[PATCH v3 0/5] Add support for PinePhone LCD panel

[PATCH v3 0/5] Add support for PinePhone LCD panel

[Ondrej Jirman]

This patchset adds support for the LCD panel of PinePhone.

The first 3 patches are for the panel itself, and the last 2 patches are
for enabling it on PinePhone.

I've tested this on PinePhone 1.0 and 1.2.

Please take a look.

thank you and regards,
  Ondrej Jirman


Changes in v3:
- Panel driver renamed to the name of the LCD controller
- Re-organize the driver slightly to more easily support more panels
  based on the same controller.
- Add patch to enable the touchscreen to complete the LCD support
  on PinePhone.
- Dropped the "DSI fix" patch (the driver seems to work for me without it)
- Improved brightness levels handling:
  - PinePhone 1.0 uses default levels generated by the driver
  - On PinePhone 1.1 duty cycles < 20% lead to black screen, so
    default levels can't be used. Martijn Braam came up with a
    list of duty cycle values that lead to perception of linear
    brigtness level <-> light intensity on PinePhone 1.1
- There was some feedback on v2 about this being similar to st7701.
  It's only similar in name. Most of the "user commands" are different,
  so I opted to keep this in a new driver instead of creating st770x.
  
  Anyone who likes to check the differences, here are datasheets:

  - https://megous.com/dl/tmp/ST7703_DS_v01_20160128.pdf
  - https://megous.com/dl/tmp/ST7701.pdf

Changes in v2:
- DT Example fix.
- DT Format fix.
- Raised copyright info to 2020.
- Sort panel operation functions.
- Sort inclusion.


-- For phone owners: --

There's an open question on how to set the backlight brightness values
on post 1.0 revision phone, since lower duty cycles (< 10-20%) lead
to backlight being black. It would be nice if more people can test
the various backlight levels on 1.1 and 1.2 revision with this change
in dts:

       brightness-levels = <0 1000>;
       num-interpolated-steps = <1000>;

and report at what brightness level the backlight turns on. So far it
seems this has a wide range. Lowest useable duty cycle for me is ~7%
on 1.2 and for Martijn ~20% on 1.1.

Icenowy Zheng (4):
  dt-bindings: vendor-prefixes: Add Xingbangda
  dt-bindings: panel: Add binding for Xingbangda XBD599 panel
  drm: panel: Add Xingbangda XBD599 panel (ST7703 controller)
  arm64: dts: sun50i-a64-pinephone: Enable LCD support on PinePhone

Ondrej Jirman (1):
  arm64: dts: sun50i-a64-pinephone: Add touchscreen support

 .../display/panel/sitronix,st7703.yaml        |  63 +++
 .../devicetree/bindings/vendor-prefixes.yaml  |   2 +
 .../allwinner/sun50i-a64-pinephone-1.1.dts    |  19 +
 .../dts/allwinner/sun50i-a64-pinephone.dtsi   |  54 +++
 drivers/gpu/drm/panel/Kconfig                 |  10 +
 drivers/gpu/drm/panel/Makefile                |   1 +
 drivers/gpu/drm/panel/panel-sitronix-st7703.c | 386 ++++++++++++++++++
 7 files changed, 535 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/panel/sitronix,st7703.yaml
 create mode 100644 drivers/gpu/drm/panel/panel-sitronix-st7703.c

-- 
2.26.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 1/5] dt-bindings: vendor-prefixes: Add Xingbangda

[Ondrej Jirman]

From: Icenowy Zheng <icenowy@aosc.io>

Shenzhen Xingbangda Display Technology Co., Ltd is a company which
produces LCD modules. It supplies the LCD panels for the PinePhone.

Add the vendor prefix of it.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Ondrej Jirman <megous@megous.com>
---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 442579a4c837..7504440dba36 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -1139,6 +1139,8 @@ patternProperties:
     description: Xiaomi Technology Co., Ltd.
   "^xillybus,.*":
     description: Xillybus Ltd.
+  "^xingbangda,.*":
+    description: Shenzhen Xingbangda Display Technology Co., Ltd
   "^xinpeng,.*":
     description: Shenzhen Xinpeng Technology Co., Ltd
   "^xlnx,.*":
-- 
2.26.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 1/5] dt-bindings: vendor-prefixes: Add Xingbangda

[Rob Herring]

On Wed, 13 May 2020 23:24:47 +0200, Ondrej Jirman wrote:
> From: Icenowy Zheng <icenowy@aosc.io>
> 
> Shenzhen Xingbangda Display Technology Co., Ltd is a company which
> produces LCD modules. It supplies the LCD panels for the PinePhone.
> 
> Add the vendor prefix of it.
> 
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> Signed-off-by: Ondrej Jirman <megous@megous.com>
> ---
>  Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
>  1 file changed, 2 insertions(+)
> 

Acked-by: Rob Herring <robh@kernel.org>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 2/5] dt-bindings: panel: Add binding for Xingbangda XBD599 panel

[Ondrej Jirman]

From: Icenowy Zheng <icenowy@aosc.io>

Xingbangda XBD599 is a 5.99" 720x1440 MIPI-DSI LCD panel. It is based on
Sitronix ST7703 LCD controller.

Add its device tree binding.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Ondrej Jirman <megous@megous.com>
---
 .../display/panel/sitronix,st7703.yaml        | 63 +++++++++++++++++++
 1 file changed, 63 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/panel/sitronix,st7703.yaml

diff --git a/Documentation/devicetree/bindings/display/panel/sitronix,st7703.yaml b/Documentation/devicetree/bindings/display/panel/sitronix,st7703.yaml
new file mode 100644
index 000000000000..6e1606db4ab4
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/sitronix,st7703.yaml
@@ -0,0 +1,63 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/sitronix,st7703.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Sitronix ST7703 MIPI DSI panel
+
+maintainers:
+  - Icenowy Zheng <icenowy@aosc.io>
+  - Ondrej Jirman <megous@megous.com>
+
+allOf:
+  - $ref: panel-common.yaml#
+
+properties:
+  compatible:
+    items:
+      - enum:
+        - xingbangda,xbd599
+      - const: sitronix,st7703
+
+  reg:
+    description: DSI virtual channel used by that screen
+    maxItems: 1
+
+  vcc-supply:
+    description: regulator that supplies the VCC voltage
+
+  iovcc-supply:
+    description: regulator that supplies the IOVCC voltage
+
+  reset-gpios: true
+
+  backlight: true
+
+required:
+  - compatible
+  - reg
+  - vcc-supply
+  - iovcc-supply
+  - reset-gpios
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    dsi {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        panel@0 {
+            compatible = "xingbangda,xbd599", "sitronix,st7703";
+            reg = <0>;
+            reset-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* LCD-RST: PD24 */
+            iovcc-supply = <&reg_dldo2>;
+            vcc-supply = <&reg_ldo_io0>;
+            backlight = <&backlight>;
+        };
+    };
+
-- 
2.26.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 2/5] dt-bindings: panel: Add binding for Xingbangda XBD599 panel

[Linus Walleij]

On Wed, May 13, 2020 at 11:24 PM Ondrej Jirman <megous@megous.com> wrote:

> From: Icenowy Zheng <icenowy@aosc.io>
>
> Xingbangda XBD599 is a 5.99" 720x1440 MIPI-DSI LCD panel. It is based on
> Sitronix ST7703 LCD controller.
>
> Add its device tree binding.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> Signed-off-by: Ondrej Jirman <megous@megous.com>

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

Yours,
Linus Walleij

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 2/5] dt-bindings: panel: Add binding for Xingbangda XBD599 panel

[Rob Herring]

On Wed, 13 May 2020 23:24:48 +0200, Ondrej Jirman wrote:
> From: Icenowy Zheng <icenowy@aosc.io>
> 
> Xingbangda XBD599 is a 5.99" 720x1440 MIPI-DSI LCD panel. It is based on
> Sitronix ST7703 LCD controller.
> 
> Add its device tree binding.
> 
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> Signed-off-by: Ondrej Jirman <megous@megous.com>
> ---
>  .../display/panel/sitronix,st7703.yaml        | 63 +++++++++++++++++++
>  1 file changed, 63 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/display/panel/sitronix,st7703.yaml
> 

Reviewed-by: Rob Herring <robh@kernel.org>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 3/5] drm: panel: Add Xingbangda XBD599 panel (ST7703 controller)

[Ondrej Jirman]

From: Icenowy Zheng <icenowy@aosc.io>

Xingbangda XBD599 is a 5.99" 720x1440 MIPI-DSI IPS LCD panel made by
Xingbangda, which is used on PinePhone final assembled phones.

It is based on Sitronix ST7703 LCD controller.

Add support for it.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Ondrej Jirman <megous@megous.com>
---
 drivers/gpu/drm/panel/Kconfig                 |  10 +
 drivers/gpu/drm/panel/Makefile                |   1 +
 drivers/gpu/drm/panel/panel-sitronix-st7703.c | 386 ++++++++++++++++++
 3 files changed, 397 insertions(+)
 create mode 100644 drivers/gpu/drm/panel/panel-sitronix-st7703.c

diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
index 39055c1f0e2f..b7bc157b0612 100644
--- a/drivers/gpu/drm/panel/Kconfig
+++ b/drivers/gpu/drm/panel/Kconfig
@@ -395,6 +395,16 @@ config DRM_PANEL_SITRONIX_ST7701
 	  ST7701 controller for 480X864 LCD panels with MIPI/RGB/SPI
 	  system interfaces.
 
+config DRM_PANEL_SITRONIX_ST7703
+	tristate "Sitronix ST7703 panel driver"
+	depends on OF
+	depends on DRM_MIPI_DSI
+	depends on BACKLIGHT_CLASS_DEVICE
+	help
+	  Say Y here if you want to enable support for the Sitronix
+	  ST7703 controller for 720X1440 LCD panels with MIPI/RGB/SPI
+	  system interfaces.
+
 config DRM_PANEL_SITRONIX_ST7789V
 	tristate "Sitronix ST7789V panel"
 	depends on OF && SPI
diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile
index de74f282c433..47f4789a8685 100644
--- a/drivers/gpu/drm/panel/Makefile
+++ b/drivers/gpu/drm/panel/Makefile
@@ -41,6 +41,7 @@ obj-$(CONFIG_DRM_PANEL_SHARP_LQ101R1SX01) += panel-sharp-lq101r1sx01.o
 obj-$(CONFIG_DRM_PANEL_SHARP_LS037V7DW01) += panel-sharp-ls037v7dw01.o
 obj-$(CONFIG_DRM_PANEL_SHARP_LS043T1LE01) += panel-sharp-ls043t1le01.o
 obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7701) += panel-sitronix-st7701.o
+obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7703) += panel-sitronix-st7703.o
 obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7789V) += panel-sitronix-st7789v.o
 obj-$(CONFIG_DRM_PANEL_SONY_ACX424AKP) += panel-sony-acx424akp.o
 obj-$(CONFIG_DRM_PANEL_SONY_ACX565AKM) += panel-sony-acx565akm.o
diff --git a/drivers/gpu/drm/panel/panel-sitronix-st7703.c b/drivers/gpu/drm/panel/panel-sitronix-st7703.c
new file mode 100644
index 000000000000..092dd73c86d0
--- /dev/null
+++ b/drivers/gpu/drm/panel/panel-sitronix-st7703.c
@@ -0,0 +1,386 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * DRM driver for Sitronix ST7703 MIPI DSI panel
+ *
+ * Copyright (C) 2020 Ondrej Jirman <megous@megous.com>
+ * Copyright (C) 2019-2020 Icenowy Zheng <icenowy@aosc.io>
+ *
+ * Based on panel-rocktech-jh057n00900.c, which is:
+ *   Copyright (C) Purism SPC 2019
+ */
+
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/regulator/consumer.h>
+
+#include <drm/drm_mipi_dsi.h>
+#include <drm/drm_modes.h>
+#include <drm/drm_panel.h>
+#include <drm/drm_print.h>
+
+/* Manufacturer specific Commands send via DSI */
+#define ST7703_CMD_ALL_PIXEL_OFF 0x22
+#define ST7703_CMD_ALL_PIXEL_ON	 0x23
+#define ST7703_CMD_SETDISP	 0xB2
+#define ST7703_CMD_SETRGBIF	 0xB3
+#define ST7703_CMD_SETCYC	 0xB4
+#define ST7703_CMD_SETBGP	 0xB5
+#define ST7703_CMD_SETVCOM	 0xB6
+#define ST7703_CMD_SETOTP	 0xB7
+#define ST7703_CMD_SETPOWER_EXT	 0xB8
+#define ST7703_CMD_SETEXTC	 0xB9
+#define ST7703_CMD_SETMIPI	 0xBA
+#define ST7703_CMD_SETVDC	 0xBC
+#define ST7703_CMD_SETSCR	 0xC0
+#define ST7703_CMD_SETPOWER	 0xC1
+#define ST7703_CMD_UNK_C6	 0xC6
+#define ST7703_CMD_SETPANEL	 0xCC
+#define ST7703_CMD_SETGAMMA	 0xE0
+#define ST7703_CMD_SETEQ	 0xE3
+#define ST7703_CMD_SETGIP1	 0xE9
+#define ST7703_CMD_SETGIP2	 0xEA
+
+struct st7703_panel_desc {
+	const struct drm_display_mode *mode;
+	unsigned int lanes;
+	unsigned long flags;
+	enum mipi_dsi_pixel_format format;
+	const char *const *supply_names;
+	unsigned int num_supplies;
+};
+
+struct st7703 {
+	struct device *dev;
+	struct drm_panel panel;
+	struct gpio_desc *reset_gpio;
+	struct regulator_bulk_data *supplies;
+	const struct st7703_panel_desc *desc;
+	bool prepared;
+};
+
+static inline struct st7703 *panel_to_st7703(struct drm_panel *panel)
+{
+	return container_of(panel, struct st7703, panel);
+}
+
+#define dsi_dcs_write_seq(dsi, cmd, seq...) do {			\
+		static const u8 d[] = { seq };				\
+		int ret;						\
+		ret = mipi_dsi_dcs_write(dsi, cmd, d, ARRAY_SIZE(d));	\
+		if (ret < 0)						\
+			return ret;					\
+	} while (0)
+
+static int st7703_init_sequence(struct st7703 *ctx)
+{
+	struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
+	struct device *dev = ctx->dev;
+	int ret;
+
+	/*
+	 * Init sequence was supplied by the panel vendor.
+	 */
+	dsi_dcs_write_seq(dsi, ST7703_CMD_SETEXTC,
+			  0xF1, 0x12, 0x83);
+	dsi_dcs_write_seq(dsi, ST7703_CMD_SETMIPI,
+			  0x33, 0x81, 0x05, 0xF9, 0x0E, 0x0E, 0x20, 0x00,
+			  0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x44, 0x25,
+			  0x00, 0x91, 0x0a, 0x00, 0x00, 0x02, 0x4F, 0x11,
+			  0x00, 0x00, 0x37);
+	dsi_dcs_write_seq(dsi, ST7703_CMD_SETPOWER_EXT,
+			  0x25, 0x22, 0x20, 0x03);
+	dsi_dcs_write_seq(dsi, ST7703_CMD_SETRGBIF,
+			  0x10, 0x10, 0x05, 0x05, 0x03, 0xFF, 0x00, 0x00,
+			  0x00, 0x00);
+	dsi_dcs_write_seq(dsi, ST7703_CMD_SETSCR,
+			  0x73, 0x73, 0x50, 0x50, 0x00, 0xC0, 0x08, 0x70,
+			  0x00);
+	dsi_dcs_write_seq(dsi, ST7703_CMD_SETVDC, 0x4E);
+	dsi_dcs_write_seq(dsi, ST7703_CMD_SETPANEL, 0x0B);
+	dsi_dcs_write_seq(dsi, ST7703_CMD_SETCYC, 0x80);
+	dsi_dcs_write_seq(dsi, ST7703_CMD_SETDISP, 0xF0, 0x12, 0xF0);
+	dsi_dcs_write_seq(dsi, ST7703_CMD_SETEQ,
+			  0x00, 0x00, 0x0B, 0x0B, 0x10, 0x10, 0x00, 0x00,
+			  0x00, 0x00, 0xFF, 0x00, 0xC0, 0x10);
+	dsi_dcs_write_seq(dsi, 0xC6, 0x01, 0x00, 0xFF, 0xFF, 0x00);
+	dsi_dcs_write_seq(dsi, ST7703_CMD_SETPOWER,
+			  0x74, 0x00, 0x32, 0x32, 0x77, 0xF1, 0xFF, 0xFF,
+			  0xCC, 0xCC, 0x77, 0x77);
+	dsi_dcs_write_seq(dsi, ST7703_CMD_SETBGP, 0x07, 0x07);
+	dsi_dcs_write_seq(dsi, ST7703_CMD_SETVCOM, 0x2C, 0x2C);
+	dsi_dcs_write_seq(dsi, 0xBF, 0x02, 0x11, 0x00);
+
+	dsi_dcs_write_seq(dsi, ST7703_CMD_SETGIP1,
+			  0x82, 0x10, 0x06, 0x05, 0xA2, 0x0A, 0xA5, 0x12,
+			  0x31, 0x23, 0x37, 0x83, 0x04, 0xBC, 0x27, 0x38,
+			  0x0C, 0x00, 0x03, 0x00, 0x00, 0x00, 0x0C, 0x00,
+			  0x03, 0x00, 0x00, 0x00, 0x75, 0x75, 0x31, 0x88,
+			  0x88, 0x88, 0x88, 0x88, 0x88, 0x13, 0x88, 0x64,
+			  0x64, 0x20, 0x88, 0x88, 0x88, 0x88, 0x88, 0x88,
+			  0x02, 0x88, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+			  0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00);
+	dsi_dcs_write_seq(dsi, ST7703_CMD_SETGIP2,
+			  0x02, 0x21, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+			  0x00, 0x00, 0x00, 0x00, 0x02, 0x46, 0x02, 0x88,
+			  0x88, 0x88, 0x88, 0x88, 0x88, 0x64, 0x88, 0x13,
+			  0x57, 0x13, 0x88, 0x88, 0x88, 0x88, 0x88, 0x88,
+			  0x75, 0x88, 0x23, 0x14, 0x00, 0x00, 0x02, 0x00,
+			  0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+			  0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x03, 0x0A,
+			  0xA5, 0x00, 0x00, 0x00, 0x00);
+	dsi_dcs_write_seq(dsi, ST7703_CMD_SETGAMMA,
+			  0x00, 0x09, 0x0D, 0x23, 0x27, 0x3C, 0x41, 0x35,
+			  0x07, 0x0D, 0x0E, 0x12, 0x13, 0x10, 0x12, 0x12,
+			  0x18, 0x00, 0x09, 0x0D, 0x23, 0x27, 0x3C, 0x41,
+			  0x35, 0x07, 0x0D, 0x0E, 0x12, 0x13, 0x10, 0x12,
+			  0x12, 0x18);
+	msleep(20);
+
+	ret = mipi_dsi_dcs_exit_sleep_mode(dsi);
+	if (ret < 0) {
+		DRM_DEV_ERROR(dev, "Failed to exit sleep mode\n");
+		return ret;
+	}
+	msleep(250);
+
+	ret = mipi_dsi_dcs_set_display_on(dsi);
+	if (ret)
+		return ret;
+	msleep(50);
+
+	DRM_DEV_DEBUG_DRIVER(dev, "Panel init sequence done\n");
+	return 0;
+}
+
+static int st7703_prepare(struct drm_panel *panel)
+{
+	struct st7703 *ctx = panel_to_st7703(panel);
+	int ret;
+
+	if (ctx->prepared)
+		return 0;
+
+	ret = regulator_bulk_enable(ctx->desc->num_supplies, ctx->supplies);
+	if (ret)
+		return ret;
+
+	DRM_DEV_DEBUG_DRIVER(ctx->dev, "Resetting the panel\n");
+	gpiod_set_value_cansleep(ctx->reset_gpio, 1);
+	usleep_range(20, 40);
+	gpiod_set_value_cansleep(ctx->reset_gpio, 0);
+	msleep(20);
+
+	ctx->prepared = true;
+
+	return 0;
+}
+
+static int st7703_enable(struct drm_panel *panel)
+{
+	struct st7703 *ctx = panel_to_st7703(panel);
+	int ret;
+
+	ret = st7703_init_sequence(ctx);
+	if (ret < 0) {
+		DRM_DEV_ERROR(ctx->dev, "Panel init sequence failed: %d\n",
+			      ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int st7703_disable(struct drm_panel *panel)
+{
+	struct st7703 *ctx = panel_to_st7703(panel);
+	struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
+
+	return mipi_dsi_dcs_set_display_off(dsi);
+}
+
+static int st7703_unprepare(struct drm_panel *panel)
+{
+	struct st7703 *ctx = panel_to_st7703(panel);
+
+	if (!ctx->prepared)
+		return 0;
+
+	gpiod_set_value_cansleep(ctx->reset_gpio, 1);
+	regulator_bulk_disable(ctx->desc->num_supplies, ctx->supplies);
+	ctx->prepared = false;
+
+	return 0;
+}
+
+static int st7703_get_modes(struct drm_panel *panel,
+			    struct drm_connector *connector)
+{
+	struct st7703 *ctx = panel_to_st7703(panel);
+	struct drm_display_mode *mode;
+
+	mode = drm_mode_duplicate(connector->dev, ctx->desc->mode);
+	if (!mode) {
+		DRM_DEV_ERROR(ctx->dev, "Failed to add mode\n");
+		return -ENOMEM;
+	}
+
+	drm_mode_set_name(mode);
+
+	mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;
+	connector->display_info.width_mm = mode->width_mm;
+	connector->display_info.height_mm = mode->height_mm;
+	drm_mode_probed_add(connector, mode);
+
+	return 1;
+}
+
+static const struct drm_panel_funcs st7703_drm_funcs = {
+	.prepare   = st7703_prepare,
+	.enable    = st7703_enable,
+	.disable   = st7703_disable,
+	.unprepare = st7703_unprepare,
+	.get_modes = st7703_get_modes,
+};
+
+static const struct drm_display_mode xbd599_mode = {
+	.hdisplay    = 720,
+	.hsync_start = 720 + 40,
+	.hsync_end   = 720 + 40 + 40,
+	.htotal	     = 720 + 40 + 40 + 40,
+	.vdisplay    = 1440,
+	.vsync_start = 1440 + 18,
+	.vsync_end   = 1440 + 18 + 10,
+	.vtotal	     = 1440 + 18 + 10 + 17,
+	.vrefresh    = 60,
+	.clock	     = 69000,
+	.flags	     = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC,
+
+	.width_mm    = 68,
+	.height_mm   = 136,
+	.type        = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED,
+};
+
+static const char * const xbd599_supply_names[] = {
+	"iovcc",
+	"vcc",
+};
+
+static const struct st7703_panel_desc xbd599_desc = {
+	.mode = &xbd599_mode,
+	.lanes = 4,
+	.flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_SYNC_PULSE,
+	.format = MIPI_DSI_FMT_RGB888,
+	.supply_names = xbd599_supply_names,
+	.num_supplies = ARRAY_SIZE(xbd599_supply_names),
+};
+
+static int st7703_probe(struct mipi_dsi_device *dsi)
+{
+	const struct st7703_panel_desc *desc;
+	struct device *dev = &dsi->dev;
+	struct st7703 *ctx;
+	int i, ret;
+
+	ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
+	if (!ctx)
+		return -ENOMEM;
+
+	ctx->dev = dev;
+	ctx->desc = desc = of_device_get_match_data(dev);
+
+	dsi->mode_flags = desc->flags;
+	dsi->format = desc->format;
+	dsi->lanes = desc->lanes;
+
+	ctx->supplies = devm_kcalloc(&dsi->dev, desc->num_supplies,
+					sizeof(*ctx->supplies),
+					GFP_KERNEL);
+	if (!ctx->supplies)
+		return -ENOMEM;
+
+	for (i = 0; i < desc->num_supplies; i++)
+		ctx->supplies[i].supply = desc->supply_names[i];
+
+	ret = devm_regulator_bulk_get(&dsi->dev, desc->num_supplies,
+				      ctx->supplies);
+	if (ret < 0)
+		return ret;
+
+	ctx->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
+	if (IS_ERR(ctx->reset_gpio)) {
+		DRM_DEV_ERROR(dev, "Can't get reset gpio\n");
+		return PTR_ERR(ctx->reset_gpio);
+	}
+
+	mipi_dsi_set_drvdata(dsi, ctx);
+
+	drm_panel_init(&ctx->panel, &dsi->dev, &st7703_drm_funcs,
+		       DRM_MODE_CONNECTOR_DSI);
+
+	ret = drm_panel_of_backlight(&ctx->panel);
+	if (ret)
+		return ret;
+
+	drm_panel_add(&ctx->panel);
+
+	ret = mipi_dsi_attach(dsi);
+	if (ret < 0) {
+		DRM_DEV_ERROR(dev, "mipi_dsi_attach failed. Is host ready?\n");
+		drm_panel_remove(&ctx->panel);
+		return ret;
+	}
+
+	return 0;
+}
+
+static void st7703_shutdown(struct mipi_dsi_device *dsi)
+{
+	struct st7703 *ctx = mipi_dsi_get_drvdata(dsi);
+	int ret;
+
+	ret = drm_panel_unprepare(&ctx->panel);
+	if (ret < 0)
+		DRM_DEV_ERROR(&dsi->dev, "Failed to unprepare panel: %d\n",
+			      ret);
+}
+
+static int st7703_remove(struct mipi_dsi_device *dsi)
+{
+	struct st7703 *ctx = mipi_dsi_get_drvdata(dsi);
+	int ret;
+
+	st7703_shutdown(dsi);
+
+	ret = mipi_dsi_detach(dsi);
+	if (ret < 0)
+		DRM_DEV_ERROR(&dsi->dev, "Failed to detach from DSI host: %d\n",
+			      ret);
+
+	drm_panel_remove(&ctx->panel);
+
+	return 0;
+}
+
+static const struct of_device_id st7703_of_match[] = {
+	{ .compatible = "xingbangda,xbd599", .data = &xbd599_desc },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, st7703_of_match);
+
+static struct mipi_dsi_driver st7703_driver = {
+	.probe	= st7703_probe,
+	.remove = st7703_remove,
+	.shutdown = st7703_shutdown,
+	.driver = {
+		.name = "st7703",
+		.of_match_table = st7703_of_match,
+	},
+};
+module_mipi_dsi_driver(st7703_driver);
+
+MODULE_AUTHOR("Icenowy Zheng <icenowy@aosc.io>");
+MODULE_DESCRIPTION("DRM driver for Sitronix ST7703 MIPI DSI panel");
+MODULE_LICENSE("GPL v2");
-- 
2.26.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 3/5] drm: panel: Add Xingbangda XBD599 panel (ST7703 controller)

[Linus Walleij]

Hi Ondrej,

I see you took over this driver submission from
Icenowy.

On Wed, May 13, 2020 at 11:24 PM Ondrej Jirman <megous@megous.com> wrote:

> From: Icenowy Zheng <icenowy@aosc.io>
>
> Xingbangda XBD599 is a 5.99" 720x1440 MIPI-DSI IPS LCD panel made by
> Xingbangda, which is used on PinePhone final assembled phones.
>
> It is based on Sitronix ST7703 LCD controller.
>
> Add support for it.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> Signed-off-by: Ondrej Jirman <megous@megous.com>

(...)
>  create mode 100644 drivers/gpu/drm/panel/panel-sitronix-st7703.c

Nice!

> +       /*
> +        * Init sequence was supplied by the panel vendor.
> +        */
> +       dsi_dcs_write_seq(dsi, ST7703_CMD_SETEXTC,
> +                         0xF1, 0x12, 0x83);
> +       dsi_dcs_write_seq(dsi, ST7703_CMD_SETMIPI,
> +                         0x33, 0x81, 0x05, 0xF9, 0x0E, 0x0E, 0x20, 0x00,
> +                         0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x44, 0x25,
> +                         0x00, 0x91, 0x0a, 0x00, 0x00, 0x02, 0x4F, 0x11,
> +                         0x00, 0x00, 0x37);
> +       dsi_dcs_write_seq(dsi, ST7703_CMD_SETPOWER_EXT,
> +                         0x25, 0x22, 0x20, 0x03);
> +       dsi_dcs_write_seq(dsi, ST7703_CMD_SETRGBIF,
> +                         0x10, 0x10, 0x05, 0x05, 0x03, 0xFF, 0x00, 0x00,
> +                         0x00, 0x00);
> +       dsi_dcs_write_seq(dsi, ST7703_CMD_SETSCR,
> +                         0x73, 0x73, 0x50, 0x50, 0x00, 0xC0, 0x08, 0x70,
> +                         0x00);
> +       dsi_dcs_write_seq(dsi, ST7703_CMD_SETVDC, 0x4E);
> +       dsi_dcs_write_seq(dsi, ST7703_CMD_SETPANEL, 0x0B);
> +       dsi_dcs_write_seq(dsi, ST7703_CMD_SETCYC, 0x80);
> +       dsi_dcs_write_seq(dsi, ST7703_CMD_SETDISP, 0xF0, 0x12, 0xF0);
> +       dsi_dcs_write_seq(dsi, ST7703_CMD_SETEQ,
> +                         0x00, 0x00, 0x0B, 0x0B, 0x10, 0x10, 0x00, 0x00,
> +                         0x00, 0x00, 0xFF, 0x00, 0xC0, 0x10);
> +       dsi_dcs_write_seq(dsi, 0xC6, 0x01, 0x00, 0xFF, 0xFF, 0x00);
> +       dsi_dcs_write_seq(dsi, ST7703_CMD_SETPOWER,
> +                         0x74, 0x00, 0x32, 0x32, 0x77, 0xF1, 0xFF, 0xFF,
> +                         0xCC, 0xCC, 0x77, 0x77);
> +       dsi_dcs_write_seq(dsi, ST7703_CMD_SETBGP, 0x07, 0x07);
> +       dsi_dcs_write_seq(dsi, ST7703_CMD_SETVCOM, 0x2C, 0x2C);
> +       dsi_dcs_write_seq(dsi, 0xBF, 0x02, 0x11, 0x00);
> +
> +       dsi_dcs_write_seq(dsi, ST7703_CMD_SETGIP1,
> +                         0x82, 0x10, 0x06, 0x05, 0xA2, 0x0A, 0xA5, 0x12,
> +                         0x31, 0x23, 0x37, 0x83, 0x04, 0xBC, 0x27, 0x38,
> +                         0x0C, 0x00, 0x03, 0x00, 0x00, 0x00, 0x0C, 0x00,
> +                         0x03, 0x00, 0x00, 0x00, 0x75, 0x75, 0x31, 0x88,
> +                         0x88, 0x88, 0x88, 0x88, 0x88, 0x13, 0x88, 0x64,
> +                         0x64, 0x20, 0x88, 0x88, 0x88, 0x88, 0x88, 0x88,
> +                         0x02, 0x88, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
> +                         0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00);
> +       dsi_dcs_write_seq(dsi, ST7703_CMD_SETGIP2,
> +                         0x02, 0x21, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
> +                         0x00, 0x00, 0x00, 0x00, 0x02, 0x46, 0x02, 0x88,
> +                         0x88, 0x88, 0x88, 0x88, 0x88, 0x64, 0x88, 0x13,
> +                         0x57, 0x13, 0x88, 0x88, 0x88, 0x88, 0x88, 0x88,
> +                         0x75, 0x88, 0x23, 0x14, 0x00, 0x00, 0x02, 0x00,
> +                         0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
> +                         0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x03, 0x0A,
> +                         0xA5, 0x00, 0x00, 0x00, 0x00);
> +       dsi_dcs_write_seq(dsi, ST7703_CMD_SETGAMMA,
> +                         0x00, 0x09, 0x0D, 0x23, 0x27, 0x3C, 0x41, 0x35,
> +                         0x07, 0x0D, 0x0E, 0x12, 0x13, 0x10, 0x12, 0x12,
> +                         0x18, 0x00, 0x09, 0x0D, 0x23, 0x27, 0x3C, 0x41,
> +                         0x35, 0x07, 0x0D, 0x0E, 0x12, 0x13, 0x10, 0x12,
> +                         0x12, 0x18);
> +       msleep(20);

This stuff is really hard or impossible to understand without the
datasheet.

In my previous review I wrote:

It appears that the Himax HX8363 is using the same display controller
if you look at the datasheet:
http://www.datasheet-pdf.com/PDF/HX8369-A-Datasheet-Himax-729024
There you find an explanation to some of the commands.

That means, try to get rid of as much of the magic bytes as you can
and use proper #defines. I know it takes some work but the result
is so much more useful and readable.

Further I wrote:

You should definately insert code to read the MTP bytes:
0xDA manufacturer
0xDB driver version
0xDC LCD module/driver
And print these, se e.g. my newly added NT35510 driver or
the Sony ACX424AKP driver.

So please do that.

Yours,
Linus Walleij

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [linux-sunxi] Re: [PATCH v3 3/5] drm: panel: Add Xingbangda XBD599 panel (ST7703 controller)

[Ondřej Jirman]

Hello Linus,

On Tue, May 26, 2020 at 01:32:25PM +0200, Linus Walleij wrote:
> Hi Ondrej,
> 

[...]

> > +       dsi_dcs_write_seq(dsi, ST7703_CMD_SETGIP1,
> > +                         0x82, 0x10, 0x06, 0x05, 0xA2, 0x0A, 0xA5, 0x12,
> > +                         0x31, 0x23, 0x37, 0x83, 0x04, 0xBC, 0x27, 0x38,
> > +                         0x0C, 0x00, 0x03, 0x00, 0x00, 0x00, 0x0C, 0x00,
> > +                         0x03, 0x00, 0x00, 0x00, 0x75, 0x75, 0x31, 0x88,
> > +                         0x88, 0x88, 0x88, 0x88, 0x88, 0x13, 0x88, 0x64,
> > +                         0x64, 0x20, 0x88, 0x88, 0x88, 0x88, 0x88, 0x88,
> > +                         0x02, 0x88, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
> > +                         0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00);
> > +       dsi_dcs_write_seq(dsi, ST7703_CMD_SETGIP2,
> > +                         0x02, 0x21, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
> > +                         0x00, 0x00, 0x00, 0x00, 0x02, 0x46, 0x02, 0x88,
> > +                         0x88, 0x88, 0x88, 0x88, 0x88, 0x64, 0x88, 0x13,
> > +                         0x57, 0x13, 0x88, 0x88, 0x88, 0x88, 0x88, 0x88,
> > +                         0x75, 0x88, 0x23, 0x14, 0x00, 0x00, 0x02, 0x00,
> > +                         0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
> > +                         0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x03, 0x0A,
> > +                         0xA5, 0x00, 0x00, 0x00, 0x00);
> > +       dsi_dcs_write_seq(dsi, ST7703_CMD_SETGAMMA,
> > +                         0x00, 0x09, 0x0D, 0x23, 0x27, 0x3C, 0x41, 0x35,
> > +                         0x07, 0x0D, 0x0E, 0x12, 0x13, 0x10, 0x12, 0x12,
> > +                         0x18, 0x00, 0x09, 0x0D, 0x23, 0x27, 0x3C, 0x41,
> > +                         0x35, 0x07, 0x0D, 0x0E, 0x12, 0x13, 0x10, 0x12,
> > +                         0x12, 0x18);
> > +       msleep(20);
> 
> This stuff is really hard or impossible to understand without the
> datasheet.
> 
> In my previous review I wrote:
> 
> It appears that the Himax HX8363 is using the same display controller
> if you look at the datasheet:
> http://www.datasheet-pdf.com/PDF/HX8369-A-Datasheet-Himax-729024
> There you find an explanation to some of the commands.

It is st7703, and we have a fairly complete datasheet available
publicly. I posted links in the cover letter.

> That means, try to get rid of as much of the magic bytes as you can
> and use proper #defines. I know it takes some work but the result
> is so much more useful and readable.

I've added some descriptions from the datasheet as comments next
to the values in v4.

Thank you and regards,
	o.

> Further I wrote:
> 
> You should definately insert code to read the MTP bytes:
> 0xDA manufacturer
> 0xDB driver version
> 0xDC LCD module/driver
> And print these, se e.g. my newly added NT35510 driver or
> the Sony ACX424AKP driver.
> 
> So please do that.
> 
> Yours,
> Linus Walleij
> 
> -- 
> You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
> To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe@googlegroups.com.
> To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/CACRpkdZpiQ7E_v-Gfk6vFcUEiMazvixYaL0ksKeP%3DTq3O6Fh%3DQ%40mail.gmail.com.

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 3/5] drm: panel: Add Xingbangda XBD599 panel (ST7703 controller)

[Samuel Holland]

On 5/13/20 4:24 PM, Ondrej Jirman wrote:
> From: Icenowy Zheng <icenowy@aosc.io>
> 
> Xingbangda XBD599 is a 5.99" 720x1440 MIPI-DSI IPS LCD panel made by
> Xingbangda, which is used on PinePhone final assembled phones.
> 
> It is based on Sitronix ST7703 LCD controller.
> 
> Add support for it.
> 
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> Signed-off-by: Ondrej Jirman <megous@megous.com>
> ---
>  drivers/gpu/drm/panel/Kconfig                 |  10 +
>  drivers/gpu/drm/panel/Makefile                |   1 +
>  drivers/gpu/drm/panel/panel-sitronix-st7703.c | 386 ++++++++++++++++++
>  3 files changed, 397 insertions(+)
>  create mode 100644 drivers/gpu/drm/panel/panel-sitronix-st7703.c
> 
> diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
> index 39055c1f0e2f..b7bc157b0612 100644
> --- a/drivers/gpu/drm/panel/Kconfig
> +++ b/drivers/gpu/drm/panel/Kconfig
> @@ -395,6 +395,16 @@ config DRM_PANEL_SITRONIX_ST7701
>  	  ST7701 controller for 480X864 LCD panels with MIPI/RGB/SPI
>  	  system interfaces.
>  
> +config DRM_PANEL_SITRONIX_ST7703
> +	tristate "Sitronix ST7703 panel driver"
> +	depends on OF
> +	depends on DRM_MIPI_DSI
> +	depends on BACKLIGHT_CLASS_DEVICE
> +	help
> +	  Say Y here if you want to enable support for the Sitronix
> +	  ST7703 controller for 720X1440 LCD panels with MIPI/RGB/SPI
> +	  system interfaces.
> +
>  config DRM_PANEL_SITRONIX_ST7789V
>  	tristate "Sitronix ST7789V panel"
>  	depends on OF && SPI
> diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile
> index de74f282c433..47f4789a8685 100644
> --- a/drivers/gpu/drm/panel/Makefile
> +++ b/drivers/gpu/drm/panel/Makefile
> @@ -41,6 +41,7 @@ obj-$(CONFIG_DRM_PANEL_SHARP_LQ101R1SX01) += panel-sharp-lq101r1sx01.o
>  obj-$(CONFIG_DRM_PANEL_SHARP_LS037V7DW01) += panel-sharp-ls037v7dw01.o
>  obj-$(CONFIG_DRM_PANEL_SHARP_LS043T1LE01) += panel-sharp-ls043t1le01.o
>  obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7701) += panel-sitronix-st7701.o
> +obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7703) += panel-sitronix-st7703.o
>  obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7789V) += panel-sitronix-st7789v.o
>  obj-$(CONFIG_DRM_PANEL_SONY_ACX424AKP) += panel-sony-acx424akp.o
>  obj-$(CONFIG_DRM_PANEL_SONY_ACX565AKM) += panel-sony-acx565akm.o
> diff --git a/drivers/gpu/drm/panel/panel-sitronix-st7703.c b/drivers/gpu/drm/panel/panel-sitronix-st7703.c
> new file mode 100644
> index 000000000000..092dd73c86d0
> --- /dev/null
> +++ b/drivers/gpu/drm/panel/panel-sitronix-st7703.c
> @@ -0,0 +1,386 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * DRM driver for Sitronix ST7703 MIPI DSI panel
> + *
> + * Copyright (C) 2020 Ondrej Jirman <megous@megous.com>
> + * Copyright (C) 2019-2020 Icenowy Zheng <icenowy@aosc.io>
> + *
> + * Based on panel-rocktech-jh057n00900.c, which is:
> + *   Copyright (C) Purism SPC 2019
> + */
> +
> +#include <linux/delay.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/mod_devicetable.h>
> +#include <linux/module.h>
> +#include <linux/of_device.h>
> +#include <linux/regulator/consumer.h>
> +
> +#include <drm/drm_mipi_dsi.h>
> +#include <drm/drm_modes.h>
> +#include <drm/drm_panel.h>
> +#include <drm/drm_print.h>
> +
> +/* Manufacturer specific Commands send via DSI */
> +#define ST7703_CMD_ALL_PIXEL_OFF 0x22
> +#define ST7703_CMD_ALL_PIXEL_ON	 0x23
> +#define ST7703_CMD_SETDISP	 0xB2
> +#define ST7703_CMD_SETRGBIF	 0xB3
> +#define ST7703_CMD_SETCYC	 0xB4
> +#define ST7703_CMD_SETBGP	 0xB5
> +#define ST7703_CMD_SETVCOM	 0xB6
> +#define ST7703_CMD_SETOTP	 0xB7
> +#define ST7703_CMD_SETPOWER_EXT	 0xB8
> +#define ST7703_CMD_SETEXTC	 0xB9
> +#define ST7703_CMD_SETMIPI	 0xBA
> +#define ST7703_CMD_SETVDC	 0xBC
> +#define ST7703_CMD_SETSCR	 0xC0
> +#define ST7703_CMD_SETPOWER	 0xC1
> +#define ST7703_CMD_UNK_C6	 0xC6
> +#define ST7703_CMD_SETPANEL	 0xCC
> +#define ST7703_CMD_SETGAMMA	 0xE0
> +#define ST7703_CMD_SETEQ	 0xE3
> +#define ST7703_CMD_SETGIP1	 0xE9
> +#define ST7703_CMD_SETGIP2	 0xEA
> +
> +struct st7703_panel_desc {
> +	const struct drm_display_mode *mode;
> +	unsigned int lanes;
> +	unsigned long flags;
> +	enum mipi_dsi_pixel_format format;
> +	const char *const *supply_names;
> +	unsigned int num_supplies;
> +};
> +
> +struct st7703 {
> +	struct device *dev;
> +	struct drm_panel panel;
> +	struct gpio_desc *reset_gpio;
> +	struct regulator_bulk_data *supplies;
> +	const struct st7703_panel_desc *desc;
> +	bool prepared;
> +};
> +
> +static inline struct st7703 *panel_to_st7703(struct drm_panel *panel)
> +{
> +	return container_of(panel, struct st7703, panel);
> +}
> +
> +#define dsi_dcs_write_seq(dsi, cmd, seq...) do {			\
> +		static const u8 d[] = { seq };				\
> +		int ret;						\
> +		ret = mipi_dsi_dcs_write(dsi, cmd, d, ARRAY_SIZE(d));	\
> +		if (ret < 0)						\
> +			return ret;					\
> +	} while (0)
> +
> +static int st7703_init_sequence(struct st7703 *ctx)
> +{
> +	struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
> +	struct device *dev = ctx->dev;
> +	int ret;
> +
> +	/*
> +	 * Init sequence was supplied by the panel vendor.
> +	 */
> +	dsi_dcs_write_seq(dsi, ST7703_CMD_SETEXTC,
> +			  0xF1, 0x12, 0x83);
> +	dsi_dcs_write_seq(dsi, ST7703_CMD_SETMIPI,
> +			  0x33, 0x81, 0x05, 0xF9, 0x0E, 0x0E, 0x20, 0x00,
> +			  0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x44, 0x25,
> +			  0x00, 0x91, 0x0a, 0x00, 0x00, 0x02, 0x4F, 0x11,
> +			  0x00, 0x00, 0x37);
> +	dsi_dcs_write_seq(dsi, ST7703_CMD_SETPOWER_EXT,
> +			  0x25, 0x22, 0x20, 0x03);
> +	dsi_dcs_write_seq(dsi, ST7703_CMD_SETRGBIF,
> +			  0x10, 0x10, 0x05, 0x05, 0x03, 0xFF, 0x00, 0x00,
> +			  0x00, 0x00);
> +	dsi_dcs_write_seq(dsi, ST7703_CMD_SETSCR,
> +			  0x73, 0x73, 0x50, 0x50, 0x00, 0xC0, 0x08, 0x70,
> +			  0x00);
> +	dsi_dcs_write_seq(dsi, ST7703_CMD_SETVDC, 0x4E);
> +	dsi_dcs_write_seq(dsi, ST7703_CMD_SETPANEL, 0x0B);
> +	dsi_dcs_write_seq(dsi, ST7703_CMD_SETCYC, 0x80);
> +	dsi_dcs_write_seq(dsi, ST7703_CMD_SETDISP, 0xF0, 0x12, 0xF0);
> +	dsi_dcs_write_seq(dsi, ST7703_CMD_SETEQ,
> +			  0x00, 0x00, 0x0B, 0x0B, 0x10, 0x10, 0x00, 0x00,
> +			  0x00, 0x00, 0xFF, 0x00, 0xC0, 0x10);
> +	dsi_dcs_write_seq(dsi, 0xC6, 0x01, 0x00, 0xFF, 0xFF, 0x00);
> +	dsi_dcs_write_seq(dsi, ST7703_CMD_SETPOWER,
> +			  0x74, 0x00, 0x32, 0x32, 0x77, 0xF1, 0xFF, 0xFF,
> +			  0xCC, 0xCC, 0x77, 0x77);
> +	dsi_dcs_write_seq(dsi, ST7703_CMD_SETBGP, 0x07, 0x07);
> +	dsi_dcs_write_seq(dsi, ST7703_CMD_SETVCOM, 0x2C, 0x2C);
> +	dsi_dcs_write_seq(dsi, 0xBF, 0x02, 0x11, 0x00);
> +
> +	dsi_dcs_write_seq(dsi, ST7703_CMD_SETGIP1,
> +			  0x82, 0x10, 0x06, 0x05, 0xA2, 0x0A, 0xA5, 0x12,
> +			  0x31, 0x23, 0x37, 0x83, 0x04, 0xBC, 0x27, 0x38,
> +			  0x0C, 0x00, 0x03, 0x00, 0x00, 0x00, 0x0C, 0x00,
> +			  0x03, 0x00, 0x00, 0x00, 0x75, 0x75, 0x31, 0x88,
> +			  0x88, 0x88, 0x88, 0x88, 0x88, 0x13, 0x88, 0x64,
> +			  0x64, 0x20, 0x88, 0x88, 0x88, 0x88, 0x88, 0x88,
> +			  0x02, 0x88, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
> +			  0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00);
> +	dsi_dcs_write_seq(dsi, ST7703_CMD_SETGIP2,
> +			  0x02, 0x21, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
> +			  0x00, 0x00, 0x00, 0x00, 0x02, 0x46, 0x02, 0x88,
> +			  0x88, 0x88, 0x88, 0x88, 0x88, 0x64, 0x88, 0x13,
> +			  0x57, 0x13, 0x88, 0x88, 0x88, 0x88, 0x88, 0x88,
> +			  0x75, 0x88, 0x23, 0x14, 0x00, 0x00, 0x02, 0x00,
> +			  0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
> +			  0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x03, 0x0A,
> +			  0xA5, 0x00, 0x00, 0x00, 0x00);
> +	dsi_dcs_write_seq(dsi, ST7703_CMD_SETGAMMA,
> +			  0x00, 0x09, 0x0D, 0x23, 0x27, 0x3C, 0x41, 0x35,
> +			  0x07, 0x0D, 0x0E, 0x12, 0x13, 0x10, 0x12, 0x12,
> +			  0x18, 0x00, 0x09, 0x0D, 0x23, 0x27, 0x3C, 0x41,
> +			  0x35, 0x07, 0x0D, 0x0E, 0x12, 0x13, 0x10, 0x12,
> +			  0x12, 0x18);
> +	msleep(20);
> +
> +	ret = mipi_dsi_dcs_exit_sleep_mode(dsi);
> +	if (ret < 0) {
> +		DRM_DEV_ERROR(dev, "Failed to exit sleep mode\n");
> +		return ret;
> +	}
> +	msleep(250);
> +
> +	ret = mipi_dsi_dcs_set_display_on(dsi);

Since you have the complementary call to mipi_dsi_dcs_set_display_off in
st7703_disable, I would suggest calling this from st7703_enable, after the call
to st7703_init_sequence. [but see below about moving all of this to prepare.]

> +	if (ret)
> +		return ret;
> +	msleep(50);

This is the last step of the init sequence. According to table 8-1 of the
manual, T10 needs no delay. What is this delay for?

> +
> +	DRM_DEV_DEBUG_DRIVER(dev, "Panel init sequence done\n");
> +	return 0;
> +}
> +
> +static int st7703_prepare(struct drm_panel *panel)
> +{
> +	struct st7703 *ctx = panel_to_st7703(panel);
> +	int ret;
> +
> +	if (ctx->prepared)
> +		return 0;
> +
> +	ret = regulator_bulk_enable(ctx->desc->num_supplies, ctx->supplies);
> +	if (ret)
> +		return ret;
> +
> +	DRM_DEV_DEBUG_DRIVER(ctx->dev, "Resetting the panel\n");
> +	gpiod_set_value_cansleep(ctx->reset_gpio, 1);
> +	usleep_range(20, 40);
> +	gpiod_set_value_cansleep(ctx->reset_gpio, 0);
> +	msleep(20);
> +
> +	ctx->prepared = true;
> +
> +	return 0;
> +}
> +
> +static int st7703_enable(struct drm_panel *panel)
> +{
> +	struct st7703 *ctx = panel_to_st7703(panel);
> +	int ret;
> +
> +	ret = st7703_init_sequence(ctx);

v1 had this function called from prepare, not enable. From reading the comments
in drm_panel.h, that seems to be the right place for it.

> +	if (ret < 0) {
> +		DRM_DEV_ERROR(ctx->dev, "Panel init sequence failed: %d\n",
> +			      ret);
> +		return ret;
> +	}
> +
> +	return 0;
> +}
> +
> +static int st7703_disable(struct drm_panel *panel)
> +{
> +	struct st7703 *ctx = panel_to_st7703(panel);
> +	struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
> +
> +	return mipi_dsi_dcs_set_display_off(dsi);

The datasheet suggests in "5.6 Power on/off Sequence" that there also needs to
be a call to mipi_dsi_dcs_enter_sleep_mode() here.

> +}
> +
> +static int st7703_unprepare(struct drm_panel *panel)
> +{
> +	struct st7703 *ctx = panel_to_st7703(panel);
> +
> +	if (!ctx->prepared)
> +		return 0;
> +
> +	gpiod_set_value_cansleep(ctx->reset_gpio, 1);
> +	regulator_bulk_disable(ctx->desc->num_supplies, ctx->supplies);
> +	ctx->prepared = false;
> +
> +	return 0;
> +}
> +
> +static int st7703_get_modes(struct drm_panel *panel,
> +			    struct drm_connector *connector)
> +{
> +	struct st7703 *ctx = panel_to_st7703(panel);
> +	struct drm_display_mode *mode;
> +
> +	mode = drm_mode_duplicate(connector->dev, ctx->desc->mode);
> +	if (!mode) {
> +		DRM_DEV_ERROR(ctx->dev, "Failed to add mode\n");
> +		return -ENOMEM;
> +	}
> +
> +	drm_mode_set_name(mode);
> +
> +	mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;

This line...

> +	connector->display_info.width_mm = mode->width_mm;
> +	connector->display_info.height_mm = mode->height_mm;
> +	drm_mode_probed_add(connector, mode);
> +
> +	return 1;
> +}
> +
> +static const struct drm_panel_funcs st7703_drm_funcs = {
> +	.prepare   = st7703_prepare,
> +	.enable    = st7703_enable,
> +	.disable   = st7703_disable,
> +	.unprepare = st7703_unprepare,
> +	.get_modes = st7703_get_modes,
> +};
> +
> +static const struct drm_display_mode xbd599_mode = {
> +	.hdisplay    = 720,
> +	.hsync_start = 720 + 40,
> +	.hsync_end   = 720 + 40 + 40,
> +	.htotal	     = 720 + 40 + 40 + 40,
> +	.vdisplay    = 1440,
> +	.vsync_start = 1440 + 18,
> +	.vsync_end   = 1440 + 18 + 10,
> +	.vtotal	     = 1440 + 18 + 10 + 17,
> +	.vrefresh    = 60,
> +	.clock	     = 69000,
> +	.flags	     = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC,
> +
> +	.width_mm    = 68,
> +	.height_mm   = 136,
> +	.type        = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED,

...duplicates this line. I'm not sure which is the better place to put it; panel
drivers seem evenly split. But it doesn't need to be in both places.

Cheers,
Samuel

> +};
> +
> +static const char * const xbd599_supply_names[] = {
> +	"iovcc",
> +	"vcc",
> +};
> +
> +static const struct st7703_panel_desc xbd599_desc = {
> +	.mode = &xbd599_mode,
> +	.lanes = 4,
> +	.flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_SYNC_PULSE,
> +	.format = MIPI_DSI_FMT_RGB888,
> +	.supply_names = xbd599_supply_names,
> +	.num_supplies = ARRAY_SIZE(xbd599_supply_names),
> +};
> +
> +static int st7703_probe(struct mipi_dsi_device *dsi)
> +{
> +	const struct st7703_panel_desc *desc;
> +	struct device *dev = &dsi->dev;
> +	struct st7703 *ctx;
> +	int i, ret;
> +
> +	ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
> +	if (!ctx)
> +		return -ENOMEM;
> +
> +	ctx->dev = dev;
> +	ctx->desc = desc = of_device_get_match_data(dev);
> +
> +	dsi->mode_flags = desc->flags;
> +	dsi->format = desc->format;
> +	dsi->lanes = desc->lanes;
> +
> +	ctx->supplies = devm_kcalloc(&dsi->dev, desc->num_supplies,
> +					sizeof(*ctx->supplies),
> +					GFP_KERNEL);
> +	if (!ctx->supplies)
> +		return -ENOMEM;
> +
> +	for (i = 0; i < desc->num_supplies; i++)
> +		ctx->supplies[i].supply = desc->supply_names[i];
> +
> +	ret = devm_regulator_bulk_get(&dsi->dev, desc->num_supplies,
> +				      ctx->supplies);
> +	if (ret < 0)
> +		return ret;
> +
> +	ctx->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
> +	if (IS_ERR(ctx->reset_gpio)) {
> +		DRM_DEV_ERROR(dev, "Can't get reset gpio\n");
> +		return PTR_ERR(ctx->reset_gpio);
> +	}
> +
> +	mipi_dsi_set_drvdata(dsi, ctx);
> +
> +	drm_panel_init(&ctx->panel, &dsi->dev, &st7703_drm_funcs,
> +		       DRM_MODE_CONNECTOR_DSI);
> +
> +	ret = drm_panel_of_backlight(&ctx->panel);
> +	if (ret)
> +		return ret;
> +
> +	drm_panel_add(&ctx->panel);
> +
> +	ret = mipi_dsi_attach(dsi);
> +	if (ret < 0) {
> +		DRM_DEV_ERROR(dev, "mipi_dsi_attach failed. Is host ready?\n");
> +		drm_panel_remove(&ctx->panel);
> +		return ret;
> +	}
> +
> +	return 0;
> +}
> +
> +static void st7703_shutdown(struct mipi_dsi_device *dsi)
> +{
> +	struct st7703 *ctx = mipi_dsi_get_drvdata(dsi);
> +	int ret;
> +
> +	ret = drm_panel_unprepare(&ctx->panel);
> +	if (ret < 0)
> +		DRM_DEV_ERROR(&dsi->dev, "Failed to unprepare panel: %d\n",
> +			      ret);
> +}
> +
> +static int st7703_remove(struct mipi_dsi_device *dsi)
> +{
> +	struct st7703 *ctx = mipi_dsi_get_drvdata(dsi);
> +	int ret;
> +
> +	st7703_shutdown(dsi);
> +
> +	ret = mipi_dsi_detach(dsi);
> +	if (ret < 0)
> +		DRM_DEV_ERROR(&dsi->dev, "Failed to detach from DSI host: %d\n",
> +			      ret);
> +
> +	drm_panel_remove(&ctx->panel);
> +
> +	return 0;
> +}
> +
> +static const struct of_device_id st7703_of_match[] = {
> +	{ .compatible = "xingbangda,xbd599", .data = &xbd599_desc },
> +	{ /* sentinel */ }
> +};
> +MODULE_DEVICE_TABLE(of, st7703_of_match);
> +
> +static struct mipi_dsi_driver st7703_driver = {
> +	.probe	= st7703_probe,
> +	.remove = st7703_remove,
> +	.shutdown = st7703_shutdown,
> +	.driver = {
> +		.name = "st7703",
> +		.of_match_table = st7703_of_match,
> +	},
> +};
> +module_mipi_dsi_driver(st7703_driver);
> +
> +MODULE_AUTHOR("Icenowy Zheng <icenowy@aosc.io>");
> +MODULE_DESCRIPTION("DRM driver for Sitronix ST7703 MIPI DSI panel");
> +MODULE_LICENSE("GPL v2");
> 


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 4/5] arm64: dts: sun50i-a64-pinephone: Enable LCD support on PinePhone

[Ondrej Jirman]

From: Icenowy Zheng <icenowy@aosc.io>

PinePhone uses PWM backlight and a XBD599 LCD panel over DSI for
display.

Backlight levels curve was optimized by Martijn Braam using a
lux meter.

Add its device nodes.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Martijn Braam <martijn@brixit.nl>
Signed-off-by: Ondrej Jirman <megous@megous.com>
---
 .../allwinner/sun50i-a64-pinephone-1.1.dts    | 19 ++++++++++
 .../dts/allwinner/sun50i-a64-pinephone.dtsi   | 35 +++++++++++++++++++
 2 files changed, 54 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts
index 06a775c41664..3e99a87e9ce5 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts
@@ -9,3 +9,22 @@ / {
 	model = "Pine64 PinePhone Braveheart (1.1)";
 	compatible = "pine64,pinephone-1.1", "allwinner,sun50i-a64";
 };
+
+&backlight {
+	power-supply = <&reg_ldo_io0>;
+	/*
+	 * PWM backlight circuit on this PinePhone revision was changed since
+	 * 1.0, and the lowest PWM duty cycle that doesn't lead to backlight
+	 * being off is around 20%. Duty cycle for the lowest brightness level
+	 * also varries quite a bit between individual boards, so the lowest
+	 * value here was chosen as a safe default.
+	 */
+	brightness-levels = <
+		774  793  814  842
+		882  935  1003 1088
+		1192 1316 1462 1633
+		1830 2054 2309 2596
+		2916 3271 3664 4096>;
+	num-interpolated-steps = <50>;
+	default-brightness-level = <400>;
+};
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi
index cefda145c3c9..e60b57f8ac14 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi
@@ -16,6 +16,13 @@ aliases {
 		serial0 = &uart0;
 	};
 
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&r_pwm 0 50000 PWM_POLARITY_INVERTED>;
+		enable-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* PH10 */
+		/* Backlight configuration differs per PinePhone revision. */
+	};
+
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
@@ -84,6 +91,30 @@ &dai {
 	status = "okay";
 };
 
+&de {
+	status = "okay";
+};
+
+&dphy {
+	status = "okay";
+};
+
+&dsi {
+	vcc-dsi-supply = <&reg_dldo1>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	panel@0 {
+		compatible = "xingbangda,xbd599", "sitronix,st7703";
+		reg = <0>;
+		reset-gpios = <&pio 3 23 GPIO_ACTIVE_LOW>; /* PD23 */
+		iovcc-supply = <&reg_dldo2>;
+		vcc-supply = <&reg_ldo_io0>;
+		backlight = <&backlight>;
+	};
+};
+
 &ehci0 {
 	status = "okay";
 };
@@ -188,6 +219,10 @@ &r_pio {
 	 */
 };
 
+&r_pwm {
+	status = "okay";
+};
+
 &r_rsb {
 	status = "okay";
 
-- 
2.26.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 4/5] arm64: dts: sun50i-a64-pinephone: Enable LCD support on PinePhone

[Pavel Machek]

[-- Attachment #1.1: Type: text/plain, Size: 1265 bytes --]

Hi!

> PinePhone uses PWM backlight and a XBD599 LCD panel over DSI for
> display.
> 
> Backlight levels curve was optimized by Martijn Braam using a
> lux meter.

If it was possible to preserve lux values for individual settings in
the comment somewhere... that would be nice :-).

One day, it would be nice to have brightness settings in lux, so I
could easily set matching levels on multiple devices, for example...

Best regards,

								Pavel

> +
> +&backlight {
> +	power-supply = <&reg_ldo_io0>;
> +	/*
> +	 * PWM backlight circuit on this PinePhone revision was changed since
> +	 * 1.0, and the lowest PWM duty cycle that doesn't lead to backlight
> +	 * being off is around 20%. Duty cycle for the lowest brightness level
> +	 * also varries quite a bit between individual boards, so the lowest
> +	 * value here was chosen as a safe default.
> +	 */
> +	brightness-levels = <
> +		774  793  814  842
> +		882  935  1003 1088
> +		1192 1316 1462 1633
> +		1830 2054 2309 2596
> +		2916 3271 3664 4096>;
> +	num-interpolated-steps = <50>;
> +	default-brightness-level = <400>;

-- 
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html

[-- Attachment #1.2: Digital signature --]
[-- Type: application/pgp-signature, Size: 181 bytes --]

[-- Attachment #2: Type: text/plain, Size: 176 bytes --]

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 5/5] arm64: dts: sun50i-a64-pinephone: Add touchscreen support

[Ondrej Jirman]

Pinephone has a Goodix GT917S capacitive touchscreen controller on
I2C0 bus. Add support for it.

Signed-off-by: Ondrej Jirman <megous@megous.com>
---
 .../dts/allwinner/sun50i-a64-pinephone.dtsi   | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi
index e60b57f8ac14..6b2ff431cddb 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi
@@ -123,6 +123,25 @@ &ehci1 {
 	status = "okay";
 };
 
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	status = "okay";
+
+	touchscreen@5d {
+		compatible = "goodix,gt917s", "goodix,gt911";
+		reg = <0x5d>;
+		interrupt-parent = <&pio>;
+		interrupts = <7 4 IRQ_TYPE_LEVEL_HIGH>; /* PH4 */
+		irq-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+		reset-gpios = <&pio 7 11 GPIO_ACTIVE_HIGH>; /* PH11 */
+		AVDD28-supply = <&reg_ldo_io0>;
+		VDDIO-supply = <&reg_ldo_io0>;
+		touchscreen-size-x = <720>;
+		touchscreen-size-y = <1440>;
+	};
+};
+
 &i2c1 {
 	status = "okay";
 
-- 
2.26.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel