* [PATCH v7 00/22] RISC-V SiFive FU540 support SPL
@ 2020-05-02 10:06 Pragnesh Patel
2020-05-02 10:06 ` [PATCH v7 01/22] misc: add driver for the SiFive otp controller Pragnesh Patel
` (22 more replies)
0 siblings, 23 replies; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-02 10:06 UTC (permalink / raw)
To: u-boot
This series add support for SPL to FU540.U-Boot SPL can boot from
L2 LIM (0x0800_0000) and jump to OpenSBI(FW_DYNAMIC firmware) and
U-Boot proper from MMC devices.
How to test this patch:
1) Go to OpenSBI-dir : make PLATFORM=generic FW_DYNAMIC=y
2) export OPENSBI=<path/to/opensbi/install_dir/platform/generic/firmware/fw_dynamic.bin>
3) Change to u-boot-dir
4) make sifive_fu540_defconfig
5) make all
6) Format the SD card (make sure the disk has GPT, otherwise use gdisk to switch)
# sudo sgdisk --clear \
> --set-alignment=2 \
> --new=1:34:2081 --change-name=1:loader1 --typecode=1:5B193300-FC78-40CD-8002-E86C45580B47 \
> --new=2:2082:10273 --change-name=2:loader2 --typecode=2:2E54B353-1271-4842-806F-E436D6AF6985 \
> --new=3:10274: --change-name=3:rootfs --typecode=3:0FC63DAF-8483-4772-8E79-3D69D8477DE4 \
> /dev/sda
7) sudo dd if=spl/u-boot-spl.bin of=/dev/sda seek=34
8) sudo dd if=u-boot.itb of=/dev/sda seek=2082
Changes in v7:
- Standardize SD gpt partition layout
- Add delay for SiFive OTP driver
- Use DM way for corepll and ddrpll
- Add new cpu fu540 (arch/riscv/cpu/fu540)
- Update document for FU540 (doc/board/sifive/fu540.rst)
Changes in v6:
- Typo Correction
- Make fu540-c000-u-boot.dtsi and hifive-unleashed-a00-u-boot.dtsi
Dual Licensed
- Sync Hifive unleashed dts from Linux
- Add arch/riscv/fu540 for FU540 specific code
Changes in v5:
- Return read/write bytes for sifive_otp_read and sifive_otp_write
- Correct Palmer's email address
Changes in v4:
- Split misc DM driver patch into multiple patches
- Added new SPL_CRC7_SUPPORT Kconfig option
- Added DM driver for DDR
- Added clk_enable and clk_disable ops in SiFive PRCI driver
- Added early clock initialization for SPL in SiFive PRCI driver
- Added SPL config options in sifive_fu540_defconfig instead of
creatiing a new config file for SPL
- Update fu540.rst on how to build and flash U-boot SPL
Changes in v3:
- Remove arch-fu540 and arch-sifive from arch/riscv/include/asm/
- Split SPL patches into DDR and SPL and spl defconfig
- Update fu540/MAINTAINERS file
- Update fu540.rst on how to build and flash U-boot SPL
Changes in v2:
- Add DM driver Sifive OTP
- Split SPL patches into multiple patches
- Add a seprate patch for _image_binary_end and crc7.c
- Add a seprate patch to add board -u-boot.dtsi files
- Update FU540 RISC-V documentation
Pragnesh Patel (22):
misc: add driver for the SiFive otp controller
riscv: sifive: fu540: Use OTP DM driver for serial environment
variable
riscv: Add _image_binary_end for SPL
lib: Makefile: build crc7.c when CONFIG_MMC_SPI
riscv: sifive: dts: fu540: Add board -u-boot.dtsi files
sifive: fu540: add ddr driver
sifive: dts: fu540: Add DDR controller and phy register settings
riscv: sifive: dts: fu540: add U-Boot dmc node
clk: sifive: fu540-prci: Add clock enable and disable ops
clk: sifive: fu540-prci: ddr and ethernet clock initialization in SPL
riscv: dts: sifive: Sync hifive-unleashed-a00 dts from linux
sifive: dts: fu540: Enable gpio in U-Boot SPL
riscv: cpu: fu540: Add support for cpu fu540
riscv: Add place-holder for driver compilation
riscv: sifive: dts: fu540: Add clock for cpus node
riscv: Enable cpu clock if it is present
riscv: sifive: fu540: add SPL configuration
configs: fu540: Add config options for U-Boot SPL
sifive: dts: fu540: Enable L2 Cache in U-Boot
riscv: sifive: fu540: enable all cache ways from U-Boot proper
doc: sifive: fu540: Add description for OpenSBI generic platform
doc: sifive: fu540: Add description for RISC-V FU540 U-Boot SPL
arch/riscv/Kconfig | 1 +
arch/riscv/cpu/fu540/Kconfig | 15 +
arch/riscv/cpu/fu540/Makefile | 12 +
arch/riscv/cpu/fu540/cache.c | 53 +
arch/riscv/cpu/fu540/cpu.c | 22 +
arch/riscv/cpu/fu540/dram.c | 38 +
arch/riscv/cpu/fu540/spl.c | 23 +
arch/riscv/cpu/u-boot-spl.lds | 1 +
arch/riscv/dts/fu540-c000-u-boot.dtsi | 91 +
arch/riscv/dts/fu540-c000.dtsi | 37 +-
...fu540-hifive-unleashed-a00-sdram-ddr4.dtsi | 1489 +++++++++++++++++
.../dts/hifive-unleashed-a00-u-boot.dtsi | 22 +
arch/riscv/dts/hifive-unleashed-a00.dts | 9 +
arch/riscv/include/asm/arch-fu540/cache.h | 14 +
arch/riscv/include/asm/arch-fu540/clk.h | 14 +
arch/riscv/include/asm/arch-fu540/gpio.h | 38 +
arch/riscv/include/asm/arch-fu540/spl.h | 14 +
board/sifive/fu540/Kconfig | 14 +-
board/sifive/fu540/Makefile | 4 +
board/sifive/fu540/fu540.c | 143 +-
board/sifive/fu540/spl.c | 72 +
common/spl/Kconfig | 6 +
configs/sifive_fu540_defconfig | 9 +
doc/board/sifive/fu540.rst | 395 ++++-
drivers/clk/sifive/fu540-prci.c | 193 ++-
drivers/cpu/riscv_cpu.c | 33 +
drivers/misc/Kconfig | 7 +
drivers/misc/Makefile | 1 +
drivers/misc/sifive-otp.c | 273 +++
drivers/mmc/Kconfig | 1 +
drivers/ram/Kconfig | 1 +
drivers/ram/Makefile | 2 +
drivers/ram/sifive/Kconfig | 13 +
drivers/ram/sifive/Makefile | 6 +
drivers/ram/sifive/sdram_fu540.c | 416 +++++
include/configs/sifive-fu540.h | 18 +
lib/Makefile | 1 +
37 files changed, 3403 insertions(+), 98 deletions(-)
create mode 100644 arch/riscv/cpu/fu540/Kconfig
create mode 100644 arch/riscv/cpu/fu540/Makefile
create mode 100644 arch/riscv/cpu/fu540/cache.c
create mode 100644 arch/riscv/cpu/fu540/cpu.c
create mode 100644 arch/riscv/cpu/fu540/dram.c
create mode 100644 arch/riscv/cpu/fu540/spl.c
create mode 100644 arch/riscv/dts/fu540-c000-u-boot.dtsi
create mode 100644 arch/riscv/dts/fu540-hifive-unleashed-a00-sdram-ddr4.dtsi
create mode 100644 arch/riscv/include/asm/arch-fu540/cache.h
create mode 100644 arch/riscv/include/asm/arch-fu540/clk.h
create mode 100644 arch/riscv/include/asm/arch-fu540/gpio.h
create mode 100644 arch/riscv/include/asm/arch-fu540/spl.h
create mode 100644 board/sifive/fu540/spl.c
create mode 100644 drivers/misc/sifive-otp.c
create mode 100644 drivers/ram/sifive/Kconfig
create mode 100644 drivers/ram/sifive/Makefile
create mode 100644 drivers/ram/sifive/sdram_fu540.c
--
2.17.1
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 01/22] misc: add driver for the SiFive otp controller
2020-05-02 10:06 [PATCH v7 00/22] RISC-V SiFive FU540 support SPL Pragnesh Patel
@ 2020-05-02 10:06 ` Pragnesh Patel
2020-05-02 12:28 ` Bin Meng
2020-05-02 15:37 ` Jagan Teki
2020-05-02 10:06 ` [PATCH v7 02/22] riscv: sifive: fu540: Use OTP DM driver for serial environment variable Pragnesh Patel
` (21 subsequent siblings)
22 siblings, 2 replies; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-02 10:06 UTC (permalink / raw)
To: u-boot
Added a misc driver to handle OTP memory in SiFive SoCs.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
---
drivers/misc/Kconfig | 7 +
drivers/misc/Makefile | 1 +
drivers/misc/sifive-otp.c | 273 ++++++++++++++++++++++++++++++++++++++
3 files changed, 281 insertions(+)
create mode 100644 drivers/misc/sifive-otp.c
diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig
index 766402745d..03464f1010 100644
--- a/drivers/misc/Kconfig
+++ b/drivers/misc/Kconfig
@@ -68,6 +68,13 @@ config ROCKCHIP_OTP
addressing and a length or through child-nodes that are generated
based on the e-fuse map retrieved from the DTS.
+config SIFIVE_OTP
+ bool "SiFive eMemory OTP driver"
+ depends on RISCV && MISC
+ help
+ Enable support for reading and writing the eMemory OTP on the
+ SiFive SoCs.
+
config VEXPRESS_CONFIG
bool "Enable support for Arm Versatile Express config bus"
depends on MISC
diff --git a/drivers/misc/Makefile b/drivers/misc/Makefile
index 68e0e7ad17..ed6bfc1356 100644
--- a/drivers/misc/Makefile
+++ b/drivers/misc/Makefile
@@ -58,6 +58,7 @@ obj-$(CONFIG_$(SPL_)PWRSEQ) += pwrseq-uclass.o
obj-$(CONFIG_QFW) += qfw.o
obj-$(CONFIG_ROCKCHIP_EFUSE) += rockchip-efuse.o
obj-$(CONFIG_ROCKCHIP_OTP) += rockchip-otp.o
+obj-$(CONFIG_SIFIVE_OTP) += sifive-otp.o
obj-$(CONFIG_SANDBOX) += syscon_sandbox.o misc_sandbox.o
obj-$(CONFIG_SMSC_LPC47M) += smsc_lpc47m.o
obj-$(CONFIG_SMSC_SIO1007) += smsc_sio1007.o
diff --git a/drivers/misc/sifive-otp.c b/drivers/misc/sifive-otp.c
new file mode 100644
index 0000000000..6a788f540d
--- /dev/null
+++ b/drivers/misc/sifive-otp.c
@@ -0,0 +1,273 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * This is a driver for the eMemory EG004K32TQ028XW01 NeoFuse
+ * One-Time-Programmable (OTP) memory used within the SiFive FU540.
+ * It is documented in the FU540 manual here:
+ * https://www.sifive.com/documentation/chips/freedom-u540-c000-manual/
+ *
+ * Copyright (C) 2018 Philipp Hug <philipp@hug.cx>
+ * Copyright (C) 2018 Joey Hewitt <joey@joeyhewitt.com>
+ *
+ * Copyright (C) 2020 SiFive, Inc
+ */
+
+/*
+ * The FU540 stores 4096x32 bit (16KiB) values.
+ * Index 0x00-0xff are reserved for SiFive internal use. (first 1KiB)
+ * Right now first 1KiB is used to store only serial number.
+ */
+
+#include <common.h>
+#include <dm/device.h>
+#include <dm/read.h>
+#include <linux/io.h>
+#include <misc.h>
+
+#define BYTES_PER_FUSE 4
+
+#define PA_RESET_VAL 0x00
+#define PAS_RESET_VAL 0x00
+#define PAIO_RESET_VAL 0x00
+#define PDIN_RESET_VAL 0x00
+#define PTM_RESET_VAL 0x00
+
+#define PCLK_ENABLE_VAL BIT(0)
+#define PCLK_DISABLE_VAL 0x00
+
+#define PWE_WRITE_ENABLE BIT(0)
+#define PWE_WRITE_DISABLE 0x00
+
+#define PTM_FUSE_PROGRAM_VAL BIT(1)
+
+#define PCE_ENABLE_INPUT BIT(0)
+#define PCE_DISABLE_INPUT 0x00
+
+#define PPROG_ENABLE_INPUT BIT(0)
+#define PPROG_DISABLE_INPUT 0x00
+
+#define PTRIM_ENABLE_INPUT BIT(0)
+#define PTRIM_DISABLE_INPUT 0x00
+
+#define PDSTB_DEEP_STANDBY_ENABLE BIT(0)
+#define PDSTB_DEEP_STANDBY_DISABLE 0x00
+
+/* Tpw - Program Pulse width delay */
+#define TPW_DELAY 20
+
+/* Tpwi - Program Pulse interval delay */
+#define TPWI_DELAY 5
+
+/* Tasp - Program address setup delay */
+#define TASP_DELAY 1
+
+/* Tcd - read data access delay */
+#define TCD_DELAY 40
+
+/* Tkl - clok pulse low delay */
+#define TKL_DELAY 10
+
+/* Tms - PTM mode setup delay */
+#define TMS_DELAY 1
+
+struct sifive_otp_regs {
+ u32 pa; /* Address input */
+ u32 paio; /* Program address input */
+ u32 pas; /* Program redundancy cell selection input */
+ u32 pce; /* OTP Macro enable input */
+ u32 pclk; /* Clock input */
+ u32 pdin; /* Write data input */
+ u32 pdout; /* Read data output */
+ u32 pdstb; /* Deep standby mode enable input (active low) */
+ u32 pprog; /* Program mode enable input */
+ u32 ptc; /* Test column enable input */
+ u32 ptm; /* Test mode enable input */
+ u32 ptm_rep;/* Repair function test mode enable input */
+ u32 ptr; /* Test row enable input */
+ u32 ptrim; /* Repair function enable input */
+ u32 pwe; /* Write enable input (defines program cycle) */
+};
+
+struct sifive_otp_platdata {
+ struct sifive_otp_regs __iomem *regs;
+ u32 total_fuses;
+};
+
+/*
+ * offset and size are assumed aligned to the size of the fuses (32-bit).
+ */
+static int sifive_otp_read(struct udevice *dev, int offset,
+ void *buf, int size)
+{
+ struct sifive_otp_platdata *plat = dev_get_platdata(dev);
+ struct sifive_otp_regs *regs = (struct sifive_otp_regs *)plat->regs;
+
+ /* Check if offset and size are multiple of BYTES_PER_FUSE */
+ if ((size % BYTES_PER_FUSE) || (offset % BYTES_PER_FUSE)) {
+ printf("%s: size and offset must be multiple of 4.\n",
+ __func__);
+ return -EINVAL;
+ }
+
+ int fuseidx = offset / BYTES_PER_FUSE;
+ int fusecount = size / BYTES_PER_FUSE;
+
+ /* check bounds */
+ if (offset < 0 || size < 0)
+ return -EINVAL;
+ if (fuseidx >= plat->total_fuses)
+ return -EINVAL;
+ if ((fuseidx + fusecount) > plat->total_fuses)
+ return -EINVAL;
+
+ u32 fusebuf[fusecount];
+
+ /* init OTP */
+ writel(PDSTB_DEEP_STANDBY_ENABLE, ®s->pdstb);
+ writel(PTRIM_ENABLE_INPUT, ®s->ptrim);
+ writel(PCE_ENABLE_INPUT, ®s->pce);
+
+ /* read all requested fuses */
+ for (unsigned int i = 0; i < fusecount; i++, fuseidx++) {
+ writel(fuseidx, ®s->pa);
+
+ /* cycle clock to read */
+ writel(PCLK_ENABLE_VAL, ®s->pclk);
+ ndelay(TCD_DELAY * 1000);
+ writel(PCLK_DISABLE_VAL, ®s->pclk);
+ ndelay(TKL_DELAY * 1000);
+
+ /* read the value */
+ fusebuf[i] = readl(®s->pdout);
+ }
+
+ /* shut down */
+ writel(PCE_DISABLE_INPUT, ®s->pce);
+ writel(PTRIM_DISABLE_INPUT, ®s->ptrim);
+ writel(PDSTB_DEEP_STANDBY_DISABLE, ®s->pdstb);
+
+ /* copy out */
+ memcpy(buf, fusebuf, size);
+
+ return size;
+}
+
+/*
+ * Caution:
+ * OTP can be written only once, so use carefully.
+ *
+ * offset and size are assumed aligned to the size of the fuses (32-bit).
+ */
+static int sifive_otp_write(struct udevice *dev, int offset,
+ const void *buf, int size)
+{
+ struct sifive_otp_platdata *plat = dev_get_platdata(dev);
+ struct sifive_otp_regs *regs = (struct sifive_otp_regs *)plat->regs;
+
+ /* Check if offset and size are multiple of BYTES_PER_FUSE */
+ if ((size % BYTES_PER_FUSE) || (offset % BYTES_PER_FUSE)) {
+ printf("%s: size and offset must be multiple of 4.\n",
+ __func__);
+ return -EINVAL;
+ }
+
+ int fuseidx = offset / BYTES_PER_FUSE;
+ int fusecount = size / BYTES_PER_FUSE;
+ u32 *write_buf = (u32 *)buf;
+ u32 write_data;
+ int i, pas, bit;
+
+ /* check bounds */
+ if (offset < 0 || size < 0)
+ return -EINVAL;
+ if (fuseidx >= plat->total_fuses)
+ return -EINVAL;
+ if ((fuseidx + fusecount) > plat->total_fuses)
+ return -EINVAL;
+
+ /* init OTP */
+ writel(PDSTB_DEEP_STANDBY_ENABLE, ®s->pdstb);
+ writel(PTRIM_ENABLE_INPUT, ®s->ptrim);
+
+ /* reset registers */
+ writel(PCLK_DISABLE_VAL, ®s->pclk);
+ writel(PA_RESET_VAL, ®s->pa);
+ writel(PAS_RESET_VAL, ®s->pas);
+ writel(PAIO_RESET_VAL, ®s->paio);
+ writel(PDIN_RESET_VAL, ®s->pdin);
+ writel(PWE_WRITE_DISABLE, ®s->pwe);
+ writel(PTM_FUSE_PROGRAM_VAL, ®s->ptm);
+ ndelay(TMS_DELAY * 1000);
+
+ writel(PCE_ENABLE_INPUT, ®s->pce);
+ writel(PPROG_ENABLE_INPUT, ®s->pprog);
+
+ /* write all requested fuses */
+ for (i = 0; i < fusecount; i++, fuseidx++) {
+ writel(fuseidx, ®s->pa);
+ write_data = *(write_buf++);
+
+ for (pas = 0; pas < 2; pas++) {
+ writel(pas, ®s->pas);
+
+ for (bit = 0; bit < 32; bit++) {
+ writel(bit, ®s->paio);
+ writel(((write_data >> bit) & 1),
+ ®s->pdin);
+ ndelay(TASP_DELAY * 1000);
+
+ writel(PWE_WRITE_ENABLE, ®s->pwe);
+ udelay(TPW_DELAY);
+ writel(PWE_WRITE_DISABLE, ®s->pwe);
+ udelay(TPWI_DELAY);
+ }
+ }
+
+ writel(PAS_RESET_VAL, ®s->pas);
+ }
+
+ /* shut down */
+ writel(PWE_WRITE_DISABLE, ®s->pwe);
+ writel(PPROG_DISABLE_INPUT, ®s->pprog);
+ writel(PCE_DISABLE_INPUT, ®s->pce);
+ writel(PTM_RESET_VAL, ®s->ptm);
+
+ writel(PTRIM_DISABLE_INPUT, ®s->ptrim);
+ writel(PDSTB_DEEP_STANDBY_DISABLE, ®s->pdstb);
+
+ return size;
+}
+
+static int sifive_otp_ofdata_to_platdata(struct udevice *dev)
+{
+ struct sifive_otp_platdata *plat = dev_get_platdata(dev);
+ int ret;
+
+ plat->regs = dev_read_addr_ptr(dev);
+
+ ret = dev_read_u32(dev, "fuse-count", &plat->total_fuses);
+ if (ret < 0) {
+ pr_err("\"fuse-count\" not found\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+static const struct misc_ops sifive_otp_ops = {
+ .read = sifive_otp_read,
+ .write = sifive_otp_write,
+};
+
+static const struct udevice_id sifive_otp_ids[] = {
+ { .compatible = "sifive,fu540-c000-otp" },
+ {}
+};
+
+U_BOOT_DRIVER(sifive_otp) = {
+ .name = "sifive_otp",
+ .id = UCLASS_MISC,
+ .of_match = sifive_otp_ids,
+ .ofdata_to_platdata = sifive_otp_ofdata_to_platdata,
+ .platdata_auto_alloc_size = sizeof(struct sifive_otp_platdata),
+ .ops = &sifive_otp_ops,
+};
--
2.17.1
^ permalink raw reply related [flat|nested] 118+ messages in thread
* [PATCH v7 02/22] riscv: sifive: fu540: Use OTP DM driver for serial environment variable
2020-05-02 10:06 [PATCH v7 00/22] RISC-V SiFive FU540 support SPL Pragnesh Patel
2020-05-02 10:06 ` [PATCH v7 01/22] misc: add driver for the SiFive otp controller Pragnesh Patel
@ 2020-05-02 10:06 ` Pragnesh Patel
2020-05-02 12:28 ` Bin Meng
2020-05-02 10:06 ` [PATCH v7 03/22] riscv: Add _image_binary_end for SPL Pragnesh Patel
` (20 subsequent siblings)
22 siblings, 1 reply; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-02 10:06 UTC (permalink / raw)
To: u-boot
Use the OTP DM driver to set the serial environment variable.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
---
arch/riscv/dts/fu540-c000-u-boot.dtsi | 14 +++
.../dts/hifive-unleashed-a00-u-boot.dtsi | 2 +
board/sifive/fu540/Kconfig | 2 +
board/sifive/fu540/fu540.c | 111 ++++++------------
4 files changed, 57 insertions(+), 72 deletions(-)
create mode 100644 arch/riscv/dts/fu540-c000-u-boot.dtsi
diff --git a/arch/riscv/dts/fu540-c000-u-boot.dtsi b/arch/riscv/dts/fu540-c000-u-boot.dtsi
new file mode 100644
index 0000000000..db55773bd2
--- /dev/null
+++ b/arch/riscv/dts/fu540-c000-u-boot.dtsi
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * (C) Copyright 2019 SiFive, Inc
+ */
+
+/ {
+ soc {
+ otp: otp at 10070000 {
+ compatible = "sifive,fu540-c000-otp";
+ reg = <0x0 0x10070000 0x0 0x0FFF>;
+ fuse-count = <0x1000>;
+ };
+ };
+};
diff --git a/arch/riscv/dts/hifive-unleashed-a00-u-boot.dtsi b/arch/riscv/dts/hifive-unleashed-a00-u-boot.dtsi
index 2aebfab646..9af089ffe7 100644
--- a/arch/riscv/dts/hifive-unleashed-a00-u-boot.dtsi
+++ b/arch/riscv/dts/hifive-unleashed-a00-u-boot.dtsi
@@ -3,6 +3,8 @@
* Copyright (C) 2019 Jagan Teki <jagan@amarulasolutions.com>
*/
+#include "fu540-c000-u-boot.dtsi"
+
/ {
aliases {
spi0 = &qspi0;
diff --git a/board/sifive/fu540/Kconfig b/board/sifive/fu540/Kconfig
index 75661f35f8..4330ac4491 100644
--- a/board/sifive/fu540/Kconfig
+++ b/board/sifive/fu540/Kconfig
@@ -51,5 +51,7 @@ config BOARD_SPECIFIC_OPTIONS # dummy
imply SIFIVE_GPIO
imply CMD_GPIO
imply SMP
+ imply MISC
+ imply SIFIVE_OTP
endif
diff --git a/board/sifive/fu540/fu540.c b/board/sifive/fu540/fu540.c
index 47a2090251..540638c919 100644
--- a/board/sifive/fu540/fu540.c
+++ b/board/sifive/fu540/fu540.c
@@ -10,94 +10,61 @@
#include <dm.h>
#include <linux/delay.h>
#include <linux/io.h>
+#include <misc.h>
+
+/*
+ * This define is a value used for error/unknown serial.
+ * If we really care about distinguishing errors and 0 is
+ * valid, we'll need a different one.
+ */
+#define ERROR_READING_SERIAL_NUMBER 0
#ifdef CONFIG_MISC_INIT_R
-#define FU540_OTP_BASE_ADDR 0x10070000
-
-struct fu540_otp_regs {
- u32 pa; /* Address input */
- u32 paio; /* Program address input */
- u32 pas; /* Program redundancy cell selection input */
- u32 pce; /* OTP Macro enable input */
- u32 pclk; /* Clock input */
- u32 pdin; /* Write data input */
- u32 pdout; /* Read data output */
- u32 pdstb; /* Deep standby mode enable input (active low) */
- u32 pprog; /* Program mode enable input */
- u32 ptc; /* Test column enable input */
- u32 ptm; /* Test mode enable input */
- u32 ptm_rep;/* Repair function test mode enable input */
- u32 ptr; /* Test row enable input */
- u32 ptrim; /* Repair function enable input */
- u32 pwe; /* Write enable input (defines program cycle) */
-} __packed;
-
-#define BYTES_PER_FUSE 4
-#define NUM_FUSES 0x1000
-
-static int fu540_otp_read(int offset, void *buf, int size)
+#if CONFIG_IS_ENABLED(SIFIVE_OTP)
+static u32 otp_read_serialnum(struct udevice *dev)
{
- struct fu540_otp_regs *regs = (void __iomem *)FU540_OTP_BASE_ADDR;
- unsigned int i;
- int fuseidx = offset / BYTES_PER_FUSE;
- int fusecount = size / BYTES_PER_FUSE;
- u32 fusebuf[fusecount];
-
- /* check bounds */
- if (offset < 0 || size < 0)
- return -EINVAL;
- if (fuseidx >= NUM_FUSES)
- return -EINVAL;
- if ((fuseidx + fusecount) > NUM_FUSES)
- return -EINVAL;
+ int ret;
+ u32 serial[2] = {0};
- /* init OTP */
- writel(0x01, ®s->pdstb); /* wake up from stand-by */
- writel(0x01, ®s->ptrim); /* enable repair function */
- writel(0x01, ®s->pce); /* enable input */
-
- /* read all requested fuses */
- for (i = 0; i < fusecount; i++, fuseidx++) {
- writel(fuseidx, ®s->pa);
-
- /* cycle clock to read */
- writel(0x01, ®s->pclk);
- mdelay(1);
- writel(0x00, ®s->pclk);
- mdelay(1);
-
- /* read the value */
- fusebuf[i] = readl(®s->pdout);
- }
+ for (int i = 0xfe * 4; i > 0; i -= 8) {
+ ret = misc_read(dev, i, serial, sizeof(serial));
- /* shut down */
- writel(0, ®s->pce);
- writel(0, ®s->ptrim);
- writel(0, ®s->pdstb);
+ if (ret != sizeof(serial)) {
+ printf("%s: error reading serial from OTP\n", __func__);
+ break;
+ }
- /* copy out */
- memcpy(buf, fusebuf, size);
+ if (serial[0] == ~serial[1])
+ return serial[0];
+ }
- return 0;
+ return ERROR_READING_SERIAL_NUMBER;
}
+#endif
static u32 fu540_read_serialnum(void)
{
+ u32 serial = ERROR_READING_SERIAL_NUMBER;
+
+#if CONFIG_IS_ENABLED(SIFIVE_OTP)
+ struct udevice *dev;
int ret;
- u32 serial[2] = {0};
- for (int i = 0xfe * 4; i > 0; i -= 8) {
- ret = fu540_otp_read(i, serial, sizeof(serial));
- if (ret) {
- printf("%s: error reading from OTP\n", __func__);
- break;
- }
- if (serial[0] == ~serial[1])
- return serial[0];
+ /* init OTP */
+ ret = uclass_get_device_by_driver(UCLASS_MISC,
+ DM_GET_DRIVER(sifive_otp), &dev);
+
+ if (ret) {
+ debug("%s: could not find otp device\n", __func__);
+ return serial;
}
- return 0;
+ /* read serial from OTP and set env var */
+ serial = otp_read_serialnum(dev);
+#endif
+
+ return serial;
}
static void fu540_setup_macaddr(u32 serialnum)
--
2.17.1
^ permalink raw reply related [flat|nested] 118+ messages in thread
* [PATCH v7 03/22] riscv: Add _image_binary_end for SPL
2020-05-02 10:06 [PATCH v7 00/22] RISC-V SiFive FU540 support SPL Pragnesh Patel
2020-05-02 10:06 ` [PATCH v7 01/22] misc: add driver for the SiFive otp controller Pragnesh Patel
2020-05-02 10:06 ` [PATCH v7 02/22] riscv: sifive: fu540: Use OTP DM driver for serial environment variable Pragnesh Patel
@ 2020-05-02 10:06 ` Pragnesh Patel
2020-05-02 12:28 ` Bin Meng
2020-05-02 10:06 ` [PATCH v7 04/22] lib: Makefile: build crc7.c when CONFIG_MMC_SPI Pragnesh Patel
` (19 subsequent siblings)
22 siblings, 1 reply; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-02 10:06 UTC (permalink / raw)
To: u-boot
For SPL_SEPARATE_BSS, Device tree will be put at _image_binary_end
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
---
arch/riscv/cpu/u-boot-spl.lds | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/riscv/cpu/u-boot-spl.lds b/arch/riscv/cpu/u-boot-spl.lds
index 955dd3106d..d0495ce248 100644
--- a/arch/riscv/cpu/u-boot-spl.lds
+++ b/arch/riscv/cpu/u-boot-spl.lds
@@ -72,6 +72,7 @@ SECTIONS
. = ALIGN(4);
_end = .;
+ _image_binary_end = .;
.bss : {
__bss_start = .;
--
2.17.1
^ permalink raw reply related [flat|nested] 118+ messages in thread
* [PATCH v7 04/22] lib: Makefile: build crc7.c when CONFIG_MMC_SPI
2020-05-02 10:06 [PATCH v7 00/22] RISC-V SiFive FU540 support SPL Pragnesh Patel
` (2 preceding siblings ...)
2020-05-02 10:06 ` [PATCH v7 03/22] riscv: Add _image_binary_end for SPL Pragnesh Patel
@ 2020-05-02 10:06 ` Pragnesh Patel
2020-05-02 10:29 ` Heinrich Schuchardt
2020-05-02 12:28 ` Bin Meng
2020-05-02 10:06 ` [PATCH v7 05/22] riscv: sifive: dts: fu540: Add board -u-boot.dtsi files Pragnesh Patel
` (18 subsequent siblings)
22 siblings, 2 replies; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-02 10:06 UTC (permalink / raw)
To: u-boot
When build U-Boot SPL, meet an issue of undefined reference to
'crc7' for drivers/mmc/mmc_spi.c, so let's compile crc7.c when
CONFIG_MMC_SPI selected.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
---
common/spl/Kconfig | 6 ++++++
drivers/mmc/Kconfig | 1 +
lib/Makefile | 1 +
3 files changed, 8 insertions(+)
diff --git a/common/spl/Kconfig b/common/spl/Kconfig
index ef5bf66696..d1f0e6bc4c 100644
--- a/common/spl/Kconfig
+++ b/common/spl/Kconfig
@@ -401,6 +401,12 @@ config SPL_CRC32_SUPPORT
for detected accidental image corruption. For secure applications you
should consider SHA1 or SHA256.
+config SPL_CRC7_SUPPORT
+ bool "Support CRC7"
+ help
+ Enable CRC7 hashing for drivers which are using in SPL.
+ This is a 32-bit checksum value that can be used to verify images.
+
config SPL_MD5_SUPPORT
bool "Support MD5"
depends on SPL_FIT
diff --git a/drivers/mmc/Kconfig b/drivers/mmc/Kconfig
index 8f0df568b9..139599072a 100644
--- a/drivers/mmc/Kconfig
+++ b/drivers/mmc/Kconfig
@@ -49,6 +49,7 @@ if MMC
config MMC_SPI
bool "Support for SPI-based MMC controller"
depends on DM_MMC && DM_SPI
+ select SPL_CRC7_SUPPORT if SPL
help
This selects SPI-based MMC controllers.
If you have an MMC controller on a SPI bus, say Y here.
diff --git a/lib/Makefile b/lib/Makefile
index c6f862b0c2..fcd934857f 100644
--- a/lib/Makefile
+++ b/lib/Makefile
@@ -80,6 +80,7 @@ endif
ifdef CONFIG_SPL_BUILD
obj-$(CONFIG_SPL_YMODEM_SUPPORT) += crc16.o
+obj-$(CONFIG_SPL_CRC7_SUPPORT) += crc7.o
obj-$(CONFIG_$(SPL_TPL_)HASH_SUPPORT) += crc16.o
obj-y += net_utils.o
endif
--
2.17.1
^ permalink raw reply related [flat|nested] 118+ messages in thread
* [PATCH v7 05/22] riscv: sifive: dts: fu540: Add board -u-boot.dtsi files
2020-05-02 10:06 [PATCH v7 00/22] RISC-V SiFive FU540 support SPL Pragnesh Patel
` (3 preceding siblings ...)
2020-05-02 10:06 ` [PATCH v7 04/22] lib: Makefile: build crc7.c when CONFIG_MMC_SPI Pragnesh Patel
@ 2020-05-02 10:06 ` Pragnesh Patel
2020-05-02 10:06 ` [PATCH v7 06/22] sifive: fu540: add ddr driver Pragnesh Patel
` (17 subsequent siblings)
22 siblings, 0 replies; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-02 10:06 UTC (permalink / raw)
To: u-boot
Devicetree files in FU540 platform is synced from Linux, like other
platforms does. Apart from these U-Boot in FU540 would also require
some U-Boot specific node like clint.
So, create board specific -u-boot.dtsi files. This would help of
maintain U-Boot specific changes separately without touching Linux
dts(i) files which indeed easy for syncing from Linux between
releases.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
---
arch/riscv/dts/fu540-c000-u-boot.dtsi | 54 +++++++++++++++++++
.../dts/hifive-unleashed-a00-u-boot.dtsi | 15 ++++++
2 files changed, 69 insertions(+)
diff --git a/arch/riscv/dts/fu540-c000-u-boot.dtsi b/arch/riscv/dts/fu540-c000-u-boot.dtsi
index db55773bd2..387b13bdfb 100644
--- a/arch/riscv/dts/fu540-c000-u-boot.dtsi
+++ b/arch/riscv/dts/fu540-c000-u-boot.dtsi
@@ -4,11 +4,65 @@
*/
/ {
+ cpus {
+ u-boot,dm-spl;
+ cpu0: cpu at 0 {
+ u-boot,dm-spl;
+ status = "okay";
+ cpu0_intc: interrupt-controller {
+ u-boot,dm-spl;
+ };
+ };
+ cpu1: cpu at 1 {
+ u-boot,dm-spl;
+ cpu1_intc: interrupt-controller {
+ u-boot,dm-spl;
+ };
+ };
+ cpu2: cpu at 2 {
+ u-boot,dm-spl;
+ cpu2_intc: interrupt-controller {
+ u-boot,dm-spl;
+ };
+ };
+ cpu3: cpu at 3 {
+ u-boot,dm-spl;
+ cpu3_intc: interrupt-controller {
+ u-boot,dm-spl;
+ };
+ };
+ cpu4: cpu at 4 {
+ u-boot,dm-spl;
+ cpu4_intc: interrupt-controller {
+ u-boot,dm-spl;
+ };
+ };
+ };
+
soc {
+ u-boot,dm-spl;
otp: otp at 10070000 {
compatible = "sifive,fu540-c000-otp";
reg = <0x0 0x10070000 0x0 0x0FFF>;
fuse-count = <0x1000>;
};
+ clint at 2000000 {
+ compatible = "riscv,clint0";
+ interrupts-extended = <&cpu0_intc 3 &cpu0_intc 7 &cpu1_intc 3 &cpu1_intc 7 &cpu2_intc 3 &cpu2_intc 7 &cpu3_intc 3 &cpu3_intc 7 &cpu4_intc 3 &cpu4_intc 7>;
+ reg = <0x0 0x2000000 0x0 0xc0000>;
+ u-boot,dm-spl;
+ };
};
};
+
+&prci {
+ u-boot,dm-spl;
+};
+
+&uart0 {
+ u-boot,dm-spl;
+};
+
+&qspi2 {
+ u-boot,dm-spl;
+};
diff --git a/arch/riscv/dts/hifive-unleashed-a00-u-boot.dtsi b/arch/riscv/dts/hifive-unleashed-a00-u-boot.dtsi
index 9af089ffe7..9787332bf1 100644
--- a/arch/riscv/dts/hifive-unleashed-a00-u-boot.dtsi
+++ b/arch/riscv/dts/hifive-unleashed-a00-u-boot.dtsi
@@ -10,4 +10,19 @@
spi0 = &qspi0;
spi2 = &qspi2;
};
+
+ hfclk {
+ u-boot,dm-spl;
+ };
+
+ rtcclk {
+ u-boot,dm-spl;
+ };
+
+};
+
+&qspi2 {
+ mmc at 0 {
+ u-boot,dm-spl;
+ };
};
--
2.17.1
^ permalink raw reply related [flat|nested] 118+ messages in thread
* [PATCH v7 06/22] sifive: fu540: add ddr driver
2020-05-02 10:06 [PATCH v7 00/22] RISC-V SiFive FU540 support SPL Pragnesh Patel
` (4 preceding siblings ...)
2020-05-02 10:06 ` [PATCH v7 05/22] riscv: sifive: dts: fu540: Add board -u-boot.dtsi files Pragnesh Patel
@ 2020-05-02 10:06 ` Pragnesh Patel
2020-05-02 12:28 ` Bin Meng
2020-05-02 15:59 ` Jagan Teki
2020-05-02 10:06 ` [PATCH v7 07/22] sifive: dts: fu540: Add DDR controller and phy register settings Pragnesh Patel
` (16 subsequent siblings)
22 siblings, 2 replies; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-02 10:06 UTC (permalink / raw)
To: u-boot
Add driver for fu540 to support ddr initialization in SPL.
This driver is based on FSBL
(https://github.com/sifive/freedom-u540-c000-bootloader.git)
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
---
board/sifive/fu540/Kconfig | 2 +
drivers/ram/Kconfig | 1 +
drivers/ram/Makefile | 2 +
drivers/ram/sifive/Kconfig | 13 +
drivers/ram/sifive/Makefile | 6 +
drivers/ram/sifive/sdram_fu540.c | 416 +++++++++++++++++++++++++++++++
6 files changed, 440 insertions(+)
create mode 100644 drivers/ram/sifive/Kconfig
create mode 100644 drivers/ram/sifive/Makefile
create mode 100644 drivers/ram/sifive/sdram_fu540.c
diff --git a/board/sifive/fu540/Kconfig b/board/sifive/fu540/Kconfig
index 4330ac4491..d41c305227 100644
--- a/board/sifive/fu540/Kconfig
+++ b/board/sifive/fu540/Kconfig
@@ -19,6 +19,8 @@ config SYS_TEXT_BASE
config BOARD_SPECIFIC_OPTIONS # dummy
def_bool y
select GENERIC_RISCV
+ select RAM
+ select SPL_RAM if SPL
imply CMD_DHCP
imply CMD_EXT2
imply CMD_EXT4
diff --git a/drivers/ram/Kconfig b/drivers/ram/Kconfig
index 56fea7c94c..66074d1feb 100644
--- a/drivers/ram/Kconfig
+++ b/drivers/ram/Kconfig
@@ -75,3 +75,4 @@ config IMXRT_SDRAM
source "drivers/ram/rockchip/Kconfig"
source "drivers/ram/stm32mp1/Kconfig"
+source "drivers/ram/sifive/Kconfig"
diff --git a/drivers/ram/Makefile b/drivers/ram/Makefile
index 5c897410c6..769c9d6218 100644
--- a/drivers/ram/Makefile
+++ b/drivers/ram/Makefile
@@ -17,3 +17,5 @@ obj-$(CONFIG_ARCH_MEDIATEK) += mediatek/
obj-$(CONFIG_K3_J721E_DDRSS) += k3-j721e/
obj-$(CONFIG_IMXRT_SDRAM) += imxrt_sdram.o
+
+obj-$(CONFIG_RAM_SIFIVE) += sifive/
diff --git a/drivers/ram/sifive/Kconfig b/drivers/ram/sifive/Kconfig
new file mode 100644
index 0000000000..6aca22ab2a
--- /dev/null
+++ b/drivers/ram/sifive/Kconfig
@@ -0,0 +1,13 @@
+config RAM_SIFIVE
+ bool "Ram drivers support for SiFive SoCs"
+ depends on RAM && RISCV
+ default y
+ help
+ This enables support for ram drivers of SiFive SoCs.
+
+config SIFIVE_FU540_DDR
+ bool "SiFive FU540 DDR driver"
+ depends on RAM_SIFIVE
+ default y if TARGET_SIFIVE_FU540
+ help
+ This enables DDR support for the platforms based on SiFive FU540 SoC.
diff --git a/drivers/ram/sifive/Makefile b/drivers/ram/sifive/Makefile
new file mode 100644
index 0000000000..0187805199
--- /dev/null
+++ b/drivers/ram/sifive/Makefile
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# Copyright (c) 2020 SiFive, Inc
+#
+
+obj-$(CONFIG_SIFIVE_FU540_DDR) += sdram_fu540.o
diff --git a/drivers/ram/sifive/sdram_fu540.c b/drivers/ram/sifive/sdram_fu540.c
new file mode 100644
index 0000000000..0aa2b2b44a
--- /dev/null
+++ b/drivers/ram/sifive/sdram_fu540.c
@@ -0,0 +1,416 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * (C) Copyright 2020 SiFive, Inc.
+ *
+ * Authors:
+ * Pragnesh Patel <pragnesh.patel@sifive.com>
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <init.h>
+#include <ram.h>
+#include <regmap.h>
+#include <syscon.h>
+#include <asm/io.h>
+#include <clk.h>
+
+#define DENALI_CTL_0 0
+#define DENALI_CTL_21 21
+#define DENALI_CTL_120 120
+#define DENALI_CTL_132 132
+#define DENALI_CTL_136 136
+#define DENALI_CTL_170 170
+#define DENALI_CTL_181 181
+#define DENALI_CTL_182 182
+#define DENALI_CTL_184 184
+#define DENALI_CTL_208 208
+#define DENALI_CTL_209 209
+#define DENALI_CTL_210 210
+#define DENALI_CTL_212 212
+#define DENALI_CTL_214 214
+#define DENALI_CTL_216 216
+#define DENALI_CTL_224 224
+#define DENALI_CTL_225 225
+#define DENALI_CTL_260 260
+
+#define DENALI_PHY_1152 1152
+#define DENALI_PHY_1214 1214
+
+#define PAYLOAD_DEST 0x80000000
+#define DDR_MEM_SIZE (8UL * 1024UL * 1024UL * 1024UL)
+
+#define DRAM_CLASS_OFFSET 8
+#define DRAM_CLASS_DDR4 0xA
+#define OPTIMAL_RMODW_EN_OFFSET 0
+#define DISABLE_RD_INTERLEAVE_OFFSET 16
+#define OUT_OF_RANGE_OFFSET 1
+#define MULTIPLE_OUT_OF_RANGE_OFFSET 2
+#define PORT_COMMAND_CHANNEL_ERROR_OFFSET 7
+#define MC_INIT_COMPLETE_OFFSET 8
+#define LEVELING_OPERATION_COMPLETED_OFFSET 22
+#define DFI_PHY_WRLELV_MODE_OFFSET 24
+#define DFI_PHY_RDLVL_MODE_OFFSET 24
+#define DFI_PHY_RDLVL_GATE_MODE_OFFSET 0
+#define VREF_EN_OFFSET 24
+#define PORT_ADDR_PROTECTION_EN_OFFSET 0
+#define AXI0_ADDRESS_RANGE_ENABLE 8
+#define AXI0_RANGE_PROT_BITS_0_OFFSET 24
+#define RDLVL_EN_OFFSET 16
+#define RDLVL_GATE_EN_OFFSET 24
+#define WRLVL_EN_OFFSET 0
+
+#define PHY_RX_CAL_DQ0_0_OFFSET 0
+#define PHY_RX_CAL_DQ1_0_OFFSET 16
+
+struct fu540_ddrctl {
+ volatile u32 denali_ctl[265];
+};
+
+struct fu540_ddrphy {
+ volatile u32 denali_phy[1215];
+};
+
+/**
+ * struct ddr_info
+ *
+ * @dev : pointer for the device
+ * @info : UCLASS RAM information
+ * @ctl : DDR controller base address
+ * @phy : DDR PHY base address
+ * @ctrl : DDR control base address
+ * @physical_filter_ctrl : DDR physical filter control base address
+ */
+struct ddr_info {
+ struct udevice *dev;
+ struct ram_info info;
+ struct fu540_ddrctl *ctl;
+ struct fu540_ddrphy *phy;
+ struct clk ddr_clk;
+ u32 *physical_filter_ctrl;
+};
+
+#if defined(CONFIG_TPL_BUILD) || \
+ (!defined(CONFIG_TPL) && defined(CONFIG_SPL_BUILD))
+
+struct fu540_sdram_params {
+ struct fu540_ddrctl pctl_regs;
+ struct fu540_ddrphy phy_regs;
+};
+
+struct sifive_dmc_plat {
+#if CONFIG_IS_ENABLED(OF_PLATDATA)
+ struct dtd_sifive_fu540_dmc dtplat;
+#else
+ struct fu540_sdram_params sdram_params;
+#endif
+};
+
+/* n: Unit bytes */
+static void sdram_copy_to_reg(volatile u32 *dest,
+ volatile u32 *src, u32 n)
+{
+ int i;
+
+ for (i = 0; i < n / sizeof(u32); i++) {
+ writel(*src, dest);
+ src++;
+ dest++;
+ }
+}
+
+static void ddr_setuprangeprotection(volatile u32 *ctl, u64 end_addr)
+{
+ u32 end_addr_16kblocks = ((end_addr >> 14) & 0x7FFFFF) - 1;
+
+ writel(0x0, DENALI_CTL_209 + ctl);
+ writel(end_addr_16kblocks, DENALI_CTL_210 + ctl);
+ writel(0x0, DENALI_CTL_212 + ctl);
+ writel(0x0, DENALI_CTL_214 + ctl);
+ writel(0x0, DENALI_CTL_216 + ctl);
+ setbits_le32(DENALI_CTL_224 + ctl,
+ 0x3 << AXI0_RANGE_PROT_BITS_0_OFFSET);
+ writel(0xFFFFFFFF, DENALI_CTL_225 + ctl);
+ setbits_le32(DENALI_CTL_208 + ctl, 0x1 << AXI0_ADDRESS_RANGE_ENABLE);
+ setbits_le32(DENALI_CTL_208 + ctl,
+ 0x1 << PORT_ADDR_PROTECTION_EN_OFFSET);
+}
+
+static void ddr_start(volatile u32 *ctl, u32 *physical_filter_ctrl, u64 ddr_end)
+{
+ int val;
+
+ volatile u64 *filterreg = (volatile u64 *)physical_filter_ctrl;
+
+ setbits_le32(DENALI_CTL_0 + ctl, 0x1);
+
+ do {
+ val = readl(DENALI_CTL_132 + ctl) &
+ (1 << MC_INIT_COMPLETE_OFFSET);
+ } while (val == 0);
+
+ /* Disable the BusBlocker in front of the controller AXI slave ports */
+ filterreg[0] = 0x0f00000000000000UL | (ddr_end >> 2);
+}
+
+static void check_errata(u32 regbase, u32 updownreg)
+{
+ u64 fails = 0;
+ u32 dq = 0;
+ u32 down, up;
+ u8 failc0, failc1;
+ u32 phy_rx_cal_dqn_0_offset;
+
+ for (u32 bit = 0; bit < 2; bit++) {
+ if (bit == 0) {
+ phy_rx_cal_dqn_0_offset =
+ PHY_RX_CAL_DQ0_0_OFFSET;
+ } else {
+ phy_rx_cal_dqn_0_offset =
+ PHY_RX_CAL_DQ1_0_OFFSET;
+ }
+
+ down = (updownreg >>
+ phy_rx_cal_dqn_0_offset) & 0x3F;
+ up = (updownreg >>
+ (phy_rx_cal_dqn_0_offset + 6)) &
+ 0x3F;
+
+ failc0 = ((down == 0) && (up == 0x3F));
+ failc1 = ((up == 0) && (down == 0x3F));
+
+ /* print error message on failure */
+ if (failc0 || failc1) {
+ if (fails == 0)
+ printf("DDR error in fixing up\n");
+
+ fails |= (1 << dq);
+
+ char slicelsc = '0';
+ char slicemsc = '0';
+
+ slicelsc += (dq % 10);
+ slicemsc += (dq / 10);
+ printf("S ");
+ printf("%c", slicemsc);
+ printf("%c", slicelsc);
+
+ if (failc0)
+ printf("U");
+ else
+ printf("D");
+
+ printf("\n");
+ }
+ dq++;
+ }
+}
+
+static u64 ddr_phy_fixup(volatile u32 *ddrphyreg)
+{
+ u32 slicebase = 0;
+
+ /* check errata condition */
+ for (u32 slice = 0; slice < 8; slice++) {
+ u32 regbase = slicebase + 34;
+
+ for (u32 reg = 0; reg < 4; reg++) {
+ u32 updownreg = readl(regbase + reg + ddrphyreg);
+
+ check_errata(regbase, updownreg);
+ }
+ slicebase += 128;
+ }
+
+ return(0);
+}
+
+static u32 ddr_getdramclass(volatile u32 *ctl)
+{
+ u32 reg = readl(DENALI_CTL_0 + ctl);
+
+ return ((reg >> DRAM_CLASS_OFFSET) & 0xF);
+}
+
+static int fu540_ddr_setup(struct udevice *dev)
+{
+ struct ddr_info *priv = dev_get_priv(dev);
+ struct sifive_dmc_plat *plat = dev_get_platdata(dev);
+ struct fu540_sdram_params *params = &plat->sdram_params;
+ int ret, i;
+ u32 physet;
+ const u64 ddr_size = DDR_MEM_SIZE;
+ const u64 ddr_end = PAYLOAD_DEST + ddr_size;
+ volatile u32 *denali_ctl = &priv->ctl->denali_ctl[0];
+ volatile u32 *denali_phy = &priv->phy->denali_phy[0];
+
+ ret = dev_read_u32_array(dev, "sifive,sdram-params",
+ (u32 *)&plat->sdram_params,
+ sizeof(plat->sdram_params) / sizeof(u32));
+ if (ret) {
+ printf("%s: Cannot read sifive,sdram-params %d\n",
+ __func__, ret);
+ return ret;
+ }
+
+ sdram_copy_to_reg(&priv->ctl->denali_ctl[0],
+ ¶ms->pctl_regs.denali_ctl[0],
+ sizeof(struct fu540_ddrctl));
+
+ /* phy reset */
+ for (i = DENALI_PHY_1152; i <= DENALI_PHY_1214; i++) {
+ physet = params->phy_regs.denali_phy[i];
+ priv->phy->denali_phy[i] = physet;
+ }
+
+ for (i = 0; i < DENALI_PHY_1152; i++) {
+ physet = params->phy_regs.denali_phy[i];
+ priv->phy->denali_phy[i] = physet;
+ }
+
+ /* Disable read interleave DENALI_CTL_120 */
+ setbits_le32(DENALI_CTL_120 + denali_ctl,
+ 1 << DISABLE_RD_INTERLEAVE_OFFSET);
+
+ /* Disable optimal read/modify/write logic DENALI_CTL_21 */
+ clrbits_le32(DENALI_CTL_21 + denali_ctl, 1 << OPTIMAL_RMODW_EN_OFFSET);
+
+ /* Enable write Leveling DENALI_CTL_170 */
+ setbits_le32(DENALI_CTL_170 + denali_ctl, (1 << WRLVL_EN_OFFSET)
+ | (1 << DFI_PHY_WRLELV_MODE_OFFSET));
+
+ /* Enable read leveling DENALI_CTL_181 and DENALI_CTL_260 */
+ setbits_le32(DENALI_CTL_181 + denali_ctl,
+ 1 << DFI_PHY_RDLVL_MODE_OFFSET);
+ setbits_le32(DENALI_CTL_260 + denali_ctl, 1 << RDLVL_EN_OFFSET);
+
+ /* Enable read leveling gate DENALI_CTL_260 and DENALI_CTL_182 */
+ setbits_le32(DENALI_CTL_260 + denali_ctl, 1 << RDLVL_GATE_EN_OFFSET);
+ setbits_le32(DENALI_CTL_182 + denali_ctl,
+ 1 << DFI_PHY_RDLVL_GATE_MODE_OFFSET);
+
+ if (ddr_getdramclass(denali_ctl) == DRAM_CLASS_DDR4) {
+ /* Enable vref training DENALI_CTL_184 */
+ setbits_le32(DENALI_CTL_184 + denali_ctl, 1 << VREF_EN_OFFSET);
+ }
+
+ /* Mask off leveling completion interrupt DENALI_CTL_136 */
+ setbits_le32(DENALI_CTL_136 + denali_ctl,
+ 1 << LEVELING_OPERATION_COMPLETED_OFFSET);
+
+ /* Mask off MC init complete interrupt DENALI_CTL_136 */
+ setbits_le32(DENALI_CTL_136 + denali_ctl, 1 << MC_INIT_COMPLETE_OFFSET);
+
+ /* Mask off out of range interrupts DENALI_CTL_136 */
+ setbits_le32(DENALI_CTL_136 + denali_ctl, (1 << OUT_OF_RANGE_OFFSET)
+ | (1 << MULTIPLE_OUT_OF_RANGE_OFFSET));
+
+ /* set up range protection */
+ ddr_setuprangeprotection(denali_ctl, DDR_MEM_SIZE);
+
+ /* Mask off port command error interrupt DENALI_CTL_136 */
+ setbits_le32(DENALI_CTL_136 + denali_ctl,
+ 1 << PORT_COMMAND_CHANNEL_ERROR_OFFSET);
+
+ ddr_start(denali_ctl, priv->physical_filter_ctrl, ddr_end);
+
+ ddr_phy_fixup(denali_phy);
+
+ /* check size */
+ priv->info.size = get_ram_size((long *)priv->info.base,
+ DDR_MEM_SIZE);
+
+ debug("%s : %lx\n", __func__, priv->info.size);
+
+ /* check memory access for all memory */
+ if (priv->info.size != DDR_MEM_SIZE) {
+ printf("DDR invalid size : 0x%lx, expected 0x%lx\n",
+ priv->info.size, DDR_MEM_SIZE);
+ return -EINVAL;
+ }
+
+ return 0;
+}
+#endif
+
+static int fu540_ddr_probe(struct udevice *dev)
+{
+ struct ddr_info *priv = dev_get_priv(dev);
+
+#if defined(CONFIG_TPL_BUILD) || \
+ (!defined(CONFIG_TPL) && defined(CONFIG_SPL_BUILD))
+ struct regmap *map;
+ int ret;
+ u32 clock = 0;
+
+ debug("FU540 DDR probe\n");
+ priv->dev = dev;
+
+ ret = regmap_init_mem(dev_ofnode(dev), &map);
+ if (ret)
+ return ret;
+
+ ret = clk_get_by_index(dev, 0, &priv->ddr_clk);
+ if (ret) {
+ debug("clk get failed %d\n", ret);
+ return ret;
+ }
+
+ ret = dev_read_u32(dev, "clock-frequency", &clock);
+ if (ret) {
+ debug("clock-frequency not found in dt %d\n", ret);
+ return ret;
+ } else {
+ ret = clk_set_rate(&priv->ddr_clk, clock);
+ if (ret < 0) {
+ debug("Could not set DDR clock\n");
+ return ret;
+ }
+ }
+
+ ret = clk_enable(&priv->ddr_clk);
+ priv->ctl = regmap_get_range(map, 0);
+ priv->phy = regmap_get_range(map, 1);
+ priv->physical_filter_ctrl = regmap_get_range(map, 2);
+
+ priv->info.base = CONFIG_SYS_SDRAM_BASE;
+
+ priv->info.size = 0;
+ return fu540_ddr_setup(dev);
+#else
+ priv->info.base = CONFIG_SYS_SDRAM_BASE;
+ priv->info.size = DDR_MEM_SIZE;
+#endif
+ return 0;
+}
+
+static int fu540_ddr_get_info(struct udevice *dev, struct ram_info *info)
+{
+ struct ddr_info *priv = dev_get_priv(dev);
+
+ *info = priv->info;
+
+ return 0;
+}
+
+static struct ram_ops fu540_ddr_ops = {
+ .get_info = fu540_ddr_get_info,
+};
+
+static const struct udevice_id fu540_ddr_ids[] = {
+ { .compatible = "sifive,fu540-c000-ddr" },
+ { }
+};
+
+U_BOOT_DRIVER(fu540_ddr) = {
+ .name = "fu540_ddr",
+ .id = UCLASS_RAM,
+ .of_match = fu540_ddr_ids,
+ .ops = &fu540_ddr_ops,
+ .probe = fu540_ddr_probe,
+ .priv_auto_alloc_size = sizeof(struct ddr_info),
+#if defined(CONFIG_TPL_BUILD) || \
+ (!defined(CONFIG_TPL) && defined(CONFIG_SPL_BUILD))
+ .platdata_auto_alloc_size = sizeof(struct sifive_dmc_plat),
+#endif
+};
--
2.17.1
^ permalink raw reply related [flat|nested] 118+ messages in thread
* [PATCH v7 07/22] sifive: dts: fu540: Add DDR controller and phy register settings
2020-05-02 10:06 [PATCH v7 00/22] RISC-V SiFive FU540 support SPL Pragnesh Patel
` (5 preceding siblings ...)
2020-05-02 10:06 ` [PATCH v7 06/22] sifive: fu540: add ddr driver Pragnesh Patel
@ 2020-05-02 10:06 ` Pragnesh Patel
2020-05-02 12:28 ` Bin Meng
2020-05-02 10:06 ` [PATCH v7 08/22] riscv: sifive: dts: fu540: add U-Boot dmc node Pragnesh Patel
` (15 subsequent siblings)
22 siblings, 1 reply; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-02 10:06 UTC (permalink / raw)
To: u-boot
Add DDR controller and phy register settings, taken from fsbl
(https://github.com/sifive/freedom-u540-c000-bootloader.git)
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
---
...fu540-hifive-unleashed-a00-sdram-ddr4.dtsi | 1489 +++++++++++++++++
1 file changed, 1489 insertions(+)
create mode 100644 arch/riscv/dts/fu540-hifive-unleashed-a00-sdram-ddr4.dtsi
diff --git a/arch/riscv/dts/fu540-hifive-unleashed-a00-sdram-ddr4.dtsi b/arch/riscv/dts/fu540-hifive-unleashed-a00-sdram-ddr4.dtsi
new file mode 100644
index 0000000000..370c53800d
--- /dev/null
+++ b/arch/riscv/dts/fu540-hifive-unleashed-a00-sdram-ddr4.dtsi
@@ -0,0 +1,1489 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * (C) Copyright 2020 SiFive, Inc
+ */
+
+&dmc {
+ sifive,sdram-params = <
+ 0x00000a00 /* DENALI_CTL_00_DATA */
+ 0x00000000 /* DENALI_CTL_01_DATA */
+ 0x00000000 /* DENALI_CTL_02_DATA */
+ 0x00000000 /* DENALI_CTL_03_DATA */
+ 0x00000000 /* DENALI_CTL_04_DATA */
+ 0x00000000 /* DENALI_CTL_05_DATA */
+ 0x0000000a /* DENALI_CTL_06_DATA */
+ 0x0002d362 /* DENALI_CTL_07_DATA */
+ 0x00071073 /* DENALI_CTL_08_DATA */
+ 0x0a1c0255 /* DENALI_CTL_09_DATA */
+ 0x1c1c0400 /* DENALI_CTL_10_DATA */
+ 0x0404990b /* DENALI_CTL_11_DATA */
+ 0x2b050405 /* DENALI_CTL_12_DATA */
+ 0x0e0c081e /* DENALI_CTL_13_DATA */
+ 0x08090914 /* DENALI_CTL_14_DATA */
+ 0x00fde718 /* DENALI_CTL_15_DATA */
+ 0x00180a05 /* DENALI_CTL_16_DATA */
+ 0x008b130e /* DENALI_CTL_17_DATA */
+ 0x01000118 /* DENALI_CTL_18_DATA */
+ 0x0e032101 /* DENALI_CTL_19_DATA */
+ 0x00000000 /* DENALI_CTL_20_DATA */
+ 0x00000101 /* DENALI_CTL_21_DATA */
+ 0x00000000 /* DENALI_CTL_22_DATA */
+ 0x0a000000 /* DENALI_CTL_23_DATA */
+ 0x00000000 /* DENALI_CTL_24_DATA */
+ 0x01450100 /* DENALI_CTL_25_DATA */
+ 0x00001c36 /* DENALI_CTL_26_DATA */
+ 0x00000005 /* DENALI_CTL_27_DATA */
+ 0x00170006 /* DENALI_CTL_28_DATA */
+ 0x014e0300 /* DENALI_CTL_29_DATA */
+ 0x03010000 /* DENALI_CTL_30_DATA */
+ 0x000a0e00 /* DENALI_CTL_31_DATA */
+ 0x04030200 /* DENALI_CTL_32_DATA */
+ 0x0000031f /* DENALI_CTL_33_DATA */
+ 0x00070004 /* DENALI_CTL_34_DATA */
+ 0x00000000 /* DENALI_CTL_35_DATA */
+ 0x00000000 /* DENALI_CTL_36_DATA */
+ 0x00000000 /* DENALI_CTL_37_DATA */
+ 0x00000000 /* DENALI_CTL_38_DATA */
+ 0x00000000 /* DENALI_CTL_39_DATA */
+ 0x00000000 /* DENALI_CTL_40_DATA */
+ 0x00000000 /* DENALI_CTL_41_DATA */
+ 0x00000000 /* DENALI_CTL_42_DATA */
+ 0x00000000 /* DENALI_CTL_43_DATA */
+ 0x00000000 /* DENALI_CTL_44_DATA */
+ 0x00000000 /* DENALI_CTL_45_DATA */
+ 0x00000000 /* DENALI_CTL_46_DATA */
+ 0x00000000 /* DENALI_CTL_47_DATA */
+ 0x00000000 /* DENALI_CTL_48_DATA */
+ 0x00000000 /* DENALI_CTL_49_DATA */
+ 0x00000000 /* DENALI_CTL_50_DATA */
+ 0x00000000 /* DENALI_CTL_51_DATA */
+ 0x00000000 /* DENALI_CTL_52_DATA */
+ 0x00000000 /* DENALI_CTL_53_DATA */
+ 0x00000000 /* DENALI_CTL_54_DATA */
+ 0x00000000 /* DENALI_CTL_55_DATA */
+ 0x00000000 /* DENALI_CTL_56_DATA */
+ 0x00000000 /* DENALI_CTL_57_DATA */
+ 0x00000000 /* DENALI_CTL_58_DATA */
+ 0x00000000 /* DENALI_CTL_59_DATA */
+ 0x00000424 /* DENALI_CTL_60_DATA */
+ 0x00000201 /* DENALI_CTL_61_DATA */
+ 0x00001008 /* DENALI_CTL_62_DATA */
+ 0x00000000 /* DENALI_CTL_63_DATA */
+ 0x00000200 /* DENALI_CTL_64_DATA */
+ 0x00000000 /* DENALI_CTL_65_DATA */
+ 0x00000481 /* DENALI_CTL_66_DATA */
+ 0x00000400 /* DENALI_CTL_67_DATA */
+ 0x00000424 /* DENALI_CTL_68_DATA */
+ 0x00000201 /* DENALI_CTL_69_DATA */
+ 0x00001008 /* DENALI_CTL_70_DATA */
+ 0x00000000 /* DENALI_CTL_71_DATA */
+ 0x00000200 /* DENALI_CTL_72_DATA */
+ 0x00000000 /* DENALI_CTL_73_DATA */
+ 0x00000481 /* DENALI_CTL_74_DATA */
+ 0x00000400 /* DENALI_CTL_75_DATA */
+ 0x01010000 /* DENALI_CTL_76_DATA */
+ 0x00000000 /* DENALI_CTL_77_DATA */
+ 0x00000000 /* DENALI_CTL_78_DATA */
+ 0x00000000 /* DENALI_CTL_79_DATA */
+ 0x00000000 /* DENALI_CTL_80_DATA */
+ 0x00000000 /* DENALI_CTL_81_DATA */
+ 0x00000000 /* DENALI_CTL_82_DATA */
+ 0x00000000 /* DENALI_CTL_83_DATA */
+ 0x00000000 /* DENALI_CTL_84_DATA */
+ 0x00000000 /* DENALI_CTL_85_DATA */
+ 0x00000000 /* DENALI_CTL_86_DATA */
+ 0x00000000 /* DENALI_CTL_87_DATA */
+ 0x00000000 /* DENALI_CTL_88_DATA */
+ 0x00000000 /* DENALI_CTL_89_DATA */
+ 0x00000000 /* DENALI_CTL_90_DATA */
+ 0x00000000 /* DENALI_CTL_91_DATA */
+ 0x00000000 /* DENALI_CTL_92_DATA */
+ 0x00000000 /* DENALI_CTL_93_DATA */
+ 0x00000000 /* DENALI_CTL_94_DATA */
+ 0x00000000 /* DENALI_CTL_95_DATA */
+ 0x00000000 /* DENALI_CTL_96_DATA */
+ 0x00000000 /* DENALI_CTL_97_DATA */
+ 0x00000000 /* DENALI_CTL_98_DATA */
+ 0x00000000 /* DENALI_CTL_99_DATA */
+ 0x00000000 /* DENALI_CTL_100_DATA */
+ 0x00000000 /* DENALI_CTL_101_DATA */
+ 0x00000000 /* DENALI_CTL_102_DATA */
+ 0x00000000 /* DENALI_CTL_103_DATA */
+ 0x00000000 /* DENALI_CTL_104_DATA */
+ 0x00000003 /* DENALI_CTL_105_DATA */
+ 0x00000000 /* DENALI_CTL_106_DATA */
+ 0x00000000 /* DENALI_CTL_107_DATA */
+ 0x00000000 /* DENALI_CTL_108_DATA */
+ 0x00000000 /* DENALI_CTL_109_DATA */
+ 0x01000000 /* DENALI_CTL_110_DATA */
+ 0x00040000 /* DENALI_CTL_111_DATA */
+ 0x00800200 /* DENALI_CTL_112_DATA */
+ 0x00000200 /* DENALI_CTL_113_DATA */
+ 0x00000040 /* DENALI_CTL_114_DATA */
+ 0x01000100 /* DENALI_CTL_115_DATA */
+ 0x0a000002 /* DENALI_CTL_116_DATA */
+ 0x0101ffff /* DENALI_CTL_117_DATA */
+ 0x01010101 /* DENALI_CTL_118_DATA */
+ 0x01010101 /* DENALI_CTL_119_DATA */
+ 0x0000010b /* DENALI_CTL_120_DATA */
+ 0x00000c01 /* DENALI_CTL_121_DATA */
+ 0x00000000 /* DENALI_CTL_122_DATA */
+ 0x00000000 /* DENALI_CTL_123_DATA */
+ 0x00000000 /* DENALI_CTL_124_DATA */
+ 0x00000000 /* DENALI_CTL_125_DATA */
+ 0x00030300 /* DENALI_CTL_126_DATA */
+ 0x00000000 /* DENALI_CTL_127_DATA */
+ 0x00010001 /* DENALI_CTL_128_DATA */
+ 0x00000000 /* DENALI_CTL_129_DATA */
+ 0x00000000 /* DENALI_CTL_130_DATA */
+ 0x00000000 /* DENALI_CTL_131_DATA */
+ 0x00000000 /* DENALI_CTL_132_DATA */
+ 0x00000000 /* DENALI_CTL_133_DATA */
+ 0x00000000 /* DENALI_CTL_134_DATA */
+ 0x00000000 /* DENALI_CTL_135_DATA */
+ 0x00000000 /* DENALI_CTL_136_DATA */
+ 0x00000000 /* DENALI_CTL_137_DATA */
+ 0x00000000 /* DENALI_CTL_138_DATA */
+ 0x00000000 /* DENALI_CTL_139_DATA */
+ 0x00000000 /* DENALI_CTL_140_DATA */
+ 0x00000000 /* DENALI_CTL_141_DATA */
+ 0x00000000 /* DENALI_CTL_142_DATA */
+ 0x00000000 /* DENALI_CTL_143_DATA */
+ 0x00000000 /* DENALI_CTL_144_DATA */
+ 0x00000000 /* DENALI_CTL_145_DATA */
+ 0x00000000 /* DENALI_CTL_146_DATA */
+ 0x00000000 /* DENALI_CTL_147_DATA */
+ 0x00000000 /* DENALI_CTL_148_DATA */
+ 0x00000000 /* DENALI_CTL_149_DATA */
+ 0x00000000 /* DENALI_CTL_150_DATA */
+ 0x00000000 /* DENALI_CTL_151_DATA */
+ 0x00000000 /* DENALI_CTL_152_DATA */
+ 0x00000000 /* DENALI_CTL_153_DATA */
+ 0x00000000 /* DENALI_CTL_154_DATA */
+ 0x00000000 /* DENALI_CTL_155_DATA */
+ 0x00000000 /* DENALI_CTL_156_DATA */
+ 0x00000000 /* DENALI_CTL_157_DATA */
+ 0x00000000 /* DENALI_CTL_158_DATA */
+ 0x00000000 /* DENALI_CTL_159_DATA */
+ 0x00000000 /* DENALI_CTL_160_DATA */
+ 0x02010102 /* DENALI_CTL_161_DATA */
+ 0x0107070d /* DENALI_CTL_162_DATA */
+ 0x04040400 /* DENALI_CTL_163_DATA */
+ 0x03000503 /* DENALI_CTL_164_DATA */
+ 0x00000000 /* DENALI_CTL_165_DATA */
+ 0x00000000 /* DENALI_CTL_166_DATA */
+ 0x00000000 /* DENALI_CTL_167_DATA */
+ 0x00000000 /* DENALI_CTL_168_DATA */
+ 0x280d0000 /* DENALI_CTL_169_DATA */
+ 0x01000000 /* DENALI_CTL_170_DATA */
+ 0x00000000 /* DENALI_CTL_171_DATA */
+ 0x00010001 /* DENALI_CTL_172_DATA */
+ 0x00000000 /* DENALI_CTL_173_DATA */
+ 0x00000000 /* DENALI_CTL_174_DATA */
+ 0x00000000 /* DENALI_CTL_175_DATA */
+ 0x00000000 /* DENALI_CTL_176_DATA */
+ 0x00000000 /* DENALI_CTL_177_DATA */
+ 0x00000000 /* DENALI_CTL_178_DATA */
+ 0x00000000 /* DENALI_CTL_179_DATA */
+ 0x00000000 /* DENALI_CTL_180_DATA */
+ 0x01000000 /* DENALI_CTL_181_DATA */
+ 0x00000001 /* DENALI_CTL_182_DATA */
+ 0x00000100 /* DENALI_CTL_183_DATA */
+ 0x00000101 /* DENALI_CTL_184_DATA */
+ 0x67676701 /* DENALI_CTL_185_DATA */
+ 0x67676767 /* DENALI_CTL_186_DATA */
+ 0x67676767 /* DENALI_CTL_187_DATA */
+ 0x67676767 /* DENALI_CTL_188_DATA */
+ 0x67676767 /* DENALI_CTL_189_DATA */
+ 0x67676767 /* DENALI_CTL_190_DATA */
+ 0x67676767 /* DENALI_CTL_191_DATA */
+ 0x67676767 /* DENALI_CTL_192_DATA */
+ 0x67676767 /* DENALI_CTL_193_DATA */
+ 0x01000067 /* DENALI_CTL_194_DATA */
+ 0x00000001 /* DENALI_CTL_195_DATA */
+ 0x00000101 /* DENALI_CTL_196_DATA */
+ 0x00000000 /* DENALI_CTL_197_DATA */
+ 0x00000000 /* DENALI_CTL_198_DATA */
+ 0x00000000 /* DENALI_CTL_199_DATA */
+ 0x00000000 /* DENALI_CTL_200_DATA */
+ 0x00000000 /* DENALI_CTL_201_DATA */
+ 0x00000000 /* DENALI_CTL_202_DATA */
+ 0x00000000 /* DENALI_CTL_203_DATA */
+ 0x00000000 /* DENALI_CTL_204_DATA */
+ 0x00000000 /* DENALI_CTL_205_DATA */
+ 0x00000000 /* DENALI_CTL_206_DATA */
+ 0x00000000 /* DENALI_CTL_207_DATA */
+ 0x00000001 /* DENALI_CTL_208_DATA */
+ 0x00000000 /* DENALI_CTL_209_DATA */
+ 0x007fffff /* DENALI_CTL_210_DATA */
+ 0x00000000 /* DENALI_CTL_211_DATA */
+ 0x007fffff /* DENALI_CTL_212_DATA */
+ 0x00000000 /* DENALI_CTL_213_DATA */
+ 0x007fffff /* DENALI_CTL_214_DATA */
+ 0x00000000 /* DENALI_CTL_215_DATA */
+ 0x007fffff /* DENALI_CTL_216_DATA */
+ 0x00000000 /* DENALI_CTL_217_DATA */
+ 0x007fffff /* DENALI_CTL_218_DATA */
+ 0x00000000 /* DENALI_CTL_219_DATA */
+ 0x007fffff /* DENALI_CTL_220_DATA */
+ 0x00000000 /* DENALI_CTL_221_DATA */
+ 0x007fffff /* DENALI_CTL_222_DATA */
+ 0x00000000 /* DENALI_CTL_223_DATA */
+ 0x037fffff /* DENALI_CTL_224_DATA */
+ 0xffffffff /* DENALI_CTL_225_DATA */
+ 0x000f000f /* DENALI_CTL_226_DATA */
+ 0x00ffff03 /* DENALI_CTL_227_DATA */
+ 0x000fffff /* DENALI_CTL_228_DATA */
+ 0x0003000f /* DENALI_CTL_229_DATA */
+ 0xffffffff /* DENALI_CTL_230_DATA */
+ 0x000f000f /* DENALI_CTL_231_DATA */
+ 0x00ffff03 /* DENALI_CTL_232_DATA */
+ 0x000fffff /* DENALI_CTL_233_DATA */
+ 0x0003000f /* DENALI_CTL_234_DATA */
+ 0xffffffff /* DENALI_CTL_235_DATA */
+ 0x000f000f /* DENALI_CTL_236_DATA */
+ 0x00ffff03 /* DENALI_CTL_237_DATA */
+ 0x000fffff /* DENALI_CTL_238_DATA */
+ 0x0003000f /* DENALI_CTL_239_DATA */
+ 0xffffffff /* DENALI_CTL_240_DATA */
+ 0x000f000f /* DENALI_CTL_241_DATA */
+ 0x00ffff03 /* DENALI_CTL_242_DATA */
+ 0x000fffff /* DENALI_CTL_243_DATA */
+ 0x6407000f /* DENALI_CTL_244_DATA */
+ 0x01640001 /* DENALI_CTL_245_DATA */
+ 0x00000000 /* DENALI_CTL_246_DATA */
+ 0x00000000 /* DENALI_CTL_247_DATA */
+ 0x00001700 /* DENALI_CTL_248_DATA */
+ 0x00386c05 /* DENALI_CTL_249_DATA */
+ 0x02000200 /* DENALI_CTL_250_DATA */
+ 0x02000200 /* DENALI_CTL_251_DATA */
+ 0x0000386c /* DENALI_CTL_252_DATA */
+ 0x00023438 /* DENALI_CTL_253_DATA */
+ 0x02020d10 /* DENALI_CTL_254_DATA */
+ 0x00140303 /* DENALI_CTL_255_DATA */
+ 0x00000000 /* DENALI_CTL_256_DATA */
+ 0x00000000 /* DENALI_CTL_257_DATA */
+ 0x00001403 /* DENALI_CTL_258_DATA */
+ 0x00000000 /* DENALI_CTL_259_DATA */
+ 0x00000000 /* DENALI_CTL_260_DATA */
+ 0x00000000 /* DENALI_CTL_261_DATA */
+ 0x00000000 /* DENALI_CTL_262_DATA */
+ 0x0d010000 /* DENALI_CTL_263_DATA */
+ 0x00000008 /* DENALI_CTL_264_DATA */
+ 0x31706542 /* DENALI_PHY_00_DATA */
+ 0x0004c008 /* DENALI_PHY_01_DATA */
+ 0x000000da /* DENALI_PHY_02_DATA */
+ 0x00000000 /* DENALI_PHY_03_DATA */
+ 0x00000000 /* DENALI_PHY_04_DATA */
+ 0x00010000 /* DENALI_PHY_05_DATA */
+ 0x01DDDD90 /* DENALI_PHY_06_DATA */
+ 0x01DDDD90 /* DENALI_PHY_07_DATA */
+ 0x01030000 /* DENALI_PHY_08_DATA */
+ 0x01000000 /* DENALI_PHY_09_DATA */
+ 0x00c00000 /* DENALI_PHY_10_DATA */
+ 0x00000007 /* DENALI_PHY_11_DATA */
+ 0x00000000 /* DENALI_PHY_12_DATA */
+ 0x00000000 /* DENALI_PHY_13_DATA */
+ 0x04000408 /* DENALI_PHY_14_DATA */
+ 0x00000408 /* DENALI_PHY_15_DATA */
+ 0x00e4e400 /* DENALI_PHY_16_DATA */
+ 0x00000000 /* DENALI_PHY_17_DATA */
+ 0x00000000 /* DENALI_PHY_18_DATA */
+ 0x00000000 /* DENALI_PHY_19_DATA */
+ 0x00000000 /* DENALI_PHY_20_DATA */
+ 0x00000000 /* DENALI_PHY_21_DATA */
+ 0x00000000 /* DENALI_PHY_22_DATA */
+ 0x00000000 /* DENALI_PHY_23_DATA */
+ 0x00000000 /* DENALI_PHY_24_DATA */
+ 0x00000000 /* DENALI_PHY_25_DATA */
+ 0x00000000 /* DENALI_PHY_26_DATA */
+ 0x00000000 /* DENALI_PHY_27_DATA */
+ 0x00000000 /* DENALI_PHY_28_DATA */
+ 0x00000000 /* DENALI_PHY_29_DATA */
+ 0x00000000 /* DENALI_PHY_30_DATA */
+ 0x00000000 /* DENALI_PHY_31_DATA */
+ 0x00000000 /* DENALI_PHY_32_DATA */
+ 0x00200000 /* DENALI_PHY_33_DATA */
+ 0x00000000 /* DENALI_PHY_34_DATA */
+ 0x00000000 /* DENALI_PHY_35_DATA */
+ 0x00000000 /* DENALI_PHY_36_DATA */
+ 0x00000000 /* DENALI_PHY_37_DATA */
+ 0x00000000 /* DENALI_PHY_38_DATA */
+ 0x00000000 /* DENALI_PHY_39_DATA */
+ 0x02800280 /* DENALI_PHY_40_DATA */
+ 0x02800280 /* DENALI_PHY_41_DATA */
+ 0x02800280 /* DENALI_PHY_42_DATA */
+ 0x02800280 /* DENALI_PHY_43_DATA */
+ 0x00000280 /* DENALI_PHY_44_DATA */
+ 0x00000000 /* DENALI_PHY_45_DATA */
+ 0x00000000 /* DENALI_PHY_46_DATA */
+ 0x00000000 /* DENALI_PHY_47_DATA */
+ 0x00000000 /* DENALI_PHY_48_DATA */
+ 0x00000000 /* DENALI_PHY_49_DATA */
+ 0x00800080 /* DENALI_PHY_50_DATA */
+ 0x00800080 /* DENALI_PHY_51_DATA */
+ 0x00800080 /* DENALI_PHY_52_DATA */
+ 0x00800080 /* DENALI_PHY_53_DATA */
+ 0x00800080 /* DENALI_PHY_54_DATA */
+ 0x00800080 /* DENALI_PHY_55_DATA */
+ 0x00800080 /* DENALI_PHY_56_DATA */
+ 0x00800080 /* DENALI_PHY_57_DATA */
+ 0x00800080 /* DENALI_PHY_58_DATA */
+ 0x000100da /* DENALI_PHY_59_DATA */
+ 0x01000200 /* DENALI_PHY_60_DATA */
+ 0x00000000 /* DENALI_PHY_61_DATA */
+ 0x00000000 /* DENALI_PHY_62_DATA */
+ 0x00000002 /* DENALI_PHY_63_DATA */
+ 0x51313152 /* DENALI_PHY_64_DATA */
+ 0x80013130 /* DENALI_PHY_65_DATA */
+ 0x02000080 /* DENALI_PHY_66_DATA */
+ 0x00100001 /* DENALI_PHY_67_DATA */
+ 0x0c064208 /* DENALI_PHY_68_DATA */
+ 0x000f0c0f /* DENALI_PHY_69_DATA */
+ 0x01000140 /* DENALI_PHY_70_DATA */
+ 0x0000000c /* DENALI_PHY_71_DATA */
+ 0x00000000 /* DENALI_PHY_72_DATA */
+ 0x00000000 /* DENALI_PHY_73_DATA */
+ 0x00000000 /* DENALI_PHY_74_DATA */
+ 0x00000000 /* DENALI_PHY_75_DATA */
+ 0x00000000 /* DENALI_PHY_76_DATA */
+ 0x00000000 /* DENALI_PHY_77_DATA */
+ 0x00000000 /* DENALI_PHY_78_DATA */
+ 0x00000000 /* DENALI_PHY_79_DATA */
+ 0x00000000 /* DENALI_PHY_80_DATA */
+ 0x00000000 /* DENALI_PHY_81_DATA */
+ 0x00000000 /* DENALI_PHY_82_DATA */
+ 0x00000000 /* DENALI_PHY_83_DATA */
+ 0x00000000 /* DENALI_PHY_84_DATA */
+ 0x00000000 /* DENALI_PHY_85_DATA */
+ 0x00000000 /* DENALI_PHY_86_DATA */
+ 0x00000000 /* DENALI_PHY_87_DATA */
+ 0x00000000 /* DENALI_PHY_88_DATA */
+ 0x00000000 /* DENALI_PHY_89_DATA */
+ 0x00000000 /* DENALI_PHY_90_DATA */
+ 0x00000000 /* DENALI_PHY_91_DATA */
+ 0x00000000 /* DENALI_PHY_92_DATA */
+ 0x00000000 /* DENALI_PHY_93_DATA */
+ 0x00000000 /* DENALI_PHY_94_DATA */
+ 0x00000000 /* DENALI_PHY_95_DATA */
+ 0x00000000 /* DENALI_PHY_96_DATA */
+ 0x00000000 /* DENALI_PHY_97_DATA */
+ 0x00000000 /* DENALI_PHY_98_DATA */
+ 0x00000000 /* DENALI_PHY_99_DATA */
+ 0x00000000 /* DENALI_PHY_100_DATA */
+ 0x00000000 /* DENALI_PHY_101_DATA */
+ 0x00000000 /* DENALI_PHY_102_DATA */
+ 0x00000000 /* DENALI_PHY_103_DATA */
+ 0x00000000 /* DENALI_PHY_104_DATA */
+ 0x00000000 /* DENALI_PHY_105_DATA */
+ 0x00000000 /* DENALI_PHY_106_DATA */
+ 0x00000000 /* DENALI_PHY_107_DATA */
+ 0x00000000 /* DENALI_PHY_108_DATA */
+ 0x00000000 /* DENALI_PHY_109_DATA */
+ 0x00000000 /* DENALI_PHY_110_DATA */
+ 0x00000000 /* DENALI_PHY_111_DATA */
+ 0x00000000 /* DENALI_PHY_112_DATA */
+ 0x00000000 /* DENALI_PHY_113_DATA */
+ 0x00000000 /* DENALI_PHY_114_DATA */
+ 0x00000000 /* DENALI_PHY_115_DATA */
+ 0x00000000 /* DENALI_PHY_116_DATA */
+ 0x00000000 /* DENALI_PHY_117_DATA */
+ 0x00000000 /* DENALI_PHY_118_DATA */
+ 0x00000000 /* DENALI_PHY_119_DATA */
+ 0x00000000 /* DENALI_PHY_120_DATA */
+ 0x00000000 /* DENALI_PHY_121_DATA */
+ 0x00000000 /* DENALI_PHY_122_DATA */
+ 0x00000000 /* DENALI_PHY_123_DATA */
+ 0x00000000 /* DENALI_PHY_124_DATA */
+ 0x00000000 /* DENALI_PHY_125_DATA */
+ 0x00000000 /* DENALI_PHY_126_DATA */
+ 0x00000000 /* DENALI_PHY_127_DATA */
+ 0x40263571 /* DENALI_PHY_128_DATA */
+ 0x0004c008 /* DENALI_PHY_129_DATA */
+ 0x000000da /* DENALI_PHY_130_DATA */
+ 0x00000000 /* DENALI_PHY_131_DATA */
+ 0x00000000 /* DENALI_PHY_132_DATA */
+ 0x00010000 /* DENALI_PHY_133_DATA */
+ 0x01DDDD90 /* DENALI_PHY_134_DATA */
+ 0x01DDDD90 /* DENALI_PHY_135_DATA */
+ 0x01030000 /* DENALI_PHY_136_DATA */
+ 0x01000000 /* DENALI_PHY_137_DATA */
+ 0x00c00000 /* DENALI_PHY_138_DATA */
+ 0x00000007 /* DENALI_PHY_139_DATA */
+ 0x00000000 /* DENALI_PHY_140_DATA */
+ 0x00000000 /* DENALI_PHY_141_DATA */
+ 0x04000408 /* DENALI_PHY_142_DATA */
+ 0x00000408 /* DENALI_PHY_143_DATA */
+ 0x00e4e400 /* DENALI_PHY_144_DATA */
+ 0x00000000 /* DENALI_PHY_145_DATA */
+ 0x00000000 /* DENALI_PHY_146_DATA */
+ 0x00000000 /* DENALI_PHY_147_DATA */
+ 0x00000000 /* DENALI_PHY_148_DATA */
+ 0x00000000 /* DENALI_PHY_149_DATA */
+ 0x00000000 /* DENALI_PHY_150_DATA */
+ 0x00000000 /* DENALI_PHY_151_DATA */
+ 0x00000000 /* DENALI_PHY_152_DATA */
+ 0x00000000 /* DENALI_PHY_153_DATA */
+ 0x00000000 /* DENALI_PHY_154_DATA */
+ 0x00000000 /* DENALI_PHY_155_DATA */
+ 0x00000000 /* DENALI_PHY_156_DATA */
+ 0x00000000 /* DENALI_PHY_157_DATA */
+ 0x00000000 /* DENALI_PHY_158_DATA */
+ 0x00000000 /* DENALI_PHY_159_DATA */
+ 0x00000000 /* DENALI_PHY_160_DATA */
+ 0x00200000 /* DENALI_PHY_161_DATA */
+ 0x00000000 /* DENALI_PHY_162_DATA */
+ 0x00000000 /* DENALI_PHY_163_DATA */
+ 0x00000000 /* DENALI_PHY_164_DATA */
+ 0x00000000 /* DENALI_PHY_165_DATA */
+ 0x00000000 /* DENALI_PHY_166_DATA */
+ 0x00000000 /* DENALI_PHY_167_DATA */
+ 0x02800280 /* DENALI_PHY_168_DATA */
+ 0x02800280 /* DENALI_PHY_169_DATA */
+ 0x02800280 /* DENALI_PHY_170_DATA */
+ 0x02800280 /* DENALI_PHY_171_DATA */
+ 0x00000280 /* DENALI_PHY_172_DATA */
+ 0x00000000 /* DENALI_PHY_173_DATA */
+ 0x00000000 /* DENALI_PHY_174_DATA */
+ 0x00000000 /* DENALI_PHY_175_DATA */
+ 0x00000000 /* DENALI_PHY_176_DATA */
+ 0x00000000 /* DENALI_PHY_177_DATA */
+ 0x00800080 /* DENALI_PHY_178_DATA */
+ 0x00800080 /* DENALI_PHY_179_DATA */
+ 0x00800080 /* DENALI_PHY_180_DATA */
+ 0x00800080 /* DENALI_PHY_181_DATA */
+ 0x00800080 /* DENALI_PHY_182_DATA */
+ 0x00800080 /* DENALI_PHY_183_DATA */
+ 0x00800080 /* DENALI_PHY_184_DATA */
+ 0x00800080 /* DENALI_PHY_185_DATA */
+ 0x00800080 /* DENALI_PHY_186_DATA */
+ 0x000100da /* DENALI_PHY_187_DATA */
+ 0x01000200 /* DENALI_PHY_188_DATA */
+ 0x00000000 /* DENALI_PHY_189_DATA */
+ 0x00000000 /* DENALI_PHY_190_DATA */
+ 0x00000002 /* DENALI_PHY_191_DATA */
+ 0x51313152 /* DENALI_PHY_192_DATA */
+ 0x80013130 /* DENALI_PHY_193_DATA */
+ 0x02000080 /* DENALI_PHY_194_DATA */
+ 0x00100001 /* DENALI_PHY_195_DATA */
+ 0x0c064208 /* DENALI_PHY_196_DATA */
+ 0x000f0c0f /* DENALI_PHY_197_DATA */
+ 0x01000140 /* DENALI_PHY_198_DATA */
+ 0x0000000c /* DENALI_PHY_199_DATA */
+ 0x00000000 /* DENALI_PHY_200_DATA */
+ 0x00000000 /* DENALI_PHY_201_DATA */
+ 0x00000000 /* DENALI_PHY_202_DATA */
+ 0x00000000 /* DENALI_PHY_203_DATA */
+ 0x00000000 /* DENALI_PHY_204_DATA */
+ 0x00000000 /* DENALI_PHY_205_DATA */
+ 0x00000000 /* DENALI_PHY_206_DATA */
+ 0x00000000 /* DENALI_PHY_207_DATA */
+ 0x00000000 /* DENALI_PHY_208_DATA */
+ 0x00000000 /* DENALI_PHY_209_DATA */
+ 0x00000000 /* DENALI_PHY_210_DATA */
+ 0x00000000 /* DENALI_PHY_211_DATA */
+ 0x00000000 /* DENALI_PHY_212_DATA */
+ 0x00000000 /* DENALI_PHY_213_DATA */
+ 0x00000000 /* DENALI_PHY_214_DATA */
+ 0x00000000 /* DENALI_PHY_215_DATA */
+ 0x00000000 /* DENALI_PHY_216_DATA */
+ 0x00000000 /* DENALI_PHY_217_DATA */
+ 0x00000000 /* DENALI_PHY_218_DATA */
+ 0x00000000 /* DENALI_PHY_219_DATA */
+ 0x00000000 /* DENALI_PHY_220_DATA */
+ 0x00000000 /* DENALI_PHY_221_DATA */
+ 0x00000000 /* DENALI_PHY_222_DATA */
+ 0x00000000 /* DENALI_PHY_223_DATA */
+ 0x00000000 /* DENALI_PHY_224_DATA */
+ 0x00000000 /* DENALI_PHY_225_DATA */
+ 0x00000000 /* DENALI_PHY_226_DATA */
+ 0x00000000 /* DENALI_PHY_227_DATA */
+ 0x00000000 /* DENALI_PHY_228_DATA */
+ 0x00000000 /* DENALI_PHY_229_DATA */
+ 0x00000000 /* DENALI_PHY_230_DATA */
+ 0x00000000 /* DENALI_PHY_231_DATA */
+ 0x00000000 /* DENALI_PHY_232_DATA */
+ 0x00000000 /* DENALI_PHY_233_DATA */
+ 0x00000000 /* DENALI_PHY_234_DATA */
+ 0x00000000 /* DENALI_PHY_235_DATA */
+ 0x00000000 /* DENALI_PHY_236_DATA */
+ 0x00000000 /* DENALI_PHY_237_DATA */
+ 0x00000000 /* DENALI_PHY_238_DATA */
+ 0x00000000 /* DENALI_PHY_239_DATA */
+ 0x00000000 /* DENALI_PHY_240_DATA */
+ 0x00000000 /* DENALI_PHY_241_DATA */
+ 0x00000000 /* DENALI_PHY_242_DATA */
+ 0x00000000 /* DENALI_PHY_243_DATA */
+ 0x00000000 /* DENALI_PHY_244_DATA */
+ 0x00000000 /* DENALI_PHY_245_DATA */
+ 0x00000000 /* DENALI_PHY_246_DATA */
+ 0x00000000 /* DENALI_PHY_247_DATA */
+ 0x00000000 /* DENALI_PHY_248_DATA */
+ 0x00000000 /* DENALI_PHY_249_DATA */
+ 0x00000000 /* DENALI_PHY_250_DATA */
+ 0x00000000 /* DENALI_PHY_251_DATA */
+ 0x00000000 /* DENALI_PHY_252_DATA */
+ 0x00000000 /* DENALI_PHY_253_DATA */
+ 0x00000000 /* DENALI_PHY_254_DATA */
+ 0x00000000 /* DENALI_PHY_255_DATA */
+ 0x46052371 /* DENALI_PHY_256_DATA */
+ 0x0004c008 /* DENALI_PHY_257_DATA */
+ 0x000000da /* DENALI_PHY_258_DATA */
+ 0x00000000 /* DENALI_PHY_259_DATA */
+ 0x00000000 /* DENALI_PHY_260_DATA */
+ 0x00010000 /* DENALI_PHY_261_DATA */
+ 0x01DDDD90 /* DENALI_PHY_262_DATA */
+ 0x01DDDD90 /* DENALI_PHY_263_DATA */
+ 0x01030000 /* DENALI_PHY_264_DATA */
+ 0x01000000 /* DENALI_PHY_265_DATA */
+ 0x00c00000 /* DENALI_PHY_266_DATA */
+ 0x00000007 /* DENALI_PHY_267_DATA */
+ 0x00000000 /* DENALI_PHY_268_DATA */
+ 0x00000000 /* DENALI_PHY_269_DATA */
+ 0x04000408 /* DENALI_PHY_270_DATA */
+ 0x00000408 /* DENALI_PHY_271_DATA */
+ 0x00e4e400 /* DENALI_PHY_272_DATA */
+ 0x00000000 /* DENALI_PHY_273_DATA */
+ 0x00000000 /* DENALI_PHY_274_DATA */
+ 0x00000000 /* DENALI_PHY_275_DATA */
+ 0x00000000 /* DENALI_PHY_276_DATA */
+ 0x00000000 /* DENALI_PHY_277_DATA */
+ 0x00000000 /* DENALI_PHY_278_DATA */
+ 0x00000000 /* DENALI_PHY_279_DATA */
+ 0x00000000 /* DENALI_PHY_280_DATA */
+ 0x00000000 /* DENALI_PHY_281_DATA */
+ 0x00000000 /* DENALI_PHY_282_DATA */
+ 0x00000000 /* DENALI_PHY_283_DATA */
+ 0x00000000 /* DENALI_PHY_284_DATA */
+ 0x00000000 /* DENALI_PHY_285_DATA */
+ 0x00000000 /* DENALI_PHY_286_DATA */
+ 0x00000000 /* DENALI_PHY_287_DATA */
+ 0x00000000 /* DENALI_PHY_288_DATA */
+ 0x00200000 /* DENALI_PHY_289_DATA */
+ 0x00000000 /* DENALI_PHY_290_DATA */
+ 0x00000000 /* DENALI_PHY_291_DATA */
+ 0x00000000 /* DENALI_PHY_292_DATA */
+ 0x00000000 /* DENALI_PHY_293_DATA */
+ 0x00000000 /* DENALI_PHY_294_DATA */
+ 0x00000000 /* DENALI_PHY_295_DATA */
+ 0x02800280 /* DENALI_PHY_296_DATA */
+ 0x02800280 /* DENALI_PHY_297_DATA */
+ 0x02800280 /* DENALI_PHY_298_DATA */
+ 0x02800280 /* DENALI_PHY_299_DATA */
+ 0x00000280 /* DENALI_PHY_300_DATA */
+ 0x00000000 /* DENALI_PHY_301_DATA */
+ 0x00000000 /* DENALI_PHY_302_DATA */
+ 0x00000000 /* DENALI_PHY_303_DATA */
+ 0x00000000 /* DENALI_PHY_304_DATA */
+ 0x00000000 /* DENALI_PHY_305_DATA */
+ 0x00800080 /* DENALI_PHY_306_DATA */
+ 0x00800080 /* DENALI_PHY_307_DATA */
+ 0x00800080 /* DENALI_PHY_308_DATA */
+ 0x00800080 /* DENALI_PHY_309_DATA */
+ 0x00800080 /* DENALI_PHY_310_DATA */
+ 0x00800080 /* DENALI_PHY_311_DATA */
+ 0x00800080 /* DENALI_PHY_312_DATA */
+ 0x00800080 /* DENALI_PHY_313_DATA */
+ 0x00800080 /* DENALI_PHY_314_DATA */
+ 0x000100da /* DENALI_PHY_315_DATA */
+ 0x00000200 /* DENALI_PHY_316_DATA */
+ 0x00000000 /* DENALI_PHY_317_DATA */
+ 0x00000000 /* DENALI_PHY_318_DATA */
+ 0x00000002 /* DENALI_PHY_319_DATA */
+ 0x51313152 /* DENALI_PHY_320_DATA */
+ 0x80013130 /* DENALI_PHY_321_DATA */
+ 0x02000080 /* DENALI_PHY_322_DATA */
+ 0x00100001 /* DENALI_PHY_323_DATA */
+ 0x0c064208 /* DENALI_PHY_324_DATA */
+ 0x000f0c0f /* DENALI_PHY_325_DATA */
+ 0x01000140 /* DENALI_PHY_326_DATA */
+ 0x0000000c /* DENALI_PHY_327_DATA */
+ 0x00000000 /* DENALI_PHY_328_DATA */
+ 0x00000000 /* DENALI_PHY_329_DATA */
+ 0x00000000 /* DENALI_PHY_330_DATA */
+ 0x00000000 /* DENALI_PHY_331_DATA */
+ 0x00000000 /* DENALI_PHY_332_DATA */
+ 0x00000000 /* DENALI_PHY_333_DATA */
+ 0x00000000 /* DENALI_PHY_334_DATA */
+ 0x00000000 /* DENALI_PHY_335_DATA */
+ 0x00000000 /* DENALI_PHY_336_DATA */
+ 0x00000000 /* DENALI_PHY_337_DATA */
+ 0x00000000 /* DENALI_PHY_338_DATA */
+ 0x00000000 /* DENALI_PHY_339_DATA */
+ 0x00000000 /* DENALI_PHY_340_DATA */
+ 0x00000000 /* DENALI_PHY_341_DATA */
+ 0x00000000 /* DENALI_PHY_342_DATA */
+ 0x00000000 /* DENALI_PHY_343_DATA */
+ 0x00000000 /* DENALI_PHY_344_DATA */
+ 0x00000000 /* DENALI_PHY_345_DATA */
+ 0x00000000 /* DENALI_PHY_346_DATA */
+ 0x00000000 /* DENALI_PHY_347_DATA */
+ 0x00000000 /* DENALI_PHY_348_DATA */
+ 0x00000000 /* DENALI_PHY_349_DATA */
+ 0x00000000 /* DENALI_PHY_350_DATA */
+ 0x00000000 /* DENALI_PHY_351_DATA */
+ 0x00000000 /* DENALI_PHY_352_DATA */
+ 0x00000000 /* DENALI_PHY_353_DATA */
+ 0x00000000 /* DENALI_PHY_354_DATA */
+ 0x00000000 /* DENALI_PHY_355_DATA */
+ 0x00000000 /* DENALI_PHY_356_DATA */
+ 0x00000000 /* DENALI_PHY_357_DATA */
+ 0x00000000 /* DENALI_PHY_358_DATA */
+ 0x00000000 /* DENALI_PHY_359_DATA */
+ 0x00000000 /* DENALI_PHY_360_DATA */
+ 0x00000000 /* DENALI_PHY_361_DATA */
+ 0x00000000 /* DENALI_PHY_362_DATA */
+ 0x00000000 /* DENALI_PHY_363_DATA */
+ 0x00000000 /* DENALI_PHY_364_DATA */
+ 0x00000000 /* DENALI_PHY_365_DATA */
+ 0x00000000 /* DENALI_PHY_366_DATA */
+ 0x00000000 /* DENALI_PHY_367_DATA */
+ 0x00000000 /* DENALI_PHY_368_DATA */
+ 0x00000000 /* DENALI_PHY_369_DATA */
+ 0x00000000 /* DENALI_PHY_370_DATA */
+ 0x00000000 /* DENALI_PHY_371_DATA */
+ 0x00000000 /* DENALI_PHY_372_DATA */
+ 0x00000000 /* DENALI_PHY_373_DATA */
+ 0x00000000 /* DENALI_PHY_374_DATA */
+ 0x00000000 /* DENALI_PHY_375_DATA */
+ 0x00000000 /* DENALI_PHY_376_DATA */
+ 0x00000000 /* DENALI_PHY_377_DATA */
+ 0x00000000 /* DENALI_PHY_378_DATA */
+ 0x00000000 /* DENALI_PHY_379_DATA */
+ 0x00000000 /* DENALI_PHY_380_DATA */
+ 0x00000000 /* DENALI_PHY_381_DATA */
+ 0x00000000 /* DENALI_PHY_382_DATA */
+ 0x00000000 /* DENALI_PHY_383_DATA */
+ 0x37654120 /* DENALI_PHY_384_DATA */
+ 0x0004c008 /* DENALI_PHY_385_DATA */
+ 0x000000da /* DENALI_PHY_386_DATA */
+ 0x00000000 /* DENALI_PHY_387_DATA */
+ 0x00000000 /* DENALI_PHY_388_DATA */
+ 0x00010000 /* DENALI_PHY_389_DATA */
+ 0x01DDDD90 /* DENALI_PHY_390_DATA */
+ 0x01DDDD90 /* DENALI_PHY_391_DATA */
+ 0x01030000 /* DENALI_PHY_392_DATA */
+ 0x01000000 /* DENALI_PHY_393_DATA */
+ 0x00c00000 /* DENALI_PHY_394_DATA */
+ 0x00000007 /* DENALI_PHY_395_DATA */
+ 0x00000000 /* DENALI_PHY_396_DATA */
+ 0x00000000 /* DENALI_PHY_397_DATA */
+ 0x04000408 /* DENALI_PHY_398_DATA */
+ 0x00000408 /* DENALI_PHY_399_DATA */
+ 0x00e4e400 /* DENALI_PHY_400_DATA */
+ 0x00000000 /* DENALI_PHY_401_DATA */
+ 0x00000000 /* DENALI_PHY_402_DATA */
+ 0x00000000 /* DENALI_PHY_403_DATA */
+ 0x00000000 /* DENALI_PHY_404_DATA */
+ 0x00000000 /* DENALI_PHY_405_DATA */
+ 0x00000000 /* DENALI_PHY_406_DATA */
+ 0x00000000 /* DENALI_PHY_407_DATA */
+ 0x00000000 /* DENALI_PHY_408_DATA */
+ 0x00000000 /* DENALI_PHY_409_DATA */
+ 0x00000000 /* DENALI_PHY_410_DATA */
+ 0x00000000 /* DENALI_PHY_411_DATA */
+ 0x00000000 /* DENALI_PHY_412_DATA */
+ 0x00000000 /* DENALI_PHY_413_DATA */
+ 0x00000000 /* DENALI_PHY_414_DATA */
+ 0x00000000 /* DENALI_PHY_415_DATA */
+ 0x00000000 /* DENALI_PHY_416_DATA */
+ 0x00200000 /* DENALI_PHY_417_DATA */
+ 0x00000000 /* DENALI_PHY_418_DATA */
+ 0x00000000 /* DENALI_PHY_419_DATA */
+ 0x00000000 /* DENALI_PHY_420_DATA */
+ 0x00000000 /* DENALI_PHY_421_DATA */
+ 0x00000000 /* DENALI_PHY_422_DATA */
+ 0x00000000 /* DENALI_PHY_423_DATA */
+ 0x02800280 /* DENALI_PHY_424_DATA */
+ 0x02800280 /* DENALI_PHY_425_DATA */
+ 0x02800280 /* DENALI_PHY_426_DATA */
+ 0x02800280 /* DENALI_PHY_427_DATA */
+ 0x00000280 /* DENALI_PHY_428_DATA */
+ 0x00000000 /* DENALI_PHY_429_DATA */
+ 0x00000000 /* DENALI_PHY_430_DATA */
+ 0x00000000 /* DENALI_PHY_431_DATA */
+ 0x00000000 /* DENALI_PHY_432_DATA */
+ 0x00000000 /* DENALI_PHY_433_DATA */
+ 0x00800080 /* DENALI_PHY_434_DATA */
+ 0x00800080 /* DENALI_PHY_435_DATA */
+ 0x00800080 /* DENALI_PHY_436_DATA */
+ 0x00800080 /* DENALI_PHY_437_DATA */
+ 0x00800080 /* DENALI_PHY_438_DATA */
+ 0x00800080 /* DENALI_PHY_439_DATA */
+ 0x00800080 /* DENALI_PHY_440_DATA */
+ 0x00800080 /* DENALI_PHY_441_DATA */
+ 0x00800080 /* DENALI_PHY_442_DATA */
+ 0x000100da /* DENALI_PHY_443_DATA */
+ 0x00000200 /* DENALI_PHY_444_DATA */
+ 0x00000000 /* DENALI_PHY_445_DATA */
+ 0x00000000 /* DENALI_PHY_446_DATA */
+ 0x00000002 /* DENALI_PHY_447_DATA */
+ 0x51313152 /* DENALI_PHY_448_DATA */
+ 0x80013130 /* DENALI_PHY_449_DATA */
+ 0x02000080 /* DENALI_PHY_450_DATA */
+ 0x00100001 /* DENALI_PHY_451_DATA */
+ 0x0c064208 /* DENALI_PHY_452_DATA */
+ 0x000f0c0f /* DENALI_PHY_453_DATA */
+ 0x01000140 /* DENALI_PHY_454_DATA */
+ 0x0000000c /* DENALI_PHY_455_DATA */
+ 0x00000000 /* DENALI_PHY_456_DATA */
+ 0x00000000 /* DENALI_PHY_457_DATA */
+ 0x00000000 /* DENALI_PHY_458_DATA */
+ 0x00000000 /* DENALI_PHY_459_DATA */
+ 0x00000000 /* DENALI_PHY_460_DATA */
+ 0x00000000 /* DENALI_PHY_461_DATA */
+ 0x00000000 /* DENALI_PHY_462_DATA */
+ 0x00000000 /* DENALI_PHY_463_DATA */
+ 0x00000000 /* DENALI_PHY_464_DATA */
+ 0x00000000 /* DENALI_PHY_465_DATA */
+ 0x00000000 /* DENALI_PHY_466_DATA */
+ 0x00000000 /* DENALI_PHY_467_DATA */
+ 0x00000000 /* DENALI_PHY_468_DATA */
+ 0x00000000 /* DENALI_PHY_469_DATA */
+ 0x00000000 /* DENALI_PHY_470_DATA */
+ 0x00000000 /* DENALI_PHY_471_DATA */
+ 0x00000000 /* DENALI_PHY_472_DATA */
+ 0x00000000 /* DENALI_PHY_473_DATA */
+ 0x00000000 /* DENALI_PHY_474_DATA */
+ 0x00000000 /* DENALI_PHY_475_DATA */
+ 0x00000000 /* DENALI_PHY_476_DATA */
+ 0x00000000 /* DENALI_PHY_477_DATA */
+ 0x00000000 /* DENALI_PHY_478_DATA */
+ 0x00000000 /* DENALI_PHY_479_DATA */
+ 0x00000000 /* DENALI_PHY_480_DATA */
+ 0x00000000 /* DENALI_PHY_481_DATA */
+ 0x00000000 /* DENALI_PHY_482_DATA */
+ 0x00000000 /* DENALI_PHY_483_DATA */
+ 0x00000000 /* DENALI_PHY_484_DATA */
+ 0x00000000 /* DENALI_PHY_485_DATA */
+ 0x00000000 /* DENALI_PHY_486_DATA */
+ 0x00000000 /* DENALI_PHY_487_DATA */
+ 0x00000000 /* DENALI_PHY_488_DATA */
+ 0x00000000 /* DENALI_PHY_489_DATA */
+ 0x00000000 /* DENALI_PHY_490_DATA */
+ 0x00000000 /* DENALI_PHY_491_DATA */
+ 0x00000000 /* DENALI_PHY_492_DATA */
+ 0x00000000 /* DENALI_PHY_493_DATA */
+ 0x00000000 /* DENALI_PHY_494_DATA */
+ 0x00000000 /* DENALI_PHY_495_DATA */
+ 0x00000000 /* DENALI_PHY_496_DATA */
+ 0x00000000 /* DENALI_PHY_497_DATA */
+ 0x00000000 /* DENALI_PHY_498_DATA */
+ 0x00000000 /* DENALI_PHY_499_DATA */
+ 0x00000000 /* DENALI_PHY_500_DATA */
+ 0x00000000 /* DENALI_PHY_501_DATA */
+ 0x00000000 /* DENALI_PHY_502_DATA */
+ 0x00000000 /* DENALI_PHY_503_DATA */
+ 0x00000000 /* DENALI_PHY_504_DATA */
+ 0x00000000 /* DENALI_PHY_505_DATA */
+ 0x00000000 /* DENALI_PHY_506_DATA */
+ 0x00000000 /* DENALI_PHY_507_DATA */
+ 0x00000000 /* DENALI_PHY_508_DATA */
+ 0x00000000 /* DENALI_PHY_509_DATA */
+ 0x00000000 /* DENALI_PHY_510_DATA */
+ 0x00000000 /* DENALI_PHY_511_DATA */
+ 0x24316750 /* DENALI_PHY_512_DATA */
+ 0x0004c008 /* DENALI_PHY_513_DATA */
+ 0x000000da /* DENALI_PHY_514_DATA */
+ 0x00000000 /* DENALI_PHY_515_DATA */
+ 0x00000000 /* DENALI_PHY_516_DATA */
+ 0x00010000 /* DENALI_PHY_517_DATA */
+ 0x01DDDD90 /* DENALI_PHY_518_DATA */
+ 0x01DDDD90 /* DENALI_PHY_519_DATA */
+ 0x01030000 /* DENALI_PHY_520_DATA */
+ 0x01000000 /* DENALI_PHY_521_DATA */
+ 0x00c00000 /* DENALI_PHY_522_DATA */
+ 0x00000007 /* DENALI_PHY_523_DATA */
+ 0x00000000 /* DENALI_PHY_524_DATA */
+ 0x00000000 /* DENALI_PHY_525_DATA */
+ 0x04000408 /* DENALI_PHY_526_DATA */
+ 0x00000408 /* DENALI_PHY_527_DATA */
+ 0x00e4e400 /* DENALI_PHY_528_DATA */
+ 0x00000000 /* DENALI_PHY_529_DATA */
+ 0x00000000 /* DENALI_PHY_530_DATA */
+ 0x00000000 /* DENALI_PHY_531_DATA */
+ 0x00000000 /* DENALI_PHY_532_DATA */
+ 0x00000000 /* DENALI_PHY_533_DATA */
+ 0x00000000 /* DENALI_PHY_534_DATA */
+ 0x00000000 /* DENALI_PHY_535_DATA */
+ 0x00000000 /* DENALI_PHY_536_DATA */
+ 0x00000000 /* DENALI_PHY_537_DATA */
+ 0x00000000 /* DENALI_PHY_538_DATA */
+ 0x00000000 /* DENALI_PHY_539_DATA */
+ 0x00000000 /* DENALI_PHY_540_DATA */
+ 0x00000000 /* DENALI_PHY_541_DATA */
+ 0x00000000 /* DENALI_PHY_542_DATA */
+ 0x00000000 /* DENALI_PHY_543_DATA */
+ 0x00000000 /* DENALI_PHY_544_DATA */
+ 0x00200000 /* DENALI_PHY_545_DATA */
+ 0x00000000 /* DENALI_PHY_546_DATA */
+ 0x00000000 /* DENALI_PHY_547_DATA */
+ 0x00000000 /* DENALI_PHY_548_DATA */
+ 0x00000000 /* DENALI_PHY_549_DATA */
+ 0x00000000 /* DENALI_PHY_550_DATA */
+ 0x00000000 /* DENALI_PHY_551_DATA */
+ 0x02800280 /* DENALI_PHY_552_DATA */
+ 0x02800280 /* DENALI_PHY_553_DATA */
+ 0x02800280 /* DENALI_PHY_554_DATA */
+ 0x02800280 /* DENALI_PHY_555_DATA */
+ 0x00000280 /* DENALI_PHY_556_DATA */
+ 0x00000000 /* DENALI_PHY_557_DATA */
+ 0x00000000 /* DENALI_PHY_558_DATA */
+ 0x00000000 /* DENALI_PHY_559_DATA */
+ 0x00000000 /* DENALI_PHY_560_DATA */
+ 0x00000000 /* DENALI_PHY_561_DATA */
+ 0x00800080 /* DENALI_PHY_562_DATA */
+ 0x00800080 /* DENALI_PHY_563_DATA */
+ 0x00800080 /* DENALI_PHY_564_DATA */
+ 0x00800080 /* DENALI_PHY_565_DATA */
+ 0x00800080 /* DENALI_PHY_566_DATA */
+ 0x00800080 /* DENALI_PHY_567_DATA */
+ 0x00800080 /* DENALI_PHY_568_DATA */
+ 0x00800080 /* DENALI_PHY_569_DATA */
+ 0x00800080 /* DENALI_PHY_570_DATA */
+ 0x000100da /* DENALI_PHY_571_DATA */
+ 0x00000200 /* DENALI_PHY_572_DATA */
+ 0x00000000 /* DENALI_PHY_573_DATA */
+ 0x00000000 /* DENALI_PHY_574_DATA */
+ 0x00000002 /* DENALI_PHY_575_DATA */
+ 0x51313152 /* DENALI_PHY_576_DATA */
+ 0x80013130 /* DENALI_PHY_577_DATA */
+ 0x02000080 /* DENALI_PHY_578_DATA */
+ 0x00100001 /* DENALI_PHY_579_DATA */
+ 0x0c064208 /* DENALI_PHY_580_DATA */
+ 0x000f0c0f /* DENALI_PHY_581_DATA */
+ 0x01000140 /* DENALI_PHY_582_DATA */
+ 0x0000000c /* DENALI_PHY_583_DATA */
+ 0x00000000 /* DENALI_PHY_584_DATA */
+ 0x00000000 /* DENALI_PHY_585_DATA */
+ 0x00000000 /* DENALI_PHY_586_DATA */
+ 0x00000000 /* DENALI_PHY_587_DATA */
+ 0x00000000 /* DENALI_PHY_588_DATA */
+ 0x00000000 /* DENALI_PHY_589_DATA */
+ 0x00000000 /* DENALI_PHY_590_DATA */
+ 0x00000000 /* DENALI_PHY_591_DATA */
+ 0x00000000 /* DENALI_PHY_592_DATA */
+ 0x00000000 /* DENALI_PHY_593_DATA */
+ 0x00000000 /* DENALI_PHY_594_DATA */
+ 0x00000000 /* DENALI_PHY_595_DATA */
+ 0x00000000 /* DENALI_PHY_596_DATA */
+ 0x00000000 /* DENALI_PHY_597_DATA */
+ 0x00000000 /* DENALI_PHY_598_DATA */
+ 0x00000000 /* DENALI_PHY_599_DATA */
+ 0x00000000 /* DENALI_PHY_600_DATA */
+ 0x00000000 /* DENALI_PHY_601_DATA */
+ 0x00000000 /* DENALI_PHY_602_DATA */
+ 0x00000000 /* DENALI_PHY_603_DATA */
+ 0x00000000 /* DENALI_PHY_604_DATA */
+ 0x00000000 /* DENALI_PHY_605_DATA */
+ 0x00000000 /* DENALI_PHY_606_DATA */
+ 0x00000000 /* DENALI_PHY_607_DATA */
+ 0x00000000 /* DENALI_PHY_608_DATA */
+ 0x00000000 /* DENALI_PHY_609_DATA */
+ 0x00000000 /* DENALI_PHY_610_DATA */
+ 0x00000000 /* DENALI_PHY_611_DATA */
+ 0x00000000 /* DENALI_PHY_612_DATA */
+ 0x00000000 /* DENALI_PHY_613_DATA */
+ 0x00000000 /* DENALI_PHY_614_DATA */
+ 0x00000000 /* DENALI_PHY_615_DATA */
+ 0x00000000 /* DENALI_PHY_616_DATA */
+ 0x00000000 /* DENALI_PHY_617_DATA */
+ 0x00000000 /* DENALI_PHY_618_DATA */
+ 0x00000000 /* DENALI_PHY_619_DATA */
+ 0x00000000 /* DENALI_PHY_620_DATA */
+ 0x00000000 /* DENALI_PHY_621_DATA */
+ 0x00000000 /* DENALI_PHY_622_DATA */
+ 0x00000000 /* DENALI_PHY_623_DATA */
+ 0x00000000 /* DENALI_PHY_624_DATA */
+ 0x00000000 /* DENALI_PHY_625_DATA */
+ 0x00000000 /* DENALI_PHY_626_DATA */
+ 0x00000000 /* DENALI_PHY_627_DATA */
+ 0x00000000 /* DENALI_PHY_628_DATA */
+ 0x00000000 /* DENALI_PHY_629_DATA */
+ 0x00000000 /* DENALI_PHY_630_DATA */
+ 0x00000000 /* DENALI_PHY_631_DATA */
+ 0x00000000 /* DENALI_PHY_632_DATA */
+ 0x00000000 /* DENALI_PHY_633_DATA */
+ 0x00000000 /* DENALI_PHY_634_DATA */
+ 0x00000000 /* DENALI_PHY_635_DATA */
+ 0x00000000 /* DENALI_PHY_636_DATA */
+ 0x00000000 /* DENALI_PHY_637_DATA */
+ 0x00000000 /* DENALI_PHY_638_DATA */
+ 0x00000000 /* DENALI_PHY_639_DATA */
+ 0x35174620 /* DENALI_PHY_640_DATA */
+ 0x0004c008 /* DENALI_PHY_641_DATA */
+ 0x000000da /* DENALI_PHY_642_DATA */
+ 0x00000000 /* DENALI_PHY_643_DATA */
+ 0x00000000 /* DENALI_PHY_644_DATA */
+ 0x00010000 /* DENALI_PHY_645_DATA */
+ 0x01DDDD90 /* DENALI_PHY_646_DATA */
+ 0x01DDDD90 /* DENALI_PHY_647_DATA */
+ 0x01030000 /* DENALI_PHY_648_DATA */
+ 0x01000000 /* DENALI_PHY_649_DATA */
+ 0x00c00000 /* DENALI_PHY_650_DATA */
+ 0x00000007 /* DENALI_PHY_651_DATA */
+ 0x00000000 /* DENALI_PHY_652_DATA */
+ 0x00000000 /* DENALI_PHY_653_DATA */
+ 0x04000408 /* DENALI_PHY_654_DATA */
+ 0x00000408 /* DENALI_PHY_655_DATA */
+ 0x00e4e400 /* DENALI_PHY_656_DATA */
+ 0x00000000 /* DENALI_PHY_657_DATA */
+ 0x00000000 /* DENALI_PHY_658_DATA */
+ 0x00000000 /* DENALI_PHY_659_DATA */
+ 0x00000000 /* DENALI_PHY_660_DATA */
+ 0x00000000 /* DENALI_PHY_661_DATA */
+ 0x00000000 /* DENALI_PHY_662_DATA */
+ 0x00000000 /* DENALI_PHY_663_DATA */
+ 0x00000000 /* DENALI_PHY_664_DATA */
+ 0x00000000 /* DENALI_PHY_665_DATA */
+ 0x00000000 /* DENALI_PHY_666_DATA */
+ 0x00000000 /* DENALI_PHY_667_DATA */
+ 0x00000000 /* DENALI_PHY_668_DATA */
+ 0x00000000 /* DENALI_PHY_669_DATA */
+ 0x00000000 /* DENALI_PHY_670_DATA */
+ 0x00000000 /* DENALI_PHY_671_DATA */
+ 0x00000000 /* DENALI_PHY_672_DATA */
+ 0x00200000 /* DENALI_PHY_673_DATA */
+ 0x00000000 /* DENALI_PHY_674_DATA */
+ 0x00000000 /* DENALI_PHY_675_DATA */
+ 0x00000000 /* DENALI_PHY_676_DATA */
+ 0x00000000 /* DENALI_PHY_677_DATA */
+ 0x00000000 /* DENALI_PHY_678_DATA */
+ 0x00000000 /* DENALI_PHY_679_DATA */
+ 0x02800280 /* DENALI_PHY_680_DATA */
+ 0x02800280 /* DENALI_PHY_681_DATA */
+ 0x02800280 /* DENALI_PHY_682_DATA */
+ 0x02800280 /* DENALI_PHY_683_DATA */
+ 0x00000280 /* DENALI_PHY_684_DATA */
+ 0x00000000 /* DENALI_PHY_685_DATA */
+ 0x00000000 /* DENALI_PHY_686_DATA */
+ 0x00000000 /* DENALI_PHY_687_DATA */
+ 0x00000000 /* DENALI_PHY_688_DATA */
+ 0x00000000 /* DENALI_PHY_689_DATA */
+ 0x00800080 /* DENALI_PHY_690_DATA */
+ 0x00800080 /* DENALI_PHY_691_DATA */
+ 0x00800080 /* DENALI_PHY_692_DATA */
+ 0x00800080 /* DENALI_PHY_693_DATA */
+ 0x00800080 /* DENALI_PHY_694_DATA */
+ 0x00800080 /* DENALI_PHY_695_DATA */
+ 0x00800080 /* DENALI_PHY_696_DATA */
+ 0x00800080 /* DENALI_PHY_697_DATA */
+ 0x00800080 /* DENALI_PHY_698_DATA */
+ 0x000100da /* DENALI_PHY_699_DATA */
+ 0x00000200 /* DENALI_PHY_700_DATA */
+ 0x00000000 /* DENALI_PHY_701_DATA */
+ 0x00000000 /* DENALI_PHY_702_DATA */
+ 0x00000002 /* DENALI_PHY_703_DATA */
+ 0x51313152 /* DENALI_PHY_704_DATA */
+ 0x80013130 /* DENALI_PHY_705_DATA */
+ 0x02000080 /* DENALI_PHY_706_DATA */
+ 0x00100001 /* DENALI_PHY_707_DATA */
+ 0x0c064208 /* DENALI_PHY_708_DATA */
+ 0x000f0c0f /* DENALI_PHY_709_DATA */
+ 0x01000140 /* DENALI_PHY_710_DATA */
+ 0x0000000c /* DENALI_PHY_711_DATA */
+ 0x00000000 /* DENALI_PHY_712_DATA */
+ 0x00000000 /* DENALI_PHY_713_DATA */
+ 0x00000000 /* DENALI_PHY_714_DATA */
+ 0x00000000 /* DENALI_PHY_715_DATA */
+ 0x00000000 /* DENALI_PHY_716_DATA */
+ 0x00000000 /* DENALI_PHY_717_DATA */
+ 0x00000000 /* DENALI_PHY_718_DATA */
+ 0x00000000 /* DENALI_PHY_719_DATA */
+ 0x00000000 /* DENALI_PHY_720_DATA */
+ 0x00000000 /* DENALI_PHY_721_DATA */
+ 0x00000000 /* DENALI_PHY_722_DATA */
+ 0x00000000 /* DENALI_PHY_723_DATA */
+ 0x00000000 /* DENALI_PHY_724_DATA */
+ 0x00000000 /* DENALI_PHY_725_DATA */
+ 0x00000000 /* DENALI_PHY_726_DATA */
+ 0x00000000 /* DENALI_PHY_727_DATA */
+ 0x00000000 /* DENALI_PHY_728_DATA */
+ 0x00000000 /* DENALI_PHY_729_DATA */
+ 0x00000000 /* DENALI_PHY_730_DATA */
+ 0x00000000 /* DENALI_PHY_731_DATA */
+ 0x00000000 /* DENALI_PHY_732_DATA */
+ 0x00000000 /* DENALI_PHY_733_DATA */
+ 0x00000000 /* DENALI_PHY_734_DATA */
+ 0x00000000 /* DENALI_PHY_735_DATA */
+ 0x00000000 /* DENALI_PHY_736_DATA */
+ 0x00000000 /* DENALI_PHY_737_DATA */
+ 0x00000000 /* DENALI_PHY_738_DATA */
+ 0x00000000 /* DENALI_PHY_739_DATA */
+ 0x00000000 /* DENALI_PHY_740_DATA */
+ 0x00000000 /* DENALI_PHY_741_DATA */
+ 0x00000000 /* DENALI_PHY_742_DATA */
+ 0x00000000 /* DENALI_PHY_743_DATA */
+ 0x00000000 /* DENALI_PHY_744_DATA */
+ 0x00000000 /* DENALI_PHY_745_DATA */
+ 0x00000000 /* DENALI_PHY_746_DATA */
+ 0x00000000 /* DENALI_PHY_747_DATA */
+ 0x00000000 /* DENALI_PHY_748_DATA */
+ 0x00000000 /* DENALI_PHY_749_DATA */
+ 0x00000000 /* DENALI_PHY_750_DATA */
+ 0x00000000 /* DENALI_PHY_751_DATA */
+ 0x00000000 /* DENALI_PHY_752_DATA */
+ 0x00000000 /* DENALI_PHY_753_DATA */
+ 0x00000000 /* DENALI_PHY_754_DATA */
+ 0x00000000 /* DENALI_PHY_755_DATA */
+ 0x00000000 /* DENALI_PHY_756_DATA */
+ 0x00000000 /* DENALI_PHY_757_DATA */
+ 0x00000000 /* DENALI_PHY_758_DATA */
+ 0x00000000 /* DENALI_PHY_759_DATA */
+ 0x00000000 /* DENALI_PHY_760_DATA */
+ 0x00000000 /* DENALI_PHY_761_DATA */
+ 0x00000000 /* DENALI_PHY_762_DATA */
+ 0x00000000 /* DENALI_PHY_763_DATA */
+ 0x00000000 /* DENALI_PHY_764_DATA */
+ 0x00000000 /* DENALI_PHY_765_DATA */
+ 0x00000000 /* DENALI_PHY_766_DATA */
+ 0x00000000 /* DENALI_PHY_767_DATA */
+ 0x15203476 /* DENALI_PHY_768_DATA */
+ 0x0004c008 /* DENALI_PHY_769_DATA */
+ 0x000000da /* DENALI_PHY_770_DATA */
+ 0x00000000 /* DENALI_PHY_771_DATA */
+ 0x00000000 /* DENALI_PHY_772_DATA */
+ 0x00010000 /* DENALI_PHY_773_DATA */
+ 0x01DDDD90 /* DENALI_PHY_774_DATA */
+ 0x01DDDD90 /* DENALI_PHY_775_DATA */
+ 0x01030000 /* DENALI_PHY_776_DATA */
+ 0x01000000 /* DENALI_PHY_777_DATA */
+ 0x00c00000 /* DENALI_PHY_778_DATA */
+ 0x00000007 /* DENALI_PHY_779_DATA */
+ 0x00000000 /* DENALI_PHY_780_DATA */
+ 0x00000000 /* DENALI_PHY_781_DATA */
+ 0x04000408 /* DENALI_PHY_782_DATA */
+ 0x00000408 /* DENALI_PHY_783_DATA */
+ 0x00e4e400 /* DENALI_PHY_784_DATA */
+ 0x00000000 /* DENALI_PHY_785_DATA */
+ 0x00000000 /* DENALI_PHY_786_DATA */
+ 0x00000000 /* DENALI_PHY_787_DATA */
+ 0x00000000 /* DENALI_PHY_788_DATA */
+ 0x00000000 /* DENALI_PHY_789_DATA */
+ 0x00000000 /* DENALI_PHY_790_DATA */
+ 0x00000000 /* DENALI_PHY_791_DATA */
+ 0x00000000 /* DENALI_PHY_792_DATA */
+ 0x00000000 /* DENALI_PHY_793_DATA */
+ 0x00000000 /* DENALI_PHY_794_DATA */
+ 0x00000000 /* DENALI_PHY_795_DATA */
+ 0x00000000 /* DENALI_PHY_796_DATA */
+ 0x00000000 /* DENALI_PHY_797_DATA */
+ 0x00000000 /* DENALI_PHY_798_DATA */
+ 0x00000000 /* DENALI_PHY_799_DATA */
+ 0x00000000 /* DENALI_PHY_800_DATA */
+ 0x00200000 /* DENALI_PHY_801_DATA */
+ 0x00000000 /* DENALI_PHY_802_DATA */
+ 0x00000000 /* DENALI_PHY_803_DATA */
+ 0x00000000 /* DENALI_PHY_804_DATA */
+ 0x00000000 /* DENALI_PHY_805_DATA */
+ 0x00000000 /* DENALI_PHY_806_DATA */
+ 0x00000000 /* DENALI_PHY_807_DATA */
+ 0x02800280 /* DENALI_PHY_808_DATA */
+ 0x02800280 /* DENALI_PHY_809_DATA */
+ 0x02800280 /* DENALI_PHY_810_DATA */
+ 0x02800280 /* DENALI_PHY_811_DATA */
+ 0x00000280 /* DENALI_PHY_812_DATA */
+ 0x00000000 /* DENALI_PHY_813_DATA */
+ 0x00000000 /* DENALI_PHY_814_DATA */
+ 0x00000000 /* DENALI_PHY_815_DATA */
+ 0x00000000 /* DENALI_PHY_816_DATA */
+ 0x00000000 /* DENALI_PHY_817_DATA */
+ 0x00800080 /* DENALI_PHY_818_DATA */
+ 0x00800080 /* DENALI_PHY_819_DATA */
+ 0x00800080 /* DENALI_PHY_820_DATA */
+ 0x00800080 /* DENALI_PHY_821_DATA */
+ 0x00800080 /* DENALI_PHY_822_DATA */
+ 0x00800080 /* DENALI_PHY_823_DATA */
+ 0x00800080 /* DENALI_PHY_824_DATA */
+ 0x00800080 /* DENALI_PHY_825_DATA */
+ 0x00800080 /* DENALI_PHY_826_DATA */
+ 0x000100da /* DENALI_PHY_827_DATA */
+ 0x00000200 /* DENALI_PHY_828_DATA */
+ 0x00000000 /* DENALI_PHY_829_DATA */
+ 0x00000000 /* DENALI_PHY_830_DATA */
+ 0x00000002 /* DENALI_PHY_831_DATA */
+ 0x51313152 /* DENALI_PHY_832_DATA */
+ 0x80013130 /* DENALI_PHY_833_DATA */
+ 0x02000080 /* DENALI_PHY_834_DATA */
+ 0x00100001 /* DENALI_PHY_835_DATA */
+ 0x0c064208 /* DENALI_PHY_836_DATA */
+ 0x000f0c0f /* DENALI_PHY_837_DATA */
+ 0x01000140 /* DENALI_PHY_838_DATA */
+ 0x0000000c /* DENALI_PHY_839_DATA */
+ 0x00000000 /* DENALI_PHY_840_DATA */
+ 0x00000000 /* DENALI_PHY_841_DATA */
+ 0x00000000 /* DENALI_PHY_842_DATA */
+ 0x00000000 /* DENALI_PHY_843_DATA */
+ 0x00000000 /* DENALI_PHY_844_DATA */
+ 0x00000000 /* DENALI_PHY_845_DATA */
+ 0x00000000 /* DENALI_PHY_846_DATA */
+ 0x00000000 /* DENALI_PHY_847_DATA */
+ 0x00000000 /* DENALI_PHY_848_DATA */
+ 0x00000000 /* DENALI_PHY_849_DATA */
+ 0x00000000 /* DENALI_PHY_850_DATA */
+ 0x00000000 /* DENALI_PHY_851_DATA */
+ 0x00000000 /* DENALI_PHY_852_DATA */
+ 0x00000000 /* DENALI_PHY_853_DATA */
+ 0x00000000 /* DENALI_PHY_854_DATA */
+ 0x00000000 /* DENALI_PHY_855_DATA */
+ 0x00000000 /* DENALI_PHY_856_DATA */
+ 0x00000000 /* DENALI_PHY_857_DATA */
+ 0x00000000 /* DENALI_PHY_858_DATA */
+ 0x00000000 /* DENALI_PHY_859_DATA */
+ 0x00000000 /* DENALI_PHY_860_DATA */
+ 0x00000000 /* DENALI_PHY_861_DATA */
+ 0x00000000 /* DENALI_PHY_862_DATA */
+ 0x00000000 /* DENALI_PHY_863_DATA */
+ 0x00000000 /* DENALI_PHY_864_DATA */
+ 0x00000000 /* DENALI_PHY_865_DATA */
+ 0x00000000 /* DENALI_PHY_866_DATA */
+ 0x00000000 /* DENALI_PHY_867_DATA */
+ 0x00000000 /* DENALI_PHY_868_DATA */
+ 0x00000000 /* DENALI_PHY_869_DATA */
+ 0x00000000 /* DENALI_PHY_870_DATA */
+ 0x00000000 /* DENALI_PHY_871_DATA */
+ 0x00000000 /* DENALI_PHY_872_DATA */
+ 0x00000000 /* DENALI_PHY_873_DATA */
+ 0x00000000 /* DENALI_PHY_874_DATA */
+ 0x00000000 /* DENALI_PHY_875_DATA */
+ 0x00000000 /* DENALI_PHY_876_DATA */
+ 0x00000000 /* DENALI_PHY_877_DATA */
+ 0x00000000 /* DENALI_PHY_878_DATA */
+ 0x00000000 /* DENALI_PHY_879_DATA */
+ 0x00000000 /* DENALI_PHY_880_DATA */
+ 0x00000000 /* DENALI_PHY_881_DATA */
+ 0x00000000 /* DENALI_PHY_882_DATA */
+ 0x00000000 /* DENALI_PHY_883_DATA */
+ 0x00000000 /* DENALI_PHY_884_DATA */
+ 0x00000000 /* DENALI_PHY_885_DATA */
+ 0x00000000 /* DENALI_PHY_886_DATA */
+ 0x00000000 /* DENALI_PHY_887_DATA */
+ 0x00000000 /* DENALI_PHY_888_DATA */
+ 0x00000000 /* DENALI_PHY_889_DATA */
+ 0x00000000 /* DENALI_PHY_890_DATA */
+ 0x00000000 /* DENALI_PHY_891_DATA */
+ 0x00000000 /* DENALI_PHY_892_DATA */
+ 0x00000000 /* DENALI_PHY_893_DATA */
+ 0x00000000 /* DENALI_PHY_894_DATA */
+ 0x00000000 /* DENALI_PHY_895_DATA */
+ 0x41753206 /* DENALI_PHY_896_DATA */
+ 0x0004c008 /* DENALI_PHY_897_DATA */
+ 0x000000da /* DENALI_PHY_898_DATA */
+ 0x00000000 /* DENALI_PHY_899_DATA */
+ 0x00000000 /* DENALI_PHY_900_DATA */
+ 0x00010000 /* DENALI_PHY_901_DATA */
+ 0x01DDDD90 /* DENALI_PHY_902_DATA */
+ 0x01DDDD90 /* DENALI_PHY_903_DATA */
+ 0x01030000 /* DENALI_PHY_904_DATA */
+ 0x01000000 /* DENALI_PHY_905_DATA */
+ 0x00c00000 /* DENALI_PHY_906_DATA */
+ 0x00000007 /* DENALI_PHY_907_DATA */
+ 0x00000000 /* DENALI_PHY_908_DATA */
+ 0x00000000 /* DENALI_PHY_909_DATA */
+ 0x04000408 /* DENALI_PHY_910_DATA */
+ 0x00000408 /* DENALI_PHY_911_DATA */
+ 0x00e4e400 /* DENALI_PHY_912_DATA */
+ 0x00000000 /* DENALI_PHY_913_DATA */
+ 0x00000000 /* DENALI_PHY_914_DATA */
+ 0x00000000 /* DENALI_PHY_915_DATA */
+ 0x00000000 /* DENALI_PHY_916_DATA */
+ 0x00000000 /* DENALI_PHY_917_DATA */
+ 0x00000000 /* DENALI_PHY_918_DATA */
+ 0x00000000 /* DENALI_PHY_919_DATA */
+ 0x00000000 /* DENALI_PHY_920_DATA */
+ 0x00000000 /* DENALI_PHY_921_DATA */
+ 0x00000000 /* DENALI_PHY_922_DATA */
+ 0x00000000 /* DENALI_PHY_923_DATA */
+ 0x00000000 /* DENALI_PHY_924_DATA */
+ 0x00000000 /* DENALI_PHY_925_DATA */
+ 0x00000000 /* DENALI_PHY_926_DATA */
+ 0x00000000 /* DENALI_PHY_927_DATA */
+ 0x00000000 /* DENALI_PHY_928_DATA */
+ 0x00200000 /* DENALI_PHY_929_DATA */
+ 0x00000000 /* DENALI_PHY_930_DATA */
+ 0x00000000 /* DENALI_PHY_931_DATA */
+ 0x00000000 /* DENALI_PHY_932_DATA */
+ 0x00000000 /* DENALI_PHY_933_DATA */
+ 0x00000000 /* DENALI_PHY_934_DATA */
+ 0x00000000 /* DENALI_PHY_935_DATA */
+ 0x02800280 /* DENALI_PHY_936_DATA */
+ 0x02800280 /* DENALI_PHY_937_DATA */
+ 0x02800280 /* DENALI_PHY_938_DATA */
+ 0x02800280 /* DENALI_PHY_939_DATA */
+ 0x00000280 /* DENALI_PHY_940_DATA */
+ 0x00000000 /* DENALI_PHY_941_DATA */
+ 0x00000000 /* DENALI_PHY_942_DATA */
+ 0x00000000 /* DENALI_PHY_943_DATA */
+ 0x00000000 /* DENALI_PHY_944_DATA */
+ 0x00000000 /* DENALI_PHY_945_DATA */
+ 0x00800080 /* DENALI_PHY_946_DATA */
+ 0x00800080 /* DENALI_PHY_947_DATA */
+ 0x00800080 /* DENALI_PHY_948_DATA */
+ 0x00800080 /* DENALI_PHY_949_DATA */
+ 0x00800080 /* DENALI_PHY_950_DATA */
+ 0x00800080 /* DENALI_PHY_951_DATA */
+ 0x00800080 /* DENALI_PHY_952_DATA */
+ 0x00800080 /* DENALI_PHY_953_DATA */
+ 0x00800080 /* DENALI_PHY_954_DATA */
+ 0x000100da /* DENALI_PHY_955_DATA */
+ 0x00000200 /* DENALI_PHY_956_DATA */
+ 0x00000000 /* DENALI_PHY_957_DATA */
+ 0x00000000 /* DENALI_PHY_958_DATA */
+ 0x00000002 /* DENALI_PHY_959_DATA */
+ 0x51313152 /* DENALI_PHY_960_DATA */
+ 0x80013130 /* DENALI_PHY_961_DATA */
+ 0x02000080 /* DENALI_PHY_962_DATA */
+ 0x00100001 /* DENALI_PHY_963_DATA */
+ 0x0c064208 /* DENALI_PHY_964_DATA */
+ 0x000f0c0f /* DENALI_PHY_965_DATA */
+ 0x01000140 /* DENALI_PHY_966_DATA */
+ 0x0000000c /* DENALI_PHY_967_DATA */
+ 0x00000000 /* DENALI_PHY_968_DATA */
+ 0x00000000 /* DENALI_PHY_969_DATA */
+ 0x00000000 /* DENALI_PHY_970_DATA */
+ 0x00000000 /* DENALI_PHY_971_DATA */
+ 0x00000000 /* DENALI_PHY_972_DATA */
+ 0x00000000 /* DENALI_PHY_973_DATA */
+ 0x00000000 /* DENALI_PHY_974_DATA */
+ 0x00000000 /* DENALI_PHY_975_DATA */
+ 0x00000000 /* DENALI_PHY_976_DATA */
+ 0x00000000 /* DENALI_PHY_977_DATA */
+ 0x00000000 /* DENALI_PHY_978_DATA */
+ 0x00000000 /* DENALI_PHY_979_DATA */
+ 0x00000000 /* DENALI_PHY_980_DATA */
+ 0x00000000 /* DENALI_PHY_981_DATA */
+ 0x00000000 /* DENALI_PHY_982_DATA */
+ 0x00000000 /* DENALI_PHY_983_DATA */
+ 0x00000000 /* DENALI_PHY_984_DATA */
+ 0x00000000 /* DENALI_PHY_985_DATA */
+ 0x00000000 /* DENALI_PHY_986_DATA */
+ 0x00000000 /* DENALI_PHY_987_DATA */
+ 0x00000000 /* DENALI_PHY_988_DATA */
+ 0x00000000 /* DENALI_PHY_989_DATA */
+ 0x00000000 /* DENALI_PHY_990_DATA */
+ 0x00000000 /* DENALI_PHY_991_DATA */
+ 0x00000000 /* DENALI_PHY_992_DATA */
+ 0x00000000 /* DENALI_PHY_993_DATA */
+ 0x00000000 /* DENALI_PHY_994_DATA */
+ 0x00000000 /* DENALI_PHY_995_DATA */
+ 0x00000000 /* DENALI_PHY_996_DATA */
+ 0x00000000 /* DENALI_PHY_997_DATA */
+ 0x00000000 /* DENALI_PHY_998_DATA */
+ 0x00000000 /* DENALI_PHY_999_DATA */
+ 0x00000000 /* DENALI_PHY_1000_DATA */
+ 0x00000000 /* DENALI_PHY_1001_DATA */
+ 0x00000000 /* DENALI_PHY_1002_DATA */
+ 0x00000000 /* DENALI_PHY_1003_DATA */
+ 0x00000000 /* DENALI_PHY_1004_DATA */
+ 0x00000000 /* DENALI_PHY_1005_DATA */
+ 0x00000000 /* DENALI_PHY_1006_DATA */
+ 0x00000000 /* DENALI_PHY_1007_DATA */
+ 0x00000000 /* DENALI_PHY_1008_DATA */
+ 0x00000000 /* DENALI_PHY_1009_DATA */
+ 0x00000000 /* DENALI_PHY_1010_DATA */
+ 0x00000000 /* DENALI_PHY_1011_DATA */
+ 0x00000000 /* DENALI_PHY_1012_DATA */
+ 0x00000000 /* DENALI_PHY_1013_DATA */
+ 0x00000000 /* DENALI_PHY_1014_DATA */
+ 0x00000000 /* DENALI_PHY_1015_DATA */
+ 0x00000000 /* DENALI_PHY_1016_DATA */
+ 0x00000000 /* DENALI_PHY_1017_DATA */
+ 0x00000000 /* DENALI_PHY_1018_DATA */
+ 0x00000000 /* DENALI_PHY_1019_DATA */
+ 0x00000000 /* DENALI_PHY_1020_DATA */
+ 0x00000000 /* DENALI_PHY_1021_DATA */
+ 0x00000000 /* DENALI_PHY_1022_DATA */
+ 0x00000000 /* DENALI_PHY_1023_DATA */
+ 0x36025174 /* DENALI_PHY_1024_DATA */
+ 0x0004c008 /* DENALI_PHY_1025_DATA */
+ 0x000000da /* DENALI_PHY_1026_DATA */
+ 0x00000000 /* DENALI_PHY_1027_DATA */
+ 0x00000000 /* DENALI_PHY_1028_DATA */
+ 0x00010000 /* DENALI_PHY_1029_DATA */
+ 0x01DDDD90 /* DENALI_PHY_1030_DATA */
+ 0x01DDDD90 /* DENALI_PHY_1031_DATA */
+ 0x01030000 /* DENALI_PHY_1032_DATA */
+ 0x01000000 /* DENALI_PHY_1033_DATA */
+ 0x00c00000 /* DENALI_PHY_1034_DATA */
+ 0x00000007 /* DENALI_PHY_1035_DATA */
+ 0x00000000 /* DENALI_PHY_1036_DATA */
+ 0x00000000 /* DENALI_PHY_1037_DATA */
+ 0x04000408 /* DENALI_PHY_1038_DATA */
+ 0x00000408 /* DENALI_PHY_1039_DATA */
+ 0x00e4e400 /* DENALI_PHY_1040_DATA */
+ 0x00000000 /* DENALI_PHY_1041_DATA */
+ 0x00000000 /* DENALI_PHY_1042_DATA */
+ 0x00000000 /* DENALI_PHY_1043_DATA */
+ 0x00000000 /* DENALI_PHY_1044_DATA */
+ 0x00000000 /* DENALI_PHY_1045_DATA */
+ 0x00000000 /* DENALI_PHY_1046_DATA */
+ 0x00000000 /* DENALI_PHY_1047_DATA */
+ 0x00000000 /* DENALI_PHY_1048_DATA */
+ 0x00000000 /* DENALI_PHY_1049_DATA */
+ 0x00000000 /* DENALI_PHY_1050_DATA */
+ 0x00000000 /* DENALI_PHY_1051_DATA */
+ 0x00000000 /* DENALI_PHY_1052_DATA */
+ 0x00000000 /* DENALI_PHY_1053_DATA */
+ 0x00000000 /* DENALI_PHY_1054_DATA */
+ 0x00000000 /* DENALI_PHY_1055_DATA */
+ 0x00000000 /* DENALI_PHY_1056_DATA */
+ 0x00200000 /* DENALI_PHY_1057_DATA */
+ 0x00000000 /* DENALI_PHY_1058_DATA */
+ 0x00000000 /* DENALI_PHY_1059_DATA */
+ 0x00000000 /* DENALI_PHY_1060_DATA */
+ 0x00000000 /* DENALI_PHY_1061_DATA */
+ 0x00000000 /* DENALI_PHY_1062_DATA */
+ 0x00000000 /* DENALI_PHY_1063_DATA */
+ 0x02800280 /* DENALI_PHY_1064_DATA */
+ 0x02800280 /* DENALI_PHY_1065_DATA */
+ 0x02800280 /* DENALI_PHY_1066_DATA */
+ 0x02800280 /* DENALI_PHY_1067_DATA */
+ 0x00000280 /* DENALI_PHY_1068_DATA */
+ 0x00000000 /* DENALI_PHY_1069_DATA */
+ 0x00000000 /* DENALI_PHY_1070_DATA */
+ 0x00000000 /* DENALI_PHY_1071_DATA */
+ 0x00000000 /* DENALI_PHY_1072_DATA */
+ 0x00000000 /* DENALI_PHY_1073_DATA */
+ 0x00800080 /* DENALI_PHY_1074_DATA */
+ 0x00800080 /* DENALI_PHY_1075_DATA */
+ 0x00800080 /* DENALI_PHY_1076_DATA */
+ 0x00800080 /* DENALI_PHY_1077_DATA */
+ 0x00800080 /* DENALI_PHY_1078_DATA */
+ 0x00800080 /* DENALI_PHY_1079_DATA */
+ 0x00800080 /* DENALI_PHY_1080_DATA */
+ 0x00800080 /* DENALI_PHY_1081_DATA */
+ 0x00800080 /* DENALI_PHY_1082_DATA */
+ 0x000100da /* DENALI_PHY_1083_DATA */
+ 0x00000200 /* DENALI_PHY_1084_DATA */
+ 0x00000000 /* DENALI_PHY_1085_DATA */
+ 0x00000000 /* DENALI_PHY_1086_DATA */
+ 0x00000002 /* DENALI_PHY_1087_DATA */
+ 0x51313152 /* DENALI_PHY_1088_DATA */
+ 0x80013130 /* DENALI_PHY_1089_DATA */
+ 0x02000080 /* DENALI_PHY_1090_DATA */
+ 0x00100001 /* DENALI_PHY_1091_DATA */
+ 0x0c064208 /* DENALI_PHY_1092_DATA */
+ 0x000f0c0f /* DENALI_PHY_1093_DATA */
+ 0x01000140 /* DENALI_PHY_1094_DATA */
+ 0x0000000c /* DENALI_PHY_1095_DATA */
+ 0x00000000 /* DENALI_PHY_1096_DATA */
+ 0x00000000 /* DENALI_PHY_1097_DATA */
+ 0x00000000 /* DENALI_PHY_1098_DATA */
+ 0x00000000 /* DENALI_PHY_1099_DATA */
+ 0x00000000 /* DENALI_PHY_1100_DATA */
+ 0x00000000 /* DENALI_PHY_1101_DATA */
+ 0x00000000 /* DENALI_PHY_1102_DATA */
+ 0x00000000 /* DENALI_PHY_1103_DATA */
+ 0x00000000 /* DENALI_PHY_1104_DATA */
+ 0x00000000 /* DENALI_PHY_1105_DATA */
+ 0x00000000 /* DENALI_PHY_1106_DATA */
+ 0x00000000 /* DENALI_PHY_1107_DATA */
+ 0x00000000 /* DENALI_PHY_1108_DATA */
+ 0x00000000 /* DENALI_PHY_1109_DATA */
+ 0x00000000 /* DENALI_PHY_1110_DATA */
+ 0x00000000 /* DENALI_PHY_1111_DATA */
+ 0x00000000 /* DENALI_PHY_1112_DATA */
+ 0x00000000 /* DENALI_PHY_1113_DATA */
+ 0x00000000 /* DENALI_PHY_1114_DATA */
+ 0x00000000 /* DENALI_PHY_1115_DATA */
+ 0x00000000 /* DENALI_PHY_1116_DATA */
+ 0x00000000 /* DENALI_PHY_1117_DATA */
+ 0x00000000 /* DENALI_PHY_1118_DATA */
+ 0x00000000 /* DENALI_PHY_1119_DATA */
+ 0x00000000 /* DENALI_PHY_1120_DATA */
+ 0x00000000 /* DENALI_PHY_1121_DATA */
+ 0x00000000 /* DENALI_PHY_1122_DATA */
+ 0x00000000 /* DENALI_PHY_1123_DATA */
+ 0x00000000 /* DENALI_PHY_1124_DATA */
+ 0x00000000 /* DENALI_PHY_1125_DATA */
+ 0x00000000 /* DENALI_PHY_1126_DATA */
+ 0x00000000 /* DENALI_PHY_1127_DATA */
+ 0x00000000 /* DENALI_PHY_1128_DATA */
+ 0x00000000 /* DENALI_PHY_1129_DATA */
+ 0x00000000 /* DENALI_PHY_1130_DATA */
+ 0x00000000 /* DENALI_PHY_1131_DATA */
+ 0x00000000 /* DENALI_PHY_1132_DATA */
+ 0x00000000 /* DENALI_PHY_1133_DATA */
+ 0x00000000 /* DENALI_PHY_1134_DATA */
+ 0x00000000 /* DENALI_PHY_1135_DATA */
+ 0x00000000 /* DENALI_PHY_1136_DATA */
+ 0x00000000 /* DENALI_PHY_1137_DATA */
+ 0x00000000 /* DENALI_PHY_1138_DATA */
+ 0x00000000 /* DENALI_PHY_1139_DATA */
+ 0x00000000 /* DENALI_PHY_1140_DATA */
+ 0x00000000 /* DENALI_PHY_1141_DATA */
+ 0x00000000 /* DENALI_PHY_1142_DATA */
+ 0x00000000 /* DENALI_PHY_1143_DATA */
+ 0x00000000 /* DENALI_PHY_1144_DATA */
+ 0x00000000 /* DENALI_PHY_1145_DATA */
+ 0x00000000 /* DENALI_PHY_1146_DATA */
+ 0x00000000 /* DENALI_PHY_1147_DATA */
+ 0x00000000 /* DENALI_PHY_1148_DATA */
+ 0x00000000 /* DENALI_PHY_1149_DATA */
+ 0x00000000 /* DENALI_PHY_1150_DATA */
+ 0x00000000 /* DENALI_PHY_1151_DATA */
+ 0x00000000 /* DENALI_PHY_1152_DATA */
+ 0x00000000 /* DENALI_PHY_1153_DATA */
+ 0x00050000 /* DENALI_PHY_1154_DATA */
+ 0x00000000 /* DENALI_PHY_1155_DATA */
+ 0x00000000 /* DENALI_PHY_1156_DATA */
+ 0x00000000 /* DENALI_PHY_1157_DATA */
+ 0x00000100 /* DENALI_PHY_1158_DATA */
+ 0x00000000 /* DENALI_PHY_1159_DATA */
+ 0x00000000 /* DENALI_PHY_1160_DATA */
+ 0x00506401 /* DENALI_PHY_1161_DATA */
+ 0x01221102 /* DENALI_PHY_1162_DATA */
+ 0x00000122 /* DENALI_PHY_1163_DATA */
+ 0x00000000 /* DENALI_PHY_1164_DATA */
+ 0x000B1F00 /* DENALI_PHY_1165_DATA */
+ 0x0B1F0B1F /* DENALI_PHY_1166_DATA */
+ 0x0B1F0B1B /* DENALI_PHY_1167_DATA */
+ 0x0B1F0B1F /* DENALI_PHY_1168_DATA */
+ 0x0B1F0B1F /* DENALI_PHY_1169_DATA */
+ 0x00000B00 /* DENALI_PHY_1170_DATA */
+ 0x42080010 /* DENALI_PHY_1171_DATA */
+ 0x01000100 /* DENALI_PHY_1172_DATA */
+ 0x01000100 /* DENALI_PHY_1173_DATA */
+ 0x01000100 /* DENALI_PHY_1174_DATA */
+ 0x01000100 /* DENALI_PHY_1175_DATA */
+ 0x00000000 /* DENALI_PHY_1176_DATA */
+ 0x00000000 /* DENALI_PHY_1177_DATA */
+ 0x00000000 /* DENALI_PHY_1178_DATA */
+ 0x00000000 /* DENALI_PHY_1179_DATA */
+ 0x00000000 /* DENALI_PHY_1180_DATA */
+ 0x00000803 /* DENALI_PHY_1181_DATA */
+ 0x223FFF00 /* DENALI_PHY_1182_DATA */
+ 0x000008FF /* DENALI_PHY_1183_DATA */
+ 0x0000057F /* DENALI_PHY_1184_DATA */
+ 0x0000057F /* DENALI_PHY_1185_DATA */
+ 0x00037FFF /* DENALI_PHY_1186_DATA */
+ 0x00037FFF /* DENALI_PHY_1187_DATA */
+ 0x00004410 /* DENALI_PHY_1188_DATA */
+ 0x00004410 /* DENALI_PHY_1189_DATA */
+ 0x00004410 /* DENALI_PHY_1190_DATA */
+ 0x00004410 /* DENALI_PHY_1191_DATA */
+ 0x00004410 /* DENALI_PHY_1192_DATA */
+ 0x00037FFF /* DENALI_PHY_1193_DATA */
+ 0x00037FFF /* DENALI_PHY_1194_DATA */
+ 0x00000000 /* DENALI_PHY_1195_DATA */
+ 0x00000000 /* DENALI_PHY_1196_DATA */
+ 0x00000000 /* DENALI_PHY_1197_DATA */
+ 0x04000000 /* DENALI_PHY_1198_DATA */
+ 0x00000000 /* DENALI_PHY_1199_DATA */
+ 0x00000000 /* DENALI_PHY_1200_DATA */
+ 0x00000108 /* DENALI_PHY_1201_DATA */
+ 0x00000000 /* DENALI_PHY_1202_DATA */
+ 0x00000000 /* DENALI_PHY_1203_DATA */
+ 0x00000000 /* DENALI_PHY_1204_DATA */
+ 0x00000001 /* DENALI_PHY_1205_DATA */
+ 0x00000000 /* DENALI_PHY_1206_DATA */
+ 0x00000000 /* DENALI_PHY_1207_DATA */
+ 0x00000000 /* DENALI_PHY_1208_DATA */
+ 0x00000000 /* DENALI_PHY_1209_DATA */
+ 0x00000000 /* DENALI_PHY_1210_DATA */
+ 0x00000000 /* DENALI_PHY_1211_DATA */
+ 0x00020100 /* DENALI_PHY_1212_DATA */
+ 0x00000000 /* DENALI_PHY_1213_DATA */
+ 0x00000000 /* DENALI_PHY_1214_DATA */
+ >;
+};
--
2.17.1
^ permalink raw reply related [flat|nested] 118+ messages in thread
* [PATCH v7 08/22] riscv: sifive: dts: fu540: add U-Boot dmc node
2020-05-02 10:06 [PATCH v7 00/22] RISC-V SiFive FU540 support SPL Pragnesh Patel
` (6 preceding siblings ...)
2020-05-02 10:06 ` [PATCH v7 07/22] sifive: dts: fu540: Add DDR controller and phy register settings Pragnesh Patel
@ 2020-05-02 10:06 ` Pragnesh Patel
2020-05-02 12:29 ` Bin Meng
2020-05-02 10:06 ` [PATCH v7 09/22] clk: sifive: fu540-prci: Add clock enable and disable ops Pragnesh Patel
` (14 subsequent siblings)
22 siblings, 1 reply; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-02 10:06 UTC (permalink / raw)
To: u-boot
Add dmc node to enable sdram driver. dmc is used to
initialize the memory controller.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
---
arch/riscv/dts/fu540-c000-u-boot.dtsi | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/arch/riscv/dts/fu540-c000-u-boot.dtsi b/arch/riscv/dts/fu540-c000-u-boot.dtsi
index 387b13bdfb..e93b8a9bcf 100644
--- a/arch/riscv/dts/fu540-c000-u-boot.dtsi
+++ b/arch/riscv/dts/fu540-c000-u-boot.dtsi
@@ -52,6 +52,15 @@
reg = <0x0 0x2000000 0x0 0xc0000>;
u-boot,dm-spl;
};
+ dmc: dmc at 100b0000 {
+ compatible = "sifive,fu540-c000-ddr";
+ reg = <0x0 0x100b0000 0x0 0x0800
+ 0x0 0x100b2000 0x0 0x2000
+ 0x0 0x100b8000 0x0 0x0fff>;
+ clocks = <&prci PRCI_CLK_DDRPLL>;
+ clock-frequency = <933333324>;
+ u-boot,dm-spl;
+ };
};
};
--
2.17.1
^ permalink raw reply related [flat|nested] 118+ messages in thread
* [PATCH v7 09/22] clk: sifive: fu540-prci: Add clock enable and disable ops
2020-05-02 10:06 [PATCH v7 00/22] RISC-V SiFive FU540 support SPL Pragnesh Patel
` (7 preceding siblings ...)
2020-05-02 10:06 ` [PATCH v7 08/22] riscv: sifive: dts: fu540: add U-Boot dmc node Pragnesh Patel
@ 2020-05-02 10:06 ` Pragnesh Patel
2020-05-02 12:29 ` Bin Meng
2020-05-02 10:06 ` [PATCH v7 10/22] clk: sifive: fu540-prci: ddr and ethernet clock initialization in SPL Pragnesh Patel
` (13 subsequent siblings)
22 siblings, 1 reply; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-02 10:06 UTC (permalink / raw)
To: u-boot
Added clock enable and disable functions in prci ops
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
---
drivers/clk/sifive/fu540-prci.c | 108 ++++++++++++++++++++++++++++----
1 file changed, 96 insertions(+), 12 deletions(-)
diff --git a/drivers/clk/sifive/fu540-prci.c b/drivers/clk/sifive/fu540-prci.c
index 8847178001..bf06c3a3bb 100644
--- a/drivers/clk/sifive/fu540-prci.c
+++ b/drivers/clk/sifive/fu540-prci.c
@@ -68,6 +68,11 @@
#define PRCI_COREPLLCFG0_LOCK_SHIFT 31
#define PRCI_COREPLLCFG0_LOCK_MASK (0x1 << PRCI_COREPLLCFG0_LOCK_SHIFT)
+/* COREPLLCFG1 */
+#define PRCI_COREPLLCFG1_OFFSET 0x8
+#define PRCI_COREPLLCFG1_CKE_SHIFT 31
+#define PRCI_COREPLLCFG1_CKE_MASK (0x1 << PRCI_COREPLLCFG1_CKE_SHIFT)
+
/* DDRPLLCFG0 */
#define PRCI_DDRPLLCFG0_OFFSET 0xc
#define PRCI_DDRPLLCFG0_DIVR_SHIFT 0
@@ -87,7 +92,7 @@
/* DDRPLLCFG1 */
#define PRCI_DDRPLLCFG1_OFFSET 0x10
-#define PRCI_DDRPLLCFG1_CKE_SHIFT 24
+#define PRCI_DDRPLLCFG1_CKE_SHIFT 31
#define PRCI_DDRPLLCFG1_CKE_MASK (0x1 << PRCI_DDRPLLCFG1_CKE_SHIFT)
/* GEMGXLPLLCFG0 */
@@ -114,7 +119,7 @@
/* GEMGXLPLLCFG1 */
#define PRCI_GEMGXLPLLCFG1_OFFSET 0x20
-#define PRCI_GEMGXLPLLCFG1_CKE_SHIFT 24
+#define PRCI_GEMGXLPLLCFG1_CKE_SHIFT 31
#define PRCI_GEMGXLPLLCFG1_CKE_MASK (0x1 << PRCI_GEMGXLPLLCFG1_CKE_SHIFT)
/* CORECLKSEL */
@@ -142,7 +147,7 @@
(0x1 << PRCI_DEVICESRESETREG_GEMGXL_RST_N_SHIFT)
/* CLKMUXSTATUSREG */
-#define PRCI_CLKMUXSTATUSREG_OFFSET 0x2c
+#define PRCI_CLKMUXSTATUSREG_OFFSET 0x2c
#define PRCI_CLKMUXSTATUSREG_TLCLKSEL_STATUS_SHIFT 1
#define PRCI_CLKMUXSTATUSREG_TLCLKSEL_STATUS_MASK \
(0x1 << PRCI_CLKMUXSTATUSREG_TLCLKSEL_STATUS_SHIFT)
@@ -170,6 +175,7 @@ struct __prci_data {
* @enable_bypass: fn ptr to code to bypass the WRPLL (if applicable; else NULL)
* @disable_bypass: fn ptr to code to not bypass the WRPLL (or NULL)
* @cfg0_offs: WRPLL CFG0 register offset (in bytes) from the PRCI base address
+ * @cfg1_offs: WRPLL CFG1 register offset (in bytes) from the PRCI base address
*
* @enable_bypass and @disable_bypass are used for WRPLL instances
* that contain a separate external glitchless clock mux downstream
@@ -180,6 +186,7 @@ struct __prci_wrpll_data {
void (*enable_bypass)(struct __prci_data *pd);
void (*disable_bypass)(struct __prci_data *pd);
u8 cfg0_offs;
+ u8 cfg1_offs;
};
struct __prci_clock;
@@ -194,6 +201,7 @@ struct __prci_clock_ops {
unsigned long *parent_rate);
unsigned long (*recalc_rate)(struct __prci_clock *pc,
unsigned long parent_rate);
+ int (*enable_clk)(struct __prci_clock *pc, bool enable);
};
/**
@@ -316,7 +324,7 @@ static u32 __prci_wrpll_pack(const struct wrpll_cfg *c)
}
/**
- * __prci_wrpll_read_cfg() - read the WRPLL configuration from the PRCI
+ * __prci_wrpll_read_cfg0() - read the WRPLL configuration from the PRCI
* @pd: PRCI context
* @pwd: PRCI WRPLL metadata
*
@@ -327,14 +335,14 @@ static u32 __prci_wrpll_pack(const struct wrpll_cfg *c)
* Context: Any context. Caller must prevent the records pointed to by
* @pd and @pwd from changing during execution.
*/
-static void __prci_wrpll_read_cfg(struct __prci_data *pd,
- struct __prci_wrpll_data *pwd)
+static void __prci_wrpll_read_cfg0(struct __prci_data *pd,
+ struct __prci_wrpll_data *pwd)
{
__prci_wrpll_unpack(&pwd->c, __prci_readl(pd, pwd->cfg0_offs));
}
/**
- * __prci_wrpll_write_cfg() - write WRPLL configuration into the PRCI
+ * __prci_wrpll_write_cfg0() - write WRPLL configuration into the PRCI
* @pd: PRCI context
* @pwd: PRCI WRPLL metadata
* @c: WRPLL configuration record to write
@@ -347,15 +355,29 @@ static void __prci_wrpll_read_cfg(struct __prci_data *pd,
* Context: Any context. Caller must prevent the records pointed to by
* @pd and @pwd from changing during execution.
*/
-static void __prci_wrpll_write_cfg(struct __prci_data *pd,
- struct __prci_wrpll_data *pwd,
- struct wrpll_cfg *c)
+static void __prci_wrpll_write_cfg0(struct __prci_data *pd,
+ struct __prci_wrpll_data *pwd,
+ struct wrpll_cfg *c)
{
__prci_writel(__prci_wrpll_pack(c), pwd->cfg0_offs, pd);
memcpy(&pwd->c, c, sizeof(*c));
}
+/**
+ * __prci_wrpll_write_cfg1() - write Clock enable/disable configuration
+ * into the PRCI
+ * @pd: PRCI context
+ * @pwd: PRCI WRPLL metadata
+ * @enable: Clock enable or disable value
+ */
+static void __prci_wrpll_write_cfg1(struct __prci_data *pd,
+ struct __prci_wrpll_data *pwd,
+ u32 enable)
+{
+ __prci_writel(enable, pwd->cfg1_offs, pd);
+}
+
/* Core clock mux control */
/**
@@ -437,7 +459,7 @@ static int sifive_fu540_prci_wrpll_set_rate(struct __prci_clock *pc,
if (pwd->enable_bypass)
pwd->enable_bypass(pd);
- __prci_wrpll_write_cfg(pd, pwd, &pwd->c);
+ __prci_wrpll_write_cfg0(pd, pwd, &pwd->c);
udelay(wrpll_calc_max_lock_us(&pwd->c));
@@ -447,14 +469,35 @@ static int sifive_fu540_prci_wrpll_set_rate(struct __prci_clock *pc,
return 0;
}
+static int sifive_fu540_prci_clock_enable(struct __prci_clock *pc, bool enable)
+{
+ struct __prci_wrpll_data *pwd = pc->pwd;
+ struct __prci_data *pd = pc->pd;
+
+ if (enable) {
+ __prci_wrpll_write_cfg1(pd, pwd, PRCI_COREPLLCFG1_CKE_MASK);
+ } else {
+ u32 r;
+
+ r = __prci_readl(pd, pwd->cfg1_offs);
+ r &= ~PRCI_COREPLLCFG1_CKE_MASK;
+
+ __prci_wrpll_write_cfg1(pd, pwd, r);
+ }
+
+ return 0;
+}
+
static const struct __prci_clock_ops sifive_fu540_prci_wrpll_clk_ops = {
.set_rate = sifive_fu540_prci_wrpll_set_rate,
.round_rate = sifive_fu540_prci_wrpll_round_rate,
.recalc_rate = sifive_fu540_prci_wrpll_recalc_rate,
+ .enable_clk = sifive_fu540_prci_clock_enable,
};
static const struct __prci_clock_ops sifive_fu540_prci_wrpll_ro_clk_ops = {
.recalc_rate = sifive_fu540_prci_wrpll_recalc_rate,
+ .enable_clk = sifive_fu540_prci_clock_enable,
};
/* TLCLKSEL clock integration */
@@ -484,16 +527,19 @@ static const struct __prci_clock_ops sifive_fu540_prci_tlclksel_clk_ops = {
static struct __prci_wrpll_data __prci_corepll_data = {
.cfg0_offs = PRCI_COREPLLCFG0_OFFSET,
+ .cfg1_offs = PRCI_COREPLLCFG1_OFFSET,
.enable_bypass = __prci_coreclksel_use_hfclk,
.disable_bypass = __prci_coreclksel_use_corepll,
};
static struct __prci_wrpll_data __prci_ddrpll_data = {
.cfg0_offs = PRCI_DDRPLLCFG0_OFFSET,
+ .cfg1_offs = PRCI_DDRPLLCFG1_OFFSET,
};
static struct __prci_wrpll_data __prci_gemgxlpll_data = {
.cfg0_offs = PRCI_GEMGXLPLLCFG0_OFFSET,
+ .cfg1_offs = PRCI_GEMGXLPLLCFG1_OFFSET,
};
/*
@@ -580,6 +626,42 @@ static ulong sifive_fu540_prci_set_rate(struct clk *clk, ulong rate)
return rate;
}
+static int sifive_fu540_prci_enable(struct clk *clk)
+{
+ struct __prci_clock *pc;
+ int ret = 0;
+
+ if (ARRAY_SIZE(__prci_init_clocks) <= clk->id)
+ return -ENXIO;
+
+ pc = &__prci_init_clocks[clk->id];
+ if (!pc->pd)
+ return -ENXIO;
+
+ if (pc->ops->enable_clk)
+ ret = pc->ops->enable_clk(pc, 1);
+
+ return ret;
+}
+
+static int sifive_fu540_prci_disable(struct clk *clk)
+{
+ struct __prci_clock *pc;
+ int ret = 0;
+
+ if (ARRAY_SIZE(__prci_init_clocks) <= clk->id)
+ return -ENXIO;
+
+ pc = &__prci_init_clocks[clk->id];
+ if (!pc->pd)
+ return -ENXIO;
+
+ if (pc->ops->enable_clk)
+ ret = pc->ops->enable_clk(pc, 0);
+
+ return ret;
+}
+
static int sifive_fu540_prci_probe(struct udevice *dev)
{
int i, err;
@@ -602,7 +684,7 @@ static int sifive_fu540_prci_probe(struct udevice *dev)
pc = &__prci_init_clocks[i];
pc->pd = pd;
if (pc->pwd)
- __prci_wrpll_read_cfg(pd, pc->pwd);
+ __prci_wrpll_read_cfg0(pd, pc->pwd);
}
return 0;
@@ -611,6 +693,8 @@ static int sifive_fu540_prci_probe(struct udevice *dev)
static struct clk_ops sifive_fu540_prci_ops = {
.set_rate = sifive_fu540_prci_set_rate,
.get_rate = sifive_fu540_prci_get_rate,
+ .enable = sifive_fu540_prci_enable,
+ .disable = sifive_fu540_prci_disable,
};
static const struct udevice_id sifive_fu540_prci_ids[] = {
--
2.17.1
^ permalink raw reply related [flat|nested] 118+ messages in thread
* [PATCH v7 10/22] clk: sifive: fu540-prci: ddr and ethernet clock initialization in SPL
2020-05-02 10:06 [PATCH v7 00/22] RISC-V SiFive FU540 support SPL Pragnesh Patel
` (8 preceding siblings ...)
2020-05-02 10:06 ` [PATCH v7 09/22] clk: sifive: fu540-prci: Add clock enable and disable ops Pragnesh Patel
@ 2020-05-02 10:06 ` Pragnesh Patel
2020-05-02 12:28 ` Bin Meng
2020-05-02 16:14 ` Jagan Teki
2020-05-02 10:06 ` [PATCH v7 11/22] riscv: dts: sifive: Sync hifive-unleashed-a00 dts from linux Pragnesh Patel
` (12 subsequent siblings)
22 siblings, 2 replies; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-02 10:06 UTC (permalink / raw)
To: u-boot
Add ddr clock release reset and ehternet clock initialization for
SPL
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
---
drivers/clk/sifive/fu540-prci.c | 87 ++++++++++++++++++++++++++++++---
1 file changed, 81 insertions(+), 6 deletions(-)
diff --git a/drivers/clk/sifive/fu540-prci.c b/drivers/clk/sifive/fu540-prci.c
index bf06c3a3bb..1c89bdf242 100644
--- a/drivers/clk/sifive/fu540-prci.c
+++ b/drivers/clk/sifive/fu540-prci.c
@@ -41,6 +41,8 @@
#include <linux/clk/analogbits-wrpll-cln28hpc.h>
#include <dt-bindings/clock/sifive-fu540-prci.h>
+#define MHz 1000000
+
/*
* EXPECTED_CLK_PARENT_COUNT: how many parent clocks this driver expects:
* hfclk and rtcclk
@@ -152,6 +154,12 @@
#define PRCI_CLKMUXSTATUSREG_TLCLKSEL_STATUS_MASK \
(0x1 << PRCI_CLKMUXSTATUSREG_TLCLKSEL_STATUS_SHIFT)
+/* PROCMONCFG */
+#define PRCI_PROCMONCFG_OFFSET 0xF0
+#define PRCI_PROCMONCFG_CORE_CLOCK_SHIFT 24
+#define PRCI_PROCMONCFG_CORE_CLOCK_MASK \
+ (0x1 << PRCI_PROCMONCFG_CORE_CLOCK_SHIFT)
+
/*
* Private structures
*/
@@ -176,6 +184,7 @@ struct __prci_data {
* @disable_bypass: fn ptr to code to not bypass the WRPLL (or NULL)
* @cfg0_offs: WRPLL CFG0 register offset (in bytes) from the PRCI base address
* @cfg1_offs: WRPLL CFG1 register offset (in bytes) from the PRCI base address
+ * @release_reset: fn ptr to code to release clock reset
*
* @enable_bypass and @disable_bypass are used for WRPLL instances
* that contain a separate external glitchless clock mux downstream
@@ -187,6 +196,9 @@ struct __prci_wrpll_data {
void (*disable_bypass)(struct __prci_data *pd);
u8 cfg0_offs;
u8 cfg1_offs;
+#ifdef CONFIG_SPL_BUILD
+ void (*release_reset)(struct __prci_data *pd);
+#endif
};
struct __prci_clock;
@@ -476,6 +488,11 @@ static int sifive_fu540_prci_clock_enable(struct __prci_clock *pc, bool enable)
if (enable) {
__prci_wrpll_write_cfg1(pd, pwd, PRCI_COREPLLCFG1_CKE_MASK);
+
+#ifdef CONFIG_SPL_BUILD
+ if (pwd->release_reset)
+ pwd->release_reset(pd);
+#endif
} else {
u32 r;
@@ -495,11 +512,6 @@ static const struct __prci_clock_ops sifive_fu540_prci_wrpll_clk_ops = {
.enable_clk = sifive_fu540_prci_clock_enable,
};
-static const struct __prci_clock_ops sifive_fu540_prci_wrpll_ro_clk_ops = {
- .recalc_rate = sifive_fu540_prci_wrpll_recalc_rate,
- .enable_clk = sifive_fu540_prci_clock_enable,
-};
-
/* TLCLKSEL clock integration */
static unsigned long sifive_fu540_prci_tlclksel_recalc_rate(
@@ -521,6 +533,39 @@ static const struct __prci_clock_ops sifive_fu540_prci_tlclksel_clk_ops = {
.recalc_rate = sifive_fu540_prci_tlclksel_recalc_rate,
};
+#ifdef CONFIG_SPL_BUILD
+/**
+ * __prci_ddr_release_reset() - Release DDR reset
+ * @pd: struct __prci_data * for the PRCI containing the DDRCLK mux reg
+ *
+ */
+static void __prci_ddr_release_reset(struct __prci_data *pd)
+{
+ u32 v;
+
+ v = __prci_readl(pd, PRCI_DEVICESRESETREG_OFFSET);
+ v |= PRCI_DEVICESRESETREG_DDR_CTRL_RST_N_MASK;
+ __prci_writel(v, PRCI_DEVICESRESETREG_OFFSET, pd);
+
+ // HACK to get the '1 full controller clock cycle'.
+ asm volatile ("fence");
+ v = __prci_readl(pd, PRCI_DEVICESRESETREG_OFFSET);
+ v |= (PRCI_DEVICESRESETREG_DDR_AXI_RST_N_MASK |
+ PRCI_DEVICESRESETREG_DDR_AHB_RST_N_MASK |
+ PRCI_DEVICESRESETREG_DDR_PHY_RST_N_MASK);
+ __prci_writel(v, PRCI_DEVICESRESETREG_OFFSET, pd);
+ // HACK to get the '1 full controller clock cycle'.
+ asm volatile ("fence");
+
+ /* These take like 16 cycles to actually propagate. We can't go sending
+ * stuff before they come out of reset. So wait. (TODO: Add a register
+ * to read the current reset states, or DDR Control device?)
+ */
+ for (int i = 0; i < 256; i++)
+ asm volatile ("nop");
+}
+#endif
+
/*
* PRCI integration data for each WRPLL instance
*/
@@ -535,6 +580,9 @@ static struct __prci_wrpll_data __prci_corepll_data = {
static struct __prci_wrpll_data __prci_ddrpll_data = {
.cfg0_offs = PRCI_DDRPLLCFG0_OFFSET,
.cfg1_offs = PRCI_DDRPLLCFG1_OFFSET,
+#ifdef CONFIG_SPL_BUILD
+ .release_reset = __prci_ddr_release_reset,
+#endif
};
static struct __prci_wrpll_data __prci_gemgxlpll_data = {
@@ -556,7 +604,7 @@ static struct __prci_clock __prci_init_clocks[] = {
[PRCI_CLK_DDRPLL] = {
.name = "ddrpll",
.parent_name = "hfclk",
- .ops = &sifive_fu540_prci_wrpll_ro_clk_ops,
+ .ops = &sifive_fu540_prci_wrpll_clk_ops,
.pwd = &__prci_ddrpll_data,
},
[PRCI_CLK_GEMGXLPLL] = {
@@ -662,6 +710,29 @@ static int sifive_fu540_prci_disable(struct clk *clk)
return ret;
}
+#ifdef CONFIG_SPL_BUILD
+static void ethernet_init(struct udevice *dev)
+{
+ u32 v;
+ struct clk clock;
+ struct __prci_data *pd = dev_get_priv(dev);
+
+ /* GEMGXL init */
+ clock.id = PRCI_CLK_GEMGXLPLL;
+ sifive_fu540_prci_set_rate(&clock, 125UL * MHz);
+ sifive_fu540_prci_clock_enable(&__prci_init_clocks[clock.id], 1);
+
+ /* Release GEMGXL reset */
+ v = __prci_readl(pd, PRCI_DEVICESRESETREG_OFFSET);
+ v |= PRCI_DEVICESRESETREG_GEMGXL_RST_N_MASK;
+ __prci_writel(v, PRCI_DEVICESRESETREG_OFFSET, pd);
+
+ /* Procmon => core clock */
+ __prci_writel(PRCI_PROCMONCFG_CORE_CLOCK_MASK, PRCI_PROCMONCFG_OFFSET,
+ pd);
+}
+#endif
+
static int sifive_fu540_prci_probe(struct udevice *dev)
{
int i, err;
@@ -687,6 +758,10 @@ static int sifive_fu540_prci_probe(struct udevice *dev)
__prci_wrpll_read_cfg0(pd, pc->pwd);
}
+#ifdef CONFIG_SPL_BUILD
+ ethernet_init(dev);
+#endif
+
return 0;
}
--
2.17.1
^ permalink raw reply related [flat|nested] 118+ messages in thread
* [PATCH v7 11/22] riscv: dts: sifive: Sync hifive-unleashed-a00 dts from linux
2020-05-02 10:06 [PATCH v7 00/22] RISC-V SiFive FU540 support SPL Pragnesh Patel
` (9 preceding siblings ...)
2020-05-02 10:06 ` [PATCH v7 10/22] clk: sifive: fu540-prci: ddr and ethernet clock initialization in SPL Pragnesh Patel
@ 2020-05-02 10:06 ` Pragnesh Patel
2020-05-02 10:06 ` [PATCH v7 12/22] sifive: dts: fu540: Enable gpio in U-Boot SPL Pragnesh Patel
` (11 subsequent siblings)
22 siblings, 0 replies; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-02 10:06 UTC (permalink / raw)
To: u-boot
This sync has changes required to use GPIO in U-Boot and
U-Boot SPL.
Sync dts from linux v5.7-rc2 commit:
"riscv: dts: Add GPIO reboot method to HiFive Unleashed DTS file"
(sha1: 0a91330b2af9f71ceeeed483f92774182b58f6d9)
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
---
arch/riscv/dts/fu540-c000.dtsi | 37 ++++++++++++++++++++++++-
arch/riscv/dts/hifive-unleashed-a00.dts | 9 ++++++
2 files changed, 45 insertions(+), 1 deletion(-)
diff --git a/arch/riscv/dts/fu540-c000.dtsi b/arch/riscv/dts/fu540-c000.dtsi
index afa43c7ea3..7db8610534 100644
--- a/arch/riscv/dts/fu540-c000.dtsi
+++ b/arch/riscv/dts/fu540-c000.dtsi
@@ -54,6 +54,7 @@
reg = <1>;
riscv,isa = "rv64imafdc";
tlb-split;
+ next-level-cache = <&l2cache>;
cpu1_intc: interrupt-controller {
#interrupt-cells = <1>;
compatible = "riscv,cpu-intc";
@@ -77,6 +78,7 @@
reg = <2>;
riscv,isa = "rv64imafdc";
tlb-split;
+ next-level-cache = <&l2cache>;
cpu2_intc: interrupt-controller {
#interrupt-cells = <1>;
compatible = "riscv,cpu-intc";
@@ -100,6 +102,7 @@
reg = <3>;
riscv,isa = "rv64imafdc";
tlb-split;
+ next-level-cache = <&l2cache>;
cpu3_intc: interrupt-controller {
#interrupt-cells = <1>;
compatible = "riscv,cpu-intc";
@@ -123,6 +126,7 @@
reg = <4>;
riscv,isa = "rv64imafdc";
tlb-split;
+ next-level-cache = <&l2cache>;
cpu4_intc: interrupt-controller {
#interrupt-cells = <1>;
compatible = "riscv,cpu-intc";
@@ -162,6 +166,13 @@
clocks = <&prci PRCI_CLK_TLCLK>;
status = "disabled";
};
+ dma: dma at 3000000 {
+ compatible = "sifive,fu540-c000-pdma";
+ reg = <0x0 0x3000000 0x0 0x8000>;
+ interrupt-parent = <&plic0>;
+ interrupts = <23 24 25 26 27 28 29 30>;
+ #dma-cells = <1>;
+ };
uart1: serial at 10011000 {
compatible = "sifive,fu540-c000-uart", "sifive,uart0";
reg = <0x0 0x10011000 0x0 0x1000>;
@@ -246,6 +257,30 @@
#pwm-cells = <3>;
status = "disabled";
};
-
+ l2cache: cache-controller at 2010000 {
+ compatible = "sifive,fu540-c000-ccache", "cache";
+ cache-block-size = <64>;
+ cache-level = <2>;
+ cache-sets = <1024>;
+ cache-size = <2097152>;
+ cache-unified;
+ interrupt-parent = <&plic0>;
+ interrupts = <1 2 3>;
+ reg = <0x0 0x2010000 0x0 0x1000>;
+ };
+ gpio: gpio at 10060000 {
+ compatible = "sifive,fu540-c000-gpio", "sifive,gpio0";
+ interrupt-parent = <&plic0>;
+ interrupts = <7>, <8>, <9>, <10>, <11>, <12>, <13>,
+ <14>, <15>, <16>, <17>, <18>, <19>, <20>,
+ <21>, <22>;
+ reg = <0x0 0x10060000 0x0 0x1000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&prci PRCI_CLK_TLCLK>;
+ status = "disabled";
+ };
};
};
diff --git a/arch/riscv/dts/hifive-unleashed-a00.dts b/arch/riscv/dts/hifive-unleashed-a00.dts
index 88cfcb96bf..4a2729f5ca 100644
--- a/arch/riscv/dts/hifive-unleashed-a00.dts
+++ b/arch/riscv/dts/hifive-unleashed-a00.dts
@@ -2,6 +2,7 @@
/* Copyright (c) 2018-2019 SiFive, Inc */
#include "fu540-c000.dtsi"
+#include <dt-bindings/gpio/gpio.h>
/* Clock frequency (in Hz) of the PCB crystal for rtcclk */
#define RTCCLK_FREQ 1000000
@@ -41,6 +42,10 @@
clock-frequency = <RTCCLK_FREQ>;
clock-output-names = "rtcclk";
};
+ gpio-restart {
+ compatible = "gpio-restart";
+ gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
+ };
};
&uart0 {
@@ -94,3 +99,7 @@
&pwm1 {
status = "okay";
};
+
+&gpio {
+ status = "okay";
+};
--
2.17.1
^ permalink raw reply related [flat|nested] 118+ messages in thread
* [PATCH v7 12/22] sifive: dts: fu540: Enable gpio in U-Boot SPL
2020-05-02 10:06 [PATCH v7 00/22] RISC-V SiFive FU540 support SPL Pragnesh Patel
` (10 preceding siblings ...)
2020-05-02 10:06 ` [PATCH v7 11/22] riscv: dts: sifive: Sync hifive-unleashed-a00 dts from linux Pragnesh Patel
@ 2020-05-02 10:06 ` Pragnesh Patel
2020-05-02 10:06 ` [PATCH v7 13/22] riscv: cpu: fu540: Add support for cpu fu540 Pragnesh Patel
` (10 subsequent siblings)
22 siblings, 0 replies; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-02 10:06 UTC (permalink / raw)
To: u-boot
Add gpio node for U-Boot SPL
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
---
arch/riscv/dts/hifive-unleashed-a00-u-boot.dtsi | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/riscv/dts/hifive-unleashed-a00-u-boot.dtsi b/arch/riscv/dts/hifive-unleashed-a00-u-boot.dtsi
index 9787332bf1..d55ca43411 100644
--- a/arch/riscv/dts/hifive-unleashed-a00-u-boot.dtsi
+++ b/arch/riscv/dts/hifive-unleashed-a00-u-boot.dtsi
@@ -26,3 +26,7 @@
u-boot,dm-spl;
};
};
+
+&gpio {
+ u-boot,dm-spl;
+};
--
2.17.1
^ permalink raw reply related [flat|nested] 118+ messages in thread
* [PATCH v7 13/22] riscv: cpu: fu540: Add support for cpu fu540
2020-05-02 10:06 [PATCH v7 00/22] RISC-V SiFive FU540 support SPL Pragnesh Patel
` (11 preceding siblings ...)
2020-05-02 10:06 ` [PATCH v7 12/22] sifive: dts: fu540: Enable gpio in U-Boot SPL Pragnesh Patel
@ 2020-05-02 10:06 ` Pragnesh Patel
2020-05-02 12:32 ` Bin Meng
2020-05-02 16:34 ` Jagan Teki
2020-05-02 10:06 ` [PATCH v7 14/22] riscv: Add place-holder for driver compilation Pragnesh Patel
` (9 subsequent siblings)
22 siblings, 2 replies; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-02 10:06 UTC (permalink / raw)
To: u-boot
Add SiFive fu540 cpu to support RISC-V arch
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
---
arch/riscv/Kconfig | 1 +
arch/riscv/cpu/fu540/Kconfig | 15 ++++++++++++++
arch/riscv/cpu/fu540/Makefile | 7 +++++++
arch/riscv/cpu/fu540/cpu.c | 22 ++++++++++++++++++++
arch/riscv/cpu/fu540/dram.c | 38 +++++++++++++++++++++++++++++++++++
5 files changed, 83 insertions(+)
create mode 100644 arch/riscv/cpu/fu540/Kconfig
create mode 100644 arch/riscv/cpu/fu540/Makefile
create mode 100644 arch/riscv/cpu/fu540/cpu.c
create mode 100644 arch/riscv/cpu/fu540/dram.c
diff --git a/arch/riscv/Kconfig b/arch/riscv/Kconfig
index fb5fe5afff..3044609971 100644
--- a/arch/riscv/Kconfig
+++ b/arch/riscv/Kconfig
@@ -57,6 +57,7 @@ source "board/sifive/fu540/Kconfig"
# platform-specific options below
source "arch/riscv/cpu/ax25/Kconfig"
source "arch/riscv/cpu/generic/Kconfig"
+source "arch/riscv/cpu/fu540/Kconfig"
# architecture-specific options below
diff --git a/arch/riscv/cpu/fu540/Kconfig b/arch/riscv/cpu/fu540/Kconfig
new file mode 100644
index 0000000000..b2cb155d6d
--- /dev/null
+++ b/arch/riscv/cpu/fu540/Kconfig
@@ -0,0 +1,15 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# Copyright (C) 2018, Bin Meng <bmeng.cn@gmail.com>
+
+config GENERIC_RISCV
+ bool
+ select ARCH_EARLY_INIT_R
+ imply CPU
+ imply CPU_RISCV
+ imply RISCV_TIMER
+ imply SIFIVE_CLINT if (RISCV_MMODE || SPL_RISCV_MMODE)
+ imply CMD_CPU
+ imply SPL_CPU_SUPPORT
+ imply SPL_OPENSBI
+ imply SPL_LOAD_FIT
diff --git a/arch/riscv/cpu/fu540/Makefile b/arch/riscv/cpu/fu540/Makefile
new file mode 100644
index 0000000000..44700d998c
--- /dev/null
+++ b/arch/riscv/cpu/fu540/Makefile
@@ -0,0 +1,7 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# Copyright (C) 2020 SiFive, Inc
+# Pragnesh Patel <pragnesh.patel@sifive.com>
+
+obj-y += dram.o
+obj-y += cpu.o
diff --git a/arch/riscv/cpu/fu540/cpu.c b/arch/riscv/cpu/fu540/cpu.c
new file mode 100644
index 0000000000..13a69ef0cc
--- /dev/null
+++ b/arch/riscv/cpu/fu540/cpu.c
@@ -0,0 +1,22 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018, Bin Meng <bmeng.cn@gmail.com>
+ */
+
+#include <common.h>
+#include <irq_func.h>
+
+/*
+ * cleanup_before_linux() is called just before we call linux
+ * it prepares the processor for linux
+ *
+ * we disable interrupt and caches.
+ */
+int cleanup_before_linux(void)
+{
+ disable_interrupts();
+
+ cache_flush();
+
+ return 0;
+}
diff --git a/arch/riscv/cpu/fu540/dram.c b/arch/riscv/cpu/fu540/dram.c
new file mode 100644
index 0000000000..1dc77efeca
--- /dev/null
+++ b/arch/riscv/cpu/fu540/dram.c
@@ -0,0 +1,38 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018, Bin Meng <bmeng.cn@gmail.com>
+ */
+
+#include <common.h>
+#include <fdtdec.h>
+#include <init.h>
+#include <linux/sizes.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int dram_init(void)
+{
+ return fdtdec_setup_mem_size_base();
+}
+
+int dram_init_banksize(void)
+{
+ return fdtdec_setup_memory_banksize();
+}
+
+ulong board_get_usable_ram_top(ulong total_size)
+{
+#ifdef CONFIG_64BIT
+ /*
+ * Ensure that we run from first 4GB so that all
+ * addresses used by U-Boot are 32bit addresses.
+ *
+ * This in-turn ensures that 32bit DMA capable
+ * devices work fine because DMA mapping APIs will
+ * provide 32bit DMA addresses only.
+ */
+ if (gd->ram_top > SZ_4G)
+ return SZ_4G;
+#endif
+ return gd->ram_top;
+}
--
2.17.1
^ permalink raw reply related [flat|nested] 118+ messages in thread
* [PATCH v7 14/22] riscv: Add place-holder for driver compilation
2020-05-02 10:06 [PATCH v7 00/22] RISC-V SiFive FU540 support SPL Pragnesh Patel
` (12 preceding siblings ...)
2020-05-02 10:06 ` [PATCH v7 13/22] riscv: cpu: fu540: Add support for cpu fu540 Pragnesh Patel
@ 2020-05-02 10:06 ` Pragnesh Patel
2020-05-02 12:43 ` Bin Meng
2020-05-02 16:27 ` Jagan Teki
2020-05-02 10:06 ` [PATCH v7 15/22] riscv: sifive: dts: fu540: Add clock for cpus node Pragnesh Patel
` (8 subsequent siblings)
22 siblings, 2 replies; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-02 10:06 UTC (permalink / raw)
To: u-boot
Add place-holder for RISC-V fu540 CPU
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
---
arch/riscv/include/asm/arch-fu540/clk.h | 14 +++++++++
arch/riscv/include/asm/arch-fu540/gpio.h | 38 ++++++++++++++++++++++++
2 files changed, 52 insertions(+)
create mode 100644 arch/riscv/include/asm/arch-fu540/clk.h
create mode 100644 arch/riscv/include/asm/arch-fu540/gpio.h
diff --git a/arch/riscv/include/asm/arch-fu540/clk.h b/arch/riscv/include/asm/arch-fu540/clk.h
new file mode 100644
index 0000000000..d71ed4357c
--- /dev/null
+++ b/arch/riscv/include/asm/arch-fu540/clk.h
@@ -0,0 +1,14 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (c) 2020 SiFive Inc
+ *
+ * Authors:
+ * Pragnesh Patel <pragnesh.patel@sifive.com>
+ */
+
+#ifndef __CLK_SIFIVE_H
+#define __CLK_SIFIVE_H
+
+/* Note: This is a placeholder header for driver compilation. */
+
+#endif
diff --git a/arch/riscv/include/asm/arch-fu540/gpio.h b/arch/riscv/include/asm/arch-fu540/gpio.h
new file mode 100644
index 0000000000..0d16c59ca6
--- /dev/null
+++ b/arch/riscv/include/asm/arch-fu540/gpio.h
@@ -0,0 +1,38 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2019 SiFive, Inc.
+ */
+
+#ifndef _GPIO_SIFIVE_H
+#define _GPIO_SIFIVE_H
+
+#define GPIO_INPUT_VAL 0x00
+#define GPIO_INPUT_EN 0x04
+#define GPIO_OUTPUT_EN 0x08
+#define GPIO_OUTPUT_VAL 0x0C
+#define GPIO_RISE_IE 0x18
+#define GPIO_RISE_IP 0x1C
+#define GPIO_FALL_IE 0x20
+#define GPIO_FALL_IP 0x24
+#define GPIO_HIGH_IE 0x28
+#define GPIO_HIGH_IP 0x2C
+#define GPIO_LOW_IE 0x30
+#define GPIO_LOW_IP 0x34
+#define GPIO_OUTPUT_XOR 0x40
+
+#define NR_GPIOS 16
+
+enum gpio_state {
+ LOW,
+ HIGH
+};
+
+/* Details about a GPIO bank */
+struct sifive_gpio_platdata {
+ void *base; /* address of registers in physical memory */
+};
+
+#define SIFIVE_GENERIC_GPIO_NR(port, index) \
+ (((port) * NR_GPIOS) + ((index) & (NR_GPIOS - 1)))
+
+#endif /* _GPIO_SIFIVE_H */
--
2.17.1
^ permalink raw reply related [flat|nested] 118+ messages in thread
* [PATCH v7 15/22] riscv: sifive: dts: fu540: Add clock for cpus node
2020-05-02 10:06 [PATCH v7 00/22] RISC-V SiFive FU540 support SPL Pragnesh Patel
` (13 preceding siblings ...)
2020-05-02 10:06 ` [PATCH v7 14/22] riscv: Add place-holder for driver compilation Pragnesh Patel
@ 2020-05-02 10:06 ` Pragnesh Patel
2020-05-02 12:43 ` Bin Meng
2020-05-02 16:50 ` Jagan Teki
2020-05-02 10:06 ` [PATCH v7 16/22] riscv: Enable cpu clock if it is present Pragnesh Patel
` (7 subsequent siblings)
22 siblings, 2 replies; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-02 10:06 UTC (permalink / raw)
To: u-boot
Add clock-frequency and clocks in cpus node, so that
clock will be enabled by cpu driver.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
---
arch/riscv/dts/fu540-c000-u-boot.dtsi | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/arch/riscv/dts/fu540-c000-u-boot.dtsi b/arch/riscv/dts/fu540-c000-u-boot.dtsi
index e93b8a9bcf..ab697ab93c 100644
--- a/arch/riscv/dts/fu540-c000-u-boot.dtsi
+++ b/arch/riscv/dts/fu540-c000-u-boot.dtsi
@@ -7,6 +7,8 @@
cpus {
u-boot,dm-spl;
cpu0: cpu at 0 {
+ clocks = <&prci PRCI_CLK_COREPLL>;
+ clock-frequency = <1000000000>;
u-boot,dm-spl;
status = "okay";
cpu0_intc: interrupt-controller {
@@ -14,24 +16,32 @@
};
};
cpu1: cpu at 1 {
+ clocks = <&prci PRCI_CLK_COREPLL>;
+ clock-frequency = <1000000000>;
u-boot,dm-spl;
cpu1_intc: interrupt-controller {
u-boot,dm-spl;
};
};
cpu2: cpu at 2 {
+ clocks = <&prci PRCI_CLK_COREPLL>;
+ clock-frequency = <1000000000>;
u-boot,dm-spl;
cpu2_intc: interrupt-controller {
u-boot,dm-spl;
};
};
cpu3: cpu at 3 {
+ clocks = <&prci PRCI_CLK_COREPLL>;
+ clock-frequency = <1000000000>;
u-boot,dm-spl;
cpu3_intc: interrupt-controller {
u-boot,dm-spl;
};
};
cpu4: cpu at 4 {
+ clocks = <&prci PRCI_CLK_COREPLL>;
+ clock-frequency = <1000000000>;
u-boot,dm-spl;
cpu4_intc: interrupt-controller {
u-boot,dm-spl;
--
2.17.1
^ permalink raw reply related [flat|nested] 118+ messages in thread
* [PATCH v7 16/22] riscv: Enable cpu clock if it is present
2020-05-02 10:06 [PATCH v7 00/22] RISC-V SiFive FU540 support SPL Pragnesh Patel
` (14 preceding siblings ...)
2020-05-02 10:06 ` [PATCH v7 15/22] riscv: sifive: dts: fu540: Add clock for cpus node Pragnesh Patel
@ 2020-05-02 10:06 ` Pragnesh Patel
2020-05-02 12:55 ` Bin Meng
2020-05-02 18:15 ` Sean Anderson
2020-05-02 10:06 ` [PATCH v7 17/22] riscv: sifive: fu540: add SPL configuration Pragnesh Patel
` (6 subsequent siblings)
22 siblings, 2 replies; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-02 10:06 UTC (permalink / raw)
To: u-boot
The cpu clock is probably already enabled if we are executing code (though
we could be executing from a different core). This patch prevents the cpu
clock or its parents from being disabled.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
---
drivers/cpu/riscv_cpu.c | 33 +++++++++++++++++++++++++++++++++
1 file changed, 33 insertions(+)
diff --git a/drivers/cpu/riscv_cpu.c b/drivers/cpu/riscv_cpu.c
index 28ad0aa30f..8ebe0341fd 100644
--- a/drivers/cpu/riscv_cpu.c
+++ b/drivers/cpu/riscv_cpu.c
@@ -9,6 +9,7 @@
#include <errno.h>
#include <dm/device-internal.h>
#include <dm/lists.h>
+#include <clk.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -100,6 +101,37 @@ static int riscv_cpu_bind(struct udevice *dev)
return 0;
}
+static int riscv_cpu_probe(struct udevice *dev)
+{
+ int ret = 0;
+ u32 clock = 0;
+ struct clk clk;
+
+ /* Get a clock if it exists */
+ ret = clk_get_by_index(dev, 0, &clk);
+ if (ret)
+ return 0;
+
+ ret = dev_read_u32(dev, "clock-frequency", &clock);
+ if (ret) {
+ debug("clock-frequency not found in dt %d\n", ret);
+ return ret;
+ } else {
+ ret = clk_set_rate(&clk, clock);
+ if (ret < 0) {
+ debug("Could not set CPU clock\n");
+ return ret;
+ }
+ }
+
+ ret = clk_enable(&clk);
+ clk_free(&clk);
+ if (ret == -ENOSYS || ret == -ENOTSUPP)
+ return 0;
+ else
+ return ret;
+}
+
static const struct cpu_ops riscv_cpu_ops = {
.get_desc = riscv_cpu_get_desc,
.get_info = riscv_cpu_get_info,
@@ -116,6 +148,7 @@ U_BOOT_DRIVER(riscv_cpu) = {
.id = UCLASS_CPU,
.of_match = riscv_cpu_ids,
.bind = riscv_cpu_bind,
+ .probe = riscv_cpu_probe,
.ops = &riscv_cpu_ops,
.flags = DM_FLAG_PRE_RELOC,
};
--
2.17.1
^ permalink raw reply related [flat|nested] 118+ messages in thread
* [PATCH v7 17/22] riscv: sifive: fu540: add SPL configuration
2020-05-02 10:06 [PATCH v7 00/22] RISC-V SiFive FU540 support SPL Pragnesh Patel
` (15 preceding siblings ...)
2020-05-02 10:06 ` [PATCH v7 16/22] riscv: Enable cpu clock if it is present Pragnesh Patel
@ 2020-05-02 10:06 ` Pragnesh Patel
2020-05-02 12:55 ` Bin Meng
2020-05-02 10:06 ` [PATCH v7 18/22] configs: fu540: Add config options for U-Boot SPL Pragnesh Patel
` (5 subsequent siblings)
22 siblings, 1 reply; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-02 10:06 UTC (permalink / raw)
To: u-boot
Add a support for SPL which will boot from L2 LIM (0x0800_0000) and
then SPL will boot U-Boot FIT image (OpenSBI FW_DYNAMIC + u-boot.bin)
from MMC boot devices.
SPL related code is leveraged from FSBL
(https://github.com/sifive/freedom-u540-c000-bootloader.git)
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
---
arch/riscv/cpu/fu540/Makefile | 4 ++
arch/riscv/cpu/fu540/spl.c | 23 ++++++
.../dts/hifive-unleashed-a00-u-boot.dtsi | 1 +
arch/riscv/include/asm/arch-fu540/spl.h | 14 ++++
board/sifive/fu540/Kconfig | 10 ++-
board/sifive/fu540/Makefile | 4 ++
board/sifive/fu540/fu540.c | 24 +++++++
board/sifive/fu540/spl.c | 72 +++++++++++++++++++
include/configs/sifive-fu540.h | 18 +++++
9 files changed, 169 insertions(+), 1 deletion(-)
create mode 100644 arch/riscv/cpu/fu540/spl.c
create mode 100644 arch/riscv/include/asm/arch-fu540/spl.h
create mode 100644 board/sifive/fu540/spl.c
diff --git a/arch/riscv/cpu/fu540/Makefile b/arch/riscv/cpu/fu540/Makefile
index 44700d998c..043fb961a5 100644
--- a/arch/riscv/cpu/fu540/Makefile
+++ b/arch/riscv/cpu/fu540/Makefile
@@ -3,5 +3,9 @@
# Copyright (C) 2020 SiFive, Inc
# Pragnesh Patel <pragnesh.patel@sifive.com>
+ifeq ($(CONFIG_SPL_BUILD),y)
+obj-y += spl.o
+else
obj-y += dram.o
obj-y += cpu.o
+endif
diff --git a/arch/riscv/cpu/fu540/spl.c b/arch/riscv/cpu/fu540/spl.c
new file mode 100644
index 0000000000..2e05d8a6e2
--- /dev/null
+++ b/arch/riscv/cpu/fu540/spl.c
@@ -0,0 +1,23 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2020 SiFive, Inc
+ * Pragnesh Patel <pragnesh.patel@sifive.com>
+ */
+
+#include <common.h>
+#include <dm.h>
+
+int soc_spl_init(void)
+{
+ int ret;
+ struct udevice *dev;
+
+ /* DDR init */
+ ret = uclass_get_device(UCLASS_RAM, 0, &dev);
+ if (ret) {
+ debug("DRAM init failed: %d\n", ret);
+ return ret;
+ }
+
+ return 0;
+}
diff --git a/arch/riscv/dts/hifive-unleashed-a00-u-boot.dtsi b/arch/riscv/dts/hifive-unleashed-a00-u-boot.dtsi
index d55ca43411..37de015de6 100644
--- a/arch/riscv/dts/hifive-unleashed-a00-u-boot.dtsi
+++ b/arch/riscv/dts/hifive-unleashed-a00-u-boot.dtsi
@@ -4,6 +4,7 @@
*/
#include "fu540-c000-u-boot.dtsi"
+#include "fu540-hifive-unleashed-a00-sdram-ddr4.dtsi"
/ {
aliases {
diff --git a/arch/riscv/include/asm/arch-fu540/spl.h b/arch/riscv/include/asm/arch-fu540/spl.h
new file mode 100644
index 0000000000..0c188be747
--- /dev/null
+++ b/arch/riscv/include/asm/arch-fu540/spl.h
@@ -0,0 +1,14 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2020 SiFive, Inc.
+ *
+ * Authors:
+ * Pragnesh Patel <pragnesh.patel@sifve.com>
+ */
+
+#ifndef _SPL_SIFIVE_H
+#define _SPL_SIFIVE_H
+
+int soc_spl_init(void);
+
+#endif /* _SPL_SIFIVE_H */
diff --git a/board/sifive/fu540/Kconfig b/board/sifive/fu540/Kconfig
index d41c305227..f547b11f9a 100644
--- a/board/sifive/fu540/Kconfig
+++ b/board/sifive/fu540/Kconfig
@@ -7,18 +7,26 @@ config SYS_VENDOR
default "sifive"
config SYS_CPU
- default "generic"
+ default "fu540"
config SYS_CONFIG_NAME
default "sifive-fu540"
config SYS_TEXT_BASE
+ default 0x80200000 if SPL
default 0x80000000 if !RISCV_SMODE
default 0x80200000 if RISCV_SMODE
+config SPL_TEXT_BASE
+ default 0x08000000
+
+config SPL_OPENSBI_LOAD_ADDR
+ default 0x80000000
+
config BOARD_SPECIFIC_OPTIONS # dummy
def_bool y
select GENERIC_RISCV
+ select SUPPORT_SPL
select RAM
select SPL_RAM if SPL
imply CMD_DHCP
diff --git a/board/sifive/fu540/Makefile b/board/sifive/fu540/Makefile
index 6e1862c475..b05e2f5807 100644
--- a/board/sifive/fu540/Makefile
+++ b/board/sifive/fu540/Makefile
@@ -3,3 +3,7 @@
# Copyright (c) 2019 Western Digital Corporation or its affiliates.
obj-y += fu540.o
+
+ifdef CONFIG_SPL_BUILD
+obj-y += spl.o
+endif
diff --git a/board/sifive/fu540/fu540.c b/board/sifive/fu540/fu540.c
index 540638c919..d05529a86b 100644
--- a/board/sifive/fu540/fu540.c
+++ b/board/sifive/fu540/fu540.c
@@ -11,6 +11,7 @@
#include <linux/delay.h>
#include <linux/io.h>
#include <misc.h>
+#include <spl.h>
/*
* This define is a value used for error/unknown serial.
@@ -114,3 +115,26 @@ int board_init(void)
return 0;
}
+
+#ifdef CONFIG_SPL
+void board_boot_order(u32 *spl_boot_list)
+{
+ u8 i;
+ u32 boot_devices[] = {
+#ifdef CONFIG_SPL_MMC_SUPPORT
+ BOOT_DEVICE_MMC1,
+#endif
+ };
+
+ for (i = 0; i < ARRAY_SIZE(boot_devices); i++)
+ spl_boot_list[i] = boot_devices[i];
+}
+#endif
+
+#ifdef CONFIG_SPL_LOAD_FIT
+int board_fit_config_name_match(const char *name)
+{
+ /* boot using first FIT config */
+ return 0;
+}
+#endif
diff --git a/board/sifive/fu540/spl.c b/board/sifive/fu540/spl.c
new file mode 100644
index 0000000000..b3ff6850e3
--- /dev/null
+++ b/board/sifive/fu540/spl.c
@@ -0,0 +1,72 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (c) 2019 SiFive, Inc
+ *
+ * Authors:
+ * Pragnesh Patel <pragnesh.patel@sifive.com>
+ */
+
+#include <common.h>
+#include <spl.h>
+#include <misc.h>
+#include <asm/gpio.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/spl.h>
+
+#define GEM_PHY_RESET SIFIVE_GENERIC_GPIO_NR(0, 12)
+
+int init_clk_and_ddr(void)
+{
+ int ret;
+
+ ret = soc_spl_init();
+ if (ret) {
+ debug("FU540 SPL init failed: %d\n", ret);
+ return ret;
+ }
+
+ /*
+ * GEMGXL init VSC8541 PHY reset sequence;
+ * leave pull-down active for 2ms
+ */
+ udelay(2000);
+ ret = gpio_request(GEM_PHY_RESET, "gem_phy_reset");
+ if (ret) {
+ debug("gem_phy_reset gpio request failed: %d\n", ret);
+ return ret;
+ }
+
+ /* Set GPIO 12 (PHY NRESET) */
+ ret = gpio_direction_output(GEM_PHY_RESET, 1);
+ if (ret) {
+ debug("gem_phy_reset gpio direction set failed: %d\n", ret);
+ return ret;
+ }
+
+ udelay(1);
+
+ /* Reset PHY again to enter unmanaged mode */
+ gpio_set_value(GEM_PHY_RESET, 0);
+ udelay(1);
+ gpio_set_value(GEM_PHY_RESET, 1);
+ mdelay(15);
+
+ return 0;
+}
+
+void board_init_f(ulong dummy)
+{
+ int ret;
+
+ ret = spl_early_init();
+ if (ret)
+ panic("spl_early_init() failed: %d\n", ret);
+
+ arch_cpu_init_dm();
+
+ preloader_console_init();
+
+ ret = init_clk_and_ddr();
+ if (ret)
+ panic("init_clk_and_ddr() failed: %d\n", ret);
+}
diff --git a/include/configs/sifive-fu540.h b/include/configs/sifive-fu540.h
index 2756ed5a77..ef3ae9b650 100644
--- a/include/configs/sifive-fu540.h
+++ b/include/configs/sifive-fu540.h
@@ -11,6 +11,22 @@
#include <linux/sizes.h>
+#ifdef CONFIG_SPL
+
+#define CONFIG_SPL_MAX_SIZE 0x00100000
+#define CONFIG_SPL_BSS_START_ADDR 0x85000000
+#define CONFIG_SPL_BSS_MAX_SIZE 0x00100000
+#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \
+ CONFIG_SPL_BSS_MAX_SIZE)
+#define CONFIG_SYS_SPL_MALLOC_SIZE 0x00100000
+
+#define CONFIG_SPL_LOAD_FIT_ADDRESS 0x84000000
+
+#define CONFIG_SPL_STACK (0x08000000 + 0x001D0000 - \
+ GENERATED_GBL_DATA_SIZE)
+
+#endif
+
#define CONFIG_SYS_SDRAM_BASE 0x80000000
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + SZ_2M)
@@ -24,6 +40,7 @@
/* Environment options */
+#ifndef CONFIG_SPL_BUILD
#define BOOT_TARGET_DEVICES(func) \
func(MMC, mmc, 0) \
func(DHCP, dhcp, na)
@@ -43,5 +60,6 @@
#define CONFIG_PREBOOT \
"setenv fdt_addr ${fdtcontroladdr};" \
"fdt addr ${fdtcontroladdr};"
+#endif
#endif /* __CONFIG_H */
--
2.17.1
^ permalink raw reply related [flat|nested] 118+ messages in thread
* [PATCH v7 18/22] configs: fu540: Add config options for U-Boot SPL
2020-05-02 10:06 [PATCH v7 00/22] RISC-V SiFive FU540 support SPL Pragnesh Patel
` (16 preceding siblings ...)
2020-05-02 10:06 ` [PATCH v7 17/22] riscv: sifive: fu540: add SPL configuration Pragnesh Patel
@ 2020-05-02 10:06 ` Pragnesh Patel
2020-05-02 12:55 ` Bin Meng
` (2 more replies)
2020-05-02 10:06 ` [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot Pragnesh Patel
` (4 subsequent siblings)
22 siblings, 3 replies; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-02 10:06 UTC (permalink / raw)
To: u-boot
With sifive_fu540_defconfig:
User can use FSBL or u-boot-spl.bin anyone at a time.
For FSBL,
fsbl->fw_payload.bin (opensbi + U-Boot)
For u-boot-spl.bin,
u-boot-spl.bin->FIT image (opensbi + U-Boot + dtb)
U-Boot SPL will be loaded by ZSBL from SD card (replace fsbl.bin with
u-boot-spl.bin) and runs in L2 LIM in machine mode and then load FIT
image u-boot.itb from SD card into RAM.
U-Boot SPL expects u-boot.itb FIT image at the starting of SD card sector
number (0x822) of GUID type "2E54B353-1271-4842-806F-E436D6AF6985"
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
---
configs/sifive_fu540_defconfig | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/configs/sifive_fu540_defconfig b/configs/sifive_fu540_defconfig
index f805aacc7a..30fac8996b 100644
--- a/configs/sifive_fu540_defconfig
+++ b/configs/sifive_fu540_defconfig
@@ -1,6 +1,12 @@
CONFIG_RISCV=y
+CONFIG_SPL_GPIO_SUPPORT=y
+CONFIG_SYS_MALLOC_F_LEN=0x3000
CONFIG_ENV_SIZE=0x20000
+CONFIG_SPL_MMC_SUPPORT=y
CONFIG_NR_DRAM_BANKS=1
+CONFIG_SPL=y
+CONFIG_SPL_SPI_SUPPORT=y
+CONFIG_SPL_PAYLOAD="u-boot.itb"
CONFIG_TARGET_SIFIVE_FU540=y
CONFIG_ARCH_RV64I=y
CONFIG_RISCV_SMODE=y
@@ -9,7 +15,10 @@ CONFIG_FIT=y
CONFIG_MISC_INIT_R=y
CONFIG_DISPLAY_CPUINFO=y
CONFIG_DISPLAY_BOARDINFO=y
+CONFIG_SPL_SEPARATE_BSS=y
+CONFIG_SPL_YMODEM_SUPPORT=y
CONFIG_OF_BOARD_FIXUP=y
CONFIG_DEFAULT_DEVICE_TREE="hifive-unleashed-a00"
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_SPL_CLK=y
CONFIG_DM_MTD=y
--
2.17.1
^ permalink raw reply related [flat|nested] 118+ messages in thread
* [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
2020-05-02 10:06 [PATCH v7 00/22] RISC-V SiFive FU540 support SPL Pragnesh Patel
` (17 preceding siblings ...)
2020-05-02 10:06 ` [PATCH v7 18/22] configs: fu540: Add config options for U-Boot SPL Pragnesh Patel
@ 2020-05-02 10:06 ` Pragnesh Patel
2020-05-02 16:18 ` Jagan Teki
2020-05-02 10:06 ` [PATCH v7 20/22] riscv: sifive: fu540: enable all cache ways from U-Boot proper Pragnesh Patel
` (3 subsequent siblings)
22 siblings, 1 reply; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-02 10:06 UTC (permalink / raw)
To: u-boot
Add L2 cache node to enable cache ways from U-Boot
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
---
arch/riscv/dts/fu540-c000-u-boot.dtsi | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/riscv/dts/fu540-c000-u-boot.dtsi b/arch/riscv/dts/fu540-c000-u-boot.dtsi
index ab697ab93c..3c3b810998 100644
--- a/arch/riscv/dts/fu540-c000-u-boot.dtsi
+++ b/arch/riscv/dts/fu540-c000-u-boot.dtsi
@@ -85,3 +85,7 @@
&qspi2 {
u-boot,dm-spl;
};
+
+&l2cache {
+ status = "okay";
+};
--
2.17.1
^ permalink raw reply related [flat|nested] 118+ messages in thread
* [PATCH v7 20/22] riscv: sifive: fu540: enable all cache ways from U-Boot proper
2020-05-02 10:06 [PATCH v7 00/22] RISC-V SiFive FU540 support SPL Pragnesh Patel
` (18 preceding siblings ...)
2020-05-02 10:06 ` [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot Pragnesh Patel
@ 2020-05-02 10:06 ` Pragnesh Patel
2020-05-02 12:55 ` Bin Meng
2020-05-02 10:06 ` [PATCH v7 21/22] doc: sifive: fu540: Add description for OpenSBI generic platform Pragnesh Patel
` (2 subsequent siblings)
22 siblings, 1 reply; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-02 10:06 UTC (permalink / raw)
To: u-boot
Enable all cache ways from U-Boot proper.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
---
arch/riscv/cpu/fu540/Makefile | 1 +
arch/riscv/cpu/fu540/cache.c | 53 +++++++++++++++++++++++
arch/riscv/include/asm/arch-fu540/cache.h | 14 ++++++
board/sifive/fu540/fu540.c | 10 ++++-
4 files changed, 76 insertions(+), 2 deletions(-)
create mode 100644 arch/riscv/cpu/fu540/cache.c
create mode 100644 arch/riscv/include/asm/arch-fu540/cache.h
diff --git a/arch/riscv/cpu/fu540/Makefile b/arch/riscv/cpu/fu540/Makefile
index 043fb961a5..088205ef57 100644
--- a/arch/riscv/cpu/fu540/Makefile
+++ b/arch/riscv/cpu/fu540/Makefile
@@ -8,4 +8,5 @@ obj-y += spl.o
else
obj-y += dram.o
obj-y += cpu.o
+obj-y += cache.o
endif
diff --git a/arch/riscv/cpu/fu540/cache.c b/arch/riscv/cpu/fu540/cache.c
new file mode 100644
index 0000000000..d2dae7f17a
--- /dev/null
+++ b/arch/riscv/cpu/fu540/cache.c
@@ -0,0 +1,53 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2020 SiFive, Inc
+ *
+ * Authors:
+ * Pragnesh Patel <pragnesh.patel@sifive.com>
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <linux/bitops.h>
+
+/* Register offsets */
+#define CACHE_CONFIG 0x000
+#define CACHE_ENABLE 0x008
+
+#define MASK_NUM_WAYS GENMASK(15, 8)
+#define NUM_WAYS_SHIFT 8
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int cache_enable_ways(void)
+{
+ const void *blob = gd->fdt_blob;
+ int node = (-FDT_ERR_NOTFOUND);
+ fdt_addr_t base;
+ u32 config;
+ u32 ways;
+
+ volatile u32 *enable;
+
+ node = fdt_node_offset_by_compatible(blob, -1,
+ "sifive,fu540-c000-ccache");
+
+ if (node < 0)
+ return node;
+
+ base = fdtdec_get_addr(blob, node, "reg");
+ if (base == FDT_ADDR_T_NONE)
+ return FDT_ADDR_T_NONE;
+
+ config = readl((volatile u32 *)base + CACHE_CONFIG);
+ ways = (config & MASK_NUM_WAYS) >> NUM_WAYS_SHIFT;
+
+ enable = (volatile u32 *)(base + CACHE_ENABLE);
+
+ /* memory barrier */
+ mb();
+ (*enable) = ways - 1;
+ /* memory barrier */
+ mb();
+ return 0;
+}
diff --git a/arch/riscv/include/asm/arch-fu540/cache.h b/arch/riscv/include/asm/arch-fu540/cache.h
new file mode 100644
index 0000000000..135a17c679
--- /dev/null
+++ b/arch/riscv/include/asm/arch-fu540/cache.h
@@ -0,0 +1,14 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2020 SiFive, Inc.
+ *
+ * Authors:
+ * Pragnesh Patel <pragnesh.patel@sifve.com>
+ */
+
+#ifndef _CACHE_SIFIVE_H
+#define _CACHE_SIFIVE_H
+
+int cache_enable_ways(void);
+
+#endif /* _CACHE_SIFIVE_H */
diff --git a/board/sifive/fu540/fu540.c b/board/sifive/fu540/fu540.c
index d05529a86b..131fee8898 100644
--- a/board/sifive/fu540/fu540.c
+++ b/board/sifive/fu540/fu540.c
@@ -12,6 +12,7 @@
#include <linux/io.h>
#include <misc.h>
#include <spl.h>
+#include <asm/arch/cache.h>
/*
* This define is a value used for error/unknown serial.
@@ -111,8 +112,13 @@ int misc_init_r(void)
int board_init(void)
{
- /* For now nothing to do here. */
-
+ int ret;
+ /* enable all cache ways */
+ ret = cache_enable_ways();
+ if (ret) {
+ debug("%s: could not enable cache ways\n", __func__);
+ return ret;
+ }
return 0;
}
--
2.17.1
^ permalink raw reply related [flat|nested] 118+ messages in thread
* [PATCH v7 21/22] doc: sifive: fu540: Add description for OpenSBI generic platform
2020-05-02 10:06 [PATCH v7 00/22] RISC-V SiFive FU540 support SPL Pragnesh Patel
` (19 preceding siblings ...)
2020-05-02 10:06 ` [PATCH v7 20/22] riscv: sifive: fu540: enable all cache ways from U-Boot proper Pragnesh Patel
@ 2020-05-02 10:06 ` Pragnesh Patel
2020-05-02 12:55 ` Bin Meng
2020-05-02 10:06 ` [PATCH v7 22/22] doc: sifive: fu540: Add description for RISC-V FU540 U-Boot SPL Pragnesh Patel
2020-05-02 17:18 ` [PATCH v7 00/22] RISC-V SiFive FU540 support SPL Jagan Teki
22 siblings, 1 reply; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-02 10:06 UTC (permalink / raw)
To: u-boot
OpenSBI generic platform support provides platform specific
functionality based on the FDT passed by previous booting stage.
depends on OpenSBI commit:
platform: Add generic FDT based platform support
(sha1: f1aa9e54e00006ae70aeac638d5b75093520f65d)
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
---
doc/board/sifive/fu540.rst | 19 +++++++++++++------
1 file changed, 13 insertions(+), 6 deletions(-)
diff --git a/doc/board/sifive/fu540.rst b/doc/board/sifive/fu540.rst
index 610ba87074..1c3d4740f3 100644
--- a/doc/board/sifive/fu540.rst
+++ b/doc/board/sifive/fu540.rst
@@ -22,14 +22,21 @@ The support for following drivers are already enabled:
TODO:
-1. U-Boot expects the serial console device entry to be present under /chosen
- DT node. Without a serial console U-Boot will panic. Example:
+1. The DTB passed by U-Boot SPL or FSBL to OpenSBI should have CLINT
+ DT node and the "/chosen" DT node should have "stdout-path" DT
+ property.
.. code-block:: none
- chosen {
- stdout-path = "/soc/serial at 10010000:115200";
- };
+ chosen {
+ stdout-path = "/soc/serial at 10010000:115200";
+ };
+
+ clint at 2000000 {
+ compatible = "riscv,clint0";
+ interrupts-extended = <&cpu0_intc 3 &cpu0_intc 7 &cpu1_intc 3 &cpu1_intc 7 &cpu2_intc 3 &cpu2_intc 7 &cpu3_intc 3 &cpu3_intc 7 &cpu4_intc 3 &cpu4_intc 7>;
+ reg = <0x0 0x2000000 0x0 0xc0000>;
+ };
Building
--------
@@ -58,7 +65,7 @@ firmware. We need to compile OpenSBI with below command:
.. code-block:: none
-make PLATFORM=sifive/fu540 FW_PAYLOAD_PATH=<path to u-boot-dtb.bin>
+ make PLATFORM=generic FW_PAYLOAD_PATH=<path to u-boot-dtb.bin>
More detailed description of steps required to build FW_PAYLOAD firmware
is beyond the scope of this document. Please refer OpenSBI documenation.
--
2.17.1
^ permalink raw reply related [flat|nested] 118+ messages in thread
* [PATCH v7 22/22] doc: sifive: fu540: Add description for RISC-V FU540 U-Boot SPL
2020-05-02 10:06 [PATCH v7 00/22] RISC-V SiFive FU540 support SPL Pragnesh Patel
` (20 preceding siblings ...)
2020-05-02 10:06 ` [PATCH v7 21/22] doc: sifive: fu540: Add description for OpenSBI generic platform Pragnesh Patel
@ 2020-05-02 10:06 ` Pragnesh Patel
2020-05-02 12:55 ` Bin Meng
` (2 more replies)
2020-05-02 17:18 ` [PATCH v7 00/22] RISC-V SiFive FU540 support SPL Jagan Teki
22 siblings, 3 replies; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-02 10:06 UTC (permalink / raw)
To: u-boot
Add descriptions about U-Boot SPL feature and how to build and run
from MMC.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
doc/board/sifive/fu540.rst | 376 +++++++++++++++++++++++++++++++++++++
1 file changed, 376 insertions(+)
diff --git a/doc/board/sifive/fu540.rst b/doc/board/sifive/fu540.rst
index 1c3d4740f3..2911e3652e 100644
--- a/doc/board/sifive/fu540.rst
+++ b/doc/board/sifive/fu540.rst
@@ -38,6 +38,9 @@ TODO:
reg = <0x0 0x2000000 0x0 0xc0000>;
};
+Booting from MMC using FSBL
+---------------------------
+
Building
--------
@@ -428,3 +431,376 @@ as well.
Please press Enter to activate this console.
/ #
+
+Booting from MMC using U-Boot SPL
+---------------------------------
+
+Building
+--------
+
+Before building U-Boot SPL, OpenSBI must be built first. OpenSBI can be
+cloned and built for FU540 as below:
+
+.. code-block:: console
+
+ git clone https://github.com/riscv/opensbi.git
+ cd opensbi
+ make PLATFORM=generic FW_DYNAMIC=y
+
+Copy OpenSBI FW_DYNAMIC image
+(build/platform/sifive/fu540/firmware/fw_dynamic.bin) into U-Boot
+root directory
+
+.. code-block:: console
+
+ cp build/platform/sifive/fu540/firmware/fw_dynamic.bin <u-boot-dir>
+
+Now build the U-Boot SPL and U-Boot proper
+
+.. code-block:: console
+
+ cd <U-Boot-dir>
+ make sifive_fu540_defconfig
+ make
+
+This will generate spl/u-boot-spl.bin and FIT image (u-boot.itb)
+
+
+Flashing
+--------
+
+ZSBL loads the U-Boot SPL (u-boot-spl.bin) from a partition with GUID type
+5B193300-FC78-40CD-8002-E86C45580B47
+
+U-Boot SPL expects a U-Boot FIT image (u-boot.itb) from a partition with GUID
+type 2E54B353-1271-4842-806F-E436D6AF6985
+
+FIT image (u-boot.itb) is a combination of fw_dynamic.bin, u-boot-nodtb.bin and
+device tree blob (hifive-unleashed-a00.dtb)
+
+Format the SD card (make sure the disk has GPT, otherwise use gdisk to switch)
+
+.. code-block:: none
+
+ # sudo sgdisk --clear \
+ > --set-alignment=2 \
+ > --new=1:34:2081 --change-name=1:loader1 --typecode=1:5B193300-FC78-40CD-8002-E86C45580B47 \
+ > --new=2:2082:10273 --change-name=2:loader2 --typecode=2:2E54B353-1271-4842-806F-E436D6AF6985 \
+ > --new=3:10274: --change-name=3:rootfs --typecode=3:0FC63DAF-8483-4772-8E79-3D69D8477DE4 \
+ > /dev/sda
+
+Program the SD card
+
+.. code-block:: none
+
+ sudo dd if=spl/u-boot-spl.bin of=/dev/sda seek=34
+ sudo dd if=u-boot.itb of=/dev/sda seek=2082
+
+Booting
+-------
+Once you plugin the sdcard and power up, you should see the U-Boot prompt.
+
+Sample boot log from HiFive Unleashed board
+-------------------------------------------
+
+.. code-block:: none
+
+ U-Boot SPL 2020.04-rc2-00109-g63efc7e07e-dirty (Apr 30 2020 - 13:52:36 +0530)
+ Trying to boot from MMC1
+
+
+ U-Boot 2020.04-rc2-00109-g63efc7e07e-dirty (Apr 30 2020 - 13:52:36 +0530)
+
+ CPU: rv64imafdc
+ Model: SiFive HiFive Unleashed A00
+ DRAM: 8 GiB
+ MMC: spi at 10050000:mmc at 0: 0
+ In: serial at 10010000
+ Out: serial at 10010000
+ Err: serial at 10010000
+ Board serial number should not be 0 !!
+ Net:
+ Warning: ethernet at 10090000 (eth0) using random MAC address - 96:06:92:18:eb:04
+ eth0: ethernet at 10090000
+ Hit any key to stop autoboot: 0
+ => version
+ U-Boot 2020.04-rc2-00109-g63efc7e07e-dirty (Apr 30 2020 - 13:52:36 +0530)
+
+ riscv64-unknown-linux-gnu-gcc (crosstool-NG 1.24.0.37-3f461da) 9.2.0
+ GNU ld (crosstool-NG 1.24.0.37-3f461da) 2.32
+ => mmc info
+ Device: spi at 10050000:mmc at 0
+ Manufacturer ID: 3
+ OEM: 5344
+ Name: SC16G
+ Bus Speed: 20000000
+ Mode: SD Legacy
+ Rd Block Len: 512
+ SD version 2.0
+ High Capacity: Yes
+ Capacity: 14.8 GiB
+ Bus Width: 1-bit
+ Erase Group Size: 512 Bytes
+ => mmc part
+
+ Partition Map for MMC device 0 -- Partition Type: EFI
+
+ Part Start LBA End LBA Name
+ Attributes
+ Type GUID
+ Partition GUID
+ 1 0x00000022 0x00000821 "loader1"
+ attrs: 0x0000000000000000
+ type: 5b193300-fc78-40cd-8002-e86c45580b47
+ guid: 66e2b5d2-74db-4df8-ad6f-694b3617f87f
+ 2 0x00000822 0x00002821 "loader2"
+ attrs: 0x0000000000000000
+ type: 2e54b353-1271-4842-806f-e436d6af6985
+ guid: 8befaeaf-bca0-435d-b002-e201f37c0a2f
+ 3 0x00002822 0x01dacbde "rootfs"
+ attrs: 0x0000000000000000
+ type: 0fc63daf-8483-4772-8e79-3d69d8477de4
+ type: linux
+ guid: 9faa81b6-39b1-4418-af5e-89c48f29c20d
+
+Now you can configure your networking, tftp server and use tftp boot method to
+load uImage.
+
+.. code-block:: none
+
+ => setenv serverip 192.168.0.103
+ => setenv serverip 192.168.0.102
+ => tftpboot 0x83000000 fit.itb
+ ethernet at 10090000: PHY present at 0
+ ethernet at 10090000: Starting autonegotiation...
+ ethernet at 10090000: Autonegotiation complete
+ ethernet at 10090000: link up, 100Mbps full-duplex (lpa: 0x4de1)
+ *** ERROR: `ipaddr' not set
+ => setenv serverip 192.168.0.103
+ => setenv ipaddr 192.168.0.102
+ => tftpboot 0x83000000 fit.itb
+ ethernet at 10090000: PHY present at 0
+ ethernet at 10090000: Starting autonegotiation...
+ ethernet at 10090000: Autonegotiation complete
+ ethernet at 10090000: link up, 100Mbps full-duplex (lpa: 0x4de1)
+ Using ethernet at 10090000 device
+ TFTP from server 192.168.0.103; our IP address is 192.168.0.102
+ Filename 'fit.itb'.
+ Load address: 0x83000000
+ Loading: #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #################################################################
+ #######################################################
+ 4.2 MiB/s
+ done
+ Bytes transferred = 14254183 (d98067 hex)
+ => bootm 0x83000000
+ ## Loading kernel from FIT Image at 83000000 ...
+ Using 'config-1' configuration
+ Trying 'kernel at 1' kernel subimage
+ Description: Linux kernel
+ Type: Kernel Image
+ Compression: uncompressed
+ Data Start: 0x830000d8
+ Data Size: 9676752 Bytes = 9.2 MiB
+ Architecture: RISC-V
+ OS: Linux
+ Load Address: 0x80200000
+ Entry Point: 0x80200000
+ Verifying Hash Integrity ... OK
+ ## Loading ramdisk from FIT Image at 83000000 ...
+ Using 'config-1' configuration
+ Trying 'ramdisk at 1' ramdisk subimage
+ Description: ramdisk
+ Type: RAMDisk Image
+ Compression: gzip compressed
+ Data Start: 0x8393c490
+ Data Size: 4568674 Bytes = 4.4 MiB
+ Architecture: RISC-V
+ OS: Linux
+ Load Address: 0x82000000
+ Entry Point: unavailable
+ Verifying Hash Integrity ... OK
+ Loading ramdisk from 0x8393c490 to 0x82000000
+ WARNING: 'compression' nodes for ramdisks are deprecated, please fix your .its file!
+ ## Loading fdt from FIT Image at 83000000 ...
+ Using 'config-1' configuration
+ Trying 'fdt at 1' fdt subimage
+ Description: unavailable
+ Type: Flat Device Tree
+ Compression: uncompressed
+ Data Start: 0x8393a934
+ Data Size: 6889 Bytes = 6.7 KiB
+ Architecture: RISC-V
+ Verifying Hash Integrity ... OK
+ Booting using the fdt blob at 0x8393a934
+ Loading Kernel Image
+ Using Device Tree in place at 000000008393a934, end 000000008393f41c
+
+ Starting kernel ...
+
+ [ 0.000000] OF: fdt: Ignoring memory range 0x80000000 - 0x80200000
+ [ 0.000000] Linux version 5.6.0-rc3-00026-g63623fd44972 (pragneshp at sachinj2-OptiPlex-7010) (gcc version 9.2.0 (crosstool-NG 1.24.0.37-3f461da)) #3 SMP Tue Feb 25 14:59:12 IST 2020
+ [ 0.000000] Initial ramdisk at: 0x(____ptrval____) (4568674 bytes)
+ [ 0.000000] Zone ranges:
+ [ 0.000000] DMA32 [mem 0x0000000080200000-0x00000000ffffffff]
+ [ 0.000000] Normal [mem 0x0000000100000000-0x000000027fffffff]
+ [ 0.000000] Movable zone start for each node
+ [ 0.000000] Early memory node ranges
+ [ 0.000000] node 0: [mem 0x0000000080200000-0x000000027fffffff]
+ [ 0.000000] Initmem setup node 0 [mem 0x0000000080200000-0x000000027fffffff]
+ [ 0.000000] software IO TLB: mapped [mem 0xfbfff000-0xfffff000] (64MB)
+ [ 0.000000] CPU with hartid=0 is not available
+ [ 0.000000] CPU with hartid=0 is not available
+ [ 0.000000] elf_hwcap is 0x112d
+ [ 0.000000] percpu: Embedded 17 pages/cpu s31848 r8192 d29592 u69632
+ [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 2067975
+ [ 0.000000] Kernel command line:
+ [ 0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
+ [ 0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
+ [ 0.000000] Sorting __ex_table...
+ [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
+ [ 0.000000] Memory: 8179388K/8386560K available (6288K kernel code, 458K rwdata, 2135K rodata, 239K init, 311K bss, 207172K reserved, 0K cma-reserved)
+ [ 0.000000] Virtual kernel memory layout:
+ [ 0.000000] fixmap : 0xffffffcefee00000 - 0xffffffceff000000 (2048 kB)
+ [ 0.000000] pci io : 0xffffffceff000000 - 0xffffffcf00000000 ( 16 MB)
+ [ 0.000000] vmemmap : 0xffffffcf00000000 - 0xffffffcfffffffff (4095 MB)
+ [ 0.000000] vmalloc : 0xffffffd000000000 - 0xffffffdfffffffff (65535 MB)
+ [ 0.000000] lowmem : 0xffffffe000000000 - 0xffffffe1ffe00000 (8190 MB)
+ [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
+ [ 0.000000] rcu: Hierarchical RCU implementation.
+ [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
+ [ 0.000000] rcu: RCU debug extended QS entry/exit.
+ [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
+ [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
+ [ 0.000000] NR_IRQS: 0, nr_irqs: 0, preallocated irqs: 0
+ [ 0.000000] plic: mapped 53 interrupts with 4 handlers for 9 contexts.
+ [ 0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [1]
+ [ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 3526361616960 ns
+ [ 0.000007] sched_clock: 64 bits at 1000kHz, resolution 1000ns, wraps every 2199023255500ns
+ [ 0.000159] Console: colour dummy device 80x25
+ [ 0.001130] printk: console [tty0] enabled
+ [ 0.001193] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=4000)
+ [ 0.001259] pid_max: default: 32768 minimum: 301
+ [ 0.001798] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
+ [ 0.002191] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
+ [ 0.004308] rcu: Hierarchical SRCU implementation.
+ [ 0.004981] smp: Bringing up secondary CPUs ...
+ [ 1.024833] CPU1: failed to come online
+ [ 2.049612] CPU2: failed to come online
+ [ 3.074387] CPU3: failed to come online
+ [ 3.074453] smp: Brought up 1 node, 1 CPU
+ [ 3.075612] devtmpfs: initialized
+ [ 3.077517] random: get_random_u32 called from bucket_table_alloc.isra.0+0x4e/0x15e with crng_init=0
+ [ 3.077774] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
+ [ 3.077899] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
+ [ 3.078689] NET: Registered protocol family 16
+ [ 3.094523] vgaarb: loaded
+ [ 3.094914] SCSI subsystem initialized
+ [ 3.095364] usbcore: registered new interface driver usbfs
+ [ 3.095444] usbcore: registered new interface driver hub
+ [ 3.095533] usbcore: registered new device driver usb
+ [ 3.096290] clocksource: Switched to clocksource riscv_clocksource
+ [ 3.103494] NET: Registered protocol family 2
+ [ 3.104158] tcp_listen_portaddr_hash hash table entries: 4096 (order: 5, 163840 bytes, linear)
+ [ 3.104806] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear)
+ [ 3.106882] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes, linear)
+ [ 3.114045] TCP: Hash tables configured (established 65536 bind 65536)
+ [ 3.114589] UDP hash table entries: 4096 (order: 6, 393216 bytes, linear)
+ [ 3.115949] UDP-Lite hash table entries: 4096 (order: 6, 393216 bytes, linear)
+ [ 3.117578] NET: Registered protocol family 1
+ [ 3.118255] RPC: Registered named UNIX socket transport module.
+ [ 3.118295] RPC: Registered udp transport module.
+ [ 3.118328] RPC: Registered tcp transport module.
+ [ 3.118360] RPC: Registered tcp NFSv4.1 backchannel transport module.
+ [ 3.118397] PCI: CLS 0 bytes, default 64
+ [ 3.118621] Unpacking initramfs...
+ [ 3.475555] Freeing initrd memory: 4460K
+ [ 3.476511] workingset: timestamp_bits=62 max_order=21 bucket_order=0
+ [ 3.485899] NFS: Registering the id_resolver key type
+ [ 3.485961] Key type id_resolver registered
+ [ 3.485994] Key type id_legacy registered
+ [ 3.486037] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
+ [ 3.486236] 9p: Installing v9fs 9p2000 file system support
+ [ 3.486651] NET: Registered protocol family 38
+ [ 3.486729] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
+ [ 3.486788] io scheduler mq-deadline registered
+ [ 3.486822] io scheduler kyber registered
+ [ 3.528973] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
+ [ 3.530114] 10010000.serial: ttySIF0 at MMIO 0x10010000 (irq = 1, base_baud = 0) is a SiFive UART v0
+ [ 4.061558] printk: console [ttySIF0] enabled
+ [ 4.066211] 10011000.serial: ttySIF1 at MMIO 0x10011000 (irq = 10, base_baud = 0) is a SiFive UART v0
+ [ 4.075620] [drm] radeon kernel modesetting enabled.
+ [ 4.092998] loop: module loaded
+ [ 4.096007] sifive_spi 10040000.spi: mapped; irq=12, cs=1
+ [ 4.101380] sifive_spi 10050000.spi: mapped; irq=13, cs=1
+ [ 4.107129] libphy: Fixed MDIO Bus: probed
+ [ 4.111232] macb 10090000.ethernet: Registered clk switch 'sifive-gemgxl-mgmt'
+ [ 4.117841] macb 10090000.ethernet: GEM doesn't support hardware ptp.
+ [ 4.124654] libphy: MACB_mii_bus: probed
+ [ 4.133149] macb 10090000.ethernet eth0: Cadence GEM rev 0x10070109 at 0x10090000 irq 14 (86:5d:6f:58:d6:3d)
+ [ 4.142400] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
+ [ 4.148053] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
+ [ 4.154051] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
+ [ 4.160470] ehci-pci: EHCI PCI platform driver
+ [ 4.164930] ehci-platform: EHCI generic platform driver
+ [ 4.170185] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
+ [ 4.176284] ohci-pci: OHCI PCI platform driver
+ [ 4.180736] ohci-platform: OHCI generic platform driver
+ [ 4.186226] usbcore: registered new interface driver uas
+ [ 4.191257] usbcore: registered new interface driver usb-storage
+ [ 4.197392] mousedev: PS/2 mouse device common for all mice
+ [ 4.228311] mmc_spi spi1.0: SD/MMC host mmc0, no DMA, no WP, no poweroff, cd polling
+ [ 4.235528] usbcore: registered new interface driver usbhid
+ [ 4.240870] usbhid: USB HID core driver
+ [ 4.245515] NET: Registered protocol family 10
+ [ 4.250603] Segment Routing with IPv6
+ [ 4.253602] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
+ [ 4.259978] NET: Registered protocol family 17
+ [ 4.264098] 9pnet: Installing 9P2000 support
+ [ 4.268159] Key type dns_resolver registered
+ [ 4.279265] Freeing unused kernel memory: 236K
+ [ 4.282989] This architecture does not have kernel memory protection.
+ [ 4.289390] Run /init as init process
+ Starting syslogd: OK
+ Starting klogd: OK
+ Starting mdev...
+ /etc/init.d/S10mdev: line 9: can't create /proc/sys/kernel/hotplug: nonexistent directory
+ [ 4.354461] mmc0: host does not support reading read-only switch, assuming write-enable
+ [ 4.361778] mmc0: new SDHC card on SPI
+ [ 4.381184] mmcblk0: mmc0:0000 SC16G 14.8 GiB
+ [ 4.424975] mmcblk0: p1 p2 p3
+ modprobe: can't change directory to '/lib/modules': No such file or directory
+ Initializing random number generator... [ 5.041362] random: dd: uninitialized urandom read (512 bytes read)
+ done.
+ Starting network: [ 5.240580] macb 10090000.ethernet eth0: PHY [10090000.ethernet-ffffffff:00] driver [Microsemi VSC8541 SyncE] (irq=POLL)
+ [ 5.250752] macb 10090000.ethernet eth0: configuring for phy/gmii link mode
+ udhcpc: started, v1.29.3
+ udhcpc: sending discover
+ [ 7.301682] macb 10090000.ethernet eth0: Link is Up - 100Mbps/Full - flow control tx
+ [ 7.308726] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
+ udhcpc: sending discover
+ udhcpc: sending discover
+ udhcpc: no lease, failing
+ FAIL
+ Starting dropbear sshd: [ 14.309152] random: dropbear: uninitialized urandom read (32 bytes read)
+ OK
+
+ Welcome to Buildroot
+ buildroot login: root
+ Password:
+ #
--
2.17.1
^ permalink raw reply related [flat|nested] 118+ messages in thread
* [PATCH v7 04/22] lib: Makefile: build crc7.c when CONFIG_MMC_SPI
2020-05-02 10:06 ` [PATCH v7 04/22] lib: Makefile: build crc7.c when CONFIG_MMC_SPI Pragnesh Patel
@ 2020-05-02 10:29 ` Heinrich Schuchardt
2020-05-02 11:47 ` Bin Meng
2020-05-02 12:28 ` Bin Meng
1 sibling, 1 reply; 118+ messages in thread
From: Heinrich Schuchardt @ 2020-05-02 10:29 UTC (permalink / raw)
To: u-boot
On 5/2/20 12:06 PM, Pragnesh Patel wrote:
> When build U-Boot SPL, meet an issue of undefined reference to
> 'crc7' for drivers/mmc/mmc_spi.c, so let's compile crc7.c when
> CONFIG_MMC_SPI selected.
>
> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
> ---
> common/spl/Kconfig | 6 ++++++
> drivers/mmc/Kconfig | 1 +
> lib/Makefile | 1 +
> 3 files changed, 8 insertions(+)
>
> diff --git a/common/spl/Kconfig b/common/spl/Kconfig
> index ef5bf66696..d1f0e6bc4c 100644
> --- a/common/spl/Kconfig
> +++ b/common/spl/Kconfig
> @@ -401,6 +401,12 @@ config SPL_CRC32_SUPPORT
> for detected accidental image corruption. For secure applications you
> should consider SHA1 or SHA256.
>
> +config SPL_CRC7_SUPPORT
> + bool "Support CRC7"
> + help
> + Enable CRC7 hashing for drivers which are using in SPL.
> + This is a 32-bit checksum value that can be used to verify images.
> +
> config SPL_MD5_SUPPORT
> bool "Support MD5"
> depends on SPL_FIT
> diff --git a/drivers/mmc/Kconfig b/drivers/mmc/Kconfig
> index 8f0df568b9..139599072a 100644
> --- a/drivers/mmc/Kconfig
> +++ b/drivers/mmc/Kconfig
> @@ -49,6 +49,7 @@ if MMC
> config MMC_SPI
> bool "Support for SPI-based MMC controller"
> depends on DM_MMC && DM_SPI
> + select SPL_CRC7_SUPPORT if SPL
> help
> This selects SPI-based MMC controllers.
> If you have an MMC controller on a SPI bus, say Y here.
> diff --git a/lib/Makefile b/lib/Makefile
> index c6f862b0c2..fcd934857f 100644
> --- a/lib/Makefile
> +++ b/lib/Makefile
> @@ -80,6 +80,7 @@ endif
>
> ifdef CONFIG_SPL_BUILD
> obj-$(CONFIG_SPL_YMODEM_SUPPORT) += crc16.o
> +obj-$(CONFIG_SPL_CRC7_SUPPORT) += crc7.o
crc7.o is not needed in main U-Boot if MMC_SPI is not selected.
So instead of adding a new configuration variable simply correct the
existing line in lib/Makefile
-obj-y += crc7.o
+obj-$(CONFIG_MMC_SPI) += crc7.o
and move that line inside lib/Makefile so that is does not depend on
CONFIG_SPL_BUILD.
Best regards
Heinrich
> obj-$(CONFIG_$(SPL_TPL_)HASH_SUPPORT) += crc16.o
> obj-y += net_utils.o
> endif
>
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 04/22] lib: Makefile: build crc7.c when CONFIG_MMC_SPI
2020-05-02 10:29 ` Heinrich Schuchardt
@ 2020-05-02 11:47 ` Bin Meng
2020-05-02 12:58 ` Heinrich Schuchardt
0 siblings, 1 reply; 118+ messages in thread
From: Bin Meng @ 2020-05-02 11:47 UTC (permalink / raw)
To: u-boot
Hi Heinrich,
On Sat, May 2, 2020 at 6:30 PM Heinrich Schuchardt <xypron.glpk@gmx.de> wrote:
>
> On 5/2/20 12:06 PM, Pragnesh Patel wrote:
> > When build U-Boot SPL, meet an issue of undefined reference to
> > 'crc7' for drivers/mmc/mmc_spi.c, so let's compile crc7.c when
> > CONFIG_MMC_SPI selected.
> >
> > Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
> > Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
> > Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
> > ---
> > common/spl/Kconfig | 6 ++++++
> > drivers/mmc/Kconfig | 1 +
> > lib/Makefile | 1 +
> > 3 files changed, 8 insertions(+)
> >
> > diff --git a/common/spl/Kconfig b/common/spl/Kconfig
> > index ef5bf66696..d1f0e6bc4c 100644
> > --- a/common/spl/Kconfig
> > +++ b/common/spl/Kconfig
> > @@ -401,6 +401,12 @@ config SPL_CRC32_SUPPORT
> > for detected accidental image corruption. For secure applications you
> > should consider SHA1 or SHA256.
> >
> > +config SPL_CRC7_SUPPORT
> > + bool "Support CRC7"
> > + help
> > + Enable CRC7 hashing for drivers which are using in SPL.
> > + This is a 32-bit checksum value that can be used to verify images.
> > +
> > config SPL_MD5_SUPPORT
> > bool "Support MD5"
> > depends on SPL_FIT
> > diff --git a/drivers/mmc/Kconfig b/drivers/mmc/Kconfig
> > index 8f0df568b9..139599072a 100644
> > --- a/drivers/mmc/Kconfig
> > +++ b/drivers/mmc/Kconfig
> > @@ -49,6 +49,7 @@ if MMC
> > config MMC_SPI
> > bool "Support for SPI-based MMC controller"
> > depends on DM_MMC && DM_SPI
> > + select SPL_CRC7_SUPPORT if SPL
> > help
> > This selects SPI-based MMC controllers.
> > If you have an MMC controller on a SPI bus, say Y here.
> > diff --git a/lib/Makefile b/lib/Makefile
> > index c6f862b0c2..fcd934857f 100644
> > --- a/lib/Makefile
> > +++ b/lib/Makefile
> > @@ -80,6 +80,7 @@ endif
> >
> > ifdef CONFIG_SPL_BUILD
> > obj-$(CONFIG_SPL_YMODEM_SUPPORT) += crc16.o
> > +obj-$(CONFIG_SPL_CRC7_SUPPORT) += crc7.o
>
> crc7.o is not needed in main U-Boot if MMC_SPI is not selected.
>
> So instead of adding a new configuration variable simply correct the
> existing line in lib/Makefile
>
> -obj-y += crc7.o
> +obj-$(CONFIG_MMC_SPI) += crc7.o
This looks incorrect to me. CRC7 can be useful for other drivers too.
It should not depend on CONFIG_MMC_SPI.
>
> and move that line inside lib/Makefile so that is does not depend on
> CONFIG_SPL_BUILD.
>
Regards,
Bin
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 10/22] clk: sifive: fu540-prci: ddr and ethernet clock initialization in SPL
2020-05-02 10:06 ` [PATCH v7 10/22] clk: sifive: fu540-prci: ddr and ethernet clock initialization in SPL Pragnesh Patel
@ 2020-05-02 12:28 ` Bin Meng
2020-05-02 14:49 ` Pragnesh Patel
2020-05-02 16:14 ` Jagan Teki
1 sibling, 1 reply; 118+ messages in thread
From: Bin Meng @ 2020-05-02 12:28 UTC (permalink / raw)
To: u-boot
Hi Pragnesh,
On Sat, May 2, 2020 at 6:08 PM Pragnesh Patel <pragnesh.patel@sifive.com> wrote:
>
> Add ddr clock release reset and ehternet clock initialization for
> SPL
>
> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
> ---
> drivers/clk/sifive/fu540-prci.c | 87 ++++++++++++++++++++++++++++++---
> 1 file changed, 81 insertions(+), 6 deletions(-)
>
> diff --git a/drivers/clk/sifive/fu540-prci.c b/drivers/clk/sifive/fu540-prci.c
> index bf06c3a3bb..1c89bdf242 100644
> --- a/drivers/clk/sifive/fu540-prci.c
> +++ b/drivers/clk/sifive/fu540-prci.c
> @@ -41,6 +41,8 @@
> #include <linux/clk/analogbits-wrpll-cln28hpc.h>
> #include <dt-bindings/clock/sifive-fu540-prci.h>
>
> +#define MHz 1000000
> +
> /*
> * EXPECTED_CLK_PARENT_COUNT: how many parent clocks this driver expects:
> * hfclk and rtcclk
> @@ -152,6 +154,12 @@
> #define PRCI_CLKMUXSTATUSREG_TLCLKSEL_STATUS_MASK \
> (0x1 << PRCI_CLKMUXSTATUSREG_TLCLKSEL_STATUS_SHIFT)
>
> +/* PROCMONCFG */
> +#define PRCI_PROCMONCFG_OFFSET 0xF0
> +#define PRCI_PROCMONCFG_CORE_CLOCK_SHIFT 24
> +#define PRCI_PROCMONCFG_CORE_CLOCK_MASK \
> + (0x1 << PRCI_PROCMONCFG_CORE_CLOCK_SHIFT)
> +
> /*
> * Private structures
> */
> @@ -176,6 +184,7 @@ struct __prci_data {
> * @disable_bypass: fn ptr to code to not bypass the WRPLL (or NULL)
> * @cfg0_offs: WRPLL CFG0 register offset (in bytes) from the PRCI base address
> * @cfg1_offs: WRPLL CFG1 register offset (in bytes) from the PRCI base address
> + * @release_reset: fn ptr to code to release clock reset
> *
> * @enable_bypass and @disable_bypass are used for WRPLL instances
> * that contain a separate external glitchless clock mux downstream
> @@ -187,6 +196,9 @@ struct __prci_wrpll_data {
> void (*disable_bypass)(struct __prci_data *pd);
> u8 cfg0_offs;
> u8 cfg1_offs;
> +#ifdef CONFIG_SPL_BUILD
> + void (*release_reset)(struct __prci_data *pd);
> +#endif
> };
>
> struct __prci_clock;
> @@ -476,6 +488,11 @@ static int sifive_fu540_prci_clock_enable(struct __prci_clock *pc, bool enable)
>
> if (enable) {
> __prci_wrpll_write_cfg1(pd, pwd, PRCI_COREPLLCFG1_CKE_MASK);
> +
> +#ifdef CONFIG_SPL_BUILD
> + if (pwd->release_reset)
> + pwd->release_reset(pd);
> +#endif
> } else {
> u32 r;
>
> @@ -495,11 +512,6 @@ static const struct __prci_clock_ops sifive_fu540_prci_wrpll_clk_ops = {
> .enable_clk = sifive_fu540_prci_clock_enable,
> };
>
> -static const struct __prci_clock_ops sifive_fu540_prci_wrpll_ro_clk_ops = {
> - .recalc_rate = sifive_fu540_prci_wrpll_recalc_rate,
> - .enable_clk = sifive_fu540_prci_clock_enable,
> -};
> -
> /* TLCLKSEL clock integration */
>
> static unsigned long sifive_fu540_prci_tlclksel_recalc_rate(
> @@ -521,6 +533,39 @@ static const struct __prci_clock_ops sifive_fu540_prci_tlclksel_clk_ops = {
> .recalc_rate = sifive_fu540_prci_tlclksel_recalc_rate,
> };
>
> +#ifdef CONFIG_SPL_BUILD
> +/**
> + * __prci_ddr_release_reset() - Release DDR reset
> + * @pd: struct __prci_data * for the PRCI containing the DDRCLK mux reg
> + *
> + */
> +static void __prci_ddr_release_reset(struct __prci_data *pd)
> +{
> + u32 v;
> +
> + v = __prci_readl(pd, PRCI_DEVICESRESETREG_OFFSET);
> + v |= PRCI_DEVICESRESETREG_DDR_CTRL_RST_N_MASK;
> + __prci_writel(v, PRCI_DEVICESRESETREG_OFFSET, pd);
> +
> + // HACK to get the '1 full controller clock cycle'.
nits: should use /* */
> + asm volatile ("fence");
> + v = __prci_readl(pd, PRCI_DEVICESRESETREG_OFFSET);
> + v |= (PRCI_DEVICESRESETREG_DDR_AXI_RST_N_MASK |
> + PRCI_DEVICESRESETREG_DDR_AHB_RST_N_MASK |
> + PRCI_DEVICESRESETREG_DDR_PHY_RST_N_MASK);
> + __prci_writel(v, PRCI_DEVICESRESETREG_OFFSET, pd);
> + // HACK to get the '1 full controller clock cycle'.
the same here
> + asm volatile ("fence");
> +
> + /* These take like 16 cycles to actually propagate. We can't go sending
nits: wrong multi-line comment format
> + * stuff before they come out of reset. So wait. (TODO: Add a register
> + * to read the current reset states, or DDR Control device?)
Is there no register to reflect the reset states?
> + */
> + for (int i = 0; i < 256; i++)
> + asm volatile ("nop");
> +}
> +#endif
> +
> /*
> * PRCI integration data for each WRPLL instance
> */
> @@ -535,6 +580,9 @@ static struct __prci_wrpll_data __prci_corepll_data = {
> static struct __prci_wrpll_data __prci_ddrpll_data = {
> .cfg0_offs = PRCI_DDRPLLCFG0_OFFSET,
> .cfg1_offs = PRCI_DDRPLLCFG1_OFFSET,
> +#ifdef CONFIG_SPL_BUILD
> + .release_reset = __prci_ddr_release_reset,
> +#endif
> };
>
> static struct __prci_wrpll_data __prci_gemgxlpll_data = {
> @@ -556,7 +604,7 @@ static struct __prci_clock __prci_init_clocks[] = {
> [PRCI_CLK_DDRPLL] = {
> .name = "ddrpll",
> .parent_name = "hfclk",
> - .ops = &sifive_fu540_prci_wrpll_ro_clk_ops,
> + .ops = &sifive_fu540_prci_wrpll_clk_ops,
> .pwd = &__prci_ddrpll_data,
> },
> [PRCI_CLK_GEMGXLPLL] = {
> @@ -662,6 +710,29 @@ static int sifive_fu540_prci_disable(struct clk *clk)
> return ret;
> }
>
> +#ifdef CONFIG_SPL_BUILD
> +static void ethernet_init(struct udevice *dev)
> +{
> + u32 v;
> + struct clk clock;
> + struct __prci_data *pd = dev_get_priv(dev);
> +
> + /* GEMGXL init */
> + clock.id = PRCI_CLK_GEMGXLPLL;
> + sifive_fu540_prci_set_rate(&clock, 125UL * MHz);
> + sifive_fu540_prci_clock_enable(&__prci_init_clocks[clock.id], 1);
> +
> + /* Release GEMGXL reset */
> + v = __prci_readl(pd, PRCI_DEVICESRESETREG_OFFSET);
> + v |= PRCI_DEVICESRESETREG_GEMGXL_RST_N_MASK;
> + __prci_writel(v, PRCI_DEVICESRESETREG_OFFSET, pd);
> +
> + /* Procmon => core clock */
> + __prci_writel(PRCI_PROCMONCFG_CORE_CLOCK_MASK, PRCI_PROCMONCFG_OFFSET,
> + pd);
> +}
> +#endif
> +
> static int sifive_fu540_prci_probe(struct udevice *dev)
> {
> int i, err;
> @@ -687,6 +758,10 @@ static int sifive_fu540_prci_probe(struct udevice *dev)
> __prci_wrpll_read_cfg0(pd, pc->pwd);
> }
>
> +#ifdef CONFIG_SPL_BUILD
> + ethernet_init(dev);
> +#endif
> +
> return 0;
> }
Regards,
Bin
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 01/22] misc: add driver for the SiFive otp controller
2020-05-02 10:06 ` [PATCH v7 01/22] misc: add driver for the SiFive otp controller Pragnesh Patel
@ 2020-05-02 12:28 ` Bin Meng
2020-05-02 15:37 ` Jagan Teki
1 sibling, 0 replies; 118+ messages in thread
From: Bin Meng @ 2020-05-02 12:28 UTC (permalink / raw)
To: u-boot
On Sat, May 2, 2020 at 6:07 PM Pragnesh Patel <pragnesh.patel@sifive.com> wrote:
>
> Added a misc driver to handle OTP memory in SiFive SoCs.
>
> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
> ---
> drivers/misc/Kconfig | 7 +
> drivers/misc/Makefile | 1 +
> drivers/misc/sifive-otp.c | 273 ++++++++++++++++++++++++++++++++++++++
> 3 files changed, 281 insertions(+)
> create mode 100644 drivers/misc/sifive-otp.c
>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 02/22] riscv: sifive: fu540: Use OTP DM driver for serial environment variable
2020-05-02 10:06 ` [PATCH v7 02/22] riscv: sifive: fu540: Use OTP DM driver for serial environment variable Pragnesh Patel
@ 2020-05-02 12:28 ` Bin Meng
0 siblings, 0 replies; 118+ messages in thread
From: Bin Meng @ 2020-05-02 12:28 UTC (permalink / raw)
To: u-boot
On Sat, May 2, 2020 at 6:07 PM Pragnesh Patel <pragnesh.patel@sifive.com> wrote:
>
> Use the OTP DM driver to set the serial environment variable.
>
> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
> ---
> arch/riscv/dts/fu540-c000-u-boot.dtsi | 14 +++
> .../dts/hifive-unleashed-a00-u-boot.dtsi | 2 +
> board/sifive/fu540/Kconfig | 2 +
> board/sifive/fu540/fu540.c | 111 ++++++------------
> 4 files changed, 57 insertions(+), 72 deletions(-)
> create mode 100644 arch/riscv/dts/fu540-c000-u-boot.dtsi
>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 03/22] riscv: Add _image_binary_end for SPL
2020-05-02 10:06 ` [PATCH v7 03/22] riscv: Add _image_binary_end for SPL Pragnesh Patel
@ 2020-05-02 12:28 ` Bin Meng
0 siblings, 0 replies; 118+ messages in thread
From: Bin Meng @ 2020-05-02 12:28 UTC (permalink / raw)
To: u-boot
On Sat, May 2, 2020 at 6:07 PM Pragnesh Patel <pragnesh.patel@sifive.com> wrote:
>
> For SPL_SEPARATE_BSS, Device tree will be put at _image_binary_end
>
> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
> Reviewed-by: Anup Patel <anup.patel@wdc.com>
> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
> ---
> arch/riscv/cpu/u-boot-spl.lds | 1 +
> 1 file changed, 1 insertion(+)
>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 04/22] lib: Makefile: build crc7.c when CONFIG_MMC_SPI
2020-05-02 10:06 ` [PATCH v7 04/22] lib: Makefile: build crc7.c when CONFIG_MMC_SPI Pragnesh Patel
2020-05-02 10:29 ` Heinrich Schuchardt
@ 2020-05-02 12:28 ` Bin Meng
1 sibling, 0 replies; 118+ messages in thread
From: Bin Meng @ 2020-05-02 12:28 UTC (permalink / raw)
To: u-boot
On Sat, May 2, 2020 at 6:07 PM Pragnesh Patel <pragnesh.patel@sifive.com> wrote:
>
> When build U-Boot SPL, meet an issue of undefined reference to
> 'crc7' for drivers/mmc/mmc_spi.c, so let's compile crc7.c when
> CONFIG_MMC_SPI selected.
>
> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
> ---
> common/spl/Kconfig | 6 ++++++
> drivers/mmc/Kconfig | 1 +
> lib/Makefile | 1 +
> 3 files changed, 8 insertions(+)
>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 06/22] sifive: fu540: add ddr driver
2020-05-02 10:06 ` [PATCH v7 06/22] sifive: fu540: add ddr driver Pragnesh Patel
@ 2020-05-02 12:28 ` Bin Meng
2020-05-02 15:59 ` Jagan Teki
1 sibling, 0 replies; 118+ messages in thread
From: Bin Meng @ 2020-05-02 12:28 UTC (permalink / raw)
To: u-boot
On Sat, May 2, 2020 at 6:07 PM Pragnesh Patel <pragnesh.patel@sifive.com> wrote:
>
> Add driver for fu540 to support ddr initialization in SPL.
> This driver is based on FSBL
> (https://github.com/sifive/freedom-u540-c000-bootloader.git)
>
> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
> ---
> board/sifive/fu540/Kconfig | 2 +
> drivers/ram/Kconfig | 1 +
> drivers/ram/Makefile | 2 +
> drivers/ram/sifive/Kconfig | 13 +
> drivers/ram/sifive/Makefile | 6 +
> drivers/ram/sifive/sdram_fu540.c | 416 +++++++++++++++++++++++++++++++
> 6 files changed, 440 insertions(+)
> create mode 100644 drivers/ram/sifive/Kconfig
> create mode 100644 drivers/ram/sifive/Makefile
> create mode 100644 drivers/ram/sifive/sdram_fu540.c
>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 07/22] sifive: dts: fu540: Add DDR controller and phy register settings
2020-05-02 10:06 ` [PATCH v7 07/22] sifive: dts: fu540: Add DDR controller and phy register settings Pragnesh Patel
@ 2020-05-02 12:28 ` Bin Meng
2020-05-02 14:41 ` Pragnesh Patel
0 siblings, 1 reply; 118+ messages in thread
From: Bin Meng @ 2020-05-02 12:28 UTC (permalink / raw)
To: u-boot
On Sat, May 2, 2020 at 6:08 PM Pragnesh Patel <pragnesh.patel@sifive.com> wrote:
>
> Add DDR controller and phy register settings, taken from fsbl
> (https://github.com/sifive/freedom-u540-c000-bootloader.git)
>
> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
> ---
> ...fu540-hifive-unleashed-a00-sdram-ddr4.dtsi | 1489 +++++++++++++++++
> 1 file changed, 1489 insertions(+)
> create mode 100644 arch/riscv/dts/fu540-hifive-unleashed-a00-sdram-ddr4.dtsi
>
> diff --git a/arch/riscv/dts/fu540-hifive-unleashed-a00-sdram-ddr4.dtsi b/arch/riscv/dts/fu540-hifive-unleashed-a00-sdram-ddr4.dtsi
> new file mode 100644
> index 0000000000..370c53800d
> --- /dev/null
> +++ b/arch/riscv/dts/fu540-hifive-unleashed-a00-sdram-ddr4.dtsi
> @@ -0,0 +1,1489 @@
> +// SPDX-License-Identifier: GPL-2.0+
Should this file be dual-licensed?
> +/*
> + * (C) Copyright 2020 SiFive, Inc
> + */
> +
Tested-by: Bin Meng <bmeng.cn@gmail.com>
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 08/22] riscv: sifive: dts: fu540: add U-Boot dmc node
2020-05-02 10:06 ` [PATCH v7 08/22] riscv: sifive: dts: fu540: add U-Boot dmc node Pragnesh Patel
@ 2020-05-02 12:29 ` Bin Meng
0 siblings, 0 replies; 118+ messages in thread
From: Bin Meng @ 2020-05-02 12:29 UTC (permalink / raw)
To: u-boot
On Sat, May 2, 2020 at 6:08 PM Pragnesh Patel <pragnesh.patel@sifive.com> wrote:
>
> Add dmc node to enable sdram driver. dmc is used to
> initialize the memory controller.
>
> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
> ---
> arch/riscv/dts/fu540-c000-u-boot.dtsi | 9 +++++++++
> 1 file changed, 9 insertions(+)
>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 09/22] clk: sifive: fu540-prci: Add clock enable and disable ops
2020-05-02 10:06 ` [PATCH v7 09/22] clk: sifive: fu540-prci: Add clock enable and disable ops Pragnesh Patel
@ 2020-05-02 12:29 ` Bin Meng
0 siblings, 0 replies; 118+ messages in thread
From: Bin Meng @ 2020-05-02 12:29 UTC (permalink / raw)
To: u-boot
On Sat, May 2, 2020 at 6:08 PM Pragnesh Patel <pragnesh.patel@sifive.com> wrote:
>
> Added clock enable and disable functions in prci ops
>
> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
> ---
> drivers/clk/sifive/fu540-prci.c | 108 ++++++++++++++++++++++++++++----
> 1 file changed, 96 insertions(+), 12 deletions(-)
>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 13/22] riscv: cpu: fu540: Add support for cpu fu540
2020-05-02 10:06 ` [PATCH v7 13/22] riscv: cpu: fu540: Add support for cpu fu540 Pragnesh Patel
@ 2020-05-02 12:32 ` Bin Meng
2020-05-02 14:38 ` Pragnesh Patel
2020-05-02 16:34 ` Jagan Teki
1 sibling, 1 reply; 118+ messages in thread
From: Bin Meng @ 2020-05-02 12:32 UTC (permalink / raw)
To: u-boot
Hi Pragnesh,
On Sat, May 2, 2020 at 6:08 PM Pragnesh Patel <pragnesh.patel@sifive.com> wrote:
>
> Add SiFive fu540 cpu to support RISC-V arch
>
> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
> ---
> arch/riscv/Kconfig | 1 +
> arch/riscv/cpu/fu540/Kconfig | 15 ++++++++++++++
> arch/riscv/cpu/fu540/Makefile | 7 +++++++
> arch/riscv/cpu/fu540/cpu.c | 22 ++++++++++++++++++++
> arch/riscv/cpu/fu540/dram.c | 38 +++++++++++++++++++++++++++++++++++
> 5 files changed, 83 insertions(+)
> create mode 100644 arch/riscv/cpu/fu540/Kconfig
> create mode 100644 arch/riscv/cpu/fu540/Makefile
> create mode 100644 arch/riscv/cpu/fu540/cpu.c
> create mode 100644 arch/riscv/cpu/fu540/dram.c
>
> diff --git a/arch/riscv/Kconfig b/arch/riscv/Kconfig
> index fb5fe5afff..3044609971 100644
> --- a/arch/riscv/Kconfig
> +++ b/arch/riscv/Kconfig
> @@ -57,6 +57,7 @@ source "board/sifive/fu540/Kconfig"
> # platform-specific options below
> source "arch/riscv/cpu/ax25/Kconfig"
> source "arch/riscv/cpu/generic/Kconfig"
> +source "arch/riscv/cpu/fu540/Kconfig"
>
> # architecture-specific options below
>
> diff --git a/arch/riscv/cpu/fu540/Kconfig b/arch/riscv/cpu/fu540/Kconfig
> new file mode 100644
> index 0000000000..b2cb155d6d
> --- /dev/null
> +++ b/arch/riscv/cpu/fu540/Kconfig
> @@ -0,0 +1,15 @@
> +# SPDX-License-Identifier: GPL-2.0+
> +#
> +# Copyright (C) 2018, Bin Meng <bmeng.cn@gmail.com>
> +
> +config GENERIC_RISCV
This should be SIFIVE_FU540
> + bool
> + select ARCH_EARLY_INIT_R
> + imply CPU
> + imply CPU_RISCV
> + imply RISCV_TIMER
> + imply SIFIVE_CLINT if (RISCV_MMODE || SPL_RISCV_MMODE)
> + imply CMD_CPU
> + imply SPL_CPU_SUPPORT
> + imply SPL_OPENSBI
> + imply SPL_LOAD_FIT
> diff --git a/arch/riscv/cpu/fu540/Makefile b/arch/riscv/cpu/fu540/Makefile
> new file mode 100644
> index 0000000000..44700d998c
> --- /dev/null
> +++ b/arch/riscv/cpu/fu540/Makefile
> @@ -0,0 +1,7 @@
> +# SPDX-License-Identifier: GPL-2.0+
> +#
> +# Copyright (C) 2020 SiFive, Inc
> +# Pragnesh Patel <pragnesh.patel@sifive.com>
> +
> +obj-y += dram.o
> +obj-y += cpu.o
> diff --git a/arch/riscv/cpu/fu540/cpu.c b/arch/riscv/cpu/fu540/cpu.c
> new file mode 100644
> index 0000000000..13a69ef0cc
> --- /dev/null
> +++ b/arch/riscv/cpu/fu540/cpu.c
> @@ -0,0 +1,22 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (C) 2018, Bin Meng <bmeng.cn@gmail.com>
> + */
> +
> +#include <common.h>
> +#include <irq_func.h>
> +
> +/*
> + * cleanup_before_linux() is called just before we call linux
> + * it prepares the processor for linux
> + *
> + * we disable interrupt and caches.
> + */
> +int cleanup_before_linux(void)
> +{
> + disable_interrupts();
> +
> + cache_flush();
> +
> + return 0;
> +}
> diff --git a/arch/riscv/cpu/fu540/dram.c b/arch/riscv/cpu/fu540/dram.c
> new file mode 100644
> index 0000000000..1dc77efeca
> --- /dev/null
> +++ b/arch/riscv/cpu/fu540/dram.c
> @@ -0,0 +1,38 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (C) 2018, Bin Meng <bmeng.cn@gmail.com>
> + */
> +
> +#include <common.h>
> +#include <fdtdec.h>
> +#include <init.h>
> +#include <linux/sizes.h>
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +int dram_init(void)
> +{
> + return fdtdec_setup_mem_size_base();
> +}
> +
> +int dram_init_banksize(void)
> +{
> + return fdtdec_setup_memory_banksize();
> +}
> +
> +ulong board_get_usable_ram_top(ulong total_size)
> +{
> +#ifdef CONFIG_64BIT
> + /*
> + * Ensure that we run from first 4GB so that all
> + * addresses used by U-Boot are 32bit addresses.
> + *
> + * This in-turn ensures that 32bit DMA capable
> + * devices work fine because DMA mapping APIs will
> + * provide 32bit DMA addresses only.
> + */
> + if (gd->ram_top > SZ_4G)
> + return SZ_4G;
> +#endif
> + return gd->ram_top;
> +}
Other than that,
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Regards,
Bin
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 14/22] riscv: Add place-holder for driver compilation
2020-05-02 10:06 ` [PATCH v7 14/22] riscv: Add place-holder for driver compilation Pragnesh Patel
@ 2020-05-02 12:43 ` Bin Meng
2020-05-02 16:27 ` Jagan Teki
1 sibling, 0 replies; 118+ messages in thread
From: Bin Meng @ 2020-05-02 12:43 UTC (permalink / raw)
To: u-boot
On Sat, May 2, 2020 at 6:08 PM Pragnesh Patel <pragnesh.patel@sifive.com> wrote:
>
> Add place-holder for RISC-V fu540 CPU
>
> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
> ---
> arch/riscv/include/asm/arch-fu540/clk.h | 14 +++++++++
> arch/riscv/include/asm/arch-fu540/gpio.h | 38 ++++++++++++++++++++++++
> 2 files changed, 52 insertions(+)
> create mode 100644 arch/riscv/include/asm/arch-fu540/clk.h
> create mode 100644 arch/riscv/include/asm/arch-fu540/gpio.h
>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 15/22] riscv: sifive: dts: fu540: Add clock for cpus node
2020-05-02 10:06 ` [PATCH v7 15/22] riscv: sifive: dts: fu540: Add clock for cpus node Pragnesh Patel
@ 2020-05-02 12:43 ` Bin Meng
2020-05-02 16:50 ` Jagan Teki
1 sibling, 0 replies; 118+ messages in thread
From: Bin Meng @ 2020-05-02 12:43 UTC (permalink / raw)
To: u-boot
On Sat, May 2, 2020 at 6:08 PM Pragnesh Patel <pragnesh.patel@sifive.com> wrote:
>
> Add clock-frequency and clocks in cpus node, so that
> clock will be enabled by cpu driver.
>
> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
> ---
> arch/riscv/dts/fu540-c000-u-boot.dtsi | 10 ++++++++++
> 1 file changed, 10 insertions(+)
>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 16/22] riscv: Enable cpu clock if it is present
2020-05-02 10:06 ` [PATCH v7 16/22] riscv: Enable cpu clock if it is present Pragnesh Patel
@ 2020-05-02 12:55 ` Bin Meng
2020-05-02 18:15 ` Sean Anderson
1 sibling, 0 replies; 118+ messages in thread
From: Bin Meng @ 2020-05-02 12:55 UTC (permalink / raw)
To: u-boot
On Sat, May 2, 2020 at 6:08 PM Pragnesh Patel <pragnesh.patel@sifive.com> wrote:
>
> The cpu clock is probably already enabled if we are executing code (though
> we could be executing from a different core). This patch prevents the cpu
> clock or its parents from being disabled.
>
> Signed-off-by: Sean Anderson <seanga2@gmail.com>
> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
> ---
> drivers/cpu/riscv_cpu.c | 33 +++++++++++++++++++++++++++++++++
> 1 file changed, 33 insertions(+)
>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 17/22] riscv: sifive: fu540: add SPL configuration
2020-05-02 10:06 ` [PATCH v7 17/22] riscv: sifive: fu540: add SPL configuration Pragnesh Patel
@ 2020-05-02 12:55 ` Bin Meng
0 siblings, 0 replies; 118+ messages in thread
From: Bin Meng @ 2020-05-02 12:55 UTC (permalink / raw)
To: u-boot
On Sat, May 2, 2020 at 6:08 PM Pragnesh Patel <pragnesh.patel@sifive.com> wrote:
>
> Add a support for SPL which will boot from L2 LIM (0x0800_0000) and
> then SPL will boot U-Boot FIT image (OpenSBI FW_DYNAMIC + u-boot.bin)
> from MMC boot devices.
>
> SPL related code is leveraged from FSBL
> (https://github.com/sifive/freedom-u540-c000-bootloader.git)
>
> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
> ---
> arch/riscv/cpu/fu540/Makefile | 4 ++
> arch/riscv/cpu/fu540/spl.c | 23 ++++++
> .../dts/hifive-unleashed-a00-u-boot.dtsi | 1 +
> arch/riscv/include/asm/arch-fu540/spl.h | 14 ++++
> board/sifive/fu540/Kconfig | 10 ++-
> board/sifive/fu540/Makefile | 4 ++
> board/sifive/fu540/fu540.c | 24 +++++++
> board/sifive/fu540/spl.c | 72 +++++++++++++++++++
> include/configs/sifive-fu540.h | 18 +++++
> 9 files changed, 169 insertions(+), 1 deletion(-)
> create mode 100644 arch/riscv/cpu/fu540/spl.c
> create mode 100644 arch/riscv/include/asm/arch-fu540/spl.h
> create mode 100644 board/sifive/fu540/spl.c
>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 18/22] configs: fu540: Add config options for U-Boot SPL
2020-05-02 10:06 ` [PATCH v7 18/22] configs: fu540: Add config options for U-Boot SPL Pragnesh Patel
@ 2020-05-02 12:55 ` Bin Meng
2020-05-02 14:37 ` Pragnesh Patel
2020-05-02 17:04 ` Jagan Teki
2020-05-02 16:51 ` Jagan Teki
2020-05-02 17:15 ` Jagan Teki
2 siblings, 2 replies; 118+ messages in thread
From: Bin Meng @ 2020-05-02 12:55 UTC (permalink / raw)
To: u-boot
Hi Pragnesh,
On Sat, May 2, 2020 at 6:08 PM Pragnesh Patel <pragnesh.patel@sifive.com> wrote:
>
> With sifive_fu540_defconfig:
>
> User can use FSBL or u-boot-spl.bin anyone at a time.
>
> For FSBL,
> fsbl->fw_payload.bin (opensbi + U-Boot)
>
> For u-boot-spl.bin,
> u-boot-spl.bin->FIT image (opensbi + U-Boot + dtb)
>
> U-Boot SPL will be loaded by ZSBL from SD card (replace fsbl.bin with
> u-boot-spl.bin) and runs in L2 LIM in machine mode and then load FIT
> image u-boot.itb from SD card into RAM.
>
> U-Boot SPL expects u-boot.itb FIT image at the starting of SD card sector
> number (0x822) of GUID type "2E54B353-1271-4842-806F-E436D6AF6985"
>
> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
> ---
> configs/sifive_fu540_defconfig | 9 +++++++++
> 1 file changed, 9 insertions(+)
>
> diff --git a/configs/sifive_fu540_defconfig b/configs/sifive_fu540_defconfig
> index f805aacc7a..30fac8996b 100644
> --- a/configs/sifive_fu540_defconfig
> +++ b/configs/sifive_fu540_defconfig
> @@ -1,6 +1,12 @@
> CONFIG_RISCV=y
> +CONFIG_SPL_GPIO_SUPPORT=y
> +CONFIG_SYS_MALLOC_F_LEN=0x3000
> CONFIG_ENV_SIZE=0x20000
> +CONFIG_SPL_MMC_SUPPORT=y
> CONFIG_NR_DRAM_BANKS=1
> +CONFIG_SPL=y
> +CONFIG_SPL_SPI_SUPPORT=y
> +CONFIG_SPL_PAYLOAD="u-boot.itb"
> CONFIG_TARGET_SIFIVE_FU540=y
> CONFIG_ARCH_RV64I=y
> CONFIG_RISCV_SMODE=y
> @@ -9,7 +15,10 @@ CONFIG_FIT=y
> CONFIG_MISC_INIT_R=y
> CONFIG_DISPLAY_CPUINFO=y
> CONFIG_DISPLAY_BOARDINFO=y
> +CONFIG_SPL_SEPARATE_BSS=y
> +CONFIG_SPL_YMODEM_SUPPORT=y
Is this needed for SPL?
> CONFIG_OF_BOARD_FIXUP=y
> CONFIG_DEFAULT_DEVICE_TREE="hifive-unleashed-a00"
> CONFIG_SYS_RELOC_GD_ENV_ADDR=y
> +CONFIG_SPL_CLK=y
> CONFIG_DM_MTD=y
Regards,
Bin
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 20/22] riscv: sifive: fu540: enable all cache ways from U-Boot proper
2020-05-02 10:06 ` [PATCH v7 20/22] riscv: sifive: fu540: enable all cache ways from U-Boot proper Pragnesh Patel
@ 2020-05-02 12:55 ` Bin Meng
2020-05-02 14:34 ` Pragnesh Patel
0 siblings, 1 reply; 118+ messages in thread
From: Bin Meng @ 2020-05-02 12:55 UTC (permalink / raw)
To: u-boot
On Sat, May 2, 2020 at 6:09 PM Pragnesh Patel <pragnesh.patel@sifive.com> wrote:
>
> Enable all cache ways from U-Boot proper.
>
> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
> ---
> arch/riscv/cpu/fu540/Makefile | 1 +
> arch/riscv/cpu/fu540/cache.c | 53 +++++++++++++++++++++++
> arch/riscv/include/asm/arch-fu540/cache.h | 14 ++++++
> board/sifive/fu540/fu540.c | 10 ++++-
> 4 files changed, 76 insertions(+), 2 deletions(-)
> create mode 100644 arch/riscv/cpu/fu540/cache.c
> create mode 100644 arch/riscv/include/asm/arch-fu540/cache.h
>
> diff --git a/arch/riscv/cpu/fu540/Makefile b/arch/riscv/cpu/fu540/Makefile
> index 043fb961a5..088205ef57 100644
> --- a/arch/riscv/cpu/fu540/Makefile
> +++ b/arch/riscv/cpu/fu540/Makefile
> @@ -8,4 +8,5 @@ obj-y += spl.o
> else
> obj-y += dram.o
> obj-y += cpu.o
> +obj-y += cache.o
> endif
> diff --git a/arch/riscv/cpu/fu540/cache.c b/arch/riscv/cpu/fu540/cache.c
> new file mode 100644
> index 0000000000..d2dae7f17a
> --- /dev/null
> +++ b/arch/riscv/cpu/fu540/cache.c
> @@ -0,0 +1,53 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (C) 2020 SiFive, Inc
> + *
> + * Authors:
> + * Pragnesh Patel <pragnesh.patel@sifive.com>
> + */
> +
> +#include <common.h>
> +#include <asm/io.h>
> +#include <linux/bitops.h>
> +
> +/* Register offsets */
> +#define CACHE_CONFIG 0x000
> +#define CACHE_ENABLE 0x008
> +
> +#define MASK_NUM_WAYS GENMASK(15, 8)
> +#define NUM_WAYS_SHIFT 8
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +int cache_enable_ways(void)
> +{
> + const void *blob = gd->fdt_blob;
> + int node = (-FDT_ERR_NOTFOUND);
> + fdt_addr_t base;
> + u32 config;
> + u32 ways;
> +
> + volatile u32 *enable;
> +
> + node = fdt_node_offset_by_compatible(blob, -1,
> + "sifive,fu540-c000-ccache");
> +
> + if (node < 0)
> + return node;
> +
> + base = fdtdec_get_addr(blob, node, "reg");
> + if (base == FDT_ADDR_T_NONE)
> + return FDT_ADDR_T_NONE;
> +
> + config = readl((volatile u32 *)base + CACHE_CONFIG);
> + ways = (config & MASK_NUM_WAYS) >> NUM_WAYS_SHIFT;
> +
> + enable = (volatile u32 *)(base + CACHE_ENABLE);
> +
> + /* memory barrier */
> + mb();
> + (*enable) = ways - 1;
> + /* memory barrier */
> + mb();
> + return 0;
> +}
> diff --git a/arch/riscv/include/asm/arch-fu540/cache.h b/arch/riscv/include/asm/arch-fu540/cache.h
> new file mode 100644
> index 0000000000..135a17c679
> --- /dev/null
> +++ b/arch/riscv/include/asm/arch-fu540/cache.h
> @@ -0,0 +1,14 @@
> +/* SPDX-License-Identifier: GPL-2.0+ */
> +/*
> + * Copyright (C) 2020 SiFive, Inc.
> + *
> + * Authors:
> + * Pragnesh Patel <pragnesh.patel@sifve.com>
> + */
> +
> +#ifndef _CACHE_SIFIVE_H
> +#define _CACHE_SIFIVE_H
> +
> +int cache_enable_ways(void);
> +
> +#endif /* _CACHE_SIFIVE_H */
> diff --git a/board/sifive/fu540/fu540.c b/board/sifive/fu540/fu540.c
> index d05529a86b..131fee8898 100644
> --- a/board/sifive/fu540/fu540.c
> +++ b/board/sifive/fu540/fu540.c
> @@ -12,6 +12,7 @@
> #include <linux/io.h>
> #include <misc.h>
> #include <spl.h>
> +#include <asm/arch/cache.h>
>
> /*
> * This define is a value used for error/unknown serial.
> @@ -111,8 +112,13 @@ int misc_init_r(void)
>
> int board_init(void)
> {
> - /* For now nothing to do here. */
> -
> + int ret;
nits: need a blank line
> + /* enable all cache ways */
> + ret = cache_enable_ways();
> + if (ret) {
> + debug("%s: could not enable cache ways\n", __func__);
> + return ret;
> + }
nits: need a blank line
> return 0;
> }
>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Regards,
Bin
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 21/22] doc: sifive: fu540: Add description for OpenSBI generic platform
2020-05-02 10:06 ` [PATCH v7 21/22] doc: sifive: fu540: Add description for OpenSBI generic platform Pragnesh Patel
@ 2020-05-02 12:55 ` Bin Meng
2020-05-02 14:30 ` Pragnesh Patel
0 siblings, 1 reply; 118+ messages in thread
From: Bin Meng @ 2020-05-02 12:55 UTC (permalink / raw)
To: u-boot
Hi Pragnesh,
On Sat, May 2, 2020 at 6:09 PM Pragnesh Patel <pragnesh.patel@sifive.com> wrote:
>
> OpenSBI generic platform support provides platform specific
> functionality based on the FDT passed by previous booting stage.
>
> depends on OpenSBI commit:
> platform: Add generic FDT based platform support
> (sha1: f1aa9e54e00006ae70aeac638d5b75093520f65d)
>
> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
> ---
> doc/board/sifive/fu540.rst | 19 +++++++++++++------
> 1 file changed, 13 insertions(+), 6 deletions(-)
>
> diff --git a/doc/board/sifive/fu540.rst b/doc/board/sifive/fu540.rst
> index 610ba87074..1c3d4740f3 100644
> --- a/doc/board/sifive/fu540.rst
> +++ b/doc/board/sifive/fu540.rst
> @@ -22,14 +22,21 @@ The support for following drivers are already enabled:
>
> TODO:
>
> -1. U-Boot expects the serial console device entry to be present under /chosen
> - DT node. Without a serial console U-Boot will panic. Example:
> +1. The DTB passed by U-Boot SPL or FSBL to OpenSBI should have CLINT
> + DT node and the "/chosen" DT node should have "stdout-path" DT
> + property.
>
> .. code-block:: none
>
> - chosen {
> - stdout-path = "/soc/serial at 10010000:115200";
> - };
> + chosen {
> + stdout-path = "/soc/serial at 10010000:115200";
> + };
> +
> + clint at 2000000 {
> + compatible = "riscv,clint0";
> + interrupts-extended = <&cpu0_intc 3 &cpu0_intc 7 &cpu1_intc 3 &cpu1_intc 7 &cpu2_intc 3 &cpu2_intc 7 &cpu3_intc 3 &cpu3_intc 7 &cpu4_intc 3 &cpu4_intc 7>;
> + reg = <0x0 0x2000000 0x0 0xc0000>;
> + };
Can we update the U-Boot dtsi to include the changes?
>
> Building
> --------
> @@ -58,7 +65,7 @@ firmware. We need to compile OpenSBI with below command:
>
> .. code-block:: none
>
> -make PLATFORM=sifive/fu540 FW_PAYLOAD_PATH=<path to u-boot-dtb.bin>
> + make PLATFORM=generic FW_PAYLOAD_PATH=<path to u-boot-dtb.bin>
>
> More detailed description of steps required to build FW_PAYLOAD firmware
> is beyond the scope of this document. Please refer OpenSBI documenation.
Regards,
Bin
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 22/22] doc: sifive: fu540: Add description for RISC-V FU540 U-Boot SPL
2020-05-02 10:06 ` [PATCH v7 22/22] doc: sifive: fu540: Add description for RISC-V FU540 U-Boot SPL Pragnesh Patel
@ 2020-05-02 12:55 ` Bin Meng
2020-05-02 16:22 ` Jagan Teki
2020-05-03 4:34 ` Anup Patel
2 siblings, 0 replies; 118+ messages in thread
From: Bin Meng @ 2020-05-02 12:55 UTC (permalink / raw)
To: u-boot
On Sat, May 2, 2020 at 6:09 PM Pragnesh Patel <pragnesh.patel@sifive.com> wrote:
>
> Add descriptions about U-Boot SPL feature and how to build and run
> from MMC.
>
> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
> ---
> doc/board/sifive/fu540.rst | 376 +++++++++++++++++++++++++++++++++++++
> 1 file changed, 376 insertions(+)
>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 04/22] lib: Makefile: build crc7.c when CONFIG_MMC_SPI
2020-05-02 11:47 ` Bin Meng
@ 2020-05-02 12:58 ` Heinrich Schuchardt
2020-05-02 15:33 ` Jagan Teki
2020-05-03 9:54 ` Pragnesh Patel
0 siblings, 2 replies; 118+ messages in thread
From: Heinrich Schuchardt @ 2020-05-02 12:58 UTC (permalink / raw)
To: u-boot
Am May 2, 2020 11:47:10 AM UTC schrieb Bin Meng <bmeng.cn@gmail.com>:
>Hi Heinrich,
>
>On Sat, May 2, 2020 at 6:30 PM Heinrich Schuchardt <xypron.glpk@gmx.de>
>wrote:
>>
>> On 5/2/20 12:06 PM, Pragnesh Patel wrote:
>> > When build U-Boot SPL, meet an issue of undefined reference to
>> > 'crc7' for drivers/mmc/mmc_spi.c, so let's compile crc7.c when
>> > CONFIG_MMC_SPI selected.
>> >
>> > Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
>> > Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
>> > Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
>> > ---
>> > common/spl/Kconfig | 6 ++++++
>> > drivers/mmc/Kconfig | 1 +
>> > lib/Makefile | 1 +
>> > 3 files changed, 8 insertions(+)
>> >
>> > diff --git a/common/spl/Kconfig b/common/spl/Kconfig
>> > index ef5bf66696..d1f0e6bc4c 100644
>> > --- a/common/spl/Kconfig
>> > +++ b/common/spl/Kconfig
>> > @@ -401,6 +401,12 @@ config SPL_CRC32_SUPPORT
>> > for detected accidental image corruption. For secure
>applications you
>> > should consider SHA1 or SHA256.
>> >
>> > +config SPL_CRC7_SUPPORT
>> > + bool "Support CRC7"
>> > + help
>> > + Enable CRC7 hashing for drivers which are using in SPL.
>> > + This is a 32-bit checksum value that can be used to verify
>images.
>> > +
>> > config SPL_MD5_SUPPORT
>> > bool "Support MD5"
>> > depends on SPL_FIT
>> > diff --git a/drivers/mmc/Kconfig b/drivers/mmc/Kconfig
>> > index 8f0df568b9..139599072a 100644
>> > --- a/drivers/mmc/Kconfig
>> > +++ b/drivers/mmc/Kconfig
>> > @@ -49,6 +49,7 @@ if MMC
>> > config MMC_SPI
>> > bool "Support for SPI-based MMC controller"
>> > depends on DM_MMC && DM_SPI
>> > + select SPL_CRC7_SUPPORT if SPL
>> > help
>> > This selects SPI-based MMC controllers.
>> > If you have an MMC controller on a SPI bus, say Y here.
>> > diff --git a/lib/Makefile b/lib/Makefile
>> > index c6f862b0c2..fcd934857f 100644
>> > --- a/lib/Makefile
>> > +++ b/lib/Makefile
>> > @@ -80,6 +80,7 @@ endif
>> >
>> > ifdef CONFIG_SPL_BUILD
>> > obj-$(CONFIG_SPL_YMODEM_SUPPORT) += crc16.o
>> > +obj-$(CONFIG_SPL_CRC7_SUPPORT) += crc7.o
>>
>> crc7.o is not needed in main U-Boot if MMC_SPI is not selected.
>>
>> So instead of adding a new configuration variable simply correct the
>> existing line in lib/Makefile
>>
>> -obj-y += crc7.o
>> +obj-$(CONFIG_MMC_SPI) += crc7.o
>
>This looks incorrect to me. CRC7 can be useful for other drivers too.
>It should not depend on CONFIG_MMC_SPI.
Using this argument you would always compile everything. Compiling files that are not used is simply a waste of CPU time.
Following your argument. you could also always compile crc7.c for SPL and hope the compiler will eliminate it.
Either way we do not need a new config symbol.
Best regards
Heinrich
>
>>
>> and move that line inside lib/Makefile so that is does not depend on
>> CONFIG_SPL_BUILD.
>>
>
>Regards,
>Bin
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 21/22] doc: sifive: fu540: Add description for OpenSBI generic platform
2020-05-02 12:55 ` Bin Meng
@ 2020-05-02 14:30 ` Pragnesh Patel
2020-05-02 15:16 ` Bin Meng
0 siblings, 1 reply; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-02 14:30 UTC (permalink / raw)
To: u-boot
Hi Bin,
>-----Original Message-----
>From: Bin Meng <bmeng.cn@gmail.com>
>Sent: 02 May 2020 18:26
>To: Pragnesh Patel <pragnesh.patel@sifive.com>
>Cc: U-Boot Mailing List <u-boot@lists.denx.de>; Atish Patra
><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Paul
>Walmsley <paul.walmsley@sifive.com>; Jagan Teki
><jagan@amarulasolutions.com>; Troy Benjegerdes
><troy.benjegerdes@sifive.com>; Anup Patel <anup.patel@wdc.com>; Sagar
>Kadam <sagar.kadam@sifive.com>; Rick Chen <rick@andestech.com>
>Subject: Re: [PATCH v7 21/22] doc: sifive: fu540: Add description for OpenSBI
>generic platform
>
>[External Email] Do not click links or attachments unless you recognize the
>sender and know the content is safe
>
>Hi Pragnesh,
>
>On Sat, May 2, 2020 at 6:09 PM Pragnesh Patel <pragnesh.patel@sifive.com>
>wrote:
>>
>> OpenSBI generic platform support provides platform specific
>> functionality based on the FDT passed by previous booting stage.
>>
>> depends on OpenSBI commit:
>> platform: Add generic FDT based platform support
>> (sha1: f1aa9e54e00006ae70aeac638d5b75093520f65d)
>>
>> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
>> ---
>> doc/board/sifive/fu540.rst | 19 +++++++++++++------
>> 1 file changed, 13 insertions(+), 6 deletions(-)
>>
>> diff --git a/doc/board/sifive/fu540.rst b/doc/board/sifive/fu540.rst
>> index 610ba87074..1c3d4740f3 100644
>> --- a/doc/board/sifive/fu540.rst
>> +++ b/doc/board/sifive/fu540.rst
>> @@ -22,14 +22,21 @@ The support for following drivers are already
>enabled:
>>
>> TODO:
>>
>> -1. U-Boot expects the serial console device entry to be present under
>/chosen
>> - DT node. Without a serial console U-Boot will panic. Example:
>> +1. The DTB passed by U-Boot SPL or FSBL to OpenSBI should have CLINT
>> + DT node and the "/chosen" DT node should have "stdout-path" DT
>> + property.
>>
>> .. code-block:: none
>>
>> - chosen {
>> - stdout-path = "/soc/serial at 10010000:115200";
>> - };
>> + chosen {
>> + stdout-path = "/soc/serial at 10010000:115200";
>> + };
>> +
>> + clint at 2000000 {
>> + compatible = "riscv,clint0";
>> + interrupts-extended = <&cpu0_intc 3 &cpu0_intc 7 &cpu1_intc 3
>&cpu1_intc 7 &cpu2_intc 3 &cpu2_intc 7 &cpu3_intc 3 &cpu3_intc 7
>&cpu4_intc 3 &cpu4_intc 7>;
>> + reg = <0x0 0x2000000 0x0 0xc0000>;
>> + };
>
>Can we update the U-Boot dtsi to include the changes?
Can you please clarify which dtsi fu540-c000-u-boot.dtsi or fu540-c000.dtsi ?
I have already added clint DT node in "arch/riscv/dts/fu540-c000-u-boot.dtsi"
>
>>
>> Building
>> --------
>> @@ -58,7 +65,7 @@ firmware. We need to compile OpenSBI with below
>command:
>>
>> .. code-block:: none
>>
>> -make PLATFORM=sifive/fu540 FW_PAYLOAD_PATH=<path to u-boot-
>dtb.bin>
>> + make PLATFORM=generic FW_PAYLOAD_PATH=<path to u-boot-
>dtb.bin>
>>
>> More detailed description of steps required to build FW_PAYLOAD
>> firmware is beyond the scope of this document. Please refer OpenSBI
>documenation.
>
>Regards,
>Bin
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 20/22] riscv: sifive: fu540: enable all cache ways from U-Boot proper
2020-05-02 12:55 ` Bin Meng
@ 2020-05-02 14:34 ` Pragnesh Patel
0 siblings, 0 replies; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-02 14:34 UTC (permalink / raw)
To: u-boot
Hi Bin,
>-----Original Message-----
>From: Bin Meng <bmeng.cn@gmail.com>
>Sent: 02 May 2020 18:26
>To: Pragnesh Patel <pragnesh.patel@sifive.com>
>Cc: U-Boot Mailing List <u-boot@lists.denx.de>; Atish Patra
><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Paul
>Walmsley <paul.walmsley@sifive.com>; Jagan Teki
><jagan@amarulasolutions.com>; Troy Benjegerdes
><troy.benjegerdes@sifive.com>; Anup Patel <anup.patel@wdc.com>; Sagar
>Kadam <sagar.kadam@sifive.com>; Rick Chen <rick@andestech.com>; Palmer
>Dabbelt <palmer@dabbelt.com>
>Subject: Re: [PATCH v7 20/22] riscv: sifive: fu540: enable all cache ways from
>U-Boot proper
>
>[External Email] Do not click links or attachments unless you recognize the
>sender and know the content is safe
>
>On Sat, May 2, 2020 at 6:09 PM Pragnesh Patel <pragnesh.patel@sifive.com>
>wrote:
>>
>> Enable all cache ways from U-Boot proper.
>>
>> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
>> ---
>> arch/riscv/cpu/fu540/Makefile | 1 +
>> arch/riscv/cpu/fu540/cache.c | 53 +++++++++++++++++++++++
>> arch/riscv/include/asm/arch-fu540/cache.h | 14 ++++++
>> board/sifive/fu540/fu540.c | 10 ++++-
>> 4 files changed, 76 insertions(+), 2 deletions(-) create mode 100644
>> arch/riscv/cpu/fu540/cache.c create mode 100644
>> arch/riscv/include/asm/arch-fu540/cache.h
>>
>> diff --git a/arch/riscv/cpu/fu540/Makefile
>> b/arch/riscv/cpu/fu540/Makefile index 043fb961a5..088205ef57 100644
>> --- a/arch/riscv/cpu/fu540/Makefile
>> +++ b/arch/riscv/cpu/fu540/Makefile
>> @@ -8,4 +8,5 @@ obj-y += spl.o
>> else
>> obj-y += dram.o
>> obj-y += cpu.o
>> +obj-y += cache.o
>> endif
>> diff --git a/arch/riscv/cpu/fu540/cache.c
>> b/arch/riscv/cpu/fu540/cache.c new file mode 100644 index
>> 0000000000..d2dae7f17a
>> --- /dev/null
>> +++ b/arch/riscv/cpu/fu540/cache.c
>> @@ -0,0 +1,53 @@
>> +// SPDX-License-Identifier: GPL-2.0+
>> +/*
>> + * Copyright (C) 2020 SiFive, Inc
>> + *
>> + * Authors:
>> + * Pragnesh Patel <pragnesh.patel@sifive.com>
>> + */
>> +
>> +#include <common.h>
>> +#include <asm/io.h>
>> +#include <linux/bitops.h>
>> +
>> +/* Register offsets */
>> +#define CACHE_CONFIG 0x000
>> +#define CACHE_ENABLE 0x008
>> +
>> +#define MASK_NUM_WAYS GENMASK(15, 8) #define NUM_WAYS_SHIFT 8
>> +
>> +DECLARE_GLOBAL_DATA_PTR;
>> +
>> +int cache_enable_ways(void)
>> +{
>> + const void *blob = gd->fdt_blob;
>> + int node = (-FDT_ERR_NOTFOUND);
>> + fdt_addr_t base;
>> + u32 config;
>> + u32 ways;
>> +
>> + volatile u32 *enable;
>> +
>> + node = fdt_node_offset_by_compatible(blob, -1,
>> +
>> + "sifive,fu540-c000-ccache");
>> +
>> + if (node < 0)
>> + return node;
>> +
>> + base = fdtdec_get_addr(blob, node, "reg");
>> + if (base == FDT_ADDR_T_NONE)
>> + return FDT_ADDR_T_NONE;
>> +
>> + config = readl((volatile u32 *)base + CACHE_CONFIG);
>> + ways = (config & MASK_NUM_WAYS) >> NUM_WAYS_SHIFT;
>> +
>> + enable = (volatile u32 *)(base + CACHE_ENABLE);
>> +
>> + /* memory barrier */
>> + mb();
>> + (*enable) = ways - 1;
>> + /* memory barrier */
>> + mb();
>> + return 0;
>> +}
>> diff --git a/arch/riscv/include/asm/arch-fu540/cache.h
>> b/arch/riscv/include/asm/arch-fu540/cache.h
>> new file mode 100644
>> index 0000000000..135a17c679
>> --- /dev/null
>> +++ b/arch/riscv/include/asm/arch-fu540/cache.h
>> @@ -0,0 +1,14 @@
>> +/* SPDX-License-Identifier: GPL-2.0+ */
>> +/*
>> + * Copyright (C) 2020 SiFive, Inc.
>> + *
>> + * Authors:
>> + * Pragnesh Patel <pragnesh.patel@sifve.com>
>> + */
>> +
>> +#ifndef _CACHE_SIFIVE_H
>> +#define _CACHE_SIFIVE_H
>> +
>> +int cache_enable_ways(void);
>> +
>> +#endif /* _CACHE_SIFIVE_H */
>> diff --git a/board/sifive/fu540/fu540.c b/board/sifive/fu540/fu540.c
>> index d05529a86b..131fee8898 100644
>> --- a/board/sifive/fu540/fu540.c
>> +++ b/board/sifive/fu540/fu540.c
>> @@ -12,6 +12,7 @@
>> #include <linux/io.h>
>> #include <misc.h>
>> #include <spl.h>
>> +#include <asm/arch/cache.h>
>>
>> /*
>> * This define is a value used for error/unknown serial.
>> @@ -111,8 +112,13 @@ int misc_init_r(void)
>>
>> int board_init(void)
>> {
>> - /* For now nothing to do here. */
>> -
>> + int ret;
>
>nits: need a blank line
Will update in v8.
>
>> + /* enable all cache ways */
>> + ret = cache_enable_ways();
>> + if (ret) {
>> + debug("%s: could not enable cache ways\n", __func__);
>> + return ret;
>> + }
>
>nits: need a blank line
Will update in v8.
>
>> return 0;
>> }
>>
>
>Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
>
>Regards,
>Bin
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 18/22] configs: fu540: Add config options for U-Boot SPL
2020-05-02 12:55 ` Bin Meng
@ 2020-05-02 14:37 ` Pragnesh Patel
2020-05-02 17:04 ` Jagan Teki
1 sibling, 0 replies; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-02 14:37 UTC (permalink / raw)
To: u-boot
HI Bin,
>-----Original Message-----
>From: Bin Meng <bmeng.cn@gmail.com>
>Sent: 02 May 2020 18:26
>To: Pragnesh Patel <pragnesh.patel@sifive.com>
>Cc: U-Boot Mailing List <u-boot@lists.denx.de>; Atish Patra
><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Paul
>Walmsley <paul.walmsley@sifive.com>; Jagan Teki
><jagan@amarulasolutions.com>; Troy Benjegerdes
><troy.benjegerdes@sifive.com>; Anup Patel <anup.patel@wdc.com>; Sagar
>Kadam <sagar.kadam@sifive.com>; Rick Chen <rick@andestech.com>; Palmer
>Dabbelt <palmer@dabbelt.com>
>Subject: Re: [PATCH v7 18/22] configs: fu540: Add config options for U-Boot
>SPL
>
>[External Email] Do not click links or attachments unless you recognize the
>sender and know the content is safe
>
>Hi Pragnesh,
>
>On Sat, May 2, 2020 at 6:08 PM Pragnesh Patel <pragnesh.patel@sifive.com>
>wrote:
>>
>> With sifive_fu540_defconfig:
>>
>> User can use FSBL or u-boot-spl.bin anyone at a time.
>>
>> For FSBL,
>> fsbl->fw_payload.bin (opensbi + U-Boot)
>>
>> For u-boot-spl.bin,
>> u-boot-spl.bin->FIT image (opensbi + U-Boot + dtb)
>>
>> U-Boot SPL will be loaded by ZSBL from SD card (replace fsbl.bin with
>> u-boot-spl.bin) and runs in L2 LIM in machine mode and then load FIT
>> image u-boot.itb from SD card into RAM.
>>
>> U-Boot SPL expects u-boot.itb FIT image at the starting of SD card
>> sector number (0x822) of GUID type "2E54B353-1271-4842-806F-
>E436D6AF6985"
>>
>> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
>> ---
>> configs/sifive_fu540_defconfig | 9 +++++++++
>> 1 file changed, 9 insertions(+)
>>
>> diff --git a/configs/sifive_fu540_defconfig
>> b/configs/sifive_fu540_defconfig index f805aacc7a..30fac8996b 100644
>> --- a/configs/sifive_fu540_defconfig
>> +++ b/configs/sifive_fu540_defconfig
>> @@ -1,6 +1,12 @@
>> CONFIG_RISCV=y
>> +CONFIG_SPL_GPIO_SUPPORT=y
>> +CONFIG_SYS_MALLOC_F_LEN=0x3000
>> CONFIG_ENV_SIZE=0x20000
>> +CONFIG_SPL_MMC_SUPPORT=y
>> CONFIG_NR_DRAM_BANKS=1
>> +CONFIG_SPL=y
>> +CONFIG_SPL_SPI_SUPPORT=y
>> +CONFIG_SPL_PAYLOAD="u-boot.itb"
>> CONFIG_TARGET_SIFIVE_FU540=y
>> CONFIG_ARCH_RV64I=y
>> CONFIG_RISCV_SMODE=y
>> @@ -9,7 +15,10 @@ CONFIG_FIT=y
>> CONFIG_MISC_INIT_R=y
>> CONFIG_DISPLAY_CPUINFO=y
>> CONFIG_DISPLAY_BOARDINFO=y
>> +CONFIG_SPL_SEPARATE_BSS=y
>> +CONFIG_SPL_YMODEM_SUPPORT=y
>
>Is this needed for SPL?
No, it's not needed. Will check and remove in v8.
>
>> CONFIG_OF_BOARD_FIXUP=y
>> CONFIG_DEFAULT_DEVICE_TREE="hifive-unleashed-a00"
>> CONFIG_SYS_RELOC_GD_ENV_ADDR=y
>> +CONFIG_SPL_CLK=y
>> CONFIG_DM_MTD=y
>
>Regards,
>Bin
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 13/22] riscv: cpu: fu540: Add support for cpu fu540
2020-05-02 12:32 ` Bin Meng
@ 2020-05-02 14:38 ` Pragnesh Patel
0 siblings, 0 replies; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-02 14:38 UTC (permalink / raw)
To: u-boot
Hi Bin,
>-----Original Message-----
>From: Bin Meng <bmeng.cn@gmail.com>
>Sent: 02 May 2020 18:03
>To: Pragnesh Patel <pragnesh.patel@sifive.com>
>Cc: U-Boot Mailing List <u-boot@lists.denx.de>; Atish Patra
><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Paul
>Walmsley <paul.walmsley@sifive.com>; Jagan Teki
><jagan@amarulasolutions.com>; Troy Benjegerdes
><troy.benjegerdes@sifive.com>; Anup Patel <anup.patel@wdc.com>; Sagar
>Kadam <sagar.kadam@sifive.com>; Rick Chen <rick@andestech.com>; Lukas
>Auer <lukas.auer@aisec.fraunhofer.de>; Simon Glass <sjg@chromium.org>
>Subject: Re: [PATCH v7 13/22] riscv: cpu: fu540: Add support for cpu fu540
>
>[External Email] Do not click links or attachments unless you recognize the
>sender and know the content is safe
>
>Hi Pragnesh,
>
>On Sat, May 2, 2020 at 6:08 PM Pragnesh Patel <pragnesh.patel@sifive.com>
>wrote:
>>
>> Add SiFive fu540 cpu to support RISC-V arch
>>
>> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
>> ---
>> arch/riscv/Kconfig | 1 +
>> arch/riscv/cpu/fu540/Kconfig | 15 ++++++++++++++
>> arch/riscv/cpu/fu540/Makefile | 7 +++++++
>> arch/riscv/cpu/fu540/cpu.c | 22 ++++++++++++++++++++
>> arch/riscv/cpu/fu540/dram.c | 38
>+++++++++++++++++++++++++++++++++++
>> 5 files changed, 83 insertions(+)
>> create mode 100644 arch/riscv/cpu/fu540/Kconfig create mode 100644
>> arch/riscv/cpu/fu540/Makefile create mode 100644
>> arch/riscv/cpu/fu540/cpu.c create mode 100644
>> arch/riscv/cpu/fu540/dram.c
>>
>> diff --git a/arch/riscv/Kconfig b/arch/riscv/Kconfig index
>> fb5fe5afff..3044609971 100644
>> --- a/arch/riscv/Kconfig
>> +++ b/arch/riscv/Kconfig
>> @@ -57,6 +57,7 @@ source "board/sifive/fu540/Kconfig"
>> # platform-specific options below
>> source "arch/riscv/cpu/ax25/Kconfig"
>> source "arch/riscv/cpu/generic/Kconfig"
>> +source "arch/riscv/cpu/fu540/Kconfig"
>>
>> # architecture-specific options below
>>
>> diff --git a/arch/riscv/cpu/fu540/Kconfig
>> b/arch/riscv/cpu/fu540/Kconfig new file mode 100644 index
>> 0000000000..b2cb155d6d
>> --- /dev/null
>> +++ b/arch/riscv/cpu/fu540/Kconfig
>> @@ -0,0 +1,15 @@
>> +# SPDX-License-Identifier: GPL-2.0+
>> +#
>> +# Copyright (C) 2018, Bin Meng <bmeng.cn@gmail.com>
>> +
>> +config GENERIC_RISCV
>
>This should be SIFIVE_FU540
Will update in v8, thanks for the review.
>
>> + bool
>> + select ARCH_EARLY_INIT_R
>> + imply CPU
>> + imply CPU_RISCV
>> + imply RISCV_TIMER
>> + imply SIFIVE_CLINT if (RISCV_MMODE || SPL_RISCV_MMODE)
>> + imply CMD_CPU
>> + imply SPL_CPU_SUPPORT
>> + imply SPL_OPENSBI
>> + imply SPL_LOAD_FIT
>> diff --git a/arch/riscv/cpu/fu540/Makefile
>> b/arch/riscv/cpu/fu540/Makefile new file mode 100644 index
>> 0000000000..44700d998c
>> --- /dev/null
>> +++ b/arch/riscv/cpu/fu540/Makefile
>> @@ -0,0 +1,7 @@
>> +# SPDX-License-Identifier: GPL-2.0+
>> +#
>> +# Copyright (C) 2020 SiFive, Inc
>> +# Pragnesh Patel <pragnesh.patel@sifive.com>
>> +
>> +obj-y += dram.o
>> +obj-y += cpu.o
>> diff --git a/arch/riscv/cpu/fu540/cpu.c b/arch/riscv/cpu/fu540/cpu.c
>> new file mode 100644 index 0000000000..13a69ef0cc
>> --- /dev/null
>> +++ b/arch/riscv/cpu/fu540/cpu.c
>> @@ -0,0 +1,22 @@
>> +// SPDX-License-Identifier: GPL-2.0+
>> +/*
>> + * Copyright (C) 2018, Bin Meng <bmeng.cn@gmail.com> */
>> +
>> +#include <common.h>
>> +#include <irq_func.h>
>> +
>> +/*
>> + * cleanup_before_linux() is called just before we call linux
>> + * it prepares the processor for linux
>> + *
>> + * we disable interrupt and caches.
>> + */
>> +int cleanup_before_linux(void)
>> +{
>> + disable_interrupts();
>> +
>> + cache_flush();
>> +
>> + return 0;
>> +}
>> diff --git a/arch/riscv/cpu/fu540/dram.c b/arch/riscv/cpu/fu540/dram.c
>> new file mode 100644 index 0000000000..1dc77efeca
>> --- /dev/null
>> +++ b/arch/riscv/cpu/fu540/dram.c
>> @@ -0,0 +1,38 @@
>> +// SPDX-License-Identifier: GPL-2.0+
>> +/*
>> + * Copyright (C) 2018, Bin Meng <bmeng.cn@gmail.com> */
>> +
>> +#include <common.h>
>> +#include <fdtdec.h>
>> +#include <init.h>
>> +#include <linux/sizes.h>
>> +
>> +DECLARE_GLOBAL_DATA_PTR;
>> +
>> +int dram_init(void)
>> +{
>> + return fdtdec_setup_mem_size_base(); }
>> +
>> +int dram_init_banksize(void)
>> +{
>> + return fdtdec_setup_memory_banksize(); }
>> +
>> +ulong board_get_usable_ram_top(ulong total_size) { #ifdef
>> +CONFIG_64BIT
>> + /*
>> + * Ensure that we run from first 4GB so that all
>> + * addresses used by U-Boot are 32bit addresses.
>> + *
>> + * This in-turn ensures that 32bit DMA capable
>> + * devices work fine because DMA mapping APIs will
>> + * provide 32bit DMA addresses only.
>> + */
>> + if (gd->ram_top > SZ_4G)
>> + return SZ_4G;
>> +#endif
>> + return gd->ram_top;
>> +}
>
>Other than that,
>Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
>
>Regards,
>Bin
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 07/22] sifive: dts: fu540: Add DDR controller and phy register settings
2020-05-02 12:28 ` Bin Meng
@ 2020-05-02 14:41 ` Pragnesh Patel
0 siblings, 0 replies; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-02 14:41 UTC (permalink / raw)
To: u-boot
Hi Bin,
>-----Original Message-----
>From: Bin Meng <bmeng.cn@gmail.com>
>Sent: 02 May 2020 17:59
>To: Pragnesh Patel <pragnesh.patel@sifive.com>
>Cc: U-Boot Mailing List <u-boot@lists.denx.de>; Atish Patra
><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Paul
>Walmsley <paul.walmsley@sifive.com>; Jagan Teki
><jagan@amarulasolutions.com>; Troy Benjegerdes
><troy.benjegerdes@sifive.com>; Anup Patel <anup.patel@wdc.com>; Sagar
>Kadam <sagar.kadam@sifive.com>; Rick Chen <rick@andestech.com>
>Subject: Re: [PATCH v7 07/22] sifive: dts: fu540: Add DDR controller and phy
>register settings
>
>[External Email] Do not click links or attachments unless you recognize the
>sender and know the content is safe
>
>On Sat, May 2, 2020 at 6:08 PM Pragnesh Patel <pragnesh.patel@sifive.com>
>wrote:
>>
>> Add DDR controller and phy register settings, taken from fsbl
>> (https://github.com/sifive/freedom-u540-c000-bootloader.git)
>>
>> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
>> ---
>> ...fu540-hifive-unleashed-a00-sdram-ddr4.dtsi | 1489 +++++++++++++++++
>> 1 file changed, 1489 insertions(+)
>> create mode 100644 arch/riscv/dts/fu540-hifive-unleashed-a00-sdram-
>ddr4.dtsi
>>
>> diff --git a/arch/riscv/dts/fu540-hifive-unleashed-a00-sdram-ddr4.dtsi
>b/arch/riscv/dts/fu540-hifive-unleashed-a00-sdram-ddr4.dtsi
>> new file mode 100644
>> index 0000000000..370c53800d
>> --- /dev/null
>> +++ b/arch/riscv/dts/fu540-hifive-unleashed-a00-sdram-ddr4.dtsi
>> @@ -0,0 +1,1489 @@
>> +// SPDX-License-Identifier: GPL-2.0+
>
>Should this file be dual-licensed?
Yes, will update in v8.
>
>> +/*
>> + * (C) Copyright 2020 SiFive, Inc
>> + */
>> +
>
>Tested-by: Bin Meng <bmeng.cn@gmail.com>
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 10/22] clk: sifive: fu540-prci: ddr and ethernet clock initialization in SPL
2020-05-02 12:28 ` Bin Meng
@ 2020-05-02 14:49 ` Pragnesh Patel
2020-05-09 11:29 ` Pragnesh Patel
0 siblings, 1 reply; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-02 14:49 UTC (permalink / raw)
To: u-boot
Hi Bin,
>-----Original Message-----
>From: Bin Meng <bmeng.cn@gmail.com>
>Sent: 02 May 2020 17:58
>To: Pragnesh Patel <pragnesh.patel@sifive.com>
>Cc: U-Boot Mailing List <u-boot@lists.denx.de>; Atish Patra
><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Paul
>Walmsley <paul.walmsley@sifive.com>; Jagan Teki
><jagan@amarulasolutions.com>; Troy Benjegerdes
><troy.benjegerdes@sifive.com>; Anup Patel <anup.patel@wdc.com>; Sagar
>Kadam <sagar.kadam@sifive.com>; Rick Chen <rick@andestech.com>; Lukasz
>Majewski <lukma@denx.de>; Anatolij Gustschin <agust@denx.de>; Simon
>Glass <sjg@chromium.org>
>Subject: Re: [PATCH v7 10/22] clk: sifive: fu540-prci: ddr and ethernet clock
>initialization in SPL
>
>[External Email] Do not click links or attachments unless you recognize the
>sender and know the content is safe
>
>Hi Pragnesh,
>
>On Sat, May 2, 2020 at 6:08 PM Pragnesh Patel <pragnesh.patel@sifive.com>
>wrote:
>>
>> Add ddr clock release reset and ehternet clock initialization for SPL
>>
>> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
>> ---
>> drivers/clk/sifive/fu540-prci.c | 87
>> ++++++++++++++++++++++++++++++---
>> 1 file changed, 81 insertions(+), 6 deletions(-)
>>
>> diff --git a/drivers/clk/sifive/fu540-prci.c
>> b/drivers/clk/sifive/fu540-prci.c index bf06c3a3bb..1c89bdf242 100644
>> --- a/drivers/clk/sifive/fu540-prci.c
>> +++ b/drivers/clk/sifive/fu540-prci.c
>> @@ -41,6 +41,8 @@
>> #include <linux/clk/analogbits-wrpll-cln28hpc.h>
>> #include <dt-bindings/clock/sifive-fu540-prci.h>
>>
>> +#define MHz 1000000
>> +
>> /*
>> * EXPECTED_CLK_PARENT_COUNT: how many parent clocks this driver
>expects:
>> * hfclk and rtcclk
>> @@ -152,6 +154,12 @@
>> #define PRCI_CLKMUXSTATUSREG_TLCLKSEL_STATUS_MASK \
>> (0x1 <<
>> PRCI_CLKMUXSTATUSREG_TLCLKSEL_STATUS_SHIFT)
>>
>> +/* PROCMONCFG */
>> +#define PRCI_PROCMONCFG_OFFSET 0xF0
>> +#define PRCI_PROCMONCFG_CORE_CLOCK_SHIFT 24
>> +#define PRCI_PROCMONCFG_CORE_CLOCK_MASK \
>> + (0x1 << PRCI_PROCMONCFG_CORE_CLOCK_SHIFT)
>> +
>> /*
>> * Private structures
>> */
>> @@ -176,6 +184,7 @@ struct __prci_data {
>> * @disable_bypass: fn ptr to code to not bypass the WRPLL (or NULL)
>> * @cfg0_offs: WRPLL CFG0 register offset (in bytes) from the PRCI base
>address
>> * @cfg1_offs: WRPLL CFG1 register offset (in bytes) from the PRCI
>> base address
>> + * @release_reset: fn ptr to code to release clock reset
>> *
>> * @enable_bypass and @disable_bypass are used for WRPLL instances
>> * that contain a separate external glitchless clock mux downstream
>> @@ -187,6 +196,9 @@ struct __prci_wrpll_data {
>> void (*disable_bypass)(struct __prci_data *pd);
>> u8 cfg0_offs;
>> u8 cfg1_offs;
>> +#ifdef CONFIG_SPL_BUILD
>> + void (*release_reset)(struct __prci_data *pd); #endif
>> };
>>
>> struct __prci_clock;
>> @@ -476,6 +488,11 @@ static int sifive_fu540_prci_clock_enable(struct
>> __prci_clock *pc, bool enable)
>>
>> if (enable) {
>> __prci_wrpll_write_cfg1(pd, pwd,
>> PRCI_COREPLLCFG1_CKE_MASK);
>> +
>> +#ifdef CONFIG_SPL_BUILD
>> + if (pwd->release_reset)
>> + pwd->release_reset(pd); #endif
>> } else {
>> u32 r;
>>
>> @@ -495,11 +512,6 @@ static const struct __prci_clock_ops
>sifive_fu540_prci_wrpll_clk_ops = {
>> .enable_clk = sifive_fu540_prci_clock_enable, };
>>
>> -static const struct __prci_clock_ops sifive_fu540_prci_wrpll_ro_clk_ops = {
>> - .recalc_rate = sifive_fu540_prci_wrpll_recalc_rate,
>> - .enable_clk = sifive_fu540_prci_clock_enable,
>> -};
>> -
>> /* TLCLKSEL clock integration */
>>
>> static unsigned long sifive_fu540_prci_tlclksel_recalc_rate(
>> @@ -521,6 +533,39 @@ static const struct __prci_clock_ops
>sifive_fu540_prci_tlclksel_clk_ops = {
>> .recalc_rate = sifive_fu540_prci_tlclksel_recalc_rate,
>> };
>>
>> +#ifdef CONFIG_SPL_BUILD
>> +/**
>> + * __prci_ddr_release_reset() - Release DDR reset
>> + * @pd: struct __prci_data * for the PRCI containing the DDRCLK mux
>> +reg
>> + *
>> + */
>> +static void __prci_ddr_release_reset(struct __prci_data *pd) {
>> + u32 v;
>> +
>> + v = __prci_readl(pd, PRCI_DEVICESRESETREG_OFFSET);
>> + v |= PRCI_DEVICESRESETREG_DDR_CTRL_RST_N_MASK;
>> + __prci_writel(v, PRCI_DEVICESRESETREG_OFFSET, pd);
>> +
>> + // HACK to get the '1 full controller clock cycle'.
>
>nits: should use /* */
Will update in v8.
>
>> + asm volatile ("fence");
>> + v = __prci_readl(pd, PRCI_DEVICESRESETREG_OFFSET);
>> + v |= (PRCI_DEVICESRESETREG_DDR_AXI_RST_N_MASK |
>> + PRCI_DEVICESRESETREG_DDR_AHB_RST_N_MASK |
>> + PRCI_DEVICESRESETREG_DDR_PHY_RST_N_MASK);
>> + __prci_writel(v, PRCI_DEVICESRESETREG_OFFSET, pd);
>> + // HACK to get the '1 full controller clock cycle'.
>
>the same here
Will update in v8.
>
>> + asm volatile ("fence");
>> +
>> + /* These take like 16 cycles to actually propagate. We can't
>> + go sending
>
>nits: wrong multi-line comment format
Will update in v8.
>
>> + * stuff before they come out of reset. So wait. (TODO: Add a register
>> + * to read the current reset states, or DDR Control device?)
>
>Is there no register to reflect the reset states?
As of now, I don't know about this. This is something copied from FSBL.
Right now, we need to go with TODO.
@Troy Benjegerdes Do you have any idea on this ?
>
>> + */
>> + for (int i = 0; i < 256; i++)
>> + asm volatile ("nop");
>> +}
>> +#endif
>> +
>> /*
>> * PRCI integration data for each WRPLL instance
>> */
>> @@ -535,6 +580,9 @@ static struct __prci_wrpll_data
>> __prci_corepll_data = { static struct __prci_wrpll_data __prci_ddrpll_data =
>{
>> .cfg0_offs = PRCI_DDRPLLCFG0_OFFSET,
>> .cfg1_offs = PRCI_DDRPLLCFG1_OFFSET,
>> +#ifdef CONFIG_SPL_BUILD
>> + .release_reset = __prci_ddr_release_reset, #endif
>> };
>>
>> static struct __prci_wrpll_data __prci_gemgxlpll_data = { @@ -556,7
>> +604,7 @@ static struct __prci_clock __prci_init_clocks[] = {
>> [PRCI_CLK_DDRPLL] = {
>> .name = "ddrpll",
>> .parent_name = "hfclk",
>> - .ops = &sifive_fu540_prci_wrpll_ro_clk_ops,
>> + .ops = &sifive_fu540_prci_wrpll_clk_ops,
>> .pwd = &__prci_ddrpll_data,
>> },
>> [PRCI_CLK_GEMGXLPLL] = {
>> @@ -662,6 +710,29 @@ static int sifive_fu540_prci_disable(struct clk *clk)
>> return ret;
>> }
>>
>> +#ifdef CONFIG_SPL_BUILD
>> +static void ethernet_init(struct udevice *dev) {
>> + u32 v;
>> + struct clk clock;
>> + struct __prci_data *pd = dev_get_priv(dev);
>> +
>> + /* GEMGXL init */
>> + clock.id = PRCI_CLK_GEMGXLPLL;
>> + sifive_fu540_prci_set_rate(&clock, 125UL * MHz);
>> + sifive_fu540_prci_clock_enable(&__prci_init_clocks[clock.id],
>> + 1);
>> +
>> + /* Release GEMGXL reset */
>> + v = __prci_readl(pd, PRCI_DEVICESRESETREG_OFFSET);
>> + v |= PRCI_DEVICESRESETREG_GEMGXL_RST_N_MASK;
>> + __prci_writel(v, PRCI_DEVICESRESETREG_OFFSET, pd);
>> +
>> + /* Procmon => core clock */
>> + __prci_writel(PRCI_PROCMONCFG_CORE_CLOCK_MASK,
>PRCI_PROCMONCFG_OFFSET,
>> + pd);
>> +}
>> +#endif
>> +
>> static int sifive_fu540_prci_probe(struct udevice *dev) {
>> int i, err;
>> @@ -687,6 +758,10 @@ static int sifive_fu540_prci_probe(struct udevice
>*dev)
>> __prci_wrpll_read_cfg0(pd, pc->pwd);
>> }
>>
>> +#ifdef CONFIG_SPL_BUILD
>> + ethernet_init(dev);
>> +#endif
>> +
>> return 0;
>> }
>
>Regards,
>Bin
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 21/22] doc: sifive: fu540: Add description for OpenSBI generic platform
2020-05-02 14:30 ` Pragnesh Patel
@ 2020-05-02 15:16 ` Bin Meng
2020-05-02 15:22 ` Pragnesh Patel
0 siblings, 1 reply; 118+ messages in thread
From: Bin Meng @ 2020-05-02 15:16 UTC (permalink / raw)
To: u-boot
Hi Pragnesh,
On Sat, May 2, 2020 at 10:30 PM Pragnesh Patel
<pragnesh.patel@sifive.com> wrote:
>
> Hi Bin,
>
> >-----Original Message-----
> >From: Bin Meng <bmeng.cn@gmail.com>
> >Sent: 02 May 2020 18:26
> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >Cc: U-Boot Mailing List <u-boot@lists.denx.de>; Atish Patra
> ><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Paul
> >Walmsley <paul.walmsley@sifive.com>; Jagan Teki
> ><jagan@amarulasolutions.com>; Troy Benjegerdes
> ><troy.benjegerdes@sifive.com>; Anup Patel <anup.patel@wdc.com>; Sagar
> >Kadam <sagar.kadam@sifive.com>; Rick Chen <rick@andestech.com>
> >Subject: Re: [PATCH v7 21/22] doc: sifive: fu540: Add description for OpenSBI
> >generic platform
> >
> >[External Email] Do not click links or attachments unless you recognize the
> >sender and know the content is safe
> >
> >Hi Pragnesh,
> >
> >On Sat, May 2, 2020 at 6:09 PM Pragnesh Patel <pragnesh.patel@sifive.com>
> >wrote:
> >>
> >> OpenSBI generic platform support provides platform specific
> >> functionality based on the FDT passed by previous booting stage.
> >>
> >> depends on OpenSBI commit:
> >> platform: Add generic FDT based platform support
> >> (sha1: f1aa9e54e00006ae70aeac638d5b75093520f65d)
> >>
> >> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> ---
> >> doc/board/sifive/fu540.rst | 19 +++++++++++++------
> >> 1 file changed, 13 insertions(+), 6 deletions(-)
> >>
> >> diff --git a/doc/board/sifive/fu540.rst b/doc/board/sifive/fu540.rst
> >> index 610ba87074..1c3d4740f3 100644
> >> --- a/doc/board/sifive/fu540.rst
> >> +++ b/doc/board/sifive/fu540.rst
> >> @@ -22,14 +22,21 @@ The support for following drivers are already
> >enabled:
> >>
> >> TODO:
> >>
> >> -1. U-Boot expects the serial console device entry to be present under
> >/chosen
> >> - DT node. Without a serial console U-Boot will panic. Example:
> >> +1. The DTB passed by U-Boot SPL or FSBL to OpenSBI should have CLINT
> >> + DT node and the "/chosen" DT node should have "stdout-path" DT
> >> + property.
> >>
> >> .. code-block:: none
> >>
> >> - chosen {
> >> - stdout-path = "/soc/serial at 10010000:115200";
> >> - };
> >> + chosen {
> >> + stdout-path = "/soc/serial at 10010000:115200";
> >> + };
> >> +
> >> + clint at 2000000 {
> >> + compatible = "riscv,clint0";
> >> + interrupts-extended = <&cpu0_intc 3 &cpu0_intc 7 &cpu1_intc 3
> >&cpu1_intc 7 &cpu2_intc 3 &cpu2_intc 7 &cpu3_intc 3 &cpu3_intc 7
> >&cpu4_intc 3 &cpu4_intc 7>;
> >> + reg = <0x0 0x2000000 0x0 0xc0000>;
> >> + };
> >
> >Can we update the U-Boot dtsi to include the changes?
>
> Can you please clarify which dtsi fu540-c000-u-boot.dtsi or fu540-c000.dtsi ?
>
> I have already added clint DT node in "arch/riscv/dts/fu540-c000-u-boot.dtsi"
I thought we did not add this. So maybe we can remove this information
completely from the doc?
Regards,
Bin
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 21/22] doc: sifive: fu540: Add description for OpenSBI generic platform
2020-05-02 15:16 ` Bin Meng
@ 2020-05-02 15:22 ` Pragnesh Patel
2020-05-02 15:27 ` Bin Meng
0 siblings, 1 reply; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-02 15:22 UTC (permalink / raw)
To: u-boot
Hi Bin,
>-----Original Message-----
>From: Bin Meng <bmeng.cn@gmail.com>
>Sent: 02 May 2020 20:47
>To: Pragnesh Patel <pragnesh.patel@sifive.com>
>Cc: U-Boot Mailing List <u-boot@lists.denx.de>; Atish Patra
><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Paul
>Walmsley <paul.walmsley@sifive.com>; Jagan Teki
><jagan@amarulasolutions.com>; Troy Benjegerdes
><troy.benjegerdes@sifive.com>; Anup Patel <anup.patel@wdc.com>; Sagar
>Kadam <sagar.kadam@sifive.com>; Rick Chen <rick@andestech.com>
>Subject: Re: [PATCH v7 21/22] doc: sifive: fu540: Add description for OpenSBI
>generic platform
>
>[External Email] Do not click links or attachments unless you recognize the
>sender and know the content is safe
>
>Hi Pragnesh,
>
>On Sat, May 2, 2020 at 10:30 PM Pragnesh Patel <pragnesh.patel@sifive.com>
>wrote:
>>
>> Hi Bin,
>>
>> >-----Original Message-----
>> >From: Bin Meng <bmeng.cn@gmail.com>
>> >Sent: 02 May 2020 18:26
>> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
>> >Cc: U-Boot Mailing List <u-boot@lists.denx.de>; Atish Patra
>> ><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>;
>> >Paul Walmsley <paul.walmsley@sifive.com>; Jagan Teki
>> ><jagan@amarulasolutions.com>; Troy Benjegerdes
>> ><troy.benjegerdes@sifive.com>; Anup Patel <anup.patel@wdc.com>; Sagar
>> >Kadam <sagar.kadam@sifive.com>; Rick Chen <rick@andestech.com>
>> >Subject: Re: [PATCH v7 21/22] doc: sifive: fu540: Add description for
>> >OpenSBI generic platform
>> >
>> >[External Email] Do not click links or attachments unless you
>> >recognize the sender and know the content is safe
>> >
>> >Hi Pragnesh,
>> >
>> >On Sat, May 2, 2020 at 6:09 PM Pragnesh Patel
>> ><pragnesh.patel@sifive.com>
>> >wrote:
>> >>
>> >> OpenSBI generic platform support provides platform specific
>> >> functionality based on the FDT passed by previous booting stage.
>> >>
>> >> depends on OpenSBI commit:
>> >> platform: Add generic FDT based platform support
>> >> (sha1: f1aa9e54e00006ae70aeac638d5b75093520f65d)
>> >>
>> >> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
>> >> ---
>> >> doc/board/sifive/fu540.rst | 19 +++++++++++++------
>> >> 1 file changed, 13 insertions(+), 6 deletions(-)
>> >>
>> >> diff --git a/doc/board/sifive/fu540.rst
>> >> b/doc/board/sifive/fu540.rst index 610ba87074..1c3d4740f3 100644
>> >> --- a/doc/board/sifive/fu540.rst
>> >> +++ b/doc/board/sifive/fu540.rst
>> >> @@ -22,14 +22,21 @@ The support for following drivers are already
>> >enabled:
>> >>
>> >> TODO:
>> >>
>> >> -1. U-Boot expects the serial console device entry to be present
>> >> under
>> >/chosen
>> >> - DT node. Without a serial console U-Boot will panic. Example:
>> >> +1. The DTB passed by U-Boot SPL or FSBL to OpenSBI should have CLINT
>> >> + DT node and the "/chosen" DT node should have "stdout-path" DT
>> >> + property.
>> >>
>> >> .. code-block:: none
>> >>
>> >> - chosen {
>> >> - stdout-path = "/soc/serial at 10010000:115200";
>> >> - };
>> >> + chosen {
>> >> + stdout-path = "/soc/serial at 10010000:115200";
>> >> + };
>> >> +
>> >> + clint at 2000000 {
>> >> + compatible = "riscv,clint0";
>> >> + interrupts-extended = <&cpu0_intc 3 &cpu0_intc 7
>> >> + &cpu1_intc 3
>> >&cpu1_intc 7 &cpu2_intc 3 &cpu2_intc 7 &cpu3_intc 3 &cpu3_intc 7
>> >&cpu4_intc 3 &cpu4_intc 7>;
>> >> + reg = <0x0 0x2000000 0x0 0xc0000>;
>> >> + };
>> >
>> >Can we update the U-Boot dtsi to include the changes?
>>
>> Can you please clarify which dtsi fu540-c000-u-boot.dtsi or fu540-c000.dtsi ?
>>
>> I have already added clint DT node in "arch/riscv/dts/fu540-c000-u-
>boot.dtsi"
>
>I thought we did not add this. So maybe we can remove this information
>completely from the doc?
OpenSBI expect a "chosen DT node and clint DT node" from prior stage bootloader DTB, So i think
it's fine to add clint as a reference here.
Any suggestions are welcome.
>
>Regards,
>Bin
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 21/22] doc: sifive: fu540: Add description for OpenSBI generic platform
2020-05-02 15:22 ` Pragnesh Patel
@ 2020-05-02 15:27 ` Bin Meng
2020-05-02 15:29 ` Pragnesh Patel
2020-05-03 4:36 ` Anup Patel
0 siblings, 2 replies; 118+ messages in thread
From: Bin Meng @ 2020-05-02 15:27 UTC (permalink / raw)
To: u-boot
Hi Pragnesh,
On Sat, May 2, 2020 at 11:22 PM Pragnesh Patel
<pragnesh.patel@sifive.com> wrote:
>
>
> Hi Bin,
>
> >-----Original Message-----
> >From: Bin Meng <bmeng.cn@gmail.com>
> >Sent: 02 May 2020 20:47
> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >Cc: U-Boot Mailing List <u-boot@lists.denx.de>; Atish Patra
> ><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Paul
> >Walmsley <paul.walmsley@sifive.com>; Jagan Teki
> ><jagan@amarulasolutions.com>; Troy Benjegerdes
> ><troy.benjegerdes@sifive.com>; Anup Patel <anup.patel@wdc.com>; Sagar
> >Kadam <sagar.kadam@sifive.com>; Rick Chen <rick@andestech.com>
> >Subject: Re: [PATCH v7 21/22] doc: sifive: fu540: Add description for OpenSBI
> >generic platform
> >
> >[External Email] Do not click links or attachments unless you recognize the
> >sender and know the content is safe
> >
> >Hi Pragnesh,
> >
> >On Sat, May 2, 2020 at 10:30 PM Pragnesh Patel <pragnesh.patel@sifive.com>
> >wrote:
> >>
> >> Hi Bin,
> >>
> >> >-----Original Message-----
> >> >From: Bin Meng <bmeng.cn@gmail.com>
> >> >Sent: 02 May 2020 18:26
> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> >Cc: U-Boot Mailing List <u-boot@lists.denx.de>; Atish Patra
> >> ><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>;
> >> >Paul Walmsley <paul.walmsley@sifive.com>; Jagan Teki
> >> ><jagan@amarulasolutions.com>; Troy Benjegerdes
> >> ><troy.benjegerdes@sifive.com>; Anup Patel <anup.patel@wdc.com>; Sagar
> >> >Kadam <sagar.kadam@sifive.com>; Rick Chen <rick@andestech.com>
> >> >Subject: Re: [PATCH v7 21/22] doc: sifive: fu540: Add description for
> >> >OpenSBI generic platform
> >> >
> >> >[External Email] Do not click links or attachments unless you
> >> >recognize the sender and know the content is safe
> >> >
> >> >Hi Pragnesh,
> >> >
> >> >On Sat, May 2, 2020 at 6:09 PM Pragnesh Patel
> >> ><pragnesh.patel@sifive.com>
> >> >wrote:
> >> >>
> >> >> OpenSBI generic platform support provides platform specific
> >> >> functionality based on the FDT passed by previous booting stage.
> >> >>
> >> >> depends on OpenSBI commit:
> >> >> platform: Add generic FDT based platform support
> >> >> (sha1: f1aa9e54e00006ae70aeac638d5b75093520f65d)
> >> >>
> >> >> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> >> ---
> >> >> doc/board/sifive/fu540.rst | 19 +++++++++++++------
> >> >> 1 file changed, 13 insertions(+), 6 deletions(-)
> >> >>
> >> >> diff --git a/doc/board/sifive/fu540.rst
> >> >> b/doc/board/sifive/fu540.rst index 610ba87074..1c3d4740f3 100644
> >> >> --- a/doc/board/sifive/fu540.rst
> >> >> +++ b/doc/board/sifive/fu540.rst
> >> >> @@ -22,14 +22,21 @@ The support for following drivers are already
> >> >enabled:
> >> >>
> >> >> TODO:
> >> >>
> >> >> -1. U-Boot expects the serial console device entry to be present
> >> >> under
> >> >/chosen
> >> >> - DT node. Without a serial console U-Boot will panic. Example:
> >> >> +1. The DTB passed by U-Boot SPL or FSBL to OpenSBI should have CLINT
> >> >> + DT node and the "/chosen" DT node should have "stdout-path" DT
> >> >> + property.
> >> >>
> >> >> .. code-block:: none
> >> >>
> >> >> - chosen {
> >> >> - stdout-path = "/soc/serial at 10010000:115200";
> >> >> - };
> >> >> + chosen {
> >> >> + stdout-path = "/soc/serial at 10010000:115200";
> >> >> + };
> >> >> +
> >> >> + clint at 2000000 {
> >> >> + compatible = "riscv,clint0";
> >> >> + interrupts-extended = <&cpu0_intc 3 &cpu0_intc 7
> >> >> + &cpu1_intc 3
> >> >&cpu1_intc 7 &cpu2_intc 3 &cpu2_intc 7 &cpu3_intc 3 &cpu3_intc 7
> >> >&cpu4_intc 3 &cpu4_intc 7>;
> >> >> + reg = <0x0 0x2000000 0x0 0xc0000>;
> >> >> + };
> >> >
> >> >Can we update the U-Boot dtsi to include the changes?
> >>
> >> Can you please clarify which dtsi fu540-c000-u-boot.dtsi or fu540-c000.dtsi ?
> >>
> >> I have already added clint DT node in "arch/riscv/dts/fu540-c000-u-
> >boot.dtsi"
> >
> >I thought we did not add this. So maybe we can remove this information
> >completely from the doc?
>
> OpenSBI expect a "chosen DT node and clint DT node" from prior stage bootloader DTB, So i think
> it's fine to add clint as a reference here.
>
> Any suggestions are welcome.
>
Maybe such information should be put in the OpenSBI generic platform
doc, but not U-Boot doc ??
Regards,
Bin
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 21/22] doc: sifive: fu540: Add description for OpenSBI generic platform
2020-05-02 15:27 ` Bin Meng
@ 2020-05-02 15:29 ` Pragnesh Patel
2020-05-03 4:36 ` Anup Patel
1 sibling, 0 replies; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-02 15:29 UTC (permalink / raw)
To: u-boot
Hi Bin,
>-----Original Message-----
>From: Bin Meng <bmeng.cn@gmail.com>
>Sent: 02 May 2020 20:58
>To: Pragnesh Patel <pragnesh.patel@sifive.com>
>Cc: U-Boot Mailing List <u-boot@lists.denx.de>; Atish Patra
><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Paul
>Walmsley <paul.walmsley@sifive.com>; Jagan Teki
><jagan@amarulasolutions.com>; Troy Benjegerdes
><troy.benjegerdes@sifive.com>; Anup Patel <anup.patel@wdc.com>; Sagar
>Kadam <sagar.kadam@sifive.com>; Rick Chen <rick@andestech.com>
>Subject: Re: [PATCH v7 21/22] doc: sifive: fu540: Add description for OpenSBI
>generic platform
>
>[External Email] Do not click links or attachments unless you recognize the
>sender and know the content is safe
>
>Hi Pragnesh,
>
>On Sat, May 2, 2020 at 11:22 PM Pragnesh Patel <pragnesh.patel@sifive.com>
>wrote:
>>
>>
>> Hi Bin,
>>
>> >-----Original Message-----
>> >From: Bin Meng <bmeng.cn@gmail.com>
>> >Sent: 02 May 2020 20:47
>> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
>> >Cc: U-Boot Mailing List <u-boot@lists.denx.de>; Atish Patra
>> ><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>;
>> >Paul Walmsley <paul.walmsley@sifive.com>; Jagan Teki
>> ><jagan@amarulasolutions.com>; Troy Benjegerdes
>> ><troy.benjegerdes@sifive.com>; Anup Patel <anup.patel@wdc.com>; Sagar
>> >Kadam <sagar.kadam@sifive.com>; Rick Chen <rick@andestech.com>
>> >Subject: Re: [PATCH v7 21/22] doc: sifive: fu540: Add description for
>> >OpenSBI generic platform
>> >
>> >[External Email] Do not click links or attachments unless you
>> >recognize the sender and know the content is safe
>> >
>> >Hi Pragnesh,
>> >
>> >On Sat, May 2, 2020 at 10:30 PM Pragnesh Patel
>> ><pragnesh.patel@sifive.com>
>> >wrote:
>> >>
>> >> Hi Bin,
>> >>
>> >> >-----Original Message-----
>> >> >From: Bin Meng <bmeng.cn@gmail.com>
>> >> >Sent: 02 May 2020 18:26
>> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
>> >> >Cc: U-Boot Mailing List <u-boot@lists.denx.de>; Atish Patra
>> >> ><atish.patra@wdc.com>; Palmer Dabbelt
><palmerdabbelt@google.com>;
>> >> >Paul Walmsley <paul.walmsley@sifive.com>; Jagan Teki
>> >> ><jagan@amarulasolutions.com>; Troy Benjegerdes
>> >> ><troy.benjegerdes@sifive.com>; Anup Patel <anup.patel@wdc.com>;
>> >> >Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
>> >> ><rick@andestech.com>
>> >> >Subject: Re: [PATCH v7 21/22] doc: sifive: fu540: Add description
>> >> >for OpenSBI generic platform
>> >> >
>> >> >[External Email] Do not click links or attachments unless you
>> >> >recognize the sender and know the content is safe
>> >> >
>> >> >Hi Pragnesh,
>> >> >
>> >> >On Sat, May 2, 2020 at 6:09 PM Pragnesh Patel
>> >> ><pragnesh.patel@sifive.com>
>> >> >wrote:
>> >> >>
>> >> >> OpenSBI generic platform support provides platform specific
>> >> >> functionality based on the FDT passed by previous booting stage.
>> >> >>
>> >> >> depends on OpenSBI commit:
>> >> >> platform: Add generic FDT based platform support
>> >> >> (sha1: f1aa9e54e00006ae70aeac638d5b75093520f65d)
>> >> >>
>> >> >> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
>> >> >> ---
>> >> >> doc/board/sifive/fu540.rst | 19 +++++++++++++------
>> >> >> 1 file changed, 13 insertions(+), 6 deletions(-)
>> >> >>
>> >> >> diff --git a/doc/board/sifive/fu540.rst
>> >> >> b/doc/board/sifive/fu540.rst index 610ba87074..1c3d4740f3 100644
>> >> >> --- a/doc/board/sifive/fu540.rst
>> >> >> +++ b/doc/board/sifive/fu540.rst
>> >> >> @@ -22,14 +22,21 @@ The support for following drivers are
>> >> >> already
>> >> >enabled:
>> >> >>
>> >> >> TODO:
>> >> >>
>> >> >> -1. U-Boot expects the serial console device entry to be present
>> >> >> under
>> >> >/chosen
>> >> >> - DT node. Without a serial console U-Boot will panic. Example:
>> >> >> +1. The DTB passed by U-Boot SPL or FSBL to OpenSBI should have
>CLINT
>> >> >> + DT node and the "/chosen" DT node should have "stdout-path" DT
>> >> >> + property.
>> >> >>
>> >> >> .. code-block:: none
>> >> >>
>> >> >> - chosen {
>> >> >> - stdout-path = "/soc/serial at 10010000:115200";
>> >> >> - };
>> >> >> + chosen {
>> >> >> + stdout-path = "/soc/serial at 10010000:115200";
>> >> >> + };
>> >> >> +
>> >> >> + clint at 2000000 {
>> >> >> + compatible = "riscv,clint0";
>> >> >> + interrupts-extended = <&cpu0_intc 3 &cpu0_intc 7
>> >> >> + &cpu1_intc 3
>> >> >&cpu1_intc 7 &cpu2_intc 3 &cpu2_intc 7 &cpu3_intc 3 &cpu3_intc 7
>> >> >&cpu4_intc 3 &cpu4_intc 7>;
>> >> >> + reg = <0x0 0x2000000 0x0 0xc0000>;
>> >> >> + };
>> >> >
>> >> >Can we update the U-Boot dtsi to include the changes?
>> >>
>> >> Can you please clarify which dtsi fu540-c000-u-boot.dtsi or fu540-
>c000.dtsi ?
>> >>
>> >> I have already added clint DT node in "arch/riscv/dts/fu540-c000-u-
>> >boot.dtsi"
>> >
>> >I thought we did not add this. So maybe we can remove this
>> >information completely from the doc?
>>
>> OpenSBI expect a "chosen DT node and clint DT node" from prior stage
>> bootloader DTB, So i think it's fine to add clint as a reference here.
>>
>> Any suggestions are welcome.
>>
>
>Maybe such information should be put in the OpenSBI generic platform doc,
>but not U-Boot doc ??
I am okay with your suggestion, will remove clint in v8.
>
>Regards,
>Bin
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 04/22] lib: Makefile: build crc7.c when CONFIG_MMC_SPI
2020-05-02 12:58 ` Heinrich Schuchardt
@ 2020-05-02 15:33 ` Jagan Teki
2020-05-04 5:45 ` Pragnesh Patel
2020-05-03 9:54 ` Pragnesh Patel
1 sibling, 1 reply; 118+ messages in thread
From: Jagan Teki @ 2020-05-02 15:33 UTC (permalink / raw)
To: u-boot
On Sat, May 2, 2020 at 6:45 PM Heinrich Schuchardt <xypron.glpk@gmx.de> wrote:
>
> Am May 2, 2020 11:47:10 AM UTC schrieb Bin Meng <bmeng.cn@gmail.com>:
> >Hi Heinrich,
> >
> >On Sat, May 2, 2020 at 6:30 PM Heinrich Schuchardt <xypron.glpk@gmx.de>
> >wrote:
> >>
> >> On 5/2/20 12:06 PM, Pragnesh Patel wrote:
> >> > When build U-Boot SPL, meet an issue of undefined reference to
> >> > 'crc7' for drivers/mmc/mmc_spi.c, so let's compile crc7.c when
> >> > CONFIG_MMC_SPI selected.
> >> >
> >> > Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> > Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
> >> > Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
> >> > ---
> >> > common/spl/Kconfig | 6 ++++++
> >> > drivers/mmc/Kconfig | 1 +
> >> > lib/Makefile | 1 +
> >> > 3 files changed, 8 insertions(+)
> >> >
> >> > diff --git a/common/spl/Kconfig b/common/spl/Kconfig
> >> > index ef5bf66696..d1f0e6bc4c 100644
> >> > --- a/common/spl/Kconfig
> >> > +++ b/common/spl/Kconfig
> >> > @@ -401,6 +401,12 @@ config SPL_CRC32_SUPPORT
> >> > for detected accidental image corruption. For secure
> >applications you
> >> > should consider SHA1 or SHA256.
> >> >
> >> > +config SPL_CRC7_SUPPORT
> >> > + bool "Support CRC7"
> >> > + help
> >> > + Enable CRC7 hashing for drivers which are using in SPL.
> >> > + This is a 32-bit checksum value that can be used to verify
> >images.
> >> > +
> >> > config SPL_MD5_SUPPORT
> >> > bool "Support MD5"
> >> > depends on SPL_FIT
> >> > diff --git a/drivers/mmc/Kconfig b/drivers/mmc/Kconfig
> >> > index 8f0df568b9..139599072a 100644
> >> > --- a/drivers/mmc/Kconfig
> >> > +++ b/drivers/mmc/Kconfig
> >> > @@ -49,6 +49,7 @@ if MMC
> >> > config MMC_SPI
> >> > bool "Support for SPI-based MMC controller"
> >> > depends on DM_MMC && DM_SPI
> >> > + select SPL_CRC7_SUPPORT if SPL
> >> > help
> >> > This selects SPI-based MMC controllers.
> >> > If you have an MMC controller on a SPI bus, say Y here.
> >> > diff --git a/lib/Makefile b/lib/Makefile
> >> > index c6f862b0c2..fcd934857f 100644
> >> > --- a/lib/Makefile
> >> > +++ b/lib/Makefile
> >> > @@ -80,6 +80,7 @@ endif
> >> >
> >> > ifdef CONFIG_SPL_BUILD
> >> > obj-$(CONFIG_SPL_YMODEM_SUPPORT) += crc16.o
> >> > +obj-$(CONFIG_SPL_CRC7_SUPPORT) += crc7.o
> >>
> >> crc7.o is not needed in main U-Boot if MMC_SPI is not selected.
> >>
> >> So instead of adding a new configuration variable simply correct the
> >> existing line in lib/Makefile
> >>
> >> -obj-y += crc7.o
> >> +obj-$(CONFIG_MMC_SPI) += crc7.o
> >
> >This looks incorrect to me. CRC7 can be useful for other drivers too.
> >It should not depend on CONFIG_MMC_SPI.
>
> Using this argument you would always compile everything. Compiling files that are not used is simply a waste of CPU time.
>
> Following your argument. you could also always compile crc7.c for SPL and hope the compiler will eliminate it.
>
> Either way we do not need a new config symbol.
This is one of the reasons I just suggested that the mark 'depends on
MMC_SPI' at the very initial patch.
Marking config SPL_CRC7_SUPPORT which depends on MMC_SPI would work for me.
Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 01/22] misc: add driver for the SiFive otp controller
2020-05-02 10:06 ` [PATCH v7 01/22] misc: add driver for the SiFive otp controller Pragnesh Patel
2020-05-02 12:28 ` Bin Meng
@ 2020-05-02 15:37 ` Jagan Teki
2020-05-02 15:42 ` Pragnesh Patel
1 sibling, 1 reply; 118+ messages in thread
From: Jagan Teki @ 2020-05-02 15:37 UTC (permalink / raw)
To: u-boot
On Sat, May 2, 2020 at 3:37 PM Pragnesh Patel <pragnesh.patel@sifive.com> wrote:
>
> Added a misc driver to handle OTP memory in SiFive SoCs.
>
> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
> ---
> drivers/misc/Kconfig | 7 +
> drivers/misc/Makefile | 1 +
> drivers/misc/sifive-otp.c | 273 ++++++++++++++++++++++++++++++++++++++
> 3 files changed, 281 insertions(+)
> create mode 100644 drivers/misc/sifive-otp.c
>
> diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig
> index 766402745d..03464f1010 100644
> --- a/drivers/misc/Kconfig
> +++ b/drivers/misc/Kconfig
> @@ -68,6 +68,13 @@ config ROCKCHIP_OTP
> addressing and a length or through child-nodes that are generated
> based on the e-fuse map retrieved from the DTS.
>
> +config SIFIVE_OTP
> + bool "SiFive eMemory OTP driver"
> + depends on RISCV && MISC
This can be something like this.
config SIFIVE_OTP
bool "SiFive eMemory OTP driver"
depends on SIFIVE_FU540
select MISC
Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 01/22] misc: add driver for the SiFive otp controller
2020-05-02 15:37 ` Jagan Teki
@ 2020-05-02 15:42 ` Pragnesh Patel
2020-05-02 15:50 ` Jagan Teki
0 siblings, 1 reply; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-02 15:42 UTC (permalink / raw)
To: u-boot
Hi Jagan,
>-----Original Message-----
>From: Jagan Teki <jagan@amarulasolutions.com>
>Sent: 02 May 2020 21:07
>To: Pragnesh Patel <pragnesh.patel@sifive.com>
>Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Bin
>Meng <bmeng.cn@gmail.com>; Paul Walmsley <paul.walmsley@sifive.com>;
>Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
><rick@andestech.com>; Tero Kristo <t-kristo@ti.com>; Simon Glass
><sjg@chromium.org>; Adam Ford <aford173@gmail.com>; Eugen Hristev
><eugen.hristev@microchip.com>; Peng Fan <peng.fan@nxp.com>; Finley Xiao
><finley.xiao@rock-chips.com>; Kever Yang <kever.yang@rock-chips.com>
>Subject: Re: [PATCH v7 01/22] misc: add driver for the SiFive otp controller
>
>[External Email] Do not click links or attachments unless you recognize the
>sender and know the content is safe
>
>On Sat, May 2, 2020 at 3:37 PM Pragnesh Patel <pragnesh.patel@sifive.com>
>wrote:
>>
>> Added a misc driver to handle OTP memory in SiFive SoCs.
>>
>> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
>> ---
>> drivers/misc/Kconfig | 7 +
>> drivers/misc/Makefile | 1 +
>> drivers/misc/sifive-otp.c | 273
>> ++++++++++++++++++++++++++++++++++++++
>> 3 files changed, 281 insertions(+)
>> create mode 100644 drivers/misc/sifive-otp.c
>>
>> diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig index
>> 766402745d..03464f1010 100644
>> --- a/drivers/misc/Kconfig
>> +++ b/drivers/misc/Kconfig
>> @@ -68,6 +68,13 @@ config ROCKCHIP_OTP
>> addressing and a length or through child-nodes that are generated
>> based on the e-fuse map retrieved from the DTS.
>>
>> +config SIFIVE_OTP
>> + bool "SiFive eMemory OTP driver"
>> + depends on RISCV && MISC
>
>This can be something like this.
>
>config SIFIVE_OTP
> bool "SiFive eMemory OTP driver"
> depends on SIFIVE_FU540
This config option is not FU540 specific but it's for all SiFive SoCs.
> select MISC
>
>Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 01/22] misc: add driver for the SiFive otp controller
2020-05-02 15:42 ` Pragnesh Patel
@ 2020-05-02 15:50 ` Jagan Teki
2020-05-02 16:18 ` Pragnesh Patel
0 siblings, 1 reply; 118+ messages in thread
From: Jagan Teki @ 2020-05-02 15:50 UTC (permalink / raw)
To: u-boot
On Sat, May 2, 2020 at 9:12 PM Pragnesh Patel <pragnesh.patel@sifive.com> wrote:
>
> Hi Jagan,
>
> >-----Original Message-----
> >From: Jagan Teki <jagan@amarulasolutions.com>
> >Sent: 02 May 2020 21:07
> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> ><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Bin
> >Meng <bmeng.cn@gmail.com>; Paul Walmsley <paul.walmsley@sifive.com>;
> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
> ><rick@andestech.com>; Tero Kristo <t-kristo@ti.com>; Simon Glass
> ><sjg@chromium.org>; Adam Ford <aford173@gmail.com>; Eugen Hristev
> ><eugen.hristev@microchip.com>; Peng Fan <peng.fan@nxp.com>; Finley Xiao
> ><finley.xiao@rock-chips.com>; Kever Yang <kever.yang@rock-chips.com>
> >Subject: Re: [PATCH v7 01/22] misc: add driver for the SiFive otp controller
> >
> >[External Email] Do not click links or attachments unless you recognize the
> >sender and know the content is safe
> >
> >On Sat, May 2, 2020 at 3:37 PM Pragnesh Patel <pragnesh.patel@sifive.com>
> >wrote:
> >>
> >> Added a misc driver to handle OTP memory in SiFive SoCs.
> >>
> >> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> ---
> >> drivers/misc/Kconfig | 7 +
> >> drivers/misc/Makefile | 1 +
> >> drivers/misc/sifive-otp.c | 273
> >> ++++++++++++++++++++++++++++++++++++++
> >> 3 files changed, 281 insertions(+)
> >> create mode 100644 drivers/misc/sifive-otp.c
> >>
> >> diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig index
> >> 766402745d..03464f1010 100644
> >> --- a/drivers/misc/Kconfig
> >> +++ b/drivers/misc/Kconfig
> >> @@ -68,6 +68,13 @@ config ROCKCHIP_OTP
> >> addressing and a length or through child-nodes that are generated
> >> based on the e-fuse map retrieved from the DTS.
> >>
> >> +config SIFIVE_OTP
> >> + bool "SiFive eMemory OTP driver"
> >> + depends on RISCV && MISC
> >
> >This can be something like this.
> >
> >config SIFIVE_OTP
> > bool "SiFive eMemory OTP driver"
> > depends on SIFIVE_FU540
>
> This config option is not FU540 specific but it's for all SiFive SoCs.
Well RISCV is not SIFIVE, better add SIFIVE_FU540 as of now if you
have more SoC's in future will update by adding one more or add new
symbol SIFIVE.
Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 06/22] sifive: fu540: add ddr driver
2020-05-02 10:06 ` [PATCH v7 06/22] sifive: fu540: add ddr driver Pragnesh Patel
2020-05-02 12:28 ` Bin Meng
@ 2020-05-02 15:59 ` Jagan Teki
2020-05-02 16:32 ` Pragnesh Patel
1 sibling, 1 reply; 118+ messages in thread
From: Jagan Teki @ 2020-05-02 15:59 UTC (permalink / raw)
To: u-boot
On Sat, May 2, 2020 at 3:37 PM Pragnesh Patel <pragnesh.patel@sifive.com> wrote:
>
> Add driver for fu540 to support ddr initialization in SPL.
> This driver is based on FSBL
> (https://github.com/sifive/freedom-u540-c000-bootloader.git)
>
> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
> ---
> board/sifive/fu540/Kconfig | 2 +
> drivers/ram/Kconfig | 1 +
> drivers/ram/Makefile | 2 +
> drivers/ram/sifive/Kconfig | 13 +
> drivers/ram/sifive/Makefile | 6 +
> drivers/ram/sifive/sdram_fu540.c | 416 +++++++++++++++++++++++++++++++
> 6 files changed, 440 insertions(+)
> create mode 100644 drivers/ram/sifive/Kconfig
> create mode 100644 drivers/ram/sifive/Makefile
> create mode 100644 drivers/ram/sifive/sdram_fu540.c
>
> diff --git a/board/sifive/fu540/Kconfig b/board/sifive/fu540/Kconfig
> index 4330ac4491..d41c305227 100644
> --- a/board/sifive/fu540/Kconfig
> +++ b/board/sifive/fu540/Kconfig
> @@ -19,6 +19,8 @@ config SYS_TEXT_BASE
> config BOARD_SPECIFIC_OPTIONS # dummy
> def_bool y
> select GENERIC_RISCV
> + select RAM
> + select SPL_RAM if SPL
> imply CMD_DHCP
> imply CMD_EXT2
> imply CMD_EXT4
> diff --git a/drivers/ram/Kconfig b/drivers/ram/Kconfig
> index 56fea7c94c..66074d1feb 100644
> --- a/drivers/ram/Kconfig
> +++ b/drivers/ram/Kconfig
> @@ -75,3 +75,4 @@ config IMXRT_SDRAM
>
> source "drivers/ram/rockchip/Kconfig"
> source "drivers/ram/stm32mp1/Kconfig"
> +source "drivers/ram/sifive/Kconfig"
> diff --git a/drivers/ram/Makefile b/drivers/ram/Makefile
> index 5c897410c6..769c9d6218 100644
> --- a/drivers/ram/Makefile
> +++ b/drivers/ram/Makefile
> @@ -17,3 +17,5 @@ obj-$(CONFIG_ARCH_MEDIATEK) += mediatek/
> obj-$(CONFIG_K3_J721E_DDRSS) += k3-j721e/
>
> obj-$(CONFIG_IMXRT_SDRAM) += imxrt_sdram.o
> +
> +obj-$(CONFIG_RAM_SIFIVE) += sifive/
> diff --git a/drivers/ram/sifive/Kconfig b/drivers/ram/sifive/Kconfig
> new file mode 100644
> index 0000000000..6aca22ab2a
> --- /dev/null
> +++ b/drivers/ram/sifive/Kconfig
> @@ -0,0 +1,13 @@
> +config RAM_SIFIVE
> + bool "Ram drivers support for SiFive SoCs"
> + depends on RAM && RISCV
> + default y
> + help
> + This enables support for ram drivers of SiFive SoCs.
> +
> +config SIFIVE_FU540_DDR
> + bool "SiFive FU540 DDR driver"
> + depends on RAM_SIFIVE
> + default y if TARGET_SIFIVE_FU540
> + help
> + This enables DDR support for the platforms based on SiFive FU540 SoC.
> diff --git a/drivers/ram/sifive/Makefile b/drivers/ram/sifive/Makefile
> new file mode 100644
> index 0000000000..0187805199
> --- /dev/null
> +++ b/drivers/ram/sifive/Makefile
> @@ -0,0 +1,6 @@
> +# SPDX-License-Identifier: GPL-2.0+
> +#
> +# Copyright (c) 2020 SiFive, Inc
> +#
> +
> +obj-$(CONFIG_SIFIVE_FU540_DDR) += sdram_fu540.o
> diff --git a/drivers/ram/sifive/sdram_fu540.c b/drivers/ram/sifive/sdram_fu540.c
> new file mode 100644
> index 0000000000..0aa2b2b44a
> --- /dev/null
> +++ b/drivers/ram/sifive/sdram_fu540.c
> @@ -0,0 +1,416 @@
> +// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
> +/*
> + * (C) Copyright 2020 SiFive, Inc.
> + *
> + * Authors:
> + * Pragnesh Patel <pragnesh.patel@sifive.com>
> + */
> +
> +#include <common.h>
> +#include <dm.h>
> +#include <init.h>
> +#include <ram.h>
> +#include <regmap.h>
> +#include <syscon.h>
> +#include <asm/io.h>
> +#include <clk.h>
> +
> +#define DENALI_CTL_0 0
> +#define DENALI_CTL_21 21
> +#define DENALI_CTL_120 120
> +#define DENALI_CTL_132 132
> +#define DENALI_CTL_136 136
> +#define DENALI_CTL_170 170
> +#define DENALI_CTL_181 181
> +#define DENALI_CTL_182 182
> +#define DENALI_CTL_184 184
> +#define DENALI_CTL_208 208
> +#define DENALI_CTL_209 209
> +#define DENALI_CTL_210 210
> +#define DENALI_CTL_212 212
> +#define DENALI_CTL_214 214
> +#define DENALI_CTL_216 216
> +#define DENALI_CTL_224 224
> +#define DENALI_CTL_225 225
> +#define DENALI_CTL_260 260
> +
> +#define DENALI_PHY_1152 1152
> +#define DENALI_PHY_1214 1214
> +
> +#define PAYLOAD_DEST 0x80000000
> +#define DDR_MEM_SIZE (8UL * 1024UL * 1024UL * 1024UL)
> +
> +#define DRAM_CLASS_OFFSET 8
> +#define DRAM_CLASS_DDR4 0xA
> +#define OPTIMAL_RMODW_EN_OFFSET 0
> +#define DISABLE_RD_INTERLEAVE_OFFSET 16
> +#define OUT_OF_RANGE_OFFSET 1
> +#define MULTIPLE_OUT_OF_RANGE_OFFSET 2
> +#define PORT_COMMAND_CHANNEL_ERROR_OFFSET 7
> +#define MC_INIT_COMPLETE_OFFSET 8
> +#define LEVELING_OPERATION_COMPLETED_OFFSET 22
> +#define DFI_PHY_WRLELV_MODE_OFFSET 24
> +#define DFI_PHY_RDLVL_MODE_OFFSET 24
> +#define DFI_PHY_RDLVL_GATE_MODE_OFFSET 0
> +#define VREF_EN_OFFSET 24
> +#define PORT_ADDR_PROTECTION_EN_OFFSET 0
> +#define AXI0_ADDRESS_RANGE_ENABLE 8
> +#define AXI0_RANGE_PROT_BITS_0_OFFSET 24
> +#define RDLVL_EN_OFFSET 16
> +#define RDLVL_GATE_EN_OFFSET 24
> +#define WRLVL_EN_OFFSET 0
> +
> +#define PHY_RX_CAL_DQ0_0_OFFSET 0
> +#define PHY_RX_CAL_DQ1_0_OFFSET 16
> +
> +struct fu540_ddrctl {
> + volatile u32 denali_ctl[265];
> +};
> +
> +struct fu540_ddrphy {
> + volatile u32 denali_phy[1215];
> +};
> +
> +/**
> + * struct ddr_info
> + *
> + * @dev : pointer for the device
> + * @info : UCLASS RAM information
> + * @ctl : DDR controller base address
> + * @phy : DDR PHY base address
> + * @ctrl : DDR control base address
> + * @physical_filter_ctrl : DDR physical filter control base address
> + */
> +struct ddr_info {
> + struct udevice *dev;
> + struct ram_info info;
> + struct fu540_ddrctl *ctl;
> + struct fu540_ddrphy *phy;
> + struct clk ddr_clk;
> + u32 *physical_filter_ctrl;
> +};
> +
> +#if defined(CONFIG_TPL_BUILD) || \
> + (!defined(CONFIG_TPL) && defined(CONFIG_SPL_BUILD))
> +
> +struct fu540_sdram_params {
> + struct fu540_ddrctl pctl_regs;
> + struct fu540_ddrphy phy_regs;
> +};
> +
> +struct sifive_dmc_plat {
> +#if CONFIG_IS_ENABLED(OF_PLATDATA)
> + struct dtd_sifive_fu540_dmc dtplat;
> +#else
> + struct fu540_sdram_params sdram_params;
> +#endif
> +};
> +
> +/* n: Unit bytes */
Please add TODO "It can be possible to use common copy_to_reg API"
> +static void sdram_copy_to_reg(volatile u32 *dest,
> + volatile u32 *src, u32 n)
> +{
> + int i;
> +
> + for (i = 0; i < n / sizeof(u32); i++) {
> + writel(*src, dest);
> + src++;
> + dest++;
> + }
> +}
> +
> +static void ddr_setuprangeprotection(volatile u32 *ctl, u64 end_addr)
> +{
> + u32 end_addr_16kblocks = ((end_addr >> 14) & 0x7FFFFF) - 1;
> +
> + writel(0x0, DENALI_CTL_209 + ctl);
> + writel(end_addr_16kblocks, DENALI_CTL_210 + ctl);
> + writel(0x0, DENALI_CTL_212 + ctl);
> + writel(0x0, DENALI_CTL_214 + ctl);
> + writel(0x0, DENALI_CTL_216 + ctl);
> + setbits_le32(DENALI_CTL_224 + ctl,
> + 0x3 << AXI0_RANGE_PROT_BITS_0_OFFSET);
> + writel(0xFFFFFFFF, DENALI_CTL_225 + ctl);
> + setbits_le32(DENALI_CTL_208 + ctl, 0x1 << AXI0_ADDRESS_RANGE_ENABLE);
> + setbits_le32(DENALI_CTL_208 + ctl,
> + 0x1 << PORT_ADDR_PROTECTION_EN_OFFSET);
> +}
> +
> +static void ddr_start(volatile u32 *ctl, u32 *physical_filter_ctrl, u64 ddr_end)
> +{
> + int val;
> +
> + volatile u64 *filterreg = (volatile u64 *)physical_filter_ctrl;
> +
> + setbits_le32(DENALI_CTL_0 + ctl, 0x1);
> +
> + do {
> + val = readl(DENALI_CTL_132 + ctl) &
> + (1 << MC_INIT_COMPLETE_OFFSET);
> + } while (val == 0);
wait_for_bit_le32(DENALI_CTL_132 + ctl, BIT(MC_INIT_COMPLETE_OFFSET),
true, 100, false);
otherwise,
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 10/22] clk: sifive: fu540-prci: ddr and ethernet clock initialization in SPL
2020-05-02 10:06 ` [PATCH v7 10/22] clk: sifive: fu540-prci: ddr and ethernet clock initialization in SPL Pragnesh Patel
2020-05-02 12:28 ` Bin Meng
@ 2020-05-02 16:14 ` Jagan Teki
2020-05-02 16:35 ` Pragnesh Patel
1 sibling, 1 reply; 118+ messages in thread
From: Jagan Teki @ 2020-05-02 16:14 UTC (permalink / raw)
To: u-boot
On Sat, May 2, 2020 at 3:38 PM Pragnesh Patel <pragnesh.patel@sifive.com> wrote:
>
> Add ddr clock release reset and ehternet clock initialization for
> SPL
Why ethernet still require for SPL?
Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 01/22] misc: add driver for the SiFive otp controller
2020-05-02 15:50 ` Jagan Teki
@ 2020-05-02 16:18 ` Pragnesh Patel
2020-05-10 9:04 ` Jagan Teki
0 siblings, 1 reply; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-02 16:18 UTC (permalink / raw)
To: u-boot
Hi Jagan,
>-----Original Message-----
>From: Jagan Teki <jagan@amarulasolutions.com>
>Sent: 02 May 2020 21:21
>To: Pragnesh Patel <pragnesh.patel@sifive.com>
>Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Bin
>Meng <bmeng.cn@gmail.com>; Paul Walmsley <paul.walmsley@sifive.com>;
>Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
><rick@andestech.com>; Tero Kristo <t-kristo@ti.com>; Simon Glass
><sjg@chromium.org>; Adam Ford <aford173@gmail.com>; Eugen Hristev
><eugen.hristev@microchip.com>; Peng Fan <peng.fan@nxp.com>; Finley Xiao
><finley.xiao@rock-chips.com>; Kever Yang <kever.yang@rock-chips.com>
>Subject: Re: [PATCH v7 01/22] misc: add driver for the SiFive otp controller
>
>[External Email] Do not click links or attachments unless you recognize the
>sender and know the content is safe
>
>On Sat, May 2, 2020 at 9:12 PM Pragnesh Patel <pragnesh.patel@sifive.com>
>wrote:
>>
>> Hi Jagan,
>>
>> >-----Original Message-----
>> >From: Jagan Teki <jagan@amarulasolutions.com>
>> >Sent: 02 May 2020 21:07
>> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
>> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
>> ><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>;
>Bin
>> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
><paul.walmsley@sifive.com>;
>> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
>> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick
>Chen
>> ><rick@andestech.com>; Tero Kristo <t-kristo@ti.com>; Simon Glass
>> ><sjg@chromium.org>; Adam Ford <aford173@gmail.com>; Eugen Hristev
>> ><eugen.hristev@microchip.com>; Peng Fan <peng.fan@nxp.com>; Finley
>> >Xiao <finley.xiao@rock-chips.com>; Kever Yang
>> ><kever.yang@rock-chips.com>
>> >Subject: Re: [PATCH v7 01/22] misc: add driver for the SiFive otp
>> >controller
>> >
>> >[External Email] Do not click links or attachments unless you
>> >recognize the sender and know the content is safe
>> >
>> >On Sat, May 2, 2020 at 3:37 PM Pragnesh Patel
>> ><pragnesh.patel@sifive.com>
>> >wrote:
>> >>
>> >> Added a misc driver to handle OTP memory in SiFive SoCs.
>> >>
>> >> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
>> >> ---
>> >> drivers/misc/Kconfig | 7 +
>> >> drivers/misc/Makefile | 1 +
>> >> drivers/misc/sifive-otp.c | 273
>> >> ++++++++++++++++++++++++++++++++++++++
>> >> 3 files changed, 281 insertions(+) create mode 100644
>> >> drivers/misc/sifive-otp.c
>> >>
>> >> diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig index
>> >> 766402745d..03464f1010 100644
>> >> --- a/drivers/misc/Kconfig
>> >> +++ b/drivers/misc/Kconfig
>> >> @@ -68,6 +68,13 @@ config ROCKCHIP_OTP
>> >> addressing and a length or through child-nodes that are generated
>> >> based on the e-fuse map retrieved from the DTS.
>> >>
>> >> +config SIFIVE_OTP
>> >> + bool "SiFive eMemory OTP driver"
>> >> + depends on RISCV && MISC
>> >
>> >This can be something like this.
>> >
>> >config SIFIVE_OTP
>> > bool "SiFive eMemory OTP driver"
>> > depends on SIFIVE_FU540
>>
>> This config option is not FU540 specific but it's for all SiFive SoCs.
>
>Well RISCV is not SIFIVE, better add SIFIVE_FU540 as of now if you have more
>SoC's in future will update by adding one more or add new symbol SIFIVE.
IMHO it's better not to make it SoC specific, Board Kconfig file will imply this option if needed.
This is something we follow for FU540.
SIFIVE_OTP is depends on SIFIVE SoCs and all SIFIVE SoCs are RISCV specific that's why I added
depends on RISCV.
>
>Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
2020-05-02 10:06 ` [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot Pragnesh Patel
@ 2020-05-02 16:18 ` Jagan Teki
2020-05-02 16:42 ` Pragnesh Patel
0 siblings, 1 reply; 118+ messages in thread
From: Jagan Teki @ 2020-05-02 16:18 UTC (permalink / raw)
To: u-boot
On Sat, May 2, 2020 at 3:39 PM Pragnesh Patel <pragnesh.patel@sifive.com> wrote:
>
> Add L2 cache node to enable cache ways from U-Boot
This and 20/22 doesn't relate to SPL MMC boot?, if yes please send
them separately.
Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 22/22] doc: sifive: fu540: Add description for RISC-V FU540 U-Boot SPL
2020-05-02 10:06 ` [PATCH v7 22/22] doc: sifive: fu540: Add description for RISC-V FU540 U-Boot SPL Pragnesh Patel
2020-05-02 12:55 ` Bin Meng
@ 2020-05-02 16:22 ` Jagan Teki
2020-05-02 16:53 ` Pragnesh Patel
2020-05-03 4:34 ` Anup Patel
2 siblings, 1 reply; 118+ messages in thread
From: Jagan Teki @ 2020-05-02 16:22 UTC (permalink / raw)
To: u-boot
On Sat, May 2, 2020 at 3:39 PM Pragnesh Patel <pragnesh.patel@sifive.com> wrote:
>
> Add descriptions about U-Boot SPL feature and how to build and run
> from MMC.
>
> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
> ---
> doc/board/sifive/fu540.rst | 376 +++++++++++++++++++++++++++++++++++++
> 1 file changed, 376 insertions(+)
>
> diff --git a/doc/board/sifive/fu540.rst b/doc/board/sifive/fu540.rst
> index 1c3d4740f3..2911e3652e 100644
> --- a/doc/board/sifive/fu540.rst
> +++ b/doc/board/sifive/fu540.rst
> @@ -38,6 +38,9 @@ TODO:
> reg = <0x0 0x2000000 0x0 0xc0000>;
> };
>
> +Booting from MMC using FSBL
> +---------------------------
> +
> Building
> --------
>
> @@ -428,3 +431,376 @@ as well.
>
> Please press Enter to activate this console.
> / #
> +
> +Booting from MMC using U-Boot SPL
> +---------------------------------
> +
> +Building
> +--------
> +
> +Before building U-Boot SPL, OpenSBI must be built first. OpenSBI can be
> +cloned and built for FU540 as below:
> +
> +.. code-block:: console
> +
> + git clone https://github.com/riscv/opensbi.git
> + cd opensbi
> + make PLATFORM=generic FW_DYNAMIC=y
> +
> +Copy OpenSBI FW_DYNAMIC image
> +(build/platform/sifive/fu540/firmware/fw_dynamic.bin) into U-Boot
> +root directory
> +
> +.. code-block:: console
> +
> + cp build/platform/sifive/fu540/firmware/fw_dynamic.bin <u-boot-dir>
> +
> +Now build the U-Boot SPL and U-Boot proper
> +
> +.. code-block:: console
> +
> + cd <U-Boot-dir>
> + make sifive_fu540_defconfig
> + make
> +
> +This will generate spl/u-boot-spl.bin and FIT image (u-boot.itb)
> +
> +
> +Flashing
> +--------
> +
> +ZSBL loads the U-Boot SPL (u-boot-spl.bin) from a partition with GUID type
> +5B193300-FC78-40CD-8002-E86C45580B47
> +
> +U-Boot SPL expects a U-Boot FIT image (u-boot.itb) from a partition with GUID
> +type 2E54B353-1271-4842-806F-E436D6AF6985
> +
> +FIT image (u-boot.itb) is a combination of fw_dynamic.bin, u-boot-nodtb.bin and
> +device tree blob (hifive-unleashed-a00.dtb)
> +
> +Format the SD card (make sure the disk has GPT, otherwise use gdisk to switch)
> +
> +.. code-block:: none
> +
> + # sudo sgdisk --clear \
> + > --set-alignment=2 \
> + > --new=1:34:2081 --change-name=1:loader1 --typecode=1:5B193300-FC78-40CD-8002-E86C45580B47 \
> + > --new=2:2082:10273 --change-name=2:loader2 --typecode=2:2E54B353-1271-4842-806F-E436D6AF6985 \
> + > --new=3:10274: --change-name=3:rootfs --typecode=3:0FC63DAF-8483-4772-8E79-3D69D8477DE4 \
> + > /dev/sda
> +
> +Program the SD card
> +
> +.. code-block:: none
> +
> + sudo dd if=spl/u-boot-spl.bin of=/dev/sda seek=34
> + sudo dd if=u-boot.itb of=/dev/sda seek=2082
> +
> +Booting
> +-------
> +Once you plugin the sdcard and power up, you should see the U-Boot prompt.
> +
> +Sample boot log from HiFive Unleashed board
> +-------------------------------------------
> +
> +.. code-block:: none
> +
> + U-Boot SPL 2020.04-rc2-00109-g63efc7e07e-dirty (Apr 30 2020 - 13:52:36 +0530)
> + Trying to boot from MMC1
> +
> +
> + U-Boot 2020.04-rc2-00109-g63efc7e07e-dirty (Apr 30 2020 - 13:52:36 +0530)
> +
> + CPU: rv64imafdc
> + Model: SiFive HiFive Unleashed A00
> + DRAM: 8 GiB
> + MMC: spi at 10050000:mmc at 0: 0
> + In: serial at 10010000
> + Out: serial at 10010000
> + Err: serial at 10010000
> + Board serial number should not be 0 !!
> + Net:
> + Warning: ethernet at 10090000 (eth0) using random MAC address - 96:06:92:18:eb:04
> + eth0: ethernet at 10090000
> + Hit any key to stop autoboot: 0
> + => version
> + U-Boot 2020.04-rc2-00109-g63efc7e07e-dirty (Apr 30 2020 - 13:52:36 +0530)
> +
> + riscv64-unknown-linux-gnu-gcc (crosstool-NG 1.24.0.37-3f461da) 9.2.0
> + GNU ld (crosstool-NG 1.24.0.37-3f461da) 2.32
> + => mmc info
> + Device: spi at 10050000:mmc at 0
> + Manufacturer ID: 3
> + OEM: 5344
> + Name: SC16G
> + Bus Speed: 20000000
> + Mode: SD Legacy
> + Rd Block Len: 512
> + SD version 2.0
> + High Capacity: Yes
> + Capacity: 14.8 GiB
> + Bus Width: 1-bit
> + Erase Group Size: 512 Bytes
> + => mmc part
> +
> + Partition Map for MMC device 0 -- Partition Type: EFI
> +
> + Part Start LBA End LBA Name
> + Attributes
> + Type GUID
> + Partition GUID
> + 1 0x00000022 0x00000821 "loader1"
> + attrs: 0x0000000000000000
> + type: 5b193300-fc78-40cd-8002-e86c45580b47
> + guid: 66e2b5d2-74db-4df8-ad6f-694b3617f87f
> + 2 0x00000822 0x00002821 "loader2"
> + attrs: 0x0000000000000000
> + type: 2e54b353-1271-4842-806f-e436d6af6985
> + guid: 8befaeaf-bca0-435d-b002-e201f37c0a2f
> + 3 0x00002822 0x01dacbde "rootfs"
> + attrs: 0x0000000000000000
> + type: 0fc63daf-8483-4772-8e79-3d69d8477de4
> + type: linux
> + guid: 9faa81b6-39b1-4418-af5e-89c48f29c20d
Upto this, will be a valid doc for SPL MMC boot, but squash it on the
patch where you enable the SPL MMC. the rest I feel unnecessary.
Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 14/22] riscv: Add place-holder for driver compilation
2020-05-02 10:06 ` [PATCH v7 14/22] riscv: Add place-holder for driver compilation Pragnesh Patel
2020-05-02 12:43 ` Bin Meng
@ 2020-05-02 16:27 ` Jagan Teki
2020-05-03 9:17 ` Pragnesh Patel
1 sibling, 1 reply; 118+ messages in thread
From: Jagan Teki @ 2020-05-02 16:27 UTC (permalink / raw)
To: u-boot
On Sat, May 2, 2020 at 3:38 PM Pragnesh Patel <pragnesh.patel@sifive.com> wrote:
>
> Add place-holder for RISC-V fu540 CPU
>
> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
> ---
> arch/riscv/include/asm/arch-fu540/clk.h | 14 +++++++++
> arch/riscv/include/asm/arch-fu540/gpio.h | 38 ++++++++++++++++++++++++
Where is it using exactly?
Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 06/22] sifive: fu540: add ddr driver
2020-05-02 15:59 ` Jagan Teki
@ 2020-05-02 16:32 ` Pragnesh Patel
0 siblings, 0 replies; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-02 16:32 UTC (permalink / raw)
To: u-boot
Hi Jagan,
>-----Original Message-----
>From: Jagan Teki <jagan@amarulasolutions.com>
>Sent: 02 May 2020 21:30
>To: Pragnesh Patel <pragnesh.patel@sifive.com>
>Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Bin
>Meng <bmeng.cn@gmail.com>; Paul Walmsley <paul.walmsley@sifive.com>;
>Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
><rick@andestech.com>; Palmer Dabbelt <palmer@dabbelt.com>; Kever Yang
><kever.yang@rock-chips.com>; Lokesh Vutla <lokeshvutla@ti.com>; Giulio
>Benetti <giulio.benetti@benettiengineering.com>; Kevin Scholz <k-
>scholz at ti.com>; YouMin Chen <cym@rock-chips.com>
>Subject: Re: [PATCH v7 06/22] sifive: fu540: add ddr driver
>
>[External Email] Do not click links or attachments unless you recognize the
>sender and know the content is safe
>
>On Sat, May 2, 2020 at 3:37 PM Pragnesh Patel <pragnesh.patel@sifive.com>
>wrote:
>>
>> Add driver for fu540 to support ddr initialization in SPL.
>> This driver is based on FSBL
>> (https://github.com/sifive/freedom-u540-c000-bootloader.git)
>>
>> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
>> ---
>> board/sifive/fu540/Kconfig | 2 +
>> drivers/ram/Kconfig | 1 +
>> drivers/ram/Makefile | 2 +
>> drivers/ram/sifive/Kconfig | 13 +
>> drivers/ram/sifive/Makefile | 6 +
>> drivers/ram/sifive/sdram_fu540.c | 416
>> +++++++++++++++++++++++++++++++
>> 6 files changed, 440 insertions(+)
>> create mode 100644 drivers/ram/sifive/Kconfig create mode 100644
>> drivers/ram/sifive/Makefile create mode 100644
>> drivers/ram/sifive/sdram_fu540.c
>>
>> diff --git a/board/sifive/fu540/Kconfig b/board/sifive/fu540/Kconfig
>> index 4330ac4491..d41c305227 100644
>> --- a/board/sifive/fu540/Kconfig
>> +++ b/board/sifive/fu540/Kconfig
>> @@ -19,6 +19,8 @@ config SYS_TEXT_BASE config
>BOARD_SPECIFIC_OPTIONS
>> # dummy
>> def_bool y
>> select GENERIC_RISCV
>> + select RAM
>> + select SPL_RAM if SPL
>> imply CMD_DHCP
>> imply CMD_EXT2
>> imply CMD_EXT4
>> diff --git a/drivers/ram/Kconfig b/drivers/ram/Kconfig index
>> 56fea7c94c..66074d1feb 100644
>> --- a/drivers/ram/Kconfig
>> +++ b/drivers/ram/Kconfig
>> @@ -75,3 +75,4 @@ config IMXRT_SDRAM
>>
>> source "drivers/ram/rockchip/Kconfig"
>> source "drivers/ram/stm32mp1/Kconfig"
>> +source "drivers/ram/sifive/Kconfig"
>> diff --git a/drivers/ram/Makefile b/drivers/ram/Makefile index
>> 5c897410c6..769c9d6218 100644
>> --- a/drivers/ram/Makefile
>> +++ b/drivers/ram/Makefile
>> @@ -17,3 +17,5 @@ obj-$(CONFIG_ARCH_MEDIATEK) += mediatek/
>> obj-$(CONFIG_K3_J721E_DDRSS) += k3-j721e/
>>
>> obj-$(CONFIG_IMXRT_SDRAM) += imxrt_sdram.o
>> +
>> +obj-$(CONFIG_RAM_SIFIVE) += sifive/
>> diff --git a/drivers/ram/sifive/Kconfig b/drivers/ram/sifive/Kconfig
>> new file mode 100644 index 0000000000..6aca22ab2a
>> --- /dev/null
>> +++ b/drivers/ram/sifive/Kconfig
>> @@ -0,0 +1,13 @@
>> +config RAM_SIFIVE
>> + bool "Ram drivers support for SiFive SoCs"
>> + depends on RAM && RISCV
>> + default y
>> + help
>> + This enables support for ram drivers of SiFive SoCs.
>> +
>> +config SIFIVE_FU540_DDR
>> + bool "SiFive FU540 DDR driver"
>> + depends on RAM_SIFIVE
>> + default y if TARGET_SIFIVE_FU540
>> + help
>> + This enables DDR support for the platforms based on SiFive FU540
>SoC.
>> diff --git a/drivers/ram/sifive/Makefile b/drivers/ram/sifive/Makefile
>> new file mode 100644 index 0000000000..0187805199
>> --- /dev/null
>> +++ b/drivers/ram/sifive/Makefile
>> @@ -0,0 +1,6 @@
>> +# SPDX-License-Identifier: GPL-2.0+
>> +#
>> +# Copyright (c) 2020 SiFive, Inc
>> +#
>> +
>> +obj-$(CONFIG_SIFIVE_FU540_DDR) += sdram_fu540.o
>> diff --git a/drivers/ram/sifive/sdram_fu540.c
>> b/drivers/ram/sifive/sdram_fu540.c
>> new file mode 100644
>> index 0000000000..0aa2b2b44a
>> --- /dev/null
>> +++ b/drivers/ram/sifive/sdram_fu540.c
>> @@ -0,0 +1,416 @@
>> +// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
>> +/*
>> + * (C) Copyright 2020 SiFive, Inc.
>> + *
>> + * Authors:
>> + * Pragnesh Patel <pragnesh.patel@sifive.com>
>> + */
>> +
>> +#include <common.h>
>> +#include <dm.h>
>> +#include <init.h>
>> +#include <ram.h>
>> +#include <regmap.h>
>> +#include <syscon.h>
>> +#include <asm/io.h>
>> +#include <clk.h>
>> +
>> +#define DENALI_CTL_0 0
>> +#define DENALI_CTL_21 21
>> +#define DENALI_CTL_120 120
>> +#define DENALI_CTL_132 132
>> +#define DENALI_CTL_136 136
>> +#define DENALI_CTL_170 170
>> +#define DENALI_CTL_181 181
>> +#define DENALI_CTL_182 182
>> +#define DENALI_CTL_184 184
>> +#define DENALI_CTL_208 208
>> +#define DENALI_CTL_209 209
>> +#define DENALI_CTL_210 210
>> +#define DENALI_CTL_212 212
>> +#define DENALI_CTL_214 214
>> +#define DENALI_CTL_216 216
>> +#define DENALI_CTL_224 224
>> +#define DENALI_CTL_225 225
>> +#define DENALI_CTL_260 260
>> +
>> +#define DENALI_PHY_1152 1152
>> +#define DENALI_PHY_1214 1214
>> +
>> +#define PAYLOAD_DEST 0x80000000
>> +#define DDR_MEM_SIZE (8UL * 1024UL * 1024UL * 1024UL)
>> +
>> +#define DRAM_CLASS_OFFSET 8
>> +#define DRAM_CLASS_DDR4 0xA
>> +#define OPTIMAL_RMODW_EN_OFFSET 0
>> +#define DISABLE_RD_INTERLEAVE_OFFSET 16
>> +#define OUT_OF_RANGE_OFFSET 1
>> +#define MULTIPLE_OUT_OF_RANGE_OFFSET 2
>> +#define PORT_COMMAND_CHANNEL_ERROR_OFFSET 7
>> +#define MC_INIT_COMPLETE_OFFSET 8
>> +#define LEVELING_OPERATION_COMPLETED_OFFSET 22
>> +#define DFI_PHY_WRLELV_MODE_OFFSET 24
>> +#define DFI_PHY_RDLVL_MODE_OFFSET 24
>> +#define DFI_PHY_RDLVL_GATE_MODE_OFFSET 0
>> +#define VREF_EN_OFFSET 24
>> +#define PORT_ADDR_PROTECTION_EN_OFFSET 0
>> +#define AXI0_ADDRESS_RANGE_ENABLE 8
>> +#define AXI0_RANGE_PROT_BITS_0_OFFSET 24
>> +#define RDLVL_EN_OFFSET 16
>> +#define RDLVL_GATE_EN_OFFSET 24
>> +#define WRLVL_EN_OFFSET 0
>> +
>> +#define PHY_RX_CAL_DQ0_0_OFFSET 0
>> +#define PHY_RX_CAL_DQ1_0_OFFSET 16
>> +
>> +struct fu540_ddrctl {
>> + volatile u32 denali_ctl[265];
>> +};
>> +
>> +struct fu540_ddrphy {
>> + volatile u32 denali_phy[1215]; };
>> +
>> +/**
>> + * struct ddr_info
>> + *
>> + * @dev : pointer for the device
>> + * @info : UCLASS RAM information
>> + * @ctl : DDR controller base address
>> + * @phy : DDR PHY base address
>> + * @ctrl : DDR control base address
>> + * @physical_filter_ctrl : DDR physical filter control base address
>> + */
>> +struct ddr_info {
>> + struct udevice *dev;
>> + struct ram_info info;
>> + struct fu540_ddrctl *ctl;
>> + struct fu540_ddrphy *phy;
>> + struct clk ddr_clk;
>> + u32 *physical_filter_ctrl;
>> +};
>> +
>> +#if defined(CONFIG_TPL_BUILD) || \
>> + (!defined(CONFIG_TPL) && defined(CONFIG_SPL_BUILD))
>> +
>> +struct fu540_sdram_params {
>> + struct fu540_ddrctl pctl_regs;
>> + struct fu540_ddrphy phy_regs;
>> +};
>> +
>> +struct sifive_dmc_plat {
>> +#if CONFIG_IS_ENABLED(OF_PLATDATA)
>> + struct dtd_sifive_fu540_dmc dtplat; #else
>> + struct fu540_sdram_params sdram_params; #endif };
>> +
>> +/* n: Unit bytes */
>
>Please add TODO "It can be possible to use common copy_to_reg API"
Will update in v8.
>
>> +static void sdram_copy_to_reg(volatile u32 *dest,
>> + volatile u32 *src, u32 n) {
>> + int i;
>> +
>> + for (i = 0; i < n / sizeof(u32); i++) {
>> + writel(*src, dest);
>> + src++;
>> + dest++;
>> + }
>> +}
>> +
>> +static void ddr_setuprangeprotection(volatile u32 *ctl, u64 end_addr)
>> +{
>> + u32 end_addr_16kblocks = ((end_addr >> 14) & 0x7FFFFF) - 1;
>> +
>> + writel(0x0, DENALI_CTL_209 + ctl);
>> + writel(end_addr_16kblocks, DENALI_CTL_210 + ctl);
>> + writel(0x0, DENALI_CTL_212 + ctl);
>> + writel(0x0, DENALI_CTL_214 + ctl);
>> + writel(0x0, DENALI_CTL_216 + ctl);
>> + setbits_le32(DENALI_CTL_224 + ctl,
>> + 0x3 << AXI0_RANGE_PROT_BITS_0_OFFSET);
>> + writel(0xFFFFFFFF, DENALI_CTL_225 + ctl);
>> + setbits_le32(DENALI_CTL_208 + ctl, 0x1 <<
>AXI0_ADDRESS_RANGE_ENABLE);
>> + setbits_le32(DENALI_CTL_208 + ctl,
>> + 0x1 << PORT_ADDR_PROTECTION_EN_OFFSET); }
>> +
>> +static void ddr_start(volatile u32 *ctl, u32 *physical_filter_ctrl,
>> +u64 ddr_end) {
>> + int val;
>> +
>> + volatile u64 *filterreg = (volatile u64
>> + *)physical_filter_ctrl;
>> +
>> + setbits_le32(DENALI_CTL_0 + ctl, 0x1);
>> +
>> + do {
>> + val = readl(DENALI_CTL_132 + ctl) &
>> + (1 << MC_INIT_COMPLETE_OFFSET);
>> + } while (val == 0);
>
>wait_for_bit_le32(DENALI_CTL_132 + ctl, BIT(MC_INIT_COMPLETE_OFFSET),
>true, 100, false);
Will update in v8, thanks for the review.
>
>otherwise,
>
>Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 13/22] riscv: cpu: fu540: Add support for cpu fu540
2020-05-02 10:06 ` [PATCH v7 13/22] riscv: cpu: fu540: Add support for cpu fu540 Pragnesh Patel
2020-05-02 12:32 ` Bin Meng
@ 2020-05-02 16:34 ` Jagan Teki
2020-05-03 9:16 ` Pragnesh Patel
1 sibling, 1 reply; 118+ messages in thread
From: Jagan Teki @ 2020-05-02 16:34 UTC (permalink / raw)
To: u-boot
On Sat, May 2, 2020 at 3:38 PM Pragnesh Patel <pragnesh.patel@sifive.com> wrote:
>
> Add SiFive fu540 cpu to support RISC-V arch
This looks like a new patch in this series, isn't it?
>
> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
> ---
Good practice is to add "changes for 7" so-that it is easy for reviews
to find what is new in this series.
> arch/riscv/Kconfig | 1 +
> arch/riscv/cpu/fu540/Kconfig | 15 ++++++++++++++
> arch/riscv/cpu/fu540/Makefile | 7 +++++++
> arch/riscv/cpu/fu540/cpu.c | 22 ++++++++++++++++++++
> arch/riscv/cpu/fu540/dram.c | 38 +++++++++++++++++++++++++++++++++++
> 5 files changed, 83 insertions(+)
> create mode 100644 arch/riscv/cpu/fu540/Kconfig
> create mode 100644 arch/riscv/cpu/fu540/Makefile
> create mode 100644 arch/riscv/cpu/fu540/cpu.c
> create mode 100644 arch/riscv/cpu/fu540/dram.c
>
> diff --git a/arch/riscv/Kconfig b/arch/riscv/Kconfig
> index fb5fe5afff..3044609971 100644
> --- a/arch/riscv/Kconfig
> +++ b/arch/riscv/Kconfig
> @@ -57,6 +57,7 @@ source "board/sifive/fu540/Kconfig"
> # platform-specific options below
> source "arch/riscv/cpu/ax25/Kconfig"
> source "arch/riscv/cpu/generic/Kconfig"
> +source "arch/riscv/cpu/fu540/Kconfig"
>
> # architecture-specific options below
>
> diff --git a/arch/riscv/cpu/fu540/Kconfig b/arch/riscv/cpu/fu540/Kconfig
> new file mode 100644
> index 0000000000..b2cb155d6d
> --- /dev/null
> +++ b/arch/riscv/cpu/fu540/Kconfig
> @@ -0,0 +1,15 @@
> +# SPDX-License-Identifier: GPL-2.0+
> +#
> +# Copyright (C) 2018, Bin Meng <bmeng.cn@gmail.com>
> +
> +config GENERIC_RISCV
> + bool
> + select ARCH_EARLY_INIT_R
> + imply CPU
> + imply CPU_RISCV
> + imply RISCV_TIMER
> + imply SIFIVE_CLINT if (RISCV_MMODE || SPL_RISCV_MMODE)
> + imply CMD_CPU
> + imply SPL_CPU_SUPPORT
> + imply SPL_OPENSBI
> + imply SPL_LOAD_FIT
> diff --git a/arch/riscv/cpu/fu540/Makefile b/arch/riscv/cpu/fu540/Makefile
> new file mode 100644
> index 0000000000..44700d998c
> --- /dev/null
> +++ b/arch/riscv/cpu/fu540/Makefile
> @@ -0,0 +1,7 @@
> +# SPDX-License-Identifier: GPL-2.0+
> +#
> +# Copyright (C) 2020 SiFive, Inc
> +# Pragnesh Patel <pragnesh.patel@sifive.com>
> +
> +obj-y += dram.o
> +obj-y += cpu.o
> diff --git a/arch/riscv/cpu/fu540/cpu.c b/arch/riscv/cpu/fu540/cpu.c
> new file mode 100644
> index 0000000000..13a69ef0cc
> --- /dev/null
> +++ b/arch/riscv/cpu/fu540/cpu.c
> @@ -0,0 +1,22 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (C) 2018, Bin Meng <bmeng.cn@gmail.com>
> + */
> +
> +#include <common.h>
> +#include <irq_func.h>
> +
> +/*
> + * cleanup_before_linux() is called just before we call linux
> + * it prepares the processor for linux
> + *
> + * we disable interrupt and caches.
> + */
> +int cleanup_before_linux(void)
> +{
> + disable_interrupts();
> +
> + cache_flush();
> +
> + return 0;
> +}
> diff --git a/arch/riscv/cpu/fu540/dram.c b/arch/riscv/cpu/fu540/dram.c
> new file mode 100644
> index 0000000000..1dc77efeca
> --- /dev/null
> +++ b/arch/riscv/cpu/fu540/dram.c
> @@ -0,0 +1,38 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (C) 2018, Bin Meng <bmeng.cn@gmail.com>
> + */
> +
> +#include <common.h>
> +#include <fdtdec.h>
> +#include <init.h>
> +#include <linux/sizes.h>
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +int dram_init(void)
> +{
> + return fdtdec_setup_mem_size_base();
> +}
> +
> +int dram_init_banksize(void)
> +{
> + return fdtdec_setup_memory_banksize();
> +}
> +
> +ulong board_get_usable_ram_top(ulong total_size)
> +{
> +#ifdef CONFIG_64BIT
> + /*
> + * Ensure that we run from first 4GB so that all
> + * addresses used by U-Boot are 32bit addresses.
> + *
> + * This in-turn ensures that 32bit DMA capable
> + * devices work fine because DMA mapping APIs will
> + * provide 32bit DMA addresses only.
> + */
> + if (gd->ram_top > SZ_4G)
> + return SZ_4G;
> +#endif
> + return gd->ram_top;
Is all this code common across SPL and U-Boot proper? except that SPL
config imply.
Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 10/22] clk: sifive: fu540-prci: ddr and ethernet clock initialization in SPL
2020-05-02 16:14 ` Jagan Teki
@ 2020-05-02 16:35 ` Pragnesh Patel
2020-05-02 16:44 ` Jagan Teki
0 siblings, 1 reply; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-02 16:35 UTC (permalink / raw)
To: u-boot
Hi Jagan,
>-----Original Message-----
>From: Jagan Teki <jagan@amarulasolutions.com>
>Sent: 02 May 2020 21:44
>To: Pragnesh Patel <pragnesh.patel@sifive.com>
>Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Bin
>Meng <bmeng.cn@gmail.com>; Paul Walmsley <paul.walmsley@sifive.com>;
>Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
><rick@andestech.com>; Lukasz Majewski <lukma@denx.de>; Anatolij
>Gustschin <agust@denx.de>; Simon Glass <sjg@chromium.org>
>Subject: Re: [PATCH v7 10/22] clk: sifive: fu540-prci: ddr and ethernet clock
>initialization in SPL
>
>[External Email] Do not click links or attachments unless you recognize the
>sender and know the content is safe
>
>On Sat, May 2, 2020 at 3:38 PM Pragnesh Patel <pragnesh.patel@sifive.com>
>wrote:
>>
>> Add ddr clock release reset and ehternet clock initialization for SPL
>
>Why ethernet still require for SPL?
I think we have already discussed this in v6.
https://patchwork.ozlabs.org/project/uboot/patch/20200329170538.25449-10-pragnesh.patel at sifive.com/
>
>Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
2020-05-02 16:18 ` Jagan Teki
@ 2020-05-02 16:42 ` Pragnesh Patel
2020-05-02 17:13 ` Jagan Teki
0 siblings, 1 reply; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-02 16:42 UTC (permalink / raw)
To: u-boot
Hi Jagan,
>-----Original Message-----
>From: Jagan Teki <jagan@amarulasolutions.com>
>Sent: 02 May 2020 21:49
>To: Pragnesh Patel <pragnesh.patel@sifive.com>
>Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Bin
>Meng <bmeng.cn@gmail.com>; Paul Walmsley <paul.walmsley@sifive.com>;
>Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
><rick@andestech.com>
>Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
>
>[External Email] Do not click links or attachments unless you recognize the
>sender and know the content is safe
>
>On Sat, May 2, 2020 at 3:39 PM Pragnesh Patel <pragnesh.patel@sifive.com>
>wrote:
>>
>> Add L2 cache node to enable cache ways from U-Boot
>
>This and 20/22 doesn't relate to SPL MMC boot?, if yes please send them
>separately.
This series is for replacing FSBL and all the patches are related to that.
IMHO it's better to add all FSBL functionality in one series.
>
>Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 10/22] clk: sifive: fu540-prci: ddr and ethernet clock initialization in SPL
2020-05-02 16:35 ` Pragnesh Patel
@ 2020-05-02 16:44 ` Jagan Teki
2020-05-03 8:57 ` Pragnesh Patel
0 siblings, 1 reply; 118+ messages in thread
From: Jagan Teki @ 2020-05-02 16:44 UTC (permalink / raw)
To: u-boot
On Sat, May 2, 2020 at 10:05 PM Pragnesh Patel
<pragnesh.patel@sifive.com> wrote:
>
> Hi Jagan,
>
> >-----Original Message-----
> >From: Jagan Teki <jagan@amarulasolutions.com>
> >Sent: 02 May 2020 21:44
> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> ><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Bin
> >Meng <bmeng.cn@gmail.com>; Paul Walmsley <paul.walmsley@sifive.com>;
> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
> ><rick@andestech.com>; Lukasz Majewski <lukma@denx.de>; Anatolij
> >Gustschin <agust@denx.de>; Simon Glass <sjg@chromium.org>
> >Subject: Re: [PATCH v7 10/22] clk: sifive: fu540-prci: ddr and ethernet clock
> >initialization in SPL
> >
> >[External Email] Do not click links or attachments unless you recognize the
> >sender and know the content is safe
> >
> >On Sat, May 2, 2020 at 3:38 PM Pragnesh Patel <pragnesh.patel@sifive.com>
> >wrote:
> >>
> >> Add ddr clock release reset and ehternet clock initialization for SPL
> >
> >Why ethernet still require for SPL?
>
> I think we have already discussed this in v6.
> https://patchwork.ozlabs.org/project/uboot/patch/20200329170538.25449-10-pragnesh.patel at sifive.com/
Understand, then make a separate patch for "Ethernet SPL" but not in
this series.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 15/22] riscv: sifive: dts: fu540: Add clock for cpus node
2020-05-02 10:06 ` [PATCH v7 15/22] riscv: sifive: dts: fu540: Add clock for cpus node Pragnesh Patel
2020-05-02 12:43 ` Bin Meng
@ 2020-05-02 16:50 ` Jagan Teki
2020-05-03 8:55 ` Pragnesh Patel
1 sibling, 1 reply; 118+ messages in thread
From: Jagan Teki @ 2020-05-02 16:50 UTC (permalink / raw)
To: u-boot
On Sat, May 2, 2020 at 3:38 PM Pragnesh Patel <pragnesh.patel@sifive.com> wrote:
>
> Add clock-frequency and clocks in cpus node, so that
> clock will be enabled by cpu driver.
>
> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
> ---
Squash this with 05/22
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 18/22] configs: fu540: Add config options for U-Boot SPL
2020-05-02 10:06 ` [PATCH v7 18/22] configs: fu540: Add config options for U-Boot SPL Pragnesh Patel
2020-05-02 12:55 ` Bin Meng
@ 2020-05-02 16:51 ` Jagan Teki
2020-05-04 15:48 ` Pragnesh Patel
2020-05-02 17:15 ` Jagan Teki
2 siblings, 1 reply; 118+ messages in thread
From: Jagan Teki @ 2020-05-02 16:51 UTC (permalink / raw)
To: u-boot
On Sat, May 2, 2020 at 3:38 PM Pragnesh Patel <pragnesh.patel@sifive.com> wrote:
>
> With sifive_fu540_defconfig:
>
> User can use FSBL or u-boot-spl.bin anyone at a time.
>
> For FSBL,
> fsbl->fw_payload.bin (opensbi + U-Boot)
>
> For u-boot-spl.bin,
> u-boot-spl.bin->FIT image (opensbi + U-Boot + dtb)
>
> U-Boot SPL will be loaded by ZSBL from SD card (replace fsbl.bin with
> u-boot-spl.bin) and runs in L2 LIM in machine mode and then load FIT
> image u-boot.itb from SD card into RAM.
>
> U-Boot SPL expects u-boot.itb FIT image at the starting of SD card sector
> number (0x822) of GUID type "2E54B353-1271-4842-806F-E436D6AF6985"
>
> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
> ---
squash with 12/22 and 22/22.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 22/22] doc: sifive: fu540: Add description for RISC-V FU540 U-Boot SPL
2020-05-02 16:22 ` Jagan Teki
@ 2020-05-02 16:53 ` Pragnesh Patel
0 siblings, 0 replies; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-02 16:53 UTC (permalink / raw)
To: u-boot
Hi Jagan,
>-----Original Message-----
>From: Jagan Teki <jagan@amarulasolutions.com>
>Sent: 02 May 2020 21:53
>To: Pragnesh Patel <pragnesh.patel@sifive.com>
>Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Bin
>Meng <bmeng.cn@gmail.com>; Paul Walmsley <paul.walmsley@sifive.com>;
>Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
><rick@andestech.com>; Joe Hershberger <joe.hershberger@ni.com>
>Subject: Re: [PATCH v7 22/22] doc: sifive: fu540: Add description for RISC-V
>FU540 U-Boot SPL
>
>[External Email] Do not click links or attachments unless you recognize the
>sender and know the content is safe
>
>On Sat, May 2, 2020 at 3:39 PM Pragnesh Patel <pragnesh.patel@sifive.com>
>wrote:
>>
>> Add descriptions about U-Boot SPL feature and how to build and run
>> from MMC.
>>
>> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
>> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
>> ---
>> doc/board/sifive/fu540.rst | 376
>> +++++++++++++++++++++++++++++++++++++
>> 1 file changed, 376 insertions(+)
>>
>> diff --git a/doc/board/sifive/fu540.rst b/doc/board/sifive/fu540.rst
>> index 1c3d4740f3..2911e3652e 100644
>> --- a/doc/board/sifive/fu540.rst
>> +++ b/doc/board/sifive/fu540.rst
>> @@ -38,6 +38,9 @@ TODO:
>> reg = <0x0 0x2000000 0x0 0xc0000>;
>> };
>>
>> +Booting from MMC using FSBL
>> +---------------------------
>> +
>> Building
>> --------
>>
>> @@ -428,3 +431,376 @@ as well.
>>
>> Please press Enter to activate this console.
>> / #
>> +
>> +Booting from MMC using U-Boot SPL
>> +---------------------------------
>> +
>> +Building
>> +--------
>> +
>> +Before building U-Boot SPL, OpenSBI must be built first. OpenSBI can
>> +be cloned and built for FU540 as below:
>> +
>> +.. code-block:: console
>> +
>> + git clone https://github.com/riscv/opensbi.git
>> + cd opensbi
>> + make PLATFORM=generic FW_DYNAMIC=y
>> +
>> +Copy OpenSBI FW_DYNAMIC image
>> +(build/platform/sifive/fu540/firmware/fw_dynamic.bin) into U-Boot
>> +root directory
>> +
>> +.. code-block:: console
>> +
>> + cp build/platform/sifive/fu540/firmware/fw_dynamic.bin
>> + <u-boot-dir>
>> +
>> +Now build the U-Boot SPL and U-Boot proper
>> +
>> +.. code-block:: console
>> +
>> + cd <U-Boot-dir>
>> + make sifive_fu540_defconfig
>> + make
>> +
>> +This will generate spl/u-boot-spl.bin and FIT image (u-boot.itb)
>> +
>> +
>> +Flashing
>> +--------
>> +
>> +ZSBL loads the U-Boot SPL (u-boot-spl.bin) from a partition with GUID
>> +type
>> +5B193300-FC78-40CD-8002-E86C45580B47
>> +
>> +U-Boot SPL expects a U-Boot FIT image (u-boot.itb) from a partition
>> +with GUID type 2E54B353-1271-4842-806F-E436D6AF6985
>> +
>> +FIT image (u-boot.itb) is a combination of fw_dynamic.bin,
>> +u-boot-nodtb.bin and device tree blob (hifive-unleashed-a00.dtb)
>> +
>> +Format the SD card (make sure the disk has GPT, otherwise use gdisk
>> +to switch)
>> +
>> +.. code-block:: none
>> +
>> + # sudo sgdisk --clear \
>> + > --set-alignment=2 \
>> + > --new=1:34:2081 --change-name=1:loader1 --typecode=1:5B193300-
>FC78-40CD-8002-E86C45580B47 \
>> + > --new=2:2082:10273 --change-name=2:loader2 --
>typecode=2:2E54B353-1271-4842-806F-E436D6AF6985 \
>> + > --new=3:10274: --change-name=3:rootfs --typecode=3:0FC63DAF-
>8483-4772-8E79-3D69D8477DE4 \
>> + > /dev/sda
>> +
>> +Program the SD card
>> +
>> +.. code-block:: none
>> +
>> + sudo dd if=spl/u-boot-spl.bin of=/dev/sda seek=34
>> + sudo dd if=u-boot.itb of=/dev/sda seek=2082
>> +
>> +Booting
>> +-------
>> +Once you plugin the sdcard and power up, you should see the U-Boot
>prompt.
>> +
>> +Sample boot log from HiFive Unleashed board
>> +-------------------------------------------
>> +
>> +.. code-block:: none
>> +
>> + U-Boot SPL 2020.04-rc2-00109-g63efc7e07e-dirty (Apr 30 2020 -
>13:52:36 +0530)
>> + Trying to boot from MMC1
>> +
>> +
>> + U-Boot 2020.04-rc2-00109-g63efc7e07e-dirty (Apr 30 2020 -
>> + 13:52:36 +0530)
>> +
>> + CPU: rv64imafdc
>> + Model: SiFive HiFive Unleashed A00
>> + DRAM: 8 GiB
>> + MMC: spi at 10050000:mmc at 0: 0
>> + In: serial at 10010000
>> + Out: serial at 10010000
>> + Err: serial at 10010000
>> + Board serial number should not be 0 !!
>> + Net:
>> + Warning: ethernet at 10090000 (eth0) using random MAC address -
>96:06:92:18:eb:04
>> + eth0: ethernet at 10090000
>> + Hit any key to stop autoboot: 0
>> + => version
>> + U-Boot 2020.04-rc2-00109-g63efc7e07e-dirty (Apr 30 2020 -
>> + 13:52:36 +0530)
>> +
>> + riscv64-unknown-linux-gnu-gcc (crosstool-NG 1.24.0.37-3f461da) 9.2.0
>> + GNU ld (crosstool-NG 1.24.0.37-3f461da) 2.32
>> + => mmc info
>> + Device: spi at 10050000:mmc at 0
>> + Manufacturer ID: 3
>> + OEM: 5344
>> + Name: SC16G
>> + Bus Speed: 20000000
>> + Mode: SD Legacy
>> + Rd Block Len: 512
>> + SD version 2.0
>> + High Capacity: Yes
>> + Capacity: 14.8 GiB
>> + Bus Width: 1-bit
>> + Erase Group Size: 512 Bytes
>> + => mmc part
>> +
>> + Partition Map for MMC device 0 -- Partition Type: EFI
>> +
>> + Part Start LBA End LBA Name
>> + Attributes
>> + Type GUID
>> + Partition GUID
>> + 1 0x00000022 0x00000821 "loader1"
>> + attrs: 0x0000000000000000
>> + type: 5b193300-fc78-40cd-8002-e86c45580b47
>> + guid: 66e2b5d2-74db-4df8-ad6f-694b3617f87f
>> + 2 0x00000822 0x00002821 "loader2"
>> + attrs: 0x0000000000000000
>> + type: 2e54b353-1271-4842-806f-e436d6af6985
>> + guid: 8befaeaf-bca0-435d-b002-e201f37c0a2f
>> + 3 0x00002822 0x01dacbde "rootfs"
>> + attrs: 0x0000000000000000
>> + type: 0fc63daf-8483-4772-8e79-3d69d8477de4
>> + type: linux
>> + guid: 9faa81b6-39b1-4418-af5e-89c48f29c20d
>
>Upto this, will be a valid doc for SPL MMC boot, but squash it on the patch
>where you enable the SPL MMC. the rest I feel unnecessary.
I am okay with your suggestion, will update in v8.
>
>Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 18/22] configs: fu540: Add config options for U-Boot SPL
2020-05-02 12:55 ` Bin Meng
2020-05-02 14:37 ` Pragnesh Patel
@ 2020-05-02 17:04 ` Jagan Teki
1 sibling, 0 replies; 118+ messages in thread
From: Jagan Teki @ 2020-05-02 17:04 UTC (permalink / raw)
To: u-boot
On Sat, May 2, 2020 at 6:25 PM Bin Meng <bmeng.cn@gmail.com> wrote:
>
> Hi Pragnesh,
>
> On Sat, May 2, 2020 at 6:08 PM Pragnesh Patel <pragnesh.patel@sifive.com> wrote:
> >
> > With sifive_fu540_defconfig:
> >
> > User can use FSBL or u-boot-spl.bin anyone at a time.
> >
> > For FSBL,
> > fsbl->fw_payload.bin (opensbi + U-Boot)
> >
> > For u-boot-spl.bin,
> > u-boot-spl.bin->FIT image (opensbi + U-Boot + dtb)
> >
> > U-Boot SPL will be loaded by ZSBL from SD card (replace fsbl.bin with
> > u-boot-spl.bin) and runs in L2 LIM in machine mode and then load FIT
> > image u-boot.itb from SD card into RAM.
> >
> > U-Boot SPL expects u-boot.itb FIT image at the starting of SD card sector
> > number (0x822) of GUID type "2E54B353-1271-4842-806F-E436D6AF6985"
> >
> > Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
> > ---
> > configs/sifive_fu540_defconfig | 9 +++++++++
> > 1 file changed, 9 insertions(+)
> >
> > diff --git a/configs/sifive_fu540_defconfig b/configs/sifive_fu540_defconfig
> > index f805aacc7a..30fac8996b 100644
> > --- a/configs/sifive_fu540_defconfig
> > +++ b/configs/sifive_fu540_defconfig
> > @@ -1,6 +1,12 @@
> > CONFIG_RISCV=y
> > +CONFIG_SPL_GPIO_SUPPORT=y
> > +CONFIG_SYS_MALLOC_F_LEN=0x3000
> > CONFIG_ENV_SIZE=0x20000
> > +CONFIG_SPL_MMC_SUPPORT=y
> > CONFIG_NR_DRAM_BANKS=1
> > +CONFIG_SPL=y
> > +CONFIG_SPL_SPI_SUPPORT=y
> > +CONFIG_SPL_PAYLOAD="u-boot.itb"
This won't require.
> > CONFIG_TARGET_SIFIVE_FU540=y
> > CONFIG_ARCH_RV64I=y
> > CONFIG_RISCV_SMODE=y
> > @@ -9,7 +15,10 @@ CONFIG_FIT=y
> > CONFIG_MISC_INIT_R=y
> > CONFIG_DISPLAY_CPUINFO=y
> > CONFIG_DISPLAY_BOARDINFO=y
> > +CONFIG_SPL_SEPARATE_BSS=y
> > +CONFIG_SPL_YMODEM_SUPPORT=y
>
> Is this needed for SPL?
Yes, it is required for mmc_spi to build on the SPL side.
riscv64-buildroot-linux-gnu-ld.bfd: drivers/built-in.o: in function
`mmc_spi_readdata':
u-boot/drivers/mmc/mmc_spi.c:157: undefined reference to `crc16_ccitt'
riscv64-buildroot-linux-gnu-ld.bfd: drivers/built-in.o: in function
`dm_mmc_spi_request':
u-boot/drivers/mmc/mmc_spi.c:368: undefined reference to `crc16_ccitt'
Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
2020-05-02 16:42 ` Pragnesh Patel
@ 2020-05-02 17:13 ` Jagan Teki
2020-05-03 7:27 ` Pragnesh Patel
0 siblings, 1 reply; 118+ messages in thread
From: Jagan Teki @ 2020-05-02 17:13 UTC (permalink / raw)
To: u-boot
On Sat, May 2, 2020 at 10:12 PM Pragnesh Patel
<pragnesh.patel@sifive.com> wrote:
>
> Hi Jagan,
>
> >-----Original Message-----
> >From: Jagan Teki <jagan@amarulasolutions.com>
> >Sent: 02 May 2020 21:49
> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> ><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Bin
> >Meng <bmeng.cn@gmail.com>; Paul Walmsley <paul.walmsley@sifive.com>;
> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
> ><rick@andestech.com>
> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
> >
> >[External Email] Do not click links or attachments unless you recognize the
> >sender and know the content is safe
> >
> >On Sat, May 2, 2020 at 3:39 PM Pragnesh Patel <pragnesh.patel@sifive.com>
> >wrote:
> >>
> >> Add L2 cache node to enable cache ways from U-Boot
> >
> >This and 20/22 doesn't relate to SPL MMC boot?, if yes please send them
> >separately.
>
> This series is for replacing FSBL and all the patches are related to that.
> IMHO it's better to add all FSBL functionality in one series.
You mean does it break existing FSBL flow? if yes add proper commit
message, but I am able to boot SPL MMC w/o this?
Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 18/22] configs: fu540: Add config options for U-Boot SPL
2020-05-02 10:06 ` [PATCH v7 18/22] configs: fu540: Add config options for U-Boot SPL Pragnesh Patel
2020-05-02 12:55 ` Bin Meng
2020-05-02 16:51 ` Jagan Teki
@ 2020-05-02 17:15 ` Jagan Teki
2020-05-03 7:20 ` Pragnesh Patel
2 siblings, 1 reply; 118+ messages in thread
From: Jagan Teki @ 2020-05-02 17:15 UTC (permalink / raw)
To: u-boot
On Sat, May 2, 2020 at 3:38 PM Pragnesh Patel <pragnesh.patel@sifive.com> wrote:
>
> With sifive_fu540_defconfig:
>
> User can use FSBL or u-boot-spl.bin anyone at a time.
>
> For FSBL,
> fsbl->fw_payload.bin (opensbi + U-Boot)
>
> For u-boot-spl.bin,
> u-boot-spl.bin->FIT image (opensbi + U-Boot + dtb)
>
> U-Boot SPL will be loaded by ZSBL from SD card (replace fsbl.bin with
> u-boot-spl.bin) and runs in L2 LIM in machine mode and then load FIT
> image u-boot.itb from SD card into RAM.
>
> U-Boot SPL expects u-boot.itb FIT image at the starting of SD card sector
> number (0x822) of GUID type "2E54B353-1271-4842-806F-E436D6AF6985"
>
Prior to this patch you have
https://patchwork.ozlabs.org/project/uboot/patch/20200420133735.23599-1-jagan at amarulasolutions.com/
https://patchwork.ozlabs.org/project/uboot/patch/20200420133735.23599-2-jagan at amarulasolutions.com/
in the series, otherwise it will not boot from MMC with this series.
Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 00/22] RISC-V SiFive FU540 support SPL
2020-05-02 10:06 [PATCH v7 00/22] RISC-V SiFive FU540 support SPL Pragnesh Patel
` (21 preceding siblings ...)
2020-05-02 10:06 ` [PATCH v7 22/22] doc: sifive: fu540: Add description for RISC-V FU540 U-Boot SPL Pragnesh Patel
@ 2020-05-02 17:18 ` Jagan Teki
2020-05-03 7:19 ` Pragnesh Patel
22 siblings, 1 reply; 118+ messages in thread
From: Jagan Teki @ 2020-05-02 17:18 UTC (permalink / raw)
To: u-boot
On Sat, May 2, 2020 at 3:37 PM Pragnesh Patel <pragnesh.patel@sifive.com> wrote:
>
> This series add support for SPL to FU540.U-Boot SPL can boot from
> L2 LIM (0x0800_0000) and jump to OpenSBI(FW_DYNAMIC firmware) and
> U-Boot proper from MMC devices.
>
> How to test this patch:
> 1) Go to OpenSBI-dir : make PLATFORM=generic FW_DYNAMIC=y
> 2) export OPENSBI=<path/to/opensbi/install_dir/platform/generic/firmware/fw_dynamic.bin>
> 3) Change to u-boot-dir
> 4) make sifive_fu540_defconfig
> 5) make all
> 6) Format the SD card (make sure the disk has GPT, otherwise use gdisk to switch)
>
> # sudo sgdisk --clear \
> > --set-alignment=2 \
> > --new=1:34:2081 --change-name=1:loader1 --typecode=1:5B193300-FC78-40CD-8002-E86C45580B47 \
> > --new=2:2082:10273 --change-name=2:loader2 --typecode=2:2E54B353-1271-4842-806F-E436D6AF6985 \
> > --new=3:10274: --change-name=3:rootfs --typecode=3:0FC63DAF-8483-4772-8E79-3D69D8477DE4 \
> > /dev/sda
>
> 7) sudo dd if=spl/u-boot-spl.bin of=/dev/sda seek=34
> 8) sudo dd if=u-boot.itb of=/dev/sda seek=2082
Most patches improved from v6, but still few issues like
- patches which are unrelated to MMC SPL support, please bypass and
send them separately.
- order of patches need to improve, take my suggestions and order them.
- incorporate partition layout patches before SPL enablement patch.
Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 16/22] riscv: Enable cpu clock if it is present
2020-05-02 10:06 ` [PATCH v7 16/22] riscv: Enable cpu clock if it is present Pragnesh Patel
2020-05-02 12:55 ` Bin Meng
@ 2020-05-02 18:15 ` Sean Anderson
2020-05-03 7:12 ` Pragnesh Patel
1 sibling, 1 reply; 118+ messages in thread
From: Sean Anderson @ 2020-05-02 18:15 UTC (permalink / raw)
To: u-boot
On 5/2/20 6:06 AM, Pragnesh Patel wrote:
> The cpu clock is probably already enabled if we are executing code (though
> we could be executing from a different core). This patch prevents the cpu
> clock or its parents from being disabled.
>
> Signed-off-by: Sean Anderson <seanga2@gmail.com>
If you make substantial changes can you please make a note of it in the
commit? I did not sign off on *this* code.
> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
> ---
> drivers/cpu/riscv_cpu.c | 33 +++++++++++++++++++++++++++++++++
> 1 file changed, 33 insertions(+)
>
> diff --git a/drivers/cpu/riscv_cpu.c b/drivers/cpu/riscv_cpu.c
> index 28ad0aa30f..8ebe0341fd 100644
> --- a/drivers/cpu/riscv_cpu.c
> +++ b/drivers/cpu/riscv_cpu.c
> @@ -9,6 +9,7 @@
> #include <errno.h>
> #include <dm/device-internal.h>
> #include <dm/lists.h>
> +#include <clk.h>
>
> DECLARE_GLOBAL_DATA_PTR;
>
> @@ -100,6 +101,37 @@ static int riscv_cpu_bind(struct udevice *dev)
> return 0;
> }
>
> +static int riscv_cpu_probe(struct udevice *dev)
> +{
> + int ret = 0;
> + u32 clock = 0;
> + struct clk clk;
> +
> + /* Get a clock if it exists */
> + ret = clk_get_by_index(dev, 0, &clk);
> + if (ret)
> + return 0;
> +
> + ret = dev_read_u32(dev, "clock-frequency", &clock);
Ok, so as I understand it, your goal for your changes this patch is to
have a way to set the cpu frequency on startup. However, I think the
cpu-frequency property is not the correct way to go about this when we
have a clock from the device tree. In this case, one should use the
assigned-clock* properties to have the frequency set automatically when
clk_get_by_index is called. There is no need to add this functionality
here.
With the previous patch in the series you pulled this from [1], one
could easily do something like
cpus {
assigned-clocks = <&foo FOO_CPU>;
assigned-clock-frequency = <100000000>;
cpu at 0 {
/* ... */
clocks = <&foo FOO_CPU>;
/* ... */
};
};
which would use existing code to assign the frequency.
[1] https://patchwork.ozlabs.org/project/uboot/patch/20200423023320.1380090-18-seanga2 at gmail.com/
> + if (ret) {
> + debug("clock-frequency not found in dt %d\n", ret);
This should not be an error. You also need to check for ENOSYS and
ENOTSUPP like below.
> + return ret;
> + } else {
> + ret = clk_set_rate(&clk, clock);
> + if (ret < 0) {
> + debug("Could not set CPU clock\n");
Neither should this be.
> + return ret;
> + }
> + }
> +
> + ret = clk_enable(&clk);
> + clk_free(&clk);
> + if (ret == -ENOSYS || ret == -ENOTSUPP)
All clk_ calls can return ENOSYS and ENOTSUPP. These are returned when
the underlying clock does not support the operation. However, they are
not appropriate errors to return from this function.
> + return 0;
> + else
> + return ret;
> +}
> +
> static const struct cpu_ops riscv_cpu_ops = {
> .get_desc = riscv_cpu_get_desc,
> .get_info = riscv_cpu_get_info,
> @@ -116,6 +148,7 @@ U_BOOT_DRIVER(riscv_cpu) = {
> .id = UCLASS_CPU,
> .of_match = riscv_cpu_ids,
> .bind = riscv_cpu_bind,
> + .probe = riscv_cpu_probe,
> .ops = &riscv_cpu_ops,
> .flags = DM_FLAG_PRE_RELOC,
> };
>
--Sean
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 22/22] doc: sifive: fu540: Add description for RISC-V FU540 U-Boot SPL
2020-05-02 10:06 ` [PATCH v7 22/22] doc: sifive: fu540: Add description for RISC-V FU540 U-Boot SPL Pragnesh Patel
2020-05-02 12:55 ` Bin Meng
2020-05-02 16:22 ` Jagan Teki
@ 2020-05-03 4:34 ` Anup Patel
2020-05-03 6:13 ` Pragnesh Patel
2 siblings, 1 reply; 118+ messages in thread
From: Anup Patel @ 2020-05-03 4:34 UTC (permalink / raw)
To: u-boot
On Sat, May 2, 2020 at 3:41 PM Pragnesh Patel <pragnesh.patel@sifive.com> wrote:
>
> Add descriptions about U-Boot SPL feature and how to build and run
> from MMC.
>
> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
> ---
> doc/board/sifive/fu540.rst | 376 +++++++++++++++++++++++++++++++++++++
> 1 file changed, 376 insertions(+)
>
> diff --git a/doc/board/sifive/fu540.rst b/doc/board/sifive/fu540.rst
> index 1c3d4740f3..2911e3652e 100644
> --- a/doc/board/sifive/fu540.rst
> +++ b/doc/board/sifive/fu540.rst
> @@ -38,6 +38,9 @@ TODO:
> reg = <0x0 0x2000000 0x0 0xc0000>;
> };
>
> +Booting from MMC using FSBL
> +---------------------------
> +
> Building
> --------
>
> @@ -428,3 +431,376 @@ as well.
>
> Please press Enter to activate this console.
> / #
> +
> +Booting from MMC using U-Boot SPL
> +---------------------------------
> +
> +Building
> +--------
> +
> +Before building U-Boot SPL, OpenSBI must be built first. OpenSBI can be
> +cloned and built for FU540 as below:
> +
> +.. code-block:: console
> +
> + git clone https://github.com/riscv/opensbi.git
> + cd opensbi
> + make PLATFORM=generic FW_DYNAMIC=y
> +
> +Copy OpenSBI FW_DYNAMIC image
> +(build/platform/sifive/fu540/firmware/fw_dynamic.bin) into U-Boot
> +root directory
The path for fw_dynamic.bin should be:
build/platform/generic/firmware/fw_dynamic.bin
> +
> +.. code-block:: console
> +
> + cp build/platform/sifive/fu540/firmware/fw_dynamic.bin <u-boot-dir>
Same as above.
> +
> +Now build the U-Boot SPL and U-Boot proper
> +
> +.. code-block:: console
> +
> + cd <U-Boot-dir>
> + make sifive_fu540_defconfig
> + make
> +
> +This will generate spl/u-boot-spl.bin and FIT image (u-boot.itb)
> +
> +
> +Flashing
> +--------
> +
> +ZSBL loads the U-Boot SPL (u-boot-spl.bin) from a partition with GUID type
> +5B193300-FC78-40CD-8002-E86C45580B47
> +
> +U-Boot SPL expects a U-Boot FIT image (u-boot.itb) from a partition with GUID
> +type 2E54B353-1271-4842-806F-E436D6AF6985
> +
> +FIT image (u-boot.itb) is a combination of fw_dynamic.bin, u-boot-nodtb.bin and
> +device tree blob (hifive-unleashed-a00.dtb)
> +
> +Format the SD card (make sure the disk has GPT, otherwise use gdisk to switch)
> +
> +.. code-block:: none
> +
> + # sudo sgdisk --clear \
> + > --set-alignment=2 \
> + > --new=1:34:2081 --change-name=1:loader1 --typecode=1:5B193300-FC78-40CD-8002-E86C45580B47 \
> + > --new=2:2082:10273 --change-name=2:loader2 --typecode=2:2E54B353-1271-4842-806F-E436D6AF6985 \
> + > --new=3:10274: --change-name=3:rootfs --typecode=3:0FC63DAF-8483-4772-8E79-3D69D8477DE4 \
> + > /dev/sda
> +
> +Program the SD card
> +
> +.. code-block:: none
> +
> + sudo dd if=spl/u-boot-spl.bin of=/dev/sda seek=34
> + sudo dd if=u-boot.itb of=/dev/sda seek=2082
> +
> +Booting
> +-------
> +Once you plugin the sdcard and power up, you should see the U-Boot prompt.
> +
> +Sample boot log from HiFive Unleashed board
> +-------------------------------------------
> +
> +.. code-block:: none
> +
> + U-Boot SPL 2020.04-rc2-00109-g63efc7e07e-dirty (Apr 30 2020 - 13:52:36 +0530)
> + Trying to boot from MMC1
> +
> +
> + U-Boot 2020.04-rc2-00109-g63efc7e07e-dirty (Apr 30 2020 - 13:52:36 +0530)
> +
> + CPU: rv64imafdc
> + Model: SiFive HiFive Unleashed A00
> + DRAM: 8 GiB
> + MMC: spi at 10050000:mmc at 0: 0
> + In: serial at 10010000
> + Out: serial at 10010000
> + Err: serial at 10010000
> + Board serial number should not be 0 !!
> + Net:
> + Warning: ethernet at 10090000 (eth0) using random MAC address - 96:06:92:18:eb:04
> + eth0: ethernet at 10090000
> + Hit any key to stop autoboot: 0
> + => version
> + U-Boot 2020.04-rc2-00109-g63efc7e07e-dirty (Apr 30 2020 - 13:52:36 +0530)
> +
> + riscv64-unknown-linux-gnu-gcc (crosstool-NG 1.24.0.37-3f461da) 9.2.0
> + GNU ld (crosstool-NG 1.24.0.37-3f461da) 2.32
> + => mmc info
> + Device: spi at 10050000:mmc at 0
> + Manufacturer ID: 3
> + OEM: 5344
> + Name: SC16G
> + Bus Speed: 20000000
> + Mode: SD Legacy
> + Rd Block Len: 512
> + SD version 2.0
> + High Capacity: Yes
> + Capacity: 14.8 GiB
> + Bus Width: 1-bit
> + Erase Group Size: 512 Bytes
> + => mmc part
> +
> + Partition Map for MMC device 0 -- Partition Type: EFI
> +
> + Part Start LBA End LBA Name
> + Attributes
> + Type GUID
> + Partition GUID
> + 1 0x00000022 0x00000821 "loader1"
> + attrs: 0x0000000000000000
> + type: 5b193300-fc78-40cd-8002-e86c45580b47
> + guid: 66e2b5d2-74db-4df8-ad6f-694b3617f87f
> + 2 0x00000822 0x00002821 "loader2"
> + attrs: 0x0000000000000000
> + type: 2e54b353-1271-4842-806f-e436d6af6985
> + guid: 8befaeaf-bca0-435d-b002-e201f37c0a2f
> + 3 0x00002822 0x01dacbde "rootfs"
> + attrs: 0x0000000000000000
> + type: 0fc63daf-8483-4772-8e79-3d69d8477de4
> + type: linux
> + guid: 9faa81b6-39b1-4418-af5e-89c48f29c20d
> +
> +Now you can configure your networking, tftp server and use tftp boot method to
> +load uImage.
> +
> +.. code-block:: none
> +
> + => setenv serverip 192.168.0.103
> + => setenv serverip 192.168.0.102
> + => tftpboot 0x83000000 fit.itb
> + ethernet at 10090000: PHY present at 0
> + ethernet at 10090000: Starting autonegotiation...
> + ethernet at 10090000: Autonegotiation complete
> + ethernet at 10090000: link up, 100Mbps full-duplex (lpa: 0x4de1)
> + *** ERROR: `ipaddr' not set
> + => setenv serverip 192.168.0.103
> + => setenv ipaddr 192.168.0.102
> + => tftpboot 0x83000000 fit.itb
> + ethernet at 10090000: PHY present at 0
> + ethernet at 10090000: Starting autonegotiation...
> + ethernet at 10090000: Autonegotiation complete
> + ethernet at 10090000: link up, 100Mbps full-duplex (lpa: 0x4de1)
> + Using ethernet at 10090000 device
> + TFTP from server 192.168.0.103; our IP address is 192.168.0.102
> + Filename 'fit.itb'.
> + Load address: 0x83000000
> + Loading: #################################################################
> + #################################################################
> + #################################################################
> + #################################################################
> + #################################################################
> + #################################################################
> + #################################################################
> + #################################################################
> + #################################################################
> + #################################################################
> + #################################################################
> + #################################################################
> + #################################################################
> + #################################################################
> + #################################################################
> + #################################################################
> + #################################################################
> + #######################################################
> + 4.2 MiB/s
> + done
> + Bytes transferred = 14254183 (d98067 hex)
> + => bootm 0x83000000
> + ## Loading kernel from FIT Image at 83000000 ...
> + Using 'config-1' configuration
> + Trying 'kernel at 1' kernel subimage
> + Description: Linux kernel
> + Type: Kernel Image
> + Compression: uncompressed
> + Data Start: 0x830000d8
> + Data Size: 9676752 Bytes = 9.2 MiB
> + Architecture: RISC-V
> + OS: Linux
> + Load Address: 0x80200000
> + Entry Point: 0x80200000
> + Verifying Hash Integrity ... OK
> + ## Loading ramdisk from FIT Image at 83000000 ...
> + Using 'config-1' configuration
> + Trying 'ramdisk at 1' ramdisk subimage
> + Description: ramdisk
> + Type: RAMDisk Image
> + Compression: gzip compressed
> + Data Start: 0x8393c490
> + Data Size: 4568674 Bytes = 4.4 MiB
> + Architecture: RISC-V
> + OS: Linux
> + Load Address: 0x82000000
> + Entry Point: unavailable
> + Verifying Hash Integrity ... OK
> + Loading ramdisk from 0x8393c490 to 0x82000000
> + WARNING: 'compression' nodes for ramdisks are deprecated, please fix your .its file!
> + ## Loading fdt from FIT Image at 83000000 ...
> + Using 'config-1' configuration
> + Trying 'fdt at 1' fdt subimage
> + Description: unavailable
> + Type: Flat Device Tree
> + Compression: uncompressed
> + Data Start: 0x8393a934
> + Data Size: 6889 Bytes = 6.7 KiB
> + Architecture: RISC-V
> + Verifying Hash Integrity ... OK
> + Booting using the fdt blob at 0x8393a934
> + Loading Kernel Image
> + Using Device Tree in place at 000000008393a934, end 000000008393f41c
> +
> + Starting kernel ...
> +
> + [ 0.000000] OF: fdt: Ignoring memory range 0x80000000 - 0x80200000
> + [ 0.000000] Linux version 5.6.0-rc3-00026-g63623fd44972 (pragneshp at sachinj2-OptiPlex-7010) (gcc version 9.2.0 (crosstool-NG 1.24.0.37-3f461da)) #3 SMP Tue Feb 25 14:59:12 IST 2020
> + [ 0.000000] Initial ramdisk at: 0x(____ptrval____) (4568674 bytes)
> + [ 0.000000] Zone ranges:
> + [ 0.000000] DMA32 [mem 0x0000000080200000-0x00000000ffffffff]
> + [ 0.000000] Normal [mem 0x0000000100000000-0x000000027fffffff]
> + [ 0.000000] Movable zone start for each node
> + [ 0.000000] Early memory node ranges
> + [ 0.000000] node 0: [mem 0x0000000080200000-0x000000027fffffff]
> + [ 0.000000] Initmem setup node 0 [mem 0x0000000080200000-0x000000027fffffff]
> + [ 0.000000] software IO TLB: mapped [mem 0xfbfff000-0xfffff000] (64MB)
> + [ 0.000000] CPU with hartid=0 is not available
> + [ 0.000000] CPU with hartid=0 is not available
> + [ 0.000000] elf_hwcap is 0x112d
> + [ 0.000000] percpu: Embedded 17 pages/cpu s31848 r8192 d29592 u69632
> + [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 2067975
> + [ 0.000000] Kernel command line:
> + [ 0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
> + [ 0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
> + [ 0.000000] Sorting __ex_table...
> + [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
> + [ 0.000000] Memory: 8179388K/8386560K available (6288K kernel code, 458K rwdata, 2135K rodata, 239K init, 311K bss, 207172K reserved, 0K cma-reserved)
> + [ 0.000000] Virtual kernel memory layout:
> + [ 0.000000] fixmap : 0xffffffcefee00000 - 0xffffffceff000000 (2048 kB)
> + [ 0.000000] pci io : 0xffffffceff000000 - 0xffffffcf00000000 ( 16 MB)
> + [ 0.000000] vmemmap : 0xffffffcf00000000 - 0xffffffcfffffffff (4095 MB)
> + [ 0.000000] vmalloc : 0xffffffd000000000 - 0xffffffdfffffffff (65535 MB)
> + [ 0.000000] lowmem : 0xffffffe000000000 - 0xffffffe1ffe00000 (8190 MB)
> + [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
> + [ 0.000000] rcu: Hierarchical RCU implementation.
> + [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
> + [ 0.000000] rcu: RCU debug extended QS entry/exit.
> + [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
> + [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
> + [ 0.000000] NR_IRQS: 0, nr_irqs: 0, preallocated irqs: 0
> + [ 0.000000] plic: mapped 53 interrupts with 4 handlers for 9 contexts.
> + [ 0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [1]
> + [ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 3526361616960 ns
> + [ 0.000007] sched_clock: 64 bits at 1000kHz, resolution 1000ns, wraps every 2199023255500ns
> + [ 0.000159] Console: colour dummy device 80x25
> + [ 0.001130] printk: console [tty0] enabled
> + [ 0.001193] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=4000)
> + [ 0.001259] pid_max: default: 32768 minimum: 301
> + [ 0.001798] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
> + [ 0.002191] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
> + [ 0.004308] rcu: Hierarchical SRCU implementation.
> + [ 0.004981] smp: Bringing up secondary CPUs ...
> + [ 1.024833] CPU1: failed to come online
> + [ 2.049612] CPU2: failed to come online
> + [ 3.074387] CPU3: failed to come online
> + [ 3.074453] smp: Brought up 1 node, 1 CPU
> + [ 3.075612] devtmpfs: initialized
> + [ 3.077517] random: get_random_u32 called from bucket_table_alloc.isra.0+0x4e/0x15e with crng_init=0
> + [ 3.077774] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
> + [ 3.077899] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
> + [ 3.078689] NET: Registered protocol family 16
> + [ 3.094523] vgaarb: loaded
> + [ 3.094914] SCSI subsystem initialized
> + [ 3.095364] usbcore: registered new interface driver usbfs
> + [ 3.095444] usbcore: registered new interface driver hub
> + [ 3.095533] usbcore: registered new device driver usb
> + [ 3.096290] clocksource: Switched to clocksource riscv_clocksource
> + [ 3.103494] NET: Registered protocol family 2
> + [ 3.104158] tcp_listen_portaddr_hash hash table entries: 4096 (order: 5, 163840 bytes, linear)
> + [ 3.104806] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear)
> + [ 3.106882] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes, linear)
> + [ 3.114045] TCP: Hash tables configured (established 65536 bind 65536)
> + [ 3.114589] UDP hash table entries: 4096 (order: 6, 393216 bytes, linear)
> + [ 3.115949] UDP-Lite hash table entries: 4096 (order: 6, 393216 bytes, linear)
> + [ 3.117578] NET: Registered protocol family 1
> + [ 3.118255] RPC: Registered named UNIX socket transport module.
> + [ 3.118295] RPC: Registered udp transport module.
> + [ 3.118328] RPC: Registered tcp transport module.
> + [ 3.118360] RPC: Registered tcp NFSv4.1 backchannel transport module.
> + [ 3.118397] PCI: CLS 0 bytes, default 64
> + [ 3.118621] Unpacking initramfs...
> + [ 3.475555] Freeing initrd memory: 4460K
> + [ 3.476511] workingset: timestamp_bits=62 max_order=21 bucket_order=0
> + [ 3.485899] NFS: Registering the id_resolver key type
> + [ 3.485961] Key type id_resolver registered
> + [ 3.485994] Key type id_legacy registered
> + [ 3.486037] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
> + [ 3.486236] 9p: Installing v9fs 9p2000 file system support
> + [ 3.486651] NET: Registered protocol family 38
> + [ 3.486729] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
> + [ 3.486788] io scheduler mq-deadline registered
> + [ 3.486822] io scheduler kyber registered
> + [ 3.528973] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
> + [ 3.530114] 10010000.serial: ttySIF0 at MMIO 0x10010000 (irq = 1, base_baud = 0) is a SiFive UART v0
> + [ 4.061558] printk: console [ttySIF0] enabled
> + [ 4.066211] 10011000.serial: ttySIF1 at MMIO 0x10011000 (irq = 10, base_baud = 0) is a SiFive UART v0
> + [ 4.075620] [drm] radeon kernel modesetting enabled.
> + [ 4.092998] loop: module loaded
> + [ 4.096007] sifive_spi 10040000.spi: mapped; irq=12, cs=1
> + [ 4.101380] sifive_spi 10050000.spi: mapped; irq=13, cs=1
> + [ 4.107129] libphy: Fixed MDIO Bus: probed
> + [ 4.111232] macb 10090000.ethernet: Registered clk switch 'sifive-gemgxl-mgmt'
> + [ 4.117841] macb 10090000.ethernet: GEM doesn't support hardware ptp.
> + [ 4.124654] libphy: MACB_mii_bus: probed
> + [ 4.133149] macb 10090000.ethernet eth0: Cadence GEM rev 0x10070109 at 0x10090000 irq 14 (86:5d:6f:58:d6:3d)
> + [ 4.142400] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
> + [ 4.148053] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
> + [ 4.154051] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
> + [ 4.160470] ehci-pci: EHCI PCI platform driver
> + [ 4.164930] ehci-platform: EHCI generic platform driver
> + [ 4.170185] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
> + [ 4.176284] ohci-pci: OHCI PCI platform driver
> + [ 4.180736] ohci-platform: OHCI generic platform driver
> + [ 4.186226] usbcore: registered new interface driver uas
> + [ 4.191257] usbcore: registered new interface driver usb-storage
> + [ 4.197392] mousedev: PS/2 mouse device common for all mice
> + [ 4.228311] mmc_spi spi1.0: SD/MMC host mmc0, no DMA, no WP, no poweroff, cd polling
> + [ 4.235528] usbcore: registered new interface driver usbhid
> + [ 4.240870] usbhid: USB HID core driver
> + [ 4.245515] NET: Registered protocol family 10
> + [ 4.250603] Segment Routing with IPv6
> + [ 4.253602] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
> + [ 4.259978] NET: Registered protocol family 17
> + [ 4.264098] 9pnet: Installing 9P2000 support
> + [ 4.268159] Key type dns_resolver registered
> + [ 4.279265] Freeing unused kernel memory: 236K
> + [ 4.282989] This architecture does not have kernel memory protection.
> + [ 4.289390] Run /init as init process
> + Starting syslogd: OK
> + Starting klogd: OK
> + Starting mdev...
> + /etc/init.d/S10mdev: line 9: can't create /proc/sys/kernel/hotplug: nonexistent directory
> + [ 4.354461] mmc0: host does not support reading read-only switch, assuming write-enable
> + [ 4.361778] mmc0: new SDHC card on SPI
> + [ 4.381184] mmcblk0: mmc0:0000 SC16G 14.8 GiB
> + [ 4.424975] mmcblk0: p1 p2 p3
> + modprobe: can't change directory to '/lib/modules': No such file or directory
> + Initializing random number generator... [ 5.041362] random: dd: uninitialized urandom read (512 bytes read)
> + done.
> + Starting network: [ 5.240580] macb 10090000.ethernet eth0: PHY [10090000.ethernet-ffffffff:00] driver [Microsemi VSC8541 SyncE] (irq=POLL)
> + [ 5.250752] macb 10090000.ethernet eth0: configuring for phy/gmii link mode
> + udhcpc: started, v1.29.3
> + udhcpc: sending discover
> + [ 7.301682] macb 10090000.ethernet eth0: Link is Up - 100Mbps/Full - flow control tx
> + [ 7.308726] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
> + udhcpc: sending discover
> + udhcpc: sending discover
> + udhcpc: no lease, failing
> + FAIL
> + Starting dropbear sshd: [ 14.309152] random: dropbear: uninitialized urandom read (32 bytes read)
> + OK
> +
> + Welcome to Buildroot
> + buildroot login: root
> + Password:
> + #
> --
> 2.17.1
>
Otherwise looks good to me.
Reviewed-by: Anup Patel <anup@brainfault.org>
Regards,
Anup
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 21/22] doc: sifive: fu540: Add description for OpenSBI generic platform
2020-05-02 15:27 ` Bin Meng
2020-05-02 15:29 ` Pragnesh Patel
@ 2020-05-03 4:36 ` Anup Patel
1 sibling, 0 replies; 118+ messages in thread
From: Anup Patel @ 2020-05-03 4:36 UTC (permalink / raw)
To: u-boot
On Sat, May 2, 2020 at 8:57 PM Bin Meng <bmeng.cn@gmail.com> wrote:
>
> Hi Pragnesh,
>
> On Sat, May 2, 2020 at 11:22 PM Pragnesh Patel
> <pragnesh.patel@sifive.com> wrote:
> >
> >
> > Hi Bin,
> >
> > >-----Original Message-----
> > >From: Bin Meng <bmeng.cn@gmail.com>
> > >Sent: 02 May 2020 20:47
> > >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> > >Cc: U-Boot Mailing List <u-boot@lists.denx.de>; Atish Patra
> > ><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Paul
> > >Walmsley <paul.walmsley@sifive.com>; Jagan Teki
> > ><jagan@amarulasolutions.com>; Troy Benjegerdes
> > ><troy.benjegerdes@sifive.com>; Anup Patel <anup.patel@wdc.com>; Sagar
> > >Kadam <sagar.kadam@sifive.com>; Rick Chen <rick@andestech.com>
> > >Subject: Re: [PATCH v7 21/22] doc: sifive: fu540: Add description for OpenSBI
> > >generic platform
> > >
> > >[External Email] Do not click links or attachments unless you recognize the
> > >sender and know the content is safe
> > >
> > >Hi Pragnesh,
> > >
> > >On Sat, May 2, 2020 at 10:30 PM Pragnesh Patel <pragnesh.patel@sifive.com>
> > >wrote:
> > >>
> > >> Hi Bin,
> > >>
> > >> >-----Original Message-----
> > >> >From: Bin Meng <bmeng.cn@gmail.com>
> > >> >Sent: 02 May 2020 18:26
> > >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> > >> >Cc: U-Boot Mailing List <u-boot@lists.denx.de>; Atish Patra
> > >> ><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>;
> > >> >Paul Walmsley <paul.walmsley@sifive.com>; Jagan Teki
> > >> ><jagan@amarulasolutions.com>; Troy Benjegerdes
> > >> ><troy.benjegerdes@sifive.com>; Anup Patel <anup.patel@wdc.com>; Sagar
> > >> >Kadam <sagar.kadam@sifive.com>; Rick Chen <rick@andestech.com>
> > >> >Subject: Re: [PATCH v7 21/22] doc: sifive: fu540: Add description for
> > >> >OpenSBI generic platform
> > >> >
> > >> >[External Email] Do not click links or attachments unless you
> > >> >recognize the sender and know the content is safe
> > >> >
> > >> >Hi Pragnesh,
> > >> >
> > >> >On Sat, May 2, 2020 at 6:09 PM Pragnesh Patel
> > >> ><pragnesh.patel@sifive.com>
> > >> >wrote:
> > >> >>
> > >> >> OpenSBI generic platform support provides platform specific
> > >> >> functionality based on the FDT passed by previous booting stage.
> > >> >>
> > >> >> depends on OpenSBI commit:
> > >> >> platform: Add generic FDT based platform support
> > >> >> (sha1: f1aa9e54e00006ae70aeac638d5b75093520f65d)
> > >> >>
> > >> >> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
> > >> >> ---
> > >> >> doc/board/sifive/fu540.rst | 19 +++++++++++++------
> > >> >> 1 file changed, 13 insertions(+), 6 deletions(-)
> > >> >>
> > >> >> diff --git a/doc/board/sifive/fu540.rst
> > >> >> b/doc/board/sifive/fu540.rst index 610ba87074..1c3d4740f3 100644
> > >> >> --- a/doc/board/sifive/fu540.rst
> > >> >> +++ b/doc/board/sifive/fu540.rst
> > >> >> @@ -22,14 +22,21 @@ The support for following drivers are already
> > >> >enabled:
> > >> >>
> > >> >> TODO:
> > >> >>
> > >> >> -1. U-Boot expects the serial console device entry to be present
> > >> >> under
> > >> >/chosen
> > >> >> - DT node. Without a serial console U-Boot will panic. Example:
> > >> >> +1. The DTB passed by U-Boot SPL or FSBL to OpenSBI should have CLINT
> > >> >> + DT node and the "/chosen" DT node should have "stdout-path" DT
> > >> >> + property.
> > >> >>
> > >> >> .. code-block:: none
> > >> >>
> > >> >> - chosen {
> > >> >> - stdout-path = "/soc/serial at 10010000:115200";
> > >> >> - };
> > >> >> + chosen {
> > >> >> + stdout-path = "/soc/serial at 10010000:115200";
> > >> >> + };
> > >> >> +
> > >> >> + clint at 2000000 {
> > >> >> + compatible = "riscv,clint0";
> > >> >> + interrupts-extended = <&cpu0_intc 3 &cpu0_intc 7
> > >> >> + &cpu1_intc 3
> > >> >&cpu1_intc 7 &cpu2_intc 3 &cpu2_intc 7 &cpu3_intc 3 &cpu3_intc 7
> > >> >&cpu4_intc 3 &cpu4_intc 7>;
> > >> >> + reg = <0x0 0x2000000 0x0 0xc0000>;
> > >> >> + };
> > >> >
> > >> >Can we update the U-Boot dtsi to include the changes?
> > >>
> > >> Can you please clarify which dtsi fu540-c000-u-boot.dtsi or fu540-c000.dtsi ?
> > >>
> > >> I have already added clint DT node in "arch/riscv/dts/fu540-c000-u-
> > >boot.dtsi"
> > >
> > >I thought we did not add this. So maybe we can remove this information
> > >completely from the doc?
> >
> > OpenSBI expect a "chosen DT node and clint DT node" from prior stage bootloader DTB, So i think
> > it's fine to add clint as a reference here.
> >
> > Any suggestions are welcome.
> >
>
> Maybe such information should be put in the OpenSBI generic platform
> doc, but not U-Boot doc ??
Sure, I will add more details to OpenSBI generic platform documentation.
Regards,
Anup
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 22/22] doc: sifive: fu540: Add description for RISC-V FU540 U-Boot SPL
2020-05-03 4:34 ` Anup Patel
@ 2020-05-03 6:13 ` Pragnesh Patel
0 siblings, 0 replies; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-03 6:13 UTC (permalink / raw)
To: u-boot
Hi Anup,
>-----Original Message-----
>From: Anup Patel <anup@brainfault.org>
>Sent: 03 May 2020 10:04
>To: Pragnesh Patel <pragnesh.patel@sifive.com>
>Cc: U-Boot Mailing List <u-boot@lists.denx.de>; Atish Patra
><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Bin
>Meng <bmeng.cn@gmail.com>; Paul Walmsley <paul.walmsley@sifive.com>;
>Jagan Teki <jagan@amarulasolutions.com>; Troy Benjegerdes
><troy.benjegerdes@sifive.com>; Anup Patel <anup.patel@wdc.com>; Sagar
>Kadam <sagar.kadam@sifive.com>; Rick Chen <rick@andestech.com>; Joe
>Hershberger <joe.hershberger@ni.com>
>Subject: Re: [PATCH v7 22/22] doc: sifive: fu540: Add description for RISC-V
>FU540 U-Boot SPL
>
>[External Email] Do not click links or attachments unless you recognize the
>sender and know the content is safe
>
>On Sat, May 2, 2020 at 3:41 PM Pragnesh Patel <pragnesh.patel@sifive.com>
>wrote:
>>
>> Add descriptions about U-Boot SPL feature and how to build and run
>> from MMC.
>>
>> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
>> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
>> ---
>> doc/board/sifive/fu540.rst | 376
>> +++++++++++++++++++++++++++++++++++++
>> 1 file changed, 376 insertions(+)
>>
>> diff --git a/doc/board/sifive/fu540.rst b/doc/board/sifive/fu540.rst
>> index 1c3d4740f3..2911e3652e 100644
>> --- a/doc/board/sifive/fu540.rst
>> +++ b/doc/board/sifive/fu540.rst
>> @@ -38,6 +38,9 @@ TODO:
>> reg = <0x0 0x2000000 0x0 0xc0000>;
>> };
>>
>> +Booting from MMC using FSBL
>> +---------------------------
>> +
>> Building
>> --------
>>
>> @@ -428,3 +431,376 @@ as well.
>>
>> Please press Enter to activate this console.
>> / #
>> +
>> +Booting from MMC using U-Boot SPL
>> +---------------------------------
>> +
>> +Building
>> +--------
>> +
>> +Before building U-Boot SPL, OpenSBI must be built first. OpenSBI can
>> +be cloned and built for FU540 as below:
>> +
>> +.. code-block:: console
>> +
>> + git clone https://github.com/riscv/opensbi.git
>> + cd opensbi
>> + make PLATFORM=generic FW_DYNAMIC=y
>> +
>> +Copy OpenSBI FW_DYNAMIC image
>> +(build/platform/sifive/fu540/firmware/fw_dynamic.bin) into U-Boot
>> +root directory
>
>The path for fw_dynamic.bin should be:
>build/platform/generic/firmware/fw_dynamic.bin
Good catch, will update in v8.
>
>> +
>> +.. code-block:: console
>> +
>> + cp build/platform/sifive/fu540/firmware/fw_dynamic.bin
>> + <u-boot-dir>
>
>Same as above.
Will update in v8.
>
>> +
>> +Now build the U-Boot SPL and U-Boot proper
>> +
>> +.. code-block:: console
>> +
>> + cd <U-Boot-dir>
>> + make sifive_fu540_defconfig
>> + make
>> +
>> +This will generate spl/u-boot-spl.bin and FIT image (u-boot.itb)
>> +
>> +
>> +Flashing
>> +--------
>> +
>> +ZSBL loads the U-Boot SPL (u-boot-spl.bin) from a partition with GUID
>> +type
>> +5B193300-FC78-40CD-8002-E86C45580B47
>> +
>> +U-Boot SPL expects a U-Boot FIT image (u-boot.itb) from a partition
>> +with GUID type 2E54B353-1271-4842-806F-E436D6AF6985
>> +
>> +FIT image (u-boot.itb) is a combination of fw_dynamic.bin,
>> +u-boot-nodtb.bin and device tree blob (hifive-unleashed-a00.dtb)
>> +
>> +Format the SD card (make sure the disk has GPT, otherwise use gdisk
>> +to switch)
>> +
>> +.. code-block:: none
>> +
>> + # sudo sgdisk --clear \
>> + > --set-alignment=2 \
>> + > --new=1:34:2081 --change-name=1:loader1 --typecode=1:5B193300-
>FC78-40CD-8002-E86C45580B47 \
>> + > --new=2:2082:10273 --change-name=2:loader2 --
>typecode=2:2E54B353-1271-4842-806F-E436D6AF6985 \
>> + > --new=3:10274: --change-name=3:rootfs --typecode=3:0FC63DAF-
>8483-4772-8E79-3D69D8477DE4 \
>> + > /dev/sda
>> +
>> +Program the SD card
>> +
>> +.. code-block:: none
>> +
>> + sudo dd if=spl/u-boot-spl.bin of=/dev/sda seek=34
>> + sudo dd if=u-boot.itb of=/dev/sda seek=2082
>> +
>> +Booting
>> +-------
>> +Once you plugin the sdcard and power up, you should see the U-Boot
>prompt.
>> +
>> +Sample boot log from HiFive Unleashed board
>> +-------------------------------------------
>> +
>> +.. code-block:: none
>> +
>> + U-Boot SPL 2020.04-rc2-00109-g63efc7e07e-dirty (Apr 30 2020 -
>13:52:36 +0530)
>> + Trying to boot from MMC1
>> +
>> +
>> + U-Boot 2020.04-rc2-00109-g63efc7e07e-dirty (Apr 30 2020 -
>> + 13:52:36 +0530)
>> +
>> + CPU: rv64imafdc
>> + Model: SiFive HiFive Unleashed A00
>> + DRAM: 8 GiB
>> + MMC: spi at 10050000:mmc at 0: 0
>> + In: serial at 10010000
>> + Out: serial at 10010000
>> + Err: serial at 10010000
>> + Board serial number should not be 0 !!
>> + Net:
>> + Warning: ethernet at 10090000 (eth0) using random MAC address -
>96:06:92:18:eb:04
>> + eth0: ethernet at 10090000
>> + Hit any key to stop autoboot: 0
>> + => version
>> + U-Boot 2020.04-rc2-00109-g63efc7e07e-dirty (Apr 30 2020 -
>> + 13:52:36 +0530)
>> +
>> + riscv64-unknown-linux-gnu-gcc (crosstool-NG 1.24.0.37-3f461da) 9.2.0
>> + GNU ld (crosstool-NG 1.24.0.37-3f461da) 2.32
>> + => mmc info
>> + Device: spi at 10050000:mmc at 0
>> + Manufacturer ID: 3
>> + OEM: 5344
>> + Name: SC16G
>> + Bus Speed: 20000000
>> + Mode: SD Legacy
>> + Rd Block Len: 512
>> + SD version 2.0
>> + High Capacity: Yes
>> + Capacity: 14.8 GiB
>> + Bus Width: 1-bit
>> + Erase Group Size: 512 Bytes
>> + => mmc part
>> +
>> + Partition Map for MMC device 0 -- Partition Type: EFI
>> +
>> + Part Start LBA End LBA Name
>> + Attributes
>> + Type GUID
>> + Partition GUID
>> + 1 0x00000022 0x00000821 "loader1"
>> + attrs: 0x0000000000000000
>> + type: 5b193300-fc78-40cd-8002-e86c45580b47
>> + guid: 66e2b5d2-74db-4df8-ad6f-694b3617f87f
>> + 2 0x00000822 0x00002821 "loader2"
>> + attrs: 0x0000000000000000
>> + type: 2e54b353-1271-4842-806f-e436d6af6985
>> + guid: 8befaeaf-bca0-435d-b002-e201f37c0a2f
>> + 3 0x00002822 0x01dacbde "rootfs"
>> + attrs: 0x0000000000000000
>> + type: 0fc63daf-8483-4772-8e79-3d69d8477de4
>> + type: linux
>> + guid: 9faa81b6-39b1-4418-af5e-89c48f29c20d
>> +
>> +Now you can configure your networking, tftp server and use tftp boot
>> +method to load uImage.
>> +
>> +.. code-block:: none
>> +
>> + => setenv serverip 192.168.0.103
>> + => setenv serverip 192.168.0.102
>> + => tftpboot 0x83000000 fit.itb
>> + ethernet at 10090000: PHY present at 0
>> + ethernet at 10090000: Starting autonegotiation...
>> + ethernet at 10090000: Autonegotiation complete
>> + ethernet at 10090000: link up, 100Mbps full-duplex (lpa: 0x4de1)
>> + *** ERROR: `ipaddr' not set
>> + => setenv serverip 192.168.0.103
>> + => setenv ipaddr 192.168.0.102
>> + => tftpboot 0x83000000 fit.itb
>> + ethernet at 10090000: PHY present at 0
>> + ethernet at 10090000: Starting autonegotiation...
>> + ethernet at 10090000: Autonegotiation complete
>> + ethernet at 10090000: link up, 100Mbps full-duplex (lpa: 0x4de1)
>> + Using ethernet at 10090000 device
>> + TFTP from server 192.168.0.103; our IP address is 192.168.0.102
>> + Filename 'fit.itb'.
>> + Load address: 0x83000000
>> + Loading:
>#################################################################
>> +
>#################################################################
>> +
>#################################################################
>> +
>#################################################################
>> +
>#################################################################
>> +
>#################################################################
>> +
>#################################################################
>> +
>#################################################################
>> +
>#################################################################
>> +
>#################################################################
>> +
>#################################################################
>> +
>#################################################################
>> +
>#################################################################
>> +
>#################################################################
>> +
>#################################################################
>> +
>#################################################################
>> +
>#################################################################
>> + #######################################################
>> + 4.2 MiB/s
>> + done
>> + Bytes transferred = 14254183 (d98067 hex)
>> + => bootm 0x83000000
>> + ## Loading kernel from FIT Image at 83000000 ...
>> + Using 'config-1' configuration
>> + Trying 'kernel at 1' kernel subimage
>> + Description: Linux kernel
>> + Type: Kernel Image
>> + Compression: uncompressed
>> + Data Start: 0x830000d8
>> + Data Size: 9676752 Bytes = 9.2 MiB
>> + Architecture: RISC-V
>> + OS: Linux
>> + Load Address: 0x80200000
>> + Entry Point: 0x80200000
>> + Verifying Hash Integrity ... OK
>> + ## Loading ramdisk from FIT Image at 83000000 ...
>> + Using 'config-1' configuration
>> + Trying 'ramdisk at 1' ramdisk subimage
>> + Description: ramdisk
>> + Type: RAMDisk Image
>> + Compression: gzip compressed
>> + Data Start: 0x8393c490
>> + Data Size: 4568674 Bytes = 4.4 MiB
>> + Architecture: RISC-V
>> + OS: Linux
>> + Load Address: 0x82000000
>> + Entry Point: unavailable
>> + Verifying Hash Integrity ... OK
>> + Loading ramdisk from 0x8393c490 to 0x82000000
>> + WARNING: 'compression' nodes for ramdisks are deprecated, please fix
>your .its file!
>> + ## Loading fdt from FIT Image at 83000000 ...
>> + Using 'config-1' configuration
>> + Trying 'fdt at 1' fdt subimage
>> + Description: unavailable
>> + Type: Flat Device Tree
>> + Compression: uncompressed
>> + Data Start: 0x8393a934
>> + Data Size: 6889 Bytes = 6.7 KiB
>> + Architecture: RISC-V
>> + Verifying Hash Integrity ... OK
>> + Booting using the fdt blob at 0x8393a934
>> + Loading Kernel Image
>> + Using Device Tree in place at 000000008393a934, end
>> + 000000008393f41c
>> +
>> + Starting kernel ...
>> +
>> + [ 0.000000] OF: fdt: Ignoring memory range 0x80000000 - 0x80200000
>> + [ 0.000000] Linux version 5.6.0-rc3-00026-g63623fd44972
>(pragneshp at sachinj2-OptiPlex-7010) (gcc version 9.2.0 (crosstool-NG
>1.24.0.37-3f461da)) #3 SMP Tue Feb 25 14:59:12 IST 2020
>> + [ 0.000000] Initial ramdisk at: 0x(____ptrval____) (4568674 bytes)
>> + [ 0.000000] Zone ranges:
>> + [ 0.000000] DMA32 [mem 0x0000000080200000-
>0x00000000ffffffff]
>> + [ 0.000000] Normal [mem 0x0000000100000000-
>0x000000027fffffff]
>> + [ 0.000000] Movable zone start for each node
>> + [ 0.000000] Early memory node ranges
>> + [ 0.000000] node 0: [mem 0x0000000080200000-
>0x000000027fffffff]
>> + [ 0.000000] Initmem setup node 0 [mem 0x0000000080200000-
>0x000000027fffffff]
>> + [ 0.000000] software IO TLB: mapped [mem 0xfbfff000-0xfffff000]
>(64MB)
>> + [ 0.000000] CPU with hartid=0 is not available
>> + [ 0.000000] CPU with hartid=0 is not available
>> + [ 0.000000] elf_hwcap is 0x112d
>> + [ 0.000000] percpu: Embedded 17 pages/cpu s31848 r8192 d29592
>u69632
>> + [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages:
>2067975
>> + [ 0.000000] Kernel command line:
>> + [ 0.000000] Dentry cache hash table entries: 1048576 (order: 11,
>8388608 bytes, linear)
>> + [ 0.000000] Inode-cache hash table entries: 524288 (order: 10,
>4194304 bytes, linear)
>> + [ 0.000000] Sorting __ex_table...
>> + [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
>> + [ 0.000000] Memory: 8179388K/8386560K available (6288K kernel
>code, 458K rwdata, 2135K rodata, 239K init, 311K bss, 207172K reserved, 0K
>cma-reserved)
>> + [ 0.000000] Virtual kernel memory layout:
>> + [ 0.000000] fixmap : 0xffffffcefee00000 - 0xffffffceff000000 (2048
>kB)
>> + [ 0.000000] pci io : 0xffffffceff000000 - 0xffffffcf00000000 ( 16
>MB)
>> + [ 0.000000] vmemmap : 0xffffffcf00000000 - 0xffffffcfffffffff (4095
>MB)
>> + [ 0.000000] vmalloc : 0xffffffd000000000 - 0xffffffdfffffffff (65535
>MB)
>> + [ 0.000000] lowmem : 0xffffffe000000000 - 0xffffffe1ffe00000
>(8190 MB)
>> + [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4,
>Nodes=1
>> + [ 0.000000] rcu: Hierarchical RCU implementation.
>> + [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to
>nr_cpu_ids=4.
>> + [ 0.000000] rcu: RCU debug extended QS entry/exit.
>> + [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is
>25 jiffies.
>> + [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16,
>nr_cpu_ids=4
>> + [ 0.000000] NR_IRQS: 0, nr_irqs: 0, preallocated irqs: 0
>> + [ 0.000000] plic: mapped 53 interrupts with 4 handlers for 9 contexts.
>> + [ 0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0]
>hartid [1]
>> + [ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff
>max_cycles: 0x1d854df40, max_idle_ns: 3526361616960 ns
>> + [ 0.000007] sched_clock: 64 bits at 1000kHz, resolution 1000ns, wraps
>every 2199023255500ns
>> + [ 0.000159] Console: colour dummy device 80x25
>> + [ 0.001130] printk: console [tty0] enabled
>> + [ 0.001193] Calibrating delay loop (skipped), value calculated using
>timer frequency.. 2.00 BogoMIPS (lpj=4000)
>> + [ 0.001259] pid_max: default: 32768 minimum: 301
>> + [ 0.001798] Mount-cache hash table entries: 16384 (order: 5, 131072
>bytes, linear)
>> + [ 0.002191] Mountpoint-cache hash table entries: 16384 (order: 5,
>131072 bytes, linear)
>> + [ 0.004308] rcu: Hierarchical SRCU implementation.
>> + [ 0.004981] smp: Bringing up secondary CPUs ...
>> + [ 1.024833] CPU1: failed to come online
>> + [ 2.049612] CPU2: failed to come online
>> + [ 3.074387] CPU3: failed to come online
>> + [ 3.074453] smp: Brought up 1 node, 1 CPU
>> + [ 3.075612] devtmpfs: initialized
>> + [ 3.077517] random: get_random_u32 called from
>bucket_table_alloc.isra.0+0x4e/0x15e with crng_init=0
>> + [ 3.077774] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff,
>max_idle_ns: 7645041785100000 ns
>> + [ 3.077899] futex hash table entries: 1024 (order: 4, 65536 bytes,
>linear)
>> + [ 3.078689] NET: Registered protocol family 16
>> + [ 3.094523] vgaarb: loaded
>> + [ 3.094914] SCSI subsystem initialized
>> + [ 3.095364] usbcore: registered new interface driver usbfs
>> + [ 3.095444] usbcore: registered new interface driver hub
>> + [ 3.095533] usbcore: registered new device driver usb
>> + [ 3.096290] clocksource: Switched to clocksource riscv_clocksource
>> + [ 3.103494] NET: Registered protocol family 2
>> + [ 3.104158] tcp_listen_portaddr_hash hash table entries: 4096 (order:
>5, 163840 bytes, linear)
>> + [ 3.104806] TCP established hash table entries: 65536 (order: 7,
>524288 bytes, linear)
>> + [ 3.106882] TCP bind hash table entries: 65536 (order: 9, 2097152
>bytes, linear)
>> + [ 3.114045] TCP: Hash tables configured (established 65536 bind
>65536)
>> + [ 3.114589] UDP hash table entries: 4096 (order: 6, 393216 bytes,
>linear)
>> + [ 3.115949] UDP-Lite hash table entries: 4096 (order: 6, 393216 bytes,
>linear)
>> + [ 3.117578] NET: Registered protocol family 1
>> + [ 3.118255] RPC: Registered named UNIX socket transport module.
>> + [ 3.118295] RPC: Registered udp transport module.
>> + [ 3.118328] RPC: Registered tcp transport module.
>> + [ 3.118360] RPC: Registered tcp NFSv4.1 backchannel transport
>module.
>> + [ 3.118397] PCI: CLS 0 bytes, default 64
>> + [ 3.118621] Unpacking initramfs...
>> + [ 3.475555] Freeing initrd memory: 4460K
>> + [ 3.476511] workingset: timestamp_bits=62 max_order=21
>bucket_order=0
>> + [ 3.485899] NFS: Registering the id_resolver key type
>> + [ 3.485961] Key type id_resolver registered
>> + [ 3.485994] Key type id_legacy registered
>> + [ 3.486037] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
>> + [ 3.486236] 9p: Installing v9fs 9p2000 file system support
>> + [ 3.486651] NET: Registered protocol family 38
>> + [ 3.486729] Block layer SCSI generic (bsg) driver version 0.4 loaded
>(major 253)
>> + [ 3.486788] io scheduler mq-deadline registered
>> + [ 3.486822] io scheduler kyber registered
>> + [ 3.528973] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
>> + [ 3.530114] 10010000.serial: ttySIF0 at MMIO 0x10010000 (irq = 1,
>base_baud = 0) is a SiFive UART v0
>> + [ 4.061558] printk: console [ttySIF0] enabled
>> + [ 4.066211] 10011000.serial: ttySIF1 at MMIO 0x10011000 (irq = 10,
>base_baud = 0) is a SiFive UART v0
>> + [ 4.075620] [drm] radeon kernel modesetting enabled.
>> + [ 4.092998] loop: module loaded
>> + [ 4.096007] sifive_spi 10040000.spi: mapped; irq=12, cs=1
>> + [ 4.101380] sifive_spi 10050000.spi: mapped; irq=13, cs=1
>> + [ 4.107129] libphy: Fixed MDIO Bus: probed
>> + [ 4.111232] macb 10090000.ethernet: Registered clk switch 'sifive-
>gemgxl-mgmt'
>> + [ 4.117841] macb 10090000.ethernet: GEM doesn't support hardware
>ptp.
>> + [ 4.124654] libphy: MACB_mii_bus: probed
>> + [ 4.133149] macb 10090000.ethernet eth0: Cadence GEM rev
>0x10070109 at 0x10090000 irq 14 (86:5d:6f:58:d6:3d)
>> + [ 4.142400] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
>> + [ 4.148053] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
>> + [ 4.154051] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI)
>Driver
>> + [ 4.160470] ehci-pci: EHCI PCI platform driver
>> + [ 4.164930] ehci-platform: EHCI generic platform driver
>> + [ 4.170185] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
>> + [ 4.176284] ohci-pci: OHCI PCI platform driver
>> + [ 4.180736] ohci-platform: OHCI generic platform driver
>> + [ 4.186226] usbcore: registered new interface driver uas
>> + [ 4.191257] usbcore: registered new interface driver usb-storage
>> + [ 4.197392] mousedev: PS/2 mouse device common for all mice
>> + [ 4.228311] mmc_spi spi1.0: SD/MMC host mmc0, no DMA, no WP,
>no poweroff, cd polling
>> + [ 4.235528] usbcore: registered new interface driver usbhid
>> + [ 4.240870] usbhid: USB HID core driver
>> + [ 4.245515] NET: Registered protocol family 10
>> + [ 4.250603] Segment Routing with IPv6
>> + [ 4.253602] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
>> + [ 4.259978] NET: Registered protocol family 17
>> + [ 4.264098] 9pnet: Installing 9P2000 support
>> + [ 4.268159] Key type dns_resolver registered
>> + [ 4.279265] Freeing unused kernel memory: 236K
>> + [ 4.282989] This architecture does not have kernel memory
>protection.
>> + [ 4.289390] Run /init as init process
>> + Starting syslogd: OK
>> + Starting klogd: OK
>> + Starting mdev...
>> + /etc/init.d/S10mdev: line 9: can't create /proc/sys/kernel/hotplug:
>nonexistent directory
>> + [ 4.354461] mmc0: host does not support reading read-only switch,
>assuming write-enable
>> + [ 4.361778] mmc0: new SDHC card on SPI
>> + [ 4.381184] mmcblk0: mmc0:0000 SC16G 14.8 GiB
>> + [ 4.424975] mmcblk0: p1 p2 p3
>> + modprobe: can't change directory to '/lib/modules': No such file or
>directory
>> + Initializing random number generator... [ 5.041362] random: dd:
>uninitialized urandom read (512 bytes read)
>> + done.
>> + Starting network: [ 5.240580] macb 10090000.ethernet eth0: PHY
>[10090000.ethernet-ffffffff:00] driver [Microsemi VSC8541 SyncE] (irq=POLL)
>> + [ 5.250752] macb 10090000.ethernet eth0: configuring for phy/gmii
>link mode
>> + udhcpc: started, v1.29.3
>> + udhcpc: sending discover
>> + [ 7.301682] macb 10090000.ethernet eth0: Link is Up - 100Mbps/Full -
>flow control tx
>> + [ 7.308726] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes
>ready
>> + udhcpc: sending discover
>> + udhcpc: sending discover
>> + udhcpc: no lease, failing
>> + FAIL
>> + Starting dropbear sshd: [ 14.309152] random: dropbear: uninitialized
>urandom read (32 bytes read)
>> + OK
>> +
>> + Welcome to Buildroot
>> + buildroot login: root
>> + Password:
>> + #
>> --
>> 2.17.1
>>
>
>Otherwise looks good to me.
>
>Reviewed-by: Anup Patel <anup@brainfault.org>
>
>Regards,
>Anup
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 16/22] riscv: Enable cpu clock if it is present
2020-05-02 18:15 ` Sean Anderson
@ 2020-05-03 7:12 ` Pragnesh Patel
2020-05-03 17:17 ` Sean Anderson
0 siblings, 1 reply; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-03 7:12 UTC (permalink / raw)
To: u-boot
Hi Sean,
>-----Original Message-----
>From: Sean Anderson <seanga2@gmail.com>
>Sent: 02 May 2020 23:46
>To: Pragnesh Patel <pragnesh.patel@sifive.com>; u-boot at lists.denx.de
>Cc: atish.patra at wdc.com; palmerdabbelt at google.com;
>bmeng.cn at gmail.com; Paul Walmsley <paul.walmsley@sifive.com>;
>jagan at amarulasolutions.com; Troy Benjegerdes
><troy.benjegerdes@sifive.com>; anup.patel at wdc.com; Sagar Kadam
><sagar.kadam@sifive.com>; rick at andestech.com; Lukas Auer
><lukas.auer@aisec.fraunhofer.de>
>Subject: Re: [PATCH v7 16/22] riscv: Enable cpu clock if it is present
>
>[External Email] Do not click links or attachments unless you recognize the
>sender and know the content is safe
>
>On 5/2/20 6:06 AM, Pragnesh Patel wrote:
>> The cpu clock is probably already enabled if we are executing code
>> (though we could be executing from a different core). This patch
>> prevents the cpu clock or its parents from being disabled.
>>
>> Signed-off-by: Sean Anderson <seanga2@gmail.com>
>
>If you make substantial changes can you please make a note of it in the
>commit? I did not sign off on *this* code.
This patch is copied from your v9 series [1] and I made some changes, so the idea is to
give credit to everyone who contributed.
[1]
https://patchwork.ozlabs.org/project/uboot/patch/20200503023550.326791-19-seanga2 at gmail.com/
>
>> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
>> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
>> ---
>> drivers/cpu/riscv_cpu.c | 33 +++++++++++++++++++++++++++++++++
>> 1 file changed, 33 insertions(+)
>>
>> diff --git a/drivers/cpu/riscv_cpu.c b/drivers/cpu/riscv_cpu.c index
>> 28ad0aa30f..8ebe0341fd 100644
>> --- a/drivers/cpu/riscv_cpu.c
>> +++ b/drivers/cpu/riscv_cpu.c
>> @@ -9,6 +9,7 @@
>> #include <errno.h>
>> #include <dm/device-internal.h>
>> #include <dm/lists.h>
>> +#include <clk.h>
>>
>> DECLARE_GLOBAL_DATA_PTR;
>>
>> @@ -100,6 +101,37 @@ static int riscv_cpu_bind(struct udevice *dev)
>> return 0;
>> }
>>
>> +static int riscv_cpu_probe(struct udevice *dev) {
>> + int ret = 0;
>> + u32 clock = 0;
>> + struct clk clk;
>> +
>> + /* Get a clock if it exists */
>> + ret = clk_get_by_index(dev, 0, &clk);
>> + if (ret)
>> + return 0;
>> +
>> + ret = dev_read_u32(dev, "clock-frequency", &clock);
>
>Ok, so as I understand it, your goal for your changes this patch is to have a
>way to set the cpu frequency on startup. However, I think the cpu-frequency
>property is not the correct way to go about this when we have a clock from
>the device tree. In this case, one should use the
>assigned-clock* properties to have the frequency set automatically when
>clk_get_by_index is called. There is no need to add this functionality here.
>
>With the previous patch in the series you pulled this from [1], one could easily
>do something like
>
>cpus {
> assigned-clocks = <&foo FOO_CPU>;
> assigned-clock-frequency = <100000000>;
> cpu at 0 {
> /* ... */
> clocks = <&foo FOO_CPU>;
> /* ... */
> };
>};
>
>which would use existing code to assign the frequency.
>
>[1]
>https://patchwork.ozlabs.org/project/uboot/patch/20200423023320.1380090
>-18-seanga2 at gmail.com/
Thanks for pointing this out to me, I will give it a try with your patch [1] and drop this patch if not
necessary.
[1]
https://patchwork.ozlabs.org/project/uboot/patch/20200503023550.326791-19-seanga2 at gmail.com/
>
>> + if (ret) {
>> + debug("clock-frequency not found in dt %d\n", ret);
>
>This should not be an error. You also need to check for ENOSYS and
>ENOTSUPP like below.
Thanks for the review, will take care in future.
>
>> + return ret;
>> + } else {
>> + ret = clk_set_rate(&clk, clock);
>> + if (ret < 0) {
>> + debug("Could not set CPU clock\n");
>
>Neither should this be.
will take care in future.
>
>> + return ret;
>> + }
>> + }
>> +
>> + ret = clk_enable(&clk);
>> + clk_free(&clk);
>> + if (ret == -ENOSYS || ret == -ENOTSUPP)
>
>All clk_ calls can return ENOSYS and ENOTSUPP. These are returned when the
>underlying clock does not support the operation. However, they are not
>appropriate errors to return from this function.
Thanks for the explanation, will take care in future.
>
>> + return 0;
>> + else
>> + return ret;
>> +}
>> +
>> static const struct cpu_ops riscv_cpu_ops = {
>> .get_desc = riscv_cpu_get_desc,
>> .get_info = riscv_cpu_get_info,
>> @@ -116,6 +148,7 @@ U_BOOT_DRIVER(riscv_cpu) = {
>> .id = UCLASS_CPU,
>> .of_match = riscv_cpu_ids,
>> .bind = riscv_cpu_bind,
>> + .probe = riscv_cpu_probe,
>> .ops = &riscv_cpu_ops,
>> .flags = DM_FLAG_PRE_RELOC,
>> };
>>
>
>--Sean
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 00/22] RISC-V SiFive FU540 support SPL
2020-05-02 17:18 ` [PATCH v7 00/22] RISC-V SiFive FU540 support SPL Jagan Teki
@ 2020-05-03 7:19 ` Pragnesh Patel
0 siblings, 0 replies; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-03 7:19 UTC (permalink / raw)
To: u-boot
Hi Jagan,
>-----Original Message-----
>From: Jagan Teki <jagan@amarulasolutions.com>
>Sent: 02 May 2020 22:49
>To: Pragnesh Patel <pragnesh.patel@sifive.com>
>Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Bin
>Meng <bmeng.cn@gmail.com>; Paul Walmsley <paul.walmsley@sifive.com>;
>Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
><rick@andestech.com>
>Subject: Re: [PATCH v7 00/22] RISC-V SiFive FU540 support SPL
>
>[External Email] Do not click links or attachments unless you recognize the
>sender and know the content is safe
>
>On Sat, May 2, 2020 at 3:37 PM Pragnesh Patel <pragnesh.patel@sifive.com>
>wrote:
>>
>> This series add support for SPL to FU540.U-Boot SPL can boot from
>> L2 LIM (0x0800_0000) and jump to OpenSBI(FW_DYNAMIC firmware) and
>> U-Boot proper from MMC devices.
>>
>> How to test this patch:
>> 1) Go to OpenSBI-dir : make PLATFORM=generic FW_DYNAMIC=y
>> 2) export
>> OPENSBI=<path/to/opensbi/install_dir/platform/generic/firmware/fw_dyna
>> mic.bin>
>> 3) Change to u-boot-dir
>> 4) make sifive_fu540_defconfig
>> 5) make all
>> 6) Format the SD card (make sure the disk has GPT, otherwise use gdisk
>> to switch)
>>
>> # sudo sgdisk --clear \
>> > --set-alignment=2 \
>> > --new=1:34:2081 --change-name=1:loader1 --typecode=1:5B193300-
>FC78-40CD-8002-E86C45580B47 \
>> > --new=2:2082:10273 --change-name=2:loader2 --
>typecode=2:2E54B353-1271-4842-806F-E436D6AF6985 \
>> > --new=3:10274: --change-name=3:rootfs --typecode=3:0FC63DAF-
>8483-4772-8E79-3D69D8477DE4 \
>> > /dev/sda
>>
>> 7) sudo dd if=spl/u-boot-spl.bin of=/dev/sda seek=34
>> 8) sudo dd if=u-boot.itb of=/dev/sda seek=2082
>
>Most patches improved from v6, but still few issues like
>- patches which are unrelated to MMC SPL support, please bypass and send
>them separately.
Will update in v8.
>- order of patches need to improve, take my suggestions and order them.
Sure.
>- incorporate partition layout patches before SPL enablement patch.
Will do, I thought you will send v3 of [1] that's why I did not incorporate that changes.
I will incorporate in v8.
[1]
https://patchwork.amarulasolutions.com/patch/1092/
>
>Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 18/22] configs: fu540: Add config options for U-Boot SPL
2020-05-02 17:15 ` Jagan Teki
@ 2020-05-03 7:20 ` Pragnesh Patel
0 siblings, 0 replies; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-03 7:20 UTC (permalink / raw)
To: u-boot
Hi jagan,
>-----Original Message-----
>From: Jagan Teki <jagan@amarulasolutions.com>
>Sent: 02 May 2020 22:45
>To: Pragnesh Patel <pragnesh.patel@sifive.com>
>Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Bin
>Meng <bmeng.cn@gmail.com>; Paul Walmsley <paul.walmsley@sifive.com>;
>Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
><rick@andestech.com>; Palmer Dabbelt <palmer@dabbelt.com>
>Subject: Re: [PATCH v7 18/22] configs: fu540: Add config options for U-Boot
>SPL
>
>[External Email] Do not click links or attachments unless you recognize the
>sender and know the content is safe
>
>On Sat, May 2, 2020 at 3:38 PM Pragnesh Patel <pragnesh.patel@sifive.com>
>wrote:
>>
>> With sifive_fu540_defconfig:
>>
>> User can use FSBL or u-boot-spl.bin anyone at a time.
>>
>> For FSBL,
>> fsbl->fw_payload.bin (opensbi + U-Boot)
>>
>> For u-boot-spl.bin,
>> u-boot-spl.bin->FIT image (opensbi + U-Boot + dtb)
>>
>> U-Boot SPL will be loaded by ZSBL from SD card (replace fsbl.bin with
>> u-boot-spl.bin) and runs in L2 LIM in machine mode and then load FIT
>> image u-boot.itb from SD card into RAM.
>>
>> U-Boot SPL expects u-boot.itb FIT image at the starting of SD card
>> sector number (0x822) of GUID type "2E54B353-1271-4842-806F-
>E436D6AF6985"
>>
>
>Prior to this patch you have
>https://patchwork.ozlabs.org/project/uboot/patch/20200420133735.23599-1-
>jagan at amarulasolutions.com/
>https://patchwork.ozlabs.org/project/uboot/patch/20200420133735.23599-2-
>jagan at amarulasolutions.com/
>
>in the series, otherwise it will not boot from MMC with this series.
Will incorporate in v8.
>
>Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
2020-05-02 17:13 ` Jagan Teki
@ 2020-05-03 7:27 ` Pragnesh Patel
2020-05-10 9:31 ` Jagan Teki
0 siblings, 1 reply; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-03 7:27 UTC (permalink / raw)
To: u-boot
Hi jagan,
>-----Original Message-----
>From: Jagan Teki <jagan@amarulasolutions.com>
>Sent: 02 May 2020 22:43
>To: Pragnesh Patel <pragnesh.patel@sifive.com>
>Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Bin
>Meng <bmeng.cn@gmail.com>; Paul Walmsley <paul.walmsley@sifive.com>;
>Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
><rick@andestech.com>
>Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
>
>[External Email] Do not click links or attachments unless you recognize the
>sender and know the content is safe
>
>On Sat, May 2, 2020 at 10:12 PM Pragnesh Patel <pragnesh.patel@sifive.com>
>wrote:
>>
>> Hi Jagan,
>>
>> >-----Original Message-----
>> >From: Jagan Teki <jagan@amarulasolutions.com>
>> >Sent: 02 May 2020 21:49
>> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
>> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
>> ><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>;
>Bin
>> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
><paul.walmsley@sifive.com>;
>> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
>> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick
>Chen
>> ><rick@andestech.com>
>> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in
>> >U-Boot
>> >
>> >[External Email] Do not click links or attachments unless you
>> >recognize the sender and know the content is safe
>> >
>> >On Sat, May 2, 2020 at 3:39 PM Pragnesh Patel
>> ><pragnesh.patel@sifive.com>
>> >wrote:
>> >>
>> >> Add L2 cache node to enable cache ways from U-Boot
>> >
>> >This and 20/22 doesn't relate to SPL MMC boot?, if yes please send
>> >them separately.
>>
>> This series is for replacing FSBL and all the patches are related to that.
>> IMHO it's better to add all FSBL functionality in one series.
>
>You mean does it break existing FSBL flow? if yes add proper commit message,
>but I am able to boot SPL MMC w/o this?
Cache ways are enabled by FSBL also and if I will send cache ways patches separately then it will a duplicate
way of enabling cache ways if someone using FSBL.
Let me know if you still want me to send cache ways patches separately ?
>
>Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 15/22] riscv: sifive: dts: fu540: Add clock for cpus node
2020-05-02 16:50 ` Jagan Teki
@ 2020-05-03 8:55 ` Pragnesh Patel
0 siblings, 0 replies; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-03 8:55 UTC (permalink / raw)
To: u-boot
Hi Jagan,
>-----Original Message-----
>From: Jagan Teki <jagan@amarulasolutions.com>
>Sent: 02 May 2020 22:20
>To: Pragnesh Patel <pragnesh.patel@sifive.com>
>Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Bin
>Meng <bmeng.cn@gmail.com>; Paul Walmsley <paul.walmsley@sifive.com>;
>Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
><rick@andestech.com>
>Subject: Re: [PATCH v7 15/22] riscv: sifive: dts: fu540: Add clock for cpus node
>
>[External Email] Do not click links or attachments unless you recognize the
>sender and know the content is safe
>
>On Sat, May 2, 2020 at 3:38 PM Pragnesh Patel <pragnesh.patel@sifive.com>
>wrote:
>>
>> Add clock-frequency and clocks in cpus node, so that clock will be
>> enabled by cpu driver.
>>
>> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
>> ---
>
>Squash this with 05/22
Will update in v8.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 10/22] clk: sifive: fu540-prci: ddr and ethernet clock initialization in SPL
2020-05-02 16:44 ` Jagan Teki
@ 2020-05-03 8:57 ` Pragnesh Patel
0 siblings, 0 replies; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-03 8:57 UTC (permalink / raw)
To: u-boot
Hi Jagan,
>-----Original Message-----
>From: Jagan Teki <jagan@amarulasolutions.com>
>Sent: 02 May 2020 22:15
>To: Pragnesh Patel <pragnesh.patel@sifive.com>
>Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Bin
>Meng <bmeng.cn@gmail.com>; Paul Walmsley <paul.walmsley@sifive.com>;
>Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
><rick@andestech.com>; Lukasz Majewski <lukma@denx.de>; Anatolij
>Gustschin <agust@denx.de>; Simon Glass <sjg@chromium.org>
>Subject: Re: [PATCH v7 10/22] clk: sifive: fu540-prci: ddr and ethernet clock
>initialization in SPL
>
>[External Email] Do not click links or attachments unless you recognize the
>sender and know the content is safe
>
>On Sat, May 2, 2020 at 10:05 PM Pragnesh Patel <pragnesh.patel@sifive.com>
>wrote:
>>
>> Hi Jagan,
>>
>> >-----Original Message-----
>> >From: Jagan Teki <jagan@amarulasolutions.com>
>> >Sent: 02 May 2020 21:44
>> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
>> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
>> ><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>;
>Bin
>> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
><paul.walmsley@sifive.com>;
>> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
>> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick
>Chen
>> ><rick@andestech.com>; Lukasz Majewski <lukma@denx.de>; Anatolij
>> >Gustschin <agust@denx.de>; Simon Glass <sjg@chromium.org>
>> >Subject: Re: [PATCH v7 10/22] clk: sifive: fu540-prci: ddr and
>> >ethernet clock initialization in SPL
>> >
>> >[External Email] Do not click links or attachments unless you
>> >recognize the sender and know the content is safe
>> >
>> >On Sat, May 2, 2020 at 3:38 PM Pragnesh Patel
>> ><pragnesh.patel@sifive.com>
>> >wrote:
>> >>
>> >> Add ddr clock release reset and ehternet clock initialization for
>> >> SPL
>> >
>> >Why ethernet still require for SPL?
>>
>> I think we have already discussed this in v6.
>> https://patchwork.ozlabs.org/project/uboot/patch/20200329170538.25449-
>> 10-pragnesh.patel at sifive.com/
>
>Understand, then make a separate patch for "Ethernet SPL" but not in this
>series.
I will make a separate patch in this series.
This series is not just for SPL MMC boot but the real intention is to replace FSBL with U-Boot SPL so
all FSBL functionality should be in one series.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 13/22] riscv: cpu: fu540: Add support for cpu fu540
2020-05-02 16:34 ` Jagan Teki
@ 2020-05-03 9:16 ` Pragnesh Patel
0 siblings, 0 replies; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-03 9:16 UTC (permalink / raw)
To: u-boot
Hi Jagan,
>-----Original Message-----
>From: Jagan Teki <jagan@amarulasolutions.com>
>Sent: 02 May 2020 22:05
>To: Pragnesh Patel <pragnesh.patel@sifive.com>
>Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Bin
>Meng <bmeng.cn@gmail.com>; Paul Walmsley <paul.walmsley@sifive.com>;
>Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
><rick@andestech.com>; Lukas Auer <lukas.auer@aisec.fraunhofer.de>; Simon
>Glass <sjg@chromium.org>
>Subject: Re: [PATCH v7 13/22] riscv: cpu: fu540: Add support for cpu fu540
>
>[External Email] Do not click links or attachments unless you recognize the
>sender and know the content is safe
>
>On Sat, May 2, 2020 at 3:38 PM Pragnesh Patel <pragnesh.patel@sifive.com>
>wrote:
>>
>> Add SiFive fu540 cpu to support RISC-V arch
>
>This looks like a new patch in this series, isn't it?
Yes.
>
>>
>> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
>> ---
>
>Good practice is to add "changes for 7" so-that it is easy for reviews to find
>what is new in this series.
Will take care in future. For this series, I am just updating cover letter.
>
>> arch/riscv/Kconfig | 1 +
>> arch/riscv/cpu/fu540/Kconfig | 15 ++++++++++++++
>> arch/riscv/cpu/fu540/Makefile | 7 +++++++
>> arch/riscv/cpu/fu540/cpu.c | 22 ++++++++++++++++++++
>> arch/riscv/cpu/fu540/dram.c | 38
>+++++++++++++++++++++++++++++++++++
>> 5 files changed, 83 insertions(+)
>> create mode 100644 arch/riscv/cpu/fu540/Kconfig create mode 100644
>> arch/riscv/cpu/fu540/Makefile create mode 100644
>> arch/riscv/cpu/fu540/cpu.c create mode 100644
>> arch/riscv/cpu/fu540/dram.c
>>
>> diff --git a/arch/riscv/Kconfig b/arch/riscv/Kconfig index
>> fb5fe5afff..3044609971 100644
>> --- a/arch/riscv/Kconfig
>> +++ b/arch/riscv/Kconfig
>> @@ -57,6 +57,7 @@ source "board/sifive/fu540/Kconfig"
>> # platform-specific options below
>> source "arch/riscv/cpu/ax25/Kconfig"
>> source "arch/riscv/cpu/generic/Kconfig"
>> +source "arch/riscv/cpu/fu540/Kconfig"
>>
>> # architecture-specific options below
>>
>> diff --git a/arch/riscv/cpu/fu540/Kconfig
>> b/arch/riscv/cpu/fu540/Kconfig new file mode 100644 index
>> 0000000000..b2cb155d6d
>> --- /dev/null
>> +++ b/arch/riscv/cpu/fu540/Kconfig
>> @@ -0,0 +1,15 @@
>> +# SPDX-License-Identifier: GPL-2.0+
>> +#
>> +# Copyright (C) 2018, Bin Meng <bmeng.cn@gmail.com>
>> +
>> +config GENERIC_RISCV
>> + bool
>> + select ARCH_EARLY_INIT_R
>> + imply CPU
>> + imply CPU_RISCV
>> + imply RISCV_TIMER
>> + imply SIFIVE_CLINT if (RISCV_MMODE || SPL_RISCV_MMODE)
>> + imply CMD_CPU
>> + imply SPL_CPU_SUPPORT
>> + imply SPL_OPENSBI
>> + imply SPL_LOAD_FIT
>> diff --git a/arch/riscv/cpu/fu540/Makefile
>> b/arch/riscv/cpu/fu540/Makefile new file mode 100644 index
>> 0000000000..44700d998c
>> --- /dev/null
>> +++ b/arch/riscv/cpu/fu540/Makefile
>> @@ -0,0 +1,7 @@
>> +# SPDX-License-Identifier: GPL-2.0+
>> +#
>> +# Copyright (C) 2020 SiFive, Inc
>> +# Pragnesh Patel <pragnesh.patel@sifive.com>
>> +
>> +obj-y += dram.o
>> +obj-y += cpu.o
>> diff --git a/arch/riscv/cpu/fu540/cpu.c b/arch/riscv/cpu/fu540/cpu.c
>> new file mode 100644 index 0000000000..13a69ef0cc
>> --- /dev/null
>> +++ b/arch/riscv/cpu/fu540/cpu.c
>> @@ -0,0 +1,22 @@
>> +// SPDX-License-Identifier: GPL-2.0+
>> +/*
>> + * Copyright (C) 2018, Bin Meng <bmeng.cn@gmail.com> */
>> +
>> +#include <common.h>
>> +#include <irq_func.h>
>> +
>> +/*
>> + * cleanup_before_linux() is called just before we call linux
>> + * it prepares the processor for linux
>> + *
>> + * we disable interrupt and caches.
>> + */
>> +int cleanup_before_linux(void)
>> +{
>> + disable_interrupts();
>> +
>> + cache_flush();
>> +
>> + return 0;
>> +}
>> diff --git a/arch/riscv/cpu/fu540/dram.c b/arch/riscv/cpu/fu540/dram.c
>> new file mode 100644 index 0000000000..1dc77efeca
>> --- /dev/null
>> +++ b/arch/riscv/cpu/fu540/dram.c
>> @@ -0,0 +1,38 @@
>> +// SPDX-License-Identifier: GPL-2.0+
>> +/*
>> + * Copyright (C) 2018, Bin Meng <bmeng.cn@gmail.com> */
>> +
>> +#include <common.h>
>> +#include <fdtdec.h>
>> +#include <init.h>
>> +#include <linux/sizes.h>
>> +
>> +DECLARE_GLOBAL_DATA_PTR;
>> +
>> +int dram_init(void)
>> +{
>> + return fdtdec_setup_mem_size_base(); }
>> +
>> +int dram_init_banksize(void)
>> +{
>> + return fdtdec_setup_memory_banksize(); }
>> +
>> +ulong board_get_usable_ram_top(ulong total_size) { #ifdef
>> +CONFIG_64BIT
>> + /*
>> + * Ensure that we run from first 4GB so that all
>> + * addresses used by U-Boot are 32bit addresses.
>> + *
>> + * This in-turn ensures that 32bit DMA capable
>> + * devices work fine because DMA mapping APIs will
>> + * provide 32bit DMA addresses only.
>> + */
>> + if (gd->ram_top > SZ_4G)
>> + return SZ_4G;
>> +#endif
>> + return gd->ram_top;
>
>Is all this code common across SPL and U-Boot proper? except that SPL config
>imply.
For SPL, only spl.c file is necessary. All other files are compiled only for U-Boot proper.
You can check this in "arch/riscv/cpu/fu540/Makefile".
>
>Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 14/22] riscv: Add place-holder for driver compilation
2020-05-02 16:27 ` Jagan Teki
@ 2020-05-03 9:17 ` Pragnesh Patel
2020-05-10 9:12 ` Jagan Teki
0 siblings, 1 reply; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-03 9:17 UTC (permalink / raw)
To: u-boot
Hi Jagan,
>-----Original Message-----
>From: Jagan Teki <jagan@amarulasolutions.com>
>Sent: 02 May 2020 21:58
>To: Pragnesh Patel <pragnesh.patel@sifive.com>
>Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Bin
>Meng <bmeng.cn@gmail.com>; Paul Walmsley <paul.walmsley@sifive.com>;
>Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
><rick@andestech.com>
>Subject: Re: [PATCH v7 14/22] riscv: Add place-holder for driver compilation
>
>[External Email] Do not click links or attachments unless you recognize the
>sender and know the content is safe
>
>On Sat, May 2, 2020 at 3:38 PM Pragnesh Patel <pragnesh.patel@sifive.com>
>wrote:
>>
>> Add place-holder for RISC-V fu540 CPU
>>
>> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
>> ---
>> arch/riscv/include/asm/arch-fu540/clk.h | 14 +++++++++
>> arch/riscv/include/asm/arch-fu540/gpio.h | 38 ++++++++++++++++++++++++
>
>Where is it using exactly?
"drivers/gpio/sifive-gpio.c"
>
>Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 04/22] lib: Makefile: build crc7.c when CONFIG_MMC_SPI
2020-05-02 12:58 ` Heinrich Schuchardt
2020-05-02 15:33 ` Jagan Teki
@ 2020-05-03 9:54 ` Pragnesh Patel
1 sibling, 0 replies; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-03 9:54 UTC (permalink / raw)
To: u-boot
Hi Heinrich,
>-----Original Message-----
>From: Heinrich Schuchardt <xypron.glpk@gmx.de>
>Sent: 02 May 2020 18:29
>To: Bin Meng <bmeng.cn@gmail.com>
>Cc: Pragnesh Patel <pragnesh.patel@sifive.com>; U-Boot Mailing List <u-
>boot at lists.denx.de>; Jagan Teki <jagan@amarulasolutions.com>; Atish Patra
><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Paul
>Walmsley <paul.walmsley@sifive.com>; Troy Benjegerdes
><troy.benjegerdes@sifive.com>; Anup Patel <anup.patel@wdc.com>; Sagar
>Kadam <sagar.kadam@sifive.com>; Rick Chen <rick@andestech.com>; Peng
>Fan <peng.fan@nxp.com>; Lukasz Majewski <lukma@denx.de>; Simon
>Goldschmidt <simon.k.r.goldschmidt@gmail.com>; Simon Glass
><sjg@chromium.org>; Markus Klotzbuecher
><markus.klotzbuecher@kistler.com>; Baruch Siach <baruch@tkos.co.il>; Joel
>Johnson <mrjoel@lixil.net>; Anatolij Gustschin <agust@denx.de>; AKASHI
>Takahiro <takahiro.akashi@linaro.org>; Marek Beh?n <marek.behun@nic.cz>
>Subject: Re: [PATCH v7 04/22] lib: Makefile: build crc7.c when
>CONFIG_MMC_SPI
>
>[External Email] Do not click links or attachments unless you recognize the
>sender and know the content is safe
>
>Am May 2, 2020 11:47:10 AM UTC schrieb Bin Meng <bmeng.cn@gmail.com>:
>>Hi Heinrich,
>>
>>On Sat, May 2, 2020 at 6:30 PM Heinrich Schuchardt <xypron.glpk@gmx.de>
>>wrote:
>>>
>>> On 5/2/20 12:06 PM, Pragnesh Patel wrote:
>>> > When build U-Boot SPL, meet an issue of undefined reference to
>>> > 'crc7' for drivers/mmc/mmc_spi.c, so let's compile crc7.c when
>>> > CONFIG_MMC_SPI selected.
>>> >
>>> > Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
>>> > Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
>>> > Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
>>> > ---
>>> > common/spl/Kconfig | 6 ++++++
>>> > drivers/mmc/Kconfig | 1 +
>>> > lib/Makefile | 1 +
>>> > 3 files changed, 8 insertions(+)
>>> >
>>> > diff --git a/common/spl/Kconfig b/common/spl/Kconfig index
>>> > ef5bf66696..d1f0e6bc4c 100644
>>> > --- a/common/spl/Kconfig
>>> > +++ b/common/spl/Kconfig
>>> > @@ -401,6 +401,12 @@ config SPL_CRC32_SUPPORT
>>> > for detected accidental image corruption. For secure
>>applications you
>>> > should consider SHA1 or SHA256.
>>> >
>>> > +config SPL_CRC7_SUPPORT
>>> > + bool "Support CRC7"
>>> > + help
>>> > + Enable CRC7 hashing for drivers which are using in SPL.
>>> > + This is a 32-bit checksum value that can be used to verify
>>images.
>>> > +
>>> > config SPL_MD5_SUPPORT
>>> > bool "Support MD5"
>>> > depends on SPL_FIT
>>> > diff --git a/drivers/mmc/Kconfig b/drivers/mmc/Kconfig index
>>> > 8f0df568b9..139599072a 100644
>>> > --- a/drivers/mmc/Kconfig
>>> > +++ b/drivers/mmc/Kconfig
>>> > @@ -49,6 +49,7 @@ if MMC
>>> > config MMC_SPI
>>> > bool "Support for SPI-based MMC controller"
>>> > depends on DM_MMC && DM_SPI
>>> > + select SPL_CRC7_SUPPORT if SPL
>>> > help
>>> > This selects SPI-based MMC controllers.
>>> > If you have an MMC controller on a SPI bus, say Y here.
>>> > diff --git a/lib/Makefile b/lib/Makefile index
>>> > c6f862b0c2..fcd934857f 100644
>>> > --- a/lib/Makefile
>>> > +++ b/lib/Makefile
>>> > @@ -80,6 +80,7 @@ endif
>>> >
>>> > ifdef CONFIG_SPL_BUILD
>>> > obj-$(CONFIG_SPL_YMODEM_SUPPORT) += crc16.o
>>> > +obj-$(CONFIG_SPL_CRC7_SUPPORT) += crc7.o
>>>
>>> crc7.o is not needed in main U-Boot if MMC_SPI is not selected.
>>>
>>> So instead of adding a new configuration variable simply correct the
>>> existing line in lib/Makefile
>>>
>>> -obj-y += crc7.o
>>> +obj-$(CONFIG_MMC_SPI) += crc7.o
>>
>>This looks incorrect to me. CRC7 can be useful for other drivers too.
>>It should not depend on CONFIG_MMC_SPI.
>
>Using this argument you would always compile everything. Compiling files that
>are not used is simply a waste of CPU time.
>
>Following your argument. you could also always compile crc7.c for SPL and
>hope the compiler will eliminate it.
>
>Either way we do not need a new config symbol.
I think this is already discussed in v3.
https://patchwork.ozlabs.org/project/uboot/patch/20200124055026.30787-4-pragnesh.patel at sifive.com/
>
>Best regards
>
>Heinrich
>
>>
>>>
>>> and move that line inside lib/Makefile so that is does not depend on
>>> CONFIG_SPL_BUILD.
>>>
>>
>>Regards,
>>Bin
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 16/22] riscv: Enable cpu clock if it is present
2020-05-03 7:12 ` Pragnesh Patel
@ 2020-05-03 17:17 ` Sean Anderson
2020-05-04 5:20 ` Pragnesh Patel
0 siblings, 1 reply; 118+ messages in thread
From: Sean Anderson @ 2020-05-03 17:17 UTC (permalink / raw)
To: u-boot
On 5/3/20 3:12 AM, Pragnesh Patel wrote:
> Hi Sean,
>
>> -----Original Message-----
>> From: Sean Anderson <seanga2@gmail.com>
>> Sent: 02 May 2020 23:46
>> To: Pragnesh Patel <pragnesh.patel@sifive.com>; u-boot at lists.denx.de
>> Cc: atish.patra at wdc.com; palmerdabbelt at google.com;
>> bmeng.cn at gmail.com; Paul Walmsley <paul.walmsley@sifive.com>;
>> jagan at amarulasolutions.com; Troy Benjegerdes
>> <troy.benjegerdes@sifive.com>; anup.patel at wdc.com; Sagar Kadam
>> <sagar.kadam@sifive.com>; rick at andestech.com; Lukas Auer
>> <lukas.auer@aisec.fraunhofer.de>
>> Subject: Re: [PATCH v7 16/22] riscv: Enable cpu clock if it is present
>>
>> [External Email] Do not click links or attachments unless you recognize the
>> sender and know the content is safe
>>
>> On 5/2/20 6:06 AM, Pragnesh Patel wrote:
>>> The cpu clock is probably already enabled if we are executing code
>>> (though we could be executing from a different core). This patch
>>> prevents the cpu clock or its parents from being disabled.
>>>
>>> Signed-off-by: Sean Anderson <seanga2@gmail.com>
>>
>> If you make substantial changes can you please make a note of it in the
>> commit? I did not sign off on *this* code.
>
> This patch is copied from your v9 series [1] and I made some changes, so the idea is to
> give credit to everyone who contributed.
That's fine, just please make a note when you make substantial changes.
For example, you could write
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[set clock frequency from clock-frequency property]
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
so it's more clear what changes have been made since this patch was
posted last.
--Sean
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 16/22] riscv: Enable cpu clock if it is present
2020-05-03 17:17 ` Sean Anderson
@ 2020-05-04 5:20 ` Pragnesh Patel
0 siblings, 0 replies; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-04 5:20 UTC (permalink / raw)
To: u-boot
Hi Sean,
>-----Original Message-----
>From: Sean Anderson <seanga2@gmail.com>
>Sent: 03 May 2020 22:47
>To: Pragnesh Patel <pragnesh.patel@sifive.com>; u-boot at lists.denx.de
>Cc: atish.patra at wdc.com; palmerdabbelt at google.com;
>bmeng.cn at gmail.com; Paul Walmsley <paul.walmsley@sifive.com>;
>jagan at amarulasolutions.com; Troy Benjegerdes
><troy.benjegerdes@sifive.com>; anup.patel at wdc.com; Sagar Kadam
><sagar.kadam@sifive.com>; rick at andestech.com; Lukas Auer
><lukas.auer@aisec.fraunhofer.de>
>Subject: Re: [PATCH v7 16/22] riscv: Enable cpu clock if it is present
>
>[External Email] Do not click links or attachments unless you recognize the
>sender and know the content is safe
>
>On 5/3/20 3:12 AM, Pragnesh Patel wrote:
>> Hi Sean,
>>
>>> -----Original Message-----
>>> From: Sean Anderson <seanga2@gmail.com>
>>> Sent: 02 May 2020 23:46
>>> To: Pragnesh Patel <pragnesh.patel@sifive.com>; u-boot at lists.denx.de
>>> Cc: atish.patra at wdc.com; palmerdabbelt at google.com;
>>> bmeng.cn at gmail.com; Paul Walmsley <paul.walmsley@sifive.com>;
>>> jagan at amarulasolutions.com; Troy Benjegerdes
>>> <troy.benjegerdes@sifive.com>; anup.patel at wdc.com; Sagar Kadam
>>> <sagar.kadam@sifive.com>; rick at andestech.com; Lukas Auer
>>> <lukas.auer@aisec.fraunhofer.de>
>>> Subject: Re: [PATCH v7 16/22] riscv: Enable cpu clock if it is
>>> present
>>>
>>> [External Email] Do not click links or attachments unless you
>>> recognize the sender and know the content is safe
>>>
>>> On 5/2/20 6:06 AM, Pragnesh Patel wrote:
>>>> The cpu clock is probably already enabled if we are executing code
>>>> (though we could be executing from a different core). This patch
>>>> prevents the cpu clock or its parents from being disabled.
>>>>
>>>> Signed-off-by: Sean Anderson <seanga2@gmail.com>
>>>
>>> If you make substantial changes can you please make a note of it in
>>> the commit? I did not sign off on *this* code.
>>
>> This patch is copied from your v9 series [1] and I made some changes,
>> so the idea is to give credit to everyone who contributed.
>
>That's fine, just please make a note when you make substantial changes.
>For example, you could write
>
>Signed-off-by: Sean Anderson <seanga2@gmail.com>
>Reviewed-by: Bin Meng <bmeng.cn@gmail.com> [set clock frequency from
>clock-frequency property]
>Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
>
>so it's more clear what changes have been made since this patch was posted
>last.
Will take care in future.
>
>--Sean
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 04/22] lib: Makefile: build crc7.c when CONFIG_MMC_SPI
2020-05-02 15:33 ` Jagan Teki
@ 2020-05-04 5:45 ` Pragnesh Patel
2020-05-05 15:55 ` Pragnesh Patel
0 siblings, 1 reply; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-04 5:45 UTC (permalink / raw)
To: u-boot
>-----Original Message-----
>From: Jagan Teki <jagan@amarulasolutions.com>
>Sent: 02 May 2020 21:04
>To: Heinrich Schuchardt <xypron.glpk@gmx.de>; Pragnesh Patel
><pragnesh.patel@sifive.com>; Bin Meng <bmeng.cn@gmail.com>
>Cc: U-Boot Mailing List <u-boot@lists.denx.de>; Atish Patra
><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Paul
>Walmsley <paul.walmsley@sifive.com>; Troy Benjegerdes
><troy.benjegerdes@sifive.com>; Anup Patel <anup.patel@wdc.com>; Sagar
>Kadam <sagar.kadam@sifive.com>; Rick Chen <rick@andestech.com>; Peng
>Fan <peng.fan@nxp.com>; Lukasz Majewski <lukma@denx.de>; Simon
>Goldschmidt <simon.k.r.goldschmidt@gmail.com>; Simon Glass
><sjg@chromium.org>; Markus Klotzbuecher
><markus.klotzbuecher@kistler.com>; Baruch Siach <baruch@tkos.co.il>; Joel
>Johnson <mrjoel@lixil.net>; Anatolij Gustschin <agust@denx.de>; AKASHI
>Takahiro <takahiro.akashi@linaro.org>; Marek Beh?n <marek.behun@nic.cz>
>Subject: Re: [PATCH v7 04/22] lib: Makefile: build crc7.c when
>CONFIG_MMC_SPI
>
>[External Email] Do not click links or attachments unless you recognize the
>sender and know the content is safe
>
>On Sat, May 2, 2020 at 6:45 PM Heinrich Schuchardt <xypron.glpk@gmx.de>
>wrote:
>>
>> Am May 2, 2020 11:47:10 AM UTC schrieb Bin Meng
><bmeng.cn@gmail.com>:
>> >Hi Heinrich,
>> >
>> >On Sat, May 2, 2020 at 6:30 PM Heinrich Schuchardt
>> ><xypron.glpk@gmx.de>
>> >wrote:
>> >>
>> >> On 5/2/20 12:06 PM, Pragnesh Patel wrote:
>> >> > When build U-Boot SPL, meet an issue of undefined reference to
>> >> > 'crc7' for drivers/mmc/mmc_spi.c, so let's compile crc7.c when
>> >> > CONFIG_MMC_SPI selected.
>> >> >
>> >> > Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
>> >> > Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
>> >> > Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
>> >> > ---
>> >> > common/spl/Kconfig | 6 ++++++
>> >> > drivers/mmc/Kconfig | 1 +
>> >> > lib/Makefile | 1 +
>> >> > 3 files changed, 8 insertions(+)
>> >> >
>> >> > diff --git a/common/spl/Kconfig b/common/spl/Kconfig index
>> >> > ef5bf66696..d1f0e6bc4c 100644
>> >> > --- a/common/spl/Kconfig
>> >> > +++ b/common/spl/Kconfig
>> >> > @@ -401,6 +401,12 @@ config SPL_CRC32_SUPPORT
>> >> > for detected accidental image corruption. For secure
>> >applications you
>> >> > should consider SHA1 or SHA256.
>> >> >
>> >> > +config SPL_CRC7_SUPPORT
>> >> > + bool "Support CRC7"
>> >> > + help
>> >> > + Enable CRC7 hashing for drivers which are using in SPL.
>> >> > + This is a 32-bit checksum value that can be used to
>> >> > +verify
>> >images.
>> >> > +
>> >> > config SPL_MD5_SUPPORT
>> >> > bool "Support MD5"
>> >> > depends on SPL_FIT
>> >> > diff --git a/drivers/mmc/Kconfig b/drivers/mmc/Kconfig index
>> >> > 8f0df568b9..139599072a 100644
>> >> > --- a/drivers/mmc/Kconfig
>> >> > +++ b/drivers/mmc/Kconfig
>> >> > @@ -49,6 +49,7 @@ if MMC
>> >> > config MMC_SPI
>> >> > bool "Support for SPI-based MMC controller"
>> >> > depends on DM_MMC && DM_SPI
>> >> > + select SPL_CRC7_SUPPORT if SPL
>> >> > help
>> >> > This selects SPI-based MMC controllers.
>> >> > If you have an MMC controller on a SPI bus, say Y here.
>> >> > diff --git a/lib/Makefile b/lib/Makefile index
>> >> > c6f862b0c2..fcd934857f 100644
>> >> > --- a/lib/Makefile
>> >> > +++ b/lib/Makefile
>> >> > @@ -80,6 +80,7 @@ endif
>> >> >
>> >> > ifdef CONFIG_SPL_BUILD
>> >> > obj-$(CONFIG_SPL_YMODEM_SUPPORT) += crc16.o
>> >> > +obj-$(CONFIG_SPL_CRC7_SUPPORT) += crc7.o
>> >>
>> >> crc7.o is not needed in main U-Boot if MMC_SPI is not selected.
>> >>
>> >> So instead of adding a new configuration variable simply correct
>> >> the existing line in lib/Makefile
>> >>
>> >> -obj-y += crc7.o
>> >> +obj-$(CONFIG_MMC_SPI) += crc7.o
>> >
>> >This looks incorrect to me. CRC7 can be useful for other drivers too.
>> >It should not depend on CONFIG_MMC_SPI.
>>
>> Using this argument you would always compile everything. Compiling files
>that are not used is simply a waste of CPU time.
>>
>> Following your argument. you could also always compile crc7.c for SPL and
>hope the compiler will eliminate it.
>>
>> Either way we do not need a new config symbol.
>
>This is one of the reasons I just suggested that the mark 'depends on
>MMC_SPI' at the very initial patch.
>
>Marking config SPL_CRC7_SUPPORT which depends on MMC_SPI would work
>for me.
@Jagan Teki I think MMC_SPI should be depend on or select SPL_CRC7_SUPPORT.
SPL_CRC7_SUPPORT is not depend on MMC_SPI.
@Heinrich Schuchardt Compiling crc7.o every time is not a good idea. I have 1 suggestion,
Can we make 1 Kconfig like
+config CRC7_SUPPORT
+ bool "Support CRC7"
+ help
+ Enable CRC7 hashing for drivers.
+ This is a 32-bit checksum value that can be used to verify images.
Which is common for U-Boot proper and U-Boot SPL and compile crc7
+ obj-$(CONFIG_CRC7_SUPPORT) += crc7.o
Any suggestions are welcome ?
>
>Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 18/22] configs: fu540: Add config options for U-Boot SPL
2020-05-02 16:51 ` Jagan Teki
@ 2020-05-04 15:48 ` Pragnesh Patel
0 siblings, 0 replies; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-04 15:48 UTC (permalink / raw)
To: u-boot
Hi Jagan,
>-----Original Message-----
>From: Jagan Teki <jagan@amarulasolutions.com>
>Sent: 02 May 2020 22:22
>To: Pragnesh Patel <pragnesh.patel@sifive.com>
>Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Bin
>Meng <bmeng.cn@gmail.com>; Paul Walmsley <paul.walmsley@sifive.com>;
>Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
><rick@andestech.com>; Palmer Dabbelt <palmer@dabbelt.com>
>Subject: Re: [PATCH v7 18/22] configs: fu540: Add config options for U-Boot
>SPL
>
>[External Email] Do not click links or attachments unless you recognize the
>sender and know the content is safe
>
>On Sat, May 2, 2020 at 3:38 PM Pragnesh Patel <pragnesh.patel@sifive.com>
>wrote:
>>
>> With sifive_fu540_defconfig:
>>
>> User can use FSBL or u-boot-spl.bin anyone at a time.
>>
>> For FSBL,
>> fsbl->fw_payload.bin (opensbi + U-Boot)
>>
>> For u-boot-spl.bin,
>> u-boot-spl.bin->FIT image (opensbi + U-Boot + dtb)
>>
>> U-Boot SPL will be loaded by ZSBL from SD card (replace fsbl.bin with
>> u-boot-spl.bin) and runs in L2 LIM in machine mode and then load FIT
>> image u-boot.itb from SD card into RAM.
>>
>> U-Boot SPL expects u-boot.itb FIT image at the starting of SD card
>> sector number (0x822) of GUID type "2E54B353-1271-4842-806F-
>E436D6AF6985"
>>
>> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
>> ---
>
>squash with 12/22 and 22/22.
IMHO, it's better to squash this patch with 22/22 and squash 12/22 with 17/22.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 04/22] lib: Makefile: build crc7.c when CONFIG_MMC_SPI
2020-05-04 5:45 ` Pragnesh Patel
@ 2020-05-05 15:55 ` Pragnesh Patel
2020-05-08 5:59 ` Pragnesh Patel
0 siblings, 1 reply; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-05 15:55 UTC (permalink / raw)
To: u-boot
>-----Original Message-----
>From: U-Boot <u-boot-bounces@lists.denx.de> On Behalf Of Pragnesh Patel
>Sent: 04 May 2020 11:15
>To: Jagan Teki <jagan@amarulasolutions.com>; Heinrich Schuchardt
><xypron.glpk@gmx.de>; Bin Meng <bmeng.cn@gmail.com>
>Cc: U-Boot Mailing List <u-boot@lists.denx.de>; Atish Patra
><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Paul
>Walmsley <paul.walmsley@sifive.com>; Troy Benjegerdes
><troy.benjegerdes@sifive.com>; Anup Patel <anup.patel@wdc.com>; Sagar
>Kadam <sagar.kadam@sifive.com>; Rick Chen <rick@andestech.com>; Peng
>Fan <peng.fan@nxp.com>; Lukasz Majewski <lukma@denx.de>; Simon
>Goldschmidt <simon.k.r.goldschmidt@gmail.com>; Simon Glass
><sjg@chromium.org>; Markus Klotzbuecher
><markus.klotzbuecher@kistler.com>; Baruch Siach <baruch@tkos.co.il>; Joel
>Johnson <mrjoel@lixil.net>; Anatolij Gustschin <agust@denx.de>; AKASHI
>Takahiro <takahiro.akashi@linaro.org>; Marek Beh?n <marek.behun@nic.cz>
>Subject: RE: [PATCH v7 04/22] lib: Makefile: build crc7.c when
>CONFIG_MMC_SPI
>
>>-----Original Message-----
>>From: Jagan Teki <jagan@amarulasolutions.com>
>>Sent: 02 May 2020 21:04
>>To: Heinrich Schuchardt <xypron.glpk@gmx.de>; Pragnesh Patel
>><pragnesh.patel@sifive.com>; Bin Meng <bmeng.cn@gmail.com>
>>Cc: U-Boot Mailing List <u-boot@lists.denx.de>; Atish Patra
>><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>;
>Paul
>>Walmsley <paul.walmsley@sifive.com>; Troy Benjegerdes
>><troy.benjegerdes@sifive.com>; Anup Patel <anup.patel@wdc.com>; Sagar
>>Kadam <sagar.kadam@sifive.com>; Rick Chen <rick@andestech.com>; Peng
>>Fan <peng.fan@nxp.com>; Lukasz Majewski <lukma@denx.de>; Simon
>>Goldschmidt <simon.k.r.goldschmidt@gmail.com>; Simon Glass
>><sjg@chromium.org>; Markus Klotzbuecher
>><markus.klotzbuecher@kistler.com>; Baruch Siach <baruch@tkos.co.il>;
>>Joel Johnson <mrjoel@lixil.net>; Anatolij Gustschin <agust@denx.de>;
>>AKASHI Takahiro <takahiro.akashi@linaro.org>; Marek Beh?n
>><marek.behun@nic.cz>
>>Subject: Re: [PATCH v7 04/22] lib: Makefile: build crc7.c when
>>CONFIG_MMC_SPI
>>
>>[External Email] Do not click links or attachments unless you recognize
>>the sender and know the content is safe
>>
>>On Sat, May 2, 2020 at 6:45 PM Heinrich Schuchardt <xypron.glpk@gmx.de>
>>wrote:
>>>
>>> Am May 2, 2020 11:47:10 AM UTC schrieb Bin Meng
>><bmeng.cn@gmail.com>:
>>> >Hi Heinrich,
>>> >
>>> >On Sat, May 2, 2020 at 6:30 PM Heinrich Schuchardt
>>> ><xypron.glpk@gmx.de>
>>> >wrote:
>>> >>
>>> >> On 5/2/20 12:06 PM, Pragnesh Patel wrote:
>>> >> > When build U-Boot SPL, meet an issue of undefined reference to
>>> >> > 'crc7' for drivers/mmc/mmc_spi.c, so let's compile crc7.c when
>>> >> > CONFIG_MMC_SPI selected.
>>> >> >
>>> >> > Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
>>> >> > Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
>>> >> > Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
>>> >> > ---
>>> >> > common/spl/Kconfig | 6 ++++++
>>> >> > drivers/mmc/Kconfig | 1 +
>>> >> > lib/Makefile | 1 +
>>> >> > 3 files changed, 8 insertions(+)
>>> >> >
>>> >> > diff --git a/common/spl/Kconfig b/common/spl/Kconfig index
>>> >> > ef5bf66696..d1f0e6bc4c 100644
>>> >> > --- a/common/spl/Kconfig
>>> >> > +++ b/common/spl/Kconfig
>>> >> > @@ -401,6 +401,12 @@ config SPL_CRC32_SUPPORT
>>> >> > for detected accidental image corruption. For secure
>>> >applications you
>>> >> > should consider SHA1 or SHA256.
>>> >> >
>>> >> > +config SPL_CRC7_SUPPORT
>>> >> > + bool "Support CRC7"
>>> >> > + help
>>> >> > + Enable CRC7 hashing for drivers which are using in SPL.
>>> >> > + This is a 32-bit checksum value that can be used to
>>> >> > +verify
>>> >images.
>>> >> > +
>>> >> > config SPL_MD5_SUPPORT
>>> >> > bool "Support MD5"
>>> >> > depends on SPL_FIT
>>> >> > diff --git a/drivers/mmc/Kconfig b/drivers/mmc/Kconfig index
>>> >> > 8f0df568b9..139599072a 100644
>>> >> > --- a/drivers/mmc/Kconfig
>>> >> > +++ b/drivers/mmc/Kconfig
>>> >> > @@ -49,6 +49,7 @@ if MMC
>>> >> > config MMC_SPI
>>> >> > bool "Support for SPI-based MMC controller"
>>> >> > depends on DM_MMC && DM_SPI
>>> >> > + select SPL_CRC7_SUPPORT if SPL
>>> >> > help
>>> >> > This selects SPI-based MMC controllers.
>>> >> > If you have an MMC controller on a SPI bus, say Y here.
>>> >> > diff --git a/lib/Makefile b/lib/Makefile index
>>> >> > c6f862b0c2..fcd934857f 100644
>>> >> > --- a/lib/Makefile
>>> >> > +++ b/lib/Makefile
>>> >> > @@ -80,6 +80,7 @@ endif
>>> >> >
>>> >> > ifdef CONFIG_SPL_BUILD
>>> >> > obj-$(CONFIG_SPL_YMODEM_SUPPORT) += crc16.o
>>> >> > +obj-$(CONFIG_SPL_CRC7_SUPPORT) += crc7.o
>>> >>
>>> >> crc7.o is not needed in main U-Boot if MMC_SPI is not selected.
>>> >>
>>> >> So instead of adding a new configuration variable simply correct
>>> >> the existing line in lib/Makefile
>>> >>
>>> >> -obj-y += crc7.o
>>> >> +obj-$(CONFIG_MMC_SPI) += crc7.o
>>> >
>>> >This looks incorrect to me. CRC7 can be useful for other drivers too.
>>> >It should not depend on CONFIG_MMC_SPI.
>>>
>>> Using this argument you would always compile everything. Compiling
>>> files
>>that are not used is simply a waste of CPU time.
>>>
>>> Following your argument. you could also always compile crc7.c for SPL
>>> and
>>hope the compiler will eliminate it.
>>>
>>> Either way we do not need a new config symbol.
>>
>>This is one of the reasons I just suggested that the mark 'depends on
>>MMC_SPI' at the very initial patch.
>>
>>Marking config SPL_CRC7_SUPPORT which depends on MMC_SPI would work
>for
>>me.
>
>@Jagan Teki I think MMC_SPI should be depend on or select
>SPL_CRC7_SUPPORT.
>SPL_CRC7_SUPPORT is not depend on MMC_SPI.
>
>@Heinrich Schuchardt Compiling crc7.o every time is not a good idea. I have 1
>suggestion, Can we make 1 Kconfig like
>
>+config CRC7_SUPPORT
>+ bool "Support CRC7"
>+ help
>+ Enable CRC7 hashing for drivers.
>+ This is a 32-bit checksum value that can be used to verify images.
>
>Which is common for U-Boot proper and U-Boot SPL and compile crc7
>
>+ obj-$(CONFIG_CRC7_SUPPORT) += crc7.o
>
>Any suggestions are welcome ?
Any comment, I am planning to send v8.
>
>>
>>Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 04/22] lib: Makefile: build crc7.c when CONFIG_MMC_SPI
2020-05-05 15:55 ` Pragnesh Patel
@ 2020-05-08 5:59 ` Pragnesh Patel
0 siblings, 0 replies; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-08 5:59 UTC (permalink / raw)
To: u-boot
>-----Original Message-----
>From: U-Boot <u-boot-bounces@lists.denx.de> On Behalf Of Pragnesh Patel
>Sent: 05 May 2020 21:25
>To: Jagan Teki <jagan@amarulasolutions.com>; Heinrich Schuchardt
><xypron.glpk@gmx.de>; Bin Meng <bmeng.cn@gmail.com>
>Cc: U-Boot Mailing List <u-boot@lists.denx.de>; Atish Patra
><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Paul
>Walmsley <paul.walmsley@sifive.com>; Troy Benjegerdes
><troy.benjegerdes@sifive.com>; Anup Patel <anup.patel@wdc.com>; Sagar
>Kadam <sagar.kadam@sifive.com>; Rick Chen <rick@andestech.com>; Peng
>Fan <peng.fan@nxp.com>; Lukasz Majewski <lukma@denx.de>; Simon
>Goldschmidt <simon.k.r.goldschmidt@gmail.com>; Simon Glass
><sjg@chromium.org>; Markus Klotzbuecher
><markus.klotzbuecher@kistler.com>; Baruch Siach <baruch@tkos.co.il>; Joel
>Johnson <mrjoel@lixil.net>; Anatolij Gustschin <agust@denx.de>; AKASHI
>Takahiro <takahiro.akashi@linaro.org>; Marek Beh?n <marek.behun@nic.cz>
>Subject: RE: [PATCH v7 04/22] lib: Makefile: build crc7.c when
>CONFIG_MMC_SPI
>
>
>
>>-----Original Message-----
>>From: U-Boot <u-boot-bounces@lists.denx.de> On Behalf Of Pragnesh Patel
>>Sent: 04 May 2020 11:15
>>To: Jagan Teki <jagan@amarulasolutions.com>; Heinrich Schuchardt
>><xypron.glpk@gmx.de>; Bin Meng <bmeng.cn@gmail.com>
>>Cc: U-Boot Mailing List <u-boot@lists.denx.de>; Atish Patra
>><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>;
>Paul
>>Walmsley <paul.walmsley@sifive.com>; Troy Benjegerdes
>><troy.benjegerdes@sifive.com>; Anup Patel <anup.patel@wdc.com>; Sagar
>>Kadam <sagar.kadam@sifive.com>; Rick Chen <rick@andestech.com>; Peng
>>Fan <peng.fan@nxp.com>; Lukasz Majewski <lukma@denx.de>; Simon
>>Goldschmidt <simon.k.r.goldschmidt@gmail.com>; Simon Glass
>><sjg@chromium.org>; Markus Klotzbuecher
>><markus.klotzbuecher@kistler.com>; Baruch Siach <baruch@tkos.co.il>;
>>Joel Johnson <mrjoel@lixil.net>; Anatolij Gustschin <agust@denx.de>;
>>AKASHI Takahiro <takahiro.akashi@linaro.org>; Marek Beh?n
>><marek.behun@nic.cz>
>>Subject: RE: [PATCH v7 04/22] lib: Makefile: build crc7.c when
>>CONFIG_MMC_SPI
>>
>>>-----Original Message-----
>>>From: Jagan Teki <jagan@amarulasolutions.com>
>>>Sent: 02 May 2020 21:04
>>>To: Heinrich Schuchardt <xypron.glpk@gmx.de>; Pragnesh Patel
>>><pragnesh.patel@sifive.com>; Bin Meng <bmeng.cn@gmail.com>
>>>Cc: U-Boot Mailing List <u-boot@lists.denx.de>; Atish Patra
>>><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>;
>>Paul
>>>Walmsley <paul.walmsley@sifive.com>; Troy Benjegerdes
>>><troy.benjegerdes@sifive.com>; Anup Patel <anup.patel@wdc.com>; Sagar
>>>Kadam <sagar.kadam@sifive.com>; Rick Chen <rick@andestech.com>; Peng
>>>Fan <peng.fan@nxp.com>; Lukasz Majewski <lukma@denx.de>; Simon
>>>Goldschmidt <simon.k.r.goldschmidt@gmail.com>; Simon Glass
>>><sjg@chromium.org>; Markus Klotzbuecher
>>><markus.klotzbuecher@kistler.com>; Baruch Siach <baruch@tkos.co.il>;
>>>Joel Johnson <mrjoel@lixil.net>; Anatolij Gustschin <agust@denx.de>;
>>>AKASHI Takahiro <takahiro.akashi@linaro.org>; Marek Beh?n
>>><marek.behun@nic.cz>
>>>Subject: Re: [PATCH v7 04/22] lib: Makefile: build crc7.c when
>>>CONFIG_MMC_SPI
>>>
>>>[External Email] Do not click links or attachments unless you
>>>recognize the sender and know the content is safe
>>>
>>>On Sat, May 2, 2020 at 6:45 PM Heinrich Schuchardt
>>><xypron.glpk@gmx.de>
>>>wrote:
>>>>
>>>> Am May 2, 2020 11:47:10 AM UTC schrieb Bin Meng
>>><bmeng.cn@gmail.com>:
>>>> >Hi Heinrich,
>>>> >
>>>> >On Sat, May 2, 2020 at 6:30 PM Heinrich Schuchardt
>>>> ><xypron.glpk@gmx.de>
>>>> >wrote:
>>>> >>
>>>> >> On 5/2/20 12:06 PM, Pragnesh Patel wrote:
>>>> >> > When build U-Boot SPL, meet an issue of undefined reference to
>>>> >> > 'crc7' for drivers/mmc/mmc_spi.c, so let's compile crc7.c when
>>>> >> > CONFIG_MMC_SPI selected.
>>>> >> >
>>>> >> > Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
>>>> >> > Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
>>>> >> > Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
>>>> >> > ---
>>>> >> > common/spl/Kconfig | 6 ++++++ drivers/mmc/Kconfig | 1 +
>>>> >> > lib/Makefile | 1 +
>>>> >> > 3 files changed, 8 insertions(+)
>>>> >> >
>>>> >> > diff --git a/common/spl/Kconfig b/common/spl/Kconfig index
>>>> >> > ef5bf66696..d1f0e6bc4c 100644
>>>> >> > --- a/common/spl/Kconfig
>>>> >> > +++ b/common/spl/Kconfig
>>>> >> > @@ -401,6 +401,12 @@ config SPL_CRC32_SUPPORT
>>>> >> > for detected accidental image corruption. For secure
>>>> >applications you
>>>> >> > should consider SHA1 or SHA256.
>>>> >> >
>>>> >> > +config SPL_CRC7_SUPPORT
>>>> >> > + bool "Support CRC7"
>>>> >> > + help
>>>> >> > + Enable CRC7 hashing for drivers which are using in SPL.
>>>> >> > + This is a 32-bit checksum value that can be used to
>>>> >> > +verify
>>>> >images.
>>>> >> > +
>>>> >> > config SPL_MD5_SUPPORT
>>>> >> > bool "Support MD5"
>>>> >> > depends on SPL_FIT
>>>> >> > diff --git a/drivers/mmc/Kconfig b/drivers/mmc/Kconfig index
>>>> >> > 8f0df568b9..139599072a 100644
>>>> >> > --- a/drivers/mmc/Kconfig
>>>> >> > +++ b/drivers/mmc/Kconfig
>>>> >> > @@ -49,6 +49,7 @@ if MMC
>>>> >> > config MMC_SPI
>>>> >> > bool "Support for SPI-based MMC controller"
>>>> >> > depends on DM_MMC && DM_SPI
>>>> >> > + select SPL_CRC7_SUPPORT if SPL
>>>> >> > help
>>>> >> > This selects SPI-based MMC controllers.
>>>> >> > If you have an MMC controller on a SPI bus, say Y here.
>>>> >> > diff --git a/lib/Makefile b/lib/Makefile index
>>>> >> > c6f862b0c2..fcd934857f 100644
>>>> >> > --- a/lib/Makefile
>>>> >> > +++ b/lib/Makefile
>>>> >> > @@ -80,6 +80,7 @@ endif
>>>> >> >
>>>> >> > ifdef CONFIG_SPL_BUILD
>>>> >> > obj-$(CONFIG_SPL_YMODEM_SUPPORT) += crc16.o
>>>> >> > +obj-$(CONFIG_SPL_CRC7_SUPPORT) += crc7.o
>>>> >>
>>>> >> crc7.o is not needed in main U-Boot if MMC_SPI is not selected.
>>>> >>
>>>> >> So instead of adding a new configuration variable simply correct
>>>> >> the existing line in lib/Makefile
>>>> >>
>>>> >> -obj-y += crc7.o
>>>> >> +obj-$(CONFIG_MMC_SPI) += crc7.o
>>>> >
>>>> >This looks incorrect to me. CRC7 can be useful for other drivers too.
>>>> >It should not depend on CONFIG_MMC_SPI.
>>>>
>>>> Using this argument you would always compile everything. Compiling
>>>> files
>>>that are not used is simply a waste of CPU time.
>>>>
>>>> Following your argument. you could also always compile crc7.c for
>>>> SPL and
>>>hope the compiler will eliminate it.
>>>>
>>>> Either way we do not need a new config symbol.
>>>
>>>This is one of the reasons I just suggested that the mark 'depends on
>>>MMC_SPI' at the very initial patch.
>>>
>>>Marking config SPL_CRC7_SUPPORT which depends on MMC_SPI would
>work
>>for
>>>me.
>>
>>@Jagan Teki I think MMC_SPI should be depend on or select
>>SPL_CRC7_SUPPORT.
>>SPL_CRC7_SUPPORT is not depend on MMC_SPI.
>>
>>@Heinrich Schuchardt Compiling crc7.o every time is not a good idea. I
>>have 1 suggestion, Can we make 1 Kconfig like
>>
>>+config CRC7_SUPPORT
>>+ bool "Support CRC7"
>>+ help
>>+ Enable CRC7 hashing for drivers.
>>+ This is a 32-bit checksum value that can be used to verify images.
>>
>>Which is common for U-Boot proper and U-Boot SPL and compile crc7
>>
>>+ obj-$(CONFIG_CRC7_SUPPORT) += crc7.o
>>
>>Any suggestions are welcome ?
>
>Any comment, I am planning to send v8.
I am going with Heinrich's suggestion and remove SPL Kconfig in v8.
>
>>
>>>
>>>Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 10/22] clk: sifive: fu540-prci: ddr and ethernet clock initialization in SPL
2020-05-02 14:49 ` Pragnesh Patel
@ 2020-05-09 11:29 ` Pragnesh Patel
0 siblings, 0 replies; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-09 11:29 UTC (permalink / raw)
To: u-boot
Hi Bin,
>-----Original Message-----
>From: U-Boot <u-boot-bounces@lists.denx.de> On Behalf Of Pragnesh Patel
>Sent: 02 May 2020 20:20
>To: Bin Meng <bmeng.cn@gmail.com>; Troy Benjegerdes
><troy.benjegerdes@sifive.com>
>Cc: U-Boot Mailing List <u-boot@lists.denx.de>; Atish Patra
><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Paul
>Walmsley <paul.walmsley@sifive.com>; Jagan Teki
><jagan@amarulasolutions.com>; Anup Patel <anup.patel@wdc.com>; Sagar
>Kadam <sagar.kadam@sifive.com>; Rick Chen <rick@andestech.com>; Lukasz
>Majewski <lukma@denx.de>; Anatolij Gustschin <agust@denx.de>; Simon
>Glass <sjg@chromium.org>
>Subject: RE: [PATCH v7 10/22] clk: sifive: fu540-prci: ddr and ethernet clock
>initialization in SPL
>
>Hi Bin,
>
>>-----Original Message-----
>>From: Bin Meng <bmeng.cn@gmail.com>
>>Sent: 02 May 2020 17:58
>>To: Pragnesh Patel <pragnesh.patel@sifive.com>
>>Cc: U-Boot Mailing List <u-boot@lists.denx.de>; Atish Patra
>><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>;
>Paul
>>Walmsley <paul.walmsley@sifive.com>; Jagan Teki
>><jagan@amarulasolutions.com>; Troy Benjegerdes
>><troy.benjegerdes@sifive.com>; Anup Patel <anup.patel@wdc.com>; Sagar
>>Kadam <sagar.kadam@sifive.com>; Rick Chen <rick@andestech.com>;
>Lukasz
>>Majewski <lukma@denx.de>; Anatolij Gustschin <agust@denx.de>; Simon
>>Glass <sjg@chromium.org>
>>Subject: Re: [PATCH v7 10/22] clk: sifive: fu540-prci: ddr and ethernet
>>clock initialization in SPL
>>
>>[External Email] Do not click links or attachments unless you recognize
>>the sender and know the content is safe
>>
>>Hi Pragnesh,
>>
>>On Sat, May 2, 2020 at 6:08 PM Pragnesh Patel
>><pragnesh.patel@sifive.com>
>>wrote:
>>>
>>> Add ddr clock release reset and ehternet clock initialization for SPL
>>>
>>> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
>>> ---
>>> drivers/clk/sifive/fu540-prci.c | 87
>>> ++++++++++++++++++++++++++++++---
>>> 1 file changed, 81 insertions(+), 6 deletions(-)
>>>
>>> diff --git a/drivers/clk/sifive/fu540-prci.c
>>> b/drivers/clk/sifive/fu540-prci.c index bf06c3a3bb..1c89bdf242 100644
>>> --- a/drivers/clk/sifive/fu540-prci.c
>>> +++ b/drivers/clk/sifive/fu540-prci.c
>>> @@ -41,6 +41,8 @@
>>> #include <linux/clk/analogbits-wrpll-cln28hpc.h>
>>> #include <dt-bindings/clock/sifive-fu540-prci.h>
>>>
>>> +#define MHz 1000000
>>> +
>>> /*
>>> * EXPECTED_CLK_PARENT_COUNT: how many parent clocks this driver
>>expects:
>>> * hfclk and rtcclk
>>> @@ -152,6 +154,12 @@
>>> #define PRCI_CLKMUXSTATUSREG_TLCLKSEL_STATUS_MASK \
>>> (0x1 <<
>>> PRCI_CLKMUXSTATUSREG_TLCLKSEL_STATUS_SHIFT)
>>>
>>> +/* PROCMONCFG */
>>> +#define PRCI_PROCMONCFG_OFFSET 0xF0
>>> +#define PRCI_PROCMONCFG_CORE_CLOCK_SHIFT 24
>>> +#define PRCI_PROCMONCFG_CORE_CLOCK_MASK \
>>> + (0x1 << PRCI_PROCMONCFG_CORE_CLOCK_SHIFT)
>>> +
>>> /*
>>> * Private structures
>>> */
>>> @@ -176,6 +184,7 @@ struct __prci_data {
>>> * @disable_bypass: fn ptr to code to not bypass the WRPLL (or NULL)
>>> * @cfg0_offs: WRPLL CFG0 register offset (in bytes) from the PRCI
>>> base
>>address
>>> * @cfg1_offs: WRPLL CFG1 register offset (in bytes) from the PRCI
>>> base address
>>> + * @release_reset: fn ptr to code to release clock reset
>>> *
>>> * @enable_bypass and @disable_bypass are used for WRPLL instances
>>> * that contain a separate external glitchless clock mux downstream
>>> @@ -187,6 +196,9 @@ struct __prci_wrpll_data {
>>> void (*disable_bypass)(struct __prci_data *pd);
>>> u8 cfg0_offs;
>>> u8 cfg1_offs;
>>> +#ifdef CONFIG_SPL_BUILD
>>> + void (*release_reset)(struct __prci_data *pd); #endif
>>> };
>>>
>>> struct __prci_clock;
>>> @@ -476,6 +488,11 @@ static int sifive_fu540_prci_clock_enable(struct
>>> __prci_clock *pc, bool enable)
>>>
>>> if (enable) {
>>> __prci_wrpll_write_cfg1(pd, pwd,
>>> PRCI_COREPLLCFG1_CKE_MASK);
>>> +
>>> +#ifdef CONFIG_SPL_BUILD
>>> + if (pwd->release_reset)
>>> + pwd->release_reset(pd); #endif
>>> } else {
>>> u32 r;
>>>
>>> @@ -495,11 +512,6 @@ static const struct __prci_clock_ops
>>sifive_fu540_prci_wrpll_clk_ops = {
>>> .enable_clk = sifive_fu540_prci_clock_enable, };
>>>
>>> -static const struct __prci_clock_ops sifive_fu540_prci_wrpll_ro_clk_ops =
>{
>>> - .recalc_rate = sifive_fu540_prci_wrpll_recalc_rate,
>>> - .enable_clk = sifive_fu540_prci_clock_enable,
>>> -};
>>> -
>>> /* TLCLKSEL clock integration */
>>>
>>> static unsigned long sifive_fu540_prci_tlclksel_recalc_rate(
>>> @@ -521,6 +533,39 @@ static const struct __prci_clock_ops
>>sifive_fu540_prci_tlclksel_clk_ops = {
>>> .recalc_rate = sifive_fu540_prci_tlclksel_recalc_rate,
>>> };
>>>
>>> +#ifdef CONFIG_SPL_BUILD
>>> +/**
>>> + * __prci_ddr_release_reset() - Release DDR reset
>>> + * @pd: struct __prci_data * for the PRCI containing the DDRCLK mux
>>> +reg
>>> + *
>>> + */
>>> +static void __prci_ddr_release_reset(struct __prci_data *pd) {
>>> + u32 v;
>>> +
>>> + v = __prci_readl(pd, PRCI_DEVICESRESETREG_OFFSET);
>>> + v |= PRCI_DEVICESRESETREG_DDR_CTRL_RST_N_MASK;
>>> + __prci_writel(v, PRCI_DEVICESRESETREG_OFFSET, pd);
>>> +
>>> + // HACK to get the '1 full controller clock cycle'.
>>
>>nits: should use /* */
>
>Will update in v8.
>
>>
>>> + asm volatile ("fence");
>>> + v = __prci_readl(pd, PRCI_DEVICESRESETREG_OFFSET);
>>> + v |= (PRCI_DEVICESRESETREG_DDR_AXI_RST_N_MASK |
>>> + PRCI_DEVICESRESETREG_DDR_AHB_RST_N_MASK |
>>> + PRCI_DEVICESRESETREG_DDR_PHY_RST_N_MASK);
>>> + __prci_writel(v, PRCI_DEVICESRESETREG_OFFSET, pd);
>>> + // HACK to get the '1 full controller clock cycle'.
>>
>>the same here
>
>Will update in v8.
>
>>
>>> + asm volatile ("fence");
>>> +
>>> + /* These take like 16 cycles to actually propagate. We can't
>>> + go sending
>>
>>nits: wrong multi-line comment format
>
>Will update in v8.
>
>>
>>> + * stuff before they come out of reset. So wait. (TODO: Add a register
>>> + * to read the current reset states, or DDR Control device?)
>>
>>Is there no register to reflect the reset states?
>
>As of now, I don't know about this. This is something copied from FSBL.
>Right now, we need to go with TODO.
>
>@Troy Benjegerdes Do you have any idea on this ?
I discussed this "TODO" with my colleagues and I got below :
This "TODO" refers to the hardware side -- we should add some registers to monitor stuff.
So as far as the software is concerned, we can just remove the TODO.
Will remove this TODO in v8.
>
>>
>>> + */
>>> + for (int i = 0; i < 256; i++)
>>> + asm volatile ("nop"); } #endif
>>> +
>>> /*
>>> * PRCI integration data for each WRPLL instance
>>> */
>>> @@ -535,6 +580,9 @@ static struct __prci_wrpll_data
>>> __prci_corepll_data = { static struct __prci_wrpll_data
>>> __prci_ddrpll_data =
>>{
>>> .cfg0_offs = PRCI_DDRPLLCFG0_OFFSET,
>>> .cfg1_offs = PRCI_DDRPLLCFG1_OFFSET,
>>> +#ifdef CONFIG_SPL_BUILD
>>> + .release_reset = __prci_ddr_release_reset, #endif
>>> };
>>>
>>> static struct __prci_wrpll_data __prci_gemgxlpll_data = { @@ -556,7
>>> +604,7 @@ static struct __prci_clock __prci_init_clocks[] = {
>>> [PRCI_CLK_DDRPLL] = {
>>> .name = "ddrpll",
>>> .parent_name = "hfclk",
>>> - .ops = &sifive_fu540_prci_wrpll_ro_clk_ops,
>>> + .ops = &sifive_fu540_prci_wrpll_clk_ops,
>>> .pwd = &__prci_ddrpll_data,
>>> },
>>> [PRCI_CLK_GEMGXLPLL] = {
>>> @@ -662,6 +710,29 @@ static int sifive_fu540_prci_disable(struct clk *clk)
>>> return ret;
>>> }
>>>
>>> +#ifdef CONFIG_SPL_BUILD
>>> +static void ethernet_init(struct udevice *dev) {
>>> + u32 v;
>>> + struct clk clock;
>>> + struct __prci_data *pd = dev_get_priv(dev);
>>> +
>>> + /* GEMGXL init */
>>> + clock.id = PRCI_CLK_GEMGXLPLL;
>>> + sifive_fu540_prci_set_rate(&clock, 125UL * MHz);
>>> + sifive_fu540_prci_clock_enable(&__prci_init_clocks[clock.id],
>>> + 1);
>>> +
>>> + /* Release GEMGXL reset */
>>> + v = __prci_readl(pd, PRCI_DEVICESRESETREG_OFFSET);
>>> + v |= PRCI_DEVICESRESETREG_GEMGXL_RST_N_MASK;
>>> + __prci_writel(v, PRCI_DEVICESRESETREG_OFFSET, pd);
>>> +
>>> + /* Procmon => core clock */
>>> + __prci_writel(PRCI_PROCMONCFG_CORE_CLOCK_MASK,
>>PRCI_PROCMONCFG_OFFSET,
>>> + pd);
>>> +}
>>> +#endif
>>> +
>>> static int sifive_fu540_prci_probe(struct udevice *dev) {
>>> int i, err;
>>> @@ -687,6 +758,10 @@ static int sifive_fu540_prci_probe(struct
>>> udevice
>>*dev)
>>> __prci_wrpll_read_cfg0(pd, pc->pwd);
>>> }
>>>
>>> +#ifdef CONFIG_SPL_BUILD
>>> + ethernet_init(dev);
>>> +#endif
>>> +
>>> return 0;
>>> }
>>
>>Regards,
>>Bin
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 01/22] misc: add driver for the SiFive otp controller
2020-05-02 16:18 ` Pragnesh Patel
@ 2020-05-10 9:04 ` Jagan Teki
2020-05-11 5:39 ` Pragnesh Patel
0 siblings, 1 reply; 118+ messages in thread
From: Jagan Teki @ 2020-05-10 9:04 UTC (permalink / raw)
To: u-boot
On Sat, May 2, 2020 at 9:48 PM Pragnesh Patel <pragnesh.patel@sifive.com> wrote:
>
> Hi Jagan,
>
> >-----Original Message-----
> >From: Jagan Teki <jagan@amarulasolutions.com>
> >Sent: 02 May 2020 21:21
> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> ><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Bin
> >Meng <bmeng.cn@gmail.com>; Paul Walmsley <paul.walmsley@sifive.com>;
> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
> ><rick@andestech.com>; Tero Kristo <t-kristo@ti.com>; Simon Glass
> ><sjg@chromium.org>; Adam Ford <aford173@gmail.com>; Eugen Hristev
> ><eugen.hristev@microchip.com>; Peng Fan <peng.fan@nxp.com>; Finley Xiao
> ><finley.xiao@rock-chips.com>; Kever Yang <kever.yang@rock-chips.com>
> >Subject: Re: [PATCH v7 01/22] misc: add driver for the SiFive otp controller
> >
> >[External Email] Do not click links or attachments unless you recognize the
> >sender and know the content is safe
> >
> >On Sat, May 2, 2020 at 9:12 PM Pragnesh Patel <pragnesh.patel@sifive.com>
> >wrote:
> >>
> >> Hi Jagan,
> >>
> >> >-----Original Message-----
> >> >From: Jagan Teki <jagan@amarulasolutions.com>
> >> >Sent: 02 May 2020 21:07
> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> >> ><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>;
> >Bin
> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
> ><paul.walmsley@sifive.com>;
> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> >> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick
> >Chen
> >> ><rick@andestech.com>; Tero Kristo <t-kristo@ti.com>; Simon Glass
> >> ><sjg@chromium.org>; Adam Ford <aford173@gmail.com>; Eugen Hristev
> >> ><eugen.hristev@microchip.com>; Peng Fan <peng.fan@nxp.com>; Finley
> >> >Xiao <finley.xiao@rock-chips.com>; Kever Yang
> >> ><kever.yang@rock-chips.com>
> >> >Subject: Re: [PATCH v7 01/22] misc: add driver for the SiFive otp
> >> >controller
> >> >
> >> >[External Email] Do not click links or attachments unless you
> >> >recognize the sender and know the content is safe
> >> >
> >> >On Sat, May 2, 2020 at 3:37 PM Pragnesh Patel
> >> ><pragnesh.patel@sifive.com>
> >> >wrote:
> >> >>
> >> >> Added a misc driver to handle OTP memory in SiFive SoCs.
> >> >>
> >> >> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> >> ---
> >> >> drivers/misc/Kconfig | 7 +
> >> >> drivers/misc/Makefile | 1 +
> >> >> drivers/misc/sifive-otp.c | 273
> >> >> ++++++++++++++++++++++++++++++++++++++
> >> >> 3 files changed, 281 insertions(+) create mode 100644
> >> >> drivers/misc/sifive-otp.c
> >> >>
> >> >> diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig index
> >> >> 766402745d..03464f1010 100644
> >> >> --- a/drivers/misc/Kconfig
> >> >> +++ b/drivers/misc/Kconfig
> >> >> @@ -68,6 +68,13 @@ config ROCKCHIP_OTP
> >> >> addressing and a length or through child-nodes that are generated
> >> >> based on the e-fuse map retrieved from the DTS.
> >> >>
> >> >> +config SIFIVE_OTP
> >> >> + bool "SiFive eMemory OTP driver"
> >> >> + depends on RISCV && MISC
> >> >
> >> >This can be something like this.
> >> >
> >> >config SIFIVE_OTP
> >> > bool "SiFive eMemory OTP driver"
> >> > depends on SIFIVE_FU540
> >>
> >> This config option is not FU540 specific but it's for all SiFive SoCs.
> >
> >Well RISCV is not SIFIVE, better add SIFIVE_FU540 as of now if you have more
> >SoC's in future will update by adding one more or add new symbol SIFIVE.
>
> IMHO it's better not to make it SoC specific, Board Kconfig file will imply this option if needed.
> This is something we follow for FU540.
>
> SIFIVE_OTP is depends on SIFIVE SoCs and all SIFIVE SoCs are RISCV specific that's why I added
> depends on RISCV.
Well not all RISCV SoC's are SiFive, since you have SIFIVE_FU540 now
add depends for now rest will follow similar or common config item for
SiFive socs in future. Check any driver in drivers or drivers/misc it
is common notation.
Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 14/22] riscv: Add place-holder for driver compilation
2020-05-03 9:17 ` Pragnesh Patel
@ 2020-05-10 9:12 ` Jagan Teki
2020-05-11 5:58 ` Pragnesh Patel
0 siblings, 1 reply; 118+ messages in thread
From: Jagan Teki @ 2020-05-10 9:12 UTC (permalink / raw)
To: u-boot
On Sun, May 3, 2020 at 2:47 PM Pragnesh Patel <pragnesh.patel@sifive.com> wrote:
>
> Hi Jagan,
>
> >-----Original Message-----
> >From: Jagan Teki <jagan@amarulasolutions.com>
> >Sent: 02 May 2020 21:58
> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> ><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Bin
> >Meng <bmeng.cn@gmail.com>; Paul Walmsley <paul.walmsley@sifive.com>;
> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
> ><rick@andestech.com>
> >Subject: Re: [PATCH v7 14/22] riscv: Add place-holder for driver compilation
> >
> >[External Email] Do not click links or attachments unless you recognize the
> >sender and know the content is safe
> >
> >On Sat, May 2, 2020 at 3:38 PM Pragnesh Patel <pragnesh.patel@sifive.com>
> >wrote:
> >>
> >> Add place-holder for RISC-V fu540 CPU
> >>
> >> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> ---
> >> arch/riscv/include/asm/arch-fu540/clk.h | 14 +++++++++
> >> arch/riscv/include/asm/arch-fu540/gpio.h | 38 ++++++++++++++++++++++++
> >
> >Where is it using exactly?
>
> "drivers/gpio/sifive-gpio.c"
I mean which patch used these headers?
Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
2020-05-03 7:27 ` Pragnesh Patel
@ 2020-05-10 9:31 ` Jagan Teki
2020-05-11 6:05 ` Pragnesh Patel
0 siblings, 1 reply; 118+ messages in thread
From: Jagan Teki @ 2020-05-10 9:31 UTC (permalink / raw)
To: u-boot
On Sun, May 3, 2020 at 12:57 PM Pragnesh Patel
<pragnesh.patel@sifive.com> wrote:
>
> Hi jagan,
>
> >-----Original Message-----
> >From: Jagan Teki <jagan@amarulasolutions.com>
> >Sent: 02 May 2020 22:43
> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> ><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Bin
> >Meng <bmeng.cn@gmail.com>; Paul Walmsley <paul.walmsley@sifive.com>;
> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
> ><rick@andestech.com>
> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
> >
> >[External Email] Do not click links or attachments unless you recognize the
> >sender and know the content is safe
> >
> >On Sat, May 2, 2020 at 10:12 PM Pragnesh Patel <pragnesh.patel@sifive.com>
> >wrote:
> >>
> >> Hi Jagan,
> >>
> >> >-----Original Message-----
> >> >From: Jagan Teki <jagan@amarulasolutions.com>
> >> >Sent: 02 May 2020 21:49
> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> >> ><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>;
> >Bin
> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
> ><paul.walmsley@sifive.com>;
> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> >> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick
> >Chen
> >> ><rick@andestech.com>
> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in
> >> >U-Boot
> >> >
> >> >[External Email] Do not click links or attachments unless you
> >> >recognize the sender and know the content is safe
> >> >
> >> >On Sat, May 2, 2020 at 3:39 PM Pragnesh Patel
> >> ><pragnesh.patel@sifive.com>
> >> >wrote:
> >> >>
> >> >> Add L2 cache node to enable cache ways from U-Boot
> >> >
> >> >This and 20/22 doesn't relate to SPL MMC boot?, if yes please send
> >> >them separately.
> >>
> >> This series is for replacing FSBL and all the patches are related to that.
> >> IMHO it's better to add all FSBL functionality in one series.
> >
> >You mean does it break existing FSBL flow? if yes add proper commit message,
> >but I am able to boot SPL MMC w/o this?
>
> Cache ways are enabled by FSBL also and if I will send cache ways patches separately then it will a duplicate
> way of enabling cache ways if someone using FSBL.
Sorry I didn't get you.
If we cannot include these changes does U-Boot SPL break existing FSBL?
Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 01/22] misc: add driver for the SiFive otp controller
2020-05-10 9:04 ` Jagan Teki
@ 2020-05-11 5:39 ` Pragnesh Patel
0 siblings, 0 replies; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-11 5:39 UTC (permalink / raw)
To: u-boot
>-----Original Message-----
>From: Jagan Teki <jagan@amarulasolutions.com>
>Sent: 10 May 2020 14:34
>To: Pragnesh Patel <pragnesh.patel@sifive.com>
>Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Bin
>Meng <bmeng.cn@gmail.com>; Paul Walmsley <paul.walmsley@sifive.com>;
>Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
><rick@andestech.com>; Tero Kristo <t-kristo@ti.com>; Simon Glass
><sjg@chromium.org>; Adam Ford <aford173@gmail.com>; Eugen Hristev
><eugen.hristev@microchip.com>; Peng Fan <peng.fan@nxp.com>; Finley Xiao
><finley.xiao@rock-chips.com>; Kever Yang <kever.yang@rock-chips.com>
>Subject: Re: [PATCH v7 01/22] misc: add driver for the SiFive otp controller
>
>[External Email] Do not click links or attachments unless you recognize the
>sender and know the content is safe
>
>On Sat, May 2, 2020 at 9:48 PM Pragnesh Patel <pragnesh.patel@sifive.com>
>wrote:
>>
>> Hi Jagan,
>>
>> >-----Original Message-----
>> >From: Jagan Teki <jagan@amarulasolutions.com>
>> >Sent: 02 May 2020 21:21
>> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
>> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
>> ><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>;
>Bin
>> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
><paul.walmsley@sifive.com>;
>> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
>> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick
>Chen
>> ><rick@andestech.com>; Tero Kristo <t-kristo@ti.com>; Simon Glass
>> ><sjg@chromium.org>; Adam Ford <aford173@gmail.com>; Eugen Hristev
>> ><eugen.hristev@microchip.com>; Peng Fan <peng.fan@nxp.com>; Finley
>> >Xiao <finley.xiao@rock-chips.com>; Kever Yang
>> ><kever.yang@rock-chips.com>
>> >Subject: Re: [PATCH v7 01/22] misc: add driver for the SiFive otp
>> >controller
>> >
>> >[External Email] Do not click links or attachments unless you
>> >recognize the sender and know the content is safe
>> >
>> >On Sat, May 2, 2020 at 9:12 PM Pragnesh Patel
>> ><pragnesh.patel@sifive.com>
>> >wrote:
>> >>
>> >> Hi Jagan,
>> >>
>> >> >-----Original Message-----
>> >> >From: Jagan Teki <jagan@amarulasolutions.com>
>> >> >Sent: 02 May 2020 21:07
>> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
>> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
>> >> ><atish.patra@wdc.com>; Palmer Dabbelt
><palmerdabbelt@google.com>;
>> >Bin
>> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
>> ><paul.walmsley@sifive.com>;
>> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
>> >> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick
>> >Chen
>> >> ><rick@andestech.com>; Tero Kristo <t-kristo@ti.com>; Simon Glass
>> >> ><sjg@chromium.org>; Adam Ford <aford173@gmail.com>; Eugen
>Hristev
>> >> ><eugen.hristev@microchip.com>; Peng Fan <peng.fan@nxp.com>;
>Finley
>> >> >Xiao <finley.xiao@rock-chips.com>; Kever Yang
>> >> ><kever.yang@rock-chips.com>
>> >> >Subject: Re: [PATCH v7 01/22] misc: add driver for the SiFive otp
>> >> >controller
>> >> >
>> >> >[External Email] Do not click links or attachments unless you
>> >> >recognize the sender and know the content is safe
>> >> >
>> >> >On Sat, May 2, 2020 at 3:37 PM Pragnesh Patel
>> >> ><pragnesh.patel@sifive.com>
>> >> >wrote:
>> >> >>
>> >> >> Added a misc driver to handle OTP memory in SiFive SoCs.
>> >> >>
>> >> >> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
>> >> >> ---
>> >> >> drivers/misc/Kconfig | 7 +
>> >> >> drivers/misc/Makefile | 1 +
>> >> >> drivers/misc/sifive-otp.c | 273
>> >> >> ++++++++++++++++++++++++++++++++++++++
>> >> >> 3 files changed, 281 insertions(+) create mode 100644
>> >> >> drivers/misc/sifive-otp.c
>> >> >>
>> >> >> diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig index
>> >> >> 766402745d..03464f1010 100644
>> >> >> --- a/drivers/misc/Kconfig
>> >> >> +++ b/drivers/misc/Kconfig
>> >> >> @@ -68,6 +68,13 @@ config ROCKCHIP_OTP
>> >> >> addressing and a length or through child-nodes that are
>generated
>> >> >> based on the e-fuse map retrieved from the DTS.
>> >> >>
>> >> >> +config SIFIVE_OTP
>> >> >> + bool "SiFive eMemory OTP driver"
>> >> >> + depends on RISCV && MISC
>> >> >
>> >> >This can be something like this.
>> >> >
>> >> >config SIFIVE_OTP
>> >> > bool "SiFive eMemory OTP driver"
>> >> > depends on SIFIVE_FU540
>> >>
>> >> This config option is not FU540 specific but it's for all SiFive SoCs.
>> >
>> >Well RISCV is not SIFIVE, better add SIFIVE_FU540 as of now if you
>> >have more SoC's in future will update by adding one more or add new
>symbol SIFIVE.
>>
>> IMHO it's better not to make it SoC specific, Board Kconfig file will imply this
>option if needed.
>> This is something we follow for FU540.
>>
>> SIFIVE_OTP is depends on SIFIVE SoCs and all SIFIVE SoCs are RISCV
>> specific that's why I added depends on RISCV.
>
>Well not all RISCV SoC's are SiFive, since you have SIFIVE_FU540 now add
>depends for now rest will follow similar or common config item for SiFive socs
>in future. Check any driver in drivers or drivers/misc it is common notation.
Already remove the depends on RISCV in v8.
Making a common config for SiFive SoCs is good option that we will do in future and that common
Kconfig will imply or select all the necessary config option.
If you will see, other Kconfig in drivers/misc then they are not depend on SoC but SoC config (configs/**defconfig) file
Will select it.
Ideally, SIFIVE_OTP is also not depends on SIFIVE_FU540 so it's better to select or implied SIFIVE_OTP by board Kconfig.
Right now, SIFIVE_OTP is implied by "board/sifive/fu540/Kconfig".
>
>Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 14/22] riscv: Add place-holder for driver compilation
2020-05-10 9:12 ` Jagan Teki
@ 2020-05-11 5:58 ` Pragnesh Patel
2020-05-11 6:53 ` Jagan Teki
0 siblings, 1 reply; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-11 5:58 UTC (permalink / raw)
To: u-boot
>-----Original Message-----
>From: Jagan Teki <jagan@amarulasolutions.com>
>Sent: 10 May 2020 14:42
>To: Pragnesh Patel <pragnesh.patel@sifive.com>
>Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Bin
>Meng <bmeng.cn@gmail.com>; Paul Walmsley <paul.walmsley@sifive.com>;
>Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
><rick@andestech.com>
>Subject: Re: [PATCH v7 14/22] riscv: Add place-holder for driver compilation
>
>[External Email] Do not click links or attachments unless you recognize the
>sender and know the content is safe
>
>On Sun, May 3, 2020 at 2:47 PM Pragnesh Patel <pragnesh.patel@sifive.com>
>wrote:
>>
>> Hi Jagan,
>>
>> >-----Original Message-----
>> >From: Jagan Teki <jagan@amarulasolutions.com>
>> >Sent: 02 May 2020 21:58
>> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
>> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
>> ><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>;
>Bin
>> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
><paul.walmsley@sifive.com>;
>> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
>> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick
>Chen
>> ><rick@andestech.com>
>> >Subject: Re: [PATCH v7 14/22] riscv: Add place-holder for driver
>> >compilation
>> >
>> >[External Email] Do not click links or attachments unless you
>> >recognize the sender and know the content is safe
>> >
>> >On Sat, May 2, 2020 at 3:38 PM Pragnesh Patel
>> ><pragnesh.patel@sifive.com>
>> >wrote:
>> >>
>> >> Add place-holder for RISC-V fu540 CPU
>> >>
>> >> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
>> >> ---
>> >> arch/riscv/include/asm/arch-fu540/clk.h | 14 +++++++++
>> >> arch/riscv/include/asm/arch-fu540/gpio.h | 38
>> >> ++++++++++++++++++++++++
>> >
>> >Where is it using exactly?
>>
>> "drivers/gpio/sifive-gpio.c"
>
>I mean which patch used these headers?
This headers are necessary for existing SiFive drivers.
Earlier CONFIG_SYS_CPU is "generic", so drivers use headers from " arch/riscv/include/asm/arch-generic/" now
We have changed the CONFIG_SYS_CPU to "fu540" so now drivers will use headers from
"arch/riscv/include/asm/arch-fu540/".
>
>Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
2020-05-10 9:31 ` Jagan Teki
@ 2020-05-11 6:05 ` Pragnesh Patel
2020-05-11 6:54 ` Jagan Teki
0 siblings, 1 reply; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-11 6:05 UTC (permalink / raw)
To: u-boot
>-----Original Message-----
>From: Jagan Teki <jagan@amarulasolutions.com>
>Sent: 10 May 2020 15:02
>To: Pragnesh Patel <pragnesh.patel@sifive.com>
>Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Bin
>Meng <bmeng.cn@gmail.com>; Paul Walmsley <paul.walmsley@sifive.com>;
>Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
><rick@andestech.com>
>Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
>
>[External Email] Do not click links or attachments unless you recognize the
>sender and know the content is safe
>
>On Sun, May 3, 2020 at 12:57 PM Pragnesh Patel
><pragnesh.patel@sifive.com> wrote:
>>
>> Hi jagan,
>>
>> >-----Original Message-----
>> >From: Jagan Teki <jagan@amarulasolutions.com>
>> >Sent: 02 May 2020 22:43
>> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
>> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
>> ><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>;
>Bin
>> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
><paul.walmsley@sifive.com>;
>> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
>> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick
>Chen
>> ><rick@andestech.com>
>> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in
>> >U-Boot
>> >
>> >[External Email] Do not click links or attachments unless you
>> >recognize the sender and know the content is safe
>> >
>> >On Sat, May 2, 2020 at 10:12 PM Pragnesh Patel
>> ><pragnesh.patel@sifive.com>
>> >wrote:
>> >>
>> >> Hi Jagan,
>> >>
>> >> >-----Original Message-----
>> >> >From: Jagan Teki <jagan@amarulasolutions.com>
>> >> >Sent: 02 May 2020 21:49
>> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
>> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
>> >> ><atish.patra@wdc.com>; Palmer Dabbelt
><palmerdabbelt@google.com>;
>> >Bin
>> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
>> ><paul.walmsley@sifive.com>;
>> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
>> >> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick
>> >Chen
>> >> ><rick@andestech.com>
>> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache
>> >> >in U-Boot
>> >> >
>> >> >[External Email] Do not click links or attachments unless you
>> >> >recognize the sender and know the content is safe
>> >> >
>> >> >On Sat, May 2, 2020 at 3:39 PM Pragnesh Patel
>> >> ><pragnesh.patel@sifive.com>
>> >> >wrote:
>> >> >>
>> >> >> Add L2 cache node to enable cache ways from U-Boot
>> >> >
>> >> >This and 20/22 doesn't relate to SPL MMC boot?, if yes please send
>> >> >them separately.
>> >>
>> >> This series is for replacing FSBL and all the patches are related to that.
>> >> IMHO it's better to add all FSBL functionality in one series.
>> >
>> >You mean does it break existing FSBL flow? if yes add proper commit
>> >message, but I am able to boot SPL MMC w/o this?
>>
>> Cache ways are enabled by FSBL also and if I will send cache ways
>> patches separately then it will a duplicate way of enabling cache ways if
>someone using FSBL.
>
>Sorry I didn't get you.
>
>If we cannot include these changes does U-Boot SPL break existing FSBL?
No, U-Boot SPL does not break without this.
As of now, we also want to support FSBL flow and FSBL also enabled the Cache ways for U-Boot
proper and if someone use this patches of L2 cache enable ways will FSBL then it will be a duplicate
work of cache enable ways.
>
>Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 14/22] riscv: Add place-holder for driver compilation
2020-05-11 5:58 ` Pragnesh Patel
@ 2020-05-11 6:53 ` Jagan Teki
2020-05-11 7:10 ` Pragnesh Patel
0 siblings, 1 reply; 118+ messages in thread
From: Jagan Teki @ 2020-05-11 6:53 UTC (permalink / raw)
To: u-boot
On Mon, May 11, 2020 at 11:28 AM Pragnesh Patel
<pragnesh.patel@sifive.com> wrote:
>
> >-----Original Message-----
> >From: Jagan Teki <jagan@amarulasolutions.com>
> >Sent: 10 May 2020 14:42
> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> ><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Bin
> >Meng <bmeng.cn@gmail.com>; Paul Walmsley <paul.walmsley@sifive.com>;
> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
> ><rick@andestech.com>
> >Subject: Re: [PATCH v7 14/22] riscv: Add place-holder for driver compilation
> >
> >[External Email] Do not click links or attachments unless you recognize the
> >sender and know the content is safe
> >
> >On Sun, May 3, 2020 at 2:47 PM Pragnesh Patel <pragnesh.patel@sifive.com>
> >wrote:
> >>
> >> Hi Jagan,
> >>
> >> >-----Original Message-----
> >> >From: Jagan Teki <jagan@amarulasolutions.com>
> >> >Sent: 02 May 2020 21:58
> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> >> ><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>;
> >Bin
> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
> ><paul.walmsley@sifive.com>;
> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> >> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick
> >Chen
> >> ><rick@andestech.com>
> >> >Subject: Re: [PATCH v7 14/22] riscv: Add place-holder for driver
> >> >compilation
> >> >
> >> >[External Email] Do not click links or attachments unless you
> >> >recognize the sender and know the content is safe
> >> >
> >> >On Sat, May 2, 2020 at 3:38 PM Pragnesh Patel
> >> ><pragnesh.patel@sifive.com>
> >> >wrote:
> >> >>
> >> >> Add place-holder for RISC-V fu540 CPU
> >> >>
> >> >> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> >> ---
> >> >> arch/riscv/include/asm/arch-fu540/clk.h | 14 +++++++++
> >> >> arch/riscv/include/asm/arch-fu540/gpio.h | 38
> >> >> ++++++++++++++++++++++++
> >> >
> >> >Where is it using exactly?
> >>
> >> "drivers/gpio/sifive-gpio.c"
> >
> >I mean which patch used these headers?
>
> This headers are necessary for existing SiFive drivers.
>
> Earlier CONFIG_SYS_CPU is "generic", so drivers use headers from " arch/riscv/include/asm/arch-generic/" now
> We have changed the CONFIG_SYS_CPU to "fu540" so now drivers will use headers from
> "arch/riscv/include/asm/arch-fu540/".
How can someone understand the patch if you don't have any commit
message explaining this? also add these headers to the patch that
introduces CONFIG_SYS_CPU. It makes more sense to use the code or
header which are relevant rather than a stale commit.
Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
2020-05-11 6:05 ` Pragnesh Patel
@ 2020-05-11 6:54 ` Jagan Teki
2020-05-11 7:07 ` Pragnesh Patel
0 siblings, 1 reply; 118+ messages in thread
From: Jagan Teki @ 2020-05-11 6:54 UTC (permalink / raw)
To: u-boot
On Mon, May 11, 2020 at 11:35 AM Pragnesh Patel
<pragnesh.patel@sifive.com> wrote:
>
> >-----Original Message-----
> >From: Jagan Teki <jagan@amarulasolutions.com>
> >Sent: 10 May 2020 15:02
> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> ><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Bin
> >Meng <bmeng.cn@gmail.com>; Paul Walmsley <paul.walmsley@sifive.com>;
> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
> ><rick@andestech.com>
> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
> >
> >[External Email] Do not click links or attachments unless you recognize the
> >sender and know the content is safe
> >
> >On Sun, May 3, 2020 at 12:57 PM Pragnesh Patel
> ><pragnesh.patel@sifive.com> wrote:
> >>
> >> Hi jagan,
> >>
> >> >-----Original Message-----
> >> >From: Jagan Teki <jagan@amarulasolutions.com>
> >> >Sent: 02 May 2020 22:43
> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> >> ><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>;
> >Bin
> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
> ><paul.walmsley@sifive.com>;
> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> >> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick
> >Chen
> >> ><rick@andestech.com>
> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in
> >> >U-Boot
> >> >
> >> >[External Email] Do not click links or attachments unless you
> >> >recognize the sender and know the content is safe
> >> >
> >> >On Sat, May 2, 2020 at 10:12 PM Pragnesh Patel
> >> ><pragnesh.patel@sifive.com>
> >> >wrote:
> >> >>
> >> >> Hi Jagan,
> >> >>
> >> >> >-----Original Message-----
> >> >> >From: Jagan Teki <jagan@amarulasolutions.com>
> >> >> >Sent: 02 May 2020 21:49
> >> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> >> >> ><atish.patra@wdc.com>; Palmer Dabbelt
> ><palmerdabbelt@google.com>;
> >> >Bin
> >> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
> >> ><paul.walmsley@sifive.com>;
> >> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> >> >> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick
> >> >Chen
> >> >> ><rick@andestech.com>
> >> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache
> >> >> >in U-Boot
> >> >> >
> >> >> >[External Email] Do not click links or attachments unless you
> >> >> >recognize the sender and know the content is safe
> >> >> >
> >> >> >On Sat, May 2, 2020 at 3:39 PM Pragnesh Patel
> >> >> ><pragnesh.patel@sifive.com>
> >> >> >wrote:
> >> >> >>
> >> >> >> Add L2 cache node to enable cache ways from U-Boot
> >> >> >
> >> >> >This and 20/22 doesn't relate to SPL MMC boot?, if yes please send
> >> >> >them separately.
> >> >>
> >> >> This series is for replacing FSBL and all the patches are related to that.
> >> >> IMHO it's better to add all FSBL functionality in one series.
> >> >
> >> >You mean does it break existing FSBL flow? if yes add proper commit
> >> >message, but I am able to boot SPL MMC w/o this?
> >>
> >> Cache ways are enabled by FSBL also and if I will send cache ways
> >> patches separately then it will a duplicate way of enabling cache ways if
> >someone using FSBL.
> >
> >Sorry I didn't get you.
> >
> >If we cannot include these changes does U-Boot SPL break existing FSBL?
>
> No, U-Boot SPL does not break without this.
>
> As of now, we also want to support FSBL flow and FSBL also enabled the Cache ways for U-Boot
> proper and if someone use this patches of L2 cache enable ways will FSBL then it will be a duplicate
> work of cache enable ways.
My question is what if we don't add this change at all?
Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
2020-05-11 6:54 ` Jagan Teki
@ 2020-05-11 7:07 ` Pragnesh Patel
2020-05-11 7:25 ` Jagan Teki
0 siblings, 1 reply; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-11 7:07 UTC (permalink / raw)
To: u-boot
>-----Original Message-----
>From: Jagan Teki <jagan@amarulasolutions.com>
>Sent: 11 May 2020 12:25
>To: Pragnesh Patel <pragnesh.patel@sifive.com>
>Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Bin
>Meng <bmeng.cn@gmail.com>; Paul Walmsley <paul.walmsley@sifive.com>;
>Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
><rick@andestech.com>
>Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
>
>[External Email] Do not click links or attachments unless you recognize the
>sender and know the content is safe
>
>On Mon, May 11, 2020 at 11:35 AM Pragnesh Patel
><pragnesh.patel@sifive.com> wrote:
>>
>> >-----Original Message-----
>> >From: Jagan Teki <jagan@amarulasolutions.com>
>> >Sent: 10 May 2020 15:02
>> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
>> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
>> ><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>;
>Bin
>> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
><paul.walmsley@sifive.com>;
>> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
>> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick
>Chen
>> ><rick@andestech.com>
>> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in
>> >U-Boot
>> >
>> >[External Email] Do not click links or attachments unless you
>> >recognize the sender and know the content is safe
>> >
>> >On Sun, May 3, 2020 at 12:57 PM Pragnesh Patel
>> ><pragnesh.patel@sifive.com> wrote:
>> >>
>> >> Hi jagan,
>> >>
>> >> >-----Original Message-----
>> >> >From: Jagan Teki <jagan@amarulasolutions.com>
>> >> >Sent: 02 May 2020 22:43
>> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
>> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
>> >> ><atish.patra@wdc.com>; Palmer Dabbelt
><palmerdabbelt@google.com>;
>> >Bin
>> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
>> ><paul.walmsley@sifive.com>;
>> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
>> >> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick
>> >Chen
>> >> ><rick@andestech.com>
>> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache
>> >> >in U-Boot
>> >> >
>> >> >[External Email] Do not click links or attachments unless you
>> >> >recognize the sender and know the content is safe
>> >> >
>> >> >On Sat, May 2, 2020 at 10:12 PM Pragnesh Patel
>> >> ><pragnesh.patel@sifive.com>
>> >> >wrote:
>> >> >>
>> >> >> Hi Jagan,
>> >> >>
>> >> >> >-----Original Message-----
>> >> >> >From: Jagan Teki <jagan@amarulasolutions.com>
>> >> >> >Sent: 02 May 2020 21:49
>> >> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
>> >> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
>> >> >> ><atish.patra@wdc.com>; Palmer Dabbelt
>> ><palmerdabbelt@google.com>;
>> >> >Bin
>> >> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
>> >> ><paul.walmsley@sifive.com>;
>> >> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
>> >> >> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>;
>> >> >> >Rick
>> >> >Chen
>> >> >> ><rick@andestech.com>
>> >> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2
>> >> >> >Cache in U-Boot
>> >> >> >
>> >> >> >[External Email] Do not click links or attachments unless you
>> >> >> >recognize the sender and know the content is safe
>> >> >> >
>> >> >> >On Sat, May 2, 2020 at 3:39 PM Pragnesh Patel
>> >> >> ><pragnesh.patel@sifive.com>
>> >> >> >wrote:
>> >> >> >>
>> >> >> >> Add L2 cache node to enable cache ways from U-Boot
>> >> >> >
>> >> >> >This and 20/22 doesn't relate to SPL MMC boot?, if yes please
>> >> >> >send them separately.
>> >> >>
>> >> >> This series is for replacing FSBL and all the patches are related to that.
>> >> >> IMHO it's better to add all FSBL functionality in one series.
>> >> >
>> >> >You mean does it break existing FSBL flow? if yes add proper
>> >> >commit message, but I am able to boot SPL MMC w/o this?
>> >>
>> >> Cache ways are enabled by FSBL also and if I will send cache ways
>> >> patches separately then it will a duplicate way of enabling cache
>> >> ways if
>> >someone using FSBL.
>> >
>> >Sorry I didn't get you.
>> >
>> >If we cannot include these changes does U-Boot SPL break existing FSBL?
>>
>> No, U-Boot SPL does not break without this.
>>
>> As of now, we also want to support FSBL flow and FSBL also enabled the
>> Cache ways for U-Boot proper and if someone use this patches of L2
>> cache enable ways will FSBL then it will be a duplicate work of cache enable
>ways.
>
>My question is what if we don't add this change at all?
U-Boot SPL will work without L2 cache enable patches but why we want to do this.
This series is not just for SPL mmc booting but also replacing FSBL functionality so better to cover
all FSBL stuff in one series.
I am not in favour of pulling out L2 cache patches out of this series.
>
>Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 14/22] riscv: Add place-holder for driver compilation
2020-05-11 6:53 ` Jagan Teki
@ 2020-05-11 7:10 ` Pragnesh Patel
0 siblings, 0 replies; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-11 7:10 UTC (permalink / raw)
To: u-boot
>-----Original Message-----
>From: Jagan Teki <jagan@amarulasolutions.com>
>Sent: 11 May 2020 12:23
>To: Pragnesh Patel <pragnesh.patel@sifive.com>
>Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Bin
>Meng <bmeng.cn@gmail.com>; Paul Walmsley <paul.walmsley@sifive.com>;
>Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
><rick@andestech.com>
>Subject: Re: [PATCH v7 14/22] riscv: Add place-holder for driver compilation
>
>[External Email] Do not click links or attachments unless you recognize the
>sender and know the content is safe
>
>On Mon, May 11, 2020 at 11:28 AM Pragnesh Patel
><pragnesh.patel@sifive.com> wrote:
>>
>> >-----Original Message-----
>> >From: Jagan Teki <jagan@amarulasolutions.com>
>> >Sent: 10 May 2020 14:42
>> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
>> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
>> ><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>;
>Bin
>> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
><paul.walmsley@sifive.com>;
>> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
>> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick
>Chen
>> ><rick@andestech.com>
>> >Subject: Re: [PATCH v7 14/22] riscv: Add place-holder for driver
>> >compilation
>> >
>> >[External Email] Do not click links or attachments unless you
>> >recognize the sender and know the content is safe
>> >
>> >On Sun, May 3, 2020 at 2:47 PM Pragnesh Patel
>> ><pragnesh.patel@sifive.com>
>> >wrote:
>> >>
>> >> Hi Jagan,
>> >>
>> >> >-----Original Message-----
>> >> >From: Jagan Teki <jagan@amarulasolutions.com>
>> >> >Sent: 02 May 2020 21:58
>> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
>> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
>> >> ><atish.patra@wdc.com>; Palmer Dabbelt
><palmerdabbelt@google.com>;
>> >Bin
>> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
>> ><paul.walmsley@sifive.com>;
>> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
>> >> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick
>> >Chen
>> >> ><rick@andestech.com>
>> >> >Subject: Re: [PATCH v7 14/22] riscv: Add place-holder for driver
>> >> >compilation
>> >> >
>> >> >[External Email] Do not click links or attachments unless you
>> >> >recognize the sender and know the content is safe
>> >> >
>> >> >On Sat, May 2, 2020 at 3:38 PM Pragnesh Patel
>> >> ><pragnesh.patel@sifive.com>
>> >> >wrote:
>> >> >>
>> >> >> Add place-holder for RISC-V fu540 CPU
>> >> >>
>> >> >> Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
>> >> >> ---
>> >> >> arch/riscv/include/asm/arch-fu540/clk.h | 14 +++++++++
>> >> >> arch/riscv/include/asm/arch-fu540/gpio.h | 38
>> >> >> ++++++++++++++++++++++++
>> >> >
>> >> >Where is it using exactly?
>> >>
>> >> "drivers/gpio/sifive-gpio.c"
>> >
>> >I mean which patch used these headers?
>>
>> This headers are necessary for existing SiFive drivers.
>>
>> Earlier CONFIG_SYS_CPU is "generic", so drivers use headers from "
>> arch/riscv/include/asm/arch-generic/" now We have changed the
>> CONFIG_SYS_CPU to "fu540" so now drivers will use headers from
>"arch/riscv/include/asm/arch-fu540/".
>
>How can someone understand the patch if you don't have any commit
>message explaining this? also add these headers to the patch that introduces
>CONFIG_SYS_CPU. It makes more sense to use the code or header which are
>relevant rather than a stale commit.
Okay, I will squash [v7 13/22] and [v7 14/22] and also change CONFIG_SYS_CPU to
"fu540" in that patch.
>
>Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
2020-05-11 7:07 ` Pragnesh Patel
@ 2020-05-11 7:25 ` Jagan Teki
2020-05-11 7:45 ` Pragnesh Patel
0 siblings, 1 reply; 118+ messages in thread
From: Jagan Teki @ 2020-05-11 7:25 UTC (permalink / raw)
To: u-boot
On Mon, May 11, 2020 at 12:37 PM Pragnesh Patel
<pragnesh.patel@sifive.com> wrote:
>
> >-----Original Message-----
> >From: Jagan Teki <jagan@amarulasolutions.com>
> >Sent: 11 May 2020 12:25
> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> ><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Bin
> >Meng <bmeng.cn@gmail.com>; Paul Walmsley <paul.walmsley@sifive.com>;
> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
> ><rick@andestech.com>
> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
> >
> >[External Email] Do not click links or attachments unless you recognize the
> >sender and know the content is safe
> >
> >On Mon, May 11, 2020 at 11:35 AM Pragnesh Patel
> ><pragnesh.patel@sifive.com> wrote:
> >>
> >> >-----Original Message-----
> >> >From: Jagan Teki <jagan@amarulasolutions.com>
> >> >Sent: 10 May 2020 15:02
> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> >> ><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>;
> >Bin
> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
> ><paul.walmsley@sifive.com>;
> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> >> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick
> >Chen
> >> ><rick@andestech.com>
> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in
> >> >U-Boot
> >> >
> >> >[External Email] Do not click links or attachments unless you
> >> >recognize the sender and know the content is safe
> >> >
> >> >On Sun, May 3, 2020 at 12:57 PM Pragnesh Patel
> >> ><pragnesh.patel@sifive.com> wrote:
> >> >>
> >> >> Hi jagan,
> >> >>
> >> >> >-----Original Message-----
> >> >> >From: Jagan Teki <jagan@amarulasolutions.com>
> >> >> >Sent: 02 May 2020 22:43
> >> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> >> >> ><atish.patra@wdc.com>; Palmer Dabbelt
> ><palmerdabbelt@google.com>;
> >> >Bin
> >> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
> >> ><paul.walmsley@sifive.com>;
> >> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> >> >> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick
> >> >Chen
> >> >> ><rick@andestech.com>
> >> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache
> >> >> >in U-Boot
> >> >> >
> >> >> >[External Email] Do not click links or attachments unless you
> >> >> >recognize the sender and know the content is safe
> >> >> >
> >> >> >On Sat, May 2, 2020 at 10:12 PM Pragnesh Patel
> >> >> ><pragnesh.patel@sifive.com>
> >> >> >wrote:
> >> >> >>
> >> >> >> Hi Jagan,
> >> >> >>
> >> >> >> >-----Original Message-----
> >> >> >> >From: Jagan Teki <jagan@amarulasolutions.com>
> >> >> >> >Sent: 02 May 2020 21:49
> >> >> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> >> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> >> >> >> ><atish.patra@wdc.com>; Palmer Dabbelt
> >> ><palmerdabbelt@google.com>;
> >> >> >Bin
> >> >> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
> >> >> ><paul.walmsley@sifive.com>;
> >> >> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> >> >> >> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>;
> >> >> >> >Rick
> >> >> >Chen
> >> >> >> ><rick@andestech.com>
> >> >> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2
> >> >> >> >Cache in U-Boot
> >> >> >> >
> >> >> >> >[External Email] Do not click links or attachments unless you
> >> >> >> >recognize the sender and know the content is safe
> >> >> >> >
> >> >> >> >On Sat, May 2, 2020 at 3:39 PM Pragnesh Patel
> >> >> >> ><pragnesh.patel@sifive.com>
> >> >> >> >wrote:
> >> >> >> >>
> >> >> >> >> Add L2 cache node to enable cache ways from U-Boot
> >> >> >> >
> >> >> >> >This and 20/22 doesn't relate to SPL MMC boot?, if yes please
> >> >> >> >send them separately.
> >> >> >>
> >> >> >> This series is for replacing FSBL and all the patches are related to that.
> >> >> >> IMHO it's better to add all FSBL functionality in one series.
> >> >> >
> >> >> >You mean does it break existing FSBL flow? if yes add proper
> >> >> >commit message, but I am able to boot SPL MMC w/o this?
> >> >>
> >> >> Cache ways are enabled by FSBL also and if I will send cache ways
> >> >> patches separately then it will a duplicate way of enabling cache
> >> >> ways if
> >> >someone using FSBL.
> >> >
> >> >Sorry I didn't get you.
> >> >
> >> >If we cannot include these changes does U-Boot SPL break existing FSBL?
> >>
> >> No, U-Boot SPL does not break without this.
> >>
> >> As of now, we also want to support FSBL flow and FSBL also enabled the
> >> Cache ways for U-Boot proper and if someone use this patches of L2
> >> cache enable ways will FSBL then it will be a duplicate work of cache enable
> >ways.
> >
> >My question is what if we don't add this change at all?
>
> U-Boot SPL will work without L2 cache enable patches but why we want to do this.
> This series is not just for SPL mmc booting but also replacing FSBL functionality so better to cover
> all FSBL stuff in one series.
So, FSBL flow would break if we add U-Boot SPL so this patch fixing by
enabling cache's explicitly to avoid that break. isn't it?
Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
2020-05-11 7:25 ` Jagan Teki
@ 2020-05-11 7:45 ` Pragnesh Patel
2020-05-11 8:48 ` Jagan Teki
0 siblings, 1 reply; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-11 7:45 UTC (permalink / raw)
To: u-boot
>-----Original Message-----
>From: Jagan Teki <jagan@amarulasolutions.com>
>Sent: 11 May 2020 12:56
>To: Pragnesh Patel <pragnesh.patel@sifive.com>
>Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Bin
>Meng <bmeng.cn@gmail.com>; Paul Walmsley <paul.walmsley@sifive.com>;
>Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
><rick@andestech.com>
>Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
>
>[External Email] Do not click links or attachments unless you recognize the
>sender and know the content is safe
>
>On Mon, May 11, 2020 at 12:37 PM Pragnesh Patel
><pragnesh.patel@sifive.com> wrote:
>>
>> >-----Original Message-----
>> >From: Jagan Teki <jagan@amarulasolutions.com>
>> >Sent: 11 May 2020 12:25
>> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
>> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
>> ><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>;
>Bin
>> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
><paul.walmsley@sifive.com>;
>> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
>> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick
>Chen
>> ><rick@andestech.com>
>> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in
>> >U-Boot
>> >
>> >[External Email] Do not click links or attachments unless you
>> >recognize the sender and know the content is safe
>> >
>> >On Mon, May 11, 2020 at 11:35 AM Pragnesh Patel
>> ><pragnesh.patel@sifive.com> wrote:
>> >>
>> >> >-----Original Message-----
>> >> >From: Jagan Teki <jagan@amarulasolutions.com>
>> >> >Sent: 10 May 2020 15:02
>> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
>> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
>> >> ><atish.patra@wdc.com>; Palmer Dabbelt
><palmerdabbelt@google.com>;
>> >Bin
>> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
>> ><paul.walmsley@sifive.com>;
>> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
>> >> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick
>> >Chen
>> >> ><rick@andestech.com>
>> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache
>> >> >in U-Boot
>> >> >
>> >> >[External Email] Do not click links or attachments unless you
>> >> >recognize the sender and know the content is safe
>> >> >
>> >> >On Sun, May 3, 2020 at 12:57 PM Pragnesh Patel
>> >> ><pragnesh.patel@sifive.com> wrote:
>> >> >>
>> >> >> Hi jagan,
>> >> >>
>> >> >> >-----Original Message-----
>> >> >> >From: Jagan Teki <jagan@amarulasolutions.com>
>> >> >> >Sent: 02 May 2020 22:43
>> >> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
>> >> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
>> >> >> ><atish.patra@wdc.com>; Palmer Dabbelt
>> ><palmerdabbelt@google.com>;
>> >> >Bin
>> >> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
>> >> ><paul.walmsley@sifive.com>;
>> >> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
>> >> >> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>;
>> >> >> >Rick
>> >> >Chen
>> >> >> ><rick@andestech.com>
>> >> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2
>> >> >> >Cache in U-Boot
>> >> >> >
>> >> >> >[External Email] Do not click links or attachments unless you
>> >> >> >recognize the sender and know the content is safe
>> >> >> >
>> >> >> >On Sat, May 2, 2020 at 10:12 PM Pragnesh Patel
>> >> >> ><pragnesh.patel@sifive.com>
>> >> >> >wrote:
>> >> >> >>
>> >> >> >> Hi Jagan,
>> >> >> >>
>> >> >> >> >-----Original Message-----
>> >> >> >> >From: Jagan Teki <jagan@amarulasolutions.com>
>> >> >> >> >Sent: 02 May 2020 21:49
>> >> >> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
>> >> >> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
>> >> >> >> ><atish.patra@wdc.com>; Palmer Dabbelt
>> >> ><palmerdabbelt@google.com>;
>> >> >> >Bin
>> >> >> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
>> >> >> ><paul.walmsley@sifive.com>;
>> >> >> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
>> >> >> >> ><anup.patel@wdc.com>; Sagar Kadam
><sagar.kadam@sifive.com>;
>> >> >> >> >Rick
>> >> >> >Chen
>> >> >> >> ><rick@andestech.com>
>> >> >> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2
>> >> >> >> >Cache in U-Boot
>> >> >> >> >
>> >> >> >> >[External Email] Do not click links or attachments unless
>> >> >> >> >you recognize the sender and know the content is safe
>> >> >> >> >
>> >> >> >> >On Sat, May 2, 2020 at 3:39 PM Pragnesh Patel
>> >> >> >> ><pragnesh.patel@sifive.com>
>> >> >> >> >wrote:
>> >> >> >> >>
>> >> >> >> >> Add L2 cache node to enable cache ways from U-Boot
>> >> >> >> >
>> >> >> >> >This and 20/22 doesn't relate to SPL MMC boot?, if yes
>> >> >> >> >please send them separately.
>> >> >> >>
>> >> >> >> This series is for replacing FSBL and all the patches are related to
>that.
>> >> >> >> IMHO it's better to add all FSBL functionality in one series.
>> >> >> >
>> >> >> >You mean does it break existing FSBL flow? if yes add proper
>> >> >> >commit message, but I am able to boot SPL MMC w/o this?
>> >> >>
>> >> >> Cache ways are enabled by FSBL also and if I will send cache
>> >> >> ways patches separately then it will a duplicate way of enabling
>> >> >> cache ways if
>> >> >someone using FSBL.
>> >> >
>> >> >Sorry I didn't get you.
>> >> >
>> >> >If we cannot include these changes does U-Boot SPL break existing FSBL?
>> >>
>> >> No, U-Boot SPL does not break without this.
>> >>
>> >> As of now, we also want to support FSBL flow and FSBL also enabled
>> >> the Cache ways for U-Boot proper and if someone use this patches of
>> >> L2 cache enable ways will FSBL then it will be a duplicate work of
>> >> cache enable
>> >ways.
>> >
>> >My question is what if we don't add this change at all?
>>
>> U-Boot SPL will work without L2 cache enable patches but why we want to
>do this.
>> This series is not just for SPL mmc booting but also replacing FSBL
>> functionality so better to cover all FSBL stuff in one series.
>
>So, FSBL flow would break if we add U-Boot SPL so this patch fixing by enabling
>cache's explicitly to avoid that break. isn't it?
No, you are not getting this.
Initially FSBL enable the cache ways before U-Boot SPL.
https://github.com/sifive/freedom-u540-c000-bootloader/blob/master/fsbl/main.c#L428
Now U-Boot SPL doing the same in [v7 19/22] and [v7 20/22].
User can use U-Boot SPL or FSBL anyone at a time as a bootloader, so better to replace all FSBL
stuff in one series.
>
>Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
2020-05-11 7:45 ` Pragnesh Patel
@ 2020-05-11 8:48 ` Jagan Teki
2020-05-11 9:00 ` Bin Meng
0 siblings, 1 reply; 118+ messages in thread
From: Jagan Teki @ 2020-05-11 8:48 UTC (permalink / raw)
To: u-boot
On Mon, May 11, 2020 at 1:15 PM Pragnesh Patel
<pragnesh.patel@sifive.com> wrote:
>
> >-----Original Message-----
> >From: Jagan Teki <jagan@amarulasolutions.com>
> >Sent: 11 May 2020 12:56
> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> ><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Bin
> >Meng <bmeng.cn@gmail.com>; Paul Walmsley <paul.walmsley@sifive.com>;
> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
> ><rick@andestech.com>
> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
> >
> >[External Email] Do not click links or attachments unless you recognize the
> >sender and know the content is safe
> >
> >On Mon, May 11, 2020 at 12:37 PM Pragnesh Patel
> ><pragnesh.patel@sifive.com> wrote:
> >>
> >> >-----Original Message-----
> >> >From: Jagan Teki <jagan@amarulasolutions.com>
> >> >Sent: 11 May 2020 12:25
> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> >> ><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>;
> >Bin
> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
> ><paul.walmsley@sifive.com>;
> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> >> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick
> >Chen
> >> ><rick@andestech.com>
> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in
> >> >U-Boot
> >> >
> >> >[External Email] Do not click links or attachments unless you
> >> >recognize the sender and know the content is safe
> >> >
> >> >On Mon, May 11, 2020 at 11:35 AM Pragnesh Patel
> >> ><pragnesh.patel@sifive.com> wrote:
> >> >>
> >> >> >-----Original Message-----
> >> >> >From: Jagan Teki <jagan@amarulasolutions.com>
> >> >> >Sent: 10 May 2020 15:02
> >> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> >> >> ><atish.patra@wdc.com>; Palmer Dabbelt
> ><palmerdabbelt@google.com>;
> >> >Bin
> >> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
> >> ><paul.walmsley@sifive.com>;
> >> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> >> >> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick
> >> >Chen
> >> >> ><rick@andestech.com>
> >> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache
> >> >> >in U-Boot
> >> >> >
> >> >> >[External Email] Do not click links or attachments unless you
> >> >> >recognize the sender and know the content is safe
> >> >> >
> >> >> >On Sun, May 3, 2020 at 12:57 PM Pragnesh Patel
> >> >> ><pragnesh.patel@sifive.com> wrote:
> >> >> >>
> >> >> >> Hi jagan,
> >> >> >>
> >> >> >> >-----Original Message-----
> >> >> >> >From: Jagan Teki <jagan@amarulasolutions.com>
> >> >> >> >Sent: 02 May 2020 22:43
> >> >> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> >> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> >> >> >> ><atish.patra@wdc.com>; Palmer Dabbelt
> >> ><palmerdabbelt@google.com>;
> >> >> >Bin
> >> >> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
> >> >> ><paul.walmsley@sifive.com>;
> >> >> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> >> >> >> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>;
> >> >> >> >Rick
> >> >> >Chen
> >> >> >> ><rick@andestech.com>
> >> >> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2
> >> >> >> >Cache in U-Boot
> >> >> >> >
> >> >> >> >[External Email] Do not click links or attachments unless you
> >> >> >> >recognize the sender and know the content is safe
> >> >> >> >
> >> >> >> >On Sat, May 2, 2020 at 10:12 PM Pragnesh Patel
> >> >> >> ><pragnesh.patel@sifive.com>
> >> >> >> >wrote:
> >> >> >> >>
> >> >> >> >> Hi Jagan,
> >> >> >> >>
> >> >> >> >> >-----Original Message-----
> >> >> >> >> >From: Jagan Teki <jagan@amarulasolutions.com>
> >> >> >> >> >Sent: 02 May 2020 21:49
> >> >> >> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> >> >> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> >> >> >> >> ><atish.patra@wdc.com>; Palmer Dabbelt
> >> >> ><palmerdabbelt@google.com>;
> >> >> >> >Bin
> >> >> >> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
> >> >> >> ><paul.walmsley@sifive.com>;
> >> >> >> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> >> >> >> >> ><anup.patel@wdc.com>; Sagar Kadam
> ><sagar.kadam@sifive.com>;
> >> >> >> >> >Rick
> >> >> >> >Chen
> >> >> >> >> ><rick@andestech.com>
> >> >> >> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2
> >> >> >> >> >Cache in U-Boot
> >> >> >> >> >
> >> >> >> >> >[External Email] Do not click links or attachments unless
> >> >> >> >> >you recognize the sender and know the content is safe
> >> >> >> >> >
> >> >> >> >> >On Sat, May 2, 2020 at 3:39 PM Pragnesh Patel
> >> >> >> >> ><pragnesh.patel@sifive.com>
> >> >> >> >> >wrote:
> >> >> >> >> >>
> >> >> >> >> >> Add L2 cache node to enable cache ways from U-Boot
> >> >> >> >> >
> >> >> >> >> >This and 20/22 doesn't relate to SPL MMC boot?, if yes
> >> >> >> >> >please send them separately.
> >> >> >> >>
> >> >> >> >> This series is for replacing FSBL and all the patches are related to
> >that.
> >> >> >> >> IMHO it's better to add all FSBL functionality in one series.
> >> >> >> >
> >> >> >> >You mean does it break existing FSBL flow? if yes add proper
> >> >> >> >commit message, but I am able to boot SPL MMC w/o this?
> >> >> >>
> >> >> >> Cache ways are enabled by FSBL also and if I will send cache
> >> >> >> ways patches separately then it will a duplicate way of enabling
> >> >> >> cache ways if
> >> >> >someone using FSBL.
> >> >> >
> >> >> >Sorry I didn't get you.
> >> >> >
> >> >> >If we cannot include these changes does U-Boot SPL break existing FSBL?
> >> >>
> >> >> No, U-Boot SPL does not break without this.
> >> >>
> >> >> As of now, we also want to support FSBL flow and FSBL also enabled
> >> >> the Cache ways for U-Boot proper and if someone use this patches of
> >> >> L2 cache enable ways will FSBL then it will be a duplicate work of
> >> >> cache enable
> >> >ways.
> >> >
> >> >My question is what if we don't add this change at all?
> >>
> >> U-Boot SPL will work without L2 cache enable patches but why we want to
> >do this.
> >> This series is not just for SPL mmc booting but also replacing FSBL
> >> functionality so better to cover all FSBL stuff in one series.
> >
> >So, FSBL flow would break if we add U-Boot SPL so this patch fixing by enabling
> >cache's explicitly to avoid that break. isn't it?
>
> No, you are not getting this.
>
> Initially FSBL enable the cache ways before U-Boot SPL.
> https://github.com/sifive/freedom-u540-c000-bootloader/blob/master/fsbl/main.c#L428
This is not Mainline. enabling cache's are a new thing for Mainline
for you. So this code is pretty much new. Is that clear?
>
> Now U-Boot SPL doing the same in [v7 19/22] and [v7 20/22].
But these two patches enable caches for U-Boot proper in case of
U-Boot SPL flow and U-Boot in case of FSBL. am I correct? if so this
code is purely U-Boot specific neither FSBL nor U-Boot SPL. then what
is the problem of having a series or separate patches with cache
enablement.
Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
2020-05-11 8:48 ` Jagan Teki
@ 2020-05-11 9:00 ` Bin Meng
2020-05-11 9:05 ` Jagan Teki
0 siblings, 1 reply; 118+ messages in thread
From: Bin Meng @ 2020-05-11 9:00 UTC (permalink / raw)
To: u-boot
Hi Jagan,
On Mon, May 11, 2020 at 4:48 PM Jagan Teki <jagan@amarulasolutions.com> wrote:
>
> On Mon, May 11, 2020 at 1:15 PM Pragnesh Patel
> <pragnesh.patel@sifive.com> wrote:
> >
> > >-----Original Message-----
> > >From: Jagan Teki <jagan@amarulasolutions.com>
> > >Sent: 11 May 2020 12:56
> > >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> > >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> > ><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Bin
> > >Meng <bmeng.cn@gmail.com>; Paul Walmsley <paul.walmsley@sifive.com>;
> > >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> > ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
> > ><rick@andestech.com>
> > >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
> > >
> > >[External Email] Do not click links or attachments unless you recognize the
> > >sender and know the content is safe
> > >
> > >On Mon, May 11, 2020 at 12:37 PM Pragnesh Patel
> > ><pragnesh.patel@sifive.com> wrote:
> > >>
> > >> >-----Original Message-----
> > >> >From: Jagan Teki <jagan@amarulasolutions.com>
> > >> >Sent: 11 May 2020 12:25
> > >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> > >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> > >> ><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>;
> > >Bin
> > >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
> > ><paul.walmsley@sifive.com>;
> > >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> > >> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick
> > >Chen
> > >> ><rick@andestech.com>
> > >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in
> > >> >U-Boot
> > >> >
> > >> >[External Email] Do not click links or attachments unless you
> > >> >recognize the sender and know the content is safe
> > >> >
> > >> >On Mon, May 11, 2020 at 11:35 AM Pragnesh Patel
> > >> ><pragnesh.patel@sifive.com> wrote:
> > >> >>
> > >> >> >-----Original Message-----
> > >> >> >From: Jagan Teki <jagan@amarulasolutions.com>
> > >> >> >Sent: 10 May 2020 15:02
> > >> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> > >> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> > >> >> ><atish.patra@wdc.com>; Palmer Dabbelt
> > ><palmerdabbelt@google.com>;
> > >> >Bin
> > >> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
> > >> ><paul.walmsley@sifive.com>;
> > >> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> > >> >> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick
> > >> >Chen
> > >> >> ><rick@andestech.com>
> > >> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache
> > >> >> >in U-Boot
> > >> >> >
> > >> >> >[External Email] Do not click links or attachments unless you
> > >> >> >recognize the sender and know the content is safe
> > >> >> >
> > >> >> >On Sun, May 3, 2020 at 12:57 PM Pragnesh Patel
> > >> >> ><pragnesh.patel@sifive.com> wrote:
> > >> >> >>
> > >> >> >> Hi jagan,
> > >> >> >>
> > >> >> >> >-----Original Message-----
> > >> >> >> >From: Jagan Teki <jagan@amarulasolutions.com>
> > >> >> >> >Sent: 02 May 2020 22:43
> > >> >> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> > >> >> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> > >> >> >> ><atish.patra@wdc.com>; Palmer Dabbelt
> > >> ><palmerdabbelt@google.com>;
> > >> >> >Bin
> > >> >> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
> > >> >> ><paul.walmsley@sifive.com>;
> > >> >> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> > >> >> >> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>;
> > >> >> >> >Rick
> > >> >> >Chen
> > >> >> >> ><rick@andestech.com>
> > >> >> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2
> > >> >> >> >Cache in U-Boot
> > >> >> >> >
> > >> >> >> >[External Email] Do not click links or attachments unless you
> > >> >> >> >recognize the sender and know the content is safe
> > >> >> >> >
> > >> >> >> >On Sat, May 2, 2020 at 10:12 PM Pragnesh Patel
> > >> >> >> ><pragnesh.patel@sifive.com>
> > >> >> >> >wrote:
> > >> >> >> >>
> > >> >> >> >> Hi Jagan,
> > >> >> >> >>
> > >> >> >> >> >-----Original Message-----
> > >> >> >> >> >From: Jagan Teki <jagan@amarulasolutions.com>
> > >> >> >> >> >Sent: 02 May 2020 21:49
> > >> >> >> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> > >> >> >> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> > >> >> >> >> ><atish.patra@wdc.com>; Palmer Dabbelt
> > >> >> ><palmerdabbelt@google.com>;
> > >> >> >> >Bin
> > >> >> >> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
> > >> >> >> ><paul.walmsley@sifive.com>;
> > >> >> >> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> > >> >> >> >> ><anup.patel@wdc.com>; Sagar Kadam
> > ><sagar.kadam@sifive.com>;
> > >> >> >> >> >Rick
> > >> >> >> >Chen
> > >> >> >> >> ><rick@andestech.com>
> > >> >> >> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2
> > >> >> >> >> >Cache in U-Boot
> > >> >> >> >> >
> > >> >> >> >> >[External Email] Do not click links or attachments unless
> > >> >> >> >> >you recognize the sender and know the content is safe
> > >> >> >> >> >
> > >> >> >> >> >On Sat, May 2, 2020 at 3:39 PM Pragnesh Patel
> > >> >> >> >> ><pragnesh.patel@sifive.com>
> > >> >> >> >> >wrote:
> > >> >> >> >> >>
> > >> >> >> >> >> Add L2 cache node to enable cache ways from U-Boot
> > >> >> >> >> >
> > >> >> >> >> >This and 20/22 doesn't relate to SPL MMC boot?, if yes
> > >> >> >> >> >please send them separately.
> > >> >> >> >>
> > >> >> >> >> This series is for replacing FSBL and all the patches are related to
> > >that.
> > >> >> >> >> IMHO it's better to add all FSBL functionality in one series.
> > >> >> >> >
> > >> >> >> >You mean does it break existing FSBL flow? if yes add proper
> > >> >> >> >commit message, but I am able to boot SPL MMC w/o this?
> > >> >> >>
> > >> >> >> Cache ways are enabled by FSBL also and if I will send cache
> > >> >> >> ways patches separately then it will a duplicate way of enabling
> > >> >> >> cache ways if
> > >> >> >someone using FSBL.
> > >> >> >
> > >> >> >Sorry I didn't get you.
> > >> >> >
> > >> >> >If we cannot include these changes does U-Boot SPL break existing FSBL?
> > >> >>
> > >> >> No, U-Boot SPL does not break without this.
> > >> >>
> > >> >> As of now, we also want to support FSBL flow and FSBL also enabled
> > >> >> the Cache ways for U-Boot proper and if someone use this patches of
> > >> >> L2 cache enable ways will FSBL then it will be a duplicate work of
> > >> >> cache enable
> > >> >ways.
> > >> >
> > >> >My question is what if we don't add this change at all?
> > >>
> > >> U-Boot SPL will work without L2 cache enable patches but why we want to
> > >do this.
> > >> This series is not just for SPL mmc booting but also replacing FSBL
> > >> functionality so better to cover all FSBL stuff in one series.
> > >
> > >So, FSBL flow would break if we add U-Boot SPL so this patch fixing by enabling
> > >cache's explicitly to avoid that break. isn't it?
> >
> > No, you are not getting this.
> >
> > Initially FSBL enable the cache ways before U-Boot SPL.
> > https://github.com/sifive/freedom-u540-c000-bootloader/blob/master/fsbl/main.c#L428
>
> This is not Mainline. enabling cache's are a new thing for Mainline
> for you. So this code is pretty much new. Is that clear?
>
> >
> > Now U-Boot SPL doing the same in [v7 19/22] and [v7 20/22].
>
> But these two patches enable caches for U-Boot proper in case of
> U-Boot SPL flow and U-Boot in case of FSBL. am I correct? if so this
> code is purely U-Boot specific neither FSBL nor U-Boot SPL. then what
> is the problem of having a series or separate patches with cache
> enablement.
My understanding is that:
1. This patch series is adding SiFive FU540 U-Boot SPL support
2. The purpose is to replace SiFive provided FSBL with U-Boot SPL
3. SiFive FSBL initializes L2 cache before loading next stage payload
4. U-Boot SPL should provide the same features, like initializing L2 cache
I don't think we should separate the patch to another series.
Regards,
Bin
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
2020-05-11 9:00 ` Bin Meng
@ 2020-05-11 9:05 ` Jagan Teki
2020-05-11 9:34 ` Pragnesh Patel
0 siblings, 1 reply; 118+ messages in thread
From: Jagan Teki @ 2020-05-11 9:05 UTC (permalink / raw)
To: u-boot
Hi Bin,
On Mon, May 11, 2020 at 2:30 PM Bin Meng <bmeng.cn@gmail.com> wrote:
>
> Hi Jagan,
>
> On Mon, May 11, 2020 at 4:48 PM Jagan Teki <jagan@amarulasolutions.com> wrote:
> >
> > On Mon, May 11, 2020 at 1:15 PM Pragnesh Patel
> > <pragnesh.patel@sifive.com> wrote:
> > >
> > > >-----Original Message-----
> > > >From: Jagan Teki <jagan@amarulasolutions.com>
> > > >Sent: 11 May 2020 12:56
> > > >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> > > >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> > > ><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>; Bin
> > > >Meng <bmeng.cn@gmail.com>; Paul Walmsley <paul.walmsley@sifive.com>;
> > > >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> > > ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
> > > ><rick@andestech.com>
> > > >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
> > > >
> > > >[External Email] Do not click links or attachments unless you recognize the
> > > >sender and know the content is safe
> > > >
> > > >On Mon, May 11, 2020 at 12:37 PM Pragnesh Patel
> > > ><pragnesh.patel@sifive.com> wrote:
> > > >>
> > > >> >-----Original Message-----
> > > >> >From: Jagan Teki <jagan@amarulasolutions.com>
> > > >> >Sent: 11 May 2020 12:25
> > > >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> > > >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> > > >> ><atish.patra@wdc.com>; Palmer Dabbelt <palmerdabbelt@google.com>;
> > > >Bin
> > > >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
> > > ><paul.walmsley@sifive.com>;
> > > >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> > > >> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick
> > > >Chen
> > > >> ><rick@andestech.com>
> > > >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in
> > > >> >U-Boot
> > > >> >
> > > >> >[External Email] Do not click links or attachments unless you
> > > >> >recognize the sender and know the content is safe
> > > >> >
> > > >> >On Mon, May 11, 2020 at 11:35 AM Pragnesh Patel
> > > >> ><pragnesh.patel@sifive.com> wrote:
> > > >> >>
> > > >> >> >-----Original Message-----
> > > >> >> >From: Jagan Teki <jagan@amarulasolutions.com>
> > > >> >> >Sent: 10 May 2020 15:02
> > > >> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> > > >> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> > > >> >> ><atish.patra@wdc.com>; Palmer Dabbelt
> > > ><palmerdabbelt@google.com>;
> > > >> >Bin
> > > >> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
> > > >> ><paul.walmsley@sifive.com>;
> > > >> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> > > >> >> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick
> > > >> >Chen
> > > >> >> ><rick@andestech.com>
> > > >> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache
> > > >> >> >in U-Boot
> > > >> >> >
> > > >> >> >[External Email] Do not click links or attachments unless you
> > > >> >> >recognize the sender and know the content is safe
> > > >> >> >
> > > >> >> >On Sun, May 3, 2020 at 12:57 PM Pragnesh Patel
> > > >> >> ><pragnesh.patel@sifive.com> wrote:
> > > >> >> >>
> > > >> >> >> Hi jagan,
> > > >> >> >>
> > > >> >> >> >-----Original Message-----
> > > >> >> >> >From: Jagan Teki <jagan@amarulasolutions.com>
> > > >> >> >> >Sent: 02 May 2020 22:43
> > > >> >> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> > > >> >> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> > > >> >> >> ><atish.patra@wdc.com>; Palmer Dabbelt
> > > >> ><palmerdabbelt@google.com>;
> > > >> >> >Bin
> > > >> >> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
> > > >> >> ><paul.walmsley@sifive.com>;
> > > >> >> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> > > >> >> >> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>;
> > > >> >> >> >Rick
> > > >> >> >Chen
> > > >> >> >> ><rick@andestech.com>
> > > >> >> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2
> > > >> >> >> >Cache in U-Boot
> > > >> >> >> >
> > > >> >> >> >[External Email] Do not click links or attachments unless you
> > > >> >> >> >recognize the sender and know the content is safe
> > > >> >> >> >
> > > >> >> >> >On Sat, May 2, 2020 at 10:12 PM Pragnesh Patel
> > > >> >> >> ><pragnesh.patel@sifive.com>
> > > >> >> >> >wrote:
> > > >> >> >> >>
> > > >> >> >> >> Hi Jagan,
> > > >> >> >> >>
> > > >> >> >> >> >-----Original Message-----
> > > >> >> >> >> >From: Jagan Teki <jagan@amarulasolutions.com>
> > > >> >> >> >> >Sent: 02 May 2020 21:49
> > > >> >> >> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> > > >> >> >> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> > > >> >> >> >> ><atish.patra@wdc.com>; Palmer Dabbelt
> > > >> >> ><palmerdabbelt@google.com>;
> > > >> >> >> >Bin
> > > >> >> >> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
> > > >> >> >> ><paul.walmsley@sifive.com>;
> > > >> >> >> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> > > >> >> >> >> ><anup.patel@wdc.com>; Sagar Kadam
> > > ><sagar.kadam@sifive.com>;
> > > >> >> >> >> >Rick
> > > >> >> >> >Chen
> > > >> >> >> >> ><rick@andestech.com>
> > > >> >> >> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2
> > > >> >> >> >> >Cache in U-Boot
> > > >> >> >> >> >
> > > >> >> >> >> >[External Email] Do not click links or attachments unless
> > > >> >> >> >> >you recognize the sender and know the content is safe
> > > >> >> >> >> >
> > > >> >> >> >> >On Sat, May 2, 2020 at 3:39 PM Pragnesh Patel
> > > >> >> >> >> ><pragnesh.patel@sifive.com>
> > > >> >> >> >> >wrote:
> > > >> >> >> >> >>
> > > >> >> >> >> >> Add L2 cache node to enable cache ways from U-Boot
> > > >> >> >> >> >
> > > >> >> >> >> >This and 20/22 doesn't relate to SPL MMC boot?, if yes
> > > >> >> >> >> >please send them separately.
> > > >> >> >> >>
> > > >> >> >> >> This series is for replacing FSBL and all the patches are related to
> > > >that.
> > > >> >> >> >> IMHO it's better to add all FSBL functionality in one series.
> > > >> >> >> >
> > > >> >> >> >You mean does it break existing FSBL flow? if yes add proper
> > > >> >> >> >commit message, but I am able to boot SPL MMC w/o this?
> > > >> >> >>
> > > >> >> >> Cache ways are enabled by FSBL also and if I will send cache
> > > >> >> >> ways patches separately then it will a duplicate way of enabling
> > > >> >> >> cache ways if
> > > >> >> >someone using FSBL.
> > > >> >> >
> > > >> >> >Sorry I didn't get you.
> > > >> >> >
> > > >> >> >If we cannot include these changes does U-Boot SPL break existing FSBL?
> > > >> >>
> > > >> >> No, U-Boot SPL does not break without this.
> > > >> >>
> > > >> >> As of now, we also want to support FSBL flow and FSBL also enabled
> > > >> >> the Cache ways for U-Boot proper and if someone use this patches of
> > > >> >> L2 cache enable ways will FSBL then it will be a duplicate work of
> > > >> >> cache enable
> > > >> >ways.
> > > >> >
> > > >> >My question is what if we don't add this change at all?
> > > >>
> > > >> U-Boot SPL will work without L2 cache enable patches but why we want to
> > > >do this.
> > > >> This series is not just for SPL mmc booting but also replacing FSBL
> > > >> functionality so better to cover all FSBL stuff in one series.
> > > >
> > > >So, FSBL flow would break if we add U-Boot SPL so this patch fixing by enabling
> > > >cache's explicitly to avoid that break. isn't it?
> > >
> > > No, you are not getting this.
> > >
> > > Initially FSBL enable the cache ways before U-Boot SPL.
> > > https://github.com/sifive/freedom-u540-c000-bootloader/blob/master/fsbl/main.c#L428
> >
> > This is not Mainline. enabling cache's are a new thing for Mainline
> > for you. So this code is pretty much new. Is that clear?
> >
> > >
> > > Now U-Boot SPL doing the same in [v7 19/22] and [v7 20/22].
> >
> > But these two patches enable caches for U-Boot proper in case of
> > U-Boot SPL flow and U-Boot in case of FSBL. am I correct? if so this
> > code is purely U-Boot specific neither FSBL nor U-Boot SPL. then what
> > is the problem of having a series or separate patches with cache
> > enablement.
>
> My understanding is that:
>
> 1. This patch series is adding SiFive FU540 U-Boot SPL support
> 2. The purpose is to replace SiFive provided FSBL with U-Boot SPL
> 3. SiFive FSBL initializes L2 cache before loading next stage payload
> 4. U-Boot SPL should provide the same features, like initializing L2 cache
So, you mean U-Boot SPL would enable the cache similar like FSBL does
right? but this patch [1] enabling cache only for U-Boot not SPL isn't
it?
[1] https://patchwork.ozlabs.org/project/uboot/patch/20200502100628.24809-20-pragnesh.patel at sifive.com/
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
2020-05-11 9:05 ` Jagan Teki
@ 2020-05-11 9:34 ` Pragnesh Patel
2020-05-11 9:47 ` Bin Meng
0 siblings, 1 reply; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-11 9:34 UTC (permalink / raw)
To: u-boot
>-----Original Message-----
>From: Jagan Teki <jagan@amarulasolutions.com>
>Sent: 11 May 2020 14:35
>To: Bin Meng <bmeng.cn@gmail.com>
>Cc: Pragnesh Patel <pragnesh.patel@sifive.com>; U-Boot-Denx <u-
>boot at lists.denx.de>; Atish Patra <atish.patra@wdc.com>; Palmer Dabbelt
><palmerdabbelt@google.com>; Paul Walmsley <paul.walmsley@sifive.com>;
>Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
><rick@andestech.com>
>Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
>
>[External Email] Do not click links or attachments unless you recognize the
>sender and know the content is safe
>
>Hi Bin,
>
>On Mon, May 11, 2020 at 2:30 PM Bin Meng <bmeng.cn@gmail.com> wrote:
>>
>> Hi Jagan,
>>
>> On Mon, May 11, 2020 at 4:48 PM Jagan Teki
><jagan@amarulasolutions.com> wrote:
>> >
>> > On Mon, May 11, 2020 at 1:15 PM Pragnesh Patel
>> > <pragnesh.patel@sifive.com> wrote:
>> > >
>> > > >-----Original Message-----
>> > > >From: Jagan Teki <jagan@amarulasolutions.com>
>> > > >Sent: 11 May 2020 12:56
>> > > >To: Pragnesh Patel <pragnesh.patel@sifive.com>
>> > > >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
>> > > ><atish.patra@wdc.com>; Palmer Dabbelt
><palmerdabbelt@google.com>;
>> > > >Bin Meng <bmeng.cn@gmail.com>; Paul Walmsley
>> > > ><paul.walmsley@sifive.com>; Troy Benjegerdes
>> > > ><troy.benjegerdes@sifive.com>; Anup Patel <anup.patel@wdc.com>;
>> > > >Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
>> > > ><rick@andestech.com>
>> > > >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache
>> > > >in U-Boot
>> > > >
>> > > >[External Email] Do not click links or attachments unless you
>> > > >recognize the sender and know the content is safe
>> > > >
>> > > >On Mon, May 11, 2020 at 12:37 PM Pragnesh Patel
>> > > ><pragnesh.patel@sifive.com> wrote:
>> > > >>
>> > > >> >-----Original Message-----
>> > > >> >From: Jagan Teki <jagan@amarulasolutions.com>
>> > > >> >Sent: 11 May 2020 12:25
>> > > >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
>> > > >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
>> > > >> ><atish.patra@wdc.com>; Palmer Dabbelt
>> > > >> ><palmerdabbelt@google.com>;
>> > > >Bin
>> > > >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
>> > > ><paul.walmsley@sifive.com>;
>> > > >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
>> > > >> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>;
>> > > >> >Rick
>> > > >Chen
>> > > >> ><rick@andestech.com>
>> > > >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2
>> > > >> >Cache in U-Boot
>> > > >> >
>> > > >> >[External Email] Do not click links or attachments unless you
>> > > >> >recognize the sender and know the content is safe
>> > > >> >
>> > > >> >On Mon, May 11, 2020 at 11:35 AM Pragnesh Patel
>> > > >> ><pragnesh.patel@sifive.com> wrote:
>> > > >> >>
>> > > >> >> >-----Original Message-----
>> > > >> >> >From: Jagan Teki <jagan@amarulasolutions.com>
>> > > >> >> >Sent: 10 May 2020 15:02
>> > > >> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
>> > > >> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
>> > > >> >> ><atish.patra@wdc.com>; Palmer Dabbelt
>> > > ><palmerdabbelt@google.com>;
>> > > >> >Bin
>> > > >> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
>> > > >> ><paul.walmsley@sifive.com>;
>> > > >> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
>> > > >> >> ><anup.patel@wdc.com>; Sagar Kadam
><sagar.kadam@sifive.com>;
>> > > >> >> >Rick
>> > > >> >Chen
>> > > >> >> ><rick@andestech.com>
>> > > >> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2
>> > > >> >> >Cache in U-Boot
>> > > >> >> >
>> > > >> >> >[External Email] Do not click links or attachments unless
>> > > >> >> >you recognize the sender and know the content is safe
>> > > >> >> >
>> > > >> >> >On Sun, May 3, 2020 at 12:57 PM Pragnesh Patel
>> > > >> >> ><pragnesh.patel@sifive.com> wrote:
>> > > >> >> >>
>> > > >> >> >> Hi jagan,
>> > > >> >> >>
>> > > >> >> >> >-----Original Message-----
>> > > >> >> >> >From: Jagan Teki <jagan@amarulasolutions.com>
>> > > >> >> >> >Sent: 02 May 2020 22:43
>> > > >> >> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
>> > > >> >> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
>> > > >> >> >> ><atish.patra@wdc.com>; Palmer Dabbelt
>> > > >> ><palmerdabbelt@google.com>;
>> > > >> >> >Bin
>> > > >> >> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
>> > > >> >> ><paul.walmsley@sifive.com>;
>> > > >> >> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup
>> > > >> >> >> >Patel <anup.patel@wdc.com>; Sagar Kadam
>> > > >> >> >> ><sagar.kadam@sifive.com>; Rick
>> > > >> >> >Chen
>> > > >> >> >> ><rick@andestech.com>
>> > > >> >> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable
>> > > >> >> >> >L2 Cache in U-Boot
>> > > >> >> >> >
>> > > >> >> >> >[External Email] Do not click links or attachments
>> > > >> >> >> >unless you recognize the sender and know the content is
>> > > >> >> >> >safe
>> > > >> >> >> >
>> > > >> >> >> >On Sat, May 2, 2020 at 10:12 PM Pragnesh Patel
>> > > >> >> >> ><pragnesh.patel@sifive.com>
>> > > >> >> >> >wrote:
>> > > >> >> >> >>
>> > > >> >> >> >> Hi Jagan,
>> > > >> >> >> >>
>> > > >> >> >> >> >-----Original Message-----
>> > > >> >> >> >> >From: Jagan Teki <jagan@amarulasolutions.com>
>> > > >> >> >> >> >Sent: 02 May 2020 21:49
>> > > >> >> >> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
>> > > >> >> >> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
>> > > >> >> >> >> ><atish.patra@wdc.com>; Palmer Dabbelt
>> > > >> >> ><palmerdabbelt@google.com>;
>> > > >> >> >> >Bin
>> > > >> >> >> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
>> > > >> >> >> ><paul.walmsley@sifive.com>;
>> > > >> >> >> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup
>> > > >> >> >> >> >Patel <anup.patel@wdc.com>; Sagar Kadam
>> > > ><sagar.kadam@sifive.com>;
>> > > >> >> >> >> >Rick
>> > > >> >> >> >Chen
>> > > >> >> >> >> ><rick@andestech.com>
>> > > >> >> >> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540:
>> > > >> >> >> >> >Enable L2 Cache in U-Boot
>> > > >> >> >> >> >
>> > > >> >> >> >> >[External Email] Do not click links or attachments
>> > > >> >> >> >> >unless you recognize the sender and know the content
>> > > >> >> >> >> >is safe
>> > > >> >> >> >> >
>> > > >> >> >> >> >On Sat, May 2, 2020 at 3:39 PM Pragnesh Patel
>> > > >> >> >> >> ><pragnesh.patel@sifive.com>
>> > > >> >> >> >> >wrote:
>> > > >> >> >> >> >>
>> > > >> >> >> >> >> Add L2 cache node to enable cache ways from U-Boot
>> > > >> >> >> >> >
>> > > >> >> >> >> >This and 20/22 doesn't relate to SPL MMC boot?, if
>> > > >> >> >> >> >yes please send them separately.
>> > > >> >> >> >>
>> > > >> >> >> >> This series is for replacing FSBL and all the patches
>> > > >> >> >> >> are related to
>> > > >that.
>> > > >> >> >> >> IMHO it's better to add all FSBL functionality in one series.
>> > > >> >> >> >
>> > > >> >> >> >You mean does it break existing FSBL flow? if yes add
>> > > >> >> >> >proper commit message, but I am able to boot SPL MMC w/o
>this?
>> > > >> >> >>
>> > > >> >> >> Cache ways are enabled by FSBL also and if I will send
>> > > >> >> >> cache ways patches separately then it will a duplicate
>> > > >> >> >> way of enabling cache ways if
>> > > >> >> >someone using FSBL.
>> > > >> >> >
>> > > >> >> >Sorry I didn't get you.
>> > > >> >> >
>> > > >> >> >If we cannot include these changes does U-Boot SPL break existing
>FSBL?
>> > > >> >>
>> > > >> >> No, U-Boot SPL does not break without this.
>> > > >> >>
>> > > >> >> As of now, we also want to support FSBL flow and FSBL also
>> > > >> >> enabled the Cache ways for U-Boot proper and if someone use
>> > > >> >> this patches of
>> > > >> >> L2 cache enable ways will FSBL then it will be a duplicate
>> > > >> >> work of cache enable
>> > > >> >ways.
>> > > >> >
>> > > >> >My question is what if we don't add this change at all?
>> > > >>
>> > > >> U-Boot SPL will work without L2 cache enable patches but why we
>> > > >> want to
>> > > >do this.
>> > > >> This series is not just for SPL mmc booting but also replacing
>> > > >> FSBL functionality so better to cover all FSBL stuff in one series.
>> > > >
>> > > >So, FSBL flow would break if we add U-Boot SPL so this patch
>> > > >fixing by enabling cache's explicitly to avoid that break. isn't it?
>> > >
>> > > No, you are not getting this.
>> > >
>> > > Initially FSBL enable the cache ways before U-Boot SPL.
>> > > https://github.com/sifive/freedom-u540-c000-bootloader/blob/master
>> > > /fsbl/main.c#L428
>> >
>> > This is not Mainline. enabling cache's are a new thing for Mainline
>> > for you. So this code is pretty much new. Is that clear?
>> >
>> > >
>> > > Now U-Boot SPL doing the same in [v7 19/22] and [v7 20/22].
>> >
>> > But these two patches enable caches for U-Boot proper in case of
>> > U-Boot SPL flow and U-Boot in case of FSBL. am I correct? if so this
>> > code is purely U-Boot specific neither FSBL nor U-Boot SPL. then
>> > what is the problem of having a series or separate patches with
>> > cache enablement.
>>
>> My understanding is that:
>>
>> 1. This patch series is adding SiFive FU540 U-Boot SPL support 2. The
>> purpose is to replace SiFive provided FSBL with U-Boot SPL 3. SiFive
>> FSBL initializes L2 cache before loading next stage payload 4. U-Boot
>> SPL should provide the same features, like initializing L2 cache
>
>So, you mean U-Boot SPL would enable the cache similar like FSBL does right?
>but this patch [1] enabling cache only for U-Boot not SPL isn't it?
>
>[1]
>https://patchwork.ozlabs.org/project/uboot/patch/20200502100628.24809-
>20-pragnesh.patel at sifive.com/
Yes, you are right. Cache ways are enabled by U-Boot proper not by U-Boot SPL.
Will pull cache related patches out of this series and send as separate patches.
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
2020-05-11 9:34 ` Pragnesh Patel
@ 2020-05-11 9:47 ` Bin Meng
2020-05-11 9:55 ` Pragnesh Patel
0 siblings, 1 reply; 118+ messages in thread
From: Bin Meng @ 2020-05-11 9:47 UTC (permalink / raw)
To: u-boot
Hi Pragnesh,
On Mon, May 11, 2020 at 5:34 PM Pragnesh Patel
<pragnesh.patel@sifive.com> wrote:
>
> >-----Original Message-----
> >From: Jagan Teki <jagan@amarulasolutions.com>
> >Sent: 11 May 2020 14:35
> >To: Bin Meng <bmeng.cn@gmail.com>
> >Cc: Pragnesh Patel <pragnesh.patel@sifive.com>; U-Boot-Denx <u-
> >boot at lists.denx.de>; Atish Patra <atish.patra@wdc.com>; Palmer Dabbelt
> ><palmerdabbelt@google.com>; Paul Walmsley <paul.walmsley@sifive.com>;
> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
> ><rick@andestech.com>
> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
> >
> >[External Email] Do not click links or attachments unless you recognize the
> >sender and know the content is safe
> >
> >Hi Bin,
> >
> >On Mon, May 11, 2020 at 2:30 PM Bin Meng <bmeng.cn@gmail.com> wrote:
> >>
> >> Hi Jagan,
> >>
> >> On Mon, May 11, 2020 at 4:48 PM Jagan Teki
> ><jagan@amarulasolutions.com> wrote:
> >> >
> >> > On Mon, May 11, 2020 at 1:15 PM Pragnesh Patel
> >> > <pragnesh.patel@sifive.com> wrote:
> >> > >
> >> > > >-----Original Message-----
> >> > > >From: Jagan Teki <jagan@amarulasolutions.com>
> >> > > >Sent: 11 May 2020 12:56
> >> > > >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> > > >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> >> > > ><atish.patra@wdc.com>; Palmer Dabbelt
> ><palmerdabbelt@google.com>;
> >> > > >Bin Meng <bmeng.cn@gmail.com>; Paul Walmsley
> >> > > ><paul.walmsley@sifive.com>; Troy Benjegerdes
> >> > > ><troy.benjegerdes@sifive.com>; Anup Patel <anup.patel@wdc.com>;
> >> > > >Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
> >> > > ><rick@andestech.com>
> >> > > >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache
> >> > > >in U-Boot
> >> > > >
> >> > > >[External Email] Do not click links or attachments unless you
> >> > > >recognize the sender and know the content is safe
> >> > > >
> >> > > >On Mon, May 11, 2020 at 12:37 PM Pragnesh Patel
> >> > > ><pragnesh.patel@sifive.com> wrote:
> >> > > >>
> >> > > >> >-----Original Message-----
> >> > > >> >From: Jagan Teki <jagan@amarulasolutions.com>
> >> > > >> >Sent: 11 May 2020 12:25
> >> > > >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> > > >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> >> > > >> ><atish.patra@wdc.com>; Palmer Dabbelt
> >> > > >> ><palmerdabbelt@google.com>;
> >> > > >Bin
> >> > > >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
> >> > > ><paul.walmsley@sifive.com>;
> >> > > >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> >> > > >> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>;
> >> > > >> >Rick
> >> > > >Chen
> >> > > >> ><rick@andestech.com>
> >> > > >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2
> >> > > >> >Cache in U-Boot
> >> > > >> >
> >> > > >> >[External Email] Do not click links or attachments unless you
> >> > > >> >recognize the sender and know the content is safe
> >> > > >> >
> >> > > >> >On Mon, May 11, 2020 at 11:35 AM Pragnesh Patel
> >> > > >> ><pragnesh.patel@sifive.com> wrote:
> >> > > >> >>
> >> > > >> >> >-----Original Message-----
> >> > > >> >> >From: Jagan Teki <jagan@amarulasolutions.com>
> >> > > >> >> >Sent: 10 May 2020 15:02
> >> > > >> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> > > >> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> >> > > >> >> ><atish.patra@wdc.com>; Palmer Dabbelt
> >> > > ><palmerdabbelt@google.com>;
> >> > > >> >Bin
> >> > > >> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
> >> > > >> ><paul.walmsley@sifive.com>;
> >> > > >> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> >> > > >> >> ><anup.patel@wdc.com>; Sagar Kadam
> ><sagar.kadam@sifive.com>;
> >> > > >> >> >Rick
> >> > > >> >Chen
> >> > > >> >> ><rick@andestech.com>
> >> > > >> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2
> >> > > >> >> >Cache in U-Boot
> >> > > >> >> >
> >> > > >> >> >[External Email] Do not click links or attachments unless
> >> > > >> >> >you recognize the sender and know the content is safe
> >> > > >> >> >
> >> > > >> >> >On Sun, May 3, 2020 at 12:57 PM Pragnesh Patel
> >> > > >> >> ><pragnesh.patel@sifive.com> wrote:
> >> > > >> >> >>
> >> > > >> >> >> Hi jagan,
> >> > > >> >> >>
> >> > > >> >> >> >-----Original Message-----
> >> > > >> >> >> >From: Jagan Teki <jagan@amarulasolutions.com>
> >> > > >> >> >> >Sent: 02 May 2020 22:43
> >> > > >> >> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> > > >> >> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> >> > > >> >> >> ><atish.patra@wdc.com>; Palmer Dabbelt
> >> > > >> ><palmerdabbelt@google.com>;
> >> > > >> >> >Bin
> >> > > >> >> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
> >> > > >> >> ><paul.walmsley@sifive.com>;
> >> > > >> >> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup
> >> > > >> >> >> >Patel <anup.patel@wdc.com>; Sagar Kadam
> >> > > >> >> >> ><sagar.kadam@sifive.com>; Rick
> >> > > >> >> >Chen
> >> > > >> >> >> ><rick@andestech.com>
> >> > > >> >> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable
> >> > > >> >> >> >L2 Cache in U-Boot
> >> > > >> >> >> >
> >> > > >> >> >> >[External Email] Do not click links or attachments
> >> > > >> >> >> >unless you recognize the sender and know the content is
> >> > > >> >> >> >safe
> >> > > >> >> >> >
> >> > > >> >> >> >On Sat, May 2, 2020 at 10:12 PM Pragnesh Patel
> >> > > >> >> >> ><pragnesh.patel@sifive.com>
> >> > > >> >> >> >wrote:
> >> > > >> >> >> >>
> >> > > >> >> >> >> Hi Jagan,
> >> > > >> >> >> >>
> >> > > >> >> >> >> >-----Original Message-----
> >> > > >> >> >> >> >From: Jagan Teki <jagan@amarulasolutions.com>
> >> > > >> >> >> >> >Sent: 02 May 2020 21:49
> >> > > >> >> >> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> > > >> >> >> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> >> > > >> >> >> >> ><atish.patra@wdc.com>; Palmer Dabbelt
> >> > > >> >> ><palmerdabbelt@google.com>;
> >> > > >> >> >> >Bin
> >> > > >> >> >> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
> >> > > >> >> >> ><paul.walmsley@sifive.com>;
> >> > > >> >> >> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup
> >> > > >> >> >> >> >Patel <anup.patel@wdc.com>; Sagar Kadam
> >> > > ><sagar.kadam@sifive.com>;
> >> > > >> >> >> >> >Rick
> >> > > >> >> >> >Chen
> >> > > >> >> >> >> ><rick@andestech.com>
> >> > > >> >> >> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540:
> >> > > >> >> >> >> >Enable L2 Cache in U-Boot
> >> > > >> >> >> >> >
> >> > > >> >> >> >> >[External Email] Do not click links or attachments
> >> > > >> >> >> >> >unless you recognize the sender and know the content
> >> > > >> >> >> >> >is safe
> >> > > >> >> >> >> >
> >> > > >> >> >> >> >On Sat, May 2, 2020 at 3:39 PM Pragnesh Patel
> >> > > >> >> >> >> ><pragnesh.patel@sifive.com>
> >> > > >> >> >> >> >wrote:
> >> > > >> >> >> >> >>
> >> > > >> >> >> >> >> Add L2 cache node to enable cache ways from U-Boot
> >> > > >> >> >> >> >
> >> > > >> >> >> >> >This and 20/22 doesn't relate to SPL MMC boot?, if
> >> > > >> >> >> >> >yes please send them separately.
> >> > > >> >> >> >>
> >> > > >> >> >> >> This series is for replacing FSBL and all the patches
> >> > > >> >> >> >> are related to
> >> > > >that.
> >> > > >> >> >> >> IMHO it's better to add all FSBL functionality in one series.
> >> > > >> >> >> >
> >> > > >> >> >> >You mean does it break existing FSBL flow? if yes add
> >> > > >> >> >> >proper commit message, but I am able to boot SPL MMC w/o
> >this?
> >> > > >> >> >>
> >> > > >> >> >> Cache ways are enabled by FSBL also and if I will send
> >> > > >> >> >> cache ways patches separately then it will a duplicate
> >> > > >> >> >> way of enabling cache ways if
> >> > > >> >> >someone using FSBL.
> >> > > >> >> >
> >> > > >> >> >Sorry I didn't get you.
> >> > > >> >> >
> >> > > >> >> >If we cannot include these changes does U-Boot SPL break existing
> >FSBL?
> >> > > >> >>
> >> > > >> >> No, U-Boot SPL does not break without this.
> >> > > >> >>
> >> > > >> >> As of now, we also want to support FSBL flow and FSBL also
> >> > > >> >> enabled the Cache ways for U-Boot proper and if someone use
> >> > > >> >> this patches of
> >> > > >> >> L2 cache enable ways will FSBL then it will be a duplicate
> >> > > >> >> work of cache enable
> >> > > >> >ways.
> >> > > >> >
> >> > > >> >My question is what if we don't add this change at all?
> >> > > >>
> >> > > >> U-Boot SPL will work without L2 cache enable patches but why we
> >> > > >> want to
> >> > > >do this.
> >> > > >> This series is not just for SPL mmc booting but also replacing
> >> > > >> FSBL functionality so better to cover all FSBL stuff in one series.
> >> > > >
> >> > > >So, FSBL flow would break if we add U-Boot SPL so this patch
> >> > > >fixing by enabling cache's explicitly to avoid that break. isn't it?
> >> > >
> >> > > No, you are not getting this.
> >> > >
> >> > > Initially FSBL enable the cache ways before U-Boot SPL.
> >> > > https://github.com/sifive/freedom-u540-c000-bootloader/blob/master
> >> > > /fsbl/main.c#L428
> >> >
> >> > This is not Mainline. enabling cache's are a new thing for Mainline
> >> > for you. So this code is pretty much new. Is that clear?
> >> >
> >> > >
> >> > > Now U-Boot SPL doing the same in [v7 19/22] and [v7 20/22].
> >> >
> >> > But these two patches enable caches for U-Boot proper in case of
> >> > U-Boot SPL flow and U-Boot in case of FSBL. am I correct? if so this
> >> > code is purely U-Boot specific neither FSBL nor U-Boot SPL. then
> >> > what is the problem of having a series or separate patches with
> >> > cache enablement.
> >>
> >> My understanding is that:
> >>
> >> 1. This patch series is adding SiFive FU540 U-Boot SPL support 2. The
> >> purpose is to replace SiFive provided FSBL with U-Boot SPL 3. SiFive
> >> FSBL initializes L2 cache before loading next stage payload 4. U-Boot
> >> SPL should provide the same features, like initializing L2 cache
> >
> >So, you mean U-Boot SPL would enable the cache similar like FSBL does right?
> >but this patch [1] enabling cache only for U-Boot not SPL isn't it?
> >
> >[1]
> >https://patchwork.ozlabs.org/project/uboot/patch/20200502100628.24809-
> >20-pragnesh.patel at sifive.com/
>
> Yes, you are right. Cache ways are enabled by U-Boot proper not by U-Boot SPL.
> Will pull cache related patches out of this series and send as separate patches.
>
Now I am confused. Are you saying that FSBL does NOT enable L2 cache?
Based on your statement in this review thread I think you basically
wanted to replace FSBL with the same featured U-Boot SPL.
Regards,
Bin
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
2020-05-11 9:47 ` Bin Meng
@ 2020-05-11 9:55 ` Pragnesh Patel
2020-05-11 10:10 ` Bin Meng
2020-05-12 7:45 ` Jagan Teki
0 siblings, 2 replies; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-11 9:55 UTC (permalink / raw)
To: u-boot
>-----Original Message-----
>From: Bin Meng <bmeng.cn@gmail.com>
>Sent: 11 May 2020 15:17
>To: Pragnesh Patel <pragnesh.patel@sifive.com>
>Cc: Jagan Teki <jagan@amarulasolutions.com>; U-Boot-Denx <u-
>boot at lists.denx.de>; Atish Patra <atish.patra@wdc.com>; Palmer Dabbelt
><palmerdabbelt@google.com>; Paul Walmsley <paul.walmsley@sifive.com>;
>Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
><rick@andestech.com>
>Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
>
>[External Email] Do not click links or attachments unless you recognize the
>sender and know the content is safe
>
>Hi Pragnesh,
>
>On Mon, May 11, 2020 at 5:34 PM Pragnesh Patel
><pragnesh.patel@sifive.com> wrote:
>>
>> >-----Original Message-----
>> >From: Jagan Teki <jagan@amarulasolutions.com>
>> >Sent: 11 May 2020 14:35
>> >To: Bin Meng <bmeng.cn@gmail.com>
>> >Cc: Pragnesh Patel <pragnesh.patel@sifive.com>; U-Boot-Denx <u-
>> >boot at lists.denx.de>; Atish Patra <atish.patra@wdc.com>; Palmer
>> >Dabbelt <palmerdabbelt@google.com>; Paul Walmsley
>> ><paul.walmsley@sifive.com>; Troy Benjegerdes
>> ><troy.benjegerdes@sifive.com>; Anup Patel <anup.patel@wdc.com>; Sagar
>> >Kadam <sagar.kadam@sifive.com>; Rick Chen <rick@andestech.com>
>> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in
>> >U-Boot
>> >
>> >[External Email] Do not click links or attachments unless you
>> >recognize the sender and know the content is safe
>> >
>> >Hi Bin,
>> >
>> >On Mon, May 11, 2020 at 2:30 PM Bin Meng <bmeng.cn@gmail.com>
>wrote:
>> >>
>> >> Hi Jagan,
>> >>
>> >> On Mon, May 11, 2020 at 4:48 PM Jagan Teki
>> ><jagan@amarulasolutions.com> wrote:
>> >> >
>> >> > On Mon, May 11, 2020 at 1:15 PM Pragnesh Patel
>> >> > <pragnesh.patel@sifive.com> wrote:
>> >> > >
>> >> > > >-----Original Message-----
>> >> > > >From: Jagan Teki <jagan@amarulasolutions.com>
>> >> > > >Sent: 11 May 2020 12:56
>> >> > > >To: Pragnesh Patel <pragnesh.patel@sifive.com>
>> >> > > >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
>> >> > > ><atish.patra@wdc.com>; Palmer Dabbelt
>> ><palmerdabbelt@google.com>;
>> >> > > >Bin Meng <bmeng.cn@gmail.com>; Paul Walmsley
>> >> > > ><paul.walmsley@sifive.com>; Troy Benjegerdes
>> >> > > ><troy.benjegerdes@sifive.com>; Anup Patel
>> >> > > ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>;
>> >> > > >Rick Chen <rick@andestech.com>
>> >> > > >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2
>> >> > > >Cache in U-Boot
>> >> > > >
>> >> > > >[External Email] Do not click links or attachments unless you
>> >> > > >recognize the sender and know the content is safe
>> >> > > >
>> >> > > >On Mon, May 11, 2020 at 12:37 PM Pragnesh Patel
>> >> > > ><pragnesh.patel@sifive.com> wrote:
>> >> > > >>
>> >> > > >> >-----Original Message-----
>> >> > > >> >From: Jagan Teki <jagan@amarulasolutions.com>
>> >> > > >> >Sent: 11 May 2020 12:25
>> >> > > >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
>> >> > > >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
>> >> > > >> ><atish.patra@wdc.com>; Palmer Dabbelt
>> >> > > >> ><palmerdabbelt@google.com>;
>> >> > > >Bin
>> >> > > >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
>> >> > > ><paul.walmsley@sifive.com>;
>> >> > > >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
>> >> > > >> ><anup.patel@wdc.com>; Sagar Kadam
><sagar.kadam@sifive.com>;
>> >> > > >> >Rick
>> >> > > >Chen
>> >> > > >> ><rick@andestech.com>
>> >> > > >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2
>> >> > > >> >Cache in U-Boot
>> >> > > >> >
>> >> > > >> >[External Email] Do not click links or attachments unless
>> >> > > >> >you recognize the sender and know the content is safe
>> >> > > >> >
>> >> > > >> >On Mon, May 11, 2020 at 11:35 AM Pragnesh Patel
>> >> > > >> ><pragnesh.patel@sifive.com> wrote:
>> >> > > >> >>
>> >> > > >> >> >-----Original Message-----
>> >> > > >> >> >From: Jagan Teki <jagan@amarulasolutions.com>
>> >> > > >> >> >Sent: 10 May 2020 15:02
>> >> > > >> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
>> >> > > >> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
>> >> > > >> >> ><atish.patra@wdc.com>; Palmer Dabbelt
>> >> > > ><palmerdabbelt@google.com>;
>> >> > > >> >Bin
>> >> > > >> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
>> >> > > >> ><paul.walmsley@sifive.com>;
>> >> > > >> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup
>> >> > > >> >> >Patel <anup.patel@wdc.com>; Sagar Kadam
>> ><sagar.kadam@sifive.com>;
>> >> > > >> >> >Rick
>> >> > > >> >Chen
>> >> > > >> >> ><rick@andestech.com>
>> >> > > >> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable
>> >> > > >> >> >L2 Cache in U-Boot
>> >> > > >> >> >
>> >> > > >> >> >[External Email] Do not click links or attachments
>> >> > > >> >> >unless you recognize the sender and know the content is
>> >> > > >> >> >safe
>> >> > > >> >> >
>> >> > > >> >> >On Sun, May 3, 2020 at 12:57 PM Pragnesh Patel
>> >> > > >> >> ><pragnesh.patel@sifive.com> wrote:
>> >> > > >> >> >>
>> >> > > >> >> >> Hi jagan,
>> >> > > >> >> >>
>> >> > > >> >> >> >-----Original Message-----
>> >> > > >> >> >> >From: Jagan Teki <jagan@amarulasolutions.com>
>> >> > > >> >> >> >Sent: 02 May 2020 22:43
>> >> > > >> >> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
>> >> > > >> >> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
>> >> > > >> >> >> ><atish.patra@wdc.com>; Palmer Dabbelt
>> >> > > >> ><palmerdabbelt@google.com>;
>> >> > > >> >> >Bin
>> >> > > >> >> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
>> >> > > >> >> ><paul.walmsley@sifive.com>;
>> >> > > >> >> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup
>> >> > > >> >> >> >Patel <anup.patel@wdc.com>; Sagar Kadam
>> >> > > >> >> >> ><sagar.kadam@sifive.com>; Rick
>> >> > > >> >> >Chen
>> >> > > >> >> >> ><rick@andestech.com>
>> >> > > >> >> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540:
>> >> > > >> >> >> >Enable
>> >> > > >> >> >> >L2 Cache in U-Boot
>> >> > > >> >> >> >
>> >> > > >> >> >> >[External Email] Do not click links or attachments
>> >> > > >> >> >> >unless you recognize the sender and know the content
>> >> > > >> >> >> >is safe
>> >> > > >> >> >> >
>> >> > > >> >> >> >On Sat, May 2, 2020 at 10:12 PM Pragnesh Patel
>> >> > > >> >> >> ><pragnesh.patel@sifive.com>
>> >> > > >> >> >> >wrote:
>> >> > > >> >> >> >>
>> >> > > >> >> >> >> Hi Jagan,
>> >> > > >> >> >> >>
>> >> > > >> >> >> >> >-----Original Message-----
>> >> > > >> >> >> >> >From: Jagan Teki <jagan@amarulasolutions.com>
>> >> > > >> >> >> >> >Sent: 02 May 2020 21:49
>> >> > > >> >> >> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
>> >> > > >> >> >> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish
>> >> > > >> >> >> >> >Patra <atish.patra@wdc.com>; Palmer Dabbelt
>> >> > > >> >> ><palmerdabbelt@google.com>;
>> >> > > >> >> >> >Bin
>> >> > > >> >> >> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
>> >> > > >> >> >> ><paul.walmsley@sifive.com>;
>> >> > > >> >> >> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>;
>> >> > > >> >> >> >> >Anup Patel <anup.patel@wdc.com>; Sagar Kadam
>> >> > > ><sagar.kadam@sifive.com>;
>> >> > > >> >> >> >> >Rick
>> >> > > >> >> >> >Chen
>> >> > > >> >> >> >> ><rick@andestech.com>
>> >> > > >> >> >> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540:
>> >> > > >> >> >> >> >Enable L2 Cache in U-Boot
>> >> > > >> >> >> >> >
>> >> > > >> >> >> >> >[External Email] Do not click links or attachments
>> >> > > >> >> >> >> >unless you recognize the sender and know the
>> >> > > >> >> >> >> >content is safe
>> >> > > >> >> >> >> >
>> >> > > >> >> >> >> >On Sat, May 2, 2020 at 3:39 PM Pragnesh Patel
>> >> > > >> >> >> >> ><pragnesh.patel@sifive.com>
>> >> > > >> >> >> >> >wrote:
>> >> > > >> >> >> >> >>
>> >> > > >> >> >> >> >> Add L2 cache node to enable cache ways from
>> >> > > >> >> >> >> >> U-Boot
>> >> > > >> >> >> >> >
>> >> > > >> >> >> >> >This and 20/22 doesn't relate to SPL MMC boot?, if
>> >> > > >> >> >> >> >yes please send them separately.
>> >> > > >> >> >> >>
>> >> > > >> >> >> >> This series is for replacing FSBL and all the
>> >> > > >> >> >> >> patches are related to
>> >> > > >that.
>> >> > > >> >> >> >> IMHO it's better to add all FSBL functionality in one series.
>> >> > > >> >> >> >
>> >> > > >> >> >> >You mean does it break existing FSBL flow? if yes add
>> >> > > >> >> >> >proper commit message, but I am able to boot SPL MMC
>> >> > > >> >> >> >w/o
>> >this?
>> >> > > >> >> >>
>> >> > > >> >> >> Cache ways are enabled by FSBL also and if I will send
>> >> > > >> >> >> cache ways patches separately then it will a duplicate
>> >> > > >> >> >> way of enabling cache ways if
>> >> > > >> >> >someone using FSBL.
>> >> > > >> >> >
>> >> > > >> >> >Sorry I didn't get you.
>> >> > > >> >> >
>> >> > > >> >> >If we cannot include these changes does U-Boot SPL break
>> >> > > >> >> >existing
>> >FSBL?
>> >> > > >> >>
>> >> > > >> >> No, U-Boot SPL does not break without this.
>> >> > > >> >>
>> >> > > >> >> As of now, we also want to support FSBL flow and FSBL
>> >> > > >> >> also enabled the Cache ways for U-Boot proper and if
>> >> > > >> >> someone use this patches of
>> >> > > >> >> L2 cache enable ways will FSBL then it will be a
>> >> > > >> >> duplicate work of cache enable
>> >> > > >> >ways.
>> >> > > >> >
>> >> > > >> >My question is what if we don't add this change at all?
>> >> > > >>
>> >> > > >> U-Boot SPL will work without L2 cache enable patches but why
>> >> > > >> we want to
>> >> > > >do this.
>> >> > > >> This series is not just for SPL mmc booting but also
>> >> > > >> replacing FSBL functionality so better to cover all FSBL stuff in one
>series.
>> >> > > >
>> >> > > >So, FSBL flow would break if we add U-Boot SPL so this patch
>> >> > > >fixing by enabling cache's explicitly to avoid that break. isn't it?
>> >> > >
>> >> > > No, you are not getting this.
>> >> > >
>> >> > > Initially FSBL enable the cache ways before U-Boot SPL.
>> >> > > https://github.com/sifive/freedom-u540-c000-bootloader/blob/mas
>> >> > > ter
>> >> > > /fsbl/main.c#L428
>> >> >
>> >> > This is not Mainline. enabling cache's are a new thing for
>> >> > Mainline for you. So this code is pretty much new. Is that clear?
>> >> >
>> >> > >
>> >> > > Now U-Boot SPL doing the same in [v7 19/22] and [v7 20/22].
>> >> >
>> >> > But these two patches enable caches for U-Boot proper in case of
>> >> > U-Boot SPL flow and U-Boot in case of FSBL. am I correct? if so
>> >> > this code is purely U-Boot specific neither FSBL nor U-Boot SPL.
>> >> > then what is the problem of having a series or separate patches
>> >> > with cache enablement.
>> >>
>> >> My understanding is that:
>> >>
>> >> 1. This patch series is adding SiFive FU540 U-Boot SPL support 2.
>> >> The purpose is to replace SiFive provided FSBL with U-Boot SPL 3.
>> >> SiFive FSBL initializes L2 cache before loading next stage payload
>> >> 4. U-Boot SPL should provide the same features, like initializing
>> >> L2 cache
>> >
>> >So, you mean U-Boot SPL would enable the cache similar like FSBL does
>right?
>> >but this patch [1] enabling cache only for U-Boot not SPL isn't it?
>> >
>> >[1]
>>
>>https://patchwork.ozlabs.org/project/uboot/patch/20200502100628.24809
>> >-
>> >20-pragnesh.patel at sifive.com/
>>
>> Yes, you are right. Cache ways are enabled by U-Boot proper not by U-Boot
>SPL.
>> Will pull cache related patches out of this series and send as separate
>patches.
>>
>
>Now I am confused. Are you saying that FSBL does NOT enable L2 cache?
>Based on your statement in this review thread I think you basically wanted to
>replace FSBL with the same featured U-Boot SPL.
For FSBL flow,
Cache ways are enabled by FSBL and with this series cache ways are again enabled by U-Boot
Proper. Once this series has been merged, we may remove cache enable ways from FSBL or I
Will apply check in U-Boot proper for already enabled cache ways.
For SPL flow,
Cache ways are enabled by U-Boot proper. We can not enable cache ways from U-Boot SPL because
SPL is running from L2 LIM.
@Jagan Teki Sorry for my misunderstanding, U-Boot SPL got stuck in my mind.
>
>Regards,
>Bin
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
2020-05-11 9:55 ` Pragnesh Patel
@ 2020-05-11 10:10 ` Bin Meng
2020-05-11 10:35 ` Pragnesh Patel
2020-05-12 7:45 ` Jagan Teki
1 sibling, 1 reply; 118+ messages in thread
From: Bin Meng @ 2020-05-11 10:10 UTC (permalink / raw)
To: u-boot
Hi Pragnesh,
On Mon, May 11, 2020 at 5:55 PM Pragnesh Patel
<pragnesh.patel@sifive.com> wrote:
>
> >-----Original Message-----
> >From: Bin Meng <bmeng.cn@gmail.com>
> >Sent: 11 May 2020 15:17
> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >Cc: Jagan Teki <jagan@amarulasolutions.com>; U-Boot-Denx <u-
> >boot at lists.denx.de>; Atish Patra <atish.patra@wdc.com>; Palmer Dabbelt
> ><palmerdabbelt@google.com>; Paul Walmsley <paul.walmsley@sifive.com>;
> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
> ><rick@andestech.com>
> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
> >
> >[External Email] Do not click links or attachments unless you recognize the
> >sender and know the content is safe
> >
> >Hi Pragnesh,
> >
> >On Mon, May 11, 2020 at 5:34 PM Pragnesh Patel
> ><pragnesh.patel@sifive.com> wrote:
> >>
> >> >-----Original Message-----
> >> >From: Jagan Teki <jagan@amarulasolutions.com>
> >> >Sent: 11 May 2020 14:35
> >> >To: Bin Meng <bmeng.cn@gmail.com>
> >> >Cc: Pragnesh Patel <pragnesh.patel@sifive.com>; U-Boot-Denx <u-
> >> >boot at lists.denx.de>; Atish Patra <atish.patra@wdc.com>; Palmer
> >> >Dabbelt <palmerdabbelt@google.com>; Paul Walmsley
> >> ><paul.walmsley@sifive.com>; Troy Benjegerdes
> >> ><troy.benjegerdes@sifive.com>; Anup Patel <anup.patel@wdc.com>; Sagar
> >> >Kadam <sagar.kadam@sifive.com>; Rick Chen <rick@andestech.com>
> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in
> >> >U-Boot
> >> >
> >> >[External Email] Do not click links or attachments unless you
> >> >recognize the sender and know the content is safe
> >> >
> >> >Hi Bin,
> >> >
> >> >On Mon, May 11, 2020 at 2:30 PM Bin Meng <bmeng.cn@gmail.com>
> >wrote:
> >> >>
> >> >> Hi Jagan,
> >> >>
> >> >> On Mon, May 11, 2020 at 4:48 PM Jagan Teki
> >> ><jagan@amarulasolutions.com> wrote:
> >> >> >
> >> >> > On Mon, May 11, 2020 at 1:15 PM Pragnesh Patel
> >> >> > <pragnesh.patel@sifive.com> wrote:
> >> >> > >
> >> >> > > >-----Original Message-----
> >> >> > > >From: Jagan Teki <jagan@amarulasolutions.com>
> >> >> > > >Sent: 11 May 2020 12:56
> >> >> > > >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> >> > > >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> >> >> > > ><atish.patra@wdc.com>; Palmer Dabbelt
> >> ><palmerdabbelt@google.com>;
> >> >> > > >Bin Meng <bmeng.cn@gmail.com>; Paul Walmsley
> >> >> > > ><paul.walmsley@sifive.com>; Troy Benjegerdes
> >> >> > > ><troy.benjegerdes@sifive.com>; Anup Patel
> >> >> > > ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>;
> >> >> > > >Rick Chen <rick@andestech.com>
> >> >> > > >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2
> >> >> > > >Cache in U-Boot
> >> >> > > >
> >> >> > > >[External Email] Do not click links or attachments unless you
> >> >> > > >recognize the sender and know the content is safe
> >> >> > > >
> >> >> > > >On Mon, May 11, 2020 at 12:37 PM Pragnesh Patel
> >> >> > > ><pragnesh.patel@sifive.com> wrote:
> >> >> > > >>
> >> >> > > >> >-----Original Message-----
> >> >> > > >> >From: Jagan Teki <jagan@amarulasolutions.com>
> >> >> > > >> >Sent: 11 May 2020 12:25
> >> >> > > >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> >> > > >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> >> >> > > >> ><atish.patra@wdc.com>; Palmer Dabbelt
> >> >> > > >> ><palmerdabbelt@google.com>;
> >> >> > > >Bin
> >> >> > > >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
> >> >> > > ><paul.walmsley@sifive.com>;
> >> >> > > >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> >> >> > > >> ><anup.patel@wdc.com>; Sagar Kadam
> ><sagar.kadam@sifive.com>;
> >> >> > > >> >Rick
> >> >> > > >Chen
> >> >> > > >> ><rick@andestech.com>
> >> >> > > >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2
> >> >> > > >> >Cache in U-Boot
> >> >> > > >> >
> >> >> > > >> >[External Email] Do not click links or attachments unless
> >> >> > > >> >you recognize the sender and know the content is safe
> >> >> > > >> >
> >> >> > > >> >On Mon, May 11, 2020 at 11:35 AM Pragnesh Patel
> >> >> > > >> ><pragnesh.patel@sifive.com> wrote:
> >> >> > > >> >>
> >> >> > > >> >> >-----Original Message-----
> >> >> > > >> >> >From: Jagan Teki <jagan@amarulasolutions.com>
> >> >> > > >> >> >Sent: 10 May 2020 15:02
> >> >> > > >> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> >> > > >> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> >> >> > > >> >> ><atish.patra@wdc.com>; Palmer Dabbelt
> >> >> > > ><palmerdabbelt@google.com>;
> >> >> > > >> >Bin
> >> >> > > >> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
> >> >> > > >> ><paul.walmsley@sifive.com>;
> >> >> > > >> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup
> >> >> > > >> >> >Patel <anup.patel@wdc.com>; Sagar Kadam
> >> ><sagar.kadam@sifive.com>;
> >> >> > > >> >> >Rick
> >> >> > > >> >Chen
> >> >> > > >> >> ><rick@andestech.com>
> >> >> > > >> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable
> >> >> > > >> >> >L2 Cache in U-Boot
> >> >> > > >> >> >
> >> >> > > >> >> >[External Email] Do not click links or attachments
> >> >> > > >> >> >unless you recognize the sender and know the content is
> >> >> > > >> >> >safe
> >> >> > > >> >> >
> >> >> > > >> >> >On Sun, May 3, 2020 at 12:57 PM Pragnesh Patel
> >> >> > > >> >> ><pragnesh.patel@sifive.com> wrote:
> >> >> > > >> >> >>
> >> >> > > >> >> >> Hi jagan,
> >> >> > > >> >> >>
> >> >> > > >> >> >> >-----Original Message-----
> >> >> > > >> >> >> >From: Jagan Teki <jagan@amarulasolutions.com>
> >> >> > > >> >> >> >Sent: 02 May 2020 22:43
> >> >> > > >> >> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> >> > > >> >> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> >> >> > > >> >> >> ><atish.patra@wdc.com>; Palmer Dabbelt
> >> >> > > >> ><palmerdabbelt@google.com>;
> >> >> > > >> >> >Bin
> >> >> > > >> >> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
> >> >> > > >> >> ><paul.walmsley@sifive.com>;
> >> >> > > >> >> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup
> >> >> > > >> >> >> >Patel <anup.patel@wdc.com>; Sagar Kadam
> >> >> > > >> >> >> ><sagar.kadam@sifive.com>; Rick
> >> >> > > >> >> >Chen
> >> >> > > >> >> >> ><rick@andestech.com>
> >> >> > > >> >> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540:
> >> >> > > >> >> >> >Enable
> >> >> > > >> >> >> >L2 Cache in U-Boot
> >> >> > > >> >> >> >
> >> >> > > >> >> >> >[External Email] Do not click links or attachments
> >> >> > > >> >> >> >unless you recognize the sender and know the content
> >> >> > > >> >> >> >is safe
> >> >> > > >> >> >> >
> >> >> > > >> >> >> >On Sat, May 2, 2020 at 10:12 PM Pragnesh Patel
> >> >> > > >> >> >> ><pragnesh.patel@sifive.com>
> >> >> > > >> >> >> >wrote:
> >> >> > > >> >> >> >>
> >> >> > > >> >> >> >> Hi Jagan,
> >> >> > > >> >> >> >>
> >> >> > > >> >> >> >> >-----Original Message-----
> >> >> > > >> >> >> >> >From: Jagan Teki <jagan@amarulasolutions.com>
> >> >> > > >> >> >> >> >Sent: 02 May 2020 21:49
> >> >> > > >> >> >> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> >> > > >> >> >> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish
> >> >> > > >> >> >> >> >Patra <atish.patra@wdc.com>; Palmer Dabbelt
> >> >> > > >> >> ><palmerdabbelt@google.com>;
> >> >> > > >> >> >> >Bin
> >> >> > > >> >> >> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
> >> >> > > >> >> >> ><paul.walmsley@sifive.com>;
> >> >> > > >> >> >> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>;
> >> >> > > >> >> >> >> >Anup Patel <anup.patel@wdc.com>; Sagar Kadam
> >> >> > > ><sagar.kadam@sifive.com>;
> >> >> > > >> >> >> >> >Rick
> >> >> > > >> >> >> >Chen
> >> >> > > >> >> >> >> ><rick@andestech.com>
> >> >> > > >> >> >> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540:
> >> >> > > >> >> >> >> >Enable L2 Cache in U-Boot
> >> >> > > >> >> >> >> >
> >> >> > > >> >> >> >> >[External Email] Do not click links or attachments
> >> >> > > >> >> >> >> >unless you recognize the sender and know the
> >> >> > > >> >> >> >> >content is safe
> >> >> > > >> >> >> >> >
> >> >> > > >> >> >> >> >On Sat, May 2, 2020 at 3:39 PM Pragnesh Patel
> >> >> > > >> >> >> >> ><pragnesh.patel@sifive.com>
> >> >> > > >> >> >> >> >wrote:
> >> >> > > >> >> >> >> >>
> >> >> > > >> >> >> >> >> Add L2 cache node to enable cache ways from
> >> >> > > >> >> >> >> >> U-Boot
> >> >> > > >> >> >> >> >
> >> >> > > >> >> >> >> >This and 20/22 doesn't relate to SPL MMC boot?, if
> >> >> > > >> >> >> >> >yes please send them separately.
> >> >> > > >> >> >> >>
> >> >> > > >> >> >> >> This series is for replacing FSBL and all the
> >> >> > > >> >> >> >> patches are related to
> >> >> > > >that.
> >> >> > > >> >> >> >> IMHO it's better to add all FSBL functionality in one series.
> >> >> > > >> >> >> >
> >> >> > > >> >> >> >You mean does it break existing FSBL flow? if yes add
> >> >> > > >> >> >> >proper commit message, but I am able to boot SPL MMC
> >> >> > > >> >> >> >w/o
> >> >this?
> >> >> > > >> >> >>
> >> >> > > >> >> >> Cache ways are enabled by FSBL also and if I will send
> >> >> > > >> >> >> cache ways patches separately then it will a duplicate
> >> >> > > >> >> >> way of enabling cache ways if
> >> >> > > >> >> >someone using FSBL.
> >> >> > > >> >> >
> >> >> > > >> >> >Sorry I didn't get you.
> >> >> > > >> >> >
> >> >> > > >> >> >If we cannot include these changes does U-Boot SPL break
> >> >> > > >> >> >existing
> >> >FSBL?
> >> >> > > >> >>
> >> >> > > >> >> No, U-Boot SPL does not break without this.
> >> >> > > >> >>
> >> >> > > >> >> As of now, we also want to support FSBL flow and FSBL
> >> >> > > >> >> also enabled the Cache ways for U-Boot proper and if
> >> >> > > >> >> someone use this patches of
> >> >> > > >> >> L2 cache enable ways will FSBL then it will be a
> >> >> > > >> >> duplicate work of cache enable
> >> >> > > >> >ways.
> >> >> > > >> >
> >> >> > > >> >My question is what if we don't add this change at all?
> >> >> > > >>
> >> >> > > >> U-Boot SPL will work without L2 cache enable patches but why
> >> >> > > >> we want to
> >> >> > > >do this.
> >> >> > > >> This series is not just for SPL mmc booting but also
> >> >> > > >> replacing FSBL functionality so better to cover all FSBL stuff in one
> >series.
> >> >> > > >
> >> >> > > >So, FSBL flow would break if we add U-Boot SPL so this patch
> >> >> > > >fixing by enabling cache's explicitly to avoid that break. isn't it?
> >> >> > >
> >> >> > > No, you are not getting this.
> >> >> > >
> >> >> > > Initially FSBL enable the cache ways before U-Boot SPL.
> >> >> > > https://github.com/sifive/freedom-u540-c000-bootloader/blob/mas
> >> >> > > ter
> >> >> > > /fsbl/main.c#L428
> >> >> >
> >> >> > This is not Mainline. enabling cache's are a new thing for
> >> >> > Mainline for you. So this code is pretty much new. Is that clear?
> >> >> >
> >> >> > >
> >> >> > > Now U-Boot SPL doing the same in [v7 19/22] and [v7 20/22].
> >> >> >
> >> >> > But these two patches enable caches for U-Boot proper in case of
> >> >> > U-Boot SPL flow and U-Boot in case of FSBL. am I correct? if so
> >> >> > this code is purely U-Boot specific neither FSBL nor U-Boot SPL.
> >> >> > then what is the problem of having a series or separate patches
> >> >> > with cache enablement.
> >> >>
> >> >> My understanding is that:
> >> >>
> >> >> 1. This patch series is adding SiFive FU540 U-Boot SPL support 2.
> >> >> The purpose is to replace SiFive provided FSBL with U-Boot SPL 3.
> >> >> SiFive FSBL initializes L2 cache before loading next stage payload
> >> >> 4. U-Boot SPL should provide the same features, like initializing
> >> >> L2 cache
> >> >
> >> >So, you mean U-Boot SPL would enable the cache similar like FSBL does
> >right?
> >> >but this patch [1] enabling cache only for U-Boot not SPL isn't it?
> >> >
> >> >[1]
> >>
> >>https://patchwork.ozlabs.org/project/uboot/patch/20200502100628.24809
> >> >-
> >> >20-pragnesh.patel at sifive.com/
> >>
> >> Yes, you are right. Cache ways are enabled by U-Boot proper not by U-Boot
> >SPL.
> >> Will pull cache related patches out of this series and send as separate
> >patches.
> >>
> >
> >Now I am confused. Are you saying that FSBL does NOT enable L2 cache?
> >Based on your statement in this review thread I think you basically wanted to
> >replace FSBL with the same featured U-Boot SPL.
>
> For FSBL flow,
> Cache ways are enabled by FSBL and with this series cache ways are again enabled by U-Boot
> Proper. Once this series has been merged, we may remove cache enable ways from FSBL or I
> Will apply check in U-Boot proper for already enabled cache ways.
>
> For SPL flow,
> Cache ways are enabled by U-Boot proper. We can not enable cache ways from U-Boot SPL because
> SPL is running from L2 LIM.
>
Thanks for the clarification. I wonder where is the FSBL running. Can
U-Boot SPL run from where FSBL is running instead of L2 LIM?
> @Jagan Teki Sorry for my misunderstanding, U-Boot SPL got stuck in my mind.
>
Regards,
Bin
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
2020-05-11 10:10 ` Bin Meng
@ 2020-05-11 10:35 ` Pragnesh Patel
2020-05-12 1:20 ` Bin Meng
0 siblings, 1 reply; 118+ messages in thread
From: Pragnesh Patel @ 2020-05-11 10:35 UTC (permalink / raw)
To: u-boot
>-----Original Message-----
>From: Bin Meng <bmeng.cn@gmail.com>
>Sent: 11 May 2020 15:41
>To: Pragnesh Patel <pragnesh.patel@sifive.com>
>Cc: Jagan Teki <jagan@amarulasolutions.com>; U-Boot-Denx <u-
>boot at lists.denx.de>; Atish Patra <atish.patra@wdc.com>; Palmer Dabbelt
><palmerdabbelt@google.com>; Paul Walmsley <paul.walmsley@sifive.com>;
>Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
><rick@andestech.com>
>Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
>
>[External Email] Do not click links or attachments unless you recognize the
>sender and know the content is safe
>
>Hi Pragnesh,
>
>On Mon, May 11, 2020 at 5:55 PM Pragnesh Patel
><pragnesh.patel@sifive.com> wrote:
>>
>> >-----Original Message-----
>> >From: Bin Meng <bmeng.cn@gmail.com>
>> >Sent: 11 May 2020 15:17
>> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
>> >Cc: Jagan Teki <jagan@amarulasolutions.com>; U-Boot-Denx <u-
>> >boot at lists.denx.de>; Atish Patra <atish.patra@wdc.com>; Palmer
>> >Dabbelt <palmerdabbelt@google.com>; Paul Walmsley
>> ><paul.walmsley@sifive.com>; Troy Benjegerdes
>> ><troy.benjegerdes@sifive.com>; Anup Patel <anup.patel@wdc.com>; Sagar
>> >Kadam <sagar.kadam@sifive.com>; Rick Chen <rick@andestech.com>
>> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in
>> >U-Boot
>> >
>> >[External Email] Do not click links or attachments unless you
>> >recognize the sender and know the content is safe
>> >
>> >Hi Pragnesh,
>> >
>> >On Mon, May 11, 2020 at 5:34 PM Pragnesh Patel
>> ><pragnesh.patel@sifive.com> wrote:
>> >>
>> >> >-----Original Message-----
>> >> >From: Jagan Teki <jagan@amarulasolutions.com>
>> >> >Sent: 11 May 2020 14:35
>> >> >To: Bin Meng <bmeng.cn@gmail.com>
>> >> >Cc: Pragnesh Patel <pragnesh.patel@sifive.com>; U-Boot-Denx <u-
>> >> >boot at lists.denx.de>; Atish Patra <atish.patra@wdc.com>; Palmer
>> >> >Dabbelt <palmerdabbelt@google.com>; Paul Walmsley
>> >> ><paul.walmsley@sifive.com>; Troy Benjegerdes
>> >> ><troy.benjegerdes@sifive.com>; Anup Patel <anup.patel@wdc.com>;
>> >> >Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
>> >> ><rick@andestech.com>
>> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache
>> >> >in U-Boot
>> >> >
>> >> >[External Email] Do not click links or attachments unless you
>> >> >recognize the sender and know the content is safe
>> >> >
>> >> >Hi Bin,
>> >> >
>> >> >On Mon, May 11, 2020 at 2:30 PM Bin Meng <bmeng.cn@gmail.com>
>> >wrote:
>> >> >>
>> >> >> Hi Jagan,
>> >> >>
>> >> >> On Mon, May 11, 2020 at 4:48 PM Jagan Teki
>> >> ><jagan@amarulasolutions.com> wrote:
>> >> >> >
>> >> >> > On Mon, May 11, 2020 at 1:15 PM Pragnesh Patel
>> >> >> > <pragnesh.patel@sifive.com> wrote:
>> >> >> > >
>> >> >> > > >-----Original Message-----
>> >> >> > > >From: Jagan Teki <jagan@amarulasolutions.com>
>> >> >> > > >Sent: 11 May 2020 12:56
>> >> >> > > >To: Pragnesh Patel <pragnesh.patel@sifive.com>
>> >> >> > > >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
>> >> >> > > ><atish.patra@wdc.com>; Palmer Dabbelt
>> >> ><palmerdabbelt@google.com>;
>> >> >> > > >Bin Meng <bmeng.cn@gmail.com>; Paul Walmsley
>> >> >> > > ><paul.walmsley@sifive.com>; Troy Benjegerdes
>> >> >> > > ><troy.benjegerdes@sifive.com>; Anup Patel
>> >> >> > > ><anup.patel@wdc.com>; Sagar Kadam
><sagar.kadam@sifive.com>;
>> >> >> > > >Rick Chen <rick@andestech.com>
>> >> >> > > >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2
>> >> >> > > >Cache in U-Boot
>> >> >> > > >
>> >> >> > > >[External Email] Do not click links or attachments unless
>> >> >> > > >you recognize the sender and know the content is safe
>> >> >> > > >
>> >> >> > > >On Mon, May 11, 2020 at 12:37 PM Pragnesh Patel
>> >> >> > > ><pragnesh.patel@sifive.com> wrote:
>> >> >> > > >>
>> >> >> > > >> >-----Original Message-----
>> >> >> > > >> >From: Jagan Teki <jagan@amarulasolutions.com>
>> >> >> > > >> >Sent: 11 May 2020 12:25
>> >> >> > > >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
>> >> >> > > >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
>> >> >> > > >> ><atish.patra@wdc.com>; Palmer Dabbelt
>> >> >> > > >> ><palmerdabbelt@google.com>;
>> >> >> > > >Bin
>> >> >> > > >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
>> >> >> > > ><paul.walmsley@sifive.com>;
>> >> >> > > >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup
>> >> >> > > >> >Patel <anup.patel@wdc.com>; Sagar Kadam
>> ><sagar.kadam@sifive.com>;
>> >> >> > > >> >Rick
>> >> >> > > >Chen
>> >> >> > > >> ><rick@andestech.com>
>> >> >> > > >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable
>> >> >> > > >> >L2 Cache in U-Boot
>> >> >> > > >> >
>> >> >> > > >> >[External Email] Do not click links or attachments
>> >> >> > > >> >unless you recognize the sender and know the content is
>> >> >> > > >> >safe
>> >> >> > > >> >
>> >> >> > > >> >On Mon, May 11, 2020 at 11:35 AM Pragnesh Patel
>> >> >> > > >> ><pragnesh.patel@sifive.com> wrote:
>> >> >> > > >> >>
>> >> >> > > >> >> >-----Original Message-----
>> >> >> > > >> >> >From: Jagan Teki <jagan@amarulasolutions.com>
>> >> >> > > >> >> >Sent: 10 May 2020 15:02
>> >> >> > > >> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
>> >> >> > > >> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
>> >> >> > > >> >> ><atish.patra@wdc.com>; Palmer Dabbelt
>> >> >> > > ><palmerdabbelt@google.com>;
>> >> >> > > >> >Bin
>> >> >> > > >> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
>> >> >> > > >> ><paul.walmsley@sifive.com>;
>> >> >> > > >> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup
>> >> >> > > >> >> >Patel <anup.patel@wdc.com>; Sagar Kadam
>> >> ><sagar.kadam@sifive.com>;
>> >> >> > > >> >> >Rick
>> >> >> > > >> >Chen
>> >> >> > > >> >> ><rick@andestech.com>
>> >> >> > > >> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540:
>> >> >> > > >> >> >Enable
>> >> >> > > >> >> >L2 Cache in U-Boot
>> >> >> > > >> >> >
>> >> >> > > >> >> >[External Email] Do not click links or attachments
>> >> >> > > >> >> >unless you recognize the sender and know the content
>> >> >> > > >> >> >is safe
>> >> >> > > >> >> >
>> >> >> > > >> >> >On Sun, May 3, 2020 at 12:57 PM Pragnesh Patel
>> >> >> > > >> >> ><pragnesh.patel@sifive.com> wrote:
>> >> >> > > >> >> >>
>> >> >> > > >> >> >> Hi jagan,
>> >> >> > > >> >> >>
>> >> >> > > >> >> >> >-----Original Message-----
>> >> >> > > >> >> >> >From: Jagan Teki <jagan@amarulasolutions.com>
>> >> >> > > >> >> >> >Sent: 02 May 2020 22:43
>> >> >> > > >> >> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
>> >> >> > > >> >> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish
>> >> >> > > >> >> >> >Patra <atish.patra@wdc.com>; Palmer Dabbelt
>> >> >> > > >> ><palmerdabbelt@google.com>;
>> >> >> > > >> >> >Bin
>> >> >> > > >> >> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
>> >> >> > > >> >> ><paul.walmsley@sifive.com>;
>> >> >> > > >> >> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>;
>> >> >> > > >> >> >> >Anup Patel <anup.patel@wdc.com>; Sagar Kadam
>> >> >> > > >> >> >> ><sagar.kadam@sifive.com>; Rick
>> >> >> > > >> >> >Chen
>> >> >> > > >> >> >> ><rick@andestech.com>
>> >> >> > > >> >> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540:
>> >> >> > > >> >> >> >Enable
>> >> >> > > >> >> >> >L2 Cache in U-Boot
>> >> >> > > >> >> >> >
>> >> >> > > >> >> >> >[External Email] Do not click links or attachments
>> >> >> > > >> >> >> >unless you recognize the sender and know the
>> >> >> > > >> >> >> >content is safe
>> >> >> > > >> >> >> >
>> >> >> > > >> >> >> >On Sat, May 2, 2020 at 10:12 PM Pragnesh Patel
>> >> >> > > >> >> >> ><pragnesh.patel@sifive.com>
>> >> >> > > >> >> >> >wrote:
>> >> >> > > >> >> >> >>
>> >> >> > > >> >> >> >> Hi Jagan,
>> >> >> > > >> >> >> >>
>> >> >> > > >> >> >> >> >-----Original Message-----
>> >> >> > > >> >> >> >> >From: Jagan Teki <jagan@amarulasolutions.com>
>> >> >> > > >> >> >> >> >Sent: 02 May 2020 21:49
>> >> >> > > >> >> >> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
>> >> >> > > >> >> >> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish
>> >> >> > > >> >> >> >> >Patra <atish.patra@wdc.com>; Palmer Dabbelt
>> >> >> > > >> >> ><palmerdabbelt@google.com>;
>> >> >> > > >> >> >> >Bin
>> >> >> > > >> >> >> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
>> >> >> > > >> >> >> ><paul.walmsley@sifive.com>;
>> >> >> > > >> >> >> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>;
>> >> >> > > >> >> >> >> >Anup Patel <anup.patel@wdc.com>; Sagar Kadam
>> >> >> > > ><sagar.kadam@sifive.com>;
>> >> >> > > >> >> >> >> >Rick
>> >> >> > > >> >> >> >Chen
>> >> >> > > >> >> >> >> ><rick@andestech.com>
>> >> >> > > >> >> >> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540:
>> >> >> > > >> >> >> >> >Enable L2 Cache in U-Boot
>> >> >> > > >> >> >> >> >
>> >> >> > > >> >> >> >> >[External Email] Do not click links or
>> >> >> > > >> >> >> >> >attachments unless you recognize the sender and
>> >> >> > > >> >> >> >> >know the content is safe
>> >> >> > > >> >> >> >> >
>> >> >> > > >> >> >> >> >On Sat, May 2, 2020 at 3:39 PM Pragnesh Patel
>> >> >> > > >> >> >> >> ><pragnesh.patel@sifive.com>
>> >> >> > > >> >> >> >> >wrote:
>> >> >> > > >> >> >> >> >>
>> >> >> > > >> >> >> >> >> Add L2 cache node to enable cache ways from
>> >> >> > > >> >> >> >> >> U-Boot
>> >> >> > > >> >> >> >> >
>> >> >> > > >> >> >> >> >This and 20/22 doesn't relate to SPL MMC boot?,
>> >> >> > > >> >> >> >> >if yes please send them separately.
>> >> >> > > >> >> >> >>
>> >> >> > > >> >> >> >> This series is for replacing FSBL and all the
>> >> >> > > >> >> >> >> patches are related to
>> >> >> > > >that.
>> >> >> > > >> >> >> >> IMHO it's better to add all FSBL functionality in one
>series.
>> >> >> > > >> >> >> >
>> >> >> > > >> >> >> >You mean does it break existing FSBL flow? if yes
>> >> >> > > >> >> >> >add proper commit message, but I am able to boot
>> >> >> > > >> >> >> >SPL MMC w/o
>> >> >this?
>> >> >> > > >> >> >>
>> >> >> > > >> >> >> Cache ways are enabled by FSBL also and if I will
>> >> >> > > >> >> >> send cache ways patches separately then it will a
>> >> >> > > >> >> >> duplicate way of enabling cache ways if
>> >> >> > > >> >> >someone using FSBL.
>> >> >> > > >> >> >
>> >> >> > > >> >> >Sorry I didn't get you.
>> >> >> > > >> >> >
>> >> >> > > >> >> >If we cannot include these changes does U-Boot SPL
>> >> >> > > >> >> >break existing
>> >> >FSBL?
>> >> >> > > >> >>
>> >> >> > > >> >> No, U-Boot SPL does not break without this.
>> >> >> > > >> >>
>> >> >> > > >> >> As of now, we also want to support FSBL flow and FSBL
>> >> >> > > >> >> also enabled the Cache ways for U-Boot proper and if
>> >> >> > > >> >> someone use this patches of
>> >> >> > > >> >> L2 cache enable ways will FSBL then it will be a
>> >> >> > > >> >> duplicate work of cache enable
>> >> >> > > >> >ways.
>> >> >> > > >> >
>> >> >> > > >> >My question is what if we don't add this change at all?
>> >> >> > > >>
>> >> >> > > >> U-Boot SPL will work without L2 cache enable patches but
>> >> >> > > >> why we want to
>> >> >> > > >do this.
>> >> >> > > >> This series is not just for SPL mmc booting but also
>> >> >> > > >> replacing FSBL functionality so better to cover all FSBL
>> >> >> > > >> stuff in one
>> >series.
>> >> >> > > >
>> >> >> > > >So, FSBL flow would break if we add U-Boot SPL so this
>> >> >> > > >patch fixing by enabling cache's explicitly to avoid that break. isn't
>it?
>> >> >> > >
>> >> >> > > No, you are not getting this.
>> >> >> > >
>> >> >> > > Initially FSBL enable the cache ways before U-Boot SPL.
>> >> >> > > https://github.com/sifive/freedom-u540-c000-bootloader/blob/
>> >> >> > > mas
>> >> >> > > ter
>> >> >> > > /fsbl/main.c#L428
>> >> >> >
>> >> >> > This is not Mainline. enabling cache's are a new thing for
>> >> >> > Mainline for you. So this code is pretty much new. Is that clear?
>> >> >> >
>> >> >> > >
>> >> >> > > Now U-Boot SPL doing the same in [v7 19/22] and [v7 20/22].
>> >> >> >
>> >> >> > But these two patches enable caches for U-Boot proper in case
>> >> >> > of U-Boot SPL flow and U-Boot in case of FSBL. am I correct?
>> >> >> > if so this code is purely U-Boot specific neither FSBL nor U-Boot SPL.
>> >> >> > then what is the problem of having a series or separate
>> >> >> > patches with cache enablement.
>> >> >>
>> >> >> My understanding is that:
>> >> >>
>> >> >> 1. This patch series is adding SiFive FU540 U-Boot SPL support 2.
>> >> >> The purpose is to replace SiFive provided FSBL with U-Boot SPL 3.
>> >> >> SiFive FSBL initializes L2 cache before loading next stage
>> >> >> payload 4. U-Boot SPL should provide the same features, like
>> >> >> initializing
>> >> >> L2 cache
>> >> >
>> >> >So, you mean U-Boot SPL would enable the cache similar like FSBL
>> >> >does
>> >right?
>> >> >but this patch [1] enabling cache only for U-Boot not SPL isn't it?
>> >> >
>> >> >[1]
>> >>
>>
>>>https://patchwork.ozlabs.org/project/uboot/patch/20200502100628.2480
>> >>9
>> >> >-
>> >> >20-pragnesh.patel at sifive.com/
>> >>
>> >> Yes, you are right. Cache ways are enabled by U-Boot proper not by
>> >> U-Boot
>> >SPL.
>> >> Will pull cache related patches out of this series and send as
>> >> separate
>> >patches.
>> >>
>> >
>> >Now I am confused. Are you saying that FSBL does NOT enable L2 cache?
>> >Based on your statement in this review thread I think you basically
>> >wanted to replace FSBL with the same featured U-Boot SPL.
>>
>> For FSBL flow,
>> Cache ways are enabled by FSBL and with this series cache ways are
>> again enabled by U-Boot Proper. Once this series has been merged, we
>> may remove cache enable ways from FSBL or I Will apply check in U-Boot
>proper for already enabled cache ways.
>>
>> For SPL flow,
>> Cache ways are enabled by U-Boot proper. We can not enable cache ways
>> from U-Boot SPL because SPL is running from L2 LIM.
>>
>
>Thanks for the clarification. I wonder where is the FSBL running. Can U-Boot
>SPL run from where FSBL is running instead of L2 LIM?
FSBL and U-Boot SPL running from the same location.
L2 cache is of 2 MB (16 cache ways) and 1 cache way is of 128 KB.
At runtime, FSBL is located on the latest way of L2 cache. Therefore,
FSBL can only enable the first 15 L2 cache ways to avoid corrupt itself.
(Way 0 is enabled by default)
https://github.com/sifive/freedom-u540-c000-bootloader/blob/master/fsbl/main.c#L428
U-Boot SPL is bigger than FSBL so can not fit in 1 cache way, so I decided to enable all cache ways from
U-Boot proper.
>
>> @Jagan Teki Sorry for my misunderstanding, U-Boot SPL got stuck in my
>mind.
>>
>
>Regards,
>Bin
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
2020-05-11 10:35 ` Pragnesh Patel
@ 2020-05-12 1:20 ` Bin Meng
0 siblings, 0 replies; 118+ messages in thread
From: Bin Meng @ 2020-05-12 1:20 UTC (permalink / raw)
To: u-boot
Hi Pragnesh,
On Mon, May 11, 2020 at 6:35 PM Pragnesh Patel
<pragnesh.patel@sifive.com> wrote:
>
> >-----Original Message-----
> >From: Bin Meng <bmeng.cn@gmail.com>
> >Sent: 11 May 2020 15:41
> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >Cc: Jagan Teki <jagan@amarulasolutions.com>; U-Boot-Denx <u-
> >boot at lists.denx.de>; Atish Patra <atish.patra@wdc.com>; Palmer Dabbelt
> ><palmerdabbelt@google.com>; Paul Walmsley <paul.walmsley@sifive.com>;
> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
> ><rick@andestech.com>
> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
> >
> >[External Email] Do not click links or attachments unless you recognize the
> >sender and know the content is safe
> >
> >Hi Pragnesh,
> >
> >On Mon, May 11, 2020 at 5:55 PM Pragnesh Patel
> ><pragnesh.patel@sifive.com> wrote:
> >>
> >> >-----Original Message-----
> >> >From: Bin Meng <bmeng.cn@gmail.com>
> >> >Sent: 11 May 2020 15:17
> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> >Cc: Jagan Teki <jagan@amarulasolutions.com>; U-Boot-Denx <u-
> >> >boot at lists.denx.de>; Atish Patra <atish.patra@wdc.com>; Palmer
> >> >Dabbelt <palmerdabbelt@google.com>; Paul Walmsley
> >> ><paul.walmsley@sifive.com>; Troy Benjegerdes
> >> ><troy.benjegerdes@sifive.com>; Anup Patel <anup.patel@wdc.com>; Sagar
> >> >Kadam <sagar.kadam@sifive.com>; Rick Chen <rick@andestech.com>
> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in
> >> >U-Boot
> >> >
> >> >[External Email] Do not click links or attachments unless you
> >> >recognize the sender and know the content is safe
> >> >
> >> >Hi Pragnesh,
> >> >
> >> >On Mon, May 11, 2020 at 5:34 PM Pragnesh Patel
> >> ><pragnesh.patel@sifive.com> wrote:
> >> >>
> >> >> >-----Original Message-----
> >> >> >From: Jagan Teki <jagan@amarulasolutions.com>
> >> >> >Sent: 11 May 2020 14:35
> >> >> >To: Bin Meng <bmeng.cn@gmail.com>
> >> >> >Cc: Pragnesh Patel <pragnesh.patel@sifive.com>; U-Boot-Denx <u-
> >> >> >boot at lists.denx.de>; Atish Patra <atish.patra@wdc.com>; Palmer
> >> >> >Dabbelt <palmerdabbelt@google.com>; Paul Walmsley
> >> >> ><paul.walmsley@sifive.com>; Troy Benjegerdes
> >> >> ><troy.benjegerdes@sifive.com>; Anup Patel <anup.patel@wdc.com>;
> >> >> >Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
> >> >> ><rick@andestech.com>
> >> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache
> >> >> >in U-Boot
> >> >> >
> >> >> >[External Email] Do not click links or attachments unless you
> >> >> >recognize the sender and know the content is safe
> >> >> >
> >> >> >Hi Bin,
> >> >> >
> >> >> >On Mon, May 11, 2020 at 2:30 PM Bin Meng <bmeng.cn@gmail.com>
> >> >wrote:
> >> >> >>
> >> >> >> Hi Jagan,
> >> >> >>
> >> >> >> On Mon, May 11, 2020 at 4:48 PM Jagan Teki
> >> >> ><jagan@amarulasolutions.com> wrote:
> >> >> >> >
> >> >> >> > On Mon, May 11, 2020 at 1:15 PM Pragnesh Patel
> >> >> >> > <pragnesh.patel@sifive.com> wrote:
> >> >> >> > >
> >> >> >> > > >-----Original Message-----
> >> >> >> > > >From: Jagan Teki <jagan@amarulasolutions.com>
> >> >> >> > > >Sent: 11 May 2020 12:56
> >> >> >> > > >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> >> >> > > >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> >> >> >> > > ><atish.patra@wdc.com>; Palmer Dabbelt
> >> >> ><palmerdabbelt@google.com>;
> >> >> >> > > >Bin Meng <bmeng.cn@gmail.com>; Paul Walmsley
> >> >> >> > > ><paul.walmsley@sifive.com>; Troy Benjegerdes
> >> >> >> > > ><troy.benjegerdes@sifive.com>; Anup Patel
> >> >> >> > > ><anup.patel@wdc.com>; Sagar Kadam
> ><sagar.kadam@sifive.com>;
> >> >> >> > > >Rick Chen <rick@andestech.com>
> >> >> >> > > >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2
> >> >> >> > > >Cache in U-Boot
> >> >> >> > > >
> >> >> >> > > >[External Email] Do not click links or attachments unless
> >> >> >> > > >you recognize the sender and know the content is safe
> >> >> >> > > >
> >> >> >> > > >On Mon, May 11, 2020 at 12:37 PM Pragnesh Patel
> >> >> >> > > ><pragnesh.patel@sifive.com> wrote:
> >> >> >> > > >>
> >> >> >> > > >> >-----Original Message-----
> >> >> >> > > >> >From: Jagan Teki <jagan@amarulasolutions.com>
> >> >> >> > > >> >Sent: 11 May 2020 12:25
> >> >> >> > > >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> >> >> > > >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> >> >> >> > > >> ><atish.patra@wdc.com>; Palmer Dabbelt
> >> >> >> > > >> ><palmerdabbelt@google.com>;
> >> >> >> > > >Bin
> >> >> >> > > >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
> >> >> >> > > ><paul.walmsley@sifive.com>;
> >> >> >> > > >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup
> >> >> >> > > >> >Patel <anup.patel@wdc.com>; Sagar Kadam
> >> ><sagar.kadam@sifive.com>;
> >> >> >> > > >> >Rick
> >> >> >> > > >Chen
> >> >> >> > > >> ><rick@andestech.com>
> >> >> >> > > >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable
> >> >> >> > > >> >L2 Cache in U-Boot
> >> >> >> > > >> >
> >> >> >> > > >> >[External Email] Do not click links or attachments
> >> >> >> > > >> >unless you recognize the sender and know the content is
> >> >> >> > > >> >safe
> >> >> >> > > >> >
> >> >> >> > > >> >On Mon, May 11, 2020 at 11:35 AM Pragnesh Patel
> >> >> >> > > >> ><pragnesh.patel@sifive.com> wrote:
> >> >> >> > > >> >>
> >> >> >> > > >> >> >-----Original Message-----
> >> >> >> > > >> >> >From: Jagan Teki <jagan@amarulasolutions.com>
> >> >> >> > > >> >> >Sent: 10 May 2020 15:02
> >> >> >> > > >> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> >> >> > > >> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> >> >> >> > > >> >> ><atish.patra@wdc.com>; Palmer Dabbelt
> >> >> >> > > ><palmerdabbelt@google.com>;
> >> >> >> > > >> >Bin
> >> >> >> > > >> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
> >> >> >> > > >> ><paul.walmsley@sifive.com>;
> >> >> >> > > >> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup
> >> >> >> > > >> >> >Patel <anup.patel@wdc.com>; Sagar Kadam
> >> >> ><sagar.kadam@sifive.com>;
> >> >> >> > > >> >> >Rick
> >> >> >> > > >> >Chen
> >> >> >> > > >> >> ><rick@andestech.com>
> >> >> >> > > >> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540:
> >> >> >> > > >> >> >Enable
> >> >> >> > > >> >> >L2 Cache in U-Boot
> >> >> >> > > >> >> >
> >> >> >> > > >> >> >[External Email] Do not click links or attachments
> >> >> >> > > >> >> >unless you recognize the sender and know the content
> >> >> >> > > >> >> >is safe
> >> >> >> > > >> >> >
> >> >> >> > > >> >> >On Sun, May 3, 2020 at 12:57 PM Pragnesh Patel
> >> >> >> > > >> >> ><pragnesh.patel@sifive.com> wrote:
> >> >> >> > > >> >> >>
> >> >> >> > > >> >> >> Hi jagan,
> >> >> >> > > >> >> >>
> >> >> >> > > >> >> >> >-----Original Message-----
> >> >> >> > > >> >> >> >From: Jagan Teki <jagan@amarulasolutions.com>
> >> >> >> > > >> >> >> >Sent: 02 May 2020 22:43
> >> >> >> > > >> >> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> >> >> > > >> >> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish
> >> >> >> > > >> >> >> >Patra <atish.patra@wdc.com>; Palmer Dabbelt
> >> >> >> > > >> ><palmerdabbelt@google.com>;
> >> >> >> > > >> >> >Bin
> >> >> >> > > >> >> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
> >> >> >> > > >> >> ><paul.walmsley@sifive.com>;
> >> >> >> > > >> >> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>;
> >> >> >> > > >> >> >> >Anup Patel <anup.patel@wdc.com>; Sagar Kadam
> >> >> >> > > >> >> >> ><sagar.kadam@sifive.com>; Rick
> >> >> >> > > >> >> >Chen
> >> >> >> > > >> >> >> ><rick@andestech.com>
> >> >> >> > > >> >> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540:
> >> >> >> > > >> >> >> >Enable
> >> >> >> > > >> >> >> >L2 Cache in U-Boot
> >> >> >> > > >> >> >> >
> >> >> >> > > >> >> >> >[External Email] Do not click links or attachments
> >> >> >> > > >> >> >> >unless you recognize the sender and know the
> >> >> >> > > >> >> >> >content is safe
> >> >> >> > > >> >> >> >
> >> >> >> > > >> >> >> >On Sat, May 2, 2020 at 10:12 PM Pragnesh Patel
> >> >> >> > > >> >> >> ><pragnesh.patel@sifive.com>
> >> >> >> > > >> >> >> >wrote:
> >> >> >> > > >> >> >> >>
> >> >> >> > > >> >> >> >> Hi Jagan,
> >> >> >> > > >> >> >> >>
> >> >> >> > > >> >> >> >> >-----Original Message-----
> >> >> >> > > >> >> >> >> >From: Jagan Teki <jagan@amarulasolutions.com>
> >> >> >> > > >> >> >> >> >Sent: 02 May 2020 21:49
> >> >> >> > > >> >> >> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> >> >> > > >> >> >> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish
> >> >> >> > > >> >> >> >> >Patra <atish.patra@wdc.com>; Palmer Dabbelt
> >> >> >> > > >> >> ><palmerdabbelt@google.com>;
> >> >> >> > > >> >> >> >Bin
> >> >> >> > > >> >> >> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
> >> >> >> > > >> >> >> ><paul.walmsley@sifive.com>;
> >> >> >> > > >> >> >> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>;
> >> >> >> > > >> >> >> >> >Anup Patel <anup.patel@wdc.com>; Sagar Kadam
> >> >> >> > > ><sagar.kadam@sifive.com>;
> >> >> >> > > >> >> >> >> >Rick
> >> >> >> > > >> >> >> >Chen
> >> >> >> > > >> >> >> >> ><rick@andestech.com>
> >> >> >> > > >> >> >> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540:
> >> >> >> > > >> >> >> >> >Enable L2 Cache in U-Boot
> >> >> >> > > >> >> >> >> >
> >> >> >> > > >> >> >> >> >[External Email] Do not click links or
> >> >> >> > > >> >> >> >> >attachments unless you recognize the sender and
> >> >> >> > > >> >> >> >> >know the content is safe
> >> >> >> > > >> >> >> >> >
> >> >> >> > > >> >> >> >> >On Sat, May 2, 2020 at 3:39 PM Pragnesh Patel
> >> >> >> > > >> >> >> >> ><pragnesh.patel@sifive.com>
> >> >> >> > > >> >> >> >> >wrote:
> >> >> >> > > >> >> >> >> >>
> >> >> >> > > >> >> >> >> >> Add L2 cache node to enable cache ways from
> >> >> >> > > >> >> >> >> >> U-Boot
> >> >> >> > > >> >> >> >> >
> >> >> >> > > >> >> >> >> >This and 20/22 doesn't relate to SPL MMC boot?,
> >> >> >> > > >> >> >> >> >if yes please send them separately.
> >> >> >> > > >> >> >> >>
> >> >> >> > > >> >> >> >> This series is for replacing FSBL and all the
> >> >> >> > > >> >> >> >> patches are related to
> >> >> >> > > >that.
> >> >> >> > > >> >> >> >> IMHO it's better to add all FSBL functionality in one
> >series.
> >> >> >> > > >> >> >> >
> >> >> >> > > >> >> >> >You mean does it break existing FSBL flow? if yes
> >> >> >> > > >> >> >> >add proper commit message, but I am able to boot
> >> >> >> > > >> >> >> >SPL MMC w/o
> >> >> >this?
> >> >> >> > > >> >> >>
> >> >> >> > > >> >> >> Cache ways are enabled by FSBL also and if I will
> >> >> >> > > >> >> >> send cache ways patches separately then it will a
> >> >> >> > > >> >> >> duplicate way of enabling cache ways if
> >> >> >> > > >> >> >someone using FSBL.
> >> >> >> > > >> >> >
> >> >> >> > > >> >> >Sorry I didn't get you.
> >> >> >> > > >> >> >
> >> >> >> > > >> >> >If we cannot include these changes does U-Boot SPL
> >> >> >> > > >> >> >break existing
> >> >> >FSBL?
> >> >> >> > > >> >>
> >> >> >> > > >> >> No, U-Boot SPL does not break without this.
> >> >> >> > > >> >>
> >> >> >> > > >> >> As of now, we also want to support FSBL flow and FSBL
> >> >> >> > > >> >> also enabled the Cache ways for U-Boot proper and if
> >> >> >> > > >> >> someone use this patches of
> >> >> >> > > >> >> L2 cache enable ways will FSBL then it will be a
> >> >> >> > > >> >> duplicate work of cache enable
> >> >> >> > > >> >ways.
> >> >> >> > > >> >
> >> >> >> > > >> >My question is what if we don't add this change at all?
> >> >> >> > > >>
> >> >> >> > > >> U-Boot SPL will work without L2 cache enable patches but
> >> >> >> > > >> why we want to
> >> >> >> > > >do this.
> >> >> >> > > >> This series is not just for SPL mmc booting but also
> >> >> >> > > >> replacing FSBL functionality so better to cover all FSBL
> >> >> >> > > >> stuff in one
> >> >series.
> >> >> >> > > >
> >> >> >> > > >So, FSBL flow would break if we add U-Boot SPL so this
> >> >> >> > > >patch fixing by enabling cache's explicitly to avoid that break. isn't
> >it?
> >> >> >> > >
> >> >> >> > > No, you are not getting this.
> >> >> >> > >
> >> >> >> > > Initially FSBL enable the cache ways before U-Boot SPL.
> >> >> >> > > https://github.com/sifive/freedom-u540-c000-bootloader/blob/
> >> >> >> > > mas
> >> >> >> > > ter
> >> >> >> > > /fsbl/main.c#L428
> >> >> >> >
> >> >> >> > This is not Mainline. enabling cache's are a new thing for
> >> >> >> > Mainline for you. So this code is pretty much new. Is that clear?
> >> >> >> >
> >> >> >> > >
> >> >> >> > > Now U-Boot SPL doing the same in [v7 19/22] and [v7 20/22].
> >> >> >> >
> >> >> >> > But these two patches enable caches for U-Boot proper in case
> >> >> >> > of U-Boot SPL flow and U-Boot in case of FSBL. am I correct?
> >> >> >> > if so this code is purely U-Boot specific neither FSBL nor U-Boot SPL.
> >> >> >> > then what is the problem of having a series or separate
> >> >> >> > patches with cache enablement.
> >> >> >>
> >> >> >> My understanding is that:
> >> >> >>
> >> >> >> 1. This patch series is adding SiFive FU540 U-Boot SPL support 2.
> >> >> >> The purpose is to replace SiFive provided FSBL with U-Boot SPL 3.
> >> >> >> SiFive FSBL initializes L2 cache before loading next stage
> >> >> >> payload 4. U-Boot SPL should provide the same features, like
> >> >> >> initializing
> >> >> >> L2 cache
> >> >> >
> >> >> >So, you mean U-Boot SPL would enable the cache similar like FSBL
> >> >> >does
> >> >right?
> >> >> >but this patch [1] enabling cache only for U-Boot not SPL isn't it?
> >> >> >
> >> >> >[1]
> >> >>
> >>
> >>>https://patchwork.ozlabs.org/project/uboot/patch/20200502100628.2480
> >> >>9
> >> >> >-
> >> >> >20-pragnesh.patel at sifive.com/
> >> >>
> >> >> Yes, you are right. Cache ways are enabled by U-Boot proper not by
> >> >> U-Boot
> >> >SPL.
> >> >> Will pull cache related patches out of this series and send as
> >> >> separate
> >> >patches.
> >> >>
> >> >
> >> >Now I am confused. Are you saying that FSBL does NOT enable L2 cache?
> >> >Based on your statement in this review thread I think you basically
> >> >wanted to replace FSBL with the same featured U-Boot SPL.
> >>
> >> For FSBL flow,
> >> Cache ways are enabled by FSBL and with this series cache ways are
> >> again enabled by U-Boot Proper. Once this series has been merged, we
> >> may remove cache enable ways from FSBL or I Will apply check in U-Boot
> >proper for already enabled cache ways.
> >>
> >> For SPL flow,
> >> Cache ways are enabled by U-Boot proper. We can not enable cache ways
> >> from U-Boot SPL because SPL is running from L2 LIM.
> >>
> >
> >Thanks for the clarification. I wonder where is the FSBL running. Can U-Boot
> >SPL run from where FSBL is running instead of L2 LIM?
>
> FSBL and U-Boot SPL running from the same location.
>
> L2 cache is of 2 MB (16 cache ways) and 1 cache way is of 128 KB.
>
> At runtime, FSBL is located on the latest way of L2 cache. Therefore,
> FSBL can only enable the first 15 L2 cache ways to avoid corrupt itself.
> (Way 0 is enabled by default)
> https://github.com/sifive/freedom-u540-c000-bootloader/blob/master/fsbl/main.c#L428
>
> U-Boot SPL is bigger than FSBL so can not fit in 1 cache way, so I decided to enable all cache ways from
> U-Boot proper.
>
Thanks! This makes sense.
> >
> >> @Jagan Teki Sorry for my misunderstanding, U-Boot SPL got stuck in my
> >mind.
Regards,
Bin
^ permalink raw reply [flat|nested] 118+ messages in thread
* [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
2020-05-11 9:55 ` Pragnesh Patel
2020-05-11 10:10 ` Bin Meng
@ 2020-05-12 7:45 ` Jagan Teki
1 sibling, 0 replies; 118+ messages in thread
From: Jagan Teki @ 2020-05-12 7:45 UTC (permalink / raw)
To: u-boot
On Mon, May 11, 2020 at 3:25 PM Pragnesh Patel
<pragnesh.patel@sifive.com> wrote:
>
> >-----Original Message-----
> >From: Bin Meng <bmeng.cn@gmail.com>
> >Sent: 11 May 2020 15:17
> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >Cc: Jagan Teki <jagan@amarulasolutions.com>; U-Boot-Denx <u-
> >boot at lists.denx.de>; Atish Patra <atish.patra@wdc.com>; Palmer Dabbelt
> ><palmerdabbelt@google.com>; Paul Walmsley <paul.walmsley@sifive.com>;
> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>; Rick Chen
> ><rick@andestech.com>
> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot
> >
> >[External Email] Do not click links or attachments unless you recognize the
> >sender and know the content is safe
> >
> >Hi Pragnesh,
> >
> >On Mon, May 11, 2020 at 5:34 PM Pragnesh Patel
> ><pragnesh.patel@sifive.com> wrote:
> >>
> >> >-----Original Message-----
> >> >From: Jagan Teki <jagan@amarulasolutions.com>
> >> >Sent: 11 May 2020 14:35
> >> >To: Bin Meng <bmeng.cn@gmail.com>
> >> >Cc: Pragnesh Patel <pragnesh.patel@sifive.com>; U-Boot-Denx <u-
> >> >boot at lists.denx.de>; Atish Patra <atish.patra@wdc.com>; Palmer
> >> >Dabbelt <palmerdabbelt@google.com>; Paul Walmsley
> >> ><paul.walmsley@sifive.com>; Troy Benjegerdes
> >> ><troy.benjegerdes@sifive.com>; Anup Patel <anup.patel@wdc.com>; Sagar
> >> >Kadam <sagar.kadam@sifive.com>; Rick Chen <rick@andestech.com>
> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in
> >> >U-Boot
> >> >
> >> >[External Email] Do not click links or attachments unless you
> >> >recognize the sender and know the content is safe
> >> >
> >> >Hi Bin,
> >> >
> >> >On Mon, May 11, 2020 at 2:30 PM Bin Meng <bmeng.cn@gmail.com>
> >wrote:
> >> >>
> >> >> Hi Jagan,
> >> >>
> >> >> On Mon, May 11, 2020 at 4:48 PM Jagan Teki
> >> ><jagan@amarulasolutions.com> wrote:
> >> >> >
> >> >> > On Mon, May 11, 2020 at 1:15 PM Pragnesh Patel
> >> >> > <pragnesh.patel@sifive.com> wrote:
> >> >> > >
> >> >> > > >-----Original Message-----
> >> >> > > >From: Jagan Teki <jagan@amarulasolutions.com>
> >> >> > > >Sent: 11 May 2020 12:56
> >> >> > > >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> >> > > >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> >> >> > > ><atish.patra@wdc.com>; Palmer Dabbelt
> >> ><palmerdabbelt@google.com>;
> >> >> > > >Bin Meng <bmeng.cn@gmail.com>; Paul Walmsley
> >> >> > > ><paul.walmsley@sifive.com>; Troy Benjegerdes
> >> >> > > ><troy.benjegerdes@sifive.com>; Anup Patel
> >> >> > > ><anup.patel@wdc.com>; Sagar Kadam <sagar.kadam@sifive.com>;
> >> >> > > >Rick Chen <rick@andestech.com>
> >> >> > > >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2
> >> >> > > >Cache in U-Boot
> >> >> > > >
> >> >> > > >[External Email] Do not click links or attachments unless you
> >> >> > > >recognize the sender and know the content is safe
> >> >> > > >
> >> >> > > >On Mon, May 11, 2020 at 12:37 PM Pragnesh Patel
> >> >> > > ><pragnesh.patel@sifive.com> wrote:
> >> >> > > >>
> >> >> > > >> >-----Original Message-----
> >> >> > > >> >From: Jagan Teki <jagan@amarulasolutions.com>
> >> >> > > >> >Sent: 11 May 2020 12:25
> >> >> > > >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> >> > > >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> >> >> > > >> ><atish.patra@wdc.com>; Palmer Dabbelt
> >> >> > > >> ><palmerdabbelt@google.com>;
> >> >> > > >Bin
> >> >> > > >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
> >> >> > > ><paul.walmsley@sifive.com>;
> >> >> > > >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup Patel
> >> >> > > >> ><anup.patel@wdc.com>; Sagar Kadam
> ><sagar.kadam@sifive.com>;
> >> >> > > >> >Rick
> >> >> > > >Chen
> >> >> > > >> ><rick@andestech.com>
> >> >> > > >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable L2
> >> >> > > >> >Cache in U-Boot
> >> >> > > >> >
> >> >> > > >> >[External Email] Do not click links or attachments unless
> >> >> > > >> >you recognize the sender and know the content is safe
> >> >> > > >> >
> >> >> > > >> >On Mon, May 11, 2020 at 11:35 AM Pragnesh Patel
> >> >> > > >> ><pragnesh.patel@sifive.com> wrote:
> >> >> > > >> >>
> >> >> > > >> >> >-----Original Message-----
> >> >> > > >> >> >From: Jagan Teki <jagan@amarulasolutions.com>
> >> >> > > >> >> >Sent: 10 May 2020 15:02
> >> >> > > >> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> >> > > >> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> >> >> > > >> >> ><atish.patra@wdc.com>; Palmer Dabbelt
> >> >> > > ><palmerdabbelt@google.com>;
> >> >> > > >> >Bin
> >> >> > > >> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
> >> >> > > >> ><paul.walmsley@sifive.com>;
> >> >> > > >> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup
> >> >> > > >> >> >Patel <anup.patel@wdc.com>; Sagar Kadam
> >> ><sagar.kadam@sifive.com>;
> >> >> > > >> >> >Rick
> >> >> > > >> >Chen
> >> >> > > >> >> ><rick@andestech.com>
> >> >> > > >> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540: Enable
> >> >> > > >> >> >L2 Cache in U-Boot
> >> >> > > >> >> >
> >> >> > > >> >> >[External Email] Do not click links or attachments
> >> >> > > >> >> >unless you recognize the sender and know the content is
> >> >> > > >> >> >safe
> >> >> > > >> >> >
> >> >> > > >> >> >On Sun, May 3, 2020 at 12:57 PM Pragnesh Patel
> >> >> > > >> >> ><pragnesh.patel@sifive.com> wrote:
> >> >> > > >> >> >>
> >> >> > > >> >> >> Hi jagan,
> >> >> > > >> >> >>
> >> >> > > >> >> >> >-----Original Message-----
> >> >> > > >> >> >> >From: Jagan Teki <jagan@amarulasolutions.com>
> >> >> > > >> >> >> >Sent: 02 May 2020 22:43
> >> >> > > >> >> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> >> > > >> >> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish Patra
> >> >> > > >> >> >> ><atish.patra@wdc.com>; Palmer Dabbelt
> >> >> > > >> ><palmerdabbelt@google.com>;
> >> >> > > >> >> >Bin
> >> >> > > >> >> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
> >> >> > > >> >> ><paul.walmsley@sifive.com>;
> >> >> > > >> >> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>; Anup
> >> >> > > >> >> >> >Patel <anup.patel@wdc.com>; Sagar Kadam
> >> >> > > >> >> >> ><sagar.kadam@sifive.com>; Rick
> >> >> > > >> >> >Chen
> >> >> > > >> >> >> ><rick@andestech.com>
> >> >> > > >> >> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540:
> >> >> > > >> >> >> >Enable
> >> >> > > >> >> >> >L2 Cache in U-Boot
> >> >> > > >> >> >> >
> >> >> > > >> >> >> >[External Email] Do not click links or attachments
> >> >> > > >> >> >> >unless you recognize the sender and know the content
> >> >> > > >> >> >> >is safe
> >> >> > > >> >> >> >
> >> >> > > >> >> >> >On Sat, May 2, 2020 at 10:12 PM Pragnesh Patel
> >> >> > > >> >> >> ><pragnesh.patel@sifive.com>
> >> >> > > >> >> >> >wrote:
> >> >> > > >> >> >> >>
> >> >> > > >> >> >> >> Hi Jagan,
> >> >> > > >> >> >> >>
> >> >> > > >> >> >> >> >-----Original Message-----
> >> >> > > >> >> >> >> >From: Jagan Teki <jagan@amarulasolutions.com>
> >> >> > > >> >> >> >> >Sent: 02 May 2020 21:49
> >> >> > > >> >> >> >> >To: Pragnesh Patel <pragnesh.patel@sifive.com>
> >> >> > > >> >> >> >> >Cc: U-Boot-Denx <u-boot@lists.denx.de>; Atish
> >> >> > > >> >> >> >> >Patra <atish.patra@wdc.com>; Palmer Dabbelt
> >> >> > > >> >> ><palmerdabbelt@google.com>;
> >> >> > > >> >> >> >Bin
> >> >> > > >> >> >> >> >Meng <bmeng.cn@gmail.com>; Paul Walmsley
> >> >> > > >> >> >> ><paul.walmsley@sifive.com>;
> >> >> > > >> >> >> >> >Troy Benjegerdes <troy.benjegerdes@sifive.com>;
> >> >> > > >> >> >> >> >Anup Patel <anup.patel@wdc.com>; Sagar Kadam
> >> >> > > ><sagar.kadam@sifive.com>;
> >> >> > > >> >> >> >> >Rick
> >> >> > > >> >> >> >Chen
> >> >> > > >> >> >> >> ><rick@andestech.com>
> >> >> > > >> >> >> >> >Subject: Re: [PATCH v7 19/22] sifive: dts: fu540:
> >> >> > > >> >> >> >> >Enable L2 Cache in U-Boot
> >> >> > > >> >> >> >> >
> >> >> > > >> >> >> >> >[External Email] Do not click links or attachments
> >> >> > > >> >> >> >> >unless you recognize the sender and know the
> >> >> > > >> >> >> >> >content is safe
> >> >> > > >> >> >> >> >
> >> >> > > >> >> >> >> >On Sat, May 2, 2020 at 3:39 PM Pragnesh Patel
> >> >> > > >> >> >> >> ><pragnesh.patel@sifive.com>
> >> >> > > >> >> >> >> >wrote:
> >> >> > > >> >> >> >> >>
> >> >> > > >> >> >> >> >> Add L2 cache node to enable cache ways from
> >> >> > > >> >> >> >> >> U-Boot
> >> >> > > >> >> >> >> >
> >> >> > > >> >> >> >> >This and 20/22 doesn't relate to SPL MMC boot?, if
> >> >> > > >> >> >> >> >yes please send them separately.
> >> >> > > >> >> >> >>
> >> >> > > >> >> >> >> This series is for replacing FSBL and all the
> >> >> > > >> >> >> >> patches are related to
> >> >> > > >that.
> >> >> > > >> >> >> >> IMHO it's better to add all FSBL functionality in one series.
> >> >> > > >> >> >> >
> >> >> > > >> >> >> >You mean does it break existing FSBL flow? if yes add
> >> >> > > >> >> >> >proper commit message, but I am able to boot SPL MMC
> >> >> > > >> >> >> >w/o
> >> >this?
> >> >> > > >> >> >>
> >> >> > > >> >> >> Cache ways are enabled by FSBL also and if I will send
> >> >> > > >> >> >> cache ways patches separately then it will a duplicate
> >> >> > > >> >> >> way of enabling cache ways if
> >> >> > > >> >> >someone using FSBL.
> >> >> > > >> >> >
> >> >> > > >> >> >Sorry I didn't get you.
> >> >> > > >> >> >
> >> >> > > >> >> >If we cannot include these changes does U-Boot SPL break
> >> >> > > >> >> >existing
> >> >FSBL?
> >> >> > > >> >>
> >> >> > > >> >> No, U-Boot SPL does not break without this.
> >> >> > > >> >>
> >> >> > > >> >> As of now, we also want to support FSBL flow and FSBL
> >> >> > > >> >> also enabled the Cache ways for U-Boot proper and if
> >> >> > > >> >> someone use this patches of
> >> >> > > >> >> L2 cache enable ways will FSBL then it will be a
> >> >> > > >> >> duplicate work of cache enable
> >> >> > > >> >ways.
> >> >> > > >> >
> >> >> > > >> >My question is what if we don't add this change at all?
> >> >> > > >>
> >> >> > > >> U-Boot SPL will work without L2 cache enable patches but why
> >> >> > > >> we want to
> >> >> > > >do this.
> >> >> > > >> This series is not just for SPL mmc booting but also
> >> >> > > >> replacing FSBL functionality so better to cover all FSBL stuff in one
> >series.
> >> >> > > >
> >> >> > > >So, FSBL flow would break if we add U-Boot SPL so this patch
> >> >> > > >fixing by enabling cache's explicitly to avoid that break. isn't it?
> >> >> > >
> >> >> > > No, you are not getting this.
> >> >> > >
> >> >> > > Initially FSBL enable the cache ways before U-Boot SPL.
> >> >> > > https://github.com/sifive/freedom-u540-c000-bootloader/blob/mas
> >> >> > > ter
> >> >> > > /fsbl/main.c#L428
> >> >> >
> >> >> > This is not Mainline. enabling cache's are a new thing for
> >> >> > Mainline for you. So this code is pretty much new. Is that clear?
> >> >> >
> >> >> > >
> >> >> > > Now U-Boot SPL doing the same in [v7 19/22] and [v7 20/22].
> >> >> >
> >> >> > But these two patches enable caches for U-Boot proper in case of
> >> >> > U-Boot SPL flow and U-Boot in case of FSBL. am I correct? if so
> >> >> > this code is purely U-Boot specific neither FSBL nor U-Boot SPL.
> >> >> > then what is the problem of having a series or separate patches
> >> >> > with cache enablement.
> >> >>
> >> >> My understanding is that:
> >> >>
> >> >> 1. This patch series is adding SiFive FU540 U-Boot SPL support 2.
> >> >> The purpose is to replace SiFive provided FSBL with U-Boot SPL 3.
> >> >> SiFive FSBL initializes L2 cache before loading next stage payload
> >> >> 4. U-Boot SPL should provide the same features, like initializing
> >> >> L2 cache
> >> >
> >> >So, you mean U-Boot SPL would enable the cache similar like FSBL does
> >right?
> >> >but this patch [1] enabling cache only for U-Boot not SPL isn't it?
> >> >
> >> >[1]
> >>
> >>https://patchwork.ozlabs.org/project/uboot/patch/20200502100628.24809
> >> >-
> >> >20-pragnesh.patel at sifive.com/
> >>
> >> Yes, you are right. Cache ways are enabled by U-Boot proper not by U-Boot
> >SPL.
> >> Will pull cache related patches out of this series and send as separate
> >patches.
> >>
> >
> >Now I am confused. Are you saying that FSBL does NOT enable L2 cache?
> >Based on your statement in this review thread I think you basically wanted to
> >replace FSBL with the same featured U-Boot SPL.
>
> For FSBL flow,
> Cache ways are enabled by FSBL and with this series cache ways are again enabled by U-Boot
> Proper. Once this series has been merged, we may remove cache enable ways from FSBL or I
> Will apply check in U-Boot proper for already enabled cache ways.
>
> For SPL flow,
> Cache ways are enabled by U-Boot proper. We can not enable cache ways from U-Boot SPL because
> SPL is running from L2 LIM.
>
> @Jagan Teki Sorry for my misunderstanding, U-Boot SPL got stuck in my mind.
No problem at all, It is just a discussion of how things would get
into perfect shape. Why I was more concerned about patches should be
out of the series which are unrelated is you can get a clean series of
what changes would require for U-Boot SPL to support. This is general
upstream workflow. That would indeed be easy for reviewers to
understand and comment quickly. Moreover you could have a clear
history and better bisectability in future, thanks!
Jagan.
^ permalink raw reply [flat|nested] 118+ messages in thread
end of thread, other threads:[~2020-05-12 7:45 UTC | newest]
Thread overview: 118+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-05-02 10:06 [PATCH v7 00/22] RISC-V SiFive FU540 support SPL Pragnesh Patel
2020-05-02 10:06 ` [PATCH v7 01/22] misc: add driver for the SiFive otp controller Pragnesh Patel
2020-05-02 12:28 ` Bin Meng
2020-05-02 15:37 ` Jagan Teki
2020-05-02 15:42 ` Pragnesh Patel
2020-05-02 15:50 ` Jagan Teki
2020-05-02 16:18 ` Pragnesh Patel
2020-05-10 9:04 ` Jagan Teki
2020-05-11 5:39 ` Pragnesh Patel
2020-05-02 10:06 ` [PATCH v7 02/22] riscv: sifive: fu540: Use OTP DM driver for serial environment variable Pragnesh Patel
2020-05-02 12:28 ` Bin Meng
2020-05-02 10:06 ` [PATCH v7 03/22] riscv: Add _image_binary_end for SPL Pragnesh Patel
2020-05-02 12:28 ` Bin Meng
2020-05-02 10:06 ` [PATCH v7 04/22] lib: Makefile: build crc7.c when CONFIG_MMC_SPI Pragnesh Patel
2020-05-02 10:29 ` Heinrich Schuchardt
2020-05-02 11:47 ` Bin Meng
2020-05-02 12:58 ` Heinrich Schuchardt
2020-05-02 15:33 ` Jagan Teki
2020-05-04 5:45 ` Pragnesh Patel
2020-05-05 15:55 ` Pragnesh Patel
2020-05-08 5:59 ` Pragnesh Patel
2020-05-03 9:54 ` Pragnesh Patel
2020-05-02 12:28 ` Bin Meng
2020-05-02 10:06 ` [PATCH v7 05/22] riscv: sifive: dts: fu540: Add board -u-boot.dtsi files Pragnesh Patel
2020-05-02 10:06 ` [PATCH v7 06/22] sifive: fu540: add ddr driver Pragnesh Patel
2020-05-02 12:28 ` Bin Meng
2020-05-02 15:59 ` Jagan Teki
2020-05-02 16:32 ` Pragnesh Patel
2020-05-02 10:06 ` [PATCH v7 07/22] sifive: dts: fu540: Add DDR controller and phy register settings Pragnesh Patel
2020-05-02 12:28 ` Bin Meng
2020-05-02 14:41 ` Pragnesh Patel
2020-05-02 10:06 ` [PATCH v7 08/22] riscv: sifive: dts: fu540: add U-Boot dmc node Pragnesh Patel
2020-05-02 12:29 ` Bin Meng
2020-05-02 10:06 ` [PATCH v7 09/22] clk: sifive: fu540-prci: Add clock enable and disable ops Pragnesh Patel
2020-05-02 12:29 ` Bin Meng
2020-05-02 10:06 ` [PATCH v7 10/22] clk: sifive: fu540-prci: ddr and ethernet clock initialization in SPL Pragnesh Patel
2020-05-02 12:28 ` Bin Meng
2020-05-02 14:49 ` Pragnesh Patel
2020-05-09 11:29 ` Pragnesh Patel
2020-05-02 16:14 ` Jagan Teki
2020-05-02 16:35 ` Pragnesh Patel
2020-05-02 16:44 ` Jagan Teki
2020-05-03 8:57 ` Pragnesh Patel
2020-05-02 10:06 ` [PATCH v7 11/22] riscv: dts: sifive: Sync hifive-unleashed-a00 dts from linux Pragnesh Patel
2020-05-02 10:06 ` [PATCH v7 12/22] sifive: dts: fu540: Enable gpio in U-Boot SPL Pragnesh Patel
2020-05-02 10:06 ` [PATCH v7 13/22] riscv: cpu: fu540: Add support for cpu fu540 Pragnesh Patel
2020-05-02 12:32 ` Bin Meng
2020-05-02 14:38 ` Pragnesh Patel
2020-05-02 16:34 ` Jagan Teki
2020-05-03 9:16 ` Pragnesh Patel
2020-05-02 10:06 ` [PATCH v7 14/22] riscv: Add place-holder for driver compilation Pragnesh Patel
2020-05-02 12:43 ` Bin Meng
2020-05-02 16:27 ` Jagan Teki
2020-05-03 9:17 ` Pragnesh Patel
2020-05-10 9:12 ` Jagan Teki
2020-05-11 5:58 ` Pragnesh Patel
2020-05-11 6:53 ` Jagan Teki
2020-05-11 7:10 ` Pragnesh Patel
2020-05-02 10:06 ` [PATCH v7 15/22] riscv: sifive: dts: fu540: Add clock for cpus node Pragnesh Patel
2020-05-02 12:43 ` Bin Meng
2020-05-02 16:50 ` Jagan Teki
2020-05-03 8:55 ` Pragnesh Patel
2020-05-02 10:06 ` [PATCH v7 16/22] riscv: Enable cpu clock if it is present Pragnesh Patel
2020-05-02 12:55 ` Bin Meng
2020-05-02 18:15 ` Sean Anderson
2020-05-03 7:12 ` Pragnesh Patel
2020-05-03 17:17 ` Sean Anderson
2020-05-04 5:20 ` Pragnesh Patel
2020-05-02 10:06 ` [PATCH v7 17/22] riscv: sifive: fu540: add SPL configuration Pragnesh Patel
2020-05-02 12:55 ` Bin Meng
2020-05-02 10:06 ` [PATCH v7 18/22] configs: fu540: Add config options for U-Boot SPL Pragnesh Patel
2020-05-02 12:55 ` Bin Meng
2020-05-02 14:37 ` Pragnesh Patel
2020-05-02 17:04 ` Jagan Teki
2020-05-02 16:51 ` Jagan Teki
2020-05-04 15:48 ` Pragnesh Patel
2020-05-02 17:15 ` Jagan Teki
2020-05-03 7:20 ` Pragnesh Patel
2020-05-02 10:06 ` [PATCH v7 19/22] sifive: dts: fu540: Enable L2 Cache in U-Boot Pragnesh Patel
2020-05-02 16:18 ` Jagan Teki
2020-05-02 16:42 ` Pragnesh Patel
2020-05-02 17:13 ` Jagan Teki
2020-05-03 7:27 ` Pragnesh Patel
2020-05-10 9:31 ` Jagan Teki
2020-05-11 6:05 ` Pragnesh Patel
2020-05-11 6:54 ` Jagan Teki
2020-05-11 7:07 ` Pragnesh Patel
2020-05-11 7:25 ` Jagan Teki
2020-05-11 7:45 ` Pragnesh Patel
2020-05-11 8:48 ` Jagan Teki
2020-05-11 9:00 ` Bin Meng
2020-05-11 9:05 ` Jagan Teki
2020-05-11 9:34 ` Pragnesh Patel
2020-05-11 9:47 ` Bin Meng
2020-05-11 9:55 ` Pragnesh Patel
2020-05-11 10:10 ` Bin Meng
2020-05-11 10:35 ` Pragnesh Patel
2020-05-12 1:20 ` Bin Meng
2020-05-12 7:45 ` Jagan Teki
2020-05-02 10:06 ` [PATCH v7 20/22] riscv: sifive: fu540: enable all cache ways from U-Boot proper Pragnesh Patel
2020-05-02 12:55 ` Bin Meng
2020-05-02 14:34 ` Pragnesh Patel
2020-05-02 10:06 ` [PATCH v7 21/22] doc: sifive: fu540: Add description for OpenSBI generic platform Pragnesh Patel
2020-05-02 12:55 ` Bin Meng
2020-05-02 14:30 ` Pragnesh Patel
2020-05-02 15:16 ` Bin Meng
2020-05-02 15:22 ` Pragnesh Patel
2020-05-02 15:27 ` Bin Meng
2020-05-02 15:29 ` Pragnesh Patel
2020-05-03 4:36 ` Anup Patel
2020-05-02 10:06 ` [PATCH v7 22/22] doc: sifive: fu540: Add description for RISC-V FU540 U-Boot SPL Pragnesh Patel
2020-05-02 12:55 ` Bin Meng
2020-05-02 16:22 ` Jagan Teki
2020-05-02 16:53 ` Pragnesh Patel
2020-05-03 4:34 ` Anup Patel
2020-05-03 6:13 ` Pragnesh Patel
2020-05-02 17:18 ` [PATCH v7 00/22] RISC-V SiFive FU540 support SPL Jagan Teki
2020-05-03 7:19 ` Pragnesh Patel
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.