* [PATCH V4 2/4] arm64: dts: freescale: Add i.MX8MN dtsi support
2019-06-19 2:21 [PATCH V4 1/4] dt-bindings: arm: imx: Add the soc binding for i.MX8MN Anson.Huang
@ 2019-06-19 2:21 ` Anson.Huang
2019-06-19 2:21 ` [PATCH V4 3/4] arm64: dts: freescale: Add i.MX8MN DDR4 EVK board support Anson.Huang
` (3 subsequent siblings)
4 siblings, 0 replies; 7+ messages in thread
From: Anson.Huang @ 2019-06-19 2:21 UTC (permalink / raw)
To: robh+dt, mark.rutland, shawnguo, s.hauer, kernel, festevam,
andrew.smirnov, manivannan.sadhasivam, j.neuschaefer,
u.kleine-koenig, leoyang.li, aisheng.dong, l.stach,
vabhav.sharma, bhaskar.upadhaya, ping.bai, pramod.kumar_1,
leonard.crestez, daniel.baluta, devicetree, linux-kernel,
linux-arm-kernel
Cc: Linux-imx
From: Anson Huang <Anson.Huang@nxp.com>
The i.MX8M Nano Media Applications Processor is a new SoC of the i.MX8M
family, it is a 14nm FinFET product of the growing mScale family targeting
the consumer market. It is built in Samsung 14LPP to achieve both high
performance and low power consumption and relies on a powerful fully
coherent core complex based on a quad core ARM Cortex-A53 cluster,
Cortex-M7 low-power coprocessor and graphics accelerator.
This patch adds the basic dtsi support for i.MX8MN.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
---
Changes since V3:
- add "fsl,imx8mm-anatop" as anatop's fallback compatible to support SoC driver.
---
arch/arm64/boot/dts/freescale/imx8mn.dtsi | 712 ++++++++++++++++++++++++++++++
1 file changed, 712 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/imx8mn.dtsi
diff --git a/arch/arm64/boot/dts/freescale/imx8mn.dtsi b/arch/arm64/boot/dts/freescale/imx8mn.dtsi
new file mode 100644
index 0000000..f5eff35
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mn.dtsi
@@ -0,0 +1,712 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019 NXP
+ */
+
+#include <dt-bindings/clock/imx8mn-clock.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+#include "imx8mn-pinfunc.h"
+
+/ {
+ compatible = "fsl,imx8mn";
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ aliases {
+ ethernet0 = &fec1;
+ gpio0 = &gpio1;
+ gpio1 = &gpio2;
+ gpio2 = &gpio3;
+ gpio3 = &gpio4;
+ gpio4 = &gpio5;
+ i2c0 = &i2c1;
+ i2c1 = &i2c2;
+ i2c2 = &i2c3;
+ i2c3 = &i2c4;
+ mmc0 = &usdhc1;
+ mmc1 = &usdhc2;
+ mmc2 = &usdhc3;
+ serial0 = &uart1;
+ serial1 = &uart2;
+ serial2 = &uart3;
+ serial3 = &uart4;
+ spi0 = &ecspi1;
+ spi1 = &ecspi2;
+ spi2 = &ecspi3;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ A53_0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x0>;
+ clock-latency = <61036>;
+ clocks = <&clk IMX8MN_CLK_ARM>;
+ enable-method = "psci";
+ next-level-cache = <&A53_L2>;
+ };
+
+ A53_1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x1>;
+ clock-latency = <61036>;
+ clocks = <&clk IMX8MN_CLK_ARM>;
+ enable-method = "psci";
+ next-level-cache = <&A53_L2>;
+ };
+
+ A53_2: cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x2>;
+ clock-latency = <61036>;
+ clocks = <&clk IMX8MN_CLK_ARM>;
+ enable-method = "psci";
+ next-level-cache = <&A53_L2>;
+ };
+
+ A53_3: cpu@3 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x3>;
+ clock-latency = <61036>;
+ clocks = <&clk IMX8MN_CLK_ARM>;
+ enable-method = "psci";
+ next-level-cache = <&A53_L2>;
+ };
+
+ A53_L2: l2-cache0 {
+ compatible = "cache";
+ };
+ };
+
+ memory@40000000 {
+ device_type = "memory";
+ reg = <0x0 0x40000000 0 0x80000000>;
+ };
+
+ osc_32k: clock-osc-32k {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ clock-output-names = "osc_32k";
+ };
+
+ osc_24m: clock-osc-24m {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24000000>;
+ clock-output-names = "osc_24m";
+ };
+
+ clk_ext1: clock-ext1 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <133000000>;
+ clock-output-names = "clk_ext1";
+ };
+
+ clk_ext2: clock-ext2 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <133000000>;
+ clock-output-names = "clk_ext2";
+ };
+
+ clk_ext3: clock-ext3 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <133000000>;
+ clock-output-names = "clk_ext3";
+ };
+
+ clk_ext4: clock-ext4 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency= <133000000>;
+ clock-output-names = "clk_ext4";
+ };
+
+ psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>;
+ clock-frequency = <8000000>;
+ arm,no-tick-in-suspend;
+ };
+
+ soc@0 {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x0 0x0 0x3e000000>;
+
+ aips1: bus@30000000 {
+ compatible = "fsl,aips-bus", "simple-bus";
+ reg = <0x30000000 0x400000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ gpio1: gpio@30200000 {
+ compatible = "fsl,imx8mn-gpio", "fsl,imx35-gpio";
+ reg = <0x30200000 0x10000>;
+ interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MN_CLK_GPIO1_ROOT>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio2: gpio@30210000 {
+ compatible = "fsl,imx8mn-gpio", "fsl,imx35-gpio";
+ reg = <0x30210000 0x10000>;
+ interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MN_CLK_GPIO2_ROOT>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio3: gpio@30220000 {
+ compatible = "fsl,imx8mn-gpio", "fsl,imx35-gpio";
+ reg = <0x30220000 0x10000>;
+ interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MN_CLK_GPIO3_ROOT>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio4: gpio@30230000 {
+ compatible = "fsl,imx8mn-gpio", "fsl,imx35-gpio";
+ reg = <0x30230000 0x10000>;
+ interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MN_CLK_GPIO4_ROOT>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio5: gpio@30240000 {
+ compatible = "fsl,imx8mn-gpio", "fsl,imx35-gpio";
+ reg = <0x30240000 0x10000>;
+ interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MN_CLK_GPIO5_ROOT>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ wdog1: watchdog@30280000 {
+ compatible = "fsl,imx8mn-wdt", "fsl,imx21-wdt";
+ reg = <0x30280000 0x10000>;
+ interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MN_CLK_WDOG1_ROOT>;
+ status = "disabled";
+ };
+
+ wdog2: watchdog@30290000 {
+ compatible = "fsl,imx8mn-wdt", "fsl,imx21-wdt";
+ reg = <0x30290000 0x10000>;
+ interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MN_CLK_WDOG2_ROOT>;
+ status = "disabled";
+ };
+
+ wdog3: watchdog@302a0000 {
+ compatible = "fsl,imx8mn-wdt", "fsl,imx21-wdt";
+ reg = <0x302a0000 0x10000>;
+ interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MN_CLK_WDOG3_ROOT>;
+ status = "disabled";
+ };
+
+ sdma3: dma-controller@302b0000 {
+ compatible = "fsl,imx8mn-sdma", "fsl,imx7d-sdma";
+ reg = <0x302b0000 0x10000>;
+ interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MN_CLK_SDMA3_ROOT>,
+ <&clk IMX8MN_CLK_SDMA3_ROOT>;
+ clock-names = "ipg", "ahb";
+ #dma-cells = <3>;
+ fsl,sdma-ram-script-name = "imx/sdma/sdma-imx7d.bin";
+ };
+
+ sdma2: dma-controller@302c0000 {
+ compatible = "fsl,imx8mn-sdma", "fsl,imx7d-sdma";
+ reg = <0x302c0000 0x10000>;
+ interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MN_CLK_SDMA2_ROOT>,
+ <&clk IMX8MN_CLK_SDMA2_ROOT>;
+ clock-names = "ipg", "ahb";
+ #dma-cells = <3>;
+ fsl,sdma-ram-script-name = "imx/sdma/sdma-imx7d.bin";
+ };
+
+ iomuxc: pinctrl@30330000 {
+ compatible = "fsl,imx8mn-iomuxc";
+ reg = <0x30330000 0x10000>;
+ };
+
+ gpr: iomuxc-gpr@30340000 {
+ compatible = "fsl,imx8mn-iomuxc-gpr", "syscon";
+ reg = <0x30340000 0x10000>;
+ };
+
+ ocotp: ocotp-ctrl@30350000 {
+ compatible = "fsl,imx8mn-ocotp", "fsl,imx7d-ocotp", "syscon";
+ reg = <0x30350000 0x10000>;
+ clocks = <&clk IMX8MN_CLK_OCOTP_ROOT>;
+ };
+
+ anatop: anatop@30360000 {
+ compatible = "fsl,imx8mn-anatop", "fsl,imx8mm-anatop",
+ "syscon", "simple-bus";
+ reg = <0x30360000 0x10000>;
+ };
+
+ snvs: snvs@30370000 {
+ compatible = "fsl,sec-v4.0-mon","syscon", "simple-mfd";
+ reg = <0x30370000 0x10000>;
+
+ snvs_rtc: snvs-rtc-lp {
+ compatible = "fsl,sec-v4.0-mon-rtc-lp";
+ regmap = <&snvs>;
+ offset = <0x34>;
+ interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "snvs-rtc";
+ };
+
+ snvs_pwrkey: snvs-powerkey {
+ compatible = "fsl,sec-v4.0-pwrkey";
+ regmap = <&snvs>;
+ interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+ linux,keycode = <KEY_POWER>;
+ wakeup-source;
+ status = "disabled";
+ };
+ };
+
+ clk: clock-controller@30380000 {
+ compatible = "fsl,imx8mn-ccm";
+ reg = <0x30380000 0x10000>;
+ #clock-cells = <1>;
+ clocks = <&osc_32k>, <&osc_24m>, <&clk_ext1>, <&clk_ext2>,
+ <&clk_ext3>, <&clk_ext4>;
+ clock-names = "osc_32k", "osc_24m", "clk_ext1", "clk_ext2",
+ "clk_ext3", "clk_ext4";
+ };
+
+ src: reset-controller@30390000 {
+ compatible = "fsl,imx8mn-src", "syscon";
+ reg = <0x30390000 0x10000>;
+ interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+ #reset-cells = <1>;
+ };
+ };
+
+ aips2: bus@30400000 {
+ compatible = "fsl,aips-bus", "simple-bus";
+ reg = <0x30400000 0x400000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ pwm1: pwm@30660000 {
+ compatible = "fsl,imx8mn-pwm", "fsl,imx27-pwm";
+ reg = <0x30660000 0x10000>;
+ interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MN_CLK_PWM1_ROOT>,
+ <&clk IMX8MN_CLK_PWM1_ROOT>;
+ clock-names = "ipg", "per";
+ #pwm-cells = <2>;
+ status = "disabled";
+ };
+
+ pwm2: pwm@30670000 {
+ compatible = "fsl,imx8mn-pwm", "fsl,imx27-pwm";
+ reg = <0x30670000 0x10000>;
+ interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MN_CLK_PWM2_ROOT>,
+ <&clk IMX8MN_CLK_PWM2_ROOT>;
+ clock-names = "ipg", "per";
+ #pwm-cells = <2>;
+ status = "disabled";
+ };
+
+ pwm3: pwm@30680000 {
+ compatible = "fsl,imx8mn-pwm", "fsl,imx27-pwm";
+ reg = <0x30680000 0x10000>;
+ interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MN_CLK_PWM3_ROOT>,
+ <&clk IMX8MN_CLK_PWM3_ROOT>;
+ clock-names = "ipg", "per";
+ #pwm-cells = <2>;
+ status = "disabled";
+ };
+
+ pwm4: pwm@30690000 {
+ compatible = "fsl,imx8mn-pwm", "fsl,imx27-pwm";
+ reg = <0x30690000 0x10000>;
+ interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MN_CLK_PWM4_ROOT>,
+ <&clk IMX8MN_CLK_PWM4_ROOT>;
+ clock-names = "ipg", "per";
+ #pwm-cells = <2>;
+ status = "disabled";
+ };
+ };
+
+ aips3: bus@30800000 {
+ compatible = "fsl,aips-bus", "simple-bus";
+ reg = <0x30800000 0x400000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ ecspi1: spi@30820000 {
+ compatible = "fsl,imx8mn-ecspi", "fsl,imx51-ecspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x30820000 0x10000>;
+ interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MN_CLK_ECSPI1_ROOT>,
+ <&clk IMX8MN_CLK_ECSPI1_ROOT>;
+ clock-names = "ipg", "per";
+ dmas = <&sdma1 0 7 1>, <&sdma1 1 7 2>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ ecspi2: spi@30830000 {
+ compatible = "fsl,imx8mn-ecspi", "fsl,imx51-ecspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x30830000 0x10000>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MN_CLK_ECSPI2_ROOT>,
+ <&clk IMX8MN_CLK_ECSPI2_ROOT>;
+ clock-names = "ipg", "per";
+ dmas = <&sdma1 2 7 1>, <&sdma1 3 7 2>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ ecspi3: spi@30840000 {
+ compatible = "fsl,imx8mn-ecspi", "fsl,imx51-ecspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x30840000 0x10000>;
+ interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MN_CLK_ECSPI3_ROOT>,
+ <&clk IMX8MN_CLK_ECSPI3_ROOT>;
+ clock-names = "ipg", "per";
+ dmas = <&sdma1 4 7 1>, <&sdma1 5 7 2>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart1: serial@30860000 {
+ compatible = "fsl,imx8mn-uart", "fsl,imx6q-uart";
+ reg = <0x30860000 0x10000>;
+ interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MN_CLK_UART1_ROOT>,
+ <&clk IMX8MN_CLK_UART1_ROOT>;
+ clock-names = "ipg", "per";
+ dmas = <&sdma1 22 4 0>, <&sdma1 23 4 0>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart3: serial@30880000 {
+ compatible = "fsl,imx8mn-uart", "fsl,imx6q-uart";
+ reg = <0x30880000 0x10000>;
+ interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MN_CLK_UART3_ROOT>,
+ <&clk IMX8MN_CLK_UART3_ROOT>;
+ clock-names = "ipg", "per";
+ dmas = <&sdma1 26 4 0>, <&sdma1 27 4 0>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart2: serial@30890000 {
+ compatible = "fsl,imx8mn-uart", "fsl,imx6q-uart";
+ reg = <0x30890000 0x10000>;
+ interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MN_CLK_UART2_ROOT>,
+ <&clk IMX8MN_CLK_UART2_ROOT>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ i2c1: i2c@30a20000 {
+ compatible = "fsl,imx8mn-i2c", "fsl,imx21-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x30a20000 0x10000>;
+ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MN_CLK_I2C1_ROOT>;
+ status = "disabled";
+ };
+
+ i2c2: i2c@30a30000 {
+ compatible = "fsl,imx8mn-i2c", "fsl,imx21-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x30a30000 0x10000>;
+ interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MN_CLK_I2C2_ROOT>;
+ status = "disabled";
+ };
+
+ i2c3: i2c@30a40000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx8mn-i2c", "fsl,imx21-i2c";
+ reg = <0x30a40000 0x10000>;
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MN_CLK_I2C3_ROOT>;
+ status = "disabled";
+ };
+
+ i2c4: i2c@30a50000 {
+ compatible = "fsl,imx8mn-i2c", "fsl,imx21-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x30a50000 0x10000>;
+ interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MN_CLK_I2C4_ROOT>;
+ status = "disabled";
+ };
+
+ uart4: serial@30a60000 {
+ compatible = "fsl,imx8mn-uart", "fsl,imx6q-uart";
+ reg = <0x30a60000 0x10000>;
+ interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MN_CLK_UART4_ROOT>,
+ <&clk IMX8MN_CLK_UART4_ROOT>;
+ clock-names = "ipg", "per";
+ dmas = <&sdma1 28 4 0>, <&sdma1 29 4 0>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ usdhc1: mmc@30b40000 {
+ compatible = "fsl,imx8mn-usdhc", "fsl,imx7d-usdhc";
+ reg = <0x30b40000 0x10000>;
+ interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MN_CLK_DUMMY>,
+ <&clk IMX8MN_CLK_NAND_USDHC_BUS>,
+ <&clk IMX8MN_CLK_USDHC1_ROOT>;
+ clock-names = "ipg", "ahb", "per";
+ assigned-clocks = <&clk IMX8MN_CLK_USDHC1>;
+ assigned-clock-rates = <400000000>;
+ fsl,tuning-start-tap = <20>;
+ fsl,tuning-step= <2>;
+ bus-width = <4>;
+ status = "disabled";
+ };
+
+ usdhc2: mmc@30b50000 {
+ compatible = "fsl,imx8mn-usdhc", "fsl,imx7d-usdhc";
+ reg = <0x30b50000 0x10000>;
+ interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MN_CLK_DUMMY>,
+ <&clk IMX8MN_CLK_NAND_USDHC_BUS>,
+ <&clk IMX8MN_CLK_USDHC2_ROOT>;
+ clock-names = "ipg", "ahb", "per";
+ fsl,tuning-start-tap = <20>;
+ fsl,tuning-step= <2>;
+ bus-width = <4>;
+ status = "disabled";
+ };
+
+ usdhc3: mmc@30b60000 {
+ compatible = "fsl,imx8mn-usdhc", "fsl,imx7d-usdhc";
+ reg = <0x30b60000 0x10000>;
+ interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MN_CLK_DUMMY>,
+ <&clk IMX8MN_CLK_NAND_USDHC_BUS>,
+ <&clk IMX8MN_CLK_USDHC3_ROOT>;
+ clock-names = "ipg", "ahb", "per";
+ assigned-clocks = <&clk IMX8MN_CLK_USDHC3_ROOT>;
+ assigned-clock-rates = <400000000>;
+ fsl,tuning-start-tap = <20>;
+ fsl,tuning-step= <2>;
+ bus-width = <4>;
+ status = "disabled";
+ };
+
+ sdma1: dma-controller@30bd0000 {
+ compatible = "fsl,imx8mn-sdma", "fsl,imx7d-sdma";
+ reg = <0x30bd0000 0x10000>;
+ interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MN_CLK_SDMA1_ROOT>,
+ <&clk IMX8MN_CLK_SDMA1_ROOT>;
+ clock-names = "ipg", "ahb";
+ #dma-cells = <3>;
+ fsl,sdma-ram-script-name = "imx/sdma/sdma-imx7d.bin";
+ };
+
+ fec1: ethernet@30be0000 {
+ compatible = "fsl,imx8mn-fec", "fsl,imx6sx-fec";
+ reg = <0x30be0000 0x10000>;
+ interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MN_CLK_ENET1_ROOT>,
+ <&clk IMX8MN_CLK_ENET1_ROOT>,
+ <&clk IMX8MN_CLK_ENET_TIMER>,
+ <&clk IMX8MN_CLK_ENET_REF>,
+ <&clk IMX8MN_CLK_ENET_PHY_REF>;
+ clock-names = "ipg", "ahb", "ptp",
+ "enet_clk_ref", "enet_out";
+ assigned-clocks = <&clk IMX8MN_CLK_ENET_AXI>,
+ <&clk IMX8MN_CLK_ENET_TIMER>,
+ <&clk IMX8MN_CLK_ENET_REF>,
+ <&clk IMX8MN_CLK_ENET_TIMER>;
+ assigned-clock-parents = <&clk IMX8MN_SYS_PLL1_266M>,
+ <&clk IMX8MN_SYS_PLL2_100M>,
+ <&clk IMX8MN_SYS_PLL2_125M>;
+ assigned-clock-rates = <0>, <0>, <125000000>, <100000000>;
+ fsl,num-tx-queues = <3>;
+ fsl,num-rx-queues = <3>;
+ status = "disabled";
+ };
+
+ };
+
+ aips4: bus@32c00000 {
+ compatible = "fsl,aips-bus", "simple-bus";
+ reg = <0x32c00000 0x400000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ usbotg1: usb@32e40000 {
+ compatible = "fsl,imx8mn-usb", "fsl,imx7d-usb";
+ reg = <0x32e40000 0x200>;
+ interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MN_CLK_USB1_CTRL_ROOT>;
+ clock-names = "usb1_ctrl_root_clk";
+ assigned-clocks = <&clk IMX8MN_CLK_USB_BUS>,
+ <&clk IMX8MN_CLK_USB_CORE_REF>;
+ assigned-clock-parents = <&clk IMX8MN_SYS_PLL2_500M>,
+ <&clk IMX8MN_SYS_PLL1_100M>;
+ fsl,usbphy = <&usbphynop1>;
+ fsl,usbmisc = <&usbmisc1 0>;
+ status = "disabled";
+ };
+
+ usbmisc1: usbmisc@32e40200 {
+ compatible = "fsl,imx8mn-usbmisc", "fsl,imx7d-usbmisc";
+ #index-cells = <1>;
+ reg = <0x32e40200 0x200>;
+ };
+
+ usbotg2: usb@32e50000 {
+ compatible = "fsl,imx8mn-usb", "fsl,imx7d-usb";
+ reg = <0x32e50000 0x200>;
+ interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MN_CLK_USB1_CTRL_ROOT>;
+ clock-names = "usb1_ctrl_root_clk";
+ assigned-clocks = <&clk IMX8MN_CLK_USB_BUS>,
+ <&clk IMX8MN_CLK_USB_CORE_REF>;
+ assigned-clock-parents = <&clk IMX8MN_SYS_PLL2_500M>,
+ <&clk IMX8MN_SYS_PLL1_100M>;
+ fsl,usbphy = <&usbphynop2>;
+ fsl,usbmisc = <&usbmisc2 0>;
+ status = "disabled";
+ };
+
+ usbmisc2: usbmisc@32e50200 {
+ compatible = "fsl,imx8mn-usbmisc", "fsl,imx7d-usbmisc";
+ #index-cells = <1>;
+ reg = <0x32e50200 0x200>;
+ };
+
+ };
+
+ dma_apbh: dma-controller@33000000 {
+ compatible = "fsl,imx7d-dma-apbh", "fsl,imx28-dma-apbh";
+ reg = <0x33000000 0x2000>;
+ interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "gpmi0", "gpmi1", "gpmi2", "gpmi3";
+ #dma-cells = <1>;
+ dma-channels = <4>;
+ clocks = <&clk IMX8MN_CLK_NAND_USDHC_BUS_RAWNAND_CLK>;
+ };
+
+ gpmi: nand-controller@33002000 {
+ compatible = "fsl,imx8mn-gpmi-nand", "fsl,imx7d-gpmi-nand";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x33002000 0x2000>, <0x33004000 0x4000>;
+ reg-names = "gpmi-nand", "bch";
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "bch";
+ clocks = <&clk IMX8MN_CLK_NAND_ROOT>,
+ <&clk IMX8MN_CLK_NAND_USDHC_BUS_RAWNAND_CLK>;
+ clock-names = "gpmi_io", "gpmi_bch_apb";
+ dmas = <&dma_apbh 0>;
+ dma-names = "rx-tx";
+ status = "disabled";
+ };
+
+ gic: interrupt-controller@38800000 {
+ compatible = "arm,gic-v3";
+ reg = <0x38800000 0x10000>,
+ <0x38880000 0xc0000>;
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+
+ usbphynop1: usbphynop1 {
+ compatible = "usb-nop-xceiv";
+ clocks = <&clk IMX8MN_CLK_USB_PHY_REF>;
+ assigned-clocks = <&clk IMX8MN_CLK_USB_PHY_REF>;
+ assigned-clock-parents = <&clk IMX8MN_SYS_PLL1_100M>;
+ clock-names = "main_clk";
+ };
+
+ usbphynop2: usbphynop2 {
+ compatible = "usb-nop-xceiv";
+ clocks = <&clk IMX8MN_CLK_USB_PHY_REF>;
+ assigned-clocks = <&clk IMX8MN_CLK_USB_PHY_REF>;
+ assigned-clock-parents = <&clk IMX8MN_SYS_PLL1_100M>;
+ clock-names = "main_clk";
+ };
+};
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 7+ messages in thread