[PATCH v2 0/5] RZ/G2L: pinctrl: Support to get/set drive-strength and output-impedance-ohms

[PATCH v2 0/5] RZ/G2L: pinctrl: Support to get/set drive-strength and output-impedance-ohms

[Lad Prabhakar]

Hi All,

This patch series add support to get/set drive-strength and
output-impedance for RZ/G2L SoC. Along with some macro renames
and code cleanup.

Cheers,
Prabhakar

Changes for v2:
* Fixed review comments pointed by Geert, split up patch 4 from series [1]

Note: This patch series is dependent on first two patches of series [1]

[1] https://patchwork.kernel.org/project/linux-renesas-soc/cover/
20211027134509.5036-1-prabhakar.mahadev-lad.rj@bp.renesas.com/

Lad Prabhakar (5):
  dt-bindings: pinctrl: renesas,rzg2l-pinctrl: Add output-impedance-ohms
    property
  pinctrl: renesas: pinctrl-rzg2l: Add helper functions to read/write
    pin config
  pinctrl: renesas: pinctrl-rzg2l: Add support to get/set pin config for
    GPIO port pins
  pinctrl: renesas: pinctrl-rzg2l: Rename PIN_CFG_* macros to match HW
    manual
  pinctrl: renesas: pinctrl-rzg2l: Add support to get/set drive-strength
    and output-impedance-ohms

 .../pinctrl/renesas,rzg2l-pinctrl.yaml        |   2 +
 drivers/pinctrl/renesas/pinctrl-rzg2l.c       | 316 ++++++++++++------
 2 files changed, 222 insertions(+), 96 deletions(-)

-- 
2.17.1

[PATCH v2 1/5] dt-bindings: pinctrl: renesas,rzg2l-pinctrl: Add output-impedance-ohms property

[Lad Prabhakar]

RZ/G2L SoC has two groups of pins, Group-A and Group-B. RZ/G2L SoC supports
configuring Output Impedance for Group-B pins (valid values 33/50/66/100).

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
---
 .../devicetree/bindings/pinctrl/renesas,rzg2l-pinctrl.yaml      | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,rzg2l-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/renesas,rzg2l-pinctrl.yaml
index ef68dabcf4dc..3a66fd214c17 100644
--- a/Documentation/devicetree/bindings/pinctrl/renesas,rzg2l-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/renesas,rzg2l-pinctrl.yaml
@@ -73,6 +73,8 @@ additionalProperties:
         pins: true
         drive-strength:
           enum: [ 2, 4, 8, 12 ]
+        output-impedance-ohms:
+          enum: [ 33, 50, 66, 100 ]
         power-source:
           enum: [ 1800, 2500, 3300 ]
         slew-rate: true
-- 
2.17.1

Re: [PATCH v2 1/5] dt-bindings: pinctrl: renesas,rzg2l-pinctrl: Add output-impedance-ohms property

[Rob Herring]

On Fri, 29 Oct 2021 13:44:33 +0100, Lad Prabhakar wrote:
> RZ/G2L SoC has two groups of pins, Group-A and Group-B. RZ/G2L SoC supports
> configuring Output Impedance for Group-B pins (valid values 33/50/66/100).
> 
> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
> Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
> ---
>  .../devicetree/bindings/pinctrl/renesas,rzg2l-pinctrl.yaml      | 2 ++
>  1 file changed, 2 insertions(+)
> 

Reviewed-by: Rob Herring <robh@kernel.org>

[PATCH v2 2/5] pinctrl: renesas: pinctrl-rzg2l: Add helper functions to read/write pin config

[Lad Prabhakar]

Add helper functions to read/read modify write pin config.

Switch to use helper functions for pins supporting PIN_CONFIG_INPUT_ENABLE
capabilities.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
---
 drivers/pinctrl/renesas/pinctrl-rzg2l.c | 78 +++++++++++++++++--------
 1 file changed, 54 insertions(+), 24 deletions(-)

diff --git a/drivers/pinctrl/renesas/pinctrl-rzg2l.c b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
index 20b2af889ca9..f294ae7b8b5a 100644
--- a/drivers/pinctrl/renesas/pinctrl-rzg2l.c
+++ b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
@@ -91,6 +91,8 @@
 #define SD_CH(n)		(0x3000 + (n) * 4)
 #define QSPI			(0x3008)
 
+#define PORT_PIN_CFG_OFFSET	0x80
+
 #define PVDD_1800		1	/* I/O domain voltage <= 1.8V */
 #define PVDD_3300		0	/* I/O domain voltage >= 3.3V */
 
@@ -424,6 +426,52 @@ static int rzg2l_dt_node_to_map(struct pinctrl_dev *pctldev,
 	return ret;
 }
 
+static u32 rzg2l_read_pin_config(struct rzg2l_pinctrl *pctrl, bool port_pin,
+				 u32 offset, u8 bit, u32 mask)
+{
+	void __iomem *addr = pctrl->base + offset;
+	unsigned long flags;
+	u32 reg;
+
+	if (port_pin)
+		addr += PORT_PIN_CFG_OFFSET;
+
+	/* handle _L/_H for 32-bit register read/write */
+	if (bit >= 4) {
+		bit -= 4;
+		addr += 4;
+	}
+
+	spin_lock_irqsave(&pctrl->lock, flags);
+	reg = readl(addr) & (mask << (bit * 8));
+	spin_unlock_irqrestore(&pctrl->lock, flags);
+	reg = (reg >> (bit * 8)) & mask;
+
+	return reg;
+}
+
+static void rzg2l_rmw_pin_config(struct rzg2l_pinctrl *pctrl, bool port_pin,
+				 u32 offset, u8 bit, u32 mask, u32 val)
+{
+	void __iomem *addr = pctrl->base + offset;
+	unsigned long flags;
+	u32 reg;
+
+	if (port_pin)
+		addr += PORT_PIN_CFG_OFFSET;
+
+	/* handle _L/_H for 32-bit register read/write */
+	if (bit >= 4) {
+		bit -= 4;
+		addr += 4;
+	}
+
+	spin_lock_irqsave(&pctrl->lock, flags);
+	reg = readl(addr) & ~(mask << (bit * 8));
+	writel(reg | (val << (bit * 8)), addr);
+	spin_unlock_irqrestore(&pctrl->lock, flags);
+}
+
 static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
 				     unsigned int _pin,
 				     unsigned long *config)
@@ -432,10 +480,11 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
 	enum pin_config_param param = pinconf_to_config_param(*config);
 	const struct pinctrl_pin_desc *pin = &pctrl->desc.pins[_pin];
 	unsigned int *pin_data = pin->drv_data;
+	bool port_pin = false;
 	unsigned int arg = 0;
 	unsigned long flags;
 	void __iomem *addr;
-	u32 port = 0, reg;
+	u32 port = 0;
 	u32 cfg = 0;
 	u8 bit = 0;
 
@@ -452,17 +501,8 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
 	case PIN_CONFIG_INPUT_ENABLE:
 		if (!(cfg & PIN_CFG_IEN))
 			return -EINVAL;
-		spin_lock_irqsave(&pctrl->lock, flags);
-		/* handle _L/_H for 32-bit register read/write */
-		addr = pctrl->base + IEN(port);
-		if (bit >= 4) {
-			bit -= 4;
-			addr += 4;
-		}
 
-		reg = readl(addr) & (IEN_MASK << (bit * 8));
-		arg = (reg >> (bit * 8)) & 0x1;
-		spin_unlock_irqrestore(&pctrl->lock, flags);
+		arg = rzg2l_read_pin_config(pctrl, port_pin, IEN(port), bit, IEN_MASK);
 		break;
 
 	case PIN_CONFIG_POWER_SOURCE: {
@@ -502,10 +542,11 @@ static int rzg2l_pinctrl_pinconf_set(struct pinctrl_dev *pctldev,
 	const struct pinctrl_pin_desc *pin = &pctrl->desc.pins[_pin];
 	unsigned int *pin_data = pin->drv_data;
 	enum pin_config_param param;
+	bool port_pin = false;
 	unsigned long flags;
 	void __iomem *addr;
-	u32 port = 0, reg;
 	unsigned int i;
+	u32 port = 0;
 	u32 cfg = 0;
 	u8 bit = 0;
 
@@ -524,21 +565,10 @@ static int rzg2l_pinctrl_pinconf_set(struct pinctrl_dev *pctldev,
 		case PIN_CONFIG_INPUT_ENABLE: {
 			unsigned int arg =
 					pinconf_to_config_argument(_configs[i]);
-
 			if (!(cfg & PIN_CFG_IEN))
 				return -EINVAL;
 
-			/* handle _L/_H for 32-bit register read/write */
-			addr = pctrl->base + IEN(port);
-			if (bit >= 4) {
-				bit -= 4;
-				addr += 4;
-			}
-
-			spin_lock_irqsave(&pctrl->lock, flags);
-			reg = readl(addr) & ~(IEN_MASK << (bit * 8));
-			writel(reg | (arg << (bit * 8)), addr);
-			spin_unlock_irqrestore(&pctrl->lock, flags);
+			rzg2l_rmw_pin_config(pctrl, port_pin, IEN(port), bit, IEN_MASK, !!arg);
 			break;
 		}
 
-- 
2.17.1

Re: [PATCH v2 2/5] pinctrl: renesas: pinctrl-rzg2l: Add helper functions to read/write pin config

[Geert Uytterhoeven]

Hi Prabhakar,

On Fri, Oct 29, 2021 at 2:44 PM Lad Prabhakar
<prabhakar.mahadev-lad.rj@bp.renesas.com> wrote:
> Add helper functions to read/read modify write pin config.
>
> Switch to use helper functions for pins supporting PIN_CONFIG_INPUT_ENABLE
> capabilities.
>
> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>

Thanks for your patch!

> --- a/drivers/pinctrl/renesas/pinctrl-rzg2l.c
> +++ b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
> @@ -91,6 +91,8 @@
>  #define SD_CH(n)               (0x3000 + (n) * 4)
>  #define QSPI                   (0x3008)
>
> +#define PORT_PIN_CFG_OFFSET    0x80

This definition belongs in [PATCH v2 5/5].

> +
>  #define PVDD_1800              1       /* I/O domain voltage <= 1.8V */
>  #define PVDD_3300              0       /* I/O domain voltage >= 3.3V */
>
> @@ -424,6 +426,52 @@ static int rzg2l_dt_node_to_map(struct pinctrl_dev *pctldev,
>         return ret;
>  }
>
> +static u32 rzg2l_read_pin_config(struct rzg2l_pinctrl *pctrl, bool port_pin,
> +                                u32 offset, u8 bit, u32 mask)
> +{
> +       void __iomem *addr = pctrl->base + offset;
> +       unsigned long flags;
> +       u32 reg;
> +
> +       if (port_pin)
> +               addr += PORT_PIN_CFG_OFFSET;

I'm wondering if it would be better to handle this in the caller,
by passing an adjusted offset?
Same for rzg2l_rmw_pin_config().

> +
> +       /* handle _L/_H for 32-bit register read/write */
> +       if (bit >= 4) {
> +               bit -= 4;
> +               addr += 4;
> +       }
> +
> +       spin_lock_irqsave(&pctrl->lock, flags);
> +       reg = readl(addr) & (mask << (bit * 8));

The masking is not needed here, as it is done below.

> +       spin_unlock_irqrestore(&pctrl->lock, flags);

I still think you don't need that spinlock here, as reading a MMIO
register is an atomic operation.

(/me fixes drivers/pinctrl/renesas/pinctrl.c you referred to before)

> +       reg = (reg >> (bit * 8)) & mask;
> +
> +       return reg;

return (reg >> (bit * 8)) & mask;

> +}

> @@ -432,10 +480,11 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
>         enum pin_config_param param = pinconf_to_config_param(*config);
>         const struct pinctrl_pin_desc *pin = &pctrl->desc.pins[_pin];
>         unsigned int *pin_data = pin->drv_data;
> +       bool port_pin = false;

Do you really need this?

>         unsigned int arg = 0;
>         unsigned long flags;
>         void __iomem *addr;
> -       u32 port = 0, reg;
> +       u32 port = 0;
>         u32 cfg = 0;
>         u8 bit = 0;
>
> @@ -452,17 +501,8 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
>         case PIN_CONFIG_INPUT_ENABLE:
>                 if (!(cfg & PIN_CFG_IEN))
>                         return -EINVAL;
> -               spin_lock_irqsave(&pctrl->lock, flags);
> -               /* handle _L/_H for 32-bit register read/write */
> -               addr = pctrl->base + IEN(port);
> -               if (bit >= 4) {
> -                       bit -= 4;
> -                       addr += 4;
> -               }
>
> -               reg = readl(addr) & (IEN_MASK << (bit * 8));
> -               arg = (reg >> (bit * 8)) & 0x1;
> -               spin_unlock_irqrestore(&pctrl->lock, flags);
> +               arg = rzg2l_read_pin_config(pctrl, port_pin, IEN(port), bit, IEN_MASK);

port_pin is always false here, as PIN_CFG_IEN is only ever set for
dedicated pins.

Same comments for rzg2l_pinctrl_pinconf_set().

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

[PATCH v2 3/5] pinctrl: renesas: pinctrl-rzg2l: Add support to get/set pin config for GPIO port pins

[Lad Prabhakar]

Add support to get/set pin config for GPIO port pins.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
---
 drivers/pinctrl/renesas/pinctrl-rzg2l.c | 33 +++++++++++++++++++++++++
 1 file changed, 33 insertions(+)

diff --git a/drivers/pinctrl/renesas/pinctrl-rzg2l.c b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
index f294ae7b8b5a..bc34c63bbb36 100644
--- a/drivers/pinctrl/renesas/pinctrl-rzg2l.c
+++ b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
@@ -426,6 +426,23 @@ static int rzg2l_dt_node_to_map(struct pinctrl_dev *pctldev,
 	return ret;
 }
 
+static int rzg2l_validate_gpio_pin(struct rzg2l_pinctrl *pctrl,
+				   u32 cfg, u32 port, u8 bit)
+{
+	u8 pincount = RZG2L_GPIO_PORT_GET_PINCNT(cfg);
+	u32 port_index = RZG2L_GPIO_PORT_GET_INDEX(cfg);
+	u32 data;
+
+	if (bit >= pincount || port >= pctrl->data->n_port_pins)
+		return -EINVAL;
+
+	data = pctrl->data->port_pin_configs[port];
+	if (port_index != RZG2L_GPIO_PORT_GET_INDEX(data))
+		return -EINVAL;
+
+	return 0;
+}
+
 static u32 rzg2l_read_pin_config(struct rzg2l_pinctrl *pctrl, bool port_pin,
 				 u32 offset, u8 bit, u32 mask)
 {
@@ -495,6 +512,14 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
 		port = RZG2L_SINGLE_PIN_GET_PORT(*pin_data);
 		cfg = RZG2L_SINGLE_PIN_GET_CFGS(*pin_data);
 		bit = RZG2L_SINGLE_PIN_GET_BIT(*pin_data);
+	} else {
+		cfg = RZG2L_GPIO_PORT_GET_CFGS(*pin_data);
+		port = RZG2L_PIN_ID_TO_PORT(_pin);
+		bit = RZG2L_PIN_ID_TO_PIN(_pin);
+		port_pin = true;
+
+		if (rzg2l_validate_gpio_pin(pctrl, *pin_data, port, bit))
+			return -EINVAL;
 	}
 
 	switch (param) {
@@ -557,6 +582,14 @@ static int rzg2l_pinctrl_pinconf_set(struct pinctrl_dev *pctldev,
 		port = RZG2L_SINGLE_PIN_GET_PORT(*pin_data);
 		cfg = RZG2L_SINGLE_PIN_GET_CFGS(*pin_data);
 		bit = RZG2L_SINGLE_PIN_GET_BIT(*pin_data);
+	} else {
+		cfg = RZG2L_GPIO_PORT_GET_CFGS(*pin_data);
+		port = RZG2L_PIN_ID_TO_PORT(_pin);
+		bit = RZG2L_PIN_ID_TO_PIN(_pin);
+		port_pin = true;
+
+		if (rzg2l_validate_gpio_pin(pctrl, *pin_data, port, bit))
+			return -EINVAL;
 	}
 
 	for (i = 0; i < num_configs; i++) {
-- 
2.17.1

Re: [PATCH v2 3/5] pinctrl: renesas: pinctrl-rzg2l: Add support to get/set pin config for GPIO port pins

[Geert Uytterhoeven]

Hi Prabhakar,

On Fri, Oct 29, 2021 at 2:44 PM Lad Prabhakar
<prabhakar.mahadev-lad.rj@bp.renesas.com> wrote:
> Add support to get/set pin config for GPIO port pins.
>
> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>

Thanks for your patch!

> --- a/drivers/pinctrl/renesas/pinctrl-rzg2l.c
> +++ b/drivers/pinctrl/renesas/pinctrl-rzg2l.c

> @@ -495,6 +512,14 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
>                 port = RZG2L_SINGLE_PIN_GET_PORT(*pin_data);
>                 cfg = RZG2L_SINGLE_PIN_GET_CFGS(*pin_data);
>                 bit = RZG2L_SINGLE_PIN_GET_BIT(*pin_data);
> +       } else {
> +               cfg = RZG2L_GPIO_PORT_GET_CFGS(*pin_data);
> +               port = RZG2L_PIN_ID_TO_PORT(_pin);
> +               bit = RZG2L_PIN_ID_TO_PIN(_pin);
> +               port_pin = true;

Instead of setting this flag, perhaps port should be adjusted?
Then rzg2l_r{ead,mw}_pin_config() don't have to care about that
anymore.

> +
> +               if (rzg2l_validate_gpio_pin(pctrl, *pin_data, port, bit))
> +                       return -EINVAL;
>         }
>
>         switch (param) {
> @@ -557,6 +582,14 @@ static int rzg2l_pinctrl_pinconf_set(struct pinctrl_dev *pctldev,
>                 port = RZG2L_SINGLE_PIN_GET_PORT(*pin_data);
>                 cfg = RZG2L_SINGLE_PIN_GET_CFGS(*pin_data);
>                 bit = RZG2L_SINGLE_PIN_GET_BIT(*pin_data);
> +       } else {
> +               cfg = RZG2L_GPIO_PORT_GET_CFGS(*pin_data);
> +               port = RZG2L_PIN_ID_TO_PORT(_pin);
> +               bit = RZG2L_PIN_ID_TO_PIN(_pin);
> +               port_pin = true;

Likewise.

> +
> +               if (rzg2l_validate_gpio_pin(pctrl, *pin_data, port, bit))
> +                       return -EINVAL;
>         }
>
>         for (i = 0; i < num_configs; i++) {

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

Re: [PATCH v2 3/5] pinctrl: renesas: pinctrl-rzg2l: Add support to get/set pin config for GPIO port pins

[Lad, Prabhakar]

Hi Geert,

Thank you for the review.

On Mon, Nov 8, 2021 at 3:36 PM Geert Uytterhoeven <geert@linux-m68k.org> wrote:
>
> Hi Prabhakar,
>
> On Fri, Oct 29, 2021 at 2:44 PM Lad Prabhakar
> <prabhakar.mahadev-lad.rj@bp.renesas.com> wrote:
> > Add support to get/set pin config for GPIO port pins.
> >
> > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> > Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
>
> Thanks for your patch!
>
> > --- a/drivers/pinctrl/renesas/pinctrl-rzg2l.c
> > +++ b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
>
> > @@ -495,6 +512,14 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
> >                 port = RZG2L_SINGLE_PIN_GET_PORT(*pin_data);
> >                 cfg = RZG2L_SINGLE_PIN_GET_CFGS(*pin_data);
> >                 bit = RZG2L_SINGLE_PIN_GET_BIT(*pin_data);
> > +       } else {
> > +               cfg = RZG2L_GPIO_PORT_GET_CFGS(*pin_data);
> > +               port = RZG2L_PIN_ID_TO_PORT(_pin);
> > +               bit = RZG2L_PIN_ID_TO_PIN(_pin);
> > +               port_pin = true;
>
> Instead of setting this flag, perhaps port should be adjusted?

Something like below?

#define RZG2L_PORT_START_OFFSET 0x10

port = RZG2L_PIN_ID_TO_PORT_pin) + RZG2L_PORT_START_OFFSET;
rzg2l_validate_gpio_pin(pctrl, *pin_data, port - RZG2L_PORT_START_OFFSET, bit)

and rename port -> port_offset in rzg2l_pinctrl_pinconf_get/set Or
would you prefer to change the RZG2L_PIN_ID_TO_PORT macro and adjust
the entire file?

> Then rzg2l_r{ead,mw}_pin_config() don't have to care about that
> anymore.
>
Agreed.

Cheers,
Prabhakar

> > +
> > +               if (rzg2l_validate_gpio_pin(pctrl, *pin_data, port, bit))
> > +                       return -EINVAL;
> >         }
> >
> >         switch (param) {
> > @@ -557,6 +582,14 @@ static int rzg2l_pinctrl_pinconf_set(struct pinctrl_dev *pctldev,
> >                 port = RZG2L_SINGLE_PIN_GET_PORT(*pin_data);
> >                 cfg = RZG2L_SINGLE_PIN_GET_CFGS(*pin_data);
> >                 bit = RZG2L_SINGLE_PIN_GET_BIT(*pin_data);
> > +       } else {
> > +               cfg = RZG2L_GPIO_PORT_GET_CFGS(*pin_data);
> > +               port = RZG2L_PIN_ID_TO_PORT(_pin);
> > +               bit = RZG2L_PIN_ID_TO_PIN(_pin);
> > +               port_pin = true;
>
> Likewise.
>
> > +
> > +               if (rzg2l_validate_gpio_pin(pctrl, *pin_data, port, bit))
> > +                       return -EINVAL;
> >         }
> >
> >         for (i = 0; i < num_configs; i++) {
>
> Gr{oetje,eeting}s,
>
>                         Geert
>
> --
> Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
>
> In personal conversations with technical people, I call myself a hacker. But
> when I'm talking to journalists I just say "programmer" or something like that.
>                                 -- Linus Torvalds

Re: [PATCH v2 3/5] pinctrl: renesas: pinctrl-rzg2l: Add support to get/set pin config for GPIO port pins

[Geert Uytterhoeven]

Hi Prabhakar,

On Tue, Nov 9, 2021 at 3:31 PM Lad, Prabhakar
<prabhakar.csengg@gmail.com> wrote:
> On Mon, Nov 8, 2021 at 3:36 PM Geert Uytterhoeven <geert@linux-m68k.org> wrote:
> > On Fri, Oct 29, 2021 at 2:44 PM Lad Prabhakar
> > <prabhakar.mahadev-lad.rj@bp.renesas.com> wrote:
> > > Add support to get/set pin config for GPIO port pins.
> > >
> > > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> > > Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
> >
> > Thanks for your patch!
> >
> > > --- a/drivers/pinctrl/renesas/pinctrl-rzg2l.c
> > > +++ b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
> >
> > > @@ -495,6 +512,14 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
> > >                 port = RZG2L_SINGLE_PIN_GET_PORT(*pin_data);
> > >                 cfg = RZG2L_SINGLE_PIN_GET_CFGS(*pin_data);
> > >                 bit = RZG2L_SINGLE_PIN_GET_BIT(*pin_data);
> > > +       } else {
> > > +               cfg = RZG2L_GPIO_PORT_GET_CFGS(*pin_data);
> > > +               port = RZG2L_PIN_ID_TO_PORT(_pin);
> > > +               bit = RZG2L_PIN_ID_TO_PIN(_pin);
> > > +               port_pin = true;
> >
> > Instead of setting this flag, perhaps port should be adjusted?
>
> Something like below?
>
> #define RZG2L_PORT_START_OFFSET 0x10
>
> port = RZG2L_PIN_ID_TO_PORT_pin) + RZG2L_PORT_START_OFFSET;
> rzg2l_validate_gpio_pin(pctrl, *pin_data, port - RZG2L_PORT_START_OFFSET, bit)

Or adjust port after the call to rzg2l_validate_gpio_pin(), to avoid adding
the offset first, and subtracting it again for calling the latter?

> and rename port -> port_offset in rzg2l_pinctrl_pinconf_get/set

That makes sense.  Currently "port" has two meanings: it can mean
either the GPIO port index, or the global register index covering both
single function pin groups and GPIO port indices.
RZG2L_SINGLE_PIN_GET_PORT() returns the latter.
RZG2L_PIN_ID_TO_PORT() returns the former, thus needing an extra offset
to convert to the global register index.

> Or
> would you prefer to change the RZG2L_PIN_ID_TO_PORT macro and adjust
> the entire file?

Changing RZG2L_PIN_ID_TO_PORT() would imply changing all macros
accessing GPIO registers, and is thus quite intrusive.

> > Then rzg2l_r{ead,mw}_pin_config() don't have to care about that
> > anymore.
> >
> Agreed.

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

Re: [PATCH v2 3/5] pinctrl: renesas: pinctrl-rzg2l: Add support to get/set pin config for GPIO port pins

[Lad, Prabhakar]

Hi Geert,

On Tue, Nov 9, 2021 at 3:00 PM Geert Uytterhoeven <geert@linux-m68k.org> wrote:
>
> Hi Prabhakar,
>
> On Tue, Nov 9, 2021 at 3:31 PM Lad, Prabhakar
> <prabhakar.csengg@gmail.com> wrote:
> > On Mon, Nov 8, 2021 at 3:36 PM Geert Uytterhoeven <geert@linux-m68k.org> wrote:
> > > On Fri, Oct 29, 2021 at 2:44 PM Lad Prabhakar
> > > <prabhakar.mahadev-lad.rj@bp.renesas.com> wrote:
> > > > Add support to get/set pin config for GPIO port pins.
> > > >
> > > > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> > > > Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
> > >
> > > Thanks for your patch!
> > >
> > > > --- a/drivers/pinctrl/renesas/pinctrl-rzg2l.c
> > > > +++ b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
> > >
> > > > @@ -495,6 +512,14 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
> > > >                 port = RZG2L_SINGLE_PIN_GET_PORT(*pin_data);
> > > >                 cfg = RZG2L_SINGLE_PIN_GET_CFGS(*pin_data);
> > > >                 bit = RZG2L_SINGLE_PIN_GET_BIT(*pin_data);
> > > > +       } else {
> > > > +               cfg = RZG2L_GPIO_PORT_GET_CFGS(*pin_data);
> > > > +               port = RZG2L_PIN_ID_TO_PORT(_pin);
> > > > +               bit = RZG2L_PIN_ID_TO_PIN(_pin);
> > > > +               port_pin = true;
> > >
> > > Instead of setting this flag, perhaps port should be adjusted?
> >
> > Something like below?
> >
> > #define RZG2L_PORT_START_OFFSET 0x10
> >
> > port = RZG2L_PIN_ID_TO_PORT_pin) + RZG2L_PORT_START_OFFSET;
> > rzg2l_validate_gpio_pin(pctrl, *pin_data, port - RZG2L_PORT_START_OFFSET, bit)
>
> Or adjust port after the call to rzg2l_validate_gpio_pin(), to avoid adding
> the offset first, and subtracting it again for calling the latter?
>
> > and rename port -> port_offset in rzg2l_pinctrl_pinconf_get/set
>
> That makes sense.  Currently "port" has two meanings: it can mean
> either the GPIO port index, or the global register index covering both
> single function pin groups and GPIO port indices.
> RZG2L_SINGLE_PIN_GET_PORT() returns the latter.
> RZG2L_PIN_ID_TO_PORT() returns the former, thus needing an extra offset
> to convert to the global register index.
>
for symmetry will rename the below:
RZG2L_SINGLE_PIN_GET_PORT -> RZG2L_SINGLE_PIN_GET_PORT_OFFSET

Introduce a new macros:
#define RZG2L_PORT_START_OFFSET 0x10
#define RZG2L_PIN_ID_TO_PORT_OFFSET(id) (((id) / RZG2L_PINS_PER_PORT)
+ RZG2L_PORT_START_OFFSET)

And use the above two in rzg2l_pinctrl_pinconf_get/set along with
renaming  port -> port_offset

And for rzg2l_validate_gpio_pin() will use below instead:
rzg2l_validate_gpio_pin(pctrl, *pin_data, RZG2L_PIN_ID_TO_PORT(_pin), bit);

> > Or
> > would you prefer to change the RZG2L_PIN_ID_TO_PORT macro and adjust
> > the entire file?
>
> Changing RZG2L_PIN_ID_TO_PORT() would imply changing all macros
> accessing GPIO registers, and is thus quite intrusive.
>
Agreed, I will drop this option.

Cheers,
Prabhakar
> > > Then rzg2l_r{ead,mw}_pin_config() don't have to care about that
> > > anymore.
> > >
> > Agreed.
>
> Gr{oetje,eeting}s,
>
>                         Geert
>
> --
> Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
>
> In personal conversations with technical people, I call myself a hacker. But
> when I'm talking to journalists I just say "programmer" or something like that.
>                                 -- Linus Torvalds

[PATCH v2 4/5] pinctrl: renesas: pinctrl-rzg2l: Rename PIN_CFG_* macros to match HW manual

[Lad Prabhakar]

Rename the below macros to match the HW manual (Rev.1.00):
PIN_CFG_IOLH_SD0 -> PIN_CFG_IO_VMC_SD0
PIN_CFG_IOLH_SD1 -> PIN_CFG_IO_VMC_SD1
PIN_CFG_IOLH_QSPI -> PIN_CFG_IO_VMC_QSPI
PIN_CFG_IOLH_ETH0 -> PIN_CFG_IO_VMC_ETH0
PIN_CFG_IOLH_ETH1 -> PIN_CFG_IO_VMC_ETH1

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
---
 drivers/pinctrl/renesas/pinctrl-rzg2l.c | 122 ++++++++++++------------
 1 file changed, 61 insertions(+), 61 deletions(-)

diff --git a/drivers/pinctrl/renesas/pinctrl-rzg2l.c b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
index bc34c63bbb36..348fc8dd74e6 100644
--- a/drivers/pinctrl/renesas/pinctrl-rzg2l.c
+++ b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
@@ -39,11 +39,11 @@
 #define PIN_CFG_SR			BIT(1)
 #define PIN_CFG_IEN			BIT(2)
 #define PIN_CFG_PUPD			BIT(3)
-#define PIN_CFG_IOLH_SD0		BIT(4)
-#define PIN_CFG_IOLH_SD1		BIT(5)
-#define PIN_CFG_IOLH_QSPI		BIT(6)
-#define PIN_CFG_IOLH_ETH0		BIT(7)
-#define PIN_CFG_IOLH_ETH1		BIT(8)
+#define PIN_CFG_IO_VMC_SD0		BIT(4)
+#define PIN_CFG_IO_VMC_SD1		BIT(5)
+#define PIN_CFG_IO_VMC_QSPI		BIT(6)
+#define PIN_CFG_IO_VMC_ETH0		BIT(7)
+#define PIN_CFG_IO_VMC_ETH1		BIT(8)
 #define PIN_CFG_FILONOFF		BIT(9)
 #define PIN_CFG_FILNUM			BIT(10)
 #define PIN_CFG_FILCLKSEL		BIT(11)
@@ -533,11 +533,11 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
 	case PIN_CONFIG_POWER_SOURCE: {
 		u32 pwr_reg = 0x0;
 
-		if (cfg & PIN_CFG_IOLH_SD0)
+		if (cfg & PIN_CFG_IO_VMC_SD0)
 			pwr_reg = SD_CH(0);
-		else if (cfg & PIN_CFG_IOLH_SD1)
+		else if (cfg & PIN_CFG_IO_VMC_SD1)
 			pwr_reg = SD_CH(1);
-		else if (cfg & PIN_CFG_IOLH_QSPI)
+		else if (cfg & PIN_CFG_IO_VMC_QSPI)
 			pwr_reg = QSPI;
 		else
 			return -EINVAL;
@@ -612,11 +612,11 @@ static int rzg2l_pinctrl_pinconf_set(struct pinctrl_dev *pctldev,
 			if (mV != 1800 && mV != 3300)
 				return -EINVAL;
 
-			if (cfg & PIN_CFG_IOLH_SD0)
+			if (cfg & PIN_CFG_IO_VMC_SD0)
 				pwr_reg = SD_CH(0);
-			else if (cfg & PIN_CFG_IOLH_SD1)
+			else if (cfg & PIN_CFG_IO_VMC_SD1)
 				pwr_reg = SD_CH(1);
-			else if (cfg & PIN_CFG_IOLH_QSPI)
+			else if (cfg & PIN_CFG_IO_VMC_QSPI)
 				pwr_reg = QSPI;
 			else
 				return -EINVAL;
@@ -918,24 +918,24 @@ static const u32 rzg2l_gpio_configs[] = {
 	RZG2L_GPIO_PORT_PACK(3, 0x21, RZG2L_MPXED_PIN_FUNCS),
 	RZG2L_GPIO_PORT_PACK(2, 0x22, RZG2L_MPXED_PIN_FUNCS),
 	RZG2L_GPIO_PORT_PACK(2, 0x23, RZG2L_MPXED_PIN_FUNCS),
-	RZG2L_GPIO_PORT_PACK(3, 0x24, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IOLH_ETH0)),
-	RZG2L_GPIO_PORT_PACK(2, 0x25, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IOLH_ETH0)),
-	RZG2L_GPIO_PORT_PACK(2, 0x26, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IOLH_ETH0)),
-	RZG2L_GPIO_PORT_PACK(2, 0x27, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IOLH_ETH0)),
-	RZG2L_GPIO_PORT_PACK(2, 0x28, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IOLH_ETH0)),
-	RZG2L_GPIO_PORT_PACK(2, 0x29, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IOLH_ETH0)),
-	RZG2L_GPIO_PORT_PACK(2, 0x2a, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IOLH_ETH0)),
-	RZG2L_GPIO_PORT_PACK(2, 0x2b, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IOLH_ETH0)),
-	RZG2L_GPIO_PORT_PACK(2, 0x2c, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IOLH_ETH0)),
-	RZG2L_GPIO_PORT_PACK(2, 0x2d, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IOLH_ETH1)),
-	RZG2L_GPIO_PORT_PACK(2, 0x2e, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IOLH_ETH1)),
-	RZG2L_GPIO_PORT_PACK(2, 0x2f, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IOLH_ETH1)),
-	RZG2L_GPIO_PORT_PACK(2, 0x30, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IOLH_ETH1)),
-	RZG2L_GPIO_PORT_PACK(2, 0x31, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IOLH_ETH1)),
-	RZG2L_GPIO_PORT_PACK(2, 0x32, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IOLH_ETH1)),
-	RZG2L_GPIO_PORT_PACK(2, 0x33, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IOLH_ETH1)),
-	RZG2L_GPIO_PORT_PACK(2, 0x34, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IOLH_ETH1)),
-	RZG2L_GPIO_PORT_PACK(3, 0x35, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IOLH_ETH1)),
+	RZG2L_GPIO_PORT_PACK(3, 0x24, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IO_VMC_ETH0)),
+	RZG2L_GPIO_PORT_PACK(2, 0x25, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IO_VMC_ETH0)),
+	RZG2L_GPIO_PORT_PACK(2, 0x26, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IO_VMC_ETH0)),
+	RZG2L_GPIO_PORT_PACK(2, 0x27, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IO_VMC_ETH0)),
+	RZG2L_GPIO_PORT_PACK(2, 0x28, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IO_VMC_ETH0)),
+	RZG2L_GPIO_PORT_PACK(2, 0x29, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IO_VMC_ETH0)),
+	RZG2L_GPIO_PORT_PACK(2, 0x2a, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IO_VMC_ETH0)),
+	RZG2L_GPIO_PORT_PACK(2, 0x2b, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IO_VMC_ETH0)),
+	RZG2L_GPIO_PORT_PACK(2, 0x2c, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IO_VMC_ETH0)),
+	RZG2L_GPIO_PORT_PACK(2, 0x2d, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IO_VMC_ETH1)),
+	RZG2L_GPIO_PORT_PACK(2, 0x2e, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IO_VMC_ETH1)),
+	RZG2L_GPIO_PORT_PACK(2, 0x2f, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IO_VMC_ETH1)),
+	RZG2L_GPIO_PORT_PACK(2, 0x30, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IO_VMC_ETH1)),
+	RZG2L_GPIO_PORT_PACK(2, 0x31, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IO_VMC_ETH1)),
+	RZG2L_GPIO_PORT_PACK(2, 0x32, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IO_VMC_ETH1)),
+	RZG2L_GPIO_PORT_PACK(2, 0x33, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IO_VMC_ETH1)),
+	RZG2L_GPIO_PORT_PACK(2, 0x34, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IO_VMC_ETH1)),
+	RZG2L_GPIO_PORT_PACK(3, 0x35, RZG2L_MPXED_ETH_PIN_FUNCS(PIN_CFG_IO_VMC_ETH1)),
 	RZG2L_GPIO_PORT_PACK(2, 0x36, RZG2L_MPXED_PIN_FUNCS),
 	RZG2L_GPIO_PORT_PACK(3, 0x37, RZG2L_MPXED_PIN_FUNCS),
 	RZG2L_GPIO_PORT_PACK(3, 0x38, RZG2L_MPXED_PIN_FUNCS),
@@ -959,68 +959,68 @@ static  struct rzg2l_dedicated_configs rzg2l_dedicated_pins[] = {
 	{ "AUDIO_CLK1", RZG2L_SINGLE_PIN_PACK(0x4, 0, PIN_CFG_IEN) },
 	{ "AUDIO_CLK2", RZG2L_SINGLE_PIN_PACK(0x4, 1, PIN_CFG_IEN) },
 	{ "SD0_CLK", RZG2L_SINGLE_PIN_PACK(0x6, 0,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IOLH_SD0)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_CMD", RZG2L_SINGLE_PIN_PACK(0x6, 1,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IOLH_SD0)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_RST#", RZG2L_SINGLE_PIN_PACK(0x6, 2,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IOLH_SD0)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_DATA0", RZG2L_SINGLE_PIN_PACK(0x7, 0,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IOLH_SD0)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_DATA1", RZG2L_SINGLE_PIN_PACK(0x7, 1,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IOLH_SD0)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_DATA2", RZG2L_SINGLE_PIN_PACK(0x7, 2,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IOLH_SD0)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_DATA3", RZG2L_SINGLE_PIN_PACK(0x7, 3,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IOLH_SD0)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_DATA4", RZG2L_SINGLE_PIN_PACK(0x7, 4,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IOLH_SD0)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_DATA5", RZG2L_SINGLE_PIN_PACK(0x7, 5,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IOLH_SD0)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_DATA6", RZG2L_SINGLE_PIN_PACK(0x7, 6,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IOLH_SD0)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_DATA7", RZG2L_SINGLE_PIN_PACK(0x7, 7,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IOLH_SD0)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD1_CLK", RZG2L_SINGLE_PIN_PACK(0x8, 0,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IOLH_SD1))},
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_SD1))},
 	{ "SD1_CMD", RZG2L_SINGLE_PIN_PACK(0x8, 1,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IOLH_SD1)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD1)) },
 	{ "SD1_DATA0", RZG2L_SINGLE_PIN_PACK(0x9, 0,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IOLH_SD1)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD1)) },
 	{ "SD1_DATA1", RZG2L_SINGLE_PIN_PACK(0x9, 1,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IOLH_SD1)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD1)) },
 	{ "SD1_DATA2", RZG2L_SINGLE_PIN_PACK(0x9, 2,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IOLH_SD1)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD1)) },
 	{ "SD1_DATA3", RZG2L_SINGLE_PIN_PACK(0x9, 3,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IOLH_SD1)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD1)) },
 	{ "QSPI0_SPCLK", RZG2L_SINGLE_PIN_PACK(0xa, 0,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IOLH_QSPI)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI0_IO0", RZG2L_SINGLE_PIN_PACK(0xa, 1,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IOLH_QSPI)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI0_IO1", RZG2L_SINGLE_PIN_PACK(0xa, 2,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IOLH_QSPI)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI0_IO2", RZG2L_SINGLE_PIN_PACK(0xa, 3,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IOLH_QSPI)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI0_IO3", RZG2L_SINGLE_PIN_PACK(0xa, 4,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IOLH_QSPI)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI0_SSL", RZG2L_SINGLE_PIN_PACK(0xa, 5,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IOLH_QSPI)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI1_SPCLK", RZG2L_SINGLE_PIN_PACK(0xb, 0,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IOLH_QSPI)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI1_IO0", RZG2L_SINGLE_PIN_PACK(0xb, 1,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IOLH_QSPI)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI1_IO1", RZG2L_SINGLE_PIN_PACK(0xb, 2,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IOLH_QSPI)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI1_IO2", RZG2L_SINGLE_PIN_PACK(0xb, 3,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IOLH_QSPI)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI1_IO3", RZG2L_SINGLE_PIN_PACK(0xb, 4,
-	 (PIN_CFG_IOLH | PIN_CFG_SR  | PIN_CFG_IOLH_QSPI)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR  | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI1_SSL", RZG2L_SINGLE_PIN_PACK(0xb, 5,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IOLH_QSPI)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI_RESET#", RZG2L_SINGLE_PIN_PACK(0xc, 0,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IOLH_QSPI)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI_WP#", RZG2L_SINGLE_PIN_PACK(0xc, 1,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IOLH_QSPI)) },
-	{ "QSPI_INT#", RZG2L_SINGLE_PIN_PACK(0xc, 2, (PIN_CFG_SR | PIN_CFG_IOLH_QSPI)) },
+	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
+	{ "QSPI_INT#", RZG2L_SINGLE_PIN_PACK(0xc, 2, (PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "WDTOVF_PERROUT#", RZG2L_SINGLE_PIN_PACK(0xd, 0, (PIN_CFG_IOLH | PIN_CFG_SR)) },
 	{ "RIIC0_SDA", RZG2L_SINGLE_PIN_PACK(0xe, 0, PIN_CFG_IEN) },
 	{ "RIIC0_SCL", RZG2L_SINGLE_PIN_PACK(0xe, 1, PIN_CFG_IEN) },
-- 
2.17.1

Re: [PATCH v2 4/5] pinctrl: renesas: pinctrl-rzg2l: Rename PIN_CFG_* macros to match HW manual

[Geert Uytterhoeven]

On Fri, Oct 29, 2021 at 2:44 PM Lad Prabhakar
<prabhakar.mahadev-lad.rj@bp.renesas.com> wrote:
> Rename the below macros to match the HW manual (Rev.1.00):
> PIN_CFG_IOLH_SD0 -> PIN_CFG_IO_VMC_SD0
> PIN_CFG_IOLH_SD1 -> PIN_CFG_IO_VMC_SD1
> PIN_CFG_IOLH_QSPI -> PIN_CFG_IO_VMC_QSPI
> PIN_CFG_IOLH_ETH0 -> PIN_CFG_IO_VMC_ETH0
> PIN_CFG_IOLH_ETH1 -> PIN_CFG_IO_VMC_ETH1
>
> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>

Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
i.e. will queue in renesas-pinctrl-for-v5.17.

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

[PATCH v2 5/5] pinctrl: renesas: pinctrl-rzg2l: Add support to get/set drive-strength and output-impedance-ohms

[Lad Prabhakar]

RZ/G2L supports two groups of pins Group-A and Group-B. For Group-A
pins drive-strength can be configured and for Group-B output-impedance
can be configured.

This patch splits PIN_CFG_IOLH macro to PIN_CFG_IOLH_A/B and adds
support to get/set drive-strength and output-impedance-ohms for the
supported pins.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
---
 drivers/pinctrl/renesas/pinctrl-rzg2l.c | 159 ++++++++++++++++--------
 1 file changed, 110 insertions(+), 49 deletions(-)

diff --git a/drivers/pinctrl/renesas/pinctrl-rzg2l.c b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
index 348fc8dd74e6..f02d76c4966b 100644
--- a/drivers/pinctrl/renesas/pinctrl-rzg2l.c
+++ b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
@@ -35,20 +35,21 @@
 #define MUX_FUNC(pinconf)	(((pinconf) & MUX_FUNC_MASK) >> MUX_FUNC_OFFS)
 
 /* PIN capabilities */
-#define PIN_CFG_IOLH			BIT(0)
-#define PIN_CFG_SR			BIT(1)
-#define PIN_CFG_IEN			BIT(2)
-#define PIN_CFG_PUPD			BIT(3)
-#define PIN_CFG_IO_VMC_SD0		BIT(4)
-#define PIN_CFG_IO_VMC_SD1		BIT(5)
-#define PIN_CFG_IO_VMC_QSPI		BIT(6)
-#define PIN_CFG_IO_VMC_ETH0		BIT(7)
-#define PIN_CFG_IO_VMC_ETH1		BIT(8)
-#define PIN_CFG_FILONOFF		BIT(9)
-#define PIN_CFG_FILNUM			BIT(10)
-#define PIN_CFG_FILCLKSEL		BIT(11)
-
-#define RZG2L_MPXED_PIN_FUNCS		(PIN_CFG_IOLH | \
+#define PIN_CFG_IOLH_A			BIT(0)
+#define PIN_CFG_IOLH_B			BIT(1)
+#define PIN_CFG_SR			BIT(2)
+#define PIN_CFG_IEN			BIT(3)
+#define PIN_CFG_PUPD			BIT(4)
+#define PIN_CFG_IO_VMC_SD0		BIT(5)
+#define PIN_CFG_IO_VMC_SD1		BIT(6)
+#define PIN_CFG_IO_VMC_QSPI		BIT(7)
+#define PIN_CFG_IO_VMC_ETH0		BIT(8)
+#define PIN_CFG_IO_VMC_ETH1		BIT(9)
+#define PIN_CFG_FILONOFF		BIT(10)
+#define PIN_CFG_FILNUM			BIT(11)
+#define PIN_CFG_FILCLKSEL		BIT(12)
+
+#define RZG2L_MPXED_PIN_FUNCS		(PIN_CFG_IOLH_A | \
 					 PIN_CFG_SR | \
 					 PIN_CFG_PUPD | \
 					 PIN_CFG_FILONOFF | \
@@ -86,6 +87,7 @@
 #define PMC(n)			(0x0200 + 0x10 + (n))
 #define PFC(n)			(0x0400 + 0x40 + (n) * 4)
 #define PIN(n)			(0x0800 + 0x10 + (n))
+#define IOLH(n)			(0x1010 + (n) * 8 - 0x10)
 #define IEN(n)			(0x1800 + (n) * 8)
 #define PWPR			(0x3014)
 #define SD_CH(n)		(0x3000 + (n) * 4)
@@ -103,6 +105,7 @@
 #define PVDD_MASK		0x01
 #define PFC_MASK		0x07
 #define IEN_MASK		0x01
+#define IOLH_MASK		0x03
 
 #define PM_INPUT		0x1
 #define PM_OUTPUT		0x2
@@ -139,6 +142,9 @@ struct rzg2l_pinctrl {
 	spinlock_t			lock;
 };
 
+static const unsigned int iolh_groupa_mA[] = { 2, 4, 8, 12 };
+static const unsigned int iolh_groupb_oi[] = { 100, 66, 50, 33 };
+
 static void rzg2l_pinctrl_set_pfc_mode(struct rzg2l_pinctrl *pctrl,
 				       u8 port, u8 pin, u8 func)
 {
@@ -501,7 +507,7 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
 	unsigned int arg = 0;
 	unsigned long flags;
 	void __iomem *addr;
-	u32 port = 0;
+	u32 port = 0, reg;
 	u32 cfg = 0;
 	u8 bit = 0;
 
@@ -549,6 +555,24 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
 		break;
 	}
 
+	case PIN_CONFIG_DRIVE_STRENGTH: {
+		if (!(cfg & PIN_CFG_IOLH_A))
+			return -EINVAL;
+
+		reg = rzg2l_read_pin_config(pctrl, port_pin, IOLH(port), bit, IOLH_MASK);
+		arg = iolh_groupa_mA[reg];
+		break;
+	}
+
+	case PIN_CONFIG_OUTPUT_IMPEDANCE_OHMS: {
+		if (!(cfg & PIN_CFG_IOLH_B))
+			return -EINVAL;
+
+		reg = rzg2l_read_pin_config(pctrl, port_pin, IOLH(port), bit, IOLH_MASK);
+		arg = iolh_groupb_oi[reg];
+		break;
+	}
+
 	default:
 		return -ENOTSUPP;
 	}
@@ -627,6 +651,43 @@ static int rzg2l_pinctrl_pinconf_set(struct pinctrl_dev *pctldev,
 			spin_unlock_irqrestore(&pctrl->lock, flags);
 			break;
 		}
+
+		case PIN_CONFIG_DRIVE_STRENGTH: {
+			unsigned int arg = pinconf_to_config_argument(_configs[i]);
+			unsigned int index;
+
+			if (!(cfg & PIN_CFG_IOLH_A))
+				return -EINVAL;
+
+			for (index = 0; index < ARRAY_SIZE(iolh_groupa_mA); index++) {
+				if (arg == iolh_groupa_mA[index])
+					break;
+			}
+			if (index >= ARRAY_SIZE(iolh_groupa_mA))
+				return -EINVAL;
+
+			rzg2l_rmw_pin_config(pctrl, port_pin, IOLH(port), bit, IOLH_MASK, index);
+			break;
+		}
+
+		case PIN_CONFIG_OUTPUT_IMPEDANCE_OHMS: {
+			unsigned int arg = pinconf_to_config_argument(_configs[i]);
+			unsigned int index;
+
+			if (!(cfg & PIN_CFG_IOLH_B))
+				return -EINVAL;
+
+			for (index = 0; index < ARRAY_SIZE(iolh_groupb_oi); index++) {
+				if (arg == iolh_groupb_oi[index])
+					break;
+			}
+			if (index >= ARRAY_SIZE(iolh_groupb_oi))
+				return -EINVAL;
+
+			rzg2l_rmw_pin_config(pctrl, port_pin, IOLH(port), bit, IOLH_MASK, index);
+			break;
+		}
+
 		default:
 			return -EOPNOTSUPP;
 		}
@@ -953,75 +1014,75 @@ static  struct rzg2l_dedicated_configs rzg2l_dedicated_pins[] = {
 	{ "NMI", RZG2L_SINGLE_PIN_PACK(0x1, 0,
 	 (PIN_CFG_FILONOFF | PIN_CFG_FILNUM | PIN_CFG_FILCLKSEL)) },
 	{ "TMS/SWDIO", RZG2L_SINGLE_PIN_PACK(0x2, 0,
-	 (PIN_CFG_SR | PIN_CFG_IOLH | PIN_CFG_IEN)) },
+	 (PIN_CFG_SR | PIN_CFG_IOLH_A | PIN_CFG_IEN)) },
 	{ "TDO", RZG2L_SINGLE_PIN_PACK(0x3, 0,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN)) },
+	 (PIN_CFG_IOLH_A | PIN_CFG_SR | PIN_CFG_IEN)) },
 	{ "AUDIO_CLK1", RZG2L_SINGLE_PIN_PACK(0x4, 0, PIN_CFG_IEN) },
 	{ "AUDIO_CLK2", RZG2L_SINGLE_PIN_PACK(0x4, 1, PIN_CFG_IEN) },
 	{ "SD0_CLK", RZG2L_SINGLE_PIN_PACK(0x6, 0,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_SD0)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_CMD", RZG2L_SINGLE_PIN_PACK(0x6, 1,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_RST#", RZG2L_SINGLE_PIN_PACK(0x6, 2,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_SD0)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_DATA0", RZG2L_SINGLE_PIN_PACK(0x7, 0,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_DATA1", RZG2L_SINGLE_PIN_PACK(0x7, 1,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_DATA2", RZG2L_SINGLE_PIN_PACK(0x7, 2,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_DATA3", RZG2L_SINGLE_PIN_PACK(0x7, 3,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_DATA4", RZG2L_SINGLE_PIN_PACK(0x7, 4,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_DATA5", RZG2L_SINGLE_PIN_PACK(0x7, 5,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_DATA6", RZG2L_SINGLE_PIN_PACK(0x7, 6,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD0_DATA7", RZG2L_SINGLE_PIN_PACK(0x7, 7,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD0)) },
 	{ "SD1_CLK", RZG2L_SINGLE_PIN_PACK(0x8, 0,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_SD1))},
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IO_VMC_SD1)) },
 	{ "SD1_CMD", RZG2L_SINGLE_PIN_PACK(0x8, 1,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD1)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD1)) },
 	{ "SD1_DATA0", RZG2L_SINGLE_PIN_PACK(0x9, 0,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD1)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD1)) },
 	{ "SD1_DATA1", RZG2L_SINGLE_PIN_PACK(0x9, 1,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD1)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD1)) },
 	{ "SD1_DATA2", RZG2L_SINGLE_PIN_PACK(0x9, 2,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD1)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD1)) },
 	{ "SD1_DATA3", RZG2L_SINGLE_PIN_PACK(0x9, 3,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD1)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IEN | PIN_CFG_IO_VMC_SD1)) },
 	{ "QSPI0_SPCLK", RZG2L_SINGLE_PIN_PACK(0xa, 0,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI0_IO0", RZG2L_SINGLE_PIN_PACK(0xa, 1,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI0_IO1", RZG2L_SINGLE_PIN_PACK(0xa, 2,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI0_IO2", RZG2L_SINGLE_PIN_PACK(0xa, 3,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI0_IO3", RZG2L_SINGLE_PIN_PACK(0xa, 4,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI0_SSL", RZG2L_SINGLE_PIN_PACK(0xa, 5,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI1_SPCLK", RZG2L_SINGLE_PIN_PACK(0xb, 0,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI1_IO0", RZG2L_SINGLE_PIN_PACK(0xb, 1,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI1_IO1", RZG2L_SINGLE_PIN_PACK(0xb, 2,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI1_IO2", RZG2L_SINGLE_PIN_PACK(0xb, 3,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI1_IO3", RZG2L_SINGLE_PIN_PACK(0xb, 4,
-	 (PIN_CFG_IOLH | PIN_CFG_SR  | PIN_CFG_IO_VMC_QSPI)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR  | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI1_SSL", RZG2L_SINGLE_PIN_PACK(0xb, 5,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI_RESET#", RZG2L_SINGLE_PIN_PACK(0xc, 0,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI_WP#", RZG2L_SINGLE_PIN_PACK(0xc, 1,
-	 (PIN_CFG_IOLH | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
+	 (PIN_CFG_IOLH_B | PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
 	{ "QSPI_INT#", RZG2L_SINGLE_PIN_PACK(0xc, 2, (PIN_CFG_SR | PIN_CFG_IO_VMC_QSPI)) },
-	{ "WDTOVF_PERROUT#", RZG2L_SINGLE_PIN_PACK(0xd, 0, (PIN_CFG_IOLH | PIN_CFG_SR)) },
+	{ "WDTOVF_PERROUT#", RZG2L_SINGLE_PIN_PACK(0xd, 0, (PIN_CFG_IOLH_A | PIN_CFG_SR)) },
 	{ "RIIC0_SDA", RZG2L_SINGLE_PIN_PACK(0xe, 0, PIN_CFG_IEN) },
 	{ "RIIC0_SCL", RZG2L_SINGLE_PIN_PACK(0xe, 1, PIN_CFG_IEN) },
 	{ "RIIC1_SDA", RZG2L_SINGLE_PIN_PACK(0xe, 2, PIN_CFG_IEN) },
-- 
2.17.1

Re: [PATCH v2 5/5] pinctrl: renesas: pinctrl-rzg2l: Add support to get/set drive-strength and output-impedance-ohms

[Geert Uytterhoeven]

Hi Prabhakar,

On Fri, Oct 29, 2021 at 2:45 PM Lad Prabhakar
<prabhakar.mahadev-lad.rj@bp.renesas.com> wrote:
> RZ/G2L supports two groups of pins Group-A and Group-B. For Group-A
> pins drive-strength can be configured and for Group-B output-impedance
> can be configured.
>
> This patch splits PIN_CFG_IOLH macro to PIN_CFG_IOLH_A/B and adds
> support to get/set drive-strength and output-impedance-ohms for the
> supported pins.
>
> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>

Thanks for your patch!

> --- a/drivers/pinctrl/renesas/pinctrl-rzg2l.c
> +++ b/drivers/pinctrl/renesas/pinctrl-rzg2l.c

> @@ -501,7 +507,7 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
>         unsigned int arg = 0;
>         unsigned long flags;
>         void __iomem *addr;
> -       u32 port = 0;
> +       u32 port = 0, reg;

"unsigned int index", for symmetry with rzg2l_pinctrl_pinconf_set()?

>         u32 cfg = 0;
>         u8 bit = 0;
>
> @@ -549,6 +555,24 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
>                 break;
>         }
>
> +       case PIN_CONFIG_DRIVE_STRENGTH: {
> +               if (!(cfg & PIN_CFG_IOLH_A))
> +                       return -EINVAL;
> +
> +               reg = rzg2l_read_pin_config(pctrl, port_pin, IOLH(port), bit, IOLH_MASK);

port_pin still under discussion, cfr. my comments for the other
patches in this series.

The rest looks good to me, so
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

Re: [PATCH v2 5/5] pinctrl: renesas: pinctrl-rzg2l: Add support to get/set drive-strength and output-impedance-ohms

[Lad, Prabhakar]

Hi Geert,

Thank you for the review.

On Mon, Nov 8, 2021 at 3:40 PM Geert Uytterhoeven <geert@linux-m68k.org> wrote:
>
> Hi Prabhakar,
>
> On Fri, Oct 29, 2021 at 2:45 PM Lad Prabhakar
> <prabhakar.mahadev-lad.rj@bp.renesas.com> wrote:
> > RZ/G2L supports two groups of pins Group-A and Group-B. For Group-A
> > pins drive-strength can be configured and for Group-B output-impedance
> > can be configured.
> >
> > This patch splits PIN_CFG_IOLH macro to PIN_CFG_IOLH_A/B and adds
> > support to get/set drive-strength and output-impedance-ohms for the
> > supported pins.
> >
> > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> > Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
>
> Thanks for your patch!
>
> > --- a/drivers/pinctrl/renesas/pinctrl-rzg2l.c
> > +++ b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
>
> > @@ -501,7 +507,7 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
> >         unsigned int arg = 0;
> >         unsigned long flags;
> >         void __iomem *addr;
> > -       u32 port = 0;
> > +       u32 port = 0, reg;
>
> "unsigned int index", for symmetry with rzg2l_pinctrl_pinconf_set()?
>
Agreed.

> >         u32 cfg = 0;
> >         u8 bit = 0;
> >
> > @@ -549,6 +555,24 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
> >                 break;
> >         }
> >
> > +       case PIN_CONFIG_DRIVE_STRENGTH: {
> > +               if (!(cfg & PIN_CFG_IOLH_A))
> > +                       return -EINVAL;
> > +
> > +               reg = rzg2l_read_pin_config(pctrl, port_pin, IOLH(port), bit, IOLH_MASK);
>
> port_pin still under discussion, cfr. my comments for the other
> patches in this series.
>
As discussed in patch 3/5 will drop this.

Cheers,
Prabhakar

> The rest looks good to me, so
> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
>
> Gr{oetje,eeting}s,
>
>                         Geert
>
> --
> Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
>
> In personal conversations with technical people, I call myself a hacker. But
> when I'm talking to journalists I just say "programmer" or something like that.
>                                 -- Linus Torvalds