[PATCH AUTOSEL 5.6 169/606] staging: iio: ad2s1210: Fix SPI reading

[PATCH AUTOSEL 5.6 169/606] staging: iio: ad2s1210: Fix SPI reading

[Sasha Levin]

From: Dragos Bogdan <dragos.bogdan@analog.com>

commit 5e4f99a6b788047b0b8a7496c2e0c8f372f6edf2 upstream.

If the serial interface is used, the 8-bit address should be latched using
the rising edge of the WR/FSYNC signal.

This basically means that a CS change is required between the first byte
sent, and the second one.
This change splits the single-transfer transfer of 2 bytes into 2 transfers
with a single byte, and CS change in-between.

Note fixes tag is not accurate, but reflects a point beyond which there
are too many refactors to make backporting straight forward.

Fixes: b19e9ad5e2cb ("staging:iio:resolver:ad2s1210 general driver cleanup.")
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/staging/iio/resolver/ad2s1210.c | 17 ++++++++++++-----
 1 file changed, 12 insertions(+), 5 deletions(-)

diff --git a/drivers/staging/iio/resolver/ad2s1210.c b/drivers/staging/iio/resolver/ad2s1210.c
index 4b25a3a314ed..ed404355ea4c 100644
--- a/drivers/staging/iio/resolver/ad2s1210.c
+++ b/drivers/staging/iio/resolver/ad2s1210.c
@@ -130,17 +130,24 @@ static int ad2s1210_config_write(struct ad2s1210_state *st, u8 data)
 static int ad2s1210_config_read(struct ad2s1210_state *st,
 				unsigned char address)
 {
-	struct spi_transfer xfer = {
-		.len = 2,
-		.rx_buf = st->rx,
-		.tx_buf = st->tx,
+	struct spi_transfer xfers[] = {
+		{
+			.len = 1,
+			.rx_buf = &st->rx[0],
+			.tx_buf = &st->tx[0],
+			.cs_change = 1,
+		}, {
+			.len = 1,
+			.rx_buf = &st->rx[1],
+			.tx_buf = &st->tx[1],
+		},
 	};
 	int ret = 0;
 
 	ad2s1210_set_mode(MOD_CONFIG, st);
 	st->tx[0] = address | AD2S1210_MSB_IS_HIGH;
 	st->tx[1] = AD2S1210_REG_FAULT;
-	ret = spi_sync_transfer(st->sdev, &xfer, 1);
+	ret = spi_sync_transfer(st->sdev, xfers, 2);
 	if (ret < 0)
 		return ret;
 
-- 
2.25.1

[PATCH AUTOSEL 5.6 173/606] iio: adc: stm32-adc: fix device used to request dma

[Sasha Levin]

From: Fabrice Gasnier <fabrice.gasnier@st.com>

commit 52cd91c27f3908b88e8b25aed4a4d20660abcc45 upstream.

DMA channel request should use device struct from platform device struct.
Currently it's using iio device struct. But at this stage when probing,
device struct isn't yet registered (e.g. device_register is done in
iio_device_register). Since commit 71723a96b8b1 ("dmaengine: Create
symlinks between DMA channels and slaves"), a warning message is printed
as the links in sysfs can't be created, due to device isn't yet registered:
- Cannot create DMA slave symlink
- Cannot create DMA dma:rx symlink

Fix this by using device struct from platform device to request dma chan.

Fixes: 2763ea0585c99 ("iio: adc: stm32: add optional dma support")

Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/iio/adc/stm32-adc.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/iio/adc/stm32-adc.c b/drivers/iio/adc/stm32-adc.c
index ae622ee6d08c..dfc3a306c667 100644
--- a/drivers/iio/adc/stm32-adc.c
+++ b/drivers/iio/adc/stm32-adc.c
@@ -1812,18 +1812,18 @@ static int stm32_adc_chan_of_init(struct iio_dev *indio_dev)
 	return 0;
 }
 
-static int stm32_adc_dma_request(struct iio_dev *indio_dev)
+static int stm32_adc_dma_request(struct device *dev, struct iio_dev *indio_dev)
 {
 	struct stm32_adc *adc = iio_priv(indio_dev);
 	struct dma_slave_config config;
 	int ret;
 
-	adc->dma_chan = dma_request_chan(&indio_dev->dev, "rx");
+	adc->dma_chan = dma_request_chan(dev, "rx");
 	if (IS_ERR(adc->dma_chan)) {
 		ret = PTR_ERR(adc->dma_chan);
 		if (ret != -ENODEV) {
 			if (ret != -EPROBE_DEFER)
-				dev_err(&indio_dev->dev,
+				dev_err(dev,
 					"DMA channel request failed with %d\n",
 					ret);
 			return ret;
@@ -1930,7 +1930,7 @@ static int stm32_adc_probe(struct platform_device *pdev)
 	if (ret < 0)
 		return ret;
 
-	ret = stm32_adc_dma_request(indio_dev);
+	ret = stm32_adc_dma_request(dev, indio_dev);
 	if (ret < 0)
 		return ret;
 
-- 
2.25.1

[PATCH AUTOSEL 5.6 174/606] iio: adc: stm32-dfsdm: fix device used to request dma

[Sasha Levin]

From: Fabrice Gasnier <fabrice.gasnier@st.com>

commit b455d06e6fb3c035711e8aab1ca18082ccb15d87 upstream.

DMA channel request should use device struct from platform device struct.
Currently it's using iio device struct. But at this stage when probing,
device struct isn't yet registered (e.g. device_register is done in
iio_device_register). Since commit 71723a96b8b1 ("dmaengine: Create
symlinks between DMA channels and slaves"), a warning message is printed
as the links in sysfs can't be created, due to device isn't yet registered:
- Cannot create DMA slave symlink
- Cannot create DMA dma:rx symlink

Fix this by using device struct from platform device to request dma chan.

Fixes: eca949800d2d ("IIO: ADC: add stm32 DFSDM support for PDM microphone")

Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/iio/adc/stm32-dfsdm-adc.c | 21 +++++++++++----------
 1 file changed, 11 insertions(+), 10 deletions(-)

diff --git a/drivers/iio/adc/stm32-dfsdm-adc.c b/drivers/iio/adc/stm32-dfsdm-adc.c
index 76a60d93fe23..506bf519f64c 100644
--- a/drivers/iio/adc/stm32-dfsdm-adc.c
+++ b/drivers/iio/adc/stm32-dfsdm-adc.c
@@ -62,7 +62,7 @@ enum sd_converter_type {
 
 struct stm32_dfsdm_dev_data {
 	int type;
-	int (*init)(struct iio_dev *indio_dev);
+	int (*init)(struct device *dev, struct iio_dev *indio_dev);
 	unsigned int num_channels;
 	const struct regmap_config *regmap_cfg;
 };
@@ -1365,11 +1365,12 @@ static void stm32_dfsdm_dma_release(struct iio_dev *indio_dev)
 	}
 }
 
-static int stm32_dfsdm_dma_request(struct iio_dev *indio_dev)
+static int stm32_dfsdm_dma_request(struct device *dev,
+				   struct iio_dev *indio_dev)
 {
 	struct stm32_dfsdm_adc *adc = iio_priv(indio_dev);
 
-	adc->dma_chan = dma_request_chan(&indio_dev->dev, "rx");
+	adc->dma_chan = dma_request_chan(dev, "rx");
 	if (IS_ERR(adc->dma_chan)) {
 		int ret = PTR_ERR(adc->dma_chan);
 
@@ -1425,7 +1426,7 @@ static int stm32_dfsdm_adc_chan_init_one(struct iio_dev *indio_dev,
 					  &adc->dfsdm->ch_list[ch->channel]);
 }
 
-static int stm32_dfsdm_audio_init(struct iio_dev *indio_dev)
+static int stm32_dfsdm_audio_init(struct device *dev, struct iio_dev *indio_dev)
 {
 	struct iio_chan_spec *ch;
 	struct stm32_dfsdm_adc *adc = iio_priv(indio_dev);
@@ -1452,10 +1453,10 @@ static int stm32_dfsdm_audio_init(struct iio_dev *indio_dev)
 	indio_dev->num_channels = 1;
 	indio_dev->channels = ch;
 
-	return stm32_dfsdm_dma_request(indio_dev);
+	return stm32_dfsdm_dma_request(dev, indio_dev);
 }
 
-static int stm32_dfsdm_adc_init(struct iio_dev *indio_dev)
+static int stm32_dfsdm_adc_init(struct device *dev, struct iio_dev *indio_dev)
 {
 	struct iio_chan_spec *ch;
 	struct stm32_dfsdm_adc *adc = iio_priv(indio_dev);
@@ -1499,17 +1500,17 @@ static int stm32_dfsdm_adc_init(struct iio_dev *indio_dev)
 	init_completion(&adc->completion);
 
 	/* Optionally request DMA */
-	ret = stm32_dfsdm_dma_request(indio_dev);
+	ret = stm32_dfsdm_dma_request(dev, indio_dev);
 	if (ret) {
 		if (ret != -ENODEV) {
 			if (ret != -EPROBE_DEFER)
-				dev_err(&indio_dev->dev,
+				dev_err(dev,
 					"DMA channel request failed with %d\n",
 					ret);
 			return ret;
 		}
 
-		dev_dbg(&indio_dev->dev, "No DMA support\n");
+		dev_dbg(dev, "No DMA support\n");
 		return 0;
 	}
 
@@ -1622,7 +1623,7 @@ static int stm32_dfsdm_adc_probe(struct platform_device *pdev)
 		adc->dfsdm->fl_list[adc->fl_id].sync_mode = val;
 
 	adc->dev_data = dev_data;
-	ret = dev_data->init(iio);
+	ret = dev_data->init(dev, iio);
 	if (ret < 0)
 		return ret;
 
-- 
2.25.1

[PATCH AUTOSEL 5.6 175/606] iio: sca3000: Remove an erroneous 'get_device()'

[Sasha Levin]

From: Christophe JAILLET <christophe.jaillet@wanadoo.fr>

commit 928edefbc18cd8433f7df235c6e09a9306e7d580 upstream.

This looks really unusual to have a 'get_device()' hidden in a 'dev_err()'
call.
Remove it.

While at it add a missing \n at the end of the message.

Fixes: 574fb258d636 ("Staging: IIO: VTI sca3000 series accelerometer driver (spi)")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/iio/accel/sca3000.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/iio/accel/sca3000.c b/drivers/iio/accel/sca3000.c
index 66d768d971e1..6e429072e44a 100644
--- a/drivers/iio/accel/sca3000.c
+++ b/drivers/iio/accel/sca3000.c
@@ -980,7 +980,7 @@ static int sca3000_read_data(struct sca3000_state *st,
 	st->tx[0] = SCA3000_READ_REG(reg_address_high);
 	ret = spi_sync_transfer(st->us, xfer, ARRAY_SIZE(xfer));
 	if (ret) {
-		dev_err(get_device(&st->us->dev), "problem reading register");
+		dev_err(&st->us->dev, "problem reading register\n");
 		return ret;
 	}
 
-- 
2.25.1

[PATCH AUTOSEL 5.6 176/606] iio: dac: vf610: Fix an error handling path in 'vf610_dac_probe()'

[Sasha Levin]

From: Christophe JAILLET <christophe.jaillet@wanadoo.fr>

commit aad4742fbf0a560c25827adb58695a4497ffc204 upstream.

A call to 'vf610_dac_exit()' is missing in an error handling path.

Fixes: 1b983bf42fad ("iio: dac: vf610_dac: Add IIO DAC driver for Vybrid SoC")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/iio/dac/vf610_dac.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/iio/dac/vf610_dac.c b/drivers/iio/dac/vf610_dac.c
index 71f8a5c471c4..7f1e9317c3f3 100644
--- a/drivers/iio/dac/vf610_dac.c
+++ b/drivers/iio/dac/vf610_dac.c
@@ -223,6 +223,7 @@ static int vf610_dac_probe(struct platform_device *pdev)
 	return 0;
 
 error_iio_device_register:
+	vf610_dac_exit(info);
 	clk_disable_unprepare(info->clk);
 
 	return ret;
-- 
2.25.1

[PATCH AUTOSEL 5.6 177/606] iio: adc: ti-ads8344: Fix channel selection

[Sasha Levin]

From: Gregory CLEMENT <gregory.clement@bootlin.com>

commit bcfa1e253d2e329e1ebab5c89f3c73f6dd17606c upstream.

During initial submission the selection of the channel was done using
the scan_index member of the iio_chan_spec structure. It was an abuse
because this member is supposed to be used with a buffer so it was
removed.

However there was still the need to be able to known how to select a
channel, the correct member to store this information is address.

Thanks to this it is possible to select any other channel than the
channel 0.

Fixes: 8dd2d7c0fed7 ("iio: adc: Add driver for the TI ADS8344 A/DC chips")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/iio/adc/ti-ads8344.c | 8 +++++---
 1 file changed, 5 insertions(+), 3 deletions(-)

diff --git a/drivers/iio/adc/ti-ads8344.c b/drivers/iio/adc/ti-ads8344.c
index abe4b56c847c..8a8792010c20 100644
--- a/drivers/iio/adc/ti-ads8344.c
+++ b/drivers/iio/adc/ti-ads8344.c
@@ -32,16 +32,17 @@ struct ads8344 {
 	u8 rx_buf[3];
 };
 
-#define ADS8344_VOLTAGE_CHANNEL(chan, si)				\
+#define ADS8344_VOLTAGE_CHANNEL(chan, addr)				\
 	{								\
 		.type = IIO_VOLTAGE,					\
 		.indexed = 1,						\
 		.channel = chan,					\
 		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),		\
 		.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE),	\
+		.address = addr,					\
 	}
 
-#define ADS8344_VOLTAGE_CHANNEL_DIFF(chan1, chan2, si)			\
+#define ADS8344_VOLTAGE_CHANNEL_DIFF(chan1, chan2, addr)		\
 	{								\
 		.type = IIO_VOLTAGE,					\
 		.indexed = 1,						\
@@ -50,6 +51,7 @@ struct ads8344 {
 		.differential = 1,					\
 		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),		\
 		.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE),	\
+		.address = addr,					\
 	}
 
 static const struct iio_chan_spec ads8344_channels[] = {
@@ -105,7 +107,7 @@ static int ads8344_read_raw(struct iio_dev *iio,
 	switch (mask) {
 	case IIO_CHAN_INFO_RAW:
 		mutex_lock(&adc->lock);
-		*value = ads8344_adc_conversion(adc, channel->scan_index,
+		*value = ads8344_adc_conversion(adc, channel->address,
 						channel->differential);
 		mutex_unlock(&adc->lock);
 		if (*value < 0)
-- 
2.25.1

[PATCH AUTOSEL 5.6 193/606] iio: imu: st_lsm6dsx: unlock on error in st_lsm6dsx_shub_write_raw()

[Sasha Levin]

From: Dan Carpenter <dan.carpenter@oracle.com>

commit 115c215a7e5753ddf982c8760ce7904dd3fbb8ae upstream.

We need to release a lock if st_lsm6dsx_check_odr() fails, we can't
return directly.

Fixes: 76551a3c3df1 ("iio: imu: st_lsm6dsx: specify slave odr in slv_odr")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)

diff --git a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c
index 64ef07a30726..1cf98195f84d 100644
--- a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c
+++ b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c
@@ -544,8 +544,10 @@ st_lsm6dsx_shub_write_raw(struct iio_dev *iio_dev,
 
 			ref_sensor = iio_priv(hw->iio_devs[ST_LSM6DSX_ID_ACC]);
 			odr = st_lsm6dsx_check_odr(ref_sensor, val, &odr_val);
-			if (odr < 0)
-				return odr;
+			if (odr < 0) {
+				err = odr;
+				goto release;
+			}
 
 			sensor->ext_info.slv_odr = val;
 			sensor->odr = odr;
@@ -557,6 +559,7 @@ st_lsm6dsx_shub_write_raw(struct iio_dev *iio_dev,
 		break;
 	}
 
+release:
 	iio_device_release_direct_mode(iio_dev);
 
 	return err;
-- 
2.25.1