* [PATCH] arm64: dts: qcom: sm8350: fix the node unit addresses
@ 2021-05-10 7:05 Vinod Koul
2021-05-10 8:31 ` Robert Foss
0 siblings, 1 reply; 2+ messages in thread
From: Vinod Koul @ 2021-05-10 7:05 UTC (permalink / raw)
To: Bjorn Andersson
Cc: linux-arm-msm, Vinod Koul, Andy Gross, Rob Herring, Robert Foss,
devicetree, linux-kernel
Some node unit addresses were put wrongly in the dts, resulting in
below warning when run with W=1
arch/arm64/boot/dts/qcom/sm8350.dtsi:693.34-702.5: Warning (simple_bus_reg): /soc@0/thermal-sensor@c222000: simple-bus unit address format error, expected "c263000"
arch/arm64/boot/dts/qcom/sm8350.dtsi:704.34-713.5: Warning (simple_bus_reg): /soc@0/thermal-sensor@c223000: simple-bus unit address format error, expected "c265000"
arch/arm64/boot/dts/qcom/sm8350.dtsi:1180.32-1185.5: Warning (simple_bus_reg): /soc@0/interconnect@90e0000: simple-bus unit address format error, expected "90c0000"
Fix by correcting to the correct address as given in reg node
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
arch/arm64/boot/dts/qcom/sm8350.dtsi | 7 ++++---
1 file changed, 4 insertions(+), 3 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi
index a8cd224a2f31..d015a9ca95a5 100644
--- a/arch/arm64/boot/dts/qcom/sm8350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi
@@ -6,6 +6,7 @@
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/qcom,gcc-sm8350.h>
#include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/interconnect/qcom,sm8350.h>
#include <dt-bindings/mailbox/qcom-ipcc.h>
#include <dt-bindings/power/qcom-aoss-qmp.h>
#include <dt-bindings/power/qcom-rpmpd.h>
@@ -689,7 +690,7 @@ pdc: interrupt-controller@b220000 {
interrupt-controller;
};
- tsens0: thermal-sensor@c222000 {
+ tsens0: thermal-sensor@c263000 {
compatible = "qcom,sm8350-tsens", "qcom,tsens-v2";
reg = <0 0x0c263000 0 0x1ff>, /* TM */
<0 0x0c222000 0 0x8>; /* SROT */
@@ -700,7 +701,7 @@ tsens0: thermal-sensor@c222000 {
#thermal-sensor-cells = <1>;
};
- tsens1: thermal-sensor@c223000 {
+ tsens1: thermal-sensor@c265000 {
compatible = "qcom,sm8350-tsens", "qcom,tsens-v2";
reg = <0 0x0c265000 0 0x1ff>, /* TM */
<0 0x0c223000 0 0x8>; /* SROT */
@@ -1176,7 +1177,7 @@ usb_2_ssphy: phy@88ebe00 {
};
};
- dc_noc: interconnect@90e0000 {
+ dc_noc: interconnect@90c0000 {
compatible = "qcom,sm8350-dc-noc";
reg = <0 0x090c0000 0 0x4200>;
#interconnect-cells = <1>;
--
2.26.3
^ permalink raw reply related [flat|nested] 2+ messages in thread
* Re: [PATCH] arm64: dts: qcom: sm8350: fix the node unit addresses
2021-05-10 7:05 [PATCH] arm64: dts: qcom: sm8350: fix the node unit addresses Vinod Koul
@ 2021-05-10 8:31 ` Robert Foss
0 siblings, 0 replies; 2+ messages in thread
From: Robert Foss @ 2021-05-10 8:31 UTC (permalink / raw)
To: Vinod Koul
Cc: Bjorn Andersson, MSM, Andy Gross, Rob Herring,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
linux-kernel
Hey Vinod,
Thanks for catching this.
On Mon, 10 May 2021 at 09:05, Vinod Koul <vkoul@kernel.org> wrote:
>
> Some node unit addresses were put wrongly in the dts, resulting in
> below warning when run with W=1
>
> arch/arm64/boot/dts/qcom/sm8350.dtsi:693.34-702.5: Warning (simple_bus_reg): /soc@0/thermal-sensor@c222000: simple-bus unit address format error, expected "c263000"
> arch/arm64/boot/dts/qcom/sm8350.dtsi:704.34-713.5: Warning (simple_bus_reg): /soc@0/thermal-sensor@c223000: simple-bus unit address format error, expected "c265000"
> arch/arm64/boot/dts/qcom/sm8350.dtsi:1180.32-1185.5: Warning (simple_bus_reg): /soc@0/interconnect@90e0000: simple-bus unit address format error, expected "90c0000"
>
> Fix by correcting to the correct address as given in reg node
>
> Signed-off-by: Vinod Koul <vkoul@kernel.org>
> ---
> arch/arm64/boot/dts/qcom/sm8350.dtsi | 7 ++++---
> 1 file changed, 4 insertions(+), 3 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi
> index a8cd224a2f31..d015a9ca95a5 100644
> --- a/arch/arm64/boot/dts/qcom/sm8350.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi
> @@ -6,6 +6,7 @@
> #include <dt-bindings/interrupt-controller/arm-gic.h>
> #include <dt-bindings/clock/qcom,gcc-sm8350.h>
> #include <dt-bindings/clock/qcom,rpmh.h>
> +#include <dt-bindings/interconnect/qcom,sm8350.h>
> #include <dt-bindings/mailbox/qcom-ipcc.h>
> #include <dt-bindings/power/qcom-aoss-qmp.h>
> #include <dt-bindings/power/qcom-rpmpd.h>
> @@ -689,7 +690,7 @@ pdc: interrupt-controller@b220000 {
> interrupt-controller;
> };
>
> - tsens0: thermal-sensor@c222000 {
> + tsens0: thermal-sensor@c263000 {
> compatible = "qcom,sm8350-tsens", "qcom,tsens-v2";
> reg = <0 0x0c263000 0 0x1ff>, /* TM */
> <0 0x0c222000 0 0x8>; /* SROT */
> @@ -700,7 +701,7 @@ tsens0: thermal-sensor@c222000 {
> #thermal-sensor-cells = <1>;
> };
>
> - tsens1: thermal-sensor@c223000 {
> + tsens1: thermal-sensor@c265000 {
> compatible = "qcom,sm8350-tsens", "qcom,tsens-v2";
> reg = <0 0x0c265000 0 0x1ff>, /* TM */
> <0 0x0c223000 0 0x8>; /* SROT */
> @@ -1176,7 +1177,7 @@ usb_2_ssphy: phy@88ebe00 {
> };
> };
>
> - dc_noc: interconnect@90e0000 {
> + dc_noc: interconnect@90c0000 {
> compatible = "qcom,sm8350-dc-noc";
> reg = <0 0x090c0000 0 0x4200>;
> #interconnect-cells = <1>;
Reviewed-by: Robert Foss <robert.foss@linaro.org>
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2021-05-10 8:31 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-05-10 7:05 [PATCH] arm64: dts: qcom: sm8350: fix the node unit addresses Vinod Koul
2021-05-10 8:31 ` Robert Foss
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).