[PATCH 41/53] docs: ABI: avoid using UTF-8 chars

[Mauro Carvalho Chehab <mchehab+huawei@kernel.org>]

While UTF-8 characters can be used at the Linux documentation,
the best is to use them only when ASCII doesn't offer a good replacement.
So, replace the occurences of the following UTF-8 characters:

	- U+2013 ('–'): EN DASH
	- U+2018 ('‘'): LEFT SINGLE QUOTATION MARK
	- U+2019 ('’'): RIGHT SINGLE QUOTATION MARK

Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
---
 .../ABI/testing/sysfs-class-chromeos-driver-cros-ec-lightbar  | 2 +-
 Documentation/ABI/testing/sysfs-class-net-cdc_ncm             | 2 +-
 Documentation/ABI/testing/sysfs-devices-platform-ipmi         | 2 +-
 Documentation/ABI/testing/sysfs-devices-platform-trackpoint   | 2 +-
 Documentation/ABI/testing/sysfs-devices-soc                   | 4 ++--
 5 files changed, 6 insertions(+), 6 deletions(-)

diff --git a/Documentation/ABI/testing/sysfs-class-chromeos-driver-cros-ec-lightbar b/Documentation/ABI/testing/sysfs-class-chromeos-driver-cros-ec-lightbar
index 57a037791403..a7fb8f1169f2 100644
--- a/Documentation/ABI/testing/sysfs-class-chromeos-driver-cros-ec-lightbar
+++ b/Documentation/ABI/testing/sysfs-class-chromeos-driver-cros-ec-lightbar
@@ -29,7 +29,7 @@ KernelVersion:	4.2
 Description:
 		This allows you to control each LED segment. If the
 		lightbar is already running one of the automatic
-		sequences, you probably won’t see anything change because
+		sequences, you probably won't see anything change because
 		your color setting will be almost immediately replaced.
 		To get useful results, you should stop the lightbar
 		sequence first.
diff --git a/Documentation/ABI/testing/sysfs-class-net-cdc_ncm b/Documentation/ABI/testing/sysfs-class-net-cdc_ncm
index 06416d0e163d..41a1eef0d0e7 100644
--- a/Documentation/ABI/testing/sysfs-class-net-cdc_ncm
+++ b/Documentation/ABI/testing/sysfs-class-net-cdc_ncm
@@ -93,7 +93,7 @@ Contact:	Bjørn Mork <bjorn@mork.no>
 Description:
 		- Bit 0: 16-bit NTB supported (set to 1)
 		- Bit 1: 32-bit NTB supported
-		- Bits 2 – 15: reserved (reset to zero; must be ignored by host)
+		- Bits 2 - 15: reserved (reset to zero; must be ignored by host)
 
 What:		/sys/class/net/<iface>/cdc_ncm/dwNtbInMaxSize
 Date:		May 2014
diff --git a/Documentation/ABI/testing/sysfs-devices-platform-ipmi b/Documentation/ABI/testing/sysfs-devices-platform-ipmi
index 07df0ddc0b69..3935cdedea0e 100644
--- a/Documentation/ABI/testing/sysfs-devices-platform-ipmi
+++ b/Documentation/ABI/testing/sysfs-devices-platform-ipmi
@@ -52,7 +52,7 @@ Date:		Mar, 2006
 KernelVersion:	v2.6.17
 Contact:	openipmi-developer@lists.sourceforge.net
 Description:
-		(RO) Lists the IPMI ‘logical device’ commands and functions
+		(RO) Lists the IPMI 'logical device' commands and functions
 		that the controller supports that are in addition to the
 		mandatory IPM and Application commands.
 
diff --git a/Documentation/ABI/testing/sysfs-devices-platform-trackpoint b/Documentation/ABI/testing/sysfs-devices-platform-trackpoint
index df11901a6b3d..82a38ac0435c 100644
--- a/Documentation/ABI/testing/sysfs-devices-platform-trackpoint
+++ b/Documentation/ABI/testing/sysfs-devices-platform-trackpoint
@@ -105,7 +105,7 @@ KernelVersion:	3.19
 Contact:	linux-input@vger.kernel.org
 Description:
 		(RW) This parameter controls the period of time to test for a
-		‘hands off’ condition (i.e. when no force is applied) before a
+		'hands off' condition (i.e. when no force is applied) before a
 		drift (noise) calibration occurs.
 
 		IBM Trackpoints have a feature to compensate for drift by
diff --git a/Documentation/ABI/testing/sysfs-devices-soc b/Documentation/ABI/testing/sysfs-devices-soc
index ea999e292f11..7f90c6a44610 100644
--- a/Documentation/ABI/testing/sysfs-devices-soc
+++ b/Documentation/ABI/testing/sysfs-devices-soc
@@ -27,11 +27,11 @@ Description:
 		(e.g. DB8500).
 
 		On many of ARM based silicon with SMCCC v1.2+ compliant firmware
-		this will contain the JEDEC JEP106 manufacturer’s identification
+		this will contain the JEDEC JEP106 manufacturer's identification
 		code. The format is "jep106:XXYY" where XX is identity code and
 		YY is continuation code.
 
-		This manufacturer’s identification code is defined by one
+		This manufacturer's identification code is defined by one
 		or more eight (8) bit fields, each consisting of seven (7)
 		data bits plus one (1) odd parity bit. It is a single field,
 		limiting the possible number of vendors to 126. To expand
-- 
2.30.2