From: Konrad Dybcio <konrad.dybcio@linaro.org>
To: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Cc: Stephan Gerhold <stephan@gerhold.net>,
linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
agross@kernel.org, linux-kernel@vger.kernel.org,
linux-crypto@vger.kernel.org, andersson@kernel.org,
bhupesh.linux@gmail.com, krzysztof.kozlowski@linaro.org,
robh+dt@kernel.org, vladimir.zapolskiy@linaro.org,
rfoss@kernel.org, neil.armstrong@linaro.org, djakov@kernel.org
Subject: Re: [PATCH v6 07/11] arm64: dts: qcom: sm6115: Add Crypto Engine support
Date: Fri, 19 May 2023 12:51:39 +0200 [thread overview]
Message-ID: <875dec34-35da-e427-ae32-598958762dd2@linaro.org> (raw)
In-Reply-To: <CAH=2NtyUNJFMbrhvP9BjmzdsLj9kvSYUH_ueAPUan9GRKaq2Xw@mail.gmail.com>
On 19.05.2023 12:49, Bhupesh Sharma wrote:
> On Fri, 19 May 2023 at 16:12, Konrad Dybcio <konrad.dybcio@linaro.org> wrote:
>>
>> On 19.05.2023 12:22, Bhupesh Sharma wrote:
>>> Hi Stephan,
>>>
>>> On Fri, 19 May 2023 at 15:40, Stephan Gerhold <stephan@gerhold.net> wrote:
>>>>
>>>> Hi Bhupesh,
>>>>
>>>> Not sure if this is the latest version of this series since it's pretty
>>>> old but I didn't find a new one. Just came here because you mentioned
>>>> RB1/RB2 [1] in my bam_dma patch and they don't have any BAM defined
>>>> upstream yet.
>>>>
>>>> [1]: https://lore.kernel.org/linux-arm-msm/CAH=2Ntw0BZH=RGp14mYLhX7D6jV5O5eDKRQbby=uCy85xMDU_g@mail.gmail.com/
>>>>
>>>> On Wed, Apr 05, 2023 at 12:58:32PM +0530, Bhupesh Sharma wrote:
>>>>> Add crypto engine (CE) and CE BAM related nodes and definitions to
>>>>> 'sm6115.dtsi'.
>>>>>
>>>>> Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
>>>>> ---
>>>>> arch/arm64/boot/dts/qcom/sm6115.dtsi | 22 ++++++++++++++++++++++
>>>>> 1 file changed, 22 insertions(+)
>>>>>
>>>>> diff --git a/arch/arm64/boot/dts/qcom/sm6115.dtsi b/arch/arm64/boot/dts/qcom/sm6115.dtsi
>>>>> index 2a51c938bbcb..ebac026b4cc7 100644
>>>>> --- a/arch/arm64/boot/dts/qcom/sm6115.dtsi
>>>>> +++ b/arch/arm64/boot/dts/qcom/sm6115.dtsi
>>>>> @@ -650,6 +650,28 @@ usb_hsphy: phy@1613000 {
>>>>> status = "disabled";
>>>>> };
>>>>>
>>>>> + cryptobam: dma-controller@1b04000 {
>>>>> + compatible = "qcom,bam-v1.7.4", "qcom,bam-v1.7.0";
>>>>> + reg = <0x0 0x01b04000 0x0 0x24000>;
>>>>> + interrupts = <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>;
>>>>> + #dma-cells = <1>;
>>>>> + qcom,ee = <0>;
>>>>> + qcom,controlled-remotely;
>>>>> + num-channels = <8>;
>>>>> + qcom,num-ees = <2>;
>>>>> + iommus = <&apps_smmu 0x94 0x11>,
>>>>> + <&apps_smmu 0x96 0x11>;
>>>>> + };
>>>>> +
>>>>> + crypto: crypto@1b3a000 {
>>>>> + compatible = "qcom,sm6115-qce", "qcom,sm8150-qce", "qcom,qce";
>>>>> + reg = <0x0 0x01b3a000 0x0 0x6000>;
>>>>> + dmas = <&cryptobam 6>, <&cryptobam 7>;
>>>>> + dma-names = "rx", "tx";
>>>>> + iommus = <&apps_smmu 0x94 0x11>,
>>>>> + <&apps_smmu 0x96 0x11>;
>>>>
>>>> Shouldn't you have clocks = <&rpmcc RPM_SMD_CE1_CLK> here to make sure
>>>> the clock for the crypto engine is on? Your binding patch (PATCH 06/11)
>>>> says "Crypto Engine block on Qualcomm SoCs SM6115 and QCM2290 do not
>>>> require clocks strictly" but doesn't say why.
>>>>
>>>> Make sure you don't rely on having rpmcc keep unused clocks on
>>>> permanently. This is the case at the moment, but we would like to change
>>>> this [2]. Adding new users that rely on this broken behavior would just
>>>> make this effort even more complicated.
>>>>
>>>> If you also add the clock to the cryptobam then you should be able to
>>>> see the advantage of my bam_dma patch [3]. It allows you to drop
>>>> "num-channels" and "qcom,num-ees" from the cryptobam in your changes
>>>> above because it can then be read directly from the BAM registers.
>>>
>>> Thanks for pointing this out. Actually that's why I was using your
>>> patch while testing with RB1/RB2 :)
>>>
>>> Yes, so the background is that I am preparing a new version of this
>>> crypto enablement patchset.
>>> Also your assumption about the clocks being turned on by the firmware
>>> is true for RB1/RB2 devices, so enabling them via Linux is optional as
>>> per Qualcomm enggs.
>> This is not necessarily true. Currently it's kept always-on on
>> by clk_smd_rpm_handoff, but that's a hack from 10 years ago when smd
>> was still new.
>>
>>>
>>> So, I am testing the new patchset right now with 'clock' entries
>>> provided in the .dtsi and see if that causes any issue / improvement
>>> (etc.)
>> It won't change since it's on anyway, but that won't be a given for long.
>
> Right, so that's what I observe: RPM_SMD_CE1_CLK is always on by the
> time crypto _probe gets called.
> So, IMO let's not mix this patchset with the other fix which probably
> will fix the 10-year old clk_smd_rpm handoff keeping
> these clocks on.
>
> Probably that should be a separate changeset - requiring very thorough
> checks to make sure that we don't break
> working platforms.
It's not about mixing patchsets, the nodes should reflect all the clock/
power-domain/regulator/pinctrl/etc. dependencies from their introduction.
Remember, dt describes the hardware, not the software or firmware.
That - among other things - ensures backwards compatibility can be
preserved.
>
> Thanks.
next prev parent reply other threads:[~2023-05-19 10:51 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-04-05 7:28 [PATCH v6 00/11] arm64: qcom: Enable Crypto Engine for a few Qualcomm SoCs Bhupesh Sharma
2023-04-05 7:28 ` [PATCH v6 01/11] dt-bindings: dma: Add support for SM6115 and QCM2290 SoCs Bhupesh Sharma
2023-04-05 7:28 ` [PATCH v6 02/11] dt-bindings: dma: Increase iommu maxItems for BAM DMA Bhupesh Sharma
2023-04-05 7:28 ` [PATCH v6 03/11] arm64: dts: qcom: sdm8550: Fix the BAM DMA engine compatible string Bhupesh Sharma
2023-04-05 7:28 ` [PATCH v6 04/11] arm64: dts: qcom: sdm845: Fix the slimbam " Bhupesh Sharma
2023-04-05 7:28 ` [PATCH v6 05/11] dt-bindings: qcom-qce: Fix compatible combinations for SM8150 and IPQ4019 SoCs Bhupesh Sharma
2023-04-12 13:23 ` Rob Herring
2023-04-05 7:28 ` [PATCH v6 06/11] dt-bindings: qcom-qce: Add compatibles for SM6115 and QCM2290 Bhupesh Sharma
2023-04-05 7:28 ` [PATCH v6 07/11] arm64: dts: qcom: sm6115: Add Crypto Engine support Bhupesh Sharma
2023-04-06 13:52 ` Konrad Dybcio
2023-05-19 10:10 ` Stephan Gerhold
2023-05-19 10:22 ` Bhupesh Sharma
2023-05-19 10:42 ` Konrad Dybcio
2023-05-19 10:49 ` Bhupesh Sharma
2023-05-19 10:51 ` Konrad Dybcio [this message]
2023-04-05 7:28 ` [PATCH v6 08/11] arm64: dts: qcom: sm8150: " Bhupesh Sharma
2023-04-06 13:58 ` Konrad Dybcio
2023-05-19 10:33 ` Bhupesh Sharma
2023-04-05 7:28 ` [PATCH v6 09/11] arm64: dts: qcom: sm8250: " Bhupesh Sharma
2023-04-06 13:59 ` Konrad Dybcio
2023-05-19 10:34 ` Bhupesh Sharma
2023-04-05 7:28 ` [PATCH v6 10/11] arm64: dts: qcom: sm8350: " Bhupesh Sharma
2023-04-05 7:28 ` [PATCH v6 11/11] arm64: dts: qcom: sm8450: add crypto nodes Bhupesh Sharma
2023-04-12 11:55 ` [PATCH v6 00/11] arm64: qcom: Enable Crypto Engine for a few Qualcomm SoCs Naresh Kamboju
2023-06-16 17:42 ` Krzysztof Kozlowski
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=875dec34-35da-e427-ae32-598958762dd2@linaro.org \
--to=konrad.dybcio@linaro.org \
--cc=agross@kernel.org \
--cc=andersson@kernel.org \
--cc=bhupesh.linux@gmail.com \
--cc=bhupesh.sharma@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=djakov@kernel.org \
--cc=krzysztof.kozlowski@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-crypto@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=neil.armstrong@linaro.org \
--cc=rfoss@kernel.org \
--cc=robh+dt@kernel.org \
--cc=stephan@gerhold.net \
--cc=vladimir.zapolskiy@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).