* [PATCH 1/2] dt-bindings: net: dsa: split generic port definition from dsa.yaml @ 2021-11-12 16:57 Ansuel Smith 2021-11-12 16:57 ` [PATCH 2/2] dt-bindings: net: dsa: qca8k: improve port definition documentation Ansuel Smith 2021-11-29 21:18 ` [PATCH 1/2] dt-bindings: net: dsa: split generic port definition from dsa.yaml Rob Herring 0 siblings, 2 replies; 5+ messages in thread From: Ansuel Smith @ 2021-11-12 16:57 UTC (permalink / raw) To: Andrew Lunn, Vivien Didelot, Florian Fainelli, Vladimir Oltean, David S. Miller, Jakub Kicinski, Rob Herring, John Crispin, netdev, devicetree, linux-kernel Cc: Ansuel Smith Some switch may require to add additional binding to the node port. Move DSA generic port definition to a dedicated yaml to permit this. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> --- .../devicetree/bindings/net/dsa/dsa-port.yaml | 70 +++++++++++++++++++ .../devicetree/bindings/net/dsa/dsa.yaml | 54 +------------- 2 files changed, 72 insertions(+), 52 deletions(-) create mode 100644 Documentation/devicetree/bindings/net/dsa/dsa-port.yaml diff --git a/Documentation/devicetree/bindings/net/dsa/dsa-port.yaml b/Documentation/devicetree/bindings/net/dsa/dsa-port.yaml new file mode 100644 index 000000000000..258df41c9133 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/dsa-port.yaml @@ -0,0 +1,70 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/dsa-port.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Ethernet Switch port Device Tree Bindings + +maintainers: + - Andrew Lunn <andrew@lunn.ch> + - Florian Fainelli <f.fainelli@gmail.com> + - Vivien Didelot <vivien.didelot@gmail.com> + +description: + Ethernet switch port Description + +properties: + reg: + description: Port number + + label: + description: + Describes the label associated with this port, which will become + the netdev name + $ref: /schemas/types.yaml#/definitions/string + + link: + description: + Should be a list of phandles to other switch's DSA port. This + port is used as the outgoing port towards the phandle ports. The + full routing information must be given, not just the one hop + routes to neighbouring switches + $ref: /schemas/types.yaml#/definitions/phandle-array + + ethernet: + description: + Should be a phandle to a valid Ethernet device node. This host + device is what the switch port is connected to + $ref: /schemas/types.yaml#/definitions/phandle + + dsa-tag-protocol: + description: + Instead of the default, the switch will use this tag protocol if + possible. Useful when a device supports multiple protocols and + the default is incompatible with the Ethernet device. + enum: + - dsa + - edsa + - ocelot + - ocelot-8021q + - seville + + phy-handle: true + + phy-mode: true + + fixed-link: true + + mac-address: true + + sfp: true + + managed: true + +required: + - reg + +additionalProperties: true + +... diff --git a/Documentation/devicetree/bindings/net/dsa/dsa.yaml b/Documentation/devicetree/bindings/net/dsa/dsa.yaml index 224cfa45de9a..15ea9ef3def9 100644 --- a/Documentation/devicetree/bindings/net/dsa/dsa.yaml +++ b/Documentation/devicetree/bindings/net/dsa/dsa.yaml @@ -46,58 +46,8 @@ patternProperties: type: object description: Ethernet switch ports - properties: - reg: - description: Port number - - label: - description: - Describes the label associated with this port, which will become - the netdev name - $ref: /schemas/types.yaml#/definitions/string - - link: - description: - Should be a list of phandles to other switch's DSA port. This - port is used as the outgoing port towards the phandle ports. The - full routing information must be given, not just the one hop - routes to neighbouring switches - $ref: /schemas/types.yaml#/definitions/phandle-array - - ethernet: - description: - Should be a phandle to a valid Ethernet device node. This host - device is what the switch port is connected to - $ref: /schemas/types.yaml#/definitions/phandle - - dsa-tag-protocol: - description: - Instead of the default, the switch will use this tag protocol if - possible. Useful when a device supports multiple protocols and - the default is incompatible with the Ethernet device. - enum: - - dsa - - edsa - - ocelot - - ocelot-8021q - - seville - - phy-handle: true - - phy-mode: true - - fixed-link: true - - mac-address: true - - sfp: true - - managed: true - - required: - - reg - - additionalProperties: false + allOf: + - $ref: dsa-port.yaml# oneOf: - required: -- 2.32.0 ^ permalink raw reply related [flat|nested] 5+ messages in thread
* [PATCH 2/2] dt-bindings: net: dsa: qca8k: improve port definition documentation 2021-11-12 16:57 [PATCH 1/2] dt-bindings: net: dsa: split generic port definition from dsa.yaml Ansuel Smith @ 2021-11-12 16:57 ` Ansuel Smith 2021-11-29 21:20 ` Rob Herring 2021-11-29 21:18 ` [PATCH 1/2] dt-bindings: net: dsa: split generic port definition from dsa.yaml Rob Herring 1 sibling, 1 reply; 5+ messages in thread From: Ansuel Smith @ 2021-11-12 16:57 UTC (permalink / raw) To: Andrew Lunn, Vivien Didelot, Florian Fainelli, Vladimir Oltean, David S. Miller, Jakub Kicinski, Rob Herring, John Crispin, netdev, devicetree, linux-kernel Cc: Ansuel Smith Clean and improve port definition for qca8k documentation by referencing the dsa generic port definition and adding the additional specific port definition. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> --- .../devicetree/bindings/net/dsa/qca8k.yaml | 82 ++++++------------- 1 file changed, 23 insertions(+), 59 deletions(-) diff --git a/Documentation/devicetree/bindings/net/dsa/qca8k.yaml b/Documentation/devicetree/bindings/net/dsa/qca8k.yaml index 48de0ace265d..9eb24cdf6cd4 100644 --- a/Documentation/devicetree/bindings/net/dsa/qca8k.yaml +++ b/Documentation/devicetree/bindings/net/dsa/qca8k.yaml @@ -99,65 +99,29 @@ patternProperties: type: object description: Ethernet switch ports - properties: - reg: - description: Port number - - label: - description: - Describes the label associated with this port, which will become - the netdev name - $ref: /schemas/types.yaml#/definitions/string - - link: - description: - Should be a list of phandles to other switch's DSA port. This - port is used as the outgoing port towards the phandle ports. The - full routing information must be given, not just the one hop - routes to neighbouring switches - $ref: /schemas/types.yaml#/definitions/phandle-array - - ethernet: - description: - Should be a phandle to a valid Ethernet device node. This host - device is what the switch port is connected to - $ref: /schemas/types.yaml#/definitions/phandle - - phy-handle: true - - phy-mode: true - - fixed-link: true - - mac-address: true - - sfp: true - - qca,sgmii-rxclk-falling-edge: - $ref: /schemas/types.yaml#/definitions/flag - description: - Set the receive clock phase to falling edge. Mostly commonly used on - the QCA8327 with CPU port 0 set to SGMII. - - qca,sgmii-txclk-falling-edge: - $ref: /schemas/types.yaml#/definitions/flag - description: - Set the transmit clock phase to falling edge. - - qca,sgmii-enable-pll: - $ref: /schemas/types.yaml#/definitions/flag - description: - For SGMII CPU port, explicitly enable PLL, TX and RX chain along with - Signal Detection. On the QCA8327 this should not be enabled, otherwise - the SGMII port will not initialize. When used on the QCA8337, revision 3 - or greater, a warning will be displayed. When the CPU port is set to - SGMII on the QCA8337, it is advised to set this unless a communication - issue is observed. - - required: - - reg - - additionalProperties: false + allOf: + - $ref: dsa-port.yaml# + - properties: + qca,sgmii-rxclk-falling-edge: + $ref: /schemas/types.yaml#/definitions/flag + description: + Set the receive clock phase to falling edge. Mostly commonly used on + the QCA8327 with CPU port 0 set to SGMII. + + qca,sgmii-txclk-falling-edge: + $ref: /schemas/types.yaml#/definitions/flag + description: + Set the transmit clock phase to falling edge. + + qca,sgmii-enable-pll: + $ref: /schemas/types.yaml#/definitions/flag + description: + For SGMII CPU port, explicitly enable PLL, TX and RX chain along with + Signal Detection. On the QCA8327 this should not be enabled, otherwise + the SGMII port will not initialize. When used on the QCA8337, revision 3 + or greater, a warning will be displayed. When the CPU port is set to + SGMII on the QCA8337, it is advised to set this unless a communication + issue is observed. oneOf: - required: -- 2.32.0 ^ permalink raw reply related [flat|nested] 5+ messages in thread
* Re: [PATCH 2/2] dt-bindings: net: dsa: qca8k: improve port definition documentation 2021-11-12 16:57 ` [PATCH 2/2] dt-bindings: net: dsa: qca8k: improve port definition documentation Ansuel Smith @ 2021-11-29 21:20 ` Rob Herring 0 siblings, 0 replies; 5+ messages in thread From: Rob Herring @ 2021-11-29 21:20 UTC (permalink / raw) To: Ansuel Smith Cc: Andrew Lunn, Vivien Didelot, Florian Fainelli, Vladimir Oltean, David S. Miller, Jakub Kicinski, John Crispin, netdev, devicetree, linux-kernel On Fri, Nov 12, 2021 at 05:57:52PM +0100, Ansuel Smith wrote: > Clean and improve port definition for qca8k documentation by referencing > the dsa generic port definition and adding the additional specific port > definition. > > Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> > --- > .../devicetree/bindings/net/dsa/qca8k.yaml | 82 ++++++------------- > 1 file changed, 23 insertions(+), 59 deletions(-) > > diff --git a/Documentation/devicetree/bindings/net/dsa/qca8k.yaml b/Documentation/devicetree/bindings/net/dsa/qca8k.yaml > index 48de0ace265d..9eb24cdf6cd4 100644 > --- a/Documentation/devicetree/bindings/net/dsa/qca8k.yaml > +++ b/Documentation/devicetree/bindings/net/dsa/qca8k.yaml > @@ -99,65 +99,29 @@ patternProperties: > type: object > description: Ethernet switch ports > > - properties: > - reg: > - description: Port number > - > - label: > - description: > - Describes the label associated with this port, which will become > - the netdev name > - $ref: /schemas/types.yaml#/definitions/string > - > - link: > - description: > - Should be a list of phandles to other switch's DSA port. This > - port is used as the outgoing port towards the phandle ports. The > - full routing information must be given, not just the one hop > - routes to neighbouring switches > - $ref: /schemas/types.yaml#/definitions/phandle-array > - > - ethernet: > - description: > - Should be a phandle to a valid Ethernet device node. This host > - device is what the switch port is connected to > - $ref: /schemas/types.yaml#/definitions/phandle > - > - phy-handle: true > - > - phy-mode: true > - > - fixed-link: true > - > - mac-address: true > - > - sfp: true > - > - qca,sgmii-rxclk-falling-edge: > - $ref: /schemas/types.yaml#/definitions/flag > - description: > - Set the receive clock phase to falling edge. Mostly commonly used on > - the QCA8327 with CPU port 0 set to SGMII. > - > - qca,sgmii-txclk-falling-edge: > - $ref: /schemas/types.yaml#/definitions/flag > - description: > - Set the transmit clock phase to falling edge. > - > - qca,sgmii-enable-pll: > - $ref: /schemas/types.yaml#/definitions/flag > - description: > - For SGMII CPU port, explicitly enable PLL, TX and RX chain along with > - Signal Detection. On the QCA8327 this should not be enabled, otherwise > - the SGMII port will not initialize. When used on the QCA8337, revision 3 > - or greater, a warning will be displayed. When the CPU port is set to > - SGMII on the QCA8337, it is advised to set this unless a communication > - issue is observed. > - > - required: > - - reg > - > - additionalProperties: false > + allOf: > + - $ref: dsa-port.yaml# > + - properties: You can drop 'allOf' here too. And add 'unevaluatedProperties: false'. With that, Reviewed-by: Rob Herring <robh@kernel.org> > + qca,sgmii-rxclk-falling-edge: > + $ref: /schemas/types.yaml#/definitions/flag > + description: > + Set the receive clock phase to falling edge. Mostly commonly used on > + the QCA8327 with CPU port 0 set to SGMII. > + > + qca,sgmii-txclk-falling-edge: > + $ref: /schemas/types.yaml#/definitions/flag > + description: > + Set the transmit clock phase to falling edge. > + > + qca,sgmii-enable-pll: > + $ref: /schemas/types.yaml#/definitions/flag > + description: > + For SGMII CPU port, explicitly enable PLL, TX and RX chain along with > + Signal Detection. On the QCA8327 this should not be enabled, otherwise > + the SGMII port will not initialize. When used on the QCA8337, revision 3 > + or greater, a warning will be displayed. When the CPU port is set to > + SGMII on the QCA8337, it is advised to set this unless a communication > + issue is observed. > > oneOf: > - required: > -- > 2.32.0 > > ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH 1/2] dt-bindings: net: dsa: split generic port definition from dsa.yaml 2021-11-12 16:57 [PATCH 1/2] dt-bindings: net: dsa: split generic port definition from dsa.yaml Ansuel Smith 2021-11-12 16:57 ` [PATCH 2/2] dt-bindings: net: dsa: qca8k: improve port definition documentation Ansuel Smith @ 2021-11-29 21:18 ` Rob Herring 2021-11-29 22:24 ` Ansuel Smith 1 sibling, 1 reply; 5+ messages in thread From: Rob Herring @ 2021-11-29 21:18 UTC (permalink / raw) To: Ansuel Smith Cc: Andrew Lunn, Vivien Didelot, Florian Fainelli, Vladimir Oltean, David S. Miller, Jakub Kicinski, John Crispin, netdev, devicetree, linux-kernel On Fri, Nov 12, 2021 at 05:57:51PM +0100, Ansuel Smith wrote: > Some switch may require to add additional binding to the node port. > Move DSA generic port definition to a dedicated yaml to permit this. > > Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> > --- > .../devicetree/bindings/net/dsa/dsa-port.yaml | 70 +++++++++++++++++++ > .../devicetree/bindings/net/dsa/dsa.yaml | 54 +------------- > 2 files changed, 72 insertions(+), 52 deletions(-) > create mode 100644 Documentation/devicetree/bindings/net/dsa/dsa-port.yaml > > diff --git a/Documentation/devicetree/bindings/net/dsa/dsa-port.yaml b/Documentation/devicetree/bindings/net/dsa/dsa-port.yaml > new file mode 100644 > index 000000000000..258df41c9133 > --- /dev/null > +++ b/Documentation/devicetree/bindings/net/dsa/dsa-port.yaml > @@ -0,0 +1,70 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/net/dsa/dsa-port.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Ethernet Switch port Device Tree Bindings > + > +maintainers: > + - Andrew Lunn <andrew@lunn.ch> > + - Florian Fainelli <f.fainelli@gmail.com> > + - Vivien Didelot <vivien.didelot@gmail.com> > + > +description: > + Ethernet switch port Description > + > +properties: > + reg: > + description: Port number > + > + label: > + description: > + Describes the label associated with this port, which will become > + the netdev name > + $ref: /schemas/types.yaml#/definitions/string > + > + link: > + description: > + Should be a list of phandles to other switch's DSA port. This > + port is used as the outgoing port towards the phandle ports. The > + full routing information must be given, not just the one hop > + routes to neighbouring switches > + $ref: /schemas/types.yaml#/definitions/phandle-array > + > + ethernet: > + description: > + Should be a phandle to a valid Ethernet device node. This host > + device is what the switch port is connected to > + $ref: /schemas/types.yaml#/definitions/phandle > + > + dsa-tag-protocol: > + description: > + Instead of the default, the switch will use this tag protocol if > + possible. Useful when a device supports multiple protocols and > + the default is incompatible with the Ethernet device. > + enum: > + - dsa > + - edsa > + - ocelot > + - ocelot-8021q > + - seville > + > + phy-handle: true > + > + phy-mode: true > + > + fixed-link: true > + > + mac-address: true > + > + sfp: true > + > + managed: true > + > +required: > + - reg > + > +additionalProperties: true > + > +... > diff --git a/Documentation/devicetree/bindings/net/dsa/dsa.yaml b/Documentation/devicetree/bindings/net/dsa/dsa.yaml > index 224cfa45de9a..15ea9ef3def9 100644 > --- a/Documentation/devicetree/bindings/net/dsa/dsa.yaml > +++ b/Documentation/devicetree/bindings/net/dsa/dsa.yaml > @@ -46,58 +46,8 @@ patternProperties: > type: object > description: Ethernet switch ports > > - properties: > - reg: > - description: Port number > - > - label: > - description: > - Describes the label associated with this port, which will become > - the netdev name > - $ref: /schemas/types.yaml#/definitions/string > - > - link: > - description: > - Should be a list of phandles to other switch's DSA port. This > - port is used as the outgoing port towards the phandle ports. The > - full routing information must be given, not just the one hop > - routes to neighbouring switches > - $ref: /schemas/types.yaml#/definitions/phandle-array > - > - ethernet: > - description: > - Should be a phandle to a valid Ethernet device node. This host > - device is what the switch port is connected to > - $ref: /schemas/types.yaml#/definitions/phandle > - > - dsa-tag-protocol: > - description: > - Instead of the default, the switch will use this tag protocol if > - possible. Useful when a device supports multiple protocols and > - the default is incompatible with the Ethernet device. > - enum: > - - dsa > - - edsa > - - ocelot > - - ocelot-8021q > - - seville > - > - phy-handle: true > - > - phy-mode: true > - > - fixed-link: true > - > - mac-address: true > - > - sfp: true > - > - managed: true > - > - required: > - - reg > - > - additionalProperties: false > + allOf: > + - $ref: dsa-port.yaml# Don't need 'allOf' here. And you need to add 'unevaluatedProperties: false'. With that, Reviewed-by: Rob Herring <robh@kernel.org> (This needs to go in net-next to avoid conflicts, but given the maintainers didn't apply it already unreviewed they probably expect I will apply it.) ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH 1/2] dt-bindings: net: dsa: split generic port definition from dsa.yaml 2021-11-29 21:18 ` [PATCH 1/2] dt-bindings: net: dsa: split generic port definition from dsa.yaml Rob Herring @ 2021-11-29 22:24 ` Ansuel Smith 0 siblings, 0 replies; 5+ messages in thread From: Ansuel Smith @ 2021-11-29 22:24 UTC (permalink / raw) To: Rob Herring Cc: Andrew Lunn, Vivien Didelot, Florian Fainelli, Vladimir Oltean, David S. Miller, Jakub Kicinski, John Crispin, netdev, devicetree, linux-kernel On Mon, Nov 29, 2021 at 03:18:54PM -0600, Rob Herring wrote: > On Fri, Nov 12, 2021 at 05:57:51PM +0100, Ansuel Smith wrote: > > Some switch may require to add additional binding to the node port. > > Move DSA generic port definition to a dedicated yaml to permit this. > > > > Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> > > --- > > .../devicetree/bindings/net/dsa/dsa-port.yaml | 70 +++++++++++++++++++ > > .../devicetree/bindings/net/dsa/dsa.yaml | 54 +------------- > > 2 files changed, 72 insertions(+), 52 deletions(-) > > create mode 100644 Documentation/devicetree/bindings/net/dsa/dsa-port.yaml > > > > diff --git a/Documentation/devicetree/bindings/net/dsa/dsa-port.yaml b/Documentation/devicetree/bindings/net/dsa/dsa-port.yaml > > new file mode 100644 > > index 000000000000..258df41c9133 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/net/dsa/dsa-port.yaml > > @@ -0,0 +1,70 @@ > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > > +%YAML 1.2 > > +--- > > +$id: http://devicetree.org/schemas/net/dsa/dsa-port.yaml# > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > + > > +title: Ethernet Switch port Device Tree Bindings > > + > > +maintainers: > > + - Andrew Lunn <andrew@lunn.ch> > > + - Florian Fainelli <f.fainelli@gmail.com> > > + - Vivien Didelot <vivien.didelot@gmail.com> > > + > > +description: > > + Ethernet switch port Description > > + > > +properties: > > + reg: > > + description: Port number > > + > > + label: > > + description: > > + Describes the label associated with this port, which will become > > + the netdev name > > + $ref: /schemas/types.yaml#/definitions/string > > + > > + link: > > + description: > > + Should be a list of phandles to other switch's DSA port. This > > + port is used as the outgoing port towards the phandle ports. The > > + full routing information must be given, not just the one hop > > + routes to neighbouring switches > > + $ref: /schemas/types.yaml#/definitions/phandle-array > > + > > + ethernet: > > + description: > > + Should be a phandle to a valid Ethernet device node. This host > > + device is what the switch port is connected to > > + $ref: /schemas/types.yaml#/definitions/phandle > > + > > + dsa-tag-protocol: > > + description: > > + Instead of the default, the switch will use this tag protocol if > > + possible. Useful when a device supports multiple protocols and > > + the default is incompatible with the Ethernet device. > > + enum: > > + - dsa > > + - edsa > > + - ocelot > > + - ocelot-8021q > > + - seville > > + > > + phy-handle: true > > + > > + phy-mode: true > > + > > + fixed-link: true > > + > > + mac-address: true > > + > > + sfp: true > > + > > + managed: true > > + > > +required: > > + - reg > > + > > +additionalProperties: true > > + > > +... > > diff --git a/Documentation/devicetree/bindings/net/dsa/dsa.yaml b/Documentation/devicetree/bindings/net/dsa/dsa.yaml > > index 224cfa45de9a..15ea9ef3def9 100644 > > --- a/Documentation/devicetree/bindings/net/dsa/dsa.yaml > > +++ b/Documentation/devicetree/bindings/net/dsa/dsa.yaml > > @@ -46,58 +46,8 @@ patternProperties: > > type: object > > description: Ethernet switch ports > > > > - properties: > > - reg: > > - description: Port number > > - > > - label: > > - description: > > - Describes the label associated with this port, which will become > > - the netdev name > > - $ref: /schemas/types.yaml#/definitions/string > > - > > - link: > > - description: > > - Should be a list of phandles to other switch's DSA port. This > > - port is used as the outgoing port towards the phandle ports. The > > - full routing information must be given, not just the one hop > > - routes to neighbouring switches > > - $ref: /schemas/types.yaml#/definitions/phandle-array > > - > > - ethernet: > > - description: > > - Should be a phandle to a valid Ethernet device node. This host > > - device is what the switch port is connected to > > - $ref: /schemas/types.yaml#/definitions/phandle > > - > > - dsa-tag-protocol: > > - description: > > - Instead of the default, the switch will use this tag protocol if > > - possible. Useful when a device supports multiple protocols and > > - the default is incompatible with the Ethernet device. > > - enum: > > - - dsa > > - - edsa > > - - ocelot > > - - ocelot-8021q > > - - seville > > - > > - phy-handle: true > > - > > - phy-mode: true > > - > > - fixed-link: true > > - > > - mac-address: true > > - > > - sfp: true > > - > > - managed: true > > - > > - required: > > - - reg > > - > > - additionalProperties: false > > + allOf: > > + - $ref: dsa-port.yaml# > > Don't need 'allOf' here. And you need to add 'unevaluatedProperties: > false'. With that, > > Reviewed-by: Rob Herring <robh@kernel.org> > > (This needs to go in net-next to avoid conflicts, but given the > maintainers didn't apply it already unreviewed they probably expect I > will apply it.) If you want I can push a v2 with the net-next tag. -- Ansuel ^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2021-11-29 22:24 UTC | newest] Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2021-11-12 16:57 [PATCH 1/2] dt-bindings: net: dsa: split generic port definition from dsa.yaml Ansuel Smith 2021-11-12 16:57 ` [PATCH 2/2] dt-bindings: net: dsa: qca8k: improve port definition documentation Ansuel Smith 2021-11-29 21:20 ` Rob Herring 2021-11-29 21:18 ` [PATCH 1/2] dt-bindings: net: dsa: split generic port definition from dsa.yaml Rob Herring 2021-11-29 22:24 ` Ansuel Smith
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).