* [PATCH V2 00/22] ARM: dts: stm32: Repair AV96 board
@ 2020-03-31 0:56 Marek Vasut
2020-03-31 0:56 ` [PATCH V2 01/22] ARM: dts: stm32: Add alternate pinmux for ethernet RGMII Marek Vasut
` (22 more replies)
0 siblings, 23 replies; 46+ messages in thread
From: Marek Vasut @ 2020-03-31 0:56 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Marek Vasut, Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, Manivannan Sadhasivam, linux-stm32
The AV96 board device tree is completely broken and does not match the
hardware. This series fixes it up.
Marek Vasut (22):
ARM: dts: stm32: Add alternate pinmux for ethernet RGMII
ARM: dts: stm32: Repair ethernet operation on AV96
ARM: dts: stm32: Add missing ethernet PHY reset on AV96
ARM: dts: stm32: Add missing ethernet PHY skews on AV96
ARM: dts: stm32: Add alternate pinmux for SDMMC1 direction pins
ARM: dts: stm32: Repair SDMMC1 operation on AV96
ARM: dts: stm32: Add alternate pinmux for SDMMC2 pins 4-7
ARM: dts: stm32: Add eMMC attached to SDMMC2 on AV96
ARM: dts: stm32: Repair PMIC configuration on AV96
ARM: dts: stm32: Repair PMIC interrupt on AV96
ARM: dts: stm32: Add QSPI NOR on AV96
ARM: dts: stm32: Add configuration EEPROM on AV96
ARM: dts: stm32: Enable GPU on AV96
ARM: dts: stm32: Add alternate pinmux for SDMMC3 pins
ARM: dts: stm32: Enable WiFi on AV96
ARM: dts: stm32: Add alternate pinmux for USART2 pins
ARM: dts: stm32: Enable Bluetooth on AV96
ARM: dts: stm32: Add alternate pinmux for LTDC pins
ARM: dts: stm32: Add bindings for HDMI video on AV96
ARM: dts: stm32: Add bindings for audio on AV96
ARM: dts: stm32: Add bindings for USB on AV96
ARM: dts: stm32: Rename LEDs to match silkscreen on AV96
arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 248 +++++++++++++++
arch/arm/boot/dts/stm32mp157a-avenger96.dts | 328 ++++++++++++++++++--
2 files changed, 543 insertions(+), 33 deletions(-)
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 46+ messages in thread
* [PATCH V2 01/22] ARM: dts: stm32: Add alternate pinmux for ethernet RGMII
2020-03-31 0:56 [PATCH V2 00/22] ARM: dts: stm32: Repair AV96 board Marek Vasut
@ 2020-03-31 0:56 ` Marek Vasut
2020-03-31 4:13 ` Manivannan Sadhasivam
2020-03-31 0:56 ` [PATCH V2 02/22] ARM: dts: stm32: Repair ethernet operation on AV96 Marek Vasut
` (21 subsequent siblings)
22 siblings, 1 reply; 46+ messages in thread
From: Marek Vasut @ 2020-03-31 0:56 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Marek Vasut, Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, Manivannan Sadhasivam, linux-stm32
Add another mux option for DWMAC RGMII, this is used on AV96 board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
---
V2: No change
---
arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 51 ++++++++++++++++++++++++
1 file changed, 51 insertions(+)
diff --git a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
index 73c07f0dfad2..4569dc16e5a1 100644
--- a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
@@ -196,6 +196,57 @@ pins1 {
};
};
+ ethernet0_rgmii_pins_b: rgmii-1 {
+ pins1 {
+ pinmux = <STM32_PINMUX('G', 5, AF11)>, /* ETH_RGMII_CLK125 */
+ <STM32_PINMUX('G', 4, AF11)>, /* ETH_RGMII_GTX_CLK */
+ <STM32_PINMUX('B', 12, AF11)>, /* ETH_RGMII_TXD0 */
+ <STM32_PINMUX('G', 14, AF11)>, /* ETH_RGMII_TXD1 */
+ <STM32_PINMUX('C', 2, AF11)>, /* ETH_RGMII_TXD2 */
+ <STM32_PINMUX('E', 2, AF11)>, /* ETH_RGMII_TXD3 */
+ <STM32_PINMUX('G', 11, AF11)>, /* ETH_RGMII_TX_CTL */
+ <STM32_PINMUX('C', 1, AF11)>; /* ETH_MDC */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <2>;
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('A', 2, AF11)>; /* ETH_MDIO */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <0>;
+ };
+ pins3 {
+ pinmux = <STM32_PINMUX('C', 4, AF11)>, /* ETH_RGMII_RXD0 */
+ <STM32_PINMUX('C', 5, AF11)>, /* ETH_RGMII_RXD1 */
+ <STM32_PINMUX('H', 6, AF11)>, /* ETH_RGMII_RXD2 */
+ <STM32_PINMUX('B', 1, AF11)>, /* ETH_RGMII_RXD3 */
+ <STM32_PINMUX('A', 1, AF11)>, /* ETH_RGMII_RX_CLK */
+ <STM32_PINMUX('A', 7, AF11)>; /* ETH_RGMII_RX_CTL */
+ bias-disable;
+ };
+ };
+
+ ethernet0_rgmii_pins_sleep_b: rgmii-sleep-1 {
+ pins1 {
+ pinmux = <STM32_PINMUX('G', 5, ANALOG)>, /* ETH_RGMII_CLK125 */
+ <STM32_PINMUX('G', 4, ANALOG)>, /* ETH_RGMII_GTX_CLK */
+ <STM32_PINMUX('B', 12, ANALOG)>, /* ETH_RGMII_TXD0 */
+ <STM32_PINMUX('G', 14, ANALOG)>, /* ETH_RGMII_TXD1 */
+ <STM32_PINMUX('C', 2, ANALOG)>, /* ETH_RGMII_TXD2 */
+ <STM32_PINMUX('E', 2, ANALOG)>, /* ETH_RGMII_TXD3 */
+ <STM32_PINMUX('G', 11, ANALOG)>, /* ETH_RGMII_TX_CTL */
+ <STM32_PINMUX('A', 2, ANALOG)>, /* ETH_MDIO */
+ <STM32_PINMUX('C', 1, ANALOG)>, /* ETH_MDC */
+ <STM32_PINMUX('C', 4, ANALOG)>, /* ETH_RGMII_RXD0 */
+ <STM32_PINMUX('C', 5, ANALOG)>, /* ETH_RGMII_RXD1 */
+ <STM32_PINMUX('H', 6, ANALOG)>, /* ETH_RGMII_RXD2 */
+ <STM32_PINMUX('B', 1, ANALOG)>, /* ETH_RGMII_RXD3 */
+ <STM32_PINMUX('A', 1, ANALOG)>, /* ETH_RGMII_RX_CLK */
+ <STM32_PINMUX('A', 7, ANALOG)>; /* ETH_RGMII_RX_CTL */
+ };
+ };
+
fmc_pins_a: fmc-0 {
pins1 {
pinmux = <STM32_PINMUX('D', 4, AF12)>, /* FMC_NOE */
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH V2 02/22] ARM: dts: stm32: Repair ethernet operation on AV96
2020-03-31 0:56 [PATCH V2 00/22] ARM: dts: stm32: Repair AV96 board Marek Vasut
2020-03-31 0:56 ` [PATCH V2 01/22] ARM: dts: stm32: Add alternate pinmux for ethernet RGMII Marek Vasut
@ 2020-03-31 0:56 ` Marek Vasut
2020-03-31 4:13 ` Manivannan Sadhasivam
2020-03-31 0:56 ` [PATCH V2 03/22] ARM: dts: stm32: Add missing ethernet PHY reset " Marek Vasut
` (20 subsequent siblings)
22 siblings, 1 reply; 46+ messages in thread
From: Marek Vasut @ 2020-03-31 0:56 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Marek Vasut, Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, Manivannan Sadhasivam, linux-stm32
The AV96 RGMII uses different pinmux for ETH_RGMII_TXD0, ETH_RGMII_RXD2
and ETH_RGMII_TX_CTL. Use the correct pinmux to make ethernet operational.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
---
V2: No change
---
arch/arm/boot/dts/stm32mp157a-avenger96.dts | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
index 425175f7d83c..1d15b745feeb 100644
--- a/arch/arm/boot/dts/stm32mp157a-avenger96.dts
+++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
@@ -81,8 +81,8 @@ led6 {
ðernet0 {
status = "okay";
- pinctrl-0 = <ðernet0_rgmii_pins_a>;
- pinctrl-1 = <ðernet0_rgmii_pins_sleep_a>;
+ pinctrl-0 = <ðernet0_rgmii_pins_b>;
+ pinctrl-1 = <ðernet0_rgmii_pins_sleep_b>;
pinctrl-names = "default", "sleep";
phy-mode = "rgmii";
max-speed = <1000>;
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH V2 03/22] ARM: dts: stm32: Add missing ethernet PHY reset on AV96
2020-03-31 0:56 [PATCH V2 00/22] ARM: dts: stm32: Repair AV96 board Marek Vasut
2020-03-31 0:56 ` [PATCH V2 01/22] ARM: dts: stm32: Add alternate pinmux for ethernet RGMII Marek Vasut
2020-03-31 0:56 ` [PATCH V2 02/22] ARM: dts: stm32: Repair ethernet operation on AV96 Marek Vasut
@ 2020-03-31 0:56 ` Marek Vasut
2020-03-31 4:21 ` Manivannan Sadhasivam
2020-03-31 0:56 ` [PATCH V2 04/22] ARM: dts: stm32: Add missing ethernet PHY skews " Marek Vasut
` (19 subsequent siblings)
22 siblings, 1 reply; 46+ messages in thread
From: Marek Vasut @ 2020-03-31 0:56 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Marek Vasut, Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, Manivannan Sadhasivam, linux-stm32
Add PHY reset GPIO on AV96 ethernet PHY.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
---
V2: No change
---
arch/arm/boot/dts/stm32mp157a-avenger96.dts | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
index 1d15b745feeb..a568d3824cb0 100644
--- a/arch/arm/boot/dts/stm32mp157a-avenger96.dts
+++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
@@ -87,6 +87,8 @@ ðernet0 {
phy-mode = "rgmii";
max-speed = <1000>;
phy-handle = <&phy0>;
+ phy-reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <100>;
mdio0 {
#address-cells = <1>;
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH V2 04/22] ARM: dts: stm32: Add missing ethernet PHY skews on AV96
2020-03-31 0:56 [PATCH V2 00/22] ARM: dts: stm32: Repair AV96 board Marek Vasut
` (2 preceding siblings ...)
2020-03-31 0:56 ` [PATCH V2 03/22] ARM: dts: stm32: Add missing ethernet PHY reset " Marek Vasut
@ 2020-03-31 0:56 ` Marek Vasut
2020-03-31 4:22 ` Manivannan Sadhasivam
2020-03-31 0:56 ` [PATCH V2 05/22] ARM: dts: stm32: Add alternate pinmux for SDMMC1 direction pins Marek Vasut
` (18 subsequent siblings)
22 siblings, 1 reply; 46+ messages in thread
From: Marek Vasut @ 2020-03-31 0:56 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Marek Vasut, Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, Manivannan Sadhasivam, linux-stm32
The KS9031 PHY supports configurable PHY skews to compensate for
the board routing. Fill in the correct values.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
---
V2: No change
---
arch/arm/boot/dts/stm32mp157a-avenger96.dts | 14 ++++++++++++++
1 file changed, 14 insertions(+)
diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
index a568d3824cb0..e58653ccb60f 100644
--- a/arch/arm/boot/dts/stm32mp157a-avenger96.dts
+++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
@@ -96,6 +96,20 @@ mdio0 {
compatible = "snps,dwmac-mdio";
phy0: ethernet-phy@7 {
reg = <7>;
+
+ rxc-skew-ps = <1500>;
+ rxdv-skew-ps = <540>;
+ rxd0-skew-ps = <420>;
+ rxd1-skew-ps = <420>;
+ rxd2-skew-ps = <420>;
+ rxd3-skew-ps = <420>;
+
+ txc-skew-ps = <1440>;
+ txen-skew-ps = <540>;
+ txd0-skew-ps = <420>;
+ txd1-skew-ps = <420>;
+ txd2-skew-ps = <420>;
+ txd3-skew-ps = <420>;
};
};
};
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH V2 05/22] ARM: dts: stm32: Add alternate pinmux for SDMMC1 direction pins
2020-03-31 0:56 [PATCH V2 00/22] ARM: dts: stm32: Repair AV96 board Marek Vasut
` (3 preceding siblings ...)
2020-03-31 0:56 ` [PATCH V2 04/22] ARM: dts: stm32: Add missing ethernet PHY skews " Marek Vasut
@ 2020-03-31 0:56 ` Marek Vasut
2020-03-31 4:28 ` Manivannan Sadhasivam
2020-03-31 0:56 ` [PATCH V2 06/22] ARM: dts: stm32: Repair SDMMC1 operation on AV96 Marek Vasut
` (17 subsequent siblings)
22 siblings, 1 reply; 46+ messages in thread
From: Marek Vasut @ 2020-03-31 0:56 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Marek Vasut, Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, Manivannan Sadhasivam, linux-stm32
Add another mux option for SDMMC1 direction pins, in particular
SDMMC1_D123DIR, this is used on AV96 board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
---
V2: Fix SDMMC1_D123DIR AF, should be AF11
---
arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 24 ++++++++++++++++++++++++
1 file changed, 24 insertions(+)
diff --git a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
index 4569dc16e5a1..8ac534c5bdf6 100644
--- a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
@@ -920,6 +920,30 @@ pins {
};
};
+ sdmmc1_dir_pins_b: sdmmc1-dir-1 {
+ pins1 {
+ pinmux = <STM32_PINMUX('F', 2, AF11)>, /* SDMMC1_D0DIR */
+ <STM32_PINMUX('E', 14, AF11)>, /* SDMMC1_D123DIR */
+ <STM32_PINMUX('B', 9, AF11)>; /* SDMMC1_CDIR */
+ slew-rate = <1>;
+ drive-push-pull;
+ bias-pull-up;
+ };
+ pins2{
+ pinmux = <STM32_PINMUX('E', 4, AF8)>; /* SDMMC1_CKIN */
+ bias-pull-up;
+ };
+ };
+
+ sdmmc1_dir_sleep_pins_b: sdmmc1-dir-sleep-1 {
+ pins {
+ pinmux = <STM32_PINMUX('F', 2, ANALOG)>, /* SDMMC1_D0DIR */
+ <STM32_PINMUX('E', 14, ANALOG)>, /* SDMMC1_D123DIR */
+ <STM32_PINMUX('B', 9, ANALOG)>, /* SDMMC1_CDIR */
+ <STM32_PINMUX('E', 4, ANALOG)>; /* SDMMC1_CKIN */
+ };
+ };
+
sdmmc2_b4_pins_a: sdmmc2-b4-0 {
pins1 {
pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH V2 06/22] ARM: dts: stm32: Repair SDMMC1 operation on AV96
2020-03-31 0:56 [PATCH V2 00/22] ARM: dts: stm32: Repair AV96 board Marek Vasut
` (4 preceding siblings ...)
2020-03-31 0:56 ` [PATCH V2 05/22] ARM: dts: stm32: Add alternate pinmux for SDMMC1 direction pins Marek Vasut
@ 2020-03-31 0:56 ` Marek Vasut
2020-03-31 4:33 ` Manivannan Sadhasivam
2020-03-31 0:56 ` [PATCH V2 07/22] ARM: dts: stm32: Add alternate pinmux for SDMMC2 pins 4-7 Marek Vasut
` (16 subsequent siblings)
22 siblings, 1 reply; 46+ messages in thread
From: Marek Vasut @ 2020-03-31 0:56 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Marek Vasut, Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, Manivannan Sadhasivam, linux-stm32
The SD uses different pinmux for the D123DIRline, use such a pinmux,
otherwise there is a pinmux collision on the AV96. Add missing SD
voltage regulator switch.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
---
V2: Disable SDR104, it seems unstable thus far
---
arch/arm/boot/dts/stm32mp157a-avenger96.dts | 21 ++++++++++++++++++---
1 file changed, 18 insertions(+), 3 deletions(-)
diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
index e58653ccb60f..04280353fdbe 100644
--- a/arch/arm/boot/dts/stm32mp157a-avenger96.dts
+++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
@@ -77,6 +77,20 @@ led6 {
default-state = "off";
};
};
+
+ sd_switch: regulator-sd_switch {
+ compatible = "regulator-gpio";
+ regulator-name = "sd_switch";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2900000>;
+ regulator-type = "voltage";
+ regulator-always-on;
+
+ gpios = <&gpioi 5 GPIO_ACTIVE_HIGH>;
+ gpios-states = <0>;
+ states = <1800000 0x1>,
+ <2900000 0x0>;
+ };
};
ðernet0 {
@@ -305,9 +319,9 @@ &rtc {
&sdmmc1 {
pinctrl-names = "default", "opendrain", "sleep";
- pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
- pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
- pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+ pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>;
+ pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_b>;
+ pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_b>;
cd-gpios = <&gpioi 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
disable-wp;
st,sig-dir;
@@ -315,6 +329,7 @@ &sdmmc1 {
st,use-ckin;
bus-width = <4>;
vmmc-supply = <&vdd_sd>;
+ vqmmc-supply = <&sd_switch>;
status = "okay";
};
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH V2 07/22] ARM: dts: stm32: Add alternate pinmux for SDMMC2 pins 4-7
2020-03-31 0:56 [PATCH V2 00/22] ARM: dts: stm32: Repair AV96 board Marek Vasut
` (5 preceding siblings ...)
2020-03-31 0:56 ` [PATCH V2 06/22] ARM: dts: stm32: Repair SDMMC1 operation on AV96 Marek Vasut
@ 2020-03-31 0:56 ` Marek Vasut
2020-03-31 4:36 ` Manivannan Sadhasivam
2020-03-31 0:56 ` [PATCH V2 08/22] ARM: dts: stm32: Add eMMC attached to SDMMC2 on AV96 Marek Vasut
` (15 subsequent siblings)
22 siblings, 1 reply; 46+ messages in thread
From: Marek Vasut @ 2020-03-31 0:56 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Marek Vasut, Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, Manivannan Sadhasivam, linux-stm32
Add another mux option for SDMMC2 pins 4..7, this is used on AV96 board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
---
V2: No change
---
arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 21 +++++++++++++++++++++
1 file changed, 21 insertions(+)
diff --git a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
index 8ac534c5bdf6..ec3621e0ff08 100644
--- a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
@@ -1062,6 +1062,27 @@ pins {
};
};
+ sdmmc2_d47_pins_b: sdmmc2-d47-1 {
+ pins {
+ pinmux = <STM32_PINMUX('A', 8, AF9)>, /* SDMMC2_D4 */
+ <STM32_PINMUX('A', 15, AF9)>, /* SDMMC2_D5 */
+ <STM32_PINMUX('C', 6, AF10)>, /* SDMMC2_D6 */
+ <STM32_PINMUX('C', 7, AF10)>; /* SDMMC2_D7 */
+ slew-rate = <1>;
+ drive-push-pull;
+ bias-pull-up;
+ };
+ };
+
+ sdmmc2_d47_sleep_pins_b: sdmmc2-d47-sleep-1 {
+ pins {
+ pinmux = <STM32_PINMUX('A', 8, ANALOG)>, /* SDMMC2_D4 */
+ <STM32_PINMUX('A', 15, ANALOG)>, /* SDMMC2_D5 */
+ <STM32_PINMUX('C', 6, ANALOG)>, /* SDMMC2_D6 */
+ <STM32_PINMUX('C', 7, ANALOG)>; /* SDMMC2_D7 */
+ };
+ };
+
sdmmc3_b4_pins_a: sdmmc3-b4-0 {
pins1 {
pinmux = <STM32_PINMUX('F', 0, AF9)>, /* SDMMC3_D0 */
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH V2 08/22] ARM: dts: stm32: Add eMMC attached to SDMMC2 on AV96
2020-03-31 0:56 [PATCH V2 00/22] ARM: dts: stm32: Repair AV96 board Marek Vasut
` (6 preceding siblings ...)
2020-03-31 0:56 ` [PATCH V2 07/22] ARM: dts: stm32: Add alternate pinmux for SDMMC2 pins 4-7 Marek Vasut
@ 2020-03-31 0:56 ` Marek Vasut
2020-03-31 4:43 ` Manivannan Sadhasivam
2020-03-31 0:56 ` [PATCH V2 09/22] ARM: dts: stm32: Repair PMIC configuration " Marek Vasut
` (14 subsequent siblings)
22 siblings, 1 reply; 46+ messages in thread
From: Marek Vasut @ 2020-03-31 0:56 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Marek Vasut, Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, Manivannan Sadhasivam, linux-stm32
Add DT node describing the eMMC attached to SDMMC2 controller
of the STM32MP1 on DHCOR SoM, which is the SoM soldered on AV96.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
---
V2: No change
---
arch/arm/boot/dts/stm32mp157a-avenger96.dts | 15 +++++++++++++++
1 file changed, 15 insertions(+)
diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
index 04280353fdbe..6c34a003c3f6 100644
--- a/arch/arm/boot/dts/stm32mp157a-avenger96.dts
+++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
@@ -333,6 +333,21 @@ &sdmmc1 {
status = "okay";
};
+&sdmmc2 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>;
+ pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_b>;
+ pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_b>;
+ bus-width = <8>;
+ mmc-ddr-1_8v;
+ no-sd;
+ no-sdio;
+ non-removable;
+ st,neg-edge;
+ vmmc-supply = <&v1v8>;
+ status = "okay";
+};
+
&uart4 {
/* On Low speed expansion header */
label = "LS-UART1";
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH V2 09/22] ARM: dts: stm32: Repair PMIC configuration on AV96
2020-03-31 0:56 [PATCH V2 00/22] ARM: dts: stm32: Repair AV96 board Marek Vasut
` (7 preceding siblings ...)
2020-03-31 0:56 ` [PATCH V2 08/22] ARM: dts: stm32: Add eMMC attached to SDMMC2 on AV96 Marek Vasut
@ 2020-03-31 0:56 ` Marek Vasut
2020-03-31 0:56 ` [PATCH V2 10/22] ARM: dts: stm32: Repair PMIC interrupt " Marek Vasut
` (13 subsequent siblings)
22 siblings, 0 replies; 46+ messages in thread
From: Marek Vasut @ 2020-03-31 0:56 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Marek Vasut, Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, Manivannan Sadhasivam, linux-stm32
The core and vdd PMIC buck regulators were misconfigured, which caused
instability of the board and malfunction of high-speed interfaces, like
the RGMII. Configure the PMIC correctly to repair these problems.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
---
V2: Model the Enpirion EP53A8LQI on the DHCOR SoM as a fixed regulator
---
arch/arm/boot/dts/stm32mp157a-avenger96.dts | 20 ++++++++++++++++----
1 file changed, 16 insertions(+), 4 deletions(-)
diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
index 6c34a003c3f6..ebe8a134c7ff 100644
--- a/arch/arm/boot/dts/stm32mp157a-avenger96.dts
+++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
@@ -91,6 +91,17 @@ sd_switch: regulator-sd_switch {
states = <1800000 0x1>,
<2900000 0x0>;
};
+
+ /* Enpirion EP3A8LQI U2 on the DHCOR */
+ vdd_io: regulator-buck-io {
+ compatible = "regulator-fixed";
+ regulator-name = "buck-io";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vdd>;
+ };
};
ðernet0 {
@@ -178,7 +189,7 @@ regulators {
vddcore: buck1 {
regulator-name = "vddcore";
- regulator-min-microvolt = <1200000>;
+ regulator-min-microvolt = <800000>;
regulator-max-microvolt = <1350000>;
regulator-always-on;
regulator-initial-mode = <0>;
@@ -196,8 +207,8 @@ vdd_ddr: buck2 {
vdd: buck3 {
regulator-name = "vdd";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <2900000>;
+ regulator-max-microvolt = <2900000>;
regulator-always-on;
regulator-initial-mode = <0>;
regulator-over-current-protection;
@@ -275,6 +286,7 @@ vbus_otg: pwr_sw1 {
regulator-name = "vbus_otg";
interrupts = <IT_OCP_OTG 0>;
interrupt-parent = <&pmic>;
+ regulator-active-discharge = <1>;
};
vbus_sw: pwr_sw2 {
@@ -305,7 +317,7 @@ &iwdg2 {
};
&pwr_regulators {
- vdd-supply = <&vdd>;
+ vdd-supply = <&vdd_io>;
vdd_3v3_usbfs-supply = <&vdd_usb>;
};
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH V2 10/22] ARM: dts: stm32: Repair PMIC interrupt on AV96
2020-03-31 0:56 [PATCH V2 00/22] ARM: dts: stm32: Repair AV96 board Marek Vasut
` (8 preceding siblings ...)
2020-03-31 0:56 ` [PATCH V2 09/22] ARM: dts: stm32: Repair PMIC configuration " Marek Vasut
@ 2020-03-31 0:56 ` Marek Vasut
2020-03-31 0:56 ` [PATCH V2 11/22] ARM: dts: stm32: Add QSPI NOR " Marek Vasut
` (12 subsequent siblings)
22 siblings, 0 replies; 46+ messages in thread
From: Marek Vasut @ 2020-03-31 0:56 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Marek Vasut, Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, Manivannan Sadhasivam, linux-stm32
The PMIC interrupt line is connected to PA0 on the DHCOR SoM, fix it.
This makes the POWER button on the AV96 working, and also all the other
PMIC interrupts. Furthermore, scrub the bogus interrupt-parent props.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
---
V2: No change
---
arch/arm/boot/dts/stm32mp157a-avenger96.dts | 10 +---------
1 file changed, 1 insertion(+), 9 deletions(-)
diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
index ebe8a134c7ff..9a44c8777f67 100644
--- a/arch/arm/boot/dts/stm32mp157a-avenger96.dts
+++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
@@ -171,7 +171,7 @@ &i2c4 {
pmic: stpmic@33 {
compatible = "st,stpmic1";
reg = <0x33>;
- interrupts-extended = <&exti 55 IRQ_TYPE_EDGE_FALLING>;
+ interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
interrupt-controller;
#interrupt-cells = <2>;
status = "okay";
@@ -228,7 +228,6 @@ vdda: ldo1 {
regulator-min-microvolt = <2900000>;
regulator-max-microvolt = <2900000>;
interrupts = <IT_CURLIM_LDO1 0>;
- interrupt-parent = <&pmic>;
};
v2v8: ldo2 {
@@ -236,7 +235,6 @@ v2v8: ldo2 {
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
interrupts = <IT_CURLIM_LDO2 0>;
- interrupt-parent = <&pmic>;
};
vtt_ddr: ldo3 {
@@ -250,7 +248,6 @@ vtt_ddr: ldo3 {
vdd_usb: ldo4 {
regulator-name = "vdd_usb";
interrupts = <IT_CURLIM_LDO4 0>;
- interrupt-parent = <&pmic>;
};
vdd_sd: ldo5 {
@@ -258,7 +255,6 @@ vdd_sd: ldo5 {
regulator-min-microvolt = <2900000>;
regulator-max-microvolt = <2900000>;
interrupts = <IT_CURLIM_LDO5 0>;
- interrupt-parent = <&pmic>;
regulator-boot-on;
};
@@ -267,7 +263,6 @@ v1v8: ldo6 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
interrupts = <IT_CURLIM_LDO6 0>;
- interrupt-parent = <&pmic>;
regulator-enable-ramp-delay = <300000>;
};
@@ -279,20 +274,17 @@ vref_ddr: vref_ddr {
bst_out: boost {
regulator-name = "bst_out";
interrupts = <IT_OCP_BOOST 0>;
- interrupt-parent = <&pmic>;
};
vbus_otg: pwr_sw1 {
regulator-name = "vbus_otg";
interrupts = <IT_OCP_OTG 0>;
- interrupt-parent = <&pmic>;
regulator-active-discharge = <1>;
};
vbus_sw: pwr_sw2 {
regulator-name = "vbus_sw";
interrupts = <IT_OCP_SWOUT 0>;
- interrupt-parent = <&pmic>;
regulator-active-discharge = <1>;
};
};
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH V2 11/22] ARM: dts: stm32: Add QSPI NOR on AV96
2020-03-31 0:56 [PATCH V2 00/22] ARM: dts: stm32: Repair AV96 board Marek Vasut
` (9 preceding siblings ...)
2020-03-31 0:56 ` [PATCH V2 10/22] ARM: dts: stm32: Repair PMIC interrupt " Marek Vasut
@ 2020-03-31 0:56 ` Marek Vasut
2020-03-31 0:56 ` [PATCH V2 12/22] ARM: dts: stm32: Add configuration EEPROM " Marek Vasut
` (11 subsequent siblings)
22 siblings, 0 replies; 46+ messages in thread
From: Marek Vasut @ 2020-03-31 0:56 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Marek Vasut, Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, Manivannan Sadhasivam, linux-stm32
The DH Electronics DHCOR SOM has QSPI NOR on the SoM itself, add it
into the DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
---
V2: Use spi-flash in the DT node instead of explicit model name
---
arch/arm/boot/dts/stm32mp157a-avenger96.dts | 20 ++++++++++++++++++++
1 file changed, 20 insertions(+)
diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
index 9a44c8777f67..de347453db6c 100644
--- a/arch/arm/boot/dts/stm32mp157a-avenger96.dts
+++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
@@ -21,6 +21,7 @@ aliases {
mmc0 = &sdmmc1;
serial0 = &uart4;
serial1 = &uart7;
+ spi0 = &qspi;
};
chosen {
@@ -313,6 +314,25 @@ &pwr_regulators {
vdd_3v3_usbfs-supply = <&vdd_usb>;
};
+&qspi {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>;
+ pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>;
+ reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ flash0: spi-flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-rx-bus-width = <4>;
+ spi-max-frequency = <108000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+};
+
&rng1 {
status = "okay";
};
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH V2 12/22] ARM: dts: stm32: Add configuration EEPROM on AV96
2020-03-31 0:56 [PATCH V2 00/22] ARM: dts: stm32: Repair AV96 board Marek Vasut
` (10 preceding siblings ...)
2020-03-31 0:56 ` [PATCH V2 11/22] ARM: dts: stm32: Add QSPI NOR " Marek Vasut
@ 2020-03-31 0:56 ` Marek Vasut
2020-03-31 6:34 ` Manivannan Sadhasivam
2020-03-31 0:56 ` [PATCH V2 13/22] ARM: dts: stm32: Enable GPU " Marek Vasut
` (10 subsequent siblings)
22 siblings, 1 reply; 46+ messages in thread
From: Marek Vasut @ 2020-03-31 0:56 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Marek Vasut, Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, Manivannan Sadhasivam, linux-stm32
The board has an EEPROM on the same I2C bus as PMIC, at address 0x53.
The EEPROM contains the board MAC address.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
---
V2: No change
---
arch/arm/boot/dts/stm32mp157a-avenger96.dts | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
index de347453db6c..3dfc51f65709 100644
--- a/arch/arm/boot/dts/stm32mp157a-avenger96.dts
+++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
@@ -302,6 +302,12 @@ watchdog {
status = "disabled";
};
};
+
+ eeprom@53 {
+ compatible = "atmel,24c02";
+ reg = <0x53>;
+ pagesize = <16>;
+ };
};
&iwdg2 {
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH V2 13/22] ARM: dts: stm32: Enable GPU on AV96
2020-03-31 0:56 [PATCH V2 00/22] ARM: dts: stm32: Repair AV96 board Marek Vasut
` (11 preceding siblings ...)
2020-03-31 0:56 ` [PATCH V2 12/22] ARM: dts: stm32: Add configuration EEPROM " Marek Vasut
@ 2020-03-31 0:56 ` Marek Vasut
2020-03-31 6:36 ` Manivannan Sadhasivam
2020-03-31 0:56 ` [PATCH V2 14/22] ARM: dts: stm32: Add alternate pinmux for SDMMC3 pins Marek Vasut
` (9 subsequent siblings)
22 siblings, 1 reply; 46+ messages in thread
From: Marek Vasut @ 2020-03-31 0:56 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Marek Vasut, Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, Manivannan Sadhasivam, linux-stm32
Enable the GPU present on the STM32MP1 populated on AV96.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
---
V2: No change
---
arch/arm/boot/dts/stm32mp157a-avenger96.dts | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
index 3dfc51f65709..3aeb3afa37d9 100644
--- a/arch/arm/boot/dts/stm32mp157a-avenger96.dts
+++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
@@ -140,6 +140,10 @@ phy0: ethernet-phy@7 {
};
};
+&gpu {
+ status = "okay";
+};
+
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins_b>;
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH V2 14/22] ARM: dts: stm32: Add alternate pinmux for SDMMC3 pins
2020-03-31 0:56 [PATCH V2 00/22] ARM: dts: stm32: Repair AV96 board Marek Vasut
` (12 preceding siblings ...)
2020-03-31 0:56 ` [PATCH V2 13/22] ARM: dts: stm32: Enable GPU " Marek Vasut
@ 2020-03-31 0:56 ` Marek Vasut
2020-03-31 6:40 ` Manivannan Sadhasivam
2020-03-31 0:56 ` [PATCH V2 15/22] ARM: dts: stm32: Enable WiFi on AV96 Marek Vasut
` (8 subsequent siblings)
22 siblings, 1 reply; 46+ messages in thread
From: Marek Vasut @ 2020-03-31 0:56 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Marek Vasut, Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, Manivannan Sadhasivam, linux-stm32
Add another mux option for SDMMC3 pins, in particular PD5_SDMMC3_D2 and
PD0_SDMMC3_CMD, this is used on AV96 board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
---
V2: No change
---
arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 54 ++++++++++++++++++++++++
1 file changed, 54 insertions(+)
diff --git a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
index ec3621e0ff08..f3f9fc4a3503 100644
--- a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
@@ -1137,6 +1137,60 @@ pins {
};
};
+ sdmmc3_b4_pins_b: sdmmc3-b4-1 {
+ pins1 {
+ pinmux = <STM32_PINMUX('F', 0, AF9)>, /* SDMMC3_D0 */
+ <STM32_PINMUX('F', 4, AF9)>, /* SDMMC3_D1 */
+ <STM32_PINMUX('D', 5, AF10)>, /* SDMMC3_D2 */
+ <STM32_PINMUX('D', 7, AF10)>, /* SDMMC3_D3 */
+ <STM32_PINMUX('D', 0, AF10)>; /* SDMMC3_CMD */
+ slew-rate = <1>;
+ drive-push-pull;
+ bias-pull-up;
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('G', 15, AF10)>; /* SDMMC3_CK */
+ slew-rate = <2>;
+ drive-push-pull;
+ bias-pull-up;
+ };
+ };
+
+ sdmmc3_b4_od_pins_b: sdmmc3-b4-od-1 {
+ pins1 {
+ pinmux = <STM32_PINMUX('F', 0, AF9)>, /* SDMMC3_D0 */
+ <STM32_PINMUX('F', 4, AF9)>, /* SDMMC3_D1 */
+ <STM32_PINMUX('D', 5, AF10)>, /* SDMMC3_D2 */
+ <STM32_PINMUX('D', 7, AF10)>; /* SDMMC3_D3 */
+ slew-rate = <1>;
+ drive-push-pull;
+ bias-pull-up;
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('G', 15, AF10)>; /* SDMMC3_CK */
+ slew-rate = <2>;
+ drive-push-pull;
+ bias-pull-up;
+ };
+ pins3 {
+ pinmux = <STM32_PINMUX('D', 0, AF10)>; /* SDMMC2_CMD */
+ slew-rate = <1>;
+ drive-open-drain;
+ bias-pull-up;
+ };
+ };
+
+ sdmmc3_b4_sleep_pins_b: sdmmc3-b4-sleep-1 {
+ pins {
+ pinmux = <STM32_PINMUX('F', 0, ANALOG)>, /* SDMMC3_D0 */
+ <STM32_PINMUX('F', 4, ANALOG)>, /* SDMMC3_D1 */
+ <STM32_PINMUX('D', 5, ANALOG)>, /* SDMMC3_D2 */
+ <STM32_PINMUX('D', 7, ANALOG)>, /* SDMMC3_D3 */
+ <STM32_PINMUX('G', 15, ANALOG)>, /* SDMMC3_CK */
+ <STM32_PINMUX('D', 0, ANALOG)>; /* SDMMC3_CMD */
+ };
+ };
+
spdifrx_pins_a: spdifrx-0 {
pins {
pinmux = <STM32_PINMUX('G', 12, AF8)>; /* SPDIF_IN1 */
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH V2 15/22] ARM: dts: stm32: Enable WiFi on AV96
2020-03-31 0:56 [PATCH V2 00/22] ARM: dts: stm32: Repair AV96 board Marek Vasut
` (13 preceding siblings ...)
2020-03-31 0:56 ` [PATCH V2 14/22] ARM: dts: stm32: Add alternate pinmux for SDMMC3 pins Marek Vasut
@ 2020-03-31 0:56 ` Marek Vasut
2020-03-31 6:43 ` Manivannan Sadhasivam
2020-03-31 0:56 ` [PATCH V2 16/22] ARM: dts: stm32: Add alternate pinmux for USART2 pins Marek Vasut
` (7 subsequent siblings)
22 siblings, 1 reply; 46+ messages in thread
From: Marek Vasut @ 2020-03-31 0:56 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Marek Vasut, Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, Manivannan Sadhasivam, linux-stm32
The WiFi/Bluetooth SDIO chip is attached to SDMMC3 on AV96, describe it
in DT to make it available. Remove WiFi LED and turn it into a regulator,
because it is a GPIO controlling the WL_REG_ON input of the WiFi chip.
The LED is just an indicator connected to the same line, but not the
primary function.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
---
V2: No change
---
arch/arm/boot/dts/stm32mp157a-avenger96.dts | 38 +++++++++++++++++----
1 file changed, 31 insertions(+), 7 deletions(-)
diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
index 3aeb3afa37d9..12ee95d5adb1 100644
--- a/arch/arm/boot/dts/stm32mp157a-avenger96.dts
+++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
@@ -65,13 +65,6 @@ led4 {
};
led5 {
- label = "yellow:wifi";
- gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "phy0tx";
- default-state = "off";
- };
-
- led6 {
label = "blue:bt";
gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "bluetooth-power";
@@ -103,6 +96,17 @@ vdd_io: regulator-buck-io {
regulator-boot-on;
vin-supply = <&vdd>;
};
+
+ wlan_pwr: regulator-wlan {
+ compatible = "regulator-fixed";
+
+ regulator-name = "wl-reg";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
};
ðernet0 {
@@ -382,6 +386,26 @@ &sdmmc2 {
status = "okay";
};
+&sdmmc3 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc3_b4_pins_b>;
+ pinctrl-1 = <&sdmmc3_b4_od_pins_b>;
+ pinctrl-2 = <&sdmmc3_b4_sleep_pins_b>;
+ broken-cd;
+ non-removable;
+ st,neg-edge;
+ bus-width = <4>;
+ vmmc-supply = <&wlan_pwr>;
+ status = "okay";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ brcmf: bcrmf@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
+};
+
&uart4 {
/* On Low speed expansion header */
label = "LS-UART1";
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH V2 16/22] ARM: dts: stm32: Add alternate pinmux for USART2 pins
2020-03-31 0:56 [PATCH V2 00/22] ARM: dts: stm32: Repair AV96 board Marek Vasut
` (14 preceding siblings ...)
2020-03-31 0:56 ` [PATCH V2 15/22] ARM: dts: stm32: Enable WiFi on AV96 Marek Vasut
@ 2020-03-31 0:56 ` Marek Vasut
2020-03-31 6:46 ` Manivannan Sadhasivam
2020-03-31 0:56 ` [PATCH V2 17/22] ARM: dts: stm32: Enable Bluetooth on AV96 Marek Vasut
` (6 subsequent siblings)
22 siblings, 1 reply; 46+ messages in thread
From: Marek Vasut @ 2020-03-31 0:56 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Marek Vasut, Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, Manivannan Sadhasivam, linux-stm32
Add mux option for USART2 pins, this is used on AV96 board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
---
V2: No change
---
arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 24 ++++++++++++++++++++++++
1 file changed, 24 insertions(+)
diff --git a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
index f3f9fc4a3503..4f3b40d5751f 100644
--- a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
@@ -1204,6 +1204,30 @@ pins {
};
};
+ usart2_pins_a: usart2-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('F', 5, AF7)>, /* USART2_TX */
+ <STM32_PINMUX('D', 4, AF7)>; /* USART2_RTS */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <0>;
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('D', 6, AF7)>, /* USART2_RX */
+ <STM32_PINMUX('D', 3, AF7)>; /* USART2_CTS_NSS */
+ bias-disable;
+ };
+ };
+
+ usart2_sleep_pins_a: usart2-sleep-0 {
+ pins {
+ pinmux = <STM32_PINMUX('F', 5, ANALOG)>, /* USART2_TX */
+ <STM32_PINMUX('D', 4, ANALOG)>, /* USART2_RTS */
+ <STM32_PINMUX('D', 6, ANALOG)>, /* USART2_RX */
+ <STM32_PINMUX('D', 3, ANALOG)>; /* USART2_CTS_NSS */
+ };
+ };
+
usart3_pins_a: usart3-0 {
pins1 {
pinmux = <STM32_PINMUX('B', 10, AF7)>; /* USART3_TX */
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH V2 17/22] ARM: dts: stm32: Enable Bluetooth on AV96
2020-03-31 0:56 [PATCH V2 00/22] ARM: dts: stm32: Repair AV96 board Marek Vasut
` (15 preceding siblings ...)
2020-03-31 0:56 ` [PATCH V2 16/22] ARM: dts: stm32: Add alternate pinmux for USART2 pins Marek Vasut
@ 2020-03-31 0:56 ` Marek Vasut
2020-03-31 6:47 ` Manivannan Sadhasivam
2020-03-31 0:56 ` [PATCH V2 18/22] ARM: dts: stm32: Add alternate pinmux for LTDC pins Marek Vasut
` (5 subsequent siblings)
22 siblings, 1 reply; 46+ messages in thread
From: Marek Vasut @ 2020-03-31 0:56 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Marek Vasut, Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, Manivannan Sadhasivam, linux-stm32
The WiFi/Bluetooth chip is attached to USART2 on AV96 as well, describe
it in DT to make it available. Remove BT LED and turn it into a shutdown
GPIO, because the GPIO line controls the BT_REG_ON signal. The LED is just
an indicator connected to the same line, but not the primary function.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
---
V2: No change
---
arch/arm/boot/dts/stm32mp157a-avenger96.dts | 23 ++++++++++++++-------
1 file changed, 16 insertions(+), 7 deletions(-)
diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
index 12ee95d5adb1..29af5ed2ebb3 100644
--- a/arch/arm/boot/dts/stm32mp157a-avenger96.dts
+++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
@@ -21,6 +21,7 @@ aliases {
mmc0 = &sdmmc1;
serial0 = &uart4;
serial1 = &uart7;
+ serial2 = &usart2;
spi0 = &qspi;
};
@@ -63,13 +64,6 @@ led4 {
default-state = "off";
panic-indicator;
};
-
- led5 {
- label = "blue:bt";
- gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "bluetooth-power";
- default-state = "off";
- };
};
sd_switch: regulator-sd_switch {
@@ -421,3 +415,18 @@ &uart7 {
pinctrl-0 = <&uart7_pins_a>;
status = "okay";
};
+
+/* Bluetooth */
+&usart2 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&usart2_pins_a>;
+ pinctrl-1 = <&usart2_sleep_pins_a>;
+ st,hw-flow-ctrl;
+ status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ max-speed = <3000000>;
+ shutdown-gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>;
+ };
+};
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH V2 18/22] ARM: dts: stm32: Add alternate pinmux for LTDC pins
2020-03-31 0:56 [PATCH V2 00/22] ARM: dts: stm32: Repair AV96 board Marek Vasut
` (16 preceding siblings ...)
2020-03-31 0:56 ` [PATCH V2 17/22] ARM: dts: stm32: Enable Bluetooth on AV96 Marek Vasut
@ 2020-03-31 0:56 ` Marek Vasut
2020-03-31 0:56 ` [PATCH V2 19/22] ARM: dts: stm32: Add bindings for HDMI video on AV96 Marek Vasut
` (4 subsequent siblings)
22 siblings, 0 replies; 46+ messages in thread
From: Marek Vasut @ 2020-03-31 0:56 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Marek Vasut, Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, Manivannan Sadhasivam, linux-stm32
Add new mux option for LTDC pins, this is used on AV96 board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
---
V2: No change
---
arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 74 ++++++++++++++++++++++++
1 file changed, 74 insertions(+)
diff --git a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
index 4f3b40d5751f..d820b3d3ab57 100644
--- a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
@@ -532,6 +532,80 @@ pins {
};
};
+ ltdc_pins_c: ltdc-c-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('G', 7, AF14)>; /* LCD_CLK */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <3>;
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('I', 10, AF14)>, /* LCD_HSYNC */
+ <STM32_PINMUX('I', 9, AF14)>, /* LCD_VSYNC */
+ <STM32_PINMUX('E', 13, AF14)>, /* LCD_DE */
+ <STM32_PINMUX('G', 13, AF14)>, /* LCD_R0 */
+ <STM32_PINMUX('H', 3, AF14)>, /* LCD_R1 */
+ <STM32_PINMUX('H', 8, AF14)>, /* LCD_R2 */
+ <STM32_PINMUX('H', 9, AF14)>, /* LCD_R3 */
+ <STM32_PINMUX('A', 5, AF14)>, /* LCD_R4 */
+ <STM32_PINMUX('H', 11, AF14)>, /* LCD_R5 */
+ <STM32_PINMUX('H', 12, AF14)>, /* LCD_R6 */
+ <STM32_PINMUX('E', 15, AF14)>, /* LCD_R7 */
+ <STM32_PINMUX('E', 5, AF14)>, /* LCD_G0 */
+ <STM32_PINMUX('B', 0, AF14)>, /* LCD_G1 */
+ <STM32_PINMUX('H', 13, AF14)>, /* LCD_G2 */
+ <STM32_PINMUX('E', 11, AF14)>, /* LCD_G3 */
+ <STM32_PINMUX('H', 15, AF14)>, /* LCD_G4 */
+ <STM32_PINMUX('H', 4, AF9)>, /* LCD_G5 */
+ <STM32_PINMUX('I', 11, AF9)>, /* LCD_G6 */
+ <STM32_PINMUX('G', 8, AF14)>, /* LCD_G7 */
+ <STM32_PINMUX('D', 9, AF14)>, /* LCD_B0 */
+ <STM32_PINMUX('G', 12, AF14)>, /* LCD_B1 */
+ <STM32_PINMUX('G', 10, AF14)>, /* LCD_B2 */
+ <STM32_PINMUX('D', 10, AF14)>, /* LCD_B3 */
+ <STM32_PINMUX('E', 12, AF14)>, /* LCD_B4 */
+ <STM32_PINMUX('A', 3, AF14)>, /* LCD_B5 */
+ <STM32_PINMUX('B', 8, AF14)>, /* LCD_B6 */
+ <STM32_PINMUX('I', 7, AF14)>; /* LCD_B7 */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <2>;
+ };
+ };
+
+ ltdc_pins_sleep_c: ltdc-c-1 {
+ pins {
+ pinmux = <STM32_PINMUX('G', 7, ANALOG)>, /* LCD_CLK */
+ <STM32_PINMUX('I', 10, ANALOG)>, /* LCD_HSYNC */
+ <STM32_PINMUX('I', 9, ANALOG)>, /* LCD_VSYNC */
+ <STM32_PINMUX('E', 13, ANALOG)>, /* LCD_DE */
+ <STM32_PINMUX('G', 13, ANALOG)>, /* LCD_R0 */
+ <STM32_PINMUX('H', 3, ANALOG)>, /* LCD_R1 */
+ <STM32_PINMUX('H', 8, ANALOG)>, /* LCD_R2 */
+ <STM32_PINMUX('H', 9, ANALOG)>, /* LCD_R3 */
+ <STM32_PINMUX('A', 5, ANALOG)>, /* LCD_R4 */
+ <STM32_PINMUX('H', 11, ANALOG)>, /* LCD_R5 */
+ <STM32_PINMUX('H', 12, ANALOG)>, /* LCD_R6 */
+ <STM32_PINMUX('E', 15, ANALOG)>, /* LCD_R7 */
+ <STM32_PINMUX('E', 5, ANALOG)>, /* LCD_G0 */
+ <STM32_PINMUX('B', 0, ANALOG)>, /* LCD_G1 */
+ <STM32_PINMUX('H', 13, ANALOG)>, /* LCD_G2 */
+ <STM32_PINMUX('E', 11, ANALOG)>, /* LCD_G3 */
+ <STM32_PINMUX('H', 15, ANALOG)>, /* LCD_G4 */
+ <STM32_PINMUX('H', 4, ANALOG)>, /* LCD_G5 */
+ <STM32_PINMUX('I', 11, ANALOG)>, /* LCD_G6 */
+ <STM32_PINMUX('G', 8, ANALOG)>, /* LCD_G7 */
+ <STM32_PINMUX('D', 9, ANALOG)>, /* LCD_B0 */
+ <STM32_PINMUX('G', 12, ANALOG)>, /* LCD_B1 */
+ <STM32_PINMUX('G', 10, ANALOG)>, /* LCD_B2 */
+ <STM32_PINMUX('D', 10, ANALOG)>, /* LCD_B3 */
+ <STM32_PINMUX('E', 12, ANALOG)>, /* LCD_B4 */
+ <STM32_PINMUX('A', 3, ANALOG)>, /* LCD_B5 */
+ <STM32_PINMUX('B', 8, ANALOG)>, /* LCD_B6 */
+ <STM32_PINMUX('I', 7, ANALOG)>; /* LCD_B7 */
+ };
+ };
+
m_can1_pins_a: m-can1-0 {
pins1 {
pinmux = <STM32_PINMUX('H', 13, AF9)>; /* CAN1_TX */
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH V2 19/22] ARM: dts: stm32: Add bindings for HDMI video on AV96
2020-03-31 0:56 [PATCH V2 00/22] ARM: dts: stm32: Repair AV96 board Marek Vasut
` (17 preceding siblings ...)
2020-03-31 0:56 ` [PATCH V2 18/22] ARM: dts: stm32: Add alternate pinmux for LTDC pins Marek Vasut
@ 2020-03-31 0:56 ` Marek Vasut
2020-03-31 0:56 ` [PATCH V2 20/22] ARM: dts: stm32: Add bindings for audio " Marek Vasut
` (3 subsequent siblings)
22 siblings, 0 replies; 46+ messages in thread
From: Marek Vasut @ 2020-03-31 0:56 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Marek Vasut, Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, Manivannan Sadhasivam, linux-stm32
Fill in the HDMI video pipeline from AV96 into the DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
---
V2: No change
---
arch/arm/boot/dts/stm32mp157a-avenger96.dts | 79 +++++++++++++++++++++
1 file changed, 79 insertions(+)
diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
index 29af5ed2ebb3..e511fdcb8c46 100644
--- a/arch/arm/boot/dts/stm32mp157a-avenger96.dts
+++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
@@ -25,10 +25,28 @@ aliases {
spi0 = &qspi;
};
+ /* XTal Q1 */
+ cec_clock: clk-cec-fixed {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ };
+
chosen {
stdout-path = "serial0:115200n8";
};
+ hdmi-out {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con: endpoint {
+ remote-endpoint = <&adv7513_out>;
+ };
+ };
+ };
+
memory@c0000000 {
device_type = "memory";
reg = <0xc0000000 0x40000000>;
@@ -305,6 +323,50 @@ watchdog {
};
};
+ hdmi-transmitter@3d {
+ compatible = "adi,adv7513";
+ reg = <0x3d>, <0x2d>, <0x4d>, <0x5d>;
+ reg-names = "main", "cec", "edid", "packet";
+ clocks = <&cec_clock>;
+ clock-names = "cec";
+
+ avdd-supply = <&v3v3>;
+ dvdd-supply = <&v3v3>;
+ pvdd-supply = <&v3v3>;
+ dvdd-3v-supply = <&v3v3>;
+ bgvdd-supply = <&v3v3>;
+
+ interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-parent = <&gpiog>;
+
+ status = "okay";
+
+ adi,input-depth = <8>;
+ adi,input-colorspace = "rgb";
+ adi,input-clock = "1x";
+ adi,input-style = <1>;
+ adi,input-justification = "evenly";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ adv7513_in: endpoint {
+ remote-endpoint = <<dc_ep0_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ adv7513_out: endpoint {
+ remote-endpoint = <&hdmi_con>;
+ };
+ };
+ };
+ };
+
eeprom@53 {
compatible = "atmel,24c02";
reg = <0x53>;
@@ -317,6 +379,23 @@ &iwdg2 {
status = "okay";
};
+<dc {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <<dc_pins_c>;
+ pinctrl-1 = <<dc_pins_sleep_c>;
+ status = "okay";
+
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ltdc_ep0_out: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&adv7513_in>;
+ };
+ };
+};
+
&pwr_regulators {
vdd-supply = <&vdd_io>;
vdd_3v3_usbfs-supply = <&vdd_usb>;
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH V2 20/22] ARM: dts: stm32: Add bindings for audio on AV96
2020-03-31 0:56 [PATCH V2 00/22] ARM: dts: stm32: Repair AV96 board Marek Vasut
` (18 preceding siblings ...)
2020-03-31 0:56 ` [PATCH V2 19/22] ARM: dts: stm32: Add bindings for HDMI video on AV96 Marek Vasut
@ 2020-03-31 0:56 ` Marek Vasut
2020-03-31 0:57 ` [PATCH V2 21/22] ARM: dts: stm32: Add bindings for USB " Marek Vasut
` (2 subsequent siblings)
22 siblings, 0 replies; 46+ messages in thread
From: Marek Vasut @ 2020-03-31 0:56 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Marek Vasut, Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, Manivannan Sadhasivam, linux-stm32
Fill in the bindings for HDMI audio on AV96, this permits audio playback
via attached HDMI device if such device supports it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
---
V2: No change
---
arch/arm/boot/dts/stm32mp157a-avenger96.dts | 39 +++++++++++++++++++++
1 file changed, 39 insertions(+)
diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
index e511fdcb8c46..110ee1ea5daf 100644
--- a/arch/arm/boot/dts/stm32mp157a-avenger96.dts
+++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
@@ -98,6 +98,13 @@ sd_switch: regulator-sd_switch {
<2900000 0x0>;
};
+ sound {
+ compatible = "audio-graph-card";
+ label = "STM32MP1-AV96-HDMI";
+ dais = <&sai2a_port>;
+ status = "okay";
+ };
+
/* Enpirion EP3A8LQI U2 on the DHCOR */
vdd_io: regulator-buck-io {
compatible = "regulator-fixed";
@@ -364,6 +371,13 @@ adv7513_out: endpoint {
remote-endpoint = <&hdmi_con>;
};
};
+
+ port@2 {
+ reg = <2>;
+ adv7513_i2s0: endpoint {
+ remote-endpoint = <&sai2a_endpoint>;
+ };
+ };
};
};
@@ -428,6 +442,31 @@ &rtc {
status = "okay";
};
+&sai2 {
+ clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sai2a_pins_c>;
+ pinctrl-1 = <&sai2a_sleep_pins_c>;
+ clock-names = "pclk", "x8k", "x11k";
+ status = "okay";
+
+ sai2a: audio-controller@4400b004 {
+ #clock-cells = <0>;
+ dma-names = "tx";
+ clocks = <&rcc SAI2_K>;
+ clock-names = "sai_ck";
+ status = "okay";
+
+ sai2a_port: port {
+ sai2a_endpoint: endpoint {
+ remote-endpoint = <&adv7513_i2s0>;
+ format = "i2s";
+ mclk-fs = <256>;
+ };
+ };
+ };
+};
+
&sdmmc1 {
pinctrl-names = "default", "opendrain", "sleep";
pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>;
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH V2 21/22] ARM: dts: stm32: Add bindings for USB on AV96
2020-03-31 0:56 [PATCH V2 00/22] ARM: dts: stm32: Repair AV96 board Marek Vasut
` (19 preceding siblings ...)
2020-03-31 0:56 ` [PATCH V2 20/22] ARM: dts: stm32: Add bindings for audio " Marek Vasut
@ 2020-03-31 0:57 ` Marek Vasut
2020-03-31 0:57 ` [PATCH V2 22/22] ARM: dts: stm32: Rename LEDs to match silkscreen " Marek Vasut
2020-03-31 4:07 ` [PATCH V2 00/22] ARM: dts: stm32: Repair AV96 board Manivannan Sadhasivam
22 siblings, 0 replies; 46+ messages in thread
From: Marek Vasut @ 2020-03-31 0:57 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Marek Vasut, Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, Manivannan Sadhasivam, linux-stm32
Fill in the bindings for USB host and gadget on AV96.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
---
V2: No change
---
arch/arm/boot/dts/stm32mp157a-avenger96.dts | 31 +++++++++++++++++++++
1 file changed, 31 insertions(+)
diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
index 110ee1ea5daf..b6cb3b2d8c78 100644
--- a/arch/arm/boot/dts/stm32mp157a-avenger96.dts
+++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
@@ -548,3 +548,34 @@ bluetooth {
shutdown-gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>;
};
};
+
+&usbh_ehci {
+ phys = <&usbphyc_port0>;
+ phy-names = "usb";
+ status = "okay";
+};
+
+&usbotg_hs {
+ pinctrl-0 = <&usbotg_hs_pins_a>;
+ pinctrl-names = "default";
+ phy-names = "usb2-phy";
+ phys = <&usbphyc_port1 0>;
+ status = "okay";
+ vbus-supply = <&vbus_otg>;
+};
+
+&usbphyc {
+ status = "okay";
+};
+
+&usbphyc_port0 {
+ phy-supply = <&vdd_usb>;
+ vdda1v1-supply = <®11>;
+ vdda1v8-supply = <®18>;
+};
+
+&usbphyc_port1 {
+ phy-supply = <&vdd_usb>;
+ vdda1v1-supply = <®11>;
+ vdda1v8-supply = <®18>;
+};
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 46+ messages in thread
* [PATCH V2 22/22] ARM: dts: stm32: Rename LEDs to match silkscreen on AV96
2020-03-31 0:56 [PATCH V2 00/22] ARM: dts: stm32: Repair AV96 board Marek Vasut
` (20 preceding siblings ...)
2020-03-31 0:57 ` [PATCH V2 21/22] ARM: dts: stm32: Add bindings for USB " Marek Vasut
@ 2020-03-31 0:57 ` Marek Vasut
2020-03-31 4:09 ` Manivannan Sadhasivam
2020-03-31 4:07 ` [PATCH V2 00/22] ARM: dts: stm32: Repair AV96 board Manivannan Sadhasivam
22 siblings, 1 reply; 46+ messages in thread
From: Marek Vasut @ 2020-03-31 0:57 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Marek Vasut, Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, Manivannan Sadhasivam, linux-stm32
The LED labels do not match the silkscreen on the board, fix it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
---
V2: No change
---
arch/arm/boot/dts/stm32mp157a-avenger96.dts | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
index b6cb3b2d8c78..4291a97cc05f 100644
--- a/arch/arm/boot/dts/stm32mp157a-avenger96.dts
+++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
@@ -55,21 +55,21 @@ memory@c0000000 {
led {
compatible = "gpio-leds";
led1 {
- label = "green:user1";
+ label = "green:user0";
gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
default-state = "off";
};
led2 {
- label = "green:user2";
+ label = "green:user1";
gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "mmc0";
default-state = "off";
};
led3 {
- label = "green:user3";
+ label = "green:user2";
gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "mmc1";
default-state = "off";
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 46+ messages in thread
* Re: [PATCH V2 00/22] ARM: dts: stm32: Repair AV96 board
2020-03-31 0:56 [PATCH V2 00/22] ARM: dts: stm32: Repair AV96 board Marek Vasut
` (21 preceding siblings ...)
2020-03-31 0:57 ` [PATCH V2 22/22] ARM: dts: stm32: Rename LEDs to match silkscreen " Marek Vasut
@ 2020-03-31 4:07 ` Manivannan Sadhasivam
2020-03-31 13:44 ` Marek Vasut
22 siblings, 1 reply; 46+ messages in thread
From: Manivannan Sadhasivam @ 2020-03-31 4:07 UTC (permalink / raw)
To: Marek Vasut
Cc: Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, linux-stm32, linux-arm-kernel
Hi Marek,
Thanks for the series.
On Tue, Mar 31, 2020 at 02:56:39AM +0200, Marek Vasut wrote:
> The AV96 board device tree is completely broken and does not match the
> hardware. This series fixes it up.
>
Completely broken? The patch submitted previously was an initial one and there
were many interfaces not enabled. I agree that there are few _obvious_ things
like SDMMC1/Ethernet pinmux, LED naming were wrong. This was due to the fact the
board was on early bringup stage and I couldn't test Ethernet due to my setup
issue at that time (yeah I know it is bad). Also, I don't get access to DHCOR
schematics as well for things like PMIC. Do you have access to it? If possible
can you share a link to that if available publicly?
I will test this series and also the uboot one on my board and give my
Tested-by tag soon.
Anyway, I think the patchset subject could be something like,
"Improve AV96 support" :)
Thanks,
Mani
> Marek Vasut (22):
> ARM: dts: stm32: Add alternate pinmux for ethernet RGMII
> ARM: dts: stm32: Repair ethernet operation on AV96
> ARM: dts: stm32: Add missing ethernet PHY reset on AV96
> ARM: dts: stm32: Add missing ethernet PHY skews on AV96
> ARM: dts: stm32: Add alternate pinmux for SDMMC1 direction pins
> ARM: dts: stm32: Repair SDMMC1 operation on AV96
> ARM: dts: stm32: Add alternate pinmux for SDMMC2 pins 4-7
> ARM: dts: stm32: Add eMMC attached to SDMMC2 on AV96
> ARM: dts: stm32: Repair PMIC configuration on AV96
> ARM: dts: stm32: Repair PMIC interrupt on AV96
> ARM: dts: stm32: Add QSPI NOR on AV96
> ARM: dts: stm32: Add configuration EEPROM on AV96
> ARM: dts: stm32: Enable GPU on AV96
> ARM: dts: stm32: Add alternate pinmux for SDMMC3 pins
> ARM: dts: stm32: Enable WiFi on AV96
> ARM: dts: stm32: Add alternate pinmux for USART2 pins
> ARM: dts: stm32: Enable Bluetooth on AV96
> ARM: dts: stm32: Add alternate pinmux for LTDC pins
> ARM: dts: stm32: Add bindings for HDMI video on AV96
> ARM: dts: stm32: Add bindings for audio on AV96
> ARM: dts: stm32: Add bindings for USB on AV96
> ARM: dts: stm32: Rename LEDs to match silkscreen on AV96
>
> arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 248 +++++++++++++++
> arch/arm/boot/dts/stm32mp157a-avenger96.dts | 328 ++++++++++++++++++--
> 2 files changed, 543 insertions(+), 33 deletions(-)
>
> Cc: Alexandre Torgue <alexandre.torgue@st.com>
> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
> Cc: Patrice Chotard <patrice.chotard@st.com>
> Cc: Patrick Delaunay <patrick.delaunay@st.com>
> Cc: linux-stm32@st-md-mailman.stormreply.com
> To: linux-arm-kernel@lists.infradead.org
>
> --
> 2.25.1
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH V2 22/22] ARM: dts: stm32: Rename LEDs to match silkscreen on AV96
2020-03-31 0:57 ` [PATCH V2 22/22] ARM: dts: stm32: Rename LEDs to match silkscreen " Marek Vasut
@ 2020-03-31 4:09 ` Manivannan Sadhasivam
0 siblings, 0 replies; 46+ messages in thread
From: Manivannan Sadhasivam @ 2020-03-31 4:09 UTC (permalink / raw)
To: Marek Vasut
Cc: Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, linux-stm32, linux-arm-kernel
On Tue, Mar 31, 2020 at 02:57:01AM +0200, Marek Vasut wrote:
> The LED labels do not match the silkscreen on the board, fix it.
>
Yikes, sorry for missing this earlier.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Thanks,
Mani
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Alexandre Torgue <alexandre.torgue@st.com>
> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
> Cc: Patrice Chotard <patrice.chotard@st.com>
> Cc: Patrick Delaunay <patrick.delaunay@st.com>
> Cc: linux-stm32@st-md-mailman.stormreply.com
> To: linux-arm-kernel@lists.infradead.org
> ---
> V2: No change
> ---
> arch/arm/boot/dts/stm32mp157a-avenger96.dts | 6 +++---
> 1 file changed, 3 insertions(+), 3 deletions(-)
>
> diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
> index b6cb3b2d8c78..4291a97cc05f 100644
> --- a/arch/arm/boot/dts/stm32mp157a-avenger96.dts
> +++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
> @@ -55,21 +55,21 @@ memory@c0000000 {
> led {
> compatible = "gpio-leds";
> led1 {
> - label = "green:user1";
> + label = "green:user0";
> gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>;
> linux,default-trigger = "heartbeat";
> default-state = "off";
> };
>
> led2 {
> - label = "green:user2";
> + label = "green:user1";
> gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>;
> linux,default-trigger = "mmc0";
> default-state = "off";
> };
>
> led3 {
> - label = "green:user3";
> + label = "green:user2";
> gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>;
> linux,default-trigger = "mmc1";
> default-state = "off";
> --
> 2.25.1
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH V2 01/22] ARM: dts: stm32: Add alternate pinmux for ethernet RGMII
2020-03-31 0:56 ` [PATCH V2 01/22] ARM: dts: stm32: Add alternate pinmux for ethernet RGMII Marek Vasut
@ 2020-03-31 4:13 ` Manivannan Sadhasivam
0 siblings, 0 replies; 46+ messages in thread
From: Manivannan Sadhasivam @ 2020-03-31 4:13 UTC (permalink / raw)
To: Marek Vasut
Cc: Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, linux-stm32, linux-arm-kernel
On Tue, Mar 31, 2020 at 02:56:40AM +0200, Marek Vasut wrote:
> Add another mux option for DWMAC RGMII, this is used on AV96 board.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Thanks,
Mani
> Cc: Alexandre Torgue <alexandre.torgue@st.com>
> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
> Cc: Patrice Chotard <patrice.chotard@st.com>
> Cc: Patrick Delaunay <patrick.delaunay@st.com>
> Cc: linux-stm32@st-md-mailman.stormreply.com
> To: linux-arm-kernel@lists.infradead.org
> ---
> V2: No change
> ---
> arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 51 ++++++++++++++++++++++++
> 1 file changed, 51 insertions(+)
>
> diff --git a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
> index 73c07f0dfad2..4569dc16e5a1 100644
> --- a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
> +++ b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
> @@ -196,6 +196,57 @@ pins1 {
> };
> };
>
> + ethernet0_rgmii_pins_b: rgmii-1 {
> + pins1 {
> + pinmux = <STM32_PINMUX('G', 5, AF11)>, /* ETH_RGMII_CLK125 */
> + <STM32_PINMUX('G', 4, AF11)>, /* ETH_RGMII_GTX_CLK */
> + <STM32_PINMUX('B', 12, AF11)>, /* ETH_RGMII_TXD0 */
> + <STM32_PINMUX('G', 14, AF11)>, /* ETH_RGMII_TXD1 */
> + <STM32_PINMUX('C', 2, AF11)>, /* ETH_RGMII_TXD2 */
> + <STM32_PINMUX('E', 2, AF11)>, /* ETH_RGMII_TXD3 */
> + <STM32_PINMUX('G', 11, AF11)>, /* ETH_RGMII_TX_CTL */
> + <STM32_PINMUX('C', 1, AF11)>; /* ETH_MDC */
> + bias-disable;
> + drive-push-pull;
> + slew-rate = <2>;
> + };
> + pins2 {
> + pinmux = <STM32_PINMUX('A', 2, AF11)>; /* ETH_MDIO */
> + bias-disable;
> + drive-push-pull;
> + slew-rate = <0>;
> + };
> + pins3 {
> + pinmux = <STM32_PINMUX('C', 4, AF11)>, /* ETH_RGMII_RXD0 */
> + <STM32_PINMUX('C', 5, AF11)>, /* ETH_RGMII_RXD1 */
> + <STM32_PINMUX('H', 6, AF11)>, /* ETH_RGMII_RXD2 */
> + <STM32_PINMUX('B', 1, AF11)>, /* ETH_RGMII_RXD3 */
> + <STM32_PINMUX('A', 1, AF11)>, /* ETH_RGMII_RX_CLK */
> + <STM32_PINMUX('A', 7, AF11)>; /* ETH_RGMII_RX_CTL */
> + bias-disable;
> + };
> + };
> +
> + ethernet0_rgmii_pins_sleep_b: rgmii-sleep-1 {
> + pins1 {
> + pinmux = <STM32_PINMUX('G', 5, ANALOG)>, /* ETH_RGMII_CLK125 */
> + <STM32_PINMUX('G', 4, ANALOG)>, /* ETH_RGMII_GTX_CLK */
> + <STM32_PINMUX('B', 12, ANALOG)>, /* ETH_RGMII_TXD0 */
> + <STM32_PINMUX('G', 14, ANALOG)>, /* ETH_RGMII_TXD1 */
> + <STM32_PINMUX('C', 2, ANALOG)>, /* ETH_RGMII_TXD2 */
> + <STM32_PINMUX('E', 2, ANALOG)>, /* ETH_RGMII_TXD3 */
> + <STM32_PINMUX('G', 11, ANALOG)>, /* ETH_RGMII_TX_CTL */
> + <STM32_PINMUX('A', 2, ANALOG)>, /* ETH_MDIO */
> + <STM32_PINMUX('C', 1, ANALOG)>, /* ETH_MDC */
> + <STM32_PINMUX('C', 4, ANALOG)>, /* ETH_RGMII_RXD0 */
> + <STM32_PINMUX('C', 5, ANALOG)>, /* ETH_RGMII_RXD1 */
> + <STM32_PINMUX('H', 6, ANALOG)>, /* ETH_RGMII_RXD2 */
> + <STM32_PINMUX('B', 1, ANALOG)>, /* ETH_RGMII_RXD3 */
> + <STM32_PINMUX('A', 1, ANALOG)>, /* ETH_RGMII_RX_CLK */
> + <STM32_PINMUX('A', 7, ANALOG)>; /* ETH_RGMII_RX_CTL */
> + };
> + };
> +
> fmc_pins_a: fmc-0 {
> pins1 {
> pinmux = <STM32_PINMUX('D', 4, AF12)>, /* FMC_NOE */
> --
> 2.25.1
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH V2 02/22] ARM: dts: stm32: Repair ethernet operation on AV96
2020-03-31 0:56 ` [PATCH V2 02/22] ARM: dts: stm32: Repair ethernet operation on AV96 Marek Vasut
@ 2020-03-31 4:13 ` Manivannan Sadhasivam
0 siblings, 0 replies; 46+ messages in thread
From: Manivannan Sadhasivam @ 2020-03-31 4:13 UTC (permalink / raw)
To: Marek Vasut
Cc: Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, linux-stm32, linux-arm-kernel
On Tue, Mar 31, 2020 at 02:56:41AM +0200, Marek Vasut wrote:
> The AV96 RGMII uses different pinmux for ETH_RGMII_TXD0, ETH_RGMII_RXD2
> and ETH_RGMII_TX_CTL. Use the correct pinmux to make ethernet operational.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Thanks,
Mani
> Cc: Alexandre Torgue <alexandre.torgue@st.com>
> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
> Cc: Patrice Chotard <patrice.chotard@st.com>
> Cc: Patrick Delaunay <patrick.delaunay@st.com>
> Cc: linux-stm32@st-md-mailman.stormreply.com
> To: linux-arm-kernel@lists.infradead.org
> ---
> V2: No change
> ---
> arch/arm/boot/dts/stm32mp157a-avenger96.dts | 4 ++--
> 1 file changed, 2 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
> index 425175f7d83c..1d15b745feeb 100644
> --- a/arch/arm/boot/dts/stm32mp157a-avenger96.dts
> +++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
> @@ -81,8 +81,8 @@ led6 {
>
> ðernet0 {
> status = "okay";
> - pinctrl-0 = <ðernet0_rgmii_pins_a>;
> - pinctrl-1 = <ðernet0_rgmii_pins_sleep_a>;
> + pinctrl-0 = <ðernet0_rgmii_pins_b>;
> + pinctrl-1 = <ðernet0_rgmii_pins_sleep_b>;
> pinctrl-names = "default", "sleep";
> phy-mode = "rgmii";
> max-speed = <1000>;
> --
> 2.25.1
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH V2 03/22] ARM: dts: stm32: Add missing ethernet PHY reset on AV96
2020-03-31 0:56 ` [PATCH V2 03/22] ARM: dts: stm32: Add missing ethernet PHY reset " Marek Vasut
@ 2020-03-31 4:21 ` Manivannan Sadhasivam
0 siblings, 0 replies; 46+ messages in thread
From: Manivannan Sadhasivam @ 2020-03-31 4:21 UTC (permalink / raw)
To: Marek Vasut
Cc: Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, linux-stm32, linux-arm-kernel
On Tue, Mar 31, 2020 at 02:56:42AM +0200, Marek Vasut wrote:
> Add PHY reset GPIO on AV96 ethernet PHY.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Alexandre Torgue <alexandre.torgue@st.com>
> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
> Cc: Patrice Chotard <patrice.chotard@st.com>
> Cc: Patrick Delaunay <patrick.delaunay@st.com>
> Cc: linux-stm32@st-md-mailman.stormreply.com
> To: linux-arm-kernel@lists.infradead.org
> ---
> V2: No change
> ---
> arch/arm/boot/dts/stm32mp157a-avenger96.dts | 2 ++
> 1 file changed, 2 insertions(+)
>
> diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
> index 1d15b745feeb..a568d3824cb0 100644
> --- a/arch/arm/boot/dts/stm32mp157a-avenger96.dts
> +++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
> @@ -87,6 +87,8 @@ ðernet0 {
> phy-mode = "rgmii";
> max-speed = <1000>;
> phy-handle = <&phy0>;
> + phy-reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
> + phy-reset-duration = <100>;
I don't think "phy-reset-duration" property is used by the ethernet controller
driver.
Other than this,
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Thanks,
Mani
>
> mdio0 {
> #address-cells = <1>;
> --
> 2.25.1
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH V2 04/22] ARM: dts: stm32: Add missing ethernet PHY skews on AV96
2020-03-31 0:56 ` [PATCH V2 04/22] ARM: dts: stm32: Add missing ethernet PHY skews " Marek Vasut
@ 2020-03-31 4:22 ` Manivannan Sadhasivam
0 siblings, 0 replies; 46+ messages in thread
From: Manivannan Sadhasivam @ 2020-03-31 4:22 UTC (permalink / raw)
To: Marek Vasut
Cc: Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, linux-stm32, linux-arm-kernel
On Tue, Mar 31, 2020 at 02:56:43AM +0200, Marek Vasut wrote:
> The KS9031 PHY supports configurable PHY skews to compensate for
> the board routing. Fill in the correct values.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Thanks,
Mani
> Cc: Alexandre Torgue <alexandre.torgue@st.com>
> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
> Cc: Patrice Chotard <patrice.chotard@st.com>
> Cc: Patrick Delaunay <patrick.delaunay@st.com>
> Cc: linux-stm32@st-md-mailman.stormreply.com
> To: linux-arm-kernel@lists.infradead.org
> ---
> V2: No change
> ---
> arch/arm/boot/dts/stm32mp157a-avenger96.dts | 14 ++++++++++++++
> 1 file changed, 14 insertions(+)
>
> diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
> index a568d3824cb0..e58653ccb60f 100644
> --- a/arch/arm/boot/dts/stm32mp157a-avenger96.dts
> +++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
> @@ -96,6 +96,20 @@ mdio0 {
> compatible = "snps,dwmac-mdio";
> phy0: ethernet-phy@7 {
> reg = <7>;
> +
> + rxc-skew-ps = <1500>;
> + rxdv-skew-ps = <540>;
> + rxd0-skew-ps = <420>;
> + rxd1-skew-ps = <420>;
> + rxd2-skew-ps = <420>;
> + rxd3-skew-ps = <420>;
> +
> + txc-skew-ps = <1440>;
> + txen-skew-ps = <540>;
> + txd0-skew-ps = <420>;
> + txd1-skew-ps = <420>;
> + txd2-skew-ps = <420>;
> + txd3-skew-ps = <420>;
> };
> };
> };
> --
> 2.25.1
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH V2 05/22] ARM: dts: stm32: Add alternate pinmux for SDMMC1 direction pins
2020-03-31 0:56 ` [PATCH V2 05/22] ARM: dts: stm32: Add alternate pinmux for SDMMC1 direction pins Marek Vasut
@ 2020-03-31 4:28 ` Manivannan Sadhasivam
0 siblings, 0 replies; 46+ messages in thread
From: Manivannan Sadhasivam @ 2020-03-31 4:28 UTC (permalink / raw)
To: Marek Vasut
Cc: Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, linux-stm32, linux-arm-kernel
On Tue, Mar 31, 2020 at 02:56:44AM +0200, Marek Vasut wrote:
> Add another mux option for SDMMC1 direction pins, in particular
> SDMMC1_D123DIR, this is used on AV96 board.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Thanks,
Mani
> Cc: Alexandre Torgue <alexandre.torgue@st.com>
> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
> Cc: Patrice Chotard <patrice.chotard@st.com>
> Cc: Patrick Delaunay <patrick.delaunay@st.com>
> Cc: linux-stm32@st-md-mailman.stormreply.com
> To: linux-arm-kernel@lists.infradead.org
> ---
> V2: Fix SDMMC1_D123DIR AF, should be AF11
> ---
> arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 24 ++++++++++++++++++++++++
> 1 file changed, 24 insertions(+)
>
> diff --git a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
> index 4569dc16e5a1..8ac534c5bdf6 100644
> --- a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
> +++ b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
> @@ -920,6 +920,30 @@ pins {
> };
> };
>
> + sdmmc1_dir_pins_b: sdmmc1-dir-1 {
> + pins1 {
> + pinmux = <STM32_PINMUX('F', 2, AF11)>, /* SDMMC1_D0DIR */
> + <STM32_PINMUX('E', 14, AF11)>, /* SDMMC1_D123DIR */
> + <STM32_PINMUX('B', 9, AF11)>; /* SDMMC1_CDIR */
> + slew-rate = <1>;
> + drive-push-pull;
> + bias-pull-up;
> + };
> + pins2{
> + pinmux = <STM32_PINMUX('E', 4, AF8)>; /* SDMMC1_CKIN */
> + bias-pull-up;
> + };
> + };
> +
> + sdmmc1_dir_sleep_pins_b: sdmmc1-dir-sleep-1 {
> + pins {
> + pinmux = <STM32_PINMUX('F', 2, ANALOG)>, /* SDMMC1_D0DIR */
> + <STM32_PINMUX('E', 14, ANALOG)>, /* SDMMC1_D123DIR */
> + <STM32_PINMUX('B', 9, ANALOG)>, /* SDMMC1_CDIR */
> + <STM32_PINMUX('E', 4, ANALOG)>; /* SDMMC1_CKIN */
> + };
> + };
> +
> sdmmc2_b4_pins_a: sdmmc2-b4-0 {
> pins1 {
> pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
> --
> 2.25.1
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH V2 06/22] ARM: dts: stm32: Repair SDMMC1 operation on AV96
2020-03-31 0:56 ` [PATCH V2 06/22] ARM: dts: stm32: Repair SDMMC1 operation on AV96 Marek Vasut
@ 2020-03-31 4:33 ` Manivannan Sadhasivam
2020-03-31 13:36 ` Marek Vasut
0 siblings, 1 reply; 46+ messages in thread
From: Manivannan Sadhasivam @ 2020-03-31 4:33 UTC (permalink / raw)
To: Marek Vasut
Cc: Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, linux-stm32, linux-arm-kernel
On Tue, Mar 31, 2020 at 02:56:45AM +0200, Marek Vasut wrote:
> The SD uses different pinmux for the D123DIRline, use such a pinmux,
> otherwise there is a pinmux collision on the AV96. Add missing SD
> voltage regulator switch.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Alexandre Torgue <alexandre.torgue@st.com>
> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
> Cc: Patrice Chotard <patrice.chotard@st.com>
> Cc: Patrick Delaunay <patrick.delaunay@st.com>
> Cc: linux-stm32@st-md-mailman.stormreply.com
> To: linux-arm-kernel@lists.infradead.org
> ---
> V2: Disable SDR104, it seems unstable thus far
> ---
> arch/arm/boot/dts/stm32mp157a-avenger96.dts | 21 ++++++++++++++++++---
> 1 file changed, 18 insertions(+), 3 deletions(-)
>
> diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
> index e58653ccb60f..04280353fdbe 100644
> --- a/arch/arm/boot/dts/stm32mp157a-avenger96.dts
> +++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
> @@ -77,6 +77,20 @@ led6 {
> default-state = "off";
> };
> };
> +
> + sd_switch: regulator-sd_switch {
> + compatible = "regulator-gpio";
> + regulator-name = "sd_switch";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <2900000>;
> + regulator-type = "voltage";
> + regulator-always-on;
> +
> + gpios = <&gpioi 5 GPIO_ACTIVE_HIGH>;
> + gpios-states = <0>;
> + states = <1800000 0x1>,
> + <2900000 0x0>;
> + };
> };
>
> ðernet0 {
> @@ -305,9 +319,9 @@ &rtc {
>
> &sdmmc1 {
> pinctrl-names = "default", "opendrain", "sleep";
> - pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
> - pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
> - pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
> + pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>;
> + pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_b>;
> + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_b>;
> cd-gpios = <&gpioi 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
The "cd-gpios" change is not present in mainline. I think you can add it to
this patch as well with relevant commit description.
With that fixed,
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Thanks,
Mani
> disable-wp;
> st,sig-dir;
> @@ -315,6 +329,7 @@ &sdmmc1 {
> st,use-ckin;
> bus-width = <4>;
> vmmc-supply = <&vdd_sd>;
> + vqmmc-supply = <&sd_switch>;
> status = "okay";
> };
>
> --
> 2.25.1
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH V2 07/22] ARM: dts: stm32: Add alternate pinmux for SDMMC2 pins 4-7
2020-03-31 0:56 ` [PATCH V2 07/22] ARM: dts: stm32: Add alternate pinmux for SDMMC2 pins 4-7 Marek Vasut
@ 2020-03-31 4:36 ` Manivannan Sadhasivam
0 siblings, 0 replies; 46+ messages in thread
From: Manivannan Sadhasivam @ 2020-03-31 4:36 UTC (permalink / raw)
To: Marek Vasut
Cc: Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, linux-stm32, linux-arm-kernel
On Tue, Mar 31, 2020 at 02:56:46AM +0200, Marek Vasut wrote:
> Add another mux option for SDMMC2 pins 4..7, this is used on AV96 board.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Thanks,
Mani
> Cc: Alexandre Torgue <alexandre.torgue@st.com>
> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
> Cc: Patrice Chotard <patrice.chotard@st.com>
> Cc: Patrick Delaunay <patrick.delaunay@st.com>
> Cc: linux-stm32@st-md-mailman.stormreply.com
> To: linux-arm-kernel@lists.infradead.org
> ---
> V2: No change
> ---
> arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 21 +++++++++++++++++++++
> 1 file changed, 21 insertions(+)
>
> diff --git a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
> index 8ac534c5bdf6..ec3621e0ff08 100644
> --- a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
> +++ b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
> @@ -1062,6 +1062,27 @@ pins {
> };
> };
>
> + sdmmc2_d47_pins_b: sdmmc2-d47-1 {
> + pins {
> + pinmux = <STM32_PINMUX('A', 8, AF9)>, /* SDMMC2_D4 */
> + <STM32_PINMUX('A', 15, AF9)>, /* SDMMC2_D5 */
> + <STM32_PINMUX('C', 6, AF10)>, /* SDMMC2_D6 */
> + <STM32_PINMUX('C', 7, AF10)>; /* SDMMC2_D7 */
> + slew-rate = <1>;
> + drive-push-pull;
> + bias-pull-up;
> + };
> + };
> +
> + sdmmc2_d47_sleep_pins_b: sdmmc2-d47-sleep-1 {
> + pins {
> + pinmux = <STM32_PINMUX('A', 8, ANALOG)>, /* SDMMC2_D4 */
> + <STM32_PINMUX('A', 15, ANALOG)>, /* SDMMC2_D5 */
> + <STM32_PINMUX('C', 6, ANALOG)>, /* SDMMC2_D6 */
> + <STM32_PINMUX('C', 7, ANALOG)>; /* SDMMC2_D7 */
> + };
> + };
> +
> sdmmc3_b4_pins_a: sdmmc3-b4-0 {
> pins1 {
> pinmux = <STM32_PINMUX('F', 0, AF9)>, /* SDMMC3_D0 */
> --
> 2.25.1
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH V2 08/22] ARM: dts: stm32: Add eMMC attached to SDMMC2 on AV96
2020-03-31 0:56 ` [PATCH V2 08/22] ARM: dts: stm32: Add eMMC attached to SDMMC2 on AV96 Marek Vasut
@ 2020-03-31 4:43 ` Manivannan Sadhasivam
2020-03-31 15:46 ` Marek Vasut
0 siblings, 1 reply; 46+ messages in thread
From: Manivannan Sadhasivam @ 2020-03-31 4:43 UTC (permalink / raw)
To: Marek Vasut
Cc: Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, linux-stm32, linux-arm-kernel
On Tue, Mar 31, 2020 at 02:56:47AM +0200, Marek Vasut wrote:
> Add DT node describing the eMMC attached to SDMMC2 controller
> of the STM32MP1 on DHCOR SoM, which is the SoM soldered on AV96.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Alexandre Torgue <alexandre.torgue@st.com>
> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
> Cc: Patrice Chotard <patrice.chotard@st.com>
> Cc: Patrick Delaunay <patrick.delaunay@st.com>
> Cc: linux-stm32@st-md-mailman.stormreply.com
> To: linux-arm-kernel@lists.infradead.org
> ---
> V2: No change
> ---
> arch/arm/boot/dts/stm32mp157a-avenger96.dts | 15 +++++++++++++++
> 1 file changed, 15 insertions(+)
>
> diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
> index 04280353fdbe..6c34a003c3f6 100644
> --- a/arch/arm/boot/dts/stm32mp157a-avenger96.dts
> +++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
> @@ -333,6 +333,21 @@ &sdmmc1 {
> status = "okay";
> };
>
> +&sdmmc2 {
> + pinctrl-names = "default", "opendrain", "sleep";
> + pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>;
> + pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_b>;
> + pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_b>;
> + bus-width = <8>;
> + mmc-ddr-1_8v;
> + no-sd;
> + no-sdio;
> + non-removable;
> + st,neg-edge;
> + vmmc-supply = <&v1v8>;
As per the latest schematics, vmmc supply is 3v3 and vqmmc supply is 1v8.
With that fixed,
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Thanks,
Mani
> + status = "okay";
> +};
> +
> &uart4 {
> /* On Low speed expansion header */
> label = "LS-UART1";
> --
> 2.25.1
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH V2 12/22] ARM: dts: stm32: Add configuration EEPROM on AV96
2020-03-31 0:56 ` [PATCH V2 12/22] ARM: dts: stm32: Add configuration EEPROM " Marek Vasut
@ 2020-03-31 6:34 ` Manivannan Sadhasivam
0 siblings, 0 replies; 46+ messages in thread
From: Manivannan Sadhasivam @ 2020-03-31 6:34 UTC (permalink / raw)
To: Marek Vasut
Cc: Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, linux-stm32, linux-arm-kernel
On Tue, Mar 31, 2020 at 02:56:51AM +0200, Marek Vasut wrote:
> The board has an EEPROM on the same I2C bus as PMIC, at address 0x53.
> The EEPROM contains the board MAC address.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Thanks,
Mani
> Cc: Alexandre Torgue <alexandre.torgue@st.com>
> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
> Cc: Patrice Chotard <patrice.chotard@st.com>
> Cc: Patrick Delaunay <patrick.delaunay@st.com>
> Cc: linux-stm32@st-md-mailman.stormreply.com
> To: linux-arm-kernel@lists.infradead.org
> ---
> V2: No change
> ---
> arch/arm/boot/dts/stm32mp157a-avenger96.dts | 6 ++++++
> 1 file changed, 6 insertions(+)
>
> diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
> index de347453db6c..3dfc51f65709 100644
> --- a/arch/arm/boot/dts/stm32mp157a-avenger96.dts
> +++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
> @@ -302,6 +302,12 @@ watchdog {
> status = "disabled";
> };
> };
> +
> + eeprom@53 {
> + compatible = "atmel,24c02";
> + reg = <0x53>;
> + pagesize = <16>;
> + };
> };
>
> &iwdg2 {
> --
> 2.25.1
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH V2 13/22] ARM: dts: stm32: Enable GPU on AV96
2020-03-31 0:56 ` [PATCH V2 13/22] ARM: dts: stm32: Enable GPU " Marek Vasut
@ 2020-03-31 6:36 ` Manivannan Sadhasivam
0 siblings, 0 replies; 46+ messages in thread
From: Manivannan Sadhasivam @ 2020-03-31 6:36 UTC (permalink / raw)
To: Marek Vasut
Cc: Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, linux-stm32, linux-arm-kernel
On Tue, Mar 31, 2020 at 02:56:52AM +0200, Marek Vasut wrote:
> Enable the GPU present on the STM32MP1 populated on AV96.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Thanks,
Mani
> Cc: Alexandre Torgue <alexandre.torgue@st.com>
> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
> Cc: Patrice Chotard <patrice.chotard@st.com>
> Cc: Patrick Delaunay <patrick.delaunay@st.com>
> Cc: linux-stm32@st-md-mailman.stormreply.com
> To: linux-arm-kernel@lists.infradead.org
> ---
> V2: No change
> ---
> arch/arm/boot/dts/stm32mp157a-avenger96.dts | 4 ++++
> 1 file changed, 4 insertions(+)
>
> diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
> index 3dfc51f65709..3aeb3afa37d9 100644
> --- a/arch/arm/boot/dts/stm32mp157a-avenger96.dts
> +++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
> @@ -140,6 +140,10 @@ phy0: ethernet-phy@7 {
> };
> };
>
> +&gpu {
> + status = "okay";
> +};
> +
> &i2c1 {
> pinctrl-names = "default";
> pinctrl-0 = <&i2c1_pins_b>;
> --
> 2.25.1
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH V2 14/22] ARM: dts: stm32: Add alternate pinmux for SDMMC3 pins
2020-03-31 0:56 ` [PATCH V2 14/22] ARM: dts: stm32: Add alternate pinmux for SDMMC3 pins Marek Vasut
@ 2020-03-31 6:40 ` Manivannan Sadhasivam
0 siblings, 0 replies; 46+ messages in thread
From: Manivannan Sadhasivam @ 2020-03-31 6:40 UTC (permalink / raw)
To: Marek Vasut
Cc: Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, linux-stm32, linux-arm-kernel
On Tue, Mar 31, 2020 at 02:56:53AM +0200, Marek Vasut wrote:
> Add another mux option for SDMMC3 pins, in particular PD5_SDMMC3_D2 and
> PD0_SDMMC3_CMD, this is used on AV96 board.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Thanks,
Mani
> Cc: Alexandre Torgue <alexandre.torgue@st.com>
> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
> Cc: Patrice Chotard <patrice.chotard@st.com>
> Cc: Patrick Delaunay <patrick.delaunay@st.com>
> Cc: linux-stm32@st-md-mailman.stormreply.com
> To: linux-arm-kernel@lists.infradead.org
> ---
> V2: No change
> ---
> arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 54 ++++++++++++++++++++++++
> 1 file changed, 54 insertions(+)
>
> diff --git a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
> index ec3621e0ff08..f3f9fc4a3503 100644
> --- a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
> +++ b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
> @@ -1137,6 +1137,60 @@ pins {
> };
> };
>
> + sdmmc3_b4_pins_b: sdmmc3-b4-1 {
> + pins1 {
> + pinmux = <STM32_PINMUX('F', 0, AF9)>, /* SDMMC3_D0 */
> + <STM32_PINMUX('F', 4, AF9)>, /* SDMMC3_D1 */
> + <STM32_PINMUX('D', 5, AF10)>, /* SDMMC3_D2 */
> + <STM32_PINMUX('D', 7, AF10)>, /* SDMMC3_D3 */
> + <STM32_PINMUX('D', 0, AF10)>; /* SDMMC3_CMD */
> + slew-rate = <1>;
> + drive-push-pull;
> + bias-pull-up;
> + };
> + pins2 {
> + pinmux = <STM32_PINMUX('G', 15, AF10)>; /* SDMMC3_CK */
> + slew-rate = <2>;
> + drive-push-pull;
> + bias-pull-up;
> + };
> + };
> +
> + sdmmc3_b4_od_pins_b: sdmmc3-b4-od-1 {
> + pins1 {
> + pinmux = <STM32_PINMUX('F', 0, AF9)>, /* SDMMC3_D0 */
> + <STM32_PINMUX('F', 4, AF9)>, /* SDMMC3_D1 */
> + <STM32_PINMUX('D', 5, AF10)>, /* SDMMC3_D2 */
> + <STM32_PINMUX('D', 7, AF10)>; /* SDMMC3_D3 */
> + slew-rate = <1>;
> + drive-push-pull;
> + bias-pull-up;
> + };
> + pins2 {
> + pinmux = <STM32_PINMUX('G', 15, AF10)>; /* SDMMC3_CK */
> + slew-rate = <2>;
> + drive-push-pull;
> + bias-pull-up;
> + };
> + pins3 {
> + pinmux = <STM32_PINMUX('D', 0, AF10)>; /* SDMMC2_CMD */
> + slew-rate = <1>;
> + drive-open-drain;
> + bias-pull-up;
> + };
> + };
> +
> + sdmmc3_b4_sleep_pins_b: sdmmc3-b4-sleep-1 {
> + pins {
> + pinmux = <STM32_PINMUX('F', 0, ANALOG)>, /* SDMMC3_D0 */
> + <STM32_PINMUX('F', 4, ANALOG)>, /* SDMMC3_D1 */
> + <STM32_PINMUX('D', 5, ANALOG)>, /* SDMMC3_D2 */
> + <STM32_PINMUX('D', 7, ANALOG)>, /* SDMMC3_D3 */
> + <STM32_PINMUX('G', 15, ANALOG)>, /* SDMMC3_CK */
> + <STM32_PINMUX('D', 0, ANALOG)>; /* SDMMC3_CMD */
> + };
> + };
> +
> spdifrx_pins_a: spdifrx-0 {
> pins {
> pinmux = <STM32_PINMUX('G', 12, AF8)>; /* SPDIF_IN1 */
> --
> 2.25.1
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH V2 15/22] ARM: dts: stm32: Enable WiFi on AV96
2020-03-31 0:56 ` [PATCH V2 15/22] ARM: dts: stm32: Enable WiFi on AV96 Marek Vasut
@ 2020-03-31 6:43 ` Manivannan Sadhasivam
0 siblings, 0 replies; 46+ messages in thread
From: Manivannan Sadhasivam @ 2020-03-31 6:43 UTC (permalink / raw)
To: Marek Vasut
Cc: Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, linux-stm32, linux-arm-kernel
On Tue, Mar 31, 2020 at 02:56:54AM +0200, Marek Vasut wrote:
> The WiFi/Bluetooth SDIO chip is attached to SDMMC3 on AV96, describe it
> in DT to make it available. Remove WiFi LED and turn it into a regulator,
> because it is a GPIO controlling the WL_REG_ON input of the WiFi chip.
> The LED is just an indicator connected to the same line, but not the
> primary function.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Thanks,
Mani
> Cc: Alexandre Torgue <alexandre.torgue@st.com>
> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
> Cc: Patrice Chotard <patrice.chotard@st.com>
> Cc: Patrick Delaunay <patrick.delaunay@st.com>
> Cc: linux-stm32@st-md-mailman.stormreply.com
> To: linux-arm-kernel@lists.infradead.org
> ---
> V2: No change
> ---
> arch/arm/boot/dts/stm32mp157a-avenger96.dts | 38 +++++++++++++++++----
> 1 file changed, 31 insertions(+), 7 deletions(-)
>
> diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
> index 3aeb3afa37d9..12ee95d5adb1 100644
> --- a/arch/arm/boot/dts/stm32mp157a-avenger96.dts
> +++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
> @@ -65,13 +65,6 @@ led4 {
> };
>
> led5 {
> - label = "yellow:wifi";
> - gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>;
> - linux,default-trigger = "phy0tx";
> - default-state = "off";
> - };
> -
> - led6 {
> label = "blue:bt";
> gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>;
> linux,default-trigger = "bluetooth-power";
> @@ -103,6 +96,17 @@ vdd_io: regulator-buck-io {
> regulator-boot-on;
> vin-supply = <&vdd>;
> };
> +
> + wlan_pwr: regulator-wlan {
> + compatible = "regulator-fixed";
> +
> + regulator-name = "wl-reg";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> +
> + gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> };
>
> ðernet0 {
> @@ -382,6 +386,26 @@ &sdmmc2 {
> status = "okay";
> };
>
> +&sdmmc3 {
> + pinctrl-names = "default", "opendrain", "sleep";
> + pinctrl-0 = <&sdmmc3_b4_pins_b>;
> + pinctrl-1 = <&sdmmc3_b4_od_pins_b>;
> + pinctrl-2 = <&sdmmc3_b4_sleep_pins_b>;
> + broken-cd;
> + non-removable;
> + st,neg-edge;
> + bus-width = <4>;
> + vmmc-supply = <&wlan_pwr>;
> + status = "okay";
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> + brcmf: bcrmf@1 {
> + reg = <1>;
> + compatible = "brcm,bcm4329-fmac";
> + };
> +};
> +
> &uart4 {
> /* On Low speed expansion header */
> label = "LS-UART1";
> --
> 2.25.1
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH V2 16/22] ARM: dts: stm32: Add alternate pinmux for USART2 pins
2020-03-31 0:56 ` [PATCH V2 16/22] ARM: dts: stm32: Add alternate pinmux for USART2 pins Marek Vasut
@ 2020-03-31 6:46 ` Manivannan Sadhasivam
0 siblings, 0 replies; 46+ messages in thread
From: Manivannan Sadhasivam @ 2020-03-31 6:46 UTC (permalink / raw)
To: Marek Vasut
Cc: Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, linux-stm32, linux-arm-kernel
On Tue, Mar 31, 2020 at 02:56:55AM +0200, Marek Vasut wrote:
> Add mux option for USART2 pins, this is used on AV96 board.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Thanks,
Mani
> Cc: Alexandre Torgue <alexandre.torgue@st.com>
> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
> Cc: Patrice Chotard <patrice.chotard@st.com>
> Cc: Patrick Delaunay <patrick.delaunay@st.com>
> Cc: linux-stm32@st-md-mailman.stormreply.com
> To: linux-arm-kernel@lists.infradead.org
> ---
> V2: No change
> ---
> arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 24 ++++++++++++++++++++++++
> 1 file changed, 24 insertions(+)
>
> diff --git a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
> index f3f9fc4a3503..4f3b40d5751f 100644
> --- a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
> +++ b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
> @@ -1204,6 +1204,30 @@ pins {
> };
> };
>
> + usart2_pins_a: usart2-0 {
> + pins1 {
> + pinmux = <STM32_PINMUX('F', 5, AF7)>, /* USART2_TX */
> + <STM32_PINMUX('D', 4, AF7)>; /* USART2_RTS */
> + bias-disable;
> + drive-push-pull;
> + slew-rate = <0>;
> + };
> + pins2 {
> + pinmux = <STM32_PINMUX('D', 6, AF7)>, /* USART2_RX */
> + <STM32_PINMUX('D', 3, AF7)>; /* USART2_CTS_NSS */
> + bias-disable;
> + };
> + };
> +
> + usart2_sleep_pins_a: usart2-sleep-0 {
> + pins {
> + pinmux = <STM32_PINMUX('F', 5, ANALOG)>, /* USART2_TX */
> + <STM32_PINMUX('D', 4, ANALOG)>, /* USART2_RTS */
> + <STM32_PINMUX('D', 6, ANALOG)>, /* USART2_RX */
> + <STM32_PINMUX('D', 3, ANALOG)>; /* USART2_CTS_NSS */
> + };
> + };
> +
> usart3_pins_a: usart3-0 {
> pins1 {
> pinmux = <STM32_PINMUX('B', 10, AF7)>; /* USART3_TX */
> --
> 2.25.1
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH V2 17/22] ARM: dts: stm32: Enable Bluetooth on AV96
2020-03-31 0:56 ` [PATCH V2 17/22] ARM: dts: stm32: Enable Bluetooth on AV96 Marek Vasut
@ 2020-03-31 6:47 ` Manivannan Sadhasivam
0 siblings, 0 replies; 46+ messages in thread
From: Manivannan Sadhasivam @ 2020-03-31 6:47 UTC (permalink / raw)
To: Marek Vasut
Cc: Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, linux-stm32, linux-arm-kernel
On Tue, Mar 31, 2020 at 02:56:56AM +0200, Marek Vasut wrote:
> The WiFi/Bluetooth chip is attached to USART2 on AV96 as well, describe
> it in DT to make it available. Remove BT LED and turn it into a shutdown
> GPIO, because the GPIO line controls the BT_REG_ON signal. The LED is just
> an indicator connected to the same line, but not the primary function.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Thanks,
Mani
> Cc: Alexandre Torgue <alexandre.torgue@st.com>
> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
> Cc: Patrice Chotard <patrice.chotard@st.com>
> Cc: Patrick Delaunay <patrick.delaunay@st.com>
> Cc: linux-stm32@st-md-mailman.stormreply.com
> To: linux-arm-kernel@lists.infradead.org
> ---
> V2: No change
> ---
> arch/arm/boot/dts/stm32mp157a-avenger96.dts | 23 ++++++++++++++-------
> 1 file changed, 16 insertions(+), 7 deletions(-)
>
> diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
> index 12ee95d5adb1..29af5ed2ebb3 100644
> --- a/arch/arm/boot/dts/stm32mp157a-avenger96.dts
> +++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
> @@ -21,6 +21,7 @@ aliases {
> mmc0 = &sdmmc1;
> serial0 = &uart4;
> serial1 = &uart7;
> + serial2 = &usart2;
> spi0 = &qspi;
> };
>
> @@ -63,13 +64,6 @@ led4 {
> default-state = "off";
> panic-indicator;
> };
> -
> - led5 {
> - label = "blue:bt";
> - gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>;
> - linux,default-trigger = "bluetooth-power";
> - default-state = "off";
> - };
> };
>
> sd_switch: regulator-sd_switch {
> @@ -421,3 +415,18 @@ &uart7 {
> pinctrl-0 = <&uart7_pins_a>;
> status = "okay";
> };
> +
> +/* Bluetooth */
> +&usart2 {
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&usart2_pins_a>;
> + pinctrl-1 = <&usart2_sleep_pins_a>;
> + st,hw-flow-ctrl;
> + status = "okay";
> +
> + bluetooth {
> + compatible = "brcm,bcm43438-bt";
> + max-speed = <3000000>;
> + shutdown-gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>;
> + };
> +};
> --
> 2.25.1
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH V2 06/22] ARM: dts: stm32: Repair SDMMC1 operation on AV96
2020-03-31 4:33 ` Manivannan Sadhasivam
@ 2020-03-31 13:36 ` Marek Vasut
2020-03-31 14:02 ` Manivannan Sadhasivam
0 siblings, 1 reply; 46+ messages in thread
From: Marek Vasut @ 2020-03-31 13:36 UTC (permalink / raw)
To: Manivannan Sadhasivam
Cc: Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, linux-stm32, linux-arm-kernel
On 3/31/20 6:33 AM, Manivannan Sadhasivam wrote:
> On Tue, Mar 31, 2020 at 02:56:45AM +0200, Marek Vasut wrote:
>> The SD uses different pinmux for the D123DIRline, use such a pinmux,
>> otherwise there is a pinmux collision on the AV96. Add missing SD
>> voltage regulator switch.
>>
>> Signed-off-by: Marek Vasut <marex@denx.de>
>> Cc: Alexandre Torgue <alexandre.torgue@st.com>
>> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
>> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
>> Cc: Patrice Chotard <patrice.chotard@st.com>
>> Cc: Patrick Delaunay <patrick.delaunay@st.com>
>> Cc: linux-stm32@st-md-mailman.stormreply.com
>> To: linux-arm-kernel@lists.infradead.org
>> ---
>> V2: Disable SDR104, it seems unstable thus far
>> ---
>> arch/arm/boot/dts/stm32mp157a-avenger96.dts | 21 ++++++++++++++++++---
>> 1 file changed, 18 insertions(+), 3 deletions(-)
>>
>> diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
>> index e58653ccb60f..04280353fdbe 100644
>> --- a/arch/arm/boot/dts/stm32mp157a-avenger96.dts
>> +++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
>> @@ -77,6 +77,20 @@ led6 {
>> default-state = "off";
>> };
>> };
>> +
>> + sd_switch: regulator-sd_switch {
>> + compatible = "regulator-gpio";
>> + regulator-name = "sd_switch";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <2900000>;
>> + regulator-type = "voltage";
>> + regulator-always-on;
>> +
>> + gpios = <&gpioi 5 GPIO_ACTIVE_HIGH>;
>> + gpios-states = <0>;
>> + states = <1800000 0x1>,
>> + <2900000 0x0>;
>> + };
>> };
>>
>> ðernet0 {
>> @@ -305,9 +319,9 @@ &rtc {
>>
>> &sdmmc1 {
>> pinctrl-names = "default", "opendrain", "sleep";
>> - pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
>> - pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
>> - pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
>> + pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>;
>> + pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_b>;
>> + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_b>;
>> cd-gpios = <&gpioi 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
>
> The "cd-gpios" change is not present in mainline. I think you can add it to
> this patch as well with relevant commit description.
What change to cd-gpios ? This patch doesn't change cd-gpios.
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH V2 00/22] ARM: dts: stm32: Repair AV96 board
2020-03-31 4:07 ` [PATCH V2 00/22] ARM: dts: stm32: Repair AV96 board Manivannan Sadhasivam
@ 2020-03-31 13:44 ` Marek Vasut
2020-03-31 14:09 ` Manivannan Sadhasivam
0 siblings, 1 reply; 46+ messages in thread
From: Marek Vasut @ 2020-03-31 13:44 UTC (permalink / raw)
To: Manivannan Sadhasivam
Cc: Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, linux-stm32, linux-arm-kernel
On 3/31/20 6:07 AM, Manivannan Sadhasivam wrote:
> Hi Marek,
Hi,
> Thanks for the series.
>
> On Tue, Mar 31, 2020 at 02:56:39AM +0200, Marek Vasut wrote:
>> The AV96 board device tree is completely broken and does not match the
>> hardware. This series fixes it up.
>>
>
> Completely broken?
The board didn't even boot.
> The patch submitted previously was an initial one and there
> were many interfaces not enabled. I agree that there are few _obvious_ things
> like SDMMC1/Ethernet pinmux, LED naming were wrong. This was due to the fact the
> board was on early bringup stage and I couldn't test Ethernet due to my setup
> issue at that time (yeah I know it is bad). Also, I don't get access to DHCOR
> schematics as well for things like PMIC. Do you have access to it?
Yes, I do have access.
> If possible can you share a link to that if available publicly?
The SoM schematic is not available in public, no, sorry.
> I will test this series and also the uboot one on my board and give my
> Tested-by tag soon.
>
> Anyway, I think the patchset subject could be something like,
> "Improve AV96 support" :)
I think if something doesn't work, "Repair" is the right word for it.
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH V2 06/22] ARM: dts: stm32: Repair SDMMC1 operation on AV96
2020-03-31 13:36 ` Marek Vasut
@ 2020-03-31 14:02 ` Manivannan Sadhasivam
2020-03-31 15:45 ` Marek Vasut
0 siblings, 1 reply; 46+ messages in thread
From: Manivannan Sadhasivam @ 2020-03-31 14:02 UTC (permalink / raw)
To: Marek Vasut
Cc: Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, linux-stm32, linux-arm-kernel
On Tue, Mar 31, 2020 at 03:36:34PM +0200, Marek Vasut wrote:
> On 3/31/20 6:33 AM, Manivannan Sadhasivam wrote:
> > On Tue, Mar 31, 2020 at 02:56:45AM +0200, Marek Vasut wrote:
> >> The SD uses different pinmux for the D123DIRline, use such a pinmux,
> >> otherwise there is a pinmux collision on the AV96. Add missing SD
> >> voltage regulator switch.
> >>
> >> Signed-off-by: Marek Vasut <marex@denx.de>
> >> Cc: Alexandre Torgue <alexandre.torgue@st.com>
> >> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> >> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
> >> Cc: Patrice Chotard <patrice.chotard@st.com>
> >> Cc: Patrick Delaunay <patrick.delaunay@st.com>
> >> Cc: linux-stm32@st-md-mailman.stormreply.com
> >> To: linux-arm-kernel@lists.infradead.org
> >> ---
> >> V2: Disable SDR104, it seems unstable thus far
> >> ---
> >> arch/arm/boot/dts/stm32mp157a-avenger96.dts | 21 ++++++++++++++++++---
> >> 1 file changed, 18 insertions(+), 3 deletions(-)
> >>
> >> diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
> >> index e58653ccb60f..04280353fdbe 100644
> >> --- a/arch/arm/boot/dts/stm32mp157a-avenger96.dts
> >> +++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
> >> @@ -77,6 +77,20 @@ led6 {
> >> default-state = "off";
> >> };
> >> };
> >> +
> >> + sd_switch: regulator-sd_switch {
> >> + compatible = "regulator-gpio";
> >> + regulator-name = "sd_switch";
> >> + regulator-min-microvolt = <1800000>;
> >> + regulator-max-microvolt = <2900000>;
> >> + regulator-type = "voltage";
> >> + regulator-always-on;
> >> +
> >> + gpios = <&gpioi 5 GPIO_ACTIVE_HIGH>;
> >> + gpios-states = <0>;
> >> + states = <1800000 0x1>,
> >> + <2900000 0x0>;
> >> + };
> >> };
> >>
> >> ðernet0 {
> >> @@ -305,9 +319,9 @@ &rtc {
> >>
> >> &sdmmc1 {
> >> pinctrl-names = "default", "opendrain", "sleep";
> >> - pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
> >> - pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
> >> - pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
> >> + pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>;
> >> + pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_b>;
> >> + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_b>;
> >> cd-gpios = <&gpioi 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
> >
> > The "cd-gpios" change is not present in mainline. I think you can add it to
> > this patch as well with relevant commit description.
>
> What change to cd-gpios ? This patch doesn't change cd-gpios.
This cd-gpios change is not present in mainline and also there seems to be few
other properties which got added (probably by another patch?). So this doesn't
apply on top of mainline/master.
Thanks,
Mani
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH V2 00/22] ARM: dts: stm32: Repair AV96 board
2020-03-31 13:44 ` Marek Vasut
@ 2020-03-31 14:09 ` Manivannan Sadhasivam
2020-03-31 15:51 ` Marek Vasut
0 siblings, 1 reply; 46+ messages in thread
From: Manivannan Sadhasivam @ 2020-03-31 14:09 UTC (permalink / raw)
To: Marek Vasut
Cc: Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, linux-stm32, linux-arm-kernel
On Tue, Mar 31, 2020 at 03:44:52PM +0200, Marek Vasut wrote:
> On 3/31/20 6:07 AM, Manivannan Sadhasivam wrote:
> > Hi Marek,
>
> Hi,
>
> > Thanks for the series.
> >
> > On Tue, Mar 31, 2020 at 02:56:39AM +0200, Marek Vasut wrote:
> >> The AV96 board device tree is completely broken and does not match the
> >> hardware. This series fixes it up.
> >>
> >
> > Completely broken?
>
> The board didn't even boot.
>
Hmm. I think you're using a new revision of AV96. I added the board support
with an old version of it (might be an evaluation one). I don't have the delta
or changeset so can't compare. Anyway, DH started selling new boards and I
think the old ones were discontinued or not made available for purchase so we
don't have to worry about breaking the old one.
> > The patch submitted previously was an initial one and there
> > were many interfaces not enabled. I agree that there are few _obvious_ things
> > like SDMMC1/Ethernet pinmux, LED naming were wrong. This was due to the fact the
> > board was on early bringup stage and I couldn't test Ethernet due to my setup
> > issue at that time (yeah I know it is bad). Also, I don't get access to DHCOR
> > schematics as well for things like PMIC. Do you have access to it?
>
> Yes, I do have access.
>
> > If possible can you share a link to that if available publicly?
>
> The SoM schematic is not available in public, no, sorry.
>
Fine. Just wanted to verify the PMIC part. But I got the information from
DH guy offline.
> > I will test this series and also the uboot one on my board and give my
> > Tested-by tag soon.
> >
> > Anyway, I think the patchset subject could be something like,
> > "Improve AV96 support" :)
>
> I think if something doesn't work, "Repair" is the right word for it.
Right. Didn't know that it doesn't boot on newer boards. I do have one but
haven't tried mainline kernel on it, just vendor image for some demos. But
feel free to keep it as it is.
Thanks,
Mani
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH V2 06/22] ARM: dts: stm32: Repair SDMMC1 operation on AV96
2020-03-31 14:02 ` Manivannan Sadhasivam
@ 2020-03-31 15:45 ` Marek Vasut
0 siblings, 0 replies; 46+ messages in thread
From: Marek Vasut @ 2020-03-31 15:45 UTC (permalink / raw)
To: Manivannan Sadhasivam
Cc: Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, linux-stm32, linux-arm-kernel
On 3/31/20 4:02 PM, Manivannan Sadhasivam wrote:
> On Tue, Mar 31, 2020 at 03:36:34PM +0200, Marek Vasut wrote:
>> On 3/31/20 6:33 AM, Manivannan Sadhasivam wrote:
>>> On Tue, Mar 31, 2020 at 02:56:45AM +0200, Marek Vasut wrote:
>>>> The SD uses different pinmux for the D123DIRline, use such a pinmux,
>>>> otherwise there is a pinmux collision on the AV96. Add missing SD
>>>> voltage regulator switch.
>>>>
>>>> Signed-off-by: Marek Vasut <marex@denx.de>
>>>> Cc: Alexandre Torgue <alexandre.torgue@st.com>
>>>> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
>>>> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
>>>> Cc: Patrice Chotard <patrice.chotard@st.com>
>>>> Cc: Patrick Delaunay <patrick.delaunay@st.com>
>>>> Cc: linux-stm32@st-md-mailman.stormreply.com
>>>> To: linux-arm-kernel@lists.infradead.org
>>>> ---
>>>> V2: Disable SDR104, it seems unstable thus far
>>>> ---
>>>> arch/arm/boot/dts/stm32mp157a-avenger96.dts | 21 ++++++++++++++++++---
>>>> 1 file changed, 18 insertions(+), 3 deletions(-)
>>>>
>>>> diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
>>>> index e58653ccb60f..04280353fdbe 100644
>>>> --- a/arch/arm/boot/dts/stm32mp157a-avenger96.dts
>>>> +++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
>>>> @@ -77,6 +77,20 @@ led6 {
>>>> default-state = "off";
>>>> };
>>>> };
>>>> +
>>>> + sd_switch: regulator-sd_switch {
>>>> + compatible = "regulator-gpio";
>>>> + regulator-name = "sd_switch";
>>>> + regulator-min-microvolt = <1800000>;
>>>> + regulator-max-microvolt = <2900000>;
>>>> + regulator-type = "voltage";
>>>> + regulator-always-on;
>>>> +
>>>> + gpios = <&gpioi 5 GPIO_ACTIVE_HIGH>;
>>>> + gpios-states = <0>;
>>>> + states = <1800000 0x1>,
>>>> + <2900000 0x0>;
>>>> + };
>>>> };
>>>>
>>>> ðernet0 {
>>>> @@ -305,9 +319,9 @@ &rtc {
>>>>
>>>> &sdmmc1 {
>>>> pinctrl-names = "default", "opendrain", "sleep";
>>>> - pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
>>>> - pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
>>>> - pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
>>>> + pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>;
>>>> + pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_b>;
>>>> + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_b>;
>>>> cd-gpios = <&gpioi 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
>>>
>>> The "cd-gpios" change is not present in mainline. I think you can add it to
>>> this patch as well with relevant commit description.
>>
>> What change to cd-gpios ? This patch doesn't change cd-gpios.
>
> This cd-gpios change is not present in mainline and also there seems to be few
> other properties which got added (probably by another patch?). So this doesn't
> apply on top of mainline/master.
This series is based on next/master .
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH V2 08/22] ARM: dts: stm32: Add eMMC attached to SDMMC2 on AV96
2020-03-31 4:43 ` Manivannan Sadhasivam
@ 2020-03-31 15:46 ` Marek Vasut
0 siblings, 0 replies; 46+ messages in thread
From: Marek Vasut @ 2020-03-31 15:46 UTC (permalink / raw)
To: Manivannan Sadhasivam
Cc: Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, linux-stm32, linux-arm-kernel
On 3/31/20 6:43 AM, Manivannan Sadhasivam wrote:
> On Tue, Mar 31, 2020 at 02:56:47AM +0200, Marek Vasut wrote:
>> Add DT node describing the eMMC attached to SDMMC2 controller
>> of the STM32MP1 on DHCOR SoM, which is the SoM soldered on AV96.
>>
>> Signed-off-by: Marek Vasut <marex@denx.de>
>> Cc: Alexandre Torgue <alexandre.torgue@st.com>
>> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
>> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
>> Cc: Patrice Chotard <patrice.chotard@st.com>
>> Cc: Patrick Delaunay <patrick.delaunay@st.com>
>> Cc: linux-stm32@st-md-mailman.stormreply.com
>> To: linux-arm-kernel@lists.infradead.org
>> ---
>> V2: No change
>> ---
>> arch/arm/boot/dts/stm32mp157a-avenger96.dts | 15 +++++++++++++++
>> 1 file changed, 15 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
>> index 04280353fdbe..6c34a003c3f6 100644
>> --- a/arch/arm/boot/dts/stm32mp157a-avenger96.dts
>> +++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
>> @@ -333,6 +333,21 @@ &sdmmc1 {
>> status = "okay";
>> };
>>
>> +&sdmmc2 {
>> + pinctrl-names = "default", "opendrain", "sleep";
>> + pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>;
>> + pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_b>;
>> + pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_b>;
>> + bus-width = <8>;
>> + mmc-ddr-1_8v;
>> + no-sd;
>> + no-sdio;
>> + non-removable;
>> + st,neg-edge;
>> + vmmc-supply = <&v1v8>;
>
> As per the latest schematics, vmmc supply is 3v3 and vqmmc supply is 1v8.
> With that fixed,
Oh sigh, this actually exposes an issue in mmci driver, thanks for
pointing this out.
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 46+ messages in thread
* Re: [PATCH V2 00/22] ARM: dts: stm32: Repair AV96 board
2020-03-31 14:09 ` Manivannan Sadhasivam
@ 2020-03-31 15:51 ` Marek Vasut
0 siblings, 0 replies; 46+ messages in thread
From: Marek Vasut @ 2020-03-31 15:51 UTC (permalink / raw)
To: Manivannan Sadhasivam
Cc: Alexandre Torgue, Patrice Chotard, Patrick Delaunay,
Maxime Coquelin, linux-stm32, linux-arm-kernel
On 3/31/20 4:09 PM, Manivannan Sadhasivam wrote:
> On Tue, Mar 31, 2020 at 03:44:52PM +0200, Marek Vasut wrote:
>> On 3/31/20 6:07 AM, Manivannan Sadhasivam wrote:
>>> Hi Marek,
>>
>> Hi,
>>
>>> Thanks for the series.
>>>
>>> On Tue, Mar 31, 2020 at 02:56:39AM +0200, Marek Vasut wrote:
>>>> The AV96 board device tree is completely broken and does not match the
>>>> hardware. This series fixes it up.
>>>>
>>>
>>> Completely broken?
>>
>> The board didn't even boot.
>>
>
> Hmm. I think you're using a new revision of AV96. I added the board support
> with an old version of it (might be an evaluation one). I don't have the delta
> or changeset so can't compare. Anyway, DH started selling new boards and I
> think the old ones were discontinued or not made available for purchase so we
> don't have to worry about breaking the old one.
I'm sure we can/should support both, lemme ask about this. The baseboard
I have is 588-200 (silkscreen next to barrel jack) and SoM 586-100.
>>> The patch submitted previously was an initial one and there
>>> were many interfaces not enabled. I agree that there are few _obvious_ things
>>> like SDMMC1/Ethernet pinmux, LED naming were wrong. This was due to the fact the
>>> board was on early bringup stage and I couldn't test Ethernet due to my setup
>>> issue at that time (yeah I know it is bad). Also, I don't get access to DHCOR
>>> schematics as well for things like PMIC. Do you have access to it?
>>
>> Yes, I do have access.
>>
>>> If possible can you share a link to that if available publicly?
>>
>> The SoM schematic is not available in public, no, sorry.
>>
>
> Fine. Just wanted to verify the PMIC part. But I got the information from
> DH guy offline.
Yep, I saw that, good.
>>> I will test this series and also the uboot one on my board and give my
>>> Tested-by tag soon.
>>>
>>> Anyway, I think the patchset subject could be something like,
>>> "Improve AV96 support" :)
>>
>> I think if something doesn't work, "Repair" is the right word for it.
>
> Right. Didn't know that it doesn't boot on newer boards. I do have one but
> haven't tried mainline kernel on it, just vendor image for some demos. But
> feel free to keep it as it is.
Do you have the Enpirion regulator on the SoM ? It's between the
STPMIC1A and the SPI NOR.
I'll be sending a V3 shortly (few hours), apply it on next/master if you
want to test:
git://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 46+ messages in thread
end of thread, other threads:[~2020-03-31 16:23 UTC | newest]
Thread overview: 46+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-03-31 0:56 [PATCH V2 00/22] ARM: dts: stm32: Repair AV96 board Marek Vasut
2020-03-31 0:56 ` [PATCH V2 01/22] ARM: dts: stm32: Add alternate pinmux for ethernet RGMII Marek Vasut
2020-03-31 4:13 ` Manivannan Sadhasivam
2020-03-31 0:56 ` [PATCH V2 02/22] ARM: dts: stm32: Repair ethernet operation on AV96 Marek Vasut
2020-03-31 4:13 ` Manivannan Sadhasivam
2020-03-31 0:56 ` [PATCH V2 03/22] ARM: dts: stm32: Add missing ethernet PHY reset " Marek Vasut
2020-03-31 4:21 ` Manivannan Sadhasivam
2020-03-31 0:56 ` [PATCH V2 04/22] ARM: dts: stm32: Add missing ethernet PHY skews " Marek Vasut
2020-03-31 4:22 ` Manivannan Sadhasivam
2020-03-31 0:56 ` [PATCH V2 05/22] ARM: dts: stm32: Add alternate pinmux for SDMMC1 direction pins Marek Vasut
2020-03-31 4:28 ` Manivannan Sadhasivam
2020-03-31 0:56 ` [PATCH V2 06/22] ARM: dts: stm32: Repair SDMMC1 operation on AV96 Marek Vasut
2020-03-31 4:33 ` Manivannan Sadhasivam
2020-03-31 13:36 ` Marek Vasut
2020-03-31 14:02 ` Manivannan Sadhasivam
2020-03-31 15:45 ` Marek Vasut
2020-03-31 0:56 ` [PATCH V2 07/22] ARM: dts: stm32: Add alternate pinmux for SDMMC2 pins 4-7 Marek Vasut
2020-03-31 4:36 ` Manivannan Sadhasivam
2020-03-31 0:56 ` [PATCH V2 08/22] ARM: dts: stm32: Add eMMC attached to SDMMC2 on AV96 Marek Vasut
2020-03-31 4:43 ` Manivannan Sadhasivam
2020-03-31 15:46 ` Marek Vasut
2020-03-31 0:56 ` [PATCH V2 09/22] ARM: dts: stm32: Repair PMIC configuration " Marek Vasut
2020-03-31 0:56 ` [PATCH V2 10/22] ARM: dts: stm32: Repair PMIC interrupt " Marek Vasut
2020-03-31 0:56 ` [PATCH V2 11/22] ARM: dts: stm32: Add QSPI NOR " Marek Vasut
2020-03-31 0:56 ` [PATCH V2 12/22] ARM: dts: stm32: Add configuration EEPROM " Marek Vasut
2020-03-31 6:34 ` Manivannan Sadhasivam
2020-03-31 0:56 ` [PATCH V2 13/22] ARM: dts: stm32: Enable GPU " Marek Vasut
2020-03-31 6:36 ` Manivannan Sadhasivam
2020-03-31 0:56 ` [PATCH V2 14/22] ARM: dts: stm32: Add alternate pinmux for SDMMC3 pins Marek Vasut
2020-03-31 6:40 ` Manivannan Sadhasivam
2020-03-31 0:56 ` [PATCH V2 15/22] ARM: dts: stm32: Enable WiFi on AV96 Marek Vasut
2020-03-31 6:43 ` Manivannan Sadhasivam
2020-03-31 0:56 ` [PATCH V2 16/22] ARM: dts: stm32: Add alternate pinmux for USART2 pins Marek Vasut
2020-03-31 6:46 ` Manivannan Sadhasivam
2020-03-31 0:56 ` [PATCH V2 17/22] ARM: dts: stm32: Enable Bluetooth on AV96 Marek Vasut
2020-03-31 6:47 ` Manivannan Sadhasivam
2020-03-31 0:56 ` [PATCH V2 18/22] ARM: dts: stm32: Add alternate pinmux for LTDC pins Marek Vasut
2020-03-31 0:56 ` [PATCH V2 19/22] ARM: dts: stm32: Add bindings for HDMI video on AV96 Marek Vasut
2020-03-31 0:56 ` [PATCH V2 20/22] ARM: dts: stm32: Add bindings for audio " Marek Vasut
2020-03-31 0:57 ` [PATCH V2 21/22] ARM: dts: stm32: Add bindings for USB " Marek Vasut
2020-03-31 0:57 ` [PATCH V2 22/22] ARM: dts: stm32: Rename LEDs to match silkscreen " Marek Vasut
2020-03-31 4:09 ` Manivannan Sadhasivam
2020-03-31 4:07 ` [PATCH V2 00/22] ARM: dts: stm32: Repair AV96 board Manivannan Sadhasivam
2020-03-31 13:44 ` Marek Vasut
2020-03-31 14:09 ` Manivannan Sadhasivam
2020-03-31 15:51 ` Marek Vasut
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.