* [PATCH 0/7] Pine64 PineCube support @ 2020-09-23 0:57 Icenowy Zheng 2020-09-23 0:57 ` [PATCH 1/7] ARM: dts: sun8i: V3/V3s/S3/S3L: add Ethernet support Icenowy Zheng ` (5 more replies) 0 siblings, 6 replies; 14+ messages in thread From: Icenowy Zheng @ 2020-09-23 0:57 UTC (permalink / raw) To: Rob Herring, Maxime Ripard, Chen-Yu Tsai Cc: devicetree, linux-arm-kernel, linux-kernel, linux-sunxi, Icenowy Zheng Pine64 PineCube is an IP camera based on Allwinner S3 chip. This patchset tries to add support for it. In order to make sure the system do not hang when camera is brought up, a fix to AXP209 driver is needed (sent individually), otherwise the system will hang because it changes the voltage of LDO2 when LDO4 tweaking. Icenowy Zheng (7): ARM: dts: sun8i: V3/V3s/S3/S3L: add Ethernet support ARM: dts: sun8i: V3/V3s/S3/S3L: add pinctrl for UART2 RX/TX ARM: dts: sun8i: V3/V3s/S3/S3L: add CSI1 device node ARM: dts: sun8i: V3/V3s/S3/S3L: add pinctrl for 8-bit parallel CSI ARM: dts: sun8i: V3/V3s/S3/S3L: add pinctrl for I2C1 at PE bank dt-bindings: arm: sunxi: add Pine64 PineCube binding ARM: dts: sun8i: s3l: add support for Pine64 PineCube IP camera .../devicetree/bindings/arm/sunxi.yaml | 5 + arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/sun8i-s3-pinecube.dts | 235 ++++++++++++++++++ arch/arm/boot/dts/sun8i-v3.dtsi | 13 + arch/arm/boot/dts/sun8i-v3s.dtsi | 91 +++++++ 5 files changed, 345 insertions(+) create mode 100644 arch/arm/boot/dts/sun8i-s3-pinecube.dts -- 2.27.0 ^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH 1/7] ARM: dts: sun8i: V3/V3s/S3/S3L: add Ethernet support 2020-09-23 0:57 [PATCH 0/7] Pine64 PineCube support Icenowy Zheng @ 2020-09-23 0:57 ` Icenowy Zheng 2020-09-23 0:58 ` [PATCH 2/7] ARM: dts: sun8i: V3/V3s/S3/S3L: add pinctrl for UART2 RX/TX Icenowy Zheng ` (4 subsequent siblings) 5 siblings, 0 replies; 14+ messages in thread From: Icenowy Zheng @ 2020-09-23 0:57 UTC (permalink / raw) To: Rob Herring, Maxime Ripard, Chen-Yu Tsai Cc: devicetree, linux-arm-kernel, linux-kernel, linux-sunxi, Icenowy Zheng The Allwinner V3/V3s/S3L/SoChip S3 Ethernet MAC and internal PHY is quite similar to the ones on Allwinner H3, except for V3s the external MII is not wired out. Add ethernet support to V3/V3s/S3/S3L. Signed-off-by: Icenowy Zheng <icenowy@aosc.io> --- arch/arm/boot/dts/sun8i-v3.dtsi | 13 ++++++++ arch/arm/boot/dts/sun8i-v3s.dtsi | 52 ++++++++++++++++++++++++++++++++ 2 files changed, 65 insertions(+) diff --git a/arch/arm/boot/dts/sun8i-v3.dtsi b/arch/arm/boot/dts/sun8i-v3.dtsi index 6ae8645ade50..ca4672ed2e02 100644 --- a/arch/arm/boot/dts/sun8i-v3.dtsi +++ b/arch/arm/boot/dts/sun8i-v3.dtsi @@ -9,6 +9,19 @@ &ccu { compatible = "allwinner,sun8i-v3-ccu"; }; +&emac { + /delete-property/ phy-handle; + /delete-property/ phy-mode; +}; + +&mdio_mux { + external_mdio: mdio@2 { + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + }; +}; + &pio { compatible = "allwinner,sun8i-v3-pinctrl"; }; diff --git a/arch/arm/boot/dts/sun8i-v3s.dtsi b/arch/arm/boot/dts/sun8i-v3s.dtsi index 6eb9c39aa93f..7d40897dab09 100644 --- a/arch/arm/boot/dts/sun8i-v3s.dtsi +++ b/arch/arm/boot/dts/sun8i-v3s.dtsi @@ -138,6 +138,15 @@ mixer0_out_tcon0: endpoint { }; }; + syscon: system-control@1c00000 { + compatible = "allwinner,sun8i-v3s-system-control", + "allwinner,sun8i-h3-system-control"; + reg = <0x01c00000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + }; + tcon0: lcd-controller@1c0c000 { compatible = "allwinner,sun8i-v3s-tcon"; reg = <0x01c0c000 0x1000>; @@ -415,6 +424,49 @@ i2c1: i2c@1c2b000 { #size-cells = <0>; }; + emac: ethernet@1c30000 { + compatible = "allwinner,sun8i-v3s-emac"; + syscon = <&syscon>; + reg = <0x01c30000 0x10000>; + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq"; + resets = <&ccu RST_BUS_EMAC>; + reset-names = "stmmaceth"; + clocks = <&ccu CLK_BUS_EMAC>; + clock-names = "stmmaceth"; + phy-handle = <&int_mii_phy>; + phy-mode = "mii"; + status = "disabled"; + + mdio: mdio { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + }; + + mdio_mux: mdio-mux { + compatible = "allwinner,sun8i-h3-mdio-mux"; + #address-cells = <1>; + #size-cells = <0>; + + mdio-parent-bus = <&mdio>; + /* Only one MDIO is usable at the time */ + internal_mdio: mdio@1 { + compatible = "allwinner,sun8i-h3-mdio-internal"; + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + int_mii_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + clocks = <&ccu CLK_BUS_EPHY>; + resets = <&ccu RST_BUS_EPHY>; + }; + }; + }; + }; + spi0: spi@1c68000 { compatible = "allwinner,sun8i-h3-spi"; reg = <0x01c68000 0x1000>; -- 2.27.0 ^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 2/7] ARM: dts: sun8i: V3/V3s/S3/S3L: add pinctrl for UART2 RX/TX 2020-09-23 0:57 [PATCH 0/7] Pine64 PineCube support Icenowy Zheng 2020-09-23 0:57 ` [PATCH 1/7] ARM: dts: sun8i: V3/V3s/S3/S3L: add Ethernet support Icenowy Zheng @ 2020-09-23 0:58 ` Icenowy Zheng 2020-09-23 0:58 ` [PATCH 3/7] ARM: dts: sun8i: V3/V3s/S3/S3L: add CSI1 device node Icenowy Zheng 2020-09-23 1:00 ` [PATCH 4/7] ARM: dts: sun8i: V3/V3s/S3/S3L: add pinctrl for 8-bit parallel CSI Icenowy Zheng ` (3 subsequent siblings) 5 siblings, 1 reply; 14+ messages in thread From: Icenowy Zheng @ 2020-09-23 0:58 UTC (permalink / raw) To: Rob Herring, Maxime Ripard, Chen-Yu Tsai Cc: devicetree, linux-arm-kernel, linux-kernel, linux-sunxi, Icenowy Zheng The UART2 RX/TX pins on Allwinner V3 series is at PB0/1, which is used as debugging UART on some boards. Add pinctrl node for them. Signed-off-by: Icenowy Zheng <icenowy@aosc.io> --- arch/arm/boot/dts/sun8i-v3s.dtsi | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/arch/arm/boot/dts/sun8i-v3s.dtsi b/arch/arm/boot/dts/sun8i-v3s.dtsi index 7d40897dab09..4cfdf193cf88 100644 --- a/arch/arm/boot/dts/sun8i-v3s.dtsi +++ b/arch/arm/boot/dts/sun8i-v3s.dtsi @@ -322,6 +322,11 @@ uart0_pb_pins: uart0-pb-pins { function = "uart0"; }; + uart2_pins: uart2-pins { + pins = "PB0", "PB1"; + function = "uart2"; + }; + mmc0_pins: mmc0-pins { pins = "PF0", "PF1", "PF2", "PF3", "PF4", "PF5"; @@ -397,6 +402,8 @@ uart2: serial@1c28800 { reg-io-width = <4>; clocks = <&ccu CLK_BUS_UART2>; resets = <&ccu RST_BUS_UART2>; + pinctrl-0 = <&uart2_pins>; + pinctrl-names = "default"; status = "disabled"; }; -- 2.27.0 ^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 3/7] ARM: dts: sun8i: V3/V3s/S3/S3L: add CSI1 device node 2020-09-23 0:58 ` [PATCH 2/7] ARM: dts: sun8i: V3/V3s/S3/S3L: add pinctrl for UART2 RX/TX Icenowy Zheng @ 2020-09-23 0:58 ` Icenowy Zheng 0 siblings, 0 replies; 14+ messages in thread From: Icenowy Zheng @ 2020-09-23 0:58 UTC (permalink / raw) To: Rob Herring, Maxime Ripard, Chen-Yu Tsai Cc: devicetree, linux-arm-kernel, linux-kernel, linux-sunxi, Icenowy Zheng The CSI1 controller of V3/V3s/S3/S3L chips is used for parallel CSI. Add the device tree node of it. Signed-off-by: Icenowy Zheng <icenowy@aosc.io> --- arch/arm/boot/dts/sun8i-v3s.dtsi | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/arch/arm/boot/dts/sun8i-v3s.dtsi b/arch/arm/boot/dts/sun8i-v3s.dtsi index 4cfdf193cf88..3e079973672d 100644 --- a/arch/arm/boot/dts/sun8i-v3s.dtsi +++ b/arch/arm/boot/dts/sun8i-v3s.dtsi @@ -488,6 +488,18 @@ spi0: spi@1c68000 { #size-cells = <0>; }; + csi1: camera@1cb4000 { + compatible = "allwinner,sun8i-v3s-csi"; + reg = <0x01cb4000 0x3000>; + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_CSI>, + <&ccu CLK_CSI1_SCLK>, + <&ccu CLK_DRAM_CSI>; + clock-names = "bus", "mod", "ram"; + resets = <&ccu RST_BUS_CSI>; + status = "disabled"; + }; + gic: interrupt-controller@1c81000 { compatible = "arm,gic-400"; reg = <0x01c81000 0x1000>, -- 2.27.0 ^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 4/7] ARM: dts: sun8i: V3/V3s/S3/S3L: add pinctrl for 8-bit parallel CSI 2020-09-23 0:57 [PATCH 0/7] Pine64 PineCube support Icenowy Zheng 2020-09-23 0:57 ` [PATCH 1/7] ARM: dts: sun8i: V3/V3s/S3/S3L: add Ethernet support Icenowy Zheng 2020-09-23 0:58 ` [PATCH 2/7] ARM: dts: sun8i: V3/V3s/S3/S3L: add pinctrl for UART2 RX/TX Icenowy Zheng @ 2020-09-23 1:00 ` Icenowy Zheng 2020-09-23 1:00 ` [PATCH 5/7] ARM: dts: sun8i: V3/V3s/S3/S3L: add pinctrl for I2C1 at PE bank Icenowy Zheng 2020-09-23 1:01 ` [PATCH 4/7] ARM: dts: sun8i: V3/V3s/S3/S3L: add pinctrl for 8-bit parallel CSI Icenowy Zheng ` (2 subsequent siblings) 5 siblings, 1 reply; 14+ messages in thread From: Icenowy Zheng @ 2020-09-23 1:00 UTC (permalink / raw) To: Rob Herring, Maxime Ripard, Chen-Yu Tsai Cc: devicetree, linux-arm-kernel, linux-kernel, linux-sunxi, Icenowy Zheng The CSI1 controller of V3/V3s/S3/S3L SoCs is used for parallel CSI. As we're going to add support for Pine64 SCC board, which uses 8-bit parallel CSI (and the MCLK output), add the pinctrl node of 8-bit CSI and MCLK to the DTSI file. Signed-off-by: Icenowy Zheng <icenowy@aosc.io> --- arch/arm/boot/dts/sun8i-v3s.dtsi | 14 ++++++++++++++ 1 file changed, 14 insertions(+) diff --git a/arch/arm/boot/dts/sun8i-v3s.dtsi b/arch/arm/boot/dts/sun8i-v3s.dtsi index 3e079973672d..19fba1a9115b 100644 --- a/arch/arm/boot/dts/sun8i-v3s.dtsi +++ b/arch/arm/boot/dts/sun8i-v3s.dtsi @@ -312,6 +312,20 @@ pio: pinctrl@1c20800 { interrupt-controller; #interrupt-cells = <3>; + /omit-if-no-ref/ + csi1_8bit_pins: csi1-8bit-pins { + pins = "PE0", "PE2", "PE3", "PE8", "PE9", + "PE10", "PE11", "PE12", "PE13", "PE14", + "PE15"; + function = "csi"; + }; + + /omit-if-no-ref/ + csi1_mclk_pin: csi1-mclk-pin { + pins = "PE1"; + function = "csi"; + }; + i2c0_pins: i2c0-pins { pins = "PB6", "PB7"; function = "i2c0"; -- 2.27.0 ^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 5/7] ARM: dts: sun8i: V3/V3s/S3/S3L: add pinctrl for I2C1 at PE bank 2020-09-23 1:00 ` [PATCH 4/7] ARM: dts: sun8i: V3/V3s/S3/S3L: add pinctrl for 8-bit parallel CSI Icenowy Zheng @ 2020-09-23 1:00 ` Icenowy Zheng 0 siblings, 0 replies; 14+ messages in thread From: Icenowy Zheng @ 2020-09-23 1:00 UTC (permalink / raw) To: Rob Herring, Maxime Ripard, Chen-Yu Tsai Cc: devicetree, linux-arm-kernel, linux-kernel, linux-sunxi, Icenowy Zheng I2C1 controller is available at PE bank, usually used for connecting an I2C-controlled camera sensor. Add pinctrl node for it. Signed-off-by: Icenowy Zheng <icenowy@aosc.io> --- arch/arm/boot/dts/sun8i-v3s.dtsi | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/arch/arm/boot/dts/sun8i-v3s.dtsi b/arch/arm/boot/dts/sun8i-v3s.dtsi index 19fba1a9115b..bae8fa9e356a 100644 --- a/arch/arm/boot/dts/sun8i-v3s.dtsi +++ b/arch/arm/boot/dts/sun8i-v3s.dtsi @@ -331,6 +331,12 @@ i2c0_pins: i2c0-pins { function = "i2c0"; }; + /omit-if-no-ref/ + i2c1_pe_pins: i2c1-pe-pins { + pins = "PE21", "PE22"; + function = "i2c1"; + }; + uart0_pb_pins: uart0-pb-pins { pins = "PB8", "PB9"; function = "uart0"; -- 2.27.0 ^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 4/7] ARM: dts: sun8i: V3/V3s/S3/S3L: add pinctrl for 8-bit parallel CSI 2020-09-23 0:57 [PATCH 0/7] Pine64 PineCube support Icenowy Zheng ` (2 preceding siblings ...) 2020-09-23 1:00 ` [PATCH 4/7] ARM: dts: sun8i: V3/V3s/S3/S3L: add pinctrl for 8-bit parallel CSI Icenowy Zheng @ 2020-09-23 1:01 ` Icenowy Zheng 2020-09-23 1:02 ` [PATCH 6/7] dt-bindings: arm: sunxi: add Pine64 PineCube binding Icenowy Zheng 2020-09-25 15:12 ` [PATCH 0/7] Pine64 PineCube support Maxime Ripard 5 siblings, 0 replies; 14+ messages in thread From: Icenowy Zheng @ 2020-09-23 1:01 UTC (permalink / raw) To: Rob Herring, Maxime Ripard, Chen-Yu Tsai Cc: devicetree, linux-arm-kernel, linux-kernel, linux-sunxi, Icenowy Zheng The CSI1 controller of V3/V3s/S3/S3L SoCs is used for parallel CSI. As we're going to add support for Pine64 SCC board, which uses 8-bit parallel CSI (and the MCLK output), add the pinctrl node of 8-bit CSI and MCLK to the DTSI file. Signed-off-by: Icenowy Zheng <icenowy@aosc.io> --- arch/arm/boot/dts/sun8i-v3s.dtsi | 14 ++++++++++++++ 1 file changed, 14 insertions(+) diff --git a/arch/arm/boot/dts/sun8i-v3s.dtsi b/arch/arm/boot/dts/sun8i-v3s.dtsi index 3e079973672d..19fba1a9115b 100644 --- a/arch/arm/boot/dts/sun8i-v3s.dtsi +++ b/arch/arm/boot/dts/sun8i-v3s.dtsi @@ -312,6 +312,20 @@ pio: pinctrl@1c20800 { interrupt-controller; #interrupt-cells = <3>; + /omit-if-no-ref/ + csi1_8bit_pins: csi1-8bit-pins { + pins = "PE0", "PE2", "PE3", "PE8", "PE9", + "PE10", "PE11", "PE12", "PE13", "PE14", + "PE15"; + function = "csi"; + }; + + /omit-if-no-ref/ + csi1_mclk_pin: csi1-mclk-pin { + pins = "PE1"; + function = "csi"; + }; + i2c0_pins: i2c0-pins { pins = "PB6", "PB7"; function = "i2c0"; -- 2.27.0 ^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 6/7] dt-bindings: arm: sunxi: add Pine64 PineCube binding 2020-09-23 0:57 [PATCH 0/7] Pine64 PineCube support Icenowy Zheng ` (3 preceding siblings ...) 2020-09-23 1:01 ` [PATCH 4/7] ARM: dts: sun8i: V3/V3s/S3/S3L: add pinctrl for 8-bit parallel CSI Icenowy Zheng @ 2020-09-23 1:02 ` Icenowy Zheng 2020-09-23 1:02 ` [PATCH 7/7] ARM: dts: sun8i: s3l: add support for Pine64 PineCube IP camera Icenowy Zheng 2020-09-25 15:12 ` [PATCH 0/7] Pine64 PineCube support Maxime Ripard 5 siblings, 1 reply; 14+ messages in thread From: Icenowy Zheng @ 2020-09-23 1:02 UTC (permalink / raw) To: Rob Herring, Maxime Ripard, Chen-Yu Tsai Cc: devicetree, linux-arm-kernel, linux-kernel, linux-sunxi, Icenowy Zheng Document board compatible names for Pine64 PineCube IP camera. Signed-off-by: Icenowy Zheng <icenowy@aosc.io> --- Documentation/devicetree/bindings/arm/sunxi.yaml | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/sunxi.yaml b/Documentation/devicetree/bindings/arm/sunxi.yaml index 5957a22c2e95..584b3fbf6e08 100644 --- a/Documentation/devicetree/bindings/arm/sunxi.yaml +++ b/Documentation/devicetree/bindings/arm/sunxi.yaml @@ -631,6 +631,11 @@ properties: - const: pine64,pine64-plus - const: allwinner,sun50i-a64 + - description: Pine64 PineCube + items: + - const: pine64,pinecube + - const: allwinner,sun8i-v3 + - description: Pine64 PineH64 model A items: - const: pine64,pine-h64 -- 2.27.0 ^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 7/7] ARM: dts: sun8i: s3l: add support for Pine64 PineCube IP camera 2020-09-23 1:02 ` [PATCH 6/7] dt-bindings: arm: sunxi: add Pine64 PineCube binding Icenowy Zheng @ 2020-09-23 1:02 ` Icenowy Zheng 0 siblings, 0 replies; 14+ messages in thread From: Icenowy Zheng @ 2020-09-23 1:02 UTC (permalink / raw) To: Rob Herring, Maxime Ripard, Chen-Yu Tsai Cc: devicetree, linux-arm-kernel, linux-kernel, linux-sunxi, Icenowy Zheng The Pine64 PineCube IP camera is an IP camera with SoChip S3 SoC. It comes with a main board, an expansion board and a camera. The main board features a Micro-USB power-only jack, a USB Type-A port, an Ethernet port connected to the internal PHY of the SoC and a Realtek RTL8189ES SDIO Wi-Fi module. A RGB LCD connector is reserved on the board. The expansion board features a TF slot, a microphone, a speaker connector with on-board amplifier and a few IR LEDs. Add support for the kit, with features on the main board and the expansion board now. Signed-off-by: Icenowy Zheng <icenowy@aosc.io> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/sun8i-s3-pinecube.dts | 235 ++++++++++++++++++++++++ 2 files changed, 236 insertions(+) create mode 100644 arch/arm/boot/dts/sun8i-s3-pinecube.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index e7c59d0c8598..b163c8f1cefc 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -1198,6 +1198,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \ sun8i-r16-parrot.dtb \ sun8i-r40-bananapi-m2-ultra.dtb \ sun8i-s3-lichee-zero-plus.dtb \ + sun8i-s3-pinecube.dtb \ sun8i-t3-cqa3t-bv3.dtb \ sun8i-v3s-licheepi-zero.dtb \ sun8i-v3s-licheepi-zero-dock.dtb \ diff --git a/arch/arm/boot/dts/sun8i-s3-pinecube.dts b/arch/arm/boot/dts/sun8i-s3-pinecube.dts new file mode 100644 index 000000000000..9bab6b7f4014 --- /dev/null +++ b/arch/arm/boot/dts/sun8i-s3-pinecube.dts @@ -0,0 +1,235 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR X11) +/* + * Copyright 2019 Icenowy Zheng <icenowy@aosc.io> + */ + +/dts-v1/; +#include "sun8i-v3.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> + +/ { + model = "PineCube IP Camera"; + compatible = "pine64,pinecube", "allwinner,sun8i-s3"; + + aliases { + serial0 = &uart2; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + leds { + compatible = "gpio-leds"; + + led1 { + label = "pine64:ir:led1"; + gpios = <&pio 1 10 GPIO_ACTIVE_LOW>; /* PB10 */ + }; + + led2 { + label = "pine64:ir:led2"; + gpios = <&pio 1 12 GPIO_ACTIVE_LOW>; /* PB12 */ + }; + }; + + reg_vcc5v0: vcc5v0 { + compatible = "regulator-fixed"; + regulator-name = "vcc5v0"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + reg_vcc_wifi: vcc-wifi { + compatible = "regulator-fixed"; + regulator-name = "vcc-wifi"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&pio 1 2 GPIO_ACTIVE_LOW>; /* PB2 WIFI-EN */ + vin-supply = <®_dcdc3>; + startup-delay-us = <200000>; + }; + + wifi_pwrseq: wifi_pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&pio 1 3 GPIO_ACTIVE_LOW>; /* PB3 WIFI-RST */ + post-power-on-delay-ms = <200>; + }; +}; + +&csi1 { + pinctrl-names = "default"; + pinctrl-0 = <&csi1_8bit_pins>; + status = "okay"; + + port { + #address-cells = <1>; + #size-cells = <0>; + + csi1_ep: endpoint { + remote-endpoint = <&ov5640_ep>; + bus-width = <8>; + hsync-active = <1>; /* Active high */ + vsync-active = <0>; /* Active low */ + data-active = <1>; /* Active high */ + pclk-sample = <1>; /* Rising */ + }; + }; +}; + +&emac { + phy-handle = <&int_mii_phy>; + phy-mode = "mii"; + status = "okay"; +}; + +&i2c0 { + status = "okay"; + + axp209: pmic@34 { + compatible = "x-powers,axp203", + "x-powers,axp209"; + reg = <0x34>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <1>; + }; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pe_pins>; + status = "okay"; + + ov5640: camera@3c { + compatible = "ovti,ov5640"; + reg = <0x3c>; + pinctrl-names = "default"; + pinctrl-0 = <&csi1_mclk_pin>; + clocks = <&ccu CLK_CSI1_MCLK>; + clock-names = "xclk"; + + AVDD-supply = <®_ldo3>; + DOVDD-supply = <®_ldo3>; + DVDD-supply = <®_ldo4>; + reset-gpios = <&pio 4 23 GPIO_ACTIVE_LOW>; /* PE23 */ + powerdown-gpios = <&pio 4 24 GPIO_ACTIVE_HIGH>; /* PE24 */ + + port { + ov5640_ep: endpoint { + remote-endpoint = <&csi1_ep>; + bus-width = <8>; + hsync-active = <1>; /* Active high */ + vsync-active = <0>; /* Active low */ + data-active = <1>; /* Active high */ + pclk-sample = <1>; /* Rising */ + }; + }; + }; +}; + +&lradc { + vref-supply = <®_ldo2>; + status = "okay"; + + button-200 { + label = "Setup"; + linux,code = <KEY_SETUP>; + channel = <0>; + voltage = <190000>; + }; +}; + +&mmc0 { + vmmc-supply = <®_dcdc3>; + bus-width = <4>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; + status = "okay"; +}; + +&mmc1 { + vmmc-supply = <®_vcc_wifi>; + vqmmc-supply = <®_dcdc3>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; +}; + +&pio { + vcc-pd-supply = <®_dcdc3>; + vcc-pe-supply = <®_ldo3>; +}; + +#include "axp209.dtsi" + +&ac_power_supply { + status = "okay"; +}; + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <1250000>; + regulator-name = "vdd-sys-cpu-ephy"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-3v3"; +}; + +®_ldo1 { + regulator-name = "vdd-rtc"; +}; + +®_ldo2 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; +}; + +®_ldo3 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-name = "avdd-dovdd-2v8-csi"; + regulator-soft-start; + regulator-ramp-delay = <1600>; +}; + +®_ldo4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "dvdd-1v8-csi"; +}; + +&spi0 { + status = "okay"; + + flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "winbond,w25q128", "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <40000000>; + }; +}; + +&uart2 { + status = "okay"; +}; + +&usb_otg { + dr_mode = "host"; + status = "okay"; +}; + +&usbphy { + usb0_vbus-supply = <®_vcc5v0>; + status = "okay"; +}; -- 2.27.0 ^ permalink raw reply related [flat|nested] 14+ messages in thread
* Re: [PATCH 0/7] Pine64 PineCube support 2020-09-23 0:57 [PATCH 0/7] Pine64 PineCube support Icenowy Zheng ` (4 preceding siblings ...) 2020-09-23 1:02 ` [PATCH 6/7] dt-bindings: arm: sunxi: add Pine64 PineCube binding Icenowy Zheng @ 2020-09-25 15:12 ` Maxime Ripard 2020-10-03 10:28 ` [linux-sunxi] " Clément Péron 5 siblings, 1 reply; 14+ messages in thread From: Maxime Ripard @ 2020-09-25 15:12 UTC (permalink / raw) To: Icenowy Zheng Cc: Rob Herring, Chen-Yu Tsai, devicetree, linux-arm-kernel, linux-kernel, linux-sunxi [-- Attachment #1: Type: text/plain, Size: 1088 bytes --] Hi, On Wed, Sep 23, 2020 at 08:57:02AM +0800, Icenowy Zheng wrote: > Pine64 PineCube is an IP camera based on Allwinner S3 chip. > > This patchset tries to add support for it. > > In order to make sure the system do not hang when camera is brought up, > a fix to AXP209 driver is needed (sent individually), otherwise the > system will hang because it changes the voltage of LDO2 when LDO4 > tweaking. Queued all the patches for 5.11 > Icenowy Zheng (7): > ARM: dts: sun8i: V3/V3s/S3/S3L: add Ethernet support > ARM: dts: sun8i: V3/V3s/S3/S3L: add pinctrl for UART2 RX/TX > ARM: dts: sun8i: V3/V3s/S3/S3L: add CSI1 device node > ARM: dts: sun8i: V3/V3s/S3/S3L: add pinctrl for 8-bit parallel CSI > ARM: dts: sun8i: V3/V3s/S3/S3L: add pinctrl for I2C1 at PE bank > dt-bindings: arm: sunxi: add Pine64 PineCube binding > ARM: dts: sun8i: s3l: add support for Pine64 PineCube IP camera However, I guess for the next patches to the v3s DTSI we should just have a simpler prefix (like v3), it's really taking a lot of characters here :) Maxime [-- Attachment #2: signature.asc --] [-- Type: application/pgp-signature, Size: 228 bytes --] ^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [linux-sunxi] Re: [PATCH 0/7] Pine64 PineCube support 2020-09-25 15:12 ` [PATCH 0/7] Pine64 PineCube support Maxime Ripard @ 2020-10-03 10:28 ` Clément Péron 2020-10-03 10:31 ` Clément Péron 2020-10-03 10:39 ` Icenowy Zheng 0 siblings, 2 replies; 14+ messages in thread From: Clément Péron @ 2020-10-03 10:28 UTC (permalink / raw) To: Maxime Ripard Cc: Icenowy Zheng, Rob Herring, Chen-Yu Tsai, devicetree, linux-arm-kernel, linux-kernel, linux-sunxi Hi, I was running dtbs_check and found this series introduced new warnings. DTC arch/arm/boot/dts/sun8i-s3-pinecube.dtb DTC arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml CHECK arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml /arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: compatible: ['allwinner,sun8i-v3s-system-control', 'allwinner,sun8i-h3-system-control'] is not valid under any of the given schemas (Possible causes of the failure): /arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: compatible: Additional items are not allowed ('allwinner,sun8i-h3-system-control' was unexpected) /arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun4i-a10-sram-controller' was expected /arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun4i-a10-system-control' was expected /arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun5i-a13-system-control' was expected /arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun7i-a20-system-control' was expected /arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun8i-a23-system-control' was expected /arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun8i-h3-system-control' was expected /arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun8i-r40-system-control' was expected /arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun50i-a64-sram-controller' was expected /arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun50i-a64-system-control' was expected /arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun50i-h5-system-control' was expected /arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun50i-h6-system-control' was expected /arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,suniv-f1c100s-system-control' was expected /arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: compatible:1: 'allwinner,sun4i-a10-system-control' was expected /arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: compatible:1: 'allwinner,sun4i-a10-system-control' was expected /arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: compatible:1: 'allwinner,sun50i-a64-system-control' was expected /arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: compatible:1: 'allwinner,sun4i-a10-system-control' was expected From schema: /Documentation/devicetree/bindings/sram/allwinner,sun4i-a10-system-control.yaml /arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: camera@1cb4000: port: '#address-cells', '#size-cells' do not match any of the regexes: 'pinctrl-[0-9]+' From schema: /Documentation/devicetree/bindings/media/allwinner,sun6i-a31-csi.yaml And also some other boards /arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: system-control@1c00000: compatible: ['allwinner,sun8i-v3s-system-control', 'allwinner,sun8i-h3-system-control'] is not valid under any of the given schemas (Possible causes of the failure): /arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: system-control@1c00000: compatible: Additional items are not allowed ('allwinner,sun8i-h3-system-control' was unexpected) /arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun4i-a10-sram-controller' was expected /arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun4i-a10-system-control' was expected /arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun5i-a13-system-control' was expected /arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun7i-a20-system-control' was expected /arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun8i-a23-system-control' was expected /arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun8i-h3-system-control' was expected /arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun8i-r40-system-control' was expected /arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun50i-a64-sram-controller' was expected /arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun50i-a64-system-control' was expected /arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun50i-h5-system-control' was expected /arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun50i-h6-system-control' was expected /arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,suniv-f1c100s-system-control' was expected /arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: system-control@1c00000: compatible:1: 'allwinner,sun4i-a10-system-control' was expected /arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: system-control@1c00000: compatible:1: 'allwinner,sun4i-a10-system-control' was expected /arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: system-control@1c00000: compatible:1: 'allwinner,sun50i-a64-system-control' was expected /arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: system-control@1c00000: compatible:1: 'allwinner,sun4i-a10-system-control' was expected From schema: /Documentation/devicetree/bindings/sram/allwinner,sun4i-a10-system-control.yaml /arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: system-control@1c00000: compatible: ['allwinner,sun8i-v3s-system-control', 'allwinner,sun8i-h3-system-control'] is not valid under any of the given schemas (Possible causes of the failure): /arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: system-control@1c00000: compatible: Additional items are not allowed ('allwinner,sun8i-h3-system-control' was unexpected) /arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun4i-a10-sram-controller' was expected /arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun4i-a10-system-control' was expected /arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun5i-a13-system-control' was expected /arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun7i-a20-system-control' was expected /arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun8i-a23-system-control' was expected /arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun8i-h3-system-control' was expected /arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun8i-r40-system-control' was expected /arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun50i-a64-sram-controller' was expected /arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun50i-a64-system-control' was expected /arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun50i-h5-system-control' was expected /arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun50i-h6-system-control' was expected /arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,suniv-f1c100s-system-control' was expected /arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: system-control@1c00000: compatible:1: 'allwinner,sun4i-a10-system-control' was expected /arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: system-control@1c00000: compatible:1: 'allwinner,sun4i-a10-system-control' was expected /arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: system-control@1c00000: compatible:1: 'allwinner,sun50i-a64-system-control' was expected /arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: system-control@1c00000: compatible:1: 'allwinner,sun4i-a10-system-control' was expected From schema: /Documentation/devicetree/bindings/sram/allwinner,sun4i-a10-system-control.yaml /arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: system-control@1c00000: compatible: ['allwinner,sun8i-v3s-system-control', 'allwinner,sun8i-h3-system-control'] is not valid under any of the given schemas (Possible causes of the failure): /arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: system-control@1c00000: compatible: Additional items are not allowed ('allwinner,sun8i-h3-system-control' was unexpected) /arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun4i-a10-sram-controller' was expected /arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun4i-a10-system-control' was expected /arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun5i-a13-system-control' was expected /arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun7i-a20-system-control' was expected /arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun8i-a23-system-control' was expected /arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun8i-h3-system-control' was expected /arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun8i-r40-system-control' was expected /arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun50i-a64-sram-controller' was expected /arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun50i-a64-system-control' was expected /arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun50i-h5-system-control' was expected /arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,sun50i-h6-system-control' was expected /arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: system-control@1c00000: compatible:0: 'allwinner,suniv-f1c100s-system-control' was expected /arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: system-control@1c00000: compatible:1: 'allwinner,sun4i-a10-system-control' was expected /arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: system-control@1c00000: compatible:1: 'allwinner,sun4i-a10-system-control' was expected /arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: system-control@1c00000: compatible:1: 'allwinner,sun50i-a64-system-control' was expected /arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: system-control@1c00000: compatible:1: 'allwinner,sun4i-a10-system-control' was expected Regards, Clement On Fri, 25 Sep 2020 at 17:12, Maxime Ripard <maxime@cerno.tech> wrote: > > Hi, > > On Wed, Sep 23, 2020 at 08:57:02AM +0800, Icenowy Zheng wrote: > > Pine64 PineCube is an IP camera based on Allwinner S3 chip. > > > > This patchset tries to add support for it. > > > > In order to make sure the system do not hang when camera is brought up, > > a fix to AXP209 driver is needed (sent individually), otherwise the > > system will hang because it changes the voltage of LDO2 when LDO4 > > tweaking. > > Queued all the patches for 5.11 > > > Icenowy Zheng (7): > > ARM: dts: sun8i: V3/V3s/S3/S3L: add Ethernet support > > ARM: dts: sun8i: V3/V3s/S3/S3L: add pinctrl for UART2 RX/TX > > ARM: dts: sun8i: V3/V3s/S3/S3L: add CSI1 device node > > ARM: dts: sun8i: V3/V3s/S3/S3L: add pinctrl for 8-bit parallel CSI > > ARM: dts: sun8i: V3/V3s/S3/S3L: add pinctrl for I2C1 at PE bank > > dt-bindings: arm: sunxi: add Pine64 PineCube binding > > ARM: dts: sun8i: s3l: add support for Pine64 PineCube IP camera > > However, I guess for the next patches to the v3s DTSI we should just > have a simpler prefix (like v3), it's really taking a lot of characters > here :) > > Maxime > > -- > You received this message because you are subscribed to the Google Groups "linux-sunxi" group. > To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe@googlegroups.com. > To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20200925151241.kfmytlff4grswtzh%40gilmour.lan. ^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [linux-sunxi] Re: [PATCH 0/7] Pine64 PineCube support 2020-10-03 10:28 ` [linux-sunxi] " Clément Péron @ 2020-10-03 10:31 ` Clément Péron 2020-10-03 10:39 ` Icenowy Zheng 1 sibling, 0 replies; 14+ messages in thread From: Clément Péron @ 2020-10-03 10:31 UTC (permalink / raw) To: Maxime Ripard Cc: Icenowy Zheng, Rob Herring, Chen-Yu Tsai, devicetree, linux-arm-kernel, linux-kernel, linux-sunxi > On Fri, 25 Sep 2020 at 17:12, Maxime Ripard <maxime@cerno.tech> wrote: > > > > Hi, > > > > On Wed, Sep 23, 2020 at 08:57:02AM +0800, Icenowy Zheng wrote: > > > Pine64 PineCube is an IP camera based on Allwinner S3 chip. > > > > > > This patchset tries to add support for it. > > > > > > In order to make sure the system do not hang when camera is brought up, > > > a fix to AXP209 driver is needed (sent individually), otherwise the > > > system will hang because it changes the voltage of LDO2 when LDO4 > > > tweaking. > > > > Queued all the patches for 5.11 I was on top of sunxi sunxi/for-next branch Maybe I'm missing some dt-bindings merged in another tree. Sorry if it's a false warning. Regards, Clement > > > > > Icenowy Zheng (7): > > > ARM: dts: sun8i: V3/V3s/S3/S3L: add Ethernet support > > > ARM: dts: sun8i: V3/V3s/S3/S3L: add pinctrl for UART2 RX/TX > > > ARM: dts: sun8i: V3/V3s/S3/S3L: add CSI1 device node > > > ARM: dts: sun8i: V3/V3s/S3/S3L: add pinctrl for 8-bit parallel CSI > > > ARM: dts: sun8i: V3/V3s/S3/S3L: add pinctrl for I2C1 at PE bank > > > dt-bindings: arm: sunxi: add Pine64 PineCube binding > > > ARM: dts: sun8i: s3l: add support for Pine64 PineCube IP camera > > > > However, I guess for the next patches to the v3s DTSI we should just > > have a simpler prefix (like v3), it's really taking a lot of characters > > here :) > > > > Maxime > > > > -- > > You received this message because you are subscribed to the Google Groups "linux-sunxi" group. > > To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe@googlegroups.com. > > To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20200925151241.kfmytlff4grswtzh%40gilmour.lan. ^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [linux-sunxi] Re: [PATCH 0/7] Pine64 PineCube support 2020-10-03 10:28 ` [linux-sunxi] " Clément Péron 2020-10-03 10:31 ` Clément Péron @ 2020-10-03 10:39 ` Icenowy Zheng 2020-10-03 13:37 ` Clément Péron 1 sibling, 1 reply; 14+ messages in thread From: Icenowy Zheng @ 2020-10-03 10:39 UTC (permalink / raw) To: peron.clem, Clément Péron, Maxime Ripard Cc: Rob Herring, Chen-Yu Tsai, devicetree, linux-arm-kernel, linux-kernel, linux-sunxi 于 2020年10月3日 GMT+08:00 下午6:28:03, "Clément Péron" <peron.clem@gmail.com> 写到: >Hi, > >I was running dtbs_check and found this series introduced new warnings. > > DTC arch/arm/boot/dts/sun8i-s3-pinecube.dtb > DTC arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml > CHECK arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml >/arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: >compatible: ['allwinner,sun8i-v3s-system-control', >'allwinner,sun8i-h3-system-control'] is not valid under any of the >given schemas (Possible causes of the failure): >/arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: >compatible: Additional items are not allowed >('allwinner,sun8i-h3-system-control' was unexpected) >/arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: >compatible:0: 'allwinner,sun4i-a10-sram-controller' was expected >/arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: >compatible:0: 'allwinner,sun4i-a10-system-control' was expected >/arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: >compatible:0: 'allwinner,sun5i-a13-system-control' was expected >/arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: >compatible:0: 'allwinner,sun7i-a20-system-control' was expected >/arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: >compatible:0: 'allwinner,sun8i-a23-system-control' was expected >/arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: >compatible:0: 'allwinner,sun8i-h3-system-control' was expected >/arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: >compatible:0: 'allwinner,sun8i-r40-system-control' was expected >/arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: >compatible:0: 'allwinner,sun50i-a64-sram-controller' was expected >/arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: >compatible:0: 'allwinner,sun50i-a64-system-control' was expected >/arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: >compatible:0: 'allwinner,sun50i-h5-system-control' was expected >/arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: >compatible:0: 'allwinner,sun50i-h6-system-control' was expected >/arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: >compatible:0: 'allwinner,suniv-f1c100s-system-control' was expected >/arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: >compatible:1: 'allwinner,sun4i-a10-system-control' was expected >/arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: >compatible:1: 'allwinner,sun4i-a10-system-control' was expected >/arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: >compatible:1: 'allwinner,sun50i-a64-system-control' was expected >/arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: >compatible:1: 'allwinner,sun4i-a10-system-control' was expected > >From schema: >/Documentation/devicetree/bindings/sram/allwinner,sun4i-a10-system-control.yaml >/arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: camera@1cb4000: port: >'#address-cells', '#size-cells' do not match any of the regexes: >'pinctrl-[0-9]+' >From schema: >/Documentation/devicetree/bindings/media/allwinner,sun6i-a31-csi.yaml Is this broken schema? > >And also some other boards >/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: >system-control@1c00000: compatible: >['allwinner,sun8i-v3s-system-control', >'allwinner,sun8i-h3-system-control'] is not valid under any of the >given schemas (Possible causes of the failure): >/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: >system-control@1c00000: compatible: Additional items are not allowed >('allwinner,sun8i-h3-system-control' was unexpected) >/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: >system-control@1c00000: compatible:0: >'allwinner,sun4i-a10-sram-controller' was expected >/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: >system-control@1c00000: compatible:0: >'allwinner,sun4i-a10-system-control' was expected >/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: >system-control@1c00000: compatible:0: >'allwinner,sun5i-a13-system-control' was expected >/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: >system-control@1c00000: compatible:0: >'allwinner,sun7i-a20-system-control' was expected >/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: >system-control@1c00000: compatible:0: >'allwinner,sun8i-a23-system-control' was expected >/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: >system-control@1c00000: compatible:0: >'allwinner,sun8i-h3-system-control' was expected >/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: >system-control@1c00000: compatible:0: >'allwinner,sun8i-r40-system-control' was expected >/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: >system-control@1c00000: compatible:0: >'allwinner,sun50i-a64-sram-controller' was expected >/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: >system-control@1c00000: compatible:0: >'allwinner,sun50i-a64-system-control' was expected >/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: >system-control@1c00000: compatible:0: >'allwinner,sun50i-h5-system-control' was expected >/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: >system-control@1c00000: compatible:0: >'allwinner,sun50i-h6-system-control' was expected >/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: >system-control@1c00000: compatible:0: >'allwinner,suniv-f1c100s-system-control' was expected >/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: >system-control@1c00000: compatible:1: >'allwinner,sun4i-a10-system-control' was expected >/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: >system-control@1c00000: compatible:1: >'allwinner,sun4i-a10-system-control' was expected >/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: >system-control@1c00000: compatible:1: >'allwinner,sun50i-a64-system-control' was expected >/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: >system-control@1c00000: compatible:1: >'allwinner,sun4i-a10-system-control' was expected > >From schema: >/Documentation/devicetree/bindings/sram/allwinner,sun4i-a10-system-control.yaml >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: >system-control@1c00000: compatible: >['allwinner,sun8i-v3s-system-control', >'allwinner,sun8i-h3-system-control'] is not valid under any of the >given schemas (Possible causes of the failure): >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: >system-control@1c00000: compatible: Additional items are not allowed >('allwinner,sun8i-h3-system-control' was unexpected) >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: >system-control@1c00000: compatible:0: >'allwinner,sun4i-a10-sram-controller' was expected >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: >system-control@1c00000: compatible:0: >'allwinner,sun4i-a10-system-control' was expected >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: >system-control@1c00000: compatible:0: >'allwinner,sun5i-a13-system-control' was expected >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: >system-control@1c00000: compatible:0: >'allwinner,sun7i-a20-system-control' was expected >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: >system-control@1c00000: compatible:0: >'allwinner,sun8i-a23-system-control' was expected >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: >system-control@1c00000: compatible:0: >'allwinner,sun8i-h3-system-control' was expected >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: >system-control@1c00000: compatible:0: >'allwinner,sun8i-r40-system-control' was expected >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: >system-control@1c00000: compatible:0: >'allwinner,sun50i-a64-sram-controller' was expected >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: >system-control@1c00000: compatible:0: >'allwinner,sun50i-a64-system-control' was expected >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: >system-control@1c00000: compatible:0: >'allwinner,sun50i-h5-system-control' was expected >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: >system-control@1c00000: compatible:0: >'allwinner,sun50i-h6-system-control' was expected >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: >system-control@1c00000: compatible:0: >'allwinner,suniv-f1c100s-system-control' was expected >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: >system-control@1c00000: compatible:1: >'allwinner,sun4i-a10-system-control' was expected >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: >system-control@1c00000: compatible:1: >'allwinner,sun4i-a10-system-control' was expected >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: >system-control@1c00000: compatible:1: >'allwinner,sun50i-a64-system-control' was expected >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: >system-control@1c00000: compatible:1: >'allwinner,sun4i-a10-system-control' was expected > >From schema: >/Documentation/devicetree/bindings/sram/allwinner,sun4i-a10-system-control.yaml >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: >system-control@1c00000: compatible: >['allwinner,sun8i-v3s-system-control', >'allwinner,sun8i-h3-system-control'] is not valid under any of the >given schemas (Possible causes of the failure): >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: >system-control@1c00000: compatible: Additional items are not allowed >('allwinner,sun8i-h3-system-control' was unexpected) >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: >system-control@1c00000: compatible:0: >'allwinner,sun4i-a10-sram-controller' was expected >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: >system-control@1c00000: compatible:0: >'allwinner,sun4i-a10-system-control' was expected >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: >system-control@1c00000: compatible:0: >'allwinner,sun5i-a13-system-control' was expected >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: >system-control@1c00000: compatible:0: >'allwinner,sun7i-a20-system-control' was expected >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: >system-control@1c00000: compatible:0: >'allwinner,sun8i-a23-system-control' was expected >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: >system-control@1c00000: compatible:0: >'allwinner,sun8i-h3-system-control' was expected >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: >system-control@1c00000: compatible:0: >'allwinner,sun8i-r40-system-control' was expected >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: >system-control@1c00000: compatible:0: >'allwinner,sun50i-a64-sram-controller' was expected >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: >system-control@1c00000: compatible:0: >'allwinner,sun50i-a64-system-control' was expected >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: >system-control@1c00000: compatible:0: >'allwinner,sun50i-h5-system-control' was expected >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: >system-control@1c00000: compatible:0: >'allwinner,sun50i-h6-system-control' was expected >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: >system-control@1c00000: compatible:0: >'allwinner,suniv-f1c100s-system-control' was expected >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: >system-control@1c00000: compatible:1: >'allwinner,sun4i-a10-system-control' was expected >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: >system-control@1c00000: compatible:1: >'allwinner,sun4i-a10-system-control' was expected >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: >system-control@1c00000: compatible:1: >'allwinner,sun50i-a64-system-control' was expected >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: >system-control@1c00000: compatible:1: >'allwinner,sun4i-a10-system-control' was expected > >Regards, >Clement > >On Fri, 25 Sep 2020 at 17:12, Maxime Ripard <maxime@cerno.tech> wrote: >> >> Hi, >> >> On Wed, Sep 23, 2020 at 08:57:02AM +0800, Icenowy Zheng wrote: >> > Pine64 PineCube is an IP camera based on Allwinner S3 chip. >> > >> > This patchset tries to add support for it. >> > >> > In order to make sure the system do not hang when camera is brought >up, >> > a fix to AXP209 driver is needed (sent individually), otherwise the >> > system will hang because it changes the voltage of LDO2 when LDO4 >> > tweaking. >> >> Queued all the patches for 5.11 >> >> > Icenowy Zheng (7): >> > ARM: dts: sun8i: V3/V3s/S3/S3L: add Ethernet support >> > ARM: dts: sun8i: V3/V3s/S3/S3L: add pinctrl for UART2 RX/TX >> > ARM: dts: sun8i: V3/V3s/S3/S3L: add CSI1 device node >> > ARM: dts: sun8i: V3/V3s/S3/S3L: add pinctrl for 8-bit parallel >CSI >> > ARM: dts: sun8i: V3/V3s/S3/S3L: add pinctrl for I2C1 at PE bank >> > dt-bindings: arm: sunxi: add Pine64 PineCube binding >> > ARM: dts: sun8i: s3l: add support for Pine64 PineCube IP camera >> >> However, I guess for the next patches to the v3s DTSI we should just >> have a simpler prefix (like v3), it's really taking a lot of >characters >> here :) >> >> Maxime >> >> -- >> You received this message because you are subscribed to the Google >Groups "linux-sunxi" group. >> To unsubscribe from this group and stop receiving emails from it, >send an email to linux-sunxi+unsubscribe@googlegroups.com. >> To view this discussion on the web, visit >https://groups.google.com/d/msgid/linux-sunxi/20200925151241.kfmytlff4grswtzh%40gilmour.lan. ^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [linux-sunxi] Re: [PATCH 0/7] Pine64 PineCube support 2020-10-03 10:39 ` Icenowy Zheng @ 2020-10-03 13:37 ` Clément Péron 0 siblings, 0 replies; 14+ messages in thread From: Clément Péron @ 2020-10-03 13:37 UTC (permalink / raw) To: Icenowy Zheng Cc: Maxime Ripard, Rob Herring, Chen-Yu Tsai, devicetree, linux-arm-kernel, linux-kernel, linux-sunxi Hi Icenowy, On Sat, 3 Oct 2020 at 12:39, Icenowy Zheng <icenowy@aosc.io> wrote: > > > > 于 2020年10月3日 GMT+08:00 下午6:28:03, "Clément Péron" <peron.clem@gmail.com> 写到: > >Hi, > > > >I was running dtbs_check and found this series introduced new warnings. > > > > DTC arch/arm/boot/dts/sun8i-s3-pinecube.dtb > > DTC arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml > > CHECK arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml > >/arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: > >compatible: ['allwinner,sun8i-v3s-system-control', > >'allwinner,sun8i-h3-system-control'] is not valid under any of the > >given schemas (Possible causes of the failure): > >/arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: > >compatible: Additional items are not allowed > >('allwinner,sun8i-h3-system-control' was unexpected) > >/arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: > >compatible:0: 'allwinner,sun4i-a10-sram-controller' was expected > >/arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: > >compatible:0: 'allwinner,sun4i-a10-system-control' was expected > >/arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: > >compatible:0: 'allwinner,sun5i-a13-system-control' was expected > >/arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: > >compatible:0: 'allwinner,sun7i-a20-system-control' was expected > >/arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: > >compatible:0: 'allwinner,sun8i-a23-system-control' was expected > >/arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: > >compatible:0: 'allwinner,sun8i-h3-system-control' was expected > >/arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: > >compatible:0: 'allwinner,sun8i-r40-system-control' was expected > >/arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: > >compatible:0: 'allwinner,sun50i-a64-sram-controller' was expected > >/arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: > >compatible:0: 'allwinner,sun50i-a64-system-control' was expected > >/arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: > >compatible:0: 'allwinner,sun50i-h5-system-control' was expected > >/arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: > >compatible:0: 'allwinner,sun50i-h6-system-control' was expected > >/arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: > >compatible:0: 'allwinner,suniv-f1c100s-system-control' was expected > >/arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: > >compatible:1: 'allwinner,sun4i-a10-system-control' was expected > >/arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: > >compatible:1: 'allwinner,sun4i-a10-system-control' was expected > >/arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: > >compatible:1: 'allwinner,sun50i-a64-system-control' was expected > >/arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: system-control@1c00000: > >compatible:1: 'allwinner,sun4i-a10-system-control' was expected > > > >From schema: > >/Documentation/devicetree/bindings/sram/allwinner,sun4i-a10-system-control.yaml > >/arch/arm/boot/dts/sun8i-s3-pinecube.dt.yaml: camera@1cb4000: port: > >'#address-cells', '#size-cells' do not match any of the regexes: > >'pinctrl-[0-9]+' > >From schema: > >/Documentation/devicetree/bindings/media/allwinner,sun6i-a31-csi.yaml > > Is this broken schema? I think the #address-cells', '#size-cells' are not required here. I had a quick look at other csi and nobody seems to specify this. Just FYI This is what I did. pip3 install git+https://github.com/devicetree-org/dt-schema.git@master ARCH=arm make sunxi_defconfig ARCH=arm make -j8 dtbs_check Regards, Clement > > > >And also some other boards > >/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: > >system-control@1c00000: compatible: > >['allwinner,sun8i-v3s-system-control', > >'allwinner,sun8i-h3-system-control'] is not valid under any of the > >given schemas (Possible causes of the failure): > >/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: > >system-control@1c00000: compatible: Additional items are not allowed > >('allwinner,sun8i-h3-system-control' was unexpected) > >/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: > >system-control@1c00000: compatible:0: > >'allwinner,sun4i-a10-sram-controller' was expected > >/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: > >system-control@1c00000: compatible:0: > >'allwinner,sun4i-a10-system-control' was expected > >/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: > >system-control@1c00000: compatible:0: > >'allwinner,sun5i-a13-system-control' was expected > >/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: > >system-control@1c00000: compatible:0: > >'allwinner,sun7i-a20-system-control' was expected > >/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: > >system-control@1c00000: compatible:0: > >'allwinner,sun8i-a23-system-control' was expected > >/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: > >system-control@1c00000: compatible:0: > >'allwinner,sun8i-h3-system-control' was expected > >/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: > >system-control@1c00000: compatible:0: > >'allwinner,sun8i-r40-system-control' was expected > >/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: > >system-control@1c00000: compatible:0: > >'allwinner,sun50i-a64-sram-controller' was expected > >/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: > >system-control@1c00000: compatible:0: > >'allwinner,sun50i-a64-system-control' was expected > >/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: > >system-control@1c00000: compatible:0: > >'allwinner,sun50i-h5-system-control' was expected > >/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: > >system-control@1c00000: compatible:0: > >'allwinner,sun50i-h6-system-control' was expected > >/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: > >system-control@1c00000: compatible:0: > >'allwinner,suniv-f1c100s-system-control' was expected > >/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: > >system-control@1c00000: compatible:1: > >'allwinner,sun4i-a10-system-control' was expected > >/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: > >system-control@1c00000: compatible:1: > >'allwinner,sun4i-a10-system-control' was expected > >/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: > >system-control@1c00000: compatible:1: > >'allwinner,sun50i-a64-system-control' was expected > >/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dt.yaml: > >system-control@1c00000: compatible:1: > >'allwinner,sun4i-a10-system-control' was expected > > > >From schema: > >/Documentation/devicetree/bindings/sram/allwinner,sun4i-a10-system-control.yaml > >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: > >system-control@1c00000: compatible: > >['allwinner,sun8i-v3s-system-control', > >'allwinner,sun8i-h3-system-control'] is not valid under any of the > >given schemas (Possible causes of the failure): > >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: > >system-control@1c00000: compatible: Additional items are not allowed > >('allwinner,sun8i-h3-system-control' was unexpected) > >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: > >system-control@1c00000: compatible:0: > >'allwinner,sun4i-a10-sram-controller' was expected > >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: > >system-control@1c00000: compatible:0: > >'allwinner,sun4i-a10-system-control' was expected > >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: > >system-control@1c00000: compatible:0: > >'allwinner,sun5i-a13-system-control' was expected > >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: > >system-control@1c00000: compatible:0: > >'allwinner,sun7i-a20-system-control' was expected > >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: > >system-control@1c00000: compatible:0: > >'allwinner,sun8i-a23-system-control' was expected > >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: > >system-control@1c00000: compatible:0: > >'allwinner,sun8i-h3-system-control' was expected > >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: > >system-control@1c00000: compatible:0: > >'allwinner,sun8i-r40-system-control' was expected > >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: > >system-control@1c00000: compatible:0: > >'allwinner,sun50i-a64-sram-controller' was expected > >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: > >system-control@1c00000: compatible:0: > >'allwinner,sun50i-a64-system-control' was expected > >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: > >system-control@1c00000: compatible:0: > >'allwinner,sun50i-h5-system-control' was expected > >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: > >system-control@1c00000: compatible:0: > >'allwinner,sun50i-h6-system-control' was expected > >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: > >system-control@1c00000: compatible:0: > >'allwinner,suniv-f1c100s-system-control' was expected > >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: > >system-control@1c00000: compatible:1: > >'allwinner,sun4i-a10-system-control' was expected > >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: > >system-control@1c00000: compatible:1: > >'allwinner,sun4i-a10-system-control' was expected > >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: > >system-control@1c00000: compatible:1: > >'allwinner,sun50i-a64-system-control' was expected > >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dt.yaml: > >system-control@1c00000: compatible:1: > >'allwinner,sun4i-a10-system-control' was expected > > > >From schema: > >/Documentation/devicetree/bindings/sram/allwinner,sun4i-a10-system-control.yaml > >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: > >system-control@1c00000: compatible: > >['allwinner,sun8i-v3s-system-control', > >'allwinner,sun8i-h3-system-control'] is not valid under any of the > >given schemas (Possible causes of the failure): > >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: > >system-control@1c00000: compatible: Additional items are not allowed > >('allwinner,sun8i-h3-system-control' was unexpected) > >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: > >system-control@1c00000: compatible:0: > >'allwinner,sun4i-a10-sram-controller' was expected > >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: > >system-control@1c00000: compatible:0: > >'allwinner,sun4i-a10-system-control' was expected > >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: > >system-control@1c00000: compatible:0: > >'allwinner,sun5i-a13-system-control' was expected > >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: > >system-control@1c00000: compatible:0: > >'allwinner,sun7i-a20-system-control' was expected > >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: > >system-control@1c00000: compatible:0: > >'allwinner,sun8i-a23-system-control' was expected > >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: > >system-control@1c00000: compatible:0: > >'allwinner,sun8i-h3-system-control' was expected > >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: > >system-control@1c00000: compatible:0: > >'allwinner,sun8i-r40-system-control' was expected > >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: > >system-control@1c00000: compatible:0: > >'allwinner,sun50i-a64-sram-controller' was expected > >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: > >system-control@1c00000: compatible:0: > >'allwinner,sun50i-a64-system-control' was expected > >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: > >system-control@1c00000: compatible:0: > >'allwinner,sun50i-h5-system-control' was expected > >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: > >system-control@1c00000: compatible:0: > >'allwinner,sun50i-h6-system-control' was expected > >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: > >system-control@1c00000: compatible:0: > >'allwinner,suniv-f1c100s-system-control' was expected > >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: > >system-control@1c00000: compatible:1: > >'allwinner,sun4i-a10-system-control' was expected > >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: > >system-control@1c00000: compatible:1: > >'allwinner,sun4i-a10-system-control' was expected > >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: > >system-control@1c00000: compatible:1: > >'allwinner,sun50i-a64-system-control' was expected > >/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dt.yaml: > >system-control@1c00000: compatible:1: > >'allwinner,sun4i-a10-system-control' was expected > > > >Regards, > >Clement > > > >On Fri, 25 Sep 2020 at 17:12, Maxime Ripard <maxime@cerno.tech> wrote: > >> > >> Hi, > >> > >> On Wed, Sep 23, 2020 at 08:57:02AM +0800, Icenowy Zheng wrote: > >> > Pine64 PineCube is an IP camera based on Allwinner S3 chip. > >> > > >> > This patchset tries to add support for it. > >> > > >> > In order to make sure the system do not hang when camera is brought > >up, > >> > a fix to AXP209 driver is needed (sent individually), otherwise the > >> > system will hang because it changes the voltage of LDO2 when LDO4 > >> > tweaking. > >> > >> Queued all the patches for 5.11 > >> > >> > Icenowy Zheng (7): > >> > ARM: dts: sun8i: V3/V3s/S3/S3L: add Ethernet support > >> > ARM: dts: sun8i: V3/V3s/S3/S3L: add pinctrl for UART2 RX/TX > >> > ARM: dts: sun8i: V3/V3s/S3/S3L: add CSI1 device node > >> > ARM: dts: sun8i: V3/V3s/S3/S3L: add pinctrl for 8-bit parallel > >CSI > >> > ARM: dts: sun8i: V3/V3s/S3/S3L: add pinctrl for I2C1 at PE bank > >> > dt-bindings: arm: sunxi: add Pine64 PineCube binding > >> > ARM: dts: sun8i: s3l: add support for Pine64 PineCube IP camera > >> > >> However, I guess for the next patches to the v3s DTSI we should just > >> have a simpler prefix (like v3), it's really taking a lot of > >characters > >> here :) > >> > >> Maxime > >> > >> -- > >> You received this message because you are subscribed to the Google > >Groups "linux-sunxi" group. > >> To unsubscribe from this group and stop receiving emails from it, > >send an email to linux-sunxi+unsubscribe@googlegroups.com. > >> To view this discussion on the web, visit > >https://groups.google.com/d/msgid/linux-sunxi/20200925151241.kfmytlff4grswtzh%40gilmour.lan. ^ permalink raw reply [flat|nested] 14+ messages in thread
end of thread, other threads:[~2020-10-03 13:37 UTC | newest] Thread overview: 14+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2020-09-23 0:57 [PATCH 0/7] Pine64 PineCube support Icenowy Zheng 2020-09-23 0:57 ` [PATCH 1/7] ARM: dts: sun8i: V3/V3s/S3/S3L: add Ethernet support Icenowy Zheng 2020-09-23 0:58 ` [PATCH 2/7] ARM: dts: sun8i: V3/V3s/S3/S3L: add pinctrl for UART2 RX/TX Icenowy Zheng 2020-09-23 0:58 ` [PATCH 3/7] ARM: dts: sun8i: V3/V3s/S3/S3L: add CSI1 device node Icenowy Zheng 2020-09-23 1:00 ` [PATCH 4/7] ARM: dts: sun8i: V3/V3s/S3/S3L: add pinctrl for 8-bit parallel CSI Icenowy Zheng 2020-09-23 1:00 ` [PATCH 5/7] ARM: dts: sun8i: V3/V3s/S3/S3L: add pinctrl for I2C1 at PE bank Icenowy Zheng 2020-09-23 1:01 ` [PATCH 4/7] ARM: dts: sun8i: V3/V3s/S3/S3L: add pinctrl for 8-bit parallel CSI Icenowy Zheng 2020-09-23 1:02 ` [PATCH 6/7] dt-bindings: arm: sunxi: add Pine64 PineCube binding Icenowy Zheng 2020-09-23 1:02 ` [PATCH 7/7] ARM: dts: sun8i: s3l: add support for Pine64 PineCube IP camera Icenowy Zheng 2020-09-25 15:12 ` [PATCH 0/7] Pine64 PineCube support Maxime Ripard 2020-10-03 10:28 ` [linux-sunxi] " Clément Péron 2020-10-03 10:31 ` Clément Péron 2020-10-03 10:39 ` Icenowy Zheng 2020-10-03 13:37 ` Clément Péron
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).