* Re: [OpenWrt-Devel] ATH10K VLAN firmware issue
@ 2016-11-04 22:23 ` Ben Greear
0 siblings, 0 replies; 54+ messages in thread
From: Ben Greear @ 2016-11-04 22:23 UTC (permalink / raw)
To: yu-chieh kung, Bruno Antunes
Cc: Mauro Mozzarelli, linux-wireless, OpenWrt Development List, ath10k
The bug appears that vlan-tx-stripping is unconditionally enabled in
at least my firmware. I have re-compiled w/out that flag set, and it appears
to work for me.
Please download this firmware, rename it firmware-2.bin, make sure you remove/rename
any firmware-5.bin (etc) so mine will load, and see if that fixes your problem.
Please note that it is very likely you will have to use same MAC address
for the VLAN devices that the underlying station uses in order for this to work.
https://www.candelatech.com/downloads/tmp/firmware-2-full-community.bin
Thanks,
Ben
On 11/04/2016 02:50 PM, Ben Greear wrote:
> I can reproduce this in my CT firmware. I'll see if I can fix it,
> but for stock firmware, it might be that changing the driver to use Ethernet packet type
> of native-wifi would make .1q vlans work.
>
> Thanks,
> Ben
>
> On 11/04/2016 10:28 AM, yu-chieh kung wrote:
>> I met the same problem before,
>> if i modify the 1q header to other value (0xaa00) before go into firmware.
>> I can capture the packet in the air
>> I think the vlan packet is dropped in firmware.
>>
>> 2016-11-04 22:41 GMT+08:00 Bruno Antunes <baantunes@gmail.com>:
>>> On 4 November 2016 at 14:18, Mauro Mozzarelli <openwrt@ezplanet.net> wrote:
>>>> Since the capability is implemented in software you might be testing the
>>>> limit of your router's CPU i/o speed.
>>>
>>> By loading the module in rawmode?
>>>
>>> The AP is an APU and Sta is an APU2.
>>>
>>>>
>>>>
>>>>
>>>> On 04/11/16 14:13, Bruno Antunes wrote:
>>>>>
>>>>> Hi all,
>>>>>
>>>>> Old thread but I think the issue is still present.
>>>>>
>>>>> I'm running a setup with VLANs with WDS and ath10k cards.
>>>>>
>>>>> To make it work both cards must be loaded in rawmode, AP
>>>>> and Sta, and with no security.
>>>>>
>>>>> I'm using a OpenWrt trunk r49941 and the most recent firmware,
>>>>> 10.2.4.70.58, from Kalle ath10k firmware tree.
>>>>>
>>>>> Although it works the throughput is very bad.
>>>>> Are there any alternatives to improve the throughput.
>>>>>
>>>>> Best Regards,
>>>>> Bruno
>>>>>
>>>>> On 9 December 2015 at 17:24, voncken <cedric.voncken@acksys.fr> wrote:
>>>>>>
>>>>>>
>>>>>>> -----Message d'origine-----
>>>>>>> De : Ben Greear [mailto:greearb@candelatech.com]
>>>>>>> Envoyé : mercredi 9 décembre 2015 16:34
>>>>>>> À : Cedric VONCKEN; ath10k@lists.infradead.org; linux-wireless
>>>>>>> Objet : Re: ATH10K VLAN firmware issue
>>>>>>>
>>>>>>> This only happens when you use STA + WDS, or is .1q broken for you in
>>>>>>> other cases as well?
>>>>>>
>>>>>> No, this issue occurs in all modes (STA, STA + WDS, AP).
>>>>>>
>>>>>> Thanks
>>>>>>
>>>>>> Cedric.
>>>>>>
>>>>>>> Thanks,
>>>>>>> Ben
>>>>>>>
>>>>>>> On 12/08/2015 06:29 AM, Cedric VONCKEN wrote:
>>>>>>>>
>>>>>>>> I'm testing to transmit frame with 802.1q tag (VLAN).
>>>>>>>>
>>>>>>>> My client is set in STA + WDS and the netdev is bridged with eth0.
>>>>>>>> I have a computer with vlan configuration set connected to the STA
>>>>>>>> eth0.
>>>>>>>>
>>>>>>>> If I try to transmit frames with 802.1q tag, the frames are not
>>>>>>
>>>>>> sent.
>>>>>>>>
>>>>>>>> I checked with wireless sniffer, and I don't see the frame with
>>>>>>>> VLAN
>>>>>>>> tag (the frames without VLAN tag are sent).
>>>>>>>>
>>>>>>>> I tested with firmware 10.2.4.70.14-2 from kale github,
>>>>>>>> 10.1.467-ct-com-full-015 from candelatech and 10.2.4.70-2 from
>>>>>>>> openwrt, and in all cases I have the same issue.
>>>>>>>>
>>>>>>>> Thanks for your help.
>>>>>>>>
>>>>>>>>
>>>>>>>> --
>>>>>>>> To unsubscribe from this list: send the line "unsubscribe
>>>>>>>> linux-wireless" in the body of a message to majordomo@vger.kernel.org
>>>>>>>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>>>>>>>>
>>>>>>> --
>>>>>>> Ben Greear <greearb@candelatech.com>
>>>>>>> Candela Technologies Inc http://www.candelatech.com
>>>>>>
>>>>>> --
>>>>>> To unsubscribe from this list: send the line "unsubscribe linux-wireless"
>>>>>> in
>>>>>> the body of a message to majordomo@vger.kernel.org
>>>>>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>>>>>
>>>>> _______________________________________________
>>>>> openwrt-devel mailing list
>>>>> openwrt-devel@lists.openwrt.org
>>>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>>>>
>>>> _______________________________________________
>>>> openwrt-devel mailing list
>>>> openwrt-devel@lists.openwrt.org
>>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>>>
>>> _______________________________________________
>>> ath10k mailing list
>>> ath10k@lists.infradead.org
>>> http://lists.infradead.org/mailman/listinfo/ath10k
>>
>
>
--
Ben Greear <greearb@candelatech.com>
Candela Technologies Inc http://www.candelatech.com
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 54+ messages in thread
* Re: [OpenWrt-Devel] ATH10K VLAN firmware issue
2016-11-04 22:23 ` Ben Greear
@ 2016-11-05 8:05 ` Sebastian Gottschall
-1 siblings, 0 replies; 54+ messages in thread
From: Sebastian Gottschall @ 2016-11-05 8:05 UTC (permalink / raw)
To: Ben Greear, yu-chieh kung, Bruno Antunes
Cc: Mauro Mozzarelli, linux-wireless, OpenWrt Development List, ath10k
would be good if qca can fix this bug finally in all available
firmwares. its a very annoying issue since a long time
Sebastian
Am 04.11.2016 um 23:23 schrieb Ben Greear:
> The bug appears that vlan-tx-stripping is unconditionally enabled in
> at least my firmware. I have re-compiled w/out that flag set, and it
> appears
> to work for me.
>
> Please download this firmware, rename it firmware-2.bin, make sure you
> remove/rename
> any firmware-5.bin (etc) so mine will load, and see if that fixes your
> problem.
>
> Please note that it is very likely you will have to use same MAC address
> for the VLAN devices that the underlying station uses in order for
> this to work.
>
> https://www.candelatech.com/downloads/tmp/firmware-2-full-community.bin
>
>
> Thanks,
> Ben
>
>
> On 11/04/2016 02:50 PM, Ben Greear wrote:
>> I can reproduce this in my CT firmware. I'll see if I can fix it,
>> but for stock firmware, it might be that changing the driver to use
>> Ethernet packet type
>> of native-wifi would make .1q vlans work.
>>
>> Thanks,
>> Ben
>>
>> On 11/04/2016 10:28 AM, yu-chieh kung wrote:
>>> I met the same problem before,
>>> if i modify the 1q header to other value (0xaa00) before go into
>>> firmware.
>>> I can capture the packet in the air
>>> I think the vlan packet is dropped in firmware.
>>>
>>> 2016-11-04 22:41 GMT+08:00 Bruno Antunes <baantunes@gmail.com>:
>>>> On 4 November 2016 at 14:18, Mauro Mozzarelli
>>>> <openwrt@ezplanet.net> wrote:
>>>>> Since the capability is implemented in software you might be
>>>>> testing the
>>>>> limit of your router's CPU i/o speed.
>>>>
>>>> By loading the module in rawmode?
>>>>
>>>> The AP is an APU and Sta is an APU2.
>>>>
>>>>>
>>>>>
>>>>>
>>>>> On 04/11/16 14:13, Bruno Antunes wrote:
>>>>>>
>>>>>> Hi all,
>>>>>>
>>>>>> Old thread but I think the issue is still present.
>>>>>>
>>>>>> I'm running a setup with VLANs with WDS and ath10k cards.
>>>>>>
>>>>>> To make it work both cards must be loaded in rawmode, AP
>>>>>> and Sta, and with no security.
>>>>>>
>>>>>> I'm using a OpenWrt trunk r49941 and the most recent firmware,
>>>>>> 10.2.4.70.58, from Kalle ath10k firmware tree.
>>>>>>
>>>>>> Although it works the throughput is very bad.
>>>>>> Are there any alternatives to improve the throughput.
>>>>>>
>>>>>> Best Regards,
>>>>>> Bruno
>>>>>>
>>>>>> On 9 December 2015 at 17:24, voncken <cedric.voncken@acksys.fr>
>>>>>> wrote:
>>>>>>>
>>>>>>>
>>>>>>>> -----Message d'origine-----
>>>>>>>> De : Ben Greear [mailto:greearb@candelatech.com]
>>>>>>>> Envoyé : mercredi 9 décembre 2015 16:34
>>>>>>>> À : Cedric VONCKEN; ath10k@lists.infradead.org; linux-wireless
>>>>>>>> Objet : Re: ATH10K VLAN firmware issue
>>>>>>>>
>>>>>>>> This only happens when you use STA + WDS, or is .1q broken for
>>>>>>>> you in
>>>>>>>> other cases as well?
>>>>>>>
>>>>>>> No, this issue occurs in all modes (STA, STA + WDS, AP).
>>>>>>>
>>>>>>> Thanks
>>>>>>>
>>>>>>> Cedric.
>>>>>>>
>>>>>>>> Thanks,
>>>>>>>> Ben
>>>>>>>>
>>>>>>>> On 12/08/2015 06:29 AM, Cedric VONCKEN wrote:
>>>>>>>>>
>>>>>>>>> I'm testing to transmit frame with 802.1q tag (VLAN).
>>>>>>>>>
>>>>>>>>> My client is set in STA + WDS and the netdev is bridged
>>>>>>>>> with eth0.
>>>>>>>>> I have a computer with vlan configuration set connected
>>>>>>>>> to the STA
>>>>>>>>> eth0.
>>>>>>>>>
>>>>>>>>> If I try to transmit frames with 802.1q tag, the frames
>>>>>>>>> are not
>>>>>>>
>>>>>>> sent.
>>>>>>>>>
>>>>>>>>> I checked with wireless sniffer, and I don't see the
>>>>>>>>> frame with
>>>>>>>>> VLAN
>>>>>>>>> tag (the frames without VLAN tag are sent).
>>>>>>>>>
>>>>>>>>> I tested with firmware 10.2.4.70.14-2 from kale github,
>>>>>>>>> 10.1.467-ct-com-full-015 from candelatech and 10.2.4.70-2 from
>>>>>>>>> openwrt, and in all cases I have the same issue.
>>>>>>>>>
>>>>>>>>> Thanks for your help.
>>>>>>>>>
>>>>>>>>>
>>>>>>>>> --
>>>>>>>>> To unsubscribe from this list: send the line "unsubscribe
>>>>>>>>> linux-wireless" in the body of a message to
>>>>>>>>> majordomo@vger.kernel.org
>>>>>>>>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>>>>>>>>>
>>>>>>>> --
>>>>>>>> Ben Greear <greearb@candelatech.com>
>>>>>>>> Candela Technologies Inc http://www.candelatech.com
>>>>>>>
>>>>>>> --
>>>>>>> To unsubscribe from this list: send the line "unsubscribe
>>>>>>> linux-wireless"
>>>>>>> in
>>>>>>> the body of a message to majordomo@vger.kernel.org
>>>>>>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>>>>>>
>>>>>> _______________________________________________
>>>>>> openwrt-devel mailing list
>>>>>> openwrt-devel@lists.openwrt.org
>>>>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>>>>>
>>>>> _______________________________________________
>>>>> openwrt-devel mailing list
>>>>> openwrt-devel@lists.openwrt.org
>>>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>>>>
>>>> _______________________________________________
>>>> ath10k mailing list
>>>> ath10k@lists.infradead.org
>>>> http://lists.infradead.org/mailman/listinfo/ath10k
>>>
>>
>>
>
>
--
Mit freundlichen Grüssen / Regards
Sebastian Gottschall / CTO
NewMedia-NET GmbH - DD-WRT
Firmensitz: Berliner Ring 101, 64625 Bensheim
Registergericht: Amtsgericht Darmstadt, HRB 25473
Geschäftsführer: Peter Steinhäuser, Christian Scheele
http://www.dd-wrt.com
email: s.gottschall@dd-wrt.com
Tel.: +496251-582650 / Fax: +496251-5826565
^ permalink raw reply [flat|nested] 54+ messages in thread
* Re: [OpenWrt-Devel] ATH10K VLAN firmware issue
@ 2016-11-05 8:05 ` Sebastian Gottschall
0 siblings, 0 replies; 54+ messages in thread
From: Sebastian Gottschall @ 2016-11-05 8:05 UTC (permalink / raw)
To: Ben Greear, yu-chieh kung, Bruno Antunes
Cc: Mauro Mozzarelli, linux-wireless, OpenWrt Development List, ath10k
would be good if qca can fix this bug finally in all available
firmwares. its a very annoying issue since a long time
Sebastian
Am 04.11.2016 um 23:23 schrieb Ben Greear:
> The bug appears that vlan-tx-stripping is unconditionally enabled in
> at least my firmware. I have re-compiled w/out that flag set, and it
> appears
> to work for me.
>
> Please download this firmware, rename it firmware-2.bin, make sure you
> remove/rename
> any firmware-5.bin (etc) so mine will load, and see if that fixes your
> problem.
>
> Please note that it is very likely you will have to use same MAC address
> for the VLAN devices that the underlying station uses in order for
> this to work.
>
> https://www.candelatech.com/downloads/tmp/firmware-2-full-community.bin
>
>
> Thanks,
> Ben
>
>
> On 11/04/2016 02:50 PM, Ben Greear wrote:
>> I can reproduce this in my CT firmware. I'll see if I can fix it,
>> but for stock firmware, it might be that changing the driver to use
>> Ethernet packet type
>> of native-wifi would make .1q vlans work.
>>
>> Thanks,
>> Ben
>>
>> On 11/04/2016 10:28 AM, yu-chieh kung wrote:
>>> I met the same problem before,
>>> if i modify the 1q header to other value (0xaa00) before go into
>>> firmware.
>>> I can capture the packet in the air
>>> I think the vlan packet is dropped in firmware.
>>>
>>> 2016-11-04 22:41 GMT+08:00 Bruno Antunes <baantunes@gmail.com>:
>>>> On 4 November 2016 at 14:18, Mauro Mozzarelli
>>>> <openwrt@ezplanet.net> wrote:
>>>>> Since the capability is implemented in software you might be
>>>>> testing the
>>>>> limit of your router's CPU i/o speed.
>>>>
>>>> By loading the module in rawmode?
>>>>
>>>> The AP is an APU and Sta is an APU2.
>>>>
>>>>>
>>>>>
>>>>>
>>>>> On 04/11/16 14:13, Bruno Antunes wrote:
>>>>>>
>>>>>> Hi all,
>>>>>>
>>>>>> Old thread but I think the issue is still present.
>>>>>>
>>>>>> I'm running a setup with VLANs with WDS and ath10k cards.
>>>>>>
>>>>>> To make it work both cards must be loaded in rawmode, AP
>>>>>> and Sta, and with no security.
>>>>>>
>>>>>> I'm using a OpenWrt trunk r49941 and the most recent firmware,
>>>>>> 10.2.4.70.58, from Kalle ath10k firmware tree.
>>>>>>
>>>>>> Although it works the throughput is very bad.
>>>>>> Are there any alternatives to improve the throughput.
>>>>>>
>>>>>> Best Regards,
>>>>>> Bruno
>>>>>>
>>>>>> On 9 December 2015 at 17:24, voncken <cedric.voncken@acksys.fr>
>>>>>> wrote:
>>>>>>>
>>>>>>>
>>>>>>>> -----Message d'origine-----
>>>>>>>> De : Ben Greear [mailto:greearb@candelatech.com]
>>>>>>>> Envoyé : mercredi 9 décembre 2015 16:34
>>>>>>>> À : Cedric VONCKEN; ath10k@lists.infradead.org; linux-wireless
>>>>>>>> Objet : Re: ATH10K VLAN firmware issue
>>>>>>>>
>>>>>>>> This only happens when you use STA + WDS, or is .1q broken for
>>>>>>>> you in
>>>>>>>> other cases as well?
>>>>>>>
>>>>>>> No, this issue occurs in all modes (STA, STA + WDS, AP).
>>>>>>>
>>>>>>> Thanks
>>>>>>>
>>>>>>> Cedric.
>>>>>>>
>>>>>>>> Thanks,
>>>>>>>> Ben
>>>>>>>>
>>>>>>>> On 12/08/2015 06:29 AM, Cedric VONCKEN wrote:
>>>>>>>>>
>>>>>>>>> I'm testing to transmit frame with 802.1q tag (VLAN).
>>>>>>>>>
>>>>>>>>> My client is set in STA + WDS and the netdev is bridged
>>>>>>>>> with eth0.
>>>>>>>>> I have a computer with vlan configuration set connected
>>>>>>>>> to the STA
>>>>>>>>> eth0.
>>>>>>>>>
>>>>>>>>> If I try to transmit frames with 802.1q tag, the frames
>>>>>>>>> are not
>>>>>>>
>>>>>>> sent.
>>>>>>>>>
>>>>>>>>> I checked with wireless sniffer, and I don't see the
>>>>>>>>> frame with
>>>>>>>>> VLAN
>>>>>>>>> tag (the frames without VLAN tag are sent).
>>>>>>>>>
>>>>>>>>> I tested with firmware 10.2.4.70.14-2 from kale github,
>>>>>>>>> 10.1.467-ct-com-full-015 from candelatech and 10.2.4.70-2 from
>>>>>>>>> openwrt, and in all cases I have the same issue.
>>>>>>>>>
>>>>>>>>> Thanks for your help.
>>>>>>>>>
>>>>>>>>>
>>>>>>>>> --
>>>>>>>>> To unsubscribe from this list: send the line "unsubscribe
>>>>>>>>> linux-wireless" in the body of a message to
>>>>>>>>> majordomo@vger.kernel.org
>>>>>>>>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>>>>>>>>>
>>>>>>>> --
>>>>>>>> Ben Greear <greearb@candelatech.com>
>>>>>>>> Candela Technologies Inc http://www.candelatech.com
>>>>>>>
>>>>>>> --
>>>>>>> To unsubscribe from this list: send the line "unsubscribe
>>>>>>> linux-wireless"
>>>>>>> in
>>>>>>> the body of a message to majordomo@vger.kernel.org
>>>>>>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>>>>>>
>>>>>> _______________________________________________
>>>>>> openwrt-devel mailing list
>>>>>> openwrt-devel@lists.openwrt.org
>>>>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>>>>>
>>>>> _______________________________________________
>>>>> openwrt-devel mailing list
>>>>> openwrt-devel@lists.openwrt.org
>>>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>>>>
>>>> _______________________________________________
>>>> ath10k mailing list
>>>> ath10k@lists.infradead.org
>>>> http://lists.infradead.org/mailman/listinfo/ath10k
>>>
>>
>>
>
>
--
Mit freundlichen Grüssen / Regards
Sebastian Gottschall / CTO
NewMedia-NET GmbH - DD-WRT
Firmensitz: Berliner Ring 101, 64625 Bensheim
Registergericht: Amtsgericht Darmstadt, HRB 25473
Geschäftsführer: Peter Steinhäuser, Christian Scheele
http://www.dd-wrt.com
email: s.gottschall@dd-wrt.com
Tel.: +496251-582650 / Fax: +496251-5826565
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 54+ messages in thread
* Re: [OpenWrt-Devel] ATH10K VLAN firmware issue
2016-11-05 8:05 ` Sebastian Gottschall
@ 2016-11-05 14:35 ` Ben Greear
-1 siblings, 0 replies; 54+ messages in thread
From: Ben Greear @ 2016-11-05 14:35 UTC (permalink / raw)
To: Sebastian Gottschall, yu-chieh kung, Bruno Antunes
Cc: Mauro Mozzarelli, linux-wireless, OpenWrt Development List, ath10k
Looks to me like 10.4 defaults to the right value, but possibly there are other
issues with it. I tested my CT 10.4 and it worked OK with vlans for me.
Thanks,
Ben
On 11/05/2016 01:05 AM, Sebastian Gottschall wrote:
> would be good if qca can fix this bug finally in all available firmwares. its a very annoying issue since a long time
>
> Sebastian
>
>
> Am 04.11.2016 um 23:23 schrieb Ben Greear:
>> The bug appears that vlan-tx-stripping is unconditionally enabled in
>> at least my firmware. I have re-compiled w/out that flag set, and it appears
>> to work for me.
>>
>> Please download this firmware, rename it firmware-2.bin, make sure you remove/rename
>> any firmware-5.bin (etc) so mine will load, and see if that fixes your problem.
>>
>> Please note that it is very likely you will have to use same MAC address
>> for the VLAN devices that the underlying station uses in order for this to work.
>>
>> https://www.candelatech.com/downloads/tmp/firmware-2-full-community.bin
>>
>>
>> Thanks,
>> Ben
>>
>>
>> On 11/04/2016 02:50 PM, Ben Greear wrote:
>>> I can reproduce this in my CT firmware. I'll see if I can fix it,
>>> but for stock firmware, it might be that changing the driver to use Ethernet packet type
>>> of native-wifi would make .1q vlans work.
>>>
>>> Thanks,
>>> Ben
>>>
>>> On 11/04/2016 10:28 AM, yu-chieh kung wrote:
>>>> I met the same problem before,
>>>> if i modify the 1q header to other value (0xaa00) before go into firmware.
>>>> I can capture the packet in the air
>>>> I think the vlan packet is dropped in firmware.
>>>>
>>>> 2016-11-04 22:41 GMT+08:00 Bruno Antunes <baantunes@gmail.com>:
>>>>> On 4 November 2016 at 14:18, Mauro Mozzarelli <openwrt@ezplanet.net> wrote:
>>>>>> Since the capability is implemented in software you might be testing the
>>>>>> limit of your router's CPU i/o speed.
>>>>>
>>>>> By loading the module in rawmode?
>>>>>
>>>>> The AP is an APU and Sta is an APU2.
>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>> On 04/11/16 14:13, Bruno Antunes wrote:
>>>>>>>
>>>>>>> Hi all,
>>>>>>>
>>>>>>> Old thread but I think the issue is still present.
>>>>>>>
>>>>>>> I'm running a setup with VLANs with WDS and ath10k cards.
>>>>>>>
>>>>>>> To make it work both cards must be loaded in rawmode, AP
>>>>>>> and Sta, and with no security.
>>>>>>>
>>>>>>> I'm using a OpenWrt trunk r49941 and the most recent firmware,
>>>>>>> 10.2.4.70.58, from Kalle ath10k firmware tree.
>>>>>>>
>>>>>>> Although it works the throughput is very bad.
>>>>>>> Are there any alternatives to improve the throughput.
>>>>>>>
>>>>>>> Best Regards,
>>>>>>> Bruno
>>>>>>>
>>>>>>> On 9 December 2015 at 17:24, voncken <cedric.voncken@acksys.fr> wrote:
>>>>>>>>
>>>>>>>>
>>>>>>>>> -----Message d'origine-----
>>>>>>>>> De : Ben Greear [mailto:greearb@candelatech.com]
>>>>>>>>> Envoyé : mercredi 9 décembre 2015 16:34
>>>>>>>>> À : Cedric VONCKEN; ath10k@lists.infradead.org; linux-wireless
>>>>>>>>> Objet : Re: ATH10K VLAN firmware issue
>>>>>>>>>
>>>>>>>>> This only happens when you use STA + WDS, or is .1q broken for you in
>>>>>>>>> other cases as well?
>>>>>>>>
>>>>>>>> No, this issue occurs in all modes (STA, STA + WDS, AP).
>>>>>>>>
>>>>>>>> Thanks
>>>>>>>>
>>>>>>>> Cedric.
>>>>>>>>
>>>>>>>>> Thanks,
>>>>>>>>> Ben
>>>>>>>>>
>>>>>>>>> On 12/08/2015 06:29 AM, Cedric VONCKEN wrote:
>>>>>>>>>>
>>>>>>>>>> I'm testing to transmit frame with 802.1q tag (VLAN).
>>>>>>>>>>
>>>>>>>>>> My client is set in STA + WDS and the netdev is bridged with eth0.
>>>>>>>>>> I have a computer with vlan configuration set connected to the STA
>>>>>>>>>> eth0.
>>>>>>>>>>
>>>>>>>>>> If I try to transmit frames with 802.1q tag, the frames are not
>>>>>>>>
>>>>>>>> sent.
>>>>>>>>>>
>>>>>>>>>> I checked with wireless sniffer, and I don't see the frame with
>>>>>>>>>> VLAN
>>>>>>>>>> tag (the frames without VLAN tag are sent).
>>>>>>>>>>
>>>>>>>>>> I tested with firmware 10.2.4.70.14-2 from kale github,
>>>>>>>>>> 10.1.467-ct-com-full-015 from candelatech and 10.2.4.70-2 from
>>>>>>>>>> openwrt, and in all cases I have the same issue.
>>>>>>>>>>
>>>>>>>>>> Thanks for your help.
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>> --
>>>>>>>>>> To unsubscribe from this list: send the line "unsubscribe
>>>>>>>>>> linux-wireless" in the body of a message to majordomo@vger.kernel.org
>>>>>>>>>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>>>>>>>>>>
>>>>>>>>> --
>>>>>>>>> Ben Greear <greearb@candelatech.com>
>>>>>>>>> Candela Technologies Inc http://www.candelatech.com
>>>>>>>>
>>>>>>>> --
>>>>>>>> To unsubscribe from this list: send the line "unsubscribe linux-wireless"
>>>>>>>> in
>>>>>>>> the body of a message to majordomo@vger.kernel.org
>>>>>>>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>>>>>>>
>>>>>>> _______________________________________________
>>>>>>> openwrt-devel mailing list
>>>>>>> openwrt-devel@lists.openwrt.org
>>>>>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>>>>>>
>>>>>> _______________________________________________
>>>>>> openwrt-devel mailing list
>>>>>> openwrt-devel@lists.openwrt.org
>>>>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>>>>>
>>>>> _______________________________________________
>>>>> ath10k mailing list
>>>>> ath10k@lists.infradead.org
>>>>> http://lists.infradead.org/mailman/listinfo/ath10k
>>>>
>>>
>>>
>>
>>
>
>
--
Ben Greear <greearb@candelatech.com>
Candela Technologies Inc http://www.candelatech.com
^ permalink raw reply [flat|nested] 54+ messages in thread
* Re: [OpenWrt-Devel] ATH10K VLAN firmware issue
@ 2016-11-05 14:35 ` Ben Greear
0 siblings, 0 replies; 54+ messages in thread
From: Ben Greear @ 2016-11-05 14:35 UTC (permalink / raw)
To: Sebastian Gottschall, yu-chieh kung, Bruno Antunes
Cc: Mauro Mozzarelli, linux-wireless, OpenWrt Development List, ath10k
Looks to me like 10.4 defaults to the right value, but possibly there are other
issues with it. I tested my CT 10.4 and it worked OK with vlans for me.
Thanks,
Ben
On 11/05/2016 01:05 AM, Sebastian Gottschall wrote:
> would be good if qca can fix this bug finally in all available firmwares. its a very annoying issue since a long time
>
> Sebastian
>
>
> Am 04.11.2016 um 23:23 schrieb Ben Greear:
>> The bug appears that vlan-tx-stripping is unconditionally enabled in
>> at least my firmware. I have re-compiled w/out that flag set, and it appears
>> to work for me.
>>
>> Please download this firmware, rename it firmware-2.bin, make sure you remove/rename
>> any firmware-5.bin (etc) so mine will load, and see if that fixes your problem.
>>
>> Please note that it is very likely you will have to use same MAC address
>> for the VLAN devices that the underlying station uses in order for this to work.
>>
>> https://www.candelatech.com/downloads/tmp/firmware-2-full-community.bin
>>
>>
>> Thanks,
>> Ben
>>
>>
>> On 11/04/2016 02:50 PM, Ben Greear wrote:
>>> I can reproduce this in my CT firmware. I'll see if I can fix it,
>>> but for stock firmware, it might be that changing the driver to use Ethernet packet type
>>> of native-wifi would make .1q vlans work.
>>>
>>> Thanks,
>>> Ben
>>>
>>> On 11/04/2016 10:28 AM, yu-chieh kung wrote:
>>>> I met the same problem before,
>>>> if i modify the 1q header to other value (0xaa00) before go into firmware.
>>>> I can capture the packet in the air
>>>> I think the vlan packet is dropped in firmware.
>>>>
>>>> 2016-11-04 22:41 GMT+08:00 Bruno Antunes <baantunes@gmail.com>:
>>>>> On 4 November 2016 at 14:18, Mauro Mozzarelli <openwrt@ezplanet.net> wrote:
>>>>>> Since the capability is implemented in software you might be testing the
>>>>>> limit of your router's CPU i/o speed.
>>>>>
>>>>> By loading the module in rawmode?
>>>>>
>>>>> The AP is an APU and Sta is an APU2.
>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>> On 04/11/16 14:13, Bruno Antunes wrote:
>>>>>>>
>>>>>>> Hi all,
>>>>>>>
>>>>>>> Old thread but I think the issue is still present.
>>>>>>>
>>>>>>> I'm running a setup with VLANs with WDS and ath10k cards.
>>>>>>>
>>>>>>> To make it work both cards must be loaded in rawmode, AP
>>>>>>> and Sta, and with no security.
>>>>>>>
>>>>>>> I'm using a OpenWrt trunk r49941 and the most recent firmware,
>>>>>>> 10.2.4.70.58, from Kalle ath10k firmware tree.
>>>>>>>
>>>>>>> Although it works the throughput is very bad.
>>>>>>> Are there any alternatives to improve the throughput.
>>>>>>>
>>>>>>> Best Regards,
>>>>>>> Bruno
>>>>>>>
>>>>>>> On 9 December 2015 at 17:24, voncken <cedric.voncken@acksys.fr> wrote:
>>>>>>>>
>>>>>>>>
>>>>>>>>> -----Message d'origine-----
>>>>>>>>> De : Ben Greear [mailto:greearb@candelatech.com]
>>>>>>>>> Envoyé : mercredi 9 décembre 2015 16:34
>>>>>>>>> À : Cedric VONCKEN; ath10k@lists.infradead.org; linux-wireless
>>>>>>>>> Objet : Re: ATH10K VLAN firmware issue
>>>>>>>>>
>>>>>>>>> This only happens when you use STA + WDS, or is .1q broken for you in
>>>>>>>>> other cases as well?
>>>>>>>>
>>>>>>>> No, this issue occurs in all modes (STA, STA + WDS, AP).
>>>>>>>>
>>>>>>>> Thanks
>>>>>>>>
>>>>>>>> Cedric.
>>>>>>>>
>>>>>>>>> Thanks,
>>>>>>>>> Ben
>>>>>>>>>
>>>>>>>>> On 12/08/2015 06:29 AM, Cedric VONCKEN wrote:
>>>>>>>>>>
>>>>>>>>>> I'm testing to transmit frame with 802.1q tag (VLAN).
>>>>>>>>>>
>>>>>>>>>> My client is set in STA + WDS and the netdev is bridged with eth0.
>>>>>>>>>> I have a computer with vlan configuration set connected to the STA
>>>>>>>>>> eth0.
>>>>>>>>>>
>>>>>>>>>> If I try to transmit frames with 802.1q tag, the frames are not
>>>>>>>>
>>>>>>>> sent.
>>>>>>>>>>
>>>>>>>>>> I checked with wireless sniffer, and I don't see the frame with
>>>>>>>>>> VLAN
>>>>>>>>>> tag (the frames without VLAN tag are sent).
>>>>>>>>>>
>>>>>>>>>> I tested with firmware 10.2.4.70.14-2 from kale github,
>>>>>>>>>> 10.1.467-ct-com-full-015 from candelatech and 10.2.4.70-2 from
>>>>>>>>>> openwrt, and in all cases I have the same issue.
>>>>>>>>>>
>>>>>>>>>> Thanks for your help.
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>> --
>>>>>>>>>> To unsubscribe from this list: send the line "unsubscribe
>>>>>>>>>> linux-wireless" in the body of a message to majordomo@vger.kernel.org
>>>>>>>>>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>>>>>>>>>>
>>>>>>>>> --
>>>>>>>>> Ben Greear <greearb@candelatech.com>
>>>>>>>>> Candela Technologies Inc http://www.candelatech.com
>>>>>>>>
>>>>>>>> --
>>>>>>>> To unsubscribe from this list: send the line "unsubscribe linux-wireless"
>>>>>>>> in
>>>>>>>> the body of a message to majordomo@vger.kernel.org
>>>>>>>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>>>>>>>
>>>>>>> _______________________________________________
>>>>>>> openwrt-devel mailing list
>>>>>>> openwrt-devel@lists.openwrt.org
>>>>>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>>>>>>
>>>>>> _______________________________________________
>>>>>> openwrt-devel mailing list
>>>>>> openwrt-devel@lists.openwrt.org
>>>>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>>>>>
>>>>> _______________________________________________
>>>>> ath10k mailing list
>>>>> ath10k@lists.infradead.org
>>>>> http://lists.infradead.org/mailman/listinfo/ath10k
>>>>
>>>
>>>
>>
>>
>
>
--
Ben Greear <greearb@candelatech.com>
Candela Technologies Inc http://www.candelatech.com
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 54+ messages in thread
* RE: [OpenWrt-Devel] ATH10K VLAN firmware issue
2016-11-05 14:35 ` Ben Greear
@ 2016-11-15 14:37 ` voncken
-1 siblings, 0 replies; 54+ messages in thread
From: voncken @ 2016-11-15 14:37 UTC (permalink / raw)
To: 'Ben Greear'
Cc: linux-wireless, 'OpenWrt Development List', ath10k
Hi Ben,
Do you plan to release a candelatech firmware with this fix?
Regards.
Cedric Voncken.
> -----Message d'origine-----
> De : linux-wireless-owner@vger.kernel.org [mailto:linux-wireless-
> owner@vger.kernel.org] De la part de Ben Greear
> Envoyé : samedi 5 novembre 2016 15:35
> À : Sebastian Gottschall; yu-chieh kung; Bruno Antunes
> Cc : Mauro Mozzarelli; linux-wireless@vger.kernel.org; OpenWrt
> Development List; ath10k@lists.infradead.org
> Objet : Re: [OpenWrt-Devel] ATH10K VLAN firmware issue
>
> Looks to me like 10.4 defaults to the right value, but possibly there
> are other issues with it. I tested my CT 10.4 and it worked OK with
> vlans for me.
>
> Thanks,
> Ben
>
> On 11/05/2016 01:05 AM, Sebastian Gottschall wrote:
> > would be good if qca can fix this bug finally in all available
> > firmwares. its a very annoying issue since a long time
> >
> > Sebastian
> >
> >
> > Am 04.11.2016 um 23:23 schrieb Ben Greear:
> >> The bug appears that vlan-tx-stripping is unconditionally enabled in
> >> at least my firmware. I have re-compiled w/out that flag set, and
> it
> >> appears to work for me.
> >>
> >> Please download this firmware, rename it firmware-2.bin, make sure
> >> you remove/rename any firmware-5.bin (etc) so mine will load, and
> see if that fixes your problem.
> >>
> >> Please note that it is very likely you will have to use same MAC
> >> address for the VLAN devices that the underlying station uses in
> order for this to work.
> >>
> >> https://www.candelatech.com/downloads/tmp/firmware-2-full-
> community.b
> >> in
> >>
> >>
> >> Thanks,
> >> Ben
> >>
> >>
> >> On 11/04/2016 02:50 PM, Ben Greear wrote:
> >>> I can reproduce this in my CT firmware. I'll see if I can fix it,
> >>> but for stock firmware, it might be that changing the driver to use
> >>> Ethernet packet type of native-wifi would make .1q vlans work.
> >>>
> >>> Thanks,
> >>> Ben
> >>>
> >>> On 11/04/2016 10:28 AM, yu-chieh kung wrote:
> >>>> I met the same problem before,
> >>>> if i modify the 1q header to other value (0xaa00) before go into
> firmware.
> >>>> I can capture the packet in the air I think the vlan packet is
> >>>> dropped in firmware.
> >>>>
> >>>> 2016-11-04 22:41 GMT+08:00 Bruno Antunes <baantunes@gmail.com>:
> >>>>> On 4 November 2016 at 14:18, Mauro Mozzarelli
> <openwrt@ezplanet.net> wrote:
> >>>>>> Since the capability is implemented in software you might be
> >>>>>> testing the limit of your router's CPU i/o speed.
> >>>>>
> >>>>> By loading the module in rawmode?
> >>>>>
> >>>>> The AP is an APU and Sta is an APU2.
> >>>>>
> >>>>>>
> >>>>>>
> >>>>>>
> >>>>>> On 04/11/16 14:13, Bruno Antunes wrote:
> >>>>>>>
> >>>>>>> Hi all,
> >>>>>>>
> >>>>>>> Old thread but I think the issue is still present.
> >>>>>>>
> >>>>>>> I'm running a setup with VLANs with WDS and ath10k cards.
> >>>>>>>
> >>>>>>> To make it work both cards must be loaded in rawmode, AP and
> >>>>>>> Sta, and with no security.
> >>>>>>>
> >>>>>>> I'm using a OpenWrt trunk r49941 and the most recent firmware,
> >>>>>>> 10.2.4.70.58, from Kalle ath10k firmware tree.
> >>>>>>>
> >>>>>>> Although it works the throughput is very bad.
> >>>>>>> Are there any alternatives to improve the throughput.
> >>>>>>>
> >>>>>>> Best Regards,
> >>>>>>> Bruno
> >>>>>>>
> >>>>>>> On 9 December 2015 at 17:24, voncken <cedric.voncken@acksys.fr>
> wrote:
> >>>>>>>>
> >>>>>>>>
> >>>>>>>>> -----Message d'origine-----
> >>>>>>>>> De : Ben Greear [mailto:greearb@candelatech.com] Envoyé :
> >>>>>>>>> mercredi 9 décembre 2015 16:34 À : Cedric VONCKEN;
> >>>>>>>>> ath10k@lists.infradead.org; linux-wireless Objet : Re: ATH10K
> >>>>>>>>> VLAN firmware issue
> >>>>>>>>>
> >>>>>>>>> This only happens when you use STA + WDS, or is .1q broken
> >>>>>>>>> for you in other cases as well?
> >>>>>>>>
> >>>>>>>> No, this issue occurs in all modes (STA, STA + WDS, AP).
> >>>>>>>>
> >>>>>>>> Thanks
> >>>>>>>>
> >>>>>>>> Cedric.
> >>>>>>>>
> >>>>>>>>> Thanks,
> >>>>>>>>> Ben
> >>>>>>>>>
> >>>>>>>>> On 12/08/2015 06:29 AM, Cedric VONCKEN wrote:
> >>>>>>>>>>
> >>>>>>>>>> I'm testing to transmit frame with 802.1q tag (VLAN).
> >>>>>>>>>>
> >>>>>>>>>> My client is set in STA + WDS and the netdev is bridged
> with eth0.
> >>>>>>>>>> I have a computer with vlan configuration set connected
> >>>>>>>>>> to the STA eth0.
> >>>>>>>>>>
> >>>>>>>>>> If I try to transmit frames with 802.1q tag, the frames
> >>>>>>>>>> are not
> >>>>>>>>
> >>>>>>>> sent.
> >>>>>>>>>>
> >>>>>>>>>> I checked with wireless sniffer, and I don't see the
> >>>>>>>>>> frame with VLAN tag (the frames without VLAN tag are sent).
> >>>>>>>>>>
> >>>>>>>>>> I tested with firmware 10.2.4.70.14-2 from kale github,
> >>>>>>>>>> 10.1.467-ct-com-full-015 from candelatech and 10.2.4.70-2
> >>>>>>>>>> from openwrt, and in all cases I have the same issue.
> >>>>>>>>>>
> >>>>>>>>>> Thanks for your help.
> >>>>>>>>>>
> >>>>>>>>>>
> >>>>>>>>>> --
> >>>>>>>>>> To unsubscribe from this list: send the line "unsubscribe
> >>>>>>>>>> linux-wireless" in the body of a message to
> >>>>>>>>>> majordomo@vger.kernel.org More majordomo info at
> >>>>>>>>>> http://vger.kernel.org/majordomo-info.html
> >>>>>>>>>>
> >>>>>>>>> --
> >>>>>>>>> Ben Greear <greearb@candelatech.com> Candela Technologies Inc
> >>>>>>>>> http://www.candelatech.com
> >>>>>>>>
> >>>>>>>> --
> >>>>>>>> To unsubscribe from this list: send the line "unsubscribe
> linux-wireless"
> >>>>>>>> in
> >>>>>>>> the body of a message to majordomo@vger.kernel.org More
> >>>>>>>> majordomo info at http://vger.kernel.org/majordomo-info.html
> >>>>>>>
> >>>>>>> _______________________________________________
> >>>>>>> openwrt-devel mailing list
> >>>>>>> openwrt-devel@lists.openwrt.org
> >>>>>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-
> devel
> >>>>>>
> >>>>>> _______________________________________________
> >>>>>> openwrt-devel mailing list
> >>>>>> openwrt-devel@lists.openwrt.org
> >>>>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
> >>>>>
> >>>>> _______________________________________________
> >>>>> ath10k mailing list
> >>>>> ath10k@lists.infradead.org
> >>>>> http://lists.infradead.org/mailman/listinfo/ath10k
> >>>>
> >>>
> >>>
> >>
> >>
> >
> >
>
> --
> Ben Greear <greearb@candelatech.com>
> Candela Technologies Inc http://www.candelatech.com
^ permalink raw reply [flat|nested] 54+ messages in thread
* RE: [OpenWrt-Devel] ATH10K VLAN firmware issue
@ 2016-11-15 14:37 ` voncken
0 siblings, 0 replies; 54+ messages in thread
From: voncken @ 2016-11-15 14:37 UTC (permalink / raw)
To: 'Ben Greear'
Cc: 'OpenWrt Development List', linux-wireless, ath10k
Hi Ben,
Do you plan to release a candelatech firmware with this fix?
Regards.
Cedric Voncken.
> -----Message d'origine-----
> De : linux-wireless-owner@vger.kernel.org [mailto:linux-wireless-
> owner@vger.kernel.org] De la part de Ben Greear
> Envoyé : samedi 5 novembre 2016 15:35
> À : Sebastian Gottschall; yu-chieh kung; Bruno Antunes
> Cc : Mauro Mozzarelli; linux-wireless@vger.kernel.org; OpenWrt
> Development List; ath10k@lists.infradead.org
> Objet : Re: [OpenWrt-Devel] ATH10K VLAN firmware issue
>
> Looks to me like 10.4 defaults to the right value, but possibly there
> are other issues with it. I tested my CT 10.4 and it worked OK with
> vlans for me.
>
> Thanks,
> Ben
>
> On 11/05/2016 01:05 AM, Sebastian Gottschall wrote:
> > would be good if qca can fix this bug finally in all available
> > firmwares. its a very annoying issue since a long time
> >
> > Sebastian
> >
> >
> > Am 04.11.2016 um 23:23 schrieb Ben Greear:
> >> The bug appears that vlan-tx-stripping is unconditionally enabled in
> >> at least my firmware. I have re-compiled w/out that flag set, and
> it
> >> appears to work for me.
> >>
> >> Please download this firmware, rename it firmware-2.bin, make sure
> >> you remove/rename any firmware-5.bin (etc) so mine will load, and
> see if that fixes your problem.
> >>
> >> Please note that it is very likely you will have to use same MAC
> >> address for the VLAN devices that the underlying station uses in
> order for this to work.
> >>
> >> https://www.candelatech.com/downloads/tmp/firmware-2-full-
> community.b
> >> in
> >>
> >>
> >> Thanks,
> >> Ben
> >>
> >>
> >> On 11/04/2016 02:50 PM, Ben Greear wrote:
> >>> I can reproduce this in my CT firmware. I'll see if I can fix it,
> >>> but for stock firmware, it might be that changing the driver to use
> >>> Ethernet packet type of native-wifi would make .1q vlans work.
> >>>
> >>> Thanks,
> >>> Ben
> >>>
> >>> On 11/04/2016 10:28 AM, yu-chieh kung wrote:
> >>>> I met the same problem before,
> >>>> if i modify the 1q header to other value (0xaa00) before go into
> firmware.
> >>>> I can capture the packet in the air I think the vlan packet is
> >>>> dropped in firmware.
> >>>>
> >>>> 2016-11-04 22:41 GMT+08:00 Bruno Antunes <baantunes@gmail.com>:
> >>>>> On 4 November 2016 at 14:18, Mauro Mozzarelli
> <openwrt@ezplanet.net> wrote:
> >>>>>> Since the capability is implemented in software you might be
> >>>>>> testing the limit of your router's CPU i/o speed.
> >>>>>
> >>>>> By loading the module in rawmode?
> >>>>>
> >>>>> The AP is an APU and Sta is an APU2.
> >>>>>
> >>>>>>
> >>>>>>
> >>>>>>
> >>>>>> On 04/11/16 14:13, Bruno Antunes wrote:
> >>>>>>>
> >>>>>>> Hi all,
> >>>>>>>
> >>>>>>> Old thread but I think the issue is still present.
> >>>>>>>
> >>>>>>> I'm running a setup with VLANs with WDS and ath10k cards.
> >>>>>>>
> >>>>>>> To make it work both cards must be loaded in rawmode, AP and
> >>>>>>> Sta, and with no security.
> >>>>>>>
> >>>>>>> I'm using a OpenWrt trunk r49941 and the most recent firmware,
> >>>>>>> 10.2.4.70.58, from Kalle ath10k firmware tree.
> >>>>>>>
> >>>>>>> Although it works the throughput is very bad.
> >>>>>>> Are there any alternatives to improve the throughput.
> >>>>>>>
> >>>>>>> Best Regards,
> >>>>>>> Bruno
> >>>>>>>
> >>>>>>> On 9 December 2015 at 17:24, voncken <cedric.voncken@acksys.fr>
> wrote:
> >>>>>>>>
> >>>>>>>>
> >>>>>>>>> -----Message d'origine-----
> >>>>>>>>> De : Ben Greear [mailto:greearb@candelatech.com] Envoyé :
> >>>>>>>>> mercredi 9 décembre 2015 16:34 À : Cedric VONCKEN;
> >>>>>>>>> ath10k@lists.infradead.org; linux-wireless Objet : Re: ATH10K
> >>>>>>>>> VLAN firmware issue
> >>>>>>>>>
> >>>>>>>>> This only happens when you use STA + WDS, or is .1q broken
> >>>>>>>>> for you in other cases as well?
> >>>>>>>>
> >>>>>>>> No, this issue occurs in all modes (STA, STA + WDS, AP).
> >>>>>>>>
> >>>>>>>> Thanks
> >>>>>>>>
> >>>>>>>> Cedric.
> >>>>>>>>
> >>>>>>>>> Thanks,
> >>>>>>>>> Ben
> >>>>>>>>>
> >>>>>>>>> On 12/08/2015 06:29 AM, Cedric VONCKEN wrote:
> >>>>>>>>>>
> >>>>>>>>>> I'm testing to transmit frame with 802.1q tag (VLAN).
> >>>>>>>>>>
> >>>>>>>>>> My client is set in STA + WDS and the netdev is bridged
> with eth0.
> >>>>>>>>>> I have a computer with vlan configuration set connected
> >>>>>>>>>> to the STA eth0.
> >>>>>>>>>>
> >>>>>>>>>> If I try to transmit frames with 802.1q tag, the frames
> >>>>>>>>>> are not
> >>>>>>>>
> >>>>>>>> sent.
> >>>>>>>>>>
> >>>>>>>>>> I checked with wireless sniffer, and I don't see the
> >>>>>>>>>> frame with VLAN tag (the frames without VLAN tag are sent).
> >>>>>>>>>>
> >>>>>>>>>> I tested with firmware 10.2.4.70.14-2 from kale github,
> >>>>>>>>>> 10.1.467-ct-com-full-015 from candelatech and 10.2.4.70-2
> >>>>>>>>>> from openwrt, and in all cases I have the same issue.
> >>>>>>>>>>
> >>>>>>>>>> Thanks for your help.
> >>>>>>>>>>
> >>>>>>>>>>
> >>>>>>>>>> --
> >>>>>>>>>> To unsubscribe from this list: send the line "unsubscribe
> >>>>>>>>>> linux-wireless" in the body of a message to
> >>>>>>>>>> majordomo@vger.kernel.org More majordomo info at
> >>>>>>>>>> http://vger.kernel.org/majordomo-info.html
> >>>>>>>>>>
> >>>>>>>>> --
> >>>>>>>>> Ben Greear <greearb@candelatech.com> Candela Technologies Inc
> >>>>>>>>> http://www.candelatech.com
> >>>>>>>>
> >>>>>>>> --
> >>>>>>>> To unsubscribe from this list: send the line "unsubscribe
> linux-wireless"
> >>>>>>>> in
> >>>>>>>> the body of a message to majordomo@vger.kernel.org More
> >>>>>>>> majordomo info at http://vger.kernel.org/majordomo-info.html
> >>>>>>>
> >>>>>>> _______________________________________________
> >>>>>>> openwrt-devel mailing list
> >>>>>>> openwrt-devel@lists.openwrt.org
> >>>>>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-
> devel
> >>>>>>
> >>>>>> _______________________________________________
> >>>>>> openwrt-devel mailing list
> >>>>>> openwrt-devel@lists.openwrt.org
> >>>>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
> >>>>>
> >>>>> _______________________________________________
> >>>>> ath10k mailing list
> >>>>> ath10k@lists.infradead.org
> >>>>> http://lists.infradead.org/mailman/listinfo/ath10k
> >>>>
> >>>
> >>>
> >>
> >>
> >
> >
>
> --
> Ben Greear <greearb@candelatech.com>
> Candela Technologies Inc http://www.candelatech.com
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 54+ messages in thread
* Re: [OpenWrt-Devel] ATH10K VLAN firmware issue
2016-11-15 14:37 ` voncken
@ 2016-11-15 14:55 ` Ben Greear
-1 siblings, 0 replies; 54+ messages in thread
From: Ben Greear @ 2016-11-15 14:55 UTC (permalink / raw)
To: voncken; +Cc: linux-wireless, 'OpenWrt Development List', ath10k
The beta-18 release on my web page has the fix and should work fine.
Probably soon I will promote the beta-18 to final release
status. Any help in testing and verifying the beta works well
is welcome.
Thanks,
Ben
On 11/15/2016 06:37 AM, voncken wrote:
> Hi Ben,
>
> Do you plan to release a candelatech firmware with this fix?
>
> Regards.
>
> Cedric Voncken.
>> -----Message d'origine-----
>> De : linux-wireless-owner@vger.kernel.org [mailto:linux-wireless-
>> owner@vger.kernel.org] De la part de Ben Greear
>> Envoyé : samedi 5 novembre 2016 15:35
>> À : Sebastian Gottschall; yu-chieh kung; Bruno Antunes
>> Cc : Mauro Mozzarelli; linux-wireless@vger.kernel.org; OpenWrt
>> Development List; ath10k@lists.infradead.org
>> Objet : Re: [OpenWrt-Devel] ATH10K VLAN firmware issue
>>
>> Looks to me like 10.4 defaults to the right value, but possibly there
>> are other issues with it. I tested my CT 10.4 and it worked OK with
>> vlans for me.
>>
>> Thanks,
>> Ben
>>
>> On 11/05/2016 01:05 AM, Sebastian Gottschall wrote:
>>> would be good if qca can fix this bug finally in all available
>>> firmwares. its a very annoying issue since a long time
>>>
>>> Sebastian
>>>
>>>
>>> Am 04.11.2016 um 23:23 schrieb Ben Greear:
>>>> The bug appears that vlan-tx-stripping is unconditionally enabled in
>>>> at least my firmware. I have re-compiled w/out that flag set, and
>> it
>>>> appears to work for me.
>>>>
>>>> Please download this firmware, rename it firmware-2.bin, make sure
>>>> you remove/rename any firmware-5.bin (etc) so mine will load, and
>> see if that fixes your problem.
>>>>
>>>> Please note that it is very likely you will have to use same MAC
>>>> address for the VLAN devices that the underlying station uses in
>> order for this to work.
>>>>
>>>> https://www.candelatech.com/downloads/tmp/firmware-2-full-
>> community.b
>>>> in
>>>>
>>>>
>>>> Thanks,
>>>> Ben
>>>>
>>>>
>>>> On 11/04/2016 02:50 PM, Ben Greear wrote:
>>>>> I can reproduce this in my CT firmware. I'll see if I can fix it,
>>>>> but for stock firmware, it might be that changing the driver to use
>>>>> Ethernet packet type of native-wifi would make .1q vlans work.
>>>>>
>>>>> Thanks,
>>>>> Ben
>>>>>
>>>>> On 11/04/2016 10:28 AM, yu-chieh kung wrote:
>>>>>> I met the same problem before,
>>>>>> if i modify the 1q header to other value (0xaa00) before go into
>> firmware.
>>>>>> I can capture the packet in the air I think the vlan packet is
>>>>>> dropped in firmware.
>>>>>>
>>>>>> 2016-11-04 22:41 GMT+08:00 Bruno Antunes <baantunes@gmail.com>:
>>>>>>> On 4 November 2016 at 14:18, Mauro Mozzarelli
>> <openwrt@ezplanet.net> wrote:
>>>>>>>> Since the capability is implemented in software you might be
>>>>>>>> testing the limit of your router's CPU i/o speed.
>>>>>>>
>>>>>>> By loading the module in rawmode?
>>>>>>>
>>>>>>> The AP is an APU and Sta is an APU2.
>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>> On 04/11/16 14:13, Bruno Antunes wrote:
>>>>>>>>>
>>>>>>>>> Hi all,
>>>>>>>>>
>>>>>>>>> Old thread but I think the issue is still present.
>>>>>>>>>
>>>>>>>>> I'm running a setup with VLANs with WDS and ath10k cards.
>>>>>>>>>
>>>>>>>>> To make it work both cards must be loaded in rawmode, AP and
>>>>>>>>> Sta, and with no security.
>>>>>>>>>
>>>>>>>>> I'm using a OpenWrt trunk r49941 and the most recent firmware,
>>>>>>>>> 10.2.4.70.58, from Kalle ath10k firmware tree.
>>>>>>>>>
>>>>>>>>> Although it works the throughput is very bad.
>>>>>>>>> Are there any alternatives to improve the throughput.
>>>>>>>>>
>>>>>>>>> Best Regards,
>>>>>>>>> Bruno
>>>>>>>>>
>>>>>>>>> On 9 December 2015 at 17:24, voncken <cedric.voncken@acksys.fr>
>> wrote:
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>> -----Message d'origine-----
>>>>>>>>>>> De : Ben Greear [mailto:greearb@candelatech.com] Envoyé :
>>>>>>>>>>> mercredi 9 décembre 2015 16:34 À : Cedric VONCKEN;
>>>>>>>>>>> ath10k@lists.infradead.org; linux-wireless Objet : Re: ATH10K
>>>>>>>>>>> VLAN firmware issue
>>>>>>>>>>>
>>>>>>>>>>> This only happens when you use STA + WDS, or is .1q broken
>>>>>>>>>>> for you in other cases as well?
>>>>>>>>>>
>>>>>>>>>> No, this issue occurs in all modes (STA, STA + WDS, AP).
>>>>>>>>>>
>>>>>>>>>> Thanks
>>>>>>>>>>
>>>>>>>>>> Cedric.
>>>>>>>>>>
>>>>>>>>>>> Thanks,
>>>>>>>>>>> Ben
>>>>>>>>>>>
>>>>>>>>>>> On 12/08/2015 06:29 AM, Cedric VONCKEN wrote:
>>>>>>>>>>>>
>>>>>>>>>>>> I'm testing to transmit frame with 802.1q tag (VLAN).
>>>>>>>>>>>>
>>>>>>>>>>>> My client is set in STA + WDS and the netdev is bridged
>> with eth0.
>>>>>>>>>>>> I have a computer with vlan configuration set connected
>>>>>>>>>>>> to the STA eth0.
>>>>>>>>>>>>
>>>>>>>>>>>> If I try to transmit frames with 802.1q tag, the frames
>>>>>>>>>>>> are not
>>>>>>>>>>
>>>>>>>>>> sent.
>>>>>>>>>>>>
>>>>>>>>>>>> I checked with wireless sniffer, and I don't see the
>>>>>>>>>>>> frame with VLAN tag (the frames without VLAN tag are sent).
>>>>>>>>>>>>
>>>>>>>>>>>> I tested with firmware 10.2.4.70.14-2 from kale github,
>>>>>>>>>>>> 10.1.467-ct-com-full-015 from candelatech and 10.2.4.70-2
>>>>>>>>>>>> from openwrt, and in all cases I have the same issue.
>>>>>>>>>>>>
>>>>>>>>>>>> Thanks for your help.
>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>> --
>>>>>>>>>>>> To unsubscribe from this list: send the line "unsubscribe
>>>>>>>>>>>> linux-wireless" in the body of a message to
>>>>>>>>>>>> majordomo@vger.kernel.org More majordomo info at
>>>>>>>>>>>> http://vger.kernel.org/majordomo-info.html
>>>>>>>>>>>>
>>>>>>>>>>> --
>>>>>>>>>>> Ben Greear <greearb@candelatech.com> Candela Technologies Inc
>>>>>>>>>>> http://www.candelatech.com
>>>>>>>>>>
>>>>>>>>>> --
>>>>>>>>>> To unsubscribe from this list: send the line "unsubscribe
>> linux-wireless"
>>>>>>>>>> in
>>>>>>>>>> the body of a message to majordomo@vger.kernel.org More
>>>>>>>>>> majordomo info at http://vger.kernel.org/majordomo-info.html
>>>>>>>>>
>>>>>>>>> _______________________________________________
>>>>>>>>> openwrt-devel mailing list
>>>>>>>>> openwrt-devel@lists.openwrt.org
>>>>>>>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-
>> devel
>>>>>>>>
>>>>>>>> _______________________________________________
>>>>>>>> openwrt-devel mailing list
>>>>>>>> openwrt-devel@lists.openwrt.org
>>>>>>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>>>>>>>
>>>>>>> _______________________________________________
>>>>>>> ath10k mailing list
>>>>>>> ath10k@lists.infradead.org
>>>>>>> http://lists.infradead.org/mailman/listinfo/ath10k
>>>>>>
>>>>>
>>>>>
>>>>
>>>>
>>>
>>>
>>
>> --
>> Ben Greear <greearb@candelatech.com>
>> Candela Technologies Inc http://www.candelatech.com
>
--
Ben Greear <greearb@candelatech.com>
Candela Technologies Inc http://www.candelatech.com
^ permalink raw reply [flat|nested] 54+ messages in thread
* Re: [OpenWrt-Devel] ATH10K VLAN firmware issue
@ 2016-11-15 14:55 ` Ben Greear
0 siblings, 0 replies; 54+ messages in thread
From: Ben Greear @ 2016-11-15 14:55 UTC (permalink / raw)
To: voncken; +Cc: 'OpenWrt Development List', linux-wireless, ath10k
The beta-18 release on my web page has the fix and should work fine.
Probably soon I will promote the beta-18 to final release
status. Any help in testing and verifying the beta works well
is welcome.
Thanks,
Ben
On 11/15/2016 06:37 AM, voncken wrote:
> Hi Ben,
>
> Do you plan to release a candelatech firmware with this fix?
>
> Regards.
>
> Cedric Voncken.
>> -----Message d'origine-----
>> De : linux-wireless-owner@vger.kernel.org [mailto:linux-wireless-
>> owner@vger.kernel.org] De la part de Ben Greear
>> Envoyé : samedi 5 novembre 2016 15:35
>> À : Sebastian Gottschall; yu-chieh kung; Bruno Antunes
>> Cc : Mauro Mozzarelli; linux-wireless@vger.kernel.org; OpenWrt
>> Development List; ath10k@lists.infradead.org
>> Objet : Re: [OpenWrt-Devel] ATH10K VLAN firmware issue
>>
>> Looks to me like 10.4 defaults to the right value, but possibly there
>> are other issues with it. I tested my CT 10.4 and it worked OK with
>> vlans for me.
>>
>> Thanks,
>> Ben
>>
>> On 11/05/2016 01:05 AM, Sebastian Gottschall wrote:
>>> would be good if qca can fix this bug finally in all available
>>> firmwares. its a very annoying issue since a long time
>>>
>>> Sebastian
>>>
>>>
>>> Am 04.11.2016 um 23:23 schrieb Ben Greear:
>>>> The bug appears that vlan-tx-stripping is unconditionally enabled in
>>>> at least my firmware. I have re-compiled w/out that flag set, and
>> it
>>>> appears to work for me.
>>>>
>>>> Please download this firmware, rename it firmware-2.bin, make sure
>>>> you remove/rename any firmware-5.bin (etc) so mine will load, and
>> see if that fixes your problem.
>>>>
>>>> Please note that it is very likely you will have to use same MAC
>>>> address for the VLAN devices that the underlying station uses in
>> order for this to work.
>>>>
>>>> https://www.candelatech.com/downloads/tmp/firmware-2-full-
>> community.b
>>>> in
>>>>
>>>>
>>>> Thanks,
>>>> Ben
>>>>
>>>>
>>>> On 11/04/2016 02:50 PM, Ben Greear wrote:
>>>>> I can reproduce this in my CT firmware. I'll see if I can fix it,
>>>>> but for stock firmware, it might be that changing the driver to use
>>>>> Ethernet packet type of native-wifi would make .1q vlans work.
>>>>>
>>>>> Thanks,
>>>>> Ben
>>>>>
>>>>> On 11/04/2016 10:28 AM, yu-chieh kung wrote:
>>>>>> I met the same problem before,
>>>>>> if i modify the 1q header to other value (0xaa00) before go into
>> firmware.
>>>>>> I can capture the packet in the air I think the vlan packet is
>>>>>> dropped in firmware.
>>>>>>
>>>>>> 2016-11-04 22:41 GMT+08:00 Bruno Antunes <baantunes@gmail.com>:
>>>>>>> On 4 November 2016 at 14:18, Mauro Mozzarelli
>> <openwrt@ezplanet.net> wrote:
>>>>>>>> Since the capability is implemented in software you might be
>>>>>>>> testing the limit of your router's CPU i/o speed.
>>>>>>>
>>>>>>> By loading the module in rawmode?
>>>>>>>
>>>>>>> The AP is an APU and Sta is an APU2.
>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>> On 04/11/16 14:13, Bruno Antunes wrote:
>>>>>>>>>
>>>>>>>>> Hi all,
>>>>>>>>>
>>>>>>>>> Old thread but I think the issue is still present.
>>>>>>>>>
>>>>>>>>> I'm running a setup with VLANs with WDS and ath10k cards.
>>>>>>>>>
>>>>>>>>> To make it work both cards must be loaded in rawmode, AP and
>>>>>>>>> Sta, and with no security.
>>>>>>>>>
>>>>>>>>> I'm using a OpenWrt trunk r49941 and the most recent firmware,
>>>>>>>>> 10.2.4.70.58, from Kalle ath10k firmware tree.
>>>>>>>>>
>>>>>>>>> Although it works the throughput is very bad.
>>>>>>>>> Are there any alternatives to improve the throughput.
>>>>>>>>>
>>>>>>>>> Best Regards,
>>>>>>>>> Bruno
>>>>>>>>>
>>>>>>>>> On 9 December 2015 at 17:24, voncken <cedric.voncken@acksys.fr>
>> wrote:
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>> -----Message d'origine-----
>>>>>>>>>>> De : Ben Greear [mailto:greearb@candelatech.com] Envoyé :
>>>>>>>>>>> mercredi 9 décembre 2015 16:34 À : Cedric VONCKEN;
>>>>>>>>>>> ath10k@lists.infradead.org; linux-wireless Objet : Re: ATH10K
>>>>>>>>>>> VLAN firmware issue
>>>>>>>>>>>
>>>>>>>>>>> This only happens when you use STA + WDS, or is .1q broken
>>>>>>>>>>> for you in other cases as well?
>>>>>>>>>>
>>>>>>>>>> No, this issue occurs in all modes (STA, STA + WDS, AP).
>>>>>>>>>>
>>>>>>>>>> Thanks
>>>>>>>>>>
>>>>>>>>>> Cedric.
>>>>>>>>>>
>>>>>>>>>>> Thanks,
>>>>>>>>>>> Ben
>>>>>>>>>>>
>>>>>>>>>>> On 12/08/2015 06:29 AM, Cedric VONCKEN wrote:
>>>>>>>>>>>>
>>>>>>>>>>>> I'm testing to transmit frame with 802.1q tag (VLAN).
>>>>>>>>>>>>
>>>>>>>>>>>> My client is set in STA + WDS and the netdev is bridged
>> with eth0.
>>>>>>>>>>>> I have a computer with vlan configuration set connected
>>>>>>>>>>>> to the STA eth0.
>>>>>>>>>>>>
>>>>>>>>>>>> If I try to transmit frames with 802.1q tag, the frames
>>>>>>>>>>>> are not
>>>>>>>>>>
>>>>>>>>>> sent.
>>>>>>>>>>>>
>>>>>>>>>>>> I checked with wireless sniffer, and I don't see the
>>>>>>>>>>>> frame with VLAN tag (the frames without VLAN tag are sent).
>>>>>>>>>>>>
>>>>>>>>>>>> I tested with firmware 10.2.4.70.14-2 from kale github,
>>>>>>>>>>>> 10.1.467-ct-com-full-015 from candelatech and 10.2.4.70-2
>>>>>>>>>>>> from openwrt, and in all cases I have the same issue.
>>>>>>>>>>>>
>>>>>>>>>>>> Thanks for your help.
>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>> --
>>>>>>>>>>>> To unsubscribe from this list: send the line "unsubscribe
>>>>>>>>>>>> linux-wireless" in the body of a message to
>>>>>>>>>>>> majordomo@vger.kernel.org More majordomo info at
>>>>>>>>>>>> http://vger.kernel.org/majordomo-info.html
>>>>>>>>>>>>
>>>>>>>>>>> --
>>>>>>>>>>> Ben Greear <greearb@candelatech.com> Candela Technologies Inc
>>>>>>>>>>> http://www.candelatech.com
>>>>>>>>>>
>>>>>>>>>> --
>>>>>>>>>> To unsubscribe from this list: send the line "unsubscribe
>> linux-wireless"
>>>>>>>>>> in
>>>>>>>>>> the body of a message to majordomo@vger.kernel.org More
>>>>>>>>>> majordomo info at http://vger.kernel.org/majordomo-info.html
>>>>>>>>>
>>>>>>>>> _______________________________________________
>>>>>>>>> openwrt-devel mailing list
>>>>>>>>> openwrt-devel@lists.openwrt.org
>>>>>>>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-
>> devel
>>>>>>>>
>>>>>>>> _______________________________________________
>>>>>>>> openwrt-devel mailing list
>>>>>>>> openwrt-devel@lists.openwrt.org
>>>>>>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>>>>>>>
>>>>>>> _______________________________________________
>>>>>>> ath10k mailing list
>>>>>>> ath10k@lists.infradead.org
>>>>>>> http://lists.infradead.org/mailman/listinfo/ath10k
>>>>>>
>>>>>
>>>>>
>>>>
>>>>
>>>
>>>
>>
>> --
>> Ben Greear <greearb@candelatech.com>
>> Candela Technologies Inc http://www.candelatech.com
>
--
Ben Greear <greearb@candelatech.com>
Candela Technologies Inc http://www.candelatech.com
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 54+ messages in thread
* Re: [OpenWrt-Devel] ATH10K VLAN firmware issue
2016-11-15 14:55 ` Ben Greear
@ 2016-11-15 15:00 ` Bruno Antunes
-1 siblings, 0 replies; 54+ messages in thread
From: Bruno Antunes @ 2016-11-15 15:00 UTC (permalink / raw)
To: Ben Greear; +Cc: voncken, OpenWrt Development List, linux-wireless, ath10k
On 15 November 2016 at 14:55, Ben Greear <greearb@candelatech.com> wrote:
> The beta-18 release on my web page has the fix and should work fine.
>
> Probably soon I will promote the beta-18 to final release
> status. Any help in testing and verifying the beta works well
> is welcome.
I will also do testing with that version.
For clarity can I refer you and your firmware releases in the bug report?
Thanks,
Bruno
>
> Thanks,
> Ben
>
> On 11/15/2016 06:37 AM, voncken wrote:
>>
>> Hi Ben,
>>
>> Do you plan to release a candelatech firmware with this fix?
>>
>> Regards.
>>
>> Cedric Voncken.
>>>
>>> -----Message d'origine-----
>>> De : linux-wireless-owner@vger.kernel.org [mailto:linux-wireless-
>>> owner@vger.kernel.org] De la part de Ben Greear
>>> Envoy=C3=A9 : samedi 5 novembre 2016 15:35
>>> =C3=80 : Sebastian Gottschall; yu-chieh kung; Bruno Antunes
>>> Cc : Mauro Mozzarelli; linux-wireless@vger.kernel.org; OpenWrt
>>> Development List; ath10k@lists.infradead.org
>>> Objet : Re: [OpenWrt-Devel] ATH10K VLAN firmware issue
>>>
>>>
>>> Looks to me like 10.4 defaults to the right value, but possibly there
>>> are other issues with it. I tested my CT 10.4 and it worked OK with
>>> vlans for me.
>>>
>>> Thanks,
>>> Ben
>>>
>>> On 11/05/2016 01:05 AM, Sebastian Gottschall wrote:
>>>>
>>>> would be good if qca can fix this bug finally in all available
>>>> firmwares. its a very annoying issue since a long time
>>>>
>>>> Sebastian
>>>>
>>>>
>>>> Am 04.11.2016 um 23:23 schrieb Ben Greear:
>>>>>
>>>>> The bug appears that vlan-tx-stripping is unconditionally enabled in
>>>>> at least my firmware. I have re-compiled w/out that flag set, and
>>>
>>> it
>>>>>
>>>>> appears to work for me.
>>>>>
>>>>> Please download this firmware, rename it firmware-2.bin, make sure
>>>>> you remove/rename any firmware-5.bin (etc) so mine will load, and
>>>
>>> see if that fixes your problem.
>>>>>
>>>>>
>>>>> Please note that it is very likely you will have to use same MAC
>>>>> address for the VLAN devices that the underlying station uses in
>>>
>>> order for this to work.
>>>>>
>>>>>
>>>>> https://www.candelatech.com/downloads/tmp/firmware-2-full-
>>>
>>> community.b
>>>>>
>>>>> in
>>>>>
>>>>>
>>>>> Thanks,
>>>>> Ben
>>>>>
>>>>>
>>>>> On 11/04/2016 02:50 PM, Ben Greear wrote:
>>>>>>
>>>>>> I can reproduce this in my CT firmware. I'll see if I can fix it,
>>>>>> but for stock firmware, it might be that changing the driver to use
>>>>>> Ethernet packet type of native-wifi would make .1q vlans work.
>>>>>>
>>>>>> Thanks,
>>>>>> Ben
>>>>>>
>>>>>> On 11/04/2016 10:28 AM, yu-chieh kung wrote:
>>>>>>>
>>>>>>> I met the same problem before,
>>>>>>> if i modify the 1q header to other value (0xaa00) before go into
>>>
>>> firmware.
>>>>>>>
>>>>>>> I can capture the packet in the air I think the vlan packet is
>>>>>>> dropped in firmware.
>>>>>>>
>>>>>>> 2016-11-04 22:41 GMT+08:00 Bruno Antunes <baantunes@gmail.com>:
>>>>>>>>
>>>>>>>> On 4 November 2016 at 14:18, Mauro Mozzarelli
>>>
>>> <openwrt@ezplanet.net> wrote:
>>>>>>>>>
>>>>>>>>> Since the capability is implemented in software you might be
>>>>>>>>> testing the limit of your router's CPU i/o speed.
>>>>>>>>
>>>>>>>>
>>>>>>>> By loading the module in rawmode?
>>>>>>>>
>>>>>>>> The AP is an APU and Sta is an APU2.
>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>> On 04/11/16 14:13, Bruno Antunes wrote:
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>> Hi all,
>>>>>>>>>>
>>>>>>>>>> Old thread but I think the issue is still present.
>>>>>>>>>>
>>>>>>>>>> I'm running a setup with VLANs with WDS and ath10k cards.
>>>>>>>>>>
>>>>>>>>>> To make it work both cards must be loaded in rawmode, AP and
>>>>>>>>>> Sta, and with no security.
>>>>>>>>>>
>>>>>>>>>> I'm using a OpenWrt trunk r49941 and the most recent firmware,
>>>>>>>>>> 10.2.4.70.58, from Kalle ath10k firmware tree.
>>>>>>>>>>
>>>>>>>>>> Although it works the throughput is very bad.
>>>>>>>>>> Are there any alternatives to improve the throughput.
>>>>>>>>>>
>>>>>>>>>> Best Regards,
>>>>>>>>>> Bruno
>>>>>>>>>>
>>>>>>>>>> On 9 December 2015 at 17:24, voncken <cedric.voncken@acksys.fr>
>>>
>>> wrote:
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>>> -----Message d'origine-----
>>>>>>>>>>>> De : Ben Greear [mailto:greearb@candelatech.com] Envoy=C3=A9 :
>>>>>>>>>>>> mercredi 9 d=C3=A9cembre 2015 16:34 =C3=80 : Cedric VONCKEN;
>>>>>>>>>>>> ath10k@lists.infradead.org; linux-wireless Objet : Re: ATH10K
>>>>>>>>>>>> VLAN firmware issue
>>>>>>>>>>>>
>>>>>>>>>>>> This only happens when you use STA + WDS, or is .1q broken
>>>>>>>>>>>> for you in other cases as well?
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>> No, this issue occurs in all modes (STA, STA + WDS, AP).
>>>>>>>>>>>
>>>>>>>>>>> Thanks
>>>>>>>>>>>
>>>>>>>>>>> Cedric.
>>>>>>>>>>>
>>>>>>>>>>>> Thanks,
>>>>>>>>>>>> Ben
>>>>>>>>>>>>
>>>>>>>>>>>> On 12/08/2015 06:29 AM, Cedric VONCKEN wrote:
>>>>>>>>>>>>>
>>>>>>>>>>>>>
>>>>>>>>>>>>> I'm testing to transmit frame with 802.1q tag (VLAN).
>>>>>>>>>>>>>
>>>>>>>>>>>>> My client is set in STA + WDS and the netdev is bridged
>>>
>>> with eth0.
>>>>>>>>>>>>>
>>>>>>>>>>>>> I have a computer with vlan configuration set connected
>>>>>>>>>>>>> to the STA eth0.
>>>>>>>>>>>>>
>>>>>>>>>>>>> If I try to transmit frames with 802.1q tag, the frames
>>>>>>>>>>>>> are not
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>> sent.
>>>>>>>>>>>>>
>>>>>>>>>>>>>
>>>>>>>>>>>>> I checked with wireless sniffer, and I don't see the
>>>>>>>>>>>>> frame with VLAN tag (the frames without VLAN tag are sent).
>>>>>>>>>>>>>
>>>>>>>>>>>>> I tested with firmware 10.2.4.70.14-2 from kale github,
>>>>>>>>>>>>> 10.1.467-ct-com-full-015 from candelatech and 10.2.4.70-2
>>>>>>>>>>>>> from openwrt, and in all cases I have the same issue.
>>>>>>>>>>>>>
>>>>>>>>>>>>> Thanks for your help.
>>>>>>>>>>>>>
>>>>>>>>>>>>>
>>>>>>>>>>>>> --
>>>>>>>>>>>>> To unsubscribe from this list: send the line "unsubscribe
>>>>>>>>>>>>> linux-wireless" in the body of a message to
>>>>>>>>>>>>> majordomo@vger.kernel.org More majordomo info at
>>>>>>>>>>>>> http://vger.kernel.org/majordomo-info.html
>>>>>>>>>>>>>
>>>>>>>>>>>> --
>>>>>>>>>>>> Ben Greear <greearb@candelatech.com> Candela Technologies Inc
>>>>>>>>>>>> http://www.candelatech.com
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>> --
>>>>>>>>>>> To unsubscribe from this list: send the line "unsubscribe
>>>
>>> linux-wireless"
>>>>>>>>>>>
>>>>>>>>>>> in
>>>>>>>>>>> the body of a message to majordomo@vger.kernel.org More
>>>>>>>>>>> majordomo info at http://vger.kernel.org/majordomo-info.html
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>> _______________________________________________
>>>>>>>>>> openwrt-devel mailing list
>>>>>>>>>> openwrt-devel@lists.openwrt.org
>>>>>>>>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-
>>>
>>> devel
>>>>>>>>>
>>>>>>>>>
>>>>>>>>> _______________________________________________
>>>>>>>>> openwrt-devel mailing list
>>>>>>>>> openwrt-devel@lists.openwrt.org
>>>>>>>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>>>>>>>>
>>>>>>>>
>>>>>>>> _______________________________________________
>>>>>>>> ath10k mailing list
>>>>>>>> ath10k@lists.infradead.org
>>>>>>>> http://lists.infradead.org/mailman/listinfo/ath10k
>>>>>>>
>>>>>>>
>>>>>>
>>>>>>
>>>>>
>>>>>
>>>>
>>>>
>>>
>>> --
>>> Ben Greear <greearb@candelatech.com>
>>> Candela Technologies Inc http://www.candelatech.com
>>
>>
>
> --
> Ben Greear <greearb@candelatech.com>
> Candela Technologies Inc http://www.candelatech.com
> _______________________________________________
> openwrt-devel mailing list
> openwrt-devel@lists.openwrt.org
> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
^ permalink raw reply [flat|nested] 54+ messages in thread
* Re: [OpenWrt-Devel] ATH10K VLAN firmware issue
@ 2016-11-15 15:00 ` Bruno Antunes
0 siblings, 0 replies; 54+ messages in thread
From: Bruno Antunes @ 2016-11-15 15:00 UTC (permalink / raw)
To: Ben Greear; +Cc: OpenWrt Development List, linux-wireless, ath10k, voncken
On 15 November 2016 at 14:55, Ben Greear <greearb@candelatech.com> wrote:
> The beta-18 release on my web page has the fix and should work fine.
>
> Probably soon I will promote the beta-18 to final release
> status. Any help in testing and verifying the beta works well
> is welcome.
I will also do testing with that version.
For clarity can I refer you and your firmware releases in the bug report?
Thanks,
Bruno
>
> Thanks,
> Ben
>
> On 11/15/2016 06:37 AM, voncken wrote:
>>
>> Hi Ben,
>>
>> Do you plan to release a candelatech firmware with this fix?
>>
>> Regards.
>>
>> Cedric Voncken.
>>>
>>> -----Message d'origine-----
>>> De : linux-wireless-owner@vger.kernel.org [mailto:linux-wireless-
>>> owner@vger.kernel.org] De la part de Ben Greear
>>> Envoyé : samedi 5 novembre 2016 15:35
>>> À : Sebastian Gottschall; yu-chieh kung; Bruno Antunes
>>> Cc : Mauro Mozzarelli; linux-wireless@vger.kernel.org; OpenWrt
>>> Development List; ath10k@lists.infradead.org
>>> Objet : Re: [OpenWrt-Devel] ATH10K VLAN firmware issue
>>>
>>>
>>> Looks to me like 10.4 defaults to the right value, but possibly there
>>> are other issues with it. I tested my CT 10.4 and it worked OK with
>>> vlans for me.
>>>
>>> Thanks,
>>> Ben
>>>
>>> On 11/05/2016 01:05 AM, Sebastian Gottschall wrote:
>>>>
>>>> would be good if qca can fix this bug finally in all available
>>>> firmwares. its a very annoying issue since a long time
>>>>
>>>> Sebastian
>>>>
>>>>
>>>> Am 04.11.2016 um 23:23 schrieb Ben Greear:
>>>>>
>>>>> The bug appears that vlan-tx-stripping is unconditionally enabled in
>>>>> at least my firmware. I have re-compiled w/out that flag set, and
>>>
>>> it
>>>>>
>>>>> appears to work for me.
>>>>>
>>>>> Please download this firmware, rename it firmware-2.bin, make sure
>>>>> you remove/rename any firmware-5.bin (etc) so mine will load, and
>>>
>>> see if that fixes your problem.
>>>>>
>>>>>
>>>>> Please note that it is very likely you will have to use same MAC
>>>>> address for the VLAN devices that the underlying station uses in
>>>
>>> order for this to work.
>>>>>
>>>>>
>>>>> https://www.candelatech.com/downloads/tmp/firmware-2-full-
>>>
>>> community.b
>>>>>
>>>>> in
>>>>>
>>>>>
>>>>> Thanks,
>>>>> Ben
>>>>>
>>>>>
>>>>> On 11/04/2016 02:50 PM, Ben Greear wrote:
>>>>>>
>>>>>> I can reproduce this in my CT firmware. I'll see if I can fix it,
>>>>>> but for stock firmware, it might be that changing the driver to use
>>>>>> Ethernet packet type of native-wifi would make .1q vlans work.
>>>>>>
>>>>>> Thanks,
>>>>>> Ben
>>>>>>
>>>>>> On 11/04/2016 10:28 AM, yu-chieh kung wrote:
>>>>>>>
>>>>>>> I met the same problem before,
>>>>>>> if i modify the 1q header to other value (0xaa00) before go into
>>>
>>> firmware.
>>>>>>>
>>>>>>> I can capture the packet in the air I think the vlan packet is
>>>>>>> dropped in firmware.
>>>>>>>
>>>>>>> 2016-11-04 22:41 GMT+08:00 Bruno Antunes <baantunes@gmail.com>:
>>>>>>>>
>>>>>>>> On 4 November 2016 at 14:18, Mauro Mozzarelli
>>>
>>> <openwrt@ezplanet.net> wrote:
>>>>>>>>>
>>>>>>>>> Since the capability is implemented in software you might be
>>>>>>>>> testing the limit of your router's CPU i/o speed.
>>>>>>>>
>>>>>>>>
>>>>>>>> By loading the module in rawmode?
>>>>>>>>
>>>>>>>> The AP is an APU and Sta is an APU2.
>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>> On 04/11/16 14:13, Bruno Antunes wrote:
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>> Hi all,
>>>>>>>>>>
>>>>>>>>>> Old thread but I think the issue is still present.
>>>>>>>>>>
>>>>>>>>>> I'm running a setup with VLANs with WDS and ath10k cards.
>>>>>>>>>>
>>>>>>>>>> To make it work both cards must be loaded in rawmode, AP and
>>>>>>>>>> Sta, and with no security.
>>>>>>>>>>
>>>>>>>>>> I'm using a OpenWrt trunk r49941 and the most recent firmware,
>>>>>>>>>> 10.2.4.70.58, from Kalle ath10k firmware tree.
>>>>>>>>>>
>>>>>>>>>> Although it works the throughput is very bad.
>>>>>>>>>> Are there any alternatives to improve the throughput.
>>>>>>>>>>
>>>>>>>>>> Best Regards,
>>>>>>>>>> Bruno
>>>>>>>>>>
>>>>>>>>>> On 9 December 2015 at 17:24, voncken <cedric.voncken@acksys.fr>
>>>
>>> wrote:
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>>> -----Message d'origine-----
>>>>>>>>>>>> De : Ben Greear [mailto:greearb@candelatech.com] Envoyé :
>>>>>>>>>>>> mercredi 9 décembre 2015 16:34 À : Cedric VONCKEN;
>>>>>>>>>>>> ath10k@lists.infradead.org; linux-wireless Objet : Re: ATH10K
>>>>>>>>>>>> VLAN firmware issue
>>>>>>>>>>>>
>>>>>>>>>>>> This only happens when you use STA + WDS, or is .1q broken
>>>>>>>>>>>> for you in other cases as well?
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>> No, this issue occurs in all modes (STA, STA + WDS, AP).
>>>>>>>>>>>
>>>>>>>>>>> Thanks
>>>>>>>>>>>
>>>>>>>>>>> Cedric.
>>>>>>>>>>>
>>>>>>>>>>>> Thanks,
>>>>>>>>>>>> Ben
>>>>>>>>>>>>
>>>>>>>>>>>> On 12/08/2015 06:29 AM, Cedric VONCKEN wrote:
>>>>>>>>>>>>>
>>>>>>>>>>>>>
>>>>>>>>>>>>> I'm testing to transmit frame with 802.1q tag (VLAN).
>>>>>>>>>>>>>
>>>>>>>>>>>>> My client is set in STA + WDS and the netdev is bridged
>>>
>>> with eth0.
>>>>>>>>>>>>>
>>>>>>>>>>>>> I have a computer with vlan configuration set connected
>>>>>>>>>>>>> to the STA eth0.
>>>>>>>>>>>>>
>>>>>>>>>>>>> If I try to transmit frames with 802.1q tag, the frames
>>>>>>>>>>>>> are not
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>> sent.
>>>>>>>>>>>>>
>>>>>>>>>>>>>
>>>>>>>>>>>>> I checked with wireless sniffer, and I don't see the
>>>>>>>>>>>>> frame with VLAN tag (the frames without VLAN tag are sent).
>>>>>>>>>>>>>
>>>>>>>>>>>>> I tested with firmware 10.2.4.70.14-2 from kale github,
>>>>>>>>>>>>> 10.1.467-ct-com-full-015 from candelatech and 10.2.4.70-2
>>>>>>>>>>>>> from openwrt, and in all cases I have the same issue.
>>>>>>>>>>>>>
>>>>>>>>>>>>> Thanks for your help.
>>>>>>>>>>>>>
>>>>>>>>>>>>>
>>>>>>>>>>>>> --
>>>>>>>>>>>>> To unsubscribe from this list: send the line "unsubscribe
>>>>>>>>>>>>> linux-wireless" in the body of a message to
>>>>>>>>>>>>> majordomo@vger.kernel.org More majordomo info at
>>>>>>>>>>>>> http://vger.kernel.org/majordomo-info.html
>>>>>>>>>>>>>
>>>>>>>>>>>> --
>>>>>>>>>>>> Ben Greear <greearb@candelatech.com> Candela Technologies Inc
>>>>>>>>>>>> http://www.candelatech.com
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>> --
>>>>>>>>>>> To unsubscribe from this list: send the line "unsubscribe
>>>
>>> linux-wireless"
>>>>>>>>>>>
>>>>>>>>>>> in
>>>>>>>>>>> the body of a message to majordomo@vger.kernel.org More
>>>>>>>>>>> majordomo info at http://vger.kernel.org/majordomo-info.html
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>> _______________________________________________
>>>>>>>>>> openwrt-devel mailing list
>>>>>>>>>> openwrt-devel@lists.openwrt.org
>>>>>>>>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-
>>>
>>> devel
>>>>>>>>>
>>>>>>>>>
>>>>>>>>> _______________________________________________
>>>>>>>>> openwrt-devel mailing list
>>>>>>>>> openwrt-devel@lists.openwrt.org
>>>>>>>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>>>>>>>>
>>>>>>>>
>>>>>>>> _______________________________________________
>>>>>>>> ath10k mailing list
>>>>>>>> ath10k@lists.infradead.org
>>>>>>>> http://lists.infradead.org/mailman/listinfo/ath10k
>>>>>>>
>>>>>>>
>>>>>>
>>>>>>
>>>>>
>>>>>
>>>>
>>>>
>>>
>>> --
>>> Ben Greear <greearb@candelatech.com>
>>> Candela Technologies Inc http://www.candelatech.com
>>
>>
>
> --
> Ben Greear <greearb@candelatech.com>
> Candela Technologies Inc http://www.candelatech.com
> _______________________________________________
> openwrt-devel mailing list
> openwrt-devel@lists.openwrt.org
> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 54+ messages in thread
* Re: [OpenWrt-Devel] ATH10K VLAN firmware issue
2016-11-15 15:00 ` Bruno Antunes
@ 2016-11-15 15:06 ` Ben Greear
-1 siblings, 0 replies; 54+ messages in thread
From: Ben Greear @ 2016-11-15 15:06 UTC (permalink / raw)
To: Bruno Antunes; +Cc: voncken, OpenWrt Development List, linux-wireless, ath10k
On 11/15/2016 07:00 AM, Bruno Antunes wrote:
> On 15 November 2016 at 14:55, Ben Greear <greearb@candelatech.com> wrote:
>> The beta-18 release on my web page has the fix and should work fine.
>>
>> Probably soon I will promote the beta-18 to final release
>> status. Any help in testing and verifying the beta works well
>> is welcome.
>
> I will also do testing with that version.
>
> For clarity can I refer you and your firmware releases in the bug report?
It is fine by me. It is a one-line patch to fix the firmware...QCA
can ask me as well if they don't figure it out on their own.
Thanks,
Ben
>
> Thanks,
> Bruno
>>
>> Thanks,
>> Ben
>>
>> On 11/15/2016 06:37 AM, voncken wrote:
>>>
>>> Hi Ben,
>>>
>>> Do you plan to release a candelatech firmware with this fix?
>>>
>>> Regards.
>>>
>>> Cedric Voncken.
>>>>
>>>> -----Message d'origine-----
>>>> De : linux-wireless-owner@vger.kernel.org [mailto:linux-wireless-
>>>> owner@vger.kernel.org] De la part de Ben Greear
>>>> Envoyé : samedi 5 novembre 2016 15:35
>>>> À : Sebastian Gottschall; yu-chieh kung; Bruno Antunes
>>>> Cc : Mauro Mozzarelli; linux-wireless@vger.kernel.org; OpenWrt
>>>> Development List; ath10k@lists.infradead.org
>>>> Objet : Re: [OpenWrt-Devel] ATH10K VLAN firmware issue
>>>>
>>>>
>>>> Looks to me like 10.4 defaults to the right value, but possibly there
>>>> are other issues with it. I tested my CT 10.4 and it worked OK with
>>>> vlans for me.
>>>>
>>>> Thanks,
>>>> Ben
>>>>
>>>> On 11/05/2016 01:05 AM, Sebastian Gottschall wrote:
>>>>>
>>>>> would be good if qca can fix this bug finally in all available
>>>>> firmwares. its a very annoying issue since a long time
>>>>>
>>>>> Sebastian
>>>>>
>>>>>
>>>>> Am 04.11.2016 um 23:23 schrieb Ben Greear:
>>>>>>
>>>>>> The bug appears that vlan-tx-stripping is unconditionally enabled in
>>>>>> at least my firmware. I have re-compiled w/out that flag set, and
>>>>
>>>> it
>>>>>>
>>>>>> appears to work for me.
>>>>>>
>>>>>> Please download this firmware, rename it firmware-2.bin, make sure
>>>>>> you remove/rename any firmware-5.bin (etc) so mine will load, and
>>>>
>>>> see if that fixes your problem.
>>>>>>
>>>>>>
>>>>>> Please note that it is very likely you will have to use same MAC
>>>>>> address for the VLAN devices that the underlying station uses in
>>>>
>>>> order for this to work.
>>>>>>
>>>>>>
>>>>>> https://www.candelatech.com/downloads/tmp/firmware-2-full-
>>>>
>>>> community.b
>>>>>>
>>>>>> in
>>>>>>
>>>>>>
>>>>>> Thanks,
>>>>>> Ben
>>>>>>
>>>>>>
>>>>>> On 11/04/2016 02:50 PM, Ben Greear wrote:
>>>>>>>
>>>>>>> I can reproduce this in my CT firmware. I'll see if I can fix it,
>>>>>>> but for stock firmware, it might be that changing the driver to use
>>>>>>> Ethernet packet type of native-wifi would make .1q vlans work.
>>>>>>>
>>>>>>> Thanks,
>>>>>>> Ben
>>>>>>>
>>>>>>> On 11/04/2016 10:28 AM, yu-chieh kung wrote:
>>>>>>>>
>>>>>>>> I met the same problem before,
>>>>>>>> if i modify the 1q header to other value (0xaa00) before go into
>>>>
>>>> firmware.
>>>>>>>>
>>>>>>>> I can capture the packet in the air I think the vlan packet is
>>>>>>>> dropped in firmware.
>>>>>>>>
>>>>>>>> 2016-11-04 22:41 GMT+08:00 Bruno Antunes <baantunes@gmail.com>:
>>>>>>>>>
>>>>>>>>> On 4 November 2016 at 14:18, Mauro Mozzarelli
>>>>
>>>> <openwrt@ezplanet.net> wrote:
>>>>>>>>>>
>>>>>>>>>> Since the capability is implemented in software you might be
>>>>>>>>>> testing the limit of your router's CPU i/o speed.
>>>>>>>>>
>>>>>>>>>
>>>>>>>>> By loading the module in rawmode?
>>>>>>>>>
>>>>>>>>> The AP is an APU and Sta is an APU2.
>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>> On 04/11/16 14:13, Bruno Antunes wrote:
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>> Hi all,
>>>>>>>>>>>
>>>>>>>>>>> Old thread but I think the issue is still present.
>>>>>>>>>>>
>>>>>>>>>>> I'm running a setup with VLANs with WDS and ath10k cards.
>>>>>>>>>>>
>>>>>>>>>>> To make it work both cards must be loaded in rawmode, AP and
>>>>>>>>>>> Sta, and with no security.
>>>>>>>>>>>
>>>>>>>>>>> I'm using a OpenWrt trunk r49941 and the most recent firmware,
>>>>>>>>>>> 10.2.4.70.58, from Kalle ath10k firmware tree.
>>>>>>>>>>>
>>>>>>>>>>> Although it works the throughput is very bad.
>>>>>>>>>>> Are there any alternatives to improve the throughput.
>>>>>>>>>>>
>>>>>>>>>>> Best Regards,
>>>>>>>>>>> Bruno
>>>>>>>>>>>
>>>>>>>>>>> On 9 December 2015 at 17:24, voncken <cedric.voncken@acksys.fr>
>>>>
>>>> wrote:
>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>>> -----Message d'origine-----
>>>>>>>>>>>>> De : Ben Greear [mailto:greearb@candelatech.com] Envoyé :
>>>>>>>>>>>>> mercredi 9 décembre 2015 16:34 À : Cedric VONCKEN;
>>>>>>>>>>>>> ath10k@lists.infradead.org; linux-wireless Objet : Re: ATH10K
>>>>>>>>>>>>> VLAN firmware issue
>>>>>>>>>>>>>
>>>>>>>>>>>>> This only happens when you use STA + WDS, or is .1q broken
>>>>>>>>>>>>> for you in other cases as well?
>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>> No, this issue occurs in all modes (STA, STA + WDS, AP).
>>>>>>>>>>>>
>>>>>>>>>>>> Thanks
>>>>>>>>>>>>
>>>>>>>>>>>> Cedric.
>>>>>>>>>>>>
>>>>>>>>>>>>> Thanks,
>>>>>>>>>>>>> Ben
>>>>>>>>>>>>>
>>>>>>>>>>>>> On 12/08/2015 06:29 AM, Cedric VONCKEN wrote:
>>>>>>>>>>>>>>
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> I'm testing to transmit frame with 802.1q tag (VLAN).
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> My client is set in STA + WDS and the netdev is bridged
>>>>
>>>> with eth0.
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> I have a computer with vlan configuration set connected
>>>>>>>>>>>>>> to the STA eth0.
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> If I try to transmit frames with 802.1q tag, the frames
>>>>>>>>>>>>>> are not
>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>> sent.
>>>>>>>>>>>>>>
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> I checked with wireless sniffer, and I don't see the
>>>>>>>>>>>>>> frame with VLAN tag (the frames without VLAN tag are sent).
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> I tested with firmware 10.2.4.70.14-2 from kale github,
>>>>>>>>>>>>>> 10.1.467-ct-com-full-015 from candelatech and 10.2.4.70-2
>>>>>>>>>>>>>> from openwrt, and in all cases I have the same issue.
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> Thanks for your help.
>>>>>>>>>>>>>>
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> --
>>>>>>>>>>>>>> To unsubscribe from this list: send the line "unsubscribe
>>>>>>>>>>>>>> linux-wireless" in the body of a message to
>>>>>>>>>>>>>> majordomo@vger.kernel.org More majordomo info at
>>>>>>>>>>>>>> http://vger.kernel.org/majordomo-info.html
>>>>>>>>>>>>>>
>>>>>>>>>>>>> --
>>>>>>>>>>>>> Ben Greear <greearb@candelatech.com> Candela Technologies Inc
>>>>>>>>>>>>> http://www.candelatech.com
>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>> --
>>>>>>>>>>>> To unsubscribe from this list: send the line "unsubscribe
>>>>
>>>> linux-wireless"
>>>>>>>>>>>>
>>>>>>>>>>>> in
>>>>>>>>>>>> the body of a message to majordomo@vger.kernel.org More
>>>>>>>>>>>> majordomo info at http://vger.kernel.org/majordomo-info.html
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>> _______________________________________________
>>>>>>>>>>> openwrt-devel mailing list
>>>>>>>>>>> openwrt-devel@lists.openwrt.org
>>>>>>>>>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-
>>>>
>>>> devel
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>> _______________________________________________
>>>>>>>>>> openwrt-devel mailing list
>>>>>>>>>> openwrt-devel@lists.openwrt.org
>>>>>>>>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>>>>>>>>>
>>>>>>>>>
>>>>>>>>> _______________________________________________
>>>>>>>>> ath10k mailing list
>>>>>>>>> ath10k@lists.infradead.org
>>>>>>>>> http://lists.infradead.org/mailman/listinfo/ath10k
>>>>>>>>
>>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>
>>>>>>
>>>>>
>>>>>
>>>>
>>>> --
>>>> Ben Greear <greearb@candelatech.com>
>>>> Candela Technologies Inc http://www.candelatech.com
>>>
>>>
>>
>> --
>> Ben Greear <greearb@candelatech.com>
>> Candela Technologies Inc http://www.candelatech.com
>> _______________________________________________
>> openwrt-devel mailing list
>> openwrt-devel@lists.openwrt.org
>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>
--
Ben Greear <greearb@candelatech.com>
Candela Technologies Inc http://www.candelatech.com
^ permalink raw reply [flat|nested] 54+ messages in thread
* Re: [OpenWrt-Devel] ATH10K VLAN firmware issue
@ 2016-11-15 15:06 ` Ben Greear
0 siblings, 0 replies; 54+ messages in thread
From: Ben Greear @ 2016-11-15 15:06 UTC (permalink / raw)
To: Bruno Antunes; +Cc: OpenWrt Development List, linux-wireless, ath10k, voncken
On 11/15/2016 07:00 AM, Bruno Antunes wrote:
> On 15 November 2016 at 14:55, Ben Greear <greearb@candelatech.com> wrote:
>> The beta-18 release on my web page has the fix and should work fine.
>>
>> Probably soon I will promote the beta-18 to final release
>> status. Any help in testing and verifying the beta works well
>> is welcome.
>
> I will also do testing with that version.
>
> For clarity can I refer you and your firmware releases in the bug report?
It is fine by me. It is a one-line patch to fix the firmware...QCA
can ask me as well if they don't figure it out on their own.
Thanks,
Ben
>
> Thanks,
> Bruno
>>
>> Thanks,
>> Ben
>>
>> On 11/15/2016 06:37 AM, voncken wrote:
>>>
>>> Hi Ben,
>>>
>>> Do you plan to release a candelatech firmware with this fix?
>>>
>>> Regards.
>>>
>>> Cedric Voncken.
>>>>
>>>> -----Message d'origine-----
>>>> De : linux-wireless-owner@vger.kernel.org [mailto:linux-wireless-
>>>> owner@vger.kernel.org] De la part de Ben Greear
>>>> Envoyé : samedi 5 novembre 2016 15:35
>>>> À : Sebastian Gottschall; yu-chieh kung; Bruno Antunes
>>>> Cc : Mauro Mozzarelli; linux-wireless@vger.kernel.org; OpenWrt
>>>> Development List; ath10k@lists.infradead.org
>>>> Objet : Re: [OpenWrt-Devel] ATH10K VLAN firmware issue
>>>>
>>>>
>>>> Looks to me like 10.4 defaults to the right value, but possibly there
>>>> are other issues with it. I tested my CT 10.4 and it worked OK with
>>>> vlans for me.
>>>>
>>>> Thanks,
>>>> Ben
>>>>
>>>> On 11/05/2016 01:05 AM, Sebastian Gottschall wrote:
>>>>>
>>>>> would be good if qca can fix this bug finally in all available
>>>>> firmwares. its a very annoying issue since a long time
>>>>>
>>>>> Sebastian
>>>>>
>>>>>
>>>>> Am 04.11.2016 um 23:23 schrieb Ben Greear:
>>>>>>
>>>>>> The bug appears that vlan-tx-stripping is unconditionally enabled in
>>>>>> at least my firmware. I have re-compiled w/out that flag set, and
>>>>
>>>> it
>>>>>>
>>>>>> appears to work for me.
>>>>>>
>>>>>> Please download this firmware, rename it firmware-2.bin, make sure
>>>>>> you remove/rename any firmware-5.bin (etc) so mine will load, and
>>>>
>>>> see if that fixes your problem.
>>>>>>
>>>>>>
>>>>>> Please note that it is very likely you will have to use same MAC
>>>>>> address for the VLAN devices that the underlying station uses in
>>>>
>>>> order for this to work.
>>>>>>
>>>>>>
>>>>>> https://www.candelatech.com/downloads/tmp/firmware-2-full-
>>>>
>>>> community.b
>>>>>>
>>>>>> in
>>>>>>
>>>>>>
>>>>>> Thanks,
>>>>>> Ben
>>>>>>
>>>>>>
>>>>>> On 11/04/2016 02:50 PM, Ben Greear wrote:
>>>>>>>
>>>>>>> I can reproduce this in my CT firmware. I'll see if I can fix it,
>>>>>>> but for stock firmware, it might be that changing the driver to use
>>>>>>> Ethernet packet type of native-wifi would make .1q vlans work.
>>>>>>>
>>>>>>> Thanks,
>>>>>>> Ben
>>>>>>>
>>>>>>> On 11/04/2016 10:28 AM, yu-chieh kung wrote:
>>>>>>>>
>>>>>>>> I met the same problem before,
>>>>>>>> if i modify the 1q header to other value (0xaa00) before go into
>>>>
>>>> firmware.
>>>>>>>>
>>>>>>>> I can capture the packet in the air I think the vlan packet is
>>>>>>>> dropped in firmware.
>>>>>>>>
>>>>>>>> 2016-11-04 22:41 GMT+08:00 Bruno Antunes <baantunes@gmail.com>:
>>>>>>>>>
>>>>>>>>> On 4 November 2016 at 14:18, Mauro Mozzarelli
>>>>
>>>> <openwrt@ezplanet.net> wrote:
>>>>>>>>>>
>>>>>>>>>> Since the capability is implemented in software you might be
>>>>>>>>>> testing the limit of your router's CPU i/o speed.
>>>>>>>>>
>>>>>>>>>
>>>>>>>>> By loading the module in rawmode?
>>>>>>>>>
>>>>>>>>> The AP is an APU and Sta is an APU2.
>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>> On 04/11/16 14:13, Bruno Antunes wrote:
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>> Hi all,
>>>>>>>>>>>
>>>>>>>>>>> Old thread but I think the issue is still present.
>>>>>>>>>>>
>>>>>>>>>>> I'm running a setup with VLANs with WDS and ath10k cards.
>>>>>>>>>>>
>>>>>>>>>>> To make it work both cards must be loaded in rawmode, AP and
>>>>>>>>>>> Sta, and with no security.
>>>>>>>>>>>
>>>>>>>>>>> I'm using a OpenWrt trunk r49941 and the most recent firmware,
>>>>>>>>>>> 10.2.4.70.58, from Kalle ath10k firmware tree.
>>>>>>>>>>>
>>>>>>>>>>> Although it works the throughput is very bad.
>>>>>>>>>>> Are there any alternatives to improve the throughput.
>>>>>>>>>>>
>>>>>>>>>>> Best Regards,
>>>>>>>>>>> Bruno
>>>>>>>>>>>
>>>>>>>>>>> On 9 December 2015 at 17:24, voncken <cedric.voncken@acksys.fr>
>>>>
>>>> wrote:
>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>>> -----Message d'origine-----
>>>>>>>>>>>>> De : Ben Greear [mailto:greearb@candelatech.com] Envoyé :
>>>>>>>>>>>>> mercredi 9 décembre 2015 16:34 À : Cedric VONCKEN;
>>>>>>>>>>>>> ath10k@lists.infradead.org; linux-wireless Objet : Re: ATH10K
>>>>>>>>>>>>> VLAN firmware issue
>>>>>>>>>>>>>
>>>>>>>>>>>>> This only happens when you use STA + WDS, or is .1q broken
>>>>>>>>>>>>> for you in other cases as well?
>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>> No, this issue occurs in all modes (STA, STA + WDS, AP).
>>>>>>>>>>>>
>>>>>>>>>>>> Thanks
>>>>>>>>>>>>
>>>>>>>>>>>> Cedric.
>>>>>>>>>>>>
>>>>>>>>>>>>> Thanks,
>>>>>>>>>>>>> Ben
>>>>>>>>>>>>>
>>>>>>>>>>>>> On 12/08/2015 06:29 AM, Cedric VONCKEN wrote:
>>>>>>>>>>>>>>
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> I'm testing to transmit frame with 802.1q tag (VLAN).
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> My client is set in STA + WDS and the netdev is bridged
>>>>
>>>> with eth0.
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> I have a computer with vlan configuration set connected
>>>>>>>>>>>>>> to the STA eth0.
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> If I try to transmit frames with 802.1q tag, the frames
>>>>>>>>>>>>>> are not
>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>> sent.
>>>>>>>>>>>>>>
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> I checked with wireless sniffer, and I don't see the
>>>>>>>>>>>>>> frame with VLAN tag (the frames without VLAN tag are sent).
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> I tested with firmware 10.2.4.70.14-2 from kale github,
>>>>>>>>>>>>>> 10.1.467-ct-com-full-015 from candelatech and 10.2.4.70-2
>>>>>>>>>>>>>> from openwrt, and in all cases I have the same issue.
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> Thanks for your help.
>>>>>>>>>>>>>>
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> --
>>>>>>>>>>>>>> To unsubscribe from this list: send the line "unsubscribe
>>>>>>>>>>>>>> linux-wireless" in the body of a message to
>>>>>>>>>>>>>> majordomo@vger.kernel.org More majordomo info at
>>>>>>>>>>>>>> http://vger.kernel.org/majordomo-info.html
>>>>>>>>>>>>>>
>>>>>>>>>>>>> --
>>>>>>>>>>>>> Ben Greear <greearb@candelatech.com> Candela Technologies Inc
>>>>>>>>>>>>> http://www.candelatech.com
>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>> --
>>>>>>>>>>>> To unsubscribe from this list: send the line "unsubscribe
>>>>
>>>> linux-wireless"
>>>>>>>>>>>>
>>>>>>>>>>>> in
>>>>>>>>>>>> the body of a message to majordomo@vger.kernel.org More
>>>>>>>>>>>> majordomo info at http://vger.kernel.org/majordomo-info.html
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>> _______________________________________________
>>>>>>>>>>> openwrt-devel mailing list
>>>>>>>>>>> openwrt-devel@lists.openwrt.org
>>>>>>>>>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-
>>>>
>>>> devel
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>> _______________________________________________
>>>>>>>>>> openwrt-devel mailing list
>>>>>>>>>> openwrt-devel@lists.openwrt.org
>>>>>>>>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>>>>>>>>>
>>>>>>>>>
>>>>>>>>> _______________________________________________
>>>>>>>>> ath10k mailing list
>>>>>>>>> ath10k@lists.infradead.org
>>>>>>>>> http://lists.infradead.org/mailman/listinfo/ath10k
>>>>>>>>
>>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>
>>>>>>
>>>>>
>>>>>
>>>>
>>>> --
>>>> Ben Greear <greearb@candelatech.com>
>>>> Candela Technologies Inc http://www.candelatech.com
>>>
>>>
>>
>> --
>> Ben Greear <greearb@candelatech.com>
>> Candela Technologies Inc http://www.candelatech.com
>> _______________________________________________
>> openwrt-devel mailing list
>> openwrt-devel@lists.openwrt.org
>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>
--
Ben Greear <greearb@candelatech.com>
Candela Technologies Inc http://www.candelatech.com
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 54+ messages in thread
* Re: [OpenWrt-Devel] ATH10K VLAN firmware issue
2016-11-04 22:23 ` Ben Greear
@ 2016-11-07 11:54 ` Bruno Antunes
-1 siblings, 0 replies; 54+ messages in thread
From: Bruno Antunes @ 2016-11-07 11:54 UTC (permalink / raw)
To: Ben Greear
Cc: yu-chieh kung, Mauro Mozzarelli, linux-wireless,
OpenWrt Development List, ath10k
On 4 November 2016 at 22:23, Ben Greear <greearb@candelatech.com> wrote:
> The bug appears that vlan-tx-stripping is unconditionally enabled in
> at least my firmware. I have re-compiled w/out that flag set, and it
> appears
> to work for me.
>
> Please download this firmware, rename it firmware-2.bin, make sure you
> remove/rename
> any firmware-5.bin (etc) so mine will load, and see if that fixes your
> problem.
Thanks for the fast reply but it only solves "half" the problem.
Now the connection between the AP and the Sta can be secure and the
driver doesn't need to be loaded in rawmode.
Unfortunatly the the throughput is still bad.
iperf3 -c 10.10.4.15
Connecting to host 10.10.4.15, port 5201
[ 4] local 10.10.4.16 port 44893 connected to 10.10.4.15 port 5201
[ ID] Interval Transfer Bandwidth Retr Cwnd
[ 4] 0.00-1.01 sec 42.4 KBytes 345 Kbits/sec 6 1.41 KBytes
[ 4] 1.01-2.01 sec 0.00 Bytes 0.00 bits/sec 1 1.41 KBytes
[ 4] 2.01-3.01 sec 0.00 Bytes 0.00 bits/sec 1 1.41 KBytes
[ 4] 3.01-4.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
[ 4] 4.01-5.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
[ 4] 5.01-6.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
[ 4] 6.01-7.01 sec 0.00 Bytes 0.00 bits/sec 1 1.41 KBytes
[ 4] 7.01-8.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
[ 4] 8.01-9.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
[ 4] 9.01-10.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bandwidth Retr
[ 4] 0.00-10.01 sec 42.4 KBytes 34.7 Kbits/sec 9 sender
[ 4] 0.00-10.01 sec 0.00 Bytes 0.00 bits/sec receiver
iperf Done.
>
> Please note that it is very likely you will have to use same MAC address
> for the VLAN devices that the underlying station uses in order for this to
> work.
Can you please elaborate more?
My setup is the folowing.
The connection between the AP and Sta is in WDS
For the moment all devices are in the same VLAN.
client1 --- SW1 ---- AP ...... Sta ---- SW2 --- client2
Thanks,
Bruno
>
> https://www.candelatech.com/downloads/tmp/firmware-2-full-community.bin
>
>
> Thanks,
> Ben
>
>
>
> Ben Greear <greearb@candelatech.com>
> Candela Technologies Inc http://www.candelatech.com
>
^ permalink raw reply [flat|nested] 54+ messages in thread
* Re: [OpenWrt-Devel] ATH10K VLAN firmware issue
@ 2016-11-07 11:54 ` Bruno Antunes
0 siblings, 0 replies; 54+ messages in thread
From: Bruno Antunes @ 2016-11-07 11:54 UTC (permalink / raw)
To: Ben Greear
Cc: Mauro Mozzarelli, linux-wireless, OpenWrt Development List,
ath10k, yu-chieh kung
On 4 November 2016 at 22:23, Ben Greear <greearb@candelatech.com> wrote:
> The bug appears that vlan-tx-stripping is unconditionally enabled in
> at least my firmware. I have re-compiled w/out that flag set, and it
> appears
> to work for me.
>
> Please download this firmware, rename it firmware-2.bin, make sure you
> remove/rename
> any firmware-5.bin (etc) so mine will load, and see if that fixes your
> problem.
Thanks for the fast reply but it only solves "half" the problem.
Now the connection between the AP and the Sta can be secure and the
driver doesn't need to be loaded in rawmode.
Unfortunatly the the throughput is still bad.
iperf3 -c 10.10.4.15
Connecting to host 10.10.4.15, port 5201
[ 4] local 10.10.4.16 port 44893 connected to 10.10.4.15 port 5201
[ ID] Interval Transfer Bandwidth Retr Cwnd
[ 4] 0.00-1.01 sec 42.4 KBytes 345 Kbits/sec 6 1.41 KBytes
[ 4] 1.01-2.01 sec 0.00 Bytes 0.00 bits/sec 1 1.41 KBytes
[ 4] 2.01-3.01 sec 0.00 Bytes 0.00 bits/sec 1 1.41 KBytes
[ 4] 3.01-4.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
[ 4] 4.01-5.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
[ 4] 5.01-6.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
[ 4] 6.01-7.01 sec 0.00 Bytes 0.00 bits/sec 1 1.41 KBytes
[ 4] 7.01-8.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
[ 4] 8.01-9.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
[ 4] 9.01-10.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bandwidth Retr
[ 4] 0.00-10.01 sec 42.4 KBytes 34.7 Kbits/sec 9 sender
[ 4] 0.00-10.01 sec 0.00 Bytes 0.00 bits/sec receiver
iperf Done.
>
> Please note that it is very likely you will have to use same MAC address
> for the VLAN devices that the underlying station uses in order for this to
> work.
Can you please elaborate more?
My setup is the folowing.
The connection between the AP and Sta is in WDS
For the moment all devices are in the same VLAN.
client1 --- SW1 ---- AP ...... Sta ---- SW2 --- client2
Thanks,
Bruno
>
> https://www.candelatech.com/downloads/tmp/firmware-2-full-community.bin
>
>
> Thanks,
> Ben
>
>
>
> Ben Greear <greearb@candelatech.com>
> Candela Technologies Inc http://www.candelatech.com
>
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 54+ messages in thread
* Re: [OpenWrt-Devel] ATH10K VLAN firmware issue
2016-11-07 11:54 ` Bruno Antunes
@ 2016-11-07 14:06 ` Ben Greear
-1 siblings, 0 replies; 54+ messages in thread
From: Ben Greear @ 2016-11-07 14:06 UTC (permalink / raw)
To: Bruno Antunes
Cc: yu-chieh kung, Mauro Mozzarelli, linux-wireless,
OpenWrt Development List, ath10k
On 11/07/2016 03:54 AM, Bruno Antunes wrote:
> On 4 November 2016 at 22:23, Ben Greear <greearb@candelatech.com> wrote:
>> The bug appears that vlan-tx-stripping is unconditionally enabled in
>> at least my firmware. I have re-compiled w/out that flag set, and it
>> appears
>> to work for me.
>>
>> Please download this firmware, rename it firmware-2.bin, make sure you
>> remove/rename
>> any firmware-5.bin (etc) so mine will load, and see if that fixes your
>> problem.
>
> Thanks for the fast reply but it only solves "half" the problem.
>
> Now the connection between the AP and the Sta can be secure and the
> driver doesn't need to be loaded in rawmode.
>
> Unfortunatly the the throughput is still bad.
>
> iperf3 -c 10.10.4.15
> Connecting to host 10.10.4.15, port 5201
> [ 4] local 10.10.4.16 port 44893 connected to 10.10.4.15 port 5201
> [ ID] Interval Transfer Bandwidth Retr Cwnd
> [ 4] 0.00-1.01 sec 42.4 KBytes 345 Kbits/sec 6 1.41 KBytes
> [ 4] 1.01-2.01 sec 0.00 Bytes 0.00 bits/sec 1 1.41 KBytes
> [ 4] 2.01-3.01 sec 0.00 Bytes 0.00 bits/sec 1 1.41 KBytes
> [ 4] 3.01-4.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
> [ 4] 4.01-5.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
> [ 4] 5.01-6.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
> [ 4] 6.01-7.01 sec 0.00 Bytes 0.00 bits/sec 1 1.41 KBytes
> [ 4] 7.01-8.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
> [ 4] 8.01-9.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
> [ 4] 9.01-10.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
> - - - - - - - - - - - - - - - - - - - - - - - - -
> [ ID] Interval Transfer Bandwidth Retr
> [ 4] 0.00-10.01 sec 42.4 KBytes 34.7 Kbits/sec 9 sender
> [ 4] 0.00-10.01 sec 0.00 Bytes 0.00 bits/sec receiver
You have a complex setup, so I think it would be best if you could break it into
simpler parts to test.
First, try just STA to AP, no vlans, and see if you get useful throughput.
Then try with VLANs
Then, try with WDS.
Then try with WDS and vlans.
In STA to AP mode with VLANs, it performed well for me.
Thanks,
Ben
>
> iperf Done.
>
>>
>> Please note that it is very likely you will have to use same MAC address
>> for the VLAN devices that the underlying station uses in order for this to
>> work.
>
> Can you please elaborate more?
> My setup is the folowing.
> The connection between the AP and Sta is in WDS
> For the moment all devices are in the same VLAN.
>
> client1 --- SW1 ---- AP ...... Sta ---- SW2 --- client2
>
>
> Thanks,
> Bruno
>
>>
>> https://www.candelatech.com/downloads/tmp/firmware-2-full-community.bin
>>
>>
>> Thanks,
>> Ben
>>
>>
>>
>
>> Ben Greear <greearb@candelatech.com>
>> Candela Technologies Inc http://www.candelatech.com
>>
>
--
Ben Greear <greearb@candelatech.com>
Candela Technologies Inc http://www.candelatech.com
^ permalink raw reply [flat|nested] 54+ messages in thread
* Re: [OpenWrt-Devel] ATH10K VLAN firmware issue
@ 2016-11-07 14:06 ` Ben Greear
0 siblings, 0 replies; 54+ messages in thread
From: Ben Greear @ 2016-11-07 14:06 UTC (permalink / raw)
To: Bruno Antunes
Cc: Mauro Mozzarelli, linux-wireless, OpenWrt Development List,
ath10k, yu-chieh kung
On 11/07/2016 03:54 AM, Bruno Antunes wrote:
> On 4 November 2016 at 22:23, Ben Greear <greearb@candelatech.com> wrote:
>> The bug appears that vlan-tx-stripping is unconditionally enabled in
>> at least my firmware. I have re-compiled w/out that flag set, and it
>> appears
>> to work for me.
>>
>> Please download this firmware, rename it firmware-2.bin, make sure you
>> remove/rename
>> any firmware-5.bin (etc) so mine will load, and see if that fixes your
>> problem.
>
> Thanks for the fast reply but it only solves "half" the problem.
>
> Now the connection between the AP and the Sta can be secure and the
> driver doesn't need to be loaded in rawmode.
>
> Unfortunatly the the throughput is still bad.
>
> iperf3 -c 10.10.4.15
> Connecting to host 10.10.4.15, port 5201
> [ 4] local 10.10.4.16 port 44893 connected to 10.10.4.15 port 5201
> [ ID] Interval Transfer Bandwidth Retr Cwnd
> [ 4] 0.00-1.01 sec 42.4 KBytes 345 Kbits/sec 6 1.41 KBytes
> [ 4] 1.01-2.01 sec 0.00 Bytes 0.00 bits/sec 1 1.41 KBytes
> [ 4] 2.01-3.01 sec 0.00 Bytes 0.00 bits/sec 1 1.41 KBytes
> [ 4] 3.01-4.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
> [ 4] 4.01-5.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
> [ 4] 5.01-6.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
> [ 4] 6.01-7.01 sec 0.00 Bytes 0.00 bits/sec 1 1.41 KBytes
> [ 4] 7.01-8.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
> [ 4] 8.01-9.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
> [ 4] 9.01-10.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
> - - - - - - - - - - - - - - - - - - - - - - - - -
> [ ID] Interval Transfer Bandwidth Retr
> [ 4] 0.00-10.01 sec 42.4 KBytes 34.7 Kbits/sec 9 sender
> [ 4] 0.00-10.01 sec 0.00 Bytes 0.00 bits/sec receiver
You have a complex setup, so I think it would be best if you could break it into
simpler parts to test.
First, try just STA to AP, no vlans, and see if you get useful throughput.
Then try with VLANs
Then, try with WDS.
Then try with WDS and vlans.
In STA to AP mode with VLANs, it performed well for me.
Thanks,
Ben
>
> iperf Done.
>
>>
>> Please note that it is very likely you will have to use same MAC address
>> for the VLAN devices that the underlying station uses in order for this to
>> work.
>
> Can you please elaborate more?
> My setup is the folowing.
> The connection between the AP and Sta is in WDS
> For the moment all devices are in the same VLAN.
>
> client1 --- SW1 ---- AP ...... Sta ---- SW2 --- client2
>
>
> Thanks,
> Bruno
>
>>
>> https://www.candelatech.com/downloads/tmp/firmware-2-full-community.bin
>>
>>
>> Thanks,
>> Ben
>>
>>
>>
>
>> Ben Greear <greearb@candelatech.com>
>> Candela Technologies Inc http://www.candelatech.com
>>
>
--
Ben Greear <greearb@candelatech.com>
Candela Technologies Inc http://www.candelatech.com
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 54+ messages in thread
* Re: [OpenWrt-Devel] ATH10K VLAN firmware issue
2016-11-07 14:06 ` Ben Greear
@ 2016-11-07 14:13 ` Bruno Antunes
-1 siblings, 0 replies; 54+ messages in thread
From: Bruno Antunes @ 2016-11-07 14:13 UTC (permalink / raw)
To: Ben Greear
Cc: yu-chieh kung, Mauro Mozzarelli, linux-wireless,
OpenWrt Development List, ath10k
On 7 November 2016 at 14:06, Ben Greear <greearb@candelatech.com> wrote:
> On 11/07/2016 03:54 AM, Bruno Antunes wrote:
>>
>> On 4 November 2016 at 22:23, Ben Greear <greearb@candelatech.com> wrote:
>>>
>>> The bug appears that vlan-tx-stripping is unconditionally enabled in
>>> at least my firmware. I have re-compiled w/out that flag set, and it
>>> appears
>>> to work for me.
>>>
>>> Please download this firmware, rename it firmware-2.bin, make sure you
>>> remove/rename
>>> any firmware-5.bin (etc) so mine will load, and see if that fixes your
>>> problem.
>>
>>
>> Thanks for the fast reply but it only solves "half" the problem.
>>
>> Now the connection between the AP and the Sta can be secure and the
>> driver doesn't need to be loaded in rawmode.
>>
>> Unfortunatly the the throughput is still bad.
>>
>> iperf3 -c 10.10.4.15
>> Connecting to host 10.10.4.15, port 5201
>> [ 4] local 10.10.4.16 port 44893 connected to 10.10.4.15 port 5201
>> [ ID] Interval Transfer Bandwidth Retr Cwnd
>> [ 4] 0.00-1.01 sec 42.4 KBytes 345 Kbits/sec 6 1.41 KBytes
>> [ 4] 1.01-2.01 sec 0.00 Bytes 0.00 bits/sec 1 1.41 KBytes
>> [ 4] 2.01-3.01 sec 0.00 Bytes 0.00 bits/sec 1 1.41 KBytes
>> [ 4] 3.01-4.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
>> [ 4] 4.01-5.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
>> [ 4] 5.01-6.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
>> [ 4] 6.01-7.01 sec 0.00 Bytes 0.00 bits/sec 1 1.41 KBytes
>> [ 4] 7.01-8.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
>> [ 4] 8.01-9.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
>> [ 4] 9.01-10.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
>> - - - - - - - - - - - - - - - - - - - - - - - - -
>> [ ID] Interval Transfer Bandwidth Retr
>> [ 4] 0.00-10.01 sec 42.4 KBytes 34.7 Kbits/sec 9
>> sender
>> [ 4] 0.00-10.01 sec 0.00 Bytes 0.00 bits/sec
>> receiver
>
>
> You have a complex setup, so I think it would be best if you could break it
> into
> simpler parts to test.
Some of the parts I already tested and are working
>
> First, try just STA to AP, no vlans, and see if you get useful throughput.
>
Works fine
> Then try with VLANs
>
To Do
> Then, try with WDS.
Works fine
>
> Then try with WDS and vlans.
>
The ultimate goal...
> In STA to AP mode with VLANs, it performed well for me.
>
> Thanks,
> Ben
>
>
>>
>> iperf Done.
>>
>>>
>>> Please note that it is very likely you will have to use same MAC address
>>> for the VLAN devices that the underlying station uses in order for this
>>> to
>>> work.
>>
>>
>> Can you please elaborate more?
>> My setup is the folowing.
>> The connection between the AP and Sta is in WDS
>> For the moment all devices are in the same VLAN.
>>
>> client1 --- SW1 ---- AP ...... Sta ---- SW2 --- client2
>>
>>
>> Thanks,
>> Bruno
>>
>>>
>>> https://www.candelatech.com/downloads/tmp/firmware-2-full-community.bin
>>>
>>>
>>> Thanks,
>>> Ben
>>>
>>>
>>>
>>
>>> Ben Greear <greearb@candelatech.com>
>>> Candela Technologies Inc http://www.candelatech.com
>>>
>>
>
> --
> Ben Greear <greearb@candelatech.com>
> Candela Technologies Inc http://www.candelatech.com
^ permalink raw reply [flat|nested] 54+ messages in thread
* Re: [OpenWrt-Devel] ATH10K VLAN firmware issue
@ 2016-11-07 14:13 ` Bruno Antunes
0 siblings, 0 replies; 54+ messages in thread
From: Bruno Antunes @ 2016-11-07 14:13 UTC (permalink / raw)
To: Ben Greear
Cc: Mauro Mozzarelli, linux-wireless, OpenWrt Development List,
ath10k, yu-chieh kung
On 7 November 2016 at 14:06, Ben Greear <greearb@candelatech.com> wrote:
> On 11/07/2016 03:54 AM, Bruno Antunes wrote:
>>
>> On 4 November 2016 at 22:23, Ben Greear <greearb@candelatech.com> wrote:
>>>
>>> The bug appears that vlan-tx-stripping is unconditionally enabled in
>>> at least my firmware. I have re-compiled w/out that flag set, and it
>>> appears
>>> to work for me.
>>>
>>> Please download this firmware, rename it firmware-2.bin, make sure you
>>> remove/rename
>>> any firmware-5.bin (etc) so mine will load, and see if that fixes your
>>> problem.
>>
>>
>> Thanks for the fast reply but it only solves "half" the problem.
>>
>> Now the connection between the AP and the Sta can be secure and the
>> driver doesn't need to be loaded in rawmode.
>>
>> Unfortunatly the the throughput is still bad.
>>
>> iperf3 -c 10.10.4.15
>> Connecting to host 10.10.4.15, port 5201
>> [ 4] local 10.10.4.16 port 44893 connected to 10.10.4.15 port 5201
>> [ ID] Interval Transfer Bandwidth Retr Cwnd
>> [ 4] 0.00-1.01 sec 42.4 KBytes 345 Kbits/sec 6 1.41 KBytes
>> [ 4] 1.01-2.01 sec 0.00 Bytes 0.00 bits/sec 1 1.41 KBytes
>> [ 4] 2.01-3.01 sec 0.00 Bytes 0.00 bits/sec 1 1.41 KBytes
>> [ 4] 3.01-4.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
>> [ 4] 4.01-5.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
>> [ 4] 5.01-6.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
>> [ 4] 6.01-7.01 sec 0.00 Bytes 0.00 bits/sec 1 1.41 KBytes
>> [ 4] 7.01-8.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
>> [ 4] 8.01-9.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
>> [ 4] 9.01-10.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
>> - - - - - - - - - - - - - - - - - - - - - - - - -
>> [ ID] Interval Transfer Bandwidth Retr
>> [ 4] 0.00-10.01 sec 42.4 KBytes 34.7 Kbits/sec 9
>> sender
>> [ 4] 0.00-10.01 sec 0.00 Bytes 0.00 bits/sec
>> receiver
>
>
> You have a complex setup, so I think it would be best if you could break it
> into
> simpler parts to test.
Some of the parts I already tested and are working
>
> First, try just STA to AP, no vlans, and see if you get useful throughput.
>
Works fine
> Then try with VLANs
>
To Do
> Then, try with WDS.
Works fine
>
> Then try with WDS and vlans.
>
The ultimate goal...
> In STA to AP mode with VLANs, it performed well for me.
>
> Thanks,
> Ben
>
>
>>
>> iperf Done.
>>
>>>
>>> Please note that it is very likely you will have to use same MAC address
>>> for the VLAN devices that the underlying station uses in order for this
>>> to
>>> work.
>>
>>
>> Can you please elaborate more?
>> My setup is the folowing.
>> The connection between the AP and Sta is in WDS
>> For the moment all devices are in the same VLAN.
>>
>> client1 --- SW1 ---- AP ...... Sta ---- SW2 --- client2
>>
>>
>> Thanks,
>> Bruno
>>
>>>
>>> https://www.candelatech.com/downloads/tmp/firmware-2-full-community.bin
>>>
>>>
>>> Thanks,
>>> Ben
>>>
>>>
>>>
>>
>>> Ben Greear <greearb@candelatech.com>
>>> Candela Technologies Inc http://www.candelatech.com
>>>
>>
>
> --
> Ben Greear <greearb@candelatech.com>
> Candela Technologies Inc http://www.candelatech.com
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 54+ messages in thread