* FW: [PATCH V4] ARM: dts: add minimal DT support for DevKit8000. [not found] <F3DBB1B3EF102E4994C89758CFCA32412CC4E9@DBDE01.ent.ti.com> @ 2013-02-27 2:33 ` Anil Kumar [not found] ` <F3DBB1B3EF102E4994C89758CFCA32412CC74F@DBDE01.ent.ti.com> 0 siblings, 1 reply; 9+ messages in thread From: Anil Kumar @ 2013-02-27 2:33 UTC (permalink / raw) To: linux-arm-kernel Hi, > > DevKit8000 is a beagle board clone from Timll, sold by > armkits.com. The DevKit8000 has RS232 serial port, LCD, DVI-D, > S-Video, Ethernet, SD/MMC, keyboard, camera, SPI, I2C, USB and > JTAG interface. > > This patch adds the basic DT support for devkit8000. At this time, Information > of twl4030 (PMIC), MMC1, I2C1 and leds are added. > > Signed-off-by: Anil Kumar <anilk4.v@gmail.com> > Tested-by: Thomas Weber <thomas@tomweber.eu> Gentle Ping. As there are no review comments on this patch, Could you please pull this patch ? Thanks, Anil > --- > -This patch is based on top of kernel 3.8-rc5. > > -Tested on Devkit8000. > > For V4: > -Tiny nitpick. > > For V3: > - Remove pin mux as done at device boot time by default. > > For V2: > - Change model name as "TimLL OMAP3 Devkit8000" > - Change compatible as "timll,omap3-devkit8000" > - Doing i2c1 pinmux default with pinctrl-single driver instead of i2c1 > driver probe time. > > :100644 100644 5ebb44f... 22ebc76... M arch/arm/boot/dts/Makefile > :000000 100644 0000000... 2e1463a... A arch/arm/boot/dts/omap3-devkit8000.dts > :100644 100644 53cb380b.. ccecb76... M arch/arm/mach-omap2/board-generic.c > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/omap3-devkit8000.dts | 102 ++++++++++++++++++++++++++++++++ > arch/arm/mach-omap2/board-generic.c | 1 + > 3 files changed, 104 insertions(+), 0 deletions(-) > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index 5ebb44f..22ebc76 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -102,6 +102,7 @@ dtb-$(CONFIG_ARCH_MXS) += imx23-evk.dtb \ > imx28-tx28.dtb > dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \ > omap3-beagle.dtb \ > + omap3-devkit8000.dtb \ > omap3-beagle-xm.dtb \ > omap3-evm.dtb \ > omap3-tobi.dtb \ > diff --git a/arch/arm/boot/dts/omap3-devkit8000.dts b/arch/arm/boot/dts/omap3-devkit8000.dts > new file mode 100644 > index 0000000..2e1463a > --- /dev/null > +++ b/arch/arm/boot/dts/omap3-devkit8000.dts > @@ -0,0 +1,102 @@ > +/* > + * Author: Anil Kumar <anilk4.v@gmail.com> > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > + */ > +/dts-v1/; > + > +/include/ "omap3.dtsi" > +/ { > + model = "TimLL OMAP3 Devkit8000"; > + compatible = "timll,omap3-devkit8000", "ti,omap3"; > + > + memory { > + device_type = "memory"; > + reg = <0x80000000 0x10000000>; /* 256 MB */ > + }; > + > + leds { > + compatible = "gpio-leds"; > + > + heartbeat { > + label = "devkit8000::led1"; > + gpios = <&gpio6 26 0>; /* 186 -> LED1 */ > + default-state = "on"; > + linux,default-trigger = "heartbeat"; > + }; > + > + mmc { > + label = "devkit8000::led2"; > + gpios = <&gpio6 3 0>; /* 163 -> LED2 */ > + default-state = "on"; > + linux,default-trigger = "none"; > + }; > + > + usr { > + label = "devkit8000::led3"; > + gpios = <&gpio6 4 0>; /* 164 -> LED3 */ > + default-state = "on"; > + linux,default-trigger = "usr"; > + }; > + }; > +}; > + > +&i2c1 { > + clock-frequency = <2600000>; > + > + twl: twl at 48 { > + reg = <0x48>; > + interrupts = <7>; /* SYS_NIRQ cascaded to intc */ > + interrupt-parent = <&intc>; > + }; > +}; > + > +&i2c2 { > + status = "disabled"; > +}; > + > +&i2c3 { > + status = "disabled"; > +}; > + > +/include/ "twl4030.dtsi" > + > +&mmc1 { > + vmmc-supply = <&vmmc1>; > + vmmc_aux-supply = <&vsim>; > + bus-width = <8>; > +}; > + > +&mmc2 { > + status = "disabled"; > +}; > + > +&mmc3 { > + status = "disabled"; > +}; > + > +&wdt2 { > + status = "disabled"; > +}; > + > +&mcbsp1 { > + status = "disabled"; > +}; > + > +&mcbsp2 { > + status = "disabled"; > +}; > + > +&mcbsp3 { > + status = "disabled"; > +}; > + > +&mcbsp4 { > + status = "disabled"; > +}; > + > +&mcbsp5 { > + status = "disabled"; > +}; > diff --git a/arch/arm/mach-omap2/board-generic.c b/arch/arm/mach-omap2/board-generic.c > index 53cb380..ccecb76 100644 > --- a/arch/arm/mach-omap2/board-generic.c > +++ b/arch/arm/mach-omap2/board-generic.c > @@ -110,6 +110,7 @@ MACHINE_END > > static const char *omap3_gp_boards_compat[] __initdata = { > "ti,omap3-beagle", > + "timll,omap3-devkit8000", > NULL, > }; > > -- > 1.7.0.4 > > > _______________________________________________ > linux-arm-kernel mailing list > linux-arm-kernel at lists.infradead.org > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 9+ messages in thread
[parent not found: <F3DBB1B3EF102E4994C89758CFCA32412CC74F@DBDE01.ent.ti.com>]
* [PATCH V4] ARM: dts: add minimal DT support for DevKit8000. [not found] ` <F3DBB1B3EF102E4994C89758CFCA32412CC74F@DBDE01.ent.ti.com> @ 2013-03-06 2:36 ` Anil Kumar 2013-03-06 17:53 ` Tony Lindgren 0 siblings, 1 reply; 9+ messages in thread From: Anil Kumar @ 2013-03-06 2:36 UTC (permalink / raw) To: linux-arm-kernel Hi Tony, >> From: linux-arm-kernel [mailto:linux-arm-kernel- >> bounces at lists.infradead.org] On Behalf Of Anil Kumar >> Sent: Wednesday, February 27, 2013 8:03 AM >> To: devicetree-discuss at lists.ozlabs.org; linux-omap at vger.kernel.org; >> linux-kernel at vger.kernel.org; linux-arm-kernel at lists.infradead.org >> Cc: linux at arm.linux.org.uk; Cousson, Benoit; Tony Lindgren; Grant >> Likely; Anil Kumar; thomas at tomweber.eu >> Subject: Re: FW: [PATCH V4] ARM: dts: add minimal DT support for >> DevKit8000. >> >> Hi, >> > >> > DevKit8000 is a beagle board clone from Timll, sold by >> > armkits.com. The DevKit8000 has RS232 serial port, LCD, DVI-D, >> > S-Video, Ethernet, SD/MMC, keyboard, camera, SPI, I2C, USB and >> > JTAG interface. >> > >> > This patch adds the basic DT support for devkit8000. At this time, >> Information >> > of twl4030 (PMIC), MMC1, I2C1 and leds are added. >> > >> > Signed-off-by: Anil Kumar <anilk4.v@gmail.com> >> > Tested-by: Thomas Weber <thomas@tomweber.eu> >> >> Gentle Ping. As there are no review comments on this patch, >> Could you please pull this patch ? Gentle Ping. This patch also got Reviewed-by: Manish Badarkhe <badarkhe.manish@gmail.com> and as patch "ARM: dts: omap3-devkit8000: Enable audio support" has already got "Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>" but it is on the top of this patch. So, Could you please pull this patch in one of your omap branch? or you want me to do rebase this patch on top of v3.9-rc1 ? Thanks, Anil >> >> > --- >> > -This patch is based on top of kernel 3.8-rc5. >> > >> > -Tested on Devkit8000. >> > >> > For V4: >> > -Tiny nitpick. >> > >> > For V3: >> > - Remove pin mux as done at device boot time by default. >> > >> > For V2: >> > - Change model name as "TimLL OMAP3 Devkit8000" >> > - Change compatible as "timll,omap3-devkit8000" >> > - Doing i2c1 pinmux default with pinctrl-single driver instead of >> i2c1 >> > driver probe time. >> > >> > :100644 100644 5ebb44f... 22ebc76... M arch/arm/boot/dts/Makefile >> > :000000 100644 0000000... 2e1463a... A arch/arm/boot/dts/omap3- >> devkit8000.dts >> > :100644 100644 53cb380b.. ccecb76... M arch/arm/mach-omap2/board- >> generic.c >> > arch/arm/boot/dts/Makefile | 1 + >> > arch/arm/boot/dts/omap3-devkit8000.dts | 102 >> ++++++++++++++++++++++++++++++++ >> > arch/arm/mach-omap2/board-generic.c | 1 + >> > 3 files changed, 104 insertions(+), 0 deletions(-) >> > >> > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile >> > index 5ebb44f..22ebc76 100644 >> > --- a/arch/arm/boot/dts/Makefile >> > +++ b/arch/arm/boot/dts/Makefile >> > @@ -102,6 +102,7 @@ dtb-$(CONFIG_ARCH_MXS) += imx23-evk.dtb \ >> > imx28-tx28.dtb >> > dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \ >> > omap3-beagle.dtb \ >> > + omap3-devkit8000.dtb \ >> > omap3-beagle-xm.dtb \ >> > omap3-evm.dtb \ >> > omap3-tobi.dtb \ >> > diff --git a/arch/arm/boot/dts/omap3-devkit8000.dts >> b/arch/arm/boot/dts/omap3-devkit8000.dts >> > new file mode 100644 >> > index 0000000..2e1463a >> > --- /dev/null >> > +++ b/arch/arm/boot/dts/omap3-devkit8000.dts >> > @@ -0,0 +1,102 @@ >> > +/* >> > + * Author: Anil Kumar <anilk4.v@gmail.com> >> > + * >> > + * This program is free software; you can redistribute it and/or >> modify >> > + * it under the terms of the GNU General Public License version 2 as >> > + * published by the Free Software Foundation. >> > + */ >> > +/dts-v1/; >> > + >> > +/include/ "omap3.dtsi" >> > +/ { >> > + model = "TimLL OMAP3 Devkit8000"; >> > + compatible = "timll,omap3-devkit8000", "ti,omap3"; >> > + >> > + memory { >> > + device_type = "memory"; >> > + reg = <0x80000000 0x10000000>; /* 256 MB */ >> > + }; >> > + >> > + leds { >> > + compatible = "gpio-leds"; >> > + >> > + heartbeat { >> > + label = "devkit8000::led1"; >> > + gpios = <&gpio6 26 0>; /* 186 -> LED1 */ >> > + default-state = "on"; >> > + linux,default-trigger = "heartbeat"; >> > + }; >> > + >> > + mmc { >> > + label = "devkit8000::led2"; >> > + gpios = <&gpio6 3 0>; /* 163 -> LED2 */ >> > + default-state = "on"; >> > + linux,default-trigger = "none"; >> > + }; >> > + >> > + usr { >> > + label = "devkit8000::led3"; >> > + gpios = <&gpio6 4 0>; /* 164 -> LED3 */ >> > + default-state = "on"; >> > + linux,default-trigger = "usr"; >> > + }; >> > + }; >> > +}; >> > + >> > +&i2c1 { >> > + clock-frequency = <2600000>; >> > + >> > + twl: twl at 48 { >> > + reg = <0x48>; >> > + interrupts = <7>; /* SYS_NIRQ cascaded to intc >> */ >> > + interrupt-parent = <&intc>; >> > + }; >> > +}; >> > + >> > +&i2c2 { >> > + status = "disabled"; >> > +}; >> > + >> > +&i2c3 { >> > + status = "disabled"; >> > +}; >> > + >> > +/include/ "twl4030.dtsi" >> > + >> > +&mmc1 { >> > + vmmc-supply = <&vmmc1>; >> > + vmmc_aux-supply = <&vsim>; >> > + bus-width = <8>; >> > +}; >> > + >> > +&mmc2 { >> > + status = "disabled"; >> > +}; >> > + >> > +&mmc3 { >> > + status = "disabled"; >> > +}; >> > + >> > +&wdt2 { >> > + status = "disabled"; >> > +}; >> > + >> > +&mcbsp1 { >> > + status = "disabled"; >> > +}; >> > + >> > +&mcbsp2 { >> > + status = "disabled"; >> > +}; >> > + >> > +&mcbsp3 { >> > + status = "disabled"; >> > +}; >> > + >> > +&mcbsp4 { >> > + status = "disabled"; >> > +}; >> > + >> > +&mcbsp5 { >> > + status = "disabled"; >> > +}; >> > diff --git a/arch/arm/mach-omap2/board-generic.c b/arch/arm/mach- >> omap2/board-generic.c >> > index 53cb380..ccecb76 100644 >> > --- a/arch/arm/mach-omap2/board-generic.c >> > +++ b/arch/arm/mach-omap2/board-generic.c >> > @@ -110,6 +110,7 @@ MACHINE_END >> > >> > static const char *omap3_gp_boards_compat[] __initdata = { >> > "ti,omap3-beagle", >> > + "timll,omap3-devkit8000", >> > NULL, >> > }; >> > >> > -- >> > 1.7.0.4 >> > >> > >> > _______________________________________________ >> > linux-arm-kernel mailing list >> > linux-arm-kernel at lists.infradead.org >> > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel >> >> _______________________________________________ >> linux-arm-kernel mailing list >> linux-arm-kernel at lists.infradead.org >> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH V4] ARM: dts: add minimal DT support for DevKit8000. 2013-03-06 2:36 ` Anil Kumar @ 2013-03-06 17:53 ` Tony Lindgren 2013-03-07 6:51 ` Benoit Cousson 0 siblings, 1 reply; 9+ messages in thread From: Tony Lindgren @ 2013-03-06 17:53 UTC (permalink / raw) To: linux-arm-kernel * Anil Kumar <anilk4.v@gmail.com> [130305 18:40]: > Hi Tony, > > >> From: linux-arm-kernel [mailto:linux-arm-kernel- > >> bounces at lists.infradead.org] On Behalf Of Anil Kumar > >> Sent: Wednesday, February 27, 2013 8:03 AM > >> To: devicetree-discuss at lists.ozlabs.org; linux-omap at vger.kernel.org; > >> linux-kernel at vger.kernel.org; linux-arm-kernel at lists.infradead.org > >> Cc: linux at arm.linux.org.uk; Cousson, Benoit; Tony Lindgren; Grant > >> Likely; Anil Kumar; thomas at tomweber.eu > >> Subject: Re: FW: [PATCH V4] ARM: dts: add minimal DT support for > >> DevKit8000. > >> > >> Hi, > >> > > >> > DevKit8000 is a beagle board clone from Timll, sold by > >> > armkits.com. The DevKit8000 has RS232 serial port, LCD, DVI-D, > >> > S-Video, Ethernet, SD/MMC, keyboard, camera, SPI, I2C, USB and > >> > JTAG interface. > >> > > >> > This patch adds the basic DT support for devkit8000. At this time, > >> Information > >> > of twl4030 (PMIC), MMC1, I2C1 and leds are added. > >> > > >> > Signed-off-by: Anil Kumar <anilk4.v@gmail.com> > >> > Tested-by: Thomas Weber <thomas@tomweber.eu> > >> > >> Gentle Ping. As there are no review comments on this patch, > >> Could you please pull this patch ? > > Gentle Ping. > > This patch also got Reviewed-by: Manish Badarkhe <badarkhe.manish@gmail.com> > and as patch "ARM: dts: omap3-devkit8000: Enable audio support" has already got > "Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>" but it is on the > top of this patch. > So, Could you please pull this patch in one of your omap branch? or > you want me to > do rebase this patch on top of v3.9-rc1 ? Let's wait for Benoit to queue it as he has a bunch of .dts changes already applied. Too bad we missed v3.9 merge window for those, but hopefully we can get them queued early for v3.10. Regards, Tony ^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH V4] ARM: dts: add minimal DT support for DevKit8000. 2013-03-06 17:53 ` Tony Lindgren @ 2013-03-07 6:51 ` Benoit Cousson 2013-03-07 16:10 ` Tony Lindgren 2013-03-17 5:23 ` Anil Kumar 0 siblings, 2 replies; 9+ messages in thread From: Benoit Cousson @ 2013-03-07 6:51 UTC (permalink / raw) To: linux-arm-kernel Hi, On 03/06/2013 06:53 PM, Tony Lindgren wrote: > * Anil Kumar <anilk4.v@gmail.com> [130305 18:40]: >> Hi Tony, >> >>>> From: linux-arm-kernel [mailto:linux-arm-kernel- >>>> bounces at lists.infradead.org] On Behalf Of Anil Kumar >>>> Sent: Wednesday, February 27, 2013 8:03 AM >>>> To: devicetree-discuss at lists.ozlabs.org; linux-omap at vger.kernel.org; >>>> linux-kernel at vger.kernel.org; linux-arm-kernel at lists.infradead.org >>>> Cc: linux at arm.linux.org.uk; Cousson, Benoit; Tony Lindgren; Grant >>>> Likely; Anil Kumar; thomas at tomweber.eu >>>> Subject: Re: FW: [PATCH V4] ARM: dts: add minimal DT support for >>>> DevKit8000. >>>> >>>> Hi, >>>>> >>>>> DevKit8000 is a beagle board clone from Timll, sold by >>>>> armkits.com. The DevKit8000 has RS232 serial port, LCD, DVI-D, >>>>> S-Video, Ethernet, SD/MMC, keyboard, camera, SPI, I2C, USB and >>>>> JTAG interface. >>>>> >>>>> This patch adds the basic DT support for devkit8000. At this time, >>>> Information >>>>> of twl4030 (PMIC), MMC1, I2C1 and leds are added. >>>>> >>>>> Signed-off-by: Anil Kumar <anilk4.v@gmail.com> >>>>> Tested-by: Thomas Weber <thomas@tomweber.eu> >>>> >>>> Gentle Ping. As there are no review comments on this patch, >>>> Could you please pull this patch ? >> >> Gentle Ping. >> >> This patch also got Reviewed-by: Manish Badarkhe <badarkhe.manish@gmail.com> >> and as patch "ARM: dts: omap3-devkit8000: Enable audio support" has already got >> "Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>" but it is on the >> top of this patch. >> So, Could you please pull this patch in one of your omap branch? or >> you want me to >> do rebase this patch on top of v3.9-rc1 ? > > Let's wait for Benoit to queue it as he has a bunch of .dts changes already > applied. Too bad we missed v3.9 merge window for those, but hopefully > we can get them queued early for v3.10. Yep, sorry for having missed 3.9, I was a little bit sick at the wrong moment :-( I'm starting queuing the pending patches, and should have enough to push to you just after Linaro Connect. Regards, Benoit ^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH V4] ARM: dts: add minimal DT support for DevKit8000. 2013-03-07 6:51 ` Benoit Cousson @ 2013-03-07 16:10 ` Tony Lindgren 2013-03-17 5:23 ` Anil Kumar 1 sibling, 0 replies; 9+ messages in thread From: Tony Lindgren @ 2013-03-07 16:10 UTC (permalink / raw) To: linux-arm-kernel * Benoit Cousson <b-cousson@ti.com> [130306 22:55]: > > Yep, sorry for having missed 3.9, I was a little bit sick at the wrong > moment :-( Well that just proves the .dts files can be merged totally independent of the rest of the patches ;) > I'm starting queuing the pending patches, and should have enough to push > to you just after Linaro Connect. OK sounds good. Regards, Tony ^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH V4] ARM: dts: add minimal DT support for DevKit8000. 2013-03-07 6:51 ` Benoit Cousson 2013-03-07 16:10 ` Tony Lindgren @ 2013-03-17 5:23 ` Anil Kumar 2013-03-18 15:21 ` Benoit Cousson 1 sibling, 1 reply; 9+ messages in thread From: Anil Kumar @ 2013-03-17 5:23 UTC (permalink / raw) To: linux-arm-kernel Hi Benoit, On Thu, Mar 7, 2013 at 12:21 PM, Benoit Cousson <b-cousson@ti.com> wrote: > Hi, > > On 03/06/2013 06:53 PM, Tony Lindgren wrote: >> * Anil Kumar <anilk4.v@gmail.com> [130305 18:40]: >>> Hi Tony, >>> >>>>> From: linux-arm-kernel [mailto:linux-arm-kernel- >>>>> bounces at lists.infradead.org] On Behalf Of Anil Kumar >>>>> Sent: Wednesday, February 27, 2013 8:03 AM >>>>> To: devicetree-discuss at lists.ozlabs.org; linux-omap at vger.kernel.org; >>>>> linux-kernel at vger.kernel.org; linux-arm-kernel at lists.infradead.org >>>>> Cc: linux at arm.linux.org.uk; Cousson, Benoit; Tony Lindgren; Grant >>>>> Likely; Anil Kumar; thomas at tomweber.eu >>>>> Subject: Re: FW: [PATCH V4] ARM: dts: add minimal DT support for >>>>> DevKit8000. >>>>> >>>>> Hi, >>>>>> >>>>>> DevKit8000 is a beagle board clone from Timll, sold by >>>>>> armkits.com. The DevKit8000 has RS232 serial port, LCD, DVI-D, >>>>>> S-Video, Ethernet, SD/MMC, keyboard, camera, SPI, I2C, USB and >>>>>> JTAG interface. >>>>>> >>>>>> This patch adds the basic DT support for devkit8000. At this time, >>>>> Information >>>>>> of twl4030 (PMIC), MMC1, I2C1 and leds are added. >>>>>> >>>>>> Signed-off-by: Anil Kumar <anilk4.v@gmail.com> >>>>>> Tested-by: Thomas Weber <thomas@tomweber.eu> >>>>> >>>>> Gentle Ping. As there are no review comments on this patch, >>>>> Could you please pull this patch ? >>> >>> Gentle Ping. >>> >>> This patch also got Reviewed-by: Manish Badarkhe <badarkhe.manish@gmail.com> >>> and as patch "ARM: dts: omap3-devkit8000: Enable audio support" has already got >>> "Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>" but it is on the >>> top of this patch. >>> So, Could you please pull this patch in one of your omap branch? or >>> you want me to >>> do rebase this patch on top of v3.9-rc1 ? >> >> Let's wait for Benoit to queue it as he has a bunch of .dts changes already >> applied. Too bad we missed v3.9 merge window for those, but hopefully >> we can get them queued early for v3.10. > > Yep, sorry for having missed 3.9, I was a little bit sick at the wrong > moment :-( > > I'm starting queuing the pending patches, and should have enough to push > to you just after Linaro Connect. I think you missed below patch which is needed for gpmc nand to work fine. Jon Hunter:- ARM: OMAP2+: Fix-up gpmc merge error I have re based my changes on top of your repository to make pull easier for you. I hope you will pull these changes for 3.10. The following changes since Commit a7f7881de9c0b58de3b3aea8f01a8aef906d4ade are available in the git repository at: git://gitorious.org/devkit8000-for_3-10/devkit8000-for_3-10.git branch for_3.10/dts for you to fetch changes up to Commit 975abc8b2e7ec4ff7324d726c9775958945ccc5e Anil Kumar: ARM: dts: add minimal DT support for DevKit8000 ARM: dts: omap3-devkit8000: Enable audio support ARM: dts: omap3-devkit8000: add nand dt node Thanks, Anil ^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH V4] ARM: dts: add minimal DT support for DevKit8000. 2013-03-17 5:23 ` Anil Kumar @ 2013-03-18 15:21 ` Benoit Cousson 0 siblings, 0 replies; 9+ messages in thread From: Benoit Cousson @ 2013-03-18 15:21 UTC (permalink / raw) To: linux-arm-kernel Hi Anil, On 03/17/2013 06:23 AM, Anil Kumar wrote: > Hi Benoit, > > On Thu, Mar 7, 2013 at 12:21 PM, Benoit Cousson <b-cousson@ti.com> wrote: >> Hi, >> >> On 03/06/2013 06:53 PM, Tony Lindgren wrote: >>> * Anil Kumar <anilk4.v@gmail.com> [130305 18:40]: >>>> Hi Tony, >>>> >>>>>> From: linux-arm-kernel [mailto:linux-arm-kernel- >>>>>> bounces at lists.infradead.org] On Behalf Of Anil Kumar >>>>>> Sent: Wednesday, February 27, 2013 8:03 AM >>>>>> To: devicetree-discuss at lists.ozlabs.org; linux-omap at vger.kernel.org; >>>>>> linux-kernel at vger.kernel.org; linux-arm-kernel at lists.infradead.org >>>>>> Cc: linux at arm.linux.org.uk; Cousson, Benoit; Tony Lindgren; Grant >>>>>> Likely; Anil Kumar; thomas at tomweber.eu >>>>>> Subject: Re: FW: [PATCH V4] ARM: dts: add minimal DT support for >>>>>> DevKit8000. >>>>>> >>>>>> Hi, >>>>>>> >>>>>>> DevKit8000 is a beagle board clone from Timll, sold by >>>>>>> armkits.com. The DevKit8000 has RS232 serial port, LCD, DVI-D, >>>>>>> S-Video, Ethernet, SD/MMC, keyboard, camera, SPI, I2C, USB and >>>>>>> JTAG interface. >>>>>>> >>>>>>> This patch adds the basic DT support for devkit8000. At this time, >>>>>> Information >>>>>>> of twl4030 (PMIC), MMC1, I2C1 and leds are added. >>>>>>> >>>>>>> Signed-off-by: Anil Kumar <anilk4.v@gmail.com> >>>>>>> Tested-by: Thomas Weber <thomas@tomweber.eu> >>>>>> >>>>>> Gentle Ping. As there are no review comments on this patch, >>>>>> Could you please pull this patch ? >>>> >>>> Gentle Ping. >>>> >>>> This patch also got Reviewed-by: Manish Badarkhe <badarkhe.manish@gmail.com> >>>> and as patch "ARM: dts: omap3-devkit8000: Enable audio support" has already got >>>> "Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>" but it is on the >>>> top of this patch. >>>> So, Could you please pull this patch in one of your omap branch? or >>>> you want me to >>>> do rebase this patch on top of v3.9-rc1 ? >>> >>> Let's wait for Benoit to queue it as he has a bunch of .dts changesfor_3.10/dts already >>> applied. Too bad we missed v3.9 merge window for those, but hopefully >>> we can get them queued early for v3.10. >> >> Yep, sorry for having missed 3.9, I was a little bit sick at the wrong >> moment :-( >> >> I'm starting queuing the pending patches, and should have enough to push >> to you just after Linaro Connect. > > I think you missed below patch which is needed for gpmc nand to work fine. > > Jon Hunter:- > ARM: OMAP2+: Fix-up gpmc merge error > > I have re based my changes on top of your repository to make pull > easier for you. > I hope you will pull these changes for 3.10. > > The following changes since Commit a7f7881de9c0b58de3b3aea8f01a8aef906d4ade > > are available in the git repository at: > > git://gitorious.org/devkit8000-for_3-10/devkit8000-for_3-10.git > branch for_3.10/dts > > for you to fetch changes up to Commit 975abc8b2e7ec4ff7324d726c9775958945ccc5e Thanks, I pulled the patches and rebased that on top of -rc3 to get the missing fix from Jon. I cleaned as well some changelog / subject and pushed then in my for_3.10/dts branch. Regards, Benoit ^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH V4] ARM: dts: add minimal DT support for DevKit8000 @ 2013-02-20 13:44 Anil Kumar 2013-02-20 15:02 ` Manish Badarkhe 0 siblings, 1 reply; 9+ messages in thread From: Anil Kumar @ 2013-02-20 13:44 UTC (permalink / raw) To: linux-arm-kernel DevKit8000 is a beagle board clone from Timll, sold by armkits.com. The DevKit8000 has RS232 serial port, LCD, DVI-D, S-Video, Ethernet, SD/MMC, keyboard, camera, SPI, I2C, USB and JTAG interface. This patch adds the basic DT support for devkit8000. At this time, Information of twl4030 (PMIC), MMC1, I2C1 and leds are added. Signed-off-by: Anil Kumar <anilk4.v@gmail.com> Tested-by: Thomas Weber <thomas@tomweber.eu> --- -This patch is based on top of kernel 3.8-rc5. -Tested on Devkit8000. For V4: -Tiny nitpick. For V3: - Remove pin mux as done at device boot time by default. For V2: - Change model name as "TimLL OMAP3 Devkit8000" - Change compatible as "timll,omap3-devkit8000" - Doing i2c1 pinmux default with pinctrl-single driver instead of i2c1 driver probe time. :100644 100644 5ebb44f... 22ebc76... M arch/arm/boot/dts/Makefile :000000 100644 0000000... 2e1463a... A arch/arm/boot/dts/omap3-devkit8000.dts :100644 100644 53cb380b.. ccecb76... M arch/arm/mach-omap2/board-generic.c arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/omap3-devkit8000.dts | 102 ++++++++++++++++++++++++++++++++ arch/arm/mach-omap2/board-generic.c | 1 + 3 files changed, 104 insertions(+), 0 deletions(-) diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 5ebb44f..22ebc76 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -102,6 +102,7 @@ dtb-$(CONFIG_ARCH_MXS) += imx23-evk.dtb \ imx28-tx28.dtb dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \ omap3-beagle.dtb \ + omap3-devkit8000.dtb \ omap3-beagle-xm.dtb \ omap3-evm.dtb \ omap3-tobi.dtb \ diff --git a/arch/arm/boot/dts/omap3-devkit8000.dts b/arch/arm/boot/dts/omap3-devkit8000.dts new file mode 100644 index 0000000..2e1463a --- /dev/null +++ b/arch/arm/boot/dts/omap3-devkit8000.dts @@ -0,0 +1,102 @@ +/* + * Author: Anil Kumar <anilk4.v@gmail.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +/include/ "omap3.dtsi" +/ { + model = "TimLL OMAP3 Devkit8000"; + compatible = "timll,omap3-devkit8000", "ti,omap3"; + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; /* 256 MB */ + }; + + leds { + compatible = "gpio-leds"; + + heartbeat { + label = "devkit8000::led1"; + gpios = <&gpio6 26 0>; /* 186 -> LED1 */ + default-state = "on"; + linux,default-trigger = "heartbeat"; + }; + + mmc { + label = "devkit8000::led2"; + gpios = <&gpio6 3 0>; /* 163 -> LED2 */ + default-state = "on"; + linux,default-trigger = "none"; + }; + + usr { + label = "devkit8000::led3"; + gpios = <&gpio6 4 0>; /* 164 -> LED3 */ + default-state = "on"; + linux,default-trigger = "usr"; + }; + }; +}; + +&i2c1 { + clock-frequency = <2600000>; + + twl: twl at 48 { + reg = <0x48>; + interrupts = <7>; /* SYS_NIRQ cascaded to intc */ + interrupt-parent = <&intc>; + }; +}; + +&i2c2 { + status = "disabled"; +}; + +&i2c3 { + status = "disabled"; +}; + +/include/ "twl4030.dtsi" + +&mmc1 { + vmmc-supply = <&vmmc1>; + vmmc_aux-supply = <&vsim>; + bus-width = <8>; +}; + +&mmc2 { + status = "disabled"; +}; + +&mmc3 { + status = "disabled"; +}; + +&wdt2 { + status = "disabled"; +}; + +&mcbsp1 { + status = "disabled"; +}; + +&mcbsp2 { + status = "disabled"; +}; + +&mcbsp3 { + status = "disabled"; +}; + +&mcbsp4 { + status = "disabled"; +}; + +&mcbsp5 { + status = "disabled"; +}; diff --git a/arch/arm/mach-omap2/board-generic.c b/arch/arm/mach-omap2/board-generic.c index 53cb380..ccecb76 100644 --- a/arch/arm/mach-omap2/board-generic.c +++ b/arch/arm/mach-omap2/board-generic.c @@ -110,6 +110,7 @@ MACHINE_END static const char *omap3_gp_boards_compat[] __initdata = { "ti,omap3-beagle", + "timll,omap3-devkit8000", NULL, }; -- 1.7.0.4 ^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH V4] ARM: dts: add minimal DT support for DevKit8000 2013-02-20 13:44 Anil Kumar @ 2013-02-20 15:02 ` Manish Badarkhe 0 siblings, 0 replies; 9+ messages in thread From: Manish Badarkhe @ 2013-02-20 15:02 UTC (permalink / raw) To: linux-arm-kernel Hi Anil On Wed, Feb 20, 2013 at 7:14 PM, Anil Kumar <anilk4.v@gmail.com> wrote: > DevKit8000 is a beagle board clone from Timll, sold by > armkits.com. The DevKit8000 has RS232 serial port, LCD, DVI-D, > S-Video, Ethernet, SD/MMC, keyboard, camera, SPI, I2C, USB and > JTAG interface. > > This patch adds the basic DT support for devkit8000. At this time, Information > of twl4030 (PMIC), MMC1, I2C1 and leds are added. > > Signed-off-by: Anil Kumar <anilk4.v@gmail.com> > Tested-by: Thomas Weber <thomas@tomweber.eu> > --- > -This patch is based on top of kernel 3.8-rc5. > > -Tested on Devkit8000. > > For V4: > -Tiny nitpick. > > For V3: > - Remove pin mux as done at device boot time by default. > > For V2: > - Change model name as "TimLL OMAP3 Devkit8000" > - Change compatible as "timll,omap3-devkit8000" > - Doing i2c1 pinmux default with pinctrl-single driver instead of i2c1 > driver probe time. > > :100644 100644 5ebb44f... 22ebc76... M arch/arm/boot/dts/Makefile > :000000 100644 0000000... 2e1463a... A arch/arm/boot/dts/omap3-devkit8000.dts > :100644 100644 53cb380b.. ccecb76... M arch/arm/mach-omap2/board-generic.c > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/omap3-devkit8000.dts | 102 ++++++++++++++++++++++++++++++++ > arch/arm/mach-omap2/board-generic.c | 1 + > 3 files changed, 104 insertions(+), 0 deletions(-) > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index 5ebb44f..22ebc76 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -102,6 +102,7 @@ dtb-$(CONFIG_ARCH_MXS) += imx23-evk.dtb \ > imx28-tx28.dtb > dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \ > omap3-beagle.dtb \ > + omap3-devkit8000.dtb \ > omap3-beagle-xm.dtb \ > omap3-evm.dtb \ > omap3-tobi.dtb \ > diff --git a/arch/arm/boot/dts/omap3-devkit8000.dts b/arch/arm/boot/dts/omap3-devkit8000.dts > new file mode 100644 > index 0000000..2e1463a > --- /dev/null > +++ b/arch/arm/boot/dts/omap3-devkit8000.dts > @@ -0,0 +1,102 @@ > +/* > + * Author: Anil Kumar <anilk4.v@gmail.com> > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > + */ > +/dts-v1/; > + > +/include/ "omap3.dtsi" > +/ { > + model = "TimLL OMAP3 Devkit8000"; > + compatible = "timll,omap3-devkit8000", "ti,omap3"; > + > + memory { > + device_type = "memory"; > + reg = <0x80000000 0x10000000>; /* 256 MB */ > + }; > + > + leds { > + compatible = "gpio-leds"; > + > + heartbeat { > + label = "devkit8000::led1"; > + gpios = <&gpio6 26 0>; /* 186 -> LED1 */ > + default-state = "on"; > + linux,default-trigger = "heartbeat"; > + }; > + > + mmc { > + label = "devkit8000::led2"; > + gpios = <&gpio6 3 0>; /* 163 -> LED2 */ > + default-state = "on"; > + linux,default-trigger = "none"; > + }; > + > + usr { > + label = "devkit8000::led3"; > + gpios = <&gpio6 4 0>; /* 164 -> LED3 */ > + default-state = "on"; > + linux,default-trigger = "usr"; > + }; > + }; > +}; > + > +&i2c1 { > + clock-frequency = <2600000>; > + > + twl: twl at 48 { > + reg = <0x48>; > + interrupts = <7>; /* SYS_NIRQ cascaded to intc */ > + interrupt-parent = <&intc>; > + }; > +}; > + > +&i2c2 { > + status = "disabled"; > +}; > + > +&i2c3 { > + status = "disabled"; > +}; > + > +/include/ "twl4030.dtsi" > + > +&mmc1 { > + vmmc-supply = <&vmmc1>; > + vmmc_aux-supply = <&vsim>; > + bus-width = <8>; > +}; > + > +&mmc2 { > + status = "disabled"; > +}; > + > +&mmc3 { > + status = "disabled"; > +}; > + > +&wdt2 { > + status = "disabled"; > +}; > + > +&mcbsp1 { > + status = "disabled"; > +}; > + > +&mcbsp2 { > + status = "disabled"; > +}; > + > +&mcbsp3 { > + status = "disabled"; > +}; > + > +&mcbsp4 { > + status = "disabled"; > +}; > + > +&mcbsp5 { > + status = "disabled"; > +}; > diff --git a/arch/arm/mach-omap2/board-generic.c b/arch/arm/mach-omap2/board-generic.c > index 53cb380..ccecb76 100644 > --- a/arch/arm/mach-omap2/board-generic.c > +++ b/arch/arm/mach-omap2/board-generic.c > @@ -110,6 +110,7 @@ MACHINE_END > > static const char *omap3_gp_boards_compat[] __initdata = { > "ti,omap3-beagle", > + "timll,omap3-devkit8000", > NULL, > }; > Looks good to me. Reviewed-by: Manish Badarkhe <badarkhe.manish@gmail.com> Thanks Manish Badarkhe ^ permalink raw reply [flat|nested] 9+ messages in thread
end of thread, other threads:[~2013-03-18 15:21 UTC | newest]
Thread overview: 9+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
[not found] <F3DBB1B3EF102E4994C89758CFCA32412CC4E9@DBDE01.ent.ti.com>
2013-02-27 2:33 ` FW: [PATCH V4] ARM: dts: add minimal DT support for DevKit8000 Anil Kumar
[not found] ` <F3DBB1B3EF102E4994C89758CFCA32412CC74F@DBDE01.ent.ti.com>
2013-03-06 2:36 ` Anil Kumar
2013-03-06 17:53 ` Tony Lindgren
2013-03-07 6:51 ` Benoit Cousson
2013-03-07 16:10 ` Tony Lindgren
2013-03-17 5:23 ` Anil Kumar
2013-03-18 15:21 ` Benoit Cousson
2013-02-20 13:44 Anil Kumar
2013-02-20 15:02 ` Manish Badarkhe
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).