linux-arm-msm.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Rajendra Nayak <rnayak@codeaurora.org>
To: agross@kernel.org, bjorn.andersson@linaro.org, robh+dt@kernel.org
Cc: linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org,
	Rajendra Nayak <rnayak@codeaurora.org>
Subject: [PATCH 03/13] arm64: dts: sc7280: Add basic dts/dtsi files for SC7280 soc
Date: Fri, 12 Feb 2021 12:58:40 +0530	[thread overview]
Message-ID: <1613114930-1661-4-git-send-email-rnayak@codeaurora.org> (raw)
In-Reply-To: <1613114930-1661-1-git-send-email-rnayak@codeaurora.org>

Add initial device tree support for the SC7280 SoC and the IDP
boards based on this SoC

Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
---
 arch/arm64/boot/dts/qcom/Makefile       |   1 +
 arch/arm64/boot/dts/qcom/sc7280-idp.dts |  47 +++++
 arch/arm64/boot/dts/qcom/sc7280.dtsi    | 294 ++++++++++++++++++++++++++++++++
 3 files changed, 342 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/sc7280-idp.dts
 create mode 100644 arch/arm64/boot/dts/qcom/sc7280.dtsi

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 5113fac..6f16ff6 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -32,6 +32,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-lazor-r3-kb.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-lazor-r3-lte.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-r1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-r1-lte.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-idp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm630-sony-xperia-ganges-kirin.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm630-sony-xperia-nile-discovery.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm630-sony-xperia-nile-pioneer.dtb
diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dts b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
new file mode 100644
index 0000000..428f863
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
@@ -0,0 +1,47 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * sc7280 IDP board device tree source
+ *
+ * Copyright (c) 2021, The Linux Foundation. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include "sc7280.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. SC7280 IDP platform";
+	compatible = "qcom,sc7280-idp";
+
+	aliases {
+		serial0 = &uart5;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&qupv3_id_0 {
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
+
+/* PINCTRL - additions to nodes defined in sc7280.dtsi */
+
+&qup_uart5_default {
+	tx {
+		pins = "gpio46";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	rx {
+		pins = "gpio47";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
new file mode 100644
index 0000000..1fe2eba
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -0,0 +1,294 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * sc7280 SoC device tree source
+ *
+ * Copyright (c) 2020-2021, The Linux Foundation. All rights reserved.
+ */
+
+#include <dt-bindings/clock/qcom,gcc-sc7280.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	interrupt-parent = <&intc>;
+
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	chosen { };
+
+	clocks {
+		xo_board: xo-board {
+			compatible = "fixed-clock";
+			clock-frequency = <76800000>;
+			#clock-cells = <0>;
+		};
+
+		sleep_clk: sleep-clk {
+			compatible = "fixed-clock";
+			clock-frequency = <32000>;
+			#clock-cells = <0>;
+		};
+	};
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		CPU0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,kryo";
+			reg = <0x0 0x0>;
+			enable-method = "psci";
+			next-level-cache = <&L2_0>;
+			L2_0: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+				L3_0: l3-cache {
+					compatible = "cache";
+				};
+			};
+		};
+
+		CPU1: cpu@100 {
+			device_type = "cpu";
+			compatible = "arm,kryo";
+			reg = <0x0 0x100>;
+			enable-method = "psci";
+			next-level-cache = <&L2_100>;
+			L2_100: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU2: cpu@200 {
+			device_type = "cpu";
+			compatible = "arm,kryo";
+			reg = <0x0 0x200>;
+			enable-method = "psci";
+			next-level-cache = <&L2_200>;
+			L2_200: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU3: cpu@300 {
+			device_type = "cpu";
+			compatible = "arm,kryo";
+			reg = <0x0 0x300>;
+			enable-method = "psci";
+			next-level-cache = <&L2_300>;
+			L2_300: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU4: cpu@400 {
+			device_type = "cpu";
+			compatible = "arm,kryo";
+			reg = <0x0 0x400>;
+			enable-method = "psci";
+			next-level-cache = <&L2_400>;
+			L2_400: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU5: cpu@500 {
+			device_type = "cpu";
+			compatible = "arm,kryo";
+			reg = <0x0 0x500>;
+			enable-method = "psci";
+			next-level-cache = <&L2_500>;
+			L2_500: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU6: cpu@600 {
+			device_type = "cpu";
+			compatible = "arm,kryo";
+			reg = <0x0 0x600>;
+			enable-method = "psci";
+			next-level-cache = <&L2_600>;
+			L2_600: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU7: cpu@700 {
+			device_type = "cpu";
+			compatible = "arm,kryo";
+			reg = <0x0 0x700>;
+			enable-method = "psci";
+			next-level-cache = <&L2_700>;
+			L2_700: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		/* We expect the bootloader to fill in the size */
+		reg = <0 0x80000000 0 0>;
+	};
+
+	firmware {
+		scm {
+			compatible = "qcom,scm-sc7280", "qcom,scm";
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	soc: soc {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges = <0 0 0 0 0x10 0>;
+		dma-ranges = <0 0 0 0 0x10 0>;
+		compatible = "simple-bus";
+
+		gcc: clock-controller@100000 {
+			compatible = "qcom,gcc-sc7280";
+			reg = <0 0x00100000 0 0x1f0000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+		};
+
+		qupv3_id_0: geniqup@9c0000 {
+			compatible = "qcom,geni-se-qup";
+			reg = <0 0x009c0000 0 0x2000>;
+			clock-names = "m-ahb", "s-ahb";
+			clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
+				 <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			status = "disabled";
+
+			uart5: serial@994000 {
+				compatible = "qcom,geni-debug-uart";
+				reg = <0 0x00994000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart5_default>;
+				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+				status = "disabled";
+			};
+		};
+
+		tlmm: pinctrl@f100000 {
+			compatible = "qcom,sc7280-pinctrl";
+			reg = <0 0xf100000 0 0x1000000>;
+			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			gpio-ranges = <&tlmm 0 0 175>;
+
+			qup_uart5_default: qup-uart5-default {
+				pins = "gpio46", "gpio47";
+				function = "qup13";
+			};
+		};
+
+		intc: interrupt-controller@17a00000 {
+			compatible = "arm,gic-v3";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			reg = <0 0x17a00000 0 0x10000>,     /* GICD */
+			      <0 0x17a60000 0 0x100000>;    /* GICR * 8 */
+			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_LOW>;
+
+			gic-its@17a40000 {
+				compatible = "arm,gic-v3-its";
+				msi-controller;
+				#msi-cells = <1>;
+				reg = <0 0x17a40000 0 0x20000>;
+				status = "disabled";
+			};
+		};
+
+		timer@17c20000 {
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			compatible = "arm,armv7-timer-mem";
+			reg = <0 0x17c20000 0 0x1000>;
+
+			frame@17c21000 {
+				frame-number = <0>;
+				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0 0x17c21000 0 0x1000>,
+				      <0 0x17c22000 0 0x1000>;
+			};
+
+			frame@17c23000 {
+				frame-number = <1>;
+				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0 0x17c23000 0 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17c25000 {
+				frame-number = <2>;
+				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0 0x17c25000 0 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17c27000 {
+				frame-number = <3>;
+				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0 0x17c27000 0 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17c29000 {
+				frame-number = <4>;
+				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0 0x17c29000 0 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17c2b000 {
+				frame-number = <5>;
+				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0 0x17c2b000 0 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17c2d000 {
+				frame-number = <6>;
+				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0 0x17c2d000 0 0x1000>;
+				status = "disabled";
+			};
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation


  parent reply	other threads:[~2021-02-12  7:33 UTC|newest]

Thread overview: 38+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-02-12  7:28 [PATCH 00/13] Add binding updates and DT files for SC7280 SoC Rajendra Nayak
2021-02-12  7:28 ` [PATCH 01/13] dt-bindings: arm: qcom: Document SC7280 SoC and board Rajendra Nayak
2021-02-23  7:49   ` Stephen Boyd
2021-03-05 20:08   ` Rob Herring
2021-02-12  7:28 ` [PATCH 02/13] dt-bindings: firmware: scm: Add SC7280 support Rajendra Nayak
2021-02-23  7:50   ` Stephen Boyd
2021-03-05 20:08   ` Rob Herring
2021-02-12  7:28 ` Rajendra Nayak [this message]
2021-02-23  7:37   ` [PATCH 03/13] arm64: dts: sc7280: Add basic dts/dtsi files for SC7280 soc Stephen Boyd
2021-02-23 11:42     ` Rajendra Nayak
2021-02-12  7:28 ` [PATCH 04/13] dt-bindings: qcom,pdc: Add compatible for sc7280 Rajendra Nayak
2021-02-23  7:38   ` Stephen Boyd
2021-02-23  7:39   ` Stephen Boyd
2021-03-05  5:46     ` Rajendra Nayak
2021-02-12  7:28 ` [PATCH 05/13] arm64: dts: qcom: sc7280: Add RSC and PDC devices Rajendra Nayak
2021-02-23  7:41   ` Stephen Boyd
2021-02-12  7:28 ` [PATCH 06/13] arm64: dts: qcom: SC7280: Add rpmhcc clock controller node Rajendra Nayak
2021-02-23  7:43   ` Stephen Boyd
2021-03-01 17:27     ` Taniya Das
2021-03-03  8:21       ` Stephen Boyd
2021-02-12  7:28 ` [PATCH 07/13] dt-bindings: arm-smmu: Add compatible for SC7280 SoC Rajendra Nayak
2021-02-23  7:43   ` Stephen Boyd
2021-02-12  7:28 ` [PATCH 08/13] arm64: dts: qcom: sc7280: Add device node for APPS SMMU Rajendra Nayak
2021-02-12  7:28 ` [PATCH 09/13] arm64: dts: qcom: Add reserved memory for fw Rajendra Nayak
2021-02-23  7:45   ` Stephen Boyd
2021-02-23 11:45     ` Rajendra Nayak
2021-02-12  7:28 ` [PATCH 10/13] dt-bindings: watchdog: Add compatible for SC7280 SoC Rajendra Nayak
2021-02-23  7:45   ` Stephen Boyd
2021-02-12  7:28 ` [PATCH 11/13] arm64: dts: qcom: sc7280: Add APSS watchdog node Rajendra Nayak
2021-02-23  7:46   ` Stephen Boyd
2021-02-12  7:28 ` [PATCH 12/13] arm64: dts: qcom: sc7280: Add SPMI PMIC arbiter device for SC7280 Rajendra Nayak
2021-02-12  7:28 ` [PATCH 13/13] arm64: dts: qcom: sc7280: Add cpuidle states Rajendra Nayak
2021-02-23  7:49   ` Stephen Boyd
2021-02-23 11:50     ` Maulik Shah
2021-03-11  0:13 ` [PATCH 00/13] Add binding updates and DT files for SC7280 SoC Bjorn Andersson
2021-03-11  9:15   ` Rajendra Nayak
2021-03-11 11:35     ` Rajendra Nayak
2021-03-11 16:44     ` Bjorn Andersson

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1613114930-1661-4-git-send-email-rnayak@codeaurora.org \
    --to=rnayak@codeaurora.org \
    --cc=agross@kernel.org \
    --cc=bjorn.andersson@linaro.org \
    --cc=devicetree@vger.kernel.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=robh+dt@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).