Re: [PATCH v2 10/16] ASoC: qcom: audioreach: add bedai support

[Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>]

> +static int q6dma_hw_params(struct snd_pcm_substream *substream,
> +			   struct snd_pcm_hw_params *params,
> +			   struct snd_soc_dai *dai)
> +{
> +	struct q6apm_bedai_data *dai_data = dev_get_drvdata(dai->dev);
> +	struct q6apm_cdc_dma_cfg *cfg = &dai_data->port_config[dai->id].dma_cfg;
> +
> +	cfg->bit_width = params_width(params);
> +	cfg->sample_rate = params_rate(params);
> +	cfg->num_channels = params_channels(params);
> +
> +	switch (params_format(params)) {
> +	case SNDRV_PCM_FORMAT_S16_LE:
> +		dai_data->bits_per_sample[dai->id] = 16;
> +		break;
> +	case SNDRV_PCM_FORMAT_S24_LE:
> +		dai_data->bits_per_sample[dai->id] = 24;
> +		break;

default:
    return -EINVAL;

?

> +	}
> +
> +	return 0;
> +}
> +
> +static void q6apm_bedai_shutdown(struct snd_pcm_substream *substream,
> +				struct snd_soc_dai *dai)
> +{
> +	struct q6apm_bedai_data *dai_data = dev_get_drvdata(dai->dev);
> +	int rc;
> +
> +	if (!dai_data->is_port_started[dai->id])
> +		return;
> +	rc = q6apm_graph_stop(dai_data->graph[dai->id]);
> +	if (rc < 0)
> +		dev_err(dai->dev, "fail to close APM port (%d)\n", rc);
> +
> +	q6apm_graph_close(dai_data->graph[dai->id]);
> +	dai_data->is_port_started[dai->id] = false;

difficult to follow, this mixes '!start', 'stop', 'close'


> +
> +}
> +
> +static int q6apm_bedai_prepare(struct snd_pcm_substream *substream,
> +			       struct snd_soc_dai *dai)
> +{
> +	struct q6apm_bedai_data *dai_data = dev_get_drvdata(dai->dev);
> +	struct q6apm_cdc_dma_cfg *cfg = &dai_data->port_config[dai->id].dma_cfg;
> +	int graph_id = dai->id;
> +	int rc;
> +	int ret;
> +	struct q6apm_graph *graph;
> +
> +	if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) {
> +		graph = q6apm_graph_open(dai->dev, NULL, dai->dev, graph_id);
> +		if (IS_ERR(graph)) {
> +			dev_err(dai->dev, "Failed to open graph (%d)\n",
> +				graph_id);
> +			ret = PTR_ERR(graph);
> +			return ret;
> +		}
> +		dai_data->graph[graph_id] = graph;
> +	}
> +
> +	rc = q6apm_graph_media_format_pcm(dai_data->graph[dai->id],
> +					  substream->stream, cfg->sample_rate,
> +					  cfg->num_channels, NULL, cfg->bit_width);
> +
> +	rc = q6apm_graph_prepare(dai_data->graph[dai->id]);

any good static analyzer would tell you you didn't test rc before overriding it..

this looks rather questionable.

> +	rc = q6apm_graph_start(dai_data->graph[dai->id]);
> +	if (rc < 0) {
> +		dev_err(dai->dev, "fail to start APM port %x\n", dai->id);
> +		return rc;
> +	}
> +	dai_data->is_port_started[dai->id] = true;
> +
> +	return 0;
> +}