANSI: 6 >>>>>> [ 2.870994] scsi 1:0:4:0: SATA: handle(0x0009), sas_addr(0x4433221105000000), phy(5), device_name(0x695d550daf678093) >>>>>> [ 2.871382] scsi 1:0:4:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(6) >>>>>> [ 2.871728] scsi 1:0:4:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>>> [ 2.894004] scsi 1:0:5:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 >>>>>> [ 2.894257] scsi 1:0:5:0: SATA: handle(0x000c), sas_addr(0x4433221107000000), phy(7), device_name(0x5000c5000266bb02) >>>>>> [ 2.894646] scsi 1:0:5:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(4) >>>>>> [ 2.894972] scsi 1:0:5:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>> >>>>> I don't see a clear pattern yet, but I suspect warm rebooting >=4.2 >>>>> after having run 4.1.x leads to sucessful driver inits. But I also >>>>> remember having had cold boots, with kernels >=4.2 that worked fine >>>>> (obviously not all of the time). <=4.1.20 kernels on the other hand boot >>>>> fine every single time. >>>>> >>>>> Interestingly the igb driver (ethernet) seems to be acting up at least >>>>> with 4.5.0 on exactly the same boots when mpt2sas init fails. I don't >>>>> know whether this could be connected or not (I just became aware of this >>>>> coincidence). >>>>> >>>>> >>>>> --- >>>>> Matthias >>>>> >>>>> >>>>> Am 21.03.2016 um 05:53 schrieb Sreekanth Reddy: >>>>>> Hi Matthias, >>>>>> >>>>>> Can you please share us the driver logs with driver logging_level set >>>>>> to 0x3f8. So that we can get more info from this log. >>>>>> >>>>>> Thanks, >>>>>> Sreekanth >>>>>> >>>>>> On Mon, Mar 21, 2016 at 1:44 AM, Matthias Prager >>>>>> <linux@matthiasprager.de> wrote: >>>>>>> Hello, >>>>>>> >>>>>>> I don't know what's the correct procedure, whether I should file a bug or first report this issue on the kernel mailing-list. So please feel free to tell me to open a ticket in the bugtracker (bugzilla.kernel.org?). >>>>>>> >>>>>>> But first let me present the issue I encounter: >>>>>>> >>>>>>> Kernels >= 4.2 (4.2.1 was the first on I tried, but also 4.3, 4.4 and 4.5) fail to load the mpt2sas driver on most (but not all) boots. Kernels <= 4.1.x work fine every single time (4.1.19 was the latest I tried, also 3.18.29). >>>>>>> >>>>>>> Here is the dmesg output for a failed driver init with Kernel 4.5.0: >>>>>>>> [ 2.068313] mpt3sas version 09.102.00.00 loaded >>>>>>>> [ 2.069412] mpt2sas_cm0: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3074748 kB) >>>>>>>> [ 2.125260] mpt2sas_cm0: MSI-X vectors supported: 1, no of cores: 4, max_msix_vectors: -1 >>>>>>>> [ 2.125996] mpt2sas0-msix0: PCI-MSI-X enabled: IRQ 58 >>>>>>>> [ 2.126199] mpt2sas_cm0: iomem(0x00000000fd4fc000), mapped(0xffffc900000d0000), size(16384) >>>>>>>> [ 2.126430] mpt2sas_cm0: ioport(0x0000000000004000), size(256) >>>>>>>> [ 2.216371] mpt2sas_cm0: Allocated physical memory: size(4964 kB) >>>>>>>> [ 2.216600] mpt2sas_cm0: Current Controller Queue Depth(3307),Max Controller Queue Depth(3432) >>>>>>>> [ 2.217004] mpt2sas_cm0: Scatter Gather Elements per IO(128) >>>>>>>> [ 5.086959] floppy0: no floppy controllers found >>>>>>>> [ 32.256720] mpt2sas_cm0: _base_event_notification: timeout >>>>>>>> [ 32.256940] mf: >>>>>>>> >>>>>>>> [ 32.257106] 07000000 >>>>>>>> [ 32.257302] 00000000 >>>>>>>> [ 32.257337] 00000000 >>>>>>>> [ 32.257533] 00000000 >>>>>>>> [ 32.257568] 00000000 >>>>>>>> [ 32.257764] 0f2f7fff >>>>>>>> [ 32.257800] ffffff7c >>>>>>>> [ 32.257995] ffffffff >>>>>>>> [ 32.258031] >>>>>>>> >>>>>>>> [ 32.258352] ffffffff >>>>>>>> [ 32.258387] 00000000 >>>>>>>> [ 32.258582] 00000000 >>>>>>>> >>>>>>>> [ 32.258950] mpt2sas_cm0: sending message unit reset !! >>>>>>>> [ 32.260688] mpt2sas_cm0: message unit reset: SUCCESS >>>>>>>> [ 32.325956] mpt2sas_cm0: failure at drivers/scsi/mpt3sas/mpt3sas_scsih.c:8592/_scsih_probe()! >>>>>>> >>>>>>> For comparison here is a dmesg output for a successful boot on Kernel 4.1.15: >>>>>>>> [ 2.035568] mpt2sas version 20.100.00.00 loaded >>>>>>>> [ 2.037243] mpt2sas0: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (2046352 kB) >>>>>>>> [ 2.755374] mpt2sas0: MSI-X vectors supported: 1, no of cores: 3, max_msix_vectors: 8 >>>>>>>> [ 2.756377] mpt2sas0-msix0: PCI-MSI-X enabled: IRQ 58 >>>>>>>> [ 2.756708] mpt2sas0: iomem(0x00000000fd5fc000), mapped(0xffffc900000d0000), size(16384) >>>>>>>> [ 2.757083] mpt2sas0: ioport(0x0000000000004000), size(256) >>>>>>>> [ 3.842944] mpt2sas0: Allocated physical memory: size(4964 kB) >>>>>>>> [ 3.843303] mpt2sas0: Current Controller Queue Depth(3307), Max Controller Queue Depth(3432) >>>>>>>> [ 3.843717] mpt2sas0: Scatter Gather Elements per IO(128) >>>>>>>> [ 4.415980] mpt2sas0: LSISAS2008: FWVersion(20.00.04.00), ChipRevision(0x03), BiosVersion(07.39.00.00) >>>>>>>> [ 4.416618] mpt2sas0: Protocol=(Initiator,Target), Capabilities=(TLR,EEDP,Snapshot Buffer,Diag Trace Buffer,Task Set Full,NCQ) >>>>>>>> [ 4.417846] scsi host0: Fusion MPT SAS Host >>>>>>>> [ 4.436865] mpt2sas0: sending port enable !! >>>>>>>> [ 4.440460] mpt2sas0: host_add: handle(0x0001), sas_addr(0xxxxxxxxxxxxxxxxx), phys(8) >>>>>>>> >>>>>>>> ... >>>>>>>> [ 4.444045] scsi 0:0:0:0: Direct-Access ATA Hitachi HDS5C302 A800 PQ: 0 ANSI: 6 >>>>>>>> [ 4.444338] scsi 0:0:0:0: SATA: handle(0x0009), sas_addr(0xxxxxxxxxxxxxxxxx), phy(1), device_name(0xxxxxxxxxxxxxxxxx) >>>>>>>> [ 4.444823] scsi 0:0:0:0: SATA: enclosure_logical_id(0xxxxxxxxxxxxxxxxx), slot(2) >>>>>>>> [ 4.445197] scsi 0:0:0:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>>>>> ... (n times for n drives) >>>>>>>> >>>>>>>> [ 4.515443] mpt2sas0: port enable: SUCCESS >>>>>>> >>>>>>> >>>>>>> The Controller(s) are all Avego/LSI 9211-8i running the latest version of IT firmware (v20.00.04.00). These are passed through to a gentoo-linux VM on an ESXi 5.1 host (latest patchlevel). I have two of these systems (one production one testing) with nearly identical hardware (Supermicro X8DTi-F boards with 2x Intel Westmere CPUs). I also have an older set of systems running the same software config (Intel S3200SHLC boards with single Core2Quad) which exhibit the same buggy behavior. >>>>>>> >>>>>>> The 'uname -a' line on the current testing system looks like this: >>>>>>>> Linux pserver2 4.1.19-gentoo #4 SMP Thu Mar 17 16:02:48 CET 2016 x86_64 Intel(R) Xeon(R) CPU E5506 @ 2.13GHz GenuineIntel GNU/Linux >>>>>>> p >>>>>>> >>>>>>> There seem to be other people with similar issues: >>>>>>> <https://bbs.archlinux.org/viewtopic.php?id=209495> >>>>>>> >>>>>>> Any thoughts? >>>>>>> >>>>>>> --- >>>>>>> Matthias >>>>> >> ^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [BUG] mpt2sas: driver init fails on kernel >=4.2 for 9211-8i IT 2016-03-22 21:02 ` Matthias Prager @ 2016-03-24 2:06 ` Matthias Prager 2016-03-24 6:06 ` Thomas Gleixner 0 siblings, 1 reply; 13+ messages in thread From: Matthias Prager @ 2016-03-24 2:06 UTC (permalink / raw) To: Sreekanth Reddy; +Cc: linux-scsi, Matthias Prager, Jiang Liu, Thomas Gleixner Hi Sreekanth, I have bisected the issue down to commit <https://git.kernel.org/cgit/linux/kernel/git/stable/linux-stable.git/commit/?id=52f518a3a7c2f80551a38d38be28bc9f335e713c> "x86/MSI: Use hierarchical irqdomains to manage MSI interrupts". The timeout happens reliably after two warm boots with a 'bad' kernel after coming from a 'good' kernel, and also after one cold boot with a 'bad' kernel (meaning cold booting a 'bad' kernel leads directly to the timeout and warm booting needs a second run to produce the timeout). I haven't tested bare metal yet - I can do that tomorrow if necessary. Here is the bisect log: > Bisecting: a merge base must be tested > [b953c0d234bc72e8489d3bf51a276c5c4ec85345] Linux 4.1 > Bisecting: 7475 revisions left to test after this (roughly 13 steps) > [c11d716218910c3aa2bac1bb641e6086ad649555] Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc > Bisecting: 4008 revisions left to test after this (roughly 12 steps) > [8a8c35fadfaf55629a37ef1a8ead1b8fb32581d2] mm: kmemleak_alloc_percpu() should follow the gfp from per_alloc() > Bisecting: 1680 revisions left to test after this (roughly 11 steps) > [10b4b096d0c7e9f1b5f84c2a0658b2963e1e6ed0] Merge tag 'gpio-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio > Bisecting: 793 revisions left to test after this (roughly 10 steps) > [e75c73ad64478c12b3a44b86a3e7f62a4f65b93e] Merge branch 'x86-fpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip > Bisecting: 380 revisions left to test after this (roughly 9 steps) > [407a2c720556e8e340e06f6a7174f5d6d80cf9ea] Merge branch 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip > Bisecting: 210 revisions left to test after this (roughly 8 steps) > [539f5113650068ba221197f190267ab727296ef5] x86/asm/entry/64: Disentangle error_entry/exit gsbase/ebx/usermode code > Bisecting: 98 revisions left to test after this (roughly 7 steps) > [191a66353b22fad8ac89404ab4c929cbe7b0afb2] Merge branch 'x86/asm' into x86/apic, to resolve a conflict > Bisecting: 51 revisions left to test after this (roughly 6 steps) > [099c5c03487f6bca30c628e14e666788dd61fb33] irq_remapping/vt-d: Move struct irq_2_iommu into intel_irq_remapping.c > Bisecting: 25 revisions left to test after this (roughly 5 steps) > [90d84fe95dd6b418383aa0e0e5cace8f1b1e7e30] x86/MSI: Replace msi_update_msg() with irq_chip_compose_msi_msg() > Bisecting: 12 revisions left to test after this (roughly 4 steps) > [3cb96f0c97330834929abe9bd2ca3c252a83def0] x86/hpet: Enhance HPET IRQ to support hierarchical irqdomains > Bisecting: 6 revisions left to test after this (roughly 3 steps) > [b1855c752e67d1125d41fadb499014b49a245db8] x86/MSI: Clean up unused MSI related code and interfaces > Bisecting: 2 revisions left to test after this (roughly 2 steps) > [2b43817e481da9f5118adb56aef46b3f0298c685] irq_remapping/vt-d: Clean up unused MSI related code > Bisecting: 0 revisions left to test after this (roughly 1 step) > [80aa283364a17998dceb577bd185e3380b927544] x86/irq: Directly call native_compose_msi_msg() for DMAR IRQ > Bisecting: 0 revisions left to test after this (roughly 0 steps) > [52f518a3a7c2f80551a38d38be28bc9f335e713c] x86/MSI: Use hierarchical irqdomains to manage MSI interrupts > 52f518a3a7c2f80551a38d38be28bc9f335e713c is the first bad commit > commit 52f518a3a7c2f80551a38d38be28bc9f335e713c > Author: Jiang Liu <jiang.liu@linux.intel.com> > Date: Mon Apr 13 14:11:35 2015 +0800 > > x86/MSI: Use hierarchical irqdomains to manage MSI interrupts > > Enhance MSI code to support hierarchical irqdomains, it helps to make > the architecture more clear. > > Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com> > Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> > Cc: David Cohen <david.a.cohen@linux.intel.com> > Cc: Sander Eikelenboom <linux@eikelenboom.it> > Cc: David Vrabel <david.vrabel@citrix.com> > Cc: Tony Luck <tony.luck@intel.com> > Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> > Cc: iommu@lists.linux-foundation.org > Cc: Joerg Roedel <jroedel@suse.de> > Cc: Bjorn Helgaas <bhelgaas@google.com> > Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> > Cc: Rafael J. Wysocki <rjw@rjwysocki.net> > Cc: Randy Dunlap <rdunlap@infradead.org> > Cc: Yinghai Lu <yinghai@kernel.org> > Cc: Borislav Petkov <bp@alien8.de> > Cc: Dimitri Sivanich <sivanich@sgi.com> > Cc: Joerg Roedel <joro@8bytes.org> > Link: http://lkml.kernel.org/r/1428905519-23704-14-git-send-email-jiang.liu@linux.intel.com > Signed-off-by: Thomas Gleixner <tglx@linutronix.de> > > :040000 040000 786bcad9a3fad413e0b744e2cfa20da7ff402db6 22618cac66dee85a7752bb3af81169fff3a242d8 M arch > :040000 040000 acee54015803d4cd52d582a9e5e93aa56ad08482 40d2c7a02c0f8677e596c98c936404b2211336a3 M drivers --- Matthias Am 22.03.2016 um 22:02 schrieb Matthias Prager: > Hi Sreekanth, > > Am 22.03.2016 um 11:52 schrieb Sreekanth Reddy: >> Hi Matthias, >> >> Thanks for providing detail explanation. >> >> Currently I am trying to reproduce this issue locally. I have used the >> same HBA card but still I am not able to reproduce this issue on 4.5 >> kernel. >> >> I will try for few more times and I will also try to get the diff >> between 4.1 to 4.5 kernels w.r.t msix vectors support. > I will try to bisect this tomorrow. And I will try to reproduce this > outside the VM environment on bare metal. > >> >> Meanwhile can you please provide me the output of "lspci -vvv" command >> for LSI SAS2 HBA's and also hexdump of config sysfs parameter for SAS2 >> pci device. I need this data to be collected before "timeout" print is >> observed, or in the mpt3sas_base.c file and in the >> mpt3sas_base_attach(). return from mpt3sas_base_attach() function if >> return value of mpt3sas_base_map_resources() is non zero instead of >> freeing the resources, as shown below >> >> --------------------------------------------------------------------------- >> r = mpt3sas_base_map_resources(ioc); >> if (r) >> - goto out_free_resources; >> + return r; >> ----------------------------------------------------------------------------- > I will get you this data tomorrow too. > >> >> Also are you sure that this issue won't occur on less than 4.1 kernel? > Yes definitely - I never observed these timeouts with any kernel > <=4.1.20, and I started seeing them from kernel 4.2.1 onward (I haven't > actually tested 4.2.0 yet). > >> >> Thanks, >> Sreekanth >> >> On Mon, Mar 21, 2016 at 10:00 PM, Matthias Prager >> <linux@matthiasprager.de> wrote: >>> Am 21.03.2016 um 16:52 schrieb Matthias Prager: >>>> Hi Sreekanth, >>>> >>>> thanks for digging into this issue. Regarding the 4.5.0 after 4.1.20 >>>> boot statement, I will try to express myself better: >>>> >>>> I first started the system with the 4.1.20 kernel. Then I issued an >>>> 'init 6' warm-reboot and chose to boot the 4.5.0 kernel. This procedure >>>> often works (i.e. I'm able to boot the newer kernels (>=4.2) this way >>>> with mpt2sas initializing just fine). >>> One small addition: warm-rebooting kernel 4.5.0 from kernel 4.5.0 >>> reliably leads to this issue manifesting (mpt2sas driver not initializing). >>> >>>> >>>> I will try the msix_disable parameter and report back. Maybe kernel >>>> version 4.2 broke interrupt handling somehow? >>> With the msix_disable parameter set kernels 4.5.0, 4.4.5, 4.3.3 and >>> 4.2.1 boot without the mpt2sas init issue. I also tried the pci=nomsi >>> paremeter instead, which also works fine. >>> >>> The igb ethernet-driver issue I mentioned as possibly related has not >>> changed with pci=nomsi. So I'm assuming it is not the same issue, but >>> possibly related, since it also occurs on kernels >=4.2. >>> >>>> >>>> --- >>>> Matthias >>>> >>>> >>>> Am 21.03.2016 um 14:59 schrieb Sreekanth Reddy: >>>>> Hi Matthias, >>>>> >>>>> Thanks for providing the logs. In these logs, I am not observing any >>>>> such a prints which should be suspected for this issue. >>>>> >>>>> Can you please try once by setting mpt3sas driver's "msix_disable" >>>>> module parameter to one. >>>>> >>>>> Also, can you please elaborate below statement for me, I am not able >>>>> understand this statement >>>>> "I managed to boot the same 4.5.0 kernel successfully after warm >>>>> rebooting from 4.1.20" >>>>> >>>>> Thanks, >>>>> Sreekanth >>>>> >>>>> On Mon, Mar 21, 2016 at 2:48 PM, Matthias Prager >>>>> <linux@matthiasprager.de> wrote: >>>>>> Hi Sreekanth, >>>>>> >>>>>> thank you for replying so quickly. Here are the logs you requested >>>>>> (kernel 4.5.0): >>>>>> >>>>>>> [ 2.083177] mpt3sas version 09.102.00.00 loaded >>>>>>> [ 2.083757] mpt2sas_cm0: mpt3sas_base_attach >>>>>>> [ 2.083956] mpt2sas_cm0: mpt3sas_base_map_resources >>>>>>> [ 2.084708] mpt2sas_cm0: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3074748 kB) >>>>>>> [ 2.084964] mpt2sas_cm0: _base_get_ioc_facts >>>>>>> [ 2.085154] mpt2sas_cm0: _base_wait_for_iocstate >>>>>>> [ 2.140893] offset:data >>>>>>> [ 2.141082] [0x00]:03100200 >>>>>>> [ 2.141257] [0x04]:00002300 >>>>>>> [ 2.141432] [0x08]:00000000 >>>>>>> [ 2.141606] [0x0c]:00000000 >>>>>>> [ 2.141780] [0x10]:00000000 >>>>>>> [ 2.141955] [0x14]:00010480 >>>>>>> [ 2.142129] [0x18]:22130d68 >>>>>>> [ 2.142303] [0x1c]:0001285c >>>>>>> [ 2.142477] [0x20]:14000400 >>>>>>> [ 2.142651] [0x24]:00000020 >>>>>>> [ 2.142825] [0x28]:0100000f >>>>>>> [ 2.143000] [0x2c]:000c000b >>>>>>> [ 2.143174] [0x30]:003c0003 >>>>>>> [ 2.143349] [0x34]:0020ffe0 >>>>>>> [ 2.143544] [0x38]:00800122 >>>>>>> [ 2.143719] [0x3c]:00000009 >>>>>>> [ 2.143895] mpt2sas_cm0: hba queue depth(3432), max chains per io(128) >>>>>>> [ 2.144106] mpt2sas_cm0: request frame size(128), reply frame size(128) >>>>>>> [ 2.144397] mpt2sas_cm0: msix is supported, vector_count(1) >>>>>>> [ 2.144600] mpt2sas_cm0: MSI-X vectors supported: 1, no of cores: 4, max_msix_vectors: -1 >>>>>>> [ 2.145161] mpt2sas0-msix0: PCI-MSI-X enabled: IRQ 58 >>>>>>> [ 2.145361] mpt2sas_cm0: iomem(0x00000000fd4fc000), mapped(0xffffc900000d0000), size(16384) >>>>>>> [ 2.145591] mpt2sas_cm0: ioport(0x0000000000004000), size(256) >>>>>>> [ 2.146206] mpt2sas_cm0: _base_get_ioc_facts >>>>>>> [ 2.146397] mpt2sas_cm0: _base_wait_for_iocstate >>>>>>> [ 2.202087] offset:data >>>>>>> [ 2.202281] [0x00]:03100200 >>>>>>> [ 2.202456] [0x04]:00002300 >>>>>>> [ 2.202631] [0x08]:00000000 >>>>>>> [ 2.202805] [0x0c]:00000000 >>>>>>> [ 2.202980] [0x10]:00000000 >>>>>>> [ 2.203154] [0x14]:00010480 >>>>>>> [ 2.203328] [0x18]:22130d68 >>>>>>> [ 2.203521] [0x1c]:0001285c >>>>>>> [ 2.203695] [0x20]:14000400 >>>>>>> [ 2.203870] [0x24]:00000020 >>>>>>> [ 2.204044] [0x28]:0100000f >>>>>>> [ 2.204219] [0x2c]:000c000b >>>>>>> [ 2.204394] [0x30]:003c0003 >>>>>>> [ 2.204571] [0x34]:0020ffe0 >>>>>>> [ 2.204746] [0x38]:00800122 >>>>>>> [ 2.204926] [0x3c]:00000009 >>>>>>> [ 2.205102] mpt2sas_cm0: hba queue depth(3432), max chains per io(128) >>>>>>> [ 2.205314] mpt2sas_cm0: request frame size(128), reply frame size(128) >>>>>>> [ 2.205528] mpt2sas_cm0: _base_make_ioc_ready >>>>>>> [ 2.205719] mpt2sas_cm0: _base_get_port_facts >>>>>>> [ 2.234205] offset:data >>>>>>> [ 2.234397] [0x00]:05070000 >>>>>>> [ 2.234573] [0x04]:00000000 >>>>>>> [ 2.234748] [0x08]:00000000 >>>>>>> [ 2.234928] [0x0c]:00000000 >>>>>>> [ 2.235103] [0x10]:00000000 >>>>>>> [ 2.235278] [0x14]:00003000 >>>>>>> [ 2.235453] [0x18]:00000078 >>>>>>> [ 2.235629] mpt2sas_cm0: _base_allocate_memory_pools >>>>>>> [ 2.235826] mpt2sas_cm0: scatter gather: sge_in_main_msg(3), sge_per_chain(15), sge_per_io(128), chains_per_io(9) >>>>>>> [ 2.236227] mpt2sas_cm0: reply post free pool (0xffff8800bb380000): depth(6944),element_size(8), pool_size(54 kB) >>>>>>> [ 2.236611] mpt2sas_cm0: reply_post_free_dma = (0xbb380000) >>>>>>> [ 2.236813] mpt2sas_cm0: scsi host: can_queue depth (3307) >>>>>>> [ 2.237086] mpt2sas_cm0: request pool(0xffff8800ba880000): depth(3432), frame_size(128), pool_size(429 kB) >>>>>>> [ 2.238580] mpt2sas_cm0: request pool: dma(0xba880000) >>>>>>> [ 2.238781] mpt2sas_cm0: scsiio(0xffff8800ba880000): depth(3307) >>>>>>> [ 2.243644] mpt2sas_cm0: chain pool depth(29763), frame_size(128), pool_size(3720 kB) >>>>>>> [ 2.243887] mpt2sas_cm0: hi_priority(0xffff8800ba8e7600): depth(60), start smid(3308) >>>>>>> [ 2.244113] mpt2sas_cm0: internal(0xffff8800ba8e9400): depth(65), start smid(3368) >>>>>>> [ 2.244390] mpt2sas_cm0: sense pool(0xffff8800ba480000): depth(3307), element_size(96), pool_size(310 kB) >>>>>>> [ 2.244774] mpt2sas_cm0: sense_dma(0xba480000) >>>>>>> [ 2.245038] mpt2sas_cm0: reply pool(0xffff8800ba500000): depth(3496), frame_size(128), pool_size(437 kB) >>>>>>> [ 2.245413] mpt2sas_cm0: reply_dma(0xba500000) >>>>>>> [ 2.245608] mpt2sas_cm0: reply_free pool(0xffff8800ba430000): depth(3496), element_size(4), pool_size(13 kB) >>>>>>> [ 2.245985] mpt2sas_cm0: reply_free_dma (0xba430000) >>>>>>> [ 2.246181] mpt2sas_cm0: config page(0xffff8800ba429000): size(512) >>>>>>> [ 2.246389] mpt2sas_cm0: config_page_dma(0xba429000) >>>>>>> [ 2.246584] mpt2sas_cm0: Allocated physical memory: size(4964 kB) >>>>>>> [ 2.246791] mpt2sas_cm0: Current Controller Queue Depth(3307),Max Controller Queue Depth(3432) >>>>>>> [ 2.247155] mpt2sas_cm0: Scatter Gather Elements per IO(128) >>>>>>> [ 2.247361] mpt2sas_cm0: _base_make_ioc_operational >>>>>>> [ 2.247962] mpt2sas_cm0: _base_send_ioc_init >>>>>>> [ 2.248154] offset:data >>>>>>> [ 2.248325] [0x00]:02000004 >>>>>>> [ 2.248499] [0x04]:00000000 >>>>>>> [ 2.248673] [0x08]:00000000 >>>>>>> [ 2.248848] [0x0c]:23000200 >>>>>>> [ 2.249023] [0x10]:00000000 >>>>>>> [ 2.249197] [0x14]:00000000 >>>>>>> [ 2.249372] [0x18]:00200000 >>>>>>> [ 2.249546] [0x1c]:0da81b20 >>>>>>> [ 2.249720] [0x20]:00000000 >>>>>>> [ 2.249894] [0x24]:00000000 >>>>>>> [ 2.250068] [0x28]:ba880000 >>>>>>> [ 2.250242] [0x2c]:00000000 >>>>>>> [ 2.250416] [0x30]:bb380000 >>>>>>> [ 2.250589] [0x34]:00000000 >>>>>>> [ 2.250768] [0x38]:ba430000 >>>>>>> [ 2.250941] [0x3c]:00000000 >>>>>>> [ 2.251115] [0x40]:983eb686 >>>>>>> [ 2.251288] [0x44]:00000153 >>>>>>> [ 2.296610] offset:data >>>>>>> [ 2.296795] [0x00]:02050004 >>>>>>> [ 2.296969] [0x04]:00000000 >>>>>>> [ 2.297143] [0x08]:00000000 >>>>>>> [ 2.297318] [0x0c]:00000000 >>>>>>> [ 2.297493] [0x10]:00000000 >>>>>>> [ 2.297668] mpt2sas_cm0: _base_event_notification >>>>>>> [ 5.093707] floppy0: no floppy controllers found >>>>>>> [ 32.293619] mpt2sas_cm0: _base_event_notification: timeout >>>>>>> [ 32.293909] mf: >>>>>>> >>>>>>> [ 32.294132] 07000000 >>>>>>> [ 32.294397] 00000000 >>>>>>> [ 32.294445] 00000000 >>>>>>> [ 32.294719] 00000000 >>>>>>> [ 32.294767] 00000000 >>>>>>> [ 32.295031] 0f2f7fff >>>>>>> [ 32.295078] ffffff7c >>>>>>> [ 32.295342] ffffffff >>>>>>> [ 32.295389] >>>>>>> >>>>>>> [ 32.295823] ffffffff >>>>>>> [ 32.295871] 00000000 >>>>>>> [ 32.296134] 00000000 >>>>>>> >>>>>>> [ 32.296615] mpt2sas_cm0: mpt3sas_base_free_resources >>>>>>> [ 32.296880] mpt2sas_cm0: _base_make_ioc_ready >>>>>>> [ 32.297135] mpt2sas_cm0: sending message unit reset !! >>>>>>> [ 32.298941] mpt2sas_cm0: message unit reset: SUCCESS >>>>>>> [ 32.299212] mpt2sas_cm0: mpt3sas_base_unmap_resources >>>>>>> [ 32.300381] mpt2sas_cm0: _base_release_memory_pools >>>>>>> [ 32.300654] mpt2sas_cm0: request_pool(0xffff8800ba880000): free >>>>>>> [ 32.300934] mpt2sas_cm0: sense_pool(0xffff8800ba480000): free >>>>>>> [ 32.301211] mpt2sas_cm0: reply_pool(0xffff8800ba500000): free >>>>>>> [ 32.301485] mpt2sas_cm0: reply_free_pool(0xffff8800ba430000): free >>>>>>> [ 32.301774] mpt2sas_cm0: reply_post_free_pool(0xffff8800bb380000): free >>>>>>> [ 32.302061] mpt2sas_cm0: config_page(0xffff8800ba429000): free >>>>>>> [ 32.371097] mpt2sas_cm0: failure at drivers/scsi/mpt3sas/mpt3sas_scsih.c:8592/_scsih_probe()! >>>>>>> [ 32.371958] mpt2sas_cm1: mpt3sas_base_attach >>>>>>> [ 32.372154] mpt2sas_cm1: mpt3sas_base_map_resources >>>>>>> [ 32.372950] mpt2sas_cm1: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3074748 kB) >>>>>>> [ 32.373201] mpt2sas_cm1: _base_get_ioc_facts >>>>>>> [ 32.375261] mpt2sas_cm1: _base_wait_for_iocstate >>>>>>> [ 32.432012] offset:data >>>>>>> [ 32.432262] [0x00]:03100200 >>>>>>> [ 32.432499] [0x04]:00002300 >>>>>>> [ 32.432735] [0x08]:00000000 >>>>>>> [ 32.432971] [0x0c]:00000000 >>>>>>> [ 32.433206] [0x10]:00000000 >>>>>>> [ 32.433443] [0x14]:00010480 >>>>>>> [ 32.433701] [0x18]:22130d68 >>>>>>> [ 32.433937] [0x1c]:0001285c >>>>>>> [ 32.435434] [0x20]:14000400 >>>>>>> [ 32.435674] [0x24]:00000020 >>>>>>> [ 32.435909] [0x28]:0100000f >>>>>>> [ 32.436144] [0x2c]:000c000b >>>>>>> [ 32.436379] [0x30]:003c0003 >>>>>>> [ 32.436615] [0x34]:0020ffe0 >>>>>>> [ 32.436850] [0x38]:00800122 >>>>>>> [ 32.437085] [0x3c]:00000009 >>>>>>> [ 32.437322] mpt2sas_cm1: hba queue depth(3432), max chains per io(128) >>>>>>> [ 32.437607] mpt2sas_cm1: request frame size(128), reply frame size(128) >>>>>>> [ 32.438014] mpt2sas_cm1: msix is supported, vector_count(1) >>>>>>> [ 32.438288] mpt2sas_cm1: MSI-X vectors supported: 1, no of cores: 4, max_msix_vectors: 8 >>>>>>> [ 32.439101] mpt2sas1-msix0: PCI-MSI-X enabled: IRQ 58 >>>>>>> [ 32.439373] mpt2sas_cm1: iomem(0x00000000fd1fc000), mapped(0xffffc900000d8000), size(16384) >>>>>>> [ 32.439682] mpt2sas_cm1: ioport(0x0000000000007000), size(256) >>>>>>> [ 32.440504] mpt2sas_cm1: _base_get_ioc_facts >>>>>>> [ 32.440765] mpt2sas_cm1: _base_wait_for_iocstate >>>>>>> [ 32.499305] offset:data >>>>>>> [ 32.499557] [0x00]:03100200 >>>>>>> [ 32.499794] [0x04]:00002300 >>>>>>> [ 32.500031] [0x08]:00000000 >>>>>>> [ 32.500267] [0x0c]:00000000 >>>>>>> [ 32.500504] [0x10]:00000000 >>>>>>> [ 32.500740] [0x14]:00010480 >>>>>>> [ 32.500974] [0x18]:22130d68 >>>>>>> [ 32.501209] [0x1c]:0001285c >>>>>>> [ 32.501444] [0x20]:14000400 >>>>>>> [ 32.501687] [0x24]:00000020 >>>>>>> [ 32.501922] [0x28]:0100000f >>>>>>> [ 32.502157] [0x2c]:000c000b >>>>>>> [ 32.502391] [0x30]:003c0003 >>>>>>> [ 32.502626] [0x34]:0020ffe0 >>>>>>> [ 32.502862] [0x38]:00800122 >>>>>>> [ 32.503098] [0x3c]:00000009 >>>>>>> [ 32.503336] mpt2sas_cm1: hba queue depth(3432), max chains per io(128) >>>>>>> [ 32.503644] mpt2sas_cm1: request frame size(128), reply frame size(128) >>>>>>> [ 32.503933] mpt2sas_cm1: _base_make_ioc_ready >>>>>>> [ 32.504191] mpt2sas_cm1: _base_get_port_facts >>>>>>> [ 32.534282] offset:data >>>>>>> [ 32.534537] [0x00]:05070000 >>>>>>> [ 32.534782] [0x04]:00000000 >>>>>>> [ 32.535058] [0x08]:00000000 >>>>>>> [ 32.536473] [0x0c]:00000000 >>>>>>> [ 32.536710] [0x10]:00000000 >>>>>>> [ 32.536946] [0x14]:00003000 >>>>>>> [ 32.537183] [0x18]:00000078 >>>>>>> [ 32.537420] mpt2sas_cm1: _base_allocate_memory_pools >>>>>>> [ 32.537686] mpt2sas_cm1: scatter gather: sge_in_main_msg(3), sge_per_chain(15), sge_per_io(128), chains_per_io(9) >>>>>>> [ 32.538232] mpt2sas_cm1: reply post free pool (0xffff8800bb3d0000): depth(6944),element_size(8), pool_size(54 kB) >>>>>>> [ 32.538758] mpt2sas_cm1: reply_post_free_dma = (0xbb3d0000) >>>>>>> [ 32.539030] mpt2sas_cm1: scsi host: can_queue depth (3307) >>>>>>> [ 32.539378] mpt2sas_cm1: request pool(0xffff8800ba480000): depth(3432), frame_size(128), pool_size(429 kB) >>>>>>> [ 32.539882] mpt2sas_cm1: request pool: dma(0xba480000) >>>>>>> [ 32.540149] mpt2sas_cm1: scsiio(0xffff8800ba480000): depth(3307) >>>>>>> [ 32.545893] mpt2sas_cm1: chain pool depth(29763), frame_size(128), pool_size(3720 kB) >>>>>>> [ 32.546137] mpt2sas_cm1: hi_priority(0xffff8800ba4e7600): depth(60), start smid(3308) >>>>>>> [ 32.546365] mpt2sas_cm1: internal(0xffff8800ba4e9400): depth(65), start smid(3368) >>>>>>> [ 32.546651] mpt2sas_cm1: sense pool(0xffff8800ba880000): depth(3307), element_size(96), pool_size(310 kB) >>>>>>> [ 32.547030] mpt2sas_cm1: sense_dma(0xba880000) >>>>>>> [ 32.547537] mpt2sas_cm1: reply pool(0xffff880000100000): depth(3496), frame_size(128), pool_size(437 kB) >>>>>>> [ 32.547921] mpt2sas_cm1: reply_dma(0x100000) >>>>>>> [ 32.548117] mpt2sas_cm1: reply_free pool(0xffff8800ba964000): depth(3496), element_size(4), pool_size(13 kB) >>>>>>> [ 32.548500] mpt2sas_cm1: reply_free_dma (0xba964000) >>>>>>> [ 32.548698] mpt2sas_cm1: config page(0xffff8800ba960000): size(512) >>>>>>> [ 32.548908] mpt2sas_cm1: config_page_dma(0xba960000) >>>>>>> [ 32.549105] mpt2sas_cm1: Allocated physical memory: size(4964 kB) >>>>>>> [ 32.549314] mpt2sas_cm1: Current Controller Queue Depth(3307),Max Controller Queue Depth(3432) >>>>>>> [ 32.550950] mpt2sas_cm1: Scatter Gather Elements per IO(128) >>>>>>> [ 32.551160] mpt2sas_cm1: _base_make_ioc_operational >>>>>>> [ 32.551855] mpt2sas_cm1: _base_send_ioc_init >>>>>>> [ 32.552051] offset:data >>>>>>> [ 32.552224] [0x00]:02000004 >>>>>>> [ 32.552400] [0x04]:00000000 >>>>>>> [ 32.552576] [0x08]:00000000 >>>>>>> [ 32.552761] [0x0c]:23000200 >>>>>>> [ 32.552937] [0x10]:00000000 >>>>>>> [ 32.553114] [0x14]:00000000 >>>>>>> [ 32.553291] [0x18]:00200000 >>>>>>> [ 32.553468] [0x1c]:0da81b20 >>>>>>> [ 32.553685] [0x20]:00000000 >>>>>>> [ 32.553862] [0x24]:00000000 >>>>>>> [ 32.554038] [0x28]:ba480000 >>>>>>> [ 32.554215] [0x2c]:00000000 >>>>>>> [ 32.554393] [0x30]:bb3d0000 >>>>>>> [ 32.554569] [0x34]:00000000 >>>>>>> [ 32.554752] [0x38]:ba964000 >>>>>>> [ 32.554929] [0x3c]:00000000 >>>>>>> [ 32.555106] [0x40]:983f2ce6 >>>>>>> [ 32.555283] [0x44]:00000153 >>>>>>> [ 32.601516] offset:data >>>>>>> [ 32.601768] [0x00]:02050004 >>>>>>> [ 32.602003] [0x04]:00000000 >>>>>>> [ 32.602239] [0x08]:00000000 >>>>>>> [ 32.602474] [0x0c]:00000000 >>>>>>> [ 32.602709] [0x10]:00000000 >>>>>>> [ 32.602945] mpt2sas_cm1: _base_event_notification >>>>>>> [ 62.593604] mpt2sas_cm1: _base_event_notification: timeout >>>>>>> [ 62.593906] mf: >>>>>>> >>>>>>> [ 62.594127] 07000000 >>>>>>> [ 62.594390] 00000000 >>>>>>> [ 62.594438] 00000000 >>>>>>> [ 62.594709] 00000000 >>>>>>> [ 62.594757] 00000000 >>>>>>> [ 62.595019] 0f2f7fff >>>>>>> [ 62.595067] ffffff7c >>>>>>> [ 62.595330] ffffffff >>>>>>> [ 62.595377] >>>>>>> >>>>>>> [ 62.595808] ffffffff >>>>>>> [ 62.595855] 00000000 >>>>>>> [ 62.596117] 00000000 >>>>>>> >>>>>>> [ 62.596601] mpt2sas_cm1: mpt3sas_base_free_resources >>>>>>> [ 62.596871] mpt2sas_cm1: _base_make_ioc_ready >>>>>>> [ 62.597125] mpt2sas_cm1: sending message unit reset !! >>>>>>> [ 62.599013] mpt2sas_cm1: message unit reset: SUCCESS >>>>>>> [ 62.599283] mpt2sas_cm1: mpt3sas_base_unmap_resources >>>>>>> [ 62.600443] mpt2sas_cm1: _base_release_memory_pools >>>>>>> [ 62.600721] mpt2sas_cm1: request_pool(0xffff8800ba480000): free >>>>>>> [ 62.601002] mpt2sas_cm1: sense_pool(0xffff8800ba880000): free >>>>>>> [ 62.601280] mpt2sas_cm1: reply_pool(0xffff880000100000): free >>>>>>> [ 62.601560] mpt2sas_cm1: reply_free_pool(0xffff8800ba964000): free >>>>>>> [ 62.601845] mpt2sas_cm1: reply_post_free_pool(0xffff8800bb3d0000): free >>>>>>> [ 62.602133] mpt2sas_cm1: config_page(0xffff8800ba960000): free >>>>>>> [ 62.673591] mpt2sas_cm1: failure at drivers/scsi/mpt3sas/mpt3sas_scsih.c:8592/_scsih_probe()! >>>>>> >>>>>> These are for two controllers, I don't know whether the output from the >>>>>> second is helpful at all - I added it anyway. >>>>>> >>>>>> >>>>>> I managed to boot the same 4.5.0 kernel successfully after warm >>>>>> rebooting from 4.1.20. That gave me this dmesg output (for comparison): >>>>>> >>>>>>> [ 2.057685] mpt3sas version 09.102.00.00 loaded >>>>>>> [ 2.058371] mpt2sas_cm0: mpt3sas_base_attach >>>>>>> [ 2.058632] mpt2sas_cm0: mpt3sas_base_map_resources >>>>>>> [ 2.059583] mpt2sas_cm0: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3074748 kB) >>>>>>> [ 2.059911] mpt2sas_cm0: _base_get_ioc_facts >>>>>>> [ 2.060166] mpt2sas_cm0: _base_wait_for_iocstate >>>>>>> [ 2.116337] offset:data >>>>>>> [ 2.116576] [0x00]:03100200 >>>>>>> [ 2.116817] [0x04]:00002300 >>>>>>> [ 2.117051] [0x08]:00000000 >>>>>>> [ 2.117285] [0x0c]:00000000 >>>>>>> [ 2.117518] [0x10]:00000000 >>>>>>> [ 2.117752] [0x14]:00010480 >>>>>>> [ 2.117986] [0x18]:22130d68 >>>>>>> [ 2.118220] [0x1c]:0001285c >>>>>>> [ 2.119624] [0x20]:14000400 >>>>>>> [ 2.119858] [0x24]:00000020 >>>>>>> [ 2.120093] [0x28]:0100000f >>>>>>> [ 2.120351] [0x2c]:000c000b >>>>>>> [ 2.120586] [0x30]:003c0003 >>>>>>> [ 2.120820] [0x34]:0020ffe0 >>>>>>> [ 2.121055] [0x38]:00800122 >>>>>>> [ 2.121288] [0x3c]:00000009 >>>>>>> [ 2.121524] mpt2sas_cm0: hba queue depth(3432), max chains per io(128) >>>>>>> [ 2.121808] mpt2sas_cm0: request frame size(128), reply frame size(128) >>>>>>> [ 2.122195] mpt2sas_cm0: msix is supported, vector_count(1) >>>>>>> [ 2.122468] mpt2sas_cm0: MSI-X vectors supported: 1, no of cores: 4, max_msix_vectors: -1 >>>>>>> [ 2.123239] mpt2sas0-msix0: PCI-MSI-X enabled: IRQ 58 >>>>>>> [ 2.123507] mpt2sas_cm0: iomem(0x00000000fd4fc000), mapped(0xffffc900000d0000), size(16384) >>>>>>> [ 2.123816] mpt2sas_cm0: ioport(0x0000000000004000), size(256) >>>>>>> [ 2.124623] mpt2sas_cm0: _base_get_ioc_facts >>>>>>> [ 2.124878] mpt2sas_cm0: _base_wait_for_iocstate >>>>>>> [ 2.180907] offset:data >>>>>>> [ 2.181145] [0x00]:03100200 >>>>>>> [ 2.181379] [0x04]:00002300 >>>>>>> [ 2.181613] [0x08]:00000000 >>>>>>> [ 2.181847] [0x0c]:00000000 >>>>>>> [ 2.182081] [0x10]:00000000 >>>>>>> [ 2.182315] [0x14]:00010480 >>>>>>> [ 2.182547] [0x18]:22130d68 >>>>>>> [ 2.182781] [0x1c]:0001285c >>>>>>> [ 2.183014] [0x20]:14000400 >>>>>>> [ 2.183248] [0x24]:00000020 >>>>>>> [ 2.183481] [0x28]:0100000f >>>>>>> [ 2.183720] [0x2c]:000c000b >>>>>>> [ 2.183954] [0x30]:003c0003 >>>>>>> [ 2.184190] [0x34]:0020ffe0 >>>>>>> [ 2.184424] [0x38]:00800122 >>>>>>> [ 2.184658] [0x3c]:00000009 >>>>>>> [ 2.184893] mpt2sas_cm0: hba queue depth(3432), max chains per io(128) >>>>>>> [ 2.185177] mpt2sas_cm0: request frame size(128), reply frame size(128) >>>>>>> [ 2.185462] mpt2sas_cm0: _base_make_ioc_ready >>>>>>> [ 2.185717] mpt2sas_cm0: _base_get_port_facts >>>>>>> [ 2.214057] offset:data >>>>>>> [ 2.214295] [0x00]:05070000 >>>>>>> [ 2.214529] [0x04]:00000000 >>>>>>> [ 2.214762] [0x08]:00000000 >>>>>>> [ 2.214997] [0x0c]:00000000 >>>>>>> [ 2.215230] [0x10]:00000000 >>>>>>> [ 2.215464] [0x14]:00003000 >>>>>>> [ 2.215697] [0x18]:00000078 >>>>>>> [ 2.215931] mpt2sas_cm0: _base_allocate_memory_pools >>>>>>> [ 2.216194] mpt2sas_cm0: scatter gather: sge_in_main_msg(3), sge_per_chain(15), sge_per_io(128), chains_per_io(9) >>>>>>> [ 2.216734] mpt2sas_cm0: reply post free pool (0xffff8800bafc0000): depth(6944),element_size(8), pool_size(54 kB) >>>>>>> [ 2.217244] mpt2sas_cm0: reply_post_free_dma = (0xbafc0000) >>>>>>> [ 2.217514] mpt2sas_cm0: scsi host: can_queue depth (3307) >>>>>>> [ 2.217866] mpt2sas_cm0: request pool(0xffff8800ba800000): depth(3432), frame_size(128), pool_size(429 kB) >>>>>>> [ 2.218369] mpt2sas_cm0: request pool: dma(0xba800000) >>>>>>> [ 2.218637] mpt2sas_cm0: scsiio(0xffff8800ba800000): depth(3307) >>>>>>> [ 2.224773] mpt2sas_cm0: chain pool depth(29763), frame_size(128), pool_size(3720 kB) >>>>>>> [ 2.225092] mpt2sas_cm0: hi_priority(0xffff8800ba867600): depth(60), start smid(3308) >>>>>>> [ 2.225395] mpt2sas_cm0: internal(0xffff8800ba869400): depth(65), start smid(3368) >>>>>>> [ 2.225958] mpt2sas_cm0: sense pool(0xffff8800ba480000): depth(3307), element_size(96), pool_size(310 kB) >>>>>>> [ 2.226457] mpt2sas_cm0: sense_dma(0xba480000) >>>>>>> [ 2.227039] mpt2sas_cm0: reply pool(0xffff8800ba500000): depth(3496), frame_size(128), pool_size(437 kB) >>>>>>> [ 2.227413] mpt2sas_cm0: reply_dma(0xba500000) >>>>>>> [ 2.227616] mpt2sas_cm0: reply_free pool(0xffff8800ba450000): depth(3496), element_size(4), pool_size(13 kB) >>>>>>> [ 2.227992] mpt2sas_cm0: reply_free_dma (0xba450000) >>>>>>> [ 2.228192] mpt2sas_cm0: config page(0xffff8800ba43b000): size(512) >>>>>>> [ 2.228402] mpt2sas_cm0: config_page_dma(0xba43b000) >>>>>>> [ 2.228598] mpt2sas_cm0: Allocated physical memory: size(4964 kB) >>>>>>> [ 2.228806] mpt2sas_cm0: Current Controller Queue Depth(3307),Max Controller Queue Depth(3432) >>>>>>> [ 2.229171] mpt2sas_cm0: Scatter Gather Elements per IO(128) >>>>>>> [ 2.229378] mpt2sas_cm0: _base_make_ioc_operational >>>>>>> [ 2.229959] mpt2sas_cm0: _base_send_ioc_init >>>>>>> [ 2.230151] offset:data >>>>>>> [ 2.230323] [0x00]:02000004 >>>>>>> [ 2.230499] [0x04]:00000000 >>>>>>> [ 2.230675] [0x08]:00000000 >>>>>>> [ 2.230851] [0x0c]:23000200 >>>>>>> [ 2.231026] [0x10]:00000000 >>>>>>> [ 2.231201] [0x14]:00000000 >>>>>>> [ 2.231376] [0x18]:00200000 >>>>>>> [ 2.231551] [0x1c]:0da81b20 >>>>>>> [ 2.231726] [0x20]:00000000 >>>>>>> [ 2.231900] [0x24]:00000000 >>>>>>> [ 2.232075] [0x28]:ba800000 >>>>>>> [ 2.232250] [0x2c]:00000000 >>>>>>> [ 2.232423] [0x30]:bafc0000 >>>>>>> [ 2.232597] [0x34]:00000000 >>>>>>> [ 2.232775] [0x38]:ba450000 >>>>>>> [ 2.232950] [0x3c]:00000000 >>>>>>> [ 2.233125] [0x40]:98596e4f >>>>>>> [ 2.233299] [0x44]:00000153 >>>>>>> [ 2.278752] offset:data >>>>>>> [ 2.278988] [0x00]:02050004 >>>>>>> [ 2.279220] [0x04]:00000000 >>>>>>> [ 2.279453] [0x08]:00000000 >>>>>>> [ 2.279685] [0x0c]:00000000 >>>>>>> [ 2.279918] [0x10]:00000000 >>>>>>> [ 2.280151] mpt2sas_cm0: _base_event_notification >>>>>>> [ 2.280537] mpt2sas_cm0: _base_event_notification: complete >>>>>>> [ 2.281694] mpt2sas_cm0: LSISAS2008: FWVersion(20.00.04.00), ChipRevision(0x03), BiosVersion(07.39.00.00) >>>>>>> [ 2.282196] mpt2sas_cm0: Protocol=( >>>>>>> [ 2.282261] Initiator >>>>>>> [ 2.282522] ,Target >>>>>>> [ 2.282567] ), >>>>>>> [ 2.282824] Capabilities=( >>>>>>> [ 2.282877] TLR >>>>>>> [ 2.283132] ,EEDP >>>>>>> [ 2.283175] ,Snapshot Buffer >>>>>>> [ 2.283444] ,Diag Trace Buffer >>>>>>> [ 2.283502] ,Task Set Full >>>>>>> [ 2.283774] ,NCQ >>>>>>> [ 2.283816] ) >>>>>>> [ 2.284350] scsi host0: Fusion MPT SAS Host >>>>>>> [ 2.299028] mpt2sas_cm0: sending port enable !! >>>>>>> [ 2.299540] mpt2sas_cm0: Discovery: (start) >>>>>>> >>>>>>> [ 2.299972] mpt2sas_cm0: SAS Enclosure Device Status Change >>>>>>> [ 2.299984] mpt2sas_cm0: discovery event: (start) >>>>>>> >>>>>>> [ 2.300554] mpt2sas_cm0: SAS Topology Change List >>>>>>> [ 2.300759] mpt2sas_cm0: Discovery: (stop) >>>>>>> >>>>>>> [ 2.301146] mpt2sas_cm0: Discovery: (start) >>>>>>> >>>>>>> [ 2.301535] mpt2sas_cm0: Discovery: (stop) >>>>>>> >>>>>>> [ 2.301927] mpt2sas_cm0: Discovery: (start) >>>>>>> >>>>>>> [ 2.302316] mpt2sas_cm0: Discovery: (stop) >>>>>>> >>>>>>> [ 2.302707] mpt2sas_cm0: Discovery: (start) >>>>>>> >>>>>>> [ 2.304908] mpt2sas_cm0: Discovery: (stop) >>>>>>> >>>>>>> [ 2.305297] mpt2sas_cm0: Discovery: (start) >>>>>>> >>>>>>> [ 2.306776] mpt2sas_cm0: Discovery: (stop) >>>>>>> >>>>>>> [ 2.307166] mpt2sas_cm0: Discovery: (start) >>>>>>> >>>>>>> [ 2.307559] mpt2sas_cm0: Discovery: (stop) >>>>>>> >>>>>>> [ 2.307948] mpt2sas_cm0: Discovery: (start) >>>>>>> >>>>>>> [ 2.308336] mpt2sas_cm0: Discovery: (stop) >>>>>>> >>>>>>> [ 2.311738] mpt2sas_cm0: host_add: handle(0x0001), sas_addr(0x500605b003683dd0), phys(8) >>>>>>> [ 2.312097] mpt2sas_cm0: enclosure status change: (enclosure add) >>>>>>> handle(0x0001), enclosure logical id(0x500605b003683dd0) number slots(0) >>>>>>> [ 2.312551] mpt2sas_cm0: sas topology change: (responding) >>>>>>> [ 2.312768] handle(0x0000), enclosure_handle(0x0001) start_phy(00), count(8) >>>>>>> [ 2.313003] phy(01), attached_handle(0x0009): target add: link rate: new(0x0a), old(0x00) >>>>>>> [ 2.313250] phy(02), attached_handle(0x000a): target add: link rate: new(0x09), old(0x00) >>>>>>> [ 2.313498] phy(03), attached_handle(0x000b): target add: link rate: new(0x09), old(0x00) >>>>>>> [ 2.313745] phy(04), attached_handle(0x000c): target add: link rate: new(0x09), old(0x00) >>>>>>> [ 2.313992] phy(05), attached_handle(0x000d): target add: link rate: new(0x09), old(0x00) >>>>>>> [ 2.314248] phy(06), attached_handle(0x000e): target add: link rate: new(0x09), old(0x00) >>>>>>> [ 2.314495] phy(07), attached_handle(0x000f): target add: link rate: new(0x09), old(0x00) >>>>>>> [ 2.314747] mpt2sas_cm0: updating handles for sas_host(0x500605b003683dd0) >>>>>>> [ 2.316041] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x0009), sas_addr(0x4433221101000000) >>>>>>> [ 2.316465] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 2) >>>>>>> [ 2.317200] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000a), sas_addr(0x4433221102000000) >>>>>>> [ 2.317669] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 1) >>>>>>> [ 2.318431] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000b), sas_addr(0x4433221103000000) >>>>>>> [ 2.318900] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 0) >>>>>>> [ 2.319366] mpt2sas_cm0: _scsih_determine_boot_device: current_boot_device(0x4433221103000000) >>>>>>> [ 2.320151] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000c), sas_addr(0x4433221104000000) >>>>>>> [ 2.321371] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 7) >>>>>>> [ 2.322137] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000d), sas_addr(0x4433221105000000) >>>>>>> [ 2.322606] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 6) >>>>>>> [ 2.323367] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000e), sas_addr(0x4433221106000000) >>>>>>> [ 2.323834] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 5) >>>>>>> [ 2.324602] mpt2sas_cm0: _scsih_sas_device_init_add: handle(0x000f), sas_addr(0x4433221107000000) >>>>>>> [ 2.325071] mpt2sas_cm0: _scsih_sas_device_init_add: enclosure logical id(0x500605b003683dd0), slot( 4) >>>>>>> [ 2.325541] mpt2sas_cm0: discovery event: (stop) >>>>>>> >>>>>>> [ 2.326017] mpt2sas_cm0: discovery event: (start) >>>>>>> >>>>>>> [ 2.326492] mpt2sas_cm0: discovery event: (stop) >>>>>>> >>>>>>> [ 2.326975] mpt2sas_cm0: discovery event: (start) >>>>>>> >>>>>>> [ 2.327450] mpt2sas_cm0: discovery event: (stop) >>>>>>> >>>>>>> [ 2.327923] mpt2sas_cm0: discovery event: (start) >>>>>>> >>>>>>> [ 2.328396] mpt2sas_cm0: discovery event: (stop) >>>>>>> >>>>>>> [ 2.328868] mpt2sas_cm0: discovery event: (start) >>>>>>> >>>>>>> [ 2.329340] mpt2sas_cm0: discovery event: (stop) >>>>>>> >>>>>>> [ 2.329816] mpt2sas_cm0: discovery event: (start) >>>>>>> >>>>>>> [ 2.330316] mpt2sas_cm0: discovery event: (stop) >>>>>>> >>>>>>> [ 2.330797] mpt2sas_cm0: discovery event: (start) >>>>>>> >>>>>>> [ 2.331269] mpt2sas_cm0: discovery event: (stop) >>>>>>> >>>>>>> [ 2.331740] mpt2sas_cm0: port enable: complete from worker thread >>>>>>> [ 2.350236] mpt2sas_cm0: port enable: SUCCESS >>>>>>> [ 2.356432] scsi 0:0:0:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 >>>>>>> [ 2.356683] scsi 0:0:0:0: SATA: handle(0x000b), sas_addr(0x4433221103000000), phy(3), device_name(0x5000c5000267c9f8) >>>>>>> [ 2.357080] scsi 0:0:0:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(0) >>>>>>> [ 2.357405] scsi 0:0:0:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>>>> [ 2.383043] scsi 0:0:1:0: Direct-Access ATA Hitachi HDS5C302 A800 PQ: 0 ANSI: 6 >>>>>>> [ 2.383296] scsi 0:0:1:0: SATA: handle(0x0009), sas_addr(0x4433221101000000), phy(1), device_name(0x5000cca369cdd311) >>>>>>> [ 2.383684] scsi 0:0:1:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(2) >>>>>>> [ 2.384028] scsi 0:0:1:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>>>> [ 2.405088] scsi 0:0:2:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 >>>>>>> [ 2.405346] scsi 0:0:2:0: SATA: handle(0x000a), sas_addr(0x4433221102000000), phy(2), device_name(0x5000c5000ccfbd32) >>>>>>> [ 2.405735] scsi 0:0:2:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(1) >>>>>>> [ 2.406082] scsi 0:0:2:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>>>> [ 2.424125] scsi 0:0:3:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 >>>>>>> [ 2.424373] scsi 0:0:3:0: SATA: handle(0x000c), sas_addr(0x4433221104000000), phy(4), device_name(0x5000c5000267abee) >>>>>>> [ 2.424763] scsi 0:0:3:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(7) >>>>>>> [ 2.425108] scsi 0:0:3:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>>>> [ 2.444834] scsi 0:0:4:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 >>>>>>> [ 2.445086] scsi 0:0:4:0: SATA: handle(0x000d), sas_addr(0x4433221105000000), phy(5), device_name(0x5000c50009c0e5e6) >>>>>>> [ 2.445478] scsi 0:0:4:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(6) >>>>>>> [ 2.445803] scsi 0:0:4:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>>>> [ 2.464065] scsi 0:0:5:0: Direct-Access ATA ST3750330NS SN16 PQ: 0 ANSI: 6 >>>>>>> [ 2.464312] scsi 0:0:5:0: SATA: handle(0x000e), sas_addr(0x4433221106000000), phy(6), device_name(0x5000c5003cb9ac10) >>>>>>> [ 2.464699] scsi 0:0:5:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(5) >>>>>>> [ 2.465048] scsi 0:0:5:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>>>> [ 2.484016] scsi 0:0:6:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 >>>>>>> [ 2.484266] scsi 0:0:6:0: SATA: handle(0x000f), sas_addr(0x4433221107000000), phy(7), device_name(0x5000c5000839b69e) >>>>>>> [ 2.484655] scsi 0:0:6:0: SATA: enclosure_logical_id(0x500605b003683dd0), slot(4) >>>>>>> [ 2.485001] scsi 0:0:6:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>>>> [ 2.500660] mpt2sas_cm1: mpt3sas_base_attach >>>>>>> [ 2.500861] mpt2sas_cm1: mpt3sas_base_map_resources >>>>>>> [ 2.501599] mpt2sas_cm1: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3074748 kB) >>>>>>> [ 2.501847] mpt2sas_cm1: _base_get_ioc_facts >>>>>>> [ 2.502036] mpt2sas_cm1: _base_wait_for_iocstate >>>>>>> [ 2.559080] offset:data >>>>>>> [ 2.559318] [0x00]:03100200 >>>>>>> [ 2.559552] [0x04]:00002300 >>>>>>> [ 2.559785] [0x08]:00000000 >>>>>>> [ 2.560020] [0x0c]:00000000 >>>>>>> [ 2.560277] [0x10]:00000000 >>>>>>> [ 2.560511] [0x14]:00010480 >>>>>>> [ 2.560745] [0x18]:22130d68 >>>>>>> [ 2.560978] [0x1c]:0001285c >>>>>>> [ 2.561210] [0x20]:14000400 >>>>>>> [ 2.561443] [0x24]:00000020 >>>>>>> [ 2.561675] [0x28]:0100000f >>>>>>> [ 2.561907] [0x2c]:000c000b >>>>>>> [ 2.562139] [0x30]:003c0003 >>>>>>> [ 2.562371] [0x34]:0020ffe0 >>>>>>> [ 2.562602] [0x38]:00800122 >>>>>>> [ 2.562839] [0x3c]:00000009 >>>>>>> [ 2.563073] mpt2sas_cm1: hba queue depth(3432), max chains per io(128) >>>>>>> [ 2.563355] mpt2sas_cm1: request frame size(128), reply frame size(128) >>>>>>> [ 2.563745] mpt2sas_cm1: msix is supported, vector_count(1) >>>>>>> [ 2.564016] mpt2sas_cm1: MSI-X vectors supported: 1, no of cores: 4, max_msix_vectors: 8 >>>>>>> [ 2.564918] mpt2sas1-msix0: PCI-MSI-X enabled: IRQ 59 >>>>>>> [ 2.566189] mpt2sas_cm1: iomem(0x00000000fd1fc000), mapped(0xffffc900000d8000), size(16384) >>>>>>> [ 2.566498] mpt2sas_cm1: ioport(0x0000000000007000), size(256) >>>>>>> [ 2.567328] mpt2sas_cm1: _base_get_ioc_facts >>>>>>> [ 2.567583] mpt2sas_cm1: _base_wait_for_iocstate >>>>>>> [ 2.625125] offset:data >>>>>>> [ 2.625364] [0x00]:03100200 >>>>>>> [ 2.625597] [0x04]:00002300 >>>>>>> [ 2.625830] [0x08]:00000000 >>>>>>> [ 2.626064] [0x0c]:00000000 >>>>>>> [ 2.626296] [0x10]:00000000 >>>>>>> [ 2.626529] [0x14]:00010480 >>>>>>> [ 2.626769] [0x18]:22130d68 >>>>>>> [ 2.627002] [0x1c]:0001285c >>>>>>> [ 2.627235] [0x20]:14000400 >>>>>>> [ 2.627467] [0x24]:00000020 >>>>>>> [ 2.627702] [0x28]:0100000f >>>>>>> [ 2.627936] [0x2c]:000c000b >>>>>>> [ 2.628170] [0x30]:003c0003 >>>>>>> [ 2.628403] [0x34]:0020ffe0 >>>>>>> [ 2.628638] [0x38]:00800122 >>>>>>> [ 2.628872] [0x3c]:00000009 >>>>>>> [ 2.629107] mpt2sas_cm1: hba queue depth(3432), max chains per io(128) >>>>>>> [ 2.629388] mpt2sas_cm1: request frame size(128), reply frame size(128) >>>>>>> [ 2.629671] mpt2sas_cm1: _base_make_ioc_ready >>>>>>> [ 2.629928] mpt2sas_cm1: _base_get_port_facts >>>>>>> [ 2.660127] offset:data >>>>>>> [ 2.660389] [0x00]:05070000 >>>>>>> [ 2.660623] [0x04]:00000000 >>>>>>> [ 2.660858] [0x08]:00000000 >>>>>>> [ 2.661093] [0x0c]:00000000 >>>>>>> [ 2.661326] [0x10]:00000000 >>>>>>> [ 2.661562] [0x14]:00003000 >>>>>>> [ 2.661796] [0x18]:00000078 >>>>>>> [ 2.664346] mpt2sas_cm1: _base_allocate_memory_pools >>>>>>> [ 2.664608] mpt2sas_cm1: scatter gather: sge_in_main_msg(3), sge_per_chain(15), sge_per_io(128), chains_per_io(9) >>>>>>> [ 2.665142] mpt2sas_cm1: reply post free pool (0xffff8800b8b10000): depth(6944),element_size(8), pool_size(54 kB) >>>>>>> [ 2.666671] mpt2sas_cm1: reply_post_free_dma = (0xb8b10000) >>>>>>> [ 2.666954] mpt2sas_cm1: scsi host: can_queue depth (3307) >>>>>>> [ 2.667311] mpt2sas_cm1: request pool(0xffff8800b8b80000): depth(3432), frame_size(128), pool_size(429 kB) >>>>>>> [ 2.667813] mpt2sas_cm1: request pool: dma(0xb8b80000) >>>>>>> [ 2.668080] mpt2sas_cm1: scsiio(0xffff8800b8b80000): depth(3307) >>>>>>> [ 2.674131] mpt2sas_cm1: chain pool depth(29763), frame_size(128), pool_size(3720 kB) >>>>>>> [ 2.674448] mpt2sas_cm1: hi_priority(0xffff8800b8be7600): depth(60), start smid(3308) >>>>>>> [ 2.674750] mpt2sas_cm1: internal(0xffff8800b8be9400): depth(65), start smid(3368) >>>>>>> [ 2.675105] mpt2sas_cm1: sense pool(0xffff8800b8100000): depth(3307), element_size(96), pool_size(310 kB) >>>>>>> [ 2.675605] mpt2sas_cm1: sense_dma(0xb8100000) >>>>>>> [ 2.675944] mpt2sas_cm1: reply pool(0xffff8800b8180000): depth(3496), frame_size(128), pool_size(437 kB) >>>>>>> [ 2.676443] mpt2sas_cm1: reply_dma(0xb8180000) >>>>>>> [ 2.676702] mpt2sas_cm1: reply_free pool(0xffff8800b80a0000): depth(3496), element_size(4), pool_size(13 kB) >>>>>>> [ 2.677124] mpt2sas_cm1: reply_free_dma (0xb80a0000) >>>>>>> [ 2.677322] mpt2sas_cm1: config page(0xffff8800b807f000): size(512) >>>>>>> [ 2.677532] mpt2sas_cm1: config_page_dma(0xb807f000) >>>>>>> [ 2.677728] mpt2sas_cm1: Allocated physical memory: size(4964 kB) >>>>>>> [ 2.677936] mpt2sas_cm1: Current Controller Queue Depth(3307),Max Controller Queue Depth(3432) >>>>>>> [ 2.678304] mpt2sas_cm1: Scatter Gather Elements per IO(128) >>>>>>> [ 2.678514] mpt2sas_cm1: _base_make_ioc_operational >>>>>>> [ 2.679081] mpt2sas_cm1: _base_send_ioc_init >>>>>>> [ 2.679275] offset:data >>>>>>> [ 2.679448] [0x00]:02000004 >>>>>>> [ 2.679625] [0x04]:00000000 >>>>>>> [ 2.679805] [0x08]:00000000 >>>>>>> [ 2.681200] [0x0c]:23000200 >>>>>>> [ 2.681377] [0x10]:00000000 >>>>>>> [ 2.681554] [0x14]:00000000 >>>>>>> [ 2.681729] [0x18]:00200000 >>>>>>> [ 2.681906] [0x1c]:0da81b20 >>>>>>> [ 2.682082] [0x20]:00000000 >>>>>>> [ 2.682259] [0x24]:00000000 >>>>>>> [ 2.682435] [0x28]:b8b80000 >>>>>>> [ 2.682611] [0x2c]:00000000 >>>>>>> [ 2.682787] [0x30]:b8b10000 >>>>>>> [ 2.682963] [0x34]:00000000 >>>>>>> [ 2.683139] [0x38]:b80a0000 >>>>>>> [ 2.683314] [0x3c]:00000000 >>>>>>> [ 2.683489] [0x40]:98597011 >>>>>>> [ 2.683665] [0x44]:00000153 >>>>>>> [ 2.729849] offset:data >>>>>>> [ 2.730089] [0x00]:02050004 >>>>>>> [ 2.730349] [0x04]:00000000 >>>>>>> [ 2.730586] [0x08]:00000000 >>>>>>> [ 2.730822] [0x0c]:00000000 >>>>>>> [ 2.731058] [0x10]:00000000 >>>>>>> [ 2.731295] mpt2sas_cm1: _base_event_notification >>>>>>> [ 2.731606] mpt2sas_cm1: _base_event_notification: complete >>>>>>> [ 2.732501] mpt2sas_cm1: LSISAS2008: FWVersion(20.00.04.00), ChipRevision(0x02), BiosVersion(07.39.00.00) >>>>>>> [ 2.733010] mpt2sas_cm1: Protocol=( >>>>>>> [ 2.733074] Initiator >>>>>>> [ 2.733339] ,Target >>>>>>> [ 2.733384] ), >>>>>>> [ 2.733642] Capabilities=( >>>>>>> [ 2.733696] TLR >>>>>>> [ 2.733952] ,EEDP >>>>>>> [ 2.733995] ,Snapshot Buffer >>>>>>> [ 2.734268] ,Diag Trace Buffer >>>>>>> [ 2.734326] ,Task Set Full >>>>>>> [ 2.734595] ,NCQ >>>>>>> [ 2.734637] ) >>>>>>> [ 2.735155] scsi host1: Fusion MPT SAS Host >>>>>>> [ 2.749047] mpt2sas_cm1: sending port enable !! >>>>>>> [ 2.749563] mpt2sas_cm1: Discovery: (start) >>>>>>> >>>>>>> [ 2.749989] mpt2sas_cm1: SAS Enclosure Device Status Change >>>>>>> [ 2.750001] mpt2sas_cm1: discovery event: (start) >>>>>>> >>>>>>> [ 2.750578] mpt2sas_cm1: SAS Topology Change List >>>>>>> [ 2.750788] mpt2sas_cm1: Discovery: (stop) >>>>>>> >>>>>>> [ 2.751181] mpt2sas_cm1: Discovery: (start) >>>>>>> >>>>>>> [ 2.751571] mpt2sas_cm1: Discovery: (stop) >>>>>>> >>>>>>> [ 2.752002] mpt2sas_cm1: Discovery: (start) >>>>>>> >>>>>>> [ 2.752391] mpt2sas_cm1: Discovery: (stop) >>>>>>> >>>>>>> [ 2.752779] mpt2sas_cm1: Discovery: (start) >>>>>>> >>>>>>> [ 2.754205] mpt2sas_cm1: Discovery: (stop) >>>>>>> >>>>>>> [ 2.754593] mpt2sas_cm1: Discovery: (start) >>>>>>> >>>>>>> [ 2.754983] mpt2sas_cm1: Discovery: (stop) >>>>>>> >>>>>>> [ 2.755371] mpt2sas_cm1: Discovery: (start) >>>>>>> >>>>>>> [ 2.755762] mpt2sas_cm1: Discovery: (stop) >>>>>>> >>>>>>> [ 2.759602] mpt2sas_cm1: host_add: handle(0x0001), sas_addr(0x500605b0026f79b0), phys(8) >>>>>>> [ 2.759969] mpt2sas_cm1: enclosure status change: (enclosure add) >>>>>>> handle(0x0001), enclosure logical id(0x500605b0026f79b0) number slots(0) >>>>>>> [ 2.760407] mpt2sas_cm1: sas topology change: (responding) >>>>>>> [ 2.760612] handle(0x0000), enclosure_handle(0x0001) start_phy(00), count(8) >>>>>>> [ 2.760834] phy(02), attached_handle(0x000e): target add: link rate: new(0x0a), old(0x00) >>>>>>> [ 2.761066] phy(03), attached_handle(0x000b): target add: link rate: new(0x0a), old(0x00) >>>>>>> [ 2.761304] phy(04), attached_handle(0x000d): target add: link rate: new(0x09), old(0x00) >>>>>>> [ 2.761538] phy(05), attached_handle(0x0009): target add: link rate: new(0x09), old(0x00) >>>>>>> [ 2.761771] phy(06), attached_handle(0x000a): target add: link rate: new(0x09), old(0x00) >>>>>>> [ 2.762002] phy(07), attached_handle(0x000c): target add: link rate: new(0x09), old(0x00) >>>>>>> [ 2.762235] mpt2sas_cm1: updating handles for sas_host(0x500605b0026f79b0) >>>>>>> [ 2.763653] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x000e), sas_addr(0x4433221102000000) >>>>>>> [ 2.764036] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 1) >>>>>>> [ 2.764772] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x000b), sas_addr(0x4433221103000000) >>>>>>> [ 2.765147] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 0) >>>>>>> [ 2.765891] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x000d), sas_addr(0x4433221104000000) >>>>>>> [ 2.767250] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 7) >>>>>>> [ 2.768009] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x0009), sas_addr(0x4433221105000000) >>>>>>> [ 2.768394] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 6) >>>>>>> [ 2.769136] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x000a), sas_addr(0x4433221106000000) >>>>>>> [ 2.769510] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 5) >>>>>>> [ 2.769888] mpt2sas_cm1: _scsih_determine_boot_device: current_boot_device(0x4433221106000000) >>>>>>> [ 2.770641] mpt2sas_cm1: _scsih_sas_device_init_add: handle(0x000c), sas_addr(0x4433221107000000) >>>>>>> [ 2.771025] mpt2sas_cm1: _scsih_sas_device_init_add: enclosure logical id(0x500605b0026f79b0), slot( 4) >>>>>>> [ 2.771405] mpt2sas_cm1: discovery event: (stop) >>>>>>> >>>>>>> [ 2.771788] mpt2sas_cm1: discovery event: (start) >>>>>>> >>>>>>> [ 2.772172] mpt2sas_cm1: discovery event: (stop) >>>>>>> >>>>>>> [ 2.772554] mpt2sas_cm1: discovery event: (start) >>>>>>> >>>>>>> [ 2.772942] mpt2sas_cm1: discovery event: (stop) >>>>>>> >>>>>>> [ 2.773326] mpt2sas_cm1: discovery event: (start) >>>>>>> >>>>>>> [ 2.773709] mpt2sas_cm1: discovery event: (stop) >>>>>>> >>>>>>> [ 2.774090] mpt2sas_cm1: discovery event: (start) >>>>>>> >>>>>>> [ 2.774474] mpt2sas_cm1: discovery event: (stop) >>>>>>> >>>>>>> [ 2.774855] mpt2sas_cm1: discovery event: (start) >>>>>>> >>>>>>> [ 2.775237] mpt2sas_cm1: discovery event: (stop) >>>>>>> >>>>>>> [ 2.775619] mpt2sas_cm1: port enable: complete from worker thread >>>>>>> [ 2.780192] mpt2sas_cm1: port enable: SUCCESS >>>>>>> [ 2.782404] scsi 1:0:0:0: Direct-Access ATA Hitachi HDP72505 A5BA PQ: 0 ANSI: 6 >>>>>>> [ 2.782651] scsi 1:0:0:0: SATA: handle(0x000a), sas_addr(0x4433221106000000), phy(6), device_name(0x5000cca34dc05584) >>>>>>> [ 2.783039] scsi 1:0:0:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(5) >>>>>>> [ 2.783390] scsi 1:0:0:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>>>> [ 2.803032] scsi 1:0:1:0: Direct-Access ATA ST8000AS0002-1NA AR15 PQ: 0 ANSI: 6 >>>>>>> [ 2.803272] scsi 1:0:1:0: SATA: handle(0x000e), sas_addr(0x4433221102000000), phy(2), device_name(0x5000c500908f1d05) >>>>>>> [ 2.803660] scsi 1:0:1:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(1) >>>>>>> [ 2.803981] scsi 1:0:1:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>>>> [ 2.821712] scsi 1:0:2:0: Direct-Access ATA ST3000DM001-1CH1 CC43 PQ: 0 ANSI: 6 >>>>>>> [ 2.821963] scsi 1:0:2:0: SATA: handle(0x000b), sas_addr(0x4433221103000000), phy(3), device_name(0x5000c5004dfd2a8a) >>>>>>> [ 2.822352] scsi 1:0:2:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(0) >>>>>>> [ 2.822694] scsi 1:0:2:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>>>> [ 2.844233] scsi 1:0:3:0: Direct-Access ATA ST3500320NS SN16 PQ: 0 ANSI: 6 >>>>>>> [ 2.844483] scsi 1:0:3:0: SATA: handle(0x000d), sas_addr(0x4433221104000000), phy(4), device_name(0x5000c50009dca65b) >>>>>>> [ 2.844870] scsi 1:0:3:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(7) >>>>>>> [ 2.845216] scsi 1:0:3:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>>>> [ 2.868963] scsi 1:0:4:0: Direct-Access ATA SAMSUNG HD401LJ 0-15 PQ: 0 ANSI: 6 >>>>>>> [ 2.870994] scsi 1:0:4:0: SATA: handle(0x0009), sas_addr(0x4433221105000000), phy(5), device_name(0x695d550daf678093) >>>>>>> [ 2.871382] scsi 1:0:4:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(6) >>>>>>> [ 2.871728] scsi 1:0:4:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>>>> [ 2.894004] scsi 1:0:5:0: Direct-Access ATA ST3750330NS SN06 PQ: 0 ANSI: 6 >>>>>>> [ 2.894257] scsi 1:0:5:0: SATA: handle(0x000c), sas_addr(0x4433221107000000), phy(7), device_name(0x5000c5000266bb02) >>>>>>> [ 2.894646] scsi 1:0:5:0: SATA: enclosure_logical_id(0x500605b0026f79b0), slot(4) >>>>>>> [ 2.894972] scsi 1:0:5:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>>> >>>>>> I don't see a clear pattern yet, but I suspect warm rebooting >=4.2 >>>>>> after having run 4.1.x leads to sucessful driver inits. But I also >>>>>> remember having had cold boots, with kernels >=4.2 that worked fine >>>>>> (obviously not all of the time). <=4.1.20 kernels on the other hand boot >>>>>> fine every single time. >>>>>> >>>>>> Interestingly the igb driver (ethernet) seems to be acting up at least >>>>>> with 4.5.0 on exactly the same boots when mpt2sas init fails. I don't >>>>>> know whether this could be connected or not (I just became aware of this >>>>>> coincidence). >>>>>> >>>>>> >>>>>> --- >>>>>> Matthias >>>>>> >>>>>> >>>>>> Am 21.03.2016 um 05:53 schrieb Sreekanth Reddy: >>>>>>> Hi Matthias, >>>>>>> >>>>>>> Can you please share us the driver logs with driver logging_level set >>>>>>> to 0x3f8. So that we can get more info from this log. >>>>>>> >>>>>>> Thanks, >>>>>>> Sreekanth >>>>>>> >>>>>>> On Mon, Mar 21, 2016 at 1:44 AM, Matthias Prager >>>>>>> <linux@matthiasprager.de> wrote: >>>>>>>> Hello, >>>>>>>> >>>>>>>> I don't know what's the correct procedure, whether I should file a bug or first report this issue on the kernel mailing-list. So please feel free to tell me to open a ticket in the bugtracker (bugzilla.kernel.org?). >>>>>>>> >>>>>>>> But first let me present the issue I encounter: >>>>>>>> >>>>>>>> Kernels >= 4.2 (4.2.1 was the first on I tried, but also 4.3, 4.4 and 4.5) fail to load the mpt2sas driver on most (but not all) boots. Kernels <= 4.1.x work fine every single time (4.1.19 was the latest I tried, also 3.18.29). >>>>>>>> >>>>>>>> Here is the dmesg output for a failed driver init with Kernel 4.5.0: >>>>>>>>> [ 2.068313] mpt3sas version 09.102.00.00 loaded >>>>>>>>> [ 2.069412] mpt2sas_cm0: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (3074748 kB) >>>>>>>>> [ 2.125260] mpt2sas_cm0: MSI-X vectors supported: 1, no of cores: 4, max_msix_vectors: -1 >>>>>>>>> [ 2.125996] mpt2sas0-msix0: PCI-MSI-X enabled: IRQ 58 >>>>>>>>> [ 2.126199] mpt2sas_cm0: iomem(0x00000000fd4fc000), mapped(0xffffc900000d0000), size(16384) >>>>>>>>> [ 2.126430] mpt2sas_cm0: ioport(0x0000000000004000), size(256) >>>>>>>>> [ 2.216371] mpt2sas_cm0: Allocated physical memory: size(4964 kB) >>>>>>>>> [ 2.216600] mpt2sas_cm0: Current Controller Queue Depth(3307),Max Controller Queue Depth(3432) >>>>>>>>> [ 2.217004] mpt2sas_cm0: Scatter Gather Elements per IO(128) >>>>>>>>> [ 5.086959] floppy0: no floppy controllers found >>>>>>>>> [ 32.256720] mpt2sas_cm0: _base_event_notification: timeout >>>>>>>>> [ 32.256940] mf: >>>>>>>>> >>>>>>>>> [ 32.257106] 07000000 >>>>>>>>> [ 32.257302] 00000000 >>>>>>>>> [ 32.257337] 00000000 >>>>>>>>> [ 32.257533] 00000000 >>>>>>>>> [ 32.257568] 00000000 >>>>>>>>> [ 32.257764] 0f2f7fff >>>>>>>>> [ 32.257800] ffffff7c >>>>>>>>> [ 32.257995] ffffffff >>>>>>>>> [ 32.258031] >>>>>>>>> >>>>>>>>> [ 32.258352] ffffffff >>>>>>>>> [ 32.258387] 00000000 >>>>>>>>> [ 32.258582] 00000000 >>>>>>>>> >>>>>>>>> [ 32.258950] mpt2sas_cm0: sending message unit reset !! >>>>>>>>> [ 32.260688] mpt2sas_cm0: message unit reset: SUCCESS >>>>>>>>> [ 32.325956] mpt2sas_cm0: failure at drivers/scsi/mpt3sas/mpt3sas_scsih.c:8592/_scsih_probe()! >>>>>>>> >>>>>>>> For comparison here is a dmesg output for a successful boot on Kernel 4.1.15: >>>>>>>>> [ 2.035568] mpt2sas version 20.100.00.00 loaded >>>>>>>>> [ 2.037243] mpt2sas0: 32 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (2046352 kB) >>>>>>>>> [ 2.755374] mpt2sas0: MSI-X vectors supported: 1, no of cores: 3, max_msix_vectors: 8 >>>>>>>>> [ 2.756377] mpt2sas0-msix0: PCI-MSI-X enabled: IRQ 58 >>>>>>>>> [ 2.756708] mpt2sas0: iomem(0x00000000fd5fc000), mapped(0xffffc900000d0000), size(16384) >>>>>>>>> [ 2.757083] mpt2sas0: ioport(0x0000000000004000), size(256) >>>>>>>>> [ 3.842944] mpt2sas0: Allocated physical memory: size(4964 kB) >>>>>>>>> [ 3.843303] mpt2sas0: Current Controller Queue Depth(3307), Max Controller Queue Depth(3432) >>>>>>>>> [ 3.843717] mpt2sas0: Scatter Gather Elements per IO(128) >>>>>>>>> [ 4.415980] mpt2sas0: LSISAS2008: FWVersion(20.00.04.00), ChipRevision(0x03), BiosVersion(07.39.00.00) >>>>>>>>> [ 4.416618] mpt2sas0: Protocol=(Initiator,Target), Capabilities=(TLR,EEDP,Snapshot Buffer,Diag Trace Buffer,Task Set Full,NCQ) >>>>>>>>> [ 4.417846] scsi host0: Fusion MPT SAS Host >>>>>>>>> [ 4.436865] mpt2sas0: sending port enable !! >>>>>>>>> [ 4.440460] mpt2sas0: host_add: handle(0x0001), sas_addr(0xxxxxxxxxxxxxxxxx), phys(8) >>>>>>>>> >>>>>>>>> ... >>>>>>>>> [ 4.444045] scsi 0:0:0:0: Direct-Access ATA Hitachi HDS5C302 A800 PQ: 0 ANSI: 6 >>>>>>>>> [ 4.444338] scsi 0:0:0:0: SATA: handle(0x0009), sas_addr(0xxxxxxxxxxxxxxxxx), phy(1), device_name(0xxxxxxxxxxxxxxxxx) >>>>>>>>> [ 4.444823] scsi 0:0:0:0: SATA: enclosure_logical_id(0xxxxxxxxxxxxxxxxx), slot(2) >>>>>>>>> [ 4.445197] scsi 0:0:0:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) >>>>>>>>> ... (n times for n drives) >>>>>>>>> >>>>>>>>> [ 4.515443] mpt2sas0: port enable: SUCCESS >>>>>>>> >>>>>>>> >>>>>>>> The Controller(s) are all Avego/LSI 9211-8i running the latest version of IT firmware (v20.00.04.00). These are passed through to a gentoo-linux VM on an ESXi 5.1 host (latest patchlevel). I have two of these systems (one production one testing) with nearly identical hardware (Supermicro X8DTi-F boards with 2x Intel Westmere CPUs). I also have an older set of systems running the same software config (Intel S3200SHLC boards with single Core2Quad) which exhibit the same buggy behavior. >>>>>>>> >>>>>>>> The 'uname -a' line on the current testing system looks like this: >>>>>>>>> Linux pserver2 4.1.19-gentoo #4 SMP Thu Mar 17 16:02:48 CET 2016 x86_64 Intel(R) Xeon(R) CPU E5506 @ 2.13GHz GenuineIntel GNU/Linux >>>>>>>> p >>>>>>>> >>>>>>>> There seem to be other people with similar issues: >>>>>>>> <https://bbs.archlinux.org/viewtopic.php?id=209495> >>>>>>>> >>>>>>>> Any thoughts? >>>>>>>> >>>>>>>> --- >>>>>>>> Matthias >>>>>> >>> ^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [BUG] mpt2sas: driver init fails on kernel >=4.2 for 9211-8i IT 2016-03-24 2:06 ` Matthias Prager @ 2016-03-24 6:06 ` Thomas Gleixner 2016-03-24 9:08 ` Matthias Prager 2016-03-24 11:02 ` Jason Taylor 0 siblings, 2 replies; 13+ messages in thread From: Thomas Gleixner @ 2016-03-24 6:06 UTC (permalink / raw) To: Matthias Prager; +Cc: Sreekanth Reddy, linux-scsi, Jason Taylor, LKML, x86 On Thu, 24 Mar 2016, Matthias Prager wrote: > The timeout happens reliably after two warm boots with a 'bad' kernel > after coming from a 'good' kernel, and also after one cold boot with a > 'bad' kernel (meaning cold booting a 'bad' kernel leads directly to the > timeout and warm booting needs a second run to produce the timeout). I > haven't tested bare metal yet - I can do that tomorrow if necessary. That's on VMWare, right? Jason has seen the same issue: http://marc.info/?l=linux-kernel&m=145280623530135&w=2 http://marc.info/?l=linux-kernel&m=145523785705624&w=2 "Works fine on real hardware and KVM. Filed an issue with VMware and the fix is in the works." Jason, what's the state of this? Thanks, tglx ^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [BUG] mpt2sas: driver init fails on kernel >=4.2 for 9211-8i IT 2016-03-24 6:06 ` Thomas Gleixner @ 2016-03-24 9:08 ` Matthias Prager 2016-03-24 11:02 ` Jason Taylor 1 sibling, 0 replies; 13+ messages in thread From: Matthias Prager @ 2016-03-24 9:08 UTC (permalink / raw) To: Thomas Gleixner Cc: Sreekanth Reddy, linux-scsi, Jason Taylor, LKML, x86, Matthias Prager Am 24.03.2016 um 07:06 schrieb Thomas Gleixner: > On Thu, 24 Mar 2016, Matthias Prager wrote: >> The timeout happens reliably after two warm boots with a 'bad' kernel >> after coming from a 'good' kernel, and also after one cold boot with a >> 'bad' kernel (meaning cold booting a 'bad' kernel leads directly to the >> timeout and warm booting needs a second run to produce the timeout). I >> haven't tested bare metal yet - I can do that tomorrow if necessary. > > That's on VMWare, right? Jason has seen the same issue: Correct ESXi 5.1 patchlevel 3070626 (the two controllers are passed through to the VM). > > http://marc.info/?l=linux-kernel&m=145280623530135&w=2 > http://marc.info/?l=linux-kernel&m=145523785705624&w=2 > > "Works fine on real hardware and KVM. Filed an issue with VMware and the fix > is in the works." > > Jason, what's the state of this? > > Thanks, > > tglx > ^ permalink raw reply [flat|nested] 13+ messages in thread
* RE: [BUG] mpt2sas: driver init fails on kernel >=4.2 for 9211-8i IT 2016-03-24 6:06 ` Thomas Gleixner 2016-03-24 9:08 ` Matthias Prager @ 2016-03-24 11:02 ` Jason Taylor 2016-06-20 11:13 ` Matthias Prager 1 sibling, 1 reply; 13+ messages in thread From: Jason Taylor @ 2016-03-24 11:02 UTC (permalink / raw) To: Thomas Gleixner, Matthias Prager; +Cc: Sreekanth Reddy, linux-scsi, LKML, x86 The last update we have from VMware is that the fix will be in 6.0p3/5.5p8 - both of which are targeted for a mid year release. -----Original Message----- From: Thomas Gleixner [mailto:tglx@linutronix.de] Sent: Thursday, March 24, 2016 2:06 AM To: Matthias Prager <linux@matthiasprager.de> Cc: Sreekanth Reddy <sreekanth.reddy@broadcom.com>; linux-scsi <linux-scsi@vger.kernel.org>; Jason Taylor <jason.taylor@simplivity.com>; LKML <linux-kernel@vger.kernel.org>; x86@kernel.org Subject: Re: [BUG] mpt2sas: driver init fails on kernel >=4.2 for 9211-8i IT On Thu, 24 Mar 2016, Matthias Prager wrote: > The timeout happens reliably after two warm boots with a 'bad' kernel > after coming from a 'good' kernel, and also after one cold boot with a > 'bad' kernel (meaning cold booting a 'bad' kernel leads directly to > the timeout and warm booting needs a second run to produce the > timeout). I haven't tested bare metal yet - I can do that tomorrow if necessary. That's on VMWare, right? Jason has seen the same issue: http://marc.info/?l=linux-kernel&m=145280623530135&w=2 http://marc.info/?l=linux-kernel&m=145523785705624&w=2 "Works fine on real hardware and KVM. Filed an issue with VMware and the fix is in the works." Jason, what's the state of this? Thanks, tglx --------------------------------------------------------------------------------------- PRIVACY STATEMENT: This message is a PRIVATE communication. This message and all attachments are a private communication sent by SimpliVity and are considered to be confidential or protected by privilege. If you are not the intended recipient, you are hereby notified that any disclosure, copying, distribution or use of the information contained in or attached to this message is strictly prohibited. Please notify the sender of the delivery error by replying to this message, and then delete it from your system. --------------------------------------------------------------------------------------- ^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [BUG] mpt2sas: driver init fails on kernel >=4.2 for 9211-8i IT 2016-03-24 11:02 ` Jason Taylor @ 2016-06-20 11:13 ` Matthias Prager 0 siblings, 0 replies; 13+ messages in thread From: Matthias Prager @ 2016-06-20 11:13 UTC (permalink / raw) To: Jason Taylor, Thomas Gleixner; +Cc: Sreekanth Reddy, linux-scsi, LKML, x86 Still tracking - small update: So far with the most current esxi 6 (build 3825889 - 2016-05-12) the fix is not there yet. Sidenote: the mpt driver seems to have learned to work around the irq handling issues (I tested kernel 4.6.2) whereas the e1000e ethernet driver still has trouble initializing. ... patiently waiting for VMware to release 6.0 update 3. Am 24.03.2016 um 12:02 schrieb Jason Taylor: > The last update we have from VMware is that the fix will be in 6.0p3/5.5p8 - both of which are targeted for a mid year release. > > -----Original Message----- > From: Thomas Gleixner [mailto:tglx@linutronix.de] > Sent: Thursday, March 24, 2016 2:06 AM > To: Matthias Prager <linux@matthiasprager.de> > Cc: Sreekanth Reddy <sreekanth.reddy@broadcom.com>; linux-scsi <linux-scsi@vger.kernel.org>; Jason Taylor <jason.taylor@simplivity.com>; LKML <linux-kernel@vger.kernel.org>; x86@kernel.org > Subject: Re: [BUG] mpt2sas: driver init fails on kernel >=4.2 for 9211-8i IT > > On Thu, 24 Mar 2016, Matthias Prager wrote: >> The timeout happens reliably after two warm boots with a 'bad' kernel >> after coming from a 'good' kernel, and also after one cold boot with a >> 'bad' kernel (meaning cold booting a 'bad' kernel leads directly to >> the timeout and warm booting needs a second run to produce the >> timeout). I haven't tested bare metal yet - I can do that tomorrow if necessary. > > That's on VMWare, right? Jason has seen the same issue: > > http://marc.info/?l=linux-kernel&m=145280623530135&w=2 > http://marc.info/?l=linux-kernel&m=145523785705624&w=2 > > "Works fine on real hardware and KVM. Filed an issue with VMware and the fix > is in the works." > > Jason, what's the state of this? > > Thanks, > > tglx > --------------------------------------------------------------------------------------- > PRIVACY STATEMENT: > This message is a PRIVATE communication. This message and all attachments are a private communication sent by SimpliVity and are considered to be confidential or protected by privilege. If you are not the intended recipient, you are hereby notified that any disclosure, copying, distribution or use of the information contained in or attached to this message is strictly prohibited. Please notify the sender of the delivery error by replying to this message, and then delete it from your system. > --------------------------------------------------------------------------------------- > ^ permalink raw reply [flat|nested] 13+ messages in thread
end of thread, other threads:[~2016-06-20 11:21 UTC | newest] Thread overview: 13+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2016-03-20 20:14 [BUG] mpt2sas: driver init fails on kernel >=4.2 for 9211-8i IT Matthias Prager 2016-03-21 4:53 ` Sreekanth Reddy 2016-03-21 9:18 ` Matthias Prager 2016-03-21 13:59 ` Sreekanth Reddy 2016-03-21 15:52 ` Matthias Prager 2016-03-21 16:30 ` Matthias Prager 2016-03-22 10:52 ` Sreekanth Reddy 2016-03-22 21:02 ` Matthias Prager 2016-03-24 2:06 ` Matthias Prager 2016-03-24 6:06 ` Thomas Gleixner 2016-03-24 9:08 ` Matthias Prager 2016-03-24 11:02 ` Jason Taylor 2016-06-20 11:13 ` Matthias Prager
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.