* [PATCH v5 0/6] dma: Add Xilinx ZynqMP DPDMA driver
@ 2020-05-28 2:52 Laurent Pinchart
2020-05-28 2:52 ` [PATCH v5 1/6] dt: bindings: dma: xilinx: dpdma: DT bindings for Xilinx DPDMA Laurent Pinchart
` (6 more replies)
0 siblings, 7 replies; 18+ messages in thread
From: Laurent Pinchart @ 2020-05-28 2:52 UTC (permalink / raw)
To: dmaengine
Cc: Michal Simek, Hyun Kwon, Tejas Upadhyay, Satish Kumar Nagireddy,
Vinod Koul, Peter Ujfalusi
Hello,
This patch series adds a new driver for the DPDMA engine found in the
Xilinx ZynqMP.
The previous version can be found at [1]. All review comments have been
taken into account. The only change is the addition of the
DMA_PREP_LOAD_EOT transaction flag (and the corresponding DMA_LOAD_EOT
capability bit), as requested during the review of v4. Please see the
discussions from v4 for the rationale.
The driver has been successfully tested with the ZynqMP DisplayPort
subsystem DRM driver.
[1] https://lore.kernel.org/dmaengine/20200513165943.25120-1-laurent.pinchart@ideasonboard.com/
Hyun Kwon (1):
dmaengine: xilinx: dpdma: Add the Xilinx DisplayPort DMA engine driver
Laurent Pinchart (5):
dt: bindings: dma: xilinx: dpdma: DT bindings for Xilinx DPDMA
dmaengine: virt-dma: Use lockdep to check locking requirements
dmaengine: Add support for repeating transactions
dmaengine: xilinx: dpdma: Add debugfs support
arm64: dts: zynqmp: Add DPDMA node
.../dma/xilinx/xlnx,zynqmp-dpdma.yaml | 68 +
MAINTAINERS | 9 +
.../arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi | 4 +
arch/arm64/boot/dts/xilinx/zynqmp.dtsi | 10 +
drivers/dma/Kconfig | 10 +
drivers/dma/virt-dma.c | 2 +
drivers/dma/virt-dma.h | 10 +
drivers/dma/xilinx/Makefile | 1 +
drivers/dma/xilinx/xilinx_dpdma.c | 1782 +++++++++++++++++
include/dt-bindings/dma/xlnx-zynqmp-dpdma.h | 16 +
include/linux/dmaengine.h | 19 +
11 files changed, 1931 insertions(+)
create mode 100644 Documentation/devicetree/bindings/dma/xilinx/xlnx,zynqmp-dpdma.yaml
create mode 100644 drivers/dma/xilinx/xilinx_dpdma.c
create mode 100644 include/dt-bindings/dma/xlnx-zynqmp-dpdma.h
--
Regards,
Laurent Pinchart
^ permalink raw reply [flat|nested] 18+ messages in thread* [PATCH v5 1/6] dt: bindings: dma: xilinx: dpdma: DT bindings for Xilinx DPDMA 2020-05-28 2:52 [PATCH v5 0/6] dma: Add Xilinx ZynqMP DPDMA driver Laurent Pinchart @ 2020-05-28 2:52 ` Laurent Pinchart 2020-05-28 2:52 ` [PATCH v5 2/6] dmaengine: virt-dma: Use lockdep to check locking requirements Laurent Pinchart ` (5 subsequent siblings) 6 siblings, 0 replies; 18+ messages in thread From: Laurent Pinchart @ 2020-05-28 2:52 UTC (permalink / raw) To: dmaengine Cc: Michal Simek, Hyun Kwon, Tejas Upadhyay, Satish Kumar Nagireddy, Vinod Koul, Peter Ujfalusi The ZynqMP includes the DisplayPort subsystem with its own DMA engine called DPDMA. The DPDMA IP comes with 6 individual channels (4 for display, 2 for audio). This documentation describes DT bindings of DPDMA. Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Rob Herring <robh@kernel.org> --- Changes since v2: - Fix id URL - Fix path to dma-controller.yaml - Update license to GPL-2.0-only OR BSD-2-Clause Changes since v1: - Convert the DT bindings to YAML - Drop the DT child nodes --- .../dma/xilinx/xlnx,zynqmp-dpdma.yaml | 68 +++++++++++++++++++ MAINTAINERS | 8 +++ include/dt-bindings/dma/xlnx-zynqmp-dpdma.h | 16 +++++ 3 files changed, 92 insertions(+) create mode 100644 Documentation/devicetree/bindings/dma/xilinx/xlnx,zynqmp-dpdma.yaml create mode 100644 include/dt-bindings/dma/xlnx-zynqmp-dpdma.h diff --git a/Documentation/devicetree/bindings/dma/xilinx/xlnx,zynqmp-dpdma.yaml b/Documentation/devicetree/bindings/dma/xilinx/xlnx,zynqmp-dpdma.yaml new file mode 100644 index 000000000000..5de510f8c88c --- /dev/null +++ b/Documentation/devicetree/bindings/dma/xilinx/xlnx,zynqmp-dpdma.yaml @@ -0,0 +1,68 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/dma/xilinx/xlnx,zynqmp-dpdma.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Xilinx ZynqMP DisplayPort DMA Controller Device Tree Bindings + +description: | + These bindings describe the DMA engine included in the Xilinx ZynqMP + DisplayPort Subsystem. The DMA engine supports up to 6 DMA channels (3 + channels for a video stream, 1 channel for a graphics stream, and 2 channels + for an audio stream). + +maintainers: + - Laurent Pinchart <laurent.pinchart@ideasonboard.com> + +allOf: + - $ref: "../dma-controller.yaml#" + +properties: + "#dma-cells": + const: 1 + description: | + The cell is the DMA channel ID (see dt-bindings/dma/xlnx-zynqmp-dpdma.h + for a list of channel IDs). + + compatible: + const: xlnx,zynqmp-dpdma + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + description: The AXI clock + maxItems: 1 + + clock-names: + const: axi_clk + +required: + - "#dma-cells" + - compatible + - reg + - interrupts + - clocks + - clock-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + + dma: dma-controller@fd4c0000 { + compatible = "xlnx,zynqmp-dpdma"; + reg = <0x0 0xfd4c0000 0x0 0x1000>; + interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>; + interrupt-parent = <&gic>; + clocks = <&dpdma_clk>; + clock-names = "axi_clk"; + #dma-cells = <1>; + }; + +... diff --git a/MAINTAINERS b/MAINTAINERS index f437f42b73ad..97a7de450cb4 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -18588,6 +18588,14 @@ F: Documentation/devicetree/bindings/media/xilinx/ F: drivers/media/platform/xilinx/ F: include/uapi/linux/xilinx-v4l2-controls.h +XILINX ZYNQMP DPDMA DRIVER +M: Hyun Kwon <hyun.kwon@xilinx.com> +M: Laurent Pinchart <laurent.pinchart@ideasonboard.com> +L: dmaengine@vger.kernel.org +S: Supported +F: Documentation/devicetree/bindings/dma/xilinx/xlnx,zynqmp-dpdma.yaml +F: include/dt-bindings/dma/xlnx-zynqmp-dpdma.h + XILLYBUS DRIVER M: Eli Billauer <eli.billauer@gmail.com> L: linux-kernel@vger.kernel.org diff --git a/include/dt-bindings/dma/xlnx-zynqmp-dpdma.h b/include/dt-bindings/dma/xlnx-zynqmp-dpdma.h new file mode 100644 index 000000000000..3719cda5679d --- /dev/null +++ b/include/dt-bindings/dma/xlnx-zynqmp-dpdma.h @@ -0,0 +1,16 @@ +/* SPDX-License-Identifier: (GPL-2.0 OR MIT) */ +/* + * Copyright 2019 Laurent Pinchart <laurent.pinchart@ideasonboard.com> + */ + +#ifndef __DT_BINDINGS_DMA_XLNX_ZYNQMP_DPDMA_H__ +#define __DT_BINDINGS_DMA_XLNX_ZYNQMP_DPDMA_H__ + +#define ZYNQMP_DPDMA_VIDEO0 0 +#define ZYNQMP_DPDMA_VIDEO1 1 +#define ZYNQMP_DPDMA_VIDEO2 2 +#define ZYNQMP_DPDMA_GRAPHICS 3 +#define ZYNQMP_DPDMA_AUDIO0 4 +#define ZYNQMP_DPDMA_AUDIO1 5 + +#endif /* __DT_BINDINGS_DMA_XLNX_ZYNQMP_DPDMA_H__ */ -- Regards, Laurent Pinchart ^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH v5 2/6] dmaengine: virt-dma: Use lockdep to check locking requirements 2020-05-28 2:52 [PATCH v5 0/6] dma: Add Xilinx ZynqMP DPDMA driver Laurent Pinchart 2020-05-28 2:52 ` [PATCH v5 1/6] dt: bindings: dma: xilinx: dpdma: DT bindings for Xilinx DPDMA Laurent Pinchart @ 2020-05-28 2:52 ` Laurent Pinchart 2020-05-28 2:52 ` [PATCH v5 3/6] dmaengine: Add support for repeating transactions Laurent Pinchart ` (4 subsequent siblings) 6 siblings, 0 replies; 18+ messages in thread From: Laurent Pinchart @ 2020-05-28 2:52 UTC (permalink / raw) To: dmaengine Cc: Michal Simek, Hyun Kwon, Tejas Upadhyay, Satish Kumar Nagireddy, Vinod Koul, Peter Ujfalusi A few virt-dma functions are documented as requiring the vc.lock to be held by the caller. Check this with lockdep. The vchan_vdesc_fini() and vchan_find_desc() functions gain a lockdep check as well, because, even though they are not documented with this requirement (and not documented at all for the latter), they touch fields documented as protected by vc.lock. All callers have been manually inspected to verify they call the functions with the lock held. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> --- drivers/dma/virt-dma.c | 2 ++ drivers/dma/virt-dma.h | 10 ++++++++++ 2 files changed, 12 insertions(+) diff --git a/drivers/dma/virt-dma.c b/drivers/dma/virt-dma.c index 23e33a85f033..1cb36ab3d9c1 100644 --- a/drivers/dma/virt-dma.c +++ b/drivers/dma/virt-dma.c @@ -68,6 +68,8 @@ struct virt_dma_desc *vchan_find_desc(struct virt_dma_chan *vc, { struct virt_dma_desc *vd; + lockdep_assert_held(&vc->lock); + list_for_each_entry(vd, &vc->desc_issued, node) if (vd->tx.cookie == cookie) return vd; diff --git a/drivers/dma/virt-dma.h b/drivers/dma/virt-dma.h index e9f5250fbe4d..59d9eabc8b67 100644 --- a/drivers/dma/virt-dma.h +++ b/drivers/dma/virt-dma.h @@ -81,6 +81,8 @@ static inline struct dma_async_tx_descriptor *vchan_tx_prep(struct virt_dma_chan */ static inline bool vchan_issue_pending(struct virt_dma_chan *vc) { + lockdep_assert_held(&vc->lock); + list_splice_tail_init(&vc->desc_submitted, &vc->desc_issued); return !list_empty(&vc->desc_issued); } @@ -96,6 +98,8 @@ static inline void vchan_cookie_complete(struct virt_dma_desc *vd) struct virt_dma_chan *vc = to_virt_chan(vd->tx.chan); dma_cookie_t cookie; + lockdep_assert_held(&vc->lock); + cookie = vd->tx.cookie; dma_cookie_complete(&vd->tx); dev_vdbg(vc->chan.device->dev, "txd %p[%x]: marked complete\n", @@ -146,6 +150,8 @@ static inline void vchan_terminate_vdesc(struct virt_dma_desc *vd) { struct virt_dma_chan *vc = to_virt_chan(vd->tx.chan); + lockdep_assert_held(&vc->lock); + list_add_tail(&vd->node, &vc->desc_terminated); if (vc->cyclic == vd) @@ -160,6 +166,8 @@ static inline void vchan_terminate_vdesc(struct virt_dma_desc *vd) */ static inline struct virt_dma_desc *vchan_next_desc(struct virt_dma_chan *vc) { + lockdep_assert_held(&vc->lock); + return list_first_entry_or_null(&vc->desc_issued, struct virt_dma_desc, node); } @@ -177,6 +185,8 @@ static inline struct virt_dma_desc *vchan_next_desc(struct virt_dma_chan *vc) static inline void vchan_get_all_descriptors(struct virt_dma_chan *vc, struct list_head *head) { + lockdep_assert_held(&vc->lock); + list_splice_tail_init(&vc->desc_allocated, head); list_splice_tail_init(&vc->desc_submitted, head); list_splice_tail_init(&vc->desc_issued, head); -- Regards, Laurent Pinchart ^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH v5 3/6] dmaengine: Add support for repeating transactions 2020-05-28 2:52 [PATCH v5 0/6] dma: Add Xilinx ZynqMP DPDMA driver Laurent Pinchart 2020-05-28 2:52 ` [PATCH v5 1/6] dt: bindings: dma: xilinx: dpdma: DT bindings for Xilinx DPDMA Laurent Pinchart 2020-05-28 2:52 ` [PATCH v5 2/6] dmaengine: virt-dma: Use lockdep to check locking requirements Laurent Pinchart @ 2020-05-28 2:52 ` Laurent Pinchart 2020-07-03 17:10 ` Vinod Koul 2020-05-28 2:52 ` [PATCH v5 4/6] dmaengine: xilinx: dpdma: Add the Xilinx DisplayPort DMA engine driver Laurent Pinchart ` (3 subsequent siblings) 6 siblings, 1 reply; 18+ messages in thread From: Laurent Pinchart @ 2020-05-28 2:52 UTC (permalink / raw) To: dmaengine Cc: Michal Simek, Hyun Kwon, Tejas Upadhyay, Satish Kumar Nagireddy, Vinod Koul, Peter Ujfalusi DMA engines used with displays perform 2D interleaved transfers to read framebuffers from memory and feed the data to the display engine. As the same framebuffer can be displayed for multiple frames, the DMA transactions need to be repeated until a new framebuffer replaces the current one. This feature is implemented natively by some DMA engines that have the ability to repeat transactions and switch to a new transaction at the end of a transfer without any race condition or frame loss. This patch implements support for this feature in the DMA engine API. A new DMA_PREP_REPEAT transaction flag allows DMA clients to instruct the DMA channel to repeat the transaction automatically until one or more new transactions are issued on the channel (or until all active DMA transfers are explicitly terminated with the dmaengine_terminate_*() functions). A new DMA_REPEAT transaction type is also added for DMA engine drivers to report their support of the DMA_PREP_REPEAT flag. A new DMA_PREP_LOAD_EOT transaction flag is also introduced (with a corresponding DMA_LOAD_EOT capability bit), as requested during the review of v4. The flag instructs the DMA channel that the transaction being queued should replace the active repeated transaction when the latter terminates (at End Of Transaction). Not setting the flag will result in the active repeated transaction to continue being repeated, and the new transaction being silently ignored. The DMA_PREP_REPEAT flag is currently supported for interleaved transactions only. Its usage can easily be extended to cover more transaction types simply by adding an appropriate check in the corresponding dmaengine_prep_*() function. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> --- Changes since v4: - Add DMA_LOAD_EOT and DMA_PREP_LOAD_EOT flags --- include/linux/dmaengine.h | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+) diff --git a/include/linux/dmaengine.h b/include/linux/dmaengine.h index 21065c04c4ac..8e3769c2b841 100644 --- a/include/linux/dmaengine.h +++ b/include/linux/dmaengine.h @@ -61,6 +61,8 @@ enum dma_transaction_type { DMA_SLAVE, DMA_CYCLIC, DMA_INTERLEAVE, + DMA_REPEAT, + DMA_LOAD_EOT, /* last transaction type for creation of the capabilities mask */ DMA_TX_TYPE_END, }; @@ -176,6 +178,18 @@ struct dma_interleaved_template { * @DMA_PREP_CMD: tell the driver that the data passed to DMA API is command * data and the descriptor should be in different format from normal * data descriptors. + * @DMA_PREP_REPEAT: tell the driver that the transaction shall be automatically + * repeated when it ends if no other transaction has been issued on the same + * channel. If other transactions have been issued, this transaction completes + * normally. This flag is only applicable to interleaved transactions and is + * ignored for all other transaction types. + * @DMA_PREP_LOAD_EOT: tell the driver that the transaction shall replaced any + * active repeated (as indicated by DMA_PREP_REPEAT) transaction when the + * repeated transaction terminate. Not setting this flag when the previously + * queued transaction is marked with DMA_PREP_REPEAT will cause the new + * transaction to never be processed and stay in the issued queue forever. + * The flag is ignored if the previous transaction is not a repeated + * transaction. */ enum dma_ctrl_flags { DMA_PREP_INTERRUPT = (1 << 0), @@ -186,6 +200,8 @@ enum dma_ctrl_flags { DMA_PREP_FENCE = (1 << 5), DMA_CTRL_REUSE = (1 << 6), DMA_PREP_CMD = (1 << 7), + DMA_PREP_REPEAT = (1 << 8), + DMA_PREP_LOAD_EOT = (1 << 9), }; /** @@ -980,6 +996,9 @@ static inline struct dma_async_tx_descriptor *dmaengine_prep_interleaved_dma( { if (!chan || !chan->device || !chan->device->device_prep_interleaved_dma) return NULL; + if (flags & DMA_PREP_REPEAT && + !test_bit(DMA_REPEAT, chan->device->cap_mask.bits)) + return NULL; return chan->device->device_prep_interleaved_dma(chan, xt, flags); } -- Regards, Laurent Pinchart ^ permalink raw reply related [flat|nested] 18+ messages in thread
* Re: [PATCH v5 3/6] dmaengine: Add support for repeating transactions 2020-05-28 2:52 ` [PATCH v5 3/6] dmaengine: Add support for repeating transactions Laurent Pinchart @ 2020-07-03 17:10 ` Vinod Koul 2020-07-03 17:22 ` Laurent Pinchart 0 siblings, 1 reply; 18+ messages in thread From: Vinod Koul @ 2020-07-03 17:10 UTC (permalink / raw) To: Laurent Pinchart Cc: dmaengine, Michal Simek, Hyun Kwon, Tejas Upadhyay, Satish Kumar Nagireddy, Peter Ujfalusi Hi Laurent, On 28-05-20, 05:52, Laurent Pinchart wrote: > @@ -176,6 +178,18 @@ struct dma_interleaved_template { > * @DMA_PREP_CMD: tell the driver that the data passed to DMA API is command > * data and the descriptor should be in different format from normal > * data descriptors. > + * @DMA_PREP_REPEAT: tell the driver that the transaction shall be automatically > + * repeated when it ends if no other transaction has been issued on the same > + * channel. If other transactions have been issued, this transaction completes > + * normally. This flag is only applicable to interleaved transactions and is > + * ignored for all other transaction types. 1. Let us not restrict this to only interleave (hint we can in future replace cyclic API) 2. DMA_PREP_REPEAT telling the transaction shall be automatically repeated is okay. No issues with that > + * @DMA_PREP_LOAD_EOT: tell the driver that the transaction shall replaced any s/replaced/replace > + * active repeated (as indicated by DMA_PREP_REPEAT) transaction when the > + * repeated transaction terminate. Not setting this flag when the previously > + * queued transaction is marked with DMA_PREP_REPEAT will cause the new > + * transaction to never be processed and stay in the issued queue forever. > + * The flag is ignored if the previous transaction is not a repeated > + * transaction. I am happy with this bit, I think we dont need to specify something like DMA_PREP_LOAD_NEXT given the explanation here, so adding DMA_PREP_LOAD_EOT would mean that. Can we add a corresponding EOB as well to complete this -- ~Vinod ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH v5 3/6] dmaengine: Add support for repeating transactions 2020-07-03 17:10 ` Vinod Koul @ 2020-07-03 17:22 ` Laurent Pinchart 2020-07-03 17:37 ` Vinod Koul 0 siblings, 1 reply; 18+ messages in thread From: Laurent Pinchart @ 2020-07-03 17:22 UTC (permalink / raw) To: Vinod Koul Cc: dmaengine, Michal Simek, Hyun Kwon, Tejas Upadhyay, Satish Kumar Nagireddy, Peter Ujfalusi Hi Vinod, On Fri, Jul 03, 2020 at 10:40:39PM +0530, Vinod Koul wrote: > Hi Laurent, > > On 28-05-20, 05:52, Laurent Pinchart wrote: > > > @@ -176,6 +178,18 @@ struct dma_interleaved_template { > > * @DMA_PREP_CMD: tell the driver that the data passed to DMA API is command > > * data and the descriptor should be in different format from normal > > * data descriptors. > > + * @DMA_PREP_REPEAT: tell the driver that the transaction shall be automatically > > + * repeated when it ends if no other transaction has been issued on the same > > + * channel. If other transactions have been issued, this transaction completes > > + * normally. This flag is only applicable to interleaved transactions and is > > + * ignored for all other transaction types. > > 1. Let us not restrict this to only interleave (hint we can in future > replace cyclic API) Peter wanted to already implement support for DMA_PREP_REPEAT in other transaction types, and you replied that you would prefer not enabling APIs without users, waiting for the first user of DMA_PREP_REPEAT with a non-interleaved transaction to do so. Your comment here seems to contract that. Which way do you want to go ? > 2. DMA_PREP_REPEAT telling the transaction shall be automatically > repeated is okay. No issues with that > > > + * @DMA_PREP_LOAD_EOT: tell the driver that the transaction shall replaced any > > s/replaced/replace > > > + * active repeated (as indicated by DMA_PREP_REPEAT) transaction when the > > + * repeated transaction terminate. Not setting this flag when the previously > > + * queued transaction is marked with DMA_PREP_REPEAT will cause the new > > + * transaction to never be processed and stay in the issued queue forever. > > + * The flag is ignored if the previous transaction is not a repeated > > + * transaction. > > I am happy with this bit, I think we dont need to specify something like > DMA_PREP_LOAD_NEXT given the explanation here, so adding > DMA_PREP_LOAD_EOT would mean that. Just to clarify, does that mean I don't need to add a DMA_PREP_LOAD_NEXT flag in the API ? > Can we add a corresponding EOB as well to complete this What's EOB ? -- Regards, Laurent Pinchart ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH v5 3/6] dmaengine: Add support for repeating transactions 2020-07-03 17:22 ` Laurent Pinchart @ 2020-07-03 17:37 ` Vinod Koul 2020-07-03 17:47 ` Laurent Pinchart 0 siblings, 1 reply; 18+ messages in thread From: Vinod Koul @ 2020-07-03 17:37 UTC (permalink / raw) To: Laurent Pinchart Cc: dmaengine, Michal Simek, Hyun Kwon, Tejas Upadhyay, Satish Kumar Nagireddy, Peter Ujfalusi Hi Laurent, On 03-07-20, 20:22, Laurent Pinchart wrote: > On Fri, Jul 03, 2020 at 10:40:39PM +0530, Vinod Koul wrote: > > On 28-05-20, 05:52, Laurent Pinchart wrote: > > > > > @@ -176,6 +178,18 @@ struct dma_interleaved_template { > > > * @DMA_PREP_CMD: tell the driver that the data passed to DMA API is command > > > * data and the descriptor should be in different format from normal > > > * data descriptors. > > > + * @DMA_PREP_REPEAT: tell the driver that the transaction shall be automatically > > > + * repeated when it ends if no other transaction has been issued on the same > > > + * channel. If other transactions have been issued, this transaction completes > > > + * normally. This flag is only applicable to interleaved transactions and is > > > + * ignored for all other transaction types. > > > > 1. Let us not restrict this to only interleave (hint we can in future > > replace cyclic API) > > Peter wanted to already implement support for DMA_PREP_REPEAT in other > transaction types, and you replied that you would prefer not enabling > APIs without users, waiting for the first user of DMA_PREP_REPEAT with a > non-interleaved transaction to do so. Your comment here seems to > contract that. Which way do you want to go ? I would like to change the language of the explanation to not forbid other uses, but they would be enabled in txn when we have users.. > > 2. DMA_PREP_REPEAT telling the transaction shall be automatically > > repeated is okay. No issues with that > > > > > + * @DMA_PREP_LOAD_EOT: tell the driver that the transaction shall replaced any > > > > s/replaced/replace > > > > > + * active repeated (as indicated by DMA_PREP_REPEAT) transaction when the > > > + * repeated transaction terminate. Not setting this flag when the previously > > > + * queued transaction is marked with DMA_PREP_REPEAT will cause the new > > > + * transaction to never be processed and stay in the issued queue forever. > > > + * The flag is ignored if the previous transaction is not a repeated > > > + * transaction. > > > > I am happy with this bit, I think we dont need to specify something like > > DMA_PREP_LOAD_NEXT given the explanation here, so adding > > DMA_PREP_LOAD_EOT would mean that. > > Just to clarify, does that mean I don't need to add a DMA_PREP_LOAD_NEXT > flag in the API ? > > > Can we add a corresponding EOB as well to complete this > > What's EOB ? End of Burst, DMA would complete current burst and then terminate. I do understand it is not applicable for your case as your hw doesn't support it and would be unused but this is another case which would be useful so for completeness we should add this -- ~Vinod ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH v5 3/6] dmaengine: Add support for repeating transactions 2020-07-03 17:37 ` Vinod Koul @ 2020-07-03 17:47 ` Laurent Pinchart 2020-07-03 17:54 ` Vinod Koul 0 siblings, 1 reply; 18+ messages in thread From: Laurent Pinchart @ 2020-07-03 17:47 UTC (permalink / raw) To: Vinod Koul Cc: dmaengine, Michal Simek, Hyun Kwon, Tejas Upadhyay, Satish Kumar Nagireddy, Peter Ujfalusi Hi Vinod, On Fri, Jul 03, 2020 at 11:07:10PM +0530, Vinod Koul wrote: > On 03-07-20, 20:22, Laurent Pinchart wrote: > > On Fri, Jul 03, 2020 at 10:40:39PM +0530, Vinod Koul wrote: > > > On 28-05-20, 05:52, Laurent Pinchart wrote: > > > > > > > @@ -176,6 +178,18 @@ struct dma_interleaved_template { > > > > * @DMA_PREP_CMD: tell the driver that the data passed to DMA API is command > > > > * data and the descriptor should be in different format from normal > > > > * data descriptors. > > > > + * @DMA_PREP_REPEAT: tell the driver that the transaction shall be automatically > > > > + * repeated when it ends if no other transaction has been issued on the same > > > > + * channel. If other transactions have been issued, this transaction completes > > > > + * normally. This flag is only applicable to interleaved transactions and is > > > > + * ignored for all other transaction types. > > > > > > 1. Let us not restrict this to only interleave (hint we can in future > > > replace cyclic API) > > > > Peter wanted to already implement support for DMA_PREP_REPEAT in other > > transaction types, and you replied that you would prefer not enabling > > APIs without users, waiting for the first user of DMA_PREP_REPEAT with a > > non-interleaved transaction to do so. Your comment here seems to > > contract that. Which way do you want to go ? > > I would like to change the language of the explanation to not forbid > other uses, but they would be enabled in txn when we have users.. The documentation isn't set in stone, it can be updated when support for DMA_PREP_REPEAT will be enabled in other transaction types. I think it's better to have the documentation and code match, the documentation should describe the current implementation. I can add an additional sentence at the end of the paragraph to state "Support for this flag in other transaction types may be added in the future if the need arises." if that makes you feel better about it. > > > 2. DMA_PREP_REPEAT telling the transaction shall be automatically > > > repeated is okay. No issues with that > > > > > > > + * @DMA_PREP_LOAD_EOT: tell the driver that the transaction shall replaced any > > > > > > s/replaced/replace > > > > > > > + * active repeated (as indicated by DMA_PREP_REPEAT) transaction when the > > > > + * repeated transaction terminate. Not setting this flag when the previously > > > > + * queued transaction is marked with DMA_PREP_REPEAT will cause the new > > > > + * transaction to never be processed and stay in the issued queue forever. > > > > + * The flag is ignored if the previous transaction is not a repeated > > > > + * transaction. > > > > > > I am happy with this bit, I think we dont need to specify something like > > > DMA_PREP_LOAD_NEXT given the explanation here, so adding > > > DMA_PREP_LOAD_EOT would mean that. > > > > Just to clarify, does that mean I don't need to add a DMA_PREP_LOAD_NEXT > > flag in the API ? > > > > > Can we add a corresponding EOB as well to complete this > > > > What's EOB ? > > End of Burst, DMA would complete current burst and then terminate. I do > understand it is not applicable for your case as your hw doesn't support > it and would be unused but this is another case which would be useful so > for completeness we should add this Why not add it when we'll have a user for it ? How can you otherwise guarantee that it's a correct API if there's not even a single user that we can test the design with ? -- Regards, Laurent Pinchart ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH v5 3/6] dmaengine: Add support for repeating transactions 2020-07-03 17:47 ` Laurent Pinchart @ 2020-07-03 17:54 ` Vinod Koul 2020-07-08 20:19 ` Laurent Pinchart 0 siblings, 1 reply; 18+ messages in thread From: Vinod Koul @ 2020-07-03 17:54 UTC (permalink / raw) To: Laurent Pinchart Cc: dmaengine, Michal Simek, Hyun Kwon, Tejas Upadhyay, Satish Kumar Nagireddy, Peter Ujfalusi HI Laurent, On 03-07-20, 20:47, Laurent Pinchart wrote: > On Fri, Jul 03, 2020 at 11:07:10PM +0530, Vinod Koul wrote: > > On 03-07-20, 20:22, Laurent Pinchart wrote: > > > On Fri, Jul 03, 2020 at 10:40:39PM +0530, Vinod Koul wrote: > > > > On 28-05-20, 05:52, Laurent Pinchart wrote: > > > > > > > > > @@ -176,6 +178,18 @@ struct dma_interleaved_template { > > > > > * @DMA_PREP_CMD: tell the driver that the data passed to DMA API is command > > > > > * data and the descriptor should be in different format from normal > > > > > * data descriptors. > > > > > + * @DMA_PREP_REPEAT: tell the driver that the transaction shall be automatically > > > > > + * repeated when it ends if no other transaction has been issued on the same > > > > > + * channel. If other transactions have been issued, this transaction completes > > > > > + * normally. This flag is only applicable to interleaved transactions and is > > > > > + * ignored for all other transaction types. > > > > > > > > 1. Let us not restrict this to only interleave (hint we can in future > > > > replace cyclic API) > > > > > > Peter wanted to already implement support for DMA_PREP_REPEAT in other > > > transaction types, and you replied that you would prefer not enabling > > > APIs without users, waiting for the first user of DMA_PREP_REPEAT with a > > > non-interleaved transaction to do so. Your comment here seems to > > > contract that. Which way do you want to go ? > > > > I would like to change the language of the explanation to not forbid > > other uses, but they would be enabled in txn when we have users.. > > The documentation isn't set in stone, it can be updated when support for > DMA_PREP_REPEAT will be enabled in other transaction types. I think it's > better to have the documentation and code match, the documentation > should describe the current implementation. I can add an additional > sentence at the end of the paragraph to state "Support for this flag in > other transaction types may be added in the future if the need arises." > if that makes you feel better about it. Okay I will be okay with that caveat > > > > 2. DMA_PREP_REPEAT telling the transaction shall be automatically > > > > repeated is okay. No issues with that > > > > > > > > > + * @DMA_PREP_LOAD_EOT: tell the driver that the transaction shall replaced any > > > > > > > > s/replaced/replace > > > > > > > > > + * active repeated (as indicated by DMA_PREP_REPEAT) transaction when the > > > > > + * repeated transaction terminate. Not setting this flag when the previously > > > > > + * queued transaction is marked with DMA_PREP_REPEAT will cause the new > > > > > + * transaction to never be processed and stay in the issued queue forever. > > > > > + * The flag is ignored if the previous transaction is not a repeated > > > > > + * transaction. > > > > > > > > I am happy with this bit, I think we dont need to specify something like > > > > DMA_PREP_LOAD_NEXT given the explanation here, so adding > > > > DMA_PREP_LOAD_EOT would mean that. > > > > > > Just to clarify, does that mean I don't need to add a DMA_PREP_LOAD_NEXT > > > flag in the API ? > > > > > > > Can we add a corresponding EOB as well to complete this > > > > > > What's EOB ? > > > > End of Burst, DMA would complete current burst and then terminate. I do > > understand it is not applicable for your case as your hw doesn't support > > it and would be unused but this is another case which would be useful so > > for completeness we should add this > > Why not add it when we'll have a user for it ? How can you otherwise > guarantee that it's a correct API if there's not even a single user that > we can test the design with ? Okay lets not add but add a note that additional flags can be added when required like EOB Also can we add a note in Documentation about these flags and how they should be used for repeating transactions. Thanks -- ~Vinod ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH v5 3/6] dmaengine: Add support for repeating transactions 2020-07-03 17:54 ` Vinod Koul @ 2020-07-08 20:19 ` Laurent Pinchart 0 siblings, 0 replies; 18+ messages in thread From: Laurent Pinchart @ 2020-07-08 20:19 UTC (permalink / raw) To: Vinod Koul Cc: dmaengine, Michal Simek, Hyun Kwon, Tejas Upadhyay, Satish Kumar Nagireddy, Peter Ujfalusi Hi Vinod, On Fri, Jul 03, 2020 at 11:24:41PM +0530, Vinod Koul wrote: > On 03-07-20, 20:47, Laurent Pinchart wrote: > > On Fri, Jul 03, 2020 at 11:07:10PM +0530, Vinod Koul wrote: > >> On 03-07-20, 20:22, Laurent Pinchart wrote: > >>> On Fri, Jul 03, 2020 at 10:40:39PM +0530, Vinod Koul wrote: > >>>> On 28-05-20, 05:52, Laurent Pinchart wrote: > >>>> > >>>>> @@ -176,6 +178,18 @@ struct dma_interleaved_template { > >>>>> * @DMA_PREP_CMD: tell the driver that the data passed to DMA API is command > >>>>> * data and the descriptor should be in different format from normal > >>>>> * data descriptors. > >>>>> + * @DMA_PREP_REPEAT: tell the driver that the transaction shall be automatically > >>>>> + * repeated when it ends if no other transaction has been issued on the same > >>>>> + * channel. If other transactions have been issued, this transaction completes > >>>>> + * normally. This flag is only applicable to interleaved transactions and is > >>>>> + * ignored for all other transaction types. > >>>> > >>>> 1. Let us not restrict this to only interleave (hint we can in future > >>>> replace cyclic API) > >>> > >>> Peter wanted to already implement support for DMA_PREP_REPEAT in other > >>> transaction types, and you replied that you would prefer not enabling > >>> APIs without users, waiting for the first user of DMA_PREP_REPEAT with a > >>> non-interleaved transaction to do so. Your comment here seems to > >>> contract that. Which way do you want to go ? > >> > >> I would like to change the language of the explanation to not forbid > >> other uses, but they would be enabled in txn when we have users.. > > > > The documentation isn't set in stone, it can be updated when support for > > DMA_PREP_REPEAT will be enabled in other transaction types. I think it's > > better to have the documentation and code match, the documentation > > should describe the current implementation. I can add an additional > > sentence at the end of the paragraph to state "Support for this flag in > > other transaction types may be added in the future if the need arises." > > if that makes you feel better about it. > > Okay I will be okay with that caveat > > >>>> 2. DMA_PREP_REPEAT telling the transaction shall be automatically > >>>> repeated is okay. No issues with that > >>>> > >>>>> + * @DMA_PREP_LOAD_EOT: tell the driver that the transaction shall replaced any > >>>> > >>>> s/replaced/replace > >>>> > >>>>> + * active repeated (as indicated by DMA_PREP_REPEAT) transaction when the > >>>>> + * repeated transaction terminate. Not setting this flag when the previously > >>>>> + * queued transaction is marked with DMA_PREP_REPEAT will cause the new > >>>>> + * transaction to never be processed and stay in the issued queue forever. > >>>>> + * The flag is ignored if the previous transaction is not a repeated > >>>>> + * transaction. > >>>> > >>>> I am happy with this bit, I think we dont need to specify something like > >>>> DMA_PREP_LOAD_NEXT given the explanation here, so adding > >>>> DMA_PREP_LOAD_EOT would mean that. > >>> > >>> Just to clarify, does that mean I don't need to add a DMA_PREP_LOAD_NEXT > >>> flag in the API ? > >>> > >>>> Can we add a corresponding EOB as well to complete this > >>> > >>> What's EOB ? > >> > >> End of Burst, DMA would complete current burst and then terminate. I do > >> understand it is not applicable for your case as your hw doesn't support > >> it and would be unused but this is another case which would be useful so > >> for completeness we should add this > > > > Why not add it when we'll have a user for it ? How can you otherwise > > guarantee that it's a correct API if there's not even a single user that > > we can test the design with ? > > Okay lets not add but add a note that additional flags can be added when > required like EOB > > Also can we add a note in Documentation about these flags and how they > should be used for repeating transactions. Done, and I've added the notes regarding future extensions (support of non-interleaved repeated transactions, and EOB) there too, as it made more sense than in the header file. The new patches are in your mailbox :-) -- Regards, Laurent Pinchart ^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH v5 4/6] dmaengine: xilinx: dpdma: Add the Xilinx DisplayPort DMA engine driver 2020-05-28 2:52 [PATCH v5 0/6] dma: Add Xilinx ZynqMP DPDMA driver Laurent Pinchart ` (2 preceding siblings ...) 2020-05-28 2:52 ` [PATCH v5 3/6] dmaengine: Add support for repeating transactions Laurent Pinchart @ 2020-05-28 2:52 ` Laurent Pinchart 2020-07-03 17:32 ` Vinod Koul 2020-05-28 2:52 ` [PATCH v5 5/6] dmaengine: xilinx: dpdma: Add debugfs support Laurent Pinchart ` (2 subsequent siblings) 6 siblings, 1 reply; 18+ messages in thread From: Laurent Pinchart @ 2020-05-28 2:52 UTC (permalink / raw) To: dmaengine Cc: Michal Simek, Hyun Kwon, Tejas Upadhyay, Satish Kumar Nagireddy, Vinod Koul, Peter Ujfalusi From: Hyun Kwon <hyun.kwon@xilinx.com> The ZynqMP DisplayPort subsystem includes a DMA engine called DPDMA with 6 DMa channels (4 for display and 2 for audio). This driver exposes the DPDMA through the dmaengine API, to be used by audio (ALSA) and display (DRM) drivers for the DisplayPort subsystem. Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com> Signed-off-by: Tejas Upadhyay <tejasu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> --- Changes since v4: - Support DMA_PREP_LOAD_EOT, ignoring any transaction that doesn't have the flag set, as requested in the review of v4 Changes since v3: - Fix uninitialized variable in xilinx_dpdma_config() - Free pending and active descriptors upon termination - Switch to DMA_PREP_REPEAT Changes since v2: - Switch to virt-dma - Support interleaved cyclic transfers and nothing else - Fix terminate_all behaviour (don't wait) - Fix bug in extended address handling for hw desc - Clean up video group handling - Update driver name - Use macros for bitfields - Remove unneeded header - Coding style and typo fixes Changes since v1: - Remove unneeded #include - Drop enum xilinx_dpdma_chan_id - Update compatible string - Drop DT subnodes - Replace XILINX_DPDMA_NUM_CHAN with ARRAY_SIZE(xdev->chan) - Disable IRQ at remove() time - Use devm_platform_ioremap_resource() - Don't inline functions manually - Add section headers - Merge DMA engine implementation in their wrappers - Rename xilinx_dpdma_sw_desc::phys to dma_addr - Use GENMASK() - Use FIELD_PREP/FIELD_GET - Fix MSB handling in xilinx_dpdma_sw_desc_addr_64() - Fix logic in xilinx_dpdma_chan_prep_slave_sg() - Document why xilinx_dpdma_config() doesn't need to check most parameters - Remove debugfs support - Rechedule errored descriptor - Align the line size with 128bit - SPDX header formatting --- MAINTAINERS | 1 + drivers/dma/Kconfig | 10 + drivers/dma/xilinx/Makefile | 1 + drivers/dma/xilinx/xilinx_dpdma.c | 1554 +++++++++++++++++++++++++++++ 4 files changed, 1566 insertions(+) create mode 100644 drivers/dma/xilinx/xilinx_dpdma.c diff --git a/MAINTAINERS b/MAINTAINERS index 97a7de450cb4..30f58b6c9f98 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -18594,6 +18594,7 @@ M: Laurent Pinchart <laurent.pinchart@ideasonboard.com> L: dmaengine@vger.kernel.org S: Supported F: Documentation/devicetree/bindings/dma/xilinx/xlnx,zynqmp-dpdma.yaml +F: drivers/dma/xilinx/xilinx_dpdma.c F: include/dt-bindings/dma/xlnx-zynqmp-dpdma.h XILLYBUS DRIVER diff --git a/drivers/dma/Kconfig b/drivers/dma/Kconfig index 092483644315..61565e039602 100644 --- a/drivers/dma/Kconfig +++ b/drivers/dma/Kconfig @@ -708,6 +708,16 @@ config XILINX_ZYNQMP_DMA help Enable support for Xilinx ZynqMP DMA controller. +config XILINX_ZYNQMP_DPDMA + tristate "Xilinx DPDMA Engine" + select DMA_ENGINE + select DMA_VIRTUAL_CHANNELS + help + Enable support for Xilinx ZynqMP DisplayPort DMA. Choose this option + if you have a Xilinx ZynqMP SoC with a DisplayPort subsystem. The + driver provides the dmaengine required by the DisplayPort subsystem + display driver. + config ZX_DMA tristate "ZTE ZX DMA support" depends on ARCH_ZX || COMPILE_TEST diff --git a/drivers/dma/xilinx/Makefile b/drivers/dma/xilinx/Makefile index e921de575b55..767bb45f641f 100644 --- a/drivers/dma/xilinx/Makefile +++ b/drivers/dma/xilinx/Makefile @@ -1,3 +1,4 @@ # SPDX-License-Identifier: GPL-2.0-only obj-$(CONFIG_XILINX_DMA) += xilinx_dma.o obj-$(CONFIG_XILINX_ZYNQMP_DMA) += zynqmp_dma.o +obj-$(CONFIG_XILINX_ZYNQMP_DPDMA) += xilinx_dpdma.o diff --git a/drivers/dma/xilinx/xilinx_dpdma.c b/drivers/dma/xilinx/xilinx_dpdma.c new file mode 100644 index 000000000000..227f8b083d1f --- /dev/null +++ b/drivers/dma/xilinx/xilinx_dpdma.c @@ -0,0 +1,1554 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Xilinx ZynqMP DPDMA Engine driver + * + * Copyright (C) 2015 - 2019 Xilinx, Inc. + * + * Author: Hyun Woo Kwon <hyun.kwon@xilinx.com> + */ + +#include <linux/bitfield.h> +#include <linux/bits.h> +#include <linux/clk.h> +#include <linux/delay.h> +#include <linux/dmaengine.h> +#include <linux/dmapool.h> +#include <linux/interrupt.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_dma.h> +#include <linux/platform_device.h> +#include <linux/sched.h> +#include <linux/slab.h> +#include <linux/spinlock.h> +#include <linux/wait.h> + +#include <dt-bindings/dma/xlnx-zynqmp-dpdma.h> + +#include "../dmaengine.h" +#include "../virt-dma.h" + +/* DPDMA registers */ +#define XILINX_DPDMA_ERR_CTRL 0x000 +#define XILINX_DPDMA_ISR 0x004 +#define XILINX_DPDMA_IMR 0x008 +#define XILINX_DPDMA_IEN 0x00c +#define XILINX_DPDMA_IDS 0x010 +#define XILINX_DPDMA_INTR_DESC_DONE(n) BIT((n) + 0) +#define XILINX_DPDMA_INTR_DESC_DONE_MASK GENMASK(5, 0) +#define XILINX_DPDMA_INTR_NO_OSTAND(n) BIT((n) + 6) +#define XILINX_DPDMA_INTR_NO_OSTAND_MASK GENMASK(11, 6) +#define XILINX_DPDMA_INTR_AXI_ERR(n) BIT((n) + 12) +#define XILINX_DPDMA_INTR_AXI_ERR_MASK GENMASK(17, 12) +#define XILINX_DPDMA_INTR_DESC_ERR(n) BIT((n) + 16) +#define XILINX_DPDMA_INTR_DESC_ERR_MASK GENMASK(23, 18) +#define XILINX_DPDMA_INTR_WR_CMD_FIFO_FULL BIT(24) +#define XILINX_DPDMA_INTR_WR_DATA_FIFO_FULL BIT(25) +#define XILINX_DPDMA_INTR_AXI_4K_CROSS BIT(26) +#define XILINX_DPDMA_INTR_VSYNC BIT(27) +#define XILINX_DPDMA_INTR_CHAN_ERR_MASK 0x00041000 +#define XILINX_DPDMA_INTR_CHAN_ERR 0x00fff000 +#define XILINX_DPDMA_INTR_GLOBAL_ERR 0x07000000 +#define XILINX_DPDMA_INTR_ERR_ALL 0x07fff000 +#define XILINX_DPDMA_INTR_CHAN_MASK 0x00041041 +#define XILINX_DPDMA_INTR_GLOBAL_MASK 0x0f000000 +#define XILINX_DPDMA_INTR_ALL 0x0fffffff +#define XILINX_DPDMA_EISR 0x014 +#define XILINX_DPDMA_EIMR 0x018 +#define XILINX_DPDMA_EIEN 0x01c +#define XILINX_DPDMA_EIDS 0x020 +#define XILINX_DPDMA_EINTR_INV_APB BIT(0) +#define XILINX_DPDMA_EINTR_RD_AXI_ERR(n) BIT((n) + 1) +#define XILINX_DPDMA_EINTR_RD_AXI_ERR_MASK GENMASK(6, 1) +#define XILINX_DPDMA_EINTR_PRE_ERR(n) BIT((n) + 7) +#define XILINX_DPDMA_EINTR_PRE_ERR_MASK GENMASK(12, 7) +#define XILINX_DPDMA_EINTR_CRC_ERR(n) BIT((n) + 13) +#define XILINX_DPDMA_EINTR_CRC_ERR_MASK GENMASK(18, 13) +#define XILINX_DPDMA_EINTR_WR_AXI_ERR(n) BIT((n) + 19) +#define XILINX_DPDMA_EINTR_WR_AXI_ERR_MASK GENMASK(24, 19) +#define XILINX_DPDMA_EINTR_DESC_DONE_ERR(n) BIT((n) + 25) +#define XILINX_DPDMA_EINTR_DESC_DONE_ERR_MASK GENMASK(30, 25) +#define XILINX_DPDMA_EINTR_RD_CMD_FIFO_FULL BIT(32) +#define XILINX_DPDMA_EINTR_CHAN_ERR_MASK 0x02082082 +#define XILINX_DPDMA_EINTR_CHAN_ERR 0x7ffffffe +#define XILINX_DPDMA_EINTR_GLOBAL_ERR 0x80000001 +#define XILINX_DPDMA_EINTR_ALL 0xffffffff +#define XILINX_DPDMA_CNTL 0x100 +#define XILINX_DPDMA_GBL 0x104 +#define XILINX_DPDMA_GBL_TRIG_MASK(n) ((n) << 0) +#define XILINX_DPDMA_GBL_RETRIG_MASK(n) ((n) << 6) +#define XILINX_DPDMA_ALC0_CNTL 0x108 +#define XILINX_DPDMA_ALC0_STATUS 0x10c +#define XILINX_DPDMA_ALC0_MAX 0x110 +#define XILINX_DPDMA_ALC0_MIN 0x114 +#define XILINX_DPDMA_ALC0_ACC 0x118 +#define XILINX_DPDMA_ALC0_ACC_TRAN 0x11c +#define XILINX_DPDMA_ALC1_CNTL 0x120 +#define XILINX_DPDMA_ALC1_STATUS 0x124 +#define XILINX_DPDMA_ALC1_MAX 0x128 +#define XILINX_DPDMA_ALC1_MIN 0x12c +#define XILINX_DPDMA_ALC1_ACC 0x130 +#define XILINX_DPDMA_ALC1_ACC_TRAN 0x134 + +/* Channel register */ +#define XILINX_DPDMA_CH_BASE 0x200 +#define XILINX_DPDMA_CH_OFFSET 0x100 +#define XILINX_DPDMA_CH_DESC_START_ADDRE 0x000 +#define XILINX_DPDMA_CH_DESC_START_ADDRE_MASK GENMASK(15, 0) +#define XILINX_DPDMA_CH_DESC_START_ADDR 0x004 +#define XILINX_DPDMA_CH_DESC_NEXT_ADDRE 0x008 +#define XILINX_DPDMA_CH_DESC_NEXT_ADDR 0x00c +#define XILINX_DPDMA_CH_PYLD_CUR_ADDRE 0x010 +#define XILINX_DPDMA_CH_PYLD_CUR_ADDR 0x014 +#define XILINX_DPDMA_CH_CNTL 0x018 +#define XILINX_DPDMA_CH_CNTL_ENABLE BIT(0) +#define XILINX_DPDMA_CH_CNTL_PAUSE BIT(1) +#define XILINX_DPDMA_CH_CNTL_QOS_DSCR_WR_MASK GENMASK(5, 2) +#define XILINX_DPDMA_CH_CNTL_QOS_DSCR_RD_MASK GENMASK(9, 6) +#define XILINX_DPDMA_CH_CNTL_QOS_DATA_RD_MASK GENMASK(13, 10) +#define XILINX_DPDMA_CH_CNTL_QOS_VID_CLASS 11 +#define XILINX_DPDMA_CH_STATUS 0x01c +#define XILINX_DPDMA_CH_STATUS_OTRAN_CNT_MASK GENMASK(24, 21) +#define XILINX_DPDMA_CH_VDO 0x020 +#define XILINX_DPDMA_CH_PYLD_SZ 0x024 +#define XILINX_DPDMA_CH_DESC_ID 0x028 + +/* DPDMA descriptor fields */ +#define XILINX_DPDMA_DESC_CONTROL_PREEMBLE 0xa5 +#define XILINX_DPDMA_DESC_CONTROL_COMPLETE_INTR BIT(8) +#define XILINX_DPDMA_DESC_CONTROL_DESC_UPDATE BIT(9) +#define XILINX_DPDMA_DESC_CONTROL_IGNORE_DONE BIT(10) +#define XILINX_DPDMA_DESC_CONTROL_FRAG_MODE BIT(18) +#define XILINX_DPDMA_DESC_CONTROL_LAST BIT(19) +#define XILINX_DPDMA_DESC_CONTROL_ENABLE_CRC BIT(20) +#define XILINX_DPDMA_DESC_CONTROL_LAST_OF_FRAME BIT(21) +#define XILINX_DPDMA_DESC_ID_MASK GENMASK(15, 0) +#define XILINX_DPDMA_DESC_HSIZE_STRIDE_HSIZE_MASK GENMASK(17, 0) +#define XILINX_DPDMA_DESC_HSIZE_STRIDE_STRIDE_MASK GENMASK(31, 18) +#define XILINX_DPDMA_DESC_ADDR_EXT_NEXT_ADDR_MASK GENMASK(15, 0) +#define XILINX_DPDMA_DESC_ADDR_EXT_SRC_ADDR_MASK GENMASK(31, 16) + +#define XILINX_DPDMA_ALIGN_BYTES 256 +#define XILINX_DPDMA_LINESIZE_ALIGN_BITS 128 + +#define XILINX_DPDMA_NUM_CHAN 6 + +struct xilinx_dpdma_chan; + +/** + * struct xilinx_dpdma_hw_desc - DPDMA hardware descriptor + * @control: control configuration field + * @desc_id: descriptor ID + * @xfer_size: transfer size + * @hsize_stride: horizontal size and stride + * @timestamp_lsb: LSB of time stamp + * @timestamp_msb: MSB of time stamp + * @addr_ext: upper 16 bit of 48 bit address (next_desc and src_addr) + * @next_desc: next descriptor 32 bit address + * @src_addr: payload source address (1st page, 32 LSB) + * @addr_ext_23: payload source address (3nd and 3rd pages, 16 LSBs) + * @addr_ext_45: payload source address (4th and 5th pages, 16 LSBs) + * @src_addr2: payload source address (2nd page, 32 LSB) + * @src_addr3: payload source address (3rd page, 32 LSB) + * @src_addr4: payload source address (4th page, 32 LSB) + * @src_addr5: payload source address (5th page, 32 LSB) + * @crc: descriptor CRC + */ +struct xilinx_dpdma_hw_desc { + u32 control; + u32 desc_id; + u32 xfer_size; + u32 hsize_stride; + u32 timestamp_lsb; + u32 timestamp_msb; + u32 addr_ext; + u32 next_desc; + u32 src_addr; + u32 addr_ext_23; + u32 addr_ext_45; + u32 src_addr2; + u32 src_addr3; + u32 src_addr4; + u32 src_addr5; + u32 crc; +} __aligned(XILINX_DPDMA_ALIGN_BYTES); + +/** + * struct xilinx_dpdma_sw_desc - DPDMA software descriptor + * @hw: DPDMA hardware descriptor + * @node: list node for software descriptors + * @dma_addr: DMA address of the software descriptor + */ +struct xilinx_dpdma_sw_desc { + struct xilinx_dpdma_hw_desc hw; + struct list_head node; + dma_addr_t dma_addr; +}; + +/** + * struct xilinx_dpdma_tx_desc - DPDMA transaction descriptor + * @vdesc: virtual DMA descriptor + * @chan: DMA channel + * @descriptors: list of software descriptors + * @error: an error has been detected with this descriptor + */ +struct xilinx_dpdma_tx_desc { + struct virt_dma_desc vdesc; + struct xilinx_dpdma_chan *chan; + struct list_head descriptors; + bool error; +}; + +#define to_dpdma_tx_desc(_desc) \ + container_of(_desc, struct xilinx_dpdma_tx_desc, vdesc) + +/** + * struct xilinx_dpdma_chan - DPDMA channel + * @vchan: virtual DMA channel + * @reg: register base address + * @id: channel ID + * @wait_to_stop: queue to wait for outstanding transacitons before stopping + * @running: true if the channel is running + * @first_frame: flag for the first frame of stream + * @video_group: flag if multi-channel operation is needed for video channels + * @lock: lock to access struct xilinx_dpdma_chan + * @desc_pool: descriptor allocation pool + * @err_task: error IRQ bottom half handler + * @desc.pending: Descriptor schedule to the hardware, pending execution + * @desc.active: Descriptor being executed by the hardware + * @xdev: DPDMA device + */ +struct xilinx_dpdma_chan { + struct virt_dma_chan vchan; + void __iomem *reg; + unsigned int id; + + wait_queue_head_t wait_to_stop; + bool running; + bool first_frame; + bool video_group; + + spinlock_t lock; /* lock to access struct xilinx_dpdma_chan */ + struct dma_pool *desc_pool; + struct tasklet_struct err_task; + + struct { + struct xilinx_dpdma_tx_desc *pending; + struct xilinx_dpdma_tx_desc *active; + } desc; + + struct xilinx_dpdma_device *xdev; +}; + +#define to_xilinx_chan(_chan) \ + container_of(_chan, struct xilinx_dpdma_chan, vchan.chan) + +/** + * struct xilinx_dpdma_device - DPDMA device + * @common: generic dma device structure + * @reg: register base address + * @dev: generic device structure + * @irq: the interrupt number + * @axi_clk: axi clock + * @chan: DPDMA channels + * @ext_addr: flag for 64 bit system (48 bit addressing) + */ +struct xilinx_dpdma_device { + struct dma_device common; + void __iomem *reg; + struct device *dev; + int irq; + + struct clk *axi_clk; + struct xilinx_dpdma_chan *chan[XILINX_DPDMA_NUM_CHAN]; + + bool ext_addr; +}; + +/* ----------------------------------------------------------------------------- + * I/O Accessors + */ + +static inline u32 dpdma_read(void __iomem *base, u32 offset) +{ + return ioread32(base + offset); +} + +static inline void dpdma_write(void __iomem *base, u32 offset, u32 val) +{ + iowrite32(val, base + offset); +} + +static inline void dpdma_clr(void __iomem *base, u32 offset, u32 clr) +{ + dpdma_write(base, offset, dpdma_read(base, offset) & ~clr); +} + +static inline void dpdma_set(void __iomem *base, u32 offset, u32 set) +{ + dpdma_write(base, offset, dpdma_read(base, offset) | set); +} + +/* ----------------------------------------------------------------------------- + * Descriptor Operations + */ + +/** + * xilinx_dpdma_sw_desc_set_dma_addrs - Set DMA addresses in the descriptor + * @sw_desc: The software descriptor in which to set DMA addresses + * @prev: The previous descriptor + * @dma_addr: array of dma addresses + * @num_src_addr: number of addresses in @dma_addr + * + * Set all the DMA addresses in the hardware descriptor corresponding to @dev + * from @dma_addr. If a previous descriptor is specified in @prev, its next + * descriptor DMA address is set to the DMA address of @sw_desc. @prev may be + * identical to @sw_desc for cyclic transfers. + */ +static void xilinx_dpdma_sw_desc_set_dma_addrs(struct xilinx_dpdma_device *xdev, + struct xilinx_dpdma_sw_desc *sw_desc, + struct xilinx_dpdma_sw_desc *prev, + dma_addr_t dma_addr[], + unsigned int num_src_addr) +{ + struct xilinx_dpdma_hw_desc *hw_desc = &sw_desc->hw; + unsigned int i; + + hw_desc->src_addr = lower_32_bits(dma_addr[0]); + if (xdev->ext_addr) + hw_desc->addr_ext |= + FIELD_PREP(XILINX_DPDMA_DESC_ADDR_EXT_SRC_ADDR_MASK, + upper_32_bits(dma_addr[0])); + + for (i = 1; i < num_src_addr; i++) { + u32 *addr = &hw_desc->src_addr2; + + addr[i-1] = lower_32_bits(dma_addr[i]); + + if (xdev->ext_addr) { + u32 *addr_ext = &hw_desc->addr_ext_23; + u32 addr_msb; + + addr_msb = upper_32_bits(dma_addr[i]) & GENMASK(15, 0); + addr_msb <<= 16 * ((i - 1) % 2); + addr_ext[(i - 1) / 2] |= addr_msb; + } + } + + if (!prev) + return; + + prev->hw.next_desc = lower_32_bits(sw_desc->dma_addr); + if (xdev->ext_addr) + prev->hw.addr_ext |= + FIELD_PREP(XILINX_DPDMA_DESC_ADDR_EXT_NEXT_ADDR_MASK, + upper_32_bits(sw_desc->dma_addr)); +} + +/** + * xilinx_dpdma_chan_alloc_sw_desc - Allocate a software descriptor + * @chan: DPDMA channel + * + * Allocate a software descriptor from the channel's descriptor pool. + * + * Return: a software descriptor or NULL. + */ +static struct xilinx_dpdma_sw_desc * +xilinx_dpdma_chan_alloc_sw_desc(struct xilinx_dpdma_chan *chan) +{ + struct xilinx_dpdma_sw_desc *sw_desc; + dma_addr_t dma_addr; + + sw_desc = dma_pool_zalloc(chan->desc_pool, GFP_ATOMIC, &dma_addr); + if (!sw_desc) + return NULL; + + sw_desc->dma_addr = dma_addr; + + return sw_desc; +} + +/** + * xilinx_dpdma_chan_free_sw_desc - Free a software descriptor + * @chan: DPDMA channel + * @sw_desc: software descriptor to free + * + * Free a software descriptor from the channel's descriptor pool. + */ +static void +xilinx_dpdma_chan_free_sw_desc(struct xilinx_dpdma_chan *chan, + struct xilinx_dpdma_sw_desc *sw_desc) +{ + dma_pool_free(chan->desc_pool, sw_desc, sw_desc->dma_addr); +} + +/** + * xilinx_dpdma_chan_dump_tx_desc - Dump a tx descriptor + * @chan: DPDMA channel + * @tx_desc: tx descriptor to dump + * + * Dump contents of a tx descriptor + */ +static void xilinx_dpdma_chan_dump_tx_desc(struct xilinx_dpdma_chan *chan, + struct xilinx_dpdma_tx_desc *tx_desc) +{ + struct xilinx_dpdma_sw_desc *sw_desc; + struct device *dev = chan->xdev->dev; + unsigned int i = 0; + + dev_dbg(dev, "------- TX descriptor dump start -------\n"); + dev_dbg(dev, "------- channel ID = %d -------\n", chan->id); + + list_for_each_entry(sw_desc, &tx_desc->descriptors, node) { + struct xilinx_dpdma_hw_desc *hw_desc = &sw_desc->hw; + + dev_dbg(dev, "------- HW descriptor %d -------\n", i++); + dev_dbg(dev, "descriptor DMA addr: %pad\n", &sw_desc->dma_addr); + dev_dbg(dev, "control: 0x%08x\n", hw_desc->control); + dev_dbg(dev, "desc_id: 0x%08x\n", hw_desc->desc_id); + dev_dbg(dev, "xfer_size: 0x%08x\n", hw_desc->xfer_size); + dev_dbg(dev, "hsize_stride: 0x%08x\n", hw_desc->hsize_stride); + dev_dbg(dev, "timestamp_lsb: 0x%08x\n", hw_desc->timestamp_lsb); + dev_dbg(dev, "timestamp_msb: 0x%08x\n", hw_desc->timestamp_msb); + dev_dbg(dev, "addr_ext: 0x%08x\n", hw_desc->addr_ext); + dev_dbg(dev, "next_desc: 0x%08x\n", hw_desc->next_desc); + dev_dbg(dev, "src_addr: 0x%08x\n", hw_desc->src_addr); + dev_dbg(dev, "addr_ext_23: 0x%08x\n", hw_desc->addr_ext_23); + dev_dbg(dev, "addr_ext_45: 0x%08x\n", hw_desc->addr_ext_45); + dev_dbg(dev, "src_addr2: 0x%08x\n", hw_desc->src_addr2); + dev_dbg(dev, "src_addr3: 0x%08x\n", hw_desc->src_addr3); + dev_dbg(dev, "src_addr4: 0x%08x\n", hw_desc->src_addr4); + dev_dbg(dev, "src_addr5: 0x%08x\n", hw_desc->src_addr5); + dev_dbg(dev, "crc: 0x%08x\n", hw_desc->crc); + } + + dev_dbg(dev, "------- TX descriptor dump end -------\n"); +} + +/** + * xilinx_dpdma_chan_alloc_tx_desc - Allocate a transaction descriptor + * @chan: DPDMA channel + * + * Allocate a tx descriptor. + * + * Return: a tx descriptor or NULL. + */ +static struct xilinx_dpdma_tx_desc * +xilinx_dpdma_chan_alloc_tx_desc(struct xilinx_dpdma_chan *chan) +{ + struct xilinx_dpdma_tx_desc *tx_desc; + + tx_desc = kzalloc(sizeof(*tx_desc), GFP_KERNEL); + if (!tx_desc) + return NULL; + + INIT_LIST_HEAD(&tx_desc->descriptors); + tx_desc->chan = chan; + tx_desc->error = false; + + return tx_desc; +} + +/** + * xilinx_dpdma_chan_free_tx_desc - Free a virtual DMA descriptor + * @vdesc: virtual DMA descriptor + * + * Free the virtual DMA descriptor @vdesc including its software descriptors. + */ +static void xilinx_dpdma_chan_free_tx_desc(struct virt_dma_desc *vdesc) +{ + struct xilinx_dpdma_sw_desc *sw_desc, *next; + struct xilinx_dpdma_tx_desc *desc; + + if (!vdesc) + return; + + desc = to_dpdma_tx_desc(vdesc); + + list_for_each_entry_safe(sw_desc, next, &desc->descriptors, node) { + list_del(&sw_desc->node); + xilinx_dpdma_chan_free_sw_desc(desc->chan, sw_desc); + } + + kfree(desc); +} + +/** + * xilinx_dpdma_chan_prep_interleaved_dma - Prepare an interleaved dma + * descriptor + * @chan: DPDMA channel + * @xt: dma interleaved template + * + * Prepare a tx descriptor including internal software/hardware descriptors + * based on @xt. + * + * Return: A DPDMA TX descriptor on success, or NULL. + */ +static struct xilinx_dpdma_tx_desc * +xilinx_dpdma_chan_prep_interleaved_dma(struct xilinx_dpdma_chan *chan, + struct dma_interleaved_template *xt) +{ + struct xilinx_dpdma_tx_desc *tx_desc; + struct xilinx_dpdma_sw_desc *sw_desc; + struct xilinx_dpdma_hw_desc *hw_desc; + size_t hsize = xt->sgl[0].size; + size_t stride = hsize + xt->sgl[0].icg; + + if (!IS_ALIGNED(xt->src_start, XILINX_DPDMA_ALIGN_BYTES)) { + dev_err(chan->xdev->dev, "buffer should be aligned at %d B\n", + XILINX_DPDMA_ALIGN_BYTES); + return NULL; + } + + tx_desc = xilinx_dpdma_chan_alloc_tx_desc(chan); + if (!tx_desc) + return NULL; + + sw_desc = xilinx_dpdma_chan_alloc_sw_desc(chan); + if (!sw_desc) { + xilinx_dpdma_chan_free_tx_desc(&tx_desc->vdesc); + return NULL; + } + + xilinx_dpdma_sw_desc_set_dma_addrs(chan->xdev, sw_desc, sw_desc, + &xt->src_start, 1); + + hw_desc = &sw_desc->hw; + hsize = ALIGN(hsize, XILINX_DPDMA_LINESIZE_ALIGN_BITS / 8); + hw_desc->xfer_size = hsize * xt->numf; + hw_desc->hsize_stride = + FIELD_PREP(XILINX_DPDMA_DESC_HSIZE_STRIDE_HSIZE_MASK, hsize) | + FIELD_PREP(XILINX_DPDMA_DESC_HSIZE_STRIDE_STRIDE_MASK, + stride / 16); + hw_desc->control |= XILINX_DPDMA_DESC_CONTROL_PREEMBLE; + hw_desc->control |= XILINX_DPDMA_DESC_CONTROL_COMPLETE_INTR; + hw_desc->control |= XILINX_DPDMA_DESC_CONTROL_IGNORE_DONE; + hw_desc->control |= XILINX_DPDMA_DESC_CONTROL_LAST_OF_FRAME; + + list_add_tail(&sw_desc->node, &tx_desc->descriptors); + + return tx_desc; +} + +/* ----------------------------------------------------------------------------- + * DPDMA Channel Operations + */ + +/** + * xilinx_dpdma_chan_enable - Enable the channel + * @chan: DPDMA channel + * + * Enable the channel and its interrupts. Set the QoS values for video class. + */ +static void xilinx_dpdma_chan_enable(struct xilinx_dpdma_chan *chan) +{ + u32 reg; + + reg = (XILINX_DPDMA_INTR_CHAN_MASK << chan->id) + | XILINX_DPDMA_INTR_GLOBAL_MASK; + dpdma_write(chan->xdev->reg, XILINX_DPDMA_IEN, reg); + reg = (XILINX_DPDMA_EINTR_CHAN_ERR_MASK << chan->id) + | XILINX_DPDMA_INTR_GLOBAL_ERR; + dpdma_write(chan->xdev->reg, XILINX_DPDMA_EIEN, reg); + + reg = XILINX_DPDMA_CH_CNTL_ENABLE + | FIELD_PREP(XILINX_DPDMA_CH_CNTL_QOS_DSCR_WR_MASK, + XILINX_DPDMA_CH_CNTL_QOS_VID_CLASS) + | FIELD_PREP(XILINX_DPDMA_CH_CNTL_QOS_DSCR_RD_MASK, + XILINX_DPDMA_CH_CNTL_QOS_VID_CLASS) + | FIELD_PREP(XILINX_DPDMA_CH_CNTL_QOS_DATA_RD_MASK, + XILINX_DPDMA_CH_CNTL_QOS_VID_CLASS); + dpdma_set(chan->reg, XILINX_DPDMA_CH_CNTL, reg); +} + +/** + * xilinx_dpdma_chan_disable - Disable the channel + * @chan: DPDMA channel + * + * Disable the channel and its interrupts. + */ +static void xilinx_dpdma_chan_disable(struct xilinx_dpdma_chan *chan) +{ + u32 reg; + + reg = XILINX_DPDMA_INTR_CHAN_MASK << chan->id; + dpdma_write(chan->xdev->reg, XILINX_DPDMA_IEN, reg); + reg = XILINX_DPDMA_EINTR_CHAN_ERR_MASK << chan->id; + dpdma_write(chan->xdev->reg, XILINX_DPDMA_EIEN, reg); + + dpdma_clr(chan->reg, XILINX_DPDMA_CH_CNTL, XILINX_DPDMA_CH_CNTL_ENABLE); +} + +/** + * xilinx_dpdma_chan_pause - Pause the channel + * @chan: DPDMA channel + * + * Pause the channel. + */ +static void xilinx_dpdma_chan_pause(struct xilinx_dpdma_chan *chan) +{ + dpdma_set(chan->reg, XILINX_DPDMA_CH_CNTL, XILINX_DPDMA_CH_CNTL_PAUSE); +} + +/** + * xilinx_dpdma_chan_unpause - Unpause the channel + * @chan: DPDMA channel + * + * Unpause the channel. + */ +static void xilinx_dpdma_chan_unpause(struct xilinx_dpdma_chan *chan) +{ + dpdma_clr(chan->reg, XILINX_DPDMA_CH_CNTL, XILINX_DPDMA_CH_CNTL_PAUSE); +} + +static u32 xilinx_dpdma_chan_video_group_ready(struct xilinx_dpdma_chan *chan) +{ + struct xilinx_dpdma_device *xdev = chan->xdev; + u32 channels = 0; + unsigned int i; + + for (i = ZYNQMP_DPDMA_VIDEO0; i <= ZYNQMP_DPDMA_VIDEO2; i++) { + if (xdev->chan[i]->video_group && !xdev->chan[i]->running) + return 0; + + if (xdev->chan[i]->video_group) + channels |= BIT(i); + } + + return channels; +} + +/** + * xilinx_dpdma_chan_queue_transfer - Queue the next transfer + * @chan: DPDMA channel + * + * Queue the next descriptor, if any, to the hardware. If the channel is + * stopped, start it first. Otherwise retrigger it with the next descriptor. + */ +static void xilinx_dpdma_chan_queue_transfer(struct xilinx_dpdma_chan *chan) +{ + struct xilinx_dpdma_device *xdev = chan->xdev; + struct xilinx_dpdma_sw_desc *sw_desc; + struct xilinx_dpdma_tx_desc *desc; + struct virt_dma_desc *vdesc; + u32 reg, channels; + + lockdep_assert_held(&chan->lock); + + if (chan->desc.pending) + return; + + if (!chan->running) { + xilinx_dpdma_chan_unpause(chan); + xilinx_dpdma_chan_enable(chan); + chan->first_frame = true; + chan->running = true; + } + + if (chan->video_group) + channels = xilinx_dpdma_chan_video_group_ready(chan); + else + channels = BIT(chan->id); + + if (!channels) + return; + + vdesc = vchan_next_desc(&chan->vchan); + if (!vdesc) + return; + + if (!chan->first_frame && !(vdesc->tx.flags & DMA_PREP_LOAD_EOT)) { + /* + * The client forgot to set the DMA_PREP_LOAD_EOT flag. The DMA + * engine API requires the channel to silently ignore the + * descriptor, leaving the client waiting forever for the new + * descriptor to be processed. + */ + return; + } + + desc = to_dpdma_tx_desc(vdesc); + chan->desc.pending = desc; + list_del(&desc->vdesc.node); + + /* + * Assign the cookie to descriptors in this transaction. Only 16 bit + * will be used, but it should be enough. + */ + list_for_each_entry(sw_desc, &desc->descriptors, node) + sw_desc->hw.desc_id = desc->vdesc.tx.cookie; + + sw_desc = list_first_entry(&desc->descriptors, + struct xilinx_dpdma_sw_desc, node); + dpdma_write(chan->reg, XILINX_DPDMA_CH_DESC_START_ADDR, + lower_32_bits(sw_desc->dma_addr)); + if (xdev->ext_addr) + dpdma_write(chan->reg, XILINX_DPDMA_CH_DESC_START_ADDRE, + FIELD_PREP(XILINX_DPDMA_CH_DESC_START_ADDRE_MASK, + upper_32_bits(sw_desc->dma_addr))); + + if (chan->first_frame) + reg = XILINX_DPDMA_GBL_TRIG_MASK(channels); + else + reg = XILINX_DPDMA_GBL_RETRIG_MASK(channels); + + chan->first_frame = false; + + dpdma_write(xdev->reg, XILINX_DPDMA_GBL, reg); +} + +/** + * xilinx_dpdma_chan_ostand - Number of outstanding transactions + * @chan: DPDMA channel + * + * Read and return the number of outstanding transactions from register. + * + * Return: Number of outstanding transactions from the status register. + */ +static u32 xilinx_dpdma_chan_ostand(struct xilinx_dpdma_chan *chan) +{ + return FIELD_GET(XILINX_DPDMA_CH_STATUS_OTRAN_CNT_MASK, + dpdma_read(chan->reg, XILINX_DPDMA_CH_STATUS)); +} + +/** + * xilinx_dpdma_chan_no_ostand - Notify no outstanding transaction event + * @chan: DPDMA channel + * + * Notify waiters for no outstanding event, so waiters can stop the channel + * safely. This function is supposed to be called when 'no outstanding' + * interrupt is generated. The 'no outstanding' interrupt is disabled and + * should be re-enabled when this event is handled. If the channel status + * register still shows some number of outstanding transactions, the interrupt + * remains enabled. + * + * Return: 0 on success. On failure, -EWOULDBLOCK if there's still outstanding + * transaction(s). + */ +static int xilinx_dpdma_chan_notify_no_ostand(struct xilinx_dpdma_chan *chan) +{ + u32 cnt; + + cnt = xilinx_dpdma_chan_ostand(chan); + if (cnt) { + dev_dbg(chan->xdev->dev, "%d outstanding transactions\n", cnt); + return -EWOULDBLOCK; + } + + /* Disable 'no outstanding' interrupt */ + dpdma_write(chan->xdev->reg, XILINX_DPDMA_IDS, + XILINX_DPDMA_INTR_NO_OSTAND(chan->id)); + wake_up(&chan->wait_to_stop); + + return 0; +} + +/** + * xilinx_dpdma_chan_wait_no_ostand - Wait for the no outstanding irq + * @chan: DPDMA channel + * + * Wait for the no outstanding transaction interrupt. This functions can sleep + * for 50ms. + * + * Return: 0 on success. On failure, -ETIMEOUT for time out, or the error code + * from wait_event_interruptible_timeout(). + */ +static int xilinx_dpdma_chan_wait_no_ostand(struct xilinx_dpdma_chan *chan) +{ + int ret; + + /* Wait for a no outstanding transaction interrupt upto 50msec */ + ret = wait_event_interruptible_timeout(chan->wait_to_stop, + !xilinx_dpdma_chan_ostand(chan), + msecs_to_jiffies(50)); + if (ret > 0) { + dpdma_write(chan->xdev->reg, XILINX_DPDMA_IEN, + XILINX_DPDMA_INTR_NO_OSTAND(chan->id)); + return 0; + } + + dev_err(chan->xdev->dev, "not ready to stop: %d trans\n", + xilinx_dpdma_chan_ostand(chan)); + + if (ret == 0) + return -ETIMEDOUT; + + return ret; +} + +/** + * xilinx_dpdma_chan_poll_no_ostand - Poll the outstanding transaction status + * @chan: DPDMA channel + * + * Poll the outstanding transaction status, and return when there's no + * outstanding transaction. This functions can be used in the interrupt context + * or where the atomicity is required. Calling thread may wait more than 50ms. + * + * Return: 0 on success, or -ETIMEDOUT. + */ +static int xilinx_dpdma_chan_poll_no_ostand(struct xilinx_dpdma_chan *chan) +{ + u32 cnt, loop = 50000; + + /* Poll at least for 50ms (20 fps). */ + do { + cnt = xilinx_dpdma_chan_ostand(chan); + udelay(1); + } while (loop-- > 0 && cnt); + + if (loop) { + dpdma_write(chan->xdev->reg, XILINX_DPDMA_IEN, + XILINX_DPDMA_INTR_NO_OSTAND(chan->id)); + return 0; + } + + dev_err(chan->xdev->dev, "not ready to stop: %d trans\n", + xilinx_dpdma_chan_ostand(chan)); + + return -ETIMEDOUT; +} + +/** + * xilinx_dpdma_chan_stop - Stop the channel + * @chan: DPDMA channel + * + * Stop a previously paused channel by first waiting for completion of all + * outstanding transaction and then disabling the channel. + * + * Return: 0 on success, or -ETIMEDOUT if the channel failed to stop. + */ +static int xilinx_dpdma_chan_stop(struct xilinx_dpdma_chan *chan) +{ + unsigned long flags; + int ret; + + ret = xilinx_dpdma_chan_wait_no_ostand(chan); + if (ret) + return ret; + + spin_lock_irqsave(&chan->lock, flags); + xilinx_dpdma_chan_disable(chan); + chan->running = false; + spin_unlock_irqrestore(&chan->lock, flags); + + return 0; +} + +/** + * xilinx_dpdma_chan_done_irq - Handle hardware descriptor completion + * @chan: DPDMA channel + * + * Handle completion of the currently active descriptor (@chan->desc.active). As + * we currently support cyclic transfers only, this just invokes the cyclic + * callback. The descriptor will be completed at the VSYNC interrupt when a new + * descriptor replaces it. + */ +static void xilinx_dpdma_chan_done_irq(struct xilinx_dpdma_chan *chan) +{ + struct xilinx_dpdma_tx_desc *active = chan->desc.active; + unsigned long flags; + + spin_lock_irqsave(&chan->lock, flags); + + if (active) + vchan_cyclic_callback(&active->vdesc); + else + dev_warn(chan->xdev->dev, + "DONE IRQ with no active descriptor!\n"); + + spin_unlock_irqrestore(&chan->lock, flags); +} + +/** + * xilinx_dpdma_chan_vsync_irq - Handle hardware descriptor scheduling + * @chan: DPDMA channel + * + * At VSYNC the active descriptor may have been replaced by the pending + * descriptor. Detect this through the DESC_ID and perform appropriate + * bookkeeping. + */ +static void xilinx_dpdma_chan_vsync_irq(struct xilinx_dpdma_chan *chan) +{ + struct xilinx_dpdma_tx_desc *pending; + struct xilinx_dpdma_sw_desc *sw_desc; + unsigned long flags; + u32 desc_id; + + spin_lock_irqsave(&chan->lock, flags); + + pending = chan->desc.pending; + if (!chan->running || !pending) + goto out; + + desc_id = dpdma_read(chan->reg, XILINX_DPDMA_CH_DESC_ID); + + /* If the retrigger raced with vsync, retry at the next frame. */ + sw_desc = list_first_entry(&pending->descriptors, + struct xilinx_dpdma_sw_desc, node); + if (sw_desc->hw.desc_id != desc_id) + goto out; + + /* + * Complete the active descriptor, if any, promote the pending + * descriptor to active, and queue the next transfer, if any. + */ + if (chan->desc.active) + vchan_cookie_complete(&chan->desc.active->vdesc); + chan->desc.active = pending; + chan->desc.pending = NULL; + + xilinx_dpdma_chan_queue_transfer(chan); + +out: + spin_unlock_irqrestore(&chan->lock, flags); +} + +/** + * xilinx_dpdma_chan_err - Detect any channel error + * @chan: DPDMA channel + * @isr: masked Interrupt Status Register + * @eisr: Error Interrupt Status Register + * + * Return: true if any channel error occurs, or false otherwise. + */ +static bool +xilinx_dpdma_chan_err(struct xilinx_dpdma_chan *chan, u32 isr, u32 eisr) +{ + if (!chan) + return false; + + if (chan->running && + ((isr & (XILINX_DPDMA_INTR_CHAN_ERR_MASK << chan->id)) || + (eisr & (XILINX_DPDMA_EINTR_CHAN_ERR_MASK << chan->id)))) + return true; + + return false; +} + +/** + * xilinx_dpdma_chan_handle_err - DPDMA channel error handling + * @chan: DPDMA channel + * + * This function is called when any channel error or any global error occurs. + * The function disables the paused channel by errors and determines + * if the current active descriptor can be rescheduled depending on + * the descriptor status. + */ +static void xilinx_dpdma_chan_handle_err(struct xilinx_dpdma_chan *chan) +{ + struct xilinx_dpdma_device *xdev = chan->xdev; + struct xilinx_dpdma_tx_desc *active; + unsigned long flags; + + spin_lock_irqsave(&chan->lock, flags); + + dev_dbg(xdev->dev, "cur desc addr = 0x%04x%08x\n", + dpdma_read(chan->reg, XILINX_DPDMA_CH_DESC_START_ADDRE), + dpdma_read(chan->reg, XILINX_DPDMA_CH_DESC_START_ADDR)); + dev_dbg(xdev->dev, "cur payload addr = 0x%04x%08x\n", + dpdma_read(chan->reg, XILINX_DPDMA_CH_PYLD_CUR_ADDRE), + dpdma_read(chan->reg, XILINX_DPDMA_CH_PYLD_CUR_ADDR)); + + xilinx_dpdma_chan_disable(chan); + chan->running = false; + + if (!chan->desc.active) + goto out_unlock; + + active = chan->desc.active; + chan->desc.active = NULL; + + xilinx_dpdma_chan_dump_tx_desc(chan, active); + + if (active->error) + dev_dbg(xdev->dev, "repeated error on desc\n"); + + /* Reschedule if there's no new descriptor */ + if (!chan->desc.pending && + list_empty(&chan->vchan.desc_issued)) { + active->error = true; + list_add_tail(&active->vdesc.node, + &chan->vchan.desc_issued); + } else { + xilinx_dpdma_chan_free_tx_desc(&active->vdesc); + } + +out_unlock: + spin_unlock_irqrestore(&chan->lock, flags); +} + +/* ----------------------------------------------------------------------------- + * DMA Engine Operations + */ + +static struct dma_async_tx_descriptor * +xilinx_dpdma_prep_interleaved_dma(struct dma_chan *dchan, + struct dma_interleaved_template *xt, + unsigned long flags) +{ + struct xilinx_dpdma_chan *chan = to_xilinx_chan(dchan); + struct xilinx_dpdma_tx_desc *desc; + + if (xt->dir != DMA_MEM_TO_DEV) + return NULL; + + if (!xt->numf || !xt->sgl[0].size) + return NULL; + + if (!(flags & DMA_PREP_REPEAT)) + return NULL; + + desc = xilinx_dpdma_chan_prep_interleaved_dma(chan, xt); + if (!desc) + return NULL; + + vchan_tx_prep(&chan->vchan, &desc->vdesc, flags | DMA_CTRL_ACK); + + return &desc->vdesc.tx; +} + +/** + * xilinx_dpdma_alloc_chan_resources - Allocate resources for the channel + * @dchan: DMA channel + * + * Allocate a descriptor pool for the channel. + * + * Return: 0 on success, or -ENOMEM if failed to allocate a pool. + */ +static int xilinx_dpdma_alloc_chan_resources(struct dma_chan *dchan) +{ + struct xilinx_dpdma_chan *chan = to_xilinx_chan(dchan); + size_t align = __alignof__(struct xilinx_dpdma_sw_desc); + + chan->desc_pool = dma_pool_create(dev_name(chan->xdev->dev), + chan->xdev->dev, + sizeof(struct xilinx_dpdma_sw_desc), + align, 0); + if (!chan->desc_pool) { + dev_err(chan->xdev->dev, + "failed to allocate a descriptor pool\n"); + return -ENOMEM; + } + + return 0; +} + +/** + * xilinx_dpdma_free_chan_resources - Free all resources for the channel + * @dchan: DMA channel + * + * Free resources associated with the virtual DMA channel, and destroy the + * descriptor pool. + */ +static void xilinx_dpdma_free_chan_resources(struct dma_chan *dchan) +{ + struct xilinx_dpdma_chan *chan = to_xilinx_chan(dchan); + + vchan_free_chan_resources(&chan->vchan); + + dma_pool_destroy(chan->desc_pool); + chan->desc_pool = NULL; +} + +static void xilinx_dpdma_issue_pending(struct dma_chan *dchan) +{ + struct xilinx_dpdma_chan *chan = to_xilinx_chan(dchan); + unsigned long flags; + + spin_lock_irqsave(&chan->vchan.lock, flags); + if (vchan_issue_pending(&chan->vchan)) + xilinx_dpdma_chan_queue_transfer(chan); + spin_unlock_irqrestore(&chan->vchan.lock, flags); +} + +static int xilinx_dpdma_config(struct dma_chan *dchan, + struct dma_slave_config *config) +{ + struct xilinx_dpdma_chan *chan = to_xilinx_chan(dchan); + unsigned long flags; + int ret = 0; + + if (config->direction != DMA_MEM_TO_DEV) + return -EINVAL; + + /* + * The destination address doesn't need to be specified as the DPDMA is + * hardwired to the destination (the DP controller). The transfer + * width, burst size and port window size are thus meaningless, they're + * fixed both on the DPDMA side and on the DP controller side. + */ + + spin_lock_irqsave(&chan->lock, flags); + + /* Can't reconfigure a running channel. */ + if (chan->running) { + ret = -EBUSY; + goto unlock; + } + + /* + * Abuse the slave_id to indicate that the channel is part of a video + * group. + */ + if (chan->id >= ZYNQMP_DPDMA_VIDEO0 && chan->id <= ZYNQMP_DPDMA_VIDEO2) + chan->video_group = config->slave_id != 0; + +unlock: + spin_unlock_irqrestore(&chan->lock, flags); + + return ret; +} + +static int xilinx_dpdma_pause(struct dma_chan *dchan) +{ + xilinx_dpdma_chan_pause(to_xilinx_chan(dchan)); + + return 0; +} + +static int xilinx_dpdma_resume(struct dma_chan *dchan) +{ + xilinx_dpdma_chan_unpause(to_xilinx_chan(dchan)); + + return 0; +} + +/** + * xilinx_dpdma_terminate_all - Terminate the channel and descriptors + * @dchan: DMA channel + * + * Pause the channel without waiting for ongoing transfers to complete. Waiting + * for completion is performed by xilinx_dpdma_synchronize() that will disable + * the channel to complete the stop. + * + * All the descriptors associated with the channel that are guaranteed not to + * be touched by the hardware. The pending and active descriptor are not + * touched, and will be freed either upon completion, or by + * xilinx_dpdma_synchronize(). + * + * Return: 0 on success, or -ETIMEDOUT if the channel failed to stop. + */ +static int xilinx_dpdma_terminate_all(struct dma_chan *dchan) +{ + struct xilinx_dpdma_chan *chan = to_xilinx_chan(dchan); + struct xilinx_dpdma_device *xdev = chan->xdev; + LIST_HEAD(descriptors); + unsigned long flags; + unsigned int i; + + /* Pause the channel (including the whole video group if applicable). */ + if (chan->video_group) { + for (i = ZYNQMP_DPDMA_VIDEO0; i <= ZYNQMP_DPDMA_VIDEO2; i++) { + if (xdev->chan[i]->video_group && + xdev->chan[i]->running) { + xilinx_dpdma_chan_pause(xdev->chan[i]); + xdev->chan[i]->video_group = false; + } + } + } else { + xilinx_dpdma_chan_pause(chan); + } + + /* Gather all the descriptors we can free and free them. */ + spin_lock_irqsave(&chan->vchan.lock, flags); + vchan_get_all_descriptors(&chan->vchan, &descriptors); + spin_unlock_irqrestore(&chan->vchan.lock, flags); + + vchan_dma_desc_free_list(&chan->vchan, &descriptors); + + return 0; +} + +/** + * xilinx_dpdma_synchronize - Synchronize callback execution + * @dchan: DMA channel + * + * Synchronizing callback execution ensures that all previously issued + * transfers have completed and all associated callbacks have been called and + * have returned. + * + * This function waits for the DMA channel to stop. It assumes it has been + * paused by a previous call to dmaengine_terminate_async(), and that no new + * pending descriptors have been issued with dma_async_issue_pending(). The + * behaviour is undefined otherwise. + */ +static void xilinx_dpdma_synchronize(struct dma_chan *dchan) +{ + struct xilinx_dpdma_chan *chan = to_xilinx_chan(dchan); + unsigned long flags; + + xilinx_dpdma_chan_stop(chan); + + spin_lock_irqsave(&chan->vchan.lock, flags); + if (chan->desc.pending) { + vchan_terminate_vdesc(&chan->desc.pending->vdesc); + chan->desc.pending = NULL; + } + if (chan->desc.active) { + vchan_terminate_vdesc(&chan->desc.active->vdesc); + chan->desc.active = NULL; + } + spin_unlock_irqrestore(&chan->vchan.lock, flags); + + vchan_synchronize(&chan->vchan); +} + +/* ----------------------------------------------------------------------------- + * Interrupt and Tasklet Handling + */ + +/** + * xilinx_dpdma_err - Detect any global error + * @isr: Interrupt Status Register + * @eisr: Error Interrupt Status Register + * + * Return: True if any global error occurs, or false otherwise. + */ +static bool xilinx_dpdma_err(u32 isr, u32 eisr) +{ + if (isr & XILINX_DPDMA_INTR_GLOBAL_ERR || + eisr & XILINX_DPDMA_EINTR_GLOBAL_ERR) + return true; + + return false; +} + +/** + * xilinx_dpdma_handle_err_irq - Handle DPDMA error interrupt + * @xdev: DPDMA device + * @isr: masked Interrupt Status Register + * @eisr: Error Interrupt Status Register + * + * Handle if any error occurs based on @isr and @eisr. This function disables + * corresponding error interrupts, and those should be re-enabled once handling + * is done. + */ +static void xilinx_dpdma_handle_err_irq(struct xilinx_dpdma_device *xdev, + u32 isr, u32 eisr) +{ + bool err = xilinx_dpdma_err(isr, eisr); + unsigned int i; + + dev_dbg_ratelimited(xdev->dev, + "error irq: isr = 0x%08x, eisr = 0x%08x\n", + isr, eisr); + + /* Disable channel error interrupts until errors are handled. */ + dpdma_write(xdev->reg, XILINX_DPDMA_IDS, + isr & ~XILINX_DPDMA_INTR_GLOBAL_ERR); + dpdma_write(xdev->reg, XILINX_DPDMA_EIDS, + eisr & ~XILINX_DPDMA_EINTR_GLOBAL_ERR); + + for (i = 0; i < ARRAY_SIZE(xdev->chan); i++) + if (err || xilinx_dpdma_chan_err(xdev->chan[i], isr, eisr)) + tasklet_schedule(&xdev->chan[i]->err_task); +} + +/** + * xilinx_dpdma_enable_irq - Enable interrupts + * @xdev: DPDMA device + * + * Enable interrupts. + */ +static void xilinx_dpdma_enable_irq(struct xilinx_dpdma_device *xdev) +{ + dpdma_write(xdev->reg, XILINX_DPDMA_IEN, XILINX_DPDMA_INTR_ALL); + dpdma_write(xdev->reg, XILINX_DPDMA_EIEN, XILINX_DPDMA_EINTR_ALL); +} + +/** + * xilinx_dpdma_disable_irq - Disable interrupts + * @xdev: DPDMA device + * + * Disable interrupts. + */ +static void xilinx_dpdma_disable_irq(struct xilinx_dpdma_device *xdev) +{ + dpdma_write(xdev->reg, XILINX_DPDMA_IDS, XILINX_DPDMA_INTR_ERR_ALL); + dpdma_write(xdev->reg, XILINX_DPDMA_EIDS, XILINX_DPDMA_EINTR_ALL); +} + +/** + * xilinx_dpdma_chan_err_task - Per channel tasklet for error handling + * @data: tasklet data to be casted to DPDMA channel structure + * + * Per channel error handling tasklet. This function waits for the outstanding + * transaction to complete and triggers error handling. After error handling, + * re-enable channel error interrupts, and restart the channel if needed. + */ +static void xilinx_dpdma_chan_err_task(unsigned long data) +{ + struct xilinx_dpdma_chan *chan = (struct xilinx_dpdma_chan *)data; + struct xilinx_dpdma_device *xdev = chan->xdev; + unsigned long flags; + + /* Proceed error handling even when polling fails. */ + xilinx_dpdma_chan_poll_no_ostand(chan); + + xilinx_dpdma_chan_handle_err(chan); + + dpdma_write(xdev->reg, XILINX_DPDMA_IEN, + XILINX_DPDMA_INTR_CHAN_ERR_MASK << chan->id); + dpdma_write(xdev->reg, XILINX_DPDMA_EIEN, + XILINX_DPDMA_EINTR_CHAN_ERR_MASK << chan->id); + + spin_lock_irqsave(&chan->lock, flags); + xilinx_dpdma_chan_queue_transfer(chan); + spin_unlock_irqrestore(&chan->lock, flags); +} + +static irqreturn_t xilinx_dpdma_irq_handler(int irq, void *data) +{ + struct xilinx_dpdma_device *xdev = data; + unsigned long mask; + unsigned int i; + u32 status; + u32 error; + + status = dpdma_read(xdev->reg, XILINX_DPDMA_ISR); + error = dpdma_read(xdev->reg, XILINX_DPDMA_EISR); + if (!status && !error) + return IRQ_NONE; + + dpdma_write(xdev->reg, XILINX_DPDMA_ISR, status); + dpdma_write(xdev->reg, XILINX_DPDMA_EISR, error); + + if (status & XILINX_DPDMA_INTR_VSYNC) { + /* + * There's a single VSYNC interrupt that needs to be processed + * by each running channel to update the active descriptor. + */ + for (i = 0; i < ARRAY_SIZE(xdev->chan); i++) { + struct xilinx_dpdma_chan *chan = xdev->chan[i]; + + if (chan) + xilinx_dpdma_chan_vsync_irq(chan); + } + } + + mask = FIELD_GET(XILINX_DPDMA_INTR_DESC_DONE_MASK, status); + if (mask) { + for_each_set_bit(i, &mask, ARRAY_SIZE(xdev->chan)) + xilinx_dpdma_chan_done_irq(xdev->chan[i]); + } + + mask = FIELD_GET(XILINX_DPDMA_INTR_NO_OSTAND_MASK, status); + if (mask) { + for_each_set_bit(i, &mask, ARRAY_SIZE(xdev->chan)) + xilinx_dpdma_chan_notify_no_ostand(xdev->chan[i]); + } + + mask = status & XILINX_DPDMA_INTR_ERR_ALL; + if (mask || error) + xilinx_dpdma_handle_err_irq(xdev, mask, error); + + return IRQ_HANDLED; +} + +/* ----------------------------------------------------------------------------- + * Initialization & Cleanup + */ + +static int xilinx_dpdma_chan_init(struct xilinx_dpdma_device *xdev, + unsigned int chan_id) +{ + struct xilinx_dpdma_chan *chan; + + chan = devm_kzalloc(xdev->dev, sizeof(*chan), GFP_KERNEL); + if (!chan) + return -ENOMEM; + + chan->id = chan_id; + chan->reg = xdev->reg + XILINX_DPDMA_CH_BASE + + XILINX_DPDMA_CH_OFFSET * chan->id; + chan->running = false; + chan->xdev = xdev; + + spin_lock_init(&chan->lock); + init_waitqueue_head(&chan->wait_to_stop); + + tasklet_init(&chan->err_task, xilinx_dpdma_chan_err_task, + (unsigned long)chan); + + chan->vchan.desc_free = xilinx_dpdma_chan_free_tx_desc; + vchan_init(&chan->vchan, &xdev->common); + + xdev->chan[chan->id] = chan; + + return 0; +} + +static void xilinx_dpdma_chan_remove(struct xilinx_dpdma_chan *chan) +{ + if (!chan) + return; + + tasklet_kill(&chan->err_task); + list_del(&chan->vchan.chan.device_node); +} + +static struct dma_chan *of_dma_xilinx_xlate(struct of_phandle_args *dma_spec, + struct of_dma *ofdma) +{ + struct xilinx_dpdma_device *xdev = ofdma->of_dma_data; + uint32_t chan_id = dma_spec->args[0]; + + if (chan_id >= ARRAY_SIZE(xdev->chan)) + return NULL; + + if (!xdev->chan[chan_id]) + return NULL; + + return dma_get_slave_channel(&xdev->chan[chan_id]->vchan.chan); +} + +static int xilinx_dpdma_probe(struct platform_device *pdev) +{ + struct xilinx_dpdma_device *xdev; + struct dma_device *ddev; + unsigned int i; + int ret; + + xdev = devm_kzalloc(&pdev->dev, sizeof(*xdev), GFP_KERNEL); + if (!xdev) + return -ENOMEM; + + xdev->dev = &pdev->dev; + xdev->ext_addr = sizeof(dma_addr_t) > 4; + + INIT_LIST_HEAD(&xdev->common.channels); + + platform_set_drvdata(pdev, xdev); + + xdev->axi_clk = devm_clk_get(xdev->dev, "axi_clk"); + if (IS_ERR(xdev->axi_clk)) + return PTR_ERR(xdev->axi_clk); + + xdev->reg = devm_platform_ioremap_resource(pdev, 0); + if (IS_ERR(xdev->reg)) + return PTR_ERR(xdev->reg); + + xdev->irq = platform_get_irq(pdev, 0); + if (xdev->irq < 0) { + dev_err(xdev->dev, "failed to get platform irq\n"); + return xdev->irq; + } + + ret = request_irq(xdev->irq, xilinx_dpdma_irq_handler, IRQF_SHARED, + dev_name(xdev->dev), xdev); + if (ret) { + dev_err(xdev->dev, "failed to request IRQ\n"); + return ret; + } + + ddev = &xdev->common; + ddev->dev = &pdev->dev; + + dma_cap_set(DMA_SLAVE, ddev->cap_mask); + dma_cap_set(DMA_PRIVATE, ddev->cap_mask); + dma_cap_set(DMA_INTERLEAVE, ddev->cap_mask); + dma_cap_set(DMA_REPEAT, ddev->cap_mask); + dma_cap_set(DMA_LOAD_EOT, ddev->cap_mask); + ddev->copy_align = fls(XILINX_DPDMA_ALIGN_BYTES - 1); + + ddev->device_alloc_chan_resources = xilinx_dpdma_alloc_chan_resources; + ddev->device_free_chan_resources = xilinx_dpdma_free_chan_resources; + ddev->device_prep_interleaved_dma = xilinx_dpdma_prep_interleaved_dma; + /* TODO: Can we achieve better granularity ? */ + ddev->device_tx_status = dma_cookie_status; + ddev->device_issue_pending = xilinx_dpdma_issue_pending; + ddev->device_config = xilinx_dpdma_config; + ddev->device_pause = xilinx_dpdma_pause; + ddev->device_resume = xilinx_dpdma_resume; + ddev->device_terminate_all = xilinx_dpdma_terminate_all; + ddev->device_synchronize = xilinx_dpdma_synchronize; + ddev->src_addr_widths = BIT(DMA_SLAVE_BUSWIDTH_UNDEFINED); + ddev->directions = BIT(DMA_MEM_TO_DEV); + ddev->residue_granularity = DMA_RESIDUE_GRANULARITY_DESCRIPTOR; + + for (i = 0; i < ARRAY_SIZE(xdev->chan); ++i) { + ret = xilinx_dpdma_chan_init(xdev, i); + if (ret < 0) { + dev_err(xdev->dev, "failed to initialize channel %u\n", + i); + goto error; + } + } + + ret = clk_prepare_enable(xdev->axi_clk); + if (ret) { + dev_err(xdev->dev, "failed to enable the axi clock\n"); + goto error; + } + + ret = dma_async_device_register(ddev); + if (ret) { + dev_err(xdev->dev, "failed to register the dma device\n"); + goto error_dma_async; + } + + ret = of_dma_controller_register(xdev->dev->of_node, + of_dma_xilinx_xlate, ddev); + if (ret) { + dev_err(xdev->dev, "failed to register DMA to DT DMA helper\n"); + goto error_of_dma; + } + + xilinx_dpdma_enable_irq(xdev); + + dev_info(&pdev->dev, "Xilinx DPDMA engine is probed\n"); + + return 0; + +error_of_dma: + dma_async_device_unregister(ddev); +error_dma_async: + clk_disable_unprepare(xdev->axi_clk); +error: + for (i = 0; i < ARRAY_SIZE(xdev->chan); i++) + xilinx_dpdma_chan_remove(xdev->chan[i]); + + free_irq(xdev->irq, xdev); + + return ret; +} + +static int xilinx_dpdma_remove(struct platform_device *pdev) +{ + struct xilinx_dpdma_device *xdev = platform_get_drvdata(pdev); + unsigned int i; + + /* Start by disabling the IRQ to avoid races during cleanup. */ + free_irq(xdev->irq, xdev); + + xilinx_dpdma_disable_irq(xdev); + of_dma_controller_free(pdev->dev.of_node); + dma_async_device_unregister(&xdev->common); + clk_disable_unprepare(xdev->axi_clk); + + for (i = 0; i < ARRAY_SIZE(xdev->chan); i++) + xilinx_dpdma_chan_remove(xdev->chan[i]); + + return 0; +} + +static const struct of_device_id xilinx_dpdma_of_match[] = { + { .compatible = "xlnx,zynqmp-dpdma",}, + { /* end of table */ }, +}; +MODULE_DEVICE_TABLE(of, xilinx_dpdma_of_match); + +static struct platform_driver xilinx_dpdma_driver = { + .probe = xilinx_dpdma_probe, + .remove = xilinx_dpdma_remove, + .driver = { + .name = "xilinx-zynqmp-dpdma", + .of_match_table = xilinx_dpdma_of_match, + }, +}; + +module_platform_driver(xilinx_dpdma_driver); + +MODULE_AUTHOR("Xilinx, Inc."); +MODULE_DESCRIPTION("Xilinx ZynqMP DPDMA driver"); +MODULE_LICENSE("GPL v2"); -- Regards, Laurent Pinchart ^ permalink raw reply related [flat|nested] 18+ messages in thread
* Re: [PATCH v5 4/6] dmaengine: xilinx: dpdma: Add the Xilinx DisplayPort DMA engine driver 2020-05-28 2:52 ` [PATCH v5 4/6] dmaengine: xilinx: dpdma: Add the Xilinx DisplayPort DMA engine driver Laurent Pinchart @ 2020-07-03 17:32 ` Vinod Koul 2020-07-03 17:43 ` Laurent Pinchart 0 siblings, 1 reply; 18+ messages in thread From: Vinod Koul @ 2020-07-03 17:32 UTC (permalink / raw) To: Laurent Pinchart Cc: dmaengine, Michal Simek, Hyun Kwon, Tejas Upadhyay, Satish Kumar Nagireddy, Peter Ujfalusi On 28-05-20, 05:52, Laurent Pinchart wrote: > +++ b/drivers/dma/xilinx/xilinx_dpdma.c > @@ -0,0 +1,1554 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Xilinx ZynqMP DPDMA Engine driver > + * > + * Copyright (C) 2015 - 2019 Xilinx, Inc. 2020 please > +static struct xilinx_dpdma_tx_desc * > +xilinx_dpdma_chan_alloc_tx_desc(struct xilinx_dpdma_chan *chan) > +{ > + struct xilinx_dpdma_tx_desc *tx_desc; > + > + tx_desc = kzalloc(sizeof(*tx_desc), GFP_KERNEL); GFP_NOWAIT please, this is called from a prep call so needs to be atomic context > +static int xilinx_dpdma_config(struct dma_chan *dchan, > + struct dma_slave_config *config) > +{ > + struct xilinx_dpdma_chan *chan = to_xilinx_chan(dchan); > + unsigned long flags; > + int ret = 0; > + > + if (config->direction != DMA_MEM_TO_DEV) > + return -EINVAL; sorry but direction is deprecated and supposed to be remove, can you please remove this > + > + /* > + * The destination address doesn't need to be specified as the DPDMA is > + * hardwired to the destination (the DP controller). The transfer > + * width, burst size and port window size are thus meaningless, they're > + * fixed both on the DPDMA side and on the DP controller side. > + */ > + > + spin_lock_irqsave(&chan->lock, flags); > + > + /* Can't reconfigure a running channel. */ > + if (chan->running) { > + ret = -EBUSY; > + goto unlock; > + } why does this part matter? The configuration is passed here and should be applied to next descriptor submitted, channel can be busy. > + > + /* > + * Abuse the slave_id to indicate that the channel is part of a video > + * group. > + */ Of course, what does video grp mean here? > + if (chan->id >= ZYNQMP_DPDMA_VIDEO0 && chan->id <= ZYNQMP_DPDMA_VIDEO2) > + chan->video_group = config->slave_id != 0; so only thing we care here is slave_id? What about dma burst parameters? -- ~Vinod ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH v5 4/6] dmaengine: xilinx: dpdma: Add the Xilinx DisplayPort DMA engine driver 2020-07-03 17:32 ` Vinod Koul @ 2020-07-03 17:43 ` Laurent Pinchart 0 siblings, 0 replies; 18+ messages in thread From: Laurent Pinchart @ 2020-07-03 17:43 UTC (permalink / raw) To: Vinod Koul Cc: dmaengine, Michal Simek, Hyun Kwon, Tejas Upadhyay, Satish Kumar Nagireddy, Peter Ujfalusi Hi Vinod, On Fri, Jul 03, 2020 at 11:02:39PM +0530, Vinod Koul wrote: > On 28-05-20, 05:52, Laurent Pinchart wrote: > > > +++ b/drivers/dma/xilinx/xilinx_dpdma.c > > @@ -0,0 +1,1554 @@ > > +// SPDX-License-Identifier: GPL-2.0 > > +/* > > + * Xilinx ZynqMP DPDMA Engine driver > > + * > > + * Copyright (C) 2015 - 2019 Xilinx, Inc. > > 2020 please I was accurate when the first version was submitted ;-) I'll update this. > > +static struct xilinx_dpdma_tx_desc * > > +xilinx_dpdma_chan_alloc_tx_desc(struct xilinx_dpdma_chan *chan) > > +{ > > + struct xilinx_dpdma_tx_desc *tx_desc; > > + > > + tx_desc = kzalloc(sizeof(*tx_desc), GFP_KERNEL); > > GFP_NOWAIT please, this is called from a prep call so needs to be atomic > context That's an easy change, but it's an annoying one. No user of this driver will ever prepare descriptors in atomic context. This would thus put unnecessary burden on the system memory, possibly depriving a real user of GFP_NOWAIT from precious memory. > > +static int xilinx_dpdma_config(struct dma_chan *dchan, > > + struct dma_slave_config *config) > > +{ > > + struct xilinx_dpdma_chan *chan = to_xilinx_chan(dchan); > > + unsigned long flags; > > + int ret = 0; > > + > > + if (config->direction != DMA_MEM_TO_DEV) > > + return -EINVAL; > > sorry but direction is deprecated and supposed to be remove, can you > please remove this Sure. Removing the direction field through the whole subsystem would be nice to avoid this mistake in new drivers. > > + > > + /* > > + * The destination address doesn't need to be specified as the DPDMA is > > + * hardwired to the destination (the DP controller). The transfer > > + * width, burst size and port window size are thus meaningless, they're > > + * fixed both on the DPDMA side and on the DP controller side. > > + */ > > + > > + spin_lock_irqsave(&chan->lock, flags); > > + > > + /* Can't reconfigure a running channel. */ > > + if (chan->running) { > > + ret = -EBUSY; > > + goto unlock; > > + } > > why does this part matter? The configuration is passed here and should > be applied to next descriptor submitted, channel can be busy. I'll drop it. > > + > > + /* > > + * Abuse the slave_id to indicate that the channel is part of a video > > + * group. > > + */ > > Of course, what does video grp mean here? When the frame to be displayed is made of multiple planes, multiple DMA channels have to be used, one per plane. The channels have to be synchronized and operated together by the driver. The video_group field is a boolean indicating that the channel is part of such a group. > > + if (chan->id >= ZYNQMP_DPDMA_VIDEO0 && chan->id <= ZYNQMP_DPDMA_VIDEO2) > > + chan->video_group = config->slave_id != 0; > > so only thing we care here is slave_id? What about dma burst parameters? The hardware hardware doesn't have any burst parameter that can be configured. It's a DMA engine dedicated to the display device, most parameters are thus hardcoded at the hardware level, as explained by the comment above. -- Regards, Laurent Pinchart ^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH v5 5/6] dmaengine: xilinx: dpdma: Add debugfs support 2020-05-28 2:52 [PATCH v5 0/6] dma: Add Xilinx ZynqMP DPDMA driver Laurent Pinchart ` (3 preceding siblings ...) 2020-05-28 2:52 ` [PATCH v5 4/6] dmaengine: xilinx: dpdma: Add the Xilinx DisplayPort DMA engine driver Laurent Pinchart @ 2020-05-28 2:52 ` Laurent Pinchart 2020-05-28 2:52 ` [PATCH v5 6/6] arm64: dts: zynqmp: Add DPDMA node Laurent Pinchart 2020-06-29 9:30 ` [PATCH v5 0/6] dma: Add Xilinx ZynqMP DPDMA driver Laurent Pinchart 6 siblings, 0 replies; 18+ messages in thread From: Laurent Pinchart @ 2020-05-28 2:52 UTC (permalink / raw) To: dmaengine Cc: Michal Simek, Hyun Kwon, Tejas Upadhyay, Satish Kumar Nagireddy, Vinod Koul, Peter Ujfalusi Expose statistics to debugfs when available. This helps debugging issues with the DPDMA driver. Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> --- Changes since v3: - Return -EFAULT instead of bytes remaining after copy_to_user() Changes since v2: - Refactor debugfs code --- drivers/dma/xilinx/xilinx_dpdma.c | 228 ++++++++++++++++++++++++++++++ 1 file changed, 228 insertions(+) diff --git a/drivers/dma/xilinx/xilinx_dpdma.c b/drivers/dma/xilinx/xilinx_dpdma.c index 227f8b083d1f..2491720e5c9d 100644 --- a/drivers/dma/xilinx/xilinx_dpdma.c +++ b/drivers/dma/xilinx/xilinx_dpdma.c @@ -10,6 +10,7 @@ #include <linux/bitfield.h> #include <linux/bits.h> #include <linux/clk.h> +#include <linux/debugfs.h> #include <linux/delay.h> #include <linux/dmaengine.h> #include <linux/dmapool.h> @@ -265,6 +266,229 @@ struct xilinx_dpdma_device { bool ext_addr; }; +/* ----------------------------------------------------------------------------- + * DebugFS + */ + +#ifdef CONFIG_DEBUG_FS + +#define XILINX_DPDMA_DEBUGFS_READ_MAX_SIZE 32 +#define XILINX_DPDMA_DEBUGFS_UINT16_MAX_STR "65535" + +/* Match xilinx_dpdma_testcases vs dpdma_debugfs_reqs[] entry */ +enum xilinx_dpdma_testcases { + DPDMA_TC_INTR_DONE, + DPDMA_TC_NONE +}; + +struct xilinx_dpdma_debugfs { + enum xilinx_dpdma_testcases testcase; + u16 xilinx_dpdma_irq_done_count; + unsigned int chan_id; +}; + +static struct xilinx_dpdma_debugfs dpdma_debugfs; +struct xilinx_dpdma_debugfs_request { + const char *name; + enum xilinx_dpdma_testcases tc; + ssize_t (*read)(char *buf); + int (*write)(char *args); +}; + +static void xilinx_dpdma_debugfs_desc_done_irq(struct xilinx_dpdma_chan *chan) +{ + if (chan->id == dpdma_debugfs.chan_id) + dpdma_debugfs.xilinx_dpdma_irq_done_count++; +} + +static ssize_t xilinx_dpdma_debugfs_desc_done_irq_read(char *buf) +{ + size_t out_str_len; + + dpdma_debugfs.testcase = DPDMA_TC_NONE; + + out_str_len = strlen(XILINX_DPDMA_DEBUGFS_UINT16_MAX_STR); + out_str_len = min_t(size_t, XILINX_DPDMA_DEBUGFS_READ_MAX_SIZE, + out_str_len); + snprintf(buf, out_str_len, "%d", + dpdma_debugfs.xilinx_dpdma_irq_done_count); + + return 0; +} + +static int xilinx_dpdma_debugfs_desc_done_irq_write(char *args) +{ + char *arg; + int ret; + u32 id; + + arg = strsep(&args, " "); + if (!arg || strncasecmp(arg, "start", 5)) + return -EINVAL; + + arg = strsep(&args, " "); + if (!arg) + return -EINVAL; + + ret = kstrtou32(arg, 0, &id); + if (ret < 0) + return ret; + + if (id < ZYNQMP_DPDMA_VIDEO0 || id > ZYNQMP_DPDMA_AUDIO1) + return -EINVAL; + + dpdma_debugfs.testcase = DPDMA_TC_INTR_DONE; + dpdma_debugfs.xilinx_dpdma_irq_done_count = 0; + dpdma_debugfs.chan_id = id; + + return 0; +} + +/* Match xilinx_dpdma_testcases vs dpdma_debugfs_reqs[] entry */ +struct xilinx_dpdma_debugfs_request dpdma_debugfs_reqs[] = { + { + .name = "DESCRIPTOR_DONE_INTR", + .tc = DPDMA_TC_INTR_DONE, + .read = xilinx_dpdma_debugfs_desc_done_irq_read, + .write = xilinx_dpdma_debugfs_desc_done_irq_write, + }, +}; + +static ssize_t xilinx_dpdma_debugfs_read(struct file *f, char __user *buf, + size_t size, loff_t *pos) +{ + enum xilinx_dpdma_testcases testcase; + char *kern_buff; + int ret = 0; + + if (*pos != 0 || size <= 0) + return -EINVAL; + + kern_buff = kzalloc(XILINX_DPDMA_DEBUGFS_READ_MAX_SIZE, GFP_KERNEL); + if (!kern_buff) { + dpdma_debugfs.testcase = DPDMA_TC_NONE; + return -ENOMEM; + } + + testcase = READ_ONCE(dpdma_debugfs.testcase); + if (testcase != DPDMA_TC_NONE) { + ret = dpdma_debugfs_reqs[testcase].read(kern_buff); + if (ret < 0) + goto done; + } else { + strlcpy(kern_buff, "No testcase executed", + XILINX_DPDMA_DEBUGFS_READ_MAX_SIZE); + } + + size = min(size, strlen(kern_buff)); + if (copy_to_user(buf, kern_buff, size)) + ret = -EFAULT; + +done: + kfree(kern_buff); + if (ret) + return ret; + + *pos = size + 1; + return size; +} + +static ssize_t xilinx_dpdma_debugfs_write(struct file *f, + const char __user *buf, size_t size, + loff_t *pos) +{ + char *kern_buff, *kern_buff_start; + char *testcase; + unsigned int i; + int ret; + + if (*pos != 0 || size <= 0) + return -EINVAL; + + /* Supporting single instance of test as of now. */ + if (dpdma_debugfs.testcase != DPDMA_TC_NONE) + return -EBUSY; + + kern_buff = kzalloc(size, GFP_KERNEL); + if (!kern_buff) + return -ENOMEM; + kern_buff_start = kern_buff; + + ret = strncpy_from_user(kern_buff, buf, size); + if (ret < 0) + goto done; + + /* Read the testcase name from a user request. */ + testcase = strsep(&kern_buff, " "); + + for (i = 0; i < ARRAY_SIZE(dpdma_debugfs_reqs); i++) { + if (!strcasecmp(testcase, dpdma_debugfs_reqs[i].name)) + break; + } + + if (i == ARRAY_SIZE(dpdma_debugfs_reqs)) { + ret = -EINVAL; + goto done; + } + + ret = dpdma_debugfs_reqs[i].write(kern_buff); + if (ret < 0) + goto done; + + ret = size; + +done: + kfree(kern_buff_start); + return ret; +} + +static const struct file_operations fops_xilinx_dpdma_dbgfs = { + .owner = THIS_MODULE, + .read = xilinx_dpdma_debugfs_read, + .write = xilinx_dpdma_debugfs_write, +}; + +static int xilinx_dpdma_debugfs_init(struct device *dev) +{ + int err; + struct dentry *xilinx_dpdma_debugfs_dir, *xilinx_dpdma_debugfs_file; + + dpdma_debugfs.testcase = DPDMA_TC_NONE; + + xilinx_dpdma_debugfs_dir = debugfs_create_dir("dpdma", NULL); + if (!xilinx_dpdma_debugfs_dir) { + dev_err(dev, "debugfs_create_dir failed\n"); + return -ENODEV; + } + + xilinx_dpdma_debugfs_file = + debugfs_create_file("testcase", 0444, + xilinx_dpdma_debugfs_dir, NULL, + &fops_xilinx_dpdma_dbgfs); + if (!xilinx_dpdma_debugfs_file) { + dev_err(dev, "debugfs_create_file testcase failed\n"); + err = -ENODEV; + goto err_dbgfs; + } + return 0; + +err_dbgfs: + debugfs_remove_recursive(xilinx_dpdma_debugfs_dir); + xilinx_dpdma_debugfs_dir = NULL; + return err; +} + +#else +static int xilinx_dpdma_debugfs_init(struct device *dev) +{ + return 0; +} + +static void xilinx_dpdma_debugfs_desc_done_irq(struct xilinx_dpdma_chan *chan) +{ +} +#endif /* CONFIG_DEBUG_FS */ + /* ----------------------------------------------------------------------------- * I/O Accessors */ @@ -850,6 +1074,8 @@ static void xilinx_dpdma_chan_done_irq(struct xilinx_dpdma_chan *chan) spin_lock_irqsave(&chan->lock, flags); + xilinx_dpdma_debugfs_desc_done_irq(chan); + if (active) vchan_cyclic_callback(&active->vdesc); else @@ -1496,6 +1722,8 @@ static int xilinx_dpdma_probe(struct platform_device *pdev) xilinx_dpdma_enable_irq(xdev); + xilinx_dpdma_debugfs_init(&pdev->dev); + dev_info(&pdev->dev, "Xilinx DPDMA engine is probed\n"); return 0; -- Regards, Laurent Pinchart ^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH v5 6/6] arm64: dts: zynqmp: Add DPDMA node 2020-05-28 2:52 [PATCH v5 0/6] dma: Add Xilinx ZynqMP DPDMA driver Laurent Pinchart ` (4 preceding siblings ...) 2020-05-28 2:52 ` [PATCH v5 5/6] dmaengine: xilinx: dpdma: Add debugfs support Laurent Pinchart @ 2020-05-28 2:52 ` Laurent Pinchart 2020-06-29 9:30 ` [PATCH v5 0/6] dma: Add Xilinx ZynqMP DPDMA driver Laurent Pinchart 6 siblings, 0 replies; 18+ messages in thread From: Laurent Pinchart @ 2020-05-28 2:52 UTC (permalink / raw) To: dmaengine Cc: Michal Simek, Hyun Kwon, Tejas Upadhyay, Satish Kumar Nagireddy, Vinod Koul, Peter Ujfalusi Add a DT node for the DisplayPort DMA engine (DPDMA). Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Michal Simek <michal.simek@xilinx.com> --- arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi | 4 ++++ arch/arm64/boot/dts/xilinx/zynqmp.dtsi | 10 ++++++++++ 2 files changed, 14 insertions(+) diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi index 9868ca15dfc5..32c4914738d9 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi +++ b/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi @@ -57,6 +57,10 @@ &cpu0 { clocks = <&zynqmp_clk ACPU>; }; +&dpdma { + clocks = <&zynqmp_clk DPDMA_REF>; +}; + &fpd_dma_chan1 { clocks = <&zynqmp_clk GDMA_REF>, <&zynqmp_clk LPD_LSBUS>; }; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi index 26d926eb1431..2e284eb8d3c1 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi +++ b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi @@ -246,6 +246,16 @@ pmu@9000 { }; }; + dpdma: dma-controller@fd4c0000 { + compatible = "xlnx,zynqmp-dpdma"; + status = "disabled"; + reg = <0x0 0xfd4c0000 0x0 0x1000>; + interrupts = <0 122 4>; + interrupt-parent = <&gic>; + clock-names = "axi_clk"; + #dma-cells = <1>; + }; + /* GDMA */ fpd_dma_chan1: dma@fd500000 { status = "disabled"; -- Regards, Laurent Pinchart ^ permalink raw reply related [flat|nested] 18+ messages in thread
* Re: [PATCH v5 0/6] dma: Add Xilinx ZynqMP DPDMA driver 2020-05-28 2:52 [PATCH v5 0/6] dma: Add Xilinx ZynqMP DPDMA driver Laurent Pinchart ` (5 preceding siblings ...) 2020-05-28 2:52 ` [PATCH v5 6/6] arm64: dts: zynqmp: Add DPDMA node Laurent Pinchart @ 2020-06-29 9:30 ` Laurent Pinchart 2020-06-29 9:56 ` Vinod Koul 6 siblings, 1 reply; 18+ messages in thread From: Laurent Pinchart @ 2020-06-29 9:30 UTC (permalink / raw) To: Vinod Koul Cc: dmaengine, Michal Simek, Hyun Kwon, Tejas Upadhyay, Satish Kumar Nagireddy, Peter Ujfalusi, Greg KH Hi Vinod, CC'ing Greg. The first version of this patch series I've posted dates back from early November last year. Could you please help getting it merged ? On Thu, May 28, 2020 at 05:52:22AM +0300, Laurent Pinchart wrote: > Hello, > > This patch series adds a new driver for the DPDMA engine found in the > Xilinx ZynqMP. > > The previous version can be found at [1]. All review comments have been > taken into account. The only change is the addition of the > DMA_PREP_LOAD_EOT transaction flag (and the corresponding DMA_LOAD_EOT > capability bit), as requested during the review of v4. Please see the > discussions from v4 for the rationale. > > The driver has been successfully tested with the ZynqMP DisplayPort > subsystem DRM driver. > > [1] https://lore.kernel.org/dmaengine/20200513165943.25120-1-laurent.pinchart@ideasonboard.com/ > > Hyun Kwon (1): > dmaengine: xilinx: dpdma: Add the Xilinx DisplayPort DMA engine driver > > Laurent Pinchart (5): > dt: bindings: dma: xilinx: dpdma: DT bindings for Xilinx DPDMA > dmaengine: virt-dma: Use lockdep to check locking requirements > dmaengine: Add support for repeating transactions > dmaengine: xilinx: dpdma: Add debugfs support > arm64: dts: zynqmp: Add DPDMA node > > .../dma/xilinx/xlnx,zynqmp-dpdma.yaml | 68 + > MAINTAINERS | 9 + > .../arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi | 4 + > arch/arm64/boot/dts/xilinx/zynqmp.dtsi | 10 + > drivers/dma/Kconfig | 10 + > drivers/dma/virt-dma.c | 2 + > drivers/dma/virt-dma.h | 10 + > drivers/dma/xilinx/Makefile | 1 + > drivers/dma/xilinx/xilinx_dpdma.c | 1782 +++++++++++++++++ > include/dt-bindings/dma/xlnx-zynqmp-dpdma.h | 16 + > include/linux/dmaengine.h | 19 + > 11 files changed, 1931 insertions(+) > create mode 100644 Documentation/devicetree/bindings/dma/xilinx/xlnx,zynqmp-dpdma.yaml > create mode 100644 drivers/dma/xilinx/xilinx_dpdma.c > create mode 100644 include/dt-bindings/dma/xlnx-zynqmp-dpdma.h -- Regards, Laurent Pinchart ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH v5 0/6] dma: Add Xilinx ZynqMP DPDMA driver 2020-06-29 9:30 ` [PATCH v5 0/6] dma: Add Xilinx ZynqMP DPDMA driver Laurent Pinchart @ 2020-06-29 9:56 ` Vinod Koul 2020-06-29 23:39 ` Laurent Pinchart 0 siblings, 1 reply; 18+ messages in thread From: Vinod Koul @ 2020-06-29 9:56 UTC (permalink / raw) To: Laurent Pinchart Cc: dmaengine, Michal Simek, Hyun Kwon, Tejas Upadhyay, Satish Kumar Nagireddy, Peter Ujfalusi, Greg KH Hi Laurent, On 29-06-20, 12:30, Laurent Pinchart wrote: > Hi Vinod, > > CC'ing Greg. > > The first version of this patch series I've posted dates back from early > November last year. Could you please help getting it merged ? Sorry for the delay in reviewing this series, this one is on my review list for this week, so I should get to this very soon. > > On Thu, May 28, 2020 at 05:52:22AM +0300, Laurent Pinchart wrote: > > Hello, > > > > This patch series adds a new driver for the DPDMA engine found in the > > Xilinx ZynqMP. > > > > The previous version can be found at [1]. All review comments have been > > taken into account. The only change is the addition of the > > DMA_PREP_LOAD_EOT transaction flag (and the corresponding DMA_LOAD_EOT > > capability bit), as requested during the review of v4. Please see the > > discussions from v4 for the rationale. > > > > The driver has been successfully tested with the ZynqMP DisplayPort > > subsystem DRM driver. > > > > [1] https://lore.kernel.org/dmaengine/20200513165943.25120-1-laurent.pinchart@ideasonboard.com/ > > > > Hyun Kwon (1): > > dmaengine: xilinx: dpdma: Add the Xilinx DisplayPort DMA engine driver > > > > Laurent Pinchart (5): > > dt: bindings: dma: xilinx: dpdma: DT bindings for Xilinx DPDMA > > dmaengine: virt-dma: Use lockdep to check locking requirements > > dmaengine: Add support for repeating transactions > > dmaengine: xilinx: dpdma: Add debugfs support > > arm64: dts: zynqmp: Add DPDMA node > > > > .../dma/xilinx/xlnx,zynqmp-dpdma.yaml | 68 + > > MAINTAINERS | 9 + > > .../arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi | 4 + > > arch/arm64/boot/dts/xilinx/zynqmp.dtsi | 10 + > > drivers/dma/Kconfig | 10 + > > drivers/dma/virt-dma.c | 2 + > > drivers/dma/virt-dma.h | 10 + > > drivers/dma/xilinx/Makefile | 1 + > > drivers/dma/xilinx/xilinx_dpdma.c | 1782 +++++++++++++++++ > > include/dt-bindings/dma/xlnx-zynqmp-dpdma.h | 16 + > > include/linux/dmaengine.h | 19 + > > 11 files changed, 1931 insertions(+) > > create mode 100644 Documentation/devicetree/bindings/dma/xilinx/xlnx,zynqmp-dpdma.yaml > > create mode 100644 drivers/dma/xilinx/xilinx_dpdma.c > > create mode 100644 include/dt-bindings/dma/xlnx-zynqmp-dpdma.h > > -- > Regards, > > Laurent Pinchart -- ~Vinod ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH v5 0/6] dma: Add Xilinx ZynqMP DPDMA driver 2020-06-29 9:56 ` Vinod Koul @ 2020-06-29 23:39 ` Laurent Pinchart 0 siblings, 0 replies; 18+ messages in thread From: Laurent Pinchart @ 2020-06-29 23:39 UTC (permalink / raw) To: Vinod Koul Cc: dmaengine, Michal Simek, Hyun Kwon, Tejas Upadhyay, Satish Kumar Nagireddy, Peter Ujfalusi, Greg KH Hi Vinod, On Mon, Jun 29, 2020 at 03:26:47PM +0530, Vinod Koul wrote: > On 29-06-20, 12:30, Laurent Pinchart wrote: > > Hi Vinod, > > > > CC'ing Greg. > > > > The first version of this patch series I've posted dates back from early > > November last year. Could you please help getting it merged ? > > Sorry for the delay in reviewing this series, this one is on my review > list for this week, so I should get to this very soon. Thank you. > > On Thu, May 28, 2020 at 05:52:22AM +0300, Laurent Pinchart wrote: > > > Hello, > > > > > > This patch series adds a new driver for the DPDMA engine found in the > > > Xilinx ZynqMP. > > > > > > The previous version can be found at [1]. All review comments have been > > > taken into account. The only change is the addition of the > > > DMA_PREP_LOAD_EOT transaction flag (and the corresponding DMA_LOAD_EOT > > > capability bit), as requested during the review of v4. Please see the > > > discussions from v4 for the rationale. > > > > > > The driver has been successfully tested with the ZynqMP DisplayPort > > > subsystem DRM driver. > > > > > > [1] https://lore.kernel.org/dmaengine/20200513165943.25120-1-laurent.pinchart@ideasonboard.com/ > > > > > > Hyun Kwon (1): > > > dmaengine: xilinx: dpdma: Add the Xilinx DisplayPort DMA engine driver > > > > > > Laurent Pinchart (5): > > > dt: bindings: dma: xilinx: dpdma: DT bindings for Xilinx DPDMA > > > dmaengine: virt-dma: Use lockdep to check locking requirements > > > dmaengine: Add support for repeating transactions > > > dmaengine: xilinx: dpdma: Add debugfs support > > > arm64: dts: zynqmp: Add DPDMA node > > > > > > .../dma/xilinx/xlnx,zynqmp-dpdma.yaml | 68 + > > > MAINTAINERS | 9 + > > > .../arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi | 4 + > > > arch/arm64/boot/dts/xilinx/zynqmp.dtsi | 10 + > > > drivers/dma/Kconfig | 10 + > > > drivers/dma/virt-dma.c | 2 + > > > drivers/dma/virt-dma.h | 10 + > > > drivers/dma/xilinx/Makefile | 1 + > > > drivers/dma/xilinx/xilinx_dpdma.c | 1782 +++++++++++++++++ > > > include/dt-bindings/dma/xlnx-zynqmp-dpdma.h | 16 + > > > include/linux/dmaengine.h | 19 + > > > 11 files changed, 1931 insertions(+) > > > create mode 100644 Documentation/devicetree/bindings/dma/xilinx/xlnx,zynqmp-dpdma.yaml > > > create mode 100644 drivers/dma/xilinx/xilinx_dpdma.c > > > create mode 100644 include/dt-bindings/dma/xlnx-zynqmp-dpdma.h -- Regards, Laurent Pinchart ^ permalink raw reply [flat|nested] 18+ messages in thread
end of thread, other threads:[~2020-07-08 20:19 UTC | newest] Thread overview: 18+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2020-05-28 2:52 [PATCH v5 0/6] dma: Add Xilinx ZynqMP DPDMA driver Laurent Pinchart 2020-05-28 2:52 ` [PATCH v5 1/6] dt: bindings: dma: xilinx: dpdma: DT bindings for Xilinx DPDMA Laurent Pinchart 2020-05-28 2:52 ` [PATCH v5 2/6] dmaengine: virt-dma: Use lockdep to check locking requirements Laurent Pinchart 2020-05-28 2:52 ` [PATCH v5 3/6] dmaengine: Add support for repeating transactions Laurent Pinchart 2020-07-03 17:10 ` Vinod Koul 2020-07-03 17:22 ` Laurent Pinchart 2020-07-03 17:37 ` Vinod Koul 2020-07-03 17:47 ` Laurent Pinchart 2020-07-03 17:54 ` Vinod Koul 2020-07-08 20:19 ` Laurent Pinchart 2020-05-28 2:52 ` [PATCH v5 4/6] dmaengine: xilinx: dpdma: Add the Xilinx DisplayPort DMA engine driver Laurent Pinchart 2020-07-03 17:32 ` Vinod Koul 2020-07-03 17:43 ` Laurent Pinchart 2020-05-28 2:52 ` [PATCH v5 5/6] dmaengine: xilinx: dpdma: Add debugfs support Laurent Pinchart 2020-05-28 2:52 ` [PATCH v5 6/6] arm64: dts: zynqmp: Add DPDMA node Laurent Pinchart 2020-06-29 9:30 ` [PATCH v5 0/6] dma: Add Xilinx ZynqMP DPDMA driver Laurent Pinchart 2020-06-29 9:56 ` Vinod Koul 2020-06-29 23:39 ` Laurent Pinchart
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).