* [PATCH V5 0/3] AM68 SK: Add initial support
@ 2023-01-16 7:14 Sinthu Raja
2023-01-16 7:14 ` [PATCH V5 1/3] dt-bindings: arm: ti: Add binding for AM68 SK Sinthu Raja
` (4 more replies)
0 siblings, 5 replies; 8+ messages in thread
From: Sinthu Raja @ 2023-01-16 7:14 UTC (permalink / raw)
To: Nishanth Menon, Tero Kristo, Rob Herring
Cc: Vignesh Raghavendra, Krzysztof Kozlowski, linux-arm-kernel,
devicetree, linux-kernel, Sinthu Raja
From: Sinthu Raja <sinthu.raja@ti.com>
Hi All,
This series of patches add support for AM68 Starter kit(SK). AM68 SK
is a low cost, small form factor board designed for TI’s AM68 SoC.
Refer below link to AM68 Technical Reference Manual for further details:
http://www.ti.com/lit/pdf/spruj28
Design files can be referrred from https://www.ti.com/lit/zip/SPRR463
Changes in V5:
=============
Address review comments:
- Remove the unessential comment.
- Remove alignment property from secure-ddr node, as no memory is allocated out
of this region.
Changes in V4:
=============
Repost after rebasing to 6.2 rc1
Changes in V3:
==============
Address all the review comments and the changes are captured in separate patches.
- Remove the unused nodes that are disabled by default.
- Update the gpio regulator node: gpio-regulator-tlv to "regulator-tlv".
V1: https://lore.kernel.org/linux-arm-kernel/20221018123849.23695-1-sinthu.raja@ti.com/t/#mbe43b02221733bb6eb06b203359e90ec08406afc
V2: https://lore.kernel.org/lkml/20221107123852.8063-1-sinthu.raja@ti.com/
V3: https://lore.kernel.org/lkml/20230110110052.14851-1-sinthu.raja@ti.com/
V4: https://lore.kernel.org/lkml/20230105151740.29436-1-sinthu.raja@ti.com/
Sinthu Raja (3):
dt-bindings: arm: ti: Add binding for AM68 SK
arm64: dts: ti: Add initial support for AM68 SK System on Module
arm64: dts: ti: k3-am68-sk: Add support for AM68 SK base board
.../devicetree/bindings/arm/ti/k3.yaml | 1 +
arch/arm64/boot/dts/ti/Makefile | 2 +
.../boot/dts/ti/k3-am68-sk-base-board.dts | 335 ++++++++++++++++++
arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi | 29 ++
4 files changed, 367 insertions(+)
create mode 100644 arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
create mode 100644 arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi
--
2.36.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 8+ messages in thread* [PATCH V5 1/3] dt-bindings: arm: ti: Add binding for AM68 SK 2023-01-16 7:14 [PATCH V5 0/3] AM68 SK: Add initial support Sinthu Raja @ 2023-01-16 7:14 ` Sinthu Raja 2023-01-16 7:14 ` [PATCH V5 2/3] arm64: dts: ti: Add initial support for AM68 SK System on Module Sinthu Raja ` (3 subsequent siblings) 4 siblings, 0 replies; 8+ messages in thread From: Sinthu Raja @ 2023-01-16 7:14 UTC (permalink / raw) To: Nishanth Menon, Tero Kristo, Rob Herring Cc: Vignesh Raghavendra, Krzysztof Kozlowski, linux-arm-kernel, devicetree, linux-kernel, Sinthu Raja, Krzysztof Kozlowski From: Sinthu Raja <sinthu.raja@ti.com> AM68 Starter Kit is a low cost, small form factor board designed for TI's AM68 SoC which is optimized to provide best in class performance for industrial applications and add binding for the same. Signed-off-by: Sinthu Raja <sinthu.raja@ti.com> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> --- No changes in V4 & V5 Changes in V3: ============= Add Acked-by tag. Changes in V2: ============= *Address review comment - add entry in alphabetical order. Documentation/devicetree/bindings/arm/ti/k3.yaml | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/arm/ti/k3.yaml b/Documentation/devicetree/bindings/arm/ti/k3.yaml index 203faab80142..acbc25108533 100644 --- a/Documentation/devicetree/bindings/arm/ti/k3.yaml +++ b/Documentation/devicetree/bindings/arm/ti/k3.yaml @@ -69,6 +69,7 @@ properties: - description: K3 J721s2 SoC items: - enum: + - ti,am68-sk - ti,j721s2-evm - const: ti,j721s2 -- 2.36.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH V5 2/3] arm64: dts: ti: Add initial support for AM68 SK System on Module 2023-01-16 7:14 [PATCH V5 0/3] AM68 SK: Add initial support Sinthu Raja 2023-01-16 7:14 ` [PATCH V5 1/3] dt-bindings: arm: ti: Add binding for AM68 SK Sinthu Raja @ 2023-01-16 7:14 ` Sinthu Raja 2023-01-16 14:02 ` Vaishnav Achath 2023-01-16 7:14 ` [PATCH V5 3/3] arm64: dts: ti: k3-am68-sk: Add support for AM68 SK base board Sinthu Raja ` (2 subsequent siblings) 4 siblings, 1 reply; 8+ messages in thread From: Sinthu Raja @ 2023-01-16 7:14 UTC (permalink / raw) To: Nishanth Menon, Tero Kristo, Rob Herring Cc: Vignesh Raghavendra, Krzysztof Kozlowski, linux-arm-kernel, devicetree, linux-kernel, Sinthu Raja From: Sinthu Raja <sinthu.raja@ti.com> AM68 Starter Kit (SK) is a low cost, small form factor board designed for TI’s AM68 SoC. TI’s AM68 SoC comprises of dual core A72, high performance vision accelerators, hardware accelerators, latest C71x DSP, high bandwidth real-time IPs for capture and display. The SoC is power optimized to provide best in class performance for industrial applications. AM68 SK supports the following interfaces: * 16 GB LPDDR4 RAM * x1 Gigabit Ethernet interface * x1 USB 3.1 Type-C port * x2 USB 3.1 Type-A ports * x1 PCIe M.2 M Key * 512 Mbit OSPI flash * x2 CSI2 Camera interface (RPi and TI Camera connector) * 40-pin Raspberry Pi GPIO header SK's System on Module (SoM) contains the SoC and DDR. Therefore, add DT node for the SOC and DDR on the SoM. Schematics: https://www.ti.com/lit/zip/SPRR463 TRM: http://www.ti.com/lit/pdf/spruj28 Signed-off-by: Sinthu Raja <sinthu.raja@ti.com> --- Changes in V5: ============= Address review comments: - Remove the unessential comment. - Remove alignment property from secure-ddr node, as no memory is allocated out of this region. No changes in V4. Changes in V3: ============= Addressed review comments - Removed the unused nodes that are disabled by default. OSPI support will be added once the OSPI node is enabled for J721s2/AM68 in main DTSI. Changes in V2: ============= Address review comments - drop the empty lines. V1: https://lore.kernel.org/linux-arm-kernel/20221018123849.23695-3-sinthu.raja@ti.com/ V2: https://lore.kernel.org/lkml/20221107123852.8063-3-sinthu.raja@ti.com/ V3: https://lore.kernel.org/lkml/20230110110052.14851-3-sinthu.raja@ti.com/ V4: https://lore.kernel.org/lkml/20230105151740.29436-3-sinthu.raja@ti.com/ arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi | 29 ++++++++++++++++++++++ 1 file changed, 29 insertions(+) create mode 100644 arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi diff --git a/arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi b/arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi new file mode 100644 index 000000000000..e92431250729 --- /dev/null +++ b/arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi @@ -0,0 +1,29 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2023 Texas Instruments Incorporated - https://www.ti.com/ + */ + +/dts-v1/; + +#include "k3-j721s2.dtsi" +#include <dt-bindings/gpio/gpio.h> + +/ { + memory@80000000 { + device_type = "memory"; + /* 16 GB RAM */ + reg = <0x00 0x80000000 0x00 0x80000000>, + <0x08 0x80000000 0x03 0x80000000>; + }; + + reserved_memory: reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + secure_ddr: optee@9e800000 { + reg = <0x00 0x9e800000 0x00 0x01800000>; + no-map; + }; + }; +}; -- 2.36.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 8+ messages in thread
* Re: [PATCH V5 2/3] arm64: dts: ti: Add initial support for AM68 SK System on Module 2023-01-16 7:14 ` [PATCH V5 2/3] arm64: dts: ti: Add initial support for AM68 SK System on Module Sinthu Raja @ 2023-01-16 14:02 ` Vaishnav Achath 0 siblings, 0 replies; 8+ messages in thread From: Vaishnav Achath @ 2023-01-16 14:02 UTC (permalink / raw) To: Sinthu Raja, Nishanth Menon, Tero Kristo, Rob Herring Cc: Vignesh Raghavendra, Krzysztof Kozlowski, linux-arm-kernel, devicetree, linux-kernel, Sinthu Raja Hi Sinthu, On 16/01/23 12:44, Sinthu Raja wrote: > From: Sinthu Raja <sinthu.raja@ti.com> > > AM68 Starter Kit (SK) is a low cost, small form factor board designed > for TI’s AM68 SoC. TI’s AM68 SoC comprises of dual core A72, high > performance vision accelerators, hardware accelerators, latest C71x > DSP, high bandwidth real-time IPs for capture and display. The SoC is > power optimized to provide best in class performance for industrial > applications. > > AM68 SK supports the following interfaces: > * 16 GB LPDDR4 RAM > * x1 Gigabit Ethernet interface > * x1 USB 3.1 Type-C port > * x2 USB 3.1 Type-A ports > * x1 PCIe M.2 M Key > * 512 Mbit OSPI flash > * x2 CSI2 Camera interface (RPi and TI Camera connector) > * 40-pin Raspberry Pi GPIO header > > SK's System on Module (SoM) contains the SoC and DDR. > Therefore, add DT node for the SOC and DDR on the SoM. > > Schematics: https://www.ti.com/lit/zip/SPRR463 > TRM: http://www.ti.com/lit/pdf/spruj28 > > Signed-off-by: Sinthu Raja <sinthu.raja@ti.com> > --- > > Changes in V5: > ============= > Address review comments: > - Remove the unessential comment. > - Remove alignment property from secure-ddr node, as no memory is allocated out > of this region. > > No changes in V4. > > Changes in V3: > ============= > Addressed review comments > - Removed the unused nodes that are disabled by default. > OSPI support will be added once the OSPI node is enabled for J721s2/AM68 in main DTSI. > > Changes in V2: > ============= > Address review comments > - drop the empty lines. > > V1: https://lore.kernel.org/linux-arm-kernel/20221018123849.23695-3-sinthu.raja@ti.com/ > V2: https://lore.kernel.org/lkml/20221107123852.8063-3-sinthu.raja@ti.com/ > V3: https://lore.kernel.org/lkml/20230110110052.14851-3-sinthu.raja@ti.com/ > V4: https://lore.kernel.org/lkml/20230105151740.29436-3-sinthu.raja@ti.com/ > > arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi | 29 ++++++++++++++++++++++ > 1 file changed, 29 insertions(+) > create mode 100644 arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi > > diff --git a/arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi b/arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi > new file mode 100644 > index 000000000000..e92431250729 > --- /dev/null > +++ b/arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi > @@ -0,0 +1,29 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Copyright (C) 2023 Texas Instruments Incorporated - https://www.ti.com/ > + */ > + > +/dts-v1/; > + > +#include "k3-j721s2.dtsi" > +#include <dt-bindings/gpio/gpio.h> > + > +/ { > + memory@80000000 { > + device_type = "memory"; > + /* 16 GB RAM */ > + reg = <0x00 0x80000000 0x00 0x80000000>, > + <0x08 0x80000000 0x03 0x80000000>; > + }; > + > + reserved_memory: reserved-memory { > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + > + secure_ddr: optee@9e800000 { > + reg = <0x00 0x9e800000 0x00 0x01800000>; > + no-map; > + }; > + }; Thank you for making the updates, Tested-by: Vaishnav Achath <vaishnav.a@ti.com> Bootlogs during my testing : https://gist.github.com/vaishnavachath/64b58be41028c646b06568a73faed2fd > +}; -- Regards, Vaishnav _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH V5 3/3] arm64: dts: ti: k3-am68-sk: Add support for AM68 SK base board 2023-01-16 7:14 [PATCH V5 0/3] AM68 SK: Add initial support Sinthu Raja 2023-01-16 7:14 ` [PATCH V5 1/3] dt-bindings: arm: ti: Add binding for AM68 SK Sinthu Raja 2023-01-16 7:14 ` [PATCH V5 2/3] arm64: dts: ti: Add initial support for AM68 SK System on Module Sinthu Raja @ 2023-01-16 7:14 ` Sinthu Raja 2023-01-16 14:04 ` Vaishnav Achath 2023-01-16 11:17 ` [PATCH V5 0/3] AM68 SK: Add initial support Neha Malcom Francis 2023-01-23 17:39 ` Vignesh Raghavendra 4 siblings, 1 reply; 8+ messages in thread From: Sinthu Raja @ 2023-01-16 7:14 UTC (permalink / raw) To: Nishanth Menon, Tero Kristo, Rob Herring Cc: Vignesh Raghavendra, Krzysztof Kozlowski, linux-arm-kernel, devicetree, linux-kernel, Sinthu Raja From: Sinthu Raja <sinthu.raja@ti.com> The SK architecture comprises of baseboard and a SOM board. The AM68 Starter Kit's baseboard contains most of the actual connectors, power supply etc. The System on Module (SoM) is plugged on to the base board. Therefore, add support for peripherals brought out in the base board. Schematics: https://www.ti.com/lit/zip/SPRR463 Signed-off-by: Sinthu Raja <sinthu.raja@ti.com> --- No changes in V4 & V5 Changes in V3: ============= *Address review comments: - Remove the unused nodes that are disabled by default. - Update the gpio regulator node: gpio-regulator-tlv to "regulator-tlv". Changes in V2: ============= *Address the review comments: - Update the commit description. - Update the regulator nodes: fixedregulator to "regulator-" - Update the commit $subject to align with rest of the commits. - Drop the blank lines - Change the node names that are added with underscore("_") with "-" V1: https://lore.kernel.org/linux-arm-kernel/20221018123849.23695-4-sinthu.raja@ti.com/ V2: https://lore.kernel.org/lkml/20221107123852.8063-4-sinthu.raja@ti.com/ V3: https://lore.kernel.org/lkml/20230110110052.14851-4-sinthu.raja@ti.com/ V4: https://lore.kernel.org/lkml/20230105151740.29436-4-sinthu.raja@ti.com/ arch/arm64/boot/dts/ti/Makefile | 2 + .../boot/dts/ti/k3-am68-sk-base-board.dts | 335 ++++++++++++++++++ 2 files changed, 337 insertions(+) create mode 100644 arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile index cf7c509538a4..1b4e8b573de5 100644 --- a/arch/arm64/boot/dts/ti/Makefile +++ b/arch/arm64/boot/dts/ti/Makefile @@ -12,6 +12,8 @@ dtb-$(CONFIG_ARCH_K3) += k3-am6528-iot2050-basic-pg2.dtb dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced.dtb dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced-pg2.dtb +dtb-$(CONFIG_ARCH_K3) += k3-am68-sk-base-board.dtb + dtb-$(CONFIG_ARCH_K3) += k3-j721e-beagleboneai64.dtb dtb-$(CONFIG_ARCH_K3) += k3-j721e-common-proc-board.dtb dtb-$(CONFIG_ARCH_K3) += k3-j721e-sk.dtb diff --git a/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts b/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts new file mode 100644 index 000000000000..2091cd2431fb --- /dev/null +++ b/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts @@ -0,0 +1,335 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2023 Texas Instruments Incorporated - https://www.ti.com/ + * + * Base Board: https://www.ti.com/lit/zip/SPRR463 + */ + +/dts-v1/; + +#include "k3-am68-sk-som.dtsi" +#include <dt-bindings/net/ti-dp83867.h> +#include <dt-bindings/phy/phy-cadence.h> +#include <dt-bindings/phy/phy.h> +#include <dt-bindings/mux/ti-serdes.h> + +/ { + compatible = "ti,am68-sk", "ti,j721s2"; + model = "Texas Instruments AM68 SK"; + + chosen { + stdout-path = "serial2:115200n8"; + }; + + aliases { + serial2 = &main_uart8; + mmc1 = &main_sdhci1; + can0 = &mcu_mcan0; + can1 = &mcu_mcan1; + can2 = &main_mcan6; + can3 = &main_mcan7; + }; + + vusb_main: regulator-vusb-main5v0 { + /* USB MAIN INPUT 5V DC */ + compatible = "regulator-fixed"; + regulator-name = "vusb-main5v0"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + }; + + vsys_3v3: regulator-vsys3v3 { + /* Output of LM5141 */ + compatible = "regulator-fixed"; + regulator-name = "vsys_3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vusb_main>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_mmc1: regulator-sd { + /* Output of TPS22918 */ + compatible = "regulator-fixed"; + regulator-name = "vdd_mmc1"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + enable-active-high; + vin-supply = <&vsys_3v3>; + gpio = <&exp1 10 GPIO_ACTIVE_HIGH>; + }; + + vdd_sd_dv: regulator-tlv71033 { + /* Output of TLV71033 */ + compatible = "regulator-gpio"; + regulator-name = "tlv71033"; + pinctrl-names = "default"; + pinctrl-0 = <&vdd_sd_dv_pins_default>; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + vin-supply = <&vsys_3v3>; + gpios = <&main_gpio0 49 GPIO_ACTIVE_HIGH>; + states = <1800000 0x0>, + <3300000 0x1>; + }; + + vsys_io_1v8: regulator-vsys-io-1v8 { + compatible = "regulator-fixed"; + regulator-name = "vsys_io_1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + vsys_io_1v2: regulator-vsys-io-1v2 { + compatible = "regulator-fixed"; + regulator-name = "vsys_io_1v2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + }; + + transceiver1: can-phy0 { + compatible = "ti,tcan1042"; + #phy-cells = <0>; + max-bitrate = <5000000>; + }; + + transceiver2: can-phy1 { + compatible = "ti,tcan1042"; + #phy-cells = <0>; + max-bitrate = <5000000>; + }; + + transceiver3: can-phy2 { + compatible = "ti,tcan1042"; + #phy-cells = <0>; + max-bitrate = <5000000>; + }; + + transceiver4: can-phy3 { + compatible = "ti,tcan1042"; + #phy-cells = <0>; + max-bitrate = <5000000>; + }; +}; + +&main_pmx0 { + main_uart8_pins_default: main-uart8-pins-default { + pinctrl-single,pins = < + J721S2_IOPAD(0x0d0, PIN_INPUT, 11) /* (AF26) SPI0_CS1.UART8_RXD */ + J721S2_IOPAD(0x0d4, PIN_OUTPUT, 11) /* (AH27) SPI0_CLK.UART8_TXD */ + >; + }; + + main_i2c0_pins_default: main-i2c0-pins-default { + pinctrl-single,pins = < + J721S2_IOPAD(0x0e0, PIN_INPUT, 0) /* (AH25) I2C0_SCL */ + J721S2_IOPAD(0x0e4, PIN_INPUT, 0) /* (AE24) I2C0_SDA */ + >; + }; + + main_mmc1_pins_default: main-mmc1-pins-default { + pinctrl-single,pins = < + J721S2_IOPAD(0x104, PIN_INPUT, 0) /* (P23) MMC1_CLK */ + J721S2_IOPAD(0x108, PIN_INPUT, 0) /* (N24) MMC1_CMD */ + J721S2_IOPAD(0x0fc, PIN_INPUT, 0) /* (M23) MMC1_DAT0 */ + J721S2_IOPAD(0x0f8, PIN_INPUT, 0) /* (P24) MMC1_DAT1 */ + J721S2_IOPAD(0x0f4, PIN_INPUT, 0) /* (R24) MMC1_DAT2 */ + J721S2_IOPAD(0x0f0, PIN_INPUT, 0) /* (R22) MMC1_DAT3 */ + J721S2_IOPAD(0x0e8, PIN_INPUT, 8) /* (AE25) TIMER_IO0.MMC1_SDCD */ + >; + }; + + vdd_sd_dv_pins_default: vdd-sd-dv-pins-default { + pinctrl-single,pins = < + J721S2_IOPAD(0x0c4, PIN_INPUT, 7) /* (AB26) ECAP0_IN_APWM_OUT.GPIO0_49 */ + >; + }; + + main_usbss0_pins_default: main-usbss0-pins-default { + pinctrl-single,pins = < + J721S2_IOPAD(0x0ec, PIN_OUTPUT, 6) /* (AG25) TIMER_IO1.USB0_DRVVBUS */ + >; + }; + + main_mcan6_pins_default: main-mcan6-pins-default { + pinctrl-single,pins = < + J721S2_IOPAD(0x098, PIN_INPUT, 0) /* (V25) MCASP0_AXR10.MCAN6_RX */ + J721S2_IOPAD(0x094, PIN_INPUT, 0) /* (AA25) MCASP0_AXR9.MCAN6_TX */ + >; + }; + + main_mcan7_pins_default: main-mcan7-pins-default { + pinctrl-single,pins = < + J721S2_IOPAD(0x0a0, PIN_INPUT, 0) /* (AB25) MCASP0_AXR12.MCAN7_RX */ + J721S2_IOPAD(0x09c, PIN_INPUT, 0) /* (T24) MCASP0_AXR11.MCAN7_TX */ + >; + }; +}; + +&wkup_pmx0 { + mcu_cpsw_pins_default: mcu-cpsw-pins-default { + pinctrl-single,pins = < + J721S2_WKUP_IOPAD(0x094, PIN_INPUT, 0) /* (B22) MCU_RGMII1_RD0 */ + J721S2_WKUP_IOPAD(0x090, PIN_INPUT, 0) /* (B21) MCU_RGMII1_RD1 */ + J721S2_WKUP_IOPAD(0x08c, PIN_INPUT, 0) /* (C22) MCU_RGMII1_RD2 */ + J721S2_WKUP_IOPAD(0x088, PIN_INPUT, 0) /* (D23) MCU_RGMII1_RD3 */ + J721S2_WKUP_IOPAD(0x084, PIN_INPUT, 0) /* (D22) MCU_RGMII1_RXC */ + J721S2_WKUP_IOPAD(0x06c, PIN_INPUT, 0) /* (E23) MCU_RGMII1_RX_CTL */ + J721S2_WKUP_IOPAD(0x07c, PIN_OUTPUT, 0) /* (F23) MCU_RGMII1_TD0 */ + J721S2_WKUP_IOPAD(0x078, PIN_OUTPUT, 0) /* (G22) MCU_RGMII1_TD1 */ + J721S2_WKUP_IOPAD(0x074, PIN_OUTPUT, 0) /* (E21) MCU_RGMII1_TD2 */ + J721S2_WKUP_IOPAD(0x070, PIN_OUTPUT, 0) /* (E22) MCU_RGMII1_TD3 */ + J721S2_WKUP_IOPAD(0x080, PIN_OUTPUT, 0) /* (F21) MCU_RGMII1_TXC */ + J721S2_WKUP_IOPAD(0x068, PIN_OUTPUT, 0) /* (F22) MCU_RGMII1_TX_CTL */ + >; + }; + + mcu_mdio_pins_default: mcu-mdio-pins-default { + pinctrl-single,pins = < + J721S2_WKUP_IOPAD(0x09c, PIN_OUTPUT, 0) /* (A21) MCU_MDIO0_MDC */ + J721S2_WKUP_IOPAD(0x098, PIN_INPUT, 0) /* (A22) MCU_MDIO0_MDIO */ + >; + }; + + mcu_mcan0_pins_default: mcu-mcan0-pins-default { + pinctrl-single,pins = < + J721S2_WKUP_IOPAD(0x0bc, PIN_INPUT, 0) /* (E28) MCU_MCAN0_RX */ + J721S2_WKUP_IOPAD(0x0b8, PIN_OUTPUT, 0) /* (E27) MCU_MCAN0_TX */ + >; + }; + + mcu_mcan1_pins_default: mcu-mcan1-pins-default { + pinctrl-single,pins = < + J721S2_WKUP_IOPAD(0x0d4, PIN_INPUT, 0) /* (F26) WKUP_GPIO0_5.MCU_MCAN1_RX */ + J721S2_WKUP_IOPAD(0x0d0, PIN_OUTPUT, 0) /* (C23) WKUP_GPIO0_4.MCU_MCAN1_TX*/ + >; + }; + + mcu_i2c1_pins_default: mcu-i2c1-pins-default { + pinctrl-single,pins = < + J721S2_WKUP_IOPAD(0x0e0, PIN_INPUT, 0) /* (F24) WKUP_GPIO0_8.MCU_I2C1_SCL */ + J721S2_WKUP_IOPAD(0x0e4, PIN_INPUT, 0) /* (H26) WKUP_GPIO0_9.MCU_I2C1_SDA */ + >; + }; +}; + +&main_gpio2 { + status = "disabled"; +}; + +&main_gpio4 { + status = "disabled"; +}; + +&main_gpio6 { + status = "disabled"; +}; + +&wkup_gpio0 { + status = "disabled"; +}; + +&wkup_gpio1 { + status = "disabled"; +}; + +&wkup_uart0 { + status = "reserved"; +}; + +&main_uart8 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&main_uart8_pins_default>; + /* Shared with TFA on this platform */ + power-domains = <&k3_pds 357 TI_SCI_PD_SHARED>; +}; + +&main_i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&main_i2c0_pins_default>; + clock-frequency = <400000>; + + exp1: gpio@21 { + compatible = "ti,tca6416"; + reg = <0x21>; + gpio-controller; + #gpio-cells = <2>; + gpio-line-names = "CSI_VIO_SEL", "CSI_SEL_FPC_EXPn", "HDMI_PDn", + "HDMI_LS_OE", "DP0_3V3 _EN", "BOARDID_EEPROM_WP", + "CAN_STB", " ", "GPIO_uSD_PWR_EN", "eDP_ENABLE", + "IO_EXP_PCIe1_M.2_RTSz", "IO_EXP_MCU_RGMII_RSTz", + "IO_EXP_CSI2_EXP_RSTz", " ", "CSI0_B_GPIO1", + "CSI1_B_GPIO1"; + }; +}; + +&main_sdhci0 { + /* Unused */ + status = "disabled"; +}; + +&main_sdhci1 { + /* SD card */ + pinctrl-0 = <&main_mmc1_pins_default>; + pinctrl-names = "default"; + disable-wp; + vmmc-supply = <&vdd_mmc1>; + vqmmc-supply = <&vdd_sd_dv>; +}; + +&mcu_cpsw { + pinctrl-names = "default"; + pinctrl-0 = <&mcu_cpsw_pins_default &mcu_mdio_pins_default>; +}; + +&davinci_mdio { + phy0: ethernet-phy@0 { + reg = <0>; + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; + ti,min-output-impedance; + }; +}; + +&cpsw_port1 { + phy-mode = "rgmii-rxid"; + phy-handle = <&phy0>; +}; + +&mcu_mcan0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mcu_mcan0_pins_default>; + phys = <&transceiver1>; +}; + +&mcu_mcan1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mcu_mcan1_pins_default>; + phys = <&transceiver2>; +}; + +&main_mcan6 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&main_mcan6_pins_default>; + phys = <&transceiver3>; +}; + +&main_mcan7 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&main_mcan7_pins_default>; + phys = <&transceiver4>; +}; -- 2.36.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 8+ messages in thread
* Re: [PATCH V5 3/3] arm64: dts: ti: k3-am68-sk: Add support for AM68 SK base board 2023-01-16 7:14 ` [PATCH V5 3/3] arm64: dts: ti: k3-am68-sk: Add support for AM68 SK base board Sinthu Raja @ 2023-01-16 14:04 ` Vaishnav Achath 0 siblings, 0 replies; 8+ messages in thread From: Vaishnav Achath @ 2023-01-16 14:04 UTC (permalink / raw) To: Sinthu Raja, Nishanth Menon, Tero Kristo, Rob Herring Cc: Vignesh Raghavendra, Krzysztof Kozlowski, linux-arm-kernel, devicetree, linux-kernel, Sinthu Raja On 16/01/23 12:44, Sinthu Raja wrote: > From: Sinthu Raja <sinthu.raja@ti.com> > > The SK architecture comprises of baseboard and a SOM board. The > AM68 Starter Kit's baseboard contains most of the actual connectors, > power supply etc. The System on Module (SoM) is plugged on to the base > board. Therefore, add support for peripherals brought out in the base > board. > > Schematics: https://www.ti.com/lit/zip/SPRR463 > > Signed-off-by: Sinthu Raja <sinthu.raja@ti.com> > --- > > No changes in V4 & V5 > > Changes in V3: > ============= > *Address review comments: > - Remove the unused nodes that are disabled by default. > - Update the gpio regulator node: gpio-regulator-tlv to "regulator-tlv". > > Changes in V2: > ============= > *Address the review comments: > - Update the commit description. > - Update the regulator nodes: fixedregulator to "regulator-" > - Update the commit $subject to align with rest of the commits. > - Drop the blank lines > - Change the node names that are added with underscore("_") with "-" > > V1: https://lore.kernel.org/linux-arm-kernel/20221018123849.23695-4-sinthu.raja@ti.com/ > V2: https://lore.kernel.org/lkml/20221107123852.8063-4-sinthu.raja@ti.com/ > V3: https://lore.kernel.org/lkml/20230110110052.14851-4-sinthu.raja@ti.com/ > V4: https://lore.kernel.org/lkml/20230105151740.29436-4-sinthu.raja@ti.com/ > > arch/arm64/boot/dts/ti/Makefile | 2 + > .../boot/dts/ti/k3-am68-sk-base-board.dts | 335 ++++++++++++++++++ > 2 files changed, 337 insertions(+) > create mode 100644 arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts > > diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile > index cf7c509538a4..1b4e8b573de5 100644 > --- a/arch/arm64/boot/dts/ti/Makefile > +++ b/arch/arm64/boot/dts/ti/Makefile > @@ -12,6 +12,8 @@ dtb-$(CONFIG_ARCH_K3) += k3-am6528-iot2050-basic-pg2.dtb > dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced.dtb > dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced-pg2.dtb > > +dtb-$(CONFIG_ARCH_K3) += k3-am68-sk-base-board.dtb > + > dtb-$(CONFIG_ARCH_K3) += k3-j721e-beagleboneai64.dtb > dtb-$(CONFIG_ARCH_K3) += k3-j721e-common-proc-board.dtb > dtb-$(CONFIG_ARCH_K3) += k3-j721e-sk.dtb > diff --git a/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts b/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts > new file mode 100644 > index 000000000000..2091cd2431fb > --- /dev/null > +++ b/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts > @@ -0,0 +1,335 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Copyright (C) 2023 Texas Instruments Incorporated - https://www.ti.com/ > + * > + * Base Board: https://www.ti.com/lit/zip/SPRR463 > + */ > + > +/dts-v1/; > + > +#include "k3-am68-sk-som.dtsi" > +#include <dt-bindings/net/ti-dp83867.h> > +#include <dt-bindings/phy/phy-cadence.h> > +#include <dt-bindings/phy/phy.h> > +#include <dt-bindings/mux/ti-serdes.h> > + > +/ { > + compatible = "ti,am68-sk", "ti,j721s2"; > + model = "Texas Instruments AM68 SK"; > + > + chosen { > + stdout-path = "serial2:115200n8"; > + }; > + > + aliases { > + serial2 = &main_uart8; > + mmc1 = &main_sdhci1; > + can0 = &mcu_mcan0; > + can1 = &mcu_mcan1; > + can2 = &main_mcan6; > + can3 = &main_mcan7; > + }; > + > + vusb_main: regulator-vusb-main5v0 { > + /* USB MAIN INPUT 5V DC */ > + compatible = "regulator-fixed"; > + regulator-name = "vusb-main5v0"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-always-on; > + regulator-boot-on; > + }; > + > + vsys_3v3: regulator-vsys3v3 { > + /* Output of LM5141 */ > + compatible = "regulator-fixed"; > + regulator-name = "vsys_3v3"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + vin-supply = <&vusb_main>; > + regulator-always-on; > + regulator-boot-on; > + }; > + > + vdd_mmc1: regulator-sd { > + /* Output of TPS22918 */ > + compatible = "regulator-fixed"; > + regulator-name = "vdd_mmc1"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-boot-on; > + enable-active-high; > + vin-supply = <&vsys_3v3>; > + gpio = <&exp1 10 GPIO_ACTIVE_HIGH>; > + }; > + > + vdd_sd_dv: regulator-tlv71033 { > + /* Output of TLV71033 */ > + compatible = "regulator-gpio"; > + regulator-name = "tlv71033"; > + pinctrl-names = "default"; > + pinctrl-0 = <&vdd_sd_dv_pins_default>; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + regulator-boot-on; > + vin-supply = <&vsys_3v3>; > + gpios = <&main_gpio0 49 GPIO_ACTIVE_HIGH>; > + states = <1800000 0x0>, > + <3300000 0x1>; > + }; > + > + vsys_io_1v8: regulator-vsys-io-1v8 { > + compatible = "regulator-fixed"; > + regulator-name = "vsys_io_1v8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-always-on; > + regulator-boot-on; > + }; > + > + vsys_io_1v2: regulator-vsys-io-1v2 { > + compatible = "regulator-fixed"; > + regulator-name = "vsys_io_1v2"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + regulator-always-on; > + regulator-boot-on; > + }; > + > + transceiver1: can-phy0 { > + compatible = "ti,tcan1042"; > + #phy-cells = <0>; > + max-bitrate = <5000000>; > + }; > + > + transceiver2: can-phy1 { > + compatible = "ti,tcan1042"; > + #phy-cells = <0>; > + max-bitrate = <5000000>; > + }; > + > + transceiver3: can-phy2 { > + compatible = "ti,tcan1042"; > + #phy-cells = <0>; > + max-bitrate = <5000000>; > + }; > + > + transceiver4: can-phy3 { > + compatible = "ti,tcan1042"; > + #phy-cells = <0>; > + max-bitrate = <5000000>; > + }; > +}; > + > +&main_pmx0 { > + main_uart8_pins_default: main-uart8-pins-default { > + pinctrl-single,pins = < > + J721S2_IOPAD(0x0d0, PIN_INPUT, 11) /* (AF26) SPI0_CS1.UART8_RXD */ > + J721S2_IOPAD(0x0d4, PIN_OUTPUT, 11) /* (AH27) SPI0_CLK.UART8_TXD */ > + >; > + }; > + > + main_i2c0_pins_default: main-i2c0-pins-default { > + pinctrl-single,pins = < > + J721S2_IOPAD(0x0e0, PIN_INPUT, 0) /* (AH25) I2C0_SCL */ > + J721S2_IOPAD(0x0e4, PIN_INPUT, 0) /* (AE24) I2C0_SDA */ > + >; > + }; > + > + main_mmc1_pins_default: main-mmc1-pins-default { > + pinctrl-single,pins = < > + J721S2_IOPAD(0x104, PIN_INPUT, 0) /* (P23) MMC1_CLK */ > + J721S2_IOPAD(0x108, PIN_INPUT, 0) /* (N24) MMC1_CMD */ > + J721S2_IOPAD(0x0fc, PIN_INPUT, 0) /* (M23) MMC1_DAT0 */ > + J721S2_IOPAD(0x0f8, PIN_INPUT, 0) /* (P24) MMC1_DAT1 */ > + J721S2_IOPAD(0x0f4, PIN_INPUT, 0) /* (R24) MMC1_DAT2 */ > + J721S2_IOPAD(0x0f0, PIN_INPUT, 0) /* (R22) MMC1_DAT3 */ > + J721S2_IOPAD(0x0e8, PIN_INPUT, 8) /* (AE25) TIMER_IO0.MMC1_SDCD */ > + >; > + }; > + > + vdd_sd_dv_pins_default: vdd-sd-dv-pins-default { > + pinctrl-single,pins = < > + J721S2_IOPAD(0x0c4, PIN_INPUT, 7) /* (AB26) ECAP0_IN_APWM_OUT.GPIO0_49 */ > + >; > + }; > + > + main_usbss0_pins_default: main-usbss0-pins-default { > + pinctrl-single,pins = < > + J721S2_IOPAD(0x0ec, PIN_OUTPUT, 6) /* (AG25) TIMER_IO1.USB0_DRVVBUS */ > + >; > + }; > + > + main_mcan6_pins_default: main-mcan6-pins-default { > + pinctrl-single,pins = < > + J721S2_IOPAD(0x098, PIN_INPUT, 0) /* (V25) MCASP0_AXR10.MCAN6_RX */ > + J721S2_IOPAD(0x094, PIN_INPUT, 0) /* (AA25) MCASP0_AXR9.MCAN6_TX */ > + >; > + }; > + > + main_mcan7_pins_default: main-mcan7-pins-default { > + pinctrl-single,pins = < > + J721S2_IOPAD(0x0a0, PIN_INPUT, 0) /* (AB25) MCASP0_AXR12.MCAN7_RX */ > + J721S2_IOPAD(0x09c, PIN_INPUT, 0) /* (T24) MCASP0_AXR11.MCAN7_TX */ > + >; > + }; > +}; > + > +&wkup_pmx0 { > + mcu_cpsw_pins_default: mcu-cpsw-pins-default { > + pinctrl-single,pins = < > + J721S2_WKUP_IOPAD(0x094, PIN_INPUT, 0) /* (B22) MCU_RGMII1_RD0 */ > + J721S2_WKUP_IOPAD(0x090, PIN_INPUT, 0) /* (B21) MCU_RGMII1_RD1 */ > + J721S2_WKUP_IOPAD(0x08c, PIN_INPUT, 0) /* (C22) MCU_RGMII1_RD2 */ > + J721S2_WKUP_IOPAD(0x088, PIN_INPUT, 0) /* (D23) MCU_RGMII1_RD3 */ > + J721S2_WKUP_IOPAD(0x084, PIN_INPUT, 0) /* (D22) MCU_RGMII1_RXC */ > + J721S2_WKUP_IOPAD(0x06c, PIN_INPUT, 0) /* (E23) MCU_RGMII1_RX_CTL */ > + J721S2_WKUP_IOPAD(0x07c, PIN_OUTPUT, 0) /* (F23) MCU_RGMII1_TD0 */ > + J721S2_WKUP_IOPAD(0x078, PIN_OUTPUT, 0) /* (G22) MCU_RGMII1_TD1 */ > + J721S2_WKUP_IOPAD(0x074, PIN_OUTPUT, 0) /* (E21) MCU_RGMII1_TD2 */ > + J721S2_WKUP_IOPAD(0x070, PIN_OUTPUT, 0) /* (E22) MCU_RGMII1_TD3 */ > + J721S2_WKUP_IOPAD(0x080, PIN_OUTPUT, 0) /* (F21) MCU_RGMII1_TXC */ > + J721S2_WKUP_IOPAD(0x068, PIN_OUTPUT, 0) /* (F22) MCU_RGMII1_TX_CTL */ > + >; > + }; > + > + mcu_mdio_pins_default: mcu-mdio-pins-default { > + pinctrl-single,pins = < > + J721S2_WKUP_IOPAD(0x09c, PIN_OUTPUT, 0) /* (A21) MCU_MDIO0_MDC */ > + J721S2_WKUP_IOPAD(0x098, PIN_INPUT, 0) /* (A22) MCU_MDIO0_MDIO */ > + >; > + }; > + > + mcu_mcan0_pins_default: mcu-mcan0-pins-default { > + pinctrl-single,pins = < > + J721S2_WKUP_IOPAD(0x0bc, PIN_INPUT, 0) /* (E28) MCU_MCAN0_RX */ > + J721S2_WKUP_IOPAD(0x0b8, PIN_OUTPUT, 0) /* (E27) MCU_MCAN0_TX */ > + >; > + }; > + > + mcu_mcan1_pins_default: mcu-mcan1-pins-default { > + pinctrl-single,pins = < > + J721S2_WKUP_IOPAD(0x0d4, PIN_INPUT, 0) /* (F26) WKUP_GPIO0_5.MCU_MCAN1_RX */ > + J721S2_WKUP_IOPAD(0x0d0, PIN_OUTPUT, 0) /* (C23) WKUP_GPIO0_4.MCU_MCAN1_TX*/ > + >; > + }; > + > + mcu_i2c1_pins_default: mcu-i2c1-pins-default { > + pinctrl-single,pins = < > + J721S2_WKUP_IOPAD(0x0e0, PIN_INPUT, 0) /* (F24) WKUP_GPIO0_8.MCU_I2C1_SCL */ > + J721S2_WKUP_IOPAD(0x0e4, PIN_INPUT, 0) /* (H26) WKUP_GPIO0_9.MCU_I2C1_SDA */ > + >; > + }; > +}; > + > +&main_gpio2 { > + status = "disabled"; > +}; > + > +&main_gpio4 { > + status = "disabled"; > +}; > + > +&main_gpio6 { > + status = "disabled"; > +}; > + > +&wkup_gpio0 { > + status = "disabled"; > +}; > + > +&wkup_gpio1 { > + status = "disabled"; > +}; > + > +&wkup_uart0 { > + status = "reserved"; > +}; > + > +&main_uart8 { > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&main_uart8_pins_default>; > + /* Shared with TFA on this platform */ > + power-domains = <&k3_pds 357 TI_SCI_PD_SHARED>; > +}; > + > +&main_i2c0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&main_i2c0_pins_default>; > + clock-frequency = <400000>; > + > + exp1: gpio@21 { > + compatible = "ti,tca6416"; > + reg = <0x21>; > + gpio-controller; > + #gpio-cells = <2>; > + gpio-line-names = "CSI_VIO_SEL", "CSI_SEL_FPC_EXPn", "HDMI_PDn", > + "HDMI_LS_OE", "DP0_3V3 _EN", "BOARDID_EEPROM_WP", > + "CAN_STB", " ", "GPIO_uSD_PWR_EN", "eDP_ENABLE", > + "IO_EXP_PCIe1_M.2_RTSz", "IO_EXP_MCU_RGMII_RSTz", > + "IO_EXP_CSI2_EXP_RSTz", " ", "CSI0_B_GPIO1", > + "CSI1_B_GPIO1"; > + }; > +}; > + > +&main_sdhci0 { > + /* Unused */ > + status = "disabled"; > +}; > + > +&main_sdhci1 { > + /* SD card */ > + pinctrl-0 = <&main_mmc1_pins_default>; > + pinctrl-names = "default"; > + disable-wp; > + vmmc-supply = <&vdd_mmc1>; > + vqmmc-supply = <&vdd_sd_dv>; > +}; > + > +&mcu_cpsw { > + pinctrl-names = "default"; > + pinctrl-0 = <&mcu_cpsw_pins_default &mcu_mdio_pins_default>; > +}; > + > +&davinci_mdio { > + phy0: ethernet-phy@0 { > + reg = <0>; > + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; > + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; > + ti,min-output-impedance; > + }; > +}; > + > +&cpsw_port1 { > + phy-mode = "rgmii-rxid"; > + phy-handle = <&phy0>; > +}; > + > +&mcu_mcan0 { > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&mcu_mcan0_pins_default>; > + phys = <&transceiver1>; > +}; > + > +&mcu_mcan1 { > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&mcu_mcan1_pins_default>; > + phys = <&transceiver2>; > +}; > + > +&main_mcan6 { > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&main_mcan6_pins_default>; > + phys = <&transceiver3>; > +}; > + > +&main_mcan7 { > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&main_mcan7_pins_default>; > + phys = <&transceiver4>; Tested-by: Vaishnav Achath <vaishnav.a@ti.com> > +}; -- Regards, Vaishnav _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH V5 0/3] AM68 SK: Add initial support 2023-01-16 7:14 [PATCH V5 0/3] AM68 SK: Add initial support Sinthu Raja ` (2 preceding siblings ...) 2023-01-16 7:14 ` [PATCH V5 3/3] arm64: dts: ti: k3-am68-sk: Add support for AM68 SK base board Sinthu Raja @ 2023-01-16 11:17 ` Neha Malcom Francis 2023-01-23 17:39 ` Vignesh Raghavendra 4 siblings, 0 replies; 8+ messages in thread From: Neha Malcom Francis @ 2023-01-16 11:17 UTC (permalink / raw) To: Sinthu Raja, Nishanth Menon, Tero Kristo, Rob Herring Cc: Vignesh Raghavendra, Krzysztof Kozlowski, linux-arm-kernel, devicetree, linux-kernel, Sinthu Raja Hi Sinthu On 16/01/23 12:44, Sinthu Raja wrote: > From: Sinthu Raja <sinthu.raja@ti.com> > > Hi All, > This series of patches add support for AM68 Starter kit(SK). AM68 SK > is a low cost, small form factor board designed for TI’s AM68 SoC. > > Refer below link to AM68 Technical Reference Manual for further details: > http://www.ti.com/lit/pdf/spruj28 > > Design files can be referrred from https://www.ti.com/lit/zip/SPRR463 > > Changes in V5: > ============= > Address review comments: > - Remove the unessential comment. > - Remove alignment property from secure-ddr node, as no memory is allocated out > of this region. > > Changes in V4: > ============= > Repost after rebasing to 6.2 rc1 > > Changes in V3: > ============== > Address all the review comments and the changes are captured in separate patches. > - Remove the unused nodes that are disabled by default. > - Update the gpio regulator node: gpio-regulator-tlv to "regulator-tlv". > > V1: https://lore.kernel.org/linux-arm-kernel/20221018123849.23695-1-sinthu.raja@ti.com/t/#mbe43b02221733bb6eb06b203359e90ec08406afc > V2: https://lore.kernel.org/lkml/20221107123852.8063-1-sinthu.raja@ti.com/ > V3: https://lore.kernel.org/lkml/20230110110052.14851-1-sinthu.raja@ti.com/ > V4: https://lore.kernel.org/lkml/20230105151740.29436-1-sinthu.raja@ti.com/ > > Sinthu Raja (3): > dt-bindings: arm: ti: Add binding for AM68 SK > arm64: dts: ti: Add initial support for AM68 SK System on Module > arm64: dts: ti: k3-am68-sk: Add support for AM68 SK base board > > .../devicetree/bindings/arm/ti/k3.yaml | 1 + > arch/arm64/boot/dts/ti/Makefile | 2 + > .../boot/dts/ti/k3-am68-sk-base-board.dts | 335 ++++++++++++++++++ > arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi | 29 ++ > 4 files changed, 367 insertions(+) > create mode 100644 arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts > create mode 100644 arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi > For the series: Reviewed-by: Neha Malcom Francis <n-francis@ti.com> -- Thanking You Neha Malcom Francis _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH V5 0/3] AM68 SK: Add initial support 2023-01-16 7:14 [PATCH V5 0/3] AM68 SK: Add initial support Sinthu Raja ` (3 preceding siblings ...) 2023-01-16 11:17 ` [PATCH V5 0/3] AM68 SK: Add initial support Neha Malcom Francis @ 2023-01-23 17:39 ` Vignesh Raghavendra 4 siblings, 0 replies; 8+ messages in thread From: Vignesh Raghavendra @ 2023-01-23 17:39 UTC (permalink / raw) To: Nishanth Menon, Tero Kristo, Sinthu Raja, Rob Herring Cc: Vignesh Raghavendra, linux-kernel, linux-arm-kernel, Sinthu Raja, Krzysztof Kozlowski, devicetree Hi Sinthu Raja, On Mon, 16 Jan 2023 12:44:43 +0530, Sinthu Raja wrote: > From: Sinthu Raja <sinthu.raja@ti.com> > > Hi All, > This series of patches add support for AM68 Starter kit(SK). AM68 SK > is a low cost, small form factor board designed for TI’s AM68 SoC. > > Refer below link to AM68 Technical Reference Manual for further details: > http://www.ti.com/lit/pdf/spruj28 > > [...] I have applied the following to branch ti-k3-dts-next on [1]. Thank you! [1/3] dt-bindings: arm: ti: Add binding for AM68 SK commit: 73b1c4f5f53e531f75d4b65dec4784cf67e685f2 [2/3] arm64: dts: ti: Add initial support for AM68 SK System on Module commit: 2b6277b76d42cbb781c558ea982e23cd770dd363 [3/3] arm64: dts: ti: k3-am68-sk: Add support for AM68 SK base board commit: a266c180b398eab5030bdcf2d1bbdc62fb7fc9c1 All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent up the chain during the next merge window (or sooner if it is a relevant bug fix), however if problems are discovered then the patch may be dropped or reverted. You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed. If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced. Please add any relevant lists and maintainers to the CCs when replying to this mail. [1] https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux.git -- Vignesh _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2023-01-23 17:41 UTC | newest] Thread overview: 8+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2023-01-16 7:14 [PATCH V5 0/3] AM68 SK: Add initial support Sinthu Raja 2023-01-16 7:14 ` [PATCH V5 1/3] dt-bindings: arm: ti: Add binding for AM68 SK Sinthu Raja 2023-01-16 7:14 ` [PATCH V5 2/3] arm64: dts: ti: Add initial support for AM68 SK System on Module Sinthu Raja 2023-01-16 14:02 ` Vaishnav Achath 2023-01-16 7:14 ` [PATCH V5 3/3] arm64: dts: ti: k3-am68-sk: Add support for AM68 SK base board Sinthu Raja 2023-01-16 14:04 ` Vaishnav Achath 2023-01-16 11:17 ` [PATCH V5 0/3] AM68 SK: Add initial support Neha Malcom Francis 2023-01-23 17:39 ` Vignesh Raghavendra
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).