* [U-Boot] [PATCH 0/2] Fix broken ethernet on imx8qxp-mek
@ 2019-03-01 13:27 Andrejs Cainikovs
2019-03-01 13:27 ` [U-Boot] [PATCH 1/2] net: dm: fec: Support phy-reset-post-delay property Andrejs Cainikovs
2019-03-01 13:28 ` [U-Boot] [PATCH 2/2] dts: imx8qxp-mek: Add PHY post reset delay Andrejs Cainikovs
0 siblings, 2 replies; 15+ messages in thread
From: Andrejs Cainikovs @ 2019-03-01 13:27 UTC (permalink / raw)
To: u-boot
This patchset introduces support for phy-reset-post-delay property,
which is then used by imx8qxp-mek to add 150ms post reset delay.
Without this delay PHY is not detected.
Andrejs Cainikovs (2):
net: dm: fec: Support phy-reset-post-delay property
dts: imx8qxp-mek: Add PHY post reset delay
arch/arm/dts/fsl-imx8qxp-mek.dts | 1 +
drivers/net/fec_mxc.c | 11 +++++++++++
drivers/net/fec_mxc.h | 1 +
3 files changed, 13 insertions(+)
---
2.11.0
^ permalink raw reply [flat|nested] 15+ messages in thread
* [U-Boot] [PATCH 1/2] net: dm: fec: Support phy-reset-post-delay property
2019-03-01 13:27 [U-Boot] [PATCH 0/2] Fix broken ethernet on imx8qxp-mek Andrejs Cainikovs
@ 2019-03-01 13:27 ` Andrejs Cainikovs
2019-03-01 13:57 ` Anatolij Gustschin
` (4 more replies)
2019-03-01 13:28 ` [U-Boot] [PATCH 2/2] dts: imx8qxp-mek: Add PHY post reset delay Andrejs Cainikovs
1 sibling, 5 replies; 15+ messages in thread
From: Andrejs Cainikovs @ 2019-03-01 13:27 UTC (permalink / raw)
To: u-boot
As per Linux kernel DT binding doc:
- phy-reset-post-delay : Post reset delay in milliseconds. If present then
a delay of phy-reset-post-delay milliseconds will be observed after the
phy-reset-gpios has been toggled. Can be omitted thus no delay is
observed. Delay is in range of 1ms to 1000ms. Other delays are invalid.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@netmodule.com>
---
drivers/net/fec_mxc.c | 11 +++++++++++
drivers/net/fec_mxc.h | 1 +
2 files changed, 12 insertions(+)
diff --git a/drivers/net/fec_mxc.c b/drivers/net/fec_mxc.c
index a14fe43a5b..7fc95fa767 100644
--- a/drivers/net/fec_mxc.c
+++ b/drivers/net/fec_mxc.c
@@ -1315,6 +1315,8 @@ static void fec_gpio_reset(struct fec_priv *priv)
dm_gpio_set_value(&priv->phy_reset_gpio, 1);
mdelay(priv->reset_delay);
dm_gpio_set_value(&priv->phy_reset_gpio, 0);
+ if (priv->reset_post_delay)
+ mdelay(priv->reset_post_delay);
}
}
#endif
@@ -1474,6 +1476,15 @@ static int fecmxc_ofdata_to_platdata(struct udevice *dev)
/* property value wrong, use default value */
priv->reset_delay = 1;
}
+
+ priv->reset_post_delay = dev_read_u32_default(dev,
+ "phy-reset-post-delay",
+ 0);
+ if (priv->reset_post_delay > 1000) {
+ printf("FEC MXC: phy reset post delay should be <= 1000ms\n");
+ /* property value wrong, use default value */
+ priv->reset_post_delay = 0;
+ }
#endif
return 0;
diff --git a/drivers/net/fec_mxc.h b/drivers/net/fec_mxc.h
index e9a661f0a1..e5f2dd75c5 100644
--- a/drivers/net/fec_mxc.h
+++ b/drivers/net/fec_mxc.h
@@ -258,6 +258,7 @@ struct fec_priv {
#ifdef CONFIG_DM_GPIO
struct gpio_desc phy_reset_gpio;
uint32_t reset_delay;
+ uint32_t reset_post_delay;
#endif
#ifdef CONFIG_DM_ETH
u32 interface;
--
2.11.0
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [U-Boot] [PATCH 2/2] dts: imx8qxp-mek: Add PHY post reset delay
2019-03-01 13:27 [U-Boot] [PATCH 0/2] Fix broken ethernet on imx8qxp-mek Andrejs Cainikovs
2019-03-01 13:27 ` [U-Boot] [PATCH 1/2] net: dm: fec: Support phy-reset-post-delay property Andrejs Cainikovs
@ 2019-03-01 13:28 ` Andrejs Cainikovs
2019-03-01 13:58 ` Anatolij Gustschin
` (3 more replies)
1 sibling, 4 replies; 15+ messages in thread
From: Andrejs Cainikovs @ 2019-03-01 13:28 UTC (permalink / raw)
To: u-boot
PHY cannot be detected unless we wait about 150 ms.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@netmodule.com>
---
arch/arm/dts/fsl-imx8qxp-mek.dts | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm/dts/fsl-imx8qxp-mek.dts b/arch/arm/dts/fsl-imx8qxp-mek.dts
index 41f7ec1763..4f35fbe31d 100644
--- a/arch/arm/dts/fsl-imx8qxp-mek.dts
+++ b/arch/arm/dts/fsl-imx8qxp-mek.dts
@@ -224,6 +224,7 @@
status = "okay";
phy-reset-gpios = <&pca9557_a 4 GPIO_ACTIVE_LOW>;
phy-reset-duration = <10>;
+ phy-reset-post-delay = <150>;
mdio {
#address-cells = <1>;
--
2.11.0
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [U-Boot] [PATCH 1/2] net: dm: fec: Support phy-reset-post-delay property
2019-03-01 13:27 ` [U-Boot] [PATCH 1/2] net: dm: fec: Support phy-reset-post-delay property Andrejs Cainikovs
@ 2019-03-01 13:57 ` Anatolij Gustschin
2019-03-01 14:07 ` Stefano Babic
` (3 subsequent siblings)
4 siblings, 0 replies; 15+ messages in thread
From: Anatolij Gustschin @ 2019-03-01 13:57 UTC (permalink / raw)
To: u-boot
On Fri, 1 Mar 2019 13:27:59 +0000
Andrejs Cainikovs Andrejs.Cainikovs at netmodule.com wrote:
> As per Linux kernel DT binding doc:
> - phy-reset-post-delay : Post reset delay in milliseconds. If present then
> a delay of phy-reset-post-delay milliseconds will be observed after the
> phy-reset-gpios has been toggled. Can be omitted thus no delay is
> observed. Delay is in range of 1ms to 1000ms. Other delays are invalid.
>
> Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@netmodule.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
--
Anatolij
^ permalink raw reply [flat|nested] 15+ messages in thread
* [U-Boot] [PATCH 2/2] dts: imx8qxp-mek: Add PHY post reset delay
2019-03-01 13:28 ` [U-Boot] [PATCH 2/2] dts: imx8qxp-mek: Add PHY post reset delay Andrejs Cainikovs
@ 2019-03-01 13:58 ` Anatolij Gustschin
2019-03-01 14:07 ` Stefano Babic
` (2 subsequent siblings)
3 siblings, 0 replies; 15+ messages in thread
From: Anatolij Gustschin @ 2019-03-01 13:58 UTC (permalink / raw)
To: u-boot
On Fri, 1 Mar 2019 13:28:00 +0000
Andrejs Cainikovs Andrejs.Cainikovs at netmodule.com wrote:
> PHY cannot be detected unless we wait about 150 ms.
>
> Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@netmodule.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
--
Anatolij
^ permalink raw reply [flat|nested] 15+ messages in thread
* [U-Boot] [PATCH 1/2] net: dm: fec: Support phy-reset-post-delay property
2019-03-01 13:27 ` [U-Boot] [PATCH 1/2] net: dm: fec: Support phy-reset-post-delay property Andrejs Cainikovs
2019-03-01 13:57 ` Anatolij Gustschin
@ 2019-03-01 14:07 ` Stefano Babic
2019-03-01 18:49 ` Joe Hershberger
` (2 subsequent siblings)
4 siblings, 0 replies; 15+ messages in thread
From: Stefano Babic @ 2019-03-01 14:07 UTC (permalink / raw)
To: u-boot
On 01/03/19 14:27, Andrejs Cainikovs wrote:
> As per Linux kernel DT binding doc:
> - phy-reset-post-delay : Post reset delay in milliseconds. If present then
> a delay of phy-reset-post-delay milliseconds will be observed after the
> phy-reset-gpios has been toggled. Can be omitted thus no delay is
> observed. Delay is in range of 1ms to 1000ms. Other delays are invalid.
>
> Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@netmodule.com>
> ---
> drivers/net/fec_mxc.c | 11 +++++++++++
> drivers/net/fec_mxc.h | 1 +
> 2 files changed, 12 insertions(+)
>
> diff --git a/drivers/net/fec_mxc.c b/drivers/net/fec_mxc.c
> index a14fe43a5b..7fc95fa767 100644
> --- a/drivers/net/fec_mxc.c
> +++ b/drivers/net/fec_mxc.c
> @@ -1315,6 +1315,8 @@ static void fec_gpio_reset(struct fec_priv *priv)
> dm_gpio_set_value(&priv->phy_reset_gpio, 1);
> mdelay(priv->reset_delay);
> dm_gpio_set_value(&priv->phy_reset_gpio, 0);
> + if (priv->reset_post_delay)
> + mdelay(priv->reset_post_delay);
> }
> }
> #endif
> @@ -1474,6 +1476,15 @@ static int fecmxc_ofdata_to_platdata(struct udevice *dev)
> /* property value wrong, use default value */
> priv->reset_delay = 1;
> }
> +
> + priv->reset_post_delay = dev_read_u32_default(dev,
> + "phy-reset-post-delay",
> + 0);
> + if (priv->reset_post_delay > 1000) {
> + printf("FEC MXC: phy reset post delay should be <= 1000ms\n");
> + /* property value wrong, use default value */
> + priv->reset_post_delay = 0;
> + }
> #endif
>
> return 0;
> diff --git a/drivers/net/fec_mxc.h b/drivers/net/fec_mxc.h
> index e9a661f0a1..e5f2dd75c5 100644
> --- a/drivers/net/fec_mxc.h
> +++ b/drivers/net/fec_mxc.h
> @@ -258,6 +258,7 @@ struct fec_priv {
> #ifdef CONFIG_DM_GPIO
> struct gpio_desc phy_reset_gpio;
> uint32_t reset_delay;
> + uint32_t reset_post_delay;
> #endif
> #ifdef CONFIG_DM_ETH
> u32 interface;
>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 15+ messages in thread
* [U-Boot] [PATCH 2/2] dts: imx8qxp-mek: Add PHY post reset delay
2019-03-01 13:28 ` [U-Boot] [PATCH 2/2] dts: imx8qxp-mek: Add PHY post reset delay Andrejs Cainikovs
2019-03-01 13:58 ` Anatolij Gustschin
@ 2019-03-01 14:07 ` Stefano Babic
2019-03-01 18:49 ` Joe Hershberger
2019-03-05 18:05 ` [U-Boot] " Joe Hershberger
3 siblings, 0 replies; 15+ messages in thread
From: Stefano Babic @ 2019-03-01 14:07 UTC (permalink / raw)
To: u-boot
On 01/03/19 14:28, Andrejs Cainikovs wrote:
> PHY cannot be detected unless we wait about 150 ms.
>
> Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@netmodule.com>
> ---
> arch/arm/dts/fsl-imx8qxp-mek.dts | 1 +
> 1 file changed, 1 insertion(+)
>
> diff --git a/arch/arm/dts/fsl-imx8qxp-mek.dts b/arch/arm/dts/fsl-imx8qxp-mek.dts
> index 41f7ec1763..4f35fbe31d 100644
> --- a/arch/arm/dts/fsl-imx8qxp-mek.dts
> +++ b/arch/arm/dts/fsl-imx8qxp-mek.dts
> @@ -224,6 +224,7 @@
> status = "okay";
> phy-reset-gpios = <&pca9557_a 4 GPIO_ACTIVE_LOW>;
> phy-reset-duration = <10>;
> + phy-reset-post-delay = <150>;
>
> mdio {
> #address-cells = <1>;
>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 15+ messages in thread
* [U-Boot] [PATCH 1/2] net: dm: fec: Support phy-reset-post-delay property
2019-03-01 13:27 ` [U-Boot] [PATCH 1/2] net: dm: fec: Support phy-reset-post-delay property Andrejs Cainikovs
2019-03-01 13:57 ` Anatolij Gustschin
2019-03-01 14:07 ` Stefano Babic
@ 2019-03-01 18:49 ` Joe Hershberger
2019-03-03 22:18 ` Lukasz Majewski
2019-03-05 18:05 ` [U-Boot] " Joe Hershberger
4 siblings, 0 replies; 15+ messages in thread
From: Joe Hershberger @ 2019-03-01 18:49 UTC (permalink / raw)
To: u-boot
On Fri, Mar 1, 2019 at 7:28 AM Andrejs Cainikovs
<Andrejs.Cainikovs@netmodule.com> wrote:
>
> As per Linux kernel DT binding doc:
> - phy-reset-post-delay : Post reset delay in milliseconds. If present then
> a delay of phy-reset-post-delay milliseconds will be observed after the
> phy-reset-gpios has been toggled. Can be omitted thus no delay is
> observed. Delay is in range of 1ms to 1000ms. Other delays are invalid.
>
> Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@netmodule.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
^ permalink raw reply [flat|nested] 15+ messages in thread
* [U-Boot] [PATCH 2/2] dts: imx8qxp-mek: Add PHY post reset delay
2019-03-01 13:28 ` [U-Boot] [PATCH 2/2] dts: imx8qxp-mek: Add PHY post reset delay Andrejs Cainikovs
2019-03-01 13:58 ` Anatolij Gustschin
2019-03-01 14:07 ` Stefano Babic
@ 2019-03-01 18:49 ` Joe Hershberger
2019-03-05 18:05 ` [U-Boot] " Joe Hershberger
3 siblings, 0 replies; 15+ messages in thread
From: Joe Hershberger @ 2019-03-01 18:49 UTC (permalink / raw)
To: u-boot
On Fri, Mar 1, 2019 at 7:28 AM Andrejs Cainikovs
<Andrejs.Cainikovs@netmodule.com> wrote:
>
> PHY cannot be detected unless we wait about 150 ms.
>
> Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@netmodule.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
^ permalink raw reply [flat|nested] 15+ messages in thread
* [U-Boot] [PATCH 1/2] net: dm: fec: Support phy-reset-post-delay property
2019-03-01 13:27 ` [U-Boot] [PATCH 1/2] net: dm: fec: Support phy-reset-post-delay property Andrejs Cainikovs
` (2 preceding siblings ...)
2019-03-01 18:49 ` Joe Hershberger
@ 2019-03-03 22:18 ` Lukasz Majewski
2019-03-05 18:05 ` [U-Boot] " Joe Hershberger
4 siblings, 0 replies; 15+ messages in thread
From: Lukasz Majewski @ 2019-03-03 22:18 UTC (permalink / raw)
To: u-boot
Hi Andrejs,
> As per Linux kernel DT binding doc:
> - phy-reset-post-delay : Post reset delay in milliseconds. If present
> then a delay of phy-reset-post-delay milliseconds will be observed
> after the phy-reset-gpios has been toggled. Can be omitted thus no
> delay is observed. Delay is in range of 1ms to 1000ms. Other delays
> are invalid.
>
> Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@netmodule.com>
> ---
> drivers/net/fec_mxc.c | 11 +++++++++++
> drivers/net/fec_mxc.h | 1 +
> 2 files changed, 12 insertions(+)
>
> diff --git a/drivers/net/fec_mxc.c b/drivers/net/fec_mxc.c
> index a14fe43a5b..7fc95fa767 100644
> --- a/drivers/net/fec_mxc.c
> +++ b/drivers/net/fec_mxc.c
> @@ -1315,6 +1315,8 @@ static void fec_gpio_reset(struct fec_priv
> *priv) dm_gpio_set_value(&priv->phy_reset_gpio, 1);
> mdelay(priv->reset_delay);
> dm_gpio_set_value(&priv->phy_reset_gpio, 0);
> + if (priv->reset_post_delay)
> + mdelay(priv->reset_post_delay);
> }
> }
> #endif
> @@ -1474,6 +1476,15 @@ static int fecmxc_ofdata_to_platdata(struct
> udevice *dev) /* property value wrong, use default value */
> priv->reset_delay = 1;
> }
> +
> + priv->reset_post_delay = dev_read_u32_default(dev,
> +
> "phy-reset-post-delay",
> + 0);
> + if (priv->reset_post_delay > 1000) {
> + printf("FEC MXC: phy reset post delay should be <=
> 1000ms\n");
> + /* property value wrong, use default value */
> + priv->reset_post_delay = 0;
> + }
> #endif
>
> return 0;
> diff --git a/drivers/net/fec_mxc.h b/drivers/net/fec_mxc.h
> index e9a661f0a1..e5f2dd75c5 100644
> --- a/drivers/net/fec_mxc.h
> +++ b/drivers/net/fec_mxc.h
> @@ -258,6 +258,7 @@ struct fec_priv {
> #ifdef CONFIG_DM_GPIO
> struct gpio_desc phy_reset_gpio;
> uint32_t reset_delay;
> + uint32_t reset_post_delay;
> #endif
> #ifdef CONFIG_DM_ETH
> u32 interface;
Acked-by: Lukasz Majewski <lukma@denx.de>
(as I had similar patch somewhere .... to fix this issue on IMX6Q).
Best regards,
Lukasz Majewski
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma at denx.de
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 488 bytes
Desc: OpenPGP digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190303/228f3ec7/attachment.sig>
^ permalink raw reply [flat|nested] 15+ messages in thread
* [U-Boot] net: dm: fec: Support phy-reset-post-delay property
2019-03-01 13:27 ` [U-Boot] [PATCH 1/2] net: dm: fec: Support phy-reset-post-delay property Andrejs Cainikovs
` (3 preceding siblings ...)
2019-03-03 22:18 ` Lukasz Majewski
@ 2019-03-05 18:05 ` Joe Hershberger
2019-03-12 9:10 ` Anatolij Gustschin
4 siblings, 1 reply; 15+ messages in thread
From: Joe Hershberger @ 2019-03-05 18:05 UTC (permalink / raw)
To: u-boot
Hi Andrejs,
https://patchwork.ozlabs.org/patch/1050177/ was applied to http://git.denx.de/?p=u-boot/u-boot-net.git
Thanks!
-Joe
^ permalink raw reply [flat|nested] 15+ messages in thread
* [U-Boot] dts: imx8qxp-mek: Add PHY post reset delay
2019-03-01 13:28 ` [U-Boot] [PATCH 2/2] dts: imx8qxp-mek: Add PHY post reset delay Andrejs Cainikovs
` (2 preceding siblings ...)
2019-03-01 18:49 ` Joe Hershberger
@ 2019-03-05 18:05 ` Joe Hershberger
2019-03-12 9:13 ` Anatolij Gustschin
3 siblings, 1 reply; 15+ messages in thread
From: Joe Hershberger @ 2019-03-05 18:05 UTC (permalink / raw)
To: u-boot
Hi Andrejs,
https://patchwork.ozlabs.org/patch/1050178/ was applied to http://git.denx.de/?p=u-boot/u-boot-net.git
Thanks!
-Joe
^ permalink raw reply [flat|nested] 15+ messages in thread
* [U-Boot] net: dm: fec: Support phy-reset-post-delay property
2019-03-05 18:05 ` [U-Boot] " Joe Hershberger
@ 2019-03-12 9:10 ` Anatolij Gustschin
2019-03-12 17:22 ` Joe Hershberger
0 siblings, 1 reply; 15+ messages in thread
From: Anatolij Gustschin @ 2019-03-12 9:10 UTC (permalink / raw)
To: u-boot
Hi Joe,
On Tue, 5 Mar 2019 12:05:38 -0600
Joe Hershberger joe.hershberger at ni.com wrote:
> Hi Andrejs,
>
> https://patchwork.ozlabs.org/patch/1050177/ was applied to http://git.denx.de/?p=u-boot/u-boot-net.git
This patch is not in mainline tree yet, but it is marked as accepted
on patchwork. Could you please check? This is part of a bug-fix for
broken ethernet on the board and should go into v2019.04 release.
Thanks,
Anatolij
^ permalink raw reply [flat|nested] 15+ messages in thread
* [U-Boot] dts: imx8qxp-mek: Add PHY post reset delay
2019-03-05 18:05 ` [U-Boot] " Joe Hershberger
@ 2019-03-12 9:13 ` Anatolij Gustschin
0 siblings, 0 replies; 15+ messages in thread
From: Anatolij Gustschin @ 2019-03-12 9:13 UTC (permalink / raw)
To: u-boot
Hi Joe,
On Tue, 5 Mar 2019 12:05:42 -0600
Joe Hershberger joe.hershberger at ni.com wrote:
> Hi Andrejs,
>
> https://patchwork.ozlabs.org/patch/1050178/ was applied to http://git.denx.de/?p=u-boot/u-boot-net.git
This patch is marked as accepted on patchwork, but it is not in mainline
tree yet. It should go into v2019.04 release, too. Could you please check?
Thanks,
Anatolij
^ permalink raw reply [flat|nested] 15+ messages in thread
* [U-Boot] net: dm: fec: Support phy-reset-post-delay property
2019-03-12 9:10 ` Anatolij Gustschin
@ 2019-03-12 17:22 ` Joe Hershberger
0 siblings, 0 replies; 15+ messages in thread
From: Joe Hershberger @ 2019-03-12 17:22 UTC (permalink / raw)
To: u-boot
Hi Anatolij,
On Tue, Mar 12, 2019 at 4:10 AM Anatolij Gustschin <agust@denx.de> wrote:
>
> Hi Joe,
>
> On Tue, 5 Mar 2019 12:05:38 -0600
> Joe Hershberger joe.hershberger at ni.com wrote:
>
> > Hi Andrejs,
> >
> > https://patchwork.ozlabs.org/patch/1050177/ was applied to http://git.denx.de/?p=u-boot/u-boot-net.git
>
> This patch is not in mainline tree yet, but it is marked as accepted
> on patchwork. Could you please check? This is part of a bug-fix for
> broken ethernet on the board and should go into v2019.04 release.
Yes, it should go into this release. Hopefully Tom will pull it in shortly.
Thanks,
-Joe
> Thanks,
> Anatolij
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> https://lists.denx.de/listinfo/u-boot
^ permalink raw reply [flat|nested] 15+ messages in thread
end of thread, other threads:[~2019-03-12 17:22 UTC | newest]
Thread overview: 15+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-03-01 13:27 [U-Boot] [PATCH 0/2] Fix broken ethernet on imx8qxp-mek Andrejs Cainikovs
2019-03-01 13:27 ` [U-Boot] [PATCH 1/2] net: dm: fec: Support phy-reset-post-delay property Andrejs Cainikovs
2019-03-01 13:57 ` Anatolij Gustschin
2019-03-01 14:07 ` Stefano Babic
2019-03-01 18:49 ` Joe Hershberger
2019-03-03 22:18 ` Lukasz Majewski
2019-03-05 18:05 ` [U-Boot] " Joe Hershberger
2019-03-12 9:10 ` Anatolij Gustschin
2019-03-12 17:22 ` Joe Hershberger
2019-03-01 13:28 ` [U-Boot] [PATCH 2/2] dts: imx8qxp-mek: Add PHY post reset delay Andrejs Cainikovs
2019-03-01 13:58 ` Anatolij Gustschin
2019-03-01 14:07 ` Stefano Babic
2019-03-01 18:49 ` Joe Hershberger
2019-03-05 18:05 ` [U-Boot] " Joe Hershberger
2019-03-12 9:13 ` Anatolij Gustschin
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.