* [PATCH v3 00/16] Allwinner A100 Initial support
@ 2020-07-08 7:19 Frank Lee
2020-07-08 7:19 ` [PATCH v3 01/16] dt-bindings: clk: sunxi-ccu: add compatible string for A100 CCU and R-CCU Frank Lee
` (10 more replies)
0 siblings, 11 replies; 22+ messages in thread
From: Frank Lee @ 2020-07-08 7:19 UTC (permalink / raw)
To: robh+dt, mripard, wens, mturquette, sboyd, gregory.clement, tglx,
jason, maz, srinivas.kandagatla, linus.walleij, anarsoul,
tiny.windzz, rui.zhang, daniel.lezcano, amit.kucheria, lee.jones,
p.zabel, clabbe, icenowy, megous, stefan, bage
Cc: devicetree, linux-pm, liyong, linux-kernel, linux-gpio,
huangshuosheng, linux-i2c, Frank Lee, linux-clk,
linux-arm-kernel
This patch set adds initial support for allwinner a100 soc,
which is a 64-bit tablet chip.
v3:
-Add pmu and nmi support
-Add read data mask for calibration
-Code style
-Some trivial things in yaml files
v2:
-Some naming consistency
-Repair email address
-Fix mmc clock
-Don't export system clock
-Fix checkpatch warning
-Drop unneeded pin function, convert to jtag_gpu and i2s_x
Frank Lee (16):
dt-bindings: clk: sunxi-ccu: add compatible string for A100 CCU and
R-CCU
clk: sunxi-ng: add support for the Allwinner A100 CCU
dt-bindings: pinctrl: sunxi: Add A100 pinctrl bindings
dt-bindings: pinctrl: sunxi: make gpio banks supplies required
pinctrl: sunxi: add support for the Allwinner A100 pin controller
dt-bindings: nvmem: SID: add binding for A100's SID controller
dt-bindings: thermal: sun8i: Add binding for A100's THS controller
thermal: sun8i: add TEMP_CALIB_MASK for calibration data in
sun50i_h6_ths_calibrate
thermal: sun8i: Add A100's THS controller support
mfd: axp20x: Allow the AXP803 to be probed by I2C
dt-bindings: irq: sun7i-nmi: fix dt-binding for a80 nmi
dt-bindings: irq: sun7i-nmi: Add binding for A100's NMI controller
dt-bindings: i2c: mv64xxx: Add compatible for the A100 i2c node.
arm64: allwinner: A100: add the basical Allwinner A100 DTSI file
dt-bindings: arm: sunxi: Add Allwinner A100 Perf1 Board bindings
arm64: allwinner: A100: add support for Allwinner Perf1 board
Documentation/devicetree/bindings/arm/sunxi.yaml | 5 +
.../bindings/clock/allwinner,sun4i-a10-ccu.yaml | 7 +-
.../bindings/i2c/marvell,mv64xxx-i2c.yaml | 3 +
.../allwinner,sun7i-a20-sc-nmi.yaml | 5 +-
.../bindings/nvmem/allwinner,sun4i-a10-sid.yaml | 3 +
.../pinctrl/allwinner,sun4i-a10-pinctrl.yaml | 75 +-
.../bindings/thermal/allwinner,sun8i-a83t-ths.yaml | 6 +-
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../dts/allwinner/sun50i-a100-allwinner-perf1.dts | 180 +++
arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi | 364 ++++++
drivers/clk/sunxi-ng/Kconfig | 10 +
drivers/clk/sunxi-ng/Makefile | 2 +
drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c | 214 ++++
drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h | 21 +
drivers/clk/sunxi-ng/ccu-sun50i-a100.c | 1276 ++++++++++++++++++++
drivers/clk/sunxi-ng/ccu-sun50i-a100.h | 56 +
drivers/mfd/axp20x-i2c.c | 2 +
drivers/pinctrl/sunxi/Kconfig | 10 +
drivers/pinctrl/sunxi/Makefile | 2 +
drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c | 105 ++
drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c | 708 +++++++++++
drivers/thermal/sun8i_thermal.c | 16 +-
include/dt-bindings/clock/sun50i-a100-ccu.h | 116 ++
include/dt-bindings/clock/sun50i-a100-r-ccu.h | 23 +
include/dt-bindings/reset/sun50i-a100-ccu.h | 68 ++
include/dt-bindings/reset/sun50i-a100-r-ccu.h | 18 +
26 files changed, 3262 insertions(+), 34 deletions(-)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a100-allwinner-perf1.dts
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100.c
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100.h
create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c
create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c
create mode 100644 include/dt-bindings/clock/sun50i-a100-ccu.h
create mode 100644 include/dt-bindings/clock/sun50i-a100-r-ccu.h
create mode 100644 include/dt-bindings/reset/sun50i-a100-ccu.h
create mode 100644 include/dt-bindings/reset/sun50i-a100-r-ccu.h
--
1.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 22+ messages in thread
* [PATCH v3 01/16] dt-bindings: clk: sunxi-ccu: add compatible string for A100 CCU and R-CCU
2020-07-08 7:19 [PATCH v3 00/16] Allwinner A100 Initial support Frank Lee
@ 2020-07-08 7:19 ` Frank Lee
2020-07-13 22:54 ` Rob Herring
2020-07-08 7:19 ` [PATCH v3 02/16] clk: sunxi-ng: add support for the Allwinner A100 CCU Frank Lee
` (9 subsequent siblings)
10 siblings, 1 reply; 22+ messages in thread
From: Frank Lee @ 2020-07-08 7:19 UTC (permalink / raw)
To: robh+dt, mripard, wens, mturquette, sboyd, gregory.clement, tglx,
jason, maz, srinivas.kandagatla, linus.walleij, anarsoul,
tiny.windzz, rui.zhang, daniel.lezcano, amit.kucheria, lee.jones,
p.zabel, clabbe, icenowy, megous, stefan, bage
Cc: devicetree, linux-pm, liyong, linux-kernel, linux-gpio,
huangshuosheng, linux-i2c, Frank Lee, linux-clk,
linux-arm-kernel
This patch adds binding to a100's ccu clock and r-ccu clock.
Signed-off-by: Frank Lee <frank@allwinnertech.com>
---
.../devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml | 7 ++++++-
1 file changed, 6 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml b/Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml
index 4d38212..3b45344 100644
--- a/Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml
+++ b/Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml
@@ -36,6 +36,8 @@ properties:
- allwinner,sun9i-a80-ccu
- allwinner,sun50i-a64-ccu
- allwinner,sun50i-a64-r-ccu
+ - allwinner,sun50i-a100-ccu
+ - allwinner,sun50i-a100-r-ccu
- allwinner,sun50i-h5-ccu
- allwinner,sun50i-h6-ccu
- allwinner,sun50i-h6-r-ccu
@@ -78,6 +80,7 @@ if:
- allwinner,sun8i-a83t-r-ccu
- allwinner,sun8i-h3-r-ccu
- allwinner,sun50i-a64-r-ccu
+ - allwinner,sun50i-a100-r-ccu
- allwinner,sun50i-h6-r-ccu
then:
@@ -94,7 +97,9 @@ else:
if:
properties:
compatible:
- const: allwinner,sun50i-h6-ccu
+ enum:
+ - allwinner,sun50i-a100-ccu
+ - allwinner,sun50i-h6-ccu
then:
properties:
--
1.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH v3 02/16] clk: sunxi-ng: add support for the Allwinner A100 CCU
2020-07-08 7:19 [PATCH v3 00/16] Allwinner A100 Initial support Frank Lee
2020-07-08 7:19 ` [PATCH v3 01/16] dt-bindings: clk: sunxi-ccu: add compatible string for A100 CCU and R-CCU Frank Lee
@ 2020-07-08 7:19 ` Frank Lee
2020-07-08 7:19 ` [PATCH v3 03/16] dt-bindings: pinctrl: sunxi: Add A100 pinctrl bindings Frank Lee
` (8 subsequent siblings)
10 siblings, 0 replies; 22+ messages in thread
From: Frank Lee @ 2020-07-08 7:19 UTC (permalink / raw)
To: robh+dt, mripard, wens, mturquette, sboyd, gregory.clement, tglx,
jason, maz, srinivas.kandagatla, linus.walleij, anarsoul,
tiny.windzz, rui.zhang, daniel.lezcano, amit.kucheria, lee.jones,
p.zabel, clabbe, icenowy, megous, stefan, bage
Cc: devicetree, linux-pm, liyong, linux-kernel, linux-gpio,
huangshuosheng, linux-i2c, Frank Lee, linux-clk,
linux-arm-kernel
Add support for a100 in the sunxi-ng CCU framework.
Signed-off-by: Frank Lee <frank@allwinnertech.com>
---
drivers/clk/sunxi-ng/Kconfig | 10 +
drivers/clk/sunxi-ng/Makefile | 2 +
drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c | 214 +++++
drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h | 21 +
drivers/clk/sunxi-ng/ccu-sun50i-a100.c | 1276 +++++++++++++++++++++++++
drivers/clk/sunxi-ng/ccu-sun50i-a100.h | 56 ++
include/dt-bindings/clock/sun50i-a100-ccu.h | 116 +++
include/dt-bindings/clock/sun50i-a100-r-ccu.h | 23 +
include/dt-bindings/reset/sun50i-a100-ccu.h | 68 ++
include/dt-bindings/reset/sun50i-a100-r-ccu.h | 18 +
10 files changed, 1804 insertions(+)
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100.c
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100.h
create mode 100644 include/dt-bindings/clock/sun50i-a100-ccu.h
create mode 100644 include/dt-bindings/clock/sun50i-a100-r-ccu.h
create mode 100644 include/dt-bindings/reset/sun50i-a100-ccu.h
create mode 100644 include/dt-bindings/reset/sun50i-a100-r-ccu.h
diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig
index cdf3330..ce5f584 100644
--- a/drivers/clk/sunxi-ng/Kconfig
+++ b/drivers/clk/sunxi-ng/Kconfig
@@ -17,6 +17,16 @@ config SUN50I_A64_CCU
default ARM64 && ARCH_SUNXI
depends on (ARM64 && ARCH_SUNXI) || COMPILE_TEST
+config SUN50I_A100_CCU
+ bool "Support for the Allwinner A100 CCU"
+ default ARM64 && ARCH_SUNXI
+ depends on (ARM64 && ARCH_SUNXI) || COMPILE_TEST
+
+config SUN50I_A100_R_CCU
+ bool "Support for the Allwinner A100 PRCM CCU"
+ default ARM64 && ARCH_SUNXI
+ depends on (ARM64 && ARCH_SUNXI) || COMPILE_TEST
+
config SUN50I_H6_CCU
bool "Support for the Allwinner H6 CCU"
default ARM64 && ARCH_SUNXI
diff --git a/drivers/clk/sunxi-ng/Makefile b/drivers/clk/sunxi-ng/Makefile
index 4c7bee8..3eb5cff 100644
--- a/drivers/clk/sunxi-ng/Makefile
+++ b/drivers/clk/sunxi-ng/Makefile
@@ -23,6 +23,8 @@ obj-y += ccu_mp.o
# SoC support
obj-$(CONFIG_SUNIV_F1C100S_CCU) += ccu-suniv-f1c100s.o
obj-$(CONFIG_SUN50I_A64_CCU) += ccu-sun50i-a64.o
+obj-$(CONFIG_SUN50I_A100_CCU) += ccu-sun50i-a100.o
+obj-$(CONFIG_SUN50I_A100_R_CCU) += ccu-sun50i-a100-r.o
obj-$(CONFIG_SUN50I_H6_CCU) += ccu-sun50i-h6.o
obj-$(CONFIG_SUN50I_H6_R_CCU) += ccu-sun50i-h6-r.o
obj-$(CONFIG_SUN4I_A10_CCU) += ccu-sun4i-a10.o
diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c b/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c
new file mode 100644
index 0000000..d6dbd355
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c
@@ -0,0 +1,214 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2020 Frank Lee <frank@allwinnertech.com>
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+
+#include "ccu_common.h"
+#include "ccu_reset.h"
+
+#include "ccu_div.h"
+#include "ccu_gate.h"
+#include "ccu_mp.h"
+#include "ccu_nm.h"
+
+#include "ccu-sun50i-a100-r.h"
+
+static const char * const cpus_r_apb2_parents[] = { "dcxo24M", "osc32k",
+ "iosc", "pll-periph0" };
+static const struct ccu_mux_var_prediv cpus_r_apb2_predivs[] = {
+ { .index = 3, .shift = 0, .width = 5 },
+};
+
+static struct ccu_div r_cpus_clk = {
+ .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+
+ .mux = {
+ .shift = 24,
+ .width = 2,
+
+ .var_predivs = cpus_r_apb2_predivs,
+ .n_var_predivs = ARRAY_SIZE(cpus_r_apb2_predivs),
+ },
+
+ .common = {
+ .reg = 0x000,
+ .features = CCU_FEATURE_VARIABLE_PREDIV,
+ .hw.init = CLK_HW_INIT_PARENTS("cpus",
+ cpus_r_apb2_parents,
+ &ccu_div_ops,
+ 0),
+ },
+};
+
+static CLK_FIXED_FACTOR_HW(r_ahb_clk, "r-ahb", &r_cpus_clk.common.hw, 1, 1, 0);
+
+static struct ccu_div r_apb1_clk = {
+ .div = _SUNXI_CCU_DIV(0, 2),
+
+ .common = {
+ .reg = 0x00c,
+ .hw.init = CLK_HW_INIT("r-apb1",
+ "r-ahb",
+ &ccu_div_ops,
+ 0),
+ },
+};
+
+static struct ccu_div r_apb2_clk = {
+ .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+
+ .mux = {
+ .shift = 24,
+ .width = 2,
+
+ .var_predivs = cpus_r_apb2_predivs,
+ .n_var_predivs = ARRAY_SIZE(cpus_r_apb2_predivs),
+ },
+
+ .common = {
+ .reg = 0x010,
+ .features = CCU_FEATURE_VARIABLE_PREDIV,
+ .hw.init = CLK_HW_INIT_PARENTS("r-apb2",
+ cpus_r_apb2_parents,
+ &ccu_div_ops,
+ 0),
+ },
+};
+
+static const struct clk_parent_data clk_parent_r_apb1[] = {
+ { .hw = &r_apb1_clk.common.hw },
+};
+
+static const struct clk_parent_data clk_parent_r_apb2[] = {
+ { .hw = &r_apb2_clk.common.hw },
+};
+
+static SUNXI_CCU_GATE_DATA(r_apb1_timer_clk, "r-apb1-timer", clk_parent_r_apb1,
+ 0x11c, BIT(0), 0);
+
+static SUNXI_CCU_GATE_DATA(r_apb1_twd_clk, "r-apb1-twd", clk_parent_r_apb1,
+ 0x12c, BIT(0), 0);
+
+static const char * const r_apb1_pwm_clk_parents[] = { "dcxo24M", "osc32k",
+ "iosc" };
+static SUNXI_CCU_MUX(r_apb1_pwm_clk, "r-apb1-pwm", r_apb1_pwm_clk_parents,
+ 0x130, 24, 2, 0);
+
+static SUNXI_CCU_GATE_DATA(r_apb1_bus_pwm_clk, "r-apb1-bus-pwm",
+ clk_parent_r_apb1, 0x13c, BIT(0), 0);
+
+static SUNXI_CCU_GATE_DATA(r_apb1_ppu_clk, "r-apb1-ppu", clk_parent_r_apb1,
+ 0x17c, BIT(0), 0);
+
+static SUNXI_CCU_GATE_DATA(r_apb2_uart_clk, "r-apb2-uart", clk_parent_r_apb2,
+ 0x18c, BIT(0), 0);
+
+static SUNXI_CCU_GATE_DATA(r_apb2_i2c0_clk, "r-apb2-i2c0", clk_parent_r_apb2,
+ 0x19c, BIT(0), 0);
+
+static SUNXI_CCU_GATE_DATA(r_apb2_i2c1_clk, "r-apb2-i2c1", clk_parent_r_apb2,
+ 0x19c, BIT(1), 0);
+
+static const char * const r_apb1_ir_rx_parents[] = { "osc32k", "dcxo24M" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(r_apb1_ir_rx_clk, "r-apb1-ir-rx",
+ r_apb1_ir_rx_parents, 0x1c0,
+ 0, 5, /* M */
+ 8, 2, /* P */
+ 24, 1, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE_DATA(r_apb1_bus_ir_rx_clk, "r-apb1-bus-ir-rx",
+ clk_parent_r_apb1, 0x1cc, BIT(0), 0);
+
+static SUNXI_CCU_GATE(r_ahb_bus_rtc_clk, "r-ahb-rtc", "r-ahb",
+ 0x20c, BIT(0), 0);
+
+static struct ccu_common *sun50i_a100_r_ccu_clks[] = {
+ &r_cpus_clk.common,
+ &r_apb1_clk.common,
+ &r_apb2_clk.common,
+ &r_apb1_timer_clk.common,
+ &r_apb1_twd_clk.common,
+ &r_apb1_pwm_clk.common,
+ &r_apb1_bus_pwm_clk.common,
+ &r_apb1_ppu_clk.common,
+ &r_apb2_uart_clk.common,
+ &r_apb2_i2c0_clk.common,
+ &r_apb2_i2c1_clk.common,
+ &r_apb1_ir_rx_clk.common,
+ &r_apb1_bus_ir_rx_clk.common,
+ &r_ahb_bus_rtc_clk.common,
+};
+
+static struct clk_hw_onecell_data sun50i_a100_r_hw_clks = {
+ .hws = {
+ [CLK_R_CPUS] = &r_cpus_clk.common.hw,
+ [CLK_R_AHB] = &r_ahb_clk.hw,
+ [CLK_R_APB1] = &r_apb1_clk.common.hw,
+ [CLK_R_APB2] = &r_apb2_clk.common.hw,
+ [CLK_R_APB1_TIMER] = &r_apb1_timer_clk.common.hw,
+ [CLK_R_APB1_TWD] = &r_apb1_twd_clk.common.hw,
+ [CLK_R_APB1_PWM] = &r_apb1_pwm_clk.common.hw,
+ [CLK_R_APB1_BUS_PWM] = &r_apb1_bus_pwm_clk.common.hw,
+ [CLK_R_APB1_PPU] = &r_apb1_ppu_clk.common.hw,
+ [CLK_R_APB2_UART] = &r_apb2_uart_clk.common.hw,
+ [CLK_R_APB2_I2C0] = &r_apb2_i2c0_clk.common.hw,
+ [CLK_R_APB2_I2C1] = &r_apb2_i2c1_clk.common.hw,
+ [CLK_R_APB1_IR] = &r_apb1_ir_rx_clk.common.hw,
+ [CLK_R_APB1_BUS_IR] = &r_apb1_bus_ir_rx_clk.common.hw,
+ [CLK_R_AHB_BUS_RTC] = &r_ahb_bus_rtc_clk.common.hw,
+ },
+ .num = CLK_NUMBER,
+};
+
+static struct ccu_reset_map sun50i_a100_r_ccu_resets[] = {
+ [RST_R_APB1_TIMER] = { 0x11c, BIT(16) },
+ [RST_R_APB1_BUS_PWM] = { 0x13c, BIT(16) },
+ [RST_R_APB1_PPU] = { 0x17c, BIT(16) },
+ [RST_R_APB2_UART] = { 0x18c, BIT(16) },
+ [RST_R_APB2_I2C0] = { 0x19c, BIT(16) },
+ [RST_R_APB2_I2C1] = { 0x19c, BIT(17) },
+ [RST_R_APB1_BUS_IR] = { 0x1cc, BIT(16) },
+ [RST_R_AHB_BUS_RTC] = { 0x20c, BIT(16) },
+};
+
+static const struct sunxi_ccu_desc sun50i_a100_r_ccu_desc = {
+ .ccu_clks = sun50i_a100_r_ccu_clks,
+ .num_ccu_clks = ARRAY_SIZE(sun50i_a100_r_ccu_clks),
+
+ .hw_clks = &sun50i_a100_r_hw_clks,
+
+ .resets = sun50i_a100_r_ccu_resets,
+ .num_resets = ARRAY_SIZE(sun50i_a100_r_ccu_resets),
+};
+
+static int sun50i_a100_r_ccu_probe(struct platform_device *pdev)
+{
+ void __iomem *reg;
+
+ reg = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(reg))
+ return PTR_ERR(reg);
+
+ return sunxi_ccu_probe(pdev->dev.of_node, reg, &sun50i_a100_r_ccu_desc);
+}
+
+static const struct of_device_id sun50i_a100_r_ccu_ids[] = {
+ { .compatible = "allwinner,sun50i-a100-r-ccu" },
+ { }
+};
+
+static struct platform_driver sun50i_a100_r_ccu_driver = {
+ .probe = sun50i_a100_r_ccu_probe,
+ .driver = {
+ .name = "sun50i-a100-r-ccu",
+ .of_match_table = sun50i_a100_r_ccu_ids,
+ },
+};
+module_platform_driver(sun50i_a100_r_ccu_driver);
diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h b/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h
new file mode 100644
index 0000000..8331fbc
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h
@@ -0,0 +1,21 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2020 Frank Lee <frank@allwinnertech.com>
+ */
+
+#ifndef _CCU_SUN50I_A100_R_H
+#define _CCU_SUN50I_A100_R_H
+
+#include <dt-bindings/clock/sun50i-a100-r-ccu.h>
+#include <dt-bindings/reset/sun50i-a100-r-ccu.h>
+
+#define CLK_R_CPUS 0
+#define CLK_R_AHB 1
+
+/* exported except APB1 for R_PIO */
+
+#define CLK_R_APB2 3
+
+#define CLK_NUMBER (CLK_R_AHB_BUS_RTC + 1)
+
+#endif /* _CCU_SUN50I_A100_R_H */
diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-a100.c b/drivers/clk/sunxi-ng/ccu-sun50i-a100.c
new file mode 100644
index 0000000..98f32f8
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu-sun50i-a100.c
@@ -0,0 +1,1276 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2020 Frank Lee <frank@allwinnertech.com>
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+
+#include "ccu_common.h"
+#include "ccu_reset.h"
+
+#include "ccu_div.h"
+#include "ccu_gate.h"
+#include "ccu_mp.h"
+#include "ccu_mult.h"
+#include "ccu_nk.h"
+#include "ccu_nkm.h"
+#include "ccu_nkmp.h"
+#include "ccu_nm.h"
+
+#include "ccu-sun50i-a100.h"
+
+#define SUN50I_A100_PLL_SDM_ENABLE BIT(24)
+#define SUN50I_A100_PLL_OUTPUT_ENABLE BIT(27)
+#define SUN50I_A100_PLL_LOCK BIT(28)
+#define SUN50I_A100_PLL_LOCK_ENABLE BIT(29)
+#define SUN50I_A100_PLL_ENABLE BIT(31)
+
+#define SUN50I_A100_PLL_PERIPH1_PATTERN0 0xd1303333
+
+/*
+ * The CPU PLL is actually NP clock, with P being /1, /2 or /4. However
+ * P should only be used for output frequencies lower than 288 MHz.
+ *
+ * For now we can just model it as a multiplier clock, and force P to /1.
+ *
+ * The M factor is present in the register's description, but not in the
+ * frequency formula, and it's documented as "M is only used for backdoor
+ * testing", so it's not modelled and then force to 0.
+ */
+#define SUN50I_A100_PLL_CPUX_REG 0x000
+static struct ccu_mult pll_cpux_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .mult = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .common = {
+ .reg = 0x000,
+ .hw.init = CLK_HW_INIT("pll-cpux", "dcxo24M",
+ &ccu_mult_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+/* Some PLLs are input * N / div1 / P. Model them as NKMP with no K */
+#define SUN50I_A100_PLL_DDR0_REG 0x010
+static struct ccu_nkmp pll_ddr0_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .p = _SUNXI_CCU_DIV(0, 1), /* output divider */
+ .common = {
+ .reg = 0x010,
+ .hw.init = CLK_HW_INIT("pll-ddr0", "dcxo24M",
+ &ccu_nkmp_ops,
+ CLK_SET_RATE_UNGATE |
+ CLK_IS_CRITICAL),
+ },
+};
+
+#define SUN50I_A100_PLL_PERIPH0_REG 0x020
+static struct ccu_nkmp pll_periph0_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .p = _SUNXI_CCU_DIV(0, 1), /* output divider */
+ .fixed_post_div = 2,
+ .common = {
+ .reg = 0x020,
+ .features = CCU_FEATURE_FIXED_POSTDIV,
+ .hw.init = CLK_HW_INIT("pll-periph0", "dcxo24M",
+ &ccu_nkmp_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+#define SUN50I_A100_PLL_PERIPH1_REG 0x028
+static struct ccu_nkmp pll_periph1_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .p = _SUNXI_CCU_DIV(0, 1), /* output divider */
+ .fixed_post_div = 2,
+ .common = {
+ .reg = 0x028,
+ .features = CCU_FEATURE_FIXED_POSTDIV,
+ .hw.init = CLK_HW_INIT("pll-periph1", "dcxo24M",
+ &ccu_nkmp_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+#define SUN50I_A100_PLL_PERIPH1_PATTERN0_REG 0x128
+
+#define SUN50I_A100_PLL_GPU_REG 0x030
+static struct ccu_nkmp pll_gpu_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .p = _SUNXI_CCU_DIV(0, 1), /* output divider */
+ .common = {
+ .reg = 0x030,
+ .hw.init = CLK_HW_INIT("pll-gpu", "dcxo24M",
+ &ccu_nkmp_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+/*
+ * For Video PLLs, the output divider is described as "used for testing"
+ * in the user manual. So it's not modelled and forced to 0.
+ */
+#define SUN50I_A100_PLL_VIDEO0_REG 0x040
+static struct ccu_nm pll_video0_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .fixed_post_div = 4,
+ .common = {
+ .reg = 0x040,
+ .features = CCU_FEATURE_FIXED_POSTDIV,
+ .hw.init = CLK_HW_INIT("pll-video0", "dcxo24M",
+ &ccu_nm_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+#define SUN50I_A100_PLL_VIDEO1_REG 0x048
+static struct ccu_nm pll_video1_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .fixed_post_div = 4,
+ .common = {
+ .reg = 0x048,
+ .features = CCU_FEATURE_FIXED_POSTDIV,
+ .hw.init = CLK_HW_INIT("pll-video1", "dcxo24M",
+ &ccu_nm_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+#define SUN50I_A100_PLL_VIDEO2_REG 0x050
+static struct ccu_nm pll_video2_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .fixed_post_div = 4,
+ .common = {
+ .reg = 0x050,
+ .features = CCU_FEATURE_FIXED_POSTDIV,
+ .hw.init = CLK_HW_INIT("pll-video2", "dcxo24M",
+ &ccu_nm_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+#define SUN50I_A100_PLL_VE_REG 0x058
+static struct ccu_nkmp pll_ve_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .p = _SUNXI_CCU_DIV(0, 1), /* output divider */
+ .common = {
+ .reg = 0x058,
+ .hw.init = CLK_HW_INIT("pll-ve", "dcxo24M",
+ &ccu_nkmp_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+/*
+ * The COM PLL has m0 dividers in addition to the usual N, M
+ * factors. Since we only need 1 frequencies from this PLL: 45.1584 MHz,
+ * ignore it for now.
+ */
+#define SUN50I_A100_PLL_COM_REG 0x060
+static struct ccu_sdm_setting pll_com_sdm_table[] = {
+ { .rate = 451584000, .pattern = 0xc0014396, .m = 2, .n = 37 },
+};
+
+static struct ccu_nm pll_com_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(0, 1),
+ .sdm = _SUNXI_CCU_SDM(pll_com_sdm_table, BIT(24),
+ 0x160, BIT(31)),
+ .common = {
+ .reg = 0x060,
+ .features = CCU_FEATURE_SIGMA_DELTA_MOD,
+ .hw.init = CLK_HW_INIT("pll-com", "dcxo24M",
+ &ccu_nm_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+#define SUN50I_A100_PLL_VIDEO3_REG 0x068
+static struct ccu_nm pll_video3_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .fixed_post_div = 4,
+ .common = {
+ .reg = 0x068,
+ .features = CCU_FEATURE_FIXED_POSTDIV,
+ .hw.init = CLK_HW_INIT("pll-video3", "dcxo24M",
+ &ccu_nm_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+/*
+ * The Audio PLL has m0, m1 dividers in addition to the usual N, M
+ * factors. Since we only need 4 frequencies from this PLL: 22.5792 MHz,
+ * 24.576 MHz, 90.3168MHz and 98.304MHz ignore them for now.
+ * Enforce the default for them, which is m0 = 1, m1 = 0.
+ */
+#define SUN50I_A100_PLL_AUDIO_REG 0x078
+static struct ccu_sdm_setting pll_audio_sdm_table[] = {
+ { .rate = 45158400, .pattern = 0xc001bcd3, .m = 18, .n = 33 },
+ { .rate = 49152000, .pattern = 0xc001eb85, .m = 20, .n = 40 },
+ { .rate = 180633600, .pattern = 0xc001288d, .m = 3, .n = 22 },
+ { .rate = 196608000, .pattern = 0xc001eb85, .m = 5, .n = 40 },
+};
+
+static struct ccu_nm pll_audio_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(16, 6),
+ .fixed_post_div = 2,
+ .sdm = _SUNXI_CCU_SDM(pll_audio_sdm_table, BIT(24),
+ 0x178, BIT(31)),
+ .common = {
+ .reg = 0x078,
+ .features = CCU_FEATURE_FIXED_POSTDIV |
+ CCU_FEATURE_SIGMA_DELTA_MOD,
+ .hw.init = CLK_HW_INIT("pll-audio", "dcxo24M",
+ &ccu_nm_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+static const char * const cpux_parents[] = { "dcxo24M", "osc32k",
+ "iosc", "pll-cpux",
+ "pll-periph0" };
+static SUNXI_CCU_MUX(cpux_clk, "cpux", cpux_parents,
+ 0x500, 24, 3, CLK_SET_RATE_PARENT | CLK_IS_CRITICAL);
+static SUNXI_CCU_M(axi_clk, "axi", "cpux", 0x500, 0, 2, 0);
+static SUNXI_CCU_M(cpux_apb_clk, "cpux-apb", "cpux", 0x500, 8, 2, 0);
+
+static const char * const psi_ahb1_ahb2_parents[] = { "dcxo24M", "osc32k",
+ "iosc", "pll-periph0",
+ "pll-periph0-2x" };
+static SUNXI_CCU_MP_WITH_MUX(psi_ahb1_ahb2_clk, "psi-ahb1-ahb2",
+ psi_ahb1_ahb2_parents, 0x510,
+ 0, 2, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ 0);
+
+static const char * const ahb3_apb1_apb2_parents[] = { "dcxo24M", "osc32k",
+ "psi-ahb1-ahb2",
+ "pll-periph0",
+ "pll-periph0-2x" };
+static SUNXI_CCU_MP_WITH_MUX(ahb3_clk, "ahb3", ahb3_apb1_apb2_parents, 0x51c,
+ 0, 2, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX(apb1_clk, "apb1", ahb3_apb1_apb2_parents, 0x520,
+ 0, 2, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX(apb2_clk, "apb2", ahb3_apb1_apb2_parents, 0x524,
+ 0, 2, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ 0);
+
+static const char * const mbus_parents[] = { "dcxo24M", "pll-ddr0",
+ "pll-periph0",
+ "pll-periph0-2x" };
+static SUNXI_CCU_M_WITH_MUX_GATE(mbus_clk, "mbus", mbus_parents, 0x540,
+ 0, 3, /* M */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ CLK_IS_CRITICAL);
+
+static const char * const de_parents[] = { "pll-com", "pll-periph0-2x" };
+static SUNXI_CCU_M_WITH_MUX_GATE(de_clk, "de0", de_parents, 0x600,
+ 0, 4, /* M */
+ 24, 1, /* mux */
+ BIT(31), /* gate */
+ CLK_SET_RATE_PARENT);
+
+static SUNXI_CCU_GATE(bus_de_clk, "bus-de", "psi-ahb1-ahb2",
+ 0x60c, BIT(0), 0);
+
+static const char * const g2d_parents[] = { "pll-com", "pll-periph0-2x",
+ "pll-video0-2x", "pll-video1-2x",
+ "pll-video2-2x"};
+static SUNXI_CCU_M_WITH_MUX_GATE(g2d_clk, "g2d",
+ g2d_parents,
+ 0x630,
+ 0, 4, /* M */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_g2d_clk, "bus-g2d", "psi-ahb1-ahb2",
+ 0x63c, BIT(0), 0);
+
+static const char * const gpu_parents[] = { "pll-gpu" };
+static SUNXI_CCU_M_WITH_MUX_GATE(gpu_clk, "gpu", gpu_parents, 0x670,
+ 0, 2, /* M */
+ 24, 1, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_gpu_clk, "bus-gpu", "psi-ahb1-ahb2",
+ 0x67c, BIT(0), 0);
+
+static const char * const ce_parents[] = { "dcxo24M", "pll-periph0-2x" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(ce_clk, "ce", ce_parents, 0x680,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 1, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_ce_clk, "bus-ce", "psi-ahb1-ahb2",
+ 0x68c, BIT(0), 0);
+
+static const char * const ve_parents[] = { "pll-ve" };
+static SUNXI_CCU_M_WITH_MUX_GATE(ve_clk, "ve", ve_parents, 0x690,
+ 0, 3, /* M */
+ 24, 1, /* mux */
+ BIT(31), /* gate */
+ CLK_SET_RATE_PARENT);
+
+static SUNXI_CCU_GATE(bus_ve_clk, "bus-ve", "psi-ahb1-ahb2",
+ 0x69c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_dma_clk, "bus-dma", "psi-ahb1-ahb2",
+ 0x70c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_msgbox_clk, "bus-msgbox", "psi-ahb1-ahb2",
+ 0x71c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_spinlock_clk, "bus-spinlock", "psi-ahb1-ahb2",
+ 0x72c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_hstimer_clk, "bus-hstimer", "psi-ahb1-ahb2",
+ 0x73c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(avs_clk, "avs", "dcxo24M", 0x740, BIT(31), 0);
+
+static SUNXI_CCU_GATE(bus_dbg_clk, "bus-dbg", "psi-ahb1-ahb2",
+ 0x78c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_psi_clk, "bus-psi", "psi-ahb1-ahb2",
+ 0x79c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_pwm_clk, "bus-pwm", "apb1", 0x7ac, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_iommu_clk, "bus-iommu", "apb1", 0x7bc, BIT(0), 0);
+
+static SUNXI_CCU_GATE(mbus_dma_clk, "mbus-dma", "mbus",
+ 0x804, BIT(0), 0);
+static SUNXI_CCU_GATE(mbus_ve_clk, "mbus-ve", "mbus",
+ 0x804, BIT(1), 0);
+static SUNXI_CCU_GATE(mbus_ce_clk, "mbus-ce", "mbus",
+ 0x804, BIT(2), 0);
+static SUNXI_CCU_GATE(mbus_nand_clk, "mbus-nand", "mbus",
+ 0x804, BIT(5), 0);
+static SUNXI_CCU_GATE(mbus_csi_clk, "mbus-csi", "mbus",
+ 0x804, BIT(8), 0);
+static SUNXI_CCU_GATE(mbus_isp_clk, "mbus-isp", "mbus",
+ 0x804, BIT(9), 0);
+static SUNXI_CCU_GATE(mbus_g2d_clk, "mbus-g2d", "mbus",
+ 0x804, BIT(10), 0);
+
+static SUNXI_CCU_GATE(bus_dram_clk, "bus-dram", "psi-ahb1-ahb2",
+ 0x80c, BIT(0), CLK_IS_CRITICAL);
+
+static const char * const nand_spi_parents[] = { "dcxo24M",
+ "pll-periph0",
+ "pll-periph1",
+ "pll-periph0-2x",
+ "pll-periph1-2x" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(nand0_clk, "nand0", nand_spi_parents, 0x810,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(nand1_clk, "nand1", nand_spi_parents, 0x814,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_nand_clk, "bus-nand", "ahb3", 0x82c, BIT(0), 0);
+
+static const char * const mmc_parents[] = { "dcxo24M", "pll-periph0-2x",
+ "pll-periph1-2x" };
+static SUNXI_CCU_MP_WITH_MUX_GATE_POSTDIV(mmc0_clk, "mmc0", mmc_parents, 0x830,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 2, /* post-div */
+ CLK_SET_RATE_NO_REPARENT);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE_POSTDIV(mmc1_clk, "mmc1", mmc_parents, 0x834,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 2, /* post-div */
+ CLK_SET_RATE_NO_REPARENT);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE_POSTDIV(mmc2_clk, "mmc2", mmc_parents, 0x838,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 2, /* post-div */
+ CLK_SET_RATE_NO_REPARENT);
+
+static SUNXI_CCU_GATE(bus_mmc0_clk, "bus-mmc0", "ahb3", 0x84c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_mmc1_clk, "bus-mmc1", "ahb3", 0x84c, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_mmc2_clk, "bus-mmc2", "ahb3", 0x84c, BIT(2), 0);
+
+static SUNXI_CCU_GATE(bus_uart0_clk, "bus-uart0", "apb2", 0x90c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_uart1_clk, "bus-uart1", "apb2", 0x90c, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_uart2_clk, "bus-uart2", "apb2", 0x90c, BIT(2), 0);
+static SUNXI_CCU_GATE(bus_uart3_clk, "bus-uart3", "apb2", 0x90c, BIT(3), 0);
+static SUNXI_CCU_GATE(bus_uart4_clk, "bus-uart4", "apb2", 0x90c, BIT(4), 0);
+
+static SUNXI_CCU_GATE(bus_i2c0_clk, "bus-i2c0", "apb2", 0x91c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_i2c1_clk, "bus-i2c1", "apb2", 0x91c, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_i2c2_clk, "bus-i2c2", "apb2", 0x91c, BIT(2), 0);
+static SUNXI_CCU_GATE(bus_i2c3_clk, "bus-i2c3", "apb2", 0x91c, BIT(3), 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(spi0_clk, "spi0", nand_spi_parents, 0x940,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(spi1_clk, "spi1", nand_spi_parents, 0x944,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(spi2_clk, "spi2", nand_spi_parents, 0x948,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_spi0_clk, "bus-spi0", "ahb3", 0x96c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_spi1_clk, "bus-spi1", "ahb3", 0x96c, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_spi2_clk, "bus-spi2", "ahb3", 0x96c, BIT(2), 0);
+
+static SUNXI_CCU_GATE(emac_25m_clk, "emac-25m", "ahb3", 0x970,
+ BIT(31) | BIT(30), 0);
+
+static SUNXI_CCU_GATE(bus_emac_clk, "bus-emac", "ahb3", 0x97c, BIT(0), 0);
+
+static const char * const ir_parents[] = { "osc32k", "iosc",
+ "pll-periph0", "pll-periph1" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(ir_rx_clk, "ir-rx", ir_parents, 0x990,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_ir_rx_clk, "bus-ir-rx", "ahb3", 0x99c, BIT(0), 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(ir_tx_clk, "ir-tx", ir_parents, 0x9c0,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_ir_tx_clk, "bus-ir-tx", "apb1", 0x9cc, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_gpadc_clk, "bus-gpadc", "apb1", 0x9ec, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_ths_clk, "bus-ths", "apb1", 0x9fc, BIT(0), 0);
+
+static const char * const audio_parents[] = { "pll-audio", "pll-com-audio" };
+static struct ccu_div i2s0_clk = {
+ .enable = BIT(31),
+ .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+ .mux = _SUNXI_CCU_MUX(24, 2),
+ .common = {
+ .reg = 0xa10,
+ .hw.init = CLK_HW_INIT_PARENTS("i2s0",
+ audio_parents,
+ &ccu_div_ops,
+ CLK_SET_RATE_PARENT),
+ },
+};
+
+static struct ccu_div i2s1_clk = {
+ .enable = BIT(31),
+ .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+ .mux = _SUNXI_CCU_MUX(24, 2),
+ .common = {
+ .reg = 0xa14,
+ .hw.init = CLK_HW_INIT_PARENTS("i2s1",
+ audio_parents,
+ &ccu_div_ops,
+ CLK_SET_RATE_PARENT),
+ },
+};
+
+static struct ccu_div i2s2_clk = {
+ .enable = BIT(31),
+ .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+ .mux = _SUNXI_CCU_MUX(24, 2),
+ .common = {
+ .reg = 0xa18,
+ .hw.init = CLK_HW_INIT_PARENTS("i2s2",
+ audio_parents,
+ &ccu_div_ops,
+ CLK_SET_RATE_PARENT),
+ },
+};
+
+static struct ccu_div i2s3_clk = {
+ .enable = BIT(31),
+ .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+ .mux = _SUNXI_CCU_MUX(24, 2),
+ .common = {
+ .reg = 0xa1c,
+ .hw.init = CLK_HW_INIT_PARENTS("i2s3",
+ audio_parents,
+ &ccu_div_ops,
+ CLK_SET_RATE_PARENT),
+ },
+};
+
+static SUNXI_CCU_GATE(bus_i2s0_clk, "bus-i2s0", "apb1", 0xa20, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_i2s1_clk, "bus-i2s1", "apb1", 0xa20, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_i2s2_clk, "bus-i2s2", "apb1", 0xa20, BIT(2), 0);
+static SUNXI_CCU_GATE(bus_i2s3_clk, "bus-i2s3", "apb1", 0xa20, BIT(3), 0);
+
+static struct ccu_div spdif_clk = {
+ .enable = BIT(31),
+ .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+ .mux = _SUNXI_CCU_MUX(24, 2),
+ .common = {
+ .reg = 0xa24,
+ .hw.init = CLK_HW_INIT_PARENTS("spdif",
+ audio_parents,
+ &ccu_div_ops,
+ 0),
+ },
+};
+
+static SUNXI_CCU_GATE(bus_spdif_clk, "bus-spdif", "apb1", 0xa2c, BIT(0), 0);
+
+static struct ccu_div dmic_clk = {
+ .enable = BIT(31),
+ .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+ .mux = _SUNXI_CCU_MUX(24, 2),
+ .common = {
+ .reg = 0xa40,
+ .hw.init = CLK_HW_INIT_PARENTS("dmic",
+ audio_parents,
+ &ccu_div_ops,
+ 0),
+ },
+};
+
+static SUNXI_CCU_GATE(bus_dmic_clk, "bus-dmic", "apb1", 0xa4c, BIT(0), 0);
+
+static SUNXI_CCU_M_WITH_MUX_GATE(audio_codec_dac_clk, "audio-codec-dac",
+ audio_parents, 0xa50,
+ 0, 4, /* M */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_M_WITH_MUX_GATE(audio_codec_adc_clk, "audio-codec-adc",
+ audio_parents, 0xa54,
+ 0, 4, /* M */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_M_WITH_MUX_GATE(audio_codec_4x_clk, "audio-codec-4x",
+ audio_parents, 0xa58,
+ 0, 4, /* M */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_audio_codec_clk, "bus-audio-codec", "apb1", 0xa5c,
+ BIT(0), 0);
+
+/*
+ * There are OHCI 12M clock source selection bits for 2 USB 2.0 ports.
+ * We will force them to 0 (12M divided from 48M).
+ */
+#define SUN50I_A100_USB0_CLK_REG 0xa70
+#define SUN50I_A100_USB1_CLK_REG 0xa74
+
+static SUNXI_CCU_GATE(usb_ohci0_clk, "usb-ohci0", "osc12M", 0xa70, BIT(31), 0);
+static SUNXI_CCU_GATE(usb_phy0_clk, "usb-phy0", "dcxo24M", 0xa70, BIT(29), 0);
+
+static SUNXI_CCU_GATE(usb_ohci1_clk, "usb-ohci1", "osc12M", 0xa74, BIT(31), 0);
+static SUNXI_CCU_GATE(usb_phy1_clk, "usb-phy1", "dcxo24M", 0xa74, BIT(29), 0);
+
+static SUNXI_CCU_GATE(bus_ohci0_clk, "bus-ohci0", "ahb3", 0xa8c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_ohci1_clk, "bus-ohci1", "ahb3", 0xa8c, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_ehci0_clk, "bus-ehci0", "ahb3", 0xa8c, BIT(4), 0);
+static SUNXI_CCU_GATE(bus_ehci1_clk, "bus-ehci1", "ahb3", 0xa8c, BIT(5), 0);
+static SUNXI_CCU_GATE(bus_otg_clk, "bus-otg", "ahb3", 0xa8c, BIT(8), 0);
+
+static SUNXI_CCU_GATE(bus_lradc_clk, "bus-lradc", "ahb3", 0xa9c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_dpss_top0_clk, "bus-dpss-top0", "ahb3",
+ 0xabc, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_dpss_top1_clk, "bus-dpss-top1", "ahb3",
+ 0xacc, BIT(0), 0);
+
+static const char * const mipi_dsi_parents[] = { "dcxo24M", "pll-periph0-2x",
+ "pll-periph0" };
+static SUNXI_CCU_M_WITH_MUX_GATE(mipi_dsi_clk, "mipi-dsi",
+ mipi_dsi_parents,
+ 0xb24,
+ 0, 4, /* M */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_mipi_dsi_clk, "bus-mipi-dsi", "ahb3",
+ 0xb4c, BIT(0), 0);
+
+static const char * const tcon_lcd_parents[] = { "pll-video0-4x",
+ "pll-video1-4x",
+ "pll-video2-4x",
+ "pll-video3-4x",
+ "pll-periph0-2x" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(tcon_lcd_clk, "tcon-lcd0",
+ tcon_lcd_parents, 0xb60,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_tcon_lcd_clk, "bus-tcon-lcd0", "ahb3",
+ 0xb7c, BIT(0), 0);
+
+static const char * const ledc_parents[] = { "dcxo24M",
+ "pll-periph0" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(ledc_clk, "ledc",
+ ledc_parents, 0xbf0,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_ledc_clk, "bus-ledc", "ahb3", 0xbfc, BIT(0), 0);
+
+static const char * const csi_top_parents[] = { "pll-periph0-2x",
+ "pll-video0-2x",
+ "pll-video1-2x",
+ "pll-video2-2x",
+ "pll-video3-2x" };
+static SUNXI_CCU_M_WITH_MUX_GATE(csi_top_clk, "csi-top",
+ csi_top_parents, 0xc04,
+ 0, 4, /* M */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static const char * const csi0_mclk_parents[] = { "dcxo24M", "pll-video2",
+ "pll-video3", "pll-video0",
+ "pll-video1" };
+static SUNXI_CCU_M_WITH_MUX_GATE(csi0_mclk_clk, "csi0-mclk",
+ csi0_mclk_parents, 0xc08,
+ 0, 5, /* M */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static const char * const csi1_mclk_parents[] = { "dcxo24M", "pll-video3",
+ "pll-video0", "pll-video1",
+ "pll-video2" };
+static SUNXI_CCU_M_WITH_MUX_GATE(csi1_mclk_clk, "csi1-mclk",
+ csi1_mclk_parents, 0xc0c,
+ 0, 5, /* M */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_csi_clk, "bus-csi", "ahb3", 0xc1c, BIT(0), 0);
+
+static const char * const csi_isp_parents[] = { "pll-periph0-2x",
+ "pll-video0-2x",
+ "pll-video1-2x",
+ "pll-video2-2x",
+ "pll-video3-2x" };
+static SUNXI_CCU_M_WITH_MUX_GATE(csi_isp_clk, "csi-isp",
+ csi_isp_parents, 0xc20,
+ 0, 5, /* M */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+/* Fixed factor clocks */
+static CLK_FIXED_FACTOR_FW_NAME(osc12M_clk, "osc12M", "hosc", 2, 1, 0);
+
+static CLK_FIXED_FACTOR_HW(pll_com_audio_clk, "pll-com-audio",
+ &pll_com_clk.common.hw,
+ 5, 1, CLK_SET_RATE_PARENT);
+
+static CLK_FIXED_FACTOR_HW(pll_periph0_2x_clk, "pll-periph0-2x",
+ &pll_periph0_clk.common.hw,
+ 1, 2, 0);
+
+static CLK_FIXED_FACTOR_HW(pll_periph1_2x_clk, "pll-periph1-2x",
+ &pll_periph1_clk.common.hw,
+ 1, 2, 0);
+
+static const struct clk_hw *pll_video0_parents[] = {
+ &pll_video0_clk.common.hw
+};
+static CLK_FIXED_FACTOR_HWS(pll_video0_4x_clk, "pll-video0-4x",
+ pll_video0_parents,
+ 1, 4, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR_HWS(pll_video0_2x_clk, "pll-video0-2x",
+ pll_video0_parents,
+ 1, 2, CLK_SET_RATE_PARENT);
+
+static const struct clk_hw *pll_video1_parents[] = {
+ &pll_video1_clk.common.hw
+};
+static CLK_FIXED_FACTOR_HWS(pll_video1_4x_clk, "pll-video1-4x",
+ pll_video1_parents,
+ 1, 4, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR_HWS(pll_video1_2x_clk, "pll-video1-2x",
+ pll_video1_parents,
+ 1, 2, CLK_SET_RATE_PARENT);
+
+static const struct clk_hw *pll_video2_parents[] = {
+ &pll_video2_clk.common.hw
+};
+static CLK_FIXED_FACTOR_HWS(pll_video2_4x_clk, "pll-video2-4x",
+ pll_video2_parents,
+ 1, 4, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR_HWS(pll_video2_2x_clk, "pll-video2-2x",
+ pll_video2_parents,
+ 1, 2, CLK_SET_RATE_PARENT);
+
+static const struct clk_hw *pll_video3_parents[] = {
+ &pll_video3_clk.common.hw
+};
+static CLK_FIXED_FACTOR_HWS(pll_video3_4x_clk, "pll-video3-4x",
+ pll_video3_parents,
+ 1, 4, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR_HWS(pll_video3_2x_clk, "pll-video3-2x",
+ pll_video3_parents,
+ 1, 2, CLK_SET_RATE_PARENT);
+
+static struct ccu_common *sun50i_a100_ccu_clks[] = {
+ &pll_cpux_clk.common,
+ &pll_ddr0_clk.common,
+ &pll_periph0_clk.common,
+ &pll_periph1_clk.common,
+ &pll_gpu_clk.common,
+ &pll_video0_clk.common,
+ &pll_video1_clk.common,
+ &pll_video2_clk.common,
+ &pll_video3_clk.common,
+ &pll_ve_clk.common,
+ &pll_com_clk.common,
+ &pll_audio_clk.common,
+ &cpux_clk.common,
+ &axi_clk.common,
+ &cpux_apb_clk.common,
+ &psi_ahb1_ahb2_clk.common,
+ &ahb3_clk.common,
+ &apb1_clk.common,
+ &apb2_clk.common,
+ &mbus_clk.common,
+ &de_clk.common,
+ &bus_de_clk.common,
+ &g2d_clk.common,
+ &bus_g2d_clk.common,
+ &gpu_clk.common,
+ &bus_gpu_clk.common,
+ &ce_clk.common,
+ &bus_ce_clk.common,
+ &ve_clk.common,
+ &bus_ve_clk.common,
+ &bus_dma_clk.common,
+ &bus_msgbox_clk.common,
+ &bus_spinlock_clk.common,
+ &bus_hstimer_clk.common,
+ &avs_clk.common,
+ &bus_dbg_clk.common,
+ &bus_psi_clk.common,
+ &bus_pwm_clk.common,
+ &bus_iommu_clk.common,
+ &mbus_dma_clk.common,
+ &mbus_ve_clk.common,
+ &mbus_ce_clk.common,
+ &mbus_nand_clk.common,
+ &mbus_csi_clk.common,
+ &mbus_isp_clk.common,
+ &mbus_g2d_clk.common,
+ &bus_dram_clk.common,
+ &nand0_clk.common,
+ &nand1_clk.common,
+ &bus_nand_clk.common,
+ &mmc0_clk.common,
+ &mmc1_clk.common,
+ &mmc2_clk.common,
+ &bus_mmc0_clk.common,
+ &bus_mmc1_clk.common,
+ &bus_mmc2_clk.common,
+ &bus_uart0_clk.common,
+ &bus_uart1_clk.common,
+ &bus_uart2_clk.common,
+ &bus_uart3_clk.common,
+ &bus_uart4_clk.common,
+ &bus_i2c0_clk.common,
+ &bus_i2c1_clk.common,
+ &bus_i2c2_clk.common,
+ &bus_i2c3_clk.common,
+ &spi0_clk.common,
+ &spi1_clk.common,
+ &spi2_clk.common,
+ &bus_spi0_clk.common,
+ &bus_spi1_clk.common,
+ &bus_spi2_clk.common,
+ &emac_25m_clk.common,
+ &bus_emac_clk.common,
+ &ir_rx_clk.common,
+ &bus_ir_rx_clk.common,
+ &ir_tx_clk.common,
+ &bus_ir_tx_clk.common,
+ &bus_gpadc_clk.common,
+ &bus_ths_clk.common,
+ &i2s0_clk.common,
+ &i2s1_clk.common,
+ &i2s2_clk.common,
+ &i2s3_clk.common,
+ &bus_i2s0_clk.common,
+ &bus_i2s1_clk.common,
+ &bus_i2s2_clk.common,
+ &bus_i2s3_clk.common,
+ &spdif_clk.common,
+ &bus_spdif_clk.common,
+ &dmic_clk.common,
+ &bus_dmic_clk.common,
+ &audio_codec_dac_clk.common,
+ &audio_codec_adc_clk.common,
+ &audio_codec_4x_clk.common,
+ &bus_audio_codec_clk.common,
+ &usb_ohci0_clk.common,
+ &usb_phy0_clk.common,
+ &usb_ohci1_clk.common,
+ &usb_phy1_clk.common,
+ &bus_ohci0_clk.common,
+ &bus_ohci1_clk.common,
+ &bus_ehci0_clk.common,
+ &bus_ehci1_clk.common,
+ &bus_otg_clk.common,
+ &bus_lradc_clk.common,
+ &bus_dpss_top0_clk.common,
+ &bus_dpss_top1_clk.common,
+ &mipi_dsi_clk.common,
+ &bus_mipi_dsi_clk.common,
+ &tcon_lcd_clk.common,
+ &bus_tcon_lcd_clk.common,
+ &ledc_clk.common,
+ &bus_ledc_clk.common,
+ &csi_top_clk.common,
+ &csi0_mclk_clk.common,
+ &csi1_mclk_clk.common,
+ &bus_csi_clk.common,
+ &csi_isp_clk.common,
+};
+
+static struct clk_hw_onecell_data sun50i_a100_hw_clks = {
+ .hws = {
+ [CLK_OSC12M] = &osc12M_clk.hw,
+ [CLK_PLL_CPUX] = &pll_cpux_clk.common.hw,
+ [CLK_PLL_DDR0] = &pll_ddr0_clk.common.hw,
+ [CLK_PLL_PERIPH0] = &pll_periph0_clk.common.hw,
+ [CLK_PLL_PERIPH0_2X] = &pll_periph0_2x_clk.hw,
+ [CLK_PLL_PERIPH1] = &pll_periph1_clk.common.hw,
+ [CLK_PLL_PERIPH1_2X] = &pll_periph1_2x_clk.hw,
+ [CLK_PLL_GPU] = &pll_gpu_clk.common.hw,
+ [CLK_PLL_VIDEO0] = &pll_video0_clk.common.hw,
+ [CLK_PLL_VIDEO0_2X] = &pll_video0_2x_clk.hw,
+ [CLK_PLL_VIDEO0_4X] = &pll_video0_4x_clk.hw,
+ [CLK_PLL_VIDEO1] = &pll_video1_clk.common.hw,
+ [CLK_PLL_VIDEO1_2X] = &pll_video1_2x_clk.hw,
+ [CLK_PLL_VIDEO1_4X] = &pll_video1_4x_clk.hw,
+ [CLK_PLL_VIDEO2] = &pll_video2_clk.common.hw,
+ [CLK_PLL_VIDEO2_2X] = &pll_video2_2x_clk.hw,
+ [CLK_PLL_VIDEO2_4X] = &pll_video2_4x_clk.hw,
+ [CLK_PLL_VIDEO3] = &pll_video3_clk.common.hw,
+ [CLK_PLL_VIDEO3_2X] = &pll_video3_2x_clk.hw,
+ [CLK_PLL_VIDEO3_4X] = &pll_video3_4x_clk.hw,
+ [CLK_PLL_VE] = &pll_ve_clk.common.hw,
+ [CLK_PLL_COM] = &pll_com_clk.common.hw,
+ [CLK_PLL_COM_AUDIO] = &pll_com_audio_clk.hw,
+ [CLK_PLL_AUDIO] = &pll_audio_clk.common.hw,
+ [CLK_CPUX] = &cpux_clk.common.hw,
+ [CLK_AXI] = &axi_clk.common.hw,
+ [CLK_CPUX_APB] = &cpux_apb_clk.common.hw,
+ [CLK_PSI_AHB1_AHB2] = &psi_ahb1_ahb2_clk.common.hw,
+ [CLK_AHB3] = &ahb3_clk.common.hw,
+ [CLK_APB1] = &apb1_clk.common.hw,
+ [CLK_APB2] = &apb2_clk.common.hw,
+ [CLK_MBUS] = &mbus_clk.common.hw,
+ [CLK_DE] = &de_clk.common.hw,
+ [CLK_BUS_DE] = &bus_de_clk.common.hw,
+ [CLK_G2D] = &g2d_clk.common.hw,
+ [CLK_BUS_G2D] = &bus_g2d_clk.common.hw,
+ [CLK_GPU] = &gpu_clk.common.hw,
+ [CLK_BUS_GPU] = &bus_gpu_clk.common.hw,
+ [CLK_CE] = &ce_clk.common.hw,
+ [CLK_BUS_CE] = &bus_ce_clk.common.hw,
+ [CLK_VE] = &ve_clk.common.hw,
+ [CLK_BUS_VE] = &bus_ve_clk.common.hw,
+ [CLK_BUS_DMA] = &bus_dma_clk.common.hw,
+ [CLK_BUS_MSGBOX] = &bus_msgbox_clk.common.hw,
+ [CLK_BUS_SPINLOCK] = &bus_spinlock_clk.common.hw,
+ [CLK_BUS_HSTIMER] = &bus_hstimer_clk.common.hw,
+ [CLK_AVS] = &avs_clk.common.hw,
+ [CLK_BUS_DBG] = &bus_dbg_clk.common.hw,
+ [CLK_BUS_PSI] = &bus_psi_clk.common.hw,
+ [CLK_BUS_PWM] = &bus_pwm_clk.common.hw,
+ [CLK_BUS_IOMMU] = &bus_iommu_clk.common.hw,
+ [CLK_MBUS_DMA] = &mbus_dma_clk.common.hw,
+ [CLK_MBUS_VE] = &mbus_ve_clk.common.hw,
+ [CLK_MBUS_CE] = &mbus_ce_clk.common.hw,
+ [CLK_MBUS_NAND] = &mbus_nand_clk.common.hw,
+ [CLK_MBUS_CSI] = &mbus_csi_clk.common.hw,
+ [CLK_MBUS_ISP] = &mbus_isp_clk.common.hw,
+ [CLK_MBUS_G2D] = &mbus_g2d_clk.common.hw,
+ [CLK_BUS_DRAM] = &bus_dram_clk.common.hw,
+ [CLK_NAND0] = &nand0_clk.common.hw,
+ [CLK_NAND1] = &nand1_clk.common.hw,
+ [CLK_BUS_NAND] = &bus_nand_clk.common.hw,
+ [CLK_MMC0] = &mmc0_clk.common.hw,
+ [CLK_MMC1] = &mmc1_clk.common.hw,
+ [CLK_MMC2] = &mmc2_clk.common.hw,
+ [CLK_BUS_MMC0] = &bus_mmc0_clk.common.hw,
+ [CLK_BUS_MMC1] = &bus_mmc1_clk.common.hw,
+ [CLK_BUS_MMC2] = &bus_mmc2_clk.common.hw,
+ [CLK_BUS_UART0] = &bus_uart0_clk.common.hw,
+ [CLK_BUS_UART1] = &bus_uart1_clk.common.hw,
+ [CLK_BUS_UART2] = &bus_uart2_clk.common.hw,
+ [CLK_BUS_UART3] = &bus_uart3_clk.common.hw,
+ [CLK_BUS_UART4] = &bus_uart4_clk.common.hw,
+ [CLK_BUS_I2C0] = &bus_i2c0_clk.common.hw,
+ [CLK_BUS_I2C1] = &bus_i2c1_clk.common.hw,
+ [CLK_BUS_I2C2] = &bus_i2c2_clk.common.hw,
+ [CLK_BUS_I2C3] = &bus_i2c3_clk.common.hw,
+ [CLK_SPI0] = &spi0_clk.common.hw,
+ [CLK_SPI1] = &spi1_clk.common.hw,
+ [CLK_SPI2] = &spi2_clk.common.hw,
+ [CLK_BUS_SPI0] = &bus_spi0_clk.common.hw,
+ [CLK_BUS_SPI1] = &bus_spi1_clk.common.hw,
+ [CLK_BUS_SPI2] = &bus_spi2_clk.common.hw,
+ [CLK_EMAC_25M] = &emac_25m_clk.common.hw,
+ [CLK_BUS_EMAC] = &bus_emac_clk.common.hw,
+ [CLK_IR_RX] = &ir_rx_clk.common.hw,
+ [CLK_BUS_IR_RX] = &bus_ir_rx_clk.common.hw,
+ [CLK_IR_TX] = &ir_tx_clk.common.hw,
+ [CLK_BUS_IR_TX] = &bus_ir_tx_clk.common.hw,
+ [CLK_BUS_GPADC] = &bus_gpadc_clk.common.hw,
+ [CLK_BUS_THS] = &bus_ths_clk.common.hw,
+ [CLK_I2S0] = &i2s0_clk.common.hw,
+ [CLK_I2S1] = &i2s1_clk.common.hw,
+ [CLK_I2S2] = &i2s2_clk.common.hw,
+ [CLK_I2S3] = &i2s3_clk.common.hw,
+ [CLK_BUS_I2S0] = &bus_i2s0_clk.common.hw,
+ [CLK_BUS_I2S1] = &bus_i2s1_clk.common.hw,
+ [CLK_BUS_I2S2] = &bus_i2s2_clk.common.hw,
+ [CLK_BUS_I2S3] = &bus_i2s3_clk.common.hw,
+ [CLK_SPDIF] = &spdif_clk.common.hw,
+ [CLK_BUS_SPDIF] = &bus_spdif_clk.common.hw,
+ [CLK_DMIC] = &dmic_clk.common.hw,
+ [CLK_BUS_DMIC] = &bus_dmic_clk.common.hw,
+ [CLK_AUDIO_DAC] = &audio_codec_dac_clk.common.hw,
+ [CLK_AUDIO_ADC] = &audio_codec_adc_clk.common.hw,
+ [CLK_AUDIO_4X] = &audio_codec_4x_clk.common.hw,
+ [CLK_BUS_AUDIO_CODEC] = &bus_audio_codec_clk.common.hw,
+ [CLK_USB_OHCI0] = &usb_ohci0_clk.common.hw,
+ [CLK_USB_PHY0] = &usb_phy0_clk.common.hw,
+ [CLK_USB_OHCI1] = &usb_ohci1_clk.common.hw,
+ [CLK_USB_PHY1] = &usb_phy1_clk.common.hw,
+ [CLK_BUS_OHCI0] = &bus_ohci0_clk.common.hw,
+ [CLK_BUS_OHCI1] = &bus_ohci1_clk.common.hw,
+ [CLK_BUS_EHCI0] = &bus_ehci0_clk.common.hw,
+ [CLK_BUS_EHCI1] = &bus_ehci1_clk.common.hw,
+ [CLK_BUS_OTG] = &bus_otg_clk.common.hw,
+ [CLK_BUS_LRADC] = &bus_lradc_clk.common.hw,
+ [CLK_BUS_DPSS_TOP0] = &bus_dpss_top0_clk.common.hw,
+ [CLK_BUS_DPSS_TOP1] = &bus_dpss_top1_clk.common.hw,
+ [CLK_MIPI_DSI] = &mipi_dsi_clk.common.hw,
+ [CLK_BUS_MIPI_DSI] = &bus_mipi_dsi_clk.common.hw,
+ [CLK_TCON_LCD] = &tcon_lcd_clk.common.hw,
+ [CLK_BUS_TCON_LCD] = &bus_tcon_lcd_clk.common.hw,
+ [CLK_LEDC] = &ledc_clk.common.hw,
+ [CLK_BUS_LEDC] = &bus_ledc_clk.common.hw,
+ [CLK_CSI_TOP] = &csi_top_clk.common.hw,
+ [CLK_CSI0_MCLK] = &csi0_mclk_clk.common.hw,
+ [CLK_CSI1_MCLK] = &csi1_mclk_clk.common.hw,
+ [CLK_BUS_CSI] = &bus_csi_clk.common.hw,
+ [CLK_CSI_ISP] = &csi_isp_clk.common.hw,
+ },
+ .num = CLK_NUMBER,
+};
+
+static struct ccu_reset_map sun50i_a100_ccu_resets[] = {
+ [RST_MBUS] = { 0x540, BIT(30) },
+
+ [RST_BUS_DE] = { 0x60c, BIT(16) },
+ [RST_BUS_G2D] = { 0x63c, BIT(16) },
+ [RST_BUS_GPU] = { 0x67c, BIT(16) },
+ [RST_BUS_CE] = { 0x68c, BIT(16) },
+ [RST_BUS_VE] = { 0x69c, BIT(16) },
+ [RST_BUS_DMA] = { 0x70c, BIT(16) },
+ [RST_BUS_MSGBOX] = { 0x71c, BIT(16) },
+ [RST_BUS_SPINLOCK] = { 0x72c, BIT(16) },
+ [RST_BUS_HSTIMER] = { 0x73c, BIT(16) },
+ [RST_BUS_DBG] = { 0x78c, BIT(16) },
+ [RST_BUS_PSI] = { 0x79c, BIT(16) },
+ [RST_BUS_PWM] = { 0x7ac, BIT(16) },
+ [RST_BUS_DRAM] = { 0x80c, BIT(16) },
+ [RST_BUS_NAND] = { 0x82c, BIT(16) },
+ [RST_BUS_MMC0] = { 0x84c, BIT(16) },
+ [RST_BUS_MMC1] = { 0x84c, BIT(17) },
+ [RST_BUS_MMC2] = { 0x84c, BIT(18) },
+ [RST_BUS_UART0] = { 0x90c, BIT(16) },
+ [RST_BUS_UART1] = { 0x90c, BIT(17) },
+ [RST_BUS_UART2] = { 0x90c, BIT(18) },
+ [RST_BUS_UART3] = { 0x90c, BIT(19) },
+ [RST_BUS_UART4] = { 0x90c, BIT(20) },
+ [RST_BUS_I2C0] = { 0x91c, BIT(16) },
+ [RST_BUS_I2C1] = { 0x91c, BIT(17) },
+ [RST_BUS_I2C2] = { 0x91c, BIT(18) },
+ [RST_BUS_I2C3] = { 0x91c, BIT(19) },
+ [RST_BUS_SPI0] = { 0x96c, BIT(16) },
+ [RST_BUS_SPI1] = { 0x96c, BIT(17) },
+ [RST_BUS_SPI2] = { 0x96c, BIT(18) },
+ [RST_BUS_EMAC] = { 0x97c, BIT(16) },
+ [RST_BUS_IR_RX] = { 0x99c, BIT(16) },
+ [RST_BUS_IR_TX] = { 0x9cc, BIT(16) },
+ [RST_BUS_GPADC] = { 0x9ec, BIT(16) },
+ [RST_BUS_THS] = { 0x9fc, BIT(16) },
+ [RST_BUS_I2S0] = { 0xa20, BIT(16) },
+ [RST_BUS_I2S1] = { 0xa20, BIT(17) },
+ [RST_BUS_I2S2] = { 0xa20, BIT(18) },
+ [RST_BUS_I2S3] = { 0xa20, BIT(19) },
+ [RST_BUS_SPDIF] = { 0xa2c, BIT(16) },
+ [RST_BUS_DMIC] = { 0xa4c, BIT(16) },
+ [RST_BUS_AUDIO_CODEC] = { 0xa5c, BIT(16) },
+
+ [RST_USB_PHY0] = { 0xa70, BIT(30) },
+ [RST_USB_PHY1] = { 0xa74, BIT(30) },
+
+ [RST_BUS_OHCI0] = { 0xa8c, BIT(16) },
+ [RST_BUS_OHCI1] = { 0xa8c, BIT(17) },
+ [RST_BUS_EHCI0] = { 0xa8c, BIT(20) },
+ [RST_BUS_EHCI1] = { 0xa8c, BIT(21) },
+ [RST_BUS_OTG] = { 0xa8c, BIT(24) },
+
+ [RST_BUS_LRADC] = { 0xa9c, BIT(16) },
+ [RST_BUS_DPSS_TOP0] = { 0xabc, BIT(16) },
+ [RST_BUS_DPSS_TOP1] = { 0xacc, BIT(16) },
+ [RST_BUS_MIPI_DSI] = { 0xb4c, BIT(16) },
+ [RST_BUS_TCON_LCD] = { 0xb7c, BIT(16) },
+ [RST_BUS_LVDS] = { 0xbac, BIT(16) },
+ [RST_BUS_LEDC] = { 0xbfc, BIT(16) },
+ [RST_BUS_CSI] = { 0xc1c, BIT(16) },
+ [RST_BUS_CSI_ISP] = { 0xc2c, BIT(16) },
+};
+
+static const struct sunxi_ccu_desc sun50i_a100_ccu_desc = {
+ .ccu_clks = sun50i_a100_ccu_clks,
+ .num_ccu_clks = ARRAY_SIZE(sun50i_a100_ccu_clks),
+
+ .hw_clks = &sun50i_a100_hw_clks,
+
+ .resets = sun50i_a100_ccu_resets,
+ .num_resets = ARRAY_SIZE(sun50i_a100_ccu_resets),
+};
+
+static const u32 sun50i_a100_pll_regs[] = {
+ SUN50I_A100_PLL_CPUX_REG,
+ SUN50I_A100_PLL_DDR0_REG,
+ SUN50I_A100_PLL_PERIPH0_REG,
+ SUN50I_A100_PLL_PERIPH1_REG,
+ SUN50I_A100_PLL_GPU_REG,
+ SUN50I_A100_PLL_VIDEO0_REG,
+ SUN50I_A100_PLL_VIDEO1_REG,
+ SUN50I_A100_PLL_VIDEO2_REG,
+ SUN50I_A100_PLL_VIDEO3_REG,
+ SUN50I_A100_PLL_VE_REG,
+ SUN50I_A100_PLL_COM_REG,
+ SUN50I_A100_PLL_AUDIO_REG,
+};
+
+static const u32 sun50i_a100_pll_video_regs[] = {
+ SUN50I_A100_PLL_VIDEO0_REG,
+ SUN50I_A100_PLL_VIDEO1_REG,
+ SUN50I_A100_PLL_VIDEO2_REG,
+ SUN50I_A100_PLL_VIDEO3_REG,
+};
+
+static const u32 sun50i_a100_usb2_clk_regs[] = {
+ SUN50I_A100_USB0_CLK_REG,
+ SUN50I_A100_USB1_CLK_REG,
+};
+
+static struct ccu_pll_nb sun50i_a100_pll_cpu_nb = {
+ .common = &pll_cpux_clk.common,
+ /* copy from pll_cpux_clk */
+ .enable = BIT(27),
+ .lock = BIT(28),
+};
+
+static struct ccu_mux_nb sun50i_a100_cpu_nb = {
+ .common = &cpux_clk.common,
+ .cm = &cpux_clk.mux,
+ .delay_us = 1,
+ .bypass_index = 4, /* index of pll periph0 */
+};
+
+static int sun50i_a100_ccu_probe(struct platform_device *pdev)
+{
+ void __iomem *reg;
+ u32 val;
+ int i, ret;
+
+ reg = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(reg))
+ return PTR_ERR(reg);
+
+ /*
+ * Enable lock and enable bits on all PLLs.
+ *
+ * Due to the current design, multiple PLLs share one power switch,
+ * so switching PLL is easy to cause stability problems.
+ * When initializing, we enable them by default. When disable,
+ * we only turn off the output of PLL.
+ */
+ for (i = 0; i < ARRAY_SIZE(sun50i_a100_pll_regs); i++) {
+ val = readl(reg + sun50i_a100_pll_regs[i]);
+ val |= SUN50I_A100_PLL_LOCK_ENABLE | SUN50I_A100_PLL_ENABLE;
+ writel(val, reg + sun50i_a100_pll_regs[i]);
+ }
+
+ /*
+ * In order to pass the EMI certification, the SDM function of
+ * the peripheral 1 bus is enabled, and the frequency is still
+ * calculated using the previous division factor.
+ */
+ writel(SUN50I_A100_PLL_PERIPH1_PATTERN0,
+ reg + SUN50I_A100_PLL_PERIPH1_PATTERN0_REG);
+
+ val = readl(reg + SUN50I_A100_PLL_PERIPH1_REG);
+ val |= SUN50I_A100_PLL_SDM_ENABLE;
+ writel(val, reg + SUN50I_A100_PLL_PERIPH1_REG);
+
+ /*
+ * Force the output divider of video PLLs to 0.
+ *
+ * See the comment before pll-video0 definition for the reason.
+ */
+ for (i = 0; i < ARRAY_SIZE(sun50i_a100_pll_video_regs); i++) {
+ val = readl(reg + sun50i_a100_pll_video_regs[i]);
+ val &= ~BIT(0);
+ writel(val, reg + sun50i_a100_pll_video_regs[i]);
+ }
+
+ /*
+ * Enforce m1 = 0, m0 = 1 for Audio PLL
+ *
+ * See the comment before pll-audio definition for the reason.
+ */
+ val = readl(reg + SUN50I_A100_PLL_AUDIO_REG);
+ val &= ~BIT(1);
+ val |= BIT(0);
+ writel(val, reg + SUN50I_A100_PLL_AUDIO_REG);
+
+ /*
+ * Force OHCI 12M clock sources to 00 (12MHz divided from 48MHz)
+ *
+ * This clock mux is still mysterious, and the code just enforces
+ * it to have a valid clock parent.
+ */
+ for (i = 0; i < ARRAY_SIZE(sun50i_a100_usb2_clk_regs); i++) {
+ val = readl(reg + sun50i_a100_usb2_clk_regs[i]);
+ val &= ~GENMASK(25, 24);
+ writel(val, reg + sun50i_a100_usb2_clk_regs[i]);
+ }
+
+ ret = sunxi_ccu_probe(pdev->dev.of_node, reg, &sun50i_a100_ccu_desc);
+ if (ret)
+ return ret;
+
+ /* Gate then ungate PLL CPU after any rate changes */
+ ccu_pll_notifier_register(&sun50i_a100_pll_cpu_nb);
+
+ /* Reparent CPU during PLL CPU rate changes */
+ ccu_mux_notifier_register(pll_cpux_clk.common.hw.clk,
+ &sun50i_a100_cpu_nb);
+
+ return 0;
+}
+
+static const struct of_device_id sun50i_a100_ccu_ids[] = {
+ { .compatible = "allwinner,sun50i-a100-ccu" },
+ { }
+};
+
+static struct platform_driver sun50i_a100_ccu_driver = {
+ .probe = sun50i_a100_ccu_probe,
+ .driver = {
+ .name = "sun50i-a100-ccu",
+ .of_match_table = sun50i_a100_ccu_ids,
+ },
+};
+module_platform_driver(sun50i_a100_ccu_driver);
diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-a100.h b/drivers/clk/sunxi-ng/ccu-sun50i-a100.h
new file mode 100644
index 0000000..a599320
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu-sun50i-a100.h
@@ -0,0 +1,56 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2020 Frank Lee <frank@allwinnertech.com>
+ */
+
+#ifndef _CCU_SUN50I_A100_H_
+#define _CCU_SUN50I_A100_H_
+
+#include <dt-bindings/clock/sun50i-a100-ccu.h>
+#include <dt-bindings/reset/sun50i-a100-ccu.h>
+
+#define CLK_OSC12M 0
+#define CLK_PLL_CPUX 1
+#define CLK_PLL_DDR0 2
+
+/* PLL_PERIPH0 exported for PRCM */
+
+#define CLK_PLL_PERIPH0_2X 4
+#define CLK_PLL_PERIPH1 5
+#define CLK_PLL_PERIPH1_2X 6
+#define CLK_PLL_GPU 7
+#define CLK_PLL_VIDEO0 8
+#define CLK_PLL_VIDEO0_2X 9
+#define CLK_PLL_VIDEO0_4X 10
+#define CLK_PLL_VIDEO1 11
+#define CLK_PLL_VIDEO1_2X 12
+#define CLK_PLL_VIDEO1_4X 13
+#define CLK_PLL_VIDEO2 14
+#define CLK_PLL_VIDEO2_2X 15
+#define CLK_PLL_VIDEO2_4X 16
+#define CLK_PLL_VIDEO3 17
+#define CLK_PLL_VIDEO3_2X 18
+#define CLK_PLL_VIDEO3_4X 19
+#define CLK_PLL_VE 20
+#define CLK_PLL_COM 21
+#define CLK_PLL_COM_AUDIO 22
+#define CLK_PLL_AUDIO 23
+
+/* CPUX clock exported for DVFS */
+
+#define CLK_AXI 25
+#define CLK_CPUX_APB 26
+#define CLK_PSI_AHB1_AHB2 27
+#define CLK_AHB3 28
+
+/* APB1 clock exported for PIO */
+
+#define CLK_APB2 30
+
+/* All module clocks and bus gates are exported except DRAM */
+
+#define CLK_BUS_DRAM 58
+
+#define CLK_NUMBER (CLK_CSI_ISP + 1)
+
+#endif /* _CCU_SUN50I_A100_H_ */
diff --git a/include/dt-bindings/clock/sun50i-a100-ccu.h b/include/dt-bindings/clock/sun50i-a100-ccu.h
new file mode 100644
index 0000000..8cdf563
--- /dev/null
+++ b/include/dt-bindings/clock/sun50i-a100-ccu.h
@@ -0,0 +1,116 @@
+/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */
+/*
+ * Copyright (c) 2020 Frank Lee <frank@allwinnertech.com>
+ */
+
+#ifndef _DT_BINDINGS_CLK_SUN50I_A100_H_
+#define _DT_BINDINGS_CLK_SUN50I_A100_H_
+
+#define CLK_PLL_PERIPH0 3
+
+#define CLK_CPUX 24
+
+#define CLK_APB1 29
+
+#define CLK_MBUS 31
+#define CLK_DE 32
+#define CLK_BUS_DE 33
+#define CLK_G2D 34
+#define CLK_BUS_G2D 35
+#define CLK_GPU 36
+#define CLK_BUS_GPU 37
+#define CLK_CE 38
+#define CLK_BUS_CE 39
+#define CLK_VE 40
+#define CLK_BUS_VE 41
+#define CLK_BUS_DMA 42
+#define CLK_BUS_MSGBOX 43
+#define CLK_BUS_SPINLOCK 44
+#define CLK_BUS_HSTIMER 45
+#define CLK_AVS 46
+#define CLK_BUS_DBG 47
+#define CLK_BUS_PSI 48
+#define CLK_BUS_PWM 49
+#define CLK_BUS_IOMMU 50
+#define CLK_MBUS_DMA 51
+#define CLK_MBUS_VE 52
+#define CLK_MBUS_CE 53
+#define CLK_MBUS_NAND 54
+#define CLK_MBUS_CSI 55
+#define CLK_MBUS_ISP 56
+#define CLK_MBUS_G2D 57
+
+#define CLK_NAND0 59
+#define CLK_NAND1 60
+#define CLK_BUS_NAND 61
+#define CLK_MMC0 62
+#define CLK_MMC1 63
+#define CLK_MMC2 64
+#define CLK_MMC3 65
+#define CLK_BUS_MMC0 66
+#define CLK_BUS_MMC1 67
+#define CLK_BUS_MMC2 68
+#define CLK_BUS_UART0 69
+#define CLK_BUS_UART1 70
+#define CLK_BUS_UART2 71
+#define CLK_BUS_UART3 72
+#define CLK_BUS_UART4 73
+#define CLK_BUS_I2C0 74
+#define CLK_BUS_I2C1 75
+#define CLK_BUS_I2C2 76
+#define CLK_BUS_I2C3 77
+#define CLK_SPI0 78
+#define CLK_SPI1 79
+#define CLK_SPI2 80
+#define CLK_BUS_SPI0 81
+#define CLK_BUS_SPI1 82
+#define CLK_BUS_SPI2 83
+#define CLK_EMAC_25M 84
+#define CLK_BUS_EMAC 85
+#define CLK_IR_RX 86
+#define CLK_BUS_IR_RX 87
+#define CLK_IR_TX 88
+#define CLK_BUS_IR_TX 89
+#define CLK_BUS_GPADC 90
+#define CLK_BUS_THS 91
+#define CLK_I2S0 92
+#define CLK_I2S1 93
+#define CLK_I2S2 94
+#define CLK_I2S3 95
+#define CLK_BUS_I2S0 96
+#define CLK_BUS_I2S1 97
+#define CLK_BUS_I2S2 98
+#define CLK_BUS_I2S3 99
+#define CLK_SPDIF 100
+#define CLK_BUS_SPDIF 101
+#define CLK_DMIC 102
+#define CLK_BUS_DMIC 103
+#define CLK_AUDIO_DAC 104
+#define CLK_AUDIO_ADC 105
+#define CLK_AUDIO_4X 106
+#define CLK_BUS_AUDIO_CODEC 107
+#define CLK_USB_OHCI0 108
+#define CLK_USB_PHY0 109
+#define CLK_USB_OHCI1 110
+#define CLK_USB_PHY1 111
+#define CLK_BUS_OHCI0 112
+#define CLK_BUS_OHCI1 113
+#define CLK_BUS_EHCI0 114
+#define CLK_BUS_EHCI1 115
+#define CLK_BUS_OTG 116
+#define CLK_BUS_LRADC 117
+#define CLK_BUS_DPSS_TOP0 118
+#define CLK_BUS_DPSS_TOP1 119
+#define CLK_MIPI_DSI 120
+#define CLK_BUS_MIPI_DSI 121
+#define CLK_TCON_LCD 122
+#define CLK_BUS_TCON_LCD 123
+#define CLK_LEDC 124
+#define CLK_BUS_LEDC 125
+#define CLK_CSI_TOP 126
+#define CLK_CSI0_MCLK 127
+#define CLK_CSI1_MCLK 128
+#define CLK_BUS_CSI 129
+#define CLK_CSI_ISP 130
+
+#endif /* _DT_BINDINGS_CLK_SUN50I_A100_H_ */
diff --git a/include/dt-bindings/clock/sun50i-a100-r-ccu.h b/include/dt-bindings/clock/sun50i-a100-r-ccu.h
new file mode 100644
index 0000000..8a6cc5c
--- /dev/null
+++ b/include/dt-bindings/clock/sun50i-a100-r-ccu.h
@@ -0,0 +1,23 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2020 Frank Lee <frank@allwinnertech.com>
+ */
+
+#ifndef _DT_BINDINGS_CLK_SUN50I_A100_R_CCU_H_
+#define _DT_BINDINGS_CLK_SUN50I_A100_R_CCU_H_
+
+#define CLK_R_APB1 2
+
+#define CLK_R_APB1_TIMER 4
+#define CLK_R_APB1_TWD 5
+#define CLK_R_APB1_PWM 6
+#define CLK_R_APB1_BUS_PWM 7
+#define CLK_R_APB1_PPU 8
+#define CLK_R_APB2_UART 9
+#define CLK_R_APB2_I2C0 10
+#define CLK_R_APB2_I2C1 11
+#define CLK_R_APB1_IR 12
+#define CLK_R_APB1_BUS_IR 13
+#define CLK_R_AHB_BUS_RTC 14
+
+#endif /* _DT_BINDINGS_CLK_SUN50I_A100_R_CCU_H_ */
diff --git a/include/dt-bindings/reset/sun50i-a100-ccu.h b/include/dt-bindings/reset/sun50i-a100-ccu.h
new file mode 100644
index 0000000..17b8b66
--- /dev/null
+++ b/include/dt-bindings/reset/sun50i-a100-ccu.h
@@ -0,0 +1,68 @@
+/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */
+/*
+ * Copyright (c) 2020 Frank Lee <frank@allwinnertech.com>
+ */
+
+#ifndef _DT_BINDINGS_RESET_SUN50I_A100_H_
+#define _DT_BINDINGS_RESET_SUN50I_A100_H_
+
+#define RST_MBUS 0
+#define RST_BUS_DE 1
+#define RST_BUS_G2D 2
+#define RST_BUS_GPU 3
+#define RST_BUS_CE 4
+#define RST_BUS_VE 5
+#define RST_BUS_DMA 6
+#define RST_BUS_MSGBOX 7
+#define RST_BUS_SPINLOCK 8
+#define RST_BUS_HSTIMER 9
+#define RST_BUS_DBG 10
+#define RST_BUS_PSI 11
+#define RST_BUS_PWM 12
+#define RST_BUS_DRAM 13
+#define RST_BUS_NAND 14
+#define RST_BUS_MMC0 15
+#define RST_BUS_MMC1 16
+#define RST_BUS_MMC2 17
+#define RST_BUS_UART0 18
+#define RST_BUS_UART1 19
+#define RST_BUS_UART2 20
+#define RST_BUS_UART3 21
+#define RST_BUS_UART4 22
+#define RST_BUS_I2C0 23
+#define RST_BUS_I2C1 24
+#define RST_BUS_I2C2 25
+#define RST_BUS_I2C3 26
+#define RST_BUS_SPI0 27
+#define RST_BUS_SPI1 28
+#define RST_BUS_SPI2 29
+#define RST_BUS_EMAC 30
+#define RST_BUS_IR_RX 31
+#define RST_BUS_IR_TX 32
+#define RST_BUS_GPADC 33
+#define RST_BUS_THS 34
+#define RST_BUS_I2S0 35
+#define RST_BUS_I2S1 36
+#define RST_BUS_I2S2 37
+#define RST_BUS_I2S3 38
+#define RST_BUS_SPDIF 39
+#define RST_BUS_DMIC 40
+#define RST_BUS_AUDIO_CODEC 41
+#define RST_USB_PHY0 42
+#define RST_USB_PHY1 43
+#define RST_BUS_OHCI0 44
+#define RST_BUS_OHCI1 45
+#define RST_BUS_EHCI0 46
+#define RST_BUS_EHCI1 47
+#define RST_BUS_OTG 48
+#define RST_BUS_LRADC 49
+#define RST_BUS_DPSS_TOP0 50
+#define RST_BUS_DPSS_TOP1 51
+#define RST_BUS_MIPI_DSI 52
+#define RST_BUS_TCON_LCD 53
+#define RST_BUS_LVDS 54
+#define RST_BUS_LEDC 55
+#define RST_BUS_CSI 56
+#define RST_BUS_CSI_ISP 57
+
+#endif /* _DT_BINDINGS_RESET_SUN50I_A100_H_ */
diff --git a/include/dt-bindings/reset/sun50i-a100-r-ccu.h b/include/dt-bindings/reset/sun50i-a100-r-ccu.h
new file mode 100644
index 0000000..2bf1ed4
--- /dev/null
+++ b/include/dt-bindings/reset/sun50i-a100-r-ccu.h
@@ -0,0 +1,18 @@
+/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */
+/*
+ * Copyright (c) 2020 Frank Lee <frank@allwinnertech.com>
+ */
+
+#ifndef _DT_BINDINGS_RST_SUN50I_A100_R_CCU_H_
+#define _DT_BINDINGS_RST_SUN50I_A100_R_CCU_H_
+
+#define RST_R_APB1_TIMER 0
+#define RST_R_APB1_BUS_PWM 1
+#define RST_R_APB1_PPU 2
+#define RST_R_APB2_UART 3
+#define RST_R_APB2_I2C0 4
+#define RST_R_APB2_I2C1 5
+#define RST_R_APB1_BUS_IR 6
+#define RST_R_AHB_BUS_RTC 7
+
+#endif /* _DT_BINDINGS_RST_SUN50I_A100_R_CCU_H_ */
--
1.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH v3 03/16] dt-bindings: pinctrl: sunxi: Add A100 pinctrl bindings
2020-07-08 7:19 [PATCH v3 00/16] Allwinner A100 Initial support Frank Lee
2020-07-08 7:19 ` [PATCH v3 01/16] dt-bindings: clk: sunxi-ccu: add compatible string for A100 CCU and R-CCU Frank Lee
2020-07-08 7:19 ` [PATCH v3 02/16] clk: sunxi-ng: add support for the Allwinner A100 CCU Frank Lee
@ 2020-07-08 7:19 ` Frank Lee
2020-07-13 23:01 ` Rob Herring
2020-07-08 7:19 ` [PATCH v3 04/16] dt-bindings: pinctrl: sunxi: make gpio banks supplies required Frank Lee
` (7 subsequent siblings)
10 siblings, 1 reply; 22+ messages in thread
From: Frank Lee @ 2020-07-08 7:19 UTC (permalink / raw)
To: robh+dt, mripard, wens, mturquette, sboyd, gregory.clement, tglx,
jason, maz, srinivas.kandagatla, linus.walleij, anarsoul,
tiny.windzz, rui.zhang, daniel.lezcano, amit.kucheria, lee.jones,
p.zabel, clabbe, icenowy, megous, stefan, bage
Cc: devicetree, linux-pm, liyong, linux-kernel, linux-gpio,
huangshuosheng, linux-i2c, Frank Lee, linux-clk,
linux-arm-kernel
Add device tree binding Documentation details for A100 pinctrl driver,
whic has an r pin controller and a pin controller with more irq lines.
Signed-off-by: Frank Lee <frank@allwinnertech.com>
---
.../pinctrl/allwinner,sun4i-a10-pinctrl.yaml | 74 +++++++++++++---------
1 file changed, 44 insertions(+), 30 deletions(-)
diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
index bfefd09..226aba0 100644
--- a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
@@ -48,6 +48,8 @@ properties:
- allwinner,sun9i-a80-r-pinctrl
- allwinner,sun50i-a64-pinctrl
- allwinner,sun50i-a64-r-pinctrl
+ - allwinner,sun50i-a100-pinctrl
+ - allwinner,sun50i-a100-r-pinctrl
- allwinner,sun50i-h5-pinctrl
- allwinner,sun50i-h6-pinctrl
- allwinner,sun50i-h6-r-pinctrl
@@ -59,7 +61,7 @@ properties:
interrupts:
minItems: 1
- maxItems: 5
+ maxItems: 7
description:
One interrupt per external interrupt bank supported on the
controller, sorted by bank number ascending order.
@@ -144,75 +146,87 @@ allOf:
# FIXME: We should have the pin bank supplies here, but not a lot of
# boards are defining it at the moment so it would generate a lot of
# warnings.
-
- if:
properties:
compatible:
enum:
- - allwinner,sun9i-a80-pinctrl
+ - allwinner,sun50i-a100-pinctrl
then:
properties:
interrupts:
- minItems: 5
- maxItems: 5
+ minItems: 7
+ maxItems: 7
else:
if:
properties:
compatible:
enum:
- - allwinner,sun6i-a31-pinctrl
- - allwinner,sun6i-a31s-pinctrl
- - allwinner,sun50i-h6-pinctrl
+ - allwinner,sun9i-a80-pinctrl
then:
properties:
interrupts:
- minItems: 4
- maxItems: 4
+ minItems: 5
+ maxItems: 5
else:
if:
properties:
compatible:
enum:
- - allwinner,sun8i-a23-pinctrl
- - allwinner,sun8i-a83t-pinctrl
- - allwinner,sun50i-a64-pinctrl
- - allwinner,sun50i-h5-pinctrl
- - allwinner,suniv-f1c100s-pinctrl
+ - allwinner,sun6i-a31-pinctrl
+ - allwinner,sun6i-a31s-pinctrl
+ - allwinner,sun50i-h6-pinctrl
then:
properties:
interrupts:
- minItems: 3
- maxItems: 3
+ minItems: 4
+ maxItems: 4
else:
if:
properties:
compatible:
enum:
- - allwinner,sun6i-a31-r-pinctrl
- - allwinner,sun8i-a33-pinctrl
- - allwinner,sun8i-h3-pinctrl
- - allwinner,sun8i-v3-pinctrl
- - allwinner,sun8i-v3s-pinctrl
- - allwinner,sun9i-a80-r-pinctrl
- - allwinner,sun50i-h6-r-pinctrl
+ - allwinner,sun8i-a23-pinctrl
+ - allwinner,sun8i-a83t-pinctrl
+ - allwinner,sun50i-a64-pinctrl
+ - allwinner,sun50i-h5-pinctrl
+ - allwinner,suniv-f1c100s-pinctrl
then:
properties:
interrupts:
- minItems: 2
- maxItems: 2
+ minItems: 3
+ maxItems: 3
else:
- properties:
- interrupts:
- minItems: 1
- maxItems: 1
+ if:
+ properties:
+ compatible:
+ enum:
+ - allwinner,sun6i-a31-r-pinctrl
+ - allwinner,sun8i-a33-pinctrl
+ - allwinner,sun8i-h3-pinctrl
+ - allwinner,sun8i-v3-pinctrl
+ - allwinner,sun8i-v3s-pinctrl
+ - allwinner,sun9i-a80-r-pinctrl
+ - allwinner,sun50i-h6-r-pinctrl
+
+ then:
+ properties:
+ interrupts:
+ minItems: 2
+ maxItems: 2
+
+ else:
+ properties:
+ interrupts:
+ minItems: 1
+ maxItems: 1
additionalProperties: false
--
1.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH v3 04/16] dt-bindings: pinctrl: sunxi: make gpio banks supplies required
2020-07-08 7:19 [PATCH v3 00/16] Allwinner A100 Initial support Frank Lee
` (2 preceding siblings ...)
2020-07-08 7:19 ` [PATCH v3 03/16] dt-bindings: pinctrl: sunxi: Add A100 pinctrl bindings Frank Lee
@ 2020-07-08 7:19 ` Frank Lee
2020-07-09 16:52 ` Rob Herring
` (2 more replies)
2020-07-08 7:19 ` [PATCH v3 05/16] pinctrl: sunxi: add support for the Allwinner A100 pin controller Frank Lee
` (6 subsequent siblings)
10 siblings, 3 replies; 22+ messages in thread
From: Frank Lee @ 2020-07-08 7:19 UTC (permalink / raw)
To: robh+dt, mripard, wens, mturquette, sboyd, gregory.clement, tglx,
jason, maz, srinivas.kandagatla, linus.walleij, anarsoul,
tiny.windzz, rui.zhang, daniel.lezcano, amit.kucheria, lee.jones,
p.zabel, clabbe, icenowy, megous, stefan, bage
Cc: devicetree, linux-pm, liyong, linux-kernel, linux-gpio,
huangshuosheng, linux-i2c, Frank Lee, linux-clk,
linux-arm-kernel
Since we don't really have to care about the existing DT for boards,
it would be great to make the gpio banks supplies required.
Signed-off-by: Frank Lee <frank@allwinnertech.com>
---
.../devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
index 226aba0..c30a7b7 100644
--- a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
@@ -134,6 +134,7 @@ patternProperties:
required:
- "#gpio-cells"
- "#interrupt-cells"
+ - "^vcc-p[a-hlm]-supply$"
- compatible
- reg
- interrupts
--
1.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH v3 05/16] pinctrl: sunxi: add support for the Allwinner A100 pin controller
2020-07-08 7:19 [PATCH v3 00/16] Allwinner A100 Initial support Frank Lee
` (3 preceding siblings ...)
2020-07-08 7:19 ` [PATCH v3 04/16] dt-bindings: pinctrl: sunxi: make gpio banks supplies required Frank Lee
@ 2020-07-08 7:19 ` Frank Lee
2020-07-08 7:19 ` [PATCH v3 06/16] dt-bindings: nvmem: SID: add binding for A100's SID controller Frank Lee
` (5 subsequent siblings)
10 siblings, 0 replies; 22+ messages in thread
From: Frank Lee @ 2020-07-08 7:19 UTC (permalink / raw)
To: robh+dt, mripard, wens, mturquette, sboyd, gregory.clement, tglx,
jason, maz, srinivas.kandagatla, linus.walleij, anarsoul,
tiny.windzz, rui.zhang, daniel.lezcano, amit.kucheria, lee.jones,
p.zabel, clabbe, icenowy, megous, stefan, bage
Cc: devicetree, linux-pm, liyong, linux-kernel, linux-gpio,
huangshuosheng, linux-i2c, Frank Lee, linux-clk,
linux-arm-kernel
This commit introduces support for the pin controller on A100.
Signed-off-by: Frank Lee <frank@allwinnertech.com>
---
drivers/pinctrl/sunxi/Kconfig | 10 +
drivers/pinctrl/sunxi/Makefile | 2 +
drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c | 105 ++++
drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c | 708 ++++++++++++++++++++++++++
4 files changed, 825 insertions(+)
create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c
create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c
diff --git a/drivers/pinctrl/sunxi/Kconfig b/drivers/pinctrl/sunxi/Kconfig
index f7aae20..5932935 100644
--- a/drivers/pinctrl/sunxi/Kconfig
+++ b/drivers/pinctrl/sunxi/Kconfig
@@ -94,6 +94,16 @@ config PINCTRL_SUN50I_A64_R
default ARM64 && ARCH_SUNXI
select PINCTRL_SUNXI
+config PINCTRL_SUN50I_A100
+ bool "Support for the Allwinner A100 PIO"
+ default ARM64 && ARCH_SUNXI
+ select PINCTRL_SUNXI
+
+config PINCTRL_SUN50I_A100_R
+ bool "Support for the Allwinner A100 R-PIO"
+ default ARM64 && ARCH_SUNXI
+ select PINCTRL_SUNXI
+
config PINCTRL_SUN50I_H5
bool "Support for the Allwinner H5 PIO"
default ARM64 && ARCH_SUNXI
diff --git a/drivers/pinctrl/sunxi/Makefile b/drivers/pinctrl/sunxi/Makefile
index fafcdae..8b7ff0d 100644
--- a/drivers/pinctrl/sunxi/Makefile
+++ b/drivers/pinctrl/sunxi/Makefile
@@ -13,6 +13,8 @@ obj-$(CONFIG_PINCTRL_SUN8I_A23_R) += pinctrl-sun8i-a23-r.o
obj-$(CONFIG_PINCTRL_SUN8I_A33) += pinctrl-sun8i-a33.o
obj-$(CONFIG_PINCTRL_SUN50I_A64) += pinctrl-sun50i-a64.o
obj-$(CONFIG_PINCTRL_SUN50I_A64_R) += pinctrl-sun50i-a64-r.o
+obj-$(CONFIG_PINCTRL_SUN50I_A100) += pinctrl-sun50i-a100.o
+obj-$(CONFIG_PINCTRL_SUN50I_A100_R) += pinctrl-sun50i-a100-r.o
obj-$(CONFIG_PINCTRL_SUN8I_A83T) += pinctrl-sun8i-a83t.o
obj-$(CONFIG_PINCTRL_SUN8I_A83T_R) += pinctrl-sun8i-a83t-r.o
obj-$(CONFIG_PINCTRL_SUN8I_H3) += pinctrl-sun8i-h3.o
diff --git a/drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c b/drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c
new file mode 100644
index 0000000..165674f
--- /dev/null
+++ b/drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c
@@ -0,0 +1,105 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2020 Frank Lee <frank@allwinnertech.com>
+ *
+ * Based on:
+ * huangshuosheng <huangshuosheng@allwinnertech.com>
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/platform_device.h>
+
+#include "pinctrl-sunxi.h"
+
+static const struct sunxi_desc_pin a100_r_pins[] = {
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_i2c0"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 0)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_i2c0"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 1)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_uart0"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 2)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_uart0"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 3)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_jtag"), /* MS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 4)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_jtag"), /* CK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 5)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_jtag"), /* DO */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 6)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_jtag"), /* DI */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 7)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_i2c1"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 8)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_i2c1"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 9)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_pwm"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 10)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "s_cir"), /* IN */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 11)),
+};
+
+static const struct sunxi_pinctrl_desc a100_r_pinctrl_data = {
+ .pins = a100_r_pins,
+ .npins = ARRAY_SIZE(a100_r_pins),
+ .pin_base = PL_BASE,
+ .irq_banks = 1,
+};
+
+static int a100_r_pinctrl_probe(struct platform_device *pdev)
+{
+ return sunxi_pinctrl_init(pdev, &a100_r_pinctrl_data);
+}
+
+static const struct of_device_id a100_r_pinctrl_match[] = {
+ { .compatible = "allwinner,sun50i-a100-r-pinctrl", },
+ {}
+};
+MODULE_DEVICE_TABLE(of, a100_r_pinctrl_match);
+
+static struct platform_driver a100_r_pinctrl_driver = {
+ .probe = a100_r_pinctrl_probe,
+ .driver = {
+ .name = "sun50iw10p1-r-pinctrl",
+ .of_match_table = a100_r_pinctrl_match,
+ },
+};
+module_platform_driver(a100_r_pinctrl_driver);
diff --git a/drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c b/drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c
new file mode 100644
index 0000000..c5fe85f
--- /dev/null
+++ b/drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c
@@ -0,0 +1,708 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2020 Frank Lee <frank@allwinnertech.com>
+ *
+ * Based on:
+ * huangshuosheng <huangshuosheng@allwinnertech.com>
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/platform_device.h>
+
+#include "pinctrl-sunxi.h"
+
+static const struct sunxi_desc_pin a100_pins[] = {
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* TX */
+ SUNXI_FUNCTION(0x3, "spi2"), /* CS */
+ SUNXI_FUNCTION(0x4, "jtag"), /* MS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 0)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* RX */
+ SUNXI_FUNCTION(0x3, "spi2"), /* CLK */
+ SUNXI_FUNCTION(0x4, "jtag"), /* CK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 1)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* RTS */
+ SUNXI_FUNCTION(0x3, "spi2"), /* MOSI */
+ SUNXI_FUNCTION(0x4, "jtag"), /* DO */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 2)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* CTS */
+ SUNXI_FUNCTION(0x3, "spi2"), /* MISO */
+ SUNXI_FUNCTION(0x4, "jtag"), /* DI */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 3)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c1"), /* SCK */
+ SUNXI_FUNCTION(0x3, "i2s0"), /* MCLK */
+ SUNXI_FUNCTION(0x4, "jtag_gpu"), /* MS_GPU */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 4)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c1"), /* SDA */
+ SUNXI_FUNCTION(0x3, "i2s0"), /* BCLK */
+ SUNXI_FUNCTION(0x4, "jtag_gpu"), /* CK_GPU */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 5)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "i2s0"), /* LRCK */
+ SUNXI_FUNCTION(0x4, "jtag_gpu"), /* DO_GPU */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 6)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "spdif"), /* DIN */
+ SUNXI_FUNCTION(0x3, "i2s0_dout0"), /* DOUT0 */
+ SUNXI_FUNCTION(0x4, "i2s0_din1"), /* DIN1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 7)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "spdif"), /* DOUT */
+ SUNXI_FUNCTION(0x3, "i2s0_din0"), /* DIN0 */
+ SUNXI_FUNCTION(0x4, "i2s0_dout1"), /* DOUT1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 8)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart0"), /* TX */
+ SUNXI_FUNCTION(0x3, "i2c0"), /* SCK */
+ SUNXI_FUNCTION(0x4, "jtag_gpu"), /* DI_GPU */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 9)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart0"), /* RX */
+ SUNXI_FUNCTION(0x3, "i2c0"), /* SDA */
+ SUNXI_FUNCTION(0x4, "pwm1"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 10)),
+ /* HOLE */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* WE */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* DS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 0)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* ALE */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* RST */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 1)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* CLE */
+ SUNXI_FUNCTION(0x4, "spi0"), /* MOSI */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 2)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* CE1 */
+ SUNXI_FUNCTION(0x4, "spi0"), /* CS0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 3)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* CE0 */
+ SUNXI_FUNCTION(0x4, "spi0"), /* MISO */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 4)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* RE */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 5)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* RB0 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* CMD */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 6)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* RB1 */
+ SUNXI_FUNCTION(0x4, "spi0"), /* CS1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 7)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ7 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D3 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 8)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ6 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D4 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 9)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ5 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 10)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ4 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D5 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 11)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQS */
+ SUNXI_FUNCTION(0x4, "spi0"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 12)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ3 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 13)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ2 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D6 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 14)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ1 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D2 */
+ SUNXI_FUNCTION(0x4, "spi0"), /* WP */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 15)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 16),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ0 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D7 */
+ SUNXI_FUNCTION(0x4, "spi0"), /* HOLD */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 16)),
+ /* HOLE */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D2 */
+ SUNXI_FUNCTION(0x3, "lvds0"), /* D0P */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* DP0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 0)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D3 */
+ SUNXI_FUNCTION(0x3, "lvds0"), /* D0N */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* DM0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 1)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D4 */
+ SUNXI_FUNCTION(0x3, "lvds0"), /* D1P */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* DP1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 2)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D5 */
+ SUNXI_FUNCTION(0x3, "lvds0"), /* D1N */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* DM1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 3)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D6 */
+ SUNXI_FUNCTION(0x3, "lvds0"), /* D2P */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* CKP */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 4)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D7 */
+ SUNXI_FUNCTION(0x3, "lvds0"), /* D2N */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* CKM */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 5)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D10 */
+ SUNXI_FUNCTION(0x3, "lvds0"), /* CKP */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* DP2 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 6)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D11 */
+ SUNXI_FUNCTION(0x3, "lvds0"), /* CKN */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* DM2 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 7)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D12 */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* DP3 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 8)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D13 */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* DM3 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 9)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D14 */
+ SUNXI_FUNCTION(0x4, "spi1"), /* CS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 10)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D15 */
+ SUNXI_FUNCTION(0x4, "spi1"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 11)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D18 */
+ SUNXI_FUNCTION(0x4, "spi1"), /* MOSI */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 12)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D19 */
+ SUNXI_FUNCTION(0x4, "spi1"), /* MISO */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 13)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D20 */
+ SUNXI_FUNCTION(0x4, "uart3"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 14)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D21 */
+ SUNXI_FUNCTION(0x4, "uart3"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 15)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 16),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D22 */
+ SUNXI_FUNCTION(0x4, "uart3"), /* RTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 16)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 17),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D23 */
+ SUNXI_FUNCTION(0x4, "uart3"), /* CTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 17)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 18),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* CLK */
+ SUNXI_FUNCTION(0x4, "uart4"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 18)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 19),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* DE */
+ SUNXI_FUNCTION(0x4, "uart4"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 19)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 20),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* HSYNC */
+ SUNXI_FUNCTION(0x3, "pwm2"),
+ SUNXI_FUNCTION(0x4, "uart4"), /* RTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 20)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 21),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* VSYNC */
+ SUNXI_FUNCTION(0x3, "pwm3"),
+ SUNXI_FUNCTION(0x4, "uart4"), /* CTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 21)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 22),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "pwm1"),
+ SUNXI_FUNCTION(0x4, "i2c0"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 22)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 23),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "pwm0"),
+ SUNXI_FUNCTION(0x4, "i2c0"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 23)),
+ /* HOLE */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* MCLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 0)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c2"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 1)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c2"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 2)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c3"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 3)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c3"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 4)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* MCLK */
+ SUNXI_FUNCTION(0x3, "pll"), /* LOCK_DBG */
+ SUNXI_FUNCTION(0x4, "i2s2"), /* MCLK */
+ SUNXI_FUNCTION(0x5, "ledc"), /* LEDC */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 5)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "bist0"), /* RESULT0 */
+ SUNXI_FUNCTION(0x4, "i2s2"), /* BCLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 6)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* SM_VS */
+ SUNXI_FUNCTION(0x3, "bist0"), /* RESULT1 */
+ SUNXI_FUNCTION(0x4, "i2s2"), /* LRCK */
+ SUNXI_FUNCTION(0x5, "tcon0"), /* TRIG */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 7)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "bist0"), /* RESULT2 */
+ SUNXI_FUNCTION(0x4, "i2s2"), /* DOUT0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 8)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "bist0"), /* RESULT3 */
+ SUNXI_FUNCTION(0x4, "i2s2"), /* DIN0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 9)),
+ /* HOLE */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D1 */
+ SUNXI_FUNCTION(0x3, "jtag"), /* MS1 */
+ SUNXI_FUNCTION(0x4, "jtag_gpu"), /* MS_GPU */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 0)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D0 */
+ SUNXI_FUNCTION(0x3, "jtag"), /* DI1 */
+ SUNXI_FUNCTION(0x4, "jtag_gpu"), /* DI_GPU */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 1)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* CLK */
+ SUNXI_FUNCTION(0x3, "uart0"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 2)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* CMD */
+ SUNXI_FUNCTION(0x3, "jtag"), /* DO */
+ SUNXI_FUNCTION(0x4, "jtag_gpu"), /* DO_GPU */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 3)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D3 */
+ SUNXI_FUNCTION(0x3, "uart0"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 4)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D2 */
+ SUNXI_FUNCTION(0x3, "jtag"), /* CK */
+ SUNXI_FUNCTION(0x4, "jtag_gpu"), /* CK_GPU */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 5)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 6)),
+ /* HOLE */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 0)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* CMD */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 1)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 2)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 3)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D2 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 4)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D3 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 5)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 6)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 7)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* RTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 8)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* CTS */
+ SUNXI_FUNCTION(0x3, "i2s1"), /* MCLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 9)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "i2s1"), /* BCLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 10)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "i2s1"), /* LRCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 11)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "i2s1_dout0"), /* DOUT0 */
+ SUNXI_FUNCTION(0x4, "i2s1_din1"), /* DIN1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 12)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "i2s1_din0"), /* DIN0 */
+ SUNXI_FUNCTION(0x4, "i2s1_dout1"), /* DOUT1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 13)),
+ /* HOLE */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c0"), /* SCK */
+ SUNXI_FUNCTION(0x5, "emac0"), /* RXD1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 0)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c0"), /* SDA */
+ SUNXI_FUNCTION(0x5, "emac0"), /* RXD0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 1)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c1"), /* SCK */
+ SUNXI_FUNCTION(0x5, "emac0"), /* RXCTL */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 2)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c1"), /* SDA */
+ SUNXI_FUNCTION(0x3, "cir0"), /* OUT */
+ SUNXI_FUNCTION(0x5, "emac0"), /* CLKIN */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 3)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart3"), /* TX */
+ SUNXI_FUNCTION(0x3, "spi1"), /* CS */
+ SUNXI_FUNCTION(0x5, "emac0"), /* TXD1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 4)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart3"), /* RX */
+ SUNXI_FUNCTION(0x3, "spi1"), /* CLK */
+ SUNXI_FUNCTION(0x4, "ledc"),
+ SUNXI_FUNCTION(0x5, "emac0"), /* TXD0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 5)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart3"), /* RTS */
+ SUNXI_FUNCTION(0x3, "spi1"), /* MOSI */
+ SUNXI_FUNCTION(0x5, "emac0"), /* TXCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 6)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart3"), /* CTS */
+ SUNXI_FUNCTION(0x3, "spi1"), /* MISO */
+ SUNXI_FUNCTION(0x4, "spdif"), /* OUT */
+ SUNXI_FUNCTION(0x5, "emac0"), /* TXCTL */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 7)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "dmic"), /* CLK */
+ SUNXI_FUNCTION(0x3, "spi2"), /* CS */
+ SUNXI_FUNCTION(0x4, "i2s2"), /* MCLK */
+ SUNXI_FUNCTION(0x5, "i2s2_din2"), /* DIN2 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 8)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "dmic"), /* DATA0 */
+ SUNXI_FUNCTION(0x3, "spi2"), /* CLK */
+ SUNXI_FUNCTION(0x4, "i2s2"), /* BCLK */
+ SUNXI_FUNCTION(0x5, "emac0"), /* MDC */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 9)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "dmic"), /* DATA1 */
+ SUNXI_FUNCTION(0x3, "spi2"), /* MOSI */
+ SUNXI_FUNCTION(0x4, "i2s2"), /* LRCK */
+ SUNXI_FUNCTION(0x5, "emac0"), /* MDIO */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 10)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "dmic"), /* DATA2 */
+ SUNXI_FUNCTION(0x3, "spi2"), /* MISO */
+ SUNXI_FUNCTION(0x4, "i2s2_dout0"), /* DOUT0 */
+ SUNXI_FUNCTION(0x5, "i2s2_din1"), /* DIN1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 11)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "dmic"), /* DATA3 */
+ SUNXI_FUNCTION(0x3, "i2c3"), /* SCK */
+ SUNXI_FUNCTION(0x4, "i2s2_din0"), /* DIN0 */
+ SUNXI_FUNCTION(0x5, "i2s2_dout1"), /* DOUT1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 12)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "i2c3"), /* SCK */
+ SUNXI_FUNCTION(0x4, "i2s3"), /* MCLK */
+ SUNXI_FUNCTION(0x5, "emac0"), /* EPHY */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 13)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x4, "i2s3"), /* BCLK */
+ SUNXI_FUNCTION(0x5, "emac0"), /* RXD3 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 14)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x4, "i2s3"), /* LRCK */
+ SUNXI_FUNCTION(0x5, "emac0"), /* RXD2 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 15)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 16),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "i2s3_dout0"), /* DOUT0 */
+ SUNXI_FUNCTION(0x4, "i2s3_din1"), /* DIN1 */
+ SUNXI_FUNCTION(0x5, "emac0"), /* RXCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 16)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 17),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "i2s3_dout1"), /* DOUT1 */
+ SUNXI_FUNCTION(0x4, "i2s3_din0"), /* DIN0 */
+ SUNXI_FUNCTION(0x5, "emac0"), /* TXD3 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 17)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 18),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "cir0"), /* OUT */
+ SUNXI_FUNCTION(0x3, "i2s3_dout2"), /* DOUT2 */
+ SUNXI_FUNCTION(0x4, "i2s3_din2"), /* DIN2 */
+ SUNXI_FUNCTION(0x5, "emac0"), /* TXD2 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 18)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 19),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "cir0"), /* IN */
+ SUNXI_FUNCTION(0x3, "i2s3_dout3"), /* DOUT3 */
+ SUNXI_FUNCTION(0x4, "i2s3_din3"), /* DIN3 */
+ SUNXI_FUNCTION(0x5, "ledc"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 19)),
+};
+
+static const unsigned int a100_irq_bank_map[] = { 0, 1, 2, 3, 4, 5, 6};
+
+static const struct sunxi_pinctrl_desc a100_pinctrl_data = {
+ .pins = a100_pins,
+ .npins = ARRAY_SIZE(a100_pins),
+ .irq_banks = 7,
+ .irq_bank_map = a100_irq_bank_map,
+ .io_bias_cfg_variant = BIAS_VOLTAGE_PIO_POW_MODE_SEL,
+};
+
+static int a100_pinctrl_probe(struct platform_device *pdev)
+{
+ return sunxi_pinctrl_init(pdev, &a100_pinctrl_data);
+}
+
+static const struct of_device_id a100_pinctrl_match[] = {
+ { .compatible = "allwinner,sun50i-a100-pinctrl", },
+ {}
+};
+MODULE_DEVICE_TABLE(of, a100_pinctrl_match);
+
+static struct platform_driver a100_pinctrl_driver = {
+ .probe = a100_pinctrl_probe,
+ .driver = {
+ .name = "sun50i-a100-pinctrl",
+ .of_match_table = a100_pinctrl_match,
+ },
+};
+module_platform_driver(a100_pinctrl_driver);
--
1.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH v3 06/16] dt-bindings: nvmem: SID: add binding for A100's SID controller
2020-07-08 7:19 [PATCH v3 00/16] Allwinner A100 Initial support Frank Lee
` (4 preceding siblings ...)
2020-07-08 7:19 ` [PATCH v3 05/16] pinctrl: sunxi: add support for the Allwinner A100 pin controller Frank Lee
@ 2020-07-08 7:19 ` Frank Lee
2020-07-09 16:54 ` Rob Herring
2020-07-08 7:19 ` [PATCH v3 07/16] dt-bindings: thermal: sun8i: Add binding for A100's THS controller Frank Lee
` (4 subsequent siblings)
10 siblings, 1 reply; 22+ messages in thread
From: Frank Lee @ 2020-07-08 7:19 UTC (permalink / raw)
To: robh+dt, mripard, wens, mturquette, sboyd, gregory.clement, tglx,
jason, maz, srinivas.kandagatla, linus.walleij, anarsoul,
tiny.windzz, rui.zhang, daniel.lezcano, amit.kucheria, lee.jones,
p.zabel, clabbe, icenowy, megous, stefan, bage
Cc: devicetree, linux-pm, liyong, linux-kernel, linux-gpio,
huangshuosheng, linux-i2c, Frank Lee, linux-clk,
linux-arm-kernel
Add a binding for A100's SID controller.
Signed-off-by: Frank Lee <frank@allwinnertech.com>
---
Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml | 3 +++
1 file changed, 3 insertions(+)
diff --git a/Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml b/Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml
index daf1321..f9d575b 100644
--- a/Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml
+++ b/Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml
@@ -21,6 +21,9 @@ properties:
- allwinner,sun8i-a83t-sid
- allwinner,sun8i-h3-sid
- allwinner,sun50i-a64-sid
+ - items:
+ - const: allwinner,sun50i-a100-sid
+ - const: allwinner,sun50i-a64-sid
- allwinner,sun50i-h5-sid
- allwinner,sun50i-h6-sid
--
1.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH v3 07/16] dt-bindings: thermal: sun8i: Add binding for A100's THS controller
2020-07-08 7:19 [PATCH v3 00/16] Allwinner A100 Initial support Frank Lee
` (5 preceding siblings ...)
2020-07-08 7:19 ` [PATCH v3 06/16] dt-bindings: nvmem: SID: add binding for A100's SID controller Frank Lee
@ 2020-07-08 7:19 ` Frank Lee
2020-07-13 23:02 ` Rob Herring
2020-07-08 7:19 ` [PATCH v3 09/16] thermal: sun8i: Add A100's THS controller support Frank Lee
` (3 subsequent siblings)
10 siblings, 1 reply; 22+ messages in thread
From: Frank Lee @ 2020-07-08 7:19 UTC (permalink / raw)
To: robh+dt, mripard, wens, mturquette, sboyd, gregory.clement, tglx,
jason, maz, srinivas.kandagatla, linus.walleij, anarsoul,
tiny.windzz, rui.zhang, daniel.lezcano, amit.kucheria, lee.jones,
p.zabel, clabbe, icenowy, megous, stefan, bage
Cc: devicetree, linux-pm, liyong, linux-kernel, linux-gpio,
huangshuosheng, linux-i2c, Frank Lee, linux-clk,
linux-arm-kernel
Add a binding for A100's ths controller.
Signed-off-by: Frank Lee <frank@allwinnertech.com>
Reviewed-by: Yangtao Li <tiny.windzz@gmail.com>
---
.../devicetree/bindings/thermal/allwinner,sun8i-a83t-ths.yaml | 6 +++++-
1 file changed, 5 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/thermal/allwinner,sun8i-a83t-ths.yaml b/Documentation/devicetree/bindings/thermal/allwinner,sun8i-a83t-ths.yaml
index 8736926..9d40fc7 100644
--- a/Documentation/devicetree/bindings/thermal/allwinner,sun8i-a83t-ths.yaml
+++ b/Documentation/devicetree/bindings/thermal/allwinner,sun8i-a83t-ths.yaml
@@ -17,6 +17,7 @@ properties:
- allwinner,sun8i-h3-ths
- allwinner,sun8i-r40-ths
- allwinner,sun50i-a64-ths
+ - allwinner,sun50i-a100-ths
- allwinner,sun50i-h5-ths
- allwinner,sun50i-h6-ths
@@ -61,7 +62,9 @@ allOf:
properties:
compatible:
contains:
- const: allwinner,sun50i-h6-ths
+ enum:
+ - allwinner,sun50i-a100-ths
+ - allwinner,sun50i-h6-ths
then:
properties:
@@ -103,6 +106,7 @@ allOf:
- const: allwinner,sun8i-h3-ths
- const: allwinner,sun8i-r40-ths
- const: allwinner,sun50i-a64-ths
+ - const: allwinner,sun50i-a100-ths
- const: allwinner,sun50i-h5-ths
- const: allwinner,sun50i-h6-ths
--
1.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH v3 09/16] thermal: sun8i: Add A100's THS controller support
2020-07-08 7:19 [PATCH v3 00/16] Allwinner A100 Initial support Frank Lee
` (6 preceding siblings ...)
2020-07-08 7:19 ` [PATCH v3 07/16] dt-bindings: thermal: sun8i: Add binding for A100's THS controller Frank Lee
@ 2020-07-08 7:19 ` Frank Lee
2020-07-08 7:19 ` [PATCH v3 10/16] mfd: axp20x: Allow the AXP803 to be probed by I2C Frank Lee
` (2 subsequent siblings)
10 siblings, 0 replies; 22+ messages in thread
From: Frank Lee @ 2020-07-08 7:19 UTC (permalink / raw)
To: robh+dt, mripard, wens, mturquette, sboyd, gregory.clement, tglx,
jason, maz, srinivas.kandagatla, linus.walleij, anarsoul,
tiny.windzz, rui.zhang, daniel.lezcano, amit.kucheria, lee.jones,
p.zabel, clabbe, icenowy, megous, stefan, bage
Cc: devicetree, linux-pm, liyong, linux-kernel, linux-gpio,
huangshuosheng, linux-i2c, Frank Lee, linux-clk,
linux-arm-kernel
This patch add thermal sensor controller support for A100,
which is similar to the previous ones.
Signed-off-by: Frank Lee <frank@allwinnertech.com>
Reviewed-by: Yangtao Li <tiny.windzz@gmail.com>
---
drivers/thermal/sun8i_thermal.c | 14 ++++++++++++++
1 file changed, 14 insertions(+)
diff --git a/drivers/thermal/sun8i_thermal.c b/drivers/thermal/sun8i_thermal.c
index f423d44..f8b1307 100644
--- a/drivers/thermal/sun8i_thermal.c
+++ b/drivers/thermal/sun8i_thermal.c
@@ -590,6 +590,19 @@ static int sun8i_ths_remove(struct platform_device *pdev)
.calc_temp = sun8i_ths_calc_temp,
};
+static const struct ths_thermal_chip sun50i_a100_ths = {
+ .sensor_num = 3,
+ .has_bus_clk_reset = true,
+ .ft_deviation = 8000,
+ .offset = 187744,
+ .scale = 672,
+ .temp_data_base = SUN50I_H6_THS_TEMP_DATA,
+ .calibrate = sun50i_h6_ths_calibrate,
+ .init = sun50i_h6_thermal_init,
+ .irq_ack = sun50i_h6_irq_ack,
+ .calc_temp = sun8i_ths_calc_temp,
+};
+
static const struct ths_thermal_chip sun50i_h5_ths = {
.sensor_num = 2,
.has_mod_clk = true,
@@ -619,6 +632,7 @@ static int sun8i_ths_remove(struct platform_device *pdev)
{ .compatible = "allwinner,sun8i-h3-ths", .data = &sun8i_h3_ths },
{ .compatible = "allwinner,sun8i-r40-ths", .data = &sun8i_r40_ths },
{ .compatible = "allwinner,sun50i-a64-ths", .data = &sun50i_a64_ths },
+ { .compatible = "allwinner,sun50i-a100-ths", .data = &sun50i_a100_ths },
{ .compatible = "allwinner,sun50i-h5-ths", .data = &sun50i_h5_ths },
{ .compatible = "allwinner,sun50i-h6-ths", .data = &sun50i_h6_ths },
{ /* sentinel */ },
--
1.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH v3 10/16] mfd: axp20x: Allow the AXP803 to be probed by I2C
2020-07-08 7:19 [PATCH v3 00/16] Allwinner A100 Initial support Frank Lee
` (7 preceding siblings ...)
2020-07-08 7:19 ` [PATCH v3 09/16] thermal: sun8i: Add A100's THS controller support Frank Lee
@ 2020-07-08 7:19 ` Frank Lee
2020-07-16 15:10 ` Lee Jones
2020-07-08 7:45 ` [PATCH v3 00/16] Allwinner A100 Initial support Corentin Labbe
2020-07-10 14:28 ` Maxime Ripard
10 siblings, 1 reply; 22+ messages in thread
From: Frank Lee @ 2020-07-08 7:19 UTC (permalink / raw)
To: robh+dt, mripard, wens, mturquette, sboyd, gregory.clement, tglx,
jason, maz, srinivas.kandagatla, linus.walleij, anarsoul,
tiny.windzz, rui.zhang, daniel.lezcano, amit.kucheria, lee.jones,
p.zabel, clabbe, icenowy, megous, stefan, bage
Cc: devicetree, linux-pm, liyong, linux-kernel, linux-gpio,
huangshuosheng, linux-i2c, Frank Lee, linux-clk,
linux-arm-kernel
The AXP803 can be used both using the RSB proprietary bus, or a more
traditional I2C bus.
Let's add that possibility.
Signed-off-by: Frank Lee <frank@allwinnertech.com>
---
drivers/mfd/axp20x-i2c.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/drivers/mfd/axp20x-i2c.c b/drivers/mfd/axp20x-i2c.c
index 14f9df7..446a7d0 100644
--- a/drivers/mfd/axp20x-i2c.c
+++ b/drivers/mfd/axp20x-i2c.c
@@ -63,6 +63,7 @@ static int axp20x_i2c_remove(struct i2c_client *i2c)
{ .compatible = "x-powers,axp209", .data = (void *)AXP209_ID },
{ .compatible = "x-powers,axp221", .data = (void *)AXP221_ID },
{ .compatible = "x-powers,axp223", .data = (void *)AXP223_ID },
+ { .compatible = "x-powers,axp803", .data = (void *)AXP803_ID },
{ .compatible = "x-powers,axp806", .data = (void *)AXP806_ID },
{ },
};
@@ -74,6 +75,7 @@ static int axp20x_i2c_remove(struct i2c_client *i2c)
{ "axp209", 0 },
{ "axp221", 0 },
{ "axp223", 0 },
+ { "axp803", 0 },
{ "axp806", 0 },
{ },
};
--
1.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 22+ messages in thread
* Re: [PATCH v3 00/16] Allwinner A100 Initial support
2020-07-08 7:19 [PATCH v3 00/16] Allwinner A100 Initial support Frank Lee
` (8 preceding siblings ...)
2020-07-08 7:19 ` [PATCH v3 10/16] mfd: axp20x: Allow the AXP803 to be probed by I2C Frank Lee
@ 2020-07-08 7:45 ` Corentin Labbe
2020-07-10 14:28 ` Maxime Ripard
10 siblings, 0 replies; 22+ messages in thread
From: Corentin Labbe @ 2020-07-08 7:45 UTC (permalink / raw)
To: Frank Lee
Cc: megous, liyong, tiny.windzz, linus.walleij, srinivas.kandagatla,
linux-i2c, lee.jones, linux-clk, amit.kucheria, stefan, maz,
gregory.clement, daniel.lezcano, anarsoul, wens, huangshuosheng,
clabbe, rui.zhang, mturquette, icenowy, devicetree, jason, bage,
linux-pm, mripard, linux-gpio, robh+dt, tglx, linux-arm-kernel,
sboyd, linux-kernel, p.zabel
On Wed, Jul 08, 2020 at 03:19:26PM +0800, Frank Lee wrote:
> This patch set adds initial support for allwinner a100 soc,
> which is a 64-bit tablet chip.
>
Hello
Does a product already exists with it ? I couldnt found any.
Does a datasheet is availlable ?
Regards
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH v3 04/16] dt-bindings: pinctrl: sunxi: make gpio banks supplies required
2020-07-08 7:19 ` [PATCH v3 04/16] dt-bindings: pinctrl: sunxi: make gpio banks supplies required Frank Lee
@ 2020-07-09 16:52 ` Rob Herring
2020-07-09 16:54 ` Rob Herring
2020-07-09 17:17 ` Ondřej Jirman
2 siblings, 0 replies; 22+ messages in thread
From: Rob Herring @ 2020-07-09 16:52 UTC (permalink / raw)
To: Frank Lee
Cc: megous, liyong, tiny.windzz, linus.walleij, srinivas.kandagatla,
linux-i2c, lee.jones, linux-clk, amit.kucheria, stefan, maz,
gregory.clement, daniel.lezcano, anarsoul, wens, huangshuosheng,
clabbe, rui.zhang, mturquette, icenowy, devicetree, jason, bage,
linux-pm, mripard, linux-gpio, robh+dt, tglx, linux-arm-kernel,
sboyd, linux-kernel, p.zabel
On Wed, 08 Jul 2020 15:19:30 +0800, Frank Lee wrote:
> Since we don't really have to care about the existing DT for boards,
> it would be great to make the gpio banks supplies required.
>
> Signed-off-by: Frank Lee <frank@allwinnertech.com>
> ---
> .../devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml | 1 +
> 1 file changed, 1 insertion(+)
>
My bot found errors running 'make dt_binding_check' on your patch:
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml: required:2: '^vcc-p[a-hlm]-supply$' does not match '^([a-zA-Z#][a-zA-Z0-9,+\\-._@]{0,63}|\\$nodename)$'
Documentation/devicetree/bindings/Makefile:20: recipe for target 'Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.example.dts' failed
make[1]: *** [Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.example.dts] Error 1
make[1]: *** Waiting for unfinished jobs....
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml: ignoring, error in schema: required: 2
warning: no schema found in file: ./Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml: ignoring, error in schema: required: 2
warning: no schema found in file: ./Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
Makefile:1347: recipe for target 'dt_binding_check' failed
make: *** [dt_binding_check] Error 2
See https://patchwork.ozlabs.org/patch/1325057
If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure dt-schema is up to date:
pip3 install git+https://github.com/devicetree-org/dt-schema.git@master --upgrade
Please check and re-submit.
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH v3 04/16] dt-bindings: pinctrl: sunxi: make gpio banks supplies required
2020-07-08 7:19 ` [PATCH v3 04/16] dt-bindings: pinctrl: sunxi: make gpio banks supplies required Frank Lee
2020-07-09 16:52 ` Rob Herring
@ 2020-07-09 16:54 ` Rob Herring
2020-07-09 17:17 ` Ondřej Jirman
2 siblings, 0 replies; 22+ messages in thread
From: Rob Herring @ 2020-07-09 16:54 UTC (permalink / raw)
To: Frank Lee
Cc: megous, liyong, tiny.windzz, linus.walleij, srinivas.kandagatla,
linux-i2c, lee.jones, linux-clk, amit.kucheria, stefan, maz,
gregory.clement, daniel.lezcano, anarsoul, wens, huangshuosheng,
clabbe, rui.zhang, mturquette, icenowy, devicetree, jason, bage,
linux-pm, mripard, linux-gpio, tglx, linux-arm-kernel, sboyd,
linux-kernel, p.zabel
On Wed, Jul 08, 2020 at 03:19:30PM +0800, Frank Lee wrote:
> Since we don't really have to care about the existing DT for boards,
> it would be great to make the gpio banks supplies required.
>
> Signed-off-by: Frank Lee <frank@allwinnertech.com>
> ---
> .../devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml | 1 +
> 1 file changed, 1 insertion(+)
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> index 226aba0..c30a7b7 100644
> --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> @@ -134,6 +134,7 @@ patternProperties:
> required:
> - "#gpio-cells"
> - "#interrupt-cells"
> + - "^vcc-p[a-hlm]-supply$"
Patterns aren't supported here. It's something the json-schema folks
are working on. For now, You have to list out the specific properties.
> - compatible
> - reg
> - interrupts
> --
> 1.9.1
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH v3 06/16] dt-bindings: nvmem: SID: add binding for A100's SID controller
2020-07-08 7:19 ` [PATCH v3 06/16] dt-bindings: nvmem: SID: add binding for A100's SID controller Frank Lee
@ 2020-07-09 16:54 ` Rob Herring
0 siblings, 0 replies; 22+ messages in thread
From: Rob Herring @ 2020-07-09 16:54 UTC (permalink / raw)
To: Frank Lee
Cc: megous, liyong, tiny.windzz, linus.walleij, srinivas.kandagatla,
linux-i2c, lee.jones, linux-clk, amit.kucheria, stefan, maz,
gregory.clement, daniel.lezcano, anarsoul, wens, huangshuosheng,
clabbe, rui.zhang, mturquette, icenowy, devicetree, jason, bage,
linux-pm, mripard, linux-gpio, robh+dt, tglx, linux-arm-kernel,
sboyd, linux-kernel, p.zabel
On Wed, 08 Jul 2020 15:19:32 +0800, Frank Lee wrote:
> Add a binding for A100's SID controller.
>
> Signed-off-by: Frank Lee <frank@allwinnertech.com>
> ---
> Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml | 3 +++
> 1 file changed, 3 insertions(+)
>
My bot found errors running 'make dt_binding_check' on your patch:
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml: properties:compatible:enum:5: {'items': [{'const': 'allwinner,sun50i-a100-sid'}, {'const': 'allwinner,sun50i-a64-sid'}]} is not of type 'string'
Documentation/devicetree/bindings/Makefile:20: recipe for target 'Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.example.dts' failed
make[1]: *** [Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.example.dts] Error 1
make[1]: *** Waiting for unfinished jobs....
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml: ignoring, error in schema: properties: compatible: enum: 5
warning: no schema found in file: ./Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml: ignoring, error in schema: properties: compatible: enum: 5
warning: no schema found in file: ./Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml
Makefile:1347: recipe for target 'dt_binding_check' failed
make: *** [dt_binding_check] Error 2
See https://patchwork.ozlabs.org/patch/1325053
If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure dt-schema is up to date:
pip3 install git+https://github.com/devicetree-org/dt-schema.git@master --upgrade
Please check and re-submit.
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH v3 04/16] dt-bindings: pinctrl: sunxi: make gpio banks supplies required
2020-07-08 7:19 ` [PATCH v3 04/16] dt-bindings: pinctrl: sunxi: make gpio banks supplies required Frank Lee
2020-07-09 16:52 ` Rob Herring
2020-07-09 16:54 ` Rob Herring
@ 2020-07-09 17:17 ` Ondřej Jirman
2020-07-10 12:37 ` Maxime Ripard
2 siblings, 1 reply; 22+ messages in thread
From: Ondřej Jirman @ 2020-07-09 17:17 UTC (permalink / raw)
To: Frank Lee
Cc: liyong, tiny.windzz, linus.walleij, srinivas.kandagatla,
linux-i2c, lee.jones, linux-clk, amit.kucheria, stefan, maz,
gregory.clement, daniel.lezcano, anarsoul, wens, huangshuosheng,
clabbe, rui.zhang, mturquette, icenowy, devicetree, jason, bage,
linux-pm, mripard, linux-gpio, robh+dt, tglx, linux-arm-kernel,
sboyd, linux-kernel, p.zabel
Hello,
On Wed, Jul 08, 2020 at 03:19:30PM +0800, Frank Lee wrote:
> Since we don't really have to care about the existing DT for boards,
> it would be great to make the gpio banks supplies required.
What if the borad doesn't use one of the banks? How would
I describe such a board if defining supplies for all banks
is required?
regards,
o.
> Signed-off-by: Frank Lee <frank@allwinnertech.com>
> ---
> .../devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml | 1 +
> 1 file changed, 1 insertion(+)
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> index 226aba0..c30a7b7 100644
> --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> @@ -134,6 +134,7 @@ patternProperties:
> required:
> - "#gpio-cells"
> - "#interrupt-cells"
> + - "^vcc-p[a-hlm]-supply$"
> - compatible
> - reg
> - interrupts
> --
> 1.9.1
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH v3 04/16] dt-bindings: pinctrl: sunxi: make gpio banks supplies required
2020-07-09 17:17 ` Ondřej Jirman
@ 2020-07-10 12:37 ` Maxime Ripard
0 siblings, 0 replies; 22+ messages in thread
From: Maxime Ripard @ 2020-07-10 12:37 UTC (permalink / raw)
To: Ondřej Jirman, Frank Lee, robh+dt, wens, mturquette, sboyd,
gregory.clement, tglx, jason, maz, srinivas.kandagatla,
linus.walleij, anarsoul, tiny.windzz, rui.zhang, daniel.lezcano,
amit.kucheria, lee.jones, p.zabel, clabbe, icenowy, stefan, bage,
devicetree, linux-pm, liyong, linux-kernel, linux-gpio,
huangshuosheng, linux-i2c, linux-clk, linux-arm-kernel
Hi,
On Thu, Jul 09, 2020 at 07:17:13PM +0200, Ondřej Jirman wrote:
> Hello,
>
> On Wed, Jul 08, 2020 at 03:19:30PM +0800, Frank Lee wrote:
> > Since we don't really have to care about the existing DT for boards,
> > it would be great to make the gpio banks supplies required.
>
> What if the borad doesn't use one of the banks? How would
> I describe such a board if defining supplies for all banks
> is required?
If that case ever comes up, we can always drop the requirement, it's going to be backward
compatible.
Maxime
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH v3 00/16] Allwinner A100 Initial support
2020-07-08 7:19 [PATCH v3 00/16] Allwinner A100 Initial support Frank Lee
` (9 preceding siblings ...)
2020-07-08 7:45 ` [PATCH v3 00/16] Allwinner A100 Initial support Corentin Labbe
@ 2020-07-10 14:28 ` Maxime Ripard
10 siblings, 0 replies; 22+ messages in thread
From: Maxime Ripard @ 2020-07-10 14:28 UTC (permalink / raw)
To: Frank Lee
Cc: megous, liyong, tiny.windzz, linus.walleij, srinivas.kandagatla,
linux-i2c, lee.jones, linux-clk, amit.kucheria, stefan, maz,
gregory.clement, daniel.lezcano, anarsoul, wens, huangshuosheng,
clabbe, rui.zhang, mturquette, icenowy, devicetree, jason, bage,
linux-pm, linux-gpio, robh+dt, tglx, linux-arm-kernel, sboyd,
linux-kernel, p.zabel
Hi,
On Wed, Jul 08, 2020 at 03:19:26PM +0800, Frank Lee wrote:
> This patch set adds initial support for allwinner a100 soc,
> which is a 64-bit tablet chip.
>
> v3:
> -Add pmu and nmi support
> -Add read data mask for calibration
> -Code style
> -Some trivial things in yaml files
>
> v2:
> -Some naming consistency
> -Repair email address
> -Fix mmc clock
> -Don't export system clock
> -Fix checkpatch warning
> -Drop unneeded pin function, convert to jtag_gpu and i2s_x
>
> Frank Lee (16):
> dt-bindings: clk: sunxi-ccu: add compatible string for A100 CCU and
> R-CCU
> clk: sunxi-ng: add support for the Allwinner A100 CCU
> dt-bindings: pinctrl: sunxi: Add A100 pinctrl bindings
> dt-bindings: pinctrl: sunxi: make gpio banks supplies required
> pinctrl: sunxi: add support for the Allwinner A100 pin controller
> dt-bindings: nvmem: SID: add binding for A100's SID controller
> dt-bindings: thermal: sun8i: Add binding for A100's THS controller
> thermal: sun8i: add TEMP_CALIB_MASK for calibration data in
> sun50i_h6_ths_calibrate
> thermal: sun8i: Add A100's THS controller support
> mfd: axp20x: Allow the AXP803 to be probed by I2C
> dt-bindings: irq: sun7i-nmi: fix dt-binding for a80 nmi
> dt-bindings: irq: sun7i-nmi: Add binding for A100's NMI controller
it doesn't look like those patches went through?
> dt-bindings: i2c: mv64xxx: Add compatible for the A100 i2c node.
> arm64: allwinner: A100: add the basical Allwinner A100 DTSI file
> dt-bindings: arm: sunxi: Add Allwinner A100 Perf1 Board bindings
> arm64: allwinner: A100: add support for Allwinner Perf1 board
On a more general topic, which bootloader have you used to test this?
The one from Allwinner's BSP I assume?
Maxime
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH v3 01/16] dt-bindings: clk: sunxi-ccu: add compatible string for A100 CCU and R-CCU
2020-07-08 7:19 ` [PATCH v3 01/16] dt-bindings: clk: sunxi-ccu: add compatible string for A100 CCU and R-CCU Frank Lee
@ 2020-07-13 22:54 ` Rob Herring
2020-07-13 23:33 ` Rob Herring
0 siblings, 1 reply; 22+ messages in thread
From: Rob Herring @ 2020-07-13 22:54 UTC (permalink / raw)
To: Frank Lee
Cc: megous, liyong, tiny.windzz, mturquette, srinivas.kandagatla,
linux-i2c, lee.jones, linux-clk, amit.kucheria, stefan, maz,
gregory.clement, daniel.lezcano, anarsoul, wens, huangshuosheng,
clabbe, rui.zhang, linus.walleij, icenowy, devicetree, jason,
bage, linux-pm, mripard, linux-gpio, robh+dt, tglx,
linux-arm-kernel, sboyd, linux-kernel, p.zabel
On Wed, 08 Jul 2020 15:19:27 +0800, Frank Lee wrote:
> This patch adds binding to a100's ccu clock and r-ccu clock.
>
> Signed-off-by: Frank Lee <frank@allwinnertech.com>
> ---
> .../devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml | 7 ++++++-
> 1 file changed, 6 insertions(+), 1 deletion(-)
>
Reviewed-by: Rob Herring <robh@kernel.org>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH v3 03/16] dt-bindings: pinctrl: sunxi: Add A100 pinctrl bindings
2020-07-08 7:19 ` [PATCH v3 03/16] dt-bindings: pinctrl: sunxi: Add A100 pinctrl bindings Frank Lee
@ 2020-07-13 23:01 ` Rob Herring
0 siblings, 0 replies; 22+ messages in thread
From: Rob Herring @ 2020-07-13 23:01 UTC (permalink / raw)
To: Frank Lee
Cc: megous, liyong, tiny.windzz, linus.walleij, srinivas.kandagatla,
linux-i2c, lee.jones, linux-clk, amit.kucheria, stefan, maz,
gregory.clement, daniel.lezcano, anarsoul, wens, huangshuosheng,
clabbe, rui.zhang, mturquette, icenowy, devicetree, jason, bage,
linux-pm, mripard, linux-gpio, tglx, linux-arm-kernel, sboyd,
linux-kernel, p.zabel
On Wed, Jul 08, 2020 at 03:19:29PM +0800, Frank Lee wrote:
> Add device tree binding Documentation details for A100 pinctrl driver,
> whic has an r pin controller and a pin controller with more irq lines.
s/whic/which/
'an r pin controller'?
>
> Signed-off-by: Frank Lee <frank@allwinnertech.com>
> ---
> .../pinctrl/allwinner,sun4i-a10-pinctrl.yaml | 74 +++++++++++++---------
> 1 file changed, 44 insertions(+), 30 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> index bfefd09..226aba0 100644
> --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> @@ -48,6 +48,8 @@ properties:
> - allwinner,sun9i-a80-r-pinctrl
> - allwinner,sun50i-a64-pinctrl
> - allwinner,sun50i-a64-r-pinctrl
> + - allwinner,sun50i-a100-pinctrl
> + - allwinner,sun50i-a100-r-pinctrl
> - allwinner,sun50i-h5-pinctrl
> - allwinner,sun50i-h6-pinctrl
> - allwinner,sun50i-h6-r-pinctrl
> @@ -59,7 +61,7 @@ properties:
>
> interrupts:
> minItems: 1
> - maxItems: 5
> + maxItems: 7
> description:
> One interrupt per external interrupt bank supported on the
> controller, sorted by bank number ascending order.
> @@ -144,75 +146,87 @@ allOf:
> # FIXME: We should have the pin bank supplies here, but not a lot of
> # boards are defining it at the moment so it would generate a lot of
> # warnings.
> -
> - if:
> properties:
> compatible:
> enum:
> - - allwinner,sun9i-a80-pinctrl
> + - allwinner,sun50i-a100-pinctrl
>
> then:
> properties:
> interrupts:
> - minItems: 5
> - maxItems: 5
> + minItems: 7
> + maxItems: 7
>
> else:
> if:
This diff is hard to follow. Rather than a continual nesting of 'else'
clauses, just make each 'if' a new entry under 'allOf' and get rid of
the else. Perhaps do that in a separate patch first, then this change
will be easier to review.
> properties:
> compatible:
> enum:
> - - allwinner,sun6i-a31-pinctrl
> - - allwinner,sun6i-a31s-pinctrl
> - - allwinner,sun50i-h6-pinctrl
> + - allwinner,sun9i-a80-pinctrl
>
> then:
> properties:
> interrupts:
> - minItems: 4
> - maxItems: 4
> + minItems: 5
> + maxItems: 5
>
> else:
> if:
> properties:
> compatible:
> enum:
> - - allwinner,sun8i-a23-pinctrl
> - - allwinner,sun8i-a83t-pinctrl
> - - allwinner,sun50i-a64-pinctrl
> - - allwinner,sun50i-h5-pinctrl
> - - allwinner,suniv-f1c100s-pinctrl
> + - allwinner,sun6i-a31-pinctrl
> + - allwinner,sun6i-a31s-pinctrl
> + - allwinner,sun50i-h6-pinctrl
>
> then:
> properties:
> interrupts:
> - minItems: 3
> - maxItems: 3
> + minItems: 4
> + maxItems: 4
>
> else:
> if:
> properties:
> compatible:
> enum:
> - - allwinner,sun6i-a31-r-pinctrl
> - - allwinner,sun8i-a33-pinctrl
> - - allwinner,sun8i-h3-pinctrl
> - - allwinner,sun8i-v3-pinctrl
> - - allwinner,sun8i-v3s-pinctrl
> - - allwinner,sun9i-a80-r-pinctrl
> - - allwinner,sun50i-h6-r-pinctrl
> + - allwinner,sun8i-a23-pinctrl
> + - allwinner,sun8i-a83t-pinctrl
> + - allwinner,sun50i-a64-pinctrl
> + - allwinner,sun50i-h5-pinctrl
> + - allwinner,suniv-f1c100s-pinctrl
>
> then:
> properties:
> interrupts:
> - minItems: 2
> - maxItems: 2
> + minItems: 3
> + maxItems: 3
>
> else:
> - properties:
> - interrupts:
> - minItems: 1
> - maxItems: 1
> + if:
> + properties:
> + compatible:
> + enum:
> + - allwinner,sun6i-a31-r-pinctrl
> + - allwinner,sun8i-a33-pinctrl
> + - allwinner,sun8i-h3-pinctrl
> + - allwinner,sun8i-v3-pinctrl
> + - allwinner,sun8i-v3s-pinctrl
> + - allwinner,sun9i-a80-r-pinctrl
> + - allwinner,sun50i-h6-r-pinctrl
> +
> + then:
> + properties:
> + interrupts:
> + minItems: 2
> + maxItems: 2
> +
> + else:
> + properties:
> + interrupts:
> + minItems: 1
> + maxItems: 1
>
> additionalProperties: false
>
> --
> 1.9.1
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH v3 07/16] dt-bindings: thermal: sun8i: Add binding for A100's THS controller
2020-07-08 7:19 ` [PATCH v3 07/16] dt-bindings: thermal: sun8i: Add binding for A100's THS controller Frank Lee
@ 2020-07-13 23:02 ` Rob Herring
0 siblings, 0 replies; 22+ messages in thread
From: Rob Herring @ 2020-07-13 23:02 UTC (permalink / raw)
To: Frank Lee
Cc: megous, liyong, tiny.windzz, mturquette, srinivas.kandagatla,
linux-i2c, lee.jones, linux-clk, amit.kucheria, stefan, maz,
gregory.clement, daniel.lezcano, anarsoul, wens, huangshuosheng,
clabbe, rui.zhang, linus.walleij, icenowy, devicetree, jason,
bage, linux-pm, mripard, linux-gpio, robh+dt, tglx,
linux-arm-kernel, sboyd, linux-kernel, p.zabel
On Wed, 08 Jul 2020 15:19:33 +0800, Frank Lee wrote:
> Add a binding for A100's ths controller.
>
> Signed-off-by: Frank Lee <frank@allwinnertech.com>
> Reviewed-by: Yangtao Li <tiny.windzz@gmail.com>
> ---
> .../devicetree/bindings/thermal/allwinner,sun8i-a83t-ths.yaml | 6 +++++-
> 1 file changed, 5 insertions(+), 1 deletion(-)
>
Reviewed-by: Rob Herring <robh@kernel.org>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH v3 01/16] dt-bindings: clk: sunxi-ccu: add compatible string for A100 CCU and R-CCU
2020-07-13 22:54 ` Rob Herring
@ 2020-07-13 23:33 ` Rob Herring
0 siblings, 0 replies; 22+ messages in thread
From: Rob Herring @ 2020-07-13 23:33 UTC (permalink / raw)
To: Frank Lee
Cc: Ondrej Jirman, liyong, Yangtao Li, Michael Turquette,
Srinivas Kandagatla, Linux I2C, Lee Jones, linux-clk,
Amit Kucheria, Stefan Mavrodiev, Marc Zyngier, Gregory CLEMENT,
Daniel Lezcano, Vasily Khoruzhick, Chen-Yu Tsai, huangshuosheng,
Corentin Labbe, Zhang Rui, Linus Walleij, Icenowy Zheng,
devicetree, Jason Cooper, bage, open list:THERMAL, Maxime Ripard,
open list:GPIO SUBSYSTEM, Thomas Gleixner,
moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE,
Stephen Boyd, linux-kernel, Philipp Zabel
On Mon, Jul 13, 2020 at 4:54 PM Rob Herring <robh@kernel.org> wrote:
>
> On Wed, 08 Jul 2020 15:19:27 +0800, Frank Lee wrote:
> > This patch adds binding to a100's ccu clock and r-ccu clock.
> >
> > Signed-off-by: Frank Lee <frank@allwinnertech.com>
> > ---
> > .../devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml | 7 ++++++-
> > 1 file changed, 6 insertions(+), 1 deletion(-)
> >
>
> Reviewed-by: Rob Herring <robh@kernel.org>
Note that your series isn't threaded properly. Please send series
threaded (in reply to cover letter or 1st patch).
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH v3 10/16] mfd: axp20x: Allow the AXP803 to be probed by I2C
2020-07-08 7:19 ` [PATCH v3 10/16] mfd: axp20x: Allow the AXP803 to be probed by I2C Frank Lee
@ 2020-07-16 15:10 ` Lee Jones
0 siblings, 0 replies; 22+ messages in thread
From: Lee Jones @ 2020-07-16 15:10 UTC (permalink / raw)
To: Frank Lee
Cc: megous, liyong, tiny.windzz, linus.walleij, srinivas.kandagatla,
linux-i2c, linux-clk, amit.kucheria, stefan, maz,
gregory.clement, daniel.lezcano, anarsoul, wens, huangshuosheng,
clabbe, rui.zhang, mturquette, icenowy, devicetree, jason, bage,
linux-pm, mripard, linux-gpio, robh+dt, tglx, linux-arm-kernel,
sboyd, linux-kernel, p.zabel
On Wed, 08 Jul 2020, Frank Lee wrote:
> The AXP803 can be used both using the RSB proprietary bus, or a more
> traditional I2C bus.
>
> Let's add that possibility.
>
> Signed-off-by: Frank Lee <frank@allwinnertech.com>
> ---
> drivers/mfd/axp20x-i2c.c | 2 ++
> 1 file changed, 2 insertions(+)
Applied, thanks.
--
Lee Jones [李琼斯]
Senior Technical Lead - Developer Services
Linaro.org │ Open source software for Arm SoCs
Follow Linaro: Facebook | Twitter | Blog
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 22+ messages in thread
end of thread, other threads:[~2020-07-16 15:12 UTC | newest]
Thread overview: 22+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-07-08 7:19 [PATCH v3 00/16] Allwinner A100 Initial support Frank Lee
2020-07-08 7:19 ` [PATCH v3 01/16] dt-bindings: clk: sunxi-ccu: add compatible string for A100 CCU and R-CCU Frank Lee
2020-07-13 22:54 ` Rob Herring
2020-07-13 23:33 ` Rob Herring
2020-07-08 7:19 ` [PATCH v3 02/16] clk: sunxi-ng: add support for the Allwinner A100 CCU Frank Lee
2020-07-08 7:19 ` [PATCH v3 03/16] dt-bindings: pinctrl: sunxi: Add A100 pinctrl bindings Frank Lee
2020-07-13 23:01 ` Rob Herring
2020-07-08 7:19 ` [PATCH v3 04/16] dt-bindings: pinctrl: sunxi: make gpio banks supplies required Frank Lee
2020-07-09 16:52 ` Rob Herring
2020-07-09 16:54 ` Rob Herring
2020-07-09 17:17 ` Ondřej Jirman
2020-07-10 12:37 ` Maxime Ripard
2020-07-08 7:19 ` [PATCH v3 05/16] pinctrl: sunxi: add support for the Allwinner A100 pin controller Frank Lee
2020-07-08 7:19 ` [PATCH v3 06/16] dt-bindings: nvmem: SID: add binding for A100's SID controller Frank Lee
2020-07-09 16:54 ` Rob Herring
2020-07-08 7:19 ` [PATCH v3 07/16] dt-bindings: thermal: sun8i: Add binding for A100's THS controller Frank Lee
2020-07-13 23:02 ` Rob Herring
2020-07-08 7:19 ` [PATCH v3 09/16] thermal: sun8i: Add A100's THS controller support Frank Lee
2020-07-08 7:19 ` [PATCH v3 10/16] mfd: axp20x: Allow the AXP803 to be probed by I2C Frank Lee
2020-07-16 15:10 ` Lee Jones
2020-07-08 7:45 ` [PATCH v3 00/16] Allwinner A100 Initial support Corentin Labbe
2020-07-10 14:28 ` Maxime Ripard
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).