* [PATCH v4] arm64: dts: imx8mq: Init rates and parents configs for clocks
@ 2019-07-28 15:20 Daniel Baluta
2019-07-29 12:48 ` Guido Günther
` (2 more replies)
0 siblings, 3 replies; 6+ messages in thread
From: Daniel Baluta @ 2019-07-28 15:20 UTC (permalink / raw)
To: shawnguo
Cc: devicetree, baruch, abel.vesa, Anson.Huang, ccaione,
andrew.smirnov, Daniel Baluta, s.hauer, angus, linux-kernel, agx,
linux-imx, festevam, shengjiu.wang, linux-arm-kernel, l.stach
From: Abel Vesa <abel.vesa@nxp.com>
Add the initial configuration for clocks that need default parent and rate
setting. This is based on the vendor tree clock provider parents and rates
configuration except this is doing the setup in dts rather then using clock
consumer API in a clock provider driver.
Note that by adding the initial rate setting for audio_pll1/audio_pll
setting we need to remove it from imx8mq-librem5-devkit.dts
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Tested-by: Angus Ainslie (Purism) <angus@akkea.ca>
---
Changes since v3:
- fix extra new lines
.../dts/freescale/imx8mq-librem5-devkit.dts | 5 -----
arch/arm64/boot/dts/freescale/imx8mq.dtsi | 19 +++++++++++++++++++
2 files changed, 19 insertions(+), 5 deletions(-)
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
index 683a11035643..c702ccc82867 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
@@ -169,11 +169,6 @@
};
};
-&clk {
- assigned-clocks = <&clk IMX8MQ_AUDIO_PLL1>, <&clk IMX8MQ_AUDIO_PLL2>;
- assigned-clock-rates = <786432000>, <722534400>;
-};
-
&dphy {
status = "okay";
};
diff --git a/arch/arm64/boot/dts/freescale/imx8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
index 02fbd0625318..a55d72ba2e05 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
@@ -494,6 +494,25 @@
clock-names = "ckil", "osc_25m", "osc_27m",
"clk_ext1", "clk_ext2",
"clk_ext3", "clk_ext4";
+ assigned-clocks = <&clk IMX8MQ_VIDEO_PLL1>,
+ <&clk IMX8MQ_AUDIO_PLL1>,
+ <&clk IMX8MQ_AUDIO_PLL2>,
+ <&clk IMX8MQ_CLK_AHB>,
+ <&clk IMX8MQ_CLK_NAND_USDHC_BUS>,
+ <&clk IMX8MQ_CLK_AUDIO_AHB>,
+ <&clk IMX8MQ_VIDEO_PLL1_REF_SEL>,
+ <&clk IMX8MQ_CLK_NOC>;
+ assigned-clock-parents = <0>,
+ <0>,
+ <0>,
+ <&clk IMX8MQ_SYS1_PLL_133M>,
+ <&clk IMX8MQ_SYS1_PLL_266M>,
+ <&clk IMX8MQ_SYS2_PLL_500M>,
+ <&clk IMX8MQ_CLK_27M>,
+ <&clk IMX8MQ_SYS1_PLL_800M>;
+ assigned-clock-rates = <593999999>,
+ <786432000>,
+ <722534400>;
};
src: reset-controller@30390000 {
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH v4] arm64: dts: imx8mq: Init rates and parents configs for clocks
2019-07-28 15:20 [PATCH v4] arm64: dts: imx8mq: Init rates and parents configs for clocks Daniel Baluta
@ 2019-07-29 12:48 ` Guido Günther
2019-08-21 20:39 ` Leonard Crestez
2019-10-22 16:19 ` Guido Günther
2 siblings, 0 replies; 6+ messages in thread
From: Guido Günther @ 2019-07-29 12:48 UTC (permalink / raw)
To: Daniel Baluta
Cc: devicetree, baruch, abel.vesa, Anson.Huang, ccaione,
andrew.smirnov, festevam, s.hauer, angus, linux-kernel,
linux-imx, shawnguo, shengjiu.wang, linux-arm-kernel, l.stach
Hi,
On Sun, Jul 28, 2019 at 06:20:40PM +0300, Daniel Baluta wrote:
> From: Abel Vesa <abel.vesa@nxp.com>
>
> Add the initial configuration for clocks that need default parent and rate
> setting. This is based on the vendor tree clock provider parents and rates
> configuration except this is doing the setup in dts rather then using clock
> consumer API in a clock provider driver.
>
> Note that by adding the initial rate setting for audio_pll1/audio_pll
> setting we need to remove it from imx8mq-librem5-devkit.dts
>
> Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
> Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
> Tested-by: Angus Ainslie (Purism) <angus@akkea.ca>
> ---
> Changes since v3:
> - fix extra new lines
>
> .../dts/freescale/imx8mq-librem5-devkit.dts | 5 -----
> arch/arm64/boot/dts/freescale/imx8mq.dtsi | 19 +++++++++++++++++++
> 2 files changed, 19 insertions(+), 5 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
> index 683a11035643..c702ccc82867 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
> +++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
> @@ -169,11 +169,6 @@
> };
> };
>
> -&clk {
> - assigned-clocks = <&clk IMX8MQ_AUDIO_PLL1>, <&clk IMX8MQ_AUDIO_PLL2>;
> - assigned-clock-rates = <786432000>, <722534400>;
> -};
> -
> &dphy {
> status = "okay";
> };
> diff --git a/arch/arm64/boot/dts/freescale/imx8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
> index 02fbd0625318..a55d72ba2e05 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mq.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
> @@ -494,6 +494,25 @@
> clock-names = "ckil", "osc_25m", "osc_27m",
> "clk_ext1", "clk_ext2",
> "clk_ext3", "clk_ext4";
> + assigned-clocks = <&clk IMX8MQ_VIDEO_PLL1>,
> + <&clk IMX8MQ_AUDIO_PLL1>,
> + <&clk IMX8MQ_AUDIO_PLL2>,
> + <&clk IMX8MQ_CLK_AHB>,
> + <&clk IMX8MQ_CLK_NAND_USDHC_BUS>,
> + <&clk IMX8MQ_CLK_AUDIO_AHB>,
> + <&clk IMX8MQ_VIDEO_PLL1_REF_SEL>,
> + <&clk IMX8MQ_CLK_NOC>;
> + assigned-clock-parents = <0>,
> + <0>,
> + <0>,
> + <&clk IMX8MQ_SYS1_PLL_133M>,
> + <&clk IMX8MQ_SYS1_PLL_266M>,
> + <&clk IMX8MQ_SYS2_PLL_500M>,
> + <&clk IMX8MQ_CLK_27M>,
> + <&clk IMX8MQ_SYS1_PLL_800M>;
> + assigned-clock-rates = <593999999>,
> + <786432000>,
> + <722534400>;
> };
>
> src: reset-controller@30390000 {
Tested-by: Guido Günther <agx@sigxcpu.org>
Cheers,
-- Guido
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH v4] arm64: dts: imx8mq: Init rates and parents configs for clocks
2019-07-28 15:20 [PATCH v4] arm64: dts: imx8mq: Init rates and parents configs for clocks Daniel Baluta
2019-07-29 12:48 ` Guido Günther
@ 2019-08-21 20:39 ` Leonard Crestez
[not found] ` <1571812158.5953.2.camel@nxp.com>
2019-10-22 16:19 ` Guido Günther
2 siblings, 1 reply; 6+ messages in thread
From: Leonard Crestez @ 2019-08-21 20:39 UTC (permalink / raw)
To: Daniel Baluta, shawnguo, Abel Vesa
Cc: devicetree, baruch, Jacky Bai, Anson Huang, ccaione,
andrew.smirnov, s.hauer, angus, Stephen Boyd, linux-kernel,
linux-clk, agx, dl-linux-imx, Peng Fan, festevam, S.j. Wang,
linux-arm-kernel, l.stach
On 28.07.2019 18:20, Daniel Baluta wrote:
> From: Abel Vesa <abel.vesa@nxp.com>
>
> Add the initial configuration for clocks that need default parent and rate
> setting. This is based on the vendor tree clock provider parents and rates
> configuration except this is doing the setup in dts rather then using clock
> consumer API in a clock provider driver.
>
> Note that by adding the initial rate setting for audio_pll1/audio_pll
> setting we need to remove it from imx8mq-librem5-devkit.dts
Setting default rates for audio_pll1 and audio_pll2 in soc dtsi makes a
lot of sense to me; the intention is for one to run at a multiple of
44.1k and another at a multiple of 48k.
> diff --git a/arch/arm64/boot/dts/freescale/imx8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
> index 02fbd0625318..a55d72ba2e05 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mq.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
> @@ -494,6 +494,25 @@
> clock-names = "ckil", "osc_25m", "osc_27m",
> "clk_ext1", "clk_ext2",
> "clk_ext3", "clk_ext4";
> + assigned-clocks = <&clk IMX8MQ_VIDEO_PLL1>,
> + <&clk IMX8MQ_AUDIO_PLL1>,
> + <&clk IMX8MQ_AUDIO_PLL2>,
> + <&clk IMX8MQ_CLK_AHB>,
> + <&clk IMX8MQ_CLK_NAND_USDHC_BUS>,
> + <&clk IMX8MQ_CLK_AUDIO_AHB>,
> + <&clk IMX8MQ_VIDEO_PLL1_REF_SEL>,
> + <&clk IMX8MQ_CLK_NOC>;
> + assigned-clock-parents = <0>,
> + <0>,
> + <0> > + <&clk IMX8MQ_SYS1_PLL_133M>,
> + <&clk IMX8MQ_SYS1_PLL_266M>,
> + <&clk IMX8MQ_SYS2_PLL_500M>,
> + <&clk IMX8MQ_CLK_27M>,
> + <&clk IMX8MQ_SYS1_PLL_800M>;
> + assigned-clock-rates = <593999999>,
> + <786432000>,
> + <722534400>;
The audio PLLs should run below 650 mHz so please use 393216000 and
361267200 instead of 786432000 and 722534400. For the 8mm equivalent see
commit 053a4ffe2988 ("clk: imx: imx8mm: fix audio pll setting").
You should also move the unbypassing of AUDIO_PLL1 and AUDIO_PLL2 here
just add two more assigned-clocks and assigned-clock-parents.
--
Regards,
Leonard
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH v4] arm64: dts: imx8mq: Init rates and parents configs for clocks
2019-07-28 15:20 [PATCH v4] arm64: dts: imx8mq: Init rates and parents configs for clocks Daniel Baluta
2019-07-29 12:48 ` Guido Günther
2019-08-21 20:39 ` Leonard Crestez
@ 2019-10-22 16:19 ` Guido Günther
2019-10-25 2:31 ` Shawn Guo
2 siblings, 1 reply; 6+ messages in thread
From: Guido Günther @ 2019-10-22 16:19 UTC (permalink / raw)
To: Daniel Baluta
Cc: devicetree, baruch, abel.vesa, Anson.Huang, ccaione,
andrew.smirnov, festevam, s.hauer, angus, linux-kernel,
linux-imx, shawnguo, shengjiu.wang, linux-arm-kernel, l.stach
Hi,
On Sun, Jul 28, 2019 at 06:20:40PM +0300, Daniel Baluta wrote:
> From: Abel Vesa <abel.vesa@nxp.com>
>
> Add the initial configuration for clocks that need default parent and rate
> setting. This is based on the vendor tree clock provider parents and rates
> configuration except this is doing the setup in dts rather then using clock
> consumer API in a clock provider driver.
>
> Note that by adding the initial rate setting for audio_pll1/audio_pll
> setting we need to remove it from imx8mq-librem5-devkit.dts
It seems this never made it into any tree, any particular reason for
that?
Cheers,
-- Guido
>
> Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
> Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
> Tested-by: Angus Ainslie (Purism) <angus@akkea.ca>
> ---
> Changes since v3:
> - fix extra new lines
>
> .../dts/freescale/imx8mq-librem5-devkit.dts | 5 -----
> arch/arm64/boot/dts/freescale/imx8mq.dtsi | 19 +++++++++++++++++++
> 2 files changed, 19 insertions(+), 5 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
> index 683a11035643..c702ccc82867 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
> +++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
> @@ -169,11 +169,6 @@
> };
> };
>
> -&clk {
> - assigned-clocks = <&clk IMX8MQ_AUDIO_PLL1>, <&clk IMX8MQ_AUDIO_PLL2>;
> - assigned-clock-rates = <786432000>, <722534400>;
> -};
> -
> &dphy {
> status = "okay";
> };
> diff --git a/arch/arm64/boot/dts/freescale/imx8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
> index 02fbd0625318..a55d72ba2e05 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mq.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
> @@ -494,6 +494,25 @@
> clock-names = "ckil", "osc_25m", "osc_27m",
> "clk_ext1", "clk_ext2",
> "clk_ext3", "clk_ext4";
> + assigned-clocks = <&clk IMX8MQ_VIDEO_PLL1>,
> + <&clk IMX8MQ_AUDIO_PLL1>,
> + <&clk IMX8MQ_AUDIO_PLL2>,
> + <&clk IMX8MQ_CLK_AHB>,
> + <&clk IMX8MQ_CLK_NAND_USDHC_BUS>,
> + <&clk IMX8MQ_CLK_AUDIO_AHB>,
> + <&clk IMX8MQ_VIDEO_PLL1_REF_SEL>,
> + <&clk IMX8MQ_CLK_NOC>;
> + assigned-clock-parents = <0>,
> + <0>,
> + <0>,
> + <&clk IMX8MQ_SYS1_PLL_133M>,
> + <&clk IMX8MQ_SYS1_PLL_266M>,
> + <&clk IMX8MQ_SYS2_PLL_500M>,
> + <&clk IMX8MQ_CLK_27M>,
> + <&clk IMX8MQ_SYS1_PLL_800M>;
> + assigned-clock-rates = <593999999>,
> + <786432000>,
> + <722534400>;
> };
>
> src: reset-controller@30390000 {
> --
> 2.17.1
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH v4] arm64: dts: imx8mq: Init rates and parents configs for clocks
[not found] ` <1571812158.5953.2.camel@nxp.com>
@ 2019-10-23 8:38 ` Leonard Crestez
0 siblings, 0 replies; 6+ messages in thread
From: Leonard Crestez @ 2019-10-23 8:38 UTC (permalink / raw)
To: Viorel Suman, Abel Vesa, Peng Fan
Cc: devicetree, baruch, s.hauer, Jacky Bai, Anson Huang, ccaione,
andrew.smirnov, Daniel Baluta, agx, angus, sboyd, linux-kernel,
linux-clk, dl-linux-imx, festevam, shawnguo, S.j. Wang,
linux-arm-kernel, l.stach
On 2019-10-23 9:29 AM, Viorel Suman wrote:
> On Mi, 2019-08-21 at 20:39 +0000, Leonard Crestez wrote:
>> The audio PLLs should run below 650 mHz so please use 393216000 and
>> 361267200 instead of 786432000 and 722534400. For the 8mm equivalent see
>> commit 053a4ffe2988 ("clk: imx: imx8mm: fix audio pll setting").
>
> Hi Leonard,
>
> Audio PLL IP on 8mm and 8mn is different than the Audio PLL IP on 8mq,
> so the requirement to run below 650 MHZ may not apply to 8mq.
This "max 650mHz" limit is from internal ADD and is also mentioned for
imx8mq.
Peng: you made the change in our internal tree, can you confirm this
requirement also applies to 8mq?
Viorel: Is there any impact from 393216000 vs 786432000 on PLL on audio?
As far as I can know this rate goes through various dividers anyway.
--
Regards,
Leonard
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH v4] arm64: dts: imx8mq: Init rates and parents configs for clocks
2019-10-22 16:19 ` Guido Günther
@ 2019-10-25 2:31 ` Shawn Guo
0 siblings, 0 replies; 6+ messages in thread
From: Shawn Guo @ 2019-10-25 2:31 UTC (permalink / raw)
To: Guido Günther
Cc: devicetree, baruch, abel.vesa, Anson.Huang, ccaione,
andrew.smirnov, festevam, s.hauer, angus, linux-kernel,
linux-imx, Daniel Baluta, shengjiu.wang, linux-arm-kernel,
l.stach
On Tue, Oct 22, 2019 at 06:19:19PM +0200, Guido Günther wrote:
> Hi,
> On Sun, Jul 28, 2019 at 06:20:40PM +0300, Daniel Baluta wrote:
> > From: Abel Vesa <abel.vesa@nxp.com>
> >
> > Add the initial configuration for clocks that need default parent and rate
> > setting. This is based on the vendor tree clock provider parents and rates
> > configuration except this is doing the setup in dts rather then using clock
> > consumer API in a clock provider driver.
> >
> > Note that by adding the initial rate setting for audio_pll1/audio_pll
> > setting we need to remove it from imx8mq-librem5-devkit.dts
>
> It seems this never made it into any tree, any particular reason for
> that?
There is some discussion going on and I haven't seen it reaches an
explicit agreement.
Shawn
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2019-10-25 2:31 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-07-28 15:20 [PATCH v4] arm64: dts: imx8mq: Init rates and parents configs for clocks Daniel Baluta
2019-07-29 12:48 ` Guido Günther
2019-08-21 20:39 ` Leonard Crestez
[not found] ` <1571812158.5953.2.camel@nxp.com>
2019-10-23 8:38 ` Leonard Crestez
2019-10-22 16:19 ` Guido Günther
2019-10-25 2:31 ` Shawn Guo
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).