* [PATCH V5 0/5] Add minimal boot support for IPQ6018 @ 2020-01-16 7:44 Sricharan R 2020-01-16 7:44 ` [PATCH V5 1/5] dt-bindings: pinctrl: qcom: Add ipq6018 pinctrl bindings Sricharan R ` (4 more replies) 0 siblings, 5 replies; 8+ messages in thread From: Sricharan R @ 2020-01-16 7:44 UTC (permalink / raw) To: agross, devicetree, linus.walleij, linux-arm-kernel, linux-arm-msm, linux-gpio, linux-kernel, linux-soc, robh+dt, sivaprak, sricharan The IPQ6018 is Qualcomm\u2019s 802.11ax SoC for Routers, Gateways and Access Points. This series adds minimal board boot support for ipq6018-cp01 board. [V5] * Addressed review comments in pinctrl bindings from Rob. * Ran make dt_binding_check with modified patch. * Added fixed rate clocks in gcc clock controller node. * Patch 4 arm64: dts: Add ipq6018 SoC and CP01 board support has build dependency with, https://lkml.org/lkml/2020/1/9/84 [v4] * Addressed review comments in pinctrl bindings from Rob. * Ran make dt_binding_check and no issues was reported. * Deleted absahu email id from patch 4, since its bouncing now. * Patch 4 arm64: dts: Add ipq6018 SoC and CP01 board support has build dependency with, https://lkml.org/lkml/2020/1/9/84 [V3] * Removed clock driver and bindings from this patch series, and added them as a different series. * Removed qpic_padN from pinctrl driver. * Addressed review comments in dts, and added the remaining fixed clocks their * Fixed review comments in pinctrl bindings [v2] * Splitted dt bindings and driver into different patches. Added missing bindings and some style changes. * Added ipq6018 schema * Addressed review comments for gcc clock bindings. * Removed all clk critical flags, removed 1/1 factor clocks, moved to new way of specifying clk parents, and addressed other review comments. * Sorted nodes based on address, name, label. Removed unused clock nodes, Addressed other review comments. Sricharan R (5): dt-bindings: pinctrl: qcom: Add ipq6018 pinctrl bindings pinctrl: qcom: Add ipq6018 pinctrl driver dt-bindings: qcom: Add ipq6018 bindings arm64: dts: Add ipq6018 SoC and CP01 board support arm64: defconfig: Enable qcom ipq6018 clock and pinctrl Documentation/devicetree/bindings/arm/qcom.yaml | 8 + .../bindings/pinctrl/qcom,ipq6018-pinctrl.yaml | 174 +++ arch/arm64/boot/dts/qcom/Makefile | 1 + arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts | 30 + arch/arm64/boot/dts/qcom/ipq6018.dtsi | 263 +++++ arch/arm64/configs/defconfig | 3 + drivers/pinctrl/qcom/Kconfig | 10 + drivers/pinctrl/qcom/Makefile | 1 + drivers/pinctrl/qcom/pinctrl-ipq6018.c | 1107 ++++++++++++++++++++ 9 files changed, 1597 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml create mode 100644 arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts create mode 100644 arch/arm64/boot/dts/qcom/ipq6018.dtsi create mode 100644 drivers/pinctrl/qcom/pinctrl-ipq6018.c -- 1.9.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH V5 1/5] dt-bindings: pinctrl: qcom: Add ipq6018 pinctrl bindings 2020-01-16 7:44 [PATCH V5 0/5] Add minimal boot support for IPQ6018 Sricharan R @ 2020-01-16 7:44 ` Sricharan R 2020-01-17 16:01 ` Rob Herring 2020-01-16 7:44 ` [PATCH V5 2/5] pinctrl: qcom: Add ipq6018 pinctrl driver Sricharan R ` (3 subsequent siblings) 4 siblings, 1 reply; 8+ messages in thread From: Sricharan R @ 2020-01-16 7:44 UTC (permalink / raw) To: agross, devicetree, linus.walleij, linux-arm-kernel, linux-arm-msm, linux-gpio, linux-kernel, linux-soc, robh+dt, sivaprak, sricharan Cc: Selvam Sathappan Periakaruppan, Rajkumar Ayyasamy Add device tree binding Documentation details for ipq6018 pinctrl driver. Co-developed-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org> Signed-off-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org> Co-developed-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org> Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org> Co-developed-by: Sivaprakash Murugesan <sivaprak@codeaurora.org> Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org> Signed-off-by: Sricharan R <sricharan@codeaurora.org> --- [V5] * Addressed review comments from Rob * Ran dt bindings check and no errors were reported .../bindings/pinctrl/qcom,ipq6018-pinctrl.yaml | 162 +++++++++++++++++++++ 1 file changed, 162 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml new file mode 100644 index 0000000..0622258 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml @@ -0,0 +1,162 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/qcom,ipq6018-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Technologies, Inc. IPQ6018 TLMM block + +maintainers: + - Sricharan R <sricharan@codeaurora.org> + +description: | + This binding describes the Top Level Mode Multiplexer block found in the + IPQ6018 platform. + +properties: + compatible: + const: qcom,ipq6018-pinctrl + + reg: + maxItems: 1 + + interrupts: + description: Specifies the TLMM summary IRQ + maxItems: 1 + + interrupt-controller: true + + '#interrupt-cells': + description: + Specifies the PIN numbers and Flags, as defined in defined in + include/dt-bindings/interrupt-controller/irq.h + const: 2 + + gpio-controller: true + + '#gpio-cells': + description: Specifying the pin number and flags, as defined in + include/dt-bindings/gpio/gpio.h + const: 2 + + gpio-ranges: + description: Documentation/devicetree/bindings/gpio/gpio.txt + maxItems: 1 + +#PIN CONFIGURATION NODES +patternProperties: + '.*-pin.*': + type: object + description: + Pinctrl node's client devices use subnodes for desired pin configuration. + Client device subnodes use below standard properties. + allOf: + - $ref: "/schemas/pinctrl/pincfg-node.yaml" + + properties: + pins: + description: + List of gpio pins affected by the properties specified in this + subnode. The valid values are gpio1-80, sdc1_clk, sdc1_cmd, + sdc1_data, sdc2_clk, sdc2_cmd, sdc2_data, qdsd_cmd, qdsd_data0, + qdsd_data1, qdsd_data2, qdsd_data3 + minItems: 1 + maxItems: 4 + + function: + description: + Specify the alternative function to be configured for the specified + pins. + enum: [ adsp_ext, alsp_int, atest_bbrx0, atest_bbrx1, atest_char, + atest_char0, atest_char1, atest_char2, atest_char3, atest_combodac, + atest_gpsadc0, atest_gpsadc1, atest_tsens, atest_wlan0, + atest_wlan1, backlight_en, bimc_dte0, bimc_dte1, blsp1_i2c, + blsp2_i2c, blsp3_i2c, blsp4_i2c, blsp5_i2c, blsp6_i2c, blsp1_spi, + blsp1_spi_cs1, blsp1_spi_cs2, blsp1_spi_cs3, blsp2_spi, + blsp2_spi_cs1, blsp2_spi_cs2, blsp2_spi_cs3, blsp3_spi, + blsp3_spi_cs1, blsp3_spi_cs2, blsp3_spi_cs3, blsp4_spi, blsp5_spi, + blsp6_spi, blsp1_uart, blsp2_uart, blsp1_uim, blsp2_uim, cam1_rst, + cam1_standby, cam_mclk0, cam_mclk1, cci_async, cci_i2c, cci_timer0, + cci_timer1, cci_timer2, cdc_pdm0, codec_mad, dbg_out, display_5v, + dmic0_clk, dmic0_data, dsi_rst, ebi0_wrcdc, euro_us, ext_lpass, + flash_strobe, gcc_gp1_clk_a, gcc_gp1_clk_b, gcc_gp2_clk_a, + gcc_gp2_clk_b, gcc_gp3_clk_a, gcc_gp3_clk_b, gpio, gsm0_tx0, + gsm0_tx1, gsm1_tx0, gsm1_tx1, gyro_accl, kpsns0, kpsns1, kpsns2, + ldo_en, ldo_update, mag_int, mdp_vsync, modem_tsync, m_voc, + nav_pps, nav_tsync, pa_indicator, pbs0, pbs1, pbs2, pri_mi2s, + pri_mi2s_ws, prng_rosc, pwr_crypto_enabled_a, pwr_crypto_enabled_b, + pwr_modem_enabled_a, pwr_modem_enabled_b, pwr_nav_enabled_a, + pwr_nav_enabled_b, qdss_ctitrig_in_a0, qdss_ctitrig_in_a1, + qdss_ctitrig_in_b0, qdss_ctitrig_in_b1, qdss_ctitrig_out_a0, + qdss_ctitrig_out_a1, qdss_ctitrig_out_b0, qdss_ctitrig_out_b1, + qdss_traceclk_a, qdss_traceclk_b, qdss_tracectl_a, qdss_tracectl_b, + qdss_tracedata_a, qdss_tracedata_b, reset_n, sd_card, sd_write, + sec_mi2s, smb_int, ssbi_wtr0, ssbi_wtr1, uim1, uim2, uim3, + uim_batt, wcss_bt, wcss_fm, wcss_wlan, webcam1_rst ] + + drive-strength: + enum: [2, 4, 6, 8, 10, 12, 14, 16] + default: 2 + description: + Selects the drive strength for the specified pins, in mA. + + bias-pull-down: + type: boolean + description: The specified pin should be configured as pull down. + + bias-pull-up: + type: boolean + description: The specified pin should be configured as pull up. + + bias-disable: + type: boolean + description: The specified pin should be configured as no pull. + + output-high: + type: boolean + description: The specified pin is configured in output mode, driven + high. + + output-low: + type: boolean + description: The specified pin is configured in output mode, driven + low. + + required: + - pins + - function + + additionalProperties: false + +required: + - compatible + - reg + - interrupts + - interrupt-controller + - '#interrupt-cells' + - gpio-controller + - '#gpio-cells' + - gpio-ranges + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + tlmm: pinctrl@1000000 { + compatible = "qcom,ipq6018-pinctrl"; + reg = <0x01000000 0x300000>; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&tlmm 0 80>; + + serial3-pinmux { + pins = "gpio44", "gpio45"; + function = "blsp2_uart"; + drive-strength = <8>; + bias-pull-down; + }; + }; -- 2.7.4 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 8+ messages in thread
* Re: [PATCH V5 1/5] dt-bindings: pinctrl: qcom: Add ipq6018 pinctrl bindings 2020-01-16 7:44 ` [PATCH V5 1/5] dt-bindings: pinctrl: qcom: Add ipq6018 pinctrl bindings Sricharan R @ 2020-01-17 16:01 ` Rob Herring 2020-01-19 13:15 ` Sricharan R 0 siblings, 1 reply; 8+ messages in thread From: Rob Herring @ 2020-01-17 16:01 UTC (permalink / raw) To: Sricharan R Cc: devicetree, Rajkumar Ayyasamy, linux-arm-msm, linus.walleij, linux-kernel, Selvam Sathappan Periakaruppan, linux-gpio, agross, sivaprak, linux-soc, linux-arm-kernel On Thu, Jan 16, 2020 at 01:14:57PM +0530, Sricharan R wrote: > Add device tree binding Documentation details for ipq6018 > pinctrl driver. > > Co-developed-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org> > Signed-off-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org> > Co-developed-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org> > Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org> > Co-developed-by: Sivaprakash Murugesan <sivaprak@codeaurora.org> > Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org> > Signed-off-by: Sricharan R <sricharan@codeaurora.org> > --- > [V5] > * Addressed review comments from Rob > * Ran dt bindings check and no errors were reported > .../bindings/pinctrl/qcom,ipq6018-pinctrl.yaml | 162 +++++++++++++++++++++ > 1 file changed, 162 insertions(+) > create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml > > diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml > new file mode 100644 > index 0000000..0622258 > --- /dev/null > +++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml > @@ -0,0 +1,162 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/pinctrl/qcom,ipq6018-pinctrl.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Qualcomm Technologies, Inc. IPQ6018 TLMM block > + > +maintainers: > + - Sricharan R <sricharan@codeaurora.org> > + > +description: | > + This binding describes the Top Level Mode Multiplexer block found in the > + IPQ6018 platform. > + > +properties: > + compatible: > + const: qcom,ipq6018-pinctrl > + > + reg: > + maxItems: 1 > + > + interrupts: > + description: Specifies the TLMM summary IRQ > + maxItems: 1 > + > + interrupt-controller: true > + > + '#interrupt-cells': > + description: > + Specifies the PIN numbers and Flags, as defined in defined in > + include/dt-bindings/interrupt-controller/irq.h > + const: 2 > + > + gpio-controller: true > + > + '#gpio-cells': > + description: Specifying the pin number and flags, as defined in > + include/dt-bindings/gpio/gpio.h > + const: 2 > + > + gpio-ranges: > + description: Documentation/devicetree/bindings/gpio/gpio.txt You can drop the description. Nothing here specific to this binding. > + maxItems: 1 > + > +#PIN CONFIGURATION NODES > +patternProperties: > + '.*-pin.*': Ideally, this would be a bit more constrained. Such as '-pin$' or '-pinmux$'. Note that '-pin' is equivalent to what you have. > + type: object > + description: > + Pinctrl node's client devices use subnodes for desired pin configuration. > + Client device subnodes use below standard properties. > + allOf: > + - $ref: "/schemas/pinctrl/pincfg-node.yaml" > + > + properties: > + pins: > + description: > + List of gpio pins affected by the properties specified in this > + subnode. The valid values are gpio1-80, sdc1_clk, sdc1_cmd, > + sdc1_data, sdc2_clk, sdc2_cmd, sdc2_data, qdsd_cmd, qdsd_data0, > + qdsd_data1, qdsd_data2, qdsd_data3 Looks like constraints: items: oneOf: - pattern: "^gpio([1-9]|[1-7][0-9]|80)$" - enum: [ sdc1_clk, sdc1_cmd, ... ] > + minItems: 1 > + maxItems: 4 > + > + function: > + description: > + Specify the alternative function to be configured for the specified > + pins. > + enum: [ adsp_ext, alsp_int, atest_bbrx0, atest_bbrx1, atest_char, > + atest_char0, atest_char1, atest_char2, atest_char3, atest_combodac, > + atest_gpsadc0, atest_gpsadc1, atest_tsens, atest_wlan0, > + atest_wlan1, backlight_en, bimc_dte0, bimc_dte1, blsp1_i2c, > + blsp2_i2c, blsp3_i2c, blsp4_i2c, blsp5_i2c, blsp6_i2c, blsp1_spi, > + blsp1_spi_cs1, blsp1_spi_cs2, blsp1_spi_cs3, blsp2_spi, > + blsp2_spi_cs1, blsp2_spi_cs2, blsp2_spi_cs3, blsp3_spi, > + blsp3_spi_cs1, blsp3_spi_cs2, blsp3_spi_cs3, blsp4_spi, blsp5_spi, > + blsp6_spi, blsp1_uart, blsp2_uart, blsp1_uim, blsp2_uim, cam1_rst, > + cam1_standby, cam_mclk0, cam_mclk1, cci_async, cci_i2c, cci_timer0, > + cci_timer1, cci_timer2, cdc_pdm0, codec_mad, dbg_out, display_5v, > + dmic0_clk, dmic0_data, dsi_rst, ebi0_wrcdc, euro_us, ext_lpass, > + flash_strobe, gcc_gp1_clk_a, gcc_gp1_clk_b, gcc_gp2_clk_a, > + gcc_gp2_clk_b, gcc_gp3_clk_a, gcc_gp3_clk_b, gpio, gsm0_tx0, > + gsm0_tx1, gsm1_tx0, gsm1_tx1, gyro_accl, kpsns0, kpsns1, kpsns2, > + ldo_en, ldo_update, mag_int, mdp_vsync, modem_tsync, m_voc, > + nav_pps, nav_tsync, pa_indicator, pbs0, pbs1, pbs2, pri_mi2s, > + pri_mi2s_ws, prng_rosc, pwr_crypto_enabled_a, pwr_crypto_enabled_b, > + pwr_modem_enabled_a, pwr_modem_enabled_b, pwr_nav_enabled_a, > + pwr_nav_enabled_b, qdss_ctitrig_in_a0, qdss_ctitrig_in_a1, > + qdss_ctitrig_in_b0, qdss_ctitrig_in_b1, qdss_ctitrig_out_a0, > + qdss_ctitrig_out_a1, qdss_ctitrig_out_b0, qdss_ctitrig_out_b1, > + qdss_traceclk_a, qdss_traceclk_b, qdss_tracectl_a, qdss_tracectl_b, > + qdss_tracedata_a, qdss_tracedata_b, reset_n, sd_card, sd_write, > + sec_mi2s, smb_int, ssbi_wtr0, ssbi_wtr1, uim1, uim2, uim3, > + uim_batt, wcss_bt, wcss_fm, wcss_wlan, webcam1_rst ] > + > + drive-strength: > + enum: [2, 4, 6, 8, 10, 12, 14, 16] > + default: 2 > + description: > + Selects the drive strength for the specified pins, in mA. > + > + bias-pull-down: > + type: boolean > + description: The specified pin should be configured as pull down. > + > + bias-pull-up: > + type: boolean > + description: The specified pin should be configured as pull up. > + > + bias-disable: > + type: boolean > + description: The specified pin should be configured as no pull. > + > + output-high: > + type: boolean > + description: The specified pin is configured in output mode, driven > + high. > + > + output-low: > + type: boolean > + description: The specified pin is configured in output mode, driven > + low. No need to redefine the type and description on these 5 properties. Just a value of 'true' is enough. > + > + required: > + - pins > + - function > + > + additionalProperties: false > + > +required: > + - compatible > + - reg > + - interrupts > + - interrupt-controller > + - '#interrupt-cells' > + - gpio-controller > + - '#gpio-cells' > + - gpio-ranges > + > +additionalProperties: false > + > +examples: > + - | > + #include <dt-bindings/interrupt-controller/arm-gic.h> > + tlmm: pinctrl@1000000 { > + compatible = "qcom,ipq6018-pinctrl"; > + reg = <0x01000000 0x300000>; > + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-controller; > + #interrupt-cells = <2>; > + gpio-controller; > + #gpio-cells = <2>; > + gpio-ranges = <&tlmm 0 80>; > + > + serial3-pinmux { > + pins = "gpio44", "gpio45"; > + function = "blsp2_uart"; > + drive-strength = <8>; > + bias-pull-down; > + }; > + }; > -- > 2.7.4 > _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH V5 1/5] dt-bindings: pinctrl: qcom: Add ipq6018 pinctrl bindings 2020-01-17 16:01 ` Rob Herring @ 2020-01-19 13:15 ` Sricharan R 0 siblings, 0 replies; 8+ messages in thread From: Sricharan R @ 2020-01-19 13:15 UTC (permalink / raw) To: Rob Herring Cc: devicetree, Rajkumar Ayyasamy, linux-arm-msm, linus.walleij, linux-kernel, Selvam Sathappan Periakaruppan, linux-gpio, agross, sivaprak, linux-soc, linux-arm-kernel Hi Rob, Thanks for the review. On 1/17/2020 9:31 PM, Rob Herring wrote: > On Thu, Jan 16, 2020 at 01:14:57PM +0530, Sricharan R wrote: >> Add device tree binding Documentation details for ipq6018 >> pinctrl driver. >> >> Co-developed-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org> >> Signed-off-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org> >> Co-developed-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org> >> Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org> >> Co-developed-by: Sivaprakash Murugesan <sivaprak@codeaurora.org> >> Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org> >> Signed-off-by: Sricharan R <sricharan@codeaurora.org> >> --- >> [V5] >> * Addressed review comments from Rob >> * Ran dt bindings check and no errors were reported >> .../bindings/pinctrl/qcom,ipq6018-pinctrl.yaml | 162 +++++++++++++++++++++ >> 1 file changed, 162 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml >> >> diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml >> new file mode 100644 >> index 0000000..0622258 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml >> @@ -0,0 +1,162 @@ >> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) >> +%YAML 1.2 >> +--- >> +$id: http://devicetree.org/schemas/pinctrl/qcom,ipq6018-pinctrl.yaml# >> +$schema: http://devicetree.org/meta-schemas/core.yaml# >> + >> +title: Qualcomm Technologies, Inc. IPQ6018 TLMM block >> + >> +maintainers: >> + - Sricharan R <sricharan@codeaurora.org> >> + >> +description: | >> + This binding describes the Top Level Mode Multiplexer block found in the >> + IPQ6018 platform. >> + >> +properties: >> + compatible: >> + const: qcom,ipq6018-pinctrl >> + >> + reg: >> + maxItems: 1 >> + >> + interrupts: >> + description: Specifies the TLMM summary IRQ >> + maxItems: 1 >> + >> + interrupt-controller: true >> + >> + '#interrupt-cells': >> + description: >> + Specifies the PIN numbers and Flags, as defined in defined in >> + include/dt-bindings/interrupt-controller/irq.h >> + const: 2 >> + >> + gpio-controller: true >> + >> + '#gpio-cells': >> + description: Specifying the pin number and flags, as defined in >> + include/dt-bindings/gpio/gpio.h >> + const: 2 >> + >> + gpio-ranges: >> + description: Documentation/devicetree/bindings/gpio/gpio.txt > > You can drop the description. Nothing here specific to this binding. > ok. >> + maxItems: 1 >> + >> +#PIN CONFIGURATION NODES >> +patternProperties: >> + '.*-pin.*': > > Ideally, this would be a bit more constrained. Such as '-pin$' or > '-pinmux$'. > > Note that '-pin' is equivalent to what you have. > ok. >> + type: object >> + description: >> + Pinctrl node's client devices use subnodes for desired pin configuration. >> + Client device subnodes use below standard properties. >> + allOf: >> + - $ref: "/schemas/pinctrl/pincfg-node.yaml" >> + >> + properties: >> + pins: >> + description: >> + List of gpio pins affected by the properties specified in this >> + subnode. The valid values are gpio1-80, sdc1_clk, sdc1_cmd, >> + sdc1_data, sdc2_clk, sdc2_cmd, sdc2_data, qdsd_cmd, qdsd_data0, >> + qdsd_data1, qdsd_data2, qdsd_data3 > > Looks like constraints: > > items: > oneOf: > - pattern: "^gpio([1-9]|[1-7][0-9]|80)$" > - enum: [ sdc1_clk, sdc1_cmd, ... ] > ok. >> + minItems: 1 >> + maxItems: 4 >> + >> + function: >> + description: >> + Specify the alternative function to be configured for the specified >> + pins. >> + enum: [ adsp_ext, alsp_int, atest_bbrx0, atest_bbrx1, atest_char, >> + atest_char0, atest_char1, atest_char2, atest_char3, atest_combodac, >> + atest_gpsadc0, atest_gpsadc1, atest_tsens, atest_wlan0, >> + atest_wlan1, backlight_en, bimc_dte0, bimc_dte1, blsp1_i2c, >> + blsp2_i2c, blsp3_i2c, blsp4_i2c, blsp5_i2c, blsp6_i2c, blsp1_spi, >> + blsp1_spi_cs1, blsp1_spi_cs2, blsp1_spi_cs3, blsp2_spi, >> + blsp2_spi_cs1, blsp2_spi_cs2, blsp2_spi_cs3, blsp3_spi, >> + blsp3_spi_cs1, blsp3_spi_cs2, blsp3_spi_cs3, blsp4_spi, blsp5_spi, >> + blsp6_spi, blsp1_uart, blsp2_uart, blsp1_uim, blsp2_uim, cam1_rst, >> + cam1_standby, cam_mclk0, cam_mclk1, cci_async, cci_i2c, cci_timer0, >> + cci_timer1, cci_timer2, cdc_pdm0, codec_mad, dbg_out, display_5v, >> + dmic0_clk, dmic0_data, dsi_rst, ebi0_wrcdc, euro_us, ext_lpass, >> + flash_strobe, gcc_gp1_clk_a, gcc_gp1_clk_b, gcc_gp2_clk_a, >> + gcc_gp2_clk_b, gcc_gp3_clk_a, gcc_gp3_clk_b, gpio, gsm0_tx0, >> + gsm0_tx1, gsm1_tx0, gsm1_tx1, gyro_accl, kpsns0, kpsns1, kpsns2, >> + ldo_en, ldo_update, mag_int, mdp_vsync, modem_tsync, m_voc, >> + nav_pps, nav_tsync, pa_indicator, pbs0, pbs1, pbs2, pri_mi2s, >> + pri_mi2s_ws, prng_rosc, pwr_crypto_enabled_a, pwr_crypto_enabled_b, >> + pwr_modem_enabled_a, pwr_modem_enabled_b, pwr_nav_enabled_a, >> + pwr_nav_enabled_b, qdss_ctitrig_in_a0, qdss_ctitrig_in_a1, >> + qdss_ctitrig_in_b0, qdss_ctitrig_in_b1, qdss_ctitrig_out_a0, >> + qdss_ctitrig_out_a1, qdss_ctitrig_out_b0, qdss_ctitrig_out_b1, >> + qdss_traceclk_a, qdss_traceclk_b, qdss_tracectl_a, qdss_tracectl_b, >> + qdss_tracedata_a, qdss_tracedata_b, reset_n, sd_card, sd_write, >> + sec_mi2s, smb_int, ssbi_wtr0, ssbi_wtr1, uim1, uim2, uim3, >> + uim_batt, wcss_bt, wcss_fm, wcss_wlan, webcam1_rst ] >> + >> + drive-strength: >> + enum: [2, 4, 6, 8, 10, 12, 14, 16] >> + default: 2 >> + description: >> + Selects the drive strength for the specified pins, in mA. > >> + >> + bias-pull-down: >> + type: boolean >> + description: The specified pin should be configured as pull down. >> + >> + bias-pull-up: >> + type: boolean >> + description: The specified pin should be configured as pull up. >> + >> + bias-disable: >> + type: boolean >> + description: The specified pin should be configured as no pull. >> + >> + output-high: >> + type: boolean >> + description: The specified pin is configured in output mode, driven >> + high. >> + >> + output-low: >> + type: boolean >> + description: The specified pin is configured in output mode, driven >> + low. > > No need to redefine the type and description on these 5 properties. Just > a value of 'true' is enough. > ok. Regards, Sricharan -- "QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH V5 2/5] pinctrl: qcom: Add ipq6018 pinctrl driver 2020-01-16 7:44 [PATCH V5 0/5] Add minimal boot support for IPQ6018 Sricharan R 2020-01-16 7:44 ` [PATCH V5 1/5] dt-bindings: pinctrl: qcom: Add ipq6018 pinctrl bindings Sricharan R @ 2020-01-16 7:44 ` Sricharan R 2020-01-16 7:44 ` [PATCH V5 3/5] dt-bindings: qcom: Add ipq6018 bindings Sricharan R ` (2 subsequent siblings) 4 siblings, 0 replies; 8+ messages in thread From: Sricharan R @ 2020-01-16 7:44 UTC (permalink / raw) To: agross, devicetree, linus.walleij, linux-arm-kernel, linux-arm-msm, linux-gpio, linux-kernel, linux-soc, robh+dt, sivaprak, sricharan Cc: Selvam Sathappan Periakaruppan, Rajkumar Ayyasamy Add initial pinctrl driver to support pin configuration with pinctrl framework for ipq6018. Co-developed-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org> Signed-off-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org> Co-developed-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org> Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org> Co-developed-by: Sivaprakash Murugesan <sivaprak@codeaurora.org> Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Sricharan R <sricharan@codeaurora.org> --- drivers/pinctrl/qcom/Kconfig | 10 + drivers/pinctrl/qcom/Makefile | 1 + drivers/pinctrl/qcom/pinctrl-ipq6018.c | 1107 ++++++++++++++++++++++++++++++++ 3 files changed, 1118 insertions(+) create mode 100644 drivers/pinctrl/qcom/pinctrl-ipq6018.c diff --git a/drivers/pinctrl/qcom/Kconfig b/drivers/pinctrl/qcom/Kconfig index 811af2f8..c5d4428 100644 --- a/drivers/pinctrl/qcom/Kconfig +++ b/drivers/pinctrl/qcom/Kconfig @@ -50,6 +50,16 @@ config PINCTRL_IPQ8074 Qualcomm Technologies Inc. IPQ8074 platform. Select this for IPQ8074. +config PINCTRL_IPQ6018 + tristate "Qualcomm Technologies, Inc. IPQ6018 pin controller driver" + depends on GPIOLIB && OF + select PINCTRL_MSM + help + This is the pinctrl, pinmux, pinconf and gpiolib driver for + the Qualcomm Technologies Inc. TLMM block found on the + Qualcomm Technologies Inc. IPQ6018 platform. Select this for + IPQ6018. + config PINCTRL_MSM8660 tristate "Qualcomm 8660 pin controller driver" depends on GPIOLIB && OF diff --git a/drivers/pinctrl/qcom/Makefile b/drivers/pinctrl/qcom/Makefile index c2c2f9a..d9e0904 100644 --- a/drivers/pinctrl/qcom/Makefile +++ b/drivers/pinctrl/qcom/Makefile @@ -6,6 +6,7 @@ obj-$(CONFIG_PINCTRL_APQ8084) += pinctrl-apq8084.o obj-$(CONFIG_PINCTRL_IPQ4019) += pinctrl-ipq4019.o obj-$(CONFIG_PINCTRL_IPQ8064) += pinctrl-ipq8064.o obj-$(CONFIG_PINCTRL_IPQ8074) += pinctrl-ipq8074.o +obj-$(CONFIG_PINCTRL_IPQ6018) += pinctrl-ipq6018.o obj-$(CONFIG_PINCTRL_MSM8660) += pinctrl-msm8660.o obj-$(CONFIG_PINCTRL_MSM8960) += pinctrl-msm8960.o obj-$(CONFIG_PINCTRL_MSM8X74) += pinctrl-msm8x74.o diff --git a/drivers/pinctrl/qcom/pinctrl-ipq6018.c b/drivers/pinctrl/qcom/pinctrl-ipq6018.c new file mode 100644 index 0000000..38c33a7 --- /dev/null +++ b/drivers/pinctrl/qcom/pinctrl-ipq6018.c @@ -0,0 +1,1107 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2016-2018, The Linux Foundation. All rights reserved. + */ + +#include <linux/module.h> +#include <linux/of.h> +#include <linux/platform_device.h> +#include <linux/pinctrl/pinctrl.h> + +#include "pinctrl-msm.h" + +#define FUNCTION(fname) \ + [msm_mux_##fname] = { \ + .name = #fname, \ + .groups = fname##_groups, \ + .ngroups = ARRAY_SIZE(fname##_groups), \ + } + +#define REG_SIZE 0x1000 +#define PINGROUP(id, f1, f2, f3, f4, f5, f6, f7, f8, f9) \ + { \ + .name = "gpio" #id, \ + .pins = gpio##id##_pins, \ + .npins = (unsigned int)ARRAY_SIZE(gpio##id##_pins), \ + .funcs = (int[]){ \ + msm_mux_gpio, /* gpio mode */ \ + msm_mux_##f1, \ + msm_mux_##f2, \ + msm_mux_##f3, \ + msm_mux_##f4, \ + msm_mux_##f5, \ + msm_mux_##f6, \ + msm_mux_##f7, \ + msm_mux_##f8, \ + msm_mux_##f9 \ + }, \ + .nfuncs = 10, \ + .ctl_reg = REG_SIZE * id, \ + .io_reg = 0x4 + REG_SIZE * id, \ + .intr_cfg_reg = 0x8 + REG_SIZE * id, \ + .intr_status_reg = 0xc + REG_SIZE * id, \ + .intr_target_reg = 0x8 + REG_SIZE * id, \ + .mux_bit = 2, \ + .pull_bit = 0, \ + .drv_bit = 6, \ + .oe_bit = 9, \ + .in_bit = 0, \ + .out_bit = 1, \ + .intr_enable_bit = 0, \ + .intr_status_bit = 0, \ + .intr_target_bit = 5, \ + .intr_target_kpss_val = 3, \ + .intr_raw_status_bit = 4, \ + .intr_polarity_bit = 1, \ + .intr_detection_bit = 2, \ + .intr_detection_width = 2, \ + } + +static const struct pinctrl_pin_desc ipq6018_pins[] = { + PINCTRL_PIN(0, "GPIO_0"), + PINCTRL_PIN(1, "GPIO_1"), + PINCTRL_PIN(2, "GPIO_2"), + PINCTRL_PIN(3, "GPIO_3"), + PINCTRL_PIN(4, "GPIO_4"), + PINCTRL_PIN(5, "GPIO_5"), + PINCTRL_PIN(6, "GPIO_6"), + PINCTRL_PIN(7, "GPIO_7"), + PINCTRL_PIN(8, "GPIO_8"), + PINCTRL_PIN(9, "GPIO_9"), + PINCTRL_PIN(10, "GPIO_10"), + PINCTRL_PIN(11, "GPIO_11"), + PINCTRL_PIN(12, "GPIO_12"), + PINCTRL_PIN(13, "GPIO_13"), + PINCTRL_PIN(14, "GPIO_14"), + PINCTRL_PIN(15, "GPIO_15"), + PINCTRL_PIN(16, "GPIO_16"), + PINCTRL_PIN(17, "GPIO_17"), + PINCTRL_PIN(18, "GPIO_18"), + PINCTRL_PIN(19, "GPIO_19"), + PINCTRL_PIN(20, "GPIO_20"), + PINCTRL_PIN(21, "GPIO_21"), + PINCTRL_PIN(22, "GPIO_22"), + PINCTRL_PIN(23, "GPIO_23"), + PINCTRL_PIN(24, "GPIO_24"), + PINCTRL_PIN(25, "GPIO_25"), + PINCTRL_PIN(26, "GPIO_26"), + PINCTRL_PIN(27, "GPIO_27"), + PINCTRL_PIN(28, "GPIO_28"), + PINCTRL_PIN(29, "GPIO_29"), + PINCTRL_PIN(30, "GPIO_30"), + PINCTRL_PIN(31, "GPIO_31"), + PINCTRL_PIN(32, "GPIO_32"), + PINCTRL_PIN(33, "GPIO_33"), + PINCTRL_PIN(34, "GPIO_34"), + PINCTRL_PIN(35, "GPIO_35"), + PINCTRL_PIN(36, "GPIO_36"), + PINCTRL_PIN(37, "GPIO_37"), + PINCTRL_PIN(38, "GPIO_38"), + PINCTRL_PIN(39, "GPIO_39"), + PINCTRL_PIN(40, "GPIO_40"), + PINCTRL_PIN(41, "GPIO_41"), + PINCTRL_PIN(42, "GPIO_42"), + PINCTRL_PIN(43, "GPIO_43"), + PINCTRL_PIN(44, "GPIO_44"), + PINCTRL_PIN(45, "GPIO_45"), + PINCTRL_PIN(46, "GPIO_46"), + PINCTRL_PIN(47, "GPIO_47"), + PINCTRL_PIN(48, "GPIO_48"), + PINCTRL_PIN(49, "GPIO_49"), + PINCTRL_PIN(50, "GPIO_50"), + PINCTRL_PIN(51, "GPIO_51"), + PINCTRL_PIN(52, "GPIO_52"), + PINCTRL_PIN(53, "GPIO_53"), + PINCTRL_PIN(54, "GPIO_54"), + PINCTRL_PIN(55, "GPIO_55"), + PINCTRL_PIN(56, "GPIO_56"), + PINCTRL_PIN(57, "GPIO_57"), + PINCTRL_PIN(58, "GPIO_58"), + PINCTRL_PIN(59, "GPIO_59"), + PINCTRL_PIN(60, "GPIO_60"), + PINCTRL_PIN(61, "GPIO_61"), + PINCTRL_PIN(62, "GPIO_62"), + PINCTRL_PIN(63, "GPIO_63"), + PINCTRL_PIN(64, "GPIO_64"), + PINCTRL_PIN(65, "GPIO_65"), + PINCTRL_PIN(66, "GPIO_66"), + PINCTRL_PIN(67, "GPIO_67"), + PINCTRL_PIN(68, "GPIO_68"), + PINCTRL_PIN(69, "GPIO_69"), + PINCTRL_PIN(70, "GPIO_70"), + PINCTRL_PIN(71, "GPIO_71"), + PINCTRL_PIN(72, "GPIO_72"), + PINCTRL_PIN(73, "GPIO_73"), + PINCTRL_PIN(74, "GPIO_74"), + PINCTRL_PIN(75, "GPIO_75"), + PINCTRL_PIN(76, "GPIO_76"), + PINCTRL_PIN(77, "GPIO_77"), + PINCTRL_PIN(78, "GPIO_78"), + PINCTRL_PIN(79, "GPIO_79"), +}; + +#define DECLARE_MSM_GPIO_PINS(pin) \ + static const unsigned int gpio##pin##_pins[] = { pin } +DECLARE_MSM_GPIO_PINS(0); +DECLARE_MSM_GPIO_PINS(1); +DECLARE_MSM_GPIO_PINS(2); +DECLARE_MSM_GPIO_PINS(3); +DECLARE_MSM_GPIO_PINS(4); +DECLARE_MSM_GPIO_PINS(5); +DECLARE_MSM_GPIO_PINS(6); +DECLARE_MSM_GPIO_PINS(7); +DECLARE_MSM_GPIO_PINS(8); +DECLARE_MSM_GPIO_PINS(9); +DECLARE_MSM_GPIO_PINS(10); +DECLARE_MSM_GPIO_PINS(11); +DECLARE_MSM_GPIO_PINS(12); +DECLARE_MSM_GPIO_PINS(13); +DECLARE_MSM_GPIO_PINS(14); +DECLARE_MSM_GPIO_PINS(15); +DECLARE_MSM_GPIO_PINS(16); +DECLARE_MSM_GPIO_PINS(17); +DECLARE_MSM_GPIO_PINS(18); +DECLARE_MSM_GPIO_PINS(19); +DECLARE_MSM_GPIO_PINS(20); +DECLARE_MSM_GPIO_PINS(21); +DECLARE_MSM_GPIO_PINS(22); +DECLARE_MSM_GPIO_PINS(23); +DECLARE_MSM_GPIO_PINS(24); +DECLARE_MSM_GPIO_PINS(25); +DECLARE_MSM_GPIO_PINS(26); +DECLARE_MSM_GPIO_PINS(27); +DECLARE_MSM_GPIO_PINS(28); +DECLARE_MSM_GPIO_PINS(29); +DECLARE_MSM_GPIO_PINS(30); +DECLARE_MSM_GPIO_PINS(31); +DECLARE_MSM_GPIO_PINS(32); +DECLARE_MSM_GPIO_PINS(33); +DECLARE_MSM_GPIO_PINS(34); +DECLARE_MSM_GPIO_PINS(35); +DECLARE_MSM_GPIO_PINS(36); +DECLARE_MSM_GPIO_PINS(37); +DECLARE_MSM_GPIO_PINS(38); +DECLARE_MSM_GPIO_PINS(39); +DECLARE_MSM_GPIO_PINS(40); +DECLARE_MSM_GPIO_PINS(41); +DECLARE_MSM_GPIO_PINS(42); +DECLARE_MSM_GPIO_PINS(43); +DECLARE_MSM_GPIO_PINS(44); +DECLARE_MSM_GPIO_PINS(45); +DECLARE_MSM_GPIO_PINS(46); +DECLARE_MSM_GPIO_PINS(47); +DECLARE_MSM_GPIO_PINS(48); +DECLARE_MSM_GPIO_PINS(49); +DECLARE_MSM_GPIO_PINS(50); +DECLARE_MSM_GPIO_PINS(51); +DECLARE_MSM_GPIO_PINS(52); +DECLARE_MSM_GPIO_PINS(53); +DECLARE_MSM_GPIO_PINS(54); +DECLARE_MSM_GPIO_PINS(55); +DECLARE_MSM_GPIO_PINS(56); +DECLARE_MSM_GPIO_PINS(57); +DECLARE_MSM_GPIO_PINS(58); +DECLARE_MSM_GPIO_PINS(59); +DECLARE_MSM_GPIO_PINS(60); +DECLARE_MSM_GPIO_PINS(61); +DECLARE_MSM_GPIO_PINS(62); +DECLARE_MSM_GPIO_PINS(63); +DECLARE_MSM_GPIO_PINS(64); +DECLARE_MSM_GPIO_PINS(65); +DECLARE_MSM_GPIO_PINS(66); +DECLARE_MSM_GPIO_PINS(67); +DECLARE_MSM_GPIO_PINS(68); +DECLARE_MSM_GPIO_PINS(69); +DECLARE_MSM_GPIO_PINS(70); +DECLARE_MSM_GPIO_PINS(71); +DECLARE_MSM_GPIO_PINS(72); +DECLARE_MSM_GPIO_PINS(73); +DECLARE_MSM_GPIO_PINS(74); +DECLARE_MSM_GPIO_PINS(75); +DECLARE_MSM_GPIO_PINS(76); +DECLARE_MSM_GPIO_PINS(77); +DECLARE_MSM_GPIO_PINS(78); +DECLARE_MSM_GPIO_PINS(79); + +enum ipq6018_functions { + msm_mux_atest_char, + msm_mux_atest_char0, + msm_mux_atest_char1, + msm_mux_atest_char2, + msm_mux_atest_char3, + msm_mux_audio0, + msm_mux_audio1, + msm_mux_audio2, + msm_mux_audio3, + msm_mux_audio_rxbclk, + msm_mux_audio_rxfsync, + msm_mux_audio_rxmclk, + msm_mux_audio_rxmclkin, + msm_mux_audio_txbclk, + msm_mux_audio_txfsync, + msm_mux_audio_txmclk, + msm_mux_audio_txmclkin, + msm_mux_blsp0_i2c, + msm_mux_blsp0_spi, + msm_mux_blsp0_uart, + msm_mux_blsp1_i2c, + msm_mux_blsp1_spi, + msm_mux_blsp1_uart, + msm_mux_blsp2_i2c, + msm_mux_blsp2_spi, + msm_mux_blsp2_uart, + msm_mux_blsp3_i2c, + msm_mux_blsp3_spi, + msm_mux_blsp3_uart, + msm_mux_blsp4_i2c, + msm_mux_blsp4_spi, + msm_mux_blsp4_uart, + msm_mux_blsp5_i2c, + msm_mux_blsp5_uart, + msm_mux_burn0, + msm_mux_burn1, + msm_mux_cri_trng, + msm_mux_cri_trng0, + msm_mux_cri_trng1, + msm_mux_cxc0, + msm_mux_cxc1, + msm_mux_dbg_out, + msm_mux_gcc_plltest, + msm_mux_gcc_tlmm, + msm_mux_gpio, + msm_mux_lpass_aud, + msm_mux_lpass_aud0, + msm_mux_lpass_aud1, + msm_mux_lpass_aud2, + msm_mux_lpass_pcm, + msm_mux_lpass_pdm, + msm_mux_mac00, + msm_mux_mac01, + msm_mux_mac10, + msm_mux_mac11, + msm_mux_mac12, + msm_mux_mac13, + msm_mux_mac20, + msm_mux_mac21, + msm_mux_mdc, + msm_mux_mdio, + msm_mux_pcie0_clk, + msm_mux_pcie0_rst, + msm_mux_pcie0_wake, + msm_mux_prng_rosc, + msm_mux_pta1_0, + msm_mux_pta1_1, + msm_mux_pta1_2, + msm_mux_pta2_0, + msm_mux_pta2_1, + msm_mux_pta2_2, + msm_mux_pwm00, + msm_mux_pwm01, + msm_mux_pwm02, + msm_mux_pwm03, + msm_mux_pwm04, + msm_mux_pwm10, + msm_mux_pwm11, + msm_mux_pwm12, + msm_mux_pwm13, + msm_mux_pwm14, + msm_mux_pwm20, + msm_mux_pwm21, + msm_mux_pwm22, + msm_mux_pwm23, + msm_mux_pwm24, + msm_mux_pwm30, + msm_mux_pwm31, + msm_mux_pwm32, + msm_mux_pwm33, + msm_mux_qdss_cti_trig_in_a0, + msm_mux_qdss_cti_trig_in_a1, + msm_mux_qdss_cti_trig_out_a0, + msm_mux_qdss_cti_trig_out_a1, + msm_mux_qdss_cti_trig_in_b0, + msm_mux_qdss_cti_trig_in_b1, + msm_mux_qdss_cti_trig_out_b0, + msm_mux_qdss_cti_trig_out_b1, + msm_mux_qdss_traceclk_a, + msm_mux_qdss_tracectl_a, + msm_mux_qdss_tracedata_a, + msm_mux_qdss_traceclk_b, + msm_mux_qdss_tracectl_b, + msm_mux_qdss_tracedata_b, + msm_mux_qpic_pad, + msm_mux_rx0, + msm_mux_rx1, + msm_mux_rx_swrm, + msm_mux_rx_swrm0, + msm_mux_rx_swrm1, + msm_mux_sd_card, + msm_mux_sd_write, + msm_mux_tsens_max, + msm_mux_tx_swrm, + msm_mux_tx_swrm0, + msm_mux_tx_swrm1, + msm_mux_tx_swrm2, + msm_mux_wci20, + msm_mux_wci21, + msm_mux_wci22, + msm_mux_wci23, + msm_mux_wsa_swrm, + msm_mux__, +}; + +static const char * const blsp3_uart_groups[] = { + "gpio73", "gpio74", "gpio75", "gpio76", +}; + +static const char * const blsp3_i2c_groups[] = { + "gpio73", "gpio74", +}; + +static const char * const blsp3_spi_groups[] = { + "gpio73", "gpio74", "gpio75", "gpio76", "gpio77", "gpio78", "gpio79", +}; + +static const char * const wci20_groups[] = { + "gpio0", "gpio2", +}; + +static const char * const qpic_pad_groups[] = { + "gpio0", "gpio1", "gpio2", "gpio3", "gpio4", "gpio9", "gpio10", + "gpio11", "gpio17", +}; + +static const char * const burn0_groups[] = { + "gpio0", +}; + +static const char * const mac12_groups[] = { + "gpio1", "gpio11", +}; + +static const char * const qdss_tracectl_b_groups[] = { + "gpio1", +}; + +static const char * const burn1_groups[] = { + "gpio1", +}; + +static const char * const qdss_traceclk_b_groups[] = { + "gpio0", +}; + +static const char * const qdss_tracedata_b_groups[] = { + "gpio2", "gpio3", "gpio4", "gpio5", "gpio6", "gpio7", "gpio8", "gpio9", + "gpio10", "gpio11", "gpio12", "gpio13", "gpio14", "gpio15", "gpio16", + "gpio17", +}; + +static const char * const mac01_groups[] = { + "gpio3", "gpio4", +}; + +static const char * const mac21_groups[] = { + "gpio5", "gpio6", +}; + +static const char * const atest_char_groups[] = { + "gpio9", +}; + +static const char * const cxc0_groups[] = { + "gpio9", "gpio16", +}; + +static const char * const mac13_groups[] = { + "gpio9", "gpio16", +}; + +static const char * const dbg_out_groups[] = { + "gpio9", +}; + +static const char * const wci22_groups[] = { + "gpio11", "gpio17", +}; + +static const char * const pwm00_groups[] = { + "gpio18", +}; + +static const char * const atest_char0_groups[] = { + "gpio18", +}; + +static const char * const wci23_groups[] = { + "gpio18", "gpio19", +}; + +static const char * const mac11_groups[] = { + "gpio18", "gpio19", +}; + +static const char * const pwm10_groups[] = { + "gpio19", +}; + +static const char * const atest_char1_groups[] = { + "gpio19", +}; + +static const char * const pwm20_groups[] = { + "gpio20", +}; + +static const char * const atest_char2_groups[] = { + "gpio20", +}; + +static const char * const pwm30_groups[] = { + "gpio21", +}; + +static const char * const atest_char3_groups[] = { + "gpio21", +}; + +static const char * const audio_txmclk_groups[] = { + "gpio22", +}; + +static const char * const audio_txmclkin_groups[] = { + "gpio22", +}; + +static const char * const pwm02_groups[] = { + "gpio22", +}; + +static const char * const tx_swrm0_groups[] = { + "gpio22", +}; + +static const char * const qdss_cti_trig_out_b0_groups[] = { + "gpio22", +}; + +static const char * const audio_txbclk_groups[] = { + "gpio23", +}; + +static const char * const pwm12_groups[] = { + "gpio23", +}; + +static const char * const wsa_swrm_groups[] = { + "gpio23", "gpio24", +}; + +static const char * const tx_swrm1_groups[] = { + "gpio23", +}; + +static const char * const qdss_cti_trig_in_b0_groups[] = { + "gpio23", +}; + +static const char * const audio_txfsync_groups[] = { + "gpio24", +}; + +static const char * const pwm22_groups[] = { + "gpio24", +}; + +static const char * const tx_swrm2_groups[] = { + "gpio24", +}; + +static const char * const qdss_cti_trig_out_b1_groups[] = { + "gpio24", +}; + +static const char * const audio0_groups[] = { + "gpio25", "gpio32", +}; + +static const char * const pwm32_groups[] = { + "gpio25", +}; + +static const char * const tx_swrm_groups[] = { + "gpio25", +}; + +static const char * const qdss_cti_trig_in_b1_groups[] = { + "gpio25", +}; + +static const char * const audio1_groups[] = { + "gpio26", "gpio33", +}; + +static const char * const pwm04_groups[] = { + "gpio26", +}; + +static const char * const audio2_groups[] = { + "gpio27", +}; + +static const char * const pwm14_groups[] = { + "gpio27", +}; + +static const char * const audio3_groups[] = { + "gpio28", +}; + +static const char * const pwm24_groups[] = { + "gpio28", +}; + +static const char * const audio_rxmclk_groups[] = { + "gpio29", +}; + +static const char * const audio_rxmclkin_groups[] = { + "gpio29", +}; + +static const char * const pwm03_groups[] = { + "gpio29", +}; + +static const char * const lpass_pdm_groups[] = { + "gpio29", "gpio30", "gpio31", "gpio32", +}; + +static const char * const lpass_aud_groups[] = { + "gpio29", +}; + +static const char * const qdss_cti_trig_in_a1_groups[] = { + "gpio29", +}; + +static const char * const audio_rxbclk_groups[] = { + "gpio30", +}; + +static const char * const pwm13_groups[] = { + "gpio30", +}; + +static const char * const lpass_aud0_groups[] = { + "gpio30", +}; + +static const char * const rx_swrm_groups[] = { + "gpio30", +}; + +static const char * const qdss_cti_trig_out_a1_groups[] = { + "gpio30", +}; + +static const char * const audio_rxfsync_groups[] = { + "gpio31", +}; + +static const char * const pwm23_groups[] = { + "gpio31", +}; + +static const char * const lpass_aud1_groups[] = { + "gpio31", +}; + +static const char * const rx_swrm0_groups[] = { + "gpio31", +}; + +static const char * const qdss_cti_trig_in_a0_groups[] = { + "gpio31", +}; + +static const char * const pwm33_groups[] = { + "gpio32", +}; + +static const char * const lpass_aud2_groups[] = { + "gpio32", +}; + +static const char * const rx_swrm1_groups[] = { + "gpio32", +}; + +static const char * const qdss_cti_trig_out_a0_groups[] = { + "gpio32", +}; + +static const char * const lpass_pcm_groups[] = { + "gpio34", "gpio35", "gpio36", "gpio37", +}; + +static const char * const mac10_groups[] = { + "gpio34", "gpio35", +}; + +static const char * const mac00_groups[] = { + "gpio34", "gpio35", +}; + +static const char * const mac20_groups[] = { + "gpio36", "gpio37", +}; + +static const char * const blsp0_uart_groups[] = { + "gpio38", "gpio39", "gpio40", "gpio41", +}; + +static const char * const blsp0_i2c_groups[] = { + "gpio38", "gpio39", +}; + +static const char * const blsp0_spi_groups[] = { + "gpio38", "gpio39", "gpio40", "gpio41", +}; + +static const char * const blsp2_uart_groups[] = { + "gpio42", "gpio43", "gpio44", "gpio45", +}; + +static const char * const blsp2_i2c_groups[] = { + "gpio42", "gpio43", +}; + +static const char * const blsp2_spi_groups[] = { + "gpio42", "gpio43", "gpio44", "gpio45", +}; + +static const char * const blsp5_i2c_groups[] = { + "gpio46", "gpio47", +}; + +static const char * const blsp5_uart_groups[] = { + "gpio48", "gpio49", +}; + +static const char * const qdss_traceclk_a_groups[] = { + "gpio48", +}; + +static const char * const qdss_tracectl_a_groups[] = { + "gpio49", +}; + +static const char * const pwm01_groups[] = { + "gpio50", +}; + +static const char * const pta1_1_groups[] = { + "gpio51", +}; + +static const char * const pwm11_groups[] = { + "gpio51", +}; + +static const char * const rx1_groups[] = { + "gpio51", +}; + +static const char * const pta1_2_groups[] = { + "gpio52", +}; + +static const char * const pwm21_groups[] = { + "gpio52", +}; + +static const char * const pta1_0_groups[] = { + "gpio53", +}; + +static const char * const pwm31_groups[] = { + "gpio53", +}; + +static const char * const prng_rosc_groups[] = { + "gpio53", +}; + +static const char * const blsp4_uart_groups[] = { + "gpio55", "gpio56", "gpio57", "gpio58", +}; + +static const char * const blsp4_i2c_groups[] = { + "gpio55", "gpio56", +}; + +static const char * const blsp4_spi_groups[] = { + "gpio55", "gpio56", "gpio57", "gpio58", +}; + +static const char * const pcie0_clk_groups[] = { + "gpio59", +}; + +static const char * const cri_trng0_groups[] = { + "gpio59", +}; + +static const char * const pcie0_rst_groups[] = { + "gpio60", +}; + +static const char * const cri_trng1_groups[] = { + "gpio60", +}; + +static const char * const pcie0_wake_groups[] = { + "gpio61", +}; + +static const char * const cri_trng_groups[] = { + "gpio61", +}; + +static const char * const sd_card_groups[] = { + "gpio62", +}; + +static const char * const sd_write_groups[] = { + "gpio63", +}; + +static const char * const rx0_groups[] = { + "gpio63", +}; + +static const char * const tsens_max_groups[] = { + "gpio63", +}; + +static const char * const mdc_groups[] = { + "gpio64", +}; + +static const char * const qdss_tracedata_a_groups[] = { + "gpio64", "gpio65", "gpio66", "gpio67", "gpio68", "gpio69", "gpio70", + "gpio71", "gpio72", "gpio73", "gpio74", "gpio75", "gpio76", "gpio77", + "gpio78", "gpio79", +}; + +static const char * const mdio_groups[] = { + "gpio65", +}; + +static const char * const pta2_0_groups[] = { + "gpio66", +}; + +static const char * const wci21_groups[] = { + "gpio66", "gpio68", +}; + +static const char * const cxc1_groups[] = { + "gpio66", "gpio68", +}; + +static const char * const pta2_1_groups[] = { + "gpio67", +}; + +static const char * const pta2_2_groups[] = { + "gpio68", +}; + +static const char * const blsp1_uart_groups[] = { + "gpio69", "gpio70", "gpio71", "gpio72", +}; + +static const char * const blsp1_i2c_groups[] = { + "gpio69", "gpio70", +}; + +static const char * const blsp1_spi_groups[] = { + "gpio69", "gpio70", "gpio71", "gpio72", +}; + +static const char * const gcc_plltest_groups[] = { + "gpio69", "gpio71", +}; + +static const char * const gcc_tlmm_groups[] = { + "gpio70", +}; + +static const char * const gpio_groups[] = { + "gpio0", "gpio1", "gpio2", "gpio3", "gpio4", "gpio5", "gpio6", "gpio7", + "gpio8", "gpio9", "gpio10", "gpio11", "gpio12", "gpio13", "gpio14", + "gpio15", "gpio16", "gpio17", "gpio18", "gpio19", "gpio20", "gpio21", + "gpio22", "gpio23", "gpio24", "gpio25", "gpio26", "gpio27", "gpio28", + "gpio29", "gpio30", "gpio31", "gpio32", "gpio33", "gpio34", "gpio35", + "gpio36", "gpio37", "gpio38", "gpio39", "gpio40", "gpio41", "gpio42", + "gpio43", "gpio44", "gpio45", "gpio46", "gpio47", "gpio48", "gpio49", + "gpio50", "gpio51", "gpio52", "gpio53", "gpio54", "gpio55", "gpio56", + "gpio57", "gpio58", "gpio59", "gpio60", "gpio61", "gpio62", "gpio63", + "gpio64", "gpio65", "gpio66", "gpio67", "gpio68", "gpio69", "gpio70", + "gpio71", "gpio72", "gpio73", "gpio74", "gpio75", "gpio76", "gpio77", + "gpio78", "gpio79", +}; + +static const struct msm_function ipq6018_functions[] = { + FUNCTION(atest_char), + FUNCTION(atest_char0), + FUNCTION(atest_char1), + FUNCTION(atest_char2), + FUNCTION(atest_char3), + FUNCTION(audio0), + FUNCTION(audio1), + FUNCTION(audio2), + FUNCTION(audio3), + FUNCTION(audio_rxbclk), + FUNCTION(audio_rxfsync), + FUNCTION(audio_rxmclk), + FUNCTION(audio_rxmclkin), + FUNCTION(audio_txbclk), + FUNCTION(audio_txfsync), + FUNCTION(audio_txmclk), + FUNCTION(audio_txmclkin), + FUNCTION(blsp0_i2c), + FUNCTION(blsp0_spi), + FUNCTION(blsp0_uart), + FUNCTION(blsp1_i2c), + FUNCTION(blsp1_spi), + FUNCTION(blsp1_uart), + FUNCTION(blsp2_i2c), + FUNCTION(blsp2_spi), + FUNCTION(blsp2_uart), + FUNCTION(blsp3_i2c), + FUNCTION(blsp3_spi), + FUNCTION(blsp3_uart), + FUNCTION(blsp4_i2c), + FUNCTION(blsp4_spi), + FUNCTION(blsp4_uart), + FUNCTION(blsp5_i2c), + FUNCTION(blsp5_uart), + FUNCTION(burn0), + FUNCTION(burn1), + FUNCTION(cri_trng), + FUNCTION(cri_trng0), + FUNCTION(cri_trng1), + FUNCTION(cxc0), + FUNCTION(cxc1), + FUNCTION(dbg_out), + FUNCTION(gcc_plltest), + FUNCTION(gcc_tlmm), + FUNCTION(gpio), + FUNCTION(lpass_aud), + FUNCTION(lpass_aud0), + FUNCTION(lpass_aud1), + FUNCTION(lpass_aud2), + FUNCTION(lpass_pcm), + FUNCTION(lpass_pdm), + FUNCTION(mac00), + FUNCTION(mac01), + FUNCTION(mac10), + FUNCTION(mac11), + FUNCTION(mac12), + FUNCTION(mac13), + FUNCTION(mac20), + FUNCTION(mac21), + FUNCTION(mdc), + FUNCTION(mdio), + FUNCTION(pcie0_clk), + FUNCTION(pcie0_rst), + FUNCTION(pcie0_wake), + FUNCTION(prng_rosc), + FUNCTION(pta1_0), + FUNCTION(pta1_1), + FUNCTION(pta1_2), + FUNCTION(pta2_0), + FUNCTION(pta2_1), + FUNCTION(pta2_2), + FUNCTION(pwm00), + FUNCTION(pwm01), + FUNCTION(pwm02), + FUNCTION(pwm03), + FUNCTION(pwm04), + FUNCTION(pwm10), + FUNCTION(pwm11), + FUNCTION(pwm12), + FUNCTION(pwm13), + FUNCTION(pwm14), + FUNCTION(pwm20), + FUNCTION(pwm21), + FUNCTION(pwm22), + FUNCTION(pwm23), + FUNCTION(pwm24), + FUNCTION(pwm30), + FUNCTION(pwm31), + FUNCTION(pwm32), + FUNCTION(pwm33), + FUNCTION(qdss_cti_trig_in_a0), + FUNCTION(qdss_cti_trig_in_a1), + FUNCTION(qdss_cti_trig_out_a0), + FUNCTION(qdss_cti_trig_out_a1), + FUNCTION(qdss_cti_trig_in_b0), + FUNCTION(qdss_cti_trig_in_b1), + FUNCTION(qdss_cti_trig_out_b0), + FUNCTION(qdss_cti_trig_out_b1), + FUNCTION(qdss_traceclk_a), + FUNCTION(qdss_tracectl_a), + FUNCTION(qdss_tracedata_a), + FUNCTION(qdss_traceclk_b), + FUNCTION(qdss_tracectl_b), + FUNCTION(qdss_tracedata_b), + FUNCTION(qpic_pad), + FUNCTION(rx0), + FUNCTION(rx1), + FUNCTION(rx_swrm), + FUNCTION(rx_swrm0), + FUNCTION(rx_swrm1), + FUNCTION(sd_card), + FUNCTION(sd_write), + FUNCTION(tsens_max), + FUNCTION(tx_swrm), + FUNCTION(tx_swrm0), + FUNCTION(tx_swrm1), + FUNCTION(tx_swrm2), + FUNCTION(wci20), + FUNCTION(wci21), + FUNCTION(wci22), + FUNCTION(wci23), + FUNCTION(wsa_swrm), +}; + +static const struct msm_pingroup ipq6018_groups[] = { + PINGROUP(0, qpic_pad, wci20, qdss_traceclk_b, _, burn0, _, _, _, _), + PINGROUP(1, qpic_pad, mac12, qdss_tracectl_b, _, burn1, _, _, _, _), + PINGROUP(2, qpic_pad, wci20, qdss_tracedata_b, _, _, _, _, _, _), + PINGROUP(3, qpic_pad, mac01, qdss_tracedata_b, _, _, _, _, _, _), + PINGROUP(4, qpic_pad, mac01, qdss_tracedata_b, _, _, _, _, _, _), + PINGROUP(5, qpic_pad, mac21, qdss_tracedata_b, _, _, _, _, _, _), + PINGROUP(6, qpic_pad, mac21, qdss_tracedata_b, _, _, _, _, _, _), + PINGROUP(7, qpic_pad, qdss_tracedata_b, _, _, _, _, _, _, _), + PINGROUP(8, qpic_pad, qdss_tracedata_b, _, _, _, _, _, _, _), + PINGROUP(9, qpic_pad, atest_char, cxc0, mac13, dbg_out, qdss_tracedata_b, _, _, _), + PINGROUP(10, qpic_pad, qdss_tracedata_b, _, _, _, _, _, _, _), + PINGROUP(11, qpic_pad, wci22, mac12, qdss_tracedata_b, _, _, _, _, _), + PINGROUP(12, qpic_pad, qdss_tracedata_b, _, _, _, _, _, _, _), + PINGROUP(13, qpic_pad, qdss_tracedata_b, _, _, _, _, _, _, _), + PINGROUP(14, qpic_pad, qdss_tracedata_b, _, _, _, _, _, _, _), + PINGROUP(15, qpic_pad, qdss_tracedata_b, _, _, _, _, _, _, _), + PINGROUP(16, qpic_pad, cxc0, mac13, qdss_tracedata_b, _, _, _, _, _), + PINGROUP(17, qpic_pad, qdss_tracedata_b, wci22, _, _, _, _, _, _), + PINGROUP(18, pwm00, atest_char0, wci23, mac11, _, _, _, _, _), + PINGROUP(19, pwm10, atest_char1, wci23, mac11, _, _, _, _, _), + PINGROUP(20, pwm20, atest_char2, _, _, _, _, _, _, _), + PINGROUP(21, pwm30, atest_char3, _, _, _, _, _, _, _), + PINGROUP(22, audio_txmclk, audio_txmclkin, pwm02, tx_swrm0, _, qdss_cti_trig_out_b0, _, _, _), + PINGROUP(23, audio_txbclk, pwm12, wsa_swrm, tx_swrm1, _, qdss_cti_trig_in_b0, _, _, _), + PINGROUP(24, audio_txfsync, pwm22, wsa_swrm, tx_swrm2, _, qdss_cti_trig_out_b1, _, _, _), + PINGROUP(25, audio0, pwm32, tx_swrm, _, qdss_cti_trig_in_b1, _, _, _, _), + PINGROUP(26, audio1, pwm04, _, _, _, _, _, _, _), + PINGROUP(27, audio2, pwm14, _, _, _, _, _, _, _), + PINGROUP(28, audio3, pwm24, _, _, _, _, _, _, _), + PINGROUP(29, audio_rxmclk, audio_rxmclkin, pwm03, lpass_pdm, lpass_aud, qdss_cti_trig_in_a1, _, _, _), + PINGROUP(30, audio_rxbclk, pwm13, lpass_pdm, lpass_aud0, rx_swrm, _, qdss_cti_trig_out_a1, _, _), + PINGROUP(31, audio_rxfsync, pwm23, lpass_pdm, lpass_aud1, rx_swrm0, _, qdss_cti_trig_in_a0, _, _), + PINGROUP(32, audio0, pwm33, lpass_pdm, lpass_aud2, rx_swrm1, _, qdss_cti_trig_out_a0, _, _), + PINGROUP(33, audio1, _, _, _, _, _, _, _, _), + PINGROUP(34, lpass_pcm, mac10, mac00, _, _, _, _, _, _), + PINGROUP(35, lpass_pcm, mac10, mac00, _, _, _, _, _, _), + PINGROUP(36, lpass_pcm, mac20, _, _, _, _, _, _, _), + PINGROUP(37, lpass_pcm, mac20, _, _, _, _, _, _, _), + PINGROUP(38, blsp0_uart, blsp0_i2c, blsp0_spi, _, _, _, _, _, _), + PINGROUP(39, blsp0_uart, blsp0_i2c, blsp0_spi, _, _, _, _, _, _), + PINGROUP(40, blsp0_uart, blsp0_spi, _, _, _, _, _, _, _), + PINGROUP(41, blsp0_uart, blsp0_spi, _, _, _, _, _, _, _), + PINGROUP(42, blsp2_uart, blsp2_i2c, blsp2_spi, _, _, _, _, _, _), + PINGROUP(43, blsp2_uart, blsp2_i2c, blsp2_spi, _, _, _, _, _, _), + PINGROUP(44, blsp2_uart, blsp2_spi, _, _, _, _, _, _, _), + PINGROUP(45, blsp2_uart, blsp2_spi, _, _, _, _, _, _, _), + PINGROUP(46, blsp5_i2c, _, _, _, _, _, _, _, _), + PINGROUP(47, blsp5_i2c, _, _, _, _, _, _, _, _), + PINGROUP(48, blsp5_uart, _, qdss_traceclk_a, _, _, _, _, _, _), + PINGROUP(49, blsp5_uart, _, qdss_tracectl_a, _, _, _, _, _, _), + PINGROUP(50, pwm01, _, _, _, _, _, _, _, _), + PINGROUP(51, pta1_1, pwm11, _, rx1, _, _, _, _, _), + PINGROUP(52, pta1_2, pwm21, _, _, _, _, _, _, _), + PINGROUP(53, pta1_0, pwm31, prng_rosc, _, _, _, _, _, _), + PINGROUP(54, _, _, _, _, _, _, _, _, _), + PINGROUP(55, blsp4_uart, blsp4_i2c, blsp4_spi, _, _, _, _, _, _), + PINGROUP(56, blsp4_uart, blsp4_i2c, blsp4_spi, _, _, _, _, _, _), + PINGROUP(57, blsp4_uart, blsp4_spi, _, _, _, _, _, _, _), + PINGROUP(58, blsp4_uart, blsp4_spi, _, _, _, _, _, _, _), + PINGROUP(59, pcie0_clk, _, _, cri_trng0, _, _, _, _, _), + PINGROUP(60, pcie0_rst, _, _, cri_trng1, _, _, _, _, _), + PINGROUP(61, pcie0_wake, _, _, cri_trng, _, _, _, _, _), + PINGROUP(62, sd_card, _, _, _, _, _, _, _, _), + PINGROUP(63, sd_write, rx0, _, tsens_max, _, _, _, _, _), + PINGROUP(64, mdc, _, qdss_tracedata_a, _, _, _, _, _, _), + PINGROUP(65, mdio, _, qdss_tracedata_a, _, _, _, _, _, _), + PINGROUP(66, pta2_0, wci21, cxc1, qdss_tracedata_a, _, _, _, _, _), + PINGROUP(67, pta2_1, qdss_tracedata_a, _, _, _, _, _, _, _), + PINGROUP(68, pta2_2, wci21, cxc1, qdss_tracedata_a, _, _, _, _, _), + PINGROUP(69, blsp1_uart, blsp1_i2c, blsp1_spi, gcc_plltest, qdss_tracedata_a, _, _, _, _), + PINGROUP(70, blsp1_uart, blsp1_i2c, blsp1_spi, gcc_tlmm, qdss_tracedata_a, _, _, _, _), + PINGROUP(71, blsp1_uart, blsp1_spi, gcc_plltest, qdss_tracedata_a, _, _, _, _, _), + PINGROUP(72, blsp1_uart, blsp1_spi, qdss_tracedata_a, _, _, _, _, _, _), + PINGROUP(73, blsp3_uart, blsp3_i2c, blsp3_spi, _, qdss_tracedata_a, _, _, _, _), + PINGROUP(74, blsp3_uart, blsp3_i2c, blsp3_spi, _, qdss_tracedata_a, _, _, _, _), + PINGROUP(75, blsp3_uart, blsp3_spi, _, qdss_tracedata_a, _, _, _, _, _), + PINGROUP(76, blsp3_uart, blsp3_spi, _, qdss_tracedata_a, _, _, _, _, _), + PINGROUP(77, blsp3_spi, _, qdss_tracedata_a, _, _, _, _, _, _), + PINGROUP(78, blsp3_spi, _, qdss_tracedata_a, _, _, _, _, _, _), + PINGROUP(79, blsp3_spi, _, qdss_tracedata_a, _, _, _, _, _, _), +}; + +static const struct msm_pinctrl_soc_data ipq6018_pinctrl = { + .pins = ipq6018_pins, + .npins = ARRAY_SIZE(ipq6018_pins), + .functions = ipq6018_functions, + .nfunctions = ARRAY_SIZE(ipq6018_functions), + .groups = ipq6018_groups, + .ngroups = ARRAY_SIZE(ipq6018_groups), + .ngpios = 80, +}; + +static int ipq6018_pinctrl_probe(struct platform_device *pdev) +{ + return msm_pinctrl_probe(pdev, &ipq6018_pinctrl); +} + +static const struct of_device_id ipq6018_pinctrl_of_match[] = { + { .compatible = "qcom,ipq6018-pinctrl", }, + { }, +}; + +static struct platform_driver ipq6018_pinctrl_driver = { + .driver = { + .name = "ipq6018-pinctrl", + .of_match_table = ipq6018_pinctrl_of_match, + }, + .probe = ipq6018_pinctrl_probe, + .remove = msm_pinctrl_remove, +}; + +static int __init ipq6018_pinctrl_init(void) +{ + return platform_driver_register(&ipq6018_pinctrl_driver); +} +arch_initcall(ipq6018_pinctrl_init); + +static void __exit ipq6018_pinctrl_exit(void) +{ + platform_driver_unregister(&ipq6018_pinctrl_driver); +} +module_exit(ipq6018_pinctrl_exit); + +MODULE_DESCRIPTION("QTI ipq6018 pinctrl driver"); +MODULE_LICENSE("GPL v2"); +MODULE_DEVICE_TABLE(of, ipq6018_pinctrl_of_match); -- 2.7.4 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH V5 3/5] dt-bindings: qcom: Add ipq6018 bindings 2020-01-16 7:44 [PATCH V5 0/5] Add minimal boot support for IPQ6018 Sricharan R 2020-01-16 7:44 ` [PATCH V5 1/5] dt-bindings: pinctrl: qcom: Add ipq6018 pinctrl bindings Sricharan R 2020-01-16 7:44 ` [PATCH V5 2/5] pinctrl: qcom: Add ipq6018 pinctrl driver Sricharan R @ 2020-01-16 7:44 ` Sricharan R 2020-01-16 7:45 ` [PATCH V5 4/5] arm64: dts: Add ipq6018 SoC and CP01 board support Sricharan R 2020-01-16 7:45 ` [PATCH V5 5/5] arm64: defconfig: Enable qcom ipq6018 clock and pinctrl Sricharan R 4 siblings, 0 replies; 8+ messages in thread From: Sricharan R @ 2020-01-16 7:44 UTC (permalink / raw) To: agross, devicetree, linus.walleij, linux-arm-kernel, linux-arm-msm, linux-gpio, linux-kernel, linux-soc, robh+dt, sivaprak, sricharan Cc: Selvam Sathappan Periakaruppan Document the new ipq6018 SOC/board device tree bindings. Co-developed-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org> Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org> Co-developed-by: Sivaprakash Murugesan <sivaprak@codeaurora.org> Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Sricharan R <sricharan@codeaurora.org> --- Documentation/devicetree/bindings/arm/qcom.yaml | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml index 529d924..164177e 100644 --- a/Documentation/devicetree/bindings/arm/qcom.yaml +++ b/Documentation/devicetree/bindings/arm/qcom.yaml @@ -28,6 +28,7 @@ description: | apq8074 apq8084 apq8096 + ipq6018 ipq8074 mdm9615 msm8916 @@ -41,6 +42,7 @@ description: | The 'board' element must be one of the following strings: cdp + cp01-c1 dragonboard hk01 idp @@ -150,4 +152,10 @@ properties: - enum: - qcom,sc7180-idp - const: qcom,sc7180 + + - items: + - enum: + - qcom,ipq6018-cp01-c1 + - const: qcom,ipq6018 + ... -- 2.7.4 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH V5 4/5] arm64: dts: Add ipq6018 SoC and CP01 board support 2020-01-16 7:44 [PATCH V5 0/5] Add minimal boot support for IPQ6018 Sricharan R ` (2 preceding siblings ...) 2020-01-16 7:44 ` [PATCH V5 3/5] dt-bindings: qcom: Add ipq6018 bindings Sricharan R @ 2020-01-16 7:45 ` Sricharan R 2020-01-16 7:45 ` [PATCH V5 5/5] arm64: defconfig: Enable qcom ipq6018 clock and pinctrl Sricharan R 4 siblings, 0 replies; 8+ messages in thread From: Sricharan R @ 2020-01-16 7:45 UTC (permalink / raw) To: agross, devicetree, linus.walleij, linux-arm-kernel, linux-arm-msm, linux-gpio, linux-kernel, linux-soc, robh+dt, sivaprak, sricharan Cc: Abhishek Sahu Add initial device tree support for the Qualcomm IPQ6018 SoC and CP01 evaluation board. Co-developed-by: Abhishek Sahu <absahu@codeaurora.org> Signed-off-by: Abhishek Sahu <absahu@codeaurora.org> Co-developed-by: Sivaprakash Murugesan <sivaprak@codeaurora.org> Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org> Signed-off-by: Sricharan R <sricharan@codeaurora.org> --- [v5] *Added fixed clocks in gcc clock controller arch/arm64/boot/dts/qcom/Makefile | 1 + arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts | 30 ++++ arch/arm64/boot/dts/qcom/ipq6018.dtsi | 217 +++++++++++++++++++++++++++ 3 files changed, 248 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts create mode 100644 arch/arm64/boot/dts/qcom/ipq6018.dtsi diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index 973c0f0..204775f 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -2,6 +2,7 @@ dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc.dtb dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb +dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk01.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-longcheer-l8150.dtb diff --git a/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts b/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts new file mode 100644 index 0000000..897b4b2 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts @@ -0,0 +1,30 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) +/* + * IPQ6018 CP01 board device tree source + * + * Copyright (c) 2019, The Linux Foundation. All rights reserved. + */ + +/dts-v1/; + +#include "ipq6018.dtsi" + +/ { + model = "Qualcomm Technologies, Inc. IPQ6018/AP-CP01-C1"; + compatible = "qcom,ipq6018-cp01", "qcom,ipq6018"; + + aliases { + serial0 = &blsp1_uart3; + }; + + chosen { + stdout-path = "serial0:115200n8"; + bootargs-append = " swiotlb=1"; + }; +}; + +&blsp1_uart3 { + pinctrl-0 = <&serial_3_pins>; + pinctrl-names = "default"; + status = "ok"; +}; diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi b/arch/arm64/boot/dts/qcom/ipq6018.dtsi new file mode 100644 index 0000000..0fb44e5 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi @@ -0,0 +1,217 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) +/* + * IPQ6018 SoC device tree source + * + * Copyright (c) 2019, The Linux Foundation. All rights reserved. + */ + +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/clock/qcom,gcc-ipq6018.h> + +/ { + #address-cells = <2>; + #size-cells = <2>; + interrupt-parent = <&intc>; + + clocks { + sleep_clk: sleep-clk { + compatible = "fixed-clock"; + clock-frequency = <32000>; + #clock-cells = <0>; + }; + + xo: xo { + compatible = "fixed-clock"; + clock-frequency = <24000000>; + #clock-cells = <0>; + }; + }; + + cpus: cpus { + #address-cells = <1>; + #size-cells = <0>; + + CPU0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x0>; + enable-method = "psci"; + next-level-cache = <&L2_0>; + }; + + CPU1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + enable-method = "psci"; + reg = <0x1>; + next-level-cache = <&L2_0>; + }; + + CPU2: cpu@2 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + enable-method = "psci"; + reg = <0x2>; + next-level-cache = <&L2_0>; + }; + + CPU3: cpu@3 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + enable-method = "psci"; + reg = <0x3>; + next-level-cache = <&L2_0>; + }; + + L2_0: l2-cache { + compatible = "cache"; + cache-level = <0x2>; + }; + }; + + pmuv8: pmu { + compatible = "arm,cortex-a53-pmu"; + interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) | + IRQ_TYPE_LEVEL_HIGH)>; + }; + + psci: psci { + compatible = "arm,psci-1.0"; + method = "smc"; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + tz: tz@48500000 { + reg = <0x0 0x48500000 0x0 0x00200000>; + no-map; + }; + }; + + soc: soc { + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 0 0xffffffff>; + dma-ranges; + compatible = "simple-bus"; + + tlmm: pinctrl@1000000 { + compatible = "qcom,ipq6018-pinctrl"; + reg = <0x01000000 0x300000>; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&tlmm 0 80>; + interrupt-controller; + #interrupt-cells = <2>; + + serial_3_pins: serial3-pinmux { + pins = "gpio44", "gpio45"; + function = "blsp2_uart"; + drive-strength = <8>; + bias-pull-down; + }; + }; + + gcc: gcc@1800000 { + compatible = "qcom,gcc-ipq6018"; + reg = <0x01800000 0x80000>; + clocks = <&xo>, <&sleep_clk>; + clock-names = "xo", "sleep_clk"; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + blsp1_uart3: serial@78b1000 { + compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; + reg = <0x078b1000 0x200>; + interrupts = <GIC_SPI 306 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_UART3_APPS_CLK>, + <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + }; + + intc: interrupt-controller@b000000 { + compatible = "qcom,msm-qgic2"; + interrupt-controller; + #interrupt-cells = <0x3>; + reg = <0x0b000000 0x1000>, /*GICD*/ + <0x0b002000 0x1000>, /*GICC*/ + <0x0b001000 0x1000>, /*GICH*/ + <0x0b004000 0x1000>; /*GICV*/ + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; + }; + + timer@b120000 { + #address-cells = <1>; + #size-cells = <1>; + ranges; + compatible = "arm,armv7-timer-mem"; + reg = <0x0b120000 0x1000>; + clock-frequency = <19200000>; + + frame@b120000 { + frame-number = <0>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b121000 0x1000>, + <0x0b122000 0x1000>; + }; + + frame@b123000 { + frame-number = <1>; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; + reg = <0xb123000 0x1000>; + status = "disabled"; + }; + + frame@b124000 { + frame-number = <2>; + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b124000 0x1000>; + status = "disabled"; + }; + + frame@b125000 { + frame-number = <3>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b125000 0x1000>; + status = "disabled"; + }; + + frame@b126000 { + frame-number = <4>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b126000 0x1000>; + status = "disabled"; + }; + + frame@b127000 { + frame-number = <5>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b127000 0x1000>; + status = "disabled"; + }; + + frame@b128000 { + frame-number = <6>; + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b128000 0x1000>; + status = "disabled"; + }; + }; + + }; +}; -- 2.7.4 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH V5 5/5] arm64: defconfig: Enable qcom ipq6018 clock and pinctrl 2020-01-16 7:44 [PATCH V5 0/5] Add minimal boot support for IPQ6018 Sricharan R ` (3 preceding siblings ...) 2020-01-16 7:45 ` [PATCH V5 4/5] arm64: dts: Add ipq6018 SoC and CP01 board support Sricharan R @ 2020-01-16 7:45 ` Sricharan R 4 siblings, 0 replies; 8+ messages in thread From: Sricharan R @ 2020-01-16 7:45 UTC (permalink / raw) To: agross, devicetree, linus.walleij, linux-arm-kernel, linux-arm-msm, linux-gpio, linux-kernel, linux-soc, robh+dt, sivaprak, sricharan These configs are required for booting kernel in qcom ipq6018 boards. Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Sricharan R <sricharan@codeaurora.org> --- arch/arm64/configs/defconfig | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig index 43fa238..16aecea 100644 --- a/arch/arm64/configs/defconfig +++ b/arch/arm64/configs/defconfig @@ -405,6 +405,7 @@ CONFIG_PINCTRL_IMX8MN=y CONFIG_PINCTRL_IMX8MQ=y CONFIG_PINCTRL_IMX8QXP=y CONFIG_PINCTRL_IPQ8074=y +CONFIG_PINCTRL_IPQ6018=y CONFIG_PINCTRL_MSM8916=y CONFIG_PINCTRL_MSM8994=y CONFIG_PINCTRL_MSM8996=y @@ -718,6 +719,7 @@ CONFIG_QCOM_CLK_APCS_MSM8916=y CONFIG_QCOM_CLK_SMD_RPM=y CONFIG_QCOM_CLK_RPMH=y CONFIG_IPQ_GCC_8074=y +CONFIG_IPQ_GCC_6018=y CONFIG_MSM_GCC_8916=y CONFIG_MSM_GCC_8994=y CONFIG_MSM_MMCC_8996=y -- 2.7.4 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 8+ messages in thread
end of thread, other threads:[~2020-01-19 13:16 UTC | newest] Thread overview: 8+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2020-01-16 7:44 [PATCH V5 0/5] Add minimal boot support for IPQ6018 Sricharan R 2020-01-16 7:44 ` [PATCH V5 1/5] dt-bindings: pinctrl: qcom: Add ipq6018 pinctrl bindings Sricharan R 2020-01-17 16:01 ` Rob Herring 2020-01-19 13:15 ` Sricharan R 2020-01-16 7:44 ` [PATCH V5 2/5] pinctrl: qcom: Add ipq6018 pinctrl driver Sricharan R 2020-01-16 7:44 ` [PATCH V5 3/5] dt-bindings: qcom: Add ipq6018 bindings Sricharan R 2020-01-16 7:45 ` [PATCH V5 4/5] arm64: dts: Add ipq6018 SoC and CP01 board support Sricharan R 2020-01-16 7:45 ` [PATCH V5 5/5] arm64: defconfig: Enable qcom ipq6018 clock and pinctrl Sricharan R
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).