From: "Ricardo Cañuelo" <ricardo.canuelo@collabora.com>
To: laurent.pinchart@ideasonboard.com
Cc: kernel@collabora.com, devicetree@vger.kernel.org,
linux-arm-kernel@lists.infradead.org, geert+renesas@glider.be,
robh+dt@kernel.org, xuwei5@hisilicon.com
Subject: [PATCH v2 0/6] Convert adi,adv7511.txt DT bindings to yaml
Date: Mon, 11 May 2020 13:06:05 +0200 [thread overview]
Message-ID: <20200511110611.3142-1-ricardo.canuelo@collabora.com> (raw)
Hi,
This series convert the adi,adv7511.txt DT bindings to json-schema. As a
result of the conversion some dts files needed to be updated.
The changes to the dts files are of three types:
- Reordering of the I2C slave addresses list of the ADV75xx node. The
addresses in the 'reg' property and the matching names in
'reg-names' for an I2C slave don't need to be in any particular
order, but the DT schema defines these properties as a cell array
and a string array respectively, which are ordered, so the
definitions in the dts files must match the order in the binding.
- Filling the minimum binding requirements. Most of the time this
means creating a 'ports' node in the boards that don't define
them. Note, however, that the purpose of this is simply to make the
definition compliant with the binding. I didn't define any endpoints
for the ports.
- Removing unneeded properties.
About the binding conversion:
- The original binding covered five different devices: ADV7511,
ADV7511W, ADV7513, ADV7533 and ADV7535. They all share a common set
of properties but ADV7533 and ADV7535 have enough differences from
the rest to warrant their own binding file. In v1 I modelled all the
properties constraints for all five devices in a single file but it
turned out a bit too complex. Splitting the binding into one for
ADV7511/11W/13 and another for ADV7533/35 makes them much easier to
read and maintain.
Patches 1/6 to 5/6 contain the dts changes. Patch 6/6 contains the
binding conversion.
NOTE: the bindings have been tested with:
make dt_binding_check ARCH=<arch> DT_SCHEMA_FILES=<...adi,adv7511.yaml>
make dtbs_check ARCH=<arch> DT_SCHEMA_FILES=<...adi,adv7511.yaml>
for <arch> = arm and arm64. dts changes haven't been tested in hardware.
Changes in v2:
- [Rob] adi,adv7511.yaml split into two files: adi,adv7511.yaml and
adi,adv7533.yaml.
- [Rob] Remove maxItems from supplies.
- Additional DTs fixes:
- iwg20d-q7-dbcm-ca.dtsi
- r8a7745-iwg22d-sodimm-dbhd-ca.dts
- r8a7790-lager.dts
- r8a7790-stout.dts
- r8a7791-koelsch.dts
- r8a7791-porter.dts
- r8a7792-blanche.dts
- r8a7793-gose.dts
- r8a7794-silk.dts
- hi6220-hikey.dts
- r8a77970-eagle.dts
- r8a77970-v3msk.dts
- r8a77980-condor.dts
- r8a77980-v3hsk.dts
- r8a77990-ebisu.dts
Kind regards,
Ricardo
Ricardo Cañuelo (6):
arm64: dts: renesas: make hdmi encoder nodes compliant with DT
bindings
ARM: dts: renesas: make hdmi encoder nodes compliant with DT bindings
ARM: dts: zynq: add port definitions to hdmi-tx@39
arm64: dts: hisilicon: hikey: fixes to comply with adi,adv7533 DT
binding
ARM: dts: iwg20d-q7-dbcm-ca: remove unneeded properties in hdmi@39
dt-bindings: drm: bridge: adi,adv7511.txt: convert to yaml
.../bindings/display/bridge/adi,adv7511.txt | 143 -----------
.../bindings/display/bridge/adi,adv7511.yaml | 230 ++++++++++++++++++
.../bindings/display/bridge/adi,adv7533.yaml | 166 +++++++++++++
arch/arm/boot/dts/iwg20d-q7-dbcm-ca.dtsi | 2 -
.../dts/r8a7745-iwg22d-sodimm-dbhd-ca.dts | 2 -
arch/arm/boot/dts/r8a7790-lager.dts | 2 -
arch/arm/boot/dts/r8a7790-stout.dts | 2 -
arch/arm/boot/dts/r8a7791-koelsch.dts | 2 -
arch/arm/boot/dts/r8a7791-porter.dts | 2 -
arch/arm/boot/dts/r8a7792-blanche.dts | 2 -
arch/arm/boot/dts/r8a7792-wheat.dts | 12 +-
arch/arm/boot/dts/r8a7793-gose.dts | 2 -
arch/arm/boot/dts/r8a7794-silk.dts | 2 -
arch/arm/boot/dts/zynq-zc702.dts | 10 +
arch/arm/boot/dts/zynq-zc706.dts | 10 +
.../boot/dts/hisilicon/hi3660-hikey960.dts | 11 +
.../arm64/boot/dts/hisilicon/hi6220-hikey.dts | 2 +-
.../arm64/boot/dts/renesas/r8a77970-eagle.dts | 2 -
.../arm64/boot/dts/renesas/r8a77970-v3msk.dts | 2 -
.../boot/dts/renesas/r8a77980-condor.dts | 2 -
.../arm64/boot/dts/renesas/r8a77980-v3hsk.dts | 2 -
.../arm64/boot/dts/renesas/r8a77990-ebisu.dts | 2 -
.../arm64/boot/dts/renesas/r8a77995-draak.dts | 6 +-
23 files changed, 434 insertions(+), 184 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt
create mode 100644 Documentation/devicetree/bindings/display/bridge/adi,adv7511.yaml
create mode 100644 Documentation/devicetree/bindings/display/bridge/adi,adv7533.yaml
--
2.18.0
next reply other threads:[~2020-05-11 11:06 UTC|newest]
Thread overview: 33+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-05-11 11:06 Ricardo Cañuelo [this message]
2020-05-11 11:06 ` [PATCH v2 1/6] arm64: dts: renesas: make hdmi encoder nodes compliant with DT bindings Ricardo Cañuelo
2020-05-11 11:51 ` Geert Uytterhoeven
2020-05-14 1:33 ` Laurent Pinchart
2020-05-11 11:06 ` [PATCH v2 2/6] ARM: " Ricardo Cañuelo
2020-05-11 11:51 ` Geert Uytterhoeven
2020-05-14 1:34 ` Laurent Pinchart
2020-05-11 11:06 ` [PATCH v2 3/6] ARM: dts: zynq: add port definitions to hdmi-tx@39 Ricardo Cañuelo
2020-05-11 12:24 ` Ezequiel Garcia
2020-05-11 12:52 ` Michal Simek
2020-05-14 1:36 ` Laurent Pinchart
2020-05-11 11:06 ` [PATCH v2 4/6] arm64: dts: hisilicon: hikey: fixes to comply with adi,adv7533 DT binding Ricardo Cañuelo
2020-05-14 1:37 ` Laurent Pinchart
2020-08-04 20:57 ` [PATCH v2 4/6] arm64: dts: hisilicon: hikey: fixes to comply with adi, adv7533 " John Stultz
2020-08-04 21:24 ` John Stultz
2020-05-11 11:06 ` [PATCH v2 5/6] ARM: dts: iwg20d-q7-dbcm-ca: remove unneeded properties in hdmi@39 Ricardo Cañuelo
2020-05-11 11:52 ` Geert Uytterhoeven
2020-05-14 1:37 ` Laurent Pinchart
2020-05-11 11:06 ` [PATCH v2 6/6] dt-bindings: drm: bridge: adi,adv7511.txt: convert to yaml Ricardo Cañuelo
2020-05-14 1:54 ` Laurent Pinchart
2020-05-14 9:36 ` Ricardo Cañuelo
2020-05-14 15:22 ` Laurent Pinchart
2020-05-18 21:27 ` Rob Herring
2020-05-25 7:43 ` Ricardo Cañuelo
2020-05-26 1:44 ` Laurent Pinchart
2020-05-26 7:03 ` Geert Uytterhoeven
2020-05-26 10:11 ` Laurent Pinchart
2020-05-26 10:39 ` Geert Uytterhoeven
2020-05-26 19:45 ` Ezequiel Garcia
2020-05-27 17:29 ` Rob Herring
2020-05-27 18:18 ` Geert Uytterhoeven
2020-05-28 6:36 ` Ricardo Cañuelo
2020-05-11 11:55 ` [PATCH v2 0/6] Convert adi,adv7511.txt DT bindings " Geert Uytterhoeven
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200511110611.3142-1-ricardo.canuelo@collabora.com \
--to=ricardo.canuelo@collabora.com \
--cc=devicetree@vger.kernel.org \
--cc=geert+renesas@glider.be \
--cc=kernel@collabora.com \
--cc=laurent.pinchart@ideasonboard.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=robh+dt@kernel.org \
--cc=xuwei5@hisilicon.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).