[PATCH v6 0/6] arm64: ti: Enable audio on AM62 and AM62A

[PATCH v6 0/6] arm64: ti: Enable audio on AM62 and AM62A

[Jai Luthra]

This patch series adds support for audio via headphone jack on SK-AM62
and SK-AM62A boards. The jack is wired to TLV320AIC3106 (codec), which
is connected to McASP1 (serializer) on the SoC.

The TRRS 3.5mm jack can be used for simultaneous playback and recording.

Signed-off-by: Jai Luthra <j-luthra@ti.com>
---
Changes in v6:
- Use generic node names (audio-controller@) for McASP
- Fix labels, indentation and spacing issues
- For SK-AM62A:
	- Remove redundant status property from codec
	- Add a note in commit message about missing DVDD regulator
	- Supply OCMV level manually to the codec

Link to v5: https://lore.kernel.org/r/20230313-mcasp_upstream-v5-0-d6844707aa8a@ti.com

---
Jai Luthra (5):
      arm64: defconfig: Enable audio drivers for TI K3 SoCs
      arm64: dts: ti: k3-am625-sk: Enable audio on AM62 SK
      arm64: dts: ti: k3-am62a-main: Add nodes for McASP
      arm64: dts: ti: k3-am62a7-sk: Split vcc_3v3 regulators
      arm64: dts: ti: k3-am62a7-sk: Enable audio on AM62A

Jayesh Choudhary (1):
      arm64: dts: ti: k3-am62-main: Add McASP nodes

 arch/arm64/boot/dts/ti/k3-am62-main.dtsi  | 60 ++++++++++++++++++++
 arch/arm64/boot/dts/ti/k3-am625-sk.dts    | 88 +++++++++++++++++++++++++++++
 arch/arm64/boot/dts/ti/k3-am62a-main.dtsi | 60 ++++++++++++++++++++
 arch/arm64/boot/dts/ti/k3-am62a7-sk.dts   | 92 ++++++++++++++++++++++++++++++-
 arch/arm64/configs/defconfig              |  2 +
 5 files changed, 300 insertions(+), 2 deletions(-)
---
base-commit: 24469a0e5052ba01a35a15f104717a82b7a4798b
change-id: 20230313-mcasp_upstream-0e137013059b

Best regards,
-- 
Jai Luthra <j-luthra@ti.com>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v6 1/6] arm64: defconfig: Enable audio drivers for TI K3 SoCs

[Jai Luthra]

TI's K3 platform uses McASP as the digital audio interface on the SoCs.
AM62x and AM62A based starter kits also use the TLV320AIC3106 codec with
a 3.5mm jack for analog audio input and output.

Signed-off-by: Jai Luthra <j-luthra@ti.com>
---
 arch/arm64/configs/defconfig | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 7790ee42c68a..7e0ce1833904 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -898,6 +898,8 @@ CONFIG_SND_SOC_LPASS_WSA_MACRO=m
 CONFIG_SND_SOC_LPASS_VA_MACRO=m
 CONFIG_SND_SOC_LPASS_RX_MACRO=m
 CONFIG_SND_SOC_LPASS_TX_MACRO=m
+CONFIG_SND_SOC_DAVINCI_MCASP=m
+CONFIG_SND_SOC_TLV320AIC3X_I2C=m
 CONFIG_SND_SIMPLE_CARD=m
 CONFIG_SND_AUDIO_GRAPH_CARD=m
 CONFIG_SND_AUDIO_GRAPH_CARD2=m

-- 
2.39.2

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v6 2/6] arm64: dts: ti: k3-am62-main: Add McASP nodes

[Jai Luthra]

From: Jayesh Choudhary <j-choudhary@ti.com>

Add the nodes for McASP 0-2.

Use the audio-friendly 96MHz main_1_hsdivout6_clk as clock parent
instead of the default 100Mhz main_2_hsdivout8_clk source.

Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am62-main.dtsi | 60 ++++++++++++++++++++++++++++++++
 1 file changed, 60 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am62-main.dtsi b/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
index ea683fd77d6a..c52c23ac409a 100644
--- a/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
@@ -787,4 +787,64 @@ epwm2: pwm@23020000 {
 		clock-names = "tbclk", "fck";
 		status = "disabled";
 	};
+
+	mcasp0: audio-controller@2b00000 {
+		compatible = "ti,am33xx-mcasp-audio";
+		reg = <0x00 0x02b00000 0x00 0x2000>,
+		      <0x00 0x02b08000 0x00 0x400>;
+		reg-names = "mpu", "dat";
+		interrupts = <GIC_SPI 236 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 235 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "tx", "rx";
+
+		dmas = <&main_bcdma 0 0xc500 0>, <&main_bcdma 0 0x4500 0>;
+		dma-names = "tx", "rx";
+
+		clocks = <&k3_clks 190 0>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 190 0>;
+		assigned-clock-parents = <&k3_clks 190 2>;
+		power-domains = <&k3_pds 190 TI_SCI_PD_EXCLUSIVE>;
+		status = "disabled";
+	};
+
+	mcasp1: audio-controller@2b10000 {
+		compatible = "ti,am33xx-mcasp-audio";
+		reg = <0x00 0x02b10000 0x00 0x2000>,
+		      <0x00 0x02b18000 0x00 0x400>;
+		reg-names = "mpu", "dat";
+		interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 237 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "tx", "rx";
+
+		dmas = <&main_bcdma 0 0xc501 0>, <&main_bcdma 0 0x4501 0>;
+		dma-names = "tx", "rx";
+
+		clocks = <&k3_clks 191 0>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 191 0>;
+		assigned-clock-parents = <&k3_clks 191 2>;
+		power-domains = <&k3_pds 191 TI_SCI_PD_EXCLUSIVE>;
+		status = "disabled";
+	};
+
+	mcasp2: audio-controller@2b20000 {
+		compatible = "ti,am33xx-mcasp-audio";
+		reg = <0x00 0x02b20000 0x00 0x2000>,
+		      <0x00 0x02b28000 0x00 0x400>;
+		reg-names = "mpu", "dat";
+		interrupts = <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "tx", "rx";
+
+		dmas = <&main_bcdma 0 0xc502 0>, <&main_bcdma 0 0x4502 0>;
+		dma-names = "tx", "rx";
+
+		clocks = <&k3_clks 192 0>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 192 0>;
+		assigned-clock-parents = <&k3_clks 192 2>;
+		power-domains = <&k3_pds 192 TI_SCI_PD_EXCLUSIVE>;
+		status = "disabled";
+	};
 };

-- 
2.39.2

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v6 3/6] arm64: dts: ti: k3-am625-sk: Enable audio on AM62 SK

[Jai Luthra]

Add nodes for audio codec and sound card, enable the audio serializer
(McASP1) under use and update pinmux.

Signed-off-by: Jai Luthra <j-luthra@ti.com>
Reviewed-by: Jayesh Choudhary <j-choudhary@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am625-sk.dts | 88 ++++++++++++++++++++++++++++++++++
 1 file changed, 88 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am625-sk.dts b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
index 6bc7d63cf52f..2727a3c81e93 100644
--- a/arch/arm64/boot/dts/ti/k3-am625-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
@@ -141,6 +141,52 @@ vdd_sd_dv: regulator-4 {
 			 <3300000 0x1>;
 	};
 
+	vcc_1v8: regulator-5 {
+		/* output of TPS6282518DMQ */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_3v3_sys>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	tlv320_mclk: clk-0 {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <12288000>;
+	};
+
+	codec_audio: sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "AM62x-SKEVM";
+		simple-audio-card,widgets =
+			"Headphone",	"Headphone Jack",
+			"Line",		"Line In",
+			"Microphone",	"Microphone Jack";
+		simple-audio-card,routing =
+			"Headphone Jack",	"HPLOUT",
+			"Headphone Jack",	"HPROUT",
+			"LINE1L",		"Line In",
+			"LINE1R",		"Line In",
+			"MIC3R",		"Microphone Jack",
+			"Microphone Jack",	"Mic Bias";
+		simple-audio-card,format = "dsp_b";
+		simple-audio-card,bitclock-master = <&sound_master>;
+		simple-audio-card,frame-master = <&sound_master>;
+		simple-audio-card,bitclock-inversion;
+
+		simple-audio-card,cpu {
+			sound-dai = <&mcasp1>;
+		};
+
+		sound_master: simple-audio-card,codec {
+			sound-dai = <&tlv320aic3106>;
+			clocks = <&tlv320_mclk>;
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
@@ -292,6 +338,15 @@ main_usb1_pins_default: main-usb1-pins-default {
 			AM62X_IOPAD(0x0258, PIN_OUTPUT, 0) /* (F18) USB1_DRVVBUS */
 		>;
 	};
+
+	main_mcasp1_pins_default: main-mcasp1-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x090, PIN_INPUT, 2) /* (M24) GPMC0_BE0N_CLE.MCASP1_ACLKX */
+			AM62X_IOPAD(0x098, PIN_INPUT, 2) /* (U23) GPMC0_WAIT0.MCASP1_AFSX */
+			AM62X_IOPAD(0x08c, PIN_OUTPUT, 2) /* (L25) GPMC0_WEN.MCASP1_AXR0 */
+			AM62X_IOPAD(0x084, PIN_INPUT, 2) /* (L23) GPMC0_ADVN_ALE.MCASP1_AXR2 */
+		>;
+	};
 };
 
 &wkup_uart0 {
@@ -349,6 +404,19 @@ exp1: gpio@22 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&main_gpio1_ioexp_intr_pins_default>;
 	};
+
+	tlv320aic3106: audio-codec@1b {
+		#sound-dai-cells = <0>;
+		compatible = "ti,tlv320aic3106";
+		reg = <0x1b>;
+		ai3x-micbias-vg = <1>;	/* 2.0V */
+
+		/* Regulators */
+		AVDD-supply = <&vcc_3v3_sys>;
+		IOVDD-supply = <&vcc_3v3_sys>;
+		DRVDD-supply = <&vcc_3v3_sys>;
+		DVDD-supply = <&vcc_1v8>;
+	};
 };
 
 &sdhci0 {
@@ -406,6 +474,26 @@ cpsw3g_phy1: ethernet-phy@1 {
 	};
 };
 
+&mcasp1 {
+	status = "okay";
+	#sound-dai-cells = <0>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_mcasp1_pins_default>;
+
+	op-mode = <0>;          /* MCASP_IIS_MODE */
+	tdm-slots = <2>;
+
+	serial-dir = <  /* 0: INACTIVE, 1: TX, 2: RX */
+	       1 0 2 0
+	       0 0 0 0
+	       0 0 0 0
+	       0 0 0 0
+	>;
+	tx-num-evt = <32>;
+	rx-num-evt = <32>;
+};
+
 &mailbox0_cluster0 {
 	mbox_m4_0: mbox-m4-0 {
 		ti,mbox-rx = <0 0 0>;

-- 
2.39.2

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v6 4/6] arm64: dts: ti: k3-am62a-main: Add nodes for McASP

[Jai Luthra]

Same as AM62, AM62A has three instances of McASP which can be used for
transmitting or receiving digital audio in various formats.

Signed-off-by: Jai Luthra <j-luthra@ti.com>
Reviewed-by: Jayesh Choudhary <j-choudhary@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am62a-main.dtsi | 60 +++++++++++++++++++++++++++++++
 1 file changed, 60 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi b/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi
index 393a1a40b68b..50e4fcb1d678 100644
--- a/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi
@@ -660,4 +660,64 @@ ecap2: pwm@23120000 {
 		clock-names = "fck";
 		status = "disabled";
 	};
+
+	mcasp0: audio-controller@2b00000 {
+		compatible = "ti,am33xx-mcasp-audio";
+		reg = <0x00 0x02b00000 0x00 0x2000>,
+		      <0x00 0x02b08000 0x00 0x400>;
+		reg-names = "mpu", "dat";
+		interrupts = <GIC_SPI 236 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 235 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "tx", "rx";
+
+		dmas = <&main_bcdma 0 0xc500 0>, <&main_bcdma 0 0x4500 0>;
+		dma-names = "tx", "rx";
+
+		clocks = <&k3_clks 190 0>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 190 0>;
+		assigned-clock-parents = <&k3_clks 190 2>;
+		power-domains = <&k3_pds 190 TI_SCI_PD_EXCLUSIVE>;
+		status = "disabled";
+	};
+
+	mcasp1: audio-controller@2b10000 {
+		compatible = "ti,am33xx-mcasp-audio";
+		reg = <0x00 0x02b10000 0x00 0x2000>,
+		      <0x00 0x02b18000 0x00 0x400>;
+		reg-names = "mpu", "dat";
+		interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 237 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "tx", "rx";
+
+		dmas = <&main_bcdma 0 0xc501 0>, <&main_bcdma 0 0x4501 0>;
+		dma-names = "tx", "rx";
+
+		clocks = <&k3_clks 191 0>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 191 0>;
+		assigned-clock-parents = <&k3_clks 191 2>;
+		power-domains = <&k3_pds 191 TI_SCI_PD_EXCLUSIVE>;
+		status = "disabled";
+	};
+
+	mcasp2: audio-controller@2b20000 {
+		compatible = "ti,am33xx-mcasp-audio";
+		reg = <0x00 0x02b20000 0x00 0x2000>,
+		      <0x00 0x02b28000 0x00 0x400>;
+		reg-names = "mpu", "dat";
+		interrupts = <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "tx", "rx";
+
+		dmas = <&main_bcdma 0 0xc502 0>, <&main_bcdma 0 0x4502 0>;
+		dma-names = "tx", "rx";
+
+		clocks = <&k3_clks 192 0>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 192 0>;
+		assigned-clock-parents = <&k3_clks 192 2>;
+		power-domains = <&k3_pds 192 TI_SCI_PD_EXCLUSIVE>;
+		status = "disabled";
+	};
 };

-- 
2.39.2

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v6 5/6] arm64: dts: ti: k3-am62a7-sk: Split vcc_3v3 regulators

[Jai Luthra]

VCC_3V3_MAIN is the output of LM5141-Q1, and it serves as an input to
TPS22965DSGT which produces VCC_3V3_SYS.

Signed-off-by: Jai Luthra <j-luthra@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 15 +++++++++++++--
 1 file changed, 13 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
index 5c9012141ee2..063e69e45163 100644
--- a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
@@ -76,10 +76,10 @@ vcc_5v0: regulator-1 {
 		regulator-boot-on;
 	};
 
-	vcc_3v3_sys: regulator-2 {
+	vcc_3v3_main: regulator-2 {
 		/* output of LM5141-Q1 */
 		compatible = "regulator-fixed";
-		regulator-name = "vcc_3v3_sys";
+		regulator-name = "vcc_3v3_main";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 		vin-supply = <&vmain_pd>;
@@ -98,6 +98,17 @@ vdd_mmc1: regulator-3 {
 		gpio = <&exp1 3 GPIO_ACTIVE_HIGH>;
 	};
 
+	vcc_3v3_sys: regulator-4 {
+		/* output of TPS222965DSGT */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_3v3_sys";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_3v3_main>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";

-- 
2.39.2

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v6 6/6] arm64: dts: ti: k3-am62a7-sk: Enable audio on AM62A

[Jai Luthra]

Add nodes for audio codec and sound card, enable the audio serializer
(McASP1) under use and update pinmux.

The codec (TLV320AIC3106) is also supplied with a DVDD 1.8V supply from
the PMIC (TPS6593x) on the SK. As the PMIC driver and devicetree node is
missing, skip describing DVDD for now and manually set the OCMV voltage.

Signed-off-by: Jai Luthra <j-luthra@ti.com>
Reviewed-by: Jayesh Choudhary <j-choudhary@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 77 +++++++++++++++++++++++++++++++++
 1 file changed, 77 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
index 063e69e45163..2ee894340be1 100644
--- a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
@@ -122,6 +122,41 @@ led-0 {
 			default-state = "off";
 		};
 	};
+
+	tlv320_mclk: clk-0 {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <12288000>;
+	};
+
+	codec_audio: sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "AM62Ax-SKEVM";
+		simple-audio-card,widgets =
+			"Headphone",	"Headphone Jack",
+			"Line",		"Line In",
+			"Microphone",	"Microphone Jack";
+		simple-audio-card,routing =
+			"Headphone Jack",	"HPLOUT",
+			"Headphone Jack",	"HPROUT",
+			"LINE1L",		"Line In",
+			"LINE1R",		"Line In",
+			"MIC3R",		"Microphone Jack",
+			"Microphone Jack",	"Mic Bias";
+		simple-audio-card,format = "dsp_b";
+		simple-audio-card,bitclock-master = <&sound_master>;
+		simple-audio-card,frame-master = <&sound_master>;
+		simple-audio-card,bitclock-inversion;
+
+		simple-audio-card,cpu {
+			sound-dai = <&mcasp1>;
+		};
+
+		sound_master: simple-audio-card,codec {
+			sound-dai = <&tlv320aic3106>;
+			clocks = <&tlv320_mclk>;
+		};
+	};
 };
 
 &main_pmx0 {
@@ -200,6 +235,15 @@ AM62AX_IOPAD(0x130, PIN_INPUT, 0) /* (AB17) RGMII1_TXC */
 			AM62AX_IOPAD(0x12c, PIN_INPUT, 0) /* (W16) RGMII1_TX_CTL */
 		>;
 	};
+
+	main_mcasp1_pins_default: main-mcasp1-pins-default {
+		pinctrl-single,pins = <
+			AM62AX_IOPAD(0x090, PIN_INPUT, 2) /* (L19) GPMC0_BE0n_CLE.MCASP1_ACLKX */
+			AM62AX_IOPAD(0x098, PIN_INPUT, 2) /* (R18) GPMC0_WAIT0.MCASP1_AFSX */
+			AM62AX_IOPAD(0x08c, PIN_OUTPUT, 2) /* (K19) GPMC0_WEn.MCASP1_AXR0 */
+			AM62AX_IOPAD(0x084, PIN_INPUT, 2) /* (L18) GPMC0_ADVn_ALE.MCASP1_AXR2 */
+		>;
+	};
 };
 
 &main_i2c0 {
@@ -234,6 +278,19 @@ exp1: gpio@22 {
 				   "MCASP1_FET_SEL", "UART1_FET_SEL",
 				   "PD_I2C_IRQ", "IO_EXP_TEST_LED";
 	};
+
+	tlv320aic3106: audio-codec@1b {
+		#sound-dai-cells = <0>;
+		compatible = "ti,tlv320aic3106";
+		reg = <0x1b>;
+		ai3x-micbias-vg = <1>;	/* 2.0V */
+		ai3x-ocmv = <1>;	/* 1.5V */
+
+		/* Regulators */
+		AVDD-supply = <&vcc_3v3_sys>;
+		IOVDD-supply = <&vcc_3v3_sys>;
+		DRVDD-supply = <&vcc_3v3_sys>;
+	};
 };
 
 &sdhci1 {
@@ -302,3 +359,23 @@ cpsw3g_phy0: ethernet-phy@0 {
 		ti,min-output-impedance;
 	};
 };
+
+&mcasp1 {
+	status = "okay";
+	#sound-dai-cells = <0>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_mcasp1_pins_default>;
+
+	op-mode = <0>;          /* MCASP_IIS_MODE */
+	tdm-slots = <2>;
+
+	serial-dir = <  /* 0: INACTIVE, 1: TX, 2: RX */
+	       1 0 2 0
+	       0 0 0 0
+	       0 0 0 0
+	       0 0 0 0
+	>;
+	tx-num-evt = <32>;
+	rx-num-evt = <32>;
+};

-- 
2.39.2

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v6 1/6] arm64: defconfig: Enable audio drivers for TI K3 SoCs

[Devarsh Thakkar]

Hi Jai,

Thanks for the patch.

On 15/03/23 14:33, Jai Luthra wrote:
> TI's K3 platform uses McASP as the digital audio interface on the SoCs.
> AM62x and AM62A based starter kits also use the TLV320AIC3106 codec with
> a 3.5mm jack for analog audio input and output.
> 
> Signed-off-by: Jai Luthra <j-luthra@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
> ---
>  arch/arm64/configs/defconfig | 2 ++
>  1 file changed, 2 insertions(+)
> 
> diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
> index 7790ee42c68a..7e0ce1833904 100644
> --- a/arch/arm64/configs/defconfig
> +++ b/arch/arm64/configs/defconfig
> @@ -898,6 +898,8 @@ CONFIG_SND_SOC_LPASS_WSA_MACRO=m
>  CONFIG_SND_SOC_LPASS_VA_MACRO=m
>  CONFIG_SND_SOC_LPASS_RX_MACRO=m
>  CONFIG_SND_SOC_LPASS_TX_MACRO=m
> +CONFIG_SND_SOC_DAVINCI_MCASP=m
> +CONFIG_SND_SOC_TLV320AIC3X_I2C=m
>  CONFIG_SND_SIMPLE_CARD=m
>  CONFIG_SND_AUDIO_GRAPH_CARD=m
>  CONFIG_SND_AUDIO_GRAPH_CARD2=m
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v6 5/6] arm64: dts: ti: k3-am62a7-sk: Split vcc_3v3 regulators

[Devarsh Thakkar]

Hi Jai,

Thanks for the patch.

On 15/03/23 14:33, Jai Luthra wrote:
> VCC_3V3_MAIN is the output of LM5141-Q1, and it serves as an input to
> TPS22965DSGT which produces VCC_3V3_SYS.
I would suggest to put link to schematics too :
Design docs: Link: https://www.ti.com/lit/zip/sprr459
> 
> Signed-off-by: Jai Luthra <j-luthra@ti.com>
With that change,
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>

Regards
Devarsh
> ---
>  arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 15 +++++++++++++--
>  1 file changed, 13 insertions(+), 2 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
> index 5c9012141ee2..063e69e45163 100644
> --- a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
> +++ b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
> @@ -76,10 +76,10 @@ vcc_5v0: regulator-1 {
>  		regulator-boot-on;
>  	};
>  
> -	vcc_3v3_sys: regulator-2 {
> +	vcc_3v3_main: regulator-2 {
>  		/* output of LM5141-Q1 */
>  		compatible = "regulator-fixed";
> -		regulator-name = "vcc_3v3_sys";
> +		regulator-name = "vcc_3v3_main";
>  		regulator-min-microvolt = <3300000>;
>  		regulator-max-microvolt = <3300000>;
>  		vin-supply = <&vmain_pd>;
> @@ -98,6 +98,17 @@ vdd_mmc1: regulator-3 {
>  		gpio = <&exp1 3 GPIO_ACTIVE_HIGH>;
>  	};
>  
> +	vcc_3v3_sys: regulator-4 {
> +		/* output of TPS222965DSGT */
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc_3v3_sys";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		vin-supply = <&vcc_3v3_main>;
> +		regulator-always-on;
> +		regulator-boot-on;
> +	};
> +
>  	leds {
>  		compatible = "gpio-leds";
>  		pinctrl-names = "default";
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel