[PATCH v2 0/4] Add USB 3 support for H6 and Orange Pi 3

[PATCH v2 0/4] Add USB 3 support for H6 and Orange Pi 3

[Ondrej Jirman]

This series implements USB 3 support for Xunlong Orange Pi 3 board.

This is a re-hash of the Icenowy's earlier USB3 work[1] without code
that caused controversy previously. Orange Pi 3 board doesn't need vbus
supply to be dynamically enabled, so that code is not needed to support
USB3 on this board.

Most of patches are already reviewed. I've converted dt-bindings to yaml
format, and added the Orange Pi 3 board modifications.

Hopefully with this series we can get USB3 support into mainline for
Orange Pi 3, and build on it later to support more boards, where
supporting them is more complicated.

Please take a look.

thank you and regards,
  Ondrej Jirman

[1] https://lore.kernel.org/patchwork/patch/1058919/

Changes in v2:
- Added Maxime's Acked-By's
- Fixed title of DT bindings file

Changes since Icenowy v5 series:
- use earlier patches that did not include VBUS regulator/connector
  code
- converted dt bindings to yaml
- added patch to enable usb3 on Orange Pi 3

Icenowy Zheng (2):
  phy: allwinner: add phy driver for USB3 PHY on Allwinner H6 SoC
  arm64: dts: allwinner: h6: add USB3 device nodes

Ondrej Jirman (2):
  dt-bindings: Add bindings for USB3 phy on Allwinner H6
  arm64: dts: allwinner: orange-pi-3: Enable USB 3.0 host support

 .../phy/allwinner,sun50i-h6-usb3-phy.yaml     |  47 +++++
 .../dts/allwinner/sun50i-h6-orangepi-3.dts    |   8 +
 arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi  |  32 +++
 drivers/phy/allwinner/Kconfig                 |  12 ++
 drivers/phy/allwinner/Makefile                |   1 +
 drivers/phy/allwinner/phy-sun50i-usb3.c       | 195 ++++++++++++++++++
 6 files changed, 295 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/phy/allwinner,sun50i-h6-usb3-phy.yaml
 create mode 100644 drivers/phy/allwinner/phy-sun50i-usb3.c

-- 
2.23.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 1/4] dt-bindings: Add bindings for USB3 phy on Allwinner H6

[Ondrej Jirman]

The new Allwinner H6 SoC contains a USB3 PHY that is wired to the
external USB3 pins of the SoC.

Add a device tree binding for the PHY.

Signed-off-by: Ondrej Jirman <megous@megous.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
---
 .../phy/allwinner,sun50i-h6-usb3-phy.yaml     | 47 +++++++++++++++++++
 1 file changed, 47 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/phy/allwinner,sun50i-h6-usb3-phy.yaml

diff --git a/Documentation/devicetree/bindings/phy/allwinner,sun50i-h6-usb3-phy.yaml b/Documentation/devicetree/bindings/phy/allwinner,sun50i-h6-usb3-phy.yaml
new file mode 100644
index 000000000000..e5922b427342
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/allwinner,sun50i-h6-usb3-phy.yaml
@@ -0,0 +1,47 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+# Copyright 2019 Ondrej Jirman <megous@megous.com>
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/phy/allwinner,sun50i-h6-usb3-phy.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Allwinner H6 USB3 PHY
+
+maintainers:
+  - Ondrej Jirman <megous@megous.com>
+
+properties:
+  compatible:
+    enum:
+      - allwinner,sun50i-h6-usb3-phy
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  resets:
+    maxItems: 1
+
+  "#phy-cells":
+    const: 0
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - resets
+  - "#phy-cells"
+
+examples:
+  - |
+    #include <dt-bindings/clock/sun50i-h6-ccu.h>
+    #include <dt-bindings/reset/sun50i-h6-ccu.h>
+    phy@5210000 {
+          compatible = "allwinner,sun50i-h6-usb3-phy";
+          reg = <0x5210000 0x10000>;
+          clocks = <&ccu CLK_USB_PHY1>;
+          resets = <&ccu RST_USB_PHY1>;
+          #phy-cells = <0>;
+    };
-- 
2.23.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 1/4] dt-bindings: Add bindings for USB3 phy on Allwinner H6

[Rob Herring]

On Thu, 24 Oct 2019 12:54:57 +0200, Ondrej Jirman wrote:
> The new Allwinner H6 SoC contains a USB3 PHY that is wired to the
> external USB3 pins of the SoC.
> 
> Add a device tree binding for the PHY.
> 
> Signed-off-by: Ondrej Jirman <megous@megous.com>
> Acked-by: Maxime Ripard <mripard@kernel.org>
> ---
>  .../phy/allwinner,sun50i-h6-usb3-phy.yaml     | 47 +++++++++++++++++++
>  1 file changed, 47 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/phy/allwinner,sun50i-h6-usb3-phy.yaml
> 

Reviewed-by: Rob Herring <robh@kernel.org>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 2/4] phy: allwinner: add phy driver for USB3 PHY on Allwinner H6 SoC

[Ondrej Jirman]

From: Icenowy Zheng <icenowy@aosc.io>

Allwinner H6 SoC contains a USB3 PHY (with USB2 DP/DM lines also
controlled).

Add a driver for it.

The register operations in this driver is mainly extracted from the BSP
USB3 driver.

Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
---
 drivers/phy/allwinner/Kconfig           |  12 ++
 drivers/phy/allwinner/Makefile          |   1 +
 drivers/phy/allwinner/phy-sun50i-usb3.c | 195 ++++++++++++++++++++++++
 3 files changed, 208 insertions(+)
 create mode 100644 drivers/phy/allwinner/phy-sun50i-usb3.c

diff --git a/drivers/phy/allwinner/Kconfig b/drivers/phy/allwinner/Kconfig
index 215425296c77..fcae35ddd430 100644
--- a/drivers/phy/allwinner/Kconfig
+++ b/drivers/phy/allwinner/Kconfig
@@ -45,3 +45,15 @@ config PHY_SUN9I_USB
 	  sun9i SoCs.
 
 	  This driver controls each individual USB 2 host PHY.
+
+config PHY_SUN50I_USB3
+	tristate "Allwinner sun50i SoC USB3 PHY driver"
+	depends on ARCH_SUNXI && HAS_IOMEM && OF
+	depends on RESET_CONTROLLER
+	select USB_COMMON
+	select GENERIC_PHY
+	help
+	  Enable this to support the USB3.0-capable transceiver that is
+	  part of some Allwinner sun50i SoCs.
+
+	  This driver controls each individual USB 2+3 host PHY combo.
diff --git a/drivers/phy/allwinner/Makefile b/drivers/phy/allwinner/Makefile
index 799a65c0b58d..bd74901a1255 100644
--- a/drivers/phy/allwinner/Makefile
+++ b/drivers/phy/allwinner/Makefile
@@ -2,3 +2,4 @@
 obj-$(CONFIG_PHY_SUN4I_USB)		+= phy-sun4i-usb.o
 obj-$(CONFIG_PHY_SUN6I_MIPI_DPHY)	+= phy-sun6i-mipi-dphy.o
 obj-$(CONFIG_PHY_SUN9I_USB)		+= phy-sun9i-usb.o
+obj-$(CONFIG_PHY_SUN50I_USB3)		+= phy-sun50i-usb3.o
diff --git a/drivers/phy/allwinner/phy-sun50i-usb3.c b/drivers/phy/allwinner/phy-sun50i-usb3.c
new file mode 100644
index 000000000000..8e170a4d0a11
--- /dev/null
+++ b/drivers/phy/allwinner/phy-sun50i-usb3.c
@@ -0,0 +1,195 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Allwinner sun50i(H6) USB 3.0 phy driver
+ *
+ * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
+ *
+ * Based on phy-sun9i-usb.c, which is:
+ *
+ * Copyright (C) 2014-2015 Chen-Yu Tsai <wens@csie.org>
+ *
+ * Based on code from Allwinner BSP, which is:
+ *
+ * Copyright (c) 2010-2015 Allwinner Technology Co., Ltd.
+ */
+
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/phy/phy.h>
+#include <linux/usb/of.h>
+#include <linux/platform_device.h>
+#include <linux/reset.h>
+
+/* Interface Status and Control Registers */
+#define SUNXI_ISCR			0x00
+#define SUNXI_PIPE_CLOCK_CONTROL	0x14
+#define SUNXI_PHY_TUNE_LOW		0x18
+#define SUNXI_PHY_TUNE_HIGH		0x1c
+#define SUNXI_PHY_EXTERNAL_CONTROL	0x20
+
+/* USB2.0 Interface Status and Control Register */
+#define SUNXI_ISCR_FORCE_VBUS		(3 << 12)
+
+/* PIPE Clock Control Register */
+#define SUNXI_PCC_PIPE_CLK_OPEN		(1 << 6)
+
+/* PHY External Control Register */
+#define SUNXI_PEC_EXTERN_VBUS		(3 << 1)
+#define SUNXI_PEC_SSC_EN		(1 << 24)
+#define SUNXI_PEC_REF_SSP_EN		(1 << 26)
+
+/* PHY Tune High Register */
+#define SUNXI_TX_DEEMPH_3P5DB(n)	((n) << 19)
+#define SUNXI_TX_DEEMPH_3P5DB_MASK	GENMASK(24, 19)
+#define SUNXI_TX_DEEMPH_6DB(n)		((n) << 13)
+#define SUNXI_TX_DEEMPH_6GB_MASK	GENMASK(18, 13)
+#define SUNXI_TX_SWING_FULL(n)		((n) << 6)
+#define SUNXI_TX_SWING_FULL_MASK	GENMASK(12, 6)
+#define SUNXI_LOS_BIAS(n)		((n) << 3)
+#define SUNXI_LOS_BIAS_MASK		GENMASK(5, 3)
+#define SUNXI_TXVBOOSTLVL(n)		((n) << 0)
+#define SUNXI_TXVBOOSTLVL_MASK		GENMASK(0, 2)
+
+struct sun50i_usb3_phy {
+	struct phy *phy;
+	void __iomem *regs;
+	struct reset_control *reset;
+	struct clk *clk;
+};
+
+static void sun50i_usb3_phy_open(struct sun50i_usb3_phy *phy)
+{
+	u32 val;
+
+	val = readl(phy->regs + SUNXI_PHY_EXTERNAL_CONTROL);
+	val |= SUNXI_PEC_EXTERN_VBUS;
+	val |= SUNXI_PEC_SSC_EN | SUNXI_PEC_REF_SSP_EN;
+	writel(val, phy->regs + SUNXI_PHY_EXTERNAL_CONTROL);
+
+	val = readl(phy->regs + SUNXI_PIPE_CLOCK_CONTROL);
+	val |= SUNXI_PCC_PIPE_CLK_OPEN;
+	writel(val, phy->regs + SUNXI_PIPE_CLOCK_CONTROL);
+
+	val = readl(phy->regs + SUNXI_ISCR);
+	val |= SUNXI_ISCR_FORCE_VBUS;
+	writel(val, phy->regs + SUNXI_ISCR);
+
+	/*
+	 * All the magic numbers written to the PHY_TUNE_{LOW_HIGH}
+	 * registers are directly taken from the BSP USB3 driver from
+	 * Allwiner.
+	 */
+	writel(0x0047fc87, phy->regs + SUNXI_PHY_TUNE_LOW);
+
+	val = readl(phy->regs + SUNXI_PHY_TUNE_HIGH);
+	val &= ~(SUNXI_TXVBOOSTLVL_MASK | SUNXI_LOS_BIAS_MASK |
+		 SUNXI_TX_SWING_FULL_MASK | SUNXI_TX_DEEMPH_6GB_MASK |
+		 SUNXI_TX_DEEMPH_3P5DB_MASK);
+	val |= SUNXI_TXVBOOSTLVL(0x7);
+	val |= SUNXI_LOS_BIAS(0x7);
+	val |= SUNXI_TX_SWING_FULL(0x55);
+	val |= SUNXI_TX_DEEMPH_6DB(0x20);
+	val |= SUNXI_TX_DEEMPH_3P5DB(0x15);
+	writel(val, phy->regs + SUNXI_PHY_TUNE_HIGH);
+}
+
+static int sun50i_usb3_phy_init(struct phy *_phy)
+{
+	struct sun50i_usb3_phy *phy = phy_get_drvdata(_phy);
+	int ret;
+
+	ret = clk_prepare_enable(phy->clk);
+	if (ret)
+		goto err_clk;
+
+	ret = reset_control_deassert(phy->reset);
+	if (ret)
+		goto err_reset;
+
+	sun50i_usb3_phy_open(phy);
+	return 0;
+
+err_reset:
+	clk_disable_unprepare(phy->clk);
+
+err_clk:
+	return ret;
+}
+
+static int sun50i_usb3_phy_exit(struct phy *_phy)
+{
+	struct sun50i_usb3_phy *phy = phy_get_drvdata(_phy);
+
+	reset_control_assert(phy->reset);
+	clk_disable_unprepare(phy->clk);
+
+	return 0;
+}
+
+static const struct phy_ops sun50i_usb3_phy_ops = {
+	.init		= sun50i_usb3_phy_init,
+	.exit		= sun50i_usb3_phy_exit,
+	.owner		= THIS_MODULE,
+};
+
+static int sun50i_usb3_phy_probe(struct platform_device *pdev)
+{
+	struct sun50i_usb3_phy *phy;
+	struct device *dev = &pdev->dev;
+	struct phy_provider *phy_provider;
+	struct resource *res;
+
+	phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
+	if (!phy)
+		return -ENOMEM;
+
+	phy->clk = devm_clk_get(dev, NULL);
+	if (IS_ERR(phy->clk)) {
+		if (PTR_ERR(phy->clk) != -EPROBE_DEFER)
+			dev_err(dev, "failed to get phy clock\n");
+		return PTR_ERR(phy->clk);
+	}
+
+	phy->reset = devm_reset_control_get(dev, NULL);
+	if (IS_ERR(phy->reset)) {
+		dev_err(dev, "failed to get reset control\n");
+		return PTR_ERR(phy->reset);
+	}
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	phy->regs = devm_ioremap_resource(dev, res);
+	if (IS_ERR(phy->regs))
+		return PTR_ERR(phy->regs);
+
+	phy->phy = devm_phy_create(dev, NULL, &sun50i_usb3_phy_ops);
+	if (IS_ERR(phy->phy)) {
+		dev_err(dev, "failed to create PHY\n");
+		return PTR_ERR(phy->phy);
+	}
+
+	phy_set_drvdata(phy->phy, phy);
+	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+
+	return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static const struct of_device_id sun50i_usb3_phy_of_match[] = {
+	{ .compatible = "allwinner,sun50i-h6-usb3-phy" },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, sun50i_usb3_phy_of_match);
+
+static struct platform_driver sun50i_usb3_phy_driver = {
+	.probe	= sun50i_usb3_phy_probe,
+	.driver = {
+		.of_match_table	= sun50i_usb3_phy_of_match,
+		.name  = "sun50i-usb3-phy",
+	}
+};
+module_platform_driver(sun50i_usb3_phy_driver);
+
+MODULE_DESCRIPTION("Allwinner sun50i USB 3.0 phy driver");
+MODULE_AUTHOR("Icenowy Zheng <icenowy@aosc.io>");
+MODULE_LICENSE("GPL");
-- 
2.23.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 2/4] phy: allwinner: add phy driver for USB3 PHY on Allwinner H6 SoC

[Kishon Vijay Abraham I]

Hi,

On 24/10/19 4:24 PM, Ondrej Jirman wrote:
> From: Icenowy Zheng <icenowy@aosc.io>
> 
> Allwinner H6 SoC contains a USB3 PHY (with USB2 DP/DM lines also
> controlled).
> 
> Add a driver for it.
> 
> The register operations in this driver is mainly extracted from the BSP
> USB3 driver.
> 
> Signed-off-by: Ondrej Jirman <megous@megous.com>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> Reviewed-by: Chen-Yu Tsai <wens@csie.org>
> Acked-by: Maxime Ripard <mripard@kernel.org>
> ---
>  drivers/phy/allwinner/Kconfig           |  12 ++
>  drivers/phy/allwinner/Makefile          |   1 +
>  drivers/phy/allwinner/phy-sun50i-usb3.c | 195 ++++++++++++++++++++++++
>  3 files changed, 208 insertions(+)
>  create mode 100644 drivers/phy/allwinner/phy-sun50i-usb3.c
> 
> diff --git a/drivers/phy/allwinner/Kconfig b/drivers/phy/allwinner/Kconfig
> index 215425296c77..fcae35ddd430 100644
> --- a/drivers/phy/allwinner/Kconfig
> +++ b/drivers/phy/allwinner/Kconfig
> @@ -45,3 +45,15 @@ config PHY_SUN9I_USB
>  	  sun9i SoCs.
>  
>  	  This driver controls each individual USB 2 host PHY.
> +
> +config PHY_SUN50I_USB3
> +	tristate "Allwinner sun50i SoC USB3 PHY driver"
> +	depends on ARCH_SUNXI && HAS_IOMEM && OF
> +	depends on RESET_CONTROLLER
> +	select USB_COMMON

Looks like USB_COMMON is not required here.
> +	select GENERIC_PHY
> +	help
> +	  Enable this to support the USB3.0-capable transceiver that is
> +	  part of some Allwinner sun50i SoCs.
> +
> +	  This driver controls each individual USB 2+3 host PHY combo.
> diff --git a/drivers/phy/allwinner/Makefile b/drivers/phy/allwinner/Makefile
> index 799a65c0b58d..bd74901a1255 100644
> --- a/drivers/phy/allwinner/Makefile
> +++ b/drivers/phy/allwinner/Makefile
> @@ -2,3 +2,4 @@
>  obj-$(CONFIG_PHY_SUN4I_USB)		+= phy-sun4i-usb.o
>  obj-$(CONFIG_PHY_SUN6I_MIPI_DPHY)	+= phy-sun6i-mipi-dphy.o
>  obj-$(CONFIG_PHY_SUN9I_USB)		+= phy-sun9i-usb.o
> +obj-$(CONFIG_PHY_SUN50I_USB3)		+= phy-sun50i-usb3.o
> diff --git a/drivers/phy/allwinner/phy-sun50i-usb3.c b/drivers/phy/allwinner/phy-sun50i-usb3.c
> new file mode 100644
> index 000000000000..8e170a4d0a11
> --- /dev/null
> +++ b/drivers/phy/allwinner/phy-sun50i-usb3.c
> @@ -0,0 +1,195 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Allwinner sun50i(H6) USB 3.0 phy driver
> + *
> + * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
> + *
> + * Based on phy-sun9i-usb.c, which is:
> + *
> + * Copyright (C) 2014-2015 Chen-Yu Tsai <wens@csie.org>
> + *
> + * Based on code from Allwinner BSP, which is:
> + *
> + * Copyright (c) 2010-2015 Allwinner Technology Co., Ltd.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/err.h>
> +#include <linux/io.h>
> +#include <linux/module.h>
> +#include <linux/phy/phy.h>
> +#include <linux/usb/of.h>

this too..

Thanks
Kishon

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 3/4] arm64: dts: allwinner: h6: add USB3 device nodes

[Ondrej Jirman]

From: Icenowy Zheng <icenowy@aosc.io>

Allwinner H6 SoC features USB3 functionality, with a DWC3 controller and
a custom PHY.

Add device tree nodes for them.

Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
---
 arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 32 ++++++++++++++++++++
 1 file changed, 32 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
index 0d5ea19336a1..80233db478e6 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
@@ -537,6 +537,38 @@
 			status = "disabled";
 		};
 
+		dwc3: dwc3@5200000 {
+			compatible = "snps,dwc3";
+			reg = <0x05200000 0x10000>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_XHCI>,
+				 <&ccu CLK_BUS_XHCI>,
+				 <&rtc 0>;
+			clock-names = "ref", "bus_early", "suspend";
+			resets = <&ccu RST_BUS_XHCI>;
+			/*
+			 * The datasheet of the chip doesn't declare the
+			 * peripheral function, and there's no boards known
+			 * to have a USB Type-B port routed to the port.
+			 * In addition, no one has tested the peripheral
+			 * function yet.
+			 * So set the dr_mode to "host" in the DTSI file.
+			 */
+			dr_mode = "host";
+			phys = <&usb3phy>;
+			phy-names = "usb3-phy";
+			status = "disabled";
+		};
+
+		usb3phy: phy@5210000 {
+			compatible = "allwinner,sun50i-h6-usb3-phy";
+			reg = <0x5210000 0x10000>;
+			clocks = <&ccu CLK_USB_PHY1>;
+			resets = <&ccu RST_USB_PHY1>;
+			#phy-cells = <0>;
+			status = "disabled";
+		};
+
 		ehci3: usb@5311000 {
 			compatible = "allwinner,sun50i-h6-ehci", "generic-ehci";
 			reg = <0x05311000 0x100>;
-- 
2.23.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 4/4] arm64: dts: allwinner: orange-pi-3: Enable USB 3.0 host support

[Ondrej Jirman]

Enable Allwinner's USB 3.0 phy and the host controller. Orange Pi 3
board has GL3510 USB 3.0 4-port hub connected to the SoC's USB 3.0
port. All four ports are exposed via USB3-A connectors. VBUS is
always on, since it's powered directly from DCIN (VCC-5V) and
not switchable.

Signed-off-by: Ondrej Jirman <megous@megous.com>
---
 arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts
index eb379cd402ac..259af5b0f1a7 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts
@@ -94,6 +94,10 @@
 	status = "okay";
 };
 
+&dwc3 {
+	status = "okay";
+};
+
 &ehci0 {
 	status = "okay";
 };
@@ -285,3 +289,7 @@
 	usb3_vbus-supply = <&reg_vcc5v>;
 	status = "okay";
 };
+
+&usb3phy {
+	status = "okay";
+};
-- 
2.23.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel