From: "André Przywara" <andre.przywara@arm.com>
To: icenowy@aosc.io, Rob Herring <robh+dt@kernel.org>,
Maxime Ripard <maxime.ripard@bootlin.com>,
Chen-Yu Tsai <wens@csie.org>,
Linus Walleij <linus.walleij@linaro.org>
Cc: linux-clk@vger.kernel.org, devicetree@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, linux-gpio@vger.kernel.org,
linux-sunxi@googlegroups.com
Subject: Re: [linux-sunxi] [PATCH v2 5/6] arm64: allwinner: h6: add the basical Allwinner H6 DTSI file
Date: Sun, 11 Feb 2018 23:26:23 +0000 [thread overview]
Message-ID: <a4299cac-84c1-6468-c38a-f232d0dbfb8a@arm.com> (raw)
In-Reply-To: <20180203154942.63566-6-icenowy@aosc.io>
Hi,
On 03/02/18 15:49, Icenowy Zheng wrote:
> Allwinner H6 is a new SoC with Cortex-A53 cores from Allwinner, with its
> memory map fully reworked and some high-speed peripherals (PCIe, USB
> 3.0) introduced.
>
> This commit adds the basical DTSI file of it, including the clock
> support and UART support.
Checked the MMIO addresses and the interrupt numbers against the manual.
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Thanks!
Andre.
> ---
> Changes in v2:
> - Add APB1 clock as PIO's APB clock.
> - Switched to SPDX license identifier.
>
> arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 178 +++++++++++++++++++++++++++
> 1 file changed, 178 insertions(+)
> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
>
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
> new file mode 100644
> index 000000000000..d4697bb42496
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
> @@ -0,0 +1,178 @@
> +/*
> + * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
> + *
> + * SPDX-License-Identifier: (GPL-2.0+ or MIT)
> + */
> +
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/clock/sun50i-h6-ccu.h>
> +#include <dt-bindings/reset/sun50i-h6-ccu.h>
> +
> +/ {
> + interrupt-parent = <&gic>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + cpus {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + cpu0: cpu@0 {
> + compatible = "arm,cortex-a53", "arm,armv8";
> + device_type = "cpu";
> + reg = <0>;
> + enable-method = "psci";
> + };
> +
> + cpu1: cpu@1 {
> + compatible = "arm,cortex-a53", "arm,armv8";
> + device_type = "cpu";
> + reg = <1>;
> + enable-method = "psci";
> + };
> +
> + cpu2: cpu@2 {
> + compatible = "arm,cortex-a53", "arm,armv8";
> + device_type = "cpu";
> + reg = <2>;
> + enable-method = "psci";
> + };
> +
> + cpu3: cpu@3 {
> + compatible = "arm,cortex-a53", "arm,armv8";
> + device_type = "cpu";
> + reg = <3>;
> + enable-method = "psci";
> + };
> + };
> +
> + iosc: internal-osc-clk {
> + #clock-cells = <0>;
> + compatible = "fixed-clock";
> + clock-frequency = <16000000>;
> + clock-accuracy = <300000000>;
> + clock-output-names = "iosc";
> + };
> +
> + osc24M: osc24M_clk {
> + #clock-cells = <0>;
> + compatible = "fixed-clock";
> + clock-frequency = <24000000>;
> + clock-output-names = "osc24M";
> + };
> +
> + osc32k: osc32k_clk {
> + #clock-cells = <0>;
> + compatible = "fixed-clock";
> + clock-frequency = <32768>;
> + clock-output-names = "osc32k";
> + };
> +
> + psci {
> + compatible = "arm,psci-0.2";
> + method = "smc";
> + };
> +
> + timer {
> + compatible = "arm,armv8-timer";
> + interrupts = <GIC_PPI 13
> + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
> + <GIC_PPI 14
> + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
> + <GIC_PPI 11
> + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
> + <GIC_PPI 10
> + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
> + };
> +
> + soc {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + ccu: clock@3001000 {
> + compatible = "allwinner,sun50i-h6-ccu";
> + reg = <0x03001000 0x1000>;
> + clocks = <&osc24M>, <&osc32k>;
> + clock-names = "hosc", "losc";
> + #clock-cells = <1>;
> + #reset-cells = <1>;
> + };
> +
> + gic: interrupt-controller@3021000 {
> + compatible = "arm,gic-400";
> + reg = <0x03021000 0x1000>,
> + <0x03022000 0x2000>,
> + <0x03024000 0x2000>,
> + <0x03026000 0x2000>;
> + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
> + interrupt-controller;
> + #interrupt-cells = <3>;
> + };
> +
> + pio: pinctrl@300b000 {
> + compatible = "allwinner,sun50i-h6-pinctrl";
> + reg = <0x0300b000 0x400>;
> + interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_APB1>, <&osc24M>, <&osc32k>;
> + clock-names = "apb", "hosc", "losc";
> + gpio-controller;
> + #gpio-cells = <3>;
> + interrupt-controller;
> + #interrupt-cells = <3>;
> +
> + uart0_ph_pins: uart0-ph {
> + pins = "PH0", "PH1";
> + function = "uart0";
> + };
> + };
> +
> + uart0: serial@5000000 {
> + compatible = "snps,dw-apb-uart";
> + reg = <0x05000000 0x400>;
> + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + clocks = <&ccu CLK_BUS_UART0>;
> + resets = <&ccu RST_BUS_UART0>;
> + status = "disabled";
> + };
> +
> + uart1: serial@5000400 {
> + compatible = "snps,dw-apb-uart";
> + reg = <0x05000400 0x400>;
> + interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + clocks = <&ccu CLK_BUS_UART1>;
> + resets = <&ccu RST_BUS_UART1>;
> + status = "disabled";
> + };
> +
> + uart2: serial@5000800 {
> + compatible = "snps,dw-apb-uart";
> + reg = <0x05000800 0x400>;
> + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + clocks = <&ccu CLK_BUS_UART2>;
> + resets = <&ccu RST_BUS_UART2>;
> + status = "disabled";
> + };
> +
> + uart3: serial@5000c00 {
> + compatible = "snps,dw-apb-uart";
> + reg = <0x05000c00 0x400>;
> + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + clocks = <&ccu CLK_BUS_UART3>;
> + resets = <&ccu RST_BUS_UART3>;
> + status = "disabled";
> + };
> + };
> +};
>
next prev parent reply other threads:[~2018-02-11 23:26 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-02-03 15:49 [PATCH v2 0/6] Initial Allwinner H6 support Icenowy Zheng
2018-02-03 15:49 ` [PATCH v2 3/6] clk: sunxi-ng: Support fixed post-dividers on NKMP style clocks Icenowy Zheng
[not found] ` <20180203154942.63566-1-icenowy-h8G6r0blFSE@public.gmane.org>
2018-02-03 15:49 ` [PATCH v2 1/6] pinctrl: sunxi: support pin controllers with holes among IRQ banks Icenowy Zheng
[not found] ` <20180203154942.63566-2-icenowy-h8G6r0blFSE@public.gmane.org>
2018-02-07 8:51 ` Maxime Ripard
2018-02-03 15:49 ` [PATCH v2 2/6] pinctrl: sunxi: add support for the Allwinner H6 main pin controller Icenowy Zheng
[not found] ` <20180203154942.63566-3-icenowy-h8G6r0blFSE@public.gmane.org>
2018-02-08 20:16 ` Rob Herring
2018-02-13 0:38 ` [linux-sunxi] " André Przywara
2018-02-03 15:49 ` [PATCH v2 4/6] clk: sunxi-ng: add support for the Allwinner H6 CCU Icenowy Zheng
2018-02-07 9:02 ` Maxime Ripard
2018-02-07 9:11 ` Icenowy Zheng
2018-02-07 18:49 ` Maxime Ripard
2018-02-08 20:18 ` Rob Herring
2018-02-03 15:49 ` [PATCH v2 5/6] arm64: allwinner: h6: add the basical Allwinner H6 DTSI file Icenowy Zheng
2018-02-11 23:26 ` André Przywara [this message]
2018-02-12 9:16 ` [linux-sunxi] " Philippe Ombredanne
2018-02-03 15:49 ` [PATCH v2 6/6] arm64: allwinner: h6: add support for Pine H64 board Icenowy Zheng
[not found] ` <20180203154942.63566-7-icenowy-h8G6r0blFSE@public.gmane.org>
2018-02-11 23:26 ` André Przywara
2018-02-22 12:43 ` [PATCH v2 0/6] Initial Allwinner H6 support Linus Walleij
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=a4299cac-84c1-6468-c38a-f232d0dbfb8a@arm.com \
--to=andre.przywara@arm.com \
--cc=devicetree@vger.kernel.org \
--cc=icenowy@aosc.io \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-sunxi@googlegroups.com \
--cc=maxime.ripard@bootlin.com \
--cc=robh+dt@kernel.org \
--cc=wens@csie.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).