Linux-ARM-Kernel Archive on lore.kernel.org
 help / color / Atom feed
* [PATCH] ARM: dts: at91: Reenable UART TX pull-ups
@ 2019-11-28 10:06 Ingo van Lil
  2019-12-03 13:04 ` Peter Rosin
  0 siblings, 1 reply; 4+ messages in thread
From: Ingo van Lil @ 2019-11-28 10:06 UTC (permalink / raw)
  To: linux-kernel, linux-arm-kernel, Peter Rosin
  Cc: Alexandre Belloni, Ludovic Desroches, Ingo van Lil

Pull-ups for SAM9 UART/USART TX lines were disabled in 5e04822f.
However, several chips in the SAM9 family require pull-ups to prevent
the TX lines from falling (and causing an endless break condition) when
the transceiver is disabled.

From the SAM9G20 datasheet, 32.5.1: "To prevent the TXD line from
falling when the USART is disabled, the use of an internal pull up
is mandatory.". This commit reenables the pull-ups for all chips having
that sentence in their datasheets.

Signed-off-by: Ingo van Lil <inguin@gmx.de>
---
 arch/arm/boot/dts/at91sam9260.dtsi | 12 ++++++------
 arch/arm/boot/dts/at91sam9261.dtsi |  6 +++---
 arch/arm/boot/dts/at91sam9263.dtsi |  6 +++---
 arch/arm/boot/dts/at91sam9g45.dtsi |  8 ++++----
 arch/arm/boot/dts/at91sam9rl.dtsi  |  8 ++++----
 5 files changed, 20 insertions(+), 20 deletions(-)

diff --git a/arch/arm/boot/dts/at91sam9260.dtsi b/arch/arm/boot/dts/at91sam9260.dtsi
index dee9c0c8a096..16c6fd3c4246 100644
--- a/arch/arm/boot/dts/at91sam9260.dtsi
+++ b/arch/arm/boot/dts/at91sam9260.dtsi
@@ -187,7 +187,7 @@
 				usart0 {
 					pinctrl_usart0: usart0-0 {
 						atmel,pins =
-							<AT91_PIOB 4 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOB 4 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOB 5 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};

@@ -221,7 +221,7 @@
 				usart1 {
 					pinctrl_usart1: usart1-0 {
 						atmel,pins =
-							<AT91_PIOB 6 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOB 6 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOB 7 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};

@@ -239,7 +239,7 @@
 				usart2 {
 					pinctrl_usart2: usart2-0 {
 						atmel,pins =
-							<AT91_PIOB 8 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOB 8 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOB 9 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};

@@ -257,7 +257,7 @@
 				usart3 {
 					pinctrl_usart3: usart3-0 {
 						atmel,pins =
-							<AT91_PIOB 10 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOB 10 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOB 11 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};

@@ -275,7 +275,7 @@
 				uart0 {
 					pinctrl_uart0: uart0-0 {
 						atmel,pins =
-							<AT91_PIOA 31 AT91_PERIPH_B AT91_PINCTRL_NONE
+							<AT91_PIOA 31 AT91_PERIPH_B AT91_PINCTRL_PULL_UP
 							 AT91_PIOA 30 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>;
 					};
 				};
@@ -283,7 +283,7 @@
 				uart1 {
 					pinctrl_uart1: uart1-0 {
 						atmel,pins =
-							<AT91_PIOB 12 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOB 12 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOB 13 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 				};
diff --git a/arch/arm/boot/dts/at91sam9261.dtsi b/arch/arm/boot/dts/at91sam9261.dtsi
index dba025a98527..5ed3d745ac86 100644
--- a/arch/arm/boot/dts/at91sam9261.dtsi
+++ b/arch/arm/boot/dts/at91sam9261.dtsi
@@ -329,7 +329,7 @@
 				usart0 {
 					pinctrl_usart0: usart0-0 {
 						atmel,pins =
-							<AT91_PIOC 8 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+							<AT91_PIOC 8 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
 							<AT91_PIOC 9 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};

@@ -347,7 +347,7 @@
 				usart1 {
 					pinctrl_usart1: usart1-0 {
 						atmel,pins =
-							<AT91_PIOC 12 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+							<AT91_PIOC 12 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
 							<AT91_PIOC 13 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};

@@ -365,7 +365,7 @@
 				usart2 {
 					pinctrl_usart2: usart2-0 {
 						atmel,pins =
-							<AT91_PIOC 14 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+							<AT91_PIOC 14 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
 							<AT91_PIOC 15 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};

diff --git a/arch/arm/boot/dts/at91sam9263.dtsi b/arch/arm/boot/dts/at91sam9263.dtsi
index 99678abdda93..5c990cfae254 100644
--- a/arch/arm/boot/dts/at91sam9263.dtsi
+++ b/arch/arm/boot/dts/at91sam9263.dtsi
@@ -183,7 +183,7 @@
 				usart0 {
 					pinctrl_usart0: usart0-0 {
 						atmel,pins =
-							<AT91_PIOA 26 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOA 26 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOA 27 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};

@@ -201,7 +201,7 @@
 				usart1 {
 					pinctrl_usart1: usart1-0 {
 						atmel,pins =
-							<AT91_PIOD 0 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOD 0 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOD 1 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};

@@ -219,7 +219,7 @@
 				usart2 {
 					pinctrl_usart2: usart2-0 {
 						atmel,pins =
-							<AT91_PIOD 2 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOD 2 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOD 3 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};

diff --git a/arch/arm/boot/dts/at91sam9g45.dtsi b/arch/arm/boot/dts/at91sam9g45.dtsi
index 691c95ea6175..fd179097a4bf 100644
--- a/arch/arm/boot/dts/at91sam9g45.dtsi
+++ b/arch/arm/boot/dts/at91sam9g45.dtsi
@@ -556,7 +556,7 @@
 				usart0 {
 					pinctrl_usart0: usart0-0 {
 						atmel,pins =
-							<AT91_PIOB 19 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOB 19 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOB 18 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};

@@ -574,7 +574,7 @@
 				usart1 {
 					pinctrl_usart1: usart1-0 {
 						atmel,pins =
-							<AT91_PIOB 4 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOB 4 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOB 5 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};

@@ -592,7 +592,7 @@
 				usart2 {
 					pinctrl_usart2: usart2-0 {
 						atmel,pins =
-							<AT91_PIOB 6 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOB 6 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOB 7 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};

@@ -610,7 +610,7 @@
 				usart3 {
 					pinctrl_usart3: usart3-0 {
 						atmel,pins =
-							<AT91_PIOB 8 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOB 8 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOB 9 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};

diff --git a/arch/arm/boot/dts/at91sam9rl.dtsi b/arch/arm/boot/dts/at91sam9rl.dtsi
index 8643b7151565..ea024e4b6e09 100644
--- a/arch/arm/boot/dts/at91sam9rl.dtsi
+++ b/arch/arm/boot/dts/at91sam9rl.dtsi
@@ -682,7 +682,7 @@
 				usart0 {
 					pinctrl_usart0: usart0-0 {
 						atmel,pins =
-							<AT91_PIOA 6 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+							<AT91_PIOA 6 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
 							<AT91_PIOA 7 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};

@@ -721,7 +721,7 @@
 				usart1 {
 					pinctrl_usart1: usart1-0 {
 						atmel,pins =
-							<AT91_PIOA 11 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+							<AT91_PIOA 11 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
 							<AT91_PIOA 12 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};

@@ -744,7 +744,7 @@
 				usart2 {
 					pinctrl_usart2: usart2-0 {
 						atmel,pins =
-							<AT91_PIOA 13 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+							<AT91_PIOA 13 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
 							<AT91_PIOA 14 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};

@@ -767,7 +767,7 @@
 				usart3 {
 					pinctrl_usart3: usart3-0 {
 						atmel,pins =
-							<AT91_PIOB 0 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+							<AT91_PIOB 0 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
 							<AT91_PIOB 1 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};

--
2.21.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 4+ messages in thread

* Re: [PATCH] ARM: dts: at91: Reenable UART TX pull-ups
  2019-11-28 10:06 [PATCH] ARM: dts: at91: Reenable UART TX pull-ups Ingo van Lil
@ 2019-12-03 13:04 ` Peter Rosin
  2019-12-03 13:22   ` Ingo van Lil
  0 siblings, 1 reply; 4+ messages in thread
From: Peter Rosin @ 2019-12-03 13:04 UTC (permalink / raw)
  To: Ingo van Lil, linux-kernel, linux-arm-kernel
  Cc: Alexandre Belloni, Ludovic Desroches

On 2019-11-28 11:06, Ingo van Lil wrote:
> Pull-ups for SAM9 UART/USART TX lines were disabled in 5e04822f.
> However, several chips in the SAM9 family require pull-ups to prevent
> the TX lines from falling (and causing an endless break condition) when
> the transceiver is disabled.
> 
> From the SAM9G20 datasheet, 32.5.1: "To prevent the TXD line from
> falling when the USART is disabled, the use of an internal pull up
> is mandatory.". This commit reenables the pull-ups for all chips having
> that sentence in their datasheets.
> 
> Signed-off-by: Ingo van Lil <inguin@gmx.de>

Sounds reasonable, and sorry for the breakage. However, perhaps a proper
fixes tag (with the prescribed length of the commit hash) should be in
there somewhere?

Fixes: 5e04822f7db5 ("ARM: dts: at91: fixes uart pinctrl, set pullup on rx, clear pullup on tx")

Also, I think the same kind of change was made to the barebox bootloader
at about the same time. Is there a fix for that queued up as well?

Cheers,
Peter
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 4+ messages in thread

* Re: [PATCH] ARM: dts: at91: Reenable UART TX pull-ups
  2019-12-03 13:04 ` Peter Rosin
@ 2019-12-03 13:22   ` Ingo van Lil
  0 siblings, 0 replies; 4+ messages in thread
From: Ingo van Lil @ 2019-12-03 13:22 UTC (permalink / raw)
  To: Peter Rosin, linux-kernel, linux-arm-kernel
  Cc: Alexandre Belloni, Ludovic Desroches

On 12/3/19 2:04 PM, Peter Rosin wrote:

> Sounds reasonable, and sorry for the breakage. However, perhaps a proper
> fixes tag (with the prescribed length of the commit hash) should be in
> there somewhere?

Sounds good, I will add one.


> Also, I think the same kind of change was made to the barebox bootloader
> at about the same time. Is there a fix for that queued up as well?

Sorry, I'm not familiar with Barebox. We use u-boot.

Regards,
Ingo

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 4+ messages in thread

* [PATCH] ARM: dts: at91: Reenable UART TX pull-ups
@ 2019-12-03 14:21 Ingo van Lil
  0 siblings, 0 replies; 4+ messages in thread
From: Ingo van Lil @ 2019-12-03 14:21 UTC (permalink / raw)
  To: linux-kernel, linux-arm-kernel, Peter Rosin
  Cc: Alexandre Belloni, Ludovic Desroches, Ingo van Lil

Pull-ups for SAM9 UART/USART TX lines were disabled in a previous
commit. However, several chips in the SAM9 family require pull-ups to
prevent the TX lines from falling (and causing an endless break
condition) when the transceiver is disabled.

From the SAM9G20 datasheet, 32.5.1: "To prevent the TXD line from
falling when the USART is disabled, the use of an internal pull up
is mandatory.". This commit reenables the pull-ups for all chips having
that sentence in their datasheets.

Fixes: 5e04822f7db5 ("ARM: dts: at91: fixes uart pinctrl, set pullup on rx, clear pullup on tx")
Signed-off-by: Ingo van Lil <inguin@gmx.de>
Cc: Peter Rosin <peda@axentia.se>
---
 arch/arm/boot/dts/at91sam9260.dtsi | 12 ++++++------
 arch/arm/boot/dts/at91sam9261.dtsi |  6 +++---
 arch/arm/boot/dts/at91sam9263.dtsi |  6 +++---
 arch/arm/boot/dts/at91sam9g45.dtsi |  8 ++++----
 arch/arm/boot/dts/at91sam9rl.dtsi  |  8 ++++----
 5 files changed, 20 insertions(+), 20 deletions(-)

diff --git a/arch/arm/boot/dts/at91sam9260.dtsi b/arch/arm/boot/dts/at91sam9260.dtsi
index dee9c0c8a096..16c6fd3c4246 100644
--- a/arch/arm/boot/dts/at91sam9260.dtsi
+++ b/arch/arm/boot/dts/at91sam9260.dtsi
@@ -187,7 +187,7 @@
 				usart0 {
 					pinctrl_usart0: usart0-0 {
 						atmel,pins =
-							<AT91_PIOB 4 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOB 4 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOB 5 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};

@@ -221,7 +221,7 @@
 				usart1 {
 					pinctrl_usart1: usart1-0 {
 						atmel,pins =
-							<AT91_PIOB 6 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOB 6 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOB 7 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};

@@ -239,7 +239,7 @@
 				usart2 {
 					pinctrl_usart2: usart2-0 {
 						atmel,pins =
-							<AT91_PIOB 8 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOB 8 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOB 9 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};

@@ -257,7 +257,7 @@
 				usart3 {
 					pinctrl_usart3: usart3-0 {
 						atmel,pins =
-							<AT91_PIOB 10 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOB 10 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOB 11 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};

@@ -275,7 +275,7 @@
 				uart0 {
 					pinctrl_uart0: uart0-0 {
 						atmel,pins =
-							<AT91_PIOA 31 AT91_PERIPH_B AT91_PINCTRL_NONE
+							<AT91_PIOA 31 AT91_PERIPH_B AT91_PINCTRL_PULL_UP
 							 AT91_PIOA 30 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>;
 					};
 				};
@@ -283,7 +283,7 @@
 				uart1 {
 					pinctrl_uart1: uart1-0 {
 						atmel,pins =
-							<AT91_PIOB 12 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOB 12 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOB 13 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 				};
diff --git a/arch/arm/boot/dts/at91sam9261.dtsi b/arch/arm/boot/dts/at91sam9261.dtsi
index dba025a98527..5ed3d745ac86 100644
--- a/arch/arm/boot/dts/at91sam9261.dtsi
+++ b/arch/arm/boot/dts/at91sam9261.dtsi
@@ -329,7 +329,7 @@
 				usart0 {
 					pinctrl_usart0: usart0-0 {
 						atmel,pins =
-							<AT91_PIOC 8 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+							<AT91_PIOC 8 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
 							<AT91_PIOC 9 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};

@@ -347,7 +347,7 @@
 				usart1 {
 					pinctrl_usart1: usart1-0 {
 						atmel,pins =
-							<AT91_PIOC 12 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+							<AT91_PIOC 12 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
 							<AT91_PIOC 13 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};

@@ -365,7 +365,7 @@
 				usart2 {
 					pinctrl_usart2: usart2-0 {
 						atmel,pins =
-							<AT91_PIOC 14 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+							<AT91_PIOC 14 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
 							<AT91_PIOC 15 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};

diff --git a/arch/arm/boot/dts/at91sam9263.dtsi b/arch/arm/boot/dts/at91sam9263.dtsi
index 99678abdda93..5c990cfae254 100644
--- a/arch/arm/boot/dts/at91sam9263.dtsi
+++ b/arch/arm/boot/dts/at91sam9263.dtsi
@@ -183,7 +183,7 @@
 				usart0 {
 					pinctrl_usart0: usart0-0 {
 						atmel,pins =
-							<AT91_PIOA 26 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOA 26 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOA 27 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};

@@ -201,7 +201,7 @@
 				usart1 {
 					pinctrl_usart1: usart1-0 {
 						atmel,pins =
-							<AT91_PIOD 0 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOD 0 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOD 1 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};

@@ -219,7 +219,7 @@
 				usart2 {
 					pinctrl_usart2: usart2-0 {
 						atmel,pins =
-							<AT91_PIOD 2 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOD 2 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOD 3 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};

diff --git a/arch/arm/boot/dts/at91sam9g45.dtsi b/arch/arm/boot/dts/at91sam9g45.dtsi
index 691c95ea6175..fd179097a4bf 100644
--- a/arch/arm/boot/dts/at91sam9g45.dtsi
+++ b/arch/arm/boot/dts/at91sam9g45.dtsi
@@ -556,7 +556,7 @@
 				usart0 {
 					pinctrl_usart0: usart0-0 {
 						atmel,pins =
-							<AT91_PIOB 19 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOB 19 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOB 18 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};

@@ -574,7 +574,7 @@
 				usart1 {
 					pinctrl_usart1: usart1-0 {
 						atmel,pins =
-							<AT91_PIOB 4 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOB 4 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOB 5 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};

@@ -592,7 +592,7 @@
 				usart2 {
 					pinctrl_usart2: usart2-0 {
 						atmel,pins =
-							<AT91_PIOB 6 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOB 6 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOB 7 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};

@@ -610,7 +610,7 @@
 				usart3 {
 					pinctrl_usart3: usart3-0 {
 						atmel,pins =
-							<AT91_PIOB 8 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOB 8 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOB 9 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};

diff --git a/arch/arm/boot/dts/at91sam9rl.dtsi b/arch/arm/boot/dts/at91sam9rl.dtsi
index 8643b7151565..ea024e4b6e09 100644
--- a/arch/arm/boot/dts/at91sam9rl.dtsi
+++ b/arch/arm/boot/dts/at91sam9rl.dtsi
@@ -682,7 +682,7 @@
 				usart0 {
 					pinctrl_usart0: usart0-0 {
 						atmel,pins =
-							<AT91_PIOA 6 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+							<AT91_PIOA 6 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
 							<AT91_PIOA 7 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};

@@ -721,7 +721,7 @@
 				usart1 {
 					pinctrl_usart1: usart1-0 {
 						atmel,pins =
-							<AT91_PIOA 11 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+							<AT91_PIOA 11 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
 							<AT91_PIOA 12 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};

@@ -744,7 +744,7 @@
 				usart2 {
 					pinctrl_usart2: usart2-0 {
 						atmel,pins =
-							<AT91_PIOA 13 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+							<AT91_PIOA 13 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
 							<AT91_PIOA 14 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};

@@ -767,7 +767,7 @@
 				usart3 {
 					pinctrl_usart3: usart3-0 {
 						atmel,pins =
-							<AT91_PIOB 0 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+							<AT91_PIOB 0 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
 							<AT91_PIOB 1 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};

--
2.21.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 4+ messages in thread

end of thread, back to index

Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-11-28 10:06 [PATCH] ARM: dts: at91: Reenable UART TX pull-ups Ingo van Lil
2019-12-03 13:04 ` Peter Rosin
2019-12-03 13:22   ` Ingo van Lil
2019-12-03 14:21 Ingo van Lil

Linux-ARM-Kernel Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-arm-kernel/0 linux-arm-kernel/git/0.git
	git clone --mirror https://lore.kernel.org/linux-arm-kernel/1 linux-arm-kernel/git/1.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-arm-kernel linux-arm-kernel/ https://lore.kernel.org/linux-arm-kernel \
		linux-arm-kernel@lists.infradead.org
	public-inbox-index linux-arm-kernel

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.infradead.lists.linux-arm-kernel


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git