[PATCH v3 0/4] cpufreq: Add imx-cpufreq-dt driver

[PATCH v3 0/4] cpufreq: Add imx-cpufreq-dt driver

[Leonard Crestez]

Right now in upstream imx8m cpufreq support just lists a common subset
of OPPs because the higher ones should only be attempted after checking
speed grading in fuses.

Driver reads from nvmem and calls dev_pm_opp_set_supported_hw before
registering cpufreq-dt.

Changes since v2:
 * Minor reformatting in Kconfig (Viresh)
 * Open-code imx_cpufreq_dt_match_node (Viresh)
 * Add mkt_segment bits to supported_hw and update .dtsi to match after
reviewing latest datasheets.
 * Add dt-bindings like other opp-supported-hw users
 * Add devicetree mailing list (keep forgetting dts needs to be reviewed)
Link to v2: https://patchwork.kernel.org/project/linux-arm-kernel/list/?series=113163
Link to v1 (RFC): https://patchwork.kernel.org/patch/10916769/

I never noticed anything wrong with going above the fused speed grading
however it's technically unsafe so the cpufreq code changes should go in
before DT changes.

Driver is module by default. It depends on nvmem-imx which can also be a
module.

It's a platform device registered from soc-imx8 because couldn't find
any appropriate node for MODULE_DEVICE_TABLE(of).

Leonard Crestez (4):
  cpufreq: Add imx-cpufreq-dt driver
  dt-bindings: imx-cpufreq-dt: Document opp-supported-hw usage
  arm64: dts: imx8mm: Add cpu speed grading and all OPPs
  arm64: dts: imx8mq: Add cpu speed grading and all OPPs

 .../bindings/cpufreq/imx-cpufreq-dt.txt       | 37 +++++++
 arch/arm64/boot/dts/freescale/imx8mm.dtsi     | 17 +++-
 arch/arm64/boot/dts/freescale/imx8mq.dtsi     | 26 ++++-
 drivers/cpufreq/Kconfig.arm                   | 10 ++
 drivers/cpufreq/Makefile                      |  1 +
 drivers/cpufreq/cpufreq-dt-platdev.c          |  3 +
 drivers/cpufreq/imx-cpufreq-dt.c              | 96 +++++++++++++++++++
 drivers/soc/imx/soc-imx8.c                    |  3 +
 8 files changed, 191 insertions(+), 2 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/cpufreq/imx-cpufreq-dt.txt
 create mode 100644 drivers/cpufreq/imx-cpufreq-dt.c

-- 
2.17.1

[PATCH v3 0/4] cpufreq: Add imx-cpufreq-dt driver

[Leonard Crestez]

Right now in upstream imx8m cpufreq support just lists a common subset
of OPPs because the higher ones should only be attempted after checking
speed grading in fuses.

Driver reads from nvmem and calls dev_pm_opp_set_supported_hw before
registering cpufreq-dt.

Changes since v2:
 * Minor reformatting in Kconfig (Viresh)
 * Open-code imx_cpufreq_dt_match_node (Viresh)
 * Add mkt_segment bits to supported_hw and update .dtsi to match after
reviewing latest datasheets.
 * Add dt-bindings like other opp-supported-hw users
 * Add devicetree mailing list (keep forgetting dts needs to be reviewed)
Link to v2: https://patchwork.kernel.org/project/linux-arm-kernel/list/?series=113163
Link to v1 (RFC): https://patchwork.kernel.org/patch/10916769/

I never noticed anything wrong with going above the fused speed grading
however it's technically unsafe so the cpufreq code changes should go in
before DT changes.

Driver is module by default. It depends on nvmem-imx which can also be a
module.

It's a platform device registered from soc-imx8 because couldn't find
any appropriate node for MODULE_DEVICE_TABLE(of).

Leonard Crestez (4):
  cpufreq: Add imx-cpufreq-dt driver
  dt-bindings: imx-cpufreq-dt: Document opp-supported-hw usage
  arm64: dts: imx8mm: Add cpu speed grading and all OPPs
  arm64: dts: imx8mq: Add cpu speed grading and all OPPs

 .../bindings/cpufreq/imx-cpufreq-dt.txt       | 37 +++++++
 arch/arm64/boot/dts/freescale/imx8mm.dtsi     | 17 +++-
 arch/arm64/boot/dts/freescale/imx8mq.dtsi     | 26 ++++-
 drivers/cpufreq/Kconfig.arm                   | 10 ++
 drivers/cpufreq/Makefile                      |  1 +
 drivers/cpufreq/cpufreq-dt-platdev.c          |  3 +
 drivers/cpufreq/imx-cpufreq-dt.c              | 96 +++++++++++++++++++
 drivers/soc/imx/soc-imx8.c                    |  3 +
 8 files changed, 191 insertions(+), 2 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/cpufreq/imx-cpufreq-dt.txt
 create mode 100644 drivers/cpufreq/imx-cpufreq-dt.c

-- 
2.17.1

[PATCH v3 0/4] cpufreq: Add imx-cpufreq-dt driver

[Leonard Crestez]

Right now in upstream imx8m cpufreq support just lists a common subset
of OPPs because the higher ones should only be attempted after checking
speed grading in fuses.

Driver reads from nvmem and calls dev_pm_opp_set_supported_hw before
registering cpufreq-dt.

Changes since v2:
 * Minor reformatting in Kconfig (Viresh)
 * Open-code imx_cpufreq_dt_match_node (Viresh)
 * Add mkt_segment bits to supported_hw and update .dtsi to match after
reviewing latest datasheets.
 * Add dt-bindings like other opp-supported-hw users
 * Add devicetree mailing list (keep forgetting dts needs to be reviewed)
Link to v2: https://patchwork.kernel.org/project/linux-arm-kernel/list/?series=113163
Link to v1 (RFC): https://patchwork.kernel.org/patch/10916769/

I never noticed anything wrong with going above the fused speed grading
however it's technically unsafe so the cpufreq code changes should go in
before DT changes.

Driver is module by default. It depends on nvmem-imx which can also be a
module.

It's a platform device registered from soc-imx8 because couldn't find
any appropriate node for MODULE_DEVICE_TABLE(of).

Leonard Crestez (4):
  cpufreq: Add imx-cpufreq-dt driver
  dt-bindings: imx-cpufreq-dt: Document opp-supported-hw usage
  arm64: dts: imx8mm: Add cpu speed grading and all OPPs
  arm64: dts: imx8mq: Add cpu speed grading and all OPPs

 .../bindings/cpufreq/imx-cpufreq-dt.txt       | 37 +++++++
 arch/arm64/boot/dts/freescale/imx8mm.dtsi     | 17 +++-
 arch/arm64/boot/dts/freescale/imx8mq.dtsi     | 26 ++++-
 drivers/cpufreq/Kconfig.arm                   | 10 ++
 drivers/cpufreq/Makefile                      |  1 +
 drivers/cpufreq/cpufreq-dt-platdev.c          |  3 +
 drivers/cpufreq/imx-cpufreq-dt.c              | 96 +++++++++++++++++++
 drivers/soc/imx/soc-imx8.c                    |  3 +
 8 files changed, 191 insertions(+), 2 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/cpufreq/imx-cpufreq-dt.txt
 create mode 100644 drivers/cpufreq/imx-cpufreq-dt.c

-- 
2.17.1

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 1/4] cpufreq: Add imx-cpufreq-dt driver

[Leonard Crestez]

Right now in upstream imx8m cpufreq support just lists a common subset
of OPPs because the higher ones should only be attempted after checking
speed grading in fuses.

Add a small driver which checks speed grading from nvmem cells before
registering cpufreq-dt.

This driver allows unlocking all frequencies for imx8mm and imx8mq and
could be applied to other chips like imx7d

Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>

---
 drivers/cpufreq/Kconfig.arm          | 10 +++
 drivers/cpufreq/Makefile             |  1 +
 drivers/cpufreq/cpufreq-dt-platdev.c |  3 +
 drivers/cpufreq/imx-cpufreq-dt.c     | 96 ++++++++++++++++++++++++++++
 drivers/soc/imx/soc-imx8.c           |  3 +
 5 files changed, 113 insertions(+)
 create mode 100644 drivers/cpufreq/imx-cpufreq-dt.c

diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm
index 179a1d302f48..78ed9ef49e68 100644
--- a/drivers/cpufreq/Kconfig.arm
+++ b/drivers/cpufreq/Kconfig.arm
@@ -90,10 +90,20 @@ config ARM_IMX6Q_CPUFREQ
 	help
 	  This adds cpufreq driver support for Freescale i.MX6 series SoCs.
 
 	  If in doubt, say N.
 
+config ARM_IMX_CPUFREQ_DT
+	tristate "Freescale i.MX8M cpufreq support"
+	depends on ARCH_MXC && CPUFREQ_DT
+	default m if ARCH_MXC && CPUFREQ_DT
+	help
+	  This adds cpufreq driver support for Freescale i.MX8M series SoCs,
+	  based on cpufreq-dt.
+
+	  If in doubt, say N.
+
 config ARM_KIRKWOOD_CPUFREQ
 	def_bool MACH_KIRKWOOD
 	help
 	  This adds the CPUFreq driver for Marvell Kirkwood
 	  SoCs.
diff --git a/drivers/cpufreq/Makefile b/drivers/cpufreq/Makefile
index 689b26c6f949..7bcda2273d0c 100644
--- a/drivers/cpufreq/Makefile
+++ b/drivers/cpufreq/Makefile
@@ -54,10 +54,11 @@ obj-$(CONFIG_ARM_ARMADA_8K_CPUFREQ)	+= armada-8k-cpufreq.o
 obj-$(CONFIG_ARM_BRCMSTB_AVS_CPUFREQ)	+= brcmstb-avs-cpufreq.o
 obj-$(CONFIG_ACPI_CPPC_CPUFREQ)		+= cppc_cpufreq.o
 obj-$(CONFIG_ARCH_DAVINCI)		+= davinci-cpufreq.o
 obj-$(CONFIG_ARM_HIGHBANK_CPUFREQ)	+= highbank-cpufreq.o
 obj-$(CONFIG_ARM_IMX6Q_CPUFREQ)		+= imx6q-cpufreq.o
+obj-$(CONFIG_ARM_IMX_CPUFREQ_DT)	+= imx-cpufreq-dt.o
 obj-$(CONFIG_ARM_KIRKWOOD_CPUFREQ)	+= kirkwood-cpufreq.o
 obj-$(CONFIG_ARM_MEDIATEK_CPUFREQ)	+= mediatek-cpufreq.o
 obj-$(CONFIG_MACH_MVEBU_V7)		+= mvebu-cpufreq.o
 obj-$(CONFIG_ARM_OMAP2PLUS_CPUFREQ)	+= omap-cpufreq.o
 obj-$(CONFIG_ARM_PXA2xx_CPUFREQ)	+= pxa2xx-cpufreq.o
diff --git a/drivers/cpufreq/cpufreq-dt-platdev.c b/drivers/cpufreq/cpufreq-dt-platdev.c
index 47729a22c159..19c1aad57e26 100644
--- a/drivers/cpufreq/cpufreq-dt-platdev.c
+++ b/drivers/cpufreq/cpufreq-dt-platdev.c
@@ -106,10 +106,13 @@ static const struct of_device_id whitelist[] __initconst = {
  */
 static const struct of_device_id blacklist[] __initconst = {
 	{ .compatible = "calxeda,highbank", },
 	{ .compatible = "calxeda,ecx-2000", },
 
+	{ .compatible = "fsl,imx8mq", },
+	{ .compatible = "fsl,imx8mm", },
+
 	{ .compatible = "marvell,armadaxp", },
 
 	{ .compatible = "mediatek,mt2701", },
 	{ .compatible = "mediatek,mt2712", },
 	{ .compatible = "mediatek,mt7622", },
diff --git a/drivers/cpufreq/imx-cpufreq-dt.c b/drivers/cpufreq/imx-cpufreq-dt.c
new file mode 100644
index 000000000000..e1aa346efa10
--- /dev/null
+++ b/drivers/cpufreq/imx-cpufreq-dt.c
@@ -0,0 +1,96 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2019 NXP
+ */
+
+#include <linux/cpu.h>
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/nvmem-consumer.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pm_opp.h>
+#include <linux/slab.h>
+
+#define OCOTP_CFG3_SPEED_GRADE_SHIFT	8
+#define OCOTP_CFG3_SPEED_GRADE_MASK	(0x3 << 8)
+#define OCOTP_CFG3_MKT_SEGMENT_SHIFT    6
+#define OCOTP_CFG3_MKT_SEGMENT_MASK     (0x3 << 6)
+
+static const struct of_device_id imx_cpufreq_dt_match_list[] = {
+	{ .compatible = "fsl,imx8mm" },
+	{ .compatible = "fsl,imx8mq" },
+	{}
+};
+
+/* cpufreq-dt device registered by imx-cpufreq-dt */
+static struct platform_device *cpufreq_dt_pdev;
+static struct opp_table *cpufreq_opp_table;
+
+static int imx_cpufreq_dt_probe(struct platform_device *pdev)
+{
+	struct device *cpu_dev = get_cpu_device(0);
+	struct device_node *np;
+	const struct of_device_id *match;
+	u32 cell_value, supported_hw[2];
+	int speed_grade, mkt_segment;
+	int ret;
+
+	np = of_find_node_by_path("/");
+	match = of_match_node(imx_cpufreq_dt_match_list, np);
+	of_node_put(np);
+	if (!match)
+		return -ENODEV;
+
+	ret = nvmem_cell_read_u32(cpu_dev, "speed_grade", &cell_value);
+	if (ret)
+		return ret;
+
+	speed_grade = (cell_value & OCOTP_CFG3_SPEED_GRADE_MASK) >> OCOTP_CFG3_SPEED_GRADE_SHIFT;
+	mkt_segment = (cell_value & OCOTP_CFG3_MKT_SEGMENT_MASK) >> OCOTP_CFG3_MKT_SEGMENT_SHIFT;
+	supported_hw[0] = BIT(speed_grade);
+	supported_hw[1] = BIT(mkt_segment);
+	dev_info(&pdev->dev, "cpu speed grade %d mkt segment %d supported-hw %#x %#x\n",
+			speed_grade, mkt_segment, supported_hw[0], supported_hw[1]);
+
+	cpufreq_opp_table = dev_pm_opp_set_supported_hw(cpu_dev, supported_hw, 2);
+	if (IS_ERR(cpufreq_opp_table)) {
+		ret = PTR_ERR(cpufreq_opp_table);
+		dev_err(&pdev->dev, "Failed to set supported opp: %d\n", ret);
+		return ret;
+	}
+
+	cpufreq_dt_pdev = platform_device_register_data(
+			&pdev->dev, "cpufreq-dt", -1, NULL, 0);
+	if (IS_ERR(cpufreq_dt_pdev)) {
+		dev_pm_opp_put_supported_hw(cpufreq_opp_table);
+		ret = PTR_ERR(cpufreq_dt_pdev);
+		dev_err(&pdev->dev, "Failed to register cpufreq-dt: %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int imx_cpufreq_dt_remove(struct platform_device *pdev)
+{
+	platform_device_unregister(cpufreq_dt_pdev);
+	dev_pm_opp_put_supported_hw(cpufreq_opp_table);
+
+	return 0;
+}
+
+static struct platform_driver imx_cpufreq_dt_driver = {
+	.probe = imx_cpufreq_dt_probe,
+	.remove = imx_cpufreq_dt_remove,
+	.driver = {
+		.name = "imx-cpufreq-dt",
+	},
+};
+module_platform_driver(imx_cpufreq_dt_driver);
+
+MODULE_ALIAS("platform:imx-cpufreq-dt");
+MODULE_DESCRIPTION("Freescale i.MX cpufreq speed grading driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/soc/imx/soc-imx8.c b/drivers/soc/imx/soc-imx8.c
index cd10726e64e4..02988bdfbb73 100644
--- a/drivers/soc/imx/soc-imx8.c
+++ b/drivers/soc/imx/soc-imx8.c
@@ -130,10 +130,13 @@ static int __init imx8_soc_init(void)
 
 	soc_dev = soc_device_register(soc_dev_attr);
 	if (IS_ERR(soc_dev))
 		goto free_rev;
 
+	if (IS_ENABLED(CONFIG_ARM_IMX_CPUFREQ_DT))
+		platform_device_register_simple("imx-cpufreq-dt", -1, NULL, 0);
+
 	return 0;
 
 free_rev:
 	kfree(soc_dev_attr->revision);
 free_soc:
-- 
2.17.1

[PATCH v3 1/4] cpufreq: Add imx-cpufreq-dt driver

[Leonard Crestez]

Right now in upstream imx8m cpufreq support just lists a common subset
of OPPs because the higher ones should only be attempted after checking
speed grading in fuses.

Add a small driver which checks speed grading from nvmem cells before
registering cpufreq-dt.

This driver allows unlocking all frequencies for imx8mm and imx8mq and
could be applied to other chips like imx7d

Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>

---
 drivers/cpufreq/Kconfig.arm          | 10 +++
 drivers/cpufreq/Makefile             |  1 +
 drivers/cpufreq/cpufreq-dt-platdev.c |  3 +
 drivers/cpufreq/imx-cpufreq-dt.c     | 96 ++++++++++++++++++++++++++++
 drivers/soc/imx/soc-imx8.c           |  3 +
 5 files changed, 113 insertions(+)
 create mode 100644 drivers/cpufreq/imx-cpufreq-dt.c

diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm
index 179a1d302f48..78ed9ef49e68 100644
--- a/drivers/cpufreq/Kconfig.arm
+++ b/drivers/cpufreq/Kconfig.arm
@@ -90,10 +90,20 @@ config ARM_IMX6Q_CPUFREQ
 	help
 	  This adds cpufreq driver support for Freescale i.MX6 series SoCs.
 
 	  If in doubt, say N.
 
+config ARM_IMX_CPUFREQ_DT
+	tristate "Freescale i.MX8M cpufreq support"
+	depends on ARCH_MXC && CPUFREQ_DT
+	default m if ARCH_MXC && CPUFREQ_DT
+	help
+	  This adds cpufreq driver support for Freescale i.MX8M series SoCs,
+	  based on cpufreq-dt.
+
+	  If in doubt, say N.
+
 config ARM_KIRKWOOD_CPUFREQ
 	def_bool MACH_KIRKWOOD
 	help
 	  This adds the CPUFreq driver for Marvell Kirkwood
 	  SoCs.
diff --git a/drivers/cpufreq/Makefile b/drivers/cpufreq/Makefile
index 689b26c6f949..7bcda2273d0c 100644
--- a/drivers/cpufreq/Makefile
+++ b/drivers/cpufreq/Makefile
@@ -54,10 +54,11 @@ obj-$(CONFIG_ARM_ARMADA_8K_CPUFREQ)	+= armada-8k-cpufreq.o
 obj-$(CONFIG_ARM_BRCMSTB_AVS_CPUFREQ)	+= brcmstb-avs-cpufreq.o
 obj-$(CONFIG_ACPI_CPPC_CPUFREQ)		+= cppc_cpufreq.o
 obj-$(CONFIG_ARCH_DAVINCI)		+= davinci-cpufreq.o
 obj-$(CONFIG_ARM_HIGHBANK_CPUFREQ)	+= highbank-cpufreq.o
 obj-$(CONFIG_ARM_IMX6Q_CPUFREQ)		+= imx6q-cpufreq.o
+obj-$(CONFIG_ARM_IMX_CPUFREQ_DT)	+= imx-cpufreq-dt.o
 obj-$(CONFIG_ARM_KIRKWOOD_CPUFREQ)	+= kirkwood-cpufreq.o
 obj-$(CONFIG_ARM_MEDIATEK_CPUFREQ)	+= mediatek-cpufreq.o
 obj-$(CONFIG_MACH_MVEBU_V7)		+= mvebu-cpufreq.o
 obj-$(CONFIG_ARM_OMAP2PLUS_CPUFREQ)	+= omap-cpufreq.o
 obj-$(CONFIG_ARM_PXA2xx_CPUFREQ)	+= pxa2xx-cpufreq.o
diff --git a/drivers/cpufreq/cpufreq-dt-platdev.c b/drivers/cpufreq/cpufreq-dt-platdev.c
index 47729a22c159..19c1aad57e26 100644
--- a/drivers/cpufreq/cpufreq-dt-platdev.c
+++ b/drivers/cpufreq/cpufreq-dt-platdev.c
@@ -106,10 +106,13 @@ static const struct of_device_id whitelist[] __initconst = {
  */
 static const struct of_device_id blacklist[] __initconst = {
 	{ .compatible = "calxeda,highbank", },
 	{ .compatible = "calxeda,ecx-2000", },
 
+	{ .compatible = "fsl,imx8mq", },
+	{ .compatible = "fsl,imx8mm", },
+
 	{ .compatible = "marvell,armadaxp", },
 
 	{ .compatible = "mediatek,mt2701", },
 	{ .compatible = "mediatek,mt2712", },
 	{ .compatible = "mediatek,mt7622", },
diff --git a/drivers/cpufreq/imx-cpufreq-dt.c b/drivers/cpufreq/imx-cpufreq-dt.c
new file mode 100644
index 000000000000..e1aa346efa10
--- /dev/null
+++ b/drivers/cpufreq/imx-cpufreq-dt.c
@@ -0,0 +1,96 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2019 NXP
+ */
+
+#include <linux/cpu.h>
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/nvmem-consumer.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pm_opp.h>
+#include <linux/slab.h>
+
+#define OCOTP_CFG3_SPEED_GRADE_SHIFT	8
+#define OCOTP_CFG3_SPEED_GRADE_MASK	(0x3 << 8)
+#define OCOTP_CFG3_MKT_SEGMENT_SHIFT    6
+#define OCOTP_CFG3_MKT_SEGMENT_MASK     (0x3 << 6)
+
+static const struct of_device_id imx_cpufreq_dt_match_list[] = {
+	{ .compatible = "fsl,imx8mm" },
+	{ .compatible = "fsl,imx8mq" },
+	{}
+};
+
+/* cpufreq-dt device registered by imx-cpufreq-dt */
+static struct platform_device *cpufreq_dt_pdev;
+static struct opp_table *cpufreq_opp_table;
+
+static int imx_cpufreq_dt_probe(struct platform_device *pdev)
+{
+	struct device *cpu_dev = get_cpu_device(0);
+	struct device_node *np;
+	const struct of_device_id *match;
+	u32 cell_value, supported_hw[2];
+	int speed_grade, mkt_segment;
+	int ret;
+
+	np = of_find_node_by_path("/");
+	match = of_match_node(imx_cpufreq_dt_match_list, np);
+	of_node_put(np);
+	if (!match)
+		return -ENODEV;
+
+	ret = nvmem_cell_read_u32(cpu_dev, "speed_grade", &cell_value);
+	if (ret)
+		return ret;
+
+	speed_grade = (cell_value & OCOTP_CFG3_SPEED_GRADE_MASK) >> OCOTP_CFG3_SPEED_GRADE_SHIFT;
+	mkt_segment = (cell_value & OCOTP_CFG3_MKT_SEGMENT_MASK) >> OCOTP_CFG3_MKT_SEGMENT_SHIFT;
+	supported_hw[0] = BIT(speed_grade);
+	supported_hw[1] = BIT(mkt_segment);
+	dev_info(&pdev->dev, "cpu speed grade %d mkt segment %d supported-hw %#x %#x\n",
+			speed_grade, mkt_segment, supported_hw[0], supported_hw[1]);
+
+	cpufreq_opp_table = dev_pm_opp_set_supported_hw(cpu_dev, supported_hw, 2);
+	if (IS_ERR(cpufreq_opp_table)) {
+		ret = PTR_ERR(cpufreq_opp_table);
+		dev_err(&pdev->dev, "Failed to set supported opp: %d\n", ret);
+		return ret;
+	}
+
+	cpufreq_dt_pdev = platform_device_register_data(
+			&pdev->dev, "cpufreq-dt", -1, NULL, 0);
+	if (IS_ERR(cpufreq_dt_pdev)) {
+		dev_pm_opp_put_supported_hw(cpufreq_opp_table);
+		ret = PTR_ERR(cpufreq_dt_pdev);
+		dev_err(&pdev->dev, "Failed to register cpufreq-dt: %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int imx_cpufreq_dt_remove(struct platform_device *pdev)
+{
+	platform_device_unregister(cpufreq_dt_pdev);
+	dev_pm_opp_put_supported_hw(cpufreq_opp_table);
+
+	return 0;
+}
+
+static struct platform_driver imx_cpufreq_dt_driver = {
+	.probe = imx_cpufreq_dt_probe,
+	.remove = imx_cpufreq_dt_remove,
+	.driver = {
+		.name = "imx-cpufreq-dt",
+	},
+};
+module_platform_driver(imx_cpufreq_dt_driver);
+
+MODULE_ALIAS("platform:imx-cpufreq-dt");
+MODULE_DESCRIPTION("Freescale i.MX cpufreq speed grading driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/soc/imx/soc-imx8.c b/drivers/soc/imx/soc-imx8.c
index cd10726e64e4..02988bdfbb73 100644
--- a/drivers/soc/imx/soc-imx8.c
+++ b/drivers/soc/imx/soc-imx8.c
@@ -130,10 +130,13 @@ static int __init imx8_soc_init(void)
 
 	soc_dev = soc_device_register(soc_dev_attr);
 	if (IS_ERR(soc_dev))
 		goto free_rev;
 
+	if (IS_ENABLED(CONFIG_ARM_IMX_CPUFREQ_DT))
+		platform_device_register_simple("imx-cpufreq-dt", -1, NULL, 0);
+
 	return 0;
 
 free_rev:
 	kfree(soc_dev_attr->revision);
 free_soc:
-- 
2.17.1

[PATCH v3 1/4] cpufreq: Add imx-cpufreq-dt driver

[Leonard Crestez]

Right now in upstream imx8m cpufreq support just lists a common subset
of OPPs because the higher ones should only be attempted after checking
speed grading in fuses.

Add a small driver which checks speed grading from nvmem cells before
registering cpufreq-dt.

This driver allows unlocking all frequencies for imx8mm and imx8mq and
could be applied to other chips like imx7d

Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>

---
 drivers/cpufreq/Kconfig.arm          | 10 +++
 drivers/cpufreq/Makefile             |  1 +
 drivers/cpufreq/cpufreq-dt-platdev.c |  3 +
 drivers/cpufreq/imx-cpufreq-dt.c     | 96 ++++++++++++++++++++++++++++
 drivers/soc/imx/soc-imx8.c           |  3 +
 5 files changed, 113 insertions(+)
 create mode 100644 drivers/cpufreq/imx-cpufreq-dt.c

diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm
index 179a1d302f48..78ed9ef49e68 100644
--- a/drivers/cpufreq/Kconfig.arm
+++ b/drivers/cpufreq/Kconfig.arm
@@ -90,10 +90,20 @@ config ARM_IMX6Q_CPUFREQ
 	help
 	  This adds cpufreq driver support for Freescale i.MX6 series SoCs.
 
 	  If in doubt, say N.
 
+config ARM_IMX_CPUFREQ_DT
+	tristate "Freescale i.MX8M cpufreq support"
+	depends on ARCH_MXC && CPUFREQ_DT
+	default m if ARCH_MXC && CPUFREQ_DT
+	help
+	  This adds cpufreq driver support for Freescale i.MX8M series SoCs,
+	  based on cpufreq-dt.
+
+	  If in doubt, say N.
+
 config ARM_KIRKWOOD_CPUFREQ
 	def_bool MACH_KIRKWOOD
 	help
 	  This adds the CPUFreq driver for Marvell Kirkwood
 	  SoCs.
diff --git a/drivers/cpufreq/Makefile b/drivers/cpufreq/Makefile
index 689b26c6f949..7bcda2273d0c 100644
--- a/drivers/cpufreq/Makefile
+++ b/drivers/cpufreq/Makefile
@@ -54,10 +54,11 @@ obj-$(CONFIG_ARM_ARMADA_8K_CPUFREQ)	+= armada-8k-cpufreq.o
 obj-$(CONFIG_ARM_BRCMSTB_AVS_CPUFREQ)	+= brcmstb-avs-cpufreq.o
 obj-$(CONFIG_ACPI_CPPC_CPUFREQ)		+= cppc_cpufreq.o
 obj-$(CONFIG_ARCH_DAVINCI)		+= davinci-cpufreq.o
 obj-$(CONFIG_ARM_HIGHBANK_CPUFREQ)	+= highbank-cpufreq.o
 obj-$(CONFIG_ARM_IMX6Q_CPUFREQ)		+= imx6q-cpufreq.o
+obj-$(CONFIG_ARM_IMX_CPUFREQ_DT)	+= imx-cpufreq-dt.o
 obj-$(CONFIG_ARM_KIRKWOOD_CPUFREQ)	+= kirkwood-cpufreq.o
 obj-$(CONFIG_ARM_MEDIATEK_CPUFREQ)	+= mediatek-cpufreq.o
 obj-$(CONFIG_MACH_MVEBU_V7)		+= mvebu-cpufreq.o
 obj-$(CONFIG_ARM_OMAP2PLUS_CPUFREQ)	+= omap-cpufreq.o
 obj-$(CONFIG_ARM_PXA2xx_CPUFREQ)	+= pxa2xx-cpufreq.o
diff --git a/drivers/cpufreq/cpufreq-dt-platdev.c b/drivers/cpufreq/cpufreq-dt-platdev.c
index 47729a22c159..19c1aad57e26 100644
--- a/drivers/cpufreq/cpufreq-dt-platdev.c
+++ b/drivers/cpufreq/cpufreq-dt-platdev.c
@@ -106,10 +106,13 @@ static const struct of_device_id whitelist[] __initconst = {
  */
 static const struct of_device_id blacklist[] __initconst = {
 	{ .compatible = "calxeda,highbank", },
 	{ .compatible = "calxeda,ecx-2000", },
 
+	{ .compatible = "fsl,imx8mq", },
+	{ .compatible = "fsl,imx8mm", },
+
 	{ .compatible = "marvell,armadaxp", },
 
 	{ .compatible = "mediatek,mt2701", },
 	{ .compatible = "mediatek,mt2712", },
 	{ .compatible = "mediatek,mt7622", },
diff --git a/drivers/cpufreq/imx-cpufreq-dt.c b/drivers/cpufreq/imx-cpufreq-dt.c
new file mode 100644
index 000000000000..e1aa346efa10
--- /dev/null
+++ b/drivers/cpufreq/imx-cpufreq-dt.c
@@ -0,0 +1,96 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2019 NXP
+ */
+
+#include <linux/cpu.h>
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/nvmem-consumer.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pm_opp.h>
+#include <linux/slab.h>
+
+#define OCOTP_CFG3_SPEED_GRADE_SHIFT	8
+#define OCOTP_CFG3_SPEED_GRADE_MASK	(0x3 << 8)
+#define OCOTP_CFG3_MKT_SEGMENT_SHIFT    6
+#define OCOTP_CFG3_MKT_SEGMENT_MASK     (0x3 << 6)
+
+static const struct of_device_id imx_cpufreq_dt_match_list[] = {
+	{ .compatible = "fsl,imx8mm" },
+	{ .compatible = "fsl,imx8mq" },
+	{}
+};
+
+/* cpufreq-dt device registered by imx-cpufreq-dt */
+static struct platform_device *cpufreq_dt_pdev;
+static struct opp_table *cpufreq_opp_table;
+
+static int imx_cpufreq_dt_probe(struct platform_device *pdev)
+{
+	struct device *cpu_dev = get_cpu_device(0);
+	struct device_node *np;
+	const struct of_device_id *match;
+	u32 cell_value, supported_hw[2];
+	int speed_grade, mkt_segment;
+	int ret;
+
+	np = of_find_node_by_path("/");
+	match = of_match_node(imx_cpufreq_dt_match_list, np);
+	of_node_put(np);
+	if (!match)
+		return -ENODEV;
+
+	ret = nvmem_cell_read_u32(cpu_dev, "speed_grade", &cell_value);
+	if (ret)
+		return ret;
+
+	speed_grade = (cell_value & OCOTP_CFG3_SPEED_GRADE_MASK) >> OCOTP_CFG3_SPEED_GRADE_SHIFT;
+	mkt_segment = (cell_value & OCOTP_CFG3_MKT_SEGMENT_MASK) >> OCOTP_CFG3_MKT_SEGMENT_SHIFT;
+	supported_hw[0] = BIT(speed_grade);
+	supported_hw[1] = BIT(mkt_segment);
+	dev_info(&pdev->dev, "cpu speed grade %d mkt segment %d supported-hw %#x %#x\n",
+			speed_grade, mkt_segment, supported_hw[0], supported_hw[1]);
+
+	cpufreq_opp_table = dev_pm_opp_set_supported_hw(cpu_dev, supported_hw, 2);
+	if (IS_ERR(cpufreq_opp_table)) {
+		ret = PTR_ERR(cpufreq_opp_table);
+		dev_err(&pdev->dev, "Failed to set supported opp: %d\n", ret);
+		return ret;
+	}
+
+	cpufreq_dt_pdev = platform_device_register_data(
+			&pdev->dev, "cpufreq-dt", -1, NULL, 0);
+	if (IS_ERR(cpufreq_dt_pdev)) {
+		dev_pm_opp_put_supported_hw(cpufreq_opp_table);
+		ret = PTR_ERR(cpufreq_dt_pdev);
+		dev_err(&pdev->dev, "Failed to register cpufreq-dt: %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int imx_cpufreq_dt_remove(struct platform_device *pdev)
+{
+	platform_device_unregister(cpufreq_dt_pdev);
+	dev_pm_opp_put_supported_hw(cpufreq_opp_table);
+
+	return 0;
+}
+
+static struct platform_driver imx_cpufreq_dt_driver = {
+	.probe = imx_cpufreq_dt_probe,
+	.remove = imx_cpufreq_dt_remove,
+	.driver = {
+		.name = "imx-cpufreq-dt",
+	},
+};
+module_platform_driver(imx_cpufreq_dt_driver);
+
+MODULE_ALIAS("platform:imx-cpufreq-dt");
+MODULE_DESCRIPTION("Freescale i.MX cpufreq speed grading driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/soc/imx/soc-imx8.c b/drivers/soc/imx/soc-imx8.c
index cd10726e64e4..02988bdfbb73 100644
--- a/drivers/soc/imx/soc-imx8.c
+++ b/drivers/soc/imx/soc-imx8.c
@@ -130,10 +130,13 @@ static int __init imx8_soc_init(void)
 
 	soc_dev = soc_device_register(soc_dev_attr);
 	if (IS_ERR(soc_dev))
 		goto free_rev;
 
+	if (IS_ENABLED(CONFIG_ARM_IMX_CPUFREQ_DT))
+		platform_device_register_simple("imx-cpufreq-dt", -1, NULL, 0);
+
 	return 0;
 
 free_rev:
 	kfree(soc_dev_attr->revision);
 free_soc:
-- 
2.17.1

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 2/4] dt-bindings: imx-cpufreq-dt: Document opp-supported-hw usage

[Leonard Crestez]

The interpretation of opp-supported-hw bits for imx-cpufreq-dt driver is
not very obvious so attempt to explain it.

There is no OF compat string associated.

Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
---
 .../bindings/cpufreq/imx-cpufreq-dt.txt       | 37 +++++++++++++++++++
 1 file changed, 37 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/cpufreq/imx-cpufreq-dt.txt

diff --git a/Documentation/devicetree/bindings/cpufreq/imx-cpufreq-dt.txt b/Documentation/devicetree/bindings/cpufreq/imx-cpufreq-dt.txt
new file mode 100644
index 000000000000..87bff5add3f9
--- /dev/null
+++ b/Documentation/devicetree/bindings/cpufreq/imx-cpufreq-dt.txt
@@ -0,0 +1,37 @@
+i.MX CPUFreq-DT OPP bindings
+================================
+
+Certain i.MX SoCs support different OPPs depending on the "market segment" and
+"speed grading" value which are written in fuses. These bits are combined with
+the opp-supported-hw values for each OPP to check if the OPP is allowed.
+
+Required properties:
+--------------------
+
+For each opp entry in 'operating-points-v2' table:
+- opp-supported-hw: Two bitmaps indicating:
+  - Supported speed grade mask
+  - Supported market segment mask
+    0: Consumer
+    1: Extended Consumer
+    2: Industrial
+    3: Automotive
+
+Example:
+--------
+
+opp_table {
+	compatible = "operating-points-v2";
+	opp-1000000000 {
+		opp-hz = /bits/ 64 <1000000000>;
+		/* grade >= 0, consumer only */
+		opp-supported-hw = <0xf>, <0x3>;
+	};
+
+	opp-1300000000 {
+		opp-hz = /bits/ 64 <1300000000>;
+		opp-microvolt = <1000000>;
+		/* grade >= 1, all segments */
+		opp-supported-hw = <0xe>, <0x7>;
+	};
+}
-- 
2.17.1

[PATCH v3 2/4] dt-bindings: imx-cpufreq-dt: Document opp-supported-hw usage

[Leonard Crestez]

The interpretation of opp-supported-hw bits for imx-cpufreq-dt driver is
not very obvious so attempt to explain it.

There is no OF compat string associated.

Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
---
 .../bindings/cpufreq/imx-cpufreq-dt.txt       | 37 +++++++++++++++++++
 1 file changed, 37 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/cpufreq/imx-cpufreq-dt.txt

diff --git a/Documentation/devicetree/bindings/cpufreq/imx-cpufreq-dt.txt b/Documentation/devicetree/bindings/cpufreq/imx-cpufreq-dt.txt
new file mode 100644
index 000000000000..87bff5add3f9
--- /dev/null
+++ b/Documentation/devicetree/bindings/cpufreq/imx-cpufreq-dt.txt
@@ -0,0 +1,37 @@
+i.MX CPUFreq-DT OPP bindings
+================================
+
+Certain i.MX SoCs support different OPPs depending on the "market segment" and
+"speed grading" value which are written in fuses. These bits are combined with
+the opp-supported-hw values for each OPP to check if the OPP is allowed.
+
+Required properties:
+--------------------
+
+For each opp entry in 'operating-points-v2' table:
+- opp-supported-hw: Two bitmaps indicating:
+  - Supported speed grade mask
+  - Supported market segment mask
+    0: Consumer
+    1: Extended Consumer
+    2: Industrial
+    3: Automotive
+
+Example:
+--------
+
+opp_table {
+	compatible = "operating-points-v2";
+	opp-1000000000 {
+		opp-hz = /bits/ 64 <1000000000>;
+		/* grade >= 0, consumer only */
+		opp-supported-hw = <0xf>, <0x3>;
+	};
+
+	opp-1300000000 {
+		opp-hz = /bits/ 64 <1300000000>;
+		opp-microvolt = <1000000>;
+		/* grade >= 1, all segments */
+		opp-supported-hw = <0xe>, <0x7>;
+	};
+}
-- 
2.17.1

[PATCH v3 2/4] dt-bindings: imx-cpufreq-dt: Document opp-supported-hw usage

[Leonard Crestez]

The interpretation of opp-supported-hw bits for imx-cpufreq-dt driver is
not very obvious so attempt to explain it.

There is no OF compat string associated.

Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
---
 .../bindings/cpufreq/imx-cpufreq-dt.txt       | 37 +++++++++++++++++++
 1 file changed, 37 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/cpufreq/imx-cpufreq-dt.txt

diff --git a/Documentation/devicetree/bindings/cpufreq/imx-cpufreq-dt.txt b/Documentation/devicetree/bindings/cpufreq/imx-cpufreq-dt.txt
new file mode 100644
index 000000000000..87bff5add3f9
--- /dev/null
+++ b/Documentation/devicetree/bindings/cpufreq/imx-cpufreq-dt.txt
@@ -0,0 +1,37 @@
+i.MX CPUFreq-DT OPP bindings
+================================
+
+Certain i.MX SoCs support different OPPs depending on the "market segment" and
+"speed grading" value which are written in fuses. These bits are combined with
+the opp-supported-hw values for each OPP to check if the OPP is allowed.
+
+Required properties:
+--------------------
+
+For each opp entry in 'operating-points-v2' table:
+- opp-supported-hw: Two bitmaps indicating:
+  - Supported speed grade mask
+  - Supported market segment mask
+    0: Consumer
+    1: Extended Consumer
+    2: Industrial
+    3: Automotive
+
+Example:
+--------
+
+opp_table {
+	compatible = "operating-points-v2";
+	opp-1000000000 {
+		opp-hz = /bits/ 64 <1000000000>;
+		/* grade >= 0, consumer only */
+		opp-supported-hw = <0xf>, <0x3>;
+	};
+
+	opp-1300000000 {
+		opp-hz = /bits/ 64 <1300000000>;
+		opp-microvolt = <1000000>;
+		/* grade >= 1, all segments */
+		opp-supported-hw = <0xe>, <0x7>;
+	};
+}
-- 
2.17.1

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 3/4] arm64: dts: imx8mm: Add cpu speed grading and all OPPs

[Leonard Crestez]

Add a nvmem cell on cpu node referencing speed grade and the 1.8 Ghz
cpufreq opp.

Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
---
 arch/arm64/boot/dts/freescale/imx8mm.dtsi | 17 ++++++++++++++++-
 1 file changed, 16 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm.dtsi b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
index 0b2a585c5844..7eea47584f31 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
@@ -51,10 +51,12 @@
 			clock-latency = <61036>; /* two CLK32 periods */
 			clocks = <&clk IMX8MM_CLK_ARM>;
 			enable-method = "psci";
 			next-level-cache = <&A53_L2>;
 			operating-points-v2 = <&a53_opp_table>;
+			nvmem-cells = <&cpu_speed_grade>;
+			nvmem-cell-names = "speed_grade";
 		};
 
 		A53_1: cpu@1 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a53";
@@ -98,18 +100,27 @@
 		opp-shared;
 
 		opp-1200000000 {
 			opp-hz = /bits/ 64 <1200000000>;
 			opp-microvolt = <850000>;
+			opp-supported-hw = <0xe>, <0x7>;
 			clock-latency-ns = <150000>;
 		};
 
 		opp-1600000000 {
 			opp-hz = /bits/ 64 <1600000000>;
 			opp-microvolt = <900000>;
+			opp-supported-hw = <0xc>, <0x7>;
+			clock-latency-ns = <150000>;
+		};
+
+		opp-1800000000 {
+			opp-hz = /bits/ 64 <1800000000>;
+			opp-microvolt = <1000000>;
+			/* Consumer only but rely on speed grading */
+			opp-supported-hw = <0x8>, <0x7>;
 			clock-latency-ns = <150000>;
-			opp-suspend;
 		};
 	};
 
 	memory@40000000 {
 		device_type = "memory";
@@ -317,10 +328,14 @@
 				reg = <0x30350000 0x10000>;
 				clocks = <&clk IMX8MM_CLK_OCOTP_ROOT>;
 				/* For nvmem subnodes */
 				#address-cells = <1>;
 				#size-cells = <1>;
+
+				cpu_speed_grade: speed-grade@10 {
+					reg = <0x10 4>;
+				};
 			};
 
 			anatop: anatop@30360000 {
 				compatible = "fsl,imx8mm-anatop", "syscon", "simple-bus";
 				reg = <0x30360000 0x10000>;
-- 
2.17.1

[PATCH v3 3/4] arm64: dts: imx8mm: Add cpu speed grading and all OPPs

[Leonard Crestez]

Add a nvmem cell on cpu node referencing speed grade and the 1.8 Ghz
cpufreq opp.

Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
---
 arch/arm64/boot/dts/freescale/imx8mm.dtsi | 17 ++++++++++++++++-
 1 file changed, 16 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm.dtsi b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
index 0b2a585c5844..7eea47584f31 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
@@ -51,10 +51,12 @@
 			clock-latency = <61036>; /* two CLK32 periods */
 			clocks = <&clk IMX8MM_CLK_ARM>;
 			enable-method = "psci";
 			next-level-cache = <&A53_L2>;
 			operating-points-v2 = <&a53_opp_table>;
+			nvmem-cells = <&cpu_speed_grade>;
+			nvmem-cell-names = "speed_grade";
 		};
 
 		A53_1: cpu@1 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a53";
@@ -98,18 +100,27 @@
 		opp-shared;
 
 		opp-1200000000 {
 			opp-hz = /bits/ 64 <1200000000>;
 			opp-microvolt = <850000>;
+			opp-supported-hw = <0xe>, <0x7>;
 			clock-latency-ns = <150000>;
 		};
 
 		opp-1600000000 {
 			opp-hz = /bits/ 64 <1600000000>;
 			opp-microvolt = <900000>;
+			opp-supported-hw = <0xc>, <0x7>;
+			clock-latency-ns = <150000>;
+		};
+
+		opp-1800000000 {
+			opp-hz = /bits/ 64 <1800000000>;
+			opp-microvolt = <1000000>;
+			/* Consumer only but rely on speed grading */
+			opp-supported-hw = <0x8>, <0x7>;
 			clock-latency-ns = <150000>;
-			opp-suspend;
 		};
 	};
 
 	memory@40000000 {
 		device_type = "memory";
@@ -317,10 +328,14 @@
 				reg = <0x30350000 0x10000>;
 				clocks = <&clk IMX8MM_CLK_OCOTP_ROOT>;
 				/* For nvmem subnodes */
 				#address-cells = <1>;
 				#size-cells = <1>;
+
+				cpu_speed_grade: speed-grade@10 {
+					reg = <0x10 4>;
+				};
 			};
 
 			anatop: anatop@30360000 {
 				compatible = "fsl,imx8mm-anatop", "syscon", "simple-bus";
 				reg = <0x30360000 0x10000>;
-- 
2.17.1

[PATCH v3 3/4] arm64: dts: imx8mm: Add cpu speed grading and all OPPs

[Leonard Crestez]

Add a nvmem cell on cpu node referencing speed grade and the 1.8 Ghz
cpufreq opp.

Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
---
 arch/arm64/boot/dts/freescale/imx8mm.dtsi | 17 ++++++++++++++++-
 1 file changed, 16 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm.dtsi b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
index 0b2a585c5844..7eea47584f31 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
@@ -51,10 +51,12 @@
 			clock-latency = <61036>; /* two CLK32 periods */
 			clocks = <&clk IMX8MM_CLK_ARM>;
 			enable-method = "psci";
 			next-level-cache = <&A53_L2>;
 			operating-points-v2 = <&a53_opp_table>;
+			nvmem-cells = <&cpu_speed_grade>;
+			nvmem-cell-names = "speed_grade";
 		};
 
 		A53_1: cpu@1 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a53";
@@ -98,18 +100,27 @@
 		opp-shared;
 
 		opp-1200000000 {
 			opp-hz = /bits/ 64 <1200000000>;
 			opp-microvolt = <850000>;
+			opp-supported-hw = <0xe>, <0x7>;
 			clock-latency-ns = <150000>;
 		};
 
 		opp-1600000000 {
 			opp-hz = /bits/ 64 <1600000000>;
 			opp-microvolt = <900000>;
+			opp-supported-hw = <0xc>, <0x7>;
+			clock-latency-ns = <150000>;
+		};
+
+		opp-1800000000 {
+			opp-hz = /bits/ 64 <1800000000>;
+			opp-microvolt = <1000000>;
+			/* Consumer only but rely on speed grading */
+			opp-supported-hw = <0x8>, <0x7>;
 			clock-latency-ns = <150000>;
-			opp-suspend;
 		};
 	};
 
 	memory@40000000 {
 		device_type = "memory";
@@ -317,10 +328,14 @@
 				reg = <0x30350000 0x10000>;
 				clocks = <&clk IMX8MM_CLK_OCOTP_ROOT>;
 				/* For nvmem subnodes */
 				#address-cells = <1>;
 				#size-cells = <1>;
+
+				cpu_speed_grade: speed-grade@10 {
+					reg = <0x10 4>;
+				};
 			};
 
 			anatop: anatop@30360000 {
 				compatible = "fsl,imx8mm-anatop", "syscon", "simple-bus";
 				reg = <0x30360000 0x10000>;
-- 
2.17.1

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 4/4] arm64: dts: imx8mq: Add cpu speed grading and all OPPs

[Leonard Crestez]

Add nvmem-cells reference to cpu and fill the OPP table with all known
OPPs.

Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
---
 arch/arm64/boot/dts/freescale/imx8mq.dtsi | 26 ++++++++++++++++++++++-
 1 file changed, 25 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
index 6d635ba0904c..729376919d08 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
@@ -93,10 +93,12 @@
 			clocks = <&clk IMX8MQ_CLK_ARM>;
 			enable-method = "psci";
 			next-level-cache = <&A53_L2>;
 			operating-points-v2 = <&a53_opp_table>;
 			#cooling-cells = <2>;
+			nvmem-cells = <&cpu_speed_grade>;
+			nvmem-cell-names = "speed_grade";
 		};
 
 		A53_1: cpu@1 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a53";
@@ -143,18 +145,36 @@
 		opp-shared;
 
 		opp-800000000 {
 			opp-hz = /bits/ 64 <800000000>;
 			opp-microvolt = <900000>;
+			/* Industrial only */
+			opp-supported-hw = <0xf>, <0x4>;
+			clock-latency-ns = <150000>;
+		};
+
+		opp-1000000000 {
+			opp-hz = /bits/ 64 <1000000000>;
+			opp-microvolt = <900000>;
+			/* Consumer only */
+			opp-supported-hw = <0xe>, <0x3>;
 			clock-latency-ns = <150000>;
 		};
 
 		opp-1300000000 {
 			opp-hz = /bits/ 64 <1300000000>;
 			opp-microvolt = <1000000>;
+			opp-supported-hw = <0xc>, <0x7>;
+			clock-latency-ns = <150000>;
+		};
+
+		opp-1500000000 {
+			opp-hz = /bits/ 64 <1500000000>;
+			opp-microvolt = <1000000>;
+			/* Consumer only but rely on speed grading */
+			opp-supported-hw = <0x8>, <0x7>;
 			clock-latency-ns = <150000>;
-			opp-suspend;
 		};
 	};
 
 	pmu {
 		compatible = "arm,cortex-a53-pmu";
@@ -413,10 +433,14 @@
 				compatible = "fsl,imx8mq-ocotp", "syscon";
 				reg = <0x30350000 0x10000>;
 				clocks = <&clk IMX8MQ_CLK_OCOTP_ROOT>;
 				#address-cells = <1>;
 				#size-cells = <1>;
+
+				cpu_speed_grade: speed-grade@10 {
+					reg = <0x10 4>;
+				};
 			};
 
 			anatop: syscon@30360000 {
 				compatible = "fsl,imx8mq-anatop", "syscon";
 				reg = <0x30360000 0x10000>;
-- 
2.17.1

[PATCH v3 4/4] arm64: dts: imx8mq: Add cpu speed grading and all OPPs

[Leonard Crestez]

Add nvmem-cells reference to cpu and fill the OPP table with all known
OPPs.

Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
---
 arch/arm64/boot/dts/freescale/imx8mq.dtsi | 26 ++++++++++++++++++++++-
 1 file changed, 25 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
index 6d635ba0904c..729376919d08 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
@@ -93,10 +93,12 @@
 			clocks = <&clk IMX8MQ_CLK_ARM>;
 			enable-method = "psci";
 			next-level-cache = <&A53_L2>;
 			operating-points-v2 = <&a53_opp_table>;
 			#cooling-cells = <2>;
+			nvmem-cells = <&cpu_speed_grade>;
+			nvmem-cell-names = "speed_grade";
 		};
 
 		A53_1: cpu@1 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a53";
@@ -143,18 +145,36 @@
 		opp-shared;
 
 		opp-800000000 {
 			opp-hz = /bits/ 64 <800000000>;
 			opp-microvolt = <900000>;
+			/* Industrial only */
+			opp-supported-hw = <0xf>, <0x4>;
+			clock-latency-ns = <150000>;
+		};
+
+		opp-1000000000 {
+			opp-hz = /bits/ 64 <1000000000>;
+			opp-microvolt = <900000>;
+			/* Consumer only */
+			opp-supported-hw = <0xe>, <0x3>;
 			clock-latency-ns = <150000>;
 		};
 
 		opp-1300000000 {
 			opp-hz = /bits/ 64 <1300000000>;
 			opp-microvolt = <1000000>;
+			opp-supported-hw = <0xc>, <0x7>;
+			clock-latency-ns = <150000>;
+		};
+
+		opp-1500000000 {
+			opp-hz = /bits/ 64 <1500000000>;
+			opp-microvolt = <1000000>;
+			/* Consumer only but rely on speed grading */
+			opp-supported-hw = <0x8>, <0x7>;
 			clock-latency-ns = <150000>;
-			opp-suspend;
 		};
 	};
 
 	pmu {
 		compatible = "arm,cortex-a53-pmu";
@@ -413,10 +433,14 @@
 				compatible = "fsl,imx8mq-ocotp", "syscon";
 				reg = <0x30350000 0x10000>;
 				clocks = <&clk IMX8MQ_CLK_OCOTP_ROOT>;
 				#address-cells = <1>;
 				#size-cells = <1>;
+
+				cpu_speed_grade: speed-grade@10 {
+					reg = <0x10 4>;
+				};
 			};
 
 			anatop: syscon@30360000 {
 				compatible = "fsl,imx8mq-anatop", "syscon";
 				reg = <0x30360000 0x10000>;
-- 
2.17.1

[PATCH v3 4/4] arm64: dts: imx8mq: Add cpu speed grading and all OPPs

[Leonard Crestez]

Add nvmem-cells reference to cpu and fill the OPP table with all known
OPPs.

Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
---
 arch/arm64/boot/dts/freescale/imx8mq.dtsi | 26 ++++++++++++++++++++++-
 1 file changed, 25 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
index 6d635ba0904c..729376919d08 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
@@ -93,10 +93,12 @@
 			clocks = <&clk IMX8MQ_CLK_ARM>;
 			enable-method = "psci";
 			next-level-cache = <&A53_L2>;
 			operating-points-v2 = <&a53_opp_table>;
 			#cooling-cells = <2>;
+			nvmem-cells = <&cpu_speed_grade>;
+			nvmem-cell-names = "speed_grade";
 		};
 
 		A53_1: cpu@1 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a53";
@@ -143,18 +145,36 @@
 		opp-shared;
 
 		opp-800000000 {
 			opp-hz = /bits/ 64 <800000000>;
 			opp-microvolt = <900000>;
+			/* Industrial only */
+			opp-supported-hw = <0xf>, <0x4>;
+			clock-latency-ns = <150000>;
+		};
+
+		opp-1000000000 {
+			opp-hz = /bits/ 64 <1000000000>;
+			opp-microvolt = <900000>;
+			/* Consumer only */
+			opp-supported-hw = <0xe>, <0x3>;
 			clock-latency-ns = <150000>;
 		};
 
 		opp-1300000000 {
 			opp-hz = /bits/ 64 <1300000000>;
 			opp-microvolt = <1000000>;
+			opp-supported-hw = <0xc>, <0x7>;
+			clock-latency-ns = <150000>;
+		};
+
+		opp-1500000000 {
+			opp-hz = /bits/ 64 <1500000000>;
+			opp-microvolt = <1000000>;
+			/* Consumer only but rely on speed grading */
+			opp-supported-hw = <0x8>, <0x7>;
 			clock-latency-ns = <150000>;
-			opp-suspend;
 		};
 	};
 
 	pmu {
 		compatible = "arm,cortex-a53-pmu";
@@ -413,10 +433,14 @@
 				compatible = "fsl,imx8mq-ocotp", "syscon";
 				reg = <0x30350000 0x10000>;
 				clocks = <&clk IMX8MQ_CLK_OCOTP_ROOT>;
 				#address-cells = <1>;
 				#size-cells = <1>;
+
+				cpu_speed_grade: speed-grade@10 {
+					reg = <0x10 4>;
+				};
 			};
 
 			anatop: syscon@30360000 {
 				compatible = "fsl,imx8mq-anatop", "syscon";
 				reg = <0x30360000 0x10000>;
-- 
2.17.1

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 1/4] cpufreq: Add imx-cpufreq-dt driver

[Viresh Kumar]

On 07-05-19, 13:52, Leonard Crestez wrote:
> Right now in upstream imx8m cpufreq support just lists a common subset
> of OPPs because the higher ones should only be attempted after checking
> speed grading in fuses.
> 
> Add a small driver which checks speed grading from nvmem cells before
> registering cpufreq-dt.
> 
> This driver allows unlocking all frequencies for imx8mm and imx8mq and
> could be applied to other chips like imx7d
> 
> Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
> 
> ---
>  drivers/cpufreq/Kconfig.arm          | 10 +++
>  drivers/cpufreq/Makefile             |  1 +
>  drivers/cpufreq/cpufreq-dt-platdev.c |  3 +
>  drivers/cpufreq/imx-cpufreq-dt.c     | 96 ++++++++++++++++++++++++++++
>  drivers/soc/imx/soc-imx8.c           |  3 +
>  5 files changed, 113 insertions(+)
>  create mode 100644 drivers/cpufreq/imx-cpufreq-dt.c
> 
> diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm
> index 179a1d302f48..78ed9ef49e68 100644
> --- a/drivers/cpufreq/Kconfig.arm
> +++ b/drivers/cpufreq/Kconfig.arm
> @@ -90,10 +90,20 @@ config ARM_IMX6Q_CPUFREQ
>  	help
>  	  This adds cpufreq driver support for Freescale i.MX6 series SoCs.
>  
>  	  If in doubt, say N.
>  
> +config ARM_IMX_CPUFREQ_DT
> +	tristate "Freescale i.MX8M cpufreq support"
> +	depends on ARCH_MXC && CPUFREQ_DT
> +	default m if ARCH_MXC && CPUFREQ_DT

As I said in the previous version, the if block above is redundant and
not required.

> +	help
> +	  This adds cpufreq driver support for Freescale i.MX8M series SoCs,
> +	  based on cpufreq-dt.
> +
> +	  If in doubt, say N.

-- 
viresh

Re: [PATCH v3 1/4] cpufreq: Add imx-cpufreq-dt driver

[Viresh Kumar]

On 07-05-19, 13:52, Leonard Crestez wrote:
> Right now in upstream imx8m cpufreq support just lists a common subset
> of OPPs because the higher ones should only be attempted after checking
> speed grading in fuses.
> 
> Add a small driver which checks speed grading from nvmem cells before
> registering cpufreq-dt.
> 
> This driver allows unlocking all frequencies for imx8mm and imx8mq and
> could be applied to other chips like imx7d
> 
> Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
> 
> ---
>  drivers/cpufreq/Kconfig.arm          | 10 +++
>  drivers/cpufreq/Makefile             |  1 +
>  drivers/cpufreq/cpufreq-dt-platdev.c |  3 +
>  drivers/cpufreq/imx-cpufreq-dt.c     | 96 ++++++++++++++++++++++++++++
>  drivers/soc/imx/soc-imx8.c           |  3 +
>  5 files changed, 113 insertions(+)
>  create mode 100644 drivers/cpufreq/imx-cpufreq-dt.c
> 
> diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm
> index 179a1d302f48..78ed9ef49e68 100644
> --- a/drivers/cpufreq/Kconfig.arm
> +++ b/drivers/cpufreq/Kconfig.arm
> @@ -90,10 +90,20 @@ config ARM_IMX6Q_CPUFREQ
>  	help
>  	  This adds cpufreq driver support for Freescale i.MX6 series SoCs.
>  
>  	  If in doubt, say N.
>  
> +config ARM_IMX_CPUFREQ_DT
> +	tristate "Freescale i.MX8M cpufreq support"
> +	depends on ARCH_MXC && CPUFREQ_DT
> +	default m if ARCH_MXC && CPUFREQ_DT

As I said in the previous version, the if block above is redundant and
not required.

> +	help
> +	  This adds cpufreq driver support for Freescale i.MX8M series SoCs,
> +	  based on cpufreq-dt.
> +
> +	  If in doubt, say N.

-- 
viresh

Re: [PATCH v3 1/4] cpufreq: Add imx-cpufreq-dt driver

[Viresh Kumar]

On 07-05-19, 13:52, Leonard Crestez wrote:
> Right now in upstream imx8m cpufreq support just lists a common subset
> of OPPs because the higher ones should only be attempted after checking
> speed grading in fuses.
> 
> Add a small driver which checks speed grading from nvmem cells before
> registering cpufreq-dt.
> 
> This driver allows unlocking all frequencies for imx8mm and imx8mq and
> could be applied to other chips like imx7d
> 
> Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
> 
> ---
>  drivers/cpufreq/Kconfig.arm          | 10 +++
>  drivers/cpufreq/Makefile             |  1 +
>  drivers/cpufreq/cpufreq-dt-platdev.c |  3 +
>  drivers/cpufreq/imx-cpufreq-dt.c     | 96 ++++++++++++++++++++++++++++
>  drivers/soc/imx/soc-imx8.c           |  3 +
>  5 files changed, 113 insertions(+)
>  create mode 100644 drivers/cpufreq/imx-cpufreq-dt.c
> 
> diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm
> index 179a1d302f48..78ed9ef49e68 100644
> --- a/drivers/cpufreq/Kconfig.arm
> +++ b/drivers/cpufreq/Kconfig.arm
> @@ -90,10 +90,20 @@ config ARM_IMX6Q_CPUFREQ
>  	help
>  	  This adds cpufreq driver support for Freescale i.MX6 series SoCs.
>  
>  	  If in doubt, say N.
>  
> +config ARM_IMX_CPUFREQ_DT
> +	tristate "Freescale i.MX8M cpufreq support"
> +	depends on ARCH_MXC && CPUFREQ_DT
> +	default m if ARCH_MXC && CPUFREQ_DT

As I said in the previous version, the if block above is redundant and
not required.

> +	help
> +	  This adds cpufreq driver support for Freescale i.MX8M series SoCs,
> +	  based on cpufreq-dt.
> +
> +	  If in doubt, say N.

-- 
viresh

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 1/4] cpufreq: Add imx-cpufreq-dt driver

[Leonard Crestez]

On 5/8/2019 6:54 AM, Viresh Kumar wrote:
> On 07-05-19, 13:52, Leonard Crestez wrote:

>> +config ARM_IMX_CPUFREQ_DT
>> +	tristate "Freescale i.MX8M cpufreq support"
>> +	depends on ARCH_MXC && CPUFREQ_DT
>> +	default m if ARCH_MXC && CPUFREQ_DT
> 
> As I said in the previous version, the if block above is redundant and
> not required.

Sorry, I misread and thought you were referring to () rather than what's 
inside.

Is "default m" otherwise OK? It's a reasonable implication of ARCH_MXC

--
Regards,
Leonard

Re: [PATCH v3 1/4] cpufreq: Add imx-cpufreq-dt driver

[Leonard Crestez]

On 5/8/2019 6:54 AM, Viresh Kumar wrote:
> On 07-05-19, 13:52, Leonard Crestez wrote:

>> +config ARM_IMX_CPUFREQ_DT
>> +	tristate "Freescale i.MX8M cpufreq support"
>> +	depends on ARCH_MXC && CPUFREQ_DT
>> +	default m if ARCH_MXC && CPUFREQ_DT
> 
> As I said in the previous version, the if block above is redundant and
> not required.

Sorry, I misread and thought you were referring to () rather than what's 
inside.

Is "default m" otherwise OK? It's a reasonable implication of ARCH_MXC

--
Regards,
Leonard

Re: [PATCH v3 1/4] cpufreq: Add imx-cpufreq-dt driver

[Leonard Crestez]

On 5/8/2019 6:54 AM, Viresh Kumar wrote:
> On 07-05-19, 13:52, Leonard Crestez wrote:

>> +config ARM_IMX_CPUFREQ_DT
>> +	tristate "Freescale i.MX8M cpufreq support"
>> +	depends on ARCH_MXC && CPUFREQ_DT
>> +	default m if ARCH_MXC && CPUFREQ_DT
> 
> As I said in the previous version, the if block above is redundant and
> not required.

Sorry, I misread and thought you were referring to () rather than what's 
inside.

Is "default m" otherwise OK? It's a reasonable implication of ARCH_MXC

--
Regards,
Leonard

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 1/4] cpufreq: Add imx-cpufreq-dt driver

[Viresh Kumar]

On 09-05-19, 09:03, Leonard Crestez wrote:
> On 5/8/2019 6:54 AM, Viresh Kumar wrote:
> > On 07-05-19, 13:52, Leonard Crestez wrote:
> 
> >> +config ARM_IMX_CPUFREQ_DT
> >> +	tristate "Freescale i.MX8M cpufreq support"
> >> +	depends on ARCH_MXC && CPUFREQ_DT
> >> +	default m if ARCH_MXC && CPUFREQ_DT
> > 
> > As I said in the previous version, the if block above is redundant and
> > not required.
> 
> Sorry, I misread and thought you were referring to () rather than what's 
> inside.
> 
> Is "default m" otherwise OK? It's a reasonable implication of ARCH_MXC

I think it would be better to keep it disabled by default and so
removing the line all together would be a good option.

-- 
viresh

Re: [PATCH v3 1/4] cpufreq: Add imx-cpufreq-dt driver

[Viresh Kumar]

On 09-05-19, 09:03, Leonard Crestez wrote:
> On 5/8/2019 6:54 AM, Viresh Kumar wrote:
> > On 07-05-19, 13:52, Leonard Crestez wrote:
> 
> >> +config ARM_IMX_CPUFREQ_DT
> >> +	tristate "Freescale i.MX8M cpufreq support"
> >> +	depends on ARCH_MXC && CPUFREQ_DT
> >> +	default m if ARCH_MXC && CPUFREQ_DT
> > 
> > As I said in the previous version, the if block above is redundant and
> > not required.
> 
> Sorry, I misread and thought you were referring to () rather than what's 
> inside.
> 
> Is "default m" otherwise OK? It's a reasonable implication of ARCH_MXC

I think it would be better to keep it disabled by default and so
removing the line all together would be a good option.

-- 
viresh

Re: [PATCH v3 1/4] cpufreq: Add imx-cpufreq-dt driver

[Viresh Kumar]

On 09-05-19, 09:03, Leonard Crestez wrote:
> On 5/8/2019 6:54 AM, Viresh Kumar wrote:
> > On 07-05-19, 13:52, Leonard Crestez wrote:
> 
> >> +config ARM_IMX_CPUFREQ_DT
> >> +	tristate "Freescale i.MX8M cpufreq support"
> >> +	depends on ARCH_MXC && CPUFREQ_DT
> >> +	default m if ARCH_MXC && CPUFREQ_DT
> > 
> > As I said in the previous version, the if block above is redundant and
> > not required.
> 
> Sorry, I misread and thought you were referring to () rather than what's 
> inside.
> 
> Is "default m" otherwise OK? It's a reasonable implication of ARCH_MXC

I think it would be better to keep it disabled by default and so
removing the line all together would be a good option.

-- 
viresh

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel