From: Geert Uytterhoeven <geert+renesas@glider.be> To: "Rob Herring" <robh+dt@kernel.org>, "Laurent Pinchart" <laurent.pinchart+renesas@ideasonboard.com>, "Linus Walleij" <linus.walleij@linaro.org>, "Bartosz Golaszewski" <bgolaszewski@baylibre.com>, "Benoît Cousson" <bcousson@baylibre.com>, "Tony Lindgren" <tony@atomide.com>, "Jan Tuerk" <jan.tuerk@emtrion.com>, "Shawn Guo" <shawnguo@kernel.org> Cc: devicetree@vger.kernel.org, linux-gpio@vger.kernel.org, linux-omap@vger.kernel.org, linux-arm-kernel@lists.infradead.org, Geert Uytterhoeven <geert+renesas@glider.be> Subject: [PATCH 1/3] ARM: dts: dra7x-evm: Align GPIO hog names with dt-schema Date: Fri, 21 May 2021 09:54:06 +0200 [thread overview] Message-ID: <e8350ea542c92465020f03481d76943168df2935.1621583562.git.geert+renesas@glider.be> (raw) In-Reply-To: <cover.1621583562.git.geert+renesas@glider.be> The dt-schema for nxp,pcf8575 expects GPIO hogs node names to end with a 'hog' suffix. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> --- arch/arm/boot/dts/dra7-evm.dts | 2 +- arch/arm/boot/dts/dra71-evm.dts | 2 +- arch/arm/boot/dts/dra72-evm-common.dtsi | 2 +- arch/arm/boot/dts/dra76-evm.dts | 2 +- 4 files changed, 4 insertions(+), 4 deletions(-) diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts index 38530dbb89a00b7c..3dcb6e1f49bcf1f0 100644 --- a/arch/arm/boot/dts/dra7-evm.dts +++ b/arch/arm/boot/dts/dra7-evm.dts @@ -366,7 +366,7 @@ pcf_hdmi: gpio@26 { reg = <0x26>; gpio-controller; #gpio-cells = <2>; - p1 { + hdmi-audio-hog { /* vin6_sel_s0: high: VIN6, low: audio */ gpio-hog; gpios = <1 GPIO_ACTIVE_HIGH>; diff --git a/arch/arm/boot/dts/dra71-evm.dts b/arch/arm/boot/dts/dra71-evm.dts index 6d2cca6b44883e59..a64364443031525b 100644 --- a/arch/arm/boot/dts/dra71-evm.dts +++ b/arch/arm/boot/dts/dra71-evm.dts @@ -187,7 +187,7 @@ &pcf_gpio_21 { }; &pcf_hdmi { - p0 { + hdmi-i2c-disable-hog { /* * PM_OEn to High: Disable routing I2C3 to PM_I2C * With this PM_SEL(p3) should not matter diff --git a/arch/arm/boot/dts/dra72-evm-common.dtsi b/arch/arm/boot/dts/dra72-evm-common.dtsi index b65b2dd094d0ff57..f2384277d5dcdc5c 100644 --- a/arch/arm/boot/dts/dra72-evm-common.dtsi +++ b/arch/arm/boot/dts/dra72-evm-common.dtsi @@ -268,7 +268,7 @@ pcf_hdmi: pcf8575@26 { */ lines-initial-states = <0x0f2b>; - p1 { + hdmi-audio-hog { /* vin6_sel_s0: high: VIN6, low: audio */ gpio-hog; gpios = <1 GPIO_ACTIVE_HIGH>; diff --git a/arch/arm/boot/dts/dra76-evm.dts b/arch/arm/boot/dts/dra76-evm.dts index 9bd01ae40b1d1fbb..df47ea59c9c404c2 100644 --- a/arch/arm/boot/dts/dra76-evm.dts +++ b/arch/arm/boot/dts/dra76-evm.dts @@ -381,7 +381,7 @@ pcf_hdmi: pcf8575@26 { reg = <0x26>; gpio-controller; #gpio-cells = <2>; - p1 { + hdmi-audio-hog { /* vin6_sel_s0: high: VIN6, low: audio */ gpio-hog; gpios = <1 GPIO_ACTIVE_HIGH>; -- 2.25.1
WARNING: multiple messages have this Message-ID (diff)
From: Geert Uytterhoeven <geert+renesas@glider.be> To: "Rob Herring" <robh+dt@kernel.org>, "Laurent Pinchart" <laurent.pinchart+renesas@ideasonboard.com>, "Linus Walleij" <linus.walleij@linaro.org>, "Bartosz Golaszewski" <bgolaszewski@baylibre.com>, "Benoît Cousson" <bcousson@baylibre.com>, "Tony Lindgren" <tony@atomide.com>, "Jan Tuerk" <jan.tuerk@emtrion.com>, "Shawn Guo" <shawnguo@kernel.org> Cc: devicetree@vger.kernel.org, linux-gpio@vger.kernel.org, linux-omap@vger.kernel.org, linux-arm-kernel@lists.infradead.org, Geert Uytterhoeven <geert+renesas@glider.be> Subject: [PATCH 1/3] ARM: dts: dra7x-evm: Align GPIO hog names with dt-schema Date: Fri, 21 May 2021 09:54:06 +0200 [thread overview] Message-ID: <e8350ea542c92465020f03481d76943168df2935.1621583562.git.geert+renesas@glider.be> (raw) In-Reply-To: <cover.1621583562.git.geert+renesas@glider.be> The dt-schema for nxp,pcf8575 expects GPIO hogs node names to end with a 'hog' suffix. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> --- arch/arm/boot/dts/dra7-evm.dts | 2 +- arch/arm/boot/dts/dra71-evm.dts | 2 +- arch/arm/boot/dts/dra72-evm-common.dtsi | 2 +- arch/arm/boot/dts/dra76-evm.dts | 2 +- 4 files changed, 4 insertions(+), 4 deletions(-) diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts index 38530dbb89a00b7c..3dcb6e1f49bcf1f0 100644 --- a/arch/arm/boot/dts/dra7-evm.dts +++ b/arch/arm/boot/dts/dra7-evm.dts @@ -366,7 +366,7 @@ pcf_hdmi: gpio@26 { reg = <0x26>; gpio-controller; #gpio-cells = <2>; - p1 { + hdmi-audio-hog { /* vin6_sel_s0: high: VIN6, low: audio */ gpio-hog; gpios = <1 GPIO_ACTIVE_HIGH>; diff --git a/arch/arm/boot/dts/dra71-evm.dts b/arch/arm/boot/dts/dra71-evm.dts index 6d2cca6b44883e59..a64364443031525b 100644 --- a/arch/arm/boot/dts/dra71-evm.dts +++ b/arch/arm/boot/dts/dra71-evm.dts @@ -187,7 +187,7 @@ &pcf_gpio_21 { }; &pcf_hdmi { - p0 { + hdmi-i2c-disable-hog { /* * PM_OEn to High: Disable routing I2C3 to PM_I2C * With this PM_SEL(p3) should not matter diff --git a/arch/arm/boot/dts/dra72-evm-common.dtsi b/arch/arm/boot/dts/dra72-evm-common.dtsi index b65b2dd094d0ff57..f2384277d5dcdc5c 100644 --- a/arch/arm/boot/dts/dra72-evm-common.dtsi +++ b/arch/arm/boot/dts/dra72-evm-common.dtsi @@ -268,7 +268,7 @@ pcf_hdmi: pcf8575@26 { */ lines-initial-states = <0x0f2b>; - p1 { + hdmi-audio-hog { /* vin6_sel_s0: high: VIN6, low: audio */ gpio-hog; gpios = <1 GPIO_ACTIVE_HIGH>; diff --git a/arch/arm/boot/dts/dra76-evm.dts b/arch/arm/boot/dts/dra76-evm.dts index 9bd01ae40b1d1fbb..df47ea59c9c404c2 100644 --- a/arch/arm/boot/dts/dra76-evm.dts +++ b/arch/arm/boot/dts/dra76-evm.dts @@ -381,7 +381,7 @@ pcf_hdmi: pcf8575@26 { reg = <0x26>; gpio-controller; #gpio-cells = <2>; - p1 { + hdmi-audio-hog { /* vin6_sel_s0: high: VIN6, low: audio */ gpio-hog; gpios = <1 GPIO_ACTIVE_HIGH>; -- 2.25.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2021-05-21 7:54 UTC|newest] Thread overview: 28+ messages / expand[flat|nested] mbox.gz Atom feed top 2021-05-21 7:54 [PATCH 0/3] pcf857x: DTS fixes and DT binding to json-schema conversion Geert Uytterhoeven 2021-05-21 7:54 ` Geert Uytterhoeven 2021-05-21 7:54 ` Geert Uytterhoeven [this message] 2021-05-21 7:54 ` [PATCH 1/3] ARM: dts: dra7x-evm: Align GPIO hog names with dt-schema Geert Uytterhoeven 2021-05-23 1:54 ` Laurent Pinchart 2021-05-23 1:54 ` Laurent Pinchart 2021-05-27 12:02 ` Tony Lindgren 2021-05-27 12:02 ` Tony Lindgren 2021-05-21 7:54 ` [PATCH 2/3] ARM: dts: imx: emcon-avari: Fix nxp,pca8574 #gpio-cells Geert Uytterhoeven 2021-05-21 7:54 ` Geert Uytterhoeven 2021-05-23 1:55 ` Laurent Pinchart 2021-05-23 1:55 ` Laurent Pinchart 2021-05-23 5:42 ` Shawn Guo 2021-05-23 5:42 ` Shawn Guo 2021-05-21 7:54 ` [PATCH 3/3] dt-bindings: gpio: pcf857x: Convert to json-schema Geert Uytterhoeven 2021-05-21 7:54 ` Geert Uytterhoeven 2021-05-21 10:04 ` Linus Walleij 2021-05-21 10:04 ` Linus Walleij 2021-05-21 10:23 ` Geert Uytterhoeven 2021-05-21 10:23 ` Geert Uytterhoeven 2021-05-21 18:24 ` Rob Herring 2021-05-21 18:24 ` Rob Herring 2021-05-27 15:04 ` Geert Uytterhoeven 2021-05-27 15:04 ` Geert Uytterhoeven 2021-05-23 1:52 ` Laurent Pinchart 2021-05-23 1:52 ` Laurent Pinchart 2021-05-27 14:43 ` Geert Uytterhoeven 2021-05-27 14:43 ` Geert Uytterhoeven
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=e8350ea542c92465020f03481d76943168df2935.1621583562.git.geert+renesas@glider.be \ --to=geert+renesas@glider.be \ --cc=bcousson@baylibre.com \ --cc=bgolaszewski@baylibre.com \ --cc=devicetree@vger.kernel.org \ --cc=jan.tuerk@emtrion.com \ --cc=laurent.pinchart+renesas@ideasonboard.com \ --cc=linus.walleij@linaro.org \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-gpio@vger.kernel.org \ --cc=linux-omap@vger.kernel.org \ --cc=robh+dt@kernel.org \ --cc=shawnguo@kernel.org \ --cc=tony@atomide.com \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.