* [PATCH V2 2/2] cpufreq: imx6q: add 696MHz operating point for i.mx6ul
2018-01-06 10:42 [PATCH V2 1/2] ARM: dts: imx6ul: add 696MHz operating point Anson Huang
@ 2018-01-06 10:42 ` Anson Huang
2018-02-02 0:47 ` Shawn Guo
0 siblings, 1 reply; 3+ messages in thread
From: Anson Huang @ 2018-01-06 10:42 UTC (permalink / raw)
To: shawnguo, kernel, fabio.estevam, robh+dt, mark.rutland, rjw,
linux, viresh.kumar, rafael
Cc: linux-arm-kernel, devicetree, linux-kernel, linux-pm
Add 696MHz operating point for i.MX6UL, only for those
parts with speed grading fuse set to 2b'10 supports
696MHz operating point, so, speed grading check is also
added for i.MX6UL in this patch, the clock tree for each
operating point are as below:
696MHz:
pll1 696000000
pll1_bypass 696000000
pll1_sys 696000000
pll1_sw 696000000
arm 696000000
528MHz:
pll2 528000000
pll2_bypass 528000000
pll2_bus 528000000
ca7_secondary_sel 528000000
step 528000000
pll1_sw 528000000
arm 528000000
396MHz:
pll2_pfd2_396m 396000000
ca7_secondary_sel 396000000
step 396000000
pll1_sw 396000000
arm 396000000
198MHz:
pll2_pfd2_396m 396000000
ca7_secondary_sel 396000000
step 396000000
pll1_sw 396000000
arm 198000000
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
---
changes since v1:
redo the patch based on linux-next-pm.
drivers/cpufreq/imx6q-cpufreq.c | 46 ++++++++++++++++++++++++++++++++++++++++-
1 file changed, 45 insertions(+), 1 deletion(-)
diff --git a/drivers/cpufreq/imx6q-cpufreq.c b/drivers/cpufreq/imx6q-cpufreq.c
index 8bfb077..741f22e 100644
--- a/drivers/cpufreq/imx6q-cpufreq.c
+++ b/drivers/cpufreq/imx6q-cpufreq.c
@@ -136,6 +136,10 @@ static int imx6q_set_target(struct cpufreq_policy *policy, unsigned int index)
clks[PLL2_PFD2_396M].clk);
clk_set_parent(clks[STEP].clk, clks[SECONDARY_SEL].clk);
clk_set_parent(clks[PLL1_SW].clk, clks[STEP].clk);
+ if (freq_hz > clk_get_rate(clks[PLL2_BUS].clk)) {
+ clk_set_rate(clks[PLL1_SYS].clk, new_freq * 1000);
+ clk_set_parent(clks[PLL1_SW].clk, clks[PLL1_SYS].clk);
+ }
} else {
clk_set_parent(clks[STEP].clk, clks[PLL2_PFD2_396M].clk);
clk_set_parent(clks[PLL1_SW].clk, clks[STEP].clk);
@@ -260,6 +264,43 @@ static void imx6q_opp_check_speed_grading(struct device *dev)
of_node_put(np);
}
+#define OCOTP_CFG3_6UL_SPEED_696MHZ 0x2
+
+static void imx6ul_opp_check_speed_grading(struct device *dev)
+{
+ struct device_node *np;
+ void __iomem *base;
+ u32 val;
+
+ np = of_find_compatible_node(NULL, NULL, "fsl,imx6ul-ocotp");
+ if (!np)
+ return;
+
+ base = of_iomap(np, 0);
+ if (!base) {
+ dev_err(dev, "failed to map ocotp\n");
+ goto put_node;
+ }
+
+ /*
+ * Speed GRADING[1:0] defines the max speed of ARM:
+ * 2b'00: Reserved;
+ * 2b'01: 528000000Hz;
+ * 2b'10: 696000000Hz;
+ * 2b'11: Reserved;
+ * We need to set the max speed of ARM according to fuse map.
+ */
+ val = readl_relaxed(base + OCOTP_CFG3);
+ val >>= OCOTP_CFG3_SPEED_SHIFT;
+ val &= 0x3;
+ if (val != OCOTP_CFG3_6UL_SPEED_696MHZ)
+ if (dev_pm_opp_disable(dev, 696000000))
+ dev_warn(dev, "failed to disable 696MHz OPP\n");
+ iounmap(base);
+put_node:
+ of_node_put(np);
+}
+
static int imx6q_cpufreq_probe(struct platform_device *pdev)
{
struct device_node *np;
@@ -314,7 +355,10 @@ static int imx6q_cpufreq_probe(struct platform_device *pdev)
goto put_reg;
}
- imx6q_opp_check_speed_grading(cpu_dev);
+ if (of_machine_is_compatible("fsl,imx6ul"))
+ imx6ul_opp_check_speed_grading(cpu_dev);
+ else
+ imx6q_opp_check_speed_grading(cpu_dev);
/* Because we have added the OPPs here, we must free them */
free_opp = true;
--
1.9.1
^ permalink raw reply related [flat|nested] 3+ messages in thread