From: Ilia Lin <ilialin@codeaurora.org>
To: mturquette@baylibre.com, sboyd@kernel.org, robh@kernel.org,
mark.rutland@arm.com, viresh.kumar@linaro.org, nm@ti.com,
lgirdwood@gmail.com, broonie@kernel.org, andy.gross@linaro.org,
david.brown@linaro.org, catalin.marinas@arm.com,
will.deacon@arm.com, rjw@rjwysocki.net,
linux-clk@vger.kernel.org
Cc: devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-pm@vger.kernel.org, linux-arm-msm@vger.kernel.org,
linux-soc@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
rnayak@codeaurora.org, ilialin@codeaurora.org,
amit.kucheria@linaro.org, nicolas.dechesne@linaro.org,
celster@codeaurora.org, tfinkel@codeaurora.org
Subject: [PATCH v8 11/15] dt-bindings: cpufreq: Document operating-points-v2-kryo-cpu
Date: Thu, 17 May 2018 14:19:11 +0300 [thread overview]
Message-ID: <1526555955-29960-12-git-send-email-ilialin@codeaurora.org> (raw)
In-Reply-To: <1526555955-29960-1-git-send-email-ilialin@codeaurora.org>
The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC
to provide the OPP framework with required information.
This is used to determine the voltage and frequency value for each OPP of
operating-points-v2 table when it is parsed by the OPP framework.
This change adds documentation for the DT bindings.
The "operating-points-v2-kryo-cpu" DT extends the "operating-points-v2"
with following parameters:
- nvmem-cells (NVMEM area containig the speedbin information)
- opp-supported-hw: A single 32 bit bitmap value,
representing compatible HW:
0: MSM8996 V3, speedbin 0
1: MSM8996 V3, speedbin 1
2: MSM8996 V3, speedbin 2
3: unused
4: MSM8996 SG, speedbin 0
5: MSM8996 SG, speedbin 1
6: MSM8996 SG, speedbin 2
7-31: unused
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
---
.../devicetree/bindings/opp/kryo-cpufreq.txt | 680 +++++++++++++++++++++
1 file changed, 680 insertions(+)
create mode 100644 Documentation/devicetree/bindings/opp/kryo-cpufreq.txt
diff --git a/Documentation/devicetree/bindings/opp/kryo-cpufreq.txt b/Documentation/devicetree/bindings/opp/kryo-cpufreq.txt
new file mode 100644
index 0000000..c2127b9
--- /dev/null
+++ b/Documentation/devicetree/bindings/opp/kryo-cpufreq.txt
@@ -0,0 +1,680 @@
+Qualcomm Technologies, Inc. KRYO CPUFreq and OPP bindings
+===================================
+
+In Certain Qualcomm Technologies, Inc. SoCs like apq8096 and msm8996
+that have KRYO processors, the CPU ferequencies subset and voltage value
+of each OPP varies based on the silicon variant in use.
+Qualcomm Technologies, Inc. Process Voltage Scaling Tables
+defines the voltage and frequency value based on the msm-id in SMEM
+and speedbin blown in the efuse combination.
+The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC
+to provide the OPP framework with required information (existing HW bitmap).
+This is used to determine the voltage and frequency value for each OPP of
+operating-points-v2 table when it is parsed by the OPP framework.
+
+Required properties:
+--------------------
+In 'cpus' nodes:
+- operating-points-v2: Phandle to the operating-points-v2 table to use.
+
+In 'operating-points-v2' table:
+- compatible: Should be
+ - 'operating-points-v2-kryo-cpu' for apq8096 and msm8996.
+- nvmem-cells: A phandle pointing to a nvmem-cells node representing the
+ efuse registers that has information about the
+ speedbin that is used to select the right frequency/voltage
+ value pair.
+ Please refer the for nvmem-cells
+ bindings Documentation/devicetree/bindings/nvmem/nvmem.txt
+ and also examples below.
+
+In every OPP node:
+- opp-supported-hw: A single 32 bit bitmap value, representing compatible HW.
+ Bitmap:
+ 0: MSM8996 V3, speedbin 0
+ 1: MSM8996 V3, speedbin 1
+ 2: MSM8996 V3, speedbin 2
+ 3: unused
+ 4: MSM8996 SG, speedbin 0
+ 5: MSM8996 SG, speedbin 1
+ 6: MSM8996 SG, speedbin 2
+ 7-31: unused
+
+Example 1:
+---------
+
+ cpus {
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ CPU0: cpu@0 {
+ device_type = "cpu";
+ compatible = "qcom,kryo";
+ reg = <0x0 0x0>;
+ enable-method = "psci";
+ clocks = <&kryocc 0>;
+ cpu-supply = <&pm8994_s11_saw>;
+ operating-points-v2 = <&cluster0_opp>;
+ #cooling-cells = <2>;
+ next-level-cache = <&L2_0>;
+ L2_0: l2-cache {
+ compatible = "cache";
+ cache-level = <2>;
+ };
+ };
+
+ CPU1: cpu@1 {
+ device_type = "cpu";
+ compatible = "qcom,kryo";
+ reg = <0x0 0x1>;
+ enable-method = "psci";
+ clocks = <&kryocc 0>;
+ cpu-supply = <&pm8994_s11_saw>;
+ operating-points-v2 = <&cluster0_opp>;
+ #cooling-cells = <2>;
+ next-level-cache = <&L2_0>;
+ };
+
+ CPU2: cpu@100 {
+ device_type = "cpu";
+ compatible = "qcom,kryo";
+ reg = <0x0 0x100>;
+ enable-method = "psci";
+ clocks = <&kryocc 1>;
+ cpu-supply = <&pm8994_s11_saw>;
+ operating-points-v2 = <&cluster1_opp>;
+ #cooling-cells = <2>;
+ next-level-cache = <&L2_1>;
+ L2_1: l2-cache {
+ compatible = "cache";
+ cache-level = <2>;
+ };
+ };
+
+ CPU3: cpu@101 {
+ device_type = "cpu";
+ compatible = "qcom,kryo";
+ reg = <0x0 0x101>;
+ enable-method = "psci";
+ clocks = <&kryocc 1>;
+ cpu-supply = <&pm8994_s11_saw>;
+ operating-points-v2 = <&cluster1_opp>;
+ #cooling-cells = <2>;
+ next-level-cache = <&L2_1>;
+ };
+
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&CPU0>;
+ };
+
+ core1 {
+ cpu = <&CPU1>;
+ };
+ };
+
+ cluster1 {
+ core0 {
+ cpu = <&CPU2>;
+ };
+
+ core1 {
+ cpu = <&CPU3>;
+ };
+ };
+ };
+ };
+
+ cluster0_opp: opp_table0 {
+ compatible = "operating-points-v2-kryo-cpu";
+ nvmem-cells = <&speedbin_efuse>;
+ opp-shared;
+
+ opp-307200000 {
+ opp-hz = /bits/ 64 <307200000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x77>;
+ clock-latency-ns = <200000>;
+ };
+ opp-384000000 {
+ opp-hz = /bits/ 64 <384000000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-422400000 {
+ opp-hz = /bits/ 64 <422400000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-460800000 {
+ opp-hz = /bits/ 64 <460800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-480000000 {
+ opp-hz = /bits/ 64 <480000000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-537600000 {
+ opp-hz = /bits/ 64 <537600000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-556800000 {
+ opp-hz = /bits/ 64 <556800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-614400000 {
+ opp-hz = /bits/ 64 <614400000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-652800000 {
+ opp-hz = /bits/ 64 <652800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-691200000 {
+ opp-hz = /bits/ 64 <691200000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-729600000 {
+ opp-hz = /bits/ 64 <729600000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-768000000 {
+ opp-hz = /bits/ 64 <768000000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-844800000 {
+ opp-hz = /bits/ 64 <844800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x77>;
+ clock-latency-ns = <200000>;
+ };
+ opp-902400000 {
+ opp-hz = /bits/ 64 <902400000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-960000000 {
+ opp-hz = /bits/ 64 <960000000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-979200000 {
+ opp-hz = /bits/ 64 <979200000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1036800000 {
+ opp-hz = /bits/ 64 <1036800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1056000000 {
+ opp-hz = /bits/ 64 <1056000000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1113600000 {
+ opp-hz = /bits/ 64 <1113600000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1132800000 {
+ opp-hz = /bits/ 64 <1132800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1190400000 {
+ opp-hz = /bits/ 64 <1190400000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1209600000 {
+ opp-hz = /bits/ 64 <1209600000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1228800000 {
+ opp-hz = /bits/ 64 <1228800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1286400000 {
+ opp-hz = /bits/ 64 <1286400000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1324800000 {
+ opp-hz = /bits/ 64 <1324800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x5>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1363200000 {
+ opp-hz = /bits/ 64 <1363200000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x72>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1401600000 {
+ opp-hz = /bits/ 64 <1401600000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x5>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1440000000 {
+ opp-hz = /bits/ 64 <1440000000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1478400000 {
+ opp-hz = /bits/ 64 <1478400000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x1>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1497600000 {
+ opp-hz = /bits/ 64 <1497600000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x4>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1516800000 {
+ opp-hz = /bits/ 64 <1516800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1593600000 {
+ opp-hz = /bits/ 64 <1593600000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x71>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1996800000 {
+ opp-hz = /bits/ 64 <1996800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x20>;
+ clock-latency-ns = <200000>;
+ };
+ opp-2188800000 {
+ opp-hz = /bits/ 64 <2188800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x10>;
+ clock-latency-ns = <200000>;
+ };
+ };
+
+ cluster1_opp: opp_table1 {
+ compatible = "operating-points-v2-kryo-cpu";
+ nvmem-cells = <&speedbin_efuse>;
+ opp-shared;
+
+ opp-307200000 {
+ opp-hz = /bits/ 64 <307200000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x77>;
+ clock-latency-ns = <200000>;
+ };
+ opp-384000000 {
+ opp-hz = /bits/ 64 <384000000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-403200000 {
+ opp-hz = /bits/ 64 <403200000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-460800000 {
+ opp-hz = /bits/ 64 <460800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-480000000 {
+ opp-hz = /bits/ 64 <480000000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-537600000 {
+ opp-hz = /bits/ 64 <537600000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-556800000 {
+ opp-hz = /bits/ 64 <556800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-614400000 {
+ opp-hz = /bits/ 64 <614400000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-652800000 {
+ opp-hz = /bits/ 64 <652800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-691200000 {
+ opp-hz = /bits/ 64 <691200000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-729600000 {
+ opp-hz = /bits/ 64 <729600000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-748800000 {
+ opp-hz = /bits/ 64 <748800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-806400000 {
+ opp-hz = /bits/ 64 <806400000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-825600000 {
+ opp-hz = /bits/ 64 <825600000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-883200000 {
+ opp-hz = /bits/ 64 <883200000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-902400000 {
+ opp-hz = /bits/ 64 <902400000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-940800000 {
+ opp-hz = /bits/ 64 <940800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-979200000 {
+ opp-hz = /bits/ 64 <979200000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1036800000 {
+ opp-hz = /bits/ 64 <1036800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1056000000 {
+ opp-hz = /bits/ 64 <1056000000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1113600000 {
+ opp-hz = /bits/ 64 <1113600000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1132800000 {
+ opp-hz = /bits/ 64 <1132800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1190400000 {
+ opp-hz = /bits/ 64 <1190400000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1209600000 {
+ opp-hz = /bits/ 64 <1209600000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1248000000 {
+ opp-hz = /bits/ 64 <1248000000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1286400000 {
+ opp-hz = /bits/ 64 <1286400000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1324800000 {
+ opp-hz = /bits/ 64 <1324800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1363200000 {
+ opp-hz = /bits/ 64 <1363200000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1401600000 {
+ opp-hz = /bits/ 64 <1401600000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1440000000 {
+ opp-hz = /bits/ 64 <1440000000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1478400000 {
+ opp-hz = /bits/ 64 <1478400000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1516800000 {
+ opp-hz = /bits/ 64 <1516800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1555200000 {
+ opp-hz = /bits/ 64 <1555200000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1593600000 {
+ opp-hz = /bits/ 64 <1593600000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1632000000 {
+ opp-hz = /bits/ 64 <1632000000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1670400000 {
+ opp-hz = /bits/ 64 <1670400000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1708800000 {
+ opp-hz = /bits/ 64 <1708800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1747200000 {
+ opp-hz = /bits/ 64 <1747200000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1785600000 {
+ opp-hz = /bits/ 64 <1785600000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1804800000 {
+ opp-hz = /bits/ 64 <1804800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x6>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1824000000 {
+ opp-hz = /bits/ 64 <1824000000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x71>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1900800000 {
+ opp-hz = /bits/ 64 <1900800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x74>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1920000000 {
+ opp-hz = /bits/ 64 <1920000000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x1>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1977600000 {
+ opp-hz = /bits/ 64 <1977600000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x30>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1996800000 {
+ opp-hz = /bits/ 64 <1996800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x1>;
+ clock-latency-ns = <200000>;
+ };
+ opp-2054400000 {
+ opp-hz = /bits/ 64 <2054400000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x30>;
+ clock-latency-ns = <200000>;
+ };
+ opp-2073600000 {
+ opp-hz = /bits/ 64 <2073600000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x1>;
+ clock-latency-ns = <200000>;
+ };
+ opp-2150400000 {
+ opp-hz = /bits/ 64 <2150400000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x31>;
+ clock-latency-ns = <200000>;
+ };
+ opp-2246400000 {
+ opp-hz = /bits/ 64 <2246400000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x10>;
+ clock-latency-ns = <200000>;
+ };
+ opp-2342400000 {
+ opp-hz = /bits/ 64 <2342400000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x10>;
+ clock-latency-ns = <200000>;
+ };
+ };
+
+....
+
+reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+....
+ smem_mem: smem-mem@86000000 {
+ reg = <0x0 0x86000000 0x0 0x200000>;
+ no-map;
+ };
+....
+};
+
+smem {
+ compatible = "qcom,smem";
+ memory-region = <&smem_mem>;
+ hwlocks = <&tcsr_mutex 3>;
+};
+
+soc {
+....
+ qfprom: qfprom@74000 {
+ compatible = "qcom,qfprom";
+ reg = <0x00074000 0x8ff>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ....
+ speedbin_efuse: speedbin@133 {
+ reg = <0x133 0x1>;
+ bits = <5 3>;
+ };
+ };
+};
--
1.9.1
next prev parent reply other threads:[~2018-05-17 11:19 UTC|newest]
Thread overview: 50+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-05-17 11:19 [PATCH v8 00/15] CPU scaling support for msm8996 Ilia Lin
2018-05-17 11:19 ` [PATCH v8 01/15] soc: qcom: Separate kryo l2 accessors from PMU driver Ilia Lin
2018-05-17 11:19 ` [PATCH v8 02/15] clk: qcom: Make clk_alpha_pll_configure available to modules Ilia Lin
2018-05-17 11:19 ` [PATCH v8 03/15] clk: Use devm_ in the register fixed factor clock Ilia Lin
2018-05-17 11:19 ` [PATCH v8 04/15] clk: qcom: Add CPU clock driver for msm8996 Ilia Lin
2018-05-22 13:49 ` kbuild test robot
2018-05-17 11:19 ` [PATCH v8 05/15] dt-bindings: clk: qcom: Add bindings for CPU clock " Ilia Lin
2018-05-17 11:19 ` [PATCH v8 06/15] clk: qcom: cpu-8996: Add support to switch to alternate PLL Ilia Lin
2018-05-17 11:19 ` [PATCH v8 07/15] clk: qcom: cpu-8996: Add support to switch below 600Mhz Ilia Lin
2018-05-17 11:19 ` [PATCH v8 08/15] clk: qcom: Add ACD path to CPU clock driver for msm8996 Ilia Lin
2018-05-17 11:19 ` [PATCH v8 09/15] dt: qcom: Add opp and thermal to the msm8996 Ilia Lin
2018-05-17 11:19 ` [PATCH v8 10/15] cpufreq: Add Kryo CPU scaling driver Ilia Lin
2018-05-18 1:45 ` Viresh Kumar
2018-05-19 11:09 ` ilialin
2018-05-19 11:54 ` Russell King - ARM Linux
2018-05-19 11:41 ` ilialin
2018-05-19 11:45 ` ilialin
2018-05-21 4:49 ` Viresh Kumar
2018-05-21 9:00 ` ilialin
2018-05-21 9:05 ` Viresh Kumar
2018-05-19 11:35 ` [PATCH] " Ilia Lin
2018-05-21 5:04 ` Viresh Kumar
2018-05-21 12:50 ` Sudeep Holla
2018-05-21 12:57 ` ilialin
2018-05-21 13:04 ` Sudeep Holla
2018-05-22 6:56 ` ilialin
2018-05-22 9:12 ` Sudeep Holla
2018-05-22 7:59 ` ilialin
2018-05-22 9:18 ` Sudeep Holla
2018-05-22 9:38 ` Viresh Kumar
2018-05-22 11:29 ` Ilia Lin
2018-05-22 13:07 ` Sudeep Holla
2018-05-23 5:44 ` Viresh Kumar
2018-05-23 9:05 ` Ilia Lin
2018-05-23 9:32 ` Viresh Kumar
2018-05-23 9:40 ` Russell King - ARM Linux
2018-05-23 9:59 ` Viresh Kumar
2018-05-21 10:31 ` Ilia Lin
2018-05-21 10:37 ` Viresh Kumar
2018-05-21 10:54 ` Russell King - ARM Linux
2018-05-21 11:05 ` ilialin
2018-05-21 12:11 ` Russell King - ARM Linux
2018-05-21 12:35 ` ilialin
2018-05-21 12:41 ` Russell King - ARM Linux
2018-05-17 11:19 ` Ilia Lin [this message]
2018-05-18 14:26 ` [PATCH v8 11/15] dt-bindings: cpufreq: Document operating-points-v2-kryo-cpu Rob Herring
2018-05-17 11:19 ` [PATCH v8 12/15] dt: qcom: Add qcom-cpufreq-kryo driver configuration Ilia Lin
2018-05-17 11:19 ` [PATCH v8 13/15] regulator: qcom_spmi: Add support for SAW Ilia Lin
2018-05-17 11:19 ` [PATCH v8 14/15] dt-bindings: qcom_spmi: Document SAW support Ilia Lin
2018-05-17 11:19 ` [PATCH v8 15/15] dt: qcom: Add SAW regulator for 8x96 CPUs Ilia Lin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1526555955-29960-12-git-send-email-ilialin@codeaurora.org \
--to=ilialin@codeaurora.org \
--cc=amit.kucheria@linaro.org \
--cc=andy.gross@linaro.org \
--cc=broonie@kernel.org \
--cc=catalin.marinas@arm.com \
--cc=celster@codeaurora.org \
--cc=david.brown@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=lgirdwood@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=linux-soc@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=mturquette@baylibre.com \
--cc=nicolas.dechesne@linaro.org \
--cc=nm@ti.com \
--cc=rjw@rjwysocki.net \
--cc=rnayak@codeaurora.org \
--cc=robh@kernel.org \
--cc=sboyd@kernel.org \
--cc=tfinkel@codeaurora.org \
--cc=viresh.kumar@linaro.org \
--cc=will.deacon@arm.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).