[parent not found: <1435355419-23602-1-git-send-email-bjorn.andersson-/MT0OVThwyLZJqsBc5GL+g@public.gmane.org>]
* [PATCH v2 01/11] soc: qcom: Add device tree binding for SMEM
[not found] ` <1435355419-23602-1-git-send-email-bjorn.andersson-/MT0OVThwyLZJqsBc5GL+g@public.gmane.org>
@ 2015-06-26 21:50 ` bjorn-UYDU3/A3LUY
2015-07-08 23:56 ` Stephen Boyd
2015-07-23 20:49 ` Andy Gross
0 siblings, 2 replies; 39+ messages in thread
From: bjorn-UYDU3/A3LUY @ 2015-06-26 21:50 UTC (permalink / raw)
To: Andy Gross, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell,
Kumar Gala
Cc: Jeffrey Hugo, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-arm-msm-u79uwXL29TY76Z2rM5mHXA
From: Bjorn Andersson <bjorn.andersson-/MT0OVThwyLZJqsBc5GL+g@public.gmane.org>
Add device tree binding documentation for the Qualcom Shared Memory
Manager.
Signed-off-by: Bjorn Andersson <bjorn.andersson-/MT0OVThwyLZJqsBc5GL+g@public.gmane.org>
---
.../devicetree/bindings/soc/qcom/qcom,smem.txt | 51 ++++++++++++++++++++++
1 file changed, 51 insertions(+)
create mode 100644 Documentation/devicetree/bindings/soc/qcom/qcom,smem.txt
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smem.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,smem.txt
new file mode 100644
index 0000000..19cad6c
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smem.txt
@@ -0,0 +1,51 @@
+Qualcomm Shared Memory Manager binding
+
+This binding describes the Qualcomm Shared Memory Manager, used to share data
+between various subsystems and OSes in Qualcomm platforms.
+
+- compatible:
+ Usage: required
+ Value type: <stringlist>
+ Definition: must be:
+ "qcom,smem"
+
+- memory-region:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: handle to memory reservation for main SMEM memory region.
+
+- reg:
+ Usage: optional
+ Value type: <prop-encoded-array>
+ Definition: base address and size pair for any additional memory areas
+ of the shared memory.
+
+- hwlocks:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: reference to a hwspinlock used to protect allocations from
+ the shared memory
+
+= EXAMPLE
+The following example shows the SMEM setup for MSM8974, with a main SMEM region
+at 0xfa00000 and an auxiliary region at 0xfc428000:
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ smem_region: smem@fa00000 {
+ reg = <0xfa00000 0x200000>;
+ no-map;
+ };
+ };
+
+ smem@fa00000 {
+ compatible = "qcom,smem";
+
+ memory-region = <&smem_region>;
+ reg = <0xfc428000 0x4000>;
+
+ hwlocks = <&tcsr_mutex 3>;
+ };
--
1.9.3 (Apple Git-50)
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 39+ messages in thread* Re: [PATCH v2 01/11] soc: qcom: Add device tree binding for SMEM
2015-06-26 21:50 ` [PATCH v2 01/11] soc: qcom: Add device tree binding for SMEM bjorn-UYDU3/A3LUY
@ 2015-07-08 23:56 ` Stephen Boyd
2015-07-09 3:50 ` Andy Gross
[not found] ` <559DB8B2.2090202-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2015-07-23 20:49 ` Andy Gross
1 sibling, 2 replies; 39+ messages in thread
From: Stephen Boyd @ 2015-07-08 23:56 UTC (permalink / raw)
To: bjorn, Andy Gross, Rob Herring, Pawel Moll, Mark Rutland,
Ian Campbell, Kumar Gala
Cc: Jeffrey Hugo, devicetree, linux-kernel, linux-arm-msm
On 06/26/2015 02:50 PM, bjorn@kryo.se wrote:
> += EXAMPLE
> +The following example shows the SMEM setup for MSM8974, with a main SMEM region
> +at 0xfa00000 and an auxiliary region at 0xfc428000:
> +
> + reserved-memory {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + smem_region: smem@fa00000 {
> + reg = <0xfa00000 0x200000>;
> + no-map;
> + };
> + };
> +
> + smem@fa00000 {
This should be smem@fc428000 matching the first reg property. It's weird
though, because if smem is using a secondary region it will be under the
SoC node and have a reg property. Otherwise it would be directly under
the root node and only have a memory-region. It would be nice if we
could somehow move the rpm message ram (0xfc428000) into the
reserved-memory node so that we could use memory-region for both regions.
> + compatible = "qcom,smem";
> +
> + memory-region = <&smem_region>;
> + reg = <0xfc428000 0x4000>;
> +
> + hwlocks = <&tcsr_mutex 3>;
> + };
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply [flat|nested] 39+ messages in thread* Re: [PATCH v2 01/11] soc: qcom: Add device tree binding for SMEM
2015-07-08 23:56 ` Stephen Boyd
@ 2015-07-09 3:50 ` Andy Gross
[not found] ` <559DB8B2.2090202-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
1 sibling, 0 replies; 39+ messages in thread
From: Andy Gross @ 2015-07-09 3:50 UTC (permalink / raw)
To: Stephen Boyd
Cc: bjorn, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell,
Kumar Gala, Jeffrey Hugo, devicetree, linux-kernel,
linux-arm-msm
On Wed, Jul 08, 2015 at 04:56:34PM -0700, Stephen Boyd wrote:
> On 06/26/2015 02:50 PM, bjorn@kryo.se wrote:
> > += EXAMPLE
> > +The following example shows the SMEM setup for MSM8974, with a main SMEM region
> > +at 0xfa00000 and an auxiliary region at 0xfc428000:
> > +
> > + reserved-memory {
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + ranges;
> > +
> > + smem_region: smem@fa00000 {
> > + reg = <0xfa00000 0x200000>;
> > + no-map;
> > + };
> > + };
> > +
> > + smem@fa00000 {
>
> This should be smem@fc428000 matching the first reg property. It's weird
> though, because if smem is using a secondary region it will be under the
> SoC node and have a reg property. Otherwise it would be directly under
> the root node and only have a memory-region. It would be nice if we
> could somehow move the rpm message ram (0xfc428000) into the
> reserved-memory node so that we could use memory-region for both regions.
The memory-region is just used to describe 'real' memory. The RPM message is IO
memory and part of the SOC. Thats my take at least.
>
> > + compatible = "qcom,smem";
> > +
> > + memory-region = <&smem_region>;
> > + reg = <0xfc428000 0x4000>;
> > +
> > + hwlocks = <&tcsr_mutex 3>;
> > + };
--
Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply [flat|nested] 39+ messages in thread[parent not found: <559DB8B2.2090202-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>]
* Re: [PATCH v2 01/11] soc: qcom: Add device tree binding for SMEM
[not found] ` <559DB8B2.2090202-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
@ 2015-07-13 22:30 ` Bjorn Andersson
0 siblings, 0 replies; 39+ messages in thread
From: Bjorn Andersson @ 2015-07-13 22:30 UTC (permalink / raw)
To: Stephen Boyd
Cc: bjorn-UYDU3/A3LUY, Andy Gross, Rob Herring, Pawel Moll,
Mark Rutland, Ian Campbell, Kumar Gala, Jeffrey Hugo,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-arm-msm-u79uwXL29TY76Z2rM5mHXA
On Wed 08 Jul 16:56 PDT 2015, Stephen Boyd wrote:
> On 06/26/2015 02:50 PM, bjorn-UYDU3/A3LUY@public.gmane.org wrote:
> > += EXAMPLE
> > +The following example shows the SMEM setup for MSM8974, with a main SMEM region
> > +at 0xfa00000 and an auxiliary region at 0xfc428000:
> > +
> > + reserved-memory {
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + ranges;
> > +
> > + smem_region: smem@fa00000 {
> > + reg = <0xfa00000 0x200000>;
> > + no-map;
> > + };
> > + };
> > +
> > + smem@fa00000 {
>
> This should be smem@fc428000 matching the first reg property. It's weird
> though, because if smem is using a secondary region it will be under the
> SoC node and have a reg property. Otherwise it would be directly under
> the root node and only have a memory-region. It would be nice if we
> could somehow move the rpm message ram (0xfc428000) into the
> reserved-memory node so that we could use memory-region for both regions.
>
I agree, the semantics here became a little bit odd.
I do not think we should list the 0xfc428000 region as a memory-region,
as it's "device memory" and I do like the fact that we don't repeat
ourselves with listing the memory-region as a reg.
Therefor I think this is the least ugly option, but the address in the
name of the node should be updated.
> > + compatible = "qcom,smem";
> > +
> > + memory-region = <&smem_region>;
> > + reg = <0xfc428000 0x4000>;
> > +
> > + hwlocks = <&tcsr_mutex 3>;
> > + };
>
Thanks,
Bjorn
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 39+ messages in thread
* Re: [PATCH v2 01/11] soc: qcom: Add device tree binding for SMEM
2015-06-26 21:50 ` [PATCH v2 01/11] soc: qcom: Add device tree binding for SMEM bjorn-UYDU3/A3LUY
2015-07-08 23:56 ` Stephen Boyd
@ 2015-07-23 20:49 ` Andy Gross
1 sibling, 0 replies; 39+ messages in thread
From: Andy Gross @ 2015-07-23 20:49 UTC (permalink / raw)
To: bjorn
Cc: Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
Jeffrey Hugo, devicetree, linux-kernel, linux-arm-msm
On Fri, Jun 26, 2015 at 02:50:09PM -0700, bjorn@kryo.se wrote:
> From: Bjorn Andersson <bjorn.andersson@sonymobile.com>
>
> Add device tree binding documentation for the Qualcom Shared Memory
> Manager.
>
> Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
<snip>
> + smem@fa00000 {
> + compatible = "qcom,smem";
> +
> + memory-region = <&smem_region>;
> + reg = <0xfc428000 0x4000>;
I'll fixup the address here before applying.
Applied, thanks!
--
Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply [flat|nested] 39+ messages in thread
* [PATCH v2 02/11] soc: qcom: Add Shared Memory Manager driver
2015-06-26 21:50 [PATCH v2 00/11] Qualcomm Shared Memory & RPM drivers bjorn
[not found] ` <1435355419-23602-1-git-send-email-bjorn.andersson-/MT0OVThwyLZJqsBc5GL+g@public.gmane.org>
@ 2015-06-26 21:50 ` bjorn
2015-07-17 21:15 ` Andy Gross
2015-07-23 20:47 ` Andy Gross
2015-06-26 21:50 ` [PATCH v2 03/11] soc: qcom: Add device tree binding for Shared Memory Device bjorn
` (8 subsequent siblings)
10 siblings, 2 replies; 39+ messages in thread
From: bjorn @ 2015-06-26 21:50 UTC (permalink / raw)
To: Kumar Gala, Andy Gross
Cc: Jeffrey Hugo, linux-kernel, linux-arm-msm, linux-soc
From: Bjorn Andersson <bjorn.andersson@sonymobile.com>
The Shared Memory Manager driver implements an interface for allocating
and accessing items in the memory area shared among all of the
processors in a Qualcomm platform.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
---
drivers/soc/qcom/Kconfig | 8 +
drivers/soc/qcom/Makefile | 1 +
drivers/soc/qcom/smem.c | 775 ++++++++++++++++++++++++++++++++++++++++++
include/linux/soc/qcom/smem.h | 11 +
4 files changed, 795 insertions(+)
create mode 100644 drivers/soc/qcom/smem.c
create mode 100644 include/linux/soc/qcom/smem.h
diff --git a/drivers/soc/qcom/Kconfig b/drivers/soc/qcom/Kconfig
index 01aa2fd..0e115c0 100644
--- a/drivers/soc/qcom/Kconfig
+++ b/drivers/soc/qcom/Kconfig
@@ -19,3 +19,11 @@ config QCOM_PM
QCOM Platform specific power driver to manage cores and L2 low power
modes. It interface with various system drivers to put the cores in
low power modes.
+
+config QCOM_SMEM
+ tristate "Qualcomm Shared Memory Manager (SMEM)"
+ depends on ARCH_QCOM
+ help
+ Say y here to enable support for the Qualcomm Shared Memory Manager.
+ The driver provides an interface to items in a heap shared among all
+ processors in a Qualcomm platform.
diff --git a/drivers/soc/qcom/Makefile b/drivers/soc/qcom/Makefile
index 931d385..3a033c4 100644
--- a/drivers/soc/qcom/Makefile
+++ b/drivers/soc/qcom/Makefile
@@ -1,2 +1,3 @@
obj-$(CONFIG_QCOM_GSBI) += qcom_gsbi.o
obj-$(CONFIG_QCOM_PM) += spm.o
+obj-$(CONFIG_QCOM_SMEM) += smem.o
diff --git a/drivers/soc/qcom/smem.c b/drivers/soc/qcom/smem.c
new file mode 100644
index 0000000..7c2c324c
--- /dev/null
+++ b/drivers/soc/qcom/smem.c
@@ -0,0 +1,775 @@
+/*
+ * Copyright (c) 2015, Sony Mobile Communications AB.
+ * Copyright (c) 2012-2013, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/hwspinlock.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/soc/qcom/smem.h>
+
+/*
+ * The Qualcomm shared memory system is a allocate only heap structure that
+ * consists of one of more memory areas that can be accessed by the processors
+ * in the SoC.
+ *
+ * All systems contains a global heap, accessible by all processors in the SoC,
+ * with a table of contents data structure (@smem_header) at the beginning of
+ * the main shared memory block.
+ *
+ * The global header contains meta data for allocations as well as a fixed list
+ * of 512 entries (@smem_global_entry) that can be initialized to reference
+ * parts of the shared memory space.
+ *
+ *
+ * In addition to this global heap a set of "private" heaps can be set up at
+ * boot time with access restrictions so that only certain processor pairs can
+ * access the data.
+ *
+ * These partitions are referenced from an optional partition table
+ * (@smem_ptable), that is found 4kB from the end of the main smem region. The
+ * partition table entries (@smem_ptable_entry) lists the involved processors
+ * (or hosts) and their location in the main shared memory region.
+ *
+ * Each partition starts with a header (@smem_partition_header) that identifies
+ * the partition and holds properties for the two internal memory regions. The
+ * two regions are cached and non-cached memory respectively. Each region
+ * contain a link list of allocation headers (@smem_private_entry) followed by
+ * their data.
+ *
+ * Items in the non-cached region are allocated from the start of the partition
+ * while items in the cached region are allocated from the end. The free area
+ * is hence the region between the cached and non-cached offsets.
+ *
+ *
+ * To synchronize allocations in the shared memory heaps a remote spinlock must
+ * be held - currently lock number 3 of the sfpb or tcsr is used for this on all
+ * platforms.
+ *
+ */
+
+/*
+ * Item 3 of the global heap contains an array of versions for the various
+ * software components in the SoC. We verify that the boot loader version is
+ * what the expected version (SMEM_EXPECTED_VERSION) as a sanity check.
+ */
+#define SMEM_ITEM_VERSION 3
+#define SMEM_MASTER_SBL_VERSION_INDEX 7
+#define SMEM_EXPECTED_VERSION 11
+
+/*
+ * The first 8 items are only to be allocated by the boot loader while
+ * initializing the heap.
+ */
+#define SMEM_ITEM_LAST_FIXED 8
+
+/* Highest accepted item number, for both global and private heaps */
+#define SMEM_ITEM_COUNT 512
+
+/* Processor/host identifier for the application processor */
+#define SMEM_HOST_APPS 0
+
+/* Max number of processors/hosts in a system */
+#define SMEM_HOST_COUNT 9
+
+/**
+ * struct smem_proc_comm - proc_comm communication struct (legacy)
+ * @command: current command to be executed
+ * @status: status of the currently requested command
+ * @params: parameters to the command
+ */
+struct smem_proc_comm {
+ u32 command;
+ u32 status;
+ u32 params[2];
+};
+
+/**
+ * struct smem_global_entry - entry to reference smem items on the heap
+ * @allocated: boolean to indicate if this entry is used
+ * @offset: offset to the allocated space
+ * @size: size of the allocated space, 8 byte aligned
+ * @aux_base: base address for the memory region used by this unit, or 0 for
+ * the default region. bits 0,1 are reserved
+ */
+struct smem_global_entry {
+ u32 allocated;
+ u32 offset;
+ u32 size;
+ u32 aux_base; /* bits 1:0 reserved */
+};
+#define AUX_BASE_MASK 0xfffffffc
+
+/**
+ * struct smem_header - header found in beginning of primary smem region
+ * @proc_comm: proc_comm communication interface (legacy)
+ * @version: array of versions for the various subsystems
+ * @initialized: boolean to indicate that smem is initialized
+ * @free_offset: index of the first unallocated byte in smem
+ * @available: number of bytes available for allocation
+ * @reserved: reserved field, must be 0
+ * toc: array of references to items
+ */
+struct smem_header {
+ struct smem_proc_comm proc_comm[4];
+ u32 version[32];
+ u32 initialized;
+ u32 free_offset;
+ u32 available;
+ u32 reserved;
+ struct smem_global_entry toc[SMEM_ITEM_COUNT];
+};
+
+/**
+ * struct smem_ptable_entry - one entry in the @smem_ptable list
+ * @offset: offset, within the main shared memory region, of the partition
+ * @size: size of the partition
+ * @flags: flags for the partition (currently unused)
+ * @host0: first processor/host with access to this partition
+ * @host1: second processor/host with access to this partition
+ * @reserved: reserved entries for later use
+ */
+struct smem_ptable_entry {
+ u32 offset;
+ u32 size;
+ u32 flags;
+ u16 host0;
+ u16 host1;
+ u32 reserved[8];
+};
+
+/**
+ * struct smem_ptable - partition table for the private partitions
+ * @magic: magic number, must be SMEM_PTABLE_MAGIC
+ * @version: version of the partition table
+ * @num_entries: number of partitions in the table
+ * @reserved: for now reserved entries
+ * @entry: list of @smem_ptable_entry for the @num_entries partitions
+ */
+struct smem_ptable {
+ u32 magic;
+ u32 version;
+ u32 num_entries;
+ u32 reserved[5];
+ struct smem_ptable_entry entry[];
+};
+#define SMEM_PTABLE_MAGIC 0x434f5424 /* "$TOC" */
+
+/**
+ * struct smem_partition_header - header of the partitions
+ * @magic: magic number, must be SMEM_PART_MAGIC
+ * @host0: first processor/host with access to this partition
+ * @host1: second processor/host with access to this partition
+ * @size: size of the partition
+ * @offset_free_uncached: offset to the first free byte of uncached memory in
+ * this partition
+ * @offset_free_cached: offset to the first free byte of cached memory in this
+ * partition
+ * @reserved: for now reserved entries
+ */
+struct smem_partition_header {
+ u32 magic;
+ u16 host0;
+ u16 host1;
+ u32 size;
+ u32 offset_free_uncached;
+ u32 offset_free_cached;
+ u32 reserved[3];
+};
+#define SMEM_PART_MAGIC 0x54525024 /* "$PRT" */
+
+/**
+ * struct smem_private_entry - header of each item in the private partition
+ * @canary: magic number, must be SMEM_PRIVATE_CANARY
+ * @item: identifying number of the smem item
+ * @size: size of the data, including padding bytes
+ * @padding_data: number of bytes of padding of data
+ * @padding_hdr: number of bytes of padding between the header and the data
+ * @reserved: for now reserved entry
+ */
+struct smem_private_entry {
+ u16 canary;
+ u16 item;
+ u32 size; /* includes padding bytes */
+ u16 padding_data;
+ u16 padding_hdr;
+ u32 reserved;
+};
+#define SMEM_PRIVATE_CANARY 0xa5a5
+
+/**
+ * struct smem_region - representation of a chunk of memory used for smem
+ * @aux_base: identifier of aux_mem base
+ * @virt_base: virtual base address of memory with this aux_mem identifier
+ * @size: size of the memory region
+ */
+struct smem_region {
+ u32 aux_base;
+ void __iomem *virt_base;
+ size_t size;
+};
+
+/**
+ * struct qcom_smem - device data for the smem device
+ * @dev: device pointer
+ * @hwlock: reference to a hwspinlock
+ * @partitions: list of pointers to partitions affecting the current
+ * processor/host
+ * @num_regions: number of @regions
+ * @regions: list of the memory regions defining the shared memory
+ */
+struct qcom_smem {
+ struct device *dev;
+
+ struct hwspinlock *hwlock;
+
+ struct smem_partition_header *partitions[SMEM_HOST_COUNT];
+
+ unsigned num_regions;
+ struct smem_region regions[0];
+};
+
+/* Pointer to the one and only smem handle */
+static struct qcom_smem *__smem;
+
+/* Timeout (ms) for the trylock of remote spinlocks */
+#define HWSPINLOCK_TIMEOUT 1000
+
+static int qcom_smem_alloc_private(struct qcom_smem *smem,
+ unsigned host,
+ unsigned item,
+ size_t size)
+{
+ struct smem_partition_header *phdr;
+ struct smem_private_entry *hdr;
+ size_t alloc_size;
+ void *p;
+
+ /* We're not going to find it if there's no matching partition */
+ if (host >= SMEM_HOST_COUNT || !smem->partitions[host])
+ return -ENOENT;
+
+ phdr = smem->partitions[host];
+
+ p = (void *)phdr + sizeof(*phdr);
+ while (p < (void *)phdr + phdr->offset_free_uncached) {
+ hdr = p;
+
+ if (hdr->canary != SMEM_PRIVATE_CANARY) {
+ dev_err(smem->dev,
+ "Found invalid canary in host %d partition\n",
+ host);
+ return -EINVAL;
+ }
+
+ if (hdr->item == item)
+ return -EEXIST;
+
+ p += sizeof(*hdr) + hdr->padding_hdr + hdr->size;
+ }
+
+ /* Check that we don't grow into the cached region */
+ alloc_size = sizeof(*hdr) + ALIGN(size, 8);
+ if (p + alloc_size >= (void *)phdr + phdr->offset_free_cached) {
+ dev_err(smem->dev, "Out of memory\n");
+ return -ENOSPC;
+ }
+
+ hdr = p;
+ hdr->canary = SMEM_PRIVATE_CANARY;
+ hdr->item = item;
+ hdr->size = ALIGN(size, 8);
+ hdr->padding_data = hdr->size - size;
+ hdr->padding_hdr = 0;
+
+ /*
+ * Ensure the header is written before we advance the free offset, so
+ * that remote processors that does not take the remote spinlock still
+ * gets a consistent view of the linked list.
+ */
+ wmb();
+ phdr->offset_free_uncached += alloc_size;
+
+ return 0;
+}
+
+static int qcom_smem_alloc_global(struct qcom_smem *smem,
+ unsigned item,
+ size_t size)
+{
+ struct smem_header *header;
+ struct smem_global_entry *entry;
+
+ if (WARN_ON(item >= SMEM_ITEM_COUNT))
+ return -EINVAL;
+
+ header = smem->regions[0].virt_base;
+ entry = &header->toc[item];
+ if (entry->allocated)
+ return -EEXIST;
+
+ size = ALIGN(size, 8);
+ if (WARN_ON(size > header->available))
+ return -ENOMEM;
+
+ entry->offset = header->free_offset;
+ entry->size = size;
+
+ /*
+ * Ensure the header is consistent before we mark the item allocated,
+ * so that remote processors will get a consistent view of the item
+ * even though they do not take the spinlock on read.
+ */
+ wmb();
+ entry->allocated = 1;
+
+ header->free_offset += size;
+ header->available -= size;
+
+ return 0;
+}
+
+/**
+ * qcom_smem_alloc() - allocate space for a smem item
+ * @host: remote processor id, or -1
+ * @item: smem item handle
+ * @size: number of bytes to be allocated
+ *
+ * Allocate space for a given smem item of size @size, given that the item is
+ * not yet allocated.
+ */
+int qcom_smem_alloc(unsigned host, unsigned item, size_t size)
+{
+ unsigned long flags;
+ int ret;
+
+ if (!__smem)
+ return -EPROBE_DEFER;
+
+ if (item < SMEM_ITEM_LAST_FIXED) {
+ dev_err(__smem->dev,
+ "Rejecting allocation of static entry %d\n", item);
+ return -EINVAL;
+ }
+
+ ret = hwspin_lock_timeout_irqsave(__smem->hwlock,
+ HWSPINLOCK_TIMEOUT,
+ &flags);
+ if (ret)
+ return ret;
+
+ ret = qcom_smem_alloc_private(__smem, host, item, size);
+ if (ret == -ENOENT)
+ ret = qcom_smem_alloc_global(__smem, item, size);
+
+ hwspin_unlock_irqrestore(__smem->hwlock, &flags);
+
+ return ret;
+}
+EXPORT_SYMBOL(qcom_smem_alloc);
+
+static int qcom_smem_get_global(struct qcom_smem *smem,
+ unsigned item,
+ void **ptr,
+ size_t *size)
+{
+ struct smem_header *header;
+ struct smem_region *area;
+ struct smem_global_entry *entry;
+ u32 aux_base;
+ unsigned i;
+
+ if (WARN_ON(item >= SMEM_ITEM_COUNT))
+ return -EINVAL;
+
+ header = smem->regions[0].virt_base;
+ entry = &header->toc[item];
+ if (!entry->allocated)
+ return -ENXIO;
+
+ if (ptr != NULL) {
+ aux_base = entry->aux_base & AUX_BASE_MASK;
+
+ for (i = 0; i < smem->num_regions; i++) {
+ area = &smem->regions[i];
+
+ if (area->aux_base == aux_base || !aux_base) {
+ *ptr = area->virt_base + entry->offset;
+ break;
+ }
+ }
+ }
+ if (size != NULL)
+ *size = entry->size;
+
+ return 0;
+}
+
+static int qcom_smem_get_private(struct qcom_smem *smem,
+ unsigned host,
+ unsigned item,
+ void **ptr,
+ size_t *size)
+{
+ struct smem_partition_header *phdr;
+ struct smem_private_entry *hdr;
+ void *p;
+
+ /* We're not going to find it if there's no matching partition */
+ if (host >= SMEM_HOST_COUNT || !smem->partitions[host])
+ return -ENOENT;
+
+ phdr = smem->partitions[host];
+
+ p = (void *)phdr + sizeof(*phdr);
+ while (p < (void *)phdr + phdr->offset_free_uncached) {
+ hdr = p;
+
+ if (hdr->canary != SMEM_PRIVATE_CANARY) {
+ dev_err(smem->dev,
+ "Found invalid canary in host %d partition\n",
+ host);
+ return -EINVAL;
+ }
+
+ if (hdr->item == item) {
+ if (ptr != NULL)
+ *ptr = p + sizeof(*hdr) + hdr->padding_hdr;
+
+ if (size != NULL)
+ *size = hdr->size - hdr->padding_data;
+
+ return 0;
+ }
+
+ p += sizeof(*hdr) + hdr->padding_hdr + hdr->size;
+ }
+
+ return -ENOENT;
+}
+
+/**
+ * qcom_smem_get() - resolve ptr of size of a smem item
+ * @host: the remote processor, or -1
+ * @item: smem item handle
+ * @ptr: pointer to be filled out with address of the item
+ * @size: pointer to be filled out with size of the item
+ *
+ * Looks up pointer and size of a smem item.
+ */
+int qcom_smem_get(unsigned host, unsigned item, void **ptr, size_t *size)
+{
+ unsigned long flags;
+ int ret;
+
+ if (!__smem)
+ return -EPROBE_DEFER;
+
+ ret = hwspin_lock_timeout_irqsave(__smem->hwlock,
+ HWSPINLOCK_TIMEOUT,
+ &flags);
+ if (ret)
+ return ret;
+
+ ret = qcom_smem_get_private(__smem, host, item, ptr, size);
+ if (ret == -ENOENT)
+ ret = qcom_smem_get_global(__smem, item, ptr, size);
+
+ hwspin_unlock_irqrestore(__smem->hwlock, &flags);
+ return ret;
+
+}
+EXPORT_SYMBOL(qcom_smem_get);
+
+/**
+ * qcom_smem_get_free_space() - retrieve amount of free space in a partition
+ * @host: the remote processor identifying a partition, or -1
+ *
+ * To be used by smem clients as a quick way to determine if any new
+ * allocations has been made.
+ */
+int qcom_smem_get_free_space(unsigned host)
+{
+ struct smem_partition_header *phdr;
+ struct smem_header *header;
+ unsigned ret;
+
+ if (!__smem)
+ return -EPROBE_DEFER;
+
+ if (host < SMEM_HOST_COUNT && __smem->partitions[host]) {
+ phdr = __smem->partitions[host];
+ ret = phdr->offset_free_cached - phdr->offset_free_uncached;
+ } else {
+ header = __smem->regions[0].virt_base;
+ ret = header->available;
+ }
+
+ return ret;
+}
+EXPORT_SYMBOL(qcom_smem_get_free_space);
+
+static int qcom_smem_get_sbl_version(struct qcom_smem *smem)
+{
+ unsigned *versions;
+ size_t size;
+ int ret;
+
+ ret = qcom_smem_get_global(smem, SMEM_ITEM_VERSION,
+ (void **)&versions, &size);
+ if (ret < 0) {
+ dev_err(smem->dev, "Unable to read the version item\n");
+ return -ENOENT;
+ }
+
+ if (size < sizeof(unsigned) * SMEM_MASTER_SBL_VERSION_INDEX) {
+ dev_err(smem->dev, "Version item is too small\n");
+ return -EINVAL;
+ }
+
+ return versions[SMEM_MASTER_SBL_VERSION_INDEX];
+}
+
+static int qcom_smem_enumerate_partitions(struct qcom_smem *smem,
+ unsigned local_host)
+{
+ struct smem_partition_header *header;
+ struct smem_ptable_entry *entry;
+ struct smem_ptable *ptable;
+ unsigned remote_host;
+ int i;
+
+ ptable = smem->regions[0].virt_base + smem->regions[0].size - SZ_4K;
+ if (ptable->magic != SMEM_PTABLE_MAGIC)
+ return 0;
+
+ if (ptable->version != 1) {
+ dev_err(smem->dev,
+ "Unsupported partition header version %d\n",
+ ptable->version);
+ return -EINVAL;
+ }
+
+ for (i = 0; i < ptable->num_entries; i++) {
+ entry = &ptable->entry[i];
+
+ if (entry->host0 != local_host && entry->host1 != local_host)
+ continue;
+
+ if (!entry->offset)
+ continue;
+
+ if (!entry->size)
+ continue;
+
+ if (entry->host0 == local_host)
+ remote_host = entry->host1;
+ else
+ remote_host = entry->host0;
+
+ if (remote_host >= SMEM_HOST_COUNT) {
+ dev_err(smem->dev,
+ "Invalid remote host %d\n",
+ remote_host);
+ return -EINVAL;
+ }
+
+ if (smem->partitions[remote_host]) {
+ dev_err(smem->dev,
+ "Already found a partition for host %d\n",
+ remote_host);
+ return -EINVAL;
+ }
+
+ header = smem->regions[0].virt_base + entry->offset;
+
+ if (header->magic != SMEM_PART_MAGIC) {
+ dev_err(smem->dev,
+ "Partition %d has invalid magic\n", i);
+ return -EINVAL;
+ }
+
+ if (header->host0 != local_host && header->host1 != local_host) {
+ dev_err(smem->dev,
+ "Partition %d hosts are invalid\n", i);
+ return -EINVAL;
+ }
+
+ if (header->host0 != remote_host && header->host1 != remote_host) {
+ dev_err(smem->dev,
+ "Partition %d hosts are invalid\n", i);
+ return -EINVAL;
+ }
+
+ if (header->size != entry->size) {
+ dev_err(smem->dev,
+ "Partition %d has invalid size\n", i);
+ return -EINVAL;
+ }
+
+ if (header->offset_free_uncached > header->size) {
+ dev_err(smem->dev,
+ "Partition %d has invalid free pointer\n", i);
+ return -EINVAL;
+ }
+
+ smem->partitions[remote_host] = header;
+ }
+
+ return 0;
+}
+
+static int qcom_smem_count_mem_regions(struct platform_device *pdev)
+{
+ struct resource *res;
+ int num_regions = 0;
+ int i;
+
+ for (i = 0; i < pdev->num_resources; i++) {
+ res = &pdev->resource[i];
+
+ if (resource_type(res) == IORESOURCE_MEM)
+ num_regions++;
+ }
+
+ return num_regions;
+}
+
+static int qcom_smem_probe(struct platform_device *pdev)
+{
+ struct smem_header *header;
+ struct device_node *np;
+ struct qcom_smem *smem;
+ struct resource *res;
+ struct resource r;
+ size_t array_size;
+ int num_regions = 0;
+ int hwlock_id;
+ u32 version;
+ int ret;
+ int i;
+
+ num_regions = qcom_smem_count_mem_regions(pdev) + 1;
+
+ array_size = num_regions * sizeof(struct smem_region);
+ smem = devm_kzalloc(&pdev->dev, sizeof(*smem) + array_size, GFP_KERNEL);
+ if (!smem)
+ return -ENOMEM;
+
+ smem->dev = &pdev->dev;
+ smem->num_regions = num_regions;
+
+ np = of_parse_phandle(pdev->dev.of_node, "memory-region", 0);
+ if (!np) {
+ dev_err(&pdev->dev, "No memory-region specified\n");
+ return -EINVAL;
+ }
+
+ ret = of_address_to_resource(np, 0, &r);
+ of_node_put(np);
+ if (ret)
+ return ret;
+
+ smem->regions[0].aux_base = (u32)r.start;
+ smem->regions[0].size = resource_size(&r);
+ smem->regions[0].virt_base = devm_ioremap_nocache(&pdev->dev,
+ r.start,
+ resource_size(&r));
+ if (!smem->regions[0].virt_base)
+ return -ENOMEM;
+
+ for (i = 1; i < num_regions; i++) {
+ res = platform_get_resource(pdev, IORESOURCE_MEM, i - 1);
+
+ smem->regions[i].aux_base = (u32)res->start;
+ smem->regions[i].size = resource_size(res);
+ smem->regions[i].virt_base = devm_ioremap_nocache(&pdev->dev,
+ res->start,
+ resource_size(res));
+ if (!smem->regions[i].virt_base)
+ return -ENOMEM;
+ }
+
+ header = smem->regions[0].virt_base;
+ if (header->initialized != 1 || header->reserved) {
+ dev_err(&pdev->dev, "SMEM is not initialized by SBL\n");
+ return -EINVAL;
+ }
+
+ version = qcom_smem_get_sbl_version(smem);
+ if (version >> 16 != SMEM_EXPECTED_VERSION) {
+ dev_err(&pdev->dev, "Unsupported SMEM version 0x%x\n", version);
+ return -EINVAL;
+ }
+
+ ret = qcom_smem_enumerate_partitions(smem, SMEM_HOST_APPS);
+ if (ret < 0)
+ return ret;
+
+ hwlock_id = of_hwspin_lock_get_id(pdev->dev.of_node, 0);
+ if (hwlock_id < 0) {
+ dev_err(&pdev->dev, "failed to retrieve hwlock\n");
+ return hwlock_id;
+ }
+
+ smem->hwlock = hwspin_lock_request_specific(hwlock_id);
+ if (!smem->hwlock)
+ return -ENXIO;
+
+ __smem = smem;
+
+ return 0;
+}
+
+static int qcom_smem_remove(struct platform_device *pdev)
+{
+ __smem = NULL;
+ hwspin_lock_free(__smem->hwlock);
+
+ return 0;
+}
+
+static const struct of_device_id qcom_smem_of_match[] = {
+ { .compatible = "qcom,smem" },
+ {}
+};
+MODULE_DEVICE_TABLE(of, qcom_smem_of_match);
+
+static struct platform_driver qcom_smem_driver = {
+ .probe = qcom_smem_probe,
+ .remove = qcom_smem_remove,
+ .driver = {
+ .name = "qcom-smem",
+ .of_match_table = qcom_smem_of_match,
+ .suppress_bind_attrs = true,
+ },
+};
+
+static int __init qcom_smem_init(void)
+{
+ return platform_driver_register(&qcom_smem_driver);
+}
+arch_initcall(qcom_smem_init);
+
+static void __exit qcom_smem_exit(void)
+{
+ platform_driver_unregister(&qcom_smem_driver);
+}
+module_exit(qcom_smem_exit)
+
+MODULE_AUTHOR("Bjorn Andersson <bjorn.andersson@sonymobile.com>");
+MODULE_DESCRIPTION("Qualcomm Shared Memory Manager");
+MODULE_LICENSE("GPL v2");
diff --git a/include/linux/soc/qcom/smem.h b/include/linux/soc/qcom/smem.h
new file mode 100644
index 0000000..bc9630d
--- /dev/null
+++ b/include/linux/soc/qcom/smem.h
@@ -0,0 +1,11 @@
+#ifndef __QCOM_SMEM_H__
+#define __QCOM_SMEM_H__
+
+#define QCOM_SMEM_HOST_ANY -1
+
+int qcom_smem_alloc(unsigned host, unsigned item, size_t size);
+int qcom_smem_get(unsigned host, unsigned item, void **ptr, size_t *size);
+
+int qcom_smem_get_free_space(unsigned host);
+
+#endif
--
1.9.3 (Apple Git-50)
^ permalink raw reply related [flat|nested] 39+ messages in thread* Re: [PATCH v2 02/11] soc: qcom: Add Shared Memory Manager driver
2015-06-26 21:50 ` [PATCH v2 02/11] soc: qcom: Add Shared Memory Manager driver bjorn
@ 2015-07-17 21:15 ` Andy Gross
2015-07-23 20:47 ` Andy Gross
1 sibling, 0 replies; 39+ messages in thread
From: Andy Gross @ 2015-07-17 21:15 UTC (permalink / raw)
To: bjorn; +Cc: Kumar Gala, Jeffrey Hugo, linux-kernel, linux-arm-msm, linux-soc
On Fri, Jun 26, 2015 at 02:50:10PM -0700, bjorn@kryo.se wrote:
> From: Bjorn Andersson <bjorn.andersson@sonymobile.com>
>
> The Shared Memory Manager driver implements an interface for allocating
> and accessing items in the memory area shared among all of the
> processors in a Qualcomm platform.
>
> Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Andy Gross <agross@codeaurora.org>
--
Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply [flat|nested] 39+ messages in thread
* Re: [PATCH v2 02/11] soc: qcom: Add Shared Memory Manager driver
2015-06-26 21:50 ` [PATCH v2 02/11] soc: qcom: Add Shared Memory Manager driver bjorn
2015-07-17 21:15 ` Andy Gross
@ 2015-07-23 20:47 ` Andy Gross
1 sibling, 0 replies; 39+ messages in thread
From: Andy Gross @ 2015-07-23 20:47 UTC (permalink / raw)
To: bjorn; +Cc: Kumar Gala, Jeffrey Hugo, linux-kernel, linux-arm-msm, linux-soc
On Fri, Jun 26, 2015 at 02:50:10PM -0700, bjorn@kryo.se wrote:
> From: Bjorn Andersson <bjorn.andersson@sonymobile.com>
>
> The Shared Memory Manager driver implements an interface for allocating
> and accessing items in the memory area shared among all of the
> processors in a Qualcomm platform.
>
> Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
> ---
Applied, thanks!
--
Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply [flat|nested] 39+ messages in thread
* [PATCH v2 03/11] soc: qcom: Add device tree binding for Shared Memory Device
2015-06-26 21:50 [PATCH v2 00/11] Qualcomm Shared Memory & RPM drivers bjorn
[not found] ` <1435355419-23602-1-git-send-email-bjorn.andersson-/MT0OVThwyLZJqsBc5GL+g@public.gmane.org>
2015-06-26 21:50 ` [PATCH v2 02/11] soc: qcom: Add Shared Memory Manager driver bjorn
@ 2015-06-26 21:50 ` bjorn
2015-06-26 21:50 ` [PATCH v2 04/11] soc: qcom: Add Shared Memory Driver bjorn
` (7 subsequent siblings)
10 siblings, 0 replies; 39+ messages in thread
From: bjorn @ 2015-06-26 21:50 UTC (permalink / raw)
To: Andy Gross, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell,
Kumar Gala
Cc: devicetree, linux-kernel, Jeffrey Hugo, linux-arm-msm
From: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Add device tree binding documentation for the Qualcomm Shared Memory
Device, used for communication between the various CPUs in the Qualcomm
SoCs.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
---
.../devicetree/bindings/soc/qcom/qcom,smd.txt | 79 ++++++++++++++++++++++
1 file changed, 79 insertions(+)
create mode 100644 Documentation/devicetree/bindings/soc/qcom/qcom,smd.txt
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smd.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,smd.txt
new file mode 100644
index 0000000..f65c76d
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smd.txt
@@ -0,0 +1,79 @@
+Qualcomm Shared Memory Driver (SMD) binding
+
+This binding describes the Qualcomm Shared Memory Driver, a fifo based
+communication channel for sending data between the various subsystems in
+Qualcomm platforms.
+
+- compatible:
+ Usage: required
+ Value type: <stringlist>
+ Definition: must be "qcom,smd"
+
+= EDGES
+
+Each subnode of the SMD node represents a remote subsystem or a remote
+processor of some sort - or in SMD language an "edge". The name of the edges
+are not important.
+The edge is described by the following properties:
+
+- interrupts:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: should specify the IRQ used by the remote processor to
+ signal this processor about communication related updates
+
+- qcom,ipc:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: three entries specifying the outgoing ipc bit used for
+ signaling the remote processor:
+ - phandle to a syscon node representing the apcs registers
+ - u32 representing offset to the register within the syscon
+ - u32 representing the ipc bit within the register
+
+- qcom,smd-edge:
+ Usage: required
+ Value type: <u32>
+ Definition: the identifier of the remote processor in the smd channel
+ allocation table
+
+= SMD DEVICES
+
+In turn, subnodes of the "edges" represent devices tied to SMD channels on that
+"edge". The names of the devices are not important. The properties of these
+nodes are defined by the individual bindings for the SMD devices - but must
+contain the following property:
+
+- qcom,smd-channels:
+ Usage: required
+ Value type: <stringlist>
+ Definition: a list of channels tied to this device, used for matching
+ the device to channels
+
+= EXAMPLE
+
+The following example represents a smd node, with one edge representing the
+"rpm" subsystem. For the "rpm" subsystem we have a device tied to the
+"rpm_request" channel.
+
+ apcs: syscon@f9011000 {
+ compatible = "syscon";
+ reg = <0xf9011000 0x1000>;
+ };
+
+ smd {
+ compatible = "qcom,smd";
+
+ rpm {
+ interrupts = <0 168 1>;
+ qcom,ipc = <&apcs 8 0>;
+ qcom,smd-edge = <15>;
+
+ rpm_requests {
+ compatible = "qcom,rpm-msm8974";
+ qcom,smd-channels = "rpm_requests";
+
+ ...
+ };
+ };
+ };
--
1.9.3 (Apple Git-50)
^ permalink raw reply related [flat|nested] 39+ messages in thread* [PATCH v2 04/11] soc: qcom: Add Shared Memory Driver
2015-06-26 21:50 [PATCH v2 00/11] Qualcomm Shared Memory & RPM drivers bjorn
` (2 preceding siblings ...)
2015-06-26 21:50 ` [PATCH v2 03/11] soc: qcom: Add device tree binding for Shared Memory Device bjorn
@ 2015-06-26 21:50 ` bjorn
2015-07-07 13:45 ` Georgi Djakov
2015-06-26 21:50 ` [PATCH v2 05/11] mfd: devicetree: bindings: Add Qualcomm SMD based RPM DT binding bjorn
` (6 subsequent siblings)
10 siblings, 1 reply; 39+ messages in thread
From: bjorn @ 2015-06-26 21:50 UTC (permalink / raw)
To: Kumar Gala, Andy Gross, David Brown
Cc: linux-kernel, linux-soc, Jeffrey Hugo, linux-arm-msm
From: Bjorn Andersson <bjorn.andersson@sonymobile.com>
This adds the Qualcomm Shared Memory Driver (SMD) providing
communication channels to remote processors, ontop of SMEM.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
---
drivers/soc/qcom/Kconfig | 8 +
drivers/soc/qcom/Makefile | 1 +
drivers/soc/qcom/smd.c | 1324 ++++++++++++++++++++++++++++++++++++++++++
include/linux/soc/qcom/smd.h | 46 ++
4 files changed, 1379 insertions(+)
create mode 100644 drivers/soc/qcom/smd.c
create mode 100644 include/linux/soc/qcom/smd.h
diff --git a/drivers/soc/qcom/Kconfig b/drivers/soc/qcom/Kconfig
index 0e115c0..893c5db 100644
--- a/drivers/soc/qcom/Kconfig
+++ b/drivers/soc/qcom/Kconfig
@@ -20,6 +20,14 @@ config QCOM_PM
modes. It interface with various system drivers to put the cores in
low power modes.
+config QCOM_SMD
+ tristate "Qualcomm Shared Memory Driver (SMD)"
+ depends on QCOM_SMEM
+ help
+ Say y here to enable support for the Qualcomm Shared Memory Driver
+ providing communication channels to remote processors in Qualcomm
+ platforms.
+
config QCOM_SMEM
tristate "Qualcomm Shared Memory Manager (SMEM)"
depends on ARCH_QCOM
diff --git a/drivers/soc/qcom/Makefile b/drivers/soc/qcom/Makefile
index 3a033c4..f961a87 100644
--- a/drivers/soc/qcom/Makefile
+++ b/drivers/soc/qcom/Makefile
@@ -1,3 +1,4 @@
obj-$(CONFIG_QCOM_GSBI) += qcom_gsbi.o
obj-$(CONFIG_QCOM_PM) += spm.o
+obj-$(CONFIG_QCOM_SMD) += smd.o
obj-$(CONFIG_QCOM_SMEM) += smem.o
diff --git a/drivers/soc/qcom/smd.c b/drivers/soc/qcom/smd.c
new file mode 100644
index 0000000..a1fc882
--- /dev/null
+++ b/drivers/soc/qcom/smd.c
@@ -0,0 +1,1324 @@
+/*
+ * Copyright (c) 2015, Sony Mobile Communications AB.
+ * Copyright (c) 2012-2013, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/soc/qcom/smd.h>
+#include <linux/soc/qcom/smem.h>
+#include <linux/wait.h>
+
+/*
+ * The Qualcomm Shared Memory communication solution provides point-to-point
+ * channels for clients to send and receive streaming or packet based data.
+ *
+ * Each channel consists of a control item (channel info) and a ring buffer
+ * pair. The channel info carry information related to channel state, flow
+ * control and the offsets within the ring buffer.
+ *
+ * All allocated channels are listed in an allocation table, identifying the
+ * pair of items by name, type and remote processor.
+ *
+ * Upon creating a new channel the remote processor allocates channel info and
+ * ring buffer items from the smem heap and populate the allocation table. An
+ * interrupt is sent to the other end of the channel and a scan for new
+ * channels should be done. A channel never goes away, it will only change
+ * state.
+ *
+ * The remote processor signals it intent for bring up the communication
+ * channel by setting the state of its end of the channel to "opening" and
+ * sends out an interrupt. We detect this change and register a smd device to
+ * consume the channel. Upon finding a consumer we finish the handshake and the
+ * channel is up.
+ *
+ * Upon closing a channel, the remote processor will update the state of its
+ * end of the channel and signal us, we will then unregister any attached
+ * device and close our end of the channel.
+ *
+ * Devices attached to a channel can use the qcom_smd_send function to push
+ * data to the channel, this is done by copying the data into the tx ring
+ * buffer, updating the pointers in the channel info and signaling the remote
+ * processor.
+ *
+ * The remote processor does the equivalent when it transfer data and upon
+ * receiving the interrupt we check the channel info for new data and delivers
+ * this to the attached device. If the device is not ready to receive the data
+ * we leave it in the ring buffer for now.
+ */
+
+struct smd_channel_info;
+struct smd_channel_info_word;
+
+#define SMD_ALLOC_TBL_COUNT 2
+#define SMD_ALLOC_TBL_SIZE 64
+
+/*
+ * This lists the various smem heap items relevant for the allocation table and
+ * smd channel entries.
+ */
+static const struct {
+ unsigned alloc_tbl_id;
+ unsigned info_base_id;
+ unsigned fifo_base_id;
+} smem_items[SMD_ALLOC_TBL_COUNT] = {
+ {
+ .alloc_tbl_id = 13,
+ .info_base_id = 14,
+ .fifo_base_id = 338
+ },
+ {
+ .alloc_tbl_id = 14,
+ .info_base_id = 266,
+ .fifo_base_id = 202,
+ },
+};
+
+/**
+ * struct qcom_smd_edge - representing a remote processor
+ * @smd: handle to qcom_smd
+ * @of_node: of_node handle for information related to this edge
+ * @edge_id: identifier of this edge
+ * @irq: interrupt for signals on this edge
+ * @ipc_regmap: regmap handle holding the outgoing ipc register
+ * @ipc_offset: offset within @ipc_regmap of the register for ipc
+ * @ipc_bit: bit in the register at @ipc_offset of @ipc_regmap
+ * @channels: list of all channels detected on this edge
+ * @channels_lock: guard for modifications of @channels
+ * @need_rescan: flag that the @work needs to scan smem for new channels
+ * @smem_available: last available amount of smem triggering a channel scan
+ * @work: work item for edge house keeping
+ */
+struct qcom_smd_edge {
+ struct qcom_smd *smd;
+ struct device_node *of_node;
+ unsigned edge_id;
+
+ int irq;
+
+ struct regmap *ipc_regmap;
+ int ipc_offset;
+ int ipc_bit;
+
+ struct list_head channels;
+ spinlock_t channels_lock;
+
+ bool need_rescan;
+ unsigned smem_available;
+
+ struct work_struct work;
+};
+
+/*
+ * SMD channel states.
+ */
+enum smd_channel_state {
+ SMD_CHANNEL_CLOSED,
+ SMD_CHANNEL_OPENING,
+ SMD_CHANNEL_OPENED,
+ SMD_CHANNEL_FLUSHING,
+ SMD_CHANNEL_CLOSING,
+ SMD_CHANNEL_RESET,
+ SMD_CHANNEL_RESET_OPENING
+};
+
+/**
+ * struct qcom_smd_channel - smd channel struct
+ * @edge: qcom_smd_edge this channel is living on
+ * @qsdev: reference to a associated smd client device
+ * @name: name of the channel
+ * @state: local state of the channel
+ * @remote_state: remote state of the channel
+ * @tx_info: byte aligned outgoing channel info
+ * @rx_info: byte aligned incoming channel info
+ * @tx_info_word: word aligned outgoing channel info
+ * @rx_info_word: word aligned incoming channel info
+ * @tx_lock: lock to make writes to the channel mutually exclusive
+ * @fblockread_event: wakeup event tied to tx fBLOCKREADINTR
+ * @tx_fifo: pointer to the outgoing ring buffer
+ * @rx_fifo: pointer to the incoming ring buffer
+ * @fifo_size: size of each ring buffer
+ * @bounce_buffer: bounce buffer for reading wrapped packets
+ * @cb: callback function registered for this channel
+ * @recv_lock: guard for rx info modifications and cb pointer
+ * @pkt_size: size of the currently handled packet
+ * @list: lite entry for @channels in qcom_smd_edge
+ */
+struct qcom_smd_channel {
+ struct qcom_smd_edge *edge;
+
+ struct qcom_smd_device *qsdev;
+
+ char *name;
+ enum smd_channel_state state;
+ enum smd_channel_state remote_state;
+
+ struct smd_channel_info *tx_info;
+ struct smd_channel_info *rx_info;
+
+ struct smd_channel_info_word *tx_info_word;
+ struct smd_channel_info_word *rx_info_word;
+
+ struct mutex tx_lock;
+ wait_queue_head_t fblockread_event;
+
+ void *tx_fifo;
+ void *rx_fifo;
+ int fifo_size;
+
+ void *bounce_buffer;
+ int (*cb)(struct qcom_smd_device *, const void *, size_t);
+
+ spinlock_t recv_lock;
+
+ int pkt_size;
+
+ struct list_head list;
+};
+
+/**
+ * struct qcom_smd - smd struct
+ * @dev: device struct
+ * @allocated: bitmap representing already allocated channels
+ * @alloc_tbl: pointer(s) to the allocation table(s)
+ * @alloc_tbl_entries: number of actual allocation entries found
+ * @num_edges: number of entries in @edges
+ * @edges: array of edges to be handled
+ */
+struct qcom_smd {
+ struct device *dev;
+
+ DECLARE_BITMAP(allocated, SMD_ALLOC_TBL_COUNT * SMD_ALLOC_TBL_SIZE);
+ struct qcom_smd_alloc_entry *alloc_tbl[SMD_ALLOC_TBL_COUNT];
+ unsigned alloc_tbl_entries;
+
+ unsigned num_edges;
+ struct qcom_smd_edge edges[0];
+};
+
+/*
+ * Format of the smd_info smem items, for byte aligned channels.
+ */
+struct smd_channel_info {
+ u32 state;
+ u8 fDSR;
+ u8 fCTS;
+ u8 fCD;
+ u8 fRI;
+ u8 fHEAD;
+ u8 fTAIL;
+ u8 fSTATE;
+ u8 fBLOCKREADINTR;
+ u32 tail;
+ u32 head;
+};
+
+/*
+ * Format of the smd_info smem items, for word aligned channels.
+ */
+struct smd_channel_info_word {
+ u32 state;
+ u32 fDSR;
+ u32 fCTS;
+ u32 fCD;
+ u32 fRI;
+ u32 fHEAD;
+ u32 fTAIL;
+ u32 fSTATE;
+ u32 fBLOCKREADINTR;
+ u32 tail;
+ u32 head;
+};
+
+#define GET_RX_CHANNEL_INFO(channel, param) \
+ (channel->rx_info_word ? \
+ channel->rx_info_word->param : \
+ channel->rx_info->param)
+
+#define SET_RX_CHANNEL_INFO(channel, param, value) \
+ (channel->rx_info_word ? \
+ (channel->rx_info_word->param = value) : \
+ (channel->rx_info->param = value))
+
+#define GET_TX_CHANNEL_INFO(channel, param) \
+ (channel->rx_info_word ? \
+ channel->tx_info_word->param : \
+ channel->tx_info->param)
+
+#define SET_TX_CHANNEL_INFO(channel, param, value) \
+ (channel->rx_info_word ? \
+ (channel->tx_info_word->param = value) : \
+ (channel->tx_info->param = value))
+
+/**
+ * struct qcom_smd_alloc_entry - channel allocation entry
+ * @name: channel name
+ * @cid: channel index
+ * @flags: channel flags and edge id
+ * @ref_count: reference count of the channel
+ */
+struct qcom_smd_alloc_entry {
+ u8 name[20];
+ u32 cid;
+ u32 flags;
+ u32 ref_count;
+} __packed;
+
+#define SMD_CHANNEL_FLAGS_EDGE_MASK 0xff
+#define SMD_CHANNEL_FLAGS_STREAM BIT(8)
+#define SMD_CHANNEL_FLAGS_PACKET BIT(9)
+
+/*
+ * Each smd packet contains a 20 byte header, with the first 4 being the length
+ * of the packet.
+ */
+#define SMD_PACKET_HEADER_LEN 20
+
+/*
+ * Signal the remote processor associated with 'channel'.
+ */
+static void qcom_smd_signal_channel(struct qcom_smd_channel *channel)
+{
+ struct qcom_smd_edge *edge = channel->edge;
+
+ regmap_write(edge->ipc_regmap, edge->ipc_offset, BIT(edge->ipc_bit));
+}
+
+/*
+ * Initialize the tx channel info
+ */
+static void qcom_smd_channel_reset(struct qcom_smd_channel *channel)
+{
+ SET_TX_CHANNEL_INFO(channel, state, SMD_CHANNEL_CLOSED);
+ SET_TX_CHANNEL_INFO(channel, fDSR, 0);
+ SET_TX_CHANNEL_INFO(channel, fCTS, 0);
+ SET_TX_CHANNEL_INFO(channel, fCD, 0);
+ SET_TX_CHANNEL_INFO(channel, fRI, 0);
+ SET_TX_CHANNEL_INFO(channel, fHEAD, 0);
+ SET_TX_CHANNEL_INFO(channel, fTAIL, 0);
+ SET_TX_CHANNEL_INFO(channel, fSTATE, 1);
+ SET_TX_CHANNEL_INFO(channel, fBLOCKREADINTR, 0);
+ SET_TX_CHANNEL_INFO(channel, head, 0);
+ SET_TX_CHANNEL_INFO(channel, tail, 0);
+
+ qcom_smd_signal_channel(channel);
+
+ channel->state = SMD_CHANNEL_CLOSED;
+ channel->pkt_size = 0;
+}
+
+/*
+ * Calculate the amount of data available in the rx fifo
+ */
+static size_t qcom_smd_channel_get_rx_avail(struct qcom_smd_channel *channel)
+{
+ unsigned head;
+ unsigned tail;
+
+ head = GET_RX_CHANNEL_INFO(channel, head);
+ tail = GET_RX_CHANNEL_INFO(channel, tail);
+
+ return (head - tail) & (channel->fifo_size - 1);
+}
+
+/*
+ * Set tx channel state and inform the remote processor
+ */
+static void qcom_smd_channel_set_state(struct qcom_smd_channel *channel,
+ int state)
+{
+ struct qcom_smd_edge *edge = channel->edge;
+ bool is_open = state == SMD_CHANNEL_OPENED;
+
+ if (channel->state == state)
+ return;
+
+ dev_dbg(edge->smd->dev, "set_state(%s, %d)\n", channel->name, state);
+
+ SET_TX_CHANNEL_INFO(channel, fDSR, is_open);
+ SET_TX_CHANNEL_INFO(channel, fCTS, is_open);
+ SET_TX_CHANNEL_INFO(channel, fCD, is_open);
+
+ SET_TX_CHANNEL_INFO(channel, state, state);
+ SET_TX_CHANNEL_INFO(channel, fSTATE, 1);
+
+ channel->state = state;
+ qcom_smd_signal_channel(channel);
+}
+
+/*
+ * Copy count bytes of data using 32bit accesses, if that's required.
+ */
+static void smd_copy_to_fifo(void __iomem *_dst,
+ const void *_src,
+ size_t count,
+ bool word_aligned)
+{
+ u32 *dst = (u32 *)_dst;
+ u32 *src = (u32 *)_src;
+
+ if (word_aligned) {
+ count /= sizeof(u32);
+ while (count--)
+ writel_relaxed(*src++, dst++);
+ } else {
+ memcpy(_dst, _src, count);
+ }
+}
+
+/*
+ * Copy count bytes of data using 32bit accesses, if that is required.
+ */
+static void smd_copy_from_fifo(void *_dst,
+ const void __iomem *_src,
+ size_t count,
+ bool word_aligned)
+{
+ u32 *dst = (u32 *)_dst;
+ u32 *src = (u32 *)_src;
+
+ if (word_aligned) {
+ count /= sizeof(u32);
+ while (count--)
+ *dst++ = readl_relaxed(src++);
+ } else {
+ memcpy(_dst, _src, count);
+ }
+}
+
+/*
+ * Read count bytes of data from the rx fifo into buf, but don't advance the
+ * tail.
+ */
+static size_t qcom_smd_channel_peek(struct qcom_smd_channel *channel,
+ void *buf, size_t count)
+{
+ bool word_aligned;
+ unsigned tail;
+ size_t len;
+
+ word_aligned = channel->rx_info_word != NULL;
+ tail = GET_RX_CHANNEL_INFO(channel, tail);
+
+ len = min_t(size_t, count, channel->fifo_size - tail);
+ if (len) {
+ smd_copy_from_fifo(buf,
+ channel->rx_fifo + tail,
+ len,
+ word_aligned);
+ }
+
+ if (len != count) {
+ smd_copy_from_fifo(buf + len,
+ channel->rx_fifo,
+ count - len,
+ word_aligned);
+ }
+
+ return count;
+}
+
+/*
+ * Advance the rx tail by count bytes.
+ */
+static void qcom_smd_channel_advance(struct qcom_smd_channel *channel,
+ size_t count)
+{
+ unsigned tail;
+
+ tail = GET_RX_CHANNEL_INFO(channel, tail);
+ tail += count;
+ tail &= (channel->fifo_size - 1);
+ SET_RX_CHANNEL_INFO(channel, tail, tail);
+}
+
+/*
+ * Read out a single packet from the rx fifo and deliver it to the device
+ */
+static int qcom_smd_channel_recv_single(struct qcom_smd_channel *channel)
+{
+ struct qcom_smd_device *qsdev = channel->qsdev;
+ unsigned tail;
+ size_t len;
+ void *ptr;
+ int ret;
+
+ if (!channel->cb)
+ return 0;
+
+ tail = GET_RX_CHANNEL_INFO(channel, tail);
+
+ /* Use bounce buffer if the data wraps */
+ if (tail + channel->pkt_size >= channel->fifo_size) {
+ ptr = channel->bounce_buffer;
+ len = qcom_smd_channel_peek(channel, ptr, channel->pkt_size);
+ } else {
+ ptr = channel->rx_fifo + tail;
+ len = channel->pkt_size;
+ }
+
+ ret = channel->cb(qsdev, ptr, len);
+ if (ret < 0)
+ return ret;
+
+ /* Only forward the tail if the client consumed the data */
+ qcom_smd_channel_advance(channel, len);
+
+ channel->pkt_size = 0;
+
+ return 0;
+}
+
+/*
+ * Per channel interrupt handling
+ */
+static bool qcom_smd_channel_intr(struct qcom_smd_channel *channel)
+{
+ bool need_state_scan = false;
+ int remote_state;
+ u32 pktlen;
+ int avail;
+ int ret;
+
+ /* Handle state changes */
+ remote_state = GET_RX_CHANNEL_INFO(channel, state);
+ if (remote_state != channel->remote_state) {
+ channel->remote_state = remote_state;
+ need_state_scan = true;
+ }
+ /* Indicate that we have seen any state change */
+ SET_RX_CHANNEL_INFO(channel, fSTATE, 0);
+
+ /* Signal waiting qcom_smd_send() about the interrupt */
+ if (!GET_TX_CHANNEL_INFO(channel, fBLOCKREADINTR))
+ wake_up_interruptible(&channel->fblockread_event);
+
+ /* Don't consume any data until we've opened the channel */
+ if (channel->state != SMD_CHANNEL_OPENED)
+ goto out;
+
+ /* Indicate that we've seen the new data */
+ SET_RX_CHANNEL_INFO(channel, fHEAD, 0);
+
+ /* Consume data */
+ for (;;) {
+ avail = qcom_smd_channel_get_rx_avail(channel);
+
+ if (!channel->pkt_size && avail >= SMD_PACKET_HEADER_LEN) {
+ qcom_smd_channel_peek(channel, &pktlen, sizeof(pktlen));
+ qcom_smd_channel_advance(channel, SMD_PACKET_HEADER_LEN);
+ channel->pkt_size = pktlen;
+ } else if (channel->pkt_size && avail >= channel->pkt_size) {
+ ret = qcom_smd_channel_recv_single(channel);
+ if (ret)
+ break;
+ } else {
+ break;
+ }
+ }
+
+ /* Indicate that we have seen and updated tail */
+ SET_RX_CHANNEL_INFO(channel, fTAIL, 1);
+
+ /* Signal the remote that we've consumed the data (if requested) */
+ if (!GET_RX_CHANNEL_INFO(channel, fBLOCKREADINTR)) {
+ /* Ensure ordering of channel info updates */
+ wmb();
+
+ qcom_smd_signal_channel(channel);
+ }
+
+out:
+ return need_state_scan;
+}
+
+/*
+ * The edge interrupts are triggered by the remote processor on state changes,
+ * channel info updates or when new channels are created.
+ */
+static irqreturn_t qcom_smd_edge_intr(int irq, void *data)
+{
+ struct qcom_smd_edge *edge = data;
+ struct qcom_smd_channel *channel;
+ unsigned available;
+ bool kick_worker = false;
+
+ /*
+ * Handle state changes or data on each of the channels on this edge
+ */
+ spin_lock(&edge->channels_lock);
+ list_for_each_entry(channel, &edge->channels, list) {
+ spin_lock(&channel->recv_lock);
+ kick_worker |= qcom_smd_channel_intr(channel);
+ spin_unlock(&channel->recv_lock);
+ }
+ spin_unlock(&edge->channels_lock);
+
+ /*
+ * Creating a new channel requires allocating an smem entry, so we only
+ * have to scan if the amount of available space in smem have changed
+ * since last scan.
+ */
+ available = qcom_smem_get_free_space(edge->edge_id);
+ if (available != edge->smem_available) {
+ edge->smem_available = available;
+ edge->need_rescan = true;
+ kick_worker = true;
+ }
+
+ if (kick_worker)
+ schedule_work(&edge->work);
+
+ return IRQ_HANDLED;
+}
+
+/*
+ * Delivers any outstanding packets in the rx fifo, can be used after probe of
+ * the clients to deliver any packets that wasn't delivered before the client
+ * was setup.
+ */
+static void qcom_smd_channel_resume(struct qcom_smd_channel *channel)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&channel->recv_lock, flags);
+ qcom_smd_channel_intr(channel);
+ spin_unlock_irqrestore(&channel->recv_lock, flags);
+}
+
+/*
+ * Calculate how much space is available in the tx fifo.
+ */
+static size_t qcom_smd_get_tx_avail(struct qcom_smd_channel *channel)
+{
+ unsigned head;
+ unsigned tail;
+ unsigned mask = channel->fifo_size - 1;
+
+ head = GET_TX_CHANNEL_INFO(channel, head);
+ tail = GET_TX_CHANNEL_INFO(channel, tail);
+
+ return mask - ((head - tail) & mask);
+}
+
+/*
+ * Write count bytes of data into channel, possibly wrapping in the ring buffer
+ */
+static int qcom_smd_write_fifo(struct qcom_smd_channel *channel,
+ const void *data,
+ size_t count)
+{
+ bool word_aligned;
+ unsigned head;
+ size_t len;
+
+ word_aligned = channel->tx_info_word != NULL;
+ head = GET_TX_CHANNEL_INFO(channel, head);
+
+ len = min_t(size_t, count, channel->fifo_size - head);
+ if (len) {
+ smd_copy_to_fifo(channel->tx_fifo + head,
+ data,
+ len,
+ word_aligned);
+ }
+
+ if (len != count) {
+ smd_copy_to_fifo(channel->tx_fifo,
+ data + len,
+ count - len,
+ word_aligned);
+ }
+
+ head += count;
+ head &= (channel->fifo_size - 1);
+ SET_TX_CHANNEL_INFO(channel, head, head);
+
+ return count;
+}
+
+/**
+ * qcom_smd_send - write data to smd channel
+ * @channel: channel handle
+ * @data: buffer of data to write
+ * @len: number of bytes to write
+ *
+ * This is a blocking write of len bytes into the channel's tx ring buffer and
+ * signal the remote end. It will sleep until there is enough space available
+ * in the tx buffer, utilizing the fBLOCKREADINTR signaling mechanism to avoid
+ * polling.
+ */
+int qcom_smd_send(struct qcom_smd_channel *channel, const void *data, int len)
+{
+ u32 hdr[5] = {len,};
+ int tlen = sizeof(hdr) + len;
+ int ret;
+
+ /* Word aligned channels only accept word size aligned data */
+ if (channel->rx_info_word != NULL && len % 4)
+ return -EINVAL;
+
+ ret = mutex_lock_interruptible(&channel->tx_lock);
+ if (ret)
+ return ret;
+
+ while (qcom_smd_get_tx_avail(channel) < tlen) {
+ if (channel->state != SMD_CHANNEL_OPENED) {
+ ret = -EPIPE;
+ goto out;
+ }
+
+ SET_TX_CHANNEL_INFO(channel, fBLOCKREADINTR, 1);
+
+ ret = wait_event_interruptible(channel->fblockread_event,
+ qcom_smd_get_tx_avail(channel) >= tlen ||
+ channel->state != SMD_CHANNEL_OPENED);
+ if (ret)
+ goto out;
+
+ SET_TX_CHANNEL_INFO(channel, fBLOCKREADINTR, 0);
+ }
+
+ SET_TX_CHANNEL_INFO(channel, fTAIL, 0);
+
+ qcom_smd_write_fifo(channel, hdr, sizeof(hdr));
+ qcom_smd_write_fifo(channel, data, len);
+
+ SET_TX_CHANNEL_INFO(channel, fHEAD, 1);
+
+ /* Ensure ordering of channel info updates */
+ wmb();
+
+ qcom_smd_signal_channel(channel);
+
+out:
+ mutex_unlock(&channel->tx_lock);
+
+ return ret;
+}
+EXPORT_SYMBOL(qcom_smd_send);
+
+static struct qcom_smd_device *to_smd_device(struct device *dev)
+{
+ return container_of(dev, struct qcom_smd_device, dev);
+}
+
+static struct qcom_smd_driver *to_smd_driver(struct device *dev)
+{
+ struct qcom_smd_device *qsdev = to_smd_device(dev);
+
+ return container_of(qsdev->dev.driver, struct qcom_smd_driver, driver);
+}
+
+static int qcom_smd_dev_match(struct device *dev, struct device_driver *drv)
+{
+ return of_driver_match_device(dev, drv);
+}
+
+/*
+ * Probe the smd client.
+ *
+ * The remote side have indicated that it want the channel to be opened, so
+ * complete the state handshake and probe our client driver.
+ */
+static int qcom_smd_dev_probe(struct device *dev)
+{
+ struct qcom_smd_device *qsdev = to_smd_device(dev);
+ struct qcom_smd_driver *qsdrv = to_smd_driver(dev);
+ struct qcom_smd_channel *channel = qsdev->channel;
+ size_t bb_size;
+ int ret;
+
+ /*
+ * Packets are maximum 4k, but reduce if the fifo is smaller
+ */
+ bb_size = min(channel->fifo_size, SZ_4K);
+ channel->bounce_buffer = kmalloc(bb_size, GFP_KERNEL);
+ if (!channel->bounce_buffer)
+ return -ENOMEM;
+
+ channel->cb = qsdrv->callback;
+
+ qcom_smd_channel_set_state(channel, SMD_CHANNEL_OPENING);
+
+ qcom_smd_channel_set_state(channel, SMD_CHANNEL_OPENED);
+
+ ret = qsdrv->probe(qsdev);
+ if (ret)
+ goto err;
+
+ qcom_smd_channel_resume(channel);
+
+ return 0;
+
+err:
+ dev_err(&qsdev->dev, "probe failed\n");
+
+ channel->cb = NULL;
+ kfree(channel->bounce_buffer);
+ channel->bounce_buffer = NULL;
+
+ qcom_smd_channel_set_state(channel, SMD_CHANNEL_CLOSED);
+ return ret;
+}
+
+/*
+ * Remove the smd client.
+ *
+ * The channel is going away, for some reason, so remove the smd client and
+ * reset the channel state.
+ */
+static int qcom_smd_dev_remove(struct device *dev)
+{
+ struct qcom_smd_device *qsdev = to_smd_device(dev);
+ struct qcom_smd_driver *qsdrv = to_smd_driver(dev);
+ struct qcom_smd_channel *channel = qsdev->channel;
+ unsigned long flags;
+
+ qcom_smd_channel_set_state(channel, SMD_CHANNEL_CLOSING);
+
+ /*
+ * Make sure we don't race with the code receiving data.
+ */
+ spin_lock_irqsave(&channel->recv_lock, flags);
+ channel->cb = NULL;
+ spin_unlock_irqrestore(&channel->recv_lock, flags);
+
+ /* Wake up any sleepers in qcom_smd_send() */
+ wake_up_interruptible(&channel->fblockread_event);
+
+ /*
+ * We expect that the client might block in remove() waiting for any
+ * outstanding calls to qcom_smd_send() to wake up and finish.
+ */
+ if (qsdrv->remove)
+ qsdrv->remove(qsdev);
+
+ /*
+ * The client is now gone, cleanup and reset the channel state.
+ */
+ channel->qsdev = NULL;
+ kfree(channel->bounce_buffer);
+ channel->bounce_buffer = NULL;
+
+ qcom_smd_channel_set_state(channel, SMD_CHANNEL_CLOSED);
+
+ qcom_smd_channel_reset(channel);
+
+ return 0;
+}
+
+static struct bus_type qcom_smd_bus = {
+ .name = "qcom_smd",
+ .match = qcom_smd_dev_match,
+ .probe = qcom_smd_dev_probe,
+ .remove = qcom_smd_dev_remove,
+};
+
+/*
+ * Release function for the qcom_smd_device object.
+ */
+static void qcom_smd_release_device(struct device *dev)
+{
+ struct qcom_smd_device *qsdev = to_smd_device(dev);
+
+ kfree(qsdev);
+}
+
+/*
+ * Finds the device_node for the smd child interested in this channel.
+ */
+static struct device_node *qcom_smd_match_channel(struct device_node *edge_node,
+ const char *channel)
+{
+ struct device_node *child;
+ const char *name;
+ const char *key;
+ int ret;
+
+ for_each_available_child_of_node(edge_node, child) {
+ key = "qcom,smd-channels";
+ ret = of_property_read_string(child, key, &name);
+ if (ret) {
+ of_node_put(child);
+ continue;
+ }
+
+ if (strcmp(name, channel) == 0)
+ return child;
+ }
+
+ return NULL;
+}
+
+/*
+ * Create a smd client device for channel that is being opened.
+ */
+static int qcom_smd_create_device(struct qcom_smd_channel *channel)
+{
+ struct qcom_smd_device *qsdev;
+ struct qcom_smd_edge *edge = channel->edge;
+ struct device_node *node;
+ struct qcom_smd *smd = edge->smd;
+ int ret;
+
+ if (channel->qsdev)
+ return -EEXIST;
+
+ node = qcom_smd_match_channel(edge->of_node, channel->name);
+ if (!node) {
+ dev_dbg(smd->dev, "no match for '%s'\n", channel->name);
+ return -ENXIO;
+ }
+
+ dev_dbg(smd->dev, "registering '%s'\n", channel->name);
+
+ qsdev = kzalloc(sizeof(*qsdev), GFP_KERNEL);
+ if (!qsdev)
+ return -ENOMEM;
+
+ dev_set_name(&qsdev->dev, "%s.%s", edge->of_node->name, node->name);
+ qsdev->dev.parent = smd->dev;
+ qsdev->dev.bus = &qcom_smd_bus;
+ qsdev->dev.release = qcom_smd_release_device;
+ qsdev->dev.of_node = node;
+
+ qsdev->channel = channel;
+
+ channel->qsdev = qsdev;
+
+ ret = device_register(&qsdev->dev);
+ if (ret) {
+ dev_err(smd->dev, "device_register failed: %d\n", ret);
+ put_device(&qsdev->dev);
+ }
+
+ return ret;
+}
+
+/*
+ * Destroy a smd client device for a channel that's going away.
+ */
+static void qcom_smd_destroy_device(struct qcom_smd_channel *channel)
+{
+ struct device *dev;
+
+ BUG_ON(!channel->qsdev);
+
+ dev = &channel->qsdev->dev;
+
+ device_unregister(dev);
+ of_node_put(dev->of_node);
+ put_device(dev);
+}
+
+/**
+ * qcom_smd_driver_register - register a smd driver
+ * @qsdrv: qcom_smd_driver struct
+ */
+int qcom_smd_driver_register(struct qcom_smd_driver *qsdrv)
+{
+ qsdrv->driver.bus = &qcom_smd_bus;
+ return driver_register(&qsdrv->driver);
+}
+EXPORT_SYMBOL(qcom_smd_driver_register);
+
+/**
+ * qcom_smd_driver_unregister - unregister a smd driver
+ * @qsdrv: qcom_smd_driver struct
+ */
+void qcom_smd_driver_unregister(struct qcom_smd_driver *qsdrv)
+{
+ driver_unregister(&qsdrv->driver);
+}
+EXPORT_SYMBOL(qcom_smd_driver_unregister);
+
+/*
+ * Allocate the qcom_smd_channel object for a newly found smd channel,
+ * retrieving and validating the smem items involved.
+ */
+static struct qcom_smd_channel *qcom_smd_create_channel(struct qcom_smd_edge *edge,
+ unsigned smem_info_item,
+ unsigned smem_fifo_item,
+ char *name)
+{
+ struct qcom_smd_channel *channel;
+ struct qcom_smd *smd = edge->smd;
+ size_t fifo_size;
+ size_t info_size;
+ void *fifo_base;
+ void *info;
+ int ret;
+
+ channel = devm_kzalloc(smd->dev, sizeof(*channel), GFP_KERNEL);
+ if (!channel)
+ return ERR_PTR(-ENOMEM);
+
+ channel->edge = edge;
+ channel->name = devm_kstrdup(smd->dev, name, GFP_KERNEL);
+ if (!channel->name)
+ return ERR_PTR(-ENOMEM);
+
+ mutex_init(&channel->tx_lock);
+ spin_lock_init(&channel->recv_lock);
+ init_waitqueue_head(&channel->fblockread_event);
+
+ ret = qcom_smem_get(edge->edge_id, smem_info_item, (void **)&info, &info_size);
+ if (ret)
+ goto free_name_and_channel;
+
+ /*
+ * Use the size of the item to figure out which channel info struct to
+ * use.
+ */
+ if (info_size == 2 * sizeof(struct smd_channel_info_word)) {
+ channel->tx_info_word = info;
+ channel->rx_info_word = info + sizeof(struct smd_channel_info_word);
+ } else if (info_size == 2 * sizeof(struct smd_channel_info)) {
+ channel->tx_info = info;
+ channel->rx_info = info + sizeof(struct smd_channel_info);
+ } else {
+ dev_err(smd->dev,
+ "channel info of size %zu not supported\n", info_size);
+ ret = -EINVAL;
+ goto free_name_and_channel;
+ }
+
+ ret = qcom_smem_get(edge->edge_id, smem_fifo_item, &fifo_base, &fifo_size);
+ if (ret)
+ goto free_name_and_channel;
+
+ /* The channel consist of a rx and tx fifo of equal size */
+ fifo_size /= 2;
+
+ dev_dbg(smd->dev, "new channel '%s' info-size: %d fifo-size: %zu\n",
+ name, info_size, fifo_size);
+
+ channel->tx_fifo = fifo_base;
+ channel->rx_fifo = fifo_base + fifo_size;
+ channel->fifo_size = fifo_size;
+
+ qcom_smd_channel_reset(channel);
+
+ return channel;
+
+free_name_and_channel:
+ devm_kfree(smd->dev, channel->name);
+ devm_kfree(smd->dev, channel);
+
+ return ERR_PTR(ret);
+}
+
+/*
+ * Scans the allocation table for any newly allocated channels, calls
+ * qcom_smd_create_channel() to create representations of these and add
+ * them to the edge's list of channels.
+ */
+static void qcom_discover_channels(struct qcom_smd_edge *edge)
+{
+ struct qcom_smd_alloc_entry *entry;
+ struct qcom_smd_channel *channel;
+ struct qcom_smd *smd = edge->smd;
+ unsigned long flags;
+ unsigned fifo_id;
+ unsigned info_id;
+ int tbl;
+ int i;
+
+ for (i = 0; i < smd->alloc_tbl_entries; i++) {
+ tbl = i / SMD_ALLOC_TBL_SIZE;
+
+ entry = &smd->alloc_tbl[tbl][i];
+ if (test_bit(i, smd->allocated))
+ continue;
+
+ if (entry->ref_count == 0)
+ continue;
+
+ if (!entry->name[0])
+ continue;
+
+ if (!(entry->flags & SMD_CHANNEL_FLAGS_PACKET))
+ continue;
+
+ if ((entry->flags & SMD_CHANNEL_FLAGS_EDGE_MASK) != edge->edge_id)
+ continue;
+
+ info_id = smem_items[tbl].info_base_id + entry->cid;
+ fifo_id = smem_items[tbl].fifo_base_id + entry->cid;
+
+ channel = qcom_smd_create_channel(edge, info_id, fifo_id, entry->name);
+ if (IS_ERR(channel))
+ continue;
+
+ spin_lock_irqsave(&edge->channels_lock, flags);
+ list_add(&channel->list, &edge->channels);
+ spin_unlock_irqrestore(&edge->channels_lock, flags);
+
+ dev_dbg(smd->dev, "new channel found: '%s'\n", channel->name);
+ set_bit(i, smd->allocated);
+ }
+
+ schedule_work(&edge->work);
+}
+
+/*
+ * This per edge worker scans smem for any new channels and register these. It
+ * then scans all registered channels for state changes that should be handled
+ * by creating or destroying smd client devices for the registered channels.
+ *
+ * LOCKING: edge->channels_lock is not needed to be held during the traversal
+ * of the channels list as it's done synchronously with the only writer.
+ */
+static void qcom_channel_state_worker(struct work_struct *work)
+{
+ struct qcom_smd_channel *channel;
+ struct qcom_smd_edge *edge = container_of(work,
+ struct qcom_smd_edge,
+ work);
+ unsigned remote_state;
+
+ /*
+ * Rescan smem if we have reason to belive that there are new channels.
+ */
+ if (edge->need_rescan) {
+ edge->need_rescan = false;
+ qcom_discover_channels(edge);
+ }
+
+ /*
+ * Register a device for any closed channel where the remote processor
+ * is showing interest in opening the channel.
+ */
+ list_for_each_entry(channel, &edge->channels, list) {
+ if (channel->state != SMD_CHANNEL_CLOSED)
+ continue;
+
+ remote_state = GET_RX_CHANNEL_INFO(channel, state);
+ if (remote_state != SMD_CHANNEL_OPENING &&
+ remote_state != SMD_CHANNEL_OPENED)
+ continue;
+
+ qcom_smd_create_device(channel);
+ }
+
+ /*
+ * Unregister the device for any channel that is opened where the
+ * remote processor is closing the channel.
+ */
+ list_for_each_entry(channel, &edge->channels, list) {
+ if (channel->state != SMD_CHANNEL_OPENING &&
+ channel->state != SMD_CHANNEL_OPENED)
+ continue;
+
+ remote_state = GET_RX_CHANNEL_INFO(channel, state);
+ if (remote_state == SMD_CHANNEL_OPENING ||
+ remote_state == SMD_CHANNEL_OPENED)
+ continue;
+
+ qcom_smd_destroy_device(channel);
+ }
+}
+
+/*
+ * Parses an of_node describing an edge.
+ */
+static int qcom_smd_parse_edge(struct device *dev,
+ struct device_node *node,
+ struct qcom_smd_edge *edge)
+{
+ struct device_node *syscon_np;
+ const char *key;
+ int irq;
+ int ret;
+
+ INIT_LIST_HEAD(&edge->channels);
+ spin_lock_init(&edge->channels_lock);
+
+ INIT_WORK(&edge->work, qcom_channel_state_worker);
+
+ edge->of_node = of_node_get(node);
+
+ irq = irq_of_parse_and_map(node, 0);
+ if (irq < 0) {
+ dev_err(dev, "required smd interrupt missing\n");
+ return -EINVAL;
+ }
+
+ ret = devm_request_irq(dev, irq,
+ qcom_smd_edge_intr, IRQF_TRIGGER_RISING,
+ node->name, edge);
+ if (ret) {
+ dev_err(dev, "failed to request smd irq\n");
+ return ret;
+ }
+
+ edge->irq = irq;
+
+ key = "qcom,smd-edge";
+ ret = of_property_read_u32(node, key, &edge->edge_id);
+ if (ret) {
+ dev_err(dev, "edge missing %s property\n", key);
+ return -EINVAL;
+ }
+
+ syscon_np = of_parse_phandle(node, "qcom,ipc", 0);
+ if (!syscon_np) {
+ dev_err(dev, "no qcom,ipc node\n");
+ return -ENODEV;
+ }
+
+ edge->ipc_regmap = syscon_node_to_regmap(syscon_np);
+ if (IS_ERR(edge->ipc_regmap))
+ return PTR_ERR(edge->ipc_regmap);
+
+ key = "qcom,ipc";
+ ret = of_property_read_u32_index(node, key, 1, &edge->ipc_offset);
+ if (ret < 0) {
+ dev_err(dev, "no offset in %s\n", key);
+ return -EINVAL;
+ }
+
+ ret = of_property_read_u32_index(node, key, 2, &edge->ipc_bit);
+ if (ret < 0) {
+ dev_err(dev, "no bit in %s\n", key);
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int qcom_smd_probe(struct platform_device *pdev)
+{
+ struct qcom_smd_edge *edge;
+ struct device_node *node;
+ struct qcom_smd *smd;
+ size_t array_size;
+ int num_edges;
+ int ret;
+ int i = 0;
+
+ num_edges = of_get_available_child_count(pdev->dev.of_node);
+ array_size = sizeof(*smd) + num_edges * sizeof(struct qcom_smd_edge);
+ smd = devm_kzalloc(&pdev->dev, array_size, GFP_KERNEL);
+ if (!smd)
+ return -ENOMEM;
+ smd->dev = &pdev->dev;
+
+ ret = qcom_smem_get(QCOM_SMEM_HOST_ANY, smem_items[0].alloc_tbl_id,
+ (void **)&smd->alloc_tbl[0], NULL);
+ if (ret < 0) {
+ dev_err(smd->dev, "primary allocation table not available\n");
+ return ret;
+ };
+
+ smd->alloc_tbl_entries = SMD_ALLOC_TBL_SIZE;
+
+ ret = qcom_smem_get(QCOM_SMEM_HOST_ANY, smem_items[1].alloc_tbl_id,
+ (void **)&smd->alloc_tbl[1], NULL);
+ if (ret >= 0)
+ smd->alloc_tbl_entries += SMD_ALLOC_TBL_SIZE;
+
+ smd->num_edges = num_edges;
+ for_each_available_child_of_node(pdev->dev.of_node, node) {
+ edge = &smd->edges[i++];
+ edge->smd = smd;
+
+ ret = qcom_smd_parse_edge(&pdev->dev, node, edge);
+ if (ret)
+ continue;
+
+ edge->need_rescan = true;
+ schedule_work(&edge->work);
+ }
+
+ platform_set_drvdata(pdev, smd);
+
+ return 0;
+}
+
+/*
+ * Shut down all smd clients by making sure that each edge stops processing
+ * events and scanning for new channels, then call destroy on the devices.
+ */
+static int qcom_smd_remove(struct platform_device *pdev)
+{
+ struct qcom_smd_channel *channel;
+ struct qcom_smd_edge *edge;
+ struct qcom_smd *smd = platform_get_drvdata(pdev);
+ int i;
+
+ for (i = 0; i < smd->num_edges; i++) {
+ edge = &smd->edges[i];
+
+ disable_irq(edge->irq);
+ cancel_work_sync(&edge->work);
+
+ list_for_each_entry(channel, &edge->channels, list) {
+ if (!channel->qsdev)
+ continue;
+
+ qcom_smd_destroy_device(channel);
+ }
+ }
+
+ return 0;
+}
+
+static const struct of_device_id qcom_smd_of_match[] = {
+ { .compatible = "qcom,smd" },
+ {}
+};
+MODULE_DEVICE_TABLE(of, qcom_smd_of_match);
+
+static struct platform_driver qcom_smd_driver = {
+ .probe = qcom_smd_probe,
+ .remove = qcom_smd_remove,
+ .driver = {
+ .name = "qcom-smd",
+ .of_match_table = qcom_smd_of_match,
+ },
+};
+
+static int __init qcom_smd_init(void)
+{
+ int ret;
+
+ ret = bus_register(&qcom_smd_bus);
+ if (ret) {
+ pr_err("failed to register smd bus: %d\n", ret);
+ return ret;
+ }
+
+ return platform_driver_register(&qcom_smd_driver);
+}
+arch_initcall(qcom_smd_init);
+
+static void __exit qcom_smd_exit(void)
+{
+ platform_driver_unregister(&qcom_smd_driver);
+ bus_unregister(&qcom_smd_bus);
+}
+module_exit(qcom_smd_exit);
+
+MODULE_AUTHOR("Bjorn Andersson <bjorn.andersson@sonymobile.com>");
+MODULE_DESCRIPTION("Qualcomm Shared Memory Driver");
+MODULE_LICENSE("GPL v2");
diff --git a/include/linux/soc/qcom/smd.h b/include/linux/soc/qcom/smd.h
new file mode 100644
index 0000000..22cf3bf
--- /dev/null
+++ b/include/linux/soc/qcom/smd.h
@@ -0,0 +1,46 @@
+#ifndef __LINUX_QCOM_SMEM_H__
+#define __LINUX_QCOM_SMEM_H__
+
+#include <linux/device.h>
+#include <linux/mod_devicetable.h>
+
+struct qcom_smd;
+struct qcom_smd_channel;
+struct qcom_smd_lookup;
+
+/**
+ * struct qcom_smd_device - smd device struct
+ * @dev: the device struct
+ * @channel: handle to the smd channel for this device
+ */
+struct qcom_smd_device {
+ struct device dev;
+ struct qcom_smd_channel *channel;
+};
+
+/**
+ * struct qcom_smd_driver - smd driver struct
+ * @driver: underlying device driver
+ * @probe: invoked when the smd channel is found
+ * @remove: invoked when the smd channel is closed
+ * @callback: invoked when an inbound message is received on the channel,
+ * should return 0 on success or -EBUSY if the data cannot be
+ * consumed at this time
+ */
+struct qcom_smd_driver {
+ struct device_driver driver;
+ int (*probe)(struct qcom_smd_device *dev);
+ void (*remove)(struct qcom_smd_device *dev);
+ int (*callback)(struct qcom_smd_device *, const void *, size_t);
+};
+
+int qcom_smd_driver_register(struct qcom_smd_driver *drv);
+void qcom_smd_driver_unregister(struct qcom_smd_driver *drv);
+
+#define module_qcom_smd_driver(__smd_driver) \
+ module_driver(__smd_driver, qcom_smd_driver_register, \
+ qcom_smd_driver_unregister)
+
+int qcom_smd_send(struct qcom_smd_channel *channel, const void *data, int len);
+
+#endif
--
1.9.3 (Apple Git-50)
^ permalink raw reply related [flat|nested] 39+ messages in thread* Re: [PATCH v2 04/11] soc: qcom: Add Shared Memory Driver
2015-06-26 21:50 ` [PATCH v2 04/11] soc: qcom: Add Shared Memory Driver bjorn
@ 2015-07-07 13:45 ` Georgi Djakov
2015-07-13 22:27 ` Bjorn Andersson
0 siblings, 1 reply; 39+ messages in thread
From: Georgi Djakov @ 2015-07-07 13:45 UTC (permalink / raw)
To: bjorn, Kumar Gala, Andy Gross, David Brown
Cc: linux-kernel, linux-soc, Jeffrey Hugo, linux-arm-msm
Hi Bjorn,
Thank you for this patchset! Some nits and a question below.
On 06/27/2015 12:50 AM, bjorn@kryo.se wrote:
> From: Bjorn Andersson <bjorn.andersson@sonymobile.com>
>
> This adds the Qualcomm Shared Memory Driver (SMD) providing
> communication channels to remote processors, ontop of SMEM.
>
> Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
> ---
> drivers/soc/qcom/Kconfig | 8 +
> drivers/soc/qcom/Makefile | 1 +
> drivers/soc/qcom/smd.c | 1324 ++++++++++++++++++++++++++++++++++++++++++
> include/linux/soc/qcom/smd.h | 46 ++
> 4 files changed, 1379 insertions(+)
> create mode 100644 drivers/soc/qcom/smd.c
> create mode 100644 include/linux/soc/qcom/smd.h
>
[...]
> --- /dev/null
> +++ b/drivers/soc/qcom/smd.c
> @@ -0,0 +1,1324 @@
> +/*
> + * Copyright (c) 2015, Sony Mobile Communications AB.
> + * Copyright (c) 2012-2013, The Linux Foundation. All rights reserved.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 and
> + * only version 2 as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/delay.h>
unused?
[...]
> +
> +#define GET_RX_CHANNEL_INFO(channel, param) \
> + (channel->rx_info_word ? \
> + channel->rx_info_word->param : \
> + channel->rx_info->param)
> +
> +#define SET_RX_CHANNEL_INFO(channel, param, value) \
> + (channel->rx_info_word ? \
> + (channel->rx_info_word->param = value) : \
> + (channel->rx_info->param = value))
> +
> +#define GET_TX_CHANNEL_INFO(channel, param) \
> + (channel->rx_info_word ? \
Maybe this should be tx_info_word?
> + channel->tx_info_word->param : \
> + channel->tx_info->param)
> +
> +#define SET_TX_CHANNEL_INFO(channel, param, value) \
> + (channel->rx_info_word ? \
ditto?
> + (channel->tx_info_word->param = value) : \
> + (channel->tx_info->param = value))
> +
[...]
> + ret = qcom_smem_get(edge->edge_id, smem_fifo_item, &fifo_base, &fifo_size);
> + if (ret)
> + goto free_name_and_channel;
> +
> + /* The channel consist of a rx and tx fifo of equal size */
> + fifo_size /= 2;
> +
> + dev_dbg(smd->dev, "new channel '%s' info-size: %d fifo-size: %zu\n",
%zu for info-size?
> + name, info_size, fifo_size);
> +
[...]
> +static int __init qcom_smd_init(void)
> +{
> + int ret;
> +
> + ret = bus_register(&qcom_smd_bus);
> + if (ret) {
> + pr_err("failed to register smd bus: %d\n", ret);
> + return ret;
> + }
> +
> + return platform_driver_register(&qcom_smd_driver);
> +}
> +arch_initcall(qcom_smd_init);
> +
> +static void __exit qcom_smd_exit(void)
> +{
> + platform_driver_unregister(&qcom_smd_driver);
> + bus_unregister(&qcom_smd_bus);
> +}
> +module_exit(qcom_smd_exit);
> +
[...]
> +/**
> + * struct qcom_smd_driver - smd driver struct
> + * @driver: underlying device driver
> + * @probe: invoked when the smd channel is found
> + * @remove: invoked when the smd channel is closed
> + * @callback: invoked when an inbound message is received on the channel,
> + * should return 0 on success or -EBUSY if the data cannot be
> + * consumed at this time
> + */
> +struct qcom_smd_driver {
> + struct device_driver driver;
> + int (*probe)(struct qcom_smd_device *dev);
> + void (*remove)(struct qcom_smd_device *dev);
> + int (*callback)(struct qcom_smd_device *, const void *, size_t);
> +};
> +
> +int qcom_smd_driver_register(struct qcom_smd_driver *drv);
> +void qcom_smd_driver_unregister(struct qcom_smd_driver *drv);
> +
> +#define module_qcom_smd_driver(__smd_driver) \
> + module_driver(__smd_driver, qcom_smd_driver_register, \
> + qcom_smd_driver_unregister)
> +
This comment is mostly related to your RPM over SMD driver patch, as
i have a RPM clock driver based on it. The RPM clock driver registers
some fundamental stuff like XO and i had to hack smd-rpm to probe
earlier, so that most other drivers can initialize. So i was wondering,
what if we register the drivers on the bus earlier? What do you think?
Thanks,
Georgi
^ permalink raw reply [flat|nested] 39+ messages in thread* Re: [PATCH v2 04/11] soc: qcom: Add Shared Memory Driver
2015-07-07 13:45 ` Georgi Djakov
@ 2015-07-13 22:27 ` Bjorn Andersson
2015-07-21 11:46 ` Georgi Djakov
0 siblings, 1 reply; 39+ messages in thread
From: Bjorn Andersson @ 2015-07-13 22:27 UTC (permalink / raw)
To: Georgi Djakov
Cc: bjorn, Kumar Gala, Andy Gross, David Brown, linux-kernel,
linux-soc, Jeffrey Hugo, linux-arm-msm
On Tue 07 Jul 06:45 PDT 2015, Georgi Djakov wrote:
> Hi Bjorn,
> Thank you for this patchset! Some nits and a question below.
>
Thank you!
> On 06/27/2015 12:50 AM, bjorn@kryo.se wrote:
> > From: Bjorn Andersson <bjorn.andersson@sonymobile.com>
> >
> > This adds the Qualcomm Shared Memory Driver (SMD) providing
> > communication channels to remote processors, ontop of SMEM.
> >
> > Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
> > ---
> > drivers/soc/qcom/Kconfig | 8 +
> > drivers/soc/qcom/Makefile | 1 +
> > drivers/soc/qcom/smd.c | 1324 ++++++++++++++++++++++++++++++++++++++++++
> > include/linux/soc/qcom/smd.h | 46 ++
> > 4 files changed, 1379 insertions(+)
> > create mode 100644 drivers/soc/qcom/smd.c
> > create mode 100644 include/linux/soc/qcom/smd.h
> >
> [...]
> > --- /dev/null
> > +++ b/drivers/soc/qcom/smd.c
> > @@ -0,0 +1,1324 @@
> > +/*
> > + * Copyright (c) 2015, Sony Mobile Communications AB.
> > + * Copyright (c) 2012-2013, The Linux Foundation. All rights reserved.
> > + *
> > + * This program is free software; you can redistribute it and/or modify
> > + * it under the terms of the GNU General Public License version 2 and
> > + * only version 2 as published by the Free Software Foundation.
> > + *
> > + * This program is distributed in the hope that it will be useful,
> > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> > + * GNU General Public License for more details.
> > + */
> > +
> > +#include <linux/delay.h>
>
> unused?
>
Right, used to just delay on the tx buffer being full, will drop.
> [...]
> > +
> > +#define GET_RX_CHANNEL_INFO(channel, param) \
> > + (channel->rx_info_word ? \
> > + channel->rx_info_word->param : \
> > + channel->rx_info->param)
> > +
> > +#define SET_RX_CHANNEL_INFO(channel, param, value) \
> > + (channel->rx_info_word ? \
> > + (channel->rx_info_word->param = value) : \
> > + (channel->rx_info->param = value))
> > +
> > +#define GET_TX_CHANNEL_INFO(channel, param) \
> > + (channel->rx_info_word ? \
>
> Maybe this should be tx_info_word?
>
There's no practical difference, but I'll update it.
> > + channel->tx_info_word->param : \
> > + channel->tx_info->param)
> > +
> > +#define SET_TX_CHANNEL_INFO(channel, param, value) \
> > + (channel->rx_info_word ? \
>
> ditto?
>
ditto...
> > + (channel->tx_info_word->param = value) : \
> > + (channel->tx_info->param = value))
> > +
> [...]
> > + ret = qcom_smem_get(edge->edge_id, smem_fifo_item, &fifo_base, &fifo_size);
> > + if (ret)
> > + goto free_name_and_channel;
> > +
> > + /* The channel consist of a rx and tx fifo of equal size */
> > + fifo_size /= 2;
> > +
> > + dev_dbg(smd->dev, "new channel '%s' info-size: %d fifo-size: %zu\n",
>
> %zu for info-size?
>
Hmm, the compiler only complained about the fifo_size, but you're of
course right.
> > + name, info_size, fifo_size);
> > +
>
> [...]
> > +static int __init qcom_smd_init(void)
> > +{
> > + int ret;
> > +
> > + ret = bus_register(&qcom_smd_bus);
> > + if (ret) {
> > + pr_err("failed to register smd bus: %d\n", ret);
> > + return ret;
> > + }
> > +
> > + return platform_driver_register(&qcom_smd_driver);
> > +}
> > +arch_initcall(qcom_smd_init);
> > +
> > +static void __exit qcom_smd_exit(void)
> > +{
> > + platform_driver_unregister(&qcom_smd_driver);
> > + bus_unregister(&qcom_smd_bus);
> > +}
> > +module_exit(qcom_smd_exit);
> > +
> [...]
> > +/**
> > + * struct qcom_smd_driver - smd driver struct
> > + * @driver: underlying device driver
> > + * @probe: invoked when the smd channel is found
> > + * @remove: invoked when the smd channel is closed
> > + * @callback: invoked when an inbound message is received on the channel,
> > + * should return 0 on success or -EBUSY if the data cannot be
> > + * consumed at this time
> > + */
> > +struct qcom_smd_driver {
> > + struct device_driver driver;
> > + int (*probe)(struct qcom_smd_device *dev);
> > + void (*remove)(struct qcom_smd_device *dev);
> > + int (*callback)(struct qcom_smd_device *, const void *, size_t);
> > +};
> > +
> > +int qcom_smd_driver_register(struct qcom_smd_driver *drv);
> > +void qcom_smd_driver_unregister(struct qcom_smd_driver *drv);
> > +
> > +#define module_qcom_smd_driver(__smd_driver) \
> > + module_driver(__smd_driver, qcom_smd_driver_register, \
> > + qcom_smd_driver_unregister)
> > +
>
> This comment is mostly related to your RPM over SMD driver patch, as
> i have a RPM clock driver based on it. The RPM clock driver registers
> some fundamental stuff like XO and i had to hack smd-rpm to probe
> earlier, so that most other drivers can initialize. So i was wondering,
> what if we register the drivers on the bus earlier? What do you think?
>
My only concern would be that if we're calling
qcom_smd_driver_register() before the smd arch_initcall has registered
the bus it will fail.
Part of this I see no problem with modifying the rpm driver to register
earlier - and it would be good to have those regulators earlier as
well...
I've intentionally not done anything about this, because it's helped to
smoke out a bunch of EPROBE_DEFER issues for me already, but longer term
it's not okay for all our drivers to fail 2-3 times before the
regulators are up...
Regards,
Bjorn
^ permalink raw reply [flat|nested] 39+ messages in thread* Re: [PATCH v2 04/11] soc: qcom: Add Shared Memory Driver
2015-07-13 22:27 ` Bjorn Andersson
@ 2015-07-21 11:46 ` Georgi Djakov
0 siblings, 0 replies; 39+ messages in thread
From: Georgi Djakov @ 2015-07-21 11:46 UTC (permalink / raw)
To: Bjorn Andersson
Cc: bjorn, Kumar Gala, Andy Gross, David Brown, linux-kernel,
linux-soc, Jeffrey Hugo, linux-arm-msm
On 07/14/2015 01:27 AM, Bjorn Andersson wrote:
> On Tue 07 Jul 06:45 PDT 2015, Georgi Djakov wrote:
>
>> Hi Bjorn,
>> Thank you for this patchset! Some nits and a question below.
>>
>
> Thank you!
>
>> On 06/27/2015 12:50 AM, bjorn@kryo.se wrote:
>>> From: Bjorn Andersson <bjorn.andersson@sonymobile.com>
>>>
>>> This adds the Qualcomm Shared Memory Driver (SMD) providing
>>> communication channels to remote processors, ontop of SMEM.
>>>
>>> Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
[..]
>> [...]
>>> +static int __init qcom_smd_init(void)
>>> +{
>>> + int ret;
>>> +
>>> + ret = bus_register(&qcom_smd_bus);
>>> + if (ret) {
>>> + pr_err("failed to register smd bus: %d\n", ret);
>>> + return ret;
>>> + }
>>> +
>>> + return platform_driver_register(&qcom_smd_driver);
>>> +}
>>> +arch_initcall(qcom_smd_init);
>>> +
>>> +static void __exit qcom_smd_exit(void)
>>> +{
>>> + platform_driver_unregister(&qcom_smd_driver);
>>> + bus_unregister(&qcom_smd_bus);
>>> +}
>>> +module_exit(qcom_smd_exit);
>>> +
>> [...]
>>> +/**
>>> + * struct qcom_smd_driver - smd driver struct
>>> + * @driver: underlying device driver
>>> + * @probe: invoked when the smd channel is found
>>> + * @remove: invoked when the smd channel is closed
>>> + * @callback: invoked when an inbound message is received on the channel,
>>> + * should return 0 on success or -EBUSY if the data cannot be
>>> + * consumed at this time
>>> + */
>>> +struct qcom_smd_driver {
>>> + struct device_driver driver;
>>> + int (*probe)(struct qcom_smd_device *dev);
>>> + void (*remove)(struct qcom_smd_device *dev);
>>> + int (*callback)(struct qcom_smd_device *, const void *, size_t);
>>> +};
>>> +
>>> +int qcom_smd_driver_register(struct qcom_smd_driver *drv);
>>> +void qcom_smd_driver_unregister(struct qcom_smd_driver *drv);
>>> +
>>> +#define module_qcom_smd_driver(__smd_driver) \
>>> + module_driver(__smd_driver, qcom_smd_driver_register, \
>>> + qcom_smd_driver_unregister)
>>> +
>>
>> This comment is mostly related to your RPM over SMD driver patch, as
>> i have a RPM clock driver based on it. The RPM clock driver registers
>> some fundamental stuff like XO and i had to hack smd-rpm to probe
>> earlier, so that most other drivers can initialize. So i was wondering,
>> what if we register the drivers on the bus earlier? What do you think?
>>
>
> My only concern would be that if we're calling
> qcom_smd_driver_register() before the smd arch_initcall has registered
> the bus it will fail.
>
Maybe we can use core/postcore_initcall for smd, and then arch_initcall
for smd-rpm?
> Part of this I see no problem with modifying the rpm driver to register
> earlier - and it would be good to have those regulators earlier as
> well...
Booting with initcall_debug shows me that most busses are registered at
postcore_initcall - like spmi, i2c, spi etc.
> I've intentionally not done anything about this, because it's helped to
> smoke out a bunch of EPROBE_DEFER issues for me already, but longer term
> it's not okay for all our drivers to fail 2-3 times before the
> regulators are up...
I agree. Thanks!
BR,
Georgi
^ permalink raw reply [flat|nested] 39+ messages in thread
* [PATCH v2 05/11] mfd: devicetree: bindings: Add Qualcomm SMD based RPM DT binding
2015-06-26 21:50 [PATCH v2 00/11] Qualcomm Shared Memory & RPM drivers bjorn
` (3 preceding siblings ...)
2015-06-26 21:50 ` [PATCH v2 04/11] soc: qcom: Add Shared Memory Driver bjorn
@ 2015-06-26 21:50 ` bjorn
2015-07-07 12:16 ` Lee Jones
2015-06-26 21:50 ` [PATCH v2 06/11] mfd: qcom-smd-rpm: Driver for the Qualcomm RPM over SMD bjorn
` (5 subsequent siblings)
10 siblings, 1 reply; 39+ messages in thread
From: bjorn @ 2015-06-26 21:50 UTC (permalink / raw)
To: Andy Gross, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell,
Kumar Gala, Lee Jones, Samuel Ortiz
Cc: devicetree, Mark Brown, linux-kernel, linux-arm-msm
From: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Add binding documentation for the Qualcomm Resource Power Manager (RPM)
using shared memory (Qualcomm SMD) as transport mechanism. This is found
in 8974 and newer based devices.
The binding currently describes the rpm itself and the regulator
subnodes.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
---
.../devicetree/bindings/mfd/qcom-rpm-smd.txt | 117 +++++++++++++++++++++
include/dt-bindings/mfd/qcom-smd-rpm.h | 28 +++++
2 files changed, 145 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/qcom-rpm-smd.txt
create mode 100644 include/dt-bindings/mfd/qcom-smd-rpm.h
diff --git a/Documentation/devicetree/bindings/mfd/qcom-rpm-smd.txt b/Documentation/devicetree/bindings/mfd/qcom-rpm-smd.txt
new file mode 100644
index 0000000..e27f5c4
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/qcom-rpm-smd.txt
@@ -0,0 +1,117 @@
+Qualcomm Resource Power Manager (RPM) over SMD
+
+This driver is used to interface with the Resource Power Manager (RPM) found in
+various Qualcomm platforms. The RPM allows each component in the system to vote
+for state of the system resources, such as clocks, regulators and bus
+frequencies.
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: must be one of:
+ "qcom,rpm-msm8974"
+
+- qcom,smd-channels:
+ Usage: required
+ Value type: <stringlist>
+ Definition: Shared Memory channel used for communication with the RPM
+
+= SUBDEVICES
+
+The RPM exposes resources to its subnodes. The below bindings specify the set
+of valid subnodes that can operate on these resources.
+
+== Regulators
+
+Regulator nodes are identified by their compatible:
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: must be one of:
+ "qcom,rpm-pm8841-regulators"
+ "qcom,rpm-pm8941-regulators"
+
+- vdd_s1-supply:
+- vdd_s2-supply:
+- vdd_s3-supply:
+- vdd_s4-supply:
+- vdd_s5-supply:
+- vdd_s6-supply:
+- vdd_s7-supply:
+- vdd_s8-supply:
+ Usage: optional (pm8841 only)
+ Value type: <phandle>
+ Definition: reference to regulator supplying the input pin, as
+ described in the data sheet
+
+- vdd_s1-supply:
+- vdd_s2-supply:
+- vdd_s3-supply:
+- vdd_l1_l3-supply:
+- vdd_l2_lvs1_2_3-supply:
+- vdd_l4_l11-supply:
+- vdd_l5_l7-supply:
+- vdd_l6_l12_l14_l15-supply:
+- vdd_l8_l16_l18_l19-supply:
+- vdd_l9_l10_l17_l22-supply:
+- vdd_l13_l20_l23_l24-supply:
+- vdd_l21-supply:
+- vin_5vs-supply:
+ Usage: optional (pm8941 only)
+ Value type: <phandle>
+ Definition: reference to regulator supplying the input pin, as
+ described in the data sheet
+
+The regulator node houses sub-nodes for each regulator within the device. Each
+sub-node is identified using the node's name, with valid values listed for each
+of the pmics below.
+
+pm8841:
+ s1, s2, s3, s4, s5, s6, s7, s8
+
+pm8941:
+ s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13,
+ l14, l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2,
+ lvs3, 5vs1, 5vs2
+
+The content of each sub-node is defined by the standard binding for regulators -
+see regulator.txt.
+
+= EXAMPLE
+
+ smd {
+ compatible = "qcom,smd";
+
+ rpm {
+ interrupts = <0 168 1>;
+ qcom,ipc = <&apcs 8 0>;
+ qcom,smd-edge = <15>;
+
+ rpm_requests {
+ compatible = "qcom,rpm-msm8974";
+ qcom,smd-channels = "rpm_requests";
+
+ pm8941-regulators {
+ compatible = "qcom,rpm-pm8941-regulators";
+ vdd_l13_l20_l23_l24-supply = <&pm8941_boost>;
+
+ pm8941_s3: s3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pm8941_boost: s4 {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ pm8941_l20: l20 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ };
+ };
+ };
+ };
+ };
+
diff --git a/include/dt-bindings/mfd/qcom-smd-rpm.h b/include/dt-bindings/mfd/qcom-smd-rpm.h
new file mode 100644
index 0000000..890ca52
--- /dev/null
+++ b/include/dt-bindings/mfd/qcom-smd-rpm.h
@@ -0,0 +1,28 @@
+/*
+ * This header provides constants for the Qualcomm RPM bindings.
+ */
+
+#ifndef _DT_BINDINGS_MFD_QCOM_SMD_RPM_H
+#define _DT_BINDINGS_MFD_QCOM_SMD_RPM_H
+
+/*
+ * Constants used for addressing resources in the RPM.
+ */
+#define QCOM_SMD_RPM_BUS_CLK 0x316b6c63
+#define QCOM_SMD_RPM_BUS_MASTER 0x73616d62
+#define QCOM_SMD_RPM_BUS_SLAVE 0x766c7362
+#define QCOM_SMD_RPM_CLK_BUF_A 0x616B6C63
+#define QCOM_SMD_RPM_LDOA 0x616f646c
+#define QCOM_SMD_RPM_LDOB 0x626F646C
+#define QCOM_SMD_RPM_MEM_CLK 0x326b6c63
+#define QCOM_SMD_RPM_MISC_CLK 0x306b6c63
+#define QCOM_SMD_RPM_NCPA 0x6170636E
+#define QCOM_SMD_RPM_NCPB 0x6270636E
+#define QCOM_SMD_RPM_OCMEM_PWR 0x706d636f
+#define QCOM_SMD_RPM_QPIC_CLK 0x63697071
+#define QCOM_SMD_RPM_SMPA 0x61706d73
+#define QCOM_SMD_RPM_SMPB 0x62706d73
+#define QCOM_SMD_RPM_SPDM 0x63707362
+#define QCOM_SMD_RPM_VSA 0x00617376
+
+#endif
--
1.9.3 (Apple Git-50)
^ permalink raw reply related [flat|nested] 39+ messages in thread* Re: [PATCH v2 05/11] mfd: devicetree: bindings: Add Qualcomm SMD based RPM DT binding
2015-06-26 21:50 ` [PATCH v2 05/11] mfd: devicetree: bindings: Add Qualcomm SMD based RPM DT binding bjorn
@ 2015-07-07 12:16 ` Lee Jones
2015-07-13 21:48 ` Bjorn Andersson
0 siblings, 1 reply; 39+ messages in thread
From: Lee Jones @ 2015-07-07 12:16 UTC (permalink / raw)
To: bjorn
Cc: Andy Gross, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell,
Kumar Gala, Samuel Ortiz, devicetree, Mark Brown, linux-kernel,
linux-arm-msm
FAO Mark and DT chaps,
> From: Bjorn Andersson <bjorn.andersson@sonymobile.com>
>
> Add binding documentation for the Qualcomm Resource Power Manager (RPM)
> using shared memory (Qualcomm SMD) as transport mechanism. This is found
> in 8974 and newer based devices.
>
> The binding currently describes the rpm itself and the regulator
> subnodes.
>
> Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
> ---
> .../devicetree/bindings/mfd/qcom-rpm-smd.txt | 117 +++++++++++++++++++++
> include/dt-bindings/mfd/qcom-smd-rpm.h | 28 +++++
> 2 files changed, 145 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mfd/qcom-rpm-smd.txt
> create mode 100644 include/dt-bindings/mfd/qcom-smd-rpm.h
>
> diff --git a/Documentation/devicetree/bindings/mfd/qcom-rpm-smd.txt b/Documentation/devicetree/bindings/mfd/qcom-rpm-smd.txt
> new file mode 100644
> index 0000000..e27f5c4
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/qcom-rpm-smd.txt
> @@ -0,0 +1,117 @@
> +Qualcomm Resource Power Manager (RPM) over SMD
> +
> +This driver is used to interface with the Resource Power Manager (RPM) found in
> +various Qualcomm platforms. The RPM allows each component in the system to vote
> +for state of the system resources, such as clocks, regulators and bus
> +frequencies.
> +
> +- compatible:
> + Usage: required
> + Value type: <string>
> + Definition: must be one of:
> + "qcom,rpm-msm8974"
> +
> +- qcom,smd-channels:
> + Usage: required
> + Value type: <stringlist>
> + Definition: Shared Memory channel used for communication with the RPM
This is going to require a DT Ack.
Also, I don't see it being used anywhere.
> += SUBDEVICES
> +
> +The RPM exposes resources to its subnodes. The below bindings specify the set
> +of valid subnodes that can operate on these resources.
> +
> +== Regulators
> +
> +Regulator nodes are identified by their compatible:
> +
> +- compatible:
> + Usage: required
> + Value type: <string>
> + Definition: must be one of:
> + "qcom,rpm-pm8841-regulators"
> + "qcom,rpm-pm8941-regulators"
> +
> +- vdd_s1-supply:
> +- vdd_s2-supply:
> +- vdd_s3-supply:
> +- vdd_s4-supply:
> +- vdd_s5-supply:
> +- vdd_s6-supply:
> +- vdd_s7-supply:
> +- vdd_s8-supply:
> + Usage: optional (pm8841 only)
> + Value type: <phandle>
> + Definition: reference to regulator supplying the input pin, as
> + described in the data sheet
> +
> +- vdd_s1-supply:
> +- vdd_s2-supply:
> +- vdd_s3-supply:
> +- vdd_l1_l3-supply:
> +- vdd_l2_lvs1_2_3-supply:
> +- vdd_l4_l11-supply:
> +- vdd_l5_l7-supply:
> +- vdd_l6_l12_l14_l15-supply:
> +- vdd_l8_l16_l18_l19-supply:
> +- vdd_l9_l10_l17_l22-supply:
> +- vdd_l13_l20_l23_l24-supply:
> +- vdd_l21-supply:
> +- vin_5vs-supply:
> + Usage: optional (pm8941 only)
> + Value type: <phandle>
> + Definition: reference to regulator supplying the input pin, as
> + described in the data sheet
> +
> +The regulator node houses sub-nodes for each regulator within the device. Each
> +sub-node is identified using the node's name, with valid values listed for each
> +of the pmics below.
> +
> +pm8841:
> + s1, s2, s3, s4, s5, s6, s7, s8
> +
> +pm8941:
> + s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13,
> + l14, l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2,
> + lvs3, 5vs1, 5vs2
> +
> +The content of each sub-node is defined by the standard binding for regulators -
> +see regulator.txt.
s-regulator.txt-../regulator/regulator.txt-
> +
> += EXAMPLE
> +
> + smd {
> + compatible = "qcom,smd";
Is an SMD (Shared Memory Device?) real hardware?
> + rpm {
> + interrupts = <0 168 1>;
> + qcom,ipc = <&apcs 8 0>;
> + qcom,smd-edge = <15>;
The child node won't probe without a compatible string. Shouldn't
"qcom,rpm-msm8974" be in here instead?
> + rpm_requests {
This node appears to be undocumented.
Does it represent real h/w?
> + compatible = "qcom,rpm-msm8974";
> + qcom,smd-channels = "rpm_requests";
> +
> + pm8941-regulators {
> + compatible = "qcom,rpm-pm8941-regulators";
> + vdd_l13_l20_l23_l24-supply = <&pm8941_boost>;
I'd like Mark to glance at this.
> + pm8941_s3: s3 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
Aren't these fixed regulators?
> + };
> +
> + pm8941_boost: s4 {
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + };
> +
> + pm8941_l20: l20 {
> + regulator-min-microvolt = <2950000>;
> + regulator-max-microvolt = <2950000>;
> + };
> + };
> + };
> + };
> + };
> +
> diff --git a/include/dt-bindings/mfd/qcom-smd-rpm.h b/include/dt-bindings/mfd/qcom-smd-rpm.h
> new file mode 100644
> index 0000000..890ca52
> --- /dev/null
> +++ b/include/dt-bindings/mfd/qcom-smd-rpm.h
> @@ -0,0 +1,28 @@
> +/*
> + * This header provides constants for the Qualcomm RPM bindings.
> + */
> +
> +#ifndef _DT_BINDINGS_MFD_QCOM_SMD_RPM_H
> +#define _DT_BINDINGS_MFD_QCOM_SMD_RPM_H
> +
> +/*
> + * Constants used for addressing resources in the RPM.
> + */
> +#define QCOM_SMD_RPM_BUS_CLK 0x316b6c63
> +#define QCOM_SMD_RPM_BUS_MASTER 0x73616d62
> +#define QCOM_SMD_RPM_BUS_SLAVE 0x766c7362
> +#define QCOM_SMD_RPM_CLK_BUF_A 0x616B6C63
> +#define QCOM_SMD_RPM_LDOA 0x616f646c
> +#define QCOM_SMD_RPM_LDOB 0x626F646C
> +#define QCOM_SMD_RPM_MEM_CLK 0x326b6c63
> +#define QCOM_SMD_RPM_MISC_CLK 0x306b6c63
> +#define QCOM_SMD_RPM_NCPA 0x6170636E
> +#define QCOM_SMD_RPM_NCPB 0x6270636E
> +#define QCOM_SMD_RPM_OCMEM_PWR 0x706d636f
> +#define QCOM_SMD_RPM_QPIC_CLK 0x63697071
> +#define QCOM_SMD_RPM_SMPA 0x61706d73
> +#define QCOM_SMD_RPM_SMPB 0x62706d73
> +#define QCOM_SMD_RPM_SPDM 0x63707362
> +#define QCOM_SMD_RPM_VSA 0x00617376
> +
> +#endif
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 39+ messages in thread* Re: [PATCH v2 05/11] mfd: devicetree: bindings: Add Qualcomm SMD based RPM DT binding
2015-07-07 12:16 ` Lee Jones
@ 2015-07-13 21:48 ` Bjorn Andersson
2015-07-23 13:31 ` Lee Jones
0 siblings, 1 reply; 39+ messages in thread
From: Bjorn Andersson @ 2015-07-13 21:48 UTC (permalink / raw)
To: Lee Jones
Cc: bjorn, Andy Gross, Rob Herring, Pawel Moll, Mark Rutland,
Ian Campbell, Kumar Gala, Samuel Ortiz, devicetree, Mark Brown,
linux-kernel, linux-arm-msm
On Tue 07 Jul 05:16 PDT 2015, Lee Jones wrote:
> FAO Mark and DT chaps,
>
> > From: Bjorn Andersson <bjorn.andersson@sonymobile.com>
> >
> > Add binding documentation for the Qualcomm Resource Power Manager (RPM)
> > using shared memory (Qualcomm SMD) as transport mechanism. This is found
> > in 8974 and newer based devices.
> >
> > The binding currently describes the rpm itself and the regulator
> > subnodes.
> >
> > Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
> > ---
> > .../devicetree/bindings/mfd/qcom-rpm-smd.txt | 117 +++++++++++++++++++++
> > include/dt-bindings/mfd/qcom-smd-rpm.h | 28 +++++
> > 2 files changed, 145 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/mfd/qcom-rpm-smd.txt
> > create mode 100644 include/dt-bindings/mfd/qcom-smd-rpm.h
> >
> > diff --git a/Documentation/devicetree/bindings/mfd/qcom-rpm-smd.txt b/Documentation/devicetree/bindings/mfd/qcom-rpm-smd.txt
[..]
> > +- qcom,smd-channels:
> > + Usage: required
> > + Value type: <stringlist>
> > + Definition: Shared Memory channel used for communication with the RPM
>
> This is going to require a DT Ack.
>
> Also, I don't see it being used anywhere.
>
It's a common property of all smd devices, defining the smd channel this
driver should bind to.
> > += SUBDEVICES
> > +
> > +The RPM exposes resources to its subnodes. The below bindings specify the set
> > +of valid subnodes that can operate on these resources.
> > +
> > +== Regulators
> > +
[..]
> > +The content of each sub-node is defined by the standard binding for regulators -
> > +see regulator.txt.
>
> s-regulator.txt-../regulator/regulator.txt-
>
Right.
> > +
> > += EXAMPLE
> > +
> > + smd {
> > + compatible = "qcom,smd";
>
> Is an SMD (Shared Memory Device?) real hardware?
>
SMD is a mechanism for using shared memory for point-to-point
communication channels with remote processors in all Qualcomm platforms.
So it's not hardware, it's the control mechanism for communicating with
real hardware.
> > + rpm {
> > + interrupts = <0 168 1>;
> > + qcom,ipc = <&apcs 8 0>;
> > + qcom,smd-edge = <15>;
>
> The child node won't probe without a compatible string. Shouldn't
> "qcom,rpm-msm8974" be in here instead?
>
These sub-nodes represents a logical grouping of the various channels
that exist to this remote processor. For the rpm there is only the
"rpm_requests" channel - used for sending regulator & clock requests.
> > + rpm_requests {
>
> This node appears to be undocumented.
>
This is the actual rpm device node, the smd & rpm nodes above are
included for completeness of the example.
They should perhaps be dropped to make this clearer.
> Does it represent real h/w?
>
The other end of this smd channel is a micro controller that handles
regulator and clock requests for the platform - so this is hardware.
This is equivalent to the qcom_rpm driver, but instead of a hardware
like register window this uses the same packet based messaging mechanism
that's used for other remote peripherals in the Qualcomm platform.
> > + compatible = "qcom,rpm-msm8974";
> > + qcom,smd-channels = "rpm_requests";
> > +
> > + pm8941-regulators {
> > + compatible = "qcom,rpm-pm8941-regulators";
> > + vdd_l13_l20_l23_l24-supply = <&pm8941_boost>;
>
> I'd like Mark to glance at this.
>
Right.
> > + pm8941_s3: s3 {
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1800000>;
>
> Aren't these fixed regulators?
>
In this system configuration most of the regulators have fixed values,
but the regulators (hw) are not fixed.
> > + };
> > +
> > + pm8941_boost: s4 {
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + };
> > +
> > + pm8941_l20: l20 {
> > + regulator-min-microvolt = <2950000>;
> > + regulator-max-microvolt = <2950000>;
> > + };
> > + };
> > + };
> > + };
> > + };
> > +
Thanks,
Bjorn
^ permalink raw reply [flat|nested] 39+ messages in thread* Re: [PATCH v2 05/11] mfd: devicetree: bindings: Add Qualcomm SMD based RPM DT binding
2015-07-13 21:48 ` Bjorn Andersson
@ 2015-07-23 13:31 ` Lee Jones
2015-07-23 16:41 ` Bjorn Andersson
0 siblings, 1 reply; 39+ messages in thread
From: Lee Jones @ 2015-07-23 13:31 UTC (permalink / raw)
To: Bjorn Andersson
Cc: bjorn, Andy Gross, Rob Herring, Pawel Moll, Mark Rutland,
Ian Campbell, Kumar Gala, Samuel Ortiz, devicetree, Mark Brown,
linux-kernel, linux-arm-msm
On Mon, 13 Jul 2015, Bjorn Andersson wrote:
> On Tue 07 Jul 05:16 PDT 2015, Lee Jones wrote:
>
> > FAO Mark and DT chaps,
> >
> > > From: Bjorn Andersson <bjorn.andersson@sonymobile.com>
> > >
> > > Add binding documentation for the Qualcomm Resource Power Manager (RPM)
> > > using shared memory (Qualcomm SMD) as transport mechanism. This is found
> > > in 8974 and newer based devices.
> > >
> > > The binding currently describes the rpm itself and the regulator
> > > subnodes.
> > >
> > > Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
> > > ---
> > > .../devicetree/bindings/mfd/qcom-rpm-smd.txt | 117 +++++++++++++++++++++
> > > include/dt-bindings/mfd/qcom-smd-rpm.h | 28 +++++
> > > 2 files changed, 145 insertions(+)
> > > create mode 100644 Documentation/devicetree/bindings/mfd/qcom-rpm-smd.txt
> > > create mode 100644 include/dt-bindings/mfd/qcom-smd-rpm.h
> > >
> > > diff --git a/Documentation/devicetree/bindings/mfd/qcom-rpm-smd.txt b/Documentation/devicetree/bindings/mfd/qcom-rpm-smd.txt
>
> [..]
>
> > > +- qcom,smd-channels:
> > > + Usage: required
> > > + Value type: <stringlist>
> > > + Definition: Shared Memory channel used for communication with the RPM
> >
> > This is going to require a DT Ack.
> >
> > Also, I don't see it being used anywhere.
>
> It's a common property of all smd devices, defining the smd channel this
> driver should bind to.
Well it's not in the kernel and I can't find the patch that uses it,
so my points still stand.
> > > += EXAMPLE
> > > +
> > > + smd {
> > > + compatible = "qcom,smd";
> >
> > Is an SMD (Shared Memory Device?) real hardware?
> >
>
> SMD is a mechanism for using shared memory for point-to-point
> communication channels with remote processors in all Qualcomm platforms.
>
> So it's not hardware, it's the control mechanism for communicating with
> real hardware.
Then you can't have a node for it. Virtual nodes which do not
represent real h/w are not allowed in Device Tree.
> > > + rpm {
> > > + interrupts = <0 168 1>;
> > > + qcom,ipc = <&apcs 8 0>;
> > > + qcom,smd-edge = <15>;
> >
> > The child node won't probe without a compatible string. Shouldn't
> > "qcom,rpm-msm8974" be in here instead?
> >
>
> These sub-nodes represents a logical grouping of the various channels
> that exist to this remote processor. For the rpm there is only the
> "rpm_requests" channel - used for sending regulator & clock requests.
Again, if it's not real h/w and don't have a proper driver, there
should be no reason for this node to exist.
> > > + rpm_requests {
> >
> > This node appears to be undocumented.
>
> This is the actual rpm device node, the smd & rpm nodes above are
> included for completeness of the example.
>
> They should perhaps be dropped to make this clearer.
>
> > Does it represent real h/w?
> >
>
> The other end of this smd channel is a micro controller that handles
> regulator and clock requests for the platform - so this is hardware.
>
> This is equivalent to the qcom_rpm driver, but instead of a hardware
> like register window this uses the same packet based messaging mechanism
> that's used for other remote peripherals in the Qualcomm platform.
This needs a good review by the DT guys.
> > > + compatible = "qcom,rpm-msm8974";
> > > + qcom,smd-channels = "rpm_requests";
> > > +
> > > + pm8941-regulators {
> > > + compatible = "qcom,rpm-pm8941-regulators";
> > > + vdd_l13_l20_l23_l24-supply = <&pm8941_boost>;
> >
> > I'd like Mark to glance at this.
> >
>
> Right.
>
> > > + pm8941_s3: s3 {
> > > + regulator-min-microvolt = <1800000>;
> > > + regulator-max-microvolt = <1800000>;
> >
> > Aren't these fixed regulators?
> >
>
> In this system configuration most of the regulators have fixed values,
> but the regulators (hw) are not fixed.
I'm not sure that's how it works. I believe 'max' and 'min' should
describe the upper and lower constraints of the regulator. The actual
value it runs it is selected elsewhere.
We still need Mark to look at this.
> > > + };
> > > +
> > > + pm8941_boost: s4 {
> > > + regulator-min-microvolt = <5000000>;
> > > + regulator-max-microvolt = <5000000>;
> > > + };
> > > +
> > > + pm8941_l20: l20 {
> > > + regulator-min-microvolt = <2950000>;
> > > + regulator-max-microvolt = <2950000>;
> > > + };
> > > + };
> > > + };
> > > + };
> > > + };
> > > +
>
> Thanks,
> Bjorn
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 39+ messages in thread* Re: [PATCH v2 05/11] mfd: devicetree: bindings: Add Qualcomm SMD based RPM DT binding
2015-07-23 13:31 ` Lee Jones
@ 2015-07-23 16:41 ` Bjorn Andersson
[not found] ` <20150723164128.GD4753-P9SbAA3LsXe39TS3lRcy0mP6iJigPa5YXqFh9Ls21Oc@public.gmane.org>
0 siblings, 1 reply; 39+ messages in thread
From: Bjorn Andersson @ 2015-07-23 16:41 UTC (permalink / raw)
To: Lee Jones, Mark Brown
Cc: bjorn-UYDU3/A3LUY, Andy Gross, Rob Herring, Pawel Moll,
Mark Rutland, Ian Campbell, Kumar Gala, Samuel Ortiz,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-arm-msm-u79uwXL29TY76Z2rM5mHXA
On Thu 23 Jul 06:31 PDT 2015, Lee Jones wrote:
> On Mon, 13 Jul 2015, Bjorn Andersson wrote:
>
> > On Tue 07 Jul 05:16 PDT 2015, Lee Jones wrote:
> >
> > > FAO Mark and DT chaps,
> > >
> > > > From: Bjorn Andersson <bjorn.andersson-/MT0OVThwyLZJqsBc5GL+g@public.gmane.org>
> > > >
> > > > Add binding documentation for the Qualcomm Resource Power Manager (RPM)
> > > > using shared memory (Qualcomm SMD) as transport mechanism. This is found
> > > > in 8974 and newer based devices.
> > > >
> > > > The binding currently describes the rpm itself and the regulator
> > > > subnodes.
> > > >
> > > > Signed-off-by: Bjorn Andersson <bjorn.andersson-/MT0OVThwyLZJqsBc5GL+g@public.gmane.org>
> > > > ---
> > > > .../devicetree/bindings/mfd/qcom-rpm-smd.txt | 117 +++++++++++++++++++++
> > > > include/dt-bindings/mfd/qcom-smd-rpm.h | 28 +++++
> > > > 2 files changed, 145 insertions(+)
> > > > create mode 100644 Documentation/devicetree/bindings/mfd/qcom-rpm-smd.txt
> > > > create mode 100644 include/dt-bindings/mfd/qcom-smd-rpm.h
> > > >
> > > > diff --git a/Documentation/devicetree/bindings/mfd/qcom-rpm-smd.txt b/Documentation/devicetree/bindings/mfd/qcom-rpm-smd.txt
> >
> > [..]
> >
> > > > +- qcom,smd-channels:
> > > > + Usage: required
> > > > + Value type: <stringlist>
> > > > + Definition: Shared Memory channel used for communication with the RPM
> > >
> > > This is going to require a DT Ack.
> > >
> > > Also, I don't see it being used anywhere.
> >
> > It's a common property of all smd devices, defining the smd channel this
> > driver should bind to.
>
> Well it's not in the kernel and I can't find the patch that uses it,
> so my points still stand.
>
Patch 3 in this series defines the binding and patch 4 is an
implementation of this binding.
> > > > += EXAMPLE
> > > > +
> > > > + smd {
> > > > + compatible = "qcom,smd";
> > >
> > > Is an SMD (Shared Memory Device?) real hardware?
> > >
> >
> > SMD is a mechanism for using shared memory for point-to-point
> > communication channels with remote processors in all Qualcomm platforms.
> >
> > So it's not hardware, it's the control mechanism for communicating with
> > real hardware.
>
> Then you can't have a node for it. Virtual nodes which do not
> represent real h/w are not allowed in Device Tree.
>
It represent the structure of a Qualcomm platform, but there's not a 1:1
mapping between this node and a discrete component. And without the
information it carries there's no way for us to reach e.g. the RPM -
which is a discrete physical component.
But I understand that this discussion should be held on patch 3 and with
the DT maintainers.
> > > > + rpm {
> > > > + interrupts = <0 168 1>;
> > > > + qcom,ipc = <&apcs 8 0>;
> > > > + qcom,smd-edge = <15>;
> > >
> > > The child node won't probe without a compatible string. Shouldn't
> > > "qcom,rpm-msm8974" be in here instead?
> > >
> >
> > These sub-nodes represents a logical grouping of the various channels
> > that exist to this remote processor. For the rpm there is only the
> > "rpm_requests" channel - used for sending regulator & clock requests.
>
> Again, if it's not real h/w and don't have a proper driver, there
> should be no reason for this node to exist.
>
We need to get hold of the interrupts and that regmap to be able to
communicate with the RPM. If this information is not in DT there will be
no communication - further we can not move it into the RPM node as with
all other remote processors (WiFi, DSP etc) these resources are shared
between a number of drivers.
> > > > + rpm_requests {
> > >
> > > This node appears to be undocumented.
> >
> > This is the actual rpm device node, the smd & rpm nodes above are
> > included for completeness of the example.
> >
> > They should perhaps be dropped to make this clearer.
> >
> > > Does it represent real h/w?
> > >
> >
> > The other end of this smd channel is a micro controller that handles
> > regulator and clock requests for the platform - so this is hardware.
> >
> > This is equivalent to the qcom_rpm driver, but instead of a hardware
> > like register window this uses the same packet based messaging mechanism
> > that's used for other remote peripherals in the Qualcomm platform.
>
> This needs a good review by the DT guys.
>
Sure
> > > > + compatible = "qcom,rpm-msm8974";
> > > > + qcom,smd-channels = "rpm_requests";
> > > > +
> > > > + pm8941-regulators {
> > > > + compatible = "qcom,rpm-pm8941-regulators";
> > > > + vdd_l13_l20_l23_l24-supply = <&pm8941_boost>;
> > >
> > > I'd like Mark to glance at this.
> > >
> >
> > Right.
> >
> > > > + pm8941_s3: s3 {
> > > > + regulator-min-microvolt = <1800000>;
> > > > + regulator-max-microvolt = <1800000>;
> > >
> > > Aren't these fixed regulators?
> > >
> >
> > In this system configuration most of the regulators have fixed values,
> > but the regulators (hw) are not fixed.
>
> I'm not sure that's how it works. I believe 'max' and 'min' should
> describe the upper and lower constraints of the regulator. The actual
> value it runs it is selected elsewhere.
>
The specified range of the regulator is 1.75-1.85V and this is handled
by the implementation, however the board designers have stated that it
is only allowed to be configured to 1.8V.
So DT is used to narrow the capabilities of the individual component to
something that's suitable for this particular system.
> We still need Mark to look at this.
>
Mark, would you mind giving us a statement on the regulator subnode of
this binding?
Regards,
Bjorn
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 39+ messages in thread
* [PATCH v2 06/11] mfd: qcom-smd-rpm: Driver for the Qualcomm RPM over SMD
2015-06-26 21:50 [PATCH v2 00/11] Qualcomm Shared Memory & RPM drivers bjorn
` (4 preceding siblings ...)
2015-06-26 21:50 ` [PATCH v2 05/11] mfd: devicetree: bindings: Add Qualcomm SMD based RPM DT binding bjorn
@ 2015-06-26 21:50 ` bjorn
2015-07-07 12:37 ` Lee Jones
2015-06-26 21:50 ` [PATCH v2 07/11] regulator: qcom: smd: Regulator driver for the Qualcomm RPM bjorn
` (4 subsequent siblings)
10 siblings, 1 reply; 39+ messages in thread
From: bjorn @ 2015-06-26 21:50 UTC (permalink / raw)
To: Andy Gross, Samuel Ortiz, Lee Jones
Cc: Mark Brown, linux-kernel, linux-arm-msm
From: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Driver for the Resource Power Manager (RPM) found in Qualcomm 8974 based
devices.
The driver exposes resources that child drivers can operate on; to
implementing regulator, clock and bus frequency drivers.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
---
drivers/mfd/Kconfig | 14 +++
drivers/mfd/Makefile | 1 +
drivers/mfd/qcom-smd-rpm.c | 236 +++++++++++++++++++++++++++++++++++++++
include/linux/mfd/qcom-smd-rpm.h | 35 ++++++
4 files changed, 286 insertions(+)
create mode 100644 drivers/mfd/qcom-smd-rpm.c
create mode 100644 include/linux/mfd/qcom-smd-rpm.h
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 6538159..666c812 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -656,6 +656,20 @@ config MFD_QCOM_RPM
Say M here if you want to include support for the Qualcomm RPM as a
module. This will build a module called "qcom_rpm".
+config MFD_QCOM_SMD_RPM
+ tristate "Qualcomm Resource Power Manager (RPM) over SMD"
+ depends on QCOM_SMD && OF
+ help
+ If you say yes to this option, support will be included for the
+ Resource Power Manager system found in the Qualcomm 8974 based
+ devices.
+
+ This is required to access many regulators, clocks and bus
+ frequencies controlled by the RPM on these devices.
+
+ Say M here if you want to include support for the Qualcomm RPM as a
+ module. This will build a module called "qcom-smd-rpm".
+
config MFD_SPMI_PMIC
tristate "Qualcomm SPMI PMICs"
depends on ARCH_QCOM || COMPILE_TEST
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index ea40e07..289bd24 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -156,6 +156,7 @@ obj-$(CONFIG_MFD_CS5535) += cs5535-mfd.o
obj-$(CONFIG_MFD_OMAP_USB_HOST) += omap-usb-host.o omap-usb-tll.o
obj-$(CONFIG_MFD_PM8921_CORE) += pm8921-core.o ssbi.o
obj-$(CONFIG_MFD_QCOM_RPM) += qcom_rpm.o
+obj-$(CONFIG_MFD_QCOM_SMD_RPM) += qcom-smd-rpm.o
obj-$(CONFIG_MFD_SPMI_PMIC) += qcom-spmi-pmic.o
obj-$(CONFIG_TPS65911_COMPARATOR) += tps65911-comparator.o
obj-$(CONFIG_MFD_TPS65090) += tps65090.o
diff --git a/drivers/mfd/qcom-smd-rpm.c b/drivers/mfd/qcom-smd-rpm.c
new file mode 100644
index 0000000..d6faf85
--- /dev/null
+++ b/drivers/mfd/qcom-smd-rpm.c
@@ -0,0 +1,236 @@
+/*
+ * Copyright (c) 2015, Sony Mobile Communications AB.
+ * Copyright (c) 2012-2013, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/of_platform.h>
+#include <linux/io.h>
+#include <linux/interrupt.h>
+
+#include <linux/soc/qcom/smd.h>
+#include <linux/mfd/qcom-smd-rpm.h>
+
+#include <dt-bindings/mfd/qcom-smd-rpm.h>
+
+#define RPM_REQUEST_TIMEOUT (5 * HZ)
+
+/**
+ * struct qcom_smd_rpm - state of the rpm device driver
+ * @rpm_channel: reference to the smd channel
+ * @ack: completion for acks
+ * @lock: mutual exclusion around the send/complete pair
+ * @ack_status: result of the rpm request
+ */
+struct qcom_smd_rpm {
+ struct qcom_smd_channel *rpm_channel;
+
+ struct completion ack;
+ struct mutex lock;
+ int ack_status;
+};
+
+/**
+ * struct qcom_rpm_header - header for all rpm requests and responses
+ * @service_type: identifier of the service
+ * @length: length of the payload
+ */
+struct qcom_rpm_header {
+ u32 service_type;
+ u32 length;
+};
+
+/**
+ * struct qcom_rpm_request - request message to the rpm
+ * @msg_id: identifier of the outgoing message
+ * @flags: active/sleep state flags
+ * @type: resource type
+ * @id: resource id
+ * @data_len: length of the payload following this header
+ */
+struct qcom_rpm_request {
+ u32 msg_id;
+ u32 flags;
+ u32 type;
+ u32 id;
+ u32 data_len;
+};
+
+/**
+ * struct qcom_rpm_message - response message from the rpm
+ * @msg_type: indicator of the type of message
+ * @length: the size of this message, including the message header
+ * @msg_id: message id
+ * @message: textual message from the rpm
+ *
+ * Multiple of these messages can be stacked in an rpm message.
+ */
+struct qcom_rpm_message {
+ u32 msg_type;
+ u32 length;
+ union {
+ u32 msg_id;
+ u8 message[0];
+ };
+};
+
+#define RPM_SERVICE_TYPE_REQUEST 0x00716572 /* "req\0" */
+
+#define RPM_MSG_TYPE_ERR 0x00727265 /* "err\0" */
+#define RPM_MSG_TYPE_MSG_ID 0x2367736d /* "msg#" */
+
+/**
+ * qcom_rpm_smd_write - write @buf to @type:@id
+ * @rpm: rpm handle
+ * @type: resource type
+ * @id: resource identifier
+ * @buf: the data to be written
+ * @count: number of bytes in @buf
+ */
+int qcom_rpm_smd_write(struct qcom_smd_rpm *rpm,
+ int state,
+ u32 type, u32 id,
+ void *buf,
+ size_t count)
+{
+ static unsigned msg_id = 1;
+ int left;
+ int ret;
+
+ struct {
+ struct qcom_rpm_header hdr;
+ struct qcom_rpm_request req;
+ u8 payload[count];
+ } pkt;
+
+ /* SMD packets to the RPM may not exceed 256 bytes */
+ if (WARN_ON(sizeof(pkt) >= 256))
+ return -EINVAL;
+
+ mutex_lock(&rpm->lock);
+
+ pkt.hdr.service_type = RPM_SERVICE_TYPE_REQUEST;
+ pkt.hdr.length = sizeof(struct qcom_rpm_request) + count;
+
+ pkt.req.msg_id = msg_id++;
+ pkt.req.flags = BIT(state);
+ pkt.req.type = type;
+ pkt.req.id = id;
+ pkt.req.data_len = count;
+ memcpy(pkt.payload, buf, count);
+
+ ret = qcom_smd_send(rpm->rpm_channel, &pkt, sizeof(pkt));
+ if (ret)
+ goto out;
+
+ left = wait_for_completion_timeout(&rpm->ack, RPM_REQUEST_TIMEOUT);
+ if (!left)
+ ret = -ETIMEDOUT;
+ else
+ ret = rpm->ack_status;
+
+out:
+ mutex_unlock(&rpm->lock);
+ return ret;
+}
+EXPORT_SYMBOL(qcom_rpm_smd_write);
+
+#define RPM_ERR_INVALID_RESOURCE "resource does not exist"
+
+static int qcom_smd_rpm_callback(struct qcom_smd_device *qsdev,
+ const void *data,
+ size_t count)
+{
+ const struct qcom_rpm_header *hdr = data;
+ const struct qcom_rpm_message *msg;
+ const size_t inv_res_len = sizeof(RPM_ERR_INVALID_RESOURCE) - 1;
+ struct qcom_smd_rpm *rpm = dev_get_drvdata(&qsdev->dev);
+ const u8 *buf = data + sizeof(struct qcom_rpm_header);
+ const u8 *end = buf + hdr->length;
+ int status = 0;
+
+ if (hdr->service_type != RPM_SERVICE_TYPE_REQUEST ||
+ hdr->length < sizeof(struct qcom_rpm_message)) {
+ dev_err(&qsdev->dev, "invalid request\n");
+ return 0;
+ }
+
+ while (buf < end) {
+ msg = (struct qcom_rpm_message *)buf;
+ switch (msg->msg_type) {
+ case RPM_MSG_TYPE_MSG_ID:
+ break;
+ case RPM_MSG_TYPE_ERR:
+ if (msg->length == inv_res_len &&
+ !memcmp(msg->message,
+ RPM_ERR_INVALID_RESOURCE,
+ inv_res_len))
+ status = -ENXIO;
+ else
+ status = -EIO;
+ break;
+ }
+
+ buf = PTR_ALIGN(buf + 2 * sizeof(u32) + msg->length, 4);
+ }
+
+ rpm->ack_status = status;
+ complete(&rpm->ack);
+ return 0;
+}
+
+static int qcom_smd_rpm_probe(struct qcom_smd_device *sdev)
+{
+ struct qcom_smd_rpm *rpm;
+
+ rpm = devm_kzalloc(&sdev->dev, sizeof(*rpm), GFP_KERNEL);
+ if (!rpm)
+ return -ENOMEM;
+
+ mutex_init(&rpm->lock);
+ init_completion(&rpm->ack);
+
+ rpm->rpm_channel = sdev->channel;
+
+ dev_set_drvdata(&sdev->dev, rpm);
+
+ return of_platform_populate(sdev->dev.of_node, NULL, NULL, &sdev->dev);
+}
+
+static void qcom_smd_rpm_remove(struct qcom_smd_device *sdev)
+{
+ of_platform_depopulate(&sdev->dev);
+}
+
+static const struct of_device_id qcom_smd_rpm_of_match[] = {
+ { .compatible = "qcom,rpm-msm8974" },
+ {}
+};
+MODULE_DEVICE_TABLE(of, qcom_smd_rpm_of_match);
+
+static struct qcom_smd_driver qcom_smd_rpm_driver = {
+ .probe = qcom_smd_rpm_probe,
+ .remove = qcom_smd_rpm_remove,
+ .callback = qcom_smd_rpm_callback,
+ .driver = {
+ .name = "qcom_smd_rpm",
+ .owner = THIS_MODULE,
+ .of_match_table = qcom_smd_rpm_of_match,
+ },
+};
+
+module_qcom_smd_driver(qcom_smd_rpm_driver);
+
+MODULE_AUTHOR("Bjorn Andersson <bjorn.andersson@sonymobile.com>");
+MODULE_DESCRIPTION("Qualcomm SMD backed RPM driver");
+MODULE_LICENSE("GPL v2");
diff --git a/include/linux/mfd/qcom-smd-rpm.h b/include/linux/mfd/qcom-smd-rpm.h
new file mode 100644
index 0000000..2a53dca
--- /dev/null
+++ b/include/linux/mfd/qcom-smd-rpm.h
@@ -0,0 +1,35 @@
+#ifndef __QCOM_SMD_RPM_H__
+#define __QCOM_SMD_RPM_H__
+
+struct qcom_smd_rpm;
+
+#define QCOM_SMD_RPM_ACTIVE_STATE 0
+#define QCOM_SMD_RPM_SLEEP_STATE 1
+
+/*
+ * Constants used for addressing resources in the RPM.
+ */
+#define QCOM_SMD_RPM_BOOST 0x61747362
+#define QCOM_SMD_RPM_BUS_CLK 0x316b6c63
+#define QCOM_SMD_RPM_BUS_MASTER 0x73616d62
+#define QCOM_SMD_RPM_BUS_SLAVE 0x766c7362
+#define QCOM_SMD_RPM_CLK_BUF_A 0x616B6C63
+#define QCOM_SMD_RPM_LDOA 0x616f646c
+#define QCOM_SMD_RPM_LDOB 0x626F646C
+#define QCOM_SMD_RPM_MEM_CLK 0x326b6c63
+#define QCOM_SMD_RPM_MISC_CLK 0x306b6c63
+#define QCOM_SMD_RPM_NCPA 0x6170636E
+#define QCOM_SMD_RPM_NCPB 0x6270636E
+#define QCOM_SMD_RPM_OCMEM_PWR 0x706d636f
+#define QCOM_SMD_RPM_QPIC_CLK 0x63697071
+#define QCOM_SMD_RPM_SMPA 0x61706d73
+#define QCOM_SMD_RPM_SMPB 0x62706d73
+#define QCOM_SMD_RPM_SPDM 0x63707362
+#define QCOM_SMD_RPM_VSA 0x00617376
+
+int qcom_rpm_smd_write(struct qcom_smd_rpm *rpm,
+ int state,
+ u32 resource_type, u32 resource_id,
+ void *buf, size_t count);
+
+#endif
--
1.9.3 (Apple Git-50)
^ permalink raw reply related [flat|nested] 39+ messages in thread* Re: [PATCH v2 06/11] mfd: qcom-smd-rpm: Driver for the Qualcomm RPM over SMD
2015-06-26 21:50 ` [PATCH v2 06/11] mfd: qcom-smd-rpm: Driver for the Qualcomm RPM over SMD bjorn
@ 2015-07-07 12:37 ` Lee Jones
2015-07-13 21:58 ` Bjorn Andersson
0 siblings, 1 reply; 39+ messages in thread
From: Lee Jones @ 2015-07-07 12:37 UTC (permalink / raw)
To: bjorn; +Cc: Andy Gross, Samuel Ortiz, Mark Brown, linux-kernel, linux-arm-msm
On Fri, 26 Jun 2015, bjorn@kryo.se wrote:
> From: Bjorn Andersson <bjorn.andersson@sonymobile.com>
>
> Driver for the Resource Power Manager (RPM) found in Qualcomm 8974 based
> devices.
> The driver exposes resources that child drivers can operate on; to
> implementing regulator, clock and bus frequency drivers.
>
> Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
> ---
> drivers/mfd/Kconfig | 14 +++
> drivers/mfd/Makefile | 1 +
> drivers/mfd/qcom-smd-rpm.c | 236 +++++++++++++++++++++++++++++++++++++++
> include/linux/mfd/qcom-smd-rpm.h | 35 ++++++
> 4 files changed, 286 insertions(+)
> create mode 100644 drivers/mfd/qcom-smd-rpm.c
> create mode 100644 include/linux/mfd/qcom-smd-rpm.h
>
> diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
> index 6538159..666c812 100644
> --- a/drivers/mfd/Kconfig
> +++ b/drivers/mfd/Kconfig
> @@ -656,6 +656,20 @@ config MFD_QCOM_RPM
> Say M here if you want to include support for the Qualcomm RPM as a
> module. This will build a module called "qcom_rpm".
>
> +config MFD_QCOM_SMD_RPM
> + tristate "Qualcomm Resource Power Manager (RPM) over SMD"
> + depends on QCOM_SMD && OF
> + help
> + If you say yes to this option, support will be included for the
> + Resource Power Manager system found in the Qualcomm 8974 based
> + devices.
> +
> + This is required to access many regulators, clocks and bus
> + frequencies controlled by the RPM on these devices.
> +
> + Say M here if you want to include support for the Qualcomm RPM as a
> + module. This will build a module called "qcom-smd-rpm".
I'm not exactly sure what makes this an MFD device.
> config MFD_SPMI_PMIC
> tristate "Qualcomm SPMI PMICs"
> depends on ARCH_QCOM || COMPILE_TEST
> diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
> index ea40e07..289bd24 100644
> --- a/drivers/mfd/Makefile
> +++ b/drivers/mfd/Makefile
> @@ -156,6 +156,7 @@ obj-$(CONFIG_MFD_CS5535) += cs5535-mfd.o
> obj-$(CONFIG_MFD_OMAP_USB_HOST) += omap-usb-host.o omap-usb-tll.o
> obj-$(CONFIG_MFD_PM8921_CORE) += pm8921-core.o ssbi.o
> obj-$(CONFIG_MFD_QCOM_RPM) += qcom_rpm.o
> +obj-$(CONFIG_MFD_QCOM_SMD_RPM) += qcom-smd-rpm.o
> obj-$(CONFIG_MFD_SPMI_PMIC) += qcom-spmi-pmic.o
> obj-$(CONFIG_TPS65911_COMPARATOR) += tps65911-comparator.o
> obj-$(CONFIG_MFD_TPS65090) += tps65090.o
> diff --git a/drivers/mfd/qcom-smd-rpm.c b/drivers/mfd/qcom-smd-rpm.c
> new file mode 100644
> index 0000000..d6faf85
> --- /dev/null
> +++ b/drivers/mfd/qcom-smd-rpm.c
> @@ -0,0 +1,236 @@
> +/*
> + * Copyright (c) 2015, Sony Mobile Communications AB.
> + * Copyright (c) 2012-2013, The Linux Foundation. All rights reserved.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 and
> + * only version 2 as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/of_platform.h>
> +#include <linux/io.h>
> +#include <linux/interrupt.h>
> +
> +#include <linux/soc/qcom/smd.h>
> +#include <linux/mfd/qcom-smd-rpm.h>
> +
> +#include <dt-bindings/mfd/qcom-smd-rpm.h>
> +
> +#define RPM_REQUEST_TIMEOUT (5 * HZ)
> +
> +/**
> + * struct qcom_smd_rpm - state of the rpm device driver
> + * @rpm_channel: reference to the smd channel
> + * @ack: completion for acks
> + * @lock: mutual exclusion around the send/complete pair
> + * @ack_status: result of the rpm request
> + */
> +struct qcom_smd_rpm {
> + struct qcom_smd_channel *rpm_channel;
> +
> + struct completion ack;
> + struct mutex lock;
> + int ack_status;
> +};
> +
> +/**
> + * struct qcom_rpm_header - header for all rpm requests and responses
> + * @service_type: identifier of the service
> + * @length: length of the payload
> + */
> +struct qcom_rpm_header {
> + u32 service_type;
> + u32 length;
> +};
> +
> +/**
> + * struct qcom_rpm_request - request message to the rpm
> + * @msg_id: identifier of the outgoing message
> + * @flags: active/sleep state flags
> + * @type: resource type
> + * @id: resource id
> + * @data_len: length of the payload following this header
> + */
> +struct qcom_rpm_request {
> + u32 msg_id;
> + u32 flags;
> + u32 type;
> + u32 id;
> + u32 data_len;
> +};
> +
> +/**
> + * struct qcom_rpm_message - response message from the rpm
> + * @msg_type: indicator of the type of message
> + * @length: the size of this message, including the message header
> + * @msg_id: message id
> + * @message: textual message from the rpm
> + *
> + * Multiple of these messages can be stacked in an rpm message.
> + */
> +struct qcom_rpm_message {
> + u32 msg_type;
> + u32 length;
> + union {
> + u32 msg_id;
> + u8 message[0];
> + };
> +};
> +
> +#define RPM_SERVICE_TYPE_REQUEST 0x00716572 /* "req\0" */
> +
> +#define RPM_MSG_TYPE_ERR 0x00727265 /* "err\0" */
> +#define RPM_MSG_TYPE_MSG_ID 0x2367736d /* "msg#" */
> +
> +/**
> + * qcom_rpm_smd_write - write @buf to @type:@id
> + * @rpm: rpm handle
> + * @type: resource type
> + * @id: resource identifier
> + * @buf: the data to be written
> + * @count: number of bytes in @buf
> + */
> +int qcom_rpm_smd_write(struct qcom_smd_rpm *rpm,
> + int state,
> + u32 type, u32 id,
> + void *buf,
> + size_t count)
> +{
> + static unsigned msg_id = 1;
> + int left;
> + int ret;
> +
> + struct {
> + struct qcom_rpm_header hdr;
> + struct qcom_rpm_request req;
> + u8 payload[count];
> + } pkt;
> +
> + /* SMD packets to the RPM may not exceed 256 bytes */
> + if (WARN_ON(sizeof(pkt) >= 256))
> + return -EINVAL;
> +
> + mutex_lock(&rpm->lock);
> +
> + pkt.hdr.service_type = RPM_SERVICE_TYPE_REQUEST;
> + pkt.hdr.length = sizeof(struct qcom_rpm_request) + count;
> +
> + pkt.req.msg_id = msg_id++;
> + pkt.req.flags = BIT(state);
> + pkt.req.type = type;
> + pkt.req.id = id;
> + pkt.req.data_len = count;
> + memcpy(pkt.payload, buf, count);
> +
> + ret = qcom_smd_send(rpm->rpm_channel, &pkt, sizeof(pkt));
> + if (ret)
> + goto out;
> +
> + left = wait_for_completion_timeout(&rpm->ack, RPM_REQUEST_TIMEOUT);
> + if (!left)
> + ret = -ETIMEDOUT;
> + else
> + ret = rpm->ack_status;
> +
> +out:
> + mutex_unlock(&rpm->lock);
> + return ret;
> +}
> +EXPORT_SYMBOL(qcom_rpm_smd_write);
> +
> +#define RPM_ERR_INVALID_RESOURCE "resource does not exist"
I don't like this at all.
> +static int qcom_smd_rpm_callback(struct qcom_smd_device *qsdev,
> + const void *data,
> + size_t count)
> +{
> + const struct qcom_rpm_header *hdr = data;
> + const struct qcom_rpm_message *msg;
> + const size_t inv_res_len = sizeof(RPM_ERR_INVALID_RESOURCE) - 1;
> + struct qcom_smd_rpm *rpm = dev_get_drvdata(&qsdev->dev);
> + const u8 *buf = data + sizeof(struct qcom_rpm_header);
> + const u8 *end = buf + hdr->length;
> + int status = 0;
> +
> + if (hdr->service_type != RPM_SERVICE_TYPE_REQUEST ||
> + hdr->length < sizeof(struct qcom_rpm_message)) {
> + dev_err(&qsdev->dev, "invalid request\n");
> + return 0;
> + }
> +
> + while (buf < end) {
> + msg = (struct qcom_rpm_message *)buf;
> + switch (msg->msg_type) {
> + case RPM_MSG_TYPE_MSG_ID:
> + break;
> + case RPM_MSG_TYPE_ERR:
> + if (msg->length == inv_res_len &&
> + !memcmp(msg->message,
> + RPM_ERR_INVALID_RESOURCE,
> + inv_res_len))
strncpy(msg->message, "resource does not exist", 23);
> + status = -ENXIO;
> + else
> + status = -EIO;
> + break;
> + }
> +
> + buf = PTR_ALIGN(buf + 2 * sizeof(u32) + msg->length, 4);
> + }
> +
> + rpm->ack_status = status;
> + complete(&rpm->ack);
> + return 0;
> +}
> +
> +static int qcom_smd_rpm_probe(struct qcom_smd_device *sdev)
> +{
> + struct qcom_smd_rpm *rpm;
> +
> + rpm = devm_kzalloc(&sdev->dev, sizeof(*rpm), GFP_KERNEL);
> + if (!rpm)
> + return -ENOMEM;
> +
> + mutex_init(&rpm->lock);
> + init_completion(&rpm->ack);
> +
> + rpm->rpm_channel = sdev->channel;
> +
> + dev_set_drvdata(&sdev->dev, rpm);
> +
> + return of_platform_populate(sdev->dev.of_node, NULL, NULL, &sdev->dev);
> +}
> +
> +static void qcom_smd_rpm_remove(struct qcom_smd_device *sdev)
> +{
> + of_platform_depopulate(&sdev->dev);
> +}
> +
> +static const struct of_device_id qcom_smd_rpm_of_match[] = {
> + { .compatible = "qcom,rpm-msm8974" },
> + {}
> +};
> +MODULE_DEVICE_TABLE(of, qcom_smd_rpm_of_match);
> +
> +static struct qcom_smd_driver qcom_smd_rpm_driver = {
> + .probe = qcom_smd_rpm_probe,
> + .remove = qcom_smd_rpm_remove,
> + .callback = qcom_smd_rpm_callback,
> + .driver = {
> + .name = "qcom_smd_rpm",
> + .owner = THIS_MODULE,
Remove this line.
> + .of_match_table = qcom_smd_rpm_of_match,
> + },
> +};
> +
> +module_qcom_smd_driver(qcom_smd_rpm_driver);
> +
> +MODULE_AUTHOR("Bjorn Andersson <bjorn.andersson@sonymobile.com>");
> +MODULE_DESCRIPTION("Qualcomm SMD backed RPM driver");
> +MODULE_LICENSE("GPL v2");
> diff --git a/include/linux/mfd/qcom-smd-rpm.h b/include/linux/mfd/qcom-smd-rpm.h
> new file mode 100644
> index 0000000..2a53dca
> --- /dev/null
> +++ b/include/linux/mfd/qcom-smd-rpm.h
> @@ -0,0 +1,35 @@
> +#ifndef __QCOM_SMD_RPM_H__
> +#define __QCOM_SMD_RPM_H__
> +
> +struct qcom_smd_rpm;
> +
> +#define QCOM_SMD_RPM_ACTIVE_STATE 0
> +#define QCOM_SMD_RPM_SLEEP_STATE 1
> +
> +/*
> + * Constants used for addressing resources in the RPM.
> + */
> +#define QCOM_SMD_RPM_BOOST 0x61747362
> +#define QCOM_SMD_RPM_BUS_CLK 0x316b6c63
> +#define QCOM_SMD_RPM_BUS_MASTER 0x73616d62
> +#define QCOM_SMD_RPM_BUS_SLAVE 0x766c7362
> +#define QCOM_SMD_RPM_CLK_BUF_A 0x616B6C63
> +#define QCOM_SMD_RPM_LDOA 0x616f646c
> +#define QCOM_SMD_RPM_LDOB 0x626F646C
> +#define QCOM_SMD_RPM_MEM_CLK 0x326b6c63
> +#define QCOM_SMD_RPM_MISC_CLK 0x306b6c63
> +#define QCOM_SMD_RPM_NCPA 0x6170636E
> +#define QCOM_SMD_RPM_NCPB 0x6270636E
> +#define QCOM_SMD_RPM_OCMEM_PWR 0x706d636f
> +#define QCOM_SMD_RPM_QPIC_CLK 0x63697071
> +#define QCOM_SMD_RPM_SMPA 0x61706d73
> +#define QCOM_SMD_RPM_SMPB 0x62706d73
> +#define QCOM_SMD_RPM_SPDM 0x63707362
> +#define QCOM_SMD_RPM_VSA 0x00617376
> +
> +int qcom_rpm_smd_write(struct qcom_smd_rpm *rpm,
> + int state,
> + u32 resource_type, u32 resource_id,
> + void *buf, size_t count);
> +
> +#endif
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 39+ messages in thread* Re: [PATCH v2 06/11] mfd: qcom-smd-rpm: Driver for the Qualcomm RPM over SMD
2015-07-07 12:37 ` Lee Jones
@ 2015-07-13 21:58 ` Bjorn Andersson
2015-07-23 13:22 ` Lee Jones
0 siblings, 1 reply; 39+ messages in thread
From: Bjorn Andersson @ 2015-07-13 21:58 UTC (permalink / raw)
To: Lee Jones
Cc: bjorn, Andy Gross, Samuel Ortiz, Mark Brown, linux-kernel, linux-arm-msm
On Tue 07 Jul 05:37 PDT 2015, Lee Jones wrote:
> On Fri, 26 Jun 2015, bjorn@kryo.se wrote:
>
> > From: Bjorn Andersson <bjorn.andersson@sonymobile.com>
[..]
> > diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
[..]
> > +config MFD_QCOM_SMD_RPM
> > + tristate "Qualcomm Resource Power Manager (RPM) over SMD"
> > + depends on QCOM_SMD && OF
> > + help
> > + If you say yes to this option, support will be included for the
> > + Resource Power Manager system found in the Qualcomm 8974 based
> > + devices.
> > +
> > + This is required to access many regulators, clocks and bus
> > + frequencies controlled by the RPM on these devices.
> > +
> > + Say M here if you want to include support for the Qualcomm RPM as a
> > + module. This will build a module called "qcom-smd-rpm".
>
> I'm not exactly sure what makes this an MFD device.
>
It represents a piece of hardware (a micro-controller) that exposes
control of a multitude of regulators and clocks in the Qualcomm
platforms.
It's basically just a successor of the qcom_rpm driver - same
functionality but a new communication method is used.
[..]
> > diff --git a/drivers/mfd/qcom-smd-rpm.c b/drivers/mfd/qcom-smd-rpm.c
[..]
> > +
> > +#define RPM_ERR_INVALID_RESOURCE "resource does not exist"
>
> I don't like this at all.
>
Which part of it?
It should probably be a static const char *, inlined in the function
below. Would that be to your liking?
> > +static int qcom_smd_rpm_callback(struct qcom_smd_device *qsdev,
> > + const void *data,
> > + size_t count)
> > +{
> > + const struct qcom_rpm_header *hdr = data;
> > + const struct qcom_rpm_message *msg;
> > + const size_t inv_res_len = sizeof(RPM_ERR_INVALID_RESOURCE) - 1;
> > + struct qcom_smd_rpm *rpm = dev_get_drvdata(&qsdev->dev);
> > + const u8 *buf = data + sizeof(struct qcom_rpm_header);
> > + const u8 *end = buf + hdr->length;
> > + int status = 0;
> > +
> > + if (hdr->service_type != RPM_SERVICE_TYPE_REQUEST ||
> > + hdr->length < sizeof(struct qcom_rpm_message)) {
> > + dev_err(&qsdev->dev, "invalid request\n");
> > + return 0;
> > + }
> > +
> > + while (buf < end) {
> > + msg = (struct qcom_rpm_message *)buf;
> > + switch (msg->msg_type) {
> > + case RPM_MSG_TYPE_MSG_ID:
> > + break;
> > + case RPM_MSG_TYPE_ERR:
> > + if (msg->length == inv_res_len &&
> > + !memcmp(msg->message,
> > + RPM_ERR_INVALID_RESOURCE,
> > + inv_res_len))
>
> strncpy(msg->message, "resource does not exist", 23);
>
No, I want to compare the content of msg->message with the string
"resource does not exist" - as that's the only way to know what type of
error we got.
This is unfortunately how the protocol looks :/
> > + status = -ENXIO;
> > + else
> > + status = -EIO;
> > + break;
> > + }
> > +
> > + buf = PTR_ALIGN(buf + 2 * sizeof(u32) + msg->length, 4);
> > + }
> > +
> > + rpm->ack_status = status;
> > + complete(&rpm->ack);
> > + return 0;
> > +}
> > +
[..]
> > +
> > +static struct qcom_smd_driver qcom_smd_rpm_driver = {
> > + .probe = qcom_smd_rpm_probe,
> > + .remove = qcom_smd_rpm_remove,
> > + .callback = qcom_smd_rpm_callback,
> > + .driver = {
> > + .name = "qcom_smd_rpm",
> > + .owner = THIS_MODULE,
>
> Remove this line.
>
The module_qcom_smd_driver does not initialize the .owner, but to follow
the general direction of the kernel I can add that to the macro...
> > + .of_match_table = qcom_smd_rpm_of_match,
> > + },
> > +};
> > +
> > +module_qcom_smd_driver(qcom_smd_rpm_driver);
> > +
> > +MODULE_AUTHOR("Bjorn Andersson <bjorn.andersson@sonymobile.com>");
> > +MODULE_DESCRIPTION("Qualcomm SMD backed RPM driver");
> > +MODULE_LICENSE("GPL v2");
Thanks,
Bjorn
^ permalink raw reply [flat|nested] 39+ messages in thread* Re: [PATCH v2 06/11] mfd: qcom-smd-rpm: Driver for the Qualcomm RPM over SMD
2015-07-13 21:58 ` Bjorn Andersson
@ 2015-07-23 13:22 ` Lee Jones
2015-07-23 16:55 ` Bjorn Andersson
0 siblings, 1 reply; 39+ messages in thread
From: Lee Jones @ 2015-07-23 13:22 UTC (permalink / raw)
To: Bjorn Andersson
Cc: bjorn, Andy Gross, Samuel Ortiz, Mark Brown, linux-kernel, linux-arm-msm
On Mon, 13 Jul 2015, Bjorn Andersson wrote:
> On Tue 07 Jul 05:37 PDT 2015, Lee Jones wrote:
>
> > On Fri, 26 Jun 2015, bjorn@kryo.se wrote:
> >
> > > From: Bjorn Andersson <bjorn.andersson@sonymobile.com>
> [..]
>
> > > diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
>
> [..]
>
> > > +config MFD_QCOM_SMD_RPM
> > > + tristate "Qualcomm Resource Power Manager (RPM) over SMD"
> > > + depends on QCOM_SMD && OF
> > > + help
> > > + If you say yes to this option, support will be included for the
> > > + Resource Power Manager system found in the Qualcomm 8974 based
> > > + devices.
> > > +
> > > + This is required to access many regulators, clocks and bus
> > > + frequencies controlled by the RPM on these devices.
> > > +
> > > + Say M here if you want to include support for the Qualcomm RPM as a
> > > + module. This will build a module called "qcom-smd-rpm".
> >
> > I'm not exactly sure what makes this an MFD device.
> >
>
> It represents a piece of hardware (a micro-controller) that exposes
> control of a multitude of regulators and clocks in the Qualcomm
> platforms.
>
> It's basically just a successor of the qcom_rpm driver - same
> functionality but a new communication method is used.
My point still stands. Please investigate moving this (and the
qcom_rpm driver if it's the same) into either drivers/soc or
drivers/platform. The support in these two directories _seem_ to be
pretty similar.
> > > diff --git a/drivers/mfd/qcom-smd-rpm.c b/drivers/mfd/qcom-smd-rpm.c
>
> [..]
>
> > > +
> > > +#define RPM_ERR_INVALID_RESOURCE "resource does not exist"
> >
> > I don't like this at all.
> >
>
> Which part of it?
>
> It should probably be a static const char *, inlined in the function
> below. Would that be to your liking?
It would be better, but I never really see the point in initialising
variables with these types of messages. I'd get rid of the
superfluous chuff and just do:
memcmp(msg->message, "resource does not exist", 23);
> > > +static int qcom_smd_rpm_callback(struct qcom_smd_device *qsdev,
> > > + const void *data,
> > > + size_t count)
> > > +{
> > > + const struct qcom_rpm_header *hdr = data;
> > > + const struct qcom_rpm_message *msg;
> > > + const size_t inv_res_len = sizeof(RPM_ERR_INVALID_RESOURCE) - 1;
> > > + struct qcom_smd_rpm *rpm = dev_get_drvdata(&qsdev->dev);
> > > + const u8 *buf = data + sizeof(struct qcom_rpm_header);
> > > + const u8 *end = buf + hdr->length;
> > > + int status = 0;
> > > +
> > > + if (hdr->service_type != RPM_SERVICE_TYPE_REQUEST ||
> > > + hdr->length < sizeof(struct qcom_rpm_message)) {
> > > + dev_err(&qsdev->dev, "invalid request\n");
> > > + return 0;
> > > + }
> > > +
> > > + while (buf < end) {
> > > + msg = (struct qcom_rpm_message *)buf;
> > > + switch (msg->msg_type) {
> > > + case RPM_MSG_TYPE_MSG_ID:
> > > + break;
> > > + case RPM_MSG_TYPE_ERR:
> > > + if (msg->length == inv_res_len &&
> > > + !memcmp(msg->message,
> > > + RPM_ERR_INVALID_RESOURCE,
> > > + inv_res_len))
> >
> > strncpy(msg->message, "resource does not exist", 23);
> >
>
> No, I want to compare the content of msg->message with the string
Yes, I just noticed that.
> "resource does not exist" - as that's the only way to know what type of
> error we got.
>
> This is unfortunately how the protocol looks :/
What about either my memcmp suggestion above or this then:
strncmp(msg->message, "resource does not exist", 23);
> > > + status = -ENXIO;
> > > + else
> > > + status = -EIO;
> > > + break;
> > > + }
> > > +
> > > + buf = PTR_ALIGN(buf + 2 * sizeof(u32) + msg->length, 4);
> > > + }
> > > +
> > > + rpm->ack_status = status;
> > > + complete(&rpm->ack);
> > > + return 0;
> > > +}
> > > +
>
> [..]
>
> > > +
> > > +static struct qcom_smd_driver qcom_smd_rpm_driver = {
> > > + .probe = qcom_smd_rpm_probe,
> > > + .remove = qcom_smd_rpm_remove,
> > > + .callback = qcom_smd_rpm_callback,
> > > + .driver = {
> > > + .name = "qcom_smd_rpm",
> > > + .owner = THIS_MODULE,
> >
> > Remove this line.
Still not 100% sure why you need your own 'special' driver struct. If
it's for the .callback, there are other ways to do this without having
to invent your own bus.
> The module_qcom_smd_driver does not initialize the .owner, but to follow
> the general direction of the kernel I can add that to the macro...
>
> > > + .of_match_table = qcom_smd_rpm_of_match,
> > > + },
> > > +};
> > > +
> > > +module_qcom_smd_driver(qcom_smd_rpm_driver);
> > > +
> > > +MODULE_AUTHOR("Bjorn Andersson <bjorn.andersson@sonymobile.com>");
> > > +MODULE_DESCRIPTION("Qualcomm SMD backed RPM driver");
> > > +MODULE_LICENSE("GPL v2");
>
> Thanks,
> Bjorn
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 39+ messages in thread* Re: [PATCH v2 06/11] mfd: qcom-smd-rpm: Driver for the Qualcomm RPM over SMD
2015-07-23 13:22 ` Lee Jones
@ 2015-07-23 16:55 ` Bjorn Andersson
2015-07-24 10:06 ` Lee Jones
0 siblings, 1 reply; 39+ messages in thread
From: Bjorn Andersson @ 2015-07-23 16:55 UTC (permalink / raw)
To: Lee Jones
Cc: bjorn, Andy Gross, Samuel Ortiz, Mark Brown, linux-kernel, linux-arm-msm
On Thu 23 Jul 06:22 PDT 2015, Lee Jones wrote:
> On Mon, 13 Jul 2015, Bjorn Andersson wrote:
>
> > On Tue 07 Jul 05:37 PDT 2015, Lee Jones wrote:
> >
> > > On Fri, 26 Jun 2015, bjorn@kryo.se wrote:
> > >
> > > > From: Bjorn Andersson <bjorn.andersson@sonymobile.com>
> > [..]
> >
> > > > diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
> >
> > [..]
> >
> > > > +config MFD_QCOM_SMD_RPM
> > > > + tristate "Qualcomm Resource Power Manager (RPM) over SMD"
> > > > + depends on QCOM_SMD && OF
> > > > + help
> > > > + If you say yes to this option, support will be included for the
> > > > + Resource Power Manager system found in the Qualcomm 8974 based
> > > > + devices.
> > > > +
> > > > + This is required to access many regulators, clocks and bus
> > > > + frequencies controlled by the RPM on these devices.
> > > > +
> > > > + Say M here if you want to include support for the Qualcomm RPM as a
> > > > + module. This will build a module called "qcom-smd-rpm".
> > >
> > > I'm not exactly sure what makes this an MFD device.
> > >
> >
> > It represents a piece of hardware (a micro-controller) that exposes
> > control of a multitude of regulators and clocks in the Qualcomm
> > platforms.
> >
> > It's basically just a successor of the qcom_rpm driver - same
> > functionality but a new communication method is used.
>
> My point still stands. Please investigate moving this (and the
> qcom_rpm driver if it's the same) into either drivers/soc or
> drivers/platform. The support in these two directories _seem_ to be
> pretty similar.
>
We had this exact discussion last year and I argued that a piece of
hardware that exposes regulators and clocks - like most PMICs - is a
mfd and you agreed and picked the driver.
I will have a word with Andy about moving this and the qcom_rpm driver
out of mfd.
> > > > diff --git a/drivers/mfd/qcom-smd-rpm.c b/drivers/mfd/qcom-smd-rpm.c
> >
> > [..]
> >
> > > > +
> > > > +#define RPM_ERR_INVALID_RESOURCE "resource does not exist"
> > >
> > > I don't like this at all.
> > >
> >
> > Which part of it?
> >
> > It should probably be a static const char *, inlined in the function
> > below. Would that be to your liking?
>
> It would be better, but I never really see the point in initialising
> variables with these types of messages. I'd get rid of the
> superfluous chuff and just do:
>
> memcmp(msg->message, "resource does not exist", 23);
>
The point was simply to not have to write:
if (msg->length == 23 && memcmp(msg->message, ..., 23);
Simply because I don't like the first part of the expression. I'll
rewrite it...
> > > > +static int qcom_smd_rpm_callback(struct qcom_smd_device *qsdev,
> > > > + const void *data,
> > > > + size_t count)
> > > > +{
> > > > + const struct qcom_rpm_header *hdr = data;
> > > > + const struct qcom_rpm_message *msg;
> > > > + const size_t inv_res_len = sizeof(RPM_ERR_INVALID_RESOURCE) - 1;
> > > > + struct qcom_smd_rpm *rpm = dev_get_drvdata(&qsdev->dev);
> > > > + const u8 *buf = data + sizeof(struct qcom_rpm_header);
> > > > + const u8 *end = buf + hdr->length;
> > > > + int status = 0;
> > > > +
> > > > + if (hdr->service_type != RPM_SERVICE_TYPE_REQUEST ||
> > > > + hdr->length < sizeof(struct qcom_rpm_message)) {
> > > > + dev_err(&qsdev->dev, "invalid request\n");
> > > > + return 0;
> > > > + }
> > > > +
> > > > + while (buf < end) {
> > > > + msg = (struct qcom_rpm_message *)buf;
> > > > + switch (msg->msg_type) {
> > > > + case RPM_MSG_TYPE_MSG_ID:
> > > > + break;
> > > > + case RPM_MSG_TYPE_ERR:
> > > > + if (msg->length == inv_res_len &&
> > > > + !memcmp(msg->message,
> > > > + RPM_ERR_INVALID_RESOURCE,
> > > > + inv_res_len))
> > >
> > > strncpy(msg->message, "resource does not exist", 23);
> > >
> >
> > No, I want to compare the content of msg->message with the string
>
> Yes, I just noticed that.
>
> > "resource does not exist" - as that's the only way to know what type of
> > error we got.
> >
> > This is unfortunately how the protocol looks :/
>
> What about either my memcmp suggestion above or this then:
>
> strncmp(msg->message, "resource does not exist", 23);
>
That would require the string to be 0-terminated.
[..]
> > > > +static struct qcom_smd_driver qcom_smd_rpm_driver = {
> > > > + .probe = qcom_smd_rpm_probe,
> > > > + .remove = qcom_smd_rpm_remove,
> > > > + .callback = qcom_smd_rpm_callback,
> > > > + .driver = {
> > > > + .name = "qcom_smd_rpm",
> > > > + .owner = THIS_MODULE,
> > >
> > > Remove this line.
>
> Still not 100% sure why you need your own 'special' driver struct. If
> it's for the .callback, there are other ways to do this without having
> to invent your own bus.
>
Because the life cycle of these components are much like, say, USB -
they can come and go. As such e.g. a platform_driver is not a good fit.
Regards,
Bjorn
^ permalink raw reply [flat|nested] 39+ messages in thread* Re: [PATCH v2 06/11] mfd: qcom-smd-rpm: Driver for the Qualcomm RPM over SMD
2015-07-23 16:55 ` Bjorn Andersson
@ 2015-07-24 10:06 ` Lee Jones
0 siblings, 0 replies; 39+ messages in thread
From: Lee Jones @ 2015-07-24 10:06 UTC (permalink / raw)
To: Bjorn Andersson
Cc: bjorn, Andy Gross, Samuel Ortiz, Mark Brown, linux-kernel, linux-arm-msm
On Thu, 23 Jul 2015, Bjorn Andersson wrote:
> On Thu 23 Jul 06:22 PDT 2015, Lee Jones wrote:
>
> > On Mon, 13 Jul 2015, Bjorn Andersson wrote:
> >
> > > On Tue 07 Jul 05:37 PDT 2015, Lee Jones wrote:
> > >
> > > > On Fri, 26 Jun 2015, bjorn@kryo.se wrote:
> > > >
> > > > > From: Bjorn Andersson <bjorn.andersson@sonymobile.com>
> > > [..]
> > >
> > > > > diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
> > >
> > > [..]
> > >
> > > > > +config MFD_QCOM_SMD_RPM
> > > > > + tristate "Qualcomm Resource Power Manager (RPM) over SMD"
> > > > > + depends on QCOM_SMD && OF
> > > > > + help
> > > > > + If you say yes to this option, support will be included for the
> > > > > + Resource Power Manager system found in the Qualcomm 8974 based
> > > > > + devices.
> > > > > +
> > > > > + This is required to access many regulators, clocks and bus
> > > > > + frequencies controlled by the RPM on these devices.
> > > > > +
> > > > > + Say M here if you want to include support for the Qualcomm RPM as a
> > > > > + module. This will build a module called "qcom-smd-rpm".
> > > >
> > > > I'm not exactly sure what makes this an MFD device.
> > > >
> > >
> > > It represents a piece of hardware (a micro-controller) that exposes
> > > control of a multitude of regulators and clocks in the Qualcomm
> > > platforms.
> > >
> > > It's basically just a successor of the qcom_rpm driver - same
> > > functionality but a new communication method is used.
> >
> > My point still stands. Please investigate moving this (and the
> > qcom_rpm driver if it's the same) into either drivers/soc or
> > drivers/platform. The support in these two directories _seem_ to be
> > pretty similar.
> >
>
> We had this exact discussion last year and I argued that a piece of
> hardware that exposes regulators and clocks - like most PMICs - is a
> mfd and you agreed and picked the driver.
I've become stricter since then. An IC which only does power
management should either live in drivers/power, or more recently they
have been described as platform specific drivers which have
subsequently been moved to drivers/platform. Particularly if they have
their own special, platform specific communication method/bus.
> I will have a word with Andy about moving this and the qcom_rpm driver
> out of mfd.
Thanks.
> > > > > diff --git a/drivers/mfd/qcom-smd-rpm.c b/drivers/mfd/qcom-smd-rpm.c
> > >
> > > [..]
> > >
> > > > > +
> > > > > +#define RPM_ERR_INVALID_RESOURCE "resource does not exist"
> > > >
> > > > I don't like this at all.
> > > >
> > >
> > > Which part of it?
> > >
> > > It should probably be a static const char *, inlined in the function
> > > below. Would that be to your liking?
> >
> > It would be better, but I never really see the point in initialising
> > variables with these types of messages. I'd get rid of the
> > superfluous chuff and just do:
> >
> > memcmp(msg->message, "resource does not exist", 23);
> >
>
> The point was simply to not have to write:
>
> if (msg->length == 23 && memcmp(msg->message, ..., 23);
>
> Simply because I don't like the first part of the expression. I'll
> rewrite it...
All this cruft just to avoid that?
Just define '23', then code looks good and problem vaporises.
> > > > > +static int qcom_smd_rpm_callback(struct qcom_smd_device *qsdev,
> > > > > + const void *data,
> > > > > + size_t count)
> > > > > +{
> > > > > + const struct qcom_rpm_header *hdr = data;
> > > > > + const struct qcom_rpm_message *msg;
> > > > > + const size_t inv_res_len = sizeof(RPM_ERR_INVALID_RESOURCE) - 1;
> > > > > + struct qcom_smd_rpm *rpm = dev_get_drvdata(&qsdev->dev);
> > > > > + const u8 *buf = data + sizeof(struct qcom_rpm_header);
> > > > > + const u8 *end = buf + hdr->length;
> > > > > + int status = 0;
> > > > > +
> > > > > + if (hdr->service_type != RPM_SERVICE_TYPE_REQUEST ||
> > > > > + hdr->length < sizeof(struct qcom_rpm_message)) {
> > > > > + dev_err(&qsdev->dev, "invalid request\n");
> > > > > + return 0;
> > > > > + }
> > > > > +
> > > > > + while (buf < end) {
> > > > > + msg = (struct qcom_rpm_message *)buf;
> > > > > + switch (msg->msg_type) {
> > > > > + case RPM_MSG_TYPE_MSG_ID:
> > > > > + break;
> > > > > + case RPM_MSG_TYPE_ERR:
> > > > > + if (msg->length == inv_res_len &&
> > > > > + !memcmp(msg->message,
> > > > > + RPM_ERR_INVALID_RESOURCE,
> > > > > + inv_res_len))
> > > >
> > > > strncpy(msg->message, "resource does not exist", 23);
> > > >
> > >
> > > No, I want to compare the content of msg->message with the string
> >
> > Yes, I just noticed that.
> >
> > > "resource does not exist" - as that's the only way to know what type of
> > > error we got.
> > >
> > > This is unfortunately how the protocol looks :/
> >
> > What about either my memcmp suggestion above or this then:
> >
> > strncmp(msg->message, "resource does not exist", 23);
> >
>
> That would require the string to be 0-terminated.
No it doesn't.
strNcmp, only compares the first N characters.
> > > > > +static struct qcom_smd_driver qcom_smd_rpm_driver = {
> > > > > + .probe = qcom_smd_rpm_probe,
> > > > > + .remove = qcom_smd_rpm_remove,
> > > > > + .callback = qcom_smd_rpm_callback,
> > > > > + .driver = {
> > > > > + .name = "qcom_smd_rpm",
> > > > > + .owner = THIS_MODULE,
> > > >
> > > > Remove this line.
> >
> > Still not 100% sure why you need your own 'special' driver struct. If
> > it's for the .callback, there are other ways to do this without having
> > to invent your own bus.
>
> Because the life cycle of these components are much like, say, USB -
> they can come and go. As such e.g. a platform_driver is not a good fit.
You mean they are hot-swappable? Don't we have any platform devices
which support that already?
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 39+ messages in thread
* [PATCH v2 07/11] regulator: qcom: smd: Regulator driver for the Qualcomm RPM
2015-06-26 21:50 [PATCH v2 00/11] Qualcomm Shared Memory & RPM drivers bjorn
` (5 preceding siblings ...)
2015-06-26 21:50 ` [PATCH v2 06/11] mfd: qcom-smd-rpm: Driver for the Qualcomm RPM over SMD bjorn
@ 2015-06-26 21:50 ` bjorn
2015-06-26 21:50 ` [PATCH v2 08/11] ARM: dts: msm8974: Add tcsr mutex node bjorn
` (3 subsequent siblings)
10 siblings, 0 replies; 39+ messages in thread
From: bjorn @ 2015-06-26 21:50 UTC (permalink / raw)
To: Liam Girdwood, Mark Brown; +Cc: Andy Gross, linux-arm-msm, linux-kernel
From: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Driver for regulators exposed by the Resource Power Manager (RPM) found
in devices based on Qualcomm 8974 and newer platforms.
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
---
drivers/regulator/Kconfig | 12 ++
drivers/regulator/Makefile | 1 +
drivers/regulator/qcom_smd-regulator.c | 350 +++++++++++++++++++++++++++++++++
3 files changed, 363 insertions(+)
create mode 100644 drivers/regulator/qcom_smd-regulator.c
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index bef3bde..876e03e 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -522,6 +522,18 @@ config REGULATOR_QCOM_RPM
Qualcomm RPM as a module. The module will be named
"qcom_rpm-regulator".
+config REGULATOR_QCOM_SMD_RPM
+ tristate "Qualcomm SMD based RPM regulator driver"
+ depends on MFD_QCOM_SMD_RPM
+ help
+ If you say yes to this option, support will be included for the
+ regulators exposed by the Resource Power Manager found in Qualcomm
+ 8974 based devices.
+
+ Say M here if you want to include support for the regulators on the
+ Qualcomm RPM as a module. The module will be named
+ "qcom_smd-regulator".
+
config REGULATOR_QCOM_SPMI
tristate "Qualcomm SPMI regulator driver"
depends on SPMI || COMPILE_TEST
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 91bf762..abf70a7 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -62,6 +62,7 @@ obj-$(CONFIG_REGULATOR_MC13892) += mc13892-regulator.o
obj-$(CONFIG_REGULATOR_MC13XXX_CORE) += mc13xxx-regulator-core.o
obj-$(CONFIG_REGULATOR_MT6397) += mt6397-regulator.o
obj-$(CONFIG_REGULATOR_QCOM_RPM) += qcom_rpm-regulator.o
+obj-$(CONFIG_REGULATOR_QCOM_SMD_RPM) += qcom_smd-regulator.o
obj-$(CONFIG_REGULATOR_QCOM_SPMI) += qcom_spmi-regulator.o
obj-$(CONFIG_REGULATOR_PALMAS) += palmas-regulator.o
obj-$(CONFIG_REGULATOR_PFUZE100) += pfuze100-regulator.o
diff --git a/drivers/regulator/qcom_smd-regulator.c b/drivers/regulator/qcom_smd-regulator.c
new file mode 100644
index 0000000..d1efc8c
--- /dev/null
+++ b/drivers/regulator/qcom_smd-regulator.c
@@ -0,0 +1,350 @@
+/*
+ * Copyright (c) 2015, Sony Mobile Communications AB.
+ * Copyright (c) 2012-2013, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/of_regulator.h>
+#include <linux/mfd/qcom-smd-rpm.h>
+#include <dt-bindings/mfd/qcom-smd-rpm.h>
+
+struct qcom_rpm_reg {
+ struct device *dev;
+
+ struct qcom_smd_rpm *rpm;
+
+ u32 type;
+ u32 id;
+
+ struct regulator_desc desc;
+
+ int is_enabled;
+ int uV;
+};
+
+struct rpm_regulator_req {
+ u32 key;
+ u32 nbytes;
+ u32 value;
+};
+
+#define RPM_KEY_SWEN 0x6e657773 /* "swen" */
+#define RPM_KEY_UV 0x00007675 /* "uv" */
+#define RPM_KEY_MA 0x0000616d /* "ma" */
+
+static int rpm_reg_write_active(struct qcom_rpm_reg *vreg,
+ struct rpm_regulator_req *req,
+ size_t size)
+{
+ return qcom_rpm_smd_write(vreg->rpm,
+ QCOM_SMD_RPM_ACTIVE_STATE,
+ vreg->type,
+ vreg->id,
+ req, size);
+}
+
+static int rpm_reg_enable(struct regulator_dev *rdev)
+{
+ struct qcom_rpm_reg *vreg = rdev_get_drvdata(rdev);
+ struct rpm_regulator_req req;
+ int ret;
+
+ req.key = RPM_KEY_SWEN;
+ req.nbytes = sizeof(u32);
+ req.value = 1;
+
+ ret = rpm_reg_write_active(vreg, &req, sizeof(req));
+ if (!ret)
+ vreg->is_enabled = 1;
+
+ return ret;
+}
+
+static int rpm_reg_is_enabled(struct regulator_dev *rdev)
+{
+ struct qcom_rpm_reg *vreg = rdev_get_drvdata(rdev);
+
+ return vreg->is_enabled;
+}
+
+static int rpm_reg_disable(struct regulator_dev *rdev)
+{
+ struct qcom_rpm_reg *vreg = rdev_get_drvdata(rdev);
+ struct rpm_regulator_req req;
+ int ret;
+
+ req.key = RPM_KEY_SWEN;
+ req.nbytes = sizeof(u32);
+ req.value = 0;
+
+ ret = rpm_reg_write_active(vreg, &req, sizeof(req));
+ if (!ret)
+ vreg->is_enabled = 0;
+
+ return ret;
+}
+
+static int rpm_reg_get_voltage(struct regulator_dev *rdev)
+{
+ struct qcom_rpm_reg *vreg = rdev_get_drvdata(rdev);
+
+ return vreg->uV;
+}
+
+static int rpm_reg_set_voltage(struct regulator_dev *rdev,
+ int min_uV,
+ int max_uV,
+ unsigned *selector)
+{
+ struct qcom_rpm_reg *vreg = rdev_get_drvdata(rdev);
+ struct rpm_regulator_req req;
+ int ret = 0;
+
+ req.key = RPM_KEY_UV;
+ req.nbytes = sizeof(u32);
+ req.value = min_uV;
+
+ ret = rpm_reg_write_active(vreg, &req, sizeof(req));
+ if (!ret)
+ vreg->uV = min_uV;
+
+ return ret;
+}
+
+static int rpm_reg_set_load(struct regulator_dev *rdev, int load_uA)
+{
+ struct qcom_rpm_reg *vreg = rdev_get_drvdata(rdev);
+ struct rpm_regulator_req req;
+
+ req.key = RPM_KEY_MA;
+ req.nbytes = sizeof(u32);
+ req.value = load_uA;
+
+ return rpm_reg_write_active(vreg, &req, sizeof(req));
+}
+
+static const struct regulator_ops rpm_smps_ldo_ops = {
+ .enable = rpm_reg_enable,
+ .disable = rpm_reg_disable,
+ .is_enabled = rpm_reg_is_enabled,
+
+ .get_voltage = rpm_reg_get_voltage,
+ .set_voltage = rpm_reg_set_voltage,
+
+ .set_load = rpm_reg_set_load,
+};
+
+static const struct regulator_ops rpm_switch_ops = {
+ .enable = rpm_reg_enable,
+ .disable = rpm_reg_disable,
+ .is_enabled = rpm_reg_is_enabled,
+};
+
+static const struct regulator_desc pm8x41_hfsmps = {
+ .linear_ranges = (struct regulator_linear_range[]) {
+ REGULATOR_LINEAR_RANGE( 375000, 0, 95, 12500),
+ REGULATOR_LINEAR_RANGE(1550000, 96, 158, 25000),
+ },
+ .n_linear_ranges = 2,
+ .n_voltages = 159,
+ .ops = &rpm_smps_ldo_ops,
+};
+
+static const struct regulator_desc pm8841_ftsmps = {
+ .linear_ranges = (struct regulator_linear_range[]) {
+ REGULATOR_LINEAR_RANGE(350000, 0, 184, 5000),
+ REGULATOR_LINEAR_RANGE(700000, 185, 339, 10000),
+ },
+ .n_linear_ranges = 2,
+ .n_voltages = 340,
+ .ops = &rpm_smps_ldo_ops,
+};
+
+static const struct regulator_desc pm8941_boost = {
+ .linear_ranges = (struct regulator_linear_range[]) {
+ REGULATOR_LINEAR_RANGE(4000000, 0, 15, 100000),
+ },
+ .n_linear_ranges = 1,
+ .n_voltages = 16,
+ .ops = &rpm_smps_ldo_ops,
+};
+
+static const struct regulator_desc pm8941_pldo = {
+ .linear_ranges = (struct regulator_linear_range[]) {
+ REGULATOR_LINEAR_RANGE( 750000, 0, 30, 25000),
+ REGULATOR_LINEAR_RANGE(1500000, 31, 99, 50000),
+ },
+ .n_linear_ranges = 2,
+ .n_voltages = 100,
+ .ops = &rpm_smps_ldo_ops,
+};
+
+static const struct regulator_desc pm8941_nldo = {
+ .linear_ranges = (struct regulator_linear_range[]) {
+ REGULATOR_LINEAR_RANGE(750000, 0, 63, 12500),
+ },
+ .n_linear_ranges = 1,
+ .n_voltages = 64,
+ .ops = &rpm_smps_ldo_ops,
+};
+
+static const struct regulator_desc pm8941_lnldo = {
+ .fixed_uV = 1740000,
+ .ops = &rpm_smps_ldo_ops,
+};
+
+static const struct regulator_desc pm8941_switch = {
+ .ops = &rpm_switch_ops,
+};
+
+struct rpm_regulator_data {
+ const char *name;
+ u32 type;
+ u32 id;
+ const struct regulator_desc *desc;
+ const char *supply;
+};
+
+static const struct rpm_regulator_data rpm_pm8841_regulators[] = {
+ { "s1", QCOM_SMD_RPM_SMPB, 1, &pm8x41_hfsmps, "vdd_s1" },
+ { "s2", QCOM_SMD_RPM_SMPB, 2, &pm8841_ftsmps, "vdd_s2" },
+ { "s3", QCOM_SMD_RPM_SMPB, 3, &pm8x41_hfsmps, "vdd_s3" },
+ { "s4", QCOM_SMD_RPM_SMPB, 4, &pm8841_ftsmps, "vdd_s4" },
+ { "s5", QCOM_SMD_RPM_SMPB, 5, &pm8841_ftsmps, "vdd_s5" },
+ { "s6", QCOM_SMD_RPM_SMPB, 6, &pm8841_ftsmps, "vdd_s6" },
+ { "s7", QCOM_SMD_RPM_SMPB, 7, &pm8841_ftsmps, "vdd_s7" },
+ { "s8", QCOM_SMD_RPM_SMPB, 8, &pm8841_ftsmps, "vdd_s8" },
+ {}
+};
+
+static const struct rpm_regulator_data rpm_pm8941_regulators[] = {
+ { "s1", QCOM_SMD_RPM_SMPA, 1, &pm8x41_hfsmps, "vdd_s1" },
+ { "s2", QCOM_SMD_RPM_SMPA, 2, &pm8x41_hfsmps, "vdd_s2" },
+ { "s3", QCOM_SMD_RPM_SMPA, 3, &pm8x41_hfsmps, "vdd_s3" },
+ { "s4", QCOM_SMD_RPM_BOOST, 1, &pm8941_boost },
+
+ { "l1", QCOM_SMD_RPM_LDOA, 1, &pm8941_nldo, "vdd_l1_l3" },
+ { "l2", QCOM_SMD_RPM_LDOA, 2, &pm8941_nldo, "vdd_l2_lvs1_2_3" },
+ { "l3", QCOM_SMD_RPM_LDOA, 3, &pm8941_nldo, "vdd_l1_l3" },
+ { "l4", QCOM_SMD_RPM_LDOA, 4, &pm8941_nldo, "vdd_l4_l11" },
+ { "l5", QCOM_SMD_RPM_LDOA, 5, &pm8941_lnldo, "vdd_l5_l7" },
+ { "l6", QCOM_SMD_RPM_LDOA, 6, &pm8941_pldo, "vdd_l6_l12_l14_l15" },
+ { "l7", QCOM_SMD_RPM_LDOA, 7, &pm8941_lnldo, "vdd_l5_l7" },
+ { "l8", QCOM_SMD_RPM_LDOA, 8, &pm8941_pldo, "vdd_l8_l16_l18_l19" },
+ { "l9", QCOM_SMD_RPM_LDOA, 9, &pm8941_pldo, "vdd_l9_l10_l17_l22" },
+ { "l10", QCOM_SMD_RPM_LDOA, 10, &pm8941_pldo, "vdd_l9_l10_l17_l22" },
+ { "l11", QCOM_SMD_RPM_LDOA, 11, &pm8941_nldo, "vdd_l4_l11" },
+ { "l12", QCOM_SMD_RPM_LDOA, 12, &pm8941_pldo, "vdd_l6_l12_l14_l15" },
+ { "l13", QCOM_SMD_RPM_LDOA, 13, &pm8941_pldo, "vdd_l13_l20_l23_l24" },
+ { "l14", QCOM_SMD_RPM_LDOA, 14, &pm8941_pldo, "vdd_l6_l12_l14_l15" },
+ { "l15", QCOM_SMD_RPM_LDOA, 15, &pm8941_pldo, "vdd_l6_l12_l14_l15" },
+ { "l16", QCOM_SMD_RPM_LDOA, 16, &pm8941_pldo, "vdd_l8_l16_l18_l19" },
+ { "l17", QCOM_SMD_RPM_LDOA, 17, &pm8941_pldo, "vdd_l9_l10_l17_l22" },
+ { "l18", QCOM_SMD_RPM_LDOA, 18, &pm8941_pldo, "vdd_l8_l16_l18_l19" },
+ { "l19", QCOM_SMD_RPM_LDOA, 19, &pm8941_pldo, "vdd_l8_l16_l18_l19" },
+ { "l20", QCOM_SMD_RPM_LDOA, 20, &pm8941_pldo, "vdd_l13_l20_l23_l24" },
+ { "l21", QCOM_SMD_RPM_LDOA, 21, &pm8941_pldo, "vdd_l21" },
+ { "l22", QCOM_SMD_RPM_LDOA, 22, &pm8941_pldo, "vdd_l9_l10_l17_l22" },
+ { "l23", QCOM_SMD_RPM_LDOA, 23, &pm8941_pldo, "vdd_l13_l20_l23_l24" },
+ { "l24", QCOM_SMD_RPM_LDOA, 24, &pm8941_pldo, "vdd_l13_l20_l23_l24" },
+
+ { "lvs1", QCOM_SMD_RPM_VSA, 1, &pm8941_switch, "vdd_l2_lvs1_2_3" },
+ { "lvs2", QCOM_SMD_RPM_VSA, 2, &pm8941_switch, "vdd_l2_lvs1_2_3" },
+ { "lvs3", QCOM_SMD_RPM_VSA, 3, &pm8941_switch, "vdd_l2_lvs1_2_3" },
+
+ { "5vs1", QCOM_SMD_RPM_VSA, 4, &pm8941_switch, "vin_5vs" },
+ { "5vs2", QCOM_SMD_RPM_VSA, 5, &pm8941_switch, "vin_5vs" },
+
+ {}
+};
+
+static const struct of_device_id rpm_of_match[] = {
+ { .compatible = "qcom,rpm-pm8841-regulators", .data = &rpm_pm8841_regulators },
+ { .compatible = "qcom,rpm-pm8941-regulators", .data = &rpm_pm8941_regulators },
+ {}
+};
+MODULE_DEVICE_TABLE(of, rpm_of_match);
+
+static int rpm_reg_probe(struct platform_device *pdev)
+{
+ const struct rpm_regulator_data *reg;
+ const struct of_device_id *match;
+ struct regulator_config config = { };
+ struct regulator_dev *rdev;
+ struct qcom_rpm_reg *vreg;
+ struct qcom_smd_rpm *rpm;
+
+ rpm = dev_get_drvdata(pdev->dev.parent);
+ if (!rpm) {
+ dev_err(&pdev->dev, "unable to retrieve handle to rpm\n");
+ return -ENODEV;
+ }
+
+ match = of_match_device(rpm_of_match, &pdev->dev);
+ for (reg = match->data; reg->name; reg++) {
+ vreg = devm_kzalloc(&pdev->dev, sizeof(*vreg), GFP_KERNEL);
+ if (!vreg)
+ return -ENOMEM;
+
+ vreg->dev = &pdev->dev;
+ vreg->type = reg->type;
+ vreg->id = reg->id;
+ vreg->rpm = rpm;
+
+ memcpy(&vreg->desc, reg->desc, sizeof(vreg->desc));
+
+ vreg->desc.id = -1;
+ vreg->desc.owner = THIS_MODULE;
+ vreg->desc.type = REGULATOR_VOLTAGE;
+ vreg->desc.name = reg->name;
+ vreg->desc.supply_name = reg->supply;
+ vreg->desc.of_match = reg->name;
+
+ config.dev = &pdev->dev;
+ config.driver_data = vreg;
+ rdev = devm_regulator_register(&pdev->dev, &vreg->desc, &config);
+ if (IS_ERR(rdev)) {
+ dev_err(&pdev->dev, "failed to register %s\n", reg->name);
+ return PTR_ERR(rdev);
+ }
+ }
+
+ return 0;
+}
+
+static struct platform_driver rpm_reg_driver = {
+ .probe = rpm_reg_probe,
+ .driver = {
+ .name = "qcom_rpm_smd_regulator",
+ .of_match_table = rpm_of_match,
+ },
+};
+
+static int __init rpm_reg_init(void)
+{
+ return platform_driver_register(&rpm_reg_driver);
+}
+subsys_initcall(rpm_reg_init);
+
+static void __exit rpm_reg_exit(void)
+{
+ platform_driver_unregister(&rpm_reg_driver);
+}
+module_exit(rpm_reg_exit)
+
+MODULE_DESCRIPTION("Qualcomm RPM regulator driver");
+MODULE_LICENSE("GPL v2");
--
1.9.3 (Apple Git-50)
^ permalink raw reply related [flat|nested] 39+ messages in thread* [PATCH v2 08/11] ARM: dts: msm8974: Add tcsr mutex node
2015-06-26 21:50 [PATCH v2 00/11] Qualcomm Shared Memory & RPM drivers bjorn
` (6 preceding siblings ...)
2015-06-26 21:50 ` [PATCH v2 07/11] regulator: qcom: smd: Regulator driver for the Qualcomm RPM bjorn
@ 2015-06-26 21:50 ` bjorn
[not found] ` <1435355419-23602-9-git-send-email-bjorn.andersson-/MT0OVThwyLZJqsBc5GL+g@public.gmane.org>
2015-06-26 21:50 ` [PATCH v2 09/11] ARM: dts: msm8974: Add smem reservation and node bjorn
` (2 subsequent siblings)
10 siblings, 1 reply; 39+ messages in thread
From: bjorn @ 2015-06-26 21:50 UTC (permalink / raw)
To: Andy Gross
Cc: Mark Rutland, devicetree, Pawel Moll, Ian Campbell,
linux-arm-msm, linux-kernel, Rob Herring, Kumar Gala,
linux-arm-kernel
From: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
---
arch/arm/boot/dts/qcom-msm8974.dtsi | 12 ++++++++++++
1 file changed, 12 insertions(+)
diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
index 37b47b5..7c7b7dc 100644
--- a/arch/arm/boot/dts/qcom-msm8974.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
@@ -220,6 +220,11 @@
reg = <0xfc400000 0x4000>;
};
+ tcsr_mutex_block: syscon@fd484000 {
+ compatible = "syscon";
+ reg = <0xfd484000 0x2000>;
+ };
+
mmcc: clock-controller@fd8c0000 {
compatible = "qcom,mmcc-msm8974";
#clock-cells = <1>;
@@ -227,6 +232,13 @@
reg = <0xfd8c0000 0x6000>;
};
+ tcsr_mutex: tcsr-mutex {
+ compatible = "qcom,tcsr-mutex";
+ syscon = <&tcsr_mutex_block 0 0x80>;
+
+ #hwlock-cells = <1>;
+ };
+
serial@f991e000 {
compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
reg = <0xf991e000 0x1000>;
--
1.9.3 (Apple Git-50)
^ permalink raw reply related [flat|nested] 39+ messages in thread* [PATCH v2 09/11] ARM: dts: msm8974: Add smem reservation and node
2015-06-26 21:50 [PATCH v2 00/11] Qualcomm Shared Memory & RPM drivers bjorn
` (7 preceding siblings ...)
2015-06-26 21:50 ` [PATCH v2 08/11] ARM: dts: msm8974: Add tcsr mutex node bjorn
@ 2015-06-26 21:50 ` bjorn
2015-07-23 20:51 ` Andy Gross
2015-06-26 21:50 ` [PATCH v2 10/11] ARM: dts: msm8974: Add smd, rpm and regulator nodes bjorn
2015-06-26 21:50 ` [PATCH v2 11/11] ARM: dts: xperia-honami: Add regulator nodes for Honami bjorn
10 siblings, 1 reply; 39+ messages in thread
From: bjorn @ 2015-06-26 21:50 UTC (permalink / raw)
To: Andy Gross
Cc: Mark Rutland, devicetree, Pawel Moll, Ian Campbell,
linux-arm-msm, linux-kernel, Rob Herring, Kumar Gala,
linux-arm-kernel
From: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
---
arch/arm/boot/dts/qcom-msm8974.dtsi | 20 ++++++++++++++++++++
1 file changed, 20 insertions(+)
diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
index 7c7b7dc..d7c99b8 100644
--- a/arch/arm/boot/dts/qcom-msm8974.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
@@ -9,6 +9,17 @@
compatible = "qcom,msm8974";
interrupt-parent = <&intc>;
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ smem_region: smem@fa00000 {
+ reg = <0xfa00000 0x200000>;
+ no-map;
+ };
+ };
+
cpus {
#address-cells = <1>;
#size-cells = <0>;
@@ -239,6 +250,15 @@
#hwlock-cells = <1>;
};
+ smem@fa00000 {
+ compatible = "qcom,smem";
+
+ memory-region = <&smem_region>;
+ reg = <0xfc428000 0x4000>;
+
+ hwlocks = <&tcsr_mutex 3>;
+ };
+
serial@f991e000 {
compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
reg = <0xf991e000 0x1000>;
--
1.9.3 (Apple Git-50)
^ permalink raw reply related [flat|nested] 39+ messages in thread* Re: [PATCH v2 09/11] ARM: dts: msm8974: Add smem reservation and node
2015-06-26 21:50 ` [PATCH v2 09/11] ARM: dts: msm8974: Add smem reservation and node bjorn
@ 2015-07-23 20:51 ` Andy Gross
0 siblings, 0 replies; 39+ messages in thread
From: Andy Gross @ 2015-07-23 20:51 UTC (permalink / raw)
To: bjorn
Cc: Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
devicetree, linux-arm-kernel, linux-kernel, linux-arm-msm
On Fri, Jun 26, 2015 at 02:50:17PM -0700, bjorn@kryo.se wrote:
> From: Bjorn Andersson <bjorn.andersson@sonymobile.com>
>
> Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
> ---
Applied, thanks.
--
Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply [flat|nested] 39+ messages in thread
* [PATCH v2 10/11] ARM: dts: msm8974: Add smd, rpm and regulator nodes
2015-06-26 21:50 [PATCH v2 00/11] Qualcomm Shared Memory & RPM drivers bjorn
` (8 preceding siblings ...)
2015-06-26 21:50 ` [PATCH v2 09/11] ARM: dts: msm8974: Add smem reservation and node bjorn
@ 2015-06-26 21:50 ` bjorn
2015-06-26 21:50 ` [PATCH v2 11/11] ARM: dts: xperia-honami: Add regulator nodes for Honami bjorn
10 siblings, 0 replies; 39+ messages in thread
From: bjorn @ 2015-06-26 21:50 UTC (permalink / raw)
To: Andy Gross
Cc: Mark Rutland, devicetree, Pawel Moll, Ian Campbell,
linux-arm-msm, linux-kernel, Rob Herring, Kumar Gala,
linux-arm-kernel
From: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
---
arch/arm/boot/dts/qcom-msm8974.dtsi | 74 +++++++++++++++++++++++++++++++++++++
1 file changed, 74 insertions(+)
diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
index d7c99b8..65f5496 100644
--- a/arch/arm/boot/dts/qcom-msm8974.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
@@ -114,6 +114,11 @@
<0xf9002000 0x1000>;
};
+ apcs: syscon@f9011000 {
+ compatible = "syscon";
+ reg = <0xf9011000 0x1000>;
+ };
+
timer@f9020000 {
#address-cells = <1>;
#size-cells = <1>;
@@ -334,4 +339,73 @@
#interrupt-cells = <4>;
};
};
+
+ smd {
+ compatible = "qcom,smd";
+
+ rpm {
+ interrupts = <0 168 1>;
+ qcom,ipc = <&apcs 8 0>;
+ qcom,smd-edge = <15>;
+
+ rpm_requests {
+ compatible = "qcom,rpm-msm8974";
+ qcom,smd-channels = "rpm_requests";
+
+ pm8841-regulators {
+ compatible = "qcom,rpm-pm8841-regulators";
+
+ pm8841_s1: s1 {};
+ pm8841_s2: s2 {};
+ pm8841_s3: s3 {};
+ pm8841_s4: s4 {};
+ pm8841_s5: s5 {};
+ pm8841_s6: s6 {};
+ pm8841_s7: s7 {};
+ pm8841_s8: s8 {};
+ };
+
+ pm8941-regulators {
+ compatible = "qcom,rpm-pm8941-regulators";
+
+ pm8941_s1: s1 {};
+ pm8941_s2: s2 {};
+ pm8941_s3: s3 {};
+ pm8941_5v: s4 {};
+
+ pm8941_l1: l1 {};
+ pm8941_l2: l2 {};
+ pm8941_l3: l3 {};
+ pm8941_l4: l4 {};
+ pm8941_l5: l5 {};
+ pm8941_l6: l6 {};
+ pm8941_l7: l7 {};
+ pm8941_l8: l8 {};
+ pm8941_l9: l9 {};
+ pm8941_l10: l10 {};
+ pm8941_l11: l11 {};
+ pm8941_l12: l12 {};
+ pm8941_l13: l13 {};
+ pm8941_l14: l14 {};
+ pm8941_l15: l15 {};
+ pm8941_l16: l16 {};
+ pm8941_l17: l17 {};
+ pm8941_l18: l18 {};
+ pm8941_l19: l19 {};
+ pm8941_l20: l20 {};
+ pm8941_l21: l21 {};
+ pm8941_l22: l22 {};
+ pm8941_l23: l23 {};
+ pm8941_l24: l24 {};
+
+ pm8941_lvs1: lvs1 {};
+ pm8941_lvs2: lvs2 {};
+ pm8941_lvs3: lvs3 {};
+
+ pm8941_5vs1: 5vs1 {};
+ pm8941_5vs2: 5vs2 {};
+ };
+ };
+ };
+ };
};
--
1.9.3 (Apple Git-50)
^ permalink raw reply related [flat|nested] 39+ messages in thread* [PATCH v2 11/11] ARM: dts: xperia-honami: Add regulator nodes for Honami
2015-06-26 21:50 [PATCH v2 00/11] Qualcomm Shared Memory & RPM drivers bjorn
` (9 preceding siblings ...)
2015-06-26 21:50 ` [PATCH v2 10/11] ARM: dts: msm8974: Add smd, rpm and regulator nodes bjorn
@ 2015-06-26 21:50 ` bjorn
10 siblings, 0 replies; 39+ messages in thread
From: bjorn @ 2015-06-26 21:50 UTC (permalink / raw)
To: Andy Gross
Cc: Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
devicetree, linux-arm-kernel, linux-kernel, linux-arm-msm
From: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
---
.../boot/dts/qcom-msm8974-sony-xperia-honami.dts | 199 +++++++++++++++++++++
1 file changed, 199 insertions(+)
diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts
index bd35b06..49605ca 100644
--- a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts
+++ b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts
@@ -10,10 +10,209 @@
reg = <0 0x40000000>, <0x40000000 0x40000000>;
device_type = "memory";
};
+
+ smd {
+ rpm {
+ rpm_requests {
+ pm8941-regulators {
+ vdd_l1_l3-supply = <&pm8941_s1>;
+ vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+ vdd_l4_l11-supply = <&pm8941_s1>;
+ vdd_l5_l7-supply = <&pm8941_s2>;
+ vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+ vdd_l9_l10_l17_l22-supply = <&vreg_boost_bypass>;
+ vdd_l13_l20_l23_l24-supply = <&vreg_boost_bypass>;
+ vdd_l21-supply = <&vreg_boost_bypass>;
+ vin_5vs-supply = <&pm8941_5v>;
+
+ s1 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ s2 {
+ regulator-min-microvolt = <2150000>;
+ regulator-max-microvolt = <2150000>;
+ regulator-boot-on;
+ };
+
+ s3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ s4 {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ l1 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ l3 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ l4 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };
+
+ l5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ };
+
+ l7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ };
+
+ l8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l9 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ l11 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1350000>;
+ };
+
+ l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ };
+
+ l13 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ regulator-boot-on;
+ };
+
+ l14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l15 {
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
+ };
+
+ l16 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+
+ l17 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+
+ l18 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+
+ l19 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ l20 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ regulator-boot-on;
+ };
+
+ l21 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ regulator-boot-on;
+ };
+
+ l22 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ l23 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ l24 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;
+ regulator-boot-on;
+ };
+ };
+ };
+ };
+ };
+
+ vreg_boost_bypass: vreg-boost-bypass {
+ compatible = "regulator-fixed";
+
+ regulator-name = "vreg-boost-bypass";
+ regulator-min-microvolt = <3150000>;
+ regulator-max-microvolt = <3150000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+
+ gpio = <&pm8941_gpios 21 0>;
+ enable-active-high;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&boost_bypass_en>;
+
+ };
};
&soc {
serial@f991e000 {
status = "ok";
};
+
+};
+
+&spmi_bus {
+ pm8941@0 {
+ gpios@c000 {
+ boost_bypass_en: boost-bypass-en {
+ always-on {
+ pins = "gpio21";
+ function = "normal";
+ };
+ };
+ };
+ };
};
--
1.9.3 (Apple Git-50)
^ permalink raw reply related [flat|nested] 39+ messages in thread