* [PATCH] mmc: davinci_mmc: Cleanup to use dt in U-boot and static platdata in SPL
@ 2020-05-22 2:02 Faiz Abbas
2020-05-25 12:03 ` Bartosz Golaszewski
` (2 more replies)
0 siblings, 3 replies; 9+ messages in thread
From: Faiz Abbas @ 2020-05-22 2:02 UTC (permalink / raw)
To: u-boot
Cleanup this driver to use dt in U-boot and static platdata in SPL.
This requires the following steps:
1. Move all platdata assignment from probe() to ofdata_to_platdata().
This function is only called in U-boot.
2. Replicate all the platdata assignment being done in
ofdata_to_platdata() in the omapl138 board file. This data is used in
the SPL case where SPL_OF_CONTROL is not enabled.
3. Remove SPL_OF_CONTROL and related configs from omapl138_lcdk_defconfig
This cleanup effectively reverts 3ef94715cc ('mmc: davinci: fix mmc boot in SPL')
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
---
This patch fixes things being broken by Simon's series disabling
libfdt when using of-platdata:
https://patchwork.ozlabs.org/project/uboot/cover/20191107155318.103300-1-sjg at chromium.org/
.../mach-davinci/include/mach/sdmmc_defs.h | 7 +++
board/davinci/da8xxevm/omapl138_lcdk.c | 12 ++++
configs/omapl138_lcdk_defconfig | 4 --
drivers/mmc/davinci_mmc.c | 63 ++++++++-----------
4 files changed, 45 insertions(+), 41 deletions(-)
diff --git a/arch/arm/mach-davinci/include/mach/sdmmc_defs.h b/arch/arm/mach-davinci/include/mach/sdmmc_defs.h
index 46f6391aa2..f95a607e52 100644
--- a/arch/arm/mach-davinci/include/mach/sdmmc_defs.h
+++ b/arch/arm/mach-davinci/include/mach/sdmmc_defs.h
@@ -152,6 +152,13 @@ struct davinci_mmc {
struct mmc_config cfg;
};
+#define DAVINCI_MAX_BLOCKS (32)
+struct davinci_mmc_plat {
+ struct davinci_mmc_regs *reg_base; /* Register base address */
+ struct mmc_config cfg;
+ struct mmc mmc;
+};
+
int davinci_mmc_init(bd_t *bis, struct davinci_mmc *host);
#endif /* _SDMMC_DEFS_H */
diff --git a/board/davinci/da8xxevm/omapl138_lcdk.c b/board/davinci/da8xxevm/omapl138_lcdk.c
index adb56c6c87..84603cb117 100644
--- a/board/davinci/da8xxevm/omapl138_lcdk.c
+++ b/board/davinci/da8xxevm/omapl138_lcdk.c
@@ -368,8 +368,20 @@ U_BOOT_DEVICE(omapl138_uart) = {
.platdata = &serial_pdata,
};
+static const struct davinci_mmc_plat mmc_platdata = {
+ .reg_base = (struct davinci_mmc_regs *)DAVINCI_MMC_SD0_BASE,
+ .cfg = {
+ .f_min = 200000,
+ .f_max = 25000000,
+ .voltages = MMC_VDD_32_33 | MMC_VDD_33_34,
+ .host_caps = MMC_MODE_4BIT,
+ .b_max = DAVINCI_MAX_BLOCKS,
+ .name = "da830-mmc",
+ },
+};
U_BOOT_DEVICE(omapl138_mmc) = {
.name = "davinci_mmc",
+ .platdata = &mmc_platdata,
};
void spl_board_init(void)
diff --git a/configs/omapl138_lcdk_defconfig b/configs/omapl138_lcdk_defconfig
index 50cf09c7f1..b0a58de03d 100644
--- a/configs/omapl138_lcdk_defconfig
+++ b/configs/omapl138_lcdk_defconfig
@@ -40,16 +40,13 @@ CONFIG_CMD_MTDPARTS=y
CONFIG_CMD_DIAG=y
CONFIG_CMD_UBI=y
CONFIG_OF_CONTROL=y
-CONFIG_SPL_OF_CONTROL=y
CONFIG_DEFAULT_DEVICE_TREE="da850-lcdk"
-CONFIG_SPL_OF_PLATDATA=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_SPL_DM=y
CONFIG_SPL_DM_SEQ_ALIAS=y
-CONFIG_SPL_OF_TRANSLATE=y
CONFIG_DA8XX_GPIO=y
CONFIG_DM_I2C=y
CONFIG_SYS_I2C_DAVINCI=y
@@ -82,4 +79,3 @@ CONFIG_USB_MUSB_HOST=y
CONFIG_USB_MUSB_DA8XX=y
CONFIG_USB_MUSB_PIO_ONLY=y
CONFIG_USB_STORAGE=y
-# CONFIG_SPL_OF_LIBFDT is not set
diff --git a/drivers/mmc/davinci_mmc.c b/drivers/mmc/davinci_mmc.c
index 2408a687d2..4ef9f7cc8b 100644
--- a/drivers/mmc/davinci_mmc.c
+++ b/drivers/mmc/davinci_mmc.c
@@ -18,7 +18,6 @@
#include <asm-generic/gpio.h>
#include <linux/delay.h>
-#define DAVINCI_MAX_BLOCKS (32)
#define WATCHDOG_COUNT (100000)
#define get_val(addr) REG(addr)
@@ -34,12 +33,6 @@ struct davinci_mmc_priv {
struct gpio_desc cd_gpio; /* Card Detect GPIO */
struct gpio_desc wp_gpio; /* Write Protect GPIO */
};
-
-struct davinci_mmc_plat
-{
- struct mmc_config cfg;
- struct mmc mmc;
-};
#endif
/* Set davinci clock prescalar value based on the required clock in HZ */
@@ -487,43 +480,16 @@ static int davinci_mmc_probe(struct udevice *dev)
struct mmc_uclass_priv *upriv = dev_get_uclass_priv(dev);
struct davinci_mmc_plat *plat = dev_get_platdata(dev);
struct davinci_mmc_priv *priv = dev_get_priv(dev);
- struct mmc_config *cfg = &plat->cfg;
-#ifdef CONFIG_SPL_BUILD
- int ret;
-#endif
-
- cfg->f_min = 200000;
- cfg->f_max = 25000000;
- cfg->voltages = MMC_VDD_32_33 | MMC_VDD_33_34,
- cfg->host_caps = MMC_MODE_4BIT, /* DA850 supports only 4-bit SD/MMC */
- cfg->b_max = DAVINCI_MAX_BLOCKS;
- cfg->name = "da830-mmc";
- priv->reg_base = (struct davinci_mmc_regs *)dev_read_addr(dev);
+ priv->reg_base = plat->reg_base;
priv->input_clk = clk_get(DAVINCI_MMCSD_CLKID);
-
#if CONFIG_IS_ENABLED(DM_GPIO)
/* These GPIOs are optional */
gpio_request_by_name(dev, "cd-gpios", 0, &priv->cd_gpio, GPIOD_IS_IN);
gpio_request_by_name(dev, "wp-gpios", 0, &priv->wp_gpio, GPIOD_IS_IN);
#endif
-
upriv->mmc = &plat->mmc;
-#ifdef CONFIG_SPL_BUILD
- /*
- * FIXME This is a temporary workaround to enable the driver model in
- * SPL on omapl138-lcdk. For some reason the bind() callback is not
- * being called in SPL for MMC which breaks the mmc boot - the hack
- * is to call mmc_bind() from probe(). We also don't have full DT
- * support in SPL, hence the hard-coded base register address.
- */
- priv->reg_base = (struct davinci_mmc_regs *)DAVINCI_MMC_SD0_BASE;
- ret = mmc_bind(dev, &plat->mmc, &plat->cfg);
- if (ret)
- return ret;
-#endif
-
return davinci_dm_mmc_init(dev);
}
@@ -534,21 +500,44 @@ static int davinci_mmc_bind(struct udevice *dev)
return mmc_bind(dev, &plat->mmc, &plat->cfg);
}
+#if CONFIG_IS_ENABLED(OF_CONTROL)
+static int davinci_mmc_ofdata_to_platdata(struct udevice *dev)
+{
+ struct davinci_mmc_plat *plat = dev_get_platdata(dev);
+ struct mmc_config *cfg = &plat->cfg;
+
+ plat->reg_base = (struct davinci_mmc_regs *)dev_read_addr(dev);
+ cfg->f_min = 200000;
+ cfg->f_max = 25000000;
+ cfg->voltages = MMC_VDD_32_33 | MMC_VDD_33_34,
+ cfg->host_caps = MMC_MODE_4BIT, /* DA850 supports only 4-bit SD/MMC */
+ cfg->b_max = DAVINCI_MAX_BLOCKS;
+ cfg->name = "da830-mmc";
+
+ return 0;
+}
+
static const struct udevice_id davinci_mmc_ids[] = {
{ .compatible = "ti,da830-mmc" },
{},
};
-
+#endif
U_BOOT_DRIVER(davinci_mmc_drv) = {
.name = "davinci_mmc",
.id = UCLASS_MMC,
+#if CONFIG_IS_ENABLED(OF_CONTROL)
.of_match = davinci_mmc_ids,
+ .platdata_auto_alloc_size = sizeof(struct davinci_mmc_plat),
+ .ofdata_to_platdata = davinci_mmc_ofdata_to_platdata,
+#endif
#if CONFIG_BLK
.bind = davinci_mmc_bind,
#endif
.probe = davinci_mmc_probe,
.ops = &davinci_mmc_ops,
- .platdata_auto_alloc_size = sizeof(struct davinci_mmc_plat),
.priv_auto_alloc_size = sizeof(struct davinci_mmc_priv),
+#if !CONFIG_IS_ENABLED(OF_CONTROL)
+ .flags = DM_FLAG_PRE_RELOC,
+#endif
};
#endif
--
2.17.1
^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH] mmc: davinci_mmc: Cleanup to use dt in U-boot and static platdata in SPL
2020-05-22 2:02 [PATCH] mmc: davinci_mmc: Cleanup to use dt in U-boot and static platdata in SPL Faiz Abbas
@ 2020-05-25 12:03 ` Bartosz Golaszewski
2020-05-25 14:57 ` Simon Glass
2020-06-18 13:54 ` Lokesh Vutla
2 siblings, 0 replies; 9+ messages in thread
From: Bartosz Golaszewski @ 2020-05-25 12:03 UTC (permalink / raw)
To: u-boot
pt., 22 maj 2020 o 04:02 Faiz Abbas <faiz_abbas@ti.com> napisa?(a):
>
> Cleanup this driver to use dt in U-boot and static platdata in SPL.
> This requires the following steps:
>
> 1. Move all platdata assignment from probe() to ofdata_to_platdata().
> This function is only called in U-boot.
> 2. Replicate all the platdata assignment being done in
> ofdata_to_platdata() in the omapl138 board file. This data is used in
> the SPL case where SPL_OF_CONTROL is not enabled.
> 3. Remove SPL_OF_CONTROL and related configs from omapl138_lcdk_defconfig
>
> This cleanup effectively reverts 3ef94715cc ('mmc: davinci: fix mmc boot in SPL')
>
> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH] mmc: davinci_mmc: Cleanup to use dt in U-boot and static platdata in SPL
2020-05-22 2:02 [PATCH] mmc: davinci_mmc: Cleanup to use dt in U-boot and static platdata in SPL Faiz Abbas
2020-05-25 12:03 ` Bartosz Golaszewski
@ 2020-05-25 14:57 ` Simon Glass
2020-05-25 15:33 ` Faiz Abbas
2020-06-18 13:54 ` Lokesh Vutla
2 siblings, 1 reply; 9+ messages in thread
From: Simon Glass @ 2020-05-25 14:57 UTC (permalink / raw)
To: u-boot
Hi Faiz,
On Thu, 21 May 2020 at 20:02, Faiz Abbas <faiz_abbas@ti.com> wrote:
>
> Cleanup this driver to use dt in U-boot and static platdata in SPL.
> This requires the following steps:
>
> 1. Move all platdata assignment from probe() to ofdata_to_platdata().
> This function is only called in U-boot.
> 2. Replicate all the platdata assignment being done in
> ofdata_to_platdata() in the omapl138 board file. This data is used in
> the SPL case where SPL_OF_CONTROL is not enabled.
> 3. Remove SPL_OF_CONTROL and related configs from omapl138_lcdk_defconfig
>
> This cleanup effectively reverts 3ef94715cc ('mmc: davinci: fix mmc boot in SPL')
>
> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
> ---
>
> This patch fixes things being broken by Simon's series disabling
> libfdt when using of-platdata:
> https://patchwork.ozlabs.org/project/uboot/cover/20191107155318.103300-1-sjg at chromium.org/
>
>
> .../mach-davinci/include/mach/sdmmc_defs.h | 7 +++
> board/davinci/da8xxevm/omapl138_lcdk.c | 12 ++++
> configs/omapl138_lcdk_defconfig | 4 --
> drivers/mmc/davinci_mmc.c | 63 ++++++++-----------
> 4 files changed, 45 insertions(+), 41 deletions(-)
Could this use of-platdata instead?
Regards,
Simon
^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH] mmc: davinci_mmc: Cleanup to use dt in U-boot and static platdata in SPL
2020-05-25 14:57 ` Simon Glass
@ 2020-05-25 15:33 ` Faiz Abbas
2020-05-25 15:38 ` Simon Glass
0 siblings, 1 reply; 9+ messages in thread
From: Faiz Abbas @ 2020-05-25 15:33 UTC (permalink / raw)
To: u-boot
Hi Simon,
On 25/05/20 8:27 pm, Simon Glass wrote:
> Hi Faiz,
>
> On Thu, 21 May 2020 at 20:02, Faiz Abbas <faiz_abbas@ti.com> wrote:
>>
>> Cleanup this driver to use dt in U-boot and static platdata in SPL.
>> This requires the following steps:
>>
>> 1. Move all platdata assignment from probe() to ofdata_to_platdata().
>> This function is only called in U-boot.
>> 2. Replicate all the platdata assignment being done in
>> ofdata_to_platdata() in the omapl138 board file. This data is used in
>> the SPL case where SPL_OF_CONTROL is not enabled.
>> 3. Remove SPL_OF_CONTROL and related configs from omapl138_lcdk_defconfig
>>
>> This cleanup effectively reverts 3ef94715cc ('mmc: davinci: fix mmc boot in SPL')
>>
>> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
>> ---
>>
>> This patch fixes things being broken by Simon's series disabling
>> libfdt when using of-platdata:
>> https://patchwork.ozlabs.org/project/uboot/cover/20191107155318.103300-1-sjg at chromium.org/
>>
>>
>> .../mach-davinci/include/mach/sdmmc_defs.h | 7 +++
>> board/davinci/da8xxevm/omapl138_lcdk.c | 12 ++++
>> configs/omapl138_lcdk_defconfig | 4 --
>> drivers/mmc/davinci_mmc.c | 63 ++++++++-----------
>> 4 files changed, 45 insertions(+), 41 deletions(-)
>
> Could this use of-platdata instead?
>
We would need to implement address translation in of-platdata to do that. I prefer merging your
fixes with this for now and leave of-platdata up for the future.
Thanks,
Faiz
^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH] mmc: davinci_mmc: Cleanup to use dt in U-boot and static platdata in SPL
2020-05-25 15:33 ` Faiz Abbas
@ 2020-05-25 15:38 ` Simon Glass
2020-05-26 16:54 ` Simon Glass
0 siblings, 1 reply; 9+ messages in thread
From: Simon Glass @ 2020-05-25 15:38 UTC (permalink / raw)
To: u-boot
Hi Faiz,
On Mon, 25 May 2020 at 09:33, Faiz Abbas <faiz_abbas@ti.com> wrote:
>
> Hi Simon,
>
> On 25/05/20 8:27 pm, Simon Glass wrote:
> > Hi Faiz,
> >
> > On Thu, 21 May 2020 at 20:02, Faiz Abbas <faiz_abbas@ti.com> wrote:
> >>
> >> Cleanup this driver to use dt in U-boot and static platdata in SPL.
> >> This requires the following steps:
> >>
> >> 1. Move all platdata assignment from probe() to ofdata_to_platdata().
> >> This function is only called in U-boot.
> >> 2. Replicate all the platdata assignment being done in
> >> ofdata_to_platdata() in the omapl138 board file. This data is used in
> >> the SPL case where SPL_OF_CONTROL is not enabled.
> >> 3. Remove SPL_OF_CONTROL and related configs from omapl138_lcdk_defconfig
> >>
> >> This cleanup effectively reverts 3ef94715cc ('mmc: davinci: fix mmc boot in SPL')
> >>
> >> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
> >> ---
> >>
> >> This patch fixes things being broken by Simon's series disabling
> >> libfdt when using of-platdata:
> >> https://patchwork.ozlabs.org/project/uboot/cover/20191107155318.103300-1-sjg at chromium.org/
> >>
> >>
> >> .../mach-davinci/include/mach/sdmmc_defs.h | 7 +++
> >> board/davinci/da8xxevm/omapl138_lcdk.c | 12 ++++
> >> configs/omapl138_lcdk_defconfig | 4 --
> >> drivers/mmc/davinci_mmc.c | 63 ++++++++-----------
> >> 4 files changed, 45 insertions(+), 41 deletions(-)
> >
> > Could this use of-platdata instead?
> >
>
> We would need to implement address translation in of-platdata to do that. I prefer merging your
> fixes with this for now and leave of-platdata up for the future.
OK, yes, we can't wait for non-existent features.
There is a bit of a queue of functionality lining up for of-platdata at present.
Regards,
Simon
^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH] mmc: davinci_mmc: Cleanup to use dt in U-boot and static platdata in SPL
2020-05-25 15:38 ` Simon Glass
@ 2020-05-26 16:54 ` Simon Glass
2020-05-26 17:37 ` Faiz Abbas
0 siblings, 1 reply; 9+ messages in thread
From: Simon Glass @ 2020-05-26 16:54 UTC (permalink / raw)
To: u-boot
Hi Faiz,
I have ended up with an omap L138 lcdk board. Do you have instructions
on how to get it booting from uSD and how to create the card image? I
have tried various sources but nothing works so far. Also, are you
able to send me a test image I can 'dd' onto the board?
Regards,
Simon
On Mon, 25 May 2020 at 09:38, Simon Glass <sjg@chromium.org> wrote:
>
> Hi Faiz,
>
> On Mon, 25 May 2020 at 09:33, Faiz Abbas <faiz_abbas@ti.com> wrote:
> >
> > Hi Simon,
> >
> > On 25/05/20 8:27 pm, Simon Glass wrote:
> > > Hi Faiz,
> > >
> > > On Thu, 21 May 2020 at 20:02, Faiz Abbas <faiz_abbas@ti.com> wrote:
> > >>
> > >> Cleanup this driver to use dt in U-boot and static platdata in SPL.
> > >> This requires the following steps:
> > >>
> > >> 1. Move all platdata assignment from probe() to ofdata_to_platdata().
> > >> This function is only called in U-boot.
> > >> 2. Replicate all the platdata assignment being done in
> > >> ofdata_to_platdata() in the omapl138 board file. This data is used in
> > >> the SPL case where SPL_OF_CONTROL is not enabled.
> > >> 3. Remove SPL_OF_CONTROL and related configs from omapl138_lcdk_defconfig
> > >>
> > >> This cleanup effectively reverts 3ef94715cc ('mmc: davinci: fix mmc boot in SPL')
> > >>
> > >> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
> > >> ---
> > >>
> > >> This patch fixes things being broken by Simon's series disabling
> > >> libfdt when using of-platdata:
> > >> https://patchwork.ozlabs.org/project/uboot/cover/20191107155318.103300-1-sjg at chromium.org/
> > >>
> > >>
> > >> .../mach-davinci/include/mach/sdmmc_defs.h | 7 +++
> > >> board/davinci/da8xxevm/omapl138_lcdk.c | 12 ++++
> > >> configs/omapl138_lcdk_defconfig | 4 --
> > >> drivers/mmc/davinci_mmc.c | 63 ++++++++-----------
> > >> 4 files changed, 45 insertions(+), 41 deletions(-)
> > >
> > > Could this use of-platdata instead?
> > >
> >
> > We would need to implement address translation in of-platdata to do that. I prefer merging your
> > fixes with this for now and leave of-platdata up for the future.
>
> OK, yes, we can't wait for non-existent features.
>
> There is a bit of a queue of functionality lining up for of-platdata at present.
>
> Regards,
> Simon
^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH] mmc: davinci_mmc: Cleanup to use dt in U-boot and static platdata in SPL
2020-05-26 16:54 ` Simon Glass
@ 2020-05-26 17:37 ` Faiz Abbas
2020-05-26 18:38 ` Simon Glass
0 siblings, 1 reply; 9+ messages in thread
From: Faiz Abbas @ 2020-05-26 17:37 UTC (permalink / raw)
To: u-boot
Simon,
On 26/05/20 10:24 pm, Simon Glass wrote:
> Hi Faiz,
>
> I have ended up with an omap L138 lcdk board. Do you have instructions
> on how to get it booting from uSD and how to create the card image? I
> have tried various sources but nothing works so far. Also, are you
> able to send me a test image I can 'dd' onto the board?
>
The commands in board/davinci/da8xxevm/README.da850 don't work?
Try the following:
2 - using the "dd" command
$ dd if=u-boot.ais of=/dev/mmcblk0 seek=117 bs=512 conv=fsync
Thanks,
Faiz
^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH] mmc: davinci_mmc: Cleanup to use dt in U-boot and static platdata in SPL
2020-05-26 17:37 ` Faiz Abbas
@ 2020-05-26 18:38 ` Simon Glass
0 siblings, 0 replies; 9+ messages in thread
From: Simon Glass @ 2020-05-26 18:38 UTC (permalink / raw)
To: u-boot
Hi Faiz,
On Tue, 26 May 2020 at 11:37, Faiz Abbas <faiz_abbas@ti.com> wrote:
>
> Simon,
>
> On 26/05/20 10:24 pm, Simon Glass wrote:
> > Hi Faiz,
> >
> > I have ended up with an omap L138 lcdk board. Do you have instructions
> > on how to get it booting from uSD and how to create the card image? I
> > have tried various sources but nothing works so far. Also, are you
> > able to send me a test image I can 'dd' onto the board?
> >
>
> The commands in board/davinci/da8xxevm/README.da850 don't work?
>
> Try the following:
>
> 2 - using the "dd" command
> $ dd if=u-boot.ais of=/dev/mmcblk0 seek=117 bs=512 conv=fsync
Thanks! I didn't make the connection with da850 or think to look in
board/ for docs.
Regards,
Simon
^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH] mmc: davinci_mmc: Cleanup to use dt in U-boot and static platdata in SPL
2020-05-22 2:02 [PATCH] mmc: davinci_mmc: Cleanup to use dt in U-boot and static platdata in SPL Faiz Abbas
2020-05-25 12:03 ` Bartosz Golaszewski
2020-05-25 14:57 ` Simon Glass
@ 2020-06-18 13:54 ` Lokesh Vutla
2 siblings, 0 replies; 9+ messages in thread
From: Lokesh Vutla @ 2020-06-18 13:54 UTC (permalink / raw)
To: u-boot
On 22/05/20 7:32 am, Faiz Abbas wrote:
> Cleanup this driver to use dt in U-boot and static platdata in SPL.
> This requires the following steps:
>
> 1. Move all platdata assignment from probe() to ofdata_to_platdata().
> This function is only called in U-boot.
> 2. Replicate all the platdata assignment being done in
> ofdata_to_platdata() in the omapl138 board file. This data is used in
> the SPL case where SPL_OF_CONTROL is not enabled.
> 3. Remove SPL_OF_CONTROL and related configs from omapl138_lcdk_defconfig
>
> This cleanup effectively reverts 3ef94715cc ('mmc: davinci: fix mmc boot in SPL')
>
> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Applied to u-boot-ti next.
Thanks and regards,
Lokesh
^ permalink raw reply [flat|nested] 9+ messages in thread
end of thread, other threads:[~2020-06-18 13:54 UTC | newest]
Thread overview: 9+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-05-22 2:02 [PATCH] mmc: davinci_mmc: Cleanup to use dt in U-boot and static platdata in SPL Faiz Abbas
2020-05-25 12:03 ` Bartosz Golaszewski
2020-05-25 14:57 ` Simon Glass
2020-05-25 15:33 ` Faiz Abbas
2020-05-25 15:38 ` Simon Glass
2020-05-26 16:54 ` Simon Glass
2020-05-26 17:37 ` Faiz Abbas
2020-05-26 18:38 ` Simon Glass
2020-06-18 13:54 ` Lokesh Vutla
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.