Re: [PATCH v2 net-next 2/2] net: macb: Add zynqmp SGMII dynamic configuration support

[<Claudiu.Beznea@microchip.com>]

On 29.07.2022 22:35, Radhey Shyam Pandey wrote:
> EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
> 
> Add support for the dynamic configuration which takes care of configuring
> the GEM secure space configuration registers using EEMI APIs. High level
> sequence is to:
> - Check for the PM dynamic configuration support, if no error proceed with
>   GEM dynamic configurations(next steps) otherwise skip the dynamic
>   configuration.
> - Configure GEM Fixed configurations.
> - Configure GEM_CLK_CTRL (gemX_sgmii_mode).
> - Trigger GEM reset.
> 
> Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
> Reviewed-by: Andrew Lunn <andrew@lunn.ch>
> Tested-by: Conor Dooley <conor.dooley@microchip.com> (for MPFS)
> ---
> Changes for v2:
> - Add phy_exit() in error return paths.
> ---
>  drivers/net/ethernet/cadence/macb_main.c | 25 +++++++++++++++++++++++++
>  1 file changed, 25 insertions(+)
> 
> diff --git a/drivers/net/ethernet/cadence/macb_main.c b/drivers/net/ethernet/cadence/macb_main.c
> index 4cd4f57ca2aa..517b40ff098b 100644
> --- a/drivers/net/ethernet/cadence/macb_main.c
> +++ b/drivers/net/ethernet/cadence/macb_main.c
> @@ -38,6 +38,7 @@
>  #include <linux/pm_runtime.h>
>  #include <linux/ptp_classify.h>
>  #include <linux/reset.h>
> +#include <linux/firmware/xlnx-zynqmp.h>
>  #include "macb.h"
> 
>  /* This structure is only used for MACB on SiFive FU540 devices */
> @@ -4621,6 +4622,30 @@ static int init_reset_optional(struct platform_device *pdev)
>                                              "failed to init SGMII PHY\n");
>         }
> 
> +       ret = zynqmp_pm_is_function_supported(PM_IOCTL, IOCTL_SET_GEM_CONFIG);
> +       if (!ret) {
> +               u32 pm_info[2];
> +
> +               ret = of_property_read_u32_array(pdev->dev.of_node, "power-domains",
> +                                                pm_info, ARRAY_SIZE(pm_info));
> +               if (ret < 0) {
> +                       phy_exit(bp->sgmii_phy);

Could you move this to a single exit point and jump in there with goto?
Same for the rest of occurencies.

Also, I notice just now that phy_init() is done only if bp->phy_interface
== PHY_INTERFACE_MODE_SGMII, phy_exit() should be handled only if this is
true, too.

> +                       dev_err(&pdev->dev, "Failed to read power management information\n");
> +                       return ret;
> +               }
> +               ret = zynqmp_pm_set_gem_config(pm_info[1], GEM_CONFIG_FIXED, 0);
> +               if (ret < 0) {
> +                       phy_exit(bp->sgmii_phy);
> +                       return ret;
> +               }
> +
> +               ret = zynqmp_pm_set_gem_config(pm_info[1], GEM_CONFIG_SGMII_MODE, 1);
> +               if (ret < 0) {
> +                       phy_exit(bp->sgmii_phy);
> +                       return ret;
> +               }
> +       }
> +
>         /* Fully reset controller at hardware level if mapped in device tree */
>         ret = device_reset_optional(&pdev->dev);
>         if (ret) {
> --
> 2.1.1
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel