[PATCH AUTOSEL 5.14 01/75] arm64: zynqmp: Do not duplicate flash partition label property

[PATCH AUTOSEL 5.14 01/75] arm64: zynqmp: Do not duplicate flash partition label property

[Sasha Levin]

From: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>

[ Upstream commit 167721a5909f867f8c18c8e78ea58e705ad9bbd4 ]

In kernel 5.4, support has been added for reading MTD devices via the nvmem
API.
For this the mtd devices are registered as read-only NVMEM providers under
sysfs with the same name as the flash partition label property.

So if flash partition label property of multiple flash devices are
identical then the second mtd device fails to get registered as a NVMEM
provider.

This patch fixes the issue by having different label property for different
flashes.

Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/6c4b9b9232b93d9e316a63c086540fd5bf6b8687.1623684253.git.michal.simek@xilinx.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dts | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dts
index 4a86efa32d687..f7124e15f0ff6 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dts
@@ -131,7 +131,7 @@
 		reg = <0>;
 
 		partition@0 {
-			label = "data";
+			label = "spi0-data";
 			reg = <0x0 0x100000>;
 		};
 	};
@@ -149,7 +149,7 @@
 		reg = <0>;
 
 		partition@0 {
-			label = "data";
+			label = "spi1-data";
 			reg = <0x0 0x84000>;
 		};
 	};
-- 
2.33.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.14 02/75] arm64: zynqmp: Fix serial compatible string

[Sasha Levin]

From: Michal Simek <michal.simek@xilinx.com>

[ Upstream commit 812fa2f0e9d33564bd0131a69750e0d165f4c82a ]

Based on commit 65a2c14d4f00 ("dt-bindings: serial: convert Cadence UART
bindings to YAML") compatible string should look like differently that's
why fix it to be aligned with dt binding.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/89b36e0a6187cc6b05b27a035efdf79173bd4486.1628240307.git.michal.simek@xilinx.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/xilinx/zynqmp.dtsi | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
index 28dccb891a535..8278876ad33fa 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
+++ b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
@@ -792,7 +792,7 @@
 		};
 
 		uart0: serial@ff000000 {
-			compatible = "cdns,uart-r1p12", "xlnx,xuartps";
+			compatible = "xlnx,zynqmp-uart", "cdns,uart-r1p12";
 			status = "disabled";
 			interrupt-parent = <&gic>;
 			interrupts = <0 21 4>;
@@ -802,7 +802,7 @@
 		};
 
 		uart1: serial@ff010000 {
-			compatible = "cdns,uart-r1p12", "xlnx,xuartps";
+			compatible = "xlnx,zynqmp-uart", "cdns,uart-r1p12";
 			status = "disabled";
 			interrupt-parent = <&gic>;
 			interrupts = <0 22 4>;
-- 
2.33.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.14 03/75] clk: sunxi-ng: Unregister clocks/resets when unbinding

[Sasha Levin]

From: Samuel Holland <samuel@sholland.org>

[ Upstream commit 9bec2b9c6134052994115d2d3374e96f2ccb9b9d ]

Currently, unbinding a CCU driver unmaps the device's MMIO region, while
leaving its clocks/resets and their providers registered. This can cause
a page fault later when some clock operation tries to perform MMIO. Fix
this by separating the CCU initialization from the memory allocation,
and then using a devres callback to unregister the clocks and resets.

This also fixes a memory leak of the `struct ccu_reset`, and uses the
correct owner (the specific platform driver) for the clocks and resets.

Early OF clock providers are never unregistered, and limited error
handling is possible, so they are mostly unchanged. The error reporting
is made more consistent by moving the message inside of_sunxi_ccu_probe.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210901050526.45673-2-samuel@sholland.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/clk/sunxi-ng/ccu-sun4i-a10.c     |  2 +-
 drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c |  2 +-
 drivers/clk/sunxi-ng/ccu-sun50i-a100.c   |  2 +-
 drivers/clk/sunxi-ng/ccu-sun50i-a64.c    |  2 +-
 drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c   |  2 +-
 drivers/clk/sunxi-ng/ccu-sun50i-h6.c     |  2 +-
 drivers/clk/sunxi-ng/ccu-sun50i-h616.c   |  4 +-
 drivers/clk/sunxi-ng/ccu-sun5i.c         |  2 +-
 drivers/clk/sunxi-ng/ccu-sun6i-a31.c     |  2 +-
 drivers/clk/sunxi-ng/ccu-sun8i-a23.c     |  2 +-
 drivers/clk/sunxi-ng/ccu-sun8i-a33.c     |  2 +-
 drivers/clk/sunxi-ng/ccu-sun8i-a83t.c    |  2 +-
 drivers/clk/sunxi-ng/ccu-sun8i-de2.c     |  2 +-
 drivers/clk/sunxi-ng/ccu-sun8i-h3.c      |  2 +-
 drivers/clk/sunxi-ng/ccu-sun8i-r.c       |  2 +-
 drivers/clk/sunxi-ng/ccu-sun8i-r40.c     |  2 +-
 drivers/clk/sunxi-ng/ccu-sun8i-v3s.c     |  2 +-
 drivers/clk/sunxi-ng/ccu-sun9i-a80-de.c  |  3 +-
 drivers/clk/sunxi-ng/ccu-sun9i-a80-usb.c |  3 +-
 drivers/clk/sunxi-ng/ccu-sun9i-a80.c     |  2 +-
 drivers/clk/sunxi-ng/ccu-suniv-f1c100s.c |  2 +-
 drivers/clk/sunxi-ng/ccu_common.c        | 89 ++++++++++++++++++++----
 drivers/clk/sunxi-ng/ccu_common.h        |  6 +-
 23 files changed, 100 insertions(+), 41 deletions(-)

diff --git a/drivers/clk/sunxi-ng/ccu-sun4i-a10.c b/drivers/clk/sunxi-ng/ccu-sun4i-a10.c
index f32366d9336e7..bd9a8782fec3d 100644
--- a/drivers/clk/sunxi-ng/ccu-sun4i-a10.c
+++ b/drivers/clk/sunxi-ng/ccu-sun4i-a10.c
@@ -1464,7 +1464,7 @@ static void __init sun4i_ccu_init(struct device_node *node,
 	val &= ~GENMASK(7, 6);
 	writel(val | (2 << 6), reg + SUN4I_AHB_REG);
 
-	sunxi_ccu_probe(node, reg, desc);
+	of_sunxi_ccu_probe(node, reg, desc);
 }
 
 static void __init sun4i_a10_ccu_setup(struct device_node *node)
diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c b/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c
index a56142b909938..6f2a589705561 100644
--- a/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c
+++ b/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c
@@ -196,7 +196,7 @@ static int sun50i_a100_r_ccu_probe(struct platform_device *pdev)
 	if (IS_ERR(reg))
 		return PTR_ERR(reg);
 
-	return sunxi_ccu_probe(pdev->dev.of_node, reg, &sun50i_a100_r_ccu_desc);
+	return devm_sunxi_ccu_probe(&pdev->dev, reg, &sun50i_a100_r_ccu_desc);
 }
 
 static const struct of_device_id sun50i_a100_r_ccu_ids[] = {
diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-a100.c b/drivers/clk/sunxi-ng/ccu-sun50i-a100.c
index 81b48c73d389f..913bb08e6dee8 100644
--- a/drivers/clk/sunxi-ng/ccu-sun50i-a100.c
+++ b/drivers/clk/sunxi-ng/ccu-sun50i-a100.c
@@ -1247,7 +1247,7 @@ static int sun50i_a100_ccu_probe(struct platform_device *pdev)
 		writel(val, reg + sun50i_a100_usb2_clk_regs[i]);
 	}
 
-	ret = sunxi_ccu_probe(pdev->dev.of_node, reg, &sun50i_a100_ccu_desc);
+	ret = devm_sunxi_ccu_probe(&pdev->dev, reg, &sun50i_a100_ccu_desc);
 	if (ret)
 		return ret;
 
diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-a64.c b/drivers/clk/sunxi-ng/ccu-sun50i-a64.c
index 149cfde817cba..54f25c624f020 100644
--- a/drivers/clk/sunxi-ng/ccu-sun50i-a64.c
+++ b/drivers/clk/sunxi-ng/ccu-sun50i-a64.c
@@ -955,7 +955,7 @@ static int sun50i_a64_ccu_probe(struct platform_device *pdev)
 
 	writel(0x515, reg + SUN50I_A64_PLL_MIPI_REG);
 
-	ret = sunxi_ccu_probe(pdev->dev.of_node, reg, &sun50i_a64_ccu_desc);
+	ret = devm_sunxi_ccu_probe(&pdev->dev, reg, &sun50i_a64_ccu_desc);
 	if (ret)
 		return ret;
 
diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c b/drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c
index f8909a7ed5539..f30d7eb5424d8 100644
--- a/drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c
+++ b/drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c
@@ -232,7 +232,7 @@ static void __init sunxi_r_ccu_init(struct device_node *node,
 		return;
 	}
 
-	sunxi_ccu_probe(node, reg, desc);
+	of_sunxi_ccu_probe(node, reg, desc);
 }
 
 static void __init sun50i_h6_r_ccu_setup(struct device_node *node)
diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-h6.c b/drivers/clk/sunxi-ng/ccu-sun50i-h6.c
index bff446b782907..c0800da2fa3d7 100644
--- a/drivers/clk/sunxi-ng/ccu-sun50i-h6.c
+++ b/drivers/clk/sunxi-ng/ccu-sun50i-h6.c
@@ -1240,7 +1240,7 @@ static int sun50i_h6_ccu_probe(struct platform_device *pdev)
 	val |= BIT(24);
 	writel(val, reg + SUN50I_H6_HDMI_CEC_CLK_REG);
 
-	return sunxi_ccu_probe(pdev->dev.of_node, reg, &sun50i_h6_ccu_desc);
+	return devm_sunxi_ccu_probe(&pdev->dev, reg, &sun50i_h6_ccu_desc);
 }
 
 static const struct of_device_id sun50i_h6_ccu_ids[] = {
diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-h616.c b/drivers/clk/sunxi-ng/ccu-sun50i-h616.c
index 225307305880e..22eb18079a154 100644
--- a/drivers/clk/sunxi-ng/ccu-sun50i-h616.c
+++ b/drivers/clk/sunxi-ng/ccu-sun50i-h616.c
@@ -1141,9 +1141,7 @@ static void __init sun50i_h616_ccu_setup(struct device_node *node)
 	val |= BIT(24);
 	writel(val, reg + SUN50I_H616_HDMI_CEC_CLK_REG);
 
-	i = sunxi_ccu_probe(node, reg, &sun50i_h616_ccu_desc);
-	if (i)
-		pr_err("%pOF: probing clocks fails: %d\n", node, i);
+	of_sunxi_ccu_probe(node, reg, &sun50i_h616_ccu_desc);
 }
 
 CLK_OF_DECLARE(sun50i_h616_ccu, "allwinner,sun50i-h616-ccu",
diff --git a/drivers/clk/sunxi-ng/ccu-sun5i.c b/drivers/clk/sunxi-ng/ccu-sun5i.c
index b78e9b507c1c6..1f4bc0e773a7e 100644
--- a/drivers/clk/sunxi-ng/ccu-sun5i.c
+++ b/drivers/clk/sunxi-ng/ccu-sun5i.c
@@ -1012,7 +1012,7 @@ static void __init sun5i_ccu_init(struct device_node *node,
 	val &= ~GENMASK(7, 6);
 	writel(val | (2 << 6), reg + SUN5I_AHB_REG);
 
-	sunxi_ccu_probe(node, reg, desc);
+	of_sunxi_ccu_probe(node, reg, desc);
 }
 
 static void __init sun5i_a10s_ccu_setup(struct device_node *node)
diff --git a/drivers/clk/sunxi-ng/ccu-sun6i-a31.c b/drivers/clk/sunxi-ng/ccu-sun6i-a31.c
index 9b40d53266a3f..3df5c0b415804 100644
--- a/drivers/clk/sunxi-ng/ccu-sun6i-a31.c
+++ b/drivers/clk/sunxi-ng/ccu-sun6i-a31.c
@@ -1257,7 +1257,7 @@ static void __init sun6i_a31_ccu_setup(struct device_node *node)
 	val |= 0x3 << 12;
 	writel(val, reg + SUN6I_A31_AHB1_REG);
 
-	sunxi_ccu_probe(node, reg, &sun6i_a31_ccu_desc);
+	of_sunxi_ccu_probe(node, reg, &sun6i_a31_ccu_desc);
 
 	ccu_mux_notifier_register(pll_cpu_clk.common.hw.clk,
 				  &sun6i_a31_cpu_nb);
diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-a23.c b/drivers/clk/sunxi-ng/ccu-sun8i-a23.c
index 103aa504f6c8a..577bb235d6584 100644
--- a/drivers/clk/sunxi-ng/ccu-sun8i-a23.c
+++ b/drivers/clk/sunxi-ng/ccu-sun8i-a23.c
@@ -745,7 +745,7 @@ static void __init sun8i_a23_ccu_setup(struct device_node *node)
 	val &= ~BIT(16);
 	writel(val, reg + SUN8I_A23_PLL_MIPI_REG);
 
-	sunxi_ccu_probe(node, reg, &sun8i_a23_ccu_desc);
+	of_sunxi_ccu_probe(node, reg, &sun8i_a23_ccu_desc);
 }
 CLK_OF_DECLARE(sun8i_a23_ccu, "allwinner,sun8i-a23-ccu",
 	       sun8i_a23_ccu_setup);
diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-a33.c b/drivers/clk/sunxi-ng/ccu-sun8i-a33.c
index 91838cd110377..8f65cd03f5acc 100644
--- a/drivers/clk/sunxi-ng/ccu-sun8i-a33.c
+++ b/drivers/clk/sunxi-ng/ccu-sun8i-a33.c
@@ -805,7 +805,7 @@ static void __init sun8i_a33_ccu_setup(struct device_node *node)
 	val &= ~BIT(16);
 	writel(val, reg + SUN8I_A33_PLL_MIPI_REG);
 
-	sunxi_ccu_probe(node, reg, &sun8i_a33_ccu_desc);
+	of_sunxi_ccu_probe(node, reg, &sun8i_a33_ccu_desc);
 
 	/* Gate then ungate PLL CPU after any rate changes */
 	ccu_pll_notifier_register(&sun8i_a33_pll_cpu_nb);
diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-a83t.c b/drivers/clk/sunxi-ng/ccu-sun8i-a83t.c
index 2b434521c5ccf..c2ddcd2ddab4e 100644
--- a/drivers/clk/sunxi-ng/ccu-sun8i-a83t.c
+++ b/drivers/clk/sunxi-ng/ccu-sun8i-a83t.c
@@ -906,7 +906,7 @@ static int sun8i_a83t_ccu_probe(struct platform_device *pdev)
 	sun8i_a83t_cpu_pll_fixup(reg + SUN8I_A83T_PLL_C0CPUX_REG);
 	sun8i_a83t_cpu_pll_fixup(reg + SUN8I_A83T_PLL_C1CPUX_REG);
 
-	return sunxi_ccu_probe(pdev->dev.of_node, reg, &sun8i_a83t_ccu_desc);
+	return devm_sunxi_ccu_probe(&pdev->dev, reg, &sun8i_a83t_ccu_desc);
 }
 
 static const struct of_device_id sun8i_a83t_ccu_ids[] = {
diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-de2.c b/drivers/clk/sunxi-ng/ccu-sun8i-de2.c
index 524f33275bc73..4b94b6041b271 100644
--- a/drivers/clk/sunxi-ng/ccu-sun8i-de2.c
+++ b/drivers/clk/sunxi-ng/ccu-sun8i-de2.c
@@ -342,7 +342,7 @@ static int sunxi_de2_clk_probe(struct platform_device *pdev)
 		goto err_disable_mod_clk;
 	}
 
-	ret = sunxi_ccu_probe(pdev->dev.of_node, reg, ccu_desc);
+	ret = devm_sunxi_ccu_probe(&pdev->dev, reg, ccu_desc);
 	if (ret)
 		goto err_assert_reset;
 
diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-h3.c b/drivers/clk/sunxi-ng/ccu-sun8i-h3.c
index 7e629a4493afd..d2fc2903787d8 100644
--- a/drivers/clk/sunxi-ng/ccu-sun8i-h3.c
+++ b/drivers/clk/sunxi-ng/ccu-sun8i-h3.c
@@ -1154,7 +1154,7 @@ static void __init sunxi_h3_h5_ccu_init(struct device_node *node,
 	val &= ~GENMASK(19, 16);
 	writel(val | (0 << 16), reg + SUN8I_H3_PLL_AUDIO_REG);
 
-	sunxi_ccu_probe(node, reg, desc);
+	of_sunxi_ccu_probe(node, reg, desc);
 
 	/* Gate then ungate PLL CPU after any rate changes */
 	ccu_pll_notifier_register(&sun8i_h3_pll_cpu_nb);
diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-r.c b/drivers/clk/sunxi-ng/ccu-sun8i-r.c
index 4c8c491b87c27..9e754d1f754a1 100644
--- a/drivers/clk/sunxi-ng/ccu-sun8i-r.c
+++ b/drivers/clk/sunxi-ng/ccu-sun8i-r.c
@@ -265,7 +265,7 @@ static void __init sunxi_r_ccu_init(struct device_node *node,
 		return;
 	}
 
-	sunxi_ccu_probe(node, reg, desc);
+	of_sunxi_ccu_probe(node, reg, desc);
 }
 
 static void __init sun8i_a83t_r_ccu_setup(struct device_node *node)
diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-r40.c b/drivers/clk/sunxi-ng/ccu-sun8i-r40.c
index 84153418453f4..002e0c3a04dbe 100644
--- a/drivers/clk/sunxi-ng/ccu-sun8i-r40.c
+++ b/drivers/clk/sunxi-ng/ccu-sun8i-r40.c
@@ -1346,7 +1346,7 @@ static int sun8i_r40_ccu_probe(struct platform_device *pdev)
 	if (IS_ERR(regmap))
 		return PTR_ERR(regmap);
 
-	ret = sunxi_ccu_probe(pdev->dev.of_node, reg, &sun8i_r40_ccu_desc);
+	ret = devm_sunxi_ccu_probe(&pdev->dev, reg, &sun8i_r40_ccu_desc);
 	if (ret)
 		return ret;
 
diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-v3s.c b/drivers/clk/sunxi-ng/ccu-sun8i-v3s.c
index f49724a22540e..ce150f83ab54e 100644
--- a/drivers/clk/sunxi-ng/ccu-sun8i-v3s.c
+++ b/drivers/clk/sunxi-ng/ccu-sun8i-v3s.c
@@ -822,7 +822,7 @@ static void __init sun8i_v3_v3s_ccu_init(struct device_node *node,
 	val &= ~GENMASK(19, 16);
 	writel(val, reg + SUN8I_V3S_PLL_AUDIO_REG);
 
-	sunxi_ccu_probe(node, reg, ccu_desc);
+	of_sunxi_ccu_probe(node, reg, ccu_desc);
 }
 
 static void __init sun8i_v3s_ccu_setup(struct device_node *node)
diff --git a/drivers/clk/sunxi-ng/ccu-sun9i-a80-de.c b/drivers/clk/sunxi-ng/ccu-sun9i-a80-de.c
index 6616e8114f623..261e64416f26a 100644
--- a/drivers/clk/sunxi-ng/ccu-sun9i-a80-de.c
+++ b/drivers/clk/sunxi-ng/ccu-sun9i-a80-de.c
@@ -246,8 +246,7 @@ static int sun9i_a80_de_clk_probe(struct platform_device *pdev)
 		goto err_disable_clk;
 	}
 
-	ret = sunxi_ccu_probe(pdev->dev.of_node, reg,
-			      &sun9i_a80_de_clk_desc);
+	ret = devm_sunxi_ccu_probe(&pdev->dev, reg, &sun9i_a80_de_clk_desc);
 	if (ret)
 		goto err_assert_reset;
 
diff --git a/drivers/clk/sunxi-ng/ccu-sun9i-a80-usb.c b/drivers/clk/sunxi-ng/ccu-sun9i-a80-usb.c
index 4b4a507d04edf..596243b3e0fa3 100644
--- a/drivers/clk/sunxi-ng/ccu-sun9i-a80-usb.c
+++ b/drivers/clk/sunxi-ng/ccu-sun9i-a80-usb.c
@@ -117,8 +117,7 @@ static int sun9i_a80_usb_clk_probe(struct platform_device *pdev)
 		return ret;
 	}
 
-	ret = sunxi_ccu_probe(pdev->dev.of_node, reg,
-			      &sun9i_a80_usb_clk_desc);
+	ret = devm_sunxi_ccu_probe(&pdev->dev, reg, &sun9i_a80_usb_clk_desc);
 	if (ret)
 		goto err_disable_clk;
 
diff --git a/drivers/clk/sunxi-ng/ccu-sun9i-a80.c b/drivers/clk/sunxi-ng/ccu-sun9i-a80.c
index ef29582676f6e..97aaed0e68500 100644
--- a/drivers/clk/sunxi-ng/ccu-sun9i-a80.c
+++ b/drivers/clk/sunxi-ng/ccu-sun9i-a80.c
@@ -1231,7 +1231,7 @@ static int sun9i_a80_ccu_probe(struct platform_device *pdev)
 	sun9i_a80_cpu_pll_fixup(reg + SUN9I_A80_PLL_C0CPUX_REG);
 	sun9i_a80_cpu_pll_fixup(reg + SUN9I_A80_PLL_C1CPUX_REG);
 
-	return sunxi_ccu_probe(pdev->dev.of_node, reg, &sun9i_a80_ccu_desc);
+	return devm_sunxi_ccu_probe(&pdev->dev, reg, &sun9i_a80_ccu_desc);
 }
 
 static const struct of_device_id sun9i_a80_ccu_ids[] = {
diff --git a/drivers/clk/sunxi-ng/ccu-suniv-f1c100s.c b/drivers/clk/sunxi-ng/ccu-suniv-f1c100s.c
index 7ecc3a5a5b5e1..61ad7ee91c114 100644
--- a/drivers/clk/sunxi-ng/ccu-suniv-f1c100s.c
+++ b/drivers/clk/sunxi-ng/ccu-suniv-f1c100s.c
@@ -538,7 +538,7 @@ static void __init suniv_f1c100s_ccu_setup(struct device_node *node)
 	val &= ~GENMASK(19, 16);
 	writel(val | (3 << 16), reg + SUNIV_PLL_AUDIO_REG);
 
-	sunxi_ccu_probe(node, reg, &suniv_ccu_desc);
+	of_sunxi_ccu_probe(node, reg, &suniv_ccu_desc);
 
 	/* Gate then ungate PLL CPU after any rate changes */
 	ccu_pll_notifier_register(&suniv_pll_cpu_nb);
diff --git a/drivers/clk/sunxi-ng/ccu_common.c b/drivers/clk/sunxi-ng/ccu_common.c
index 2e20e650b6c01..88cb569e58358 100644
--- a/drivers/clk/sunxi-ng/ccu_common.c
+++ b/drivers/clk/sunxi-ng/ccu_common.c
@@ -7,6 +7,7 @@
 
 #include <linux/clk.h>
 #include <linux/clk-provider.h>
+#include <linux/device.h>
 #include <linux/iopoll.h>
 #include <linux/slab.h>
 
@@ -14,6 +15,11 @@
 #include "ccu_gate.h"
 #include "ccu_reset.h"
 
+struct sunxi_ccu {
+	const struct sunxi_ccu_desc	*desc;
+	struct ccu_reset		reset;
+};
+
 static DEFINE_SPINLOCK(ccu_lock);
 
 void ccu_helper_wait_for_lock(struct ccu_common *common, u32 lock)
@@ -79,12 +85,15 @@ int ccu_pll_notifier_register(struct ccu_pll_nb *pll_nb)
 				     &pll_nb->clk_nb);
 }
 
-int sunxi_ccu_probe(struct device_node *node, void __iomem *reg,
-		    const struct sunxi_ccu_desc *desc)
+static int sunxi_ccu_probe(struct sunxi_ccu *ccu, struct device *dev,
+			   struct device_node *node, void __iomem *reg,
+			   const struct sunxi_ccu_desc *desc)
 {
 	struct ccu_reset *reset;
 	int i, ret;
 
+	ccu->desc = desc;
+
 	for (i = 0; i < desc->num_ccu_clks; i++) {
 		struct ccu_common *cclk = desc->ccu_clks[i];
 
@@ -103,7 +112,10 @@ int sunxi_ccu_probe(struct device_node *node, void __iomem *reg,
 			continue;
 
 		name = hw->init->name;
-		ret = of_clk_hw_register(node, hw);
+		if (dev)
+			ret = clk_hw_register(dev, hw);
+		else
+			ret = of_clk_hw_register(node, hw);
 		if (ret) {
 			pr_err("Couldn't register clock %d - %s\n", i, name);
 			goto err_clk_unreg;
@@ -115,15 +127,10 @@ int sunxi_ccu_probe(struct device_node *node, void __iomem *reg,
 	if (ret)
 		goto err_clk_unreg;
 
-	reset = kzalloc(sizeof(*reset), GFP_KERNEL);
-	if (!reset) {
-		ret = -ENOMEM;
-		goto err_alloc_reset;
-	}
-
+	reset = &ccu->reset;
 	reset->rcdev.of_node = node;
 	reset->rcdev.ops = &ccu_reset_ops;
-	reset->rcdev.owner = THIS_MODULE;
+	reset->rcdev.owner = dev ? dev->driver->owner : THIS_MODULE;
 	reset->rcdev.nr_resets = desc->num_resets;
 	reset->base = reg;
 	reset->lock = &ccu_lock;
@@ -131,13 +138,11 @@ int sunxi_ccu_probe(struct device_node *node, void __iomem *reg,
 
 	ret = reset_controller_register(&reset->rcdev);
 	if (ret)
-		goto err_of_clk_unreg;
+		goto err_del_provider;
 
 	return 0;
 
-err_of_clk_unreg:
-	kfree(reset);
-err_alloc_reset:
+err_del_provider:
 	of_clk_del_provider(node);
 err_clk_unreg:
 	while (--i >= 0) {
@@ -149,3 +154,59 @@ err_clk_unreg:
 	}
 	return ret;
 }
+
+static void devm_sunxi_ccu_release(struct device *dev, void *res)
+{
+	struct sunxi_ccu *ccu = res;
+	const struct sunxi_ccu_desc *desc = ccu->desc;
+	int i;
+
+	reset_controller_unregister(&ccu->reset.rcdev);
+	of_clk_del_provider(dev->of_node);
+
+	for (i = 0; i < desc->hw_clks->num; i++) {
+		struct clk_hw *hw = desc->hw_clks->hws[i];
+
+		if (!hw)
+			continue;
+		clk_hw_unregister(hw);
+	}
+}
+
+int devm_sunxi_ccu_probe(struct device *dev, void __iomem *reg,
+			 const struct sunxi_ccu_desc *desc)
+{
+	struct sunxi_ccu *ccu;
+	int ret;
+
+	ccu = devres_alloc(devm_sunxi_ccu_release, sizeof(*ccu), GFP_KERNEL);
+	if (!ccu)
+		return -ENOMEM;
+
+	ret = sunxi_ccu_probe(ccu, dev, dev->of_node, reg, desc);
+	if (ret) {
+		devres_free(ccu);
+		return ret;
+	}
+
+	devres_add(dev, ccu);
+
+	return 0;
+}
+
+void of_sunxi_ccu_probe(struct device_node *node, void __iomem *reg,
+			const struct sunxi_ccu_desc *desc)
+{
+	struct sunxi_ccu *ccu;
+	int ret;
+
+	ccu = kzalloc(sizeof(*ccu), GFP_KERNEL);
+	if (!ccu)
+		return;
+
+	ret = sunxi_ccu_probe(ccu, NULL, node, reg, desc);
+	if (ret) {
+		pr_err("%pOF: probing clocks failed: %d\n", node, ret);
+		kfree(ccu);
+	}
+}
diff --git a/drivers/clk/sunxi-ng/ccu_common.h b/drivers/clk/sunxi-ng/ccu_common.h
index 04e7a12200a21..98a1834b58bb4 100644
--- a/drivers/clk/sunxi-ng/ccu_common.h
+++ b/drivers/clk/sunxi-ng/ccu_common.h
@@ -63,7 +63,9 @@ struct ccu_pll_nb {
 
 int ccu_pll_notifier_register(struct ccu_pll_nb *pll_nb);
 
-int sunxi_ccu_probe(struct device_node *node, void __iomem *reg,
-		    const struct sunxi_ccu_desc *desc);
+int devm_sunxi_ccu_probe(struct device *dev, void __iomem *reg,
+			 const struct sunxi_ccu_desc *desc);
+void of_sunxi_ccu_probe(struct device_node *node, void __iomem *reg,
+			const struct sunxi_ccu_desc *desc);
 
 #endif /* _COMMON_H_ */
-- 
2.33.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.14 04/75] ARM: dts: sunxi: Fix OPPs node name

[Sasha Levin]

From: Maxime Ripard <maxime@cerno.tech>

[ Upstream commit ffbe853a3f5a37fa0a511265b21abf097ffdbe45 ]

The operating-points-v2 nodes are named inconsistently, but mostly
either opp_table0 or gpu-opp-table.  However, the underscore is an
invalid character for a node name and the thermal zone binding
explicitly requires that zones are called opp-table-*. Let's fix it.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20210901091852.479202-43-maxime@cerno.tech
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/sun8i-a33.dtsi                      | 4 ++--
 arch/arm/boot/dts/sun8i-a83t.dtsi                     | 4 ++--
 arch/arm/boot/dts/sun8i-h3.dtsi                       | 4 ++--
 arch/arm64/boot/dts/allwinner/sun50i-a64-cpu-opp.dtsi | 2 +-
 arch/arm64/boot/dts/allwinner/sun50i-h5-cpu-opp.dtsi  | 2 +-
 arch/arm64/boot/dts/allwinner/sun50i-h6-cpu-opp.dtsi  | 2 +-
 6 files changed, 9 insertions(+), 9 deletions(-)

diff --git a/arch/arm/boot/dts/sun8i-a33.dtsi b/arch/arm/boot/dts/sun8i-a33.dtsi
index 2beddbb3c5183..b3d1bdfb5118e 100644
--- a/arch/arm/boot/dts/sun8i-a33.dtsi
+++ b/arch/arm/boot/dts/sun8i-a33.dtsi
@@ -46,7 +46,7 @@
 #include <dt-bindings/thermal/thermal.h>
 
 / {
-	cpu0_opp_table: opp_table0 {
+	cpu0_opp_table: opp-table-cpu {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -164,7 +164,7 @@
 		io-channels = <&ths>;
 	};
 
-	mali_opp_table: gpu-opp-table {
+	mali_opp_table: opp-table-gpu {
 		compatible = "operating-points-v2";
 
 		opp-144000000 {
diff --git a/arch/arm/boot/dts/sun8i-a83t.dtsi b/arch/arm/boot/dts/sun8i-a83t.dtsi
index ac97eac91349b..82fdb04122caa 100644
--- a/arch/arm/boot/dts/sun8i-a83t.dtsi
+++ b/arch/arm/boot/dts/sun8i-a83t.dtsi
@@ -200,7 +200,7 @@
 		status = "disabled";
 	};
 
-	cpu0_opp_table: opp_table0 {
+	cpu0_opp_table: opp-table-cluster0 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -253,7 +253,7 @@
 		};
 	};
 
-	cpu1_opp_table: opp_table1 {
+	cpu1_opp_table: opp-table-cluster1 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
index 4e89701df91f8..ae4f933abb895 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -44,7 +44,7 @@
 #include <dt-bindings/thermal/thermal.h>
 
 / {
-	cpu0_opp_table: opp_table0 {
+	cpu0_opp_table: opp-table-cpu {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -112,7 +112,7 @@
 		};
 	};
 
-	gpu_opp_table: gpu-opp-table {
+	gpu_opp_table: opp-table-gpu {
 		compatible = "operating-points-v2";
 
 		opp-120000000 {
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-cpu-opp.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64-cpu-opp.dtsi
index 578c37490d901..e39db51eb4489 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-cpu-opp.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-cpu-opp.dtsi
@@ -4,7 +4,7 @@
  */
 
 / {
-	cpu0_opp_table: opp_table0 {
+	cpu0_opp_table: opp-table-cpu {
 		compatible = "operating-points-v2";
 		opp-shared;
 
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-cpu-opp.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h5-cpu-opp.dtsi
index b2657201957eb..1afad8b437d72 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h5-cpu-opp.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-cpu-opp.dtsi
@@ -2,7 +2,7 @@
 // Copyright (C) 2020 Chen-Yu Tsai <wens@csie.org>
 
 / {
-	cpu_opp_table: cpu-opp-table {
+	cpu_opp_table: opp-table-cpu {
 		compatible = "operating-points-v2";
 		opp-shared;
 
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-cpu-opp.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6-cpu-opp.dtsi
index 8c6e8536b69fa..0baf0f8e4d272 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h6-cpu-opp.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-cpu-opp.dtsi
@@ -3,7 +3,7 @@
 // Copyright (C) 2020 Clément Péron <peron.clem@gmail.com>
 
 / {
-	cpu_opp_table: cpu-opp-table {
+	cpu_opp_table: opp-table-cpu {
 		compatible = "allwinner,sun50i-h6-operating-points";
 		nvmem-cells = <&cpu_speed_grade>;
 		opp-shared;
-- 
2.33.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.14 05/75] arm64: dts: allwinner: h5: Fix GPU thermal zone node name

[Sasha Levin]

From: Maxime Ripard <maxime@cerno.tech>

[ Upstream commit 94a0f2b0e4e0953d8adf319c44244ef7a57de32c ]

The GPU thermal zone is named gpu_thermal. However, the underscore is
an invalid character for a node name and the thermal zone binding
explicitly requires that zones are called *-thermal. Let's fix it.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20210901091852.479202-48-maxime@cerno.tech
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
index 578a63dedf466..9988e87ea7b3d 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
@@ -217,7 +217,7 @@
 			};
 		};
 
-		gpu_thermal {
+		gpu-thermal {
 			polling-delay-passive = <0>;
 			polling-delay = <0>;
 			thermal-sensors = <&ths 1>;
-- 
2.33.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.14 06/75] arm64: dts: allwinner: a100: Fix thermal zone node name

[Sasha Levin]

From: Maxime Ripard <maxime@cerno.tech>

[ Upstream commit 5c34c4e46e601554bfa370b23c8ae3c3c734e9f7 ]

The thermal zones one the A100 are called $device-thermal-zone.

However, the thermal zone binding explicitly requires that zones are
called *-thermal. Let's fix it.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20210901091852.479202-50-maxime@cerno.tech
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi
index cc321c04f1219..f6d7d7f7fdabe 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi
@@ -343,19 +343,19 @@
 	};
 
 	thermal-zones {
-		cpu-thermal-zone {
+		cpu-thermal {
 			polling-delay-passive = <0>;
 			polling-delay = <0>;
 			thermal-sensors = <&ths 0>;
 		};
 
-		ddr-thermal-zone {
+		ddr-thermal {
 			polling-delay-passive = <0>;
 			polling-delay = <0>;
 			thermal-sensors = <&ths 2>;
 		};
 
-		gpu-thermal-zone {
+		gpu-thermal {
 			polling-delay-passive = <0>;
 			polling-delay = <0>;
 			thermal-sensors = <&ths 1>;
-- 
2.33.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.14 08/75] ARM: dts: BCM5301X: Fix nodes names

[Sasha Levin]

From: Rafał Miłecki <rafal@milecki.pl>

[ Upstream commit 9dba049b6d32e95c0dd2a0d607f593ea288ac140 ]

This fixes following errors for all BCM5301X dts files:
chipcommonA@18000000: $nodename:0: 'chipcommonA@18000000' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
mpcore@19000000: $nodename:0: 'mpcore@19000000' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
mdio-bus-mux@18003000: $nodename:0: 'mdio-bus-mux@18003000' does not match '^mdio-mux[\\-@]?'
dmu@1800c000: $nodename:0: 'dmu@1800c000' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/bcm47094-linksys-panamera.dts | 2 +-
 arch/arm/boot/dts/bcm5301x.dtsi                 | 8 ++++----
 2 files changed, 5 insertions(+), 5 deletions(-)

diff --git a/arch/arm/boot/dts/bcm47094-linksys-panamera.dts b/arch/arm/boot/dts/bcm47094-linksys-panamera.dts
index 05d4f2931772b..9bef6b9bfa8d9 100644
--- a/arch/arm/boot/dts/bcm47094-linksys-panamera.dts
+++ b/arch/arm/boot/dts/bcm47094-linksys-panamera.dts
@@ -129,7 +129,7 @@
 		};
 	};
 
-	mdio-bus-mux@18003000 {
+	mdio-mux@18003000 {
 
 		/* BIT(9) = 1 => external mdio */
 		mdio@200 {
diff --git a/arch/arm/boot/dts/bcm5301x.dtsi b/arch/arm/boot/dts/bcm5301x.dtsi
index f92089290ccd5..f9d3a53065ef7 100644
--- a/arch/arm/boot/dts/bcm5301x.dtsi
+++ b/arch/arm/boot/dts/bcm5301x.dtsi
@@ -19,7 +19,7 @@
 	#size-cells = <1>;
 	interrupt-parent = <&gic>;
 
-	chipcommonA@18000000 {
+	chipcommon-a-bus@18000000 {
 		compatible = "simple-bus";
 		ranges = <0x00000000 0x18000000 0x00001000>;
 		#address-cells = <1>;
@@ -44,7 +44,7 @@
 		};
 	};
 
-	mpcore@19000000 {
+	mpcore-bus@19000000 {
 		compatible = "simple-bus";
 		ranges = <0x00000000 0x19000000 0x00023000>;
 		#address-cells = <1>;
@@ -369,7 +369,7 @@
 		#address-cells = <1>;
 	};
 
-	mdio-bus-mux@18003000 {
+	mdio-mux@18003000 {
 		compatible = "mdio-mux-mmioreg";
 		mdio-parent-bus = <&mdio>;
 		#address-cells = <1>;
@@ -415,7 +415,7 @@
 		status = "disabled";
 	};
 
-	dmu@1800c000 {
+	dmu-bus@1800c000 {
 		compatible = "simple-bus";
 		ranges = <0 0x1800c000 0x1000>;
 		#address-cells = <1>;
-- 
2.33.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.14 09/75] ARM: dts: BCM5301X: Fix MDIO mux binding

[Sasha Levin]

From: Rafał Miłecki <rafal@milecki.pl>

[ Upstream commit 6ee0b56f7530e0ebb496fe15d0b54c5f3a1b5e17 ]

This fixes following error for all BCM5301X dts files:
mdio-bus-mux@18003000: compatible: ['mdio-mux-mmioreg'] is too short

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/bcm5301x.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/bcm5301x.dtsi b/arch/arm/boot/dts/bcm5301x.dtsi
index f9d3a53065ef7..d4f355015e3ca 100644
--- a/arch/arm/boot/dts/bcm5301x.dtsi
+++ b/arch/arm/boot/dts/bcm5301x.dtsi
@@ -370,7 +370,7 @@
 	};
 
 	mdio-mux@18003000 {
-		compatible = "mdio-mux-mmioreg";
+		compatible = "mdio-mux-mmioreg", "mdio-mux";
 		mdio-parent-bus = <&mdio>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-- 
2.33.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.14 10/75] ARM: dts: NSP: Fix mpcore, mmc node names

[Sasha Levin]

From: Matthew Hagan <mnhagan88@gmail.com>

[ Upstream commit 15a563d008ef9d04df525f0c476cd7d7127bb883 ]

Running dtbs_check yielded the issues with bcm-nsp.dtsi.

Firstly this patch fixes the following message by appending "-bus" to
the mpcore node name:
mpcore@19000000: $nodename:0: 'mpcore@19000000' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'

Secondly mmc node name. The label name can remain as is.
sdhci@21000: $nodename:0: 'sdhci@21000' does not match '^mmc(@.*)?$'

Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/bcm-nsp.dtsi | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/bcm-nsp.dtsi b/arch/arm/boot/dts/bcm-nsp.dtsi
index 748df7955ae67..e96ddb2e26e2c 100644
--- a/arch/arm/boot/dts/bcm-nsp.dtsi
+++ b/arch/arm/boot/dts/bcm-nsp.dtsi
@@ -77,7 +77,7 @@
 		interrupt-affinity = <&cpu0>, <&cpu1>;
 	};
 
-	mpcore@19000000 {
+	mpcore-bus@19000000 {
 		compatible = "simple-bus";
 		ranges = <0x00000000 0x19000000 0x00023000>;
 		#address-cells = <1>;
@@ -219,7 +219,7 @@
 			status = "disabled";
 		};
 
-		sdio: sdhci@21000 {
+		sdio: mmc@21000 {
 			compatible = "brcm,sdhci-iproc-cygnus";
 			reg = <0x21000 0x100>;
 			interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>;
-- 
2.33.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.14 11/75] arm64: dts: broadcom: bcm4908: Move reboot syscon out of bus

[Sasha Levin]

From: Rafał Miłecki <rafal@milecki.pl>

[ Upstream commit 6cf9f70255b90b540b9cbde062f18fea29024a75 ]

This fixes following error for every bcm4908 DTS file:
bus@ff800000: reboot: {'type': 'object'} is not allowed for {'compatible': ['syscon-reboot'], 'regmap': [[15]], 'offset': [[52]], 'mask': [[1]]}

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi
index a5a64d17d9ea6..4736416317531 100644
--- a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi
+++ b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi
@@ -326,12 +326,12 @@
 				#reset-cells = <1>;
 			};
 		};
+	};
 
-		reboot {
-			compatible = "syscon-reboot";
-			regmap = <&timer>;
-			offset = <0x34>;
-			mask = <1>;
-		};
+	reboot {
+		compatible = "syscon-reboot";
+		regmap = <&timer>;
+		offset = <0x34>;
+		mask = <1>;
 	};
 };
-- 
2.33.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.14 14/75] arm64: dts: rockchip: Disable CDN DP on Pinebook Pro

[Sasha Levin]

From: Matthias Brugger <mbrugger@suse.com>

[ Upstream commit 2513fa5c25d42f55ca5f0f0ab247af7c9fbfa3b1 ]

The CDN DP needs a PHY and a extcon to work correctly. But no extcon is
provided by the device-tree, which leads to an error:
cdn-dp fec00000.dp: [drm:cdn_dp_probe [rockchipdrm]] *ERROR* missing extcon or phy
cdn-dp: probe of fec00000.dp failed with error -22

Disable the CDN DP to make graphic work on the Pinebook Pro.

Reported-by: Guillaume Gardet <guillaume.gardet@arm.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Link: https://lore.kernel.org/r/20210715164101.11486-1-matthias.bgg@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts | 4 ----
 1 file changed, 4 deletions(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts b/arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts
index 2b5f001ff4a61..9e5d07f5712e6 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts
@@ -385,10 +385,6 @@
 	};
 };
 
-&cdn_dp {
-	status = "okay";
-};
-
 &cpu_b0 {
 	cpu-supply = <&vdd_cpu_b>;
 };
-- 
2.33.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.14 15/75] arm64: dts: hisilicon: fix arm, sp805 compatible string

[Sasha Levin]

From: Michael Walle <michael@walle.cc>

[ Upstream commit 894d4f1f77d0e88f1f81af2e1e37333c1c41b631 ]

According to Documentation/devicetree/bindings/watchdog/arm,sp805.yaml
the compatible is:
  compatible = "arm,sp805", "arm,primecell";

The current compatible string doesn't exist at all. Fix it.

Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/hisilicon/hi3660.dtsi | 4 ++--
 arch/arm64/boot/dts/hisilicon/hi6220.dtsi | 2 +-
 2 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
index f1ec87c058421..ef70144972671 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
@@ -1087,7 +1087,7 @@
 		};
 
 		watchdog0: watchdog@e8a06000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xe8a06000 0x0 0x1000>;
 			interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&crg_ctrl HI3660_OSC32K>,
@@ -1096,7 +1096,7 @@
 		};
 
 		watchdog1: watchdog@e8a07000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xe8a07000 0x0 0x1000>;
 			interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&crg_ctrl HI3660_OSC32K>,
diff --git a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
index dde9371dc5451..e4860b8a638ec 100644
--- a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
@@ -840,7 +840,7 @@
 		};
 
 		watchdog0: watchdog@f8005000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xf8005000 0x0 0x1000>;
 			interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ao_ctrl HI6220_WDT0_PCLK>,
-- 
2.33.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.14 16/75] arm64: dts: rockchip: add Coresight debug range for RK3399

[Sasha Levin]

From: Brian Norris <briannorris@chromium.org>

[ Upstream commit 75dccea503b8e176ad044175e891d7bb291b6ba0 ]

Per Documentation/devicetree/bindings/arm/coresight-cpu-debug.txt.

This IP block can be used for sampling the PC of any given CPU, which is
useful in certain panic scenarios where you can't get the CPU to stop
cleanly (e.g., hard lockup).

Reviewed-by: Leo Yan <leo.yan@linaro.org>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Link: https://lore.kernel.org/r/20210908111337.v2.3.Ibc87b4785709543c998cc852c1edaeb7a08edf5c@changeid
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/rockchip/rk3399.dtsi | 48 ++++++++++++++++++++++++
 1 file changed, 48 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3399.dtsi b/arch/arm64/boot/dts/rockchip/rk3399.dtsi
index 3871c7fd83b00..c5fe2d4401149 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399.dtsi
@@ -361,6 +361,54 @@
 		status = "disabled";
 	};
 
+	debug@fe430000 {
+		compatible = "arm,coresight-cpu-debug", "arm,primecell";
+		reg = <0 0xfe430000 0 0x1000>;
+		clocks = <&cru PCLK_COREDBG_L>;
+		clock-names = "apb_pclk";
+		cpu = <&cpu_l0>;
+	};
+
+	debug@fe432000 {
+		compatible = "arm,coresight-cpu-debug", "arm,primecell";
+		reg = <0 0xfe432000 0 0x1000>;
+		clocks = <&cru PCLK_COREDBG_L>;
+		clock-names = "apb_pclk";
+		cpu = <&cpu_l1>;
+	};
+
+	debug@fe434000 {
+		compatible = "arm,coresight-cpu-debug", "arm,primecell";
+		reg = <0 0xfe434000 0 0x1000>;
+		clocks = <&cru PCLK_COREDBG_L>;
+		clock-names = "apb_pclk";
+		cpu = <&cpu_l2>;
+	};
+
+	debug@fe436000 {
+		compatible = "arm,coresight-cpu-debug", "arm,primecell";
+		reg = <0 0xfe436000 0 0x1000>;
+		clocks = <&cru PCLK_COREDBG_L>;
+		clock-names = "apb_pclk";
+		cpu = <&cpu_l3>;
+	};
+
+	debug@fe610000 {
+		compatible = "arm,coresight-cpu-debug", "arm,primecell";
+		reg = <0 0xfe610000 0 0x1000>;
+		clocks = <&cru PCLK_COREDBG_B>;
+		clock-names = "apb_pclk";
+		cpu = <&cpu_b0>;
+	};
+
+	debug@fe710000 {
+		compatible = "arm,coresight-cpu-debug", "arm,primecell";
+		reg = <0 0xfe710000 0 0x1000>;
+		clocks = <&cru PCLK_COREDBG_B>;
+		clock-names = "apb_pclk";
+		cpu = <&cpu_b1>;
+	};
+
 	usbdrd3_0: usb@fe800000 {
 		compatible = "rockchip,rk3399-dwc3";
 		#address-cells = <2>;
-- 
2.33.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.14 22/75] ARM: dts: ux500: Skomer regulator fixes

[Sasha Levin]

From: Linus Walleij <linus.walleij@linaro.org>

[ Upstream commit 7aee0288beab72cdfa35af51f62e94373fca595d ]

AUX2 has slightly wrong voltage and AUX5 doesn't need to be
always on.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/ste-ux500-samsung-skomer.dts | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/ste-ux500-samsung-skomer.dts b/arch/arm/boot/dts/ste-ux500-samsung-skomer.dts
index 94afd7a0fe1f0..9a90e7bbb4673 100644
--- a/arch/arm/boot/dts/ste-ux500-samsung-skomer.dts
+++ b/arch/arm/boot/dts/ste-ux500-samsung-skomer.dts
@@ -290,10 +290,10 @@
 					};
 
 					ab8500_ldo_aux2 {
-						/* Supplies the Cypress TMA140 touchscreen only with 3.3V */
+						/* Supplies the Cypress TMA140 touchscreen only with 3.0V */
 						regulator-name = "AUX2";
-						regulator-min-microvolt = <3300000>;
-						regulator-max-microvolt = <3300000>;
+						regulator-min-microvolt = <3000000>;
+						regulator-max-microvolt = <3000000>;
 					};
 
 					ab8500_ldo_aux3 {
@@ -312,9 +312,9 @@
 
 					ab8500_ldo_aux5 {
 						regulator-name = "AUX5";
+						/* Intended for 1V8 for touchscreen but actually left unused */
 						regulator-min-microvolt = <1050000>;
 						regulator-max-microvolt = <2790000>;
-						regulator-always-on;
 					};
 
 					ab8500_ldo_aux6 {
-- 
2.33.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.14 25/75] ARM: BCM53016: Specify switch ports for Meraki MR32

[Sasha Levin]

From: Christian Lamparter <chunkeey@gmail.com>

[ Upstream commit 6abc4ca5a28070945e0d68cb4160b309bfbf4b8b ]

the switch identifies itself as a BCM53012 (rev 5)...
This patch has been tested & verified on OpenWrt's
snapshot with Linux 5.10 (didn't test any older kernels).
The MR32 is able to "talk to the network" as before with
OpenWrt's SWITCHDEV b53 driver.

| b53-srab-switch 18007000.ethernet-switch: found switch: BCM53012, rev 5
| libphy: dsa slave smi: probed
| b53-srab-switch 18007000.ethernet-switch poe (uninitialized):
|	PHY [dsa-0.0:00] driver [Generic PHY] (irq=POLL)
| b53-srab-switch 18007000.ethernet-switch: Using legacy PHYLIB callbacks.
|	Please migrate to PHYLINK!
| DSA: tree 0 setup

Reported-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/bcm53016-meraki-mr32.dts | 22 ++++++++++++++++++++++
 1 file changed, 22 insertions(+)

diff --git a/arch/arm/boot/dts/bcm53016-meraki-mr32.dts b/arch/arm/boot/dts/bcm53016-meraki-mr32.dts
index 3b978dc8997a4..1dbfa05b65015 100644
--- a/arch/arm/boot/dts/bcm53016-meraki-mr32.dts
+++ b/arch/arm/boot/dts/bcm53016-meraki-mr32.dts
@@ -195,3 +195,25 @@
 		};
 	};
 };
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			reg = <0>;
+			label = "poe";
+		};
+
+		port@5 {
+			reg = <5>;
+			label = "cpu";
+			ethernet = <&gmac0>;
+
+			fixed-link {
+				speed = <1000>;
+				duplex-full;
+			};
+		};
+	};
+};
-- 
2.33.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.14 26/75] arm64: dts: qcom: msm8998: Fix CPU/L2 idle state latency and residency

[Sasha Levin]

From: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>

[ Upstream commit 3f1dcaff642e75c1d2ad03f783fa8a3b1f56dd50 ]

The entry/exit latency and minimum residency in state for the idle
states of MSM8998 were ..bad: first of all, for all of them the
timings were written for CPU sleep but the min-residency-us param
was miscalculated (supposedly, while porting this from downstream);
Then, the power collapse states are setting PC on both the CPU
cluster *and* the L2 cache, which have different timings: in the
specific case of L2 the times are higher so these ones should be
taken into account instead of the CPU ones.

This parameter misconfiguration was not giving particular issues
because on MSM8998 there was no CPU scaling at all, so cluster/L2
power collapse was rarely (if ever) hit.
When CPU scaling is enabled, though, the wrong timings will produce
SoC unstability shown to the user as random, apparently error-less,
sudden reboots and/or lockups.

This set of parameters are stabilizing the SoC when CPU scaling is
ON and when power collapse is frequently hit.

Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210901183123.1087392-3-angelogioacchino.delregno@somainline.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/qcom/msm8998.dtsi | 20 ++++++++++++--------
 1 file changed, 12 insertions(+), 8 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/msm8998.dtsi b/arch/arm64/boot/dts/qcom/msm8998.dtsi
index e9d3ce29937c4..b1cf28ddd5697 100644
--- a/arch/arm64/boot/dts/qcom/msm8998.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8998.dtsi
@@ -308,38 +308,42 @@
 			LITTLE_CPU_SLEEP_0: cpu-sleep-0-0 {
 				compatible = "arm,idle-state";
 				idle-state-name = "little-retention";
+				/* CPU Retention (C2D), L2 Active */
 				arm,psci-suspend-param = <0x00000002>;
 				entry-latency-us = <81>;
 				exit-latency-us = <86>;
-				min-residency-us = <200>;
+				min-residency-us = <504>;
 			};
 
 			LITTLE_CPU_SLEEP_1: cpu-sleep-0-1 {
 				compatible = "arm,idle-state";
 				idle-state-name = "little-power-collapse";
+				/* CPU + L2 Power Collapse (C3, D4) */
 				arm,psci-suspend-param = <0x40000003>;
-				entry-latency-us = <273>;
-				exit-latency-us = <612>;
-				min-residency-us = <1000>;
+				entry-latency-us = <814>;
+				exit-latency-us = <4562>;
+				min-residency-us = <9183>;
 				local-timer-stop;
 			};
 
 			BIG_CPU_SLEEP_0: cpu-sleep-1-0 {
 				compatible = "arm,idle-state";
 				idle-state-name = "big-retention";
+				/* CPU Retention (C2D), L2 Active */
 				arm,psci-suspend-param = <0x00000002>;
 				entry-latency-us = <79>;
 				exit-latency-us = <82>;
-				min-residency-us = <200>;
+				min-residency-us = <1302>;
 			};
 
 			BIG_CPU_SLEEP_1: cpu-sleep-1-1 {
 				compatible = "arm,idle-state";
 				idle-state-name = "big-power-collapse";
+				/* CPU + L2 Power Collapse (C3, D4) */
 				arm,psci-suspend-param = <0x40000003>;
-				entry-latency-us = <336>;
-				exit-latency-us = <525>;
-				min-residency-us = <1000>;
+				entry-latency-us = <724>;
+				exit-latency-us = <2027>;
+				min-residency-us = <9419>;
 				local-timer-stop;
 			};
 		};
-- 
2.33.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.14 27/75] arm64: dts: qcom: ipq6018: Fix qcom, controlled-remotely property

[Sasha Levin]

From: Shawn Guo <shawn.guo@linaro.org>

[ Upstream commit 3509de752ea14c7e5781b3a56a4a0bf832f5723a ]

Property qcom,controlled-remotely should be boolean.  Fix it.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210829111628.5543-2-shawn.guo@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/qcom/ipq6018.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
index 23ee1bfa43189..81a29d87997a4 100644
--- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
@@ -200,7 +200,7 @@
 			clock-names = "bam_clk";
 			#dma-cells = <1>;
 			qcom,ee = <1>;
-			qcom,controlled-remotely = <1>;
+			qcom,controlled-remotely;
 			qcom,config-pipe-trust-reg = <0>;
 		};
 
-- 
2.33.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.14 28/75] arm64: dts: qcom: sdm845: Fix qcom, controlled-remotely property

[Sasha Levin]

From: Shawn Guo <shawn.guo@linaro.org>

[ Upstream commit 1c8bf398b6b51eb085a49036ad8f9c000171cce1 ]

Property qcom,controlled-remotely should be boolean.  Fix it.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210829111628.5543-4-shawn.guo@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/qcom/sdm845.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi
index 0a86fe71a66d1..56e71106fb537 100644
--- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
@@ -2320,7 +2320,7 @@
 			clock-names = "bam_clk";
 			#dma-cells = <1>;
 			qcom,ee = <0>;
-			qcom,controlled-remotely = <1>;
+			qcom,controlled-remotely;
 			iommus = <&apps_smmu 0x704 0x1>,
 				 <&apps_smmu 0x706 0x1>,
 				 <&apps_smmu 0x714 0x1>,
-- 
2.33.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.14 29/75] arm64: dts: qcom: msm8916: Add unit name for /soc node

[Sasha Levin]

From: Stephan Gerhold <stephan@gerhold.net>

[ Upstream commit 7a62bfebc8c94bdb6eb8f54f49889dc6b5b79601 ]

This fixes the following warning when building with W=1:
Warning (unit_address_vs_reg): /soc: node has a reg or ranges property,
but no unit name

Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210921152120.6710-1-stephan@gerhold.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/qcom/msm8916.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
index 4f06c0a9c4252..fa26d3871e00a 100644
--- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
@@ -414,7 +414,7 @@
 		};
 	};
 
-	soc: soc {
+	soc: soc@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0 0 0xffffffff>;
-- 
2.33.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.14 30/75] arm64: dts: freescale: fix arm, sp805 compatible string

[Sasha Levin]

From: Michael Walle <michael@walle.cc>

[ Upstream commit 99a7cacc66cae92db40139b57689be2af75fc6b8 ]

According to Documentation/devicetree/bindings/watchdog/arm,sp805.yaml
the compatible is:
  compatible = "arm,sp805", "arm,primecell";

The current compatible string doesn't exist at all. Fix it.

Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi | 16 ++++++++--------
 arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi | 16 ++++++++--------
 2 files changed, 16 insertions(+), 16 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
index 2fa6cfbef01f9..5a04e30a9a5db 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
@@ -829,7 +829,7 @@
 		};
 
 		cluster1_core0_watchdog: wdt@c000000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc000000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(16)>,
@@ -839,7 +839,7 @@
 		};
 
 		cluster1_core1_watchdog: wdt@c010000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc010000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(16)>,
@@ -849,7 +849,7 @@
 		};
 
 		cluster1_core2_watchdog: wdt@c020000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc020000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(16)>,
@@ -859,7 +859,7 @@
 		};
 
 		cluster1_core3_watchdog: wdt@c030000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc030000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(16)>,
@@ -869,7 +869,7 @@
 		};
 
 		cluster2_core0_watchdog: wdt@c100000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc100000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(16)>,
@@ -879,7 +879,7 @@
 		};
 
 		cluster2_core1_watchdog: wdt@c110000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc110000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(16)>,
@@ -889,7 +889,7 @@
 		};
 
 		cluster2_core2_watchdog: wdt@c120000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc120000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(16)>,
@@ -899,7 +899,7 @@
 		};
 
 		cluster2_core3_watchdog: wdt@c130000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc130000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(16)>,
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi
index 801ba9612d361..1282b61da8a55 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi
@@ -387,7 +387,7 @@
 		};
 
 		cluster1_core0_watchdog: wdt@c000000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc000000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(4)>,
@@ -397,7 +397,7 @@
 		};
 
 		cluster1_core1_watchdog: wdt@c010000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc010000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(4)>,
@@ -407,7 +407,7 @@
 		};
 
 		cluster2_core0_watchdog: wdt@c100000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc100000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(4)>,
@@ -417,7 +417,7 @@
 		};
 
 		cluster2_core1_watchdog: wdt@c110000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc110000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(4)>,
@@ -427,7 +427,7 @@
 		};
 
 		cluster3_core0_watchdog: wdt@c200000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc200000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(4)>,
@@ -437,7 +437,7 @@
 		};
 
 		cluster3_core1_watchdog: wdt@c210000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc210000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(4)>,
@@ -447,7 +447,7 @@
 		};
 
 		cluster4_core0_watchdog: wdt@c300000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc300000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(4)>,
@@ -457,7 +457,7 @@
 		};
 
 		cluster4_core1_watchdog: wdt@c310000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc310000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(4)>,
-- 
2.33.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.14 31/75] arm64: dts: ls1012a: Add serial alias for ls1012a-rdb

[Sasha Levin]

From: Kuldeep Singh <kuldeep.singh@nxp.com>

[ Upstream commit 7f31ae6e01da140e34d6513815253e811019f016 ]

U-boot atempts to read serial alias value for ls1012a-rdb but couldn't
do so as it is not initialised and thus, FDT_ERR_NOTFOUND error is
reported while booting linux.

Loading fdt from FIT Image at a0000000 ...
   Description:  ls1012ardb-dtb
     Type:         Flat Device Tree
     Data Start:   0xab111474
     Data Size:    11285 Bytes = 11 KiB
     Architecture: AArch64
     Load Address: 0x90000000
   Loading fdt from 0xab111474 to 0x90000000
   Booting using the fdt blob at 0x90000000
   Uncompressing Kernel Image
   Loading Device Tree to 000000008fffa000, end 000000008ffffc14 ... OK
WARNING: fdt_fixup_stdout: could not read serial0 alias: FDT_ERR_NOTFOUND
NOTICE:  RNG: INSTANTIATED

Starting kernel ...

Fix the above error by specifying serial value to duart.

Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts
index 79f155dedb2d0..e662677a6e28f 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts
@@ -15,6 +15,7 @@
 	compatible = "fsl,ls1012a-rdb", "fsl,ls1012a";
 
 	aliases {
+		serial0 = &duart0;
 		mmc0 = &esdhc0;
 		mmc1 = &esdhc1;
 	};
-- 
2.33.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.14 36/75] clk: imx: imx6ul: Move csi_sel mux to correct base register

[Sasha Levin]

From: Stefan Riedmueller <s.riedmueller@phytec.de>

[ Upstream commit 2f9d61869640f732599ec36b984c2b5c46067519 ]

The csi_sel mux register is located in the CCM register base and not the
CCM_ANALOG register base. So move it to the correct position in code.

Otherwise changing the parent of the csi clock can lead to a complete
system failure due to the CCM_ANALOG_PLL_SYS_TOG register being falsely
modified.

Also remove the SET_RATE_PARENT flag since one possible supply for the
csi_sel mux is the system PLL which we don't want to modify.

Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20210927072857.3940880-1-s.riedmueller@phytec.de
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/clk/imx/clk-imx6ul.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/clk/imx/clk-imx6ul.c b/drivers/clk/imx/clk-imx6ul.c
index 5dbb6a9377324..206e4c43f68f8 100644
--- a/drivers/clk/imx/clk-imx6ul.c
+++ b/drivers/clk/imx/clk-imx6ul.c
@@ -161,7 +161,6 @@ static void __init imx6ul_clocks_init(struct device_node *ccm_node)
 	hws[IMX6UL_PLL5_BYPASS] = imx_clk_hw_mux_flags("pll5_bypass", base + 0xa0, 16, 1, pll5_bypass_sels, ARRAY_SIZE(pll5_bypass_sels), CLK_SET_RATE_PARENT);
 	hws[IMX6UL_PLL6_BYPASS] = imx_clk_hw_mux_flags("pll6_bypass", base + 0xe0, 16, 1, pll6_bypass_sels, ARRAY_SIZE(pll6_bypass_sels), CLK_SET_RATE_PARENT);
 	hws[IMX6UL_PLL7_BYPASS] = imx_clk_hw_mux_flags("pll7_bypass", base + 0x20, 16, 1, pll7_bypass_sels, ARRAY_SIZE(pll7_bypass_sels), CLK_SET_RATE_PARENT);
-	hws[IMX6UL_CLK_CSI_SEL] = imx_clk_hw_mux_flags("csi_sel", base + 0x3c, 9, 2, csi_sels, ARRAY_SIZE(csi_sels), CLK_SET_RATE_PARENT);
 
 	/* Do not bypass PLLs initially */
 	clk_set_parent(hws[IMX6UL_PLL1_BYPASS]->clk, hws[IMX6UL_CLK_PLL1]->clk);
@@ -270,6 +269,7 @@ static void __init imx6ul_clocks_init(struct device_node *ccm_node)
 	hws[IMX6UL_CLK_ECSPI_SEL]	  = imx_clk_hw_mux("ecspi_sel",	base + 0x38, 18, 1, ecspi_sels, ARRAY_SIZE(ecspi_sels));
 	hws[IMX6UL_CLK_LCDIF_PRE_SEL]	  = imx_clk_hw_mux_flags("lcdif_pre_sel", base + 0x38, 15, 3, lcdif_pre_sels, ARRAY_SIZE(lcdif_pre_sels), CLK_SET_RATE_PARENT);
 	hws[IMX6UL_CLK_LCDIF_SEL]	  = imx_clk_hw_mux("lcdif_sel",	base + 0x38, 9, 3, lcdif_sels, ARRAY_SIZE(lcdif_sels));
+	hws[IMX6UL_CLK_CSI_SEL]		  = imx_clk_hw_mux("csi_sel", base + 0x3c, 9, 2, csi_sels, ARRAY_SIZE(csi_sels));
 
 	hws[IMX6UL_CLK_LDB_DI0_DIV_SEL]  = imx_clk_hw_mux("ldb_di0", base + 0x20, 10, 1, ldb_di0_div_sels, ARRAY_SIZE(ldb_di0_div_sels));
 	hws[IMX6UL_CLK_LDB_DI1_DIV_SEL]  = imx_clk_hw_mux("ldb_di1", base + 0x20, 11, 1, ldb_di1_div_sels, ARRAY_SIZE(ldb_di1_div_sels));
-- 
2.33.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.14 42/75] arm64: dts: imx8mm-kontron: Fix reset delays for ethernet PHY

[Sasha Levin]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

[ Upstream commit 315e7b884190a6c9c28e95ad3b724dde9e922b99 ]

According to the datasheet the VSC8531 PHY expects a reset pulse of 100 ns
and a delay of 15 ms after the reset has been deasserted. Set the matching
values in the devicetree.

Reported-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
index e99e7644ff392..49d7470812eef 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
@@ -123,8 +123,8 @@
 
 		ethphy: ethernet-phy@0 {
 			reg = <0>;
-			reset-assert-us = <100>;
-			reset-deassert-us = <100>;
+			reset-assert-us = <1>;
+			reset-deassert-us = <15000>;
 			reset-gpios = <&gpio4 27 GPIO_ACTIVE_LOW>;
 		};
 	};
-- 
2.33.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.14 50/75] ARM: dts: omap: fix gpmc, mux-add-data type

[Sasha Levin]

From: Roger Quadros <rogerq@kernel.org>

[ Upstream commit 51b9e22ffd3c4c56cbb7caae9750f70e55ffa603 ]

gpmc,mux-add-data is not boolean.

Fixes the below errors flagged by dtbs_check.

"ethernet@4,0:gpmc,mux-add-data: True is not of type 'array'"

Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/omap-gpmc-smsc9221.dtsi         | 2 +-
 arch/arm/boot/dts/omap3-overo-tobiduo-common.dtsi | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/omap-gpmc-smsc9221.dtsi b/arch/arm/boot/dts/omap-gpmc-smsc9221.dtsi
index 7f6aefd134514..e7534fe9c53cf 100644
--- a/arch/arm/boot/dts/omap-gpmc-smsc9221.dtsi
+++ b/arch/arm/boot/dts/omap-gpmc-smsc9221.dtsi
@@ -29,7 +29,7 @@
 		compatible = "smsc,lan9221","smsc,lan9115";
 		bank-width = <2>;
 
-		gpmc,mux-add-data;
+		gpmc,mux-add-data = <0>;
 		gpmc,cs-on-ns = <0>;
 		gpmc,cs-rd-off-ns = <42>;
 		gpmc,cs-wr-off-ns = <36>;
diff --git a/arch/arm/boot/dts/omap3-overo-tobiduo-common.dtsi b/arch/arm/boot/dts/omap3-overo-tobiduo-common.dtsi
index e5da3bc6f1050..218a10c0d8159 100644
--- a/arch/arm/boot/dts/omap3-overo-tobiduo-common.dtsi
+++ b/arch/arm/boot/dts/omap3-overo-tobiduo-common.dtsi
@@ -22,7 +22,7 @@
 		compatible = "smsc,lan9221","smsc,lan9115";
 		bank-width = <2>;
 
-		gpmc,mux-add-data;
+		gpmc,mux-add-data = <0>;
 		gpmc,cs-on-ns = <0>;
 		gpmc,cs-rd-off-ns = <42>;
 		gpmc,cs-wr-off-ns = <36>;
-- 
2.33.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.14 52/75] ARM: dts: ls1021a: move thermal-zones node out of soc/

[Sasha Levin]

From: Li Yang <leoyang.li@nxp.com>

[ Upstream commit 1ee1500ef717eefb5d9bdaf97905cb81b4e69aa4 ]

This fixes dtbs-check error from simple-bus schema:
soc: thermal-zones: {'type': 'object'} is not allowed for {'cpu-thermal': ..... }
        From schema: /home/leo/.local/lib/python3.8/site-packages/dtschema/schemas/simple-bus.yaml

Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/ls1021a.dtsi | 66 +++++++++++++++++-----------------
 1 file changed, 33 insertions(+), 33 deletions(-)

diff --git a/arch/arm/boot/dts/ls1021a.dtsi b/arch/arm/boot/dts/ls1021a.dtsi
index 4fce81422943b..f3b8540750b61 100644
--- a/arch/arm/boot/dts/ls1021a.dtsi
+++ b/arch/arm/boot/dts/ls1021a.dtsi
@@ -329,39 +329,6 @@
 			#thermal-sensor-cells = <1>;
 		};
 
-		thermal-zones {
-			cpu_thermal: cpu-thermal {
-				polling-delay-passive = <1000>;
-				polling-delay = <5000>;
-
-				thermal-sensors = <&tmu 0>;
-
-				trips {
-					cpu_alert: cpu-alert {
-						temperature = <85000>;
-						hysteresis = <2000>;
-						type = "passive";
-					};
-					cpu_crit: cpu-crit {
-						temperature = <95000>;
-						hysteresis = <2000>;
-						type = "critical";
-					};
-				};
-
-				cooling-maps {
-					map0 {
-						trip = <&cpu_alert>;
-						cooling-device =
-							<&cpu0 THERMAL_NO_LIMIT
-							THERMAL_NO_LIMIT>,
-							<&cpu1 THERMAL_NO_LIMIT
-							THERMAL_NO_LIMIT>;
-					};
-				};
-			};
-		};
-
 		dspi0: spi@2100000 {
 			compatible = "fsl,ls1021a-v1.0-dspi";
 			#address-cells = <1>;
@@ -1016,4 +983,37 @@
 			big-endian;
 		};
 	};
+
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive = <1000>;
+			polling-delay = <5000>;
+
+			thermal-sensors = <&tmu 0>;
+
+			trips {
+				cpu_alert: cpu-alert {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu_crit: cpu-crit {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu_alert>;
+					cooling-device =
+						<&cpu0 THERMAL_NO_LIMIT
+						THERMAL_NO_LIMIT>,
+						<&cpu1 THERMAL_NO_LIMIT
+						THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
 };
-- 
2.33.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.14 53/75] ARM: dts: ls1021a-tsn: use generic "jedec, spi-nor" compatible for flash

[Sasha Levin]

From: Li Yang <leoyang.li@nxp.com>

[ Upstream commit 05e63b48b20fa70726be505a7660d1a07bc1cffb ]

We cannot list all the possible chips used in different board revisions,
just use the generic "jedec,spi-nor" compatible instead.  This also
fixes dtbs_check error:
['jedec,spi-nor', 's25fl256s1', 's25fl512s'] is too long

Signed-off-by: Li Yang <leoyang.li@nxp.com>
Reviewed-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/ls1021a-tsn.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/ls1021a-tsn.dts b/arch/arm/boot/dts/ls1021a-tsn.dts
index 9d8f0c2a8aba3..aca78b5eddf20 100644
--- a/arch/arm/boot/dts/ls1021a-tsn.dts
+++ b/arch/arm/boot/dts/ls1021a-tsn.dts
@@ -251,7 +251,7 @@
 
 	flash@0 {
 		/* Rev. A uses 64MB flash, Rev. B & C use 32MB flash */
-		compatible = "jedec,spi-nor", "s25fl256s1", "s25fl512s";
+		compatible = "jedec,spi-nor";
 		spi-max-frequency = <20000000>;
 		#address-cells = <1>;
 		#size-cells = <1>;
-- 
2.33.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.14 60/75] scsi: target: Fix ordered tag handling

[Sasha Levin]

From: Mike Christie <michael.christie@oracle.com>

[ Upstream commit ed1227e080990ffec5bf39006ec8a57358e6689a ]

This patch fixes the following bugs:

1. If there are multiple ordered cmds queued and multiple simple cmds
   completing, target_restart_delayed_cmds() could be called on different
   CPUs and each instance could start a ordered cmd. They could then run in
   different orders than they were queued.

2. target_restart_delayed_cmds() and target_handle_task_attr() can race
   where:

   1. target_handle_task_attr() has passed the simple_cmds == 0 check.

   2. transport_complete_task_attr() then decrements simple_cmds to 0.

   3. transport_complete_task_attr() runs target_restart_delayed_cmds() and
      it does not see any cmds on the delayed_cmd_list.

   4. target_handle_task_attr() adds the cmd to the delayed_cmd_list.

   The cmd will then end up timing out.

3. If we are sent > 1 ordered cmds and simple_cmds == 0, we can execute
   them out of order, because target_handle_task_attr() will hit that
   simple_cmds check first and return false for all ordered cmds sent.

4. We run target_restart_delayed_cmds() after every cmd completion, so if
   there is more than 1 simple cmd running, we start executing ordered cmds
   after that first cmd instead of waiting for all of them to complete.

5. Ordered cmds are not supposed to start until HEAD OF QUEUE and all older
   cmds have completed, and not just simple.

6. It's not a bug but it doesn't make sense to take the delayed_cmd_lock
   for every cmd completion when ordered cmds are almost never used. Just
   replacing that lock with an atomic increases IOPs by up to 10% when
   completions are spread over multiple CPUs and there are multiple
   sessions/ mqs/thread accessing the same device.

This patch moves the queued delayed handling to a per device work to
serialze the cmd executions for each device and adds a new counter to track
HEAD_OF_QUEUE and SIMPLE cmds. We can then check the new counter to
determine when to run the work on the completion path.

Link: https://lore.kernel.org/r/20210930020422.92578-3-michael.christie@oracle.com
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/target/target_core_device.c    |  2 +
 drivers/target/target_core_internal.h  |  1 +
 drivers/target/target_core_transport.c | 76 ++++++++++++++++++--------
 include/target/target_core_base.h      |  6 +-
 4 files changed, 61 insertions(+), 24 deletions(-)

diff --git a/drivers/target/target_core_device.c b/drivers/target/target_core_device.c
index 8cb1fa0c05857..44bb380e7390c 100644
--- a/drivers/target/target_core_device.c
+++ b/drivers/target/target_core_device.c
@@ -772,6 +772,8 @@ struct se_device *target_alloc_device(struct se_hba *hba, const char *name)
 	INIT_LIST_HEAD(&dev->t10_alua.lba_map_list);
 	spin_lock_init(&dev->t10_alua.lba_map_lock);
 
+	INIT_WORK(&dev->delayed_cmd_work, target_do_delayed_work);
+
 	dev->t10_wwn.t10_dev = dev;
 	/*
 	 * Use OpenFabrics IEEE Company ID: 00 14 05
diff --git a/drivers/target/target_core_internal.h b/drivers/target/target_core_internal.h
index a343bcfa2180f..a889a6237d9c1 100644
--- a/drivers/target/target_core_internal.h
+++ b/drivers/target/target_core_internal.h
@@ -151,6 +151,7 @@ int	transport_dump_vpd_ident(struct t10_vpd *, unsigned char *, int);
 void	transport_clear_lun_ref(struct se_lun *);
 sense_reason_t	target_cmd_size_check(struct se_cmd *cmd, unsigned int size);
 void	target_qf_do_work(struct work_struct *work);
+void	target_do_delayed_work(struct work_struct *work);
 bool	target_check_wce(struct se_device *dev);
 bool	target_check_fua(struct se_device *dev);
 void	__target_execute_cmd(struct se_cmd *, bool);
diff --git a/drivers/target/target_core_transport.c b/drivers/target/target_core_transport.c
index 26ceabe34de55..20fb4905b4568 100644
--- a/drivers/target/target_core_transport.c
+++ b/drivers/target/target_core_transport.c
@@ -2161,32 +2161,35 @@ static bool target_handle_task_attr(struct se_cmd *cmd)
 	 */
 	switch (cmd->sam_task_attr) {
 	case TCM_HEAD_TAG:
+		atomic_inc_mb(&dev->non_ordered);
 		pr_debug("Added HEAD_OF_QUEUE for CDB: 0x%02x\n",
 			 cmd->t_task_cdb[0]);
 		return false;
 	case TCM_ORDERED_TAG:
-		atomic_inc_mb(&dev->dev_ordered_sync);
+		atomic_inc_mb(&dev->delayed_cmd_count);
 
 		pr_debug("Added ORDERED for CDB: 0x%02x to ordered list\n",
 			 cmd->t_task_cdb[0]);
-
-		/*
-		 * Execute an ORDERED command if no other older commands
-		 * exist that need to be completed first.
-		 */
-		if (!atomic_read(&dev->simple_cmds))
-			return false;
 		break;
 	default:
 		/*
 		 * For SIMPLE and UNTAGGED Task Attribute commands
 		 */
-		atomic_inc_mb(&dev->simple_cmds);
+		atomic_inc_mb(&dev->non_ordered);
+
+		if (atomic_read(&dev->delayed_cmd_count) == 0)
+			return false;
 		break;
 	}
 
-	if (atomic_read(&dev->dev_ordered_sync) == 0)
-		return false;
+	if (cmd->sam_task_attr != TCM_ORDERED_TAG) {
+		atomic_inc_mb(&dev->delayed_cmd_count);
+		/*
+		 * We will account for this when we dequeue from the delayed
+		 * list.
+		 */
+		atomic_dec_mb(&dev->non_ordered);
+	}
 
 	spin_lock(&dev->delayed_cmd_lock);
 	list_add_tail(&cmd->se_delayed_node, &dev->delayed_cmd_list);
@@ -2194,6 +2197,12 @@ static bool target_handle_task_attr(struct se_cmd *cmd)
 
 	pr_debug("Added CDB: 0x%02x Task Attr: 0x%02x to delayed CMD listn",
 		cmd->t_task_cdb[0], cmd->sam_task_attr);
+	/*
+	 * We may have no non ordered cmds when this function started or we
+	 * could have raced with the last simple/head cmd completing, so kick
+	 * the delayed handler here.
+	 */
+	schedule_work(&dev->delayed_cmd_work);
 	return true;
 }
 
@@ -2231,29 +2240,48 @@ EXPORT_SYMBOL(target_execute_cmd);
  * Process all commands up to the last received ORDERED task attribute which
  * requires another blocking boundary
  */
-static void target_restart_delayed_cmds(struct se_device *dev)
+void target_do_delayed_work(struct work_struct *work)
 {
-	for (;;) {
+	struct se_device *dev = container_of(work, struct se_device,
+					     delayed_cmd_work);
+
+	spin_lock(&dev->delayed_cmd_lock);
+	while (!dev->ordered_sync_in_progress) {
 		struct se_cmd *cmd;
 
-		spin_lock(&dev->delayed_cmd_lock);
-		if (list_empty(&dev->delayed_cmd_list)) {
-			spin_unlock(&dev->delayed_cmd_lock);
+		if (list_empty(&dev->delayed_cmd_list))
 			break;
-		}
 
 		cmd = list_entry(dev->delayed_cmd_list.next,
 				 struct se_cmd, se_delayed_node);
+
+		if (cmd->sam_task_attr == TCM_ORDERED_TAG) {
+			/*
+			 * Check if we started with:
+			 * [ordered] [simple] [ordered]
+			 * and we are now at the last ordered so we have to wait
+			 * for the simple cmd.
+			 */
+			if (atomic_read(&dev->non_ordered) > 0)
+				break;
+
+			dev->ordered_sync_in_progress = true;
+		}
+
 		list_del(&cmd->se_delayed_node);
+		atomic_dec_mb(&dev->delayed_cmd_count);
 		spin_unlock(&dev->delayed_cmd_lock);
 
+		if (cmd->sam_task_attr != TCM_ORDERED_TAG)
+			atomic_inc_mb(&dev->non_ordered);
+
 		cmd->transport_state |= CMD_T_SENT;
 
 		__target_execute_cmd(cmd, true);
 
-		if (cmd->sam_task_attr == TCM_ORDERED_TAG)
-			break;
+		spin_lock(&dev->delayed_cmd_lock);
 	}
+	spin_unlock(&dev->delayed_cmd_lock);
 }
 
 /*
@@ -2271,14 +2299,17 @@ static void transport_complete_task_attr(struct se_cmd *cmd)
 		goto restart;
 
 	if (cmd->sam_task_attr == TCM_SIMPLE_TAG) {
-		atomic_dec_mb(&dev->simple_cmds);
+		atomic_dec_mb(&dev->non_ordered);
 		dev->dev_cur_ordered_id++;
 	} else if (cmd->sam_task_attr == TCM_HEAD_TAG) {
+		atomic_dec_mb(&dev->non_ordered);
 		dev->dev_cur_ordered_id++;
 		pr_debug("Incremented dev_cur_ordered_id: %u for HEAD_OF_QUEUE\n",
 			 dev->dev_cur_ordered_id);
 	} else if (cmd->sam_task_attr == TCM_ORDERED_TAG) {
-		atomic_dec_mb(&dev->dev_ordered_sync);
+		spin_lock(&dev->delayed_cmd_lock);
+		dev->ordered_sync_in_progress = false;
+		spin_unlock(&dev->delayed_cmd_lock);
 
 		dev->dev_cur_ordered_id++;
 		pr_debug("Incremented dev_cur_ordered_id: %u for ORDERED\n",
@@ -2287,7 +2318,8 @@ static void transport_complete_task_attr(struct se_cmd *cmd)
 	cmd->se_cmd_flags &= ~SCF_TASK_ATTR_SET;
 
 restart:
-	target_restart_delayed_cmds(dev);
+	if (atomic_read(&dev->delayed_cmd_count) > 0)
+		schedule_work(&dev->delayed_cmd_work);
 }
 
 static void transport_complete_qf(struct se_cmd *cmd)
diff --git a/include/target/target_core_base.h b/include/target/target_core_base.h
index 85c16c266eac7..3ccd11a153975 100644
--- a/include/target/target_core_base.h
+++ b/include/target/target_core_base.h
@@ -808,8 +808,9 @@ struct se_device {
 	atomic_long_t		read_bytes;
 	atomic_long_t		write_bytes;
 	/* Active commands on this virtual SE device */
-	atomic_t		simple_cmds;
-	atomic_t		dev_ordered_sync;
+	atomic_t		non_ordered;
+	bool			ordered_sync_in_progress;
+	atomic_t		delayed_cmd_count;
 	atomic_t		dev_qf_count;
 	u32			export_count;
 	spinlock_t		delayed_cmd_lock;
@@ -830,6 +831,7 @@ struct se_device {
 	struct list_head	dev_sep_list;
 	struct list_head	dev_tmr_list;
 	struct work_struct	qf_work_queue;
+	struct work_struct	delayed_cmd_work;
 	struct list_head	delayed_cmd_list;
 	struct list_head	qf_cmd_list;
 	/* Pointer to associated SE HBA */
-- 
2.33.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.14 68/75] arm64: dts: qcom: msm8916: Add CPU ACC and SAW/SPM

[Sasha Levin]

From: Stephan Gerhold <stephan@gerhold.net>

[ Upstream commit a22f9a766e1dc61f8f6ee2edfe83d4d23d78e059 ]

Add the device tree nodes necessary for SMP bring-up and cpuidle
without PSCI on ARM32. The hardware is typically controlled by the
PSCI implementation in the TrustZone firmware and is therefore marked
as status = "reserved" by default (from the device tree specification):

  "Indicates that the device is operational, but should not be used.
   Typically this is used for devices that are controlled by another
   software component, such as platform firmware."

Since this is part of the MSM8916 SoC it should be added to msm8916.dtsi
but in practice these nodes should only get enabled via an extra include
on ARM32.

This is necessary for some devices with signed firmware which is missing
both ARM64 and PSCI support and can therefore only boot ARM32 kernels.

Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211004204955.21077-13-stephan@gerhold.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/qcom/msm8916.dtsi | 56 +++++++++++++++++++++++++++
 1 file changed, 56 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
index fa26d3871e00a..3c303ce492fcb 100644
--- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
@@ -124,6 +124,8 @@
 			#cooling-cells = <2>;
 			power-domains = <&CPU_PD0>;
 			power-domain-names = "psci";
+			qcom,acc = <&cpu0_acc>;
+			qcom,saw = <&cpu0_saw>;
 		};
 
 		CPU1: cpu@1 {
@@ -137,6 +139,8 @@
 			#cooling-cells = <2>;
 			power-domains = <&CPU_PD1>;
 			power-domain-names = "psci";
+			qcom,acc = <&cpu1_acc>;
+			qcom,saw = <&cpu1_saw>;
 		};
 
 		CPU2: cpu@2 {
@@ -150,6 +154,8 @@
 			#cooling-cells = <2>;
 			power-domains = <&CPU_PD2>;
 			power-domain-names = "psci";
+			qcom,acc = <&cpu2_acc>;
+			qcom,saw = <&cpu2_saw>;
 		};
 
 		CPU3: cpu@3 {
@@ -163,6 +169,8 @@
 			#cooling-cells = <2>;
 			power-domains = <&CPU_PD3>;
 			power-domain-names = "psci";
+			qcom,acc = <&cpu3_acc>;
+			qcom,saw = <&cpu3_saw>;
 		};
 
 		L2_0: l2-cache {
@@ -1844,6 +1852,54 @@
 				status = "disabled";
 			};
 		};
+
+		cpu0_acc: power-manager@b088000 {
+			compatible = "qcom,msm8916-acc";
+			reg = <0x0b088000 0x1000>;
+			status = "reserved"; /* Controlled by PSCI firmware */
+		};
+
+		cpu0_saw: power-manager@b089000 {
+			compatible = "qcom,msm8916-saw2-v3.0-cpu", "qcom,saw2";
+			reg = <0x0b089000 0x1000>;
+			status = "reserved"; /* Controlled by PSCI firmware */
+		};
+
+		cpu1_acc: power-manager@b098000 {
+			compatible = "qcom,msm8916-acc";
+			reg = <0x0b098000 0x1000>;
+			status = "reserved"; /* Controlled by PSCI firmware */
+		};
+
+		cpu1_saw: power-manager@b099000 {
+			compatible = "qcom,msm8916-saw2-v3.0-cpu", "qcom,saw2";
+			reg = <0x0b099000 0x1000>;
+			status = "reserved"; /* Controlled by PSCI firmware */
+		};
+
+		cpu2_acc: power-manager@b0a8000 {
+			compatible = "qcom,msm8916-acc";
+			reg = <0x0b0a8000 0x1000>;
+			status = "reserved"; /* Controlled by PSCI firmware */
+		};
+
+		cpu2_saw: power-manager@b0a9000 {
+			compatible = "qcom,msm8916-saw2-v3.0-cpu", "qcom,saw2";
+			reg = <0x0b0a9000 0x1000>;
+			status = "reserved"; /* Controlled by PSCI firmware */
+		};
+
+		cpu3_acc: power-manager@b0b8000 {
+			compatible = "qcom,msm8916-acc";
+			reg = <0x0b0b8000 0x1000>;
+			status = "reserved"; /* Controlled by PSCI firmware */
+		};
+
+		cpu3_saw: power-manager@b0b9000 {
+			compatible = "qcom,msm8916-saw2-v3.0-cpu", "qcom,saw2";
+			reg = <0x0b0b9000 0x1000>;
+			status = "reserved"; /* Controlled by PSCI firmware */
+		};
 	};
 
 	thermal-zones {
-- 
2.33.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.14 69/75] ARM: dts: qcom: fix memory and mdio nodes naming for RB3011

[Sasha Levin]

From: David Heidelberg <david@ixit.cz>

[ Upstream commit 14a1f6c9d8017ffbf388e82e1a1f023196d98612 ]

Fixes warnings regarding to memory and mdio nodes and
apply new naming following dt-schema.

Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211020214741.261509-1-david@ixit.cz
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/qcom-ipq8064-rb3011.dts | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts b/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts
index f7ea2e5dd1914..971d2e2292600 100644
--- a/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts
+++ b/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts
@@ -19,12 +19,12 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	memory@0 {
+	memory@42000000 {
 		reg = <0x42000000 0x3e000000>;
 		device_type = "memory";
 	};
 
-	mdio0: mdio@0 {
+	mdio0: mdio-0 {
 		status = "okay";
 		compatible = "virtual,mdio-gpio";
 		gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>,
@@ -91,7 +91,7 @@
 		};
 	};
 
-	mdio1: mdio@1 {
+	mdio1: mdio-1 {
 		status = "okay";
 		compatible = "virtual,mdio-gpio";
 		gpios = <&qcom_pinmux 11 GPIO_ACTIVE_HIGH>,
-- 
2.33.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel