[PATCH 1/7] ARM: dts: sun4i: Enable tablet keys on Chuwi V7 CW0825

[PATCH 1/7] ARM: dts: sun4i: Enable tablet keys on Chuwi V7 CW0825

[Hans de Goede]

Enable the lradc controlled tablet keys on the Chuwi V7 CW0825 tablet.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
 arch/arm/boot/dts/sun4i-a10-chuwi-v7-cw0825.dts | 27 +++++++++++++++++++++++++
 1 file changed, 27 insertions(+)

diff --git a/arch/arm/boot/dts/sun4i-a10-chuwi-v7-cw0825.dts b/arch/arm/boot/dts/sun4i-a10-chuwi-v7-cw0825.dts
index 58214f2..97fca89 100644
--- a/arch/arm/boot/dts/sun4i-a10-chuwi-v7-cw0825.dts
+++ b/arch/arm/boot/dts/sun4i-a10-chuwi-v7-cw0825.dts
@@ -49,6 +49,7 @@
 #include "sun4i-a10.dtsi"
 #include "sunxi-common-regulators.dtsi"
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
 
 / {
 	model = "Chuwi V7 CW0825";
@@ -74,6 +75,32 @@
 	};
 };
 
+&lradc {
+	vref-supply = <&reg_vcc3v0>;
+	status = "okay";
+
+	button at 800 {
+		label = "Volume Up";
+		linux,code = <KEY_VOLUMEUP>;
+		channel = <0>;
+		voltage = <800000>;
+	};
+
+	button at 1000 {
+		label = "Volume Down";
+		linux,code = <KEY_VOLUMEDOWN>;
+		channel = <0>;
+		voltage = <1000000>;
+	};
+
+	button at 1200 {
+		label = "Back";
+		linux,code = <KEY_BACK>;
+		channel = <0>;
+		voltage = <1200000>;
+	};
+};
+
 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
-- 
2.3.1

[PATCH 2/7] ARM: dts: sun5i: Stop using different compatibles for ehci/ohci on a13 vs a10s

[Hans de Goede]

The A13 and the A10s use the same die (this has been confirmed by Allwinner),
as such there is no need to differentiate between the ehci/ohci parts of both,
the only reasons there were different allwinner,sun5i-a*-foo compatible
between these 2 parts is costemetically and because we could when we still
had 2 completely different dtsi files.

The allwinner,sun5i-a*-foo compatible strings are not used for binding at all,
the actual driver binds to the generic-?hci compatible, so we can safely remove
this cosmetical difference and simplify the dtsi files.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
 arch/arm/boot/dts/sun5i-a10s.dtsi | 8 --------
 arch/arm/boot/dts/sun5i-a13.dtsi  | 8 --------
 arch/arm/boot/dts/sun5i.dtsi      | 2 ++
 3 files changed, 2 insertions(+), 16 deletions(-)

diff --git a/arch/arm/boot/dts/sun5i-a10s.dtsi b/arch/arm/boot/dts/sun5i-a10s.dtsi
index ef516db..a78c95d 100644
--- a/arch/arm/boot/dts/sun5i-a10s.dtsi
+++ b/arch/arm/boot/dts/sun5i-a10s.dtsi
@@ -157,14 +157,6 @@
 	};
 };
 
-&ehci0 {
-	compatible = "allwinner,sun5i-a10s-ehci", "generic-ehci";
-};
-
-&ohci0 {
-	compatible = "allwinner,sun5i-a10s-ohci", "generic-ohci";
-};
-
 &pio {
 	compatible = "allwinner,sun5i-a10s-pinctrl";
 
diff --git a/arch/arm/boot/dts/sun5i-a13.dtsi b/arch/arm/boot/dts/sun5i-a13.dtsi
index 5d9ce84..136158f 100644
--- a/arch/arm/boot/dts/sun5i-a13.dtsi
+++ b/arch/arm/boot/dts/sun5i-a13.dtsi
@@ -153,14 +153,6 @@
 	cooling-max-level = <6>;
 };
 
-&ehci0 {
-	compatible = "allwinner,sun5i-a13-ehci", "generic-ehci";
-};
-
-&ohci0 {
-	compatible = "allwinner,sun5i-a13-ohci", "generic-ohci";
-};
-
 &pio {
 	compatible = "allwinner,sun5i-a13-pinctrl";
 
diff --git a/arch/arm/boot/dts/sun5i.dtsi b/arch/arm/boot/dts/sun5i.dtsi
index 610ea18..416c4de 100644
--- a/arch/arm/boot/dts/sun5i.dtsi
+++ b/arch/arm/boot/dts/sun5i.dtsi
@@ -392,6 +392,7 @@
 		};
 
 		ehci0: usb at 01c14000 {
+			compatible = "allwinner,sun5i-a13-ehci", "generic-ehci";
 			reg = <0x01c14000 0x100>;
 			interrupts = <39>;
 			clocks = <&ahb_gates 1>;
@@ -401,6 +402,7 @@
 		};
 
 		ohci0: usb at 01c14400 {
+			compatible = "allwinner,sun5i-a13-ohci", "generic-ohci";
 			reg = <0x01c14400 0x100>;
 			interrupts = <40>;
 			clocks = <&usb_clk 6>, <&ahb_gates 2>;
-- 
2.3.1

[PATCH 3/7] ARM: dts: sun5i: Add mmc2 pinmux settings

[Hans de Goede]

Add A13 mmc2 pinmux settings, note these are for a 8bit bus.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
 arch/arm/boot/dts/sun5i.dtsi | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/arch/arm/boot/dts/sun5i.dtsi b/arch/arm/boot/dts/sun5i.dtsi
index 416c4de..244d896 100644
--- a/arch/arm/boot/dts/sun5i.dtsi
+++ b/arch/arm/boot/dts/sun5i.dtsi
@@ -469,6 +469,15 @@
 				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
 				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
 			};
+
+			mmc2_pins_a: mmc2 at 0 {
+				allwinner,pins = "PC6", "PC7", "PC8", "PC9",
+					"PC10", "PC11", "PC12", "PC13",
+					"PC14", "PC15";
+				allwinner,function = "mmc2";
+				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+			};
 		};
 
 		timer at 01c20c00 {
-- 
2.3.1

[PATCH 4/7] ARM: dts: sun5i: Add new Auxtek-t004 board

[Hans de Goede]

The auxtek-t004:
http://www.fasttech.com/products/1110/10004200/1318603-auxtek-t004-allwinner-a10s-single-core-android-ics

Is an Allwinner A10s based hdmi tv stick with with 512M RAM, 4G nand flash,
toc9002 (bcm43362) sdio wifi, 1 USB host ports using an USB-A receptacle and
a 2 micro-usb receptacles, one for power and one for USB OTG.

The sdio wifi appears to not have an oob irq hooked up, so we rely on sdio-irq
support for it.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>

foo
---
 arch/arm/boot/dts/Makefile                   |   1 +
 arch/arm/boot/dts/sun5i-a10s-auxtek-t004.dts | 151 +++++++++++++++++++++++++++
 2 files changed, 152 insertions(+)
 create mode 100644 arch/arm/boot/dts/sun5i-a10s-auxtek-t004.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index beac15f..d824336 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -525,6 +525,7 @@ dtb-$(CONFIG_MACH_SUN4I) += \
 	sun4i-a10-olinuxino-lime.dtb \
 	sun4i-a10-pcduino.dtb
 dtb-$(CONFIG_MACH_SUN5I) += \
+	sun5i-a10s-auxtek-t004.dtb \
 	sun5i-a10s-mk802.dtb \
 	sun5i-a10s-olinuxino-micro.dtb \
 	sun5i-a10s-r7-tv-dongle.dtb \
diff --git a/arch/arm/boot/dts/sun5i-a10s-auxtek-t004.dts b/arch/arm/boot/dts/sun5i-a10s-auxtek-t004.dts
new file mode 100644
index 0000000..6c6fef7
--- /dev/null
+++ b/arch/arm/boot/dts/sun5i-a10s-auxtek-t004.dts
@@ -0,0 +1,151 @@
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ *     You should have received a copy of the GNU General Public
+ *     License along with this file; if not, write to the Free
+ *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ *     MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun5i-a10s.dtsi"
+#include "sunxi-common-regulators.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+	model = "Auxtek t004 A10s hdmi tv-stick";
+	compatible = "allwinner,auxtek-t004", "allwinner,sun5i-a10s";
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pins_t004>;
+
+		red {
+			label = "t004-tv-dongle:red:usr";
+			gpios = <&pio 1 2 GPIO_ACTIVE_HIGH>; /* PB2 */
+			default-state = "on";
+		};
+	};
+
+	reg_vmmc1: vmmc1 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&mmc1_vcc_en_pin_t004>;
+		regulator-name = "vmmc1";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		gpio = <&pio 1 18 GPIO_ACTIVE_HIGH>; /* PB18 */
+	};
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_t004>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
+	cd-inverted;
+	status = "okay";
+};
+
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins_a>;
+	vmmc-supply = <&reg_vmmc1>;
+	bus-width = <4>;
+	non-removable;
+	cap-sdio-irq;
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&pio {
+	mmc0_cd_pin_t004: mmc0_cd_pin at 0 {
+		allwinner,pins = "PG1";
+		allwinner,function = "gpio_in";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+	};
+
+	mmc1_vcc_en_pin_t004: mmc1_vcc_en_pin at 0 {
+		allwinner,pins = "PB18";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+
+	led_pins_t004: led_pins at 0 {
+		allwinner,pins = "PB2";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_20_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+};
+
+&reg_usb1_vbus {
+	gpio = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};
+
+&usb1_vbus_pin_a {
+	allwinner,pins = "PG13";
+};
+
+&usbphy {
+	usb1_vbus-supply = <&reg_usb1_vbus>;
+	status = "okay";
+};
-- 
2.3.1

[PATCH 5/7] ARM: dts: sun5i: Add new Utoo P66 board

[Hans de Goede]

The UTOO P66 is a 6" A13 tablet / lcd ereader. It features a 6" 480x800 ips
lcd screen, 512MB RAM & 4GB emmc.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
 arch/arm/boot/dts/Makefile               |   3 +-
 arch/arm/boot/dts/sun5i-a13-utoo-p66.dts | 203 +++++++++++++++++++++++++++++++
 2 files changed, 205 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/boot/dts/sun5i-a13-utoo-p66.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index d824336..f97c5d3 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -531,7 +531,8 @@ dtb-$(CONFIG_MACH_SUN5I) += \
 	sun5i-a10s-r7-tv-dongle.dtb \
 	sun5i-a13-hsg-h702.dtb \
 	sun5i-a13-olinuxino.dtb \
-	sun5i-a13-olinuxino-micro.dtb
+	sun5i-a13-olinuxino-micro.dtb \
+	sun5i-a13-utoo-p66.dtb
 dtb-$(CONFIG_MACH_SUN6I) += \
 	sun6i-a31-app4-evb1.dtb \
 	sun6i-a31-colombus.dtb \
diff --git a/arch/arm/boot/dts/sun5i-a13-utoo-p66.dts b/arch/arm/boot/dts/sun5i-a13-utoo-p66.dts
new file mode 100644
index 0000000..0f0a411
--- /dev/null
+++ b/arch/arm/boot/dts/sun5i-a13-utoo-p66.dts
@@ -0,0 +1,203 @@
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ *     You should have received a copy of the GNU General Public
+ *     License along with this file; if not, write to the Free
+ *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ *     MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun5i-a13.dtsi"
+#include "sunxi-common-regulators.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+	model = "Utoo P66";
+	compatible = "utoo,p66", "allwinner,sun5i-a13";
+
+	i2c_lcd: i2c at 0 {
+		/* The lcd panel i2c interface is hooked up via gpios */
+		compatible = "i2c-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_lcd_pins>;
+		gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>, /* PG12, sda */
+			<&pio 6 10 GPIO_ACTIVE_HIGH>; /* PG10, scl */
+		i2c-gpio,delay-us = <5>;
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+
+	axp209: pmic at 34 {
+		reg = <0x34>;
+		interrupts = <0>;
+	};
+};
+
+#include "axp209.dtsi"
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins_a>;
+	status = "okay";
+
+	pcf8563: rtc at 51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+};
+
+&lradc {
+	vref-supply = <&reg_ldo2>;
+	status = "okay";
+
+	button at 200 {
+		label = "Volume Up";
+		linux,code = <KEY_VOLUMEUP>;
+		channel = <0>;
+		voltage = <200000>;
+	};
+
+	button at 400 {
+		label = "Volume Down";
+		linux,code = <KEY_VOLUMEDOWN>;
+		channel = <0>;
+		voltage = <400000>;
+	};
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_p66>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */
+	cd-inverted;
+	status = "okay";
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins_a>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&pio {
+	mmc0_cd_pin_p66: mmc0_cd_pin at 0 {
+		allwinner,pins = "PG0";
+		allwinner,function = "gpio_in";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+	};
+
+	i2c_lcd_pins: i2c_lcd_pin at 0 {
+		allwinner,pins = "PG10", "PG12";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+	};
+
+	usb0_vbus_pin_a: usb0_vbus_pin at 0 {
+		allwinner,pins = "PB4";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1500000>;
+	regulator-name = "vdd-cpu";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-int-pll";
+};
+
+&reg_ldo1 {
+	regulator-name = "vdd-rtc";
+};
+
+&reg_ldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "avcc";
+};
+
+&reg_ldo3 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi";
+};
+
+&reg_usb0_vbus {
+	gpio = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
+	status = "okay";
+};
+
+&usbphy {
+	usb0_vbus-supply = <&reg_usb0_vbus>;
+	usb1_vbus-supply = <&reg_ldo3>;
+	status = "okay";
+};
-- 
2.3.1

[PATCH 6/7] ARM: dts: sun7i: Add OOB irq support to boards with broadcom sdio wifi

[Hans de Goede]

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
 arch/arm/boot/dts/sun7i-a20-cubietruck.dts | 11 +++++++++++
 arch/arm/boot/dts/sun7i-a20-i12-tvbox.dts  | 11 +++++++++++
 2 files changed, 22 insertions(+)

diff --git a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts
index 0c219a4..8111b0c 100644
--- a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts
+++ b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts
@@ -167,12 +167,23 @@
 };
 
 &mmc3 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc3_pins_a>;
 	vmmc-supply = <&reg_vmmc3>;
 	bus-width = <4>;
 	non-removable;
 	status = "okay";
+
+	brcmf: bcrmf at 1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&pio>;
+		interrupts = <10 8>; /* PH10 / EINT10 */
+		interrupt-names = "host-wake";
+	};
 };
 
 &mmc3_pins_a {
diff --git a/arch/arm/boot/dts/sun7i-a20-i12-tvbox.dts b/arch/arm/boot/dts/sun7i-a20-i12-tvbox.dts
index baee563..4a8defd 100644
--- a/arch/arm/boot/dts/sun7i-a20-i12-tvbox.dts
+++ b/arch/arm/boot/dts/sun7i-a20-i12-tvbox.dts
@@ -164,12 +164,23 @@
 };
 
 &mmc3 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc3_pins_a>;
 	vmmc-supply = <&reg_vmmc3>;
 	bus-width = <4>;
 	non-removable;
 	status = "okay";
+
+	brcmf: bcrmf at 1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&pio>;
+		interrupts = <10 8>; /* PH10 / EINT10 */
+		interrupt-names = "host-wake";
+	};
 };
 
 &mmc3_pins_a {
-- 
2.3.1

[PATCH 7/7] ARM: dts: sun7i: Enable cap-sdio-irq for bananapro sdio wifi

[Hans de Goede]

The sdio wifi on the Banana Pro does not appear to have an oob irq hooked
up, so enable sdio-irq support to avoid unnecessary polling.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
 arch/arm/boot/dts/sun7i-a20-bananapro.dts | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/boot/dts/sun7i-a20-bananapro.dts b/arch/arm/boot/dts/sun7i-a20-bananapro.dts
index fb89fe7..d0cd78f 100644
--- a/arch/arm/boot/dts/sun7i-a20-bananapro.dts
+++ b/arch/arm/boot/dts/sun7i-a20-bananapro.dts
@@ -164,6 +164,7 @@
 	vmmc-supply = <&reg_vmmc3>;
 	bus-width = <4>;
 	non-removable;
+	cap-sdio-irq;
 	status = "okay";
 };
 
-- 
2.3.1

[linux-sunxi] [PATCH 6/7] ARM: dts: sun7i: Add OOB irq support to boards with broadcom sdio wifi

[Chen-Yu Tsai]

Hi,

On Sun, Mar 8, 2015 at 3:01 AM, Hans de Goede <hdegoede@redhat.com> wrote:
> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
> ---
>  arch/arm/boot/dts/sun7i-a20-cubietruck.dts | 11 +++++++++++
>  arch/arm/boot/dts/sun7i-a20-i12-tvbox.dts  | 11 +++++++++++
>  2 files changed, 22 insertions(+)
>
> diff --git a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts
> index 0c219a4..8111b0c 100644
> --- a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts
> +++ b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts
> @@ -167,12 +167,23 @@
>  };
>
>  &mmc3 {
> +       #address-cells = <1>;
> +       #size-cells = <0>;
> +
>         pinctrl-names = "default";
>         pinctrl-0 = <&mmc3_pins_a>;
>         vmmc-supply = <&reg_vmmc3>;
>         bus-width = <4>;
>         non-removable;
>         status = "okay";
> +
> +       brcmf: bcrmf at 1 {
> +               reg = <1>;
> +               compatible = "brcm,bcm4329-fmac";
> +               interrupt-parent = <&pio>;
> +               interrupts = <10 8>; /* PH10 / EINT10 */
                                   ^ IRQ_TYPE_LEVEL_LOW?

> +               interrupt-names = "host-wake";
> +       };
>  };
>
>  &mmc3_pins_a {
> diff --git a/arch/arm/boot/dts/sun7i-a20-i12-tvbox.dts b/arch/arm/boot/dts/sun7i-a20-i12-tvbox.dts
> index baee563..4a8defd 100644
> --- a/arch/arm/boot/dts/sun7i-a20-i12-tvbox.dts
> +++ b/arch/arm/boot/dts/sun7i-a20-i12-tvbox.dts
> @@ -164,12 +164,23 @@
>  };
>
>  &mmc3 {
> +       #address-cells = <1>;
> +       #size-cells = <0>;
> +
>         pinctrl-names = "default";
>         pinctrl-0 = <&mmc3_pins_a>;
>         vmmc-supply = <&reg_vmmc3>;
>         bus-width = <4>;
>         non-removable;
>         status = "okay";
> +
> +       brcmf: bcrmf at 1 {
> +               reg = <1>;
> +               compatible = "brcm,bcm4329-fmac";
> +               interrupt-parent = <&pio>;
> +               interrupts = <10 8>; /* PH10 / EINT10 */

Same here.

ChenYu

> +               interrupt-names = "host-wake";
> +       };
>  };
>
>  &mmc3_pins_a {

[linux-sunxi] [PATCH 7/7] ARM: dts: sun7i: Enable cap-sdio-irq for bananapro sdio wifi

[Chen-Yu Tsai]

On Sun, Mar 8, 2015 at 3:01 AM, Hans de Goede <hdegoede@redhat.com> wrote:
> The sdio wifi on the Banana Pro does not appear to have an oob irq hooked
> up, so enable sdio-irq support to avoid unnecessary polling.

I wonder if this is stable enough to put back into the mmc driver, i.e.
declare the capability in the driver itself? IIRC at one point it did.

ChenYu

> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
> ---
>  arch/arm/boot/dts/sun7i-a20-bananapro.dts | 1 +
>  1 file changed, 1 insertion(+)
>
> diff --git a/arch/arm/boot/dts/sun7i-a20-bananapro.dts b/arch/arm/boot/dts/sun7i-a20-bananapro.dts
> index fb89fe7..d0cd78f 100644
> --- a/arch/arm/boot/dts/sun7i-a20-bananapro.dts
> +++ b/arch/arm/boot/dts/sun7i-a20-bananapro.dts
> @@ -164,6 +164,7 @@
>         vmmc-supply = <&reg_vmmc3>;
>         bus-width = <4>;
>         non-removable;
> +       cap-sdio-irq;
>         status = "okay";
>  };
>
> --
> 2.3.1

[linux-sunxi] [PATCH 6/7] ARM: dts: sun7i: Add OOB irq support to boards with broadcom sdio wifi

[Chen-Yu Tsai]

On Sun, Mar 8, 2015 at 3:01 AM, Hans de Goede <hdegoede@redhat.com> wrote:
> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
> ---
>  arch/arm/boot/dts/sun7i-a20-cubietruck.dts | 11 +++++++++++
>  arch/arm/boot/dts/sun7i-a20-i12-tvbox.dts  | 11 +++++++++++
>  2 files changed, 22 insertions(+)
>
> diff --git a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts
> index 0c219a4..8111b0c 100644
> --- a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts
> +++ b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts
> @@ -167,12 +167,23 @@
>  };
>
>  &mmc3 {
> +       #address-cells = <1>;
> +       #size-cells = <0>;
> +
>         pinctrl-names = "default";
>         pinctrl-0 = <&mmc3_pins_a>;
>         vmmc-supply = <&reg_vmmc3>;
>         bus-width = <4>;
>         non-removable;
>         status = "okay";
> +
> +       brcmf: bcrmf at 1 {
> +               reg = <1>;
> +               compatible = "brcm,bcm4329-fmac";
> +               interrupt-parent = <&pio>;
> +               interrupts = <10 8>; /* PH10 / EINT10 */
> +               interrupt-names = "host-wake";
> +       };

I gave this a spin on my Cubietruck. (I was running cap-sdio-irq before.)

Ran a few ping tests with a simple
"sudo ping -i 0.1 -I wlan0 -s 65500 192.168.1.1"
After a few runs I got

sunxi-mmc 1c12000.mmc: smc 1 err, cmd 53, RD SBE !!
sunxi-mmc 1c12000.mmc: data error, sending stop command
brcmfmac: brcmf_sdio_readframes: RXHEADER FAILED: -110
brcmfmac: brcmf_sdio_rxfail: abort command, terminate frame, send NAK
brcmfmac: brcmf_sdiod_regrw_helper: failed to write data F1 at 0x0a040, err: -5
brcmfmac: brcmf_sdio_hdparse: seq 226: sequence number error, expect 227
sunxi-mmc 1c12000.mmc: smc 1 err, cmd 53, RD DTO !!
sunxi-mmc 1c12000.mmc: data error, sending stop command
sunxi-mmc 1c12000.mmc: smc 1 err, cmd 53, RD DTO !!
sunxi-mmc 1c12000.mmc: data error, sending stop command
sunxi-mmc 1c12000.mmc: smc 1 err, cmd 53, RD DTO !!
sunxi-mmc 1c12000.mmc: data error, sending stop command
brcmfmac: brcmf_sdiod_regrw_helper: failed to read data F1 at 0x0a020, err: -110
brcmfmac: brcmf_sdio_dpc: failed backplane access over SDIO, halting operation
sunxi-mmc 1c12000.mmc: smc 1 err, cmd 53, RD DTO !!
sunxi-mmc 1c12000.mmc: data error, sending stop command
sunxi-mmc 1c12000.mmc: smc 1 err, cmd 53, RD DTO !!
sunxi-mmc 1c12000.mmc: data error, sending stop command
sunxi-mmc 1c12000.mmc: smc 1 err, cmd 53, RD DTO !!
sunxi-mmc 1c12000.mmc: data error, sending stop command

The chip is pretty much dead afterwards.

With cap-sdio-irq it doesn't happen so soon, but it does.
Without either, the response time is bad with packet losses,
but at least it doesn't die.

Is this the problem Arend (CC-ed) was looking into?

Regards
ChenYu

>  };
>
>  &mmc3_pins_a {
> diff --git a/arch/arm/boot/dts/sun7i-a20-i12-tvbox.dts b/arch/arm/boot/dts/sun7i-a20-i12-tvbox.dts
> index baee563..4a8defd 100644
> --- a/arch/arm/boot/dts/sun7i-a20-i12-tvbox.dts
> +++ b/arch/arm/boot/dts/sun7i-a20-i12-tvbox.dts
> @@ -164,12 +164,23 @@
>  };
>
>  &mmc3 {
> +       #address-cells = <1>;
> +       #size-cells = <0>;
> +
>         pinctrl-names = "default";
>         pinctrl-0 = <&mmc3_pins_a>;
>         vmmc-supply = <&reg_vmmc3>;
>         bus-width = <4>;
>         non-removable;
>         status = "okay";
> +
> +       brcmf: bcrmf at 1 {
> +               reg = <1>;
> +               compatible = "brcm,bcm4329-fmac";
> +               interrupt-parent = <&pio>;
> +               interrupts = <10 8>; /* PH10 / EINT10 */
> +               interrupt-names = "host-wake";
> +       };
>  };
>
>  &mmc3_pins_a {
> --
> 2.3.1
>
> --
> You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
> To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe at googlegroups.com.
> For more options, visit https://groups.google.com/d/optout.

[linux-sunxi] [PATCH 6/7] ARM: dts: sun7i: Add OOB irq support to boards with broadcom sdio wifi

[Hans de Goede]

Hi,

On 08-03-15 04:12, Chen-Yu Tsai wrote:
> On Sun, Mar 8, 2015 at 3:01 AM, Hans de Goede <hdegoede@redhat.com> wrote:
>> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
>> ---
>>   arch/arm/boot/dts/sun7i-a20-cubietruck.dts | 11 +++++++++++
>>   arch/arm/boot/dts/sun7i-a20-i12-tvbox.dts  | 11 +++++++++++
>>   2 files changed, 22 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts
>> index 0c219a4..8111b0c 100644
>> --- a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts
>> +++ b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts
>> @@ -167,12 +167,23 @@
>>   };
>>
>>   &mmc3 {
>> +       #address-cells = <1>;
>> +       #size-cells = <0>;
>> +
>>          pinctrl-names = "default";
>>          pinctrl-0 = <&mmc3_pins_a>;
>>          vmmc-supply = <&reg_vmmc3>;
>>          bus-width = <4>;
>>          non-removable;
>>          status = "okay";
>> +
>> +       brcmf: bcrmf at 1 {
>> +               reg = <1>;
>> +               compatible = "brcm,bcm4329-fmac";
>> +               interrupt-parent = <&pio>;
>> +               interrupts = <10 8>; /* PH10 / EINT10 */
>> +               interrupt-names = "host-wake";
>> +       };
>
> I gave this a spin on my Cubietruck. (I was running cap-sdio-irq before.)
>
> Ran a few ping tests with a simple
> "sudo ping -i 0.1 -I wlan0 -s 65500 192.168.1.1"
> After a few runs I got
>
> sunxi-mmc 1c12000.mmc: smc 1 err, cmd 53, RD SBE !!
> sunxi-mmc 1c12000.mmc: data error, sending stop command
> brcmfmac: brcmf_sdio_readframes: RXHEADER FAILED: -110
> brcmfmac: brcmf_sdio_rxfail: abort command, terminate frame, send NAK
> brcmfmac: brcmf_sdiod_regrw_helper: failed to write data F1 at 0x0a040, err: -5
> brcmfmac: brcmf_sdio_hdparse: seq 226: sequence number error, expect 227
> sunxi-mmc 1c12000.mmc: smc 1 err, cmd 53, RD DTO !!
> sunxi-mmc 1c12000.mmc: data error, sending stop command
> sunxi-mmc 1c12000.mmc: smc 1 err, cmd 53, RD DTO !!
> sunxi-mmc 1c12000.mmc: data error, sending stop command
> sunxi-mmc 1c12000.mmc: smc 1 err, cmd 53, RD DTO !!
> sunxi-mmc 1c12000.mmc: data error, sending stop command
> brcmfmac: brcmf_sdiod_regrw_helper: failed to read data F1 at 0x0a020, err: -110
> brcmfmac: brcmf_sdio_dpc: failed backplane access over SDIO, halting operation
> sunxi-mmc 1c12000.mmc: smc 1 err, cmd 53, RD DTO !!
> sunxi-mmc 1c12000.mmc: data error, sending stop command
> sunxi-mmc 1c12000.mmc: smc 1 err, cmd 53, RD DTO !!
> sunxi-mmc 1c12000.mmc: data error, sending stop command
> sunxi-mmc 1c12000.mmc: smc 1 err, cmd 53, RD DTO !!
> sunxi-mmc 1c12000.mmc: data error, sending stop command
>
> The chip is pretty much dead afterwards.
>
> With cap-sdio-irq it doesn't happen so soon, but it does.
> Without either, the response time is bad with packet losses,
> but at least it doesn't die.

That is not true, without either cap-sdio-irq or oob irq it
still dies, try doing a scp of a large file, that is a more
reliable way to trigger it.

I've been down this road (blaming the irq) mechanism myself,
but it is a dead end, the problem you're describing, the CMD 53
SBE error happens with all 3 irq mechanisms.

> Is this the problem Arend (CC-ed) was looking into?

Is looking into, yes. He has a Cubietruck now, and he can reproduce
it, so hopefully we will see some progress on this soon.

Note that as a workaround (for me at least) you can boot into
the linux on the cubietruck nand, then insert an sdcard with
upstream kernel, then reboot so that it boots from the sdcard
without loosing power, and then the problem seems to be gone.

Regards,

Hans

[linux-sunxi] [PATCH 7/7] ARM: dts: sun7i: Enable cap-sdio-irq for bananapro sdio wifi

[Hans de Goede]

Hi,

On 08-03-15 03:42, Chen-Yu Tsai wrote:
> On Sun, Mar 8, 2015 at 3:01 AM, Hans de Goede <hdegoede@redhat.com> wrote:
>> The sdio wifi on the Banana Pro does not appear to have an oob irq hooked
>> up, so enable sdio-irq support to avoid unnecessary polling.
>
> I wonder if this is stable enough to put back into the mmc driver, i.e.
> declare the capability in the driver itself? IIRC at one point it did.

That is a good question, I believe strongly that the sdio wifi issues we've
been seeing which were the reason to disable cap-sdio-irq in the driver are
actually unrelated to the irq delivery mechanism. So IMHO yes we can just enable
this for all devices in the driver, and yes that would be a better solution.

Maxime, if I send a patch to enable cal-sdio-irq at the driver level ( as it
really is a hardware feature not a board feature), will you ack it ?

If the answer is yet, then please do NOT apply this patch and I'll send
a sunxi-mmc.c patch instead.

Regards,

Hans



>
> ChenYu
>
>> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
>> ---
>>   arch/arm/boot/dts/sun7i-a20-bananapro.dts | 1 +
>>   1 file changed, 1 insertion(+)
>>
>> diff --git a/arch/arm/boot/dts/sun7i-a20-bananapro.dts b/arch/arm/boot/dts/sun7i-a20-bananapro.dts
>> index fb89fe7..d0cd78f 100644
>> --- a/arch/arm/boot/dts/sun7i-a20-bananapro.dts
>> +++ b/arch/arm/boot/dts/sun7i-a20-bananapro.dts
>> @@ -164,6 +164,7 @@
>>          vmmc-supply = <&reg_vmmc3>;
>>          bus-width = <4>;
>>          non-removable;
>> +       cap-sdio-irq;
>>          status = "okay";
>>   };
>>
>> --
>> 2.3.1
>

[PATCH 1/7] ARM: dts: sun4i: Enable tablet keys on Chuwi V7 CW0825

[Maxime Ripard]

On Sat, Mar 07, 2015 at 08:01:18PM +0100, Hans de Goede wrote:
> Enable the lradc controlled tablet keys on the Chuwi V7 CW0825 tablet.
> 
> Signed-off-by: Hans de Goede <hdegoede@redhat.com>

Applied, thanks!

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150308/7415fc03/attachment.sig>

[PATCH 2/7] ARM: dts: sun5i: Stop using different compatibles for ehci/ohci on a13 vs a10s

[Maxime Ripard]

On Sat, Mar 07, 2015 at 08:01:19PM +0100, Hans de Goede wrote:
> The A13 and the A10s use the same die (this has been confirmed by Allwinner),
> as such there is no need to differentiate between the ehci/ohci parts of both,
> the only reasons there were different allwinner,sun5i-a*-foo compatible
> between these 2 parts is costemetically and because we could when we still
> had 2 completely different dtsi files.
> 
> The allwinner,sun5i-a*-foo compatible strings are not used for binding at all,
> the actual driver binds to the generic-?hci compatible, so we can safely remove
> this cosmetical difference and simplify the dtsi files.
> 
> Signed-off-by: Hans de Goede <hdegoede@redhat.com>

Appplied, thanks!

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150308/e2ce700d/attachment.sig>

[PATCH 3/7] ARM: dts: sun5i: Add mmc2 pinmux settings

[Maxime Ripard]

On Sat, Mar 07, 2015 at 08:01:20PM +0100, Hans de Goede wrote:
> Add A13 mmc2 pinmux settings, note these are for a 8bit bus.
> 
> Signed-off-by: Hans de Goede <hdegoede@redhat.com>

Applied, thanks!

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150308/e7aaf194/attachment.sig>

[PATCH 4/7] ARM: dts: sun5i: Add new Auxtek-t004 board

[Maxime Ripard]

On Sat, Mar 07, 2015 at 08:01:21PM +0100, Hans de Goede wrote:
> The auxtek-t004:
> http://www.fasttech.com/products/1110/10004200/1318603-auxtek-t004-allwinner-a10s-single-core-android-ics
> 
> Is an Allwinner A10s based hdmi tv stick with with 512M RAM, 4G nand flash,
> toc9002 (bcm43362) sdio wifi, 1 USB host ports using an USB-A receptacle and
> a 2 micro-usb receptacles, one for power and one for USB OTG.
> 
> The sdio wifi appears to not have an oob irq hooked up, so we rely on sdio-irq
> support for it.
> 
> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
> 
> foo

I'm not sure what that foo was about :)

I removed it, and applied the patch, thanks!

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150308/8a2bc2d5/attachment.sig>

[PATCH 5/7] ARM: dts: sun5i: Add new Utoo P66 board

[Maxime Ripard]

On Sat, Mar 07, 2015 at 08:01:22PM +0100, Hans de Goede wrote:
> The UTOO P66 is a 6" A13 tablet / lcd ereader. It features a 6" 480x800 ips
> lcd screen, 512MB RAM & 4GB emmc.
> 
> Signed-off-by: Hans de Goede <hdegoede@redhat.com>

Applied, thanks!

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150308/c82a25b1/attachment.sig>

[PATCH 6/7] ARM: dts: sun7i: Add OOB irq support to boards with broadcom sdio wifi

[Maxime Ripard]

On Sat, Mar 07, 2015 at 08:01:23PM +0100, Hans de Goede wrote:
> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
> ---
>  arch/arm/boot/dts/sun7i-a20-cubietruck.dts | 11 +++++++++++
>  arch/arm/boot/dts/sun7i-a20-i12-tvbox.dts  | 11 +++++++++++
>  2 files changed, 22 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts
> index 0c219a4..8111b0c 100644
> --- a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts
> +++ b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts
> @@ -167,12 +167,23 @@
>  };
>  
>  &mmc3 {
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +

Aside from Chen-Yu's comments, that should be in the DTSI.

>  	pinctrl-names = "default";
>  	pinctrl-0 = <&mmc3_pins_a>;
>  	vmmc-supply = <&reg_vmmc3>;
>  	bus-width = <4>;
>  	non-removable;
>  	status = "okay";
> +
> +	brcmf: bcrmf at 1 {
> +		reg = <1>;
> +		compatible = "brcm,bcm4329-fmac";
> +		interrupt-parent = <&pio>;
> +		interrupts = <10 8>; /* PH10 / EINT10 */

And you can use interrupts-extented here (not that I really care much,
both solutions works for me).

Thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150308/2fc0ca41/attachment-0001.sig>

[linux-sunxi] [PATCH 7/7] ARM: dts: sun7i: Enable cap-sdio-irq for bananapro sdio wifi

[Maxime Ripard]

On Sun, Mar 08, 2015 at 12:27:53PM +0100, Hans de Goede wrote:
> Hi,
> 
> On 08-03-15 03:42, Chen-Yu Tsai wrote:
> >On Sun, Mar 8, 2015 at 3:01 AM, Hans de Goede <hdegoede@redhat.com> wrote:
> >>The sdio wifi on the Banana Pro does not appear to have an oob irq hooked
> >>up, so enable sdio-irq support to avoid unnecessary polling.
> >
> >I wonder if this is stable enough to put back into the mmc driver, i.e.
> >declare the capability in the driver itself? IIRC at one point it did.
> 
> That is a good question, I believe strongly that the sdio wifi issues we've
> been seeing which were the reason to disable cap-sdio-irq in the driver are
> actually unrelated to the irq delivery mechanism. So IMHO yes we can just enable
> this for all devices in the driver, and yes that would be a better solution.
> 
> Maxime, if I send a patch to enable cal-sdio-irq at the driver level ( as it
> really is a hardware feature not a board feature), will you ack it ?

You know a lot more than I do on this, so I fully trust you. If you
feel like it's the best solution, go ahead.

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150308/a70e052d/attachment-0001.sig>

[PATCH 4/7] ARM: dts: sun5i: Add new Auxtek-t004 board

[Hans de Goede]

Hi,

On 08-03-15 18:21, Maxime Ripard wrote:
> On Sat, Mar 07, 2015 at 08:01:21PM +0100, Hans de Goede wrote:
>> The auxtek-t004:
>> http://www.fasttech.com/products/1110/10004200/1318603-auxtek-t004-allwinner-a10s-single-core-android-ics
>>
>> Is an Allwinner A10s based hdmi tv stick with with 512M RAM, 4G nand flash,
>> toc9002 (bcm43362) sdio wifi, 1 USB host ports using an USB-A receptacle and
>> a 2 micro-usb receptacles, one for power and one for USB OTG.
>>
>> The sdio wifi appears to not have an oob irq hooked up, so we rely on sdio-irq
>> support for it.
>>
>> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
>>
>> foo
>
> I'm not sure what that foo was about :)

Heh, that was the commit message of a fixup commit which I apparently
added with a s (squash) rather then a f (fix) when doing a rebase -i leaving
the foo in the combined commit msg. So now if you ever see a "foo" in a commit
msg from me again you know where it comes from :)

Regards,

Hans

[PATCH 6/7] ARM: dts: sun7i: Add OOB irq support to boards with broadcom sdio wifi

[Hans de Goede]

Hi,

On 08-03-15 18:25, Maxime Ripard wrote:
> On Sat, Mar 07, 2015 at 08:01:23PM +0100, Hans de Goede wrote:
>> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
>> ---
>>   arch/arm/boot/dts/sun7i-a20-cubietruck.dts | 11 +++++++++++
>>   arch/arm/boot/dts/sun7i-a20-i12-tvbox.dts  | 11 +++++++++++
>>   2 files changed, 22 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts
>> index 0c219a4..8111b0c 100644
>> --- a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts
>> +++ b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts
>> @@ -167,12 +167,23 @@
>>   };
>>
>>   &mmc3 {
>> +	#address-cells = <1>;
>> +	#size-cells = <0>;
>> +
>
> Aside from Chen-Yu's comments, that should be in the DTSI.
>
>>   	pinctrl-names = "default";
>>   	pinctrl-0 = <&mmc3_pins_a>;
>>   	vmmc-supply = <&reg_vmmc3>;
>>   	bus-width = <4>;
>>   	non-removable;
>>   	status = "okay";
>> +
>> +	brcmf: bcrmf at 1 {
>> +		reg = <1>;
>> +		compatible = "brcm,bcm4329-fmac";
>> +		interrupt-parent = <&pio>;
>> +		interrupts = <10 8>; /* PH10 / EINT10 */
>
> And you can use interrupts-extented here (not that I really care much,
> both solutions works for me).

What is interrupts-extended / does interrupts-extended do ?

Ah, found it, Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
says:

The "interrupts-extended" property is a special form for use when a node needs
to reference multiple interrupt parents. Each entry in this property contains
both the parent phandle and the interrupt specifier. "interrupts-extended"
should only be used when a device has multiple interrupt parents.

   Example:
         interrupts-extended = <&intc1 5 1>, <&intc2 1 0>;

So since we do not need multiple interrupt parents here, "interrupts = "
seems to be the better syntax to use, I'll do a new version fixing
ChenYu's comments and moving the #foo-cells to the dtsi.

Thanks for merging the other patches, and for the review.

Regards,

Hans

[PATCH 4/7] ARM: dts: sun5i: Add new Auxtek-t004 board

[Maxime Ripard]

On Sun, Mar 08, 2015 at 08:15:30PM +0100, Hans de Goede wrote:
> Hi,
> 
> On 08-03-15 18:21, Maxime Ripard wrote:
> >On Sat, Mar 07, 2015 at 08:01:21PM +0100, Hans de Goede wrote:
> >>The auxtek-t004:
> >>http://www.fasttech.com/products/1110/10004200/1318603-auxtek-t004-allwinner-a10s-single-core-android-ics
> >>
> >>Is an Allwinner A10s based hdmi tv stick with with 512M RAM, 4G nand flash,
> >>toc9002 (bcm43362) sdio wifi, 1 USB host ports using an USB-A receptacle and
> >>a 2 micro-usb receptacles, one for power and one for USB OTG.
> >>
> >>The sdio wifi appears to not have an oob irq hooked up, so we rely on sdio-irq
> >>support for it.
> >>
> >>Signed-off-by: Hans de Goede <hdegoede@redhat.com>
> >>
> >>foo
> >
> >I'm not sure what that foo was about :)
> 
> Heh, that was the commit message of a fixup commit which I apparently
> added with a s (squash) rather then a f (fix) when doing a rebase -i leaving
> the foo in the combined commit msg. So now if you ever see a "foo" in a commit
> msg from me again you know where it comes from :)

Noted :)

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150309/e731aa6d/attachment.sig>