* [linux][PATCH 0/6] Add support for sam9x60 curiosity board
@ 2022-09-07 9:20 Hari Prasath
2022-09-07 9:20 ` [linux][PATCH 1/6] ARM: dts: at91: sam9x60: Fix the label numbering for the flexcom functions Hari Prasath
` (5 more replies)
0 siblings, 6 replies; 12+ messages in thread
From: Hari Prasath @ 2022-09-07 9:20 UTC (permalink / raw)
To: nicolas.ferre, claudiu.beznea, davem, krzysztof.kozlowski+dt,
alexandre.belloni, arnd, olof, soc, manikandan.m, michael,
horatiu.vultur, kavyasree.kotagiri, devicetree, linux-arm-kernel,
linux-kernel, durai.manickamkr
Cc: Hari.PrasathGE
This patch series addresses the following:
- Moving of flexcom definitions from board file to SoC file plus
some minor changes to its properties.
- Add support for the new sam9x60 curiosity board based on the
existing sam9x60 SoC.
Durai Manickam KR (1):
ARM: dts: at91: sam9x60: Add missing flexcom definitions
Hari Prasath (2):
ARM: dts: at91: sam9x60: Move flexcom definitions to the SoC dtsi
ARM: dts: at91: sam9x60: Add DMA bindigs for the flexcom nodes
Manikandan M (3):
ARM: dts: at91: sam9x60: Fix the label numbering for the flexcom
functions
ARM: dts: at91: sam9x60: Specify the FIFO size for the Flexcom UART
ARM: dts: at91: sam9x60_curiosity: Add device tree for
sam9x60_curiosity board
.../devicetree/bindings/arm/atmel-at91.yaml | 6 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/at91-sam9x60_curiosity.dts | 532 +++++++++++++++
arch/arm/boot/dts/at91-sam9x60ek.dts | 49 +-
arch/arm/boot/dts/sam9x60.dtsi | 623 ++++++++++++++++++
5 files changed, 1172 insertions(+), 39 deletions(-)
create mode 100644 arch/arm/boot/dts/at91-sam9x60_curiosity.dts
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 12+ messages in thread
* [linux][PATCH 1/6] ARM: dts: at91: sam9x60: Fix the label numbering for the flexcom functions
2022-09-07 9:20 [linux][PATCH 0/6] Add support for sam9x60 curiosity board Hari Prasath
@ 2022-09-07 9:20 ` Hari Prasath
2022-09-07 9:20 ` [linux][PATCH 2/6] ARM: dts: at91: sam9x60: Move flexcom definitions to the SoC dtsi Hari Prasath
` (4 subsequent siblings)
5 siblings, 0 replies; 12+ messages in thread
From: Hari Prasath @ 2022-09-07 9:20 UTC (permalink / raw)
To: nicolas.ferre, claudiu.beznea, davem, krzysztof.kozlowski+dt,
alexandre.belloni, arnd, olof, soc, manikandan.m, michael,
horatiu.vultur, kavyasree.kotagiri, devicetree, linux-arm-kernel,
linux-kernel, durai.manickamkr
Cc: Hari.PrasathGE
From: Manikandan M <manikandan.m@microchip.com>
Fixed the label numbering of the flexcom functions so that all
13 flexcom functions of sam9x60 are in the following order when the missing
flexcom functions are added:
flx0: uart0, spi0, i2c0
flx1: uart1, spi1, i2c1
flx2: uart2, spi2, i2c2
flx3: uart3, spi3, i2c3
flx4: uart4, spi4, i2c4
flx5: uart5, spi5, i2c5
flx6: uart6, i2c6
flx7: uart7, i2c7
flx8: uart8, i2c8
flx9: uart9, i2c9
flx10: uart10, i2c10
flx11: uart11, i2c11
flx12: uart12, i2c12
Signed-off-by: Manikandan M <manikandan.m@microchip.com>
---
arch/arm/boot/dts/at91-sam9x60ek.dts | 12 ++++++------
1 file changed, 6 insertions(+), 6 deletions(-)
diff --git a/arch/arm/boot/dts/at91-sam9x60ek.dts b/arch/arm/boot/dts/at91-sam9x60ek.dts
index 7ade9979e1c6..b9b7a235ef89 100644
--- a/arch/arm/boot/dts/at91-sam9x60ek.dts
+++ b/arch/arm/boot/dts/at91-sam9x60ek.dts
@@ -16,8 +16,8 @@
aliases {
i2c0 = &i2c0;
- i2c1 = &i2c1;
- serial1 = &uart1;
+ i2c1 = &i2c6;
+ serial1 = &uart5;
};
chosen {
@@ -238,7 +238,7 @@
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>;
status = "disabled";
- spi0: spi@400 {
+ spi4: spi@400 {
compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
reg = <0x400 0x200>;
interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -257,7 +257,7 @@
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
status = "okay";
- uart1: serial@200 {
+ uart5: serial@200 {
compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -282,7 +282,7 @@
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
status = "okay";
- i2c1: i2c@600 {
+ i2c6: i2c@600 {
compatible = "microchip,sam9x60-i2c";
reg = <0x600 0x200>;
interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -442,7 +442,7 @@
AT91_PIOA 14 AT91_PERIPH_A AT91_PINCTRL_NONE>;
};
- pinctrl_flx5_default: flx_uart {
+ pinctrl_flx5_default: flx5_uart {
atmel,pins =
<AT91_PIOA 7 AT91_PERIPH_C AT91_PINCTRL_NONE
AT91_PIOA 8 AT91_PERIPH_B AT91_PINCTRL_NONE
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [linux][PATCH 2/6] ARM: dts: at91: sam9x60: Move flexcom definitions to the SoC dtsi
2022-09-07 9:20 [linux][PATCH 0/6] Add support for sam9x60 curiosity board Hari Prasath
2022-09-07 9:20 ` [linux][PATCH 1/6] ARM: dts: at91: sam9x60: Fix the label numbering for the flexcom functions Hari Prasath
@ 2022-09-07 9:20 ` Hari Prasath
2022-09-08 7:59 ` Claudiu.Beznea
2022-09-07 9:20 ` [linux][PATCH 3/6] ARM: dts: at91: sam9x60: Specify the FIFO size for the Flexcom UART Hari Prasath
` (3 subsequent siblings)
5 siblings, 1 reply; 12+ messages in thread
From: Hari Prasath @ 2022-09-07 9:20 UTC (permalink / raw)
To: nicolas.ferre, claudiu.beznea, davem, krzysztof.kozlowski+dt,
alexandre.belloni, arnd, olof, soc, manikandan.m, michael,
horatiu.vultur, kavyasree.kotagiri, devicetree, linux-arm-kernel,
linux-kernel, durai.manickamkr
Cc: Hari.PrasathGE
Move the flexcom definitions to the SoC specifc DTSI file retaining only
the pinmux and desired functions in the board specific DTS file of
sam9x60ek.
Signed-off-by: Hari Prasath <Hari.PrasathGE@microchip.com>
Signed-off-by: Manikandan M <manikandan.m@microchip.com>
Signed-off-by: Durai Manickam KR <durai.manickamkr@microchip.com>
---
arch/arm/boot/dts/at91-sam9x60ek.dts | 34 +-----------------
arch/arm/boot/dts/sam9x60.dtsi | 52 ++++++++++++++++++++++++++--
2 files changed, 51 insertions(+), 35 deletions(-)
diff --git a/arch/arm/boot/dts/at91-sam9x60ek.dts b/arch/arm/boot/dts/at91-sam9x60ek.dts
index b9b7a235ef89..9d9e50c77794 100644
--- a/arch/arm/boot/dts/at91-sam9x60ek.dts
+++ b/arch/arm/boot/dts/at91-sam9x60ek.dts
@@ -211,15 +211,10 @@
status = "okay";
i2c0: i2c@600 {
- compatible = "microchip,sam9x60-i2c";
- reg = <0x600 0x200>;
- interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
#address-cells = <1>;
#size-cells = <0>;
- clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flx0_default>;
- atmel,fifo-size = <16>;
i2c-analog-filter;
i2c-digital-filter;
i2c-digital-filter-width-ns = <35>;
@@ -239,16 +234,8 @@
status = "disabled";
spi4: spi@400 {
- compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
- reg = <0x400 0x200>;
- interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
- clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
- clock-names = "spi_clk";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flx4_default>;
- atmel,fifo-size = <16>;
- #address-cells = <1>;
- #size-cells = <0>;
status = "disabled";
};
};
@@ -258,22 +245,8 @@
status = "okay";
uart5: serial@200 {
- compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
- reg = <0x200 0x200>;
- interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
- dmas = <&dma0
- (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
- AT91_XDMAC_DT_PERID(10))>,
- <&dma0
- (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
- AT91_XDMAC_DT_PERID(11))>;
- dma-names = "tx", "rx";
- clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
- clock-names = "usart";
- pinctrl-0 = <&pinctrl_flx5_default>;
pinctrl-names = "default";
- atmel,use-dma-rx;
- atmel,use-dma-tx;
+ pinctrl-0 = <&pinctrl_flx5_default>;
status = "okay";
};
};
@@ -283,15 +256,10 @@
status = "okay";
i2c6: i2c@600 {
- compatible = "microchip,sam9x60-i2c";
- reg = <0x600 0x200>;
- interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
#address-cells = <1>;
#size-cells = <0>;
- clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flx6_default>;
- atmel,fifo-size = <16>;
i2c-analog-filter;
i2c-digital-filter;
i2c-digital-filter-width-ns = <35>;
diff --git a/arch/arm/boot/dts/sam9x60.dtsi b/arch/arm/boot/dts/sam9x60.dtsi
index d3f60f6a456d..f0e0dc20de1b 100644
--- a/arch/arm/boot/dts/sam9x60.dtsi
+++ b/arch/arm/boot/dts/sam9x60.dtsi
@@ -169,6 +169,16 @@
#size-cells = <1>;
ranges = <0x0 0xf0000000 0x800>;
status = "disabled";
+
+ spi4: spi@400 {
+ compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
+ clock-names = "spi_clk";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
};
flx5: flexcom@f0004000 {
@@ -179,6 +189,26 @@
#size-cells = <1>;
ranges = <0x0 0xf0004000 0x800>;
status = "disabled";
+
+ uart5: serial@200 {
+ compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(10))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(11))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ status = "disabled";
+ };
};
dma0: dma-controller@f0008000 {
@@ -378,6 +408,15 @@
#size-cells = <1>;
ranges = <0x0 0xf8010000 0x800>;
status = "disabled";
+
+ i2c6: i2c@600 {
+ compatible = "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
};
flx7: flexcom@f8014000 {
@@ -404,10 +443,19 @@
compatible = "atmel,sama5d2-flexcom";
reg = <0xf801c000 0x200>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
- #address-cells = <1>;
- #size-cells = <1>;
ranges = <0x0 0xf801c000 0x800>;
status = "disabled";
+
+ i2c0: i2c@600 {
+ compatible = "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
};
flx1: flexcom@f8020000 {
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [linux][PATCH 3/6] ARM: dts: at91: sam9x60: Specify the FIFO size for the Flexcom UART
2022-09-07 9:20 [linux][PATCH 0/6] Add support for sam9x60 curiosity board Hari Prasath
2022-09-07 9:20 ` [linux][PATCH 1/6] ARM: dts: at91: sam9x60: Fix the label numbering for the flexcom functions Hari Prasath
2022-09-07 9:20 ` [linux][PATCH 2/6] ARM: dts: at91: sam9x60: Move flexcom definitions to the SoC dtsi Hari Prasath
@ 2022-09-07 9:20 ` Hari Prasath
2022-09-07 9:20 ` [linux][PATCH 4/6] ARM: dts: at91: sam9x60: Add DMA bindigs for the flexcom nodes Hari Prasath
` (2 subsequent siblings)
5 siblings, 0 replies; 12+ messages in thread
From: Hari Prasath @ 2022-09-07 9:20 UTC (permalink / raw)
To: nicolas.ferre, claudiu.beznea, davem, krzysztof.kozlowski+dt,
alexandre.belloni, arnd, olof, soc, manikandan.m, michael,
horatiu.vultur, kavyasree.kotagiri, devicetree, linux-arm-kernel,
linux-kernel, durai.manickamkr
Cc: Hari.PrasathGE
From: Manikandan M <manikandan.m@microchip.com>
The UART submodule in Flexcom has 16-byte Transmit and Receive FIFOs.
Signed-off-by: Manikandan M <manikandan.m@microchip.com>
---
arch/arm/boot/dts/sam9x60.dtsi | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm/boot/dts/sam9x60.dtsi b/arch/arm/boot/dts/sam9x60.dtsi
index f0e0dc20de1b..224b406c8384 100644
--- a/arch/arm/boot/dts/sam9x60.dtsi
+++ b/arch/arm/boot/dts/sam9x60.dtsi
@@ -207,6 +207,7 @@
clock-names = "usart";
atmel,use-dma-rx;
atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
status = "disabled";
};
};
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [linux][PATCH 4/6] ARM: dts: at91: sam9x60: Add DMA bindigs for the flexcom nodes
2022-09-07 9:20 [linux][PATCH 0/6] Add support for sam9x60 curiosity board Hari Prasath
` (2 preceding siblings ...)
2022-09-07 9:20 ` [linux][PATCH 3/6] ARM: dts: at91: sam9x60: Specify the FIFO size for the Flexcom UART Hari Prasath
@ 2022-09-07 9:20 ` Hari Prasath
2022-09-08 7:58 ` Claudiu.Beznea
2022-09-07 9:20 ` [linux][PATCH 5/6] ARM: dts: at91: sam9x60: Add missing flexcom definitions Hari Prasath
2022-09-07 9:20 ` [linux][PATCH 6/6] ARM: dts: at91: sam9x60_curiosity: Add device tree for sam9x60_curiosity board Hari Prasath
5 siblings, 1 reply; 12+ messages in thread
From: Hari Prasath @ 2022-09-07 9:20 UTC (permalink / raw)
To: nicolas.ferre, claudiu.beznea, davem, krzysztof.kozlowski+dt,
alexandre.belloni, arnd, olof, soc, manikandan.m, michael,
horatiu.vultur, kavyasree.kotagiri, devicetree, linux-arm-kernel,
linux-kernel, durai.manickamkr
Cc: Hari.PrasathGE
Add dma bindings for flexcom nodes in the soc dtsi file. Users those who
don't wish to use the DMA function for their flexcom functions can
overwrite the dma bindings in the board device tree file.
Signed-off-by: Manikandan M <manikandan.m@microchip.com>
Signed-off-by: Hari Prasath <Hari.PrasathGE@microchip.com>
---
arch/arm/boot/dts/at91-sam9x60ek.dts | 3 +++
arch/arm/boot/dts/sam9x60.dtsi | 27 +++++++++++++++++++++++++++
2 files changed, 30 insertions(+)
diff --git a/arch/arm/boot/dts/at91-sam9x60ek.dts b/arch/arm/boot/dts/at91-sam9x60ek.dts
index 9d9e50c77794..9ad528e1bdd2 100644
--- a/arch/arm/boot/dts/at91-sam9x60ek.dts
+++ b/arch/arm/boot/dts/at91-sam9x60ek.dts
@@ -213,6 +213,7 @@
i2c0: i2c@600 {
#address-cells = <1>;
#size-cells = <0>;
+ dmas = <0>, <0>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flx0_default>;
i2c-analog-filter;
@@ -234,6 +235,7 @@
status = "disabled";
spi4: spi@400 {
+ dmas = <0>, <0>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flx4_default>;
status = "disabled";
@@ -258,6 +260,7 @@
i2c6: i2c@600 {
#address-cells = <1>;
#size-cells = <0>;
+ dmas = <0>, <0>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flx6_default>;
i2c-analog-filter;
diff --git a/arch/arm/boot/dts/sam9x60.dtsi b/arch/arm/boot/dts/sam9x60.dtsi
index 224b406c8384..feeabc53e0ec 100644
--- a/arch/arm/boot/dts/sam9x60.dtsi
+++ b/arch/arm/boot/dts/sam9x60.dtsi
@@ -176,6 +176,15 @@
interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
clock-names = "spi_clk";
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(8))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(9))>;
+ dma-names = "tx", "rx";
atmel,fifo-size = <16>;
status = "disabled";
};
@@ -415,6 +424,15 @@
reg = <0x600 0x200>;
interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(12))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(13))>;
+ dma-names = "tx", "rx";
atmel,fifo-size = <16>;
status = "disabled";
};
@@ -454,6 +472,15 @@
#address-cells = <1>;
#size-cells = <0>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(0))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(1))>;
+ dma-names = "tx", "rx";
atmel,fifo-size = <16>;
status = "disabled";
};
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [linux][PATCH 5/6] ARM: dts: at91: sam9x60: Add missing flexcom definitions
2022-09-07 9:20 [linux][PATCH 0/6] Add support for sam9x60 curiosity board Hari Prasath
` (3 preceding siblings ...)
2022-09-07 9:20 ` [linux][PATCH 4/6] ARM: dts: at91: sam9x60: Add DMA bindigs for the flexcom nodes Hari Prasath
@ 2022-09-07 9:20 ` Hari Prasath
2022-09-08 7:58 ` Claudiu.Beznea
2022-09-07 9:20 ` [linux][PATCH 6/6] ARM: dts: at91: sam9x60_curiosity: Add device tree for sam9x60_curiosity board Hari Prasath
5 siblings, 1 reply; 12+ messages in thread
From: Hari Prasath @ 2022-09-07 9:20 UTC (permalink / raw)
To: nicolas.ferre, claudiu.beznea, davem, krzysztof.kozlowski+dt,
alexandre.belloni, arnd, olof, soc, manikandan.m, michael,
horatiu.vultur, kavyasree.kotagiri, devicetree, linux-arm-kernel,
linux-kernel, durai.manickamkr
Cc: Hari.PrasathGE
From: Durai Manickam KR <durai.manickamkr@microchip.com>
Added the missing flexcom functions for all the flexcom nodes.
Signed-off-by: Manikandan M <manikandan.m@microchip.com>
Signed-off-by: Durai Manickam KR <durai.manickamkr@microchip.com>
Signed-off-by: Hari Prasath <Hari.PrasathGE@microchip.com>
---
arch/arm/boot/dts/sam9x60.dtsi | 547 +++++++++++++++++++++++++++++++++
1 file changed, 547 insertions(+)
diff --git a/arch/arm/boot/dts/sam9x60.dtsi b/arch/arm/boot/dts/sam9x60.dtsi
index feeabc53e0ec..1c580c3ba7c3 100644
--- a/arch/arm/boot/dts/sam9x60.dtsi
+++ b/arch/arm/boot/dts/sam9x60.dtsi
@@ -170,6 +170,27 @@
ranges = <0x0 0xf0000000 0x800>;
status = "disabled";
+ uart4: serial@200 {
+ compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(8))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(9))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
spi4: spi@400 {
compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
reg = <0x400 0x200>;
@@ -188,6 +209,24 @@
atmel,fifo-size = <16>;
status = "disabled";
};
+
+ i2c4: i2c@600 {
+ compatible = "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(8))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(9))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
};
flx5: flexcom@f0004000 {
@@ -219,6 +258,43 @@
atmel,fifo-size = <16>;
status = "disabled";
};
+
+ spi5: spi@400 {
+ compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
+ clock-names = "spi_clk";
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(10))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(11))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c5: i2c@600 {
+ compatible = "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(10))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(11))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
};
dma0: dma-controller@f0008000 {
@@ -290,6 +366,45 @@
#size-cells = <1>;
ranges = <0x0 0xf0020000 0x800>;
status = "disabled";
+
+ uart11: serial@200 {
+ compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <32 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(22))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(23))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 32>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c11: i2c@600 {
+ compatible = "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <32 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 32>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(22))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(23))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
};
flx12: flexcom@f0024000 {
@@ -300,6 +415,45 @@
#size-cells = <1>;
ranges = <0x0 0xf0024000 0x800>;
status = "disabled";
+
+ uart12: serial@200 {
+ compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <33 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(24))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(25))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 33>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c12: i2c@600 {
+ compatible = "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <33 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 33>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(24))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(25))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
};
pit64b: timer@f0028000 {
@@ -419,6 +573,27 @@
ranges = <0x0 0xf8010000 0x800>;
status = "disabled";
+ uart6: serial@200 {
+ compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(12))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(13))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
i2c6: i2c@600 {
compatible = "microchip,sam9x60-i2c";
reg = <0x600 0x200>;
@@ -446,6 +621,45 @@
#size-cells = <1>;
ranges = <0x0 0xf8014000 0x800>;
status = "disabled";
+
+ uart7: serial@200 {
+ compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <10 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(14))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(15))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c7: i2c@600 {
+ compatible = "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <10 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(14))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(15))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
};
flx8: flexcom@f8018000 {
@@ -456,15 +670,96 @@
#size-cells = <1>;
ranges = <0x0 0xf8018000 0x800>;
status = "disabled";
+
+ uart8: serial@200 {
+ compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <11 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(16))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(17))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c8: i2c@600 {
+ compatible = "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <11 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(16))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(17))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
};
flx0: flexcom@f801c000 {
compatible = "atmel,sama5d2-flexcom";
reg = <0xf801c000 0x200>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+ #address-cells = <1>;
+ #size-cells = <1>;
ranges = <0x0 0xf801c000 0x800>;
status = "disabled";
+ uart0: serial@200 {
+ compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(0))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(1))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ spi0: spi@400 {
+ compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+ clock-names = "spi_clk";
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(0))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(1))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
i2c0: i2c@600 {
compatible = "microchip,sam9x60-i2c";
reg = <0x600 0x200>;
@@ -494,6 +789,64 @@
#size-cells = <1>;
ranges = <0x0 0xf8020000 0x800>;
status = "disabled";
+
+ uart1: serial@200 {
+ compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(2))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(3))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ spi1: spi@400 {
+ compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
+ clock-names = "spi_clk";
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(2))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(3))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c1: i2c@600 {
+ compatible = "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(2))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(3))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
};
flx2: flexcom@f8024000 {
@@ -504,6 +857,64 @@
#size-cells = <1>;
ranges = <0x0 0xf8024000 0x800>;
status = "disabled";
+
+ uart2: serial@200 {
+ compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(4))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(5))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ spi2: spi@400 {
+ compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
+ clock-names = "spi_clk";
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(4))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(5))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c2: i2c@600 {
+ compatible = "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(4))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(5))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
};
flx3: flexcom@f8028000 {
@@ -514,6 +925,64 @@
#size-cells = <1>;
ranges = <0x0 0xf8028000 0x800>;
status = "disabled";
+
+ uart3: serial@200 {
+ compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(6))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(7))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ spi3: spi@400 {
+ compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
+ clock-names = "spi_clk";
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(6))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(7))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c3: i2c@600 {
+ compatible = "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(6))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(7))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
};
macb0: ethernet@f802c000 {
@@ -579,6 +1048,45 @@
#size-cells = <1>;
ranges = <0x0 0xf8040000 0x800>;
status = "disabled";
+
+ uart9: serial@200 {
+ compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <15 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(18))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(19))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c9: i2c@600 {
+ compatible = "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <15 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(18))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(19))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
};
flx10: flexcom@f8044000 {
@@ -589,6 +1097,45 @@
#size-cells = <1>;
ranges = <0x0 0xf8044000 0x800>;
status = "disabled";
+
+ uart10: serial@200 {
+ compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <16 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(20))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(21))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 16>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c10: i2c@600 {
+ compatible = "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <16 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 16>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(20))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(21))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
};
isi: isi@f8048000 {
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [linux][PATCH 6/6] ARM: dts: at91: sam9x60_curiosity: Add device tree for sam9x60_curiosity board
2022-09-07 9:20 [linux][PATCH 0/6] Add support for sam9x60 curiosity board Hari Prasath
` (4 preceding siblings ...)
2022-09-07 9:20 ` [linux][PATCH 5/6] ARM: dts: at91: sam9x60: Add missing flexcom definitions Hari Prasath
@ 2022-09-07 9:20 ` Hari Prasath
2022-09-08 7:58 ` Claudiu.Beznea
2022-09-08 11:04 ` Krzysztof Kozlowski
5 siblings, 2 replies; 12+ messages in thread
From: Hari Prasath @ 2022-09-07 9:20 UTC (permalink / raw)
To: nicolas.ferre, claudiu.beznea, davem, krzysztof.kozlowski+dt,
alexandre.belloni, arnd, olof, soc, manikandan.m, michael,
horatiu.vultur, kavyasree.kotagiri, devicetree, linux-arm-kernel,
linux-kernel, durai.manickamkr
Cc: Hari.PrasathGE
From: Manikandan M <manikandan.m@microchip.com>
Add device tree file for sam9x60_curiosity board.
Signed-off-by: Durai Manickam KR <durai.manickamkr@microchip.com>
Signed-off-by: Manikandan M <manikandan.m@microchip.com>
Signed-off-by: Hari Prasath <Hari.PrasathGE@microchip.com>
---
.../devicetree/bindings/arm/atmel-at91.yaml | 6 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/at91-sam9x60_curiosity.dts | 532 ++++++++++++++++++
3 files changed, 539 insertions(+)
create mode 100644 arch/arm/boot/dts/at91-sam9x60_curiosity.dts
diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.yaml b/Documentation/devicetree/bindings/arm/atmel-at91.yaml
index 2b7848bb7769..fae3a3090fbd 100644
--- a/Documentation/devicetree/bindings/arm/atmel-at91.yaml
+++ b/Documentation/devicetree/bindings/arm/atmel-at91.yaml
@@ -97,6 +97,12 @@ properties:
- const: microchip,sam9x60
- const: atmel,at91sam9
+ - description: SAM9X60 Curiosity board
+ items:
+ - const: microchip,sam9x60-curiosity
+ - const: microchip,sam9x60
+ - const: atmel,at91sam9
+
- description: Nattis v2 board with Natte v2 power board
items:
- const: axentia,nattis-2
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 595e870750cd..cd60cda5d187 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -51,6 +51,7 @@ dtb-$(CONFIG_SOC_AT91SAM9) += \
at91sam9x25ek.dtb \
at91sam9x35ek.dtb
dtb-$(CONFIG_SOC_SAM9X60) += \
+ at91-sam9x60_curiosity.dtb \
at91-sam9x60ek.dtb
dtb-$(CONFIG_SOC_SAM_V7) += \
at91-kizbox2-2.dtb \
diff --git a/arch/arm/boot/dts/at91-sam9x60_curiosity.dts b/arch/arm/boot/dts/at91-sam9x60_curiosity.dts
new file mode 100644
index 000000000000..75e6727b5e3a
--- /dev/null
+++ b/arch/arm/boot/dts/at91-sam9x60_curiosity.dts
@@ -0,0 +1,532 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * at91-sam9x60_curiosity.dts - Device Tree file for Microchip SAM9X60 CURIOSITY board
+ *
+ * Copyright (C) 2022 Microchip Technology Inc. and its subsidiaries
+ *
+ * Author: Manikandan M <manikandan.m@microchip.com>
+ */
+/dts-v1/;
+#include "sam9x60.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Microchip SAM9X60 CURIOSITY";
+ compatible = "microchip,sam9x60-curiosity", "microchip,sam9x60", "atmel,at91sam9";
+
+ aliases {
+ i2c0 = &i2c0;
+ i2c1 = &i2c6;
+ serial2 = &uart7;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@20000000 {
+ reg = <0x20000000 0x8000000>;
+ };
+
+ clocks {
+ slow_xtal {
+ clock-frequency = <32768>;
+ };
+
+ main_xtal {
+ clock-frequency = <24000000>;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_key_gpio_default>;
+ status = "okay";
+
+ button-user {
+ label = "PB_USER";
+ gpios = <&pioA 29 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_PROG1>;
+ wakeup-source;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_leds>;
+ status = "okay";
+
+ red {
+ label = "red";
+ gpios = <&pioD 17 GPIO_ACTIVE_HIGH>;
+ };
+
+ green {
+ label = "green";
+ gpios = <&pioD 19 GPIO_ACTIVE_HIGH>;
+ };
+
+ blue {
+ label = "blue";
+ gpios = <&pioD 21 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ regulators: regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ vdd_1v8: fixed-regulator-vdd_1v8@0 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDD_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ status = "okay";
+ };
+
+ vdd_1v15: fixed-regulator-vdd_1v15@1 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDD_1V15";
+ regulator-min-microvolt = <1150000>;
+ regulator-max-microvolt = <1150000>;
+ regulator-always-on;
+ status = "okay";
+ };
+
+ vdd1_3v3: fixed-regulator-vdd1_3v3@2 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDD1_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ status = "okay";
+ };
+ };
+};
+
+&adc {
+ vddana-supply = <&vdd1_3v3>;
+ vref-supply = <&vdd1_3v3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_adc_default &pinctrl_adtrg_default>;
+ status = "okay";
+};
+
+&can0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can0_rx_tx>;
+ status = "disabled"; /* Conflict with dbgu. */
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can1_rx_tx>;
+ status = "okay";
+};
+
+&dbgu {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_dbgu>;
+ status = "okay"; /* Conflict with can0. */
+};
+
+&ebi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ebi_addr_nand &pinctrl_ebi_data_0_7>;
+ status = "okay";
+
+ nand_controller: nand-controller {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_nand_oe_we &pinctrl_nand_cs &pinctrl_nand_rb>;
+ status = "okay";
+
+ nand@3 {
+ reg = <0x3 0x0 0x800000>;
+ rb-gpios = <&pioD 5 GPIO_ACTIVE_HIGH>;
+ cs-gpios = <&pioD 4 GPIO_ACTIVE_HIGH>;
+ nand-bus-width = <8>;
+ nand-ecc-mode = "hw";
+ nand-ecc-strength = <8>;
+ nand-ecc-step-size = <512>;
+ nand-on-flash-bbt;
+ label = "atmel_nand";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ at91bootstrap@0 {
+ label = "at91bootstrap";
+ reg = <0x0 0x40000>;
+ };
+
+ uboot@40000 {
+ label = "u-boot";
+ reg = <0x40000 0xc0000>;
+ };
+
+ ubootenvred@100000 {
+ label = "U-Boot Env Redundant";
+ reg = <0x100000 0x40000>;
+ };
+
+ ubootenv@140000 {
+ label = "U-Boot Env";
+ reg = <0x140000 0x40000>;
+ };
+
+ dtb@180000 {
+ label = "device tree";
+ reg = <0x180000 0x80000>;
+ };
+
+ kernel@200000 {
+ label = "kernel";
+ reg = <0x200000 0x600000>;
+ };
+
+ rootfs@800000 {
+ label = "rootfs";
+ reg = <0x800000 0x1f800000>;
+ };
+ };
+ };
+ };
+};
+
+&flx0 {
+ atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+ status = "okay";
+
+ i2c0: i2c@600 {
+ dmas = <0>, <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flx0_default>;
+ i2c-analog-filter;
+ i2c-digital-filter;
+ i2c-digital-filter-width-ns = <35>;
+ status = "okay";
+
+ eeprom@53 {
+ compatible = "atmel,24c02";
+ reg = <0x53>;
+ pagesize = <16>;
+ status = "okay";
+ };
+ };
+};
+
+&flx6 {
+ atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+ status = "okay";
+
+ i2c6: i2c@600 {
+ dmas = <0>, <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flx6_default>;
+ i2c-analog-filter;
+ i2c-digital-filter;
+ i2c-digital-filter-width-ns = <35>;
+ status = "disabled";
+ };
+};
+
+&flx7 {
+ atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+ status = "okay";
+
+ uart7: serial@200 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flx7_default>;
+ status = "okay";
+ };
+};
+
+&macb0 {
+ phy-mode = "rmii";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_macb0_rmii>;
+ status = "okay";
+
+ ethernet-phy@0 {
+ reg = <0x0>;
+ };
+};
+
+&pinctrl {
+ adc {
+ pinctrl_adc_default: adc_default {
+ atmel,pins = <AT91_PIOB 14 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_adtrg_default: adtrg_default {
+ atmel,pins = <AT91_PIOB 18 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>;
+ };
+ };
+
+ can0 {
+ pinctrl_can0_rx_tx: can0_rx_tx {
+ atmel,pins =
+ <AT91_PIOA 9 AT91_PERIPH_B AT91_PINCTRL_NONE /* CANRX0 */
+ AT91_PIOA 10 AT91_PERIPH_B AT91_PINCTRL_NONE /* CANTX0 */
+ AT91_PIOC 9 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_DOWN>; /* Enable CAN Transceivers */
+ };
+ };
+
+ can1 {
+ pinctrl_can1_rx_tx: can1_rx_tx {
+ atmel,pins =
+ <AT91_PIOA 6 AT91_PERIPH_B AT91_PINCTRL_NONE /* CANRX1 */
+ AT91_PIOA 5 AT91_PERIPH_B AT91_PINCTRL_NONE /* CANTX1 */
+ AT91_PIOB 17 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_DOWN>; /* Enable CAN Transceivers */
+ };
+ };
+
+ dbgu {
+ pinctrl_dbgu: dbgu-0 {
+ atmel,pins = <AT91_PIOA 9 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
+ AT91_PIOA 10 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+ };
+
+ ebi {
+ pinctrl_ebi_data_0_7: ebi-data-lsb-0 {
+ atmel,pins =
+ <AT91_PIOD 6 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+ AT91_PIOD 7 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+ AT91_PIOD 8 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+ AT91_PIOD 9 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+ AT91_PIOD 10 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+ AT91_PIOD 11 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+ AT91_PIOD 12 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+ AT91_PIOD 13 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)>;
+ };
+
+ pinctrl_ebi_data_0_15: ebi-data-msb-0 {
+ atmel,pins =
+ <AT91_PIOD 6 AT91_PERIPH_A AT91_PINCTRL_NONE
+ AT91_PIOD 7 AT91_PERIPH_A AT91_PINCTRL_NONE
+ AT91_PIOD 8 AT91_PERIPH_A AT91_PINCTRL_NONE
+ AT91_PIOD 9 AT91_PERIPH_A AT91_PINCTRL_NONE
+ AT91_PIOD 10 AT91_PERIPH_A AT91_PINCTRL_NONE
+ AT91_PIOD 11 AT91_PERIPH_A AT91_PINCTRL_NONE
+ AT91_PIOD 12 AT91_PERIPH_A AT91_PINCTRL_NONE
+ AT91_PIOD 13 AT91_PERIPH_A AT91_PINCTRL_NONE
+ AT91_PIOD 14 AT91_PERIPH_A AT91_PINCTRL_NONE
+ AT91_PIOD 15 AT91_PERIPH_A AT91_PINCTRL_NONE
+ AT91_PIOD 16 AT91_PERIPH_A AT91_PINCTRL_NONE
+ AT91_PIOD 17 AT91_PERIPH_A AT91_PINCTRL_NONE
+ AT91_PIOD 18 AT91_PERIPH_A AT91_PINCTRL_NONE
+ AT91_PIOD 19 AT91_PERIPH_A AT91_PINCTRL_NONE
+ AT91_PIOD 20 AT91_PERIPH_A AT91_PINCTRL_NONE
+ AT91_PIOD 21 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_ebi_addr_nand: ebi-addr-0 {
+ atmel,pins =
+ <AT91_PIOD 2 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+ AT91_PIOD 3 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)>;
+ };
+ };
+
+ flexcom {
+ pinctrl_flx0_default: flx0_twi {
+ atmel,pins =
+ <AT91_PIOA 0 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
+ AT91_PIOA 1 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
+ };
+
+ pinctrl_flx6_default: flx6_twi {
+ atmel,pins =
+ <AT91_PIOA 30 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
+ AT91_PIOA 31 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
+ };
+
+ pinctrl_flx7_default: flx7_usart {
+ atmel,pins =
+ <AT91_PIOC 0 AT91_PERIPH_C AT91_PINCTRL_NONE
+ AT91_PIOC 1 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+ };
+ };
+
+ gpio_keys {
+ pinctrl_key_gpio_default: pinctrl_key_gpio {
+ atmel,pins = <AT91_PIOA 29 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+ };
+
+ leds {
+ pinctrl_gpio_leds: gpio_leds {
+ atmel,pins = <AT91_PIOD 17 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+ AT91_PIOD 19 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+ AT91_PIOD 21 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+ };
+
+ macb0 {
+ pinctrl_macb0_rmii: macb0_rmii-0 {
+ atmel,pins =
+ <AT91_PIOB 0 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB0 periph A */
+ AT91_PIOB 1 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB1 periph A */
+ AT91_PIOB 2 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB2 periph A */
+ AT91_PIOB 3 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB3 periph A */
+ AT91_PIOB 4 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB4 periph A */
+ AT91_PIOB 5 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB5 periph A */
+ AT91_PIOB 6 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB6 periph A */
+ AT91_PIOB 7 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB7 periph A */
+ AT91_PIOB 9 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB9 periph A */
+ AT91_PIOB 10 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PB10 periph A */
+ };
+ };
+
+ nand {
+ pinctrl_nand_oe_we: nand-oe-we-0 {
+ atmel,pins =
+ <AT91_PIOD 0 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+ AT91_PIOD 1 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)>;
+ };
+
+ pinctrl_nand_rb: nand-rb-0 {
+ atmel,pins =
+ <AT91_PIOD 5 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
+ };
+
+ pinctrl_nand_cs: nand-cs-0 {
+ atmel,pins =
+ <AT91_PIOD 4 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
+ };
+ };
+
+ pwm0 {
+ pinctrl_pwm0_0: pwm0_0 {
+ atmel,pins = <AT91_PIOB 12 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_pwm0_1: pwm0_1 {
+ atmel,pins = <AT91_PIOB 13 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_pwm0_2: pwm0_2 {
+ atmel,pins = <AT91_PIOD 16 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+ };
+
+ sdmmc0 {
+ pinctrl_sdmmc0_default: sdmmc0 {
+ atmel,pins =
+ <AT91_PIOA 17 AT91_PERIPH_A (AT91_PINCTRL_DRIVE_STRENGTH_HI) /* PA17 CK periph A with pullup */
+ AT91_PIOA 16 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI) /* PA16 CMD periph A with pullup */
+ AT91_PIOA 15 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI) /* PA15 DAT0 periph A */
+ AT91_PIOA 18 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI) /* PA18 DAT1 periph A with pullup */
+ AT91_PIOA 19 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI) /* PA19 DAT2 periph A with pullup */
+ AT91_PIOA 20 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI)>; /* PA20 DAT3 periph A with pullup */
+ };
+ pinctrl_sdmmc0_cd: sdmmc0_cd {
+ atmel,pins =
+ <AT91_PIOA 25 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+ };
+
+ sdmmc1 {
+ pinctrl_sdmmc1_default: sdmmc1 {
+ atmel,pins =
+ <AT91_PIOA 13 AT91_PERIPH_B (AT91_PINCTRL_DRIVE_STRENGTH_HI) /* PA13 CK periph B */
+ AT91_PIOA 12 AT91_PERIPH_B (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI) /* PA12 CMD periph B with pullup */
+ AT91_PIOA 11 AT91_PERIPH_B (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI) /* PA11 DAT0 periph B with pullup */
+ AT91_PIOA 2 AT91_PERIPH_B (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI) /* PA2 DAT1 periph B with pullup */
+ AT91_PIOA 3 AT91_PERIPH_B (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI) /* PA3 DAT2 periph B with pullup */
+ AT91_PIOA 4 AT91_PERIPH_B (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI)>; /* PA4 DAT3 periph B with pullup */
+ };
+ };
+
+ usb0 {
+ pinctrl_usba_vbus: usba_vbus {
+ atmel,pins = <AT91_PIOA 27 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+ };
+
+ usb1 {
+ pinctrl_usb_default: usb_default {
+ atmel,pins = <AT91_PIOD 18 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+ AT91_PIOD 15 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+ };
+}; /* pinctrl */
+
+&pwm0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm0_0 &pinctrl_pwm0_1 &pinctrl_pwm0_2>;
+ status = "okay";
+};
+
+&sdmmc0 {
+ bus-width = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdmmc0_default &pinctrl_sdmmc0_cd>;
+ cd-gpios = <&pioA 25 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ status = "okay";
+};
+
+&sdmmc1 {
+ bus-width = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdmmc1_default>;
+ status = "disabled";
+};
+
+&shutdown_controller {
+ debounce-delay-us = <976>;
+ status = "okay";
+
+ input@0 {
+ reg = <0>;
+ };
+};
+
+&tcb0 {
+ timer0: timer@0 {
+ compatible = "atmel,tcb-timer";
+ reg = <0>;
+ };
+
+ timer1: timer@1 {
+ compatible = "atmel,tcb-timer";
+ reg = <1>;
+ };
+};
+
+&usb0 {
+ atmel,vbus-gpio = <&pioA 27 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usba_vbus>;
+ status = "okay";
+};
+
+&usb1 {
+ num-ports = <3>;
+ atmel,vbus-gpio = <0
+ &pioD 18 GPIO_ACTIVE_HIGH
+ &pioD 15 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_default>;
+ status = "okay";
+};
+
+&usb2 {
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
+};
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 12+ messages in thread
* Re: [linux][PATCH 6/6] ARM: dts: at91: sam9x60_curiosity: Add device tree for sam9x60_curiosity board
2022-09-07 9:20 ` [linux][PATCH 6/6] ARM: dts: at91: sam9x60_curiosity: Add device tree for sam9x60_curiosity board Hari Prasath
@ 2022-09-08 7:58 ` Claudiu.Beznea
2022-09-08 11:04 ` Krzysztof Kozlowski
1 sibling, 0 replies; 12+ messages in thread
From: Claudiu.Beznea @ 2022-09-08 7:58 UTC (permalink / raw)
To: Hari.PrasathGE, Nicolas.Ferre, davem, krzysztof.kozlowski+dt,
alexandre.belloni, arnd, olof, soc, Manikandan.M, michael,
Horatiu.Vultur, Kavyasree.Kotagiri, devicetree, linux-arm-kernel,
linux-kernel, Durai.ManickamKR
On 07.09.2022 12:20, Hari Prasath wrote:
> From: Manikandan M <manikandan.m@microchip.com>
>
> Add device tree file for sam9x60_curiosity board.
>
> Signed-off-by: Durai Manickam KR <durai.manickamkr@microchip.com>
> Signed-off-by: Manikandan M <manikandan.m@microchip.com>
Manikandan's sob tag should come first as he is the initial author.
> Signed-off-by: Hari Prasath <Hari.PrasathGE@microchip.com>
> ---
> .../devicetree/bindings/arm/atmel-at91.yaml | 6 +
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/at91-sam9x60_curiosity.dts | 532 ++++++++++++++++++
> 3 files changed, 539 insertions(+)
> create mode 100644 arch/arm/boot/dts/at91-sam9x60_curiosity.dts
>
> diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.yaml b/Documentation/devicetree/bindings/arm/atmel-at91.yaml
> index 2b7848bb7769..fae3a3090fbd 100644
> --- a/Documentation/devicetree/bindings/arm/atmel-at91.yaml
> +++ b/Documentation/devicetree/bindings/arm/atmel-at91.yaml
> @@ -97,6 +97,12 @@ properties:
> - const: microchip,sam9x60
> - const: atmel,at91sam9
>
> + - description: SAM9X60 Curiosity board
> + items:
> + - const: microchip,sam9x60-curiosity
> + - const: microchip,sam9x60
> + - const: atmel,at91sam9
> +
> - description: Nattis v2 board with Natte v2 power board
> items:
> - const: axentia,nattis-2
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 595e870750cd..cd60cda5d187 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -51,6 +51,7 @@ dtb-$(CONFIG_SOC_AT91SAM9) += \
> at91sam9x25ek.dtb \
> at91sam9x35ek.dtb
> dtb-$(CONFIG_SOC_SAM9X60) += \
> + at91-sam9x60_curiosity.dtb \
> at91-sam9x60ek.dtb
> dtb-$(CONFIG_SOC_SAM_V7) += \
> at91-kizbox2-2.dtb \
> diff --git a/arch/arm/boot/dts/at91-sam9x60_curiosity.dts b/arch/arm/boot/dts/at91-sam9x60_curiosity.dts
> new file mode 100644
> index 000000000000..75e6727b5e3a
> --- /dev/null
> +++ b/arch/arm/boot/dts/at91-sam9x60_curiosity.dts
> @@ -0,0 +1,532 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * at91-sam9x60_curiosity.dts - Device Tree file for Microchip SAM9X60 CURIOSITY board
> + *
> + * Copyright (C) 2022 Microchip Technology Inc. and its subsidiaries
> + *
> + * Author: Manikandan M <manikandan.m@microchip.com>
> + */
> +/dts-v1/;
> +#include "sam9x60.dtsi"
> +#include <dt-bindings/input/input.h>
> +
> +/ {
> + model = "Microchip SAM9X60 CURIOSITY";
> + compatible = "microchip,sam9x60-curiosity", "microchip,sam9x60", "atmel,at91sam9";
> +
> + aliases {
> + i2c0 = &i2c0;
> + i2c1 = &i2c6;
> + serial2 = &uart7;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + memory@20000000 {
> + reg = <0x20000000 0x8000000>;
> + };
> +
> + clocks {
> + slow_xtal {
> + clock-frequency = <32768>;
> + };
> +
> + main_xtal {
> + clock-frequency = <24000000>;
> + };
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_key_gpio_default>;
> + status = "okay";
No need for status here, okay is the default one.
> +
> + button-user {
> + label = "PB_USER";
> + gpios = <&pioA 29 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_PROG1>;
> + wakeup-source;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpio_leds>;
> + status = "okay";
Ditto
> +
> + red {
> + label = "red";
> + gpios = <&pioD 17 GPIO_ACTIVE_HIGH>;
> + };
> +
> + green {
> + label = "green";
> + gpios = <&pioD 19 GPIO_ACTIVE_HIGH>;
> + };
> +
> + blue {
> + label = "blue";
> + gpios = <&pioD 21 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +
> + regulators: regulators {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <0>;
You can remove the regulators container and simple-bus as this thows
compilation warnings.
> +
> + vdd_1v8: fixed-regulator-vdd_1v8@0 {
And you can use generic names for regulators: e.g. regulator-0.
> + compatible = "regulator-fixed";
> + regulator-name = "VDD_1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + status = "okay";
> + };
> +
> + vdd_1v15: fixed-regulator-vdd_1v15@1 {
> + compatible = "regulator-fixed";
> + regulator-name = "VDD_1V15";
> + regulator-min-microvolt = <1150000>;
> + regulator-max-microvolt = <1150000>;
> + regulator-always-on;
> + status = "okay";
> + };
> +
> + vdd1_3v3: fixed-regulator-vdd1_3v3@2 {
> + compatible = "regulator-fixed";
> + regulator-name = "VDD1_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + status = "okay";
> + };
> + };
Please keep the entries in ths container alphabetically sorted.
> +};
> +
> +&adc {
> + vddana-supply = <&vdd1_3v3>;
> + vref-supply = <&vdd1_3v3>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_adc_default &pinctrl_adtrg_default>;
> + status = "okay";
> +};
> +
> +&can0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_can0_rx_tx>;
> + status = "disabled"; /* Conflict with dbgu. */
> +};
> +
> +&can1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_can1_rx_tx>;
> + status = "okay";
> +};
> +
> +&dbgu {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_dbgu>;
> + status = "okay"; /* Conflict with can0. */
> +};
> +
> +&ebi {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ebi_addr_nand &pinctrl_ebi_data_0_7>;
> + status = "okay";
> +
> + nand_controller: nand-controller {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_nand_oe_we &pinctrl_nand_cs &pinctrl_nand_rb>;
> + status = "okay";
> +
> + nand@3 {
> + reg = <0x3 0x0 0x800000>;
> + rb-gpios = <&pioD 5 GPIO_ACTIVE_HIGH>;
> + cs-gpios = <&pioD 4 GPIO_ACTIVE_HIGH>;
> + nand-bus-width = <8>;
> + nand-ecc-mode = "hw";
> + nand-ecc-strength = <8>;
> + nand-ecc-step-size = <512>;
> + nand-on-flash-bbt;
> + label = "atmel_nand";
> +
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + at91bootstrap@0 {
> + label = "at91bootstrap";
> + reg = <0x0 0x40000>;
> + };
> +
> + uboot@40000 {
> + label = "u-boot";
> + reg = <0x40000 0xc0000>;
> + };
> +
> + ubootenvred@100000 {
> + label = "U-Boot Env Redundant";
> + reg = <0x100000 0x40000>;
> + };
> +
> + ubootenv@140000 {
> + label = "U-Boot Env";
> + reg = <0x140000 0x40000>;
> + };
> +
> + dtb@180000 {
> + label = "device tree";
> + reg = <0x180000 0x80000>;
> + };
> +
> + kernel@200000 {
> + label = "kernel";
> + reg = <0x200000 0x600000>;
> + };
> +
> + rootfs@800000 {
> + label = "rootfs";
> + reg = <0x800000 0x1f800000>;
> + };
> + };
> + };
> + };
> +};
> +
> +&flx0 {
> + atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
> + status = "okay";
> +
> + i2c0: i2c@600 {
> + dmas = <0>, <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flx0_default>;
> + i2c-analog-filter;
> + i2c-digital-filter;
> + i2c-digital-filter-width-ns = <35>;
> + status = "okay";
> +
> + eeprom@53 {
> + compatible = "atmel,24c02";
> + reg = <0x53>;
> + pagesize = <16>;
> + status = "okay";
> + };
> + };
> +};
> +
> +&flx6 {
> + atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
> + status = "okay";
> +
> + i2c6: i2c@600 {
> + dmas = <0>, <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flx6_default>;
> + i2c-analog-filter;
> + i2c-digital-filter;
> + i2c-digital-filter-width-ns = <35>;
> + status = "disabled";
> + };
> +};
> +
> +&flx7 {
> + atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
> + status = "okay";
> +
> + uart7: serial@200 {
> + #address-cells = <1>;
> + #size-cells = <0>;
These could be removed.
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flx7_default>;
> + status = "okay";
> + };
> +};
> +
> +&macb0 {
> + phy-mode = "rmii";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_macb0_rmii>;
> + status = "okay";
> +
> + ethernet-phy@0 {
> + reg = <0x0>;
> + };
> +};
> +
> +&pinctrl {
> + adc {
> + pinctrl_adc_default: adc_default {
No underscores in the names. Same for the rest of pinctrl definitions.
> + atmel,pins = <AT91_PIOB 14 AT91_PERIPH_A AT91_PINCTRL_NONE>;
> + };
> +
> + pinctrl_adtrg_default: adtrg_default {
> + atmel,pins = <AT91_PIOB 18 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>;
> + };
> + };
> +
> + can0 {
> + pinctrl_can0_rx_tx: can0_rx_tx {
> + atmel,pins =
> + <AT91_PIOA 9 AT91_PERIPH_B AT91_PINCTRL_NONE /* CANRX0 */
> + AT91_PIOA 10 AT91_PERIPH_B AT91_PINCTRL_NONE /* CANTX0 */
> + AT91_PIOC 9 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_DOWN>; /* Enable CAN Transceivers */
> + };
> + };
> +
> + can1 {
> + pinctrl_can1_rx_tx: can1_rx_tx {
> + atmel,pins =
> + <AT91_PIOA 6 AT91_PERIPH_B AT91_PINCTRL_NONE /* CANRX1 */
> + AT91_PIOA 5 AT91_PERIPH_B AT91_PINCTRL_NONE /* CANTX1 */
> + AT91_PIOB 17 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_DOWN>; /* Enable CAN Transceivers */
> + };
> + };
> +
> + dbgu {
> + pinctrl_dbgu: dbgu-0 {
> + atmel,pins = <AT91_PIOA 9 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
> + AT91_PIOA 10 AT91_PERIPH_A AT91_PINCTRL_NONE>;
> + };
> + };
> +
> + ebi {
> + pinctrl_ebi_data_0_7: ebi-data-lsb-0 {
> + atmel,pins =
> + <AT91_PIOD 6 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
> + AT91_PIOD 7 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
> + AT91_PIOD 8 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
> + AT91_PIOD 9 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
> + AT91_PIOD 10 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
> + AT91_PIOD 11 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
> + AT91_PIOD 12 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
> + AT91_PIOD 13 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)>;
> + };
> +
> + pinctrl_ebi_data_0_15: ebi-data-msb-0 {
> + atmel,pins =
> + <AT91_PIOD 6 AT91_PERIPH_A AT91_PINCTRL_NONE
> + AT91_PIOD 7 AT91_PERIPH_A AT91_PINCTRL_NONE
> + AT91_PIOD 8 AT91_PERIPH_A AT91_PINCTRL_NONE
> + AT91_PIOD 9 AT91_PERIPH_A AT91_PINCTRL_NONE
> + AT91_PIOD 10 AT91_PERIPH_A AT91_PINCTRL_NONE
> + AT91_PIOD 11 AT91_PERIPH_A AT91_PINCTRL_NONE
> + AT91_PIOD 12 AT91_PERIPH_A AT91_PINCTRL_NONE
> + AT91_PIOD 13 AT91_PERIPH_A AT91_PINCTRL_NONE
> + AT91_PIOD 14 AT91_PERIPH_A AT91_PINCTRL_NONE
> + AT91_PIOD 15 AT91_PERIPH_A AT91_PINCTRL_NONE
> + AT91_PIOD 16 AT91_PERIPH_A AT91_PINCTRL_NONE
> + AT91_PIOD 17 AT91_PERIPH_A AT91_PINCTRL_NONE
> + AT91_PIOD 18 AT91_PERIPH_A AT91_PINCTRL_NONE
> + AT91_PIOD 19 AT91_PERIPH_A AT91_PINCTRL_NONE
> + AT91_PIOD 20 AT91_PERIPH_A AT91_PINCTRL_NONE
> + AT91_PIOD 21 AT91_PERIPH_A AT91_PINCTRL_NONE>;
> + };
> +
> + pinctrl_ebi_addr_nand: ebi-addr-0 {
> + atmel,pins =
> + <AT91_PIOD 2 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
> + AT91_PIOD 3 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)>;
> + };
> + };
> +
> + flexcom {
> + pinctrl_flx0_default: flx0_twi {
> + atmel,pins =
> + <AT91_PIOA 0 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
> + AT91_PIOA 1 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
> + };
> +
> + pinctrl_flx6_default: flx6_twi {
> + atmel,pins =
> + <AT91_PIOA 30 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
> + AT91_PIOA 31 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
> + };
> +
> + pinctrl_flx7_default: flx7_usart {
> + atmel,pins =
> + <AT91_PIOC 0 AT91_PERIPH_C AT91_PINCTRL_NONE
> + AT91_PIOC 1 AT91_PERIPH_C AT91_PINCTRL_NONE>;
> + };
> + };
> +
> + gpio_keys {
> + pinctrl_key_gpio_default: pinctrl_key_gpio {
> + atmel,pins = <AT91_PIOA 29 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
> + };
> + };
> +
> + leds {
> + pinctrl_gpio_leds: gpio_leds {
> + atmel,pins = <AT91_PIOD 17 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
> + AT91_PIOD 19 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
> + AT91_PIOD 21 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
> + };
> + };
> +
> + macb0 {
> + pinctrl_macb0_rmii: macb0_rmii-0 {
> + atmel,pins =
> + <AT91_PIOB 0 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB0 periph A */
> + AT91_PIOB 1 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB1 periph A */
> + AT91_PIOB 2 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB2 periph A */
> + AT91_PIOB 3 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB3 periph A */
> + AT91_PIOB 4 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB4 periph A */
> + AT91_PIOB 5 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB5 periph A */
> + AT91_PIOB 6 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB6 periph A */
> + AT91_PIOB 7 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB7 periph A */
> + AT91_PIOB 9 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB9 periph A */
> + AT91_PIOB 10 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PB10 periph A */
> + };
> + };
> +
> + nand {
> + pinctrl_nand_oe_we: nand-oe-we-0 {
> + atmel,pins =
> + <AT91_PIOD 0 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
> + AT91_PIOD 1 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)>;
> + };
> +
> + pinctrl_nand_rb: nand-rb-0 {
> + atmel,pins =
> + <AT91_PIOD 5 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
> + };
> +
> + pinctrl_nand_cs: nand-cs-0 {
> + atmel,pins =
> + <AT91_PIOD 4 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
> + };
> + };
> +
> + pwm0 {
> + pinctrl_pwm0_0: pwm0_0 {
> + atmel,pins = <AT91_PIOB 12 AT91_PERIPH_B AT91_PINCTRL_NONE>;
> + };
> +
> + pinctrl_pwm0_1: pwm0_1 {
> + atmel,pins = <AT91_PIOB 13 AT91_PERIPH_B AT91_PINCTRL_NONE>;
> + };
> +
> + pinctrl_pwm0_2: pwm0_2 {
> + atmel,pins = <AT91_PIOD 16 AT91_PERIPH_B AT91_PINCTRL_NONE>;
> + };
> + };
> +
> + sdmmc0 {
> + pinctrl_sdmmc0_default: sdmmc0 {
> + atmel,pins =
> + <AT91_PIOA 17 AT91_PERIPH_A (AT91_PINCTRL_DRIVE_STRENGTH_HI) /* PA17 CK periph A with pullup */
> + AT91_PIOA 16 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI) /* PA16 CMD periph A with pullup */
> + AT91_PIOA 15 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI) /* PA15 DAT0 periph A */
> + AT91_PIOA 18 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI) /* PA18 DAT1 periph A with pullup */
> + AT91_PIOA 19 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI) /* PA19 DAT2 periph A with pullup */
> + AT91_PIOA 20 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI)>; /* PA20 DAT3 periph A with pullup */
> + };
> + pinctrl_sdmmc0_cd: sdmmc0_cd {
> + atmel,pins =
> + <AT91_PIOA 25 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
> + };
> + };
> +
> + sdmmc1 {
> + pinctrl_sdmmc1_default: sdmmc1 {
> + atmel,pins =
> + <AT91_PIOA 13 AT91_PERIPH_B (AT91_PINCTRL_DRIVE_STRENGTH_HI) /* PA13 CK periph B */
> + AT91_PIOA 12 AT91_PERIPH_B (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI) /* PA12 CMD periph B with pullup */
> + AT91_PIOA 11 AT91_PERIPH_B (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI) /* PA11 DAT0 periph B with pullup */
> + AT91_PIOA 2 AT91_PERIPH_B (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI) /* PA2 DAT1 periph B with pullup */
> + AT91_PIOA 3 AT91_PERIPH_B (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI) /* PA3 DAT2 periph B with pullup */
> + AT91_PIOA 4 AT91_PERIPH_B (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI)>; /* PA4 DAT3 periph B with pullup */
> + };
> + };
> +
> + usb0 {
> + pinctrl_usba_vbus: usba_vbus {
> + atmel,pins = <AT91_PIOA 27 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
> + };
> + };
> +
> + usb1 {
> + pinctrl_usb_default: usb_default {
> + atmel,pins = <AT91_PIOD 18 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
> + AT91_PIOD 15 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
> + };
> + };
> +}; /* pinctrl */
> +
> +&pwm0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm0_0 &pinctrl_pwm0_1 &pinctrl_pwm0_2>;
> + status = "okay";
> +};
> +
> +&sdmmc0 {
> + bus-width = <4>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_sdmmc0_default &pinctrl_sdmmc0_cd>;
> + cd-gpios = <&pioA 25 GPIO_ACTIVE_LOW>;
> + disable-wp;
> + status = "okay";
> +};
> +
> +&sdmmc1 {
> + bus-width = <4>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_sdmmc1_default>;
> + status = "disabled";
> +};
Is this needed here as it is disabled? Is it available on the board or it
conflicts with some other peripherals?
> +
> +&shutdown_controller {
> + debounce-delay-us = <976>;
> + status = "okay";
> +
> + input@0 {
> + reg = <0>;
> + };
> +};
> +
> +&tcb0 {
> + timer0: timer@0 {
> + compatible = "atmel,tcb-timer";
> + reg = <0>;
> + };
> +
> + timer1: timer@1 {
> + compatible = "atmel,tcb-timer";
> + reg = <1>;
> + };
> +};
> +
> +&usb0 {
> + atmel,vbus-gpio = <&pioA 27 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usba_vbus>;
> + status = "okay";
> +};
> +
> +&usb1 {
> + num-ports = <3>;
> + atmel,vbus-gpio = <0
> + &pioD 18 GPIO_ACTIVE_HIGH
> + &pioD 15 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usb_default>;
> + status = "okay";
> +};
> +
> +&usb2 {
> + status = "okay";
> +};
> +
> +&watchdog {
> + status = "okay";
> +};
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [linux][PATCH 5/6] ARM: dts: at91: sam9x60: Add missing flexcom definitions
2022-09-07 9:20 ` [linux][PATCH 5/6] ARM: dts: at91: sam9x60: Add missing flexcom definitions Hari Prasath
@ 2022-09-08 7:58 ` Claudiu.Beznea
0 siblings, 0 replies; 12+ messages in thread
From: Claudiu.Beznea @ 2022-09-08 7:58 UTC (permalink / raw)
To: Hari.PrasathGE, Nicolas.Ferre, davem, krzysztof.kozlowski+dt,
alexandre.belloni, arnd, olof, soc, Manikandan.M, michael,
Horatiu.Vultur, Kavyasree.Kotagiri, devicetree, linux-arm-kernel,
linux-kernel, Durai.ManickamKR
On 07.09.2022 12:20, Hari Prasath wrote:
> From: Durai Manickam KR <durai.manickamkr@microchip.com>
>
> Added the missing flexcom functions for all the flexcom nodes.
Did you got the chance to test all these?
>
> Signed-off-by: Manikandan M <manikandan.m@microchip.com>
> Signed-off-by: Durai Manickam KR <durai.manickamkr@microchip.com>
> Signed-off-by: Hari Prasath <Hari.PrasathGE@microchip.com>
> ---
> arch/arm/boot/dts/sam9x60.dtsi | 547 +++++++++++++++++++++++++++++++++
> 1 file changed, 547 insertions(+)
>
> diff --git a/arch/arm/boot/dts/sam9x60.dtsi b/arch/arm/boot/dts/sam9x60.dtsi
> index feeabc53e0ec..1c580c3ba7c3 100644
> --- a/arch/arm/boot/dts/sam9x60.dtsi
> +++ b/arch/arm/boot/dts/sam9x60.dtsi
> @@ -170,6 +170,27 @@
> ranges = <0x0 0xf0000000 0x800>;
> status = "disabled";
>
> + uart4: serial@200 {
> + compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> + reg = <0x200 0x200>;
> + interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(8))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(9))>;
> + dma-names = "tx", "rx";
> + clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
> + clock-names = "usart";
> + atmel,use-dma-rx;
> + atmel,use-dma-tx;
> + atmel,fifo-size = <16>;
> + status = "disabled";
> + };
> +
> spi4: spi@400 {
> compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
> reg = <0x400 0x200>;
> @@ -188,6 +209,24 @@
> atmel,fifo-size = <16>;
> status = "disabled";
> };
> +
> + i2c4: i2c@600 {
> + compatible = "microchip,sam9x60-i2c";
> + reg = <0x600 0x200>;
> + interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
> + clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(8))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(9))>;
> + dma-names = "tx", "rx";
> + atmel,fifo-size = <16>;
> + status = "disabled";
> + };
> };
>
> flx5: flexcom@f0004000 {
> @@ -219,6 +258,43 @@
> atmel,fifo-size = <16>;
> status = "disabled";
> };
> +
> + spi5: spi@400 {
> + compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
> + reg = <0x400 0x200>;
> + interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
> + clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
> + clock-names = "spi_clk";
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(10))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(11))>;
> + dma-names = "tx", "rx";
> + atmel,fifo-size = <16>;
> + status = "disabled";
> + };
> +
> + i2c5: i2c@600 {
> + compatible = "microchip,sam9x60-i2c";
> + reg = <0x600 0x200>;
> + interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
> + clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(10))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(11))>;
> + dma-names = "tx", "rx";
> + atmel,fifo-size = <16>;
> + status = "disabled";
> + };
> };
>
> dma0: dma-controller@f0008000 {
> @@ -290,6 +366,45 @@
> #size-cells = <1>;
> ranges = <0x0 0xf0020000 0x800>;
> status = "disabled";
> +
> + uart11: serial@200 {
> + compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> + reg = <0x200 0x200>;
> + interrupts = <32 IRQ_TYPE_LEVEL_HIGH 7>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(22))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(23))>;
> + dma-names = "tx", "rx";
> + clocks = <&pmc PMC_TYPE_PERIPHERAL 32>;
> + clock-names = "usart";
> + atmel,use-dma-rx;
> + atmel,use-dma-tx;
> + atmel,fifo-size = <16>;
> + status = "disabled";
> + };
> +
> + i2c11: i2c@600 {
> + compatible = "microchip,sam9x60-i2c";
> + reg = <0x600 0x200>;
> + interrupts = <32 IRQ_TYPE_LEVEL_HIGH 7>;
> + clocks = <&pmc PMC_TYPE_PERIPHERAL 32>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(22))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(23))>;
> + dma-names = "tx", "rx";
> + atmel,fifo-size = <16>;
> + status = "disabled";
> + };
> };
>
> flx12: flexcom@f0024000 {
> @@ -300,6 +415,45 @@
> #size-cells = <1>;
> ranges = <0x0 0xf0024000 0x800>;
> status = "disabled";
> +
> + uart12: serial@200 {
> + compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> + reg = <0x200 0x200>;
> + interrupts = <33 IRQ_TYPE_LEVEL_HIGH 7>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(24))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(25))>;
> + dma-names = "tx", "rx";
> + clocks = <&pmc PMC_TYPE_PERIPHERAL 33>;
> + clock-names = "usart";
> + atmel,use-dma-rx;
> + atmel,use-dma-tx;
> + atmel,fifo-size = <16>;
> + status = "disabled";
> + };
> +
> + i2c12: i2c@600 {
> + compatible = "microchip,sam9x60-i2c";
> + reg = <0x600 0x200>;
> + interrupts = <33 IRQ_TYPE_LEVEL_HIGH 7>;
> + clocks = <&pmc PMC_TYPE_PERIPHERAL 33>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(24))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(25))>;
> + dma-names = "tx", "rx";
> + atmel,fifo-size = <16>;
> + status = "disabled";
> + };
> };
>
> pit64b: timer@f0028000 {
> @@ -419,6 +573,27 @@
> ranges = <0x0 0xf8010000 0x800>;
> status = "disabled";
>
> + uart6: serial@200 {
> + compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> + reg = <0x200 0x200>;
> + interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(12))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(13))>;
> + dma-names = "tx", "rx";
> + clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
> + clock-names = "usart";
> + atmel,use-dma-rx;
> + atmel,use-dma-tx;
> + atmel,fifo-size = <16>;
> + status = "disabled";
> + };
> +
> i2c6: i2c@600 {
> compatible = "microchip,sam9x60-i2c";
> reg = <0x600 0x200>;
> @@ -446,6 +621,45 @@
> #size-cells = <1>;
> ranges = <0x0 0xf8014000 0x800>;
> status = "disabled";
> +
> + uart7: serial@200 {
> + compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> + reg = <0x200 0x200>;
> + interrupts = <10 IRQ_TYPE_LEVEL_HIGH 7>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(14))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(15))>;
> + dma-names = "tx", "rx";
> + clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
> + clock-names = "usart";
> + atmel,use-dma-rx;
> + atmel,use-dma-tx;
> + atmel,fifo-size = <16>;
> + status = "disabled";
> + };
> +
> + i2c7: i2c@600 {
> + compatible = "microchip,sam9x60-i2c";
> + reg = <0x600 0x200>;
> + interrupts = <10 IRQ_TYPE_LEVEL_HIGH 7>;
> + clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(14))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(15))>;
> + dma-names = "tx", "rx";
> + atmel,fifo-size = <16>;
> + status = "disabled";
> + };
> };
>
> flx8: flexcom@f8018000 {
> @@ -456,15 +670,96 @@
> #size-cells = <1>;
> ranges = <0x0 0xf8018000 0x800>;
> status = "disabled";
> +
> + uart8: serial@200 {
> + compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> + reg = <0x200 0x200>;
> + interrupts = <11 IRQ_TYPE_LEVEL_HIGH 7>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(16))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(17))>;
> + dma-names = "tx", "rx";
> + clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
> + clock-names = "usart";
> + atmel,use-dma-rx;
> + atmel,use-dma-tx;
> + atmel,fifo-size = <16>;
> + status = "disabled";
> + };
> +
> + i2c8: i2c@600 {
> + compatible = "microchip,sam9x60-i2c";
> + reg = <0x600 0x200>;
> + interrupts = <11 IRQ_TYPE_LEVEL_HIGH 7>;
> + clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(16))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(17))>;
> + dma-names = "tx", "rx";
> + atmel,fifo-size = <16>;
> + status = "disabled";
> + };
> };
>
> flx0: flexcom@f801c000 {
> compatible = "atmel,sama5d2-flexcom";
> reg = <0xf801c000 0x200>;
> clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> ranges = <0x0 0xf801c000 0x800>;
> status = "disabled";
>
> + uart0: serial@200 {
> + compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> + reg = <0x200 0x200>;
> + interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(0))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(1))>;
> + dma-names = "tx", "rx";
> + clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
> + clock-names = "usart";
> + atmel,use-dma-rx;
> + atmel,use-dma-tx;
> + atmel,fifo-size = <16>;
> + status = "disabled";
> + };
> +
> + spi0: spi@400 {
> + compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
> + reg = <0x400 0x200>;
> + interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
> + clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
> + clock-names = "spi_clk";
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(0))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(1))>;
> + dma-names = "tx", "rx";
> + atmel,fifo-size = <16>;
> + status = "disabled";
> + };
> +
> i2c0: i2c@600 {
> compatible = "microchip,sam9x60-i2c";
> reg = <0x600 0x200>;
> @@ -494,6 +789,64 @@
> #size-cells = <1>;
> ranges = <0x0 0xf8020000 0x800>;
> status = "disabled";
> +
> + uart1: serial@200 {
> + compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> + reg = <0x200 0x200>;
> + interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(2))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(3))>;
> + dma-names = "tx", "rx";
> + clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
> + clock-names = "usart";
> + atmel,use-dma-rx;
> + atmel,use-dma-tx;
> + atmel,fifo-size = <16>;
> + status = "disabled";
> + };
> +
> + spi1: spi@400 {
> + compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
> + reg = <0x400 0x200>;
> + interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
> + clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
> + clock-names = "spi_clk";
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(2))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(3))>;
> + dma-names = "tx", "rx";
> + atmel,fifo-size = <16>;
> + status = "disabled";
> + };
> +
> + i2c1: i2c@600 {
> + compatible = "microchip,sam9x60-i2c";
> + reg = <0x600 0x200>;
> + interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
> + clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(2))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(3))>;
> + dma-names = "tx", "rx";
> + atmel,fifo-size = <16>;
> + status = "disabled";
> + };
> };
>
> flx2: flexcom@f8024000 {
> @@ -504,6 +857,64 @@
> #size-cells = <1>;
> ranges = <0x0 0xf8024000 0x800>;
> status = "disabled";
> +
> + uart2: serial@200 {
> + compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> + reg = <0x200 0x200>;
> + interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(4))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(5))>;
> + dma-names = "tx", "rx";
> + clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
> + clock-names = "usart";
> + atmel,use-dma-rx;
> + atmel,use-dma-tx;
> + atmel,fifo-size = <16>;
> + status = "disabled";
> + };
> +
> + spi2: spi@400 {
> + compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
> + reg = <0x400 0x200>;
> + interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
> + clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
> + clock-names = "spi_clk";
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(4))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(5))>;
> + dma-names = "tx", "rx";
> + atmel,fifo-size = <16>;
> + status = "disabled";
> + };
> +
> + i2c2: i2c@600 {
> + compatible = "microchip,sam9x60-i2c";
> + reg = <0x600 0x200>;
> + interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
> + clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(4))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(5))>;
> + dma-names = "tx", "rx";
> + atmel,fifo-size = <16>;
> + status = "disabled";
> + };
> };
>
> flx3: flexcom@f8028000 {
> @@ -514,6 +925,64 @@
> #size-cells = <1>;
> ranges = <0x0 0xf8028000 0x800>;
> status = "disabled";
> +
> + uart3: serial@200 {
> + compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> + reg = <0x200 0x200>;
> + interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(6))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(7))>;
> + dma-names = "tx", "rx";
> + clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
> + clock-names = "usart";
> + atmel,use-dma-rx;
> + atmel,use-dma-tx;
> + atmel,fifo-size = <16>;
> + status = "disabled";
> + };
> +
> + spi3: spi@400 {
> + compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
> + reg = <0x400 0x200>;
> + interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
> + clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
> + clock-names = "spi_clk";
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(6))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(7))>;
> + dma-names = "tx", "rx";
> + atmel,fifo-size = <16>;
> + status = "disabled";
> + };
> +
> + i2c3: i2c@600 {
> + compatible = "microchip,sam9x60-i2c";
> + reg = <0x600 0x200>;
> + interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
> + clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(6))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(7))>;
> + dma-names = "tx", "rx";
> + atmel,fifo-size = <16>;
> + status = "disabled";
> + };
> };
>
> macb0: ethernet@f802c000 {
> @@ -579,6 +1048,45 @@
> #size-cells = <1>;
> ranges = <0x0 0xf8040000 0x800>;
> status = "disabled";
> +
> + uart9: serial@200 {
> + compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> + reg = <0x200 0x200>;
> + interrupts = <15 IRQ_TYPE_LEVEL_HIGH 7>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(18))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(19))>;
> + dma-names = "tx", "rx";
> + clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
> + clock-names = "usart";
> + atmel,use-dma-rx;
> + atmel,use-dma-tx;
> + atmel,fifo-size = <16>;
> + status = "disabled";
> + };
> +
> + i2c9: i2c@600 {
> + compatible = "microchip,sam9x60-i2c";
> + reg = <0x600 0x200>;
> + interrupts = <15 IRQ_TYPE_LEVEL_HIGH 7>;
> + clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(18))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(19))>;
> + dma-names = "tx", "rx";
> + atmel,fifo-size = <16>;
> + status = "disabled";
> + };
> };
>
> flx10: flexcom@f8044000 {
> @@ -589,6 +1097,45 @@
> #size-cells = <1>;
> ranges = <0x0 0xf8044000 0x800>;
> status = "disabled";
> +
> + uart10: serial@200 {
> + compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> + reg = <0x200 0x200>;
> + interrupts = <16 IRQ_TYPE_LEVEL_HIGH 7>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(20))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(21))>;
> + dma-names = "tx", "rx";
> + clocks = <&pmc PMC_TYPE_PERIPHERAL 16>;
> + clock-names = "usart";
> + atmel,use-dma-rx;
> + atmel,use-dma-tx;
> + atmel,fifo-size = <16>;
> + status = "disabled";
> + };
> +
> + i2c10: i2c@600 {
> + compatible = "microchip,sam9x60-i2c";
> + reg = <0x600 0x200>;
> + interrupts = <16 IRQ_TYPE_LEVEL_HIGH 7>;
> + clocks = <&pmc PMC_TYPE_PERIPHERAL 16>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(20))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(21))>;
> + dma-names = "tx", "rx";
> + atmel,fifo-size = <16>;
> + status = "disabled";
> + };
> };
>
> isi: isi@f8048000 {
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [linux][PATCH 4/6] ARM: dts: at91: sam9x60: Add DMA bindigs for the flexcom nodes
2022-09-07 9:20 ` [linux][PATCH 4/6] ARM: dts: at91: sam9x60: Add DMA bindigs for the flexcom nodes Hari Prasath
@ 2022-09-08 7:58 ` Claudiu.Beznea
0 siblings, 0 replies; 12+ messages in thread
From: Claudiu.Beznea @ 2022-09-08 7:58 UTC (permalink / raw)
To: Hari.PrasathGE, Nicolas.Ferre, davem, krzysztof.kozlowski+dt,
alexandre.belloni, arnd, olof, soc, Manikandan.M, michael,
Horatiu.Vultur, Kavyasree.Kotagiri, devicetree, linux-arm-kernel,
linux-kernel, Durai.ManickamKR
On 07.09.2022 12:20, Hari Prasath wrote:
> Add dma bindings for flexcom nodes in the soc dtsi file. Users those who
> don't wish to use the DMA function for their flexcom functions can
> overwrite the dma bindings in the board device tree file.
>
> Signed-off-by: Manikandan M <manikandan.m@microchip.com>
> Signed-off-by: Hari Prasath <Hari.PrasathGE@microchip.com>
As you are the author, your sob tag should be first.
> ---
> arch/arm/boot/dts/at91-sam9x60ek.dts | 3 +++
> arch/arm/boot/dts/sam9x60.dtsi | 27 +++++++++++++++++++++++++++
> 2 files changed, 30 insertions(+)
>
> diff --git a/arch/arm/boot/dts/at91-sam9x60ek.dts b/arch/arm/boot/dts/at91-sam9x60ek.dts
> index 9d9e50c77794..9ad528e1bdd2 100644
> --- a/arch/arm/boot/dts/at91-sam9x60ek.dts
> +++ b/arch/arm/boot/dts/at91-sam9x60ek.dts
> @@ -213,6 +213,7 @@
> i2c0: i2c@600 {
> #address-cells = <1>;
> #size-cells = <0>;
> + dmas = <0>, <0>;
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_flx0_default>;
> i2c-analog-filter;
> @@ -234,6 +235,7 @@
> status = "disabled";
>
> spi4: spi@400 {
> + dmas = <0>, <0>;
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_flx4_default>;
> status = "disabled";
> @@ -258,6 +260,7 @@
> i2c6: i2c@600 {
> #address-cells = <1>;
> #size-cells = <0>;
> + dmas = <0>, <0>;
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_flx6_default>;
> i2c-analog-filter;
> diff --git a/arch/arm/boot/dts/sam9x60.dtsi b/arch/arm/boot/dts/sam9x60.dtsi
> index 224b406c8384..feeabc53e0ec 100644
> --- a/arch/arm/boot/dts/sam9x60.dtsi
> +++ b/arch/arm/boot/dts/sam9x60.dtsi
> @@ -176,6 +176,15 @@
> interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
> clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
> clock-names = "spi_clk";
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(8))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(9))>;
> + dma-names = "tx", "rx";
> atmel,fifo-size = <16>;
> status = "disabled";
> };
> @@ -415,6 +424,15 @@
> reg = <0x600 0x200>;
> interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
> clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(12))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(13))>;
> + dma-names = "tx", "rx";
> atmel,fifo-size = <16>;
> status = "disabled";
> };
> @@ -454,6 +472,15 @@
> #address-cells = <1>;
> #size-cells = <0>;
> clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(0))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(1))>;
> + dma-names = "tx", "rx";
> atmel,fifo-size = <16>;
> status = "disabled";
> };
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [linux][PATCH 2/6] ARM: dts: at91: sam9x60: Move flexcom definitions to the SoC dtsi
2022-09-07 9:20 ` [linux][PATCH 2/6] ARM: dts: at91: sam9x60: Move flexcom definitions to the SoC dtsi Hari Prasath
@ 2022-09-08 7:59 ` Claudiu.Beznea
0 siblings, 0 replies; 12+ messages in thread
From: Claudiu.Beznea @ 2022-09-08 7:59 UTC (permalink / raw)
To: Hari.PrasathGE, Nicolas.Ferre, davem, krzysztof.kozlowski+dt,
alexandre.belloni, arnd, olof, soc, Manikandan.M, michael,
Horatiu.Vultur, Kavyasree.Kotagiri, devicetree, linux-arm-kernel,
linux-kernel, Durai.ManickamKR
On 07.09.2022 12:20, Hari Prasath wrote:
> Move the flexcom definitions to the SoC specifc DTSI file retaining only
> the pinmux and desired functions in the board specific DTS file of
> sam9x60ek.
>
> Signed-off-by: Hari Prasath <Hari.PrasathGE@microchip.com>
> Signed-off-by: Manikandan M <manikandan.m@microchip.com>
> Signed-off-by: Durai Manickam KR <durai.manickamkr@microchip.com>
> ---
> arch/arm/boot/dts/at91-sam9x60ek.dts | 34 +-----------------
> arch/arm/boot/dts/sam9x60.dtsi | 52 ++++++++++++++++++++++++++--
> 2 files changed, 51 insertions(+), 35 deletions(-)
>
> diff --git a/arch/arm/boot/dts/at91-sam9x60ek.dts b/arch/arm/boot/dts/at91-sam9x60ek.dts
> index b9b7a235ef89..9d9e50c77794 100644
> --- a/arch/arm/boot/dts/at91-sam9x60ek.dts
> +++ b/arch/arm/boot/dts/at91-sam9x60ek.dts
> @@ -211,15 +211,10 @@
> status = "okay";
>
> i2c0: i2c@600 {
> - compatible = "microchip,sam9x60-i2c";
> - reg = <0x600 0x200>;
> - interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
> #address-cells = <1>;
> #size-cells = <0>;
> - clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_flx0_default>;
> - atmel,fifo-size = <16>;
> i2c-analog-filter;
> i2c-digital-filter;
> i2c-digital-filter-width-ns = <35>;
> @@ -239,16 +234,8 @@
> status = "disabled";
>
> spi4: spi@400 {
> - compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
> - reg = <0x400 0x200>;
> - interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
> - clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
> - clock-names = "spi_clk";
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_flx4_default>;
> - atmel,fifo-size = <16>;
> - #address-cells = <1>;
> - #size-cells = <0>;
This is not moved it is deleted, it should go in a different patch.
> status = "disabled";
> };
> };
> @@ -258,22 +245,8 @@
> status = "okay";
>
> uart5: serial@200 {
> - compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> - reg = <0x200 0x200>;
> - interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
> - dmas = <&dma0
> - (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> - AT91_XDMAC_DT_PERID(10))>,
> - <&dma0
> - (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> - AT91_XDMAC_DT_PERID(11))>;
> - dma-names = "tx", "rx";
> - clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
> - clock-names = "usart";
> - pinctrl-0 = <&pinctrl_flx5_default>;
> pinctrl-names = "default";
> - atmel,use-dma-rx;
> - atmel,use-dma-tx;
> + pinctrl-0 = <&pinctrl_flx5_default>;
> status = "okay";
> };
> };
> @@ -283,15 +256,10 @@
> status = "okay";
>
> i2c6: i2c@600 {
> - compatible = "microchip,sam9x60-i2c";
> - reg = <0x600 0x200>;
> - interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
> #address-cells = <1>;
> #size-cells = <0>;
> - clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_flx6_default>;
> - atmel,fifo-size = <16>;
> i2c-analog-filter;
> i2c-digital-filter;
> i2c-digital-filter-width-ns = <35>;
> diff --git a/arch/arm/boot/dts/sam9x60.dtsi b/arch/arm/boot/dts/sam9x60.dtsi
> index d3f60f6a456d..f0e0dc20de1b 100644
> --- a/arch/arm/boot/dts/sam9x60.dtsi
> +++ b/arch/arm/boot/dts/sam9x60.dtsi
> @@ -169,6 +169,16 @@
> #size-cells = <1>;
> ranges = <0x0 0xf0000000 0x800>;
> status = "disabled";
> +
> + spi4: spi@400 {
> + compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
> + reg = <0x400 0x200>;
> + interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
> + clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
> + clock-names = "spi_clk";
> + atmel,fifo-size = <16>;
> + status = "disabled";
> + };
> };
>
> flx5: flexcom@f0004000 {
> @@ -179,6 +189,26 @@
> #size-cells = <1>;
> ranges = <0x0 0xf0004000 0x800>;
> status = "disabled";
> +
> + uart5: serial@200 {
> + compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
> + reg = <0x200 0x200>;
> + interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(10))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) |
> + AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(11))>;
> + dma-names = "tx", "rx";
> + clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
> + clock-names = "usart";
> + atmel,use-dma-rx;
> + atmel,use-dma-tx;
> + status = "disabled";
> + };
> };
>
> dma0: dma-controller@f0008000 {
> @@ -378,6 +408,15 @@
> #size-cells = <1>;
> ranges = <0x0 0xf8010000 0x800>;
> status = "disabled";
> +
> + i2c6: i2c@600 {
> + compatible = "microchip,sam9x60-i2c";
> + reg = <0x600 0x200>;
> + interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
> + clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
> + atmel,fifo-size = <16>;
> + status = "disabled";
> + };
> };
>
> flx7: flexcom@f8014000 {
> @@ -404,10 +443,19 @@
> compatible = "atmel,sama5d2-flexcom";
> reg = <0xf801c000 0x200>;
> clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
> - #address-cells = <1>;
> - #size-cells = <1>;
This should remain here.
> ranges = <0x0 0xf801c000 0x800>;
> status = "disabled";
> +
> + i2c0: i2c@600 {
> + compatible = "microchip,sam9x60-i2c";
> + reg = <0x600 0x200>;
> + interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
> + atmel,fifo-size = <16>;
> + status = "disabled";
> + };
> };
>
> flx1: flexcom@f8020000 {
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [linux][PATCH 6/6] ARM: dts: at91: sam9x60_curiosity: Add device tree for sam9x60_curiosity board
2022-09-07 9:20 ` [linux][PATCH 6/6] ARM: dts: at91: sam9x60_curiosity: Add device tree for sam9x60_curiosity board Hari Prasath
2022-09-08 7:58 ` Claudiu.Beznea
@ 2022-09-08 11:04 ` Krzysztof Kozlowski
1 sibling, 0 replies; 12+ messages in thread
From: Krzysztof Kozlowski @ 2022-09-08 11:04 UTC (permalink / raw)
To: Hari Prasath, nicolas.ferre, claudiu.beznea, davem,
krzysztof.kozlowski+dt, alexandre.belloni, arnd, olof, soc,
manikandan.m, michael, horatiu.vultur, kavyasree.kotagiri,
devicetree, linux-arm-kernel, linux-kernel, durai.manickamkr
On 07/09/2022 11:20, Hari Prasath wrote:
> From: Manikandan M <manikandan.m@microchip.com>
>
> Add device tree file for sam9x60_curiosity board.
>
> Signed-off-by: Durai Manickam KR <durai.manickamkr@microchip.com>
> Signed-off-by: Manikandan M <manikandan.m@microchip.com>
> Signed-off-by: Hari Prasath <Hari.PrasathGE@microchip.com>
> ---
> .../devicetree/bindings/arm/atmel-at91.yaml | 6 +
Bindings are separate patches.
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/at91-sam9x60_curiosity.dts | 532 ++++++++++++++++++
> 3 files changed, 539 insertions(+)
> create mode 100644 arch/arm/boot/dts/at91-sam9x60_curiosity.dts
>
> diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.yaml b/Documentation/devicetree/bindings/arm/atmel-at91.yaml
> index 2b7848bb7769..fae3a3090fbd 100644
> --- a/Documentation/devicetree/bindings/arm/atmel-at91.yaml
> +++ b/Documentation/devicetree/bindings/arm/atmel-at91.yaml
> @@ -97,6 +97,12 @@ properties:
> - const: microchip,sam9x60
> - const: atmel,at91sam9
>
> + - description: SAM9X60 Curiosity board
> + items:
> + - const: microchip,sam9x60-curiosity
> + - const: microchip,sam9x60
> + - const: atmel,at91sam9
This should be rather together with previous entry as an enum.
> +
> - description: Nattis v2 board with Natte v2 power board
> items:
> - const: axentia,nattis-2
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 595e870750cd..cd60cda5d187 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -51,6 +51,7 @@ dtb-$(CONFIG_SOC_AT91SAM9) += \
> at91sam9x25ek.dtb \
> at91sam9x35ek.dtb
> dtb-$(CONFIG_SOC_SAM9X60) += \
> + at91-sam9x60_curiosity.dtb \
> at91-sam9x60ek.dtb
> dtb-$(CONFIG_SOC_SAM_V7) += \
> at91-kizbox2-2.dtb \
> diff --git a/arch/arm/boot/dts/at91-sam9x60_curiosity.dts b/arch/arm/boot/dts/at91-sam9x60_curiosity.dts
> new file mode 100644
> index 000000000000..75e6727b5e3a
> --- /dev/null
> +++ b/arch/arm/boot/dts/at91-sam9x60_curiosity.dts
> @@ -0,0 +1,532 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * at91-sam9x60_curiosity.dts - Device Tree file for Microchip SAM9X60 CURIOSITY board
> + *
> + * Copyright (C) 2022 Microchip Technology Inc. and its subsidiaries
> + *
> + * Author: Manikandan M <manikandan.m@microchip.com>
> + */
> +/dts-v1/;
> +#include "sam9x60.dtsi"
> +#include <dt-bindings/input/input.h>
> +
> +/ {
> + model = "Microchip SAM9X60 CURIOSITY";
> + compatible = "microchip,sam9x60-curiosity", "microchip,sam9x60", "atmel,at91sam9";
> +
> + aliases {
> + i2c0 = &i2c0;
> + i2c1 = &i2c6;
> + serial2 = &uart7;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + memory@20000000 {
> + reg = <0x20000000 0x8000000>;
> + };
> +
> + clocks {
> + slow_xtal {
No underscores in node names... If you override nodes, do it via label.
> + clock-frequency = <32768>;
> + };
> +
> + main_xtal {
> + clock-frequency = <24000000>;
> + };
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_key_gpio_default>;
> + status = "okay";
Okay is by default.
> +
> + button-user {
> + label = "PB_USER";
> + gpios = <&pioA 29 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_PROG1>;
> + wakeup-source;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpio_leds>;
> + status = "okay";
Ditto
> +
> + red {
Does not look like you tested the DTS against bindings. Please run `make
dtbs_check` (see Documentation/devicetree/bindings/writing-schema.rst
for instructions).
You need to fix all warnings in your DTS.
> + label = "red";
> + gpios = <&pioD 17 GPIO_ACTIVE_HIGH>;
> + };
> +
> + green {
> + label = "green";
> + gpios = <&pioD 19 GPIO_ACTIVE_HIGH>;
> + };
> +
> + blue {
> + label = "blue";
> + gpios = <&pioD 21 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +
> + regulators: regulators {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + vdd_1v8: fixed-regulator-vdd_1v8@0 {
No underscores in node names. No prefix "fixed-". This is just a regulator.
> + compatible = "regulator-fixed";
> + regulator-name = "VDD_1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + status = "okay";
Really?
> + };
> +
> + vdd_1v15: fixed-regulator-vdd_1v15@1 {
> + compatible = "regulator-fixed";
> + regulator-name = "VDD_1V15";
> + regulator-min-microvolt = <1150000>;
> + regulator-max-microvolt = <1150000>;
> + regulator-always-on;
> + status = "okay";
> + };
> +
> + vdd1_3v3: fixed-regulator-vdd1_3v3@2 {
> + compatible = "regulator-fixed";
> + regulator-name = "VDD1_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + status = "okay";
> + };
> + };
> +};
> +
> +&adc {
> + vddana-supply = <&vdd1_3v3>;
> + vref-supply = <&vdd1_3v3>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_adc_default &pinctrl_adtrg_default>;
> + status = "okay";
> +};
> +
> +&can0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_can0_rx_tx>;
> + status = "disabled"; /* Conflict with dbgu. */
> +};
> +
> +&can1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_can1_rx_tx>;
> + status = "okay";
> +};
> +
> +&dbgu {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_dbgu>;
> + status = "okay"; /* Conflict with can0. */
> +};
> +
> +&ebi {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ebi_addr_nand &pinctrl_ebi_data_0_7>;
> + status = "okay";
> +
> + nand_controller: nand-controller {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_nand_oe_we &pinctrl_nand_cs &pinctrl_nand_rb>;
> + status = "okay";
> +
> + nand@3 {
> + reg = <0x3 0x0 0x800000>;
> + rb-gpios = <&pioD 5 GPIO_ACTIVE_HIGH>;
> + cs-gpios = <&pioD 4 GPIO_ACTIVE_HIGH>;
> + nand-bus-width = <8>;
> + nand-ecc-mode = "hw";
> + nand-ecc-strength = <8>;
> + nand-ecc-step-size = <512>;
> + nand-on-flash-bbt;
> + label = "atmel_nand";
> +
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + at91bootstrap@0 {
> + label = "at91bootstrap";
> + reg = <0x0 0x40000>;
> + };
> +
> + uboot@40000 {
> + label = "u-boot";
> + reg = <0x40000 0xc0000>;
> + };
> +
> + ubootenvred@100000 {
> + label = "U-Boot Env Redundant";
> + reg = <0x100000 0x40000>;
> + };
> +
> + ubootenv@140000 {
> + label = "U-Boot Env";
> + reg = <0x140000 0x40000>;
> + };
> +
> + dtb@180000 {
> + label = "device tree";
> + reg = <0x180000 0x80000>;
> + };
> +
> + kernel@200000 {
> + label = "kernel";
> + reg = <0x200000 0x600000>;
> + };
> +
> + rootfs@800000 {
> + label = "rootfs";
> + reg = <0x800000 0x1f800000>;
> + };
> + };
> + };
> + };
> +};
> +
> +&flx0 {
> + atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
> + status = "okay";
> +
> + i2c0: i2c@600 {
> + dmas = <0>, <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flx0_default>;
> + i2c-analog-filter;
> + i2c-digital-filter;
> + i2c-digital-filter-width-ns = <35>;
> + status = "okay";
??
> +
> + eeprom@53 {
> + compatible = "atmel,24c02";
> + reg = <0x53>;
> + pagesize = <16>;
> + status = "okay";
> + };
> + };
> +};
> +
> +&flx6 {
> + atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
> + status = "okay";
> +
> + i2c6: i2c@600 {
> + dmas = <0>, <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flx6_default>;
> + i2c-analog-filter;
> + i2c-digital-filter;
> + i2c-digital-filter-width-ns = <35>;
> + status = "disabled";
> + };
> +};
> +
> +&flx7 {
> + atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
> + status = "okay";
> +
> + uart7: serial@200 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flx7_default>;
> + status = "okay";
> + };
> +};
> +
> +&macb0 {
> + phy-mode = "rmii";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_macb0_rmii>;
> + status = "okay";
> +
> + ethernet-phy@0 {
> + reg = <0x0>;
> + };
> +};
> +
> +&pinctrl {
> + adc {
> + pinctrl_adc_default: adc_default {
No underscores in node names.
Best regards,
Krzysztof
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2022-09-08 11:06 UTC | newest]
Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-09-07 9:20 [linux][PATCH 0/6] Add support for sam9x60 curiosity board Hari Prasath
2022-09-07 9:20 ` [linux][PATCH 1/6] ARM: dts: at91: sam9x60: Fix the label numbering for the flexcom functions Hari Prasath
2022-09-07 9:20 ` [linux][PATCH 2/6] ARM: dts: at91: sam9x60: Move flexcom definitions to the SoC dtsi Hari Prasath
2022-09-08 7:59 ` Claudiu.Beznea
2022-09-07 9:20 ` [linux][PATCH 3/6] ARM: dts: at91: sam9x60: Specify the FIFO size for the Flexcom UART Hari Prasath
2022-09-07 9:20 ` [linux][PATCH 4/6] ARM: dts: at91: sam9x60: Add DMA bindigs for the flexcom nodes Hari Prasath
2022-09-08 7:58 ` Claudiu.Beznea
2022-09-07 9:20 ` [linux][PATCH 5/6] ARM: dts: at91: sam9x60: Add missing flexcom definitions Hari Prasath
2022-09-08 7:58 ` Claudiu.Beznea
2022-09-07 9:20 ` [linux][PATCH 6/6] ARM: dts: at91: sam9x60_curiosity: Add device tree for sam9x60_curiosity board Hari Prasath
2022-09-08 7:58 ` Claudiu.Beznea
2022-09-08 11:04 ` Krzysztof Kozlowski
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).