* Re: [PATCH v2] Added AMS tsl2591 driver implementation [not found] <DB8P195MB0728103C5874083BD441AA0D888D9@DB8P195MB0728.EURP195.PROD.OUTLOOK.COM> @ 2021-02-10 14:50 ` Peter Meerwald-Stadler [not found] ` <DB8P195MB0728DA940A9CC57EA2D05F00888B9@DB8P195MB0728.EURP195.PROD.OUTLOOK.COM> 0 siblings, 1 reply; 3+ messages in thread From: Peter Meerwald-Stadler @ 2021-02-10 14:50 UTC (permalink / raw) To: Joe Sandom; +Cc: jic23, Lars-Peter Clausen, linux-iio, linux-kernel > Driver implementation for AMS/TAOS tsl2591 ambient light sensor. please see comments below > > This driver supports configuration via device tree and sysfs. > Supported channels for raw infrared light, raw visible light, > raw combined light and combined lux value. > The driver additionally supports iio events on lower and > upper thresholds. > > This is a very-high sensitivity light-to-digital converter that > transforms light intensity into a digital signal. > > Datasheet Available at: https://ams.com/tsl25911 > > Signed-off-by: Joe Sandom <joe.sandom@outlook.com> > --- > Changes in v2: > - Significant modifications to ensure compatibility with standard userspace ABI > - Removed unneccesary device tree properties where configuration can be > handled either through sysfs or event properties > - Improved readability of code by inlining where appropriate and > modified naming in areas for clarity > - Cleaned up Makefile and Kconfig to follow correct ordering > - Removed noisy print outs and unnecessary use of __func__ > - All chip configuration done in probe before exposing interfaces to > userspace to avoid race conditions > - Removed having events directly from probe, now follows appropriate > event enable path > - Removed channel showing visible light only as no real use case for it. > Channels are now IR (raw), Visible + IR (raw) and Lux. > - Cleaned up binding file to reflect removal of device tree properties > > NOTE: > Apologies that v2 took a while to get submitted, making the changes to > ensure compatibility with the standard userspace ABI took a lot longer > than anticipated! mostly with the conversion of persist cycles to time > in seconds with respect to ADC integration time amongst other things. > > .../bindings/iio/light/amstaos,tsl2591.yaml | 50 + > drivers/iio/light/Kconfig | 11 + > drivers/iio/light/Makefile | 1 + > drivers/iio/light/tsl2591.c | 1247 +++++++++++++++++ > 4 files changed, 1309 insertions(+) > create mode 100644 Documentation/devicetree/bindings/iio/light/amstaos,tsl2591.yaml > create mode 100644 drivers/iio/light/tsl2591.c > > diff --git a/Documentation/devicetree/bindings/iio/light/amstaos,tsl2591.yaml b/Documentation/devicetree/bindings/iio/light/amstaos,tsl2591.yaml > new file mode 100644 > index 000000000000..030d0bbfdc7b > --- /dev/null > +++ b/Documentation/devicetree/bindings/iio/light/amstaos,tsl2591.yaml > @@ -0,0 +1,50 @@ > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/iio/light/tsl2591.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: AMS/TAOS TSL2591 Ambient Light Sensor (ALS) > + > +maintainers: > + - Joe Sandom <joe.sandom@outlook.com> > + > +description: | > + AMS/TAOS TSL2591 is a very-high sensitivity > + light-to-digital converter that transforms light intensity into a digital > + signal. > + > +properties: > + compatible: > + const: amstaos,tsl2591 > + > + reg: > + maxItems: 1 > + > + interrupts: > + maxItems: 1 > + description: > + Interrupt (INT:Pin 2) Active low. Should be set to IRQ_TYPE_EDGE_FALLING. > + interrupt is used to detect if lux value has reached below or above defined Interrupt is it lux always? or just intensity in some cases > + threshold values. > + > +required: > + - compatible > + - reg > + > +additionalProperties: false > + > +examples: > + - | > + #include <dt-bindings/interrupt-controller/irq.h> > + i2c { > + #address-cells = <1>; > + #size-cells = <0>; > + > + tsl2591@29 { > + compatible = "amstaos,tsl2591"; > + reg = <0x29>; > + interrupts = <20 IRQ_TYPE_EDGE_FALLING>; > + }; > + }; > +... > diff --git a/drivers/iio/light/Kconfig b/drivers/iio/light/Kconfig > index 33ad4dd0b5c7..0b0950a94925 100644 > --- a/drivers/iio/light/Kconfig > +++ b/drivers/iio/light/Kconfig > @@ -501,6 +501,17 @@ config TSL2583 > Provides support for the TAOS tsl2580, tsl2581 and tsl2583 devices. > Access ALS data via iio, sysfs. > > +config TSL2591 > + tristate "TAOS TSL2591 ambient light sensor" > + depends on I2C > + help > + Select Y here for support of the AMS/TAOS TSL2591 ambient light sensor, > + featuring visible and infrared lux output. Access als data via I think lux is defined for visible light only? als -> ALS > + iio and sysfs. Supports iio_events. > + > + To compile this driver as a module, select M: the > + module will be called tsl2591. > + > config TSL2772 > tristate "TAOS TSL/TMD2x71 and TSL/TMD2x72 Family of light and proximity sensors" > depends on I2C > diff --git a/drivers/iio/light/Makefile b/drivers/iio/light/Makefile > index ea376deaca54..d10912faf964 100644 > --- a/drivers/iio/light/Makefile > +++ b/drivers/iio/light/Makefile > @@ -48,6 +48,7 @@ obj-$(CONFIG_ST_UVIS25_SPI) += st_uvis25_spi.o > obj-$(CONFIG_TCS3414) += tcs3414.o > obj-$(CONFIG_TCS3472) += tcs3472.o > obj-$(CONFIG_TSL2583) += tsl2583.o > +obj-$(CONFIG_TSL2591) += tsl2591.o > obj-$(CONFIG_TSL2772) += tsl2772.o > obj-$(CONFIG_TSL4531) += tsl4531.o > obj-$(CONFIG_US5182D) += us5182d.o > diff --git a/drivers/iio/light/tsl2591.c b/drivers/iio/light/tsl2591.c > new file mode 100644 > index 000000000000..fb402ddabeaf > --- /dev/null > +++ b/drivers/iio/light/tsl2591.c > @@ -0,0 +1,1247 @@ > +// SPDX-License-Identifier: GPL-2.0-or-later > +/* > + * Copyright (C) 2020 Joe Sandom <joe.sandom@outlook.com> > + * > + * Datasheet Available at: https://ams.com/tsl25911 available > + * > + * Device driver for the TAOS TSL2591. This is a very-high sensitivity > + * light-to-digital converter that transforms light intensity into a digital > + * signal. > + */ > + > +#include <linux/debugfs.h> > +#include <linux/delay.h> > +#include <linux/i2c.h> > +#include <linux/interrupt.h> > +#include <linux/kernel.h> > +#include <linux/module.h> > +#include <linux/mutex.h> > +#include <linux/pm_runtime.h> > + > +#include <linux/iio/events.h> > +#include <linux/iio/iio.h> > +#include <linux/iio/sysfs.h> > + > +#define als_time_secs_to_ms(x) (((x) + 1) * 100) > +#define als_time_ms_to_secs(x) (((x) / 100) - 1) maybe UPPERCASE macros? > + > +/* TSL2591 Register Set */ > +#define TSL2591_ENABLE 0x00 > +#define TSL2591_CONTROL 0x01 > +#define TSL2591_AILTL 0x04 > +#define TSL2591_AILTH 0x05 > +#define TSL2591_AIHTL 0x06 > +#define TSL2591_AIHTH 0x07 > +#define TSL2591_NP_AILTL 0x08 > +#define TSL2591_NP_AILTH 0x09 > +#define TSL2591_NP_AIHTL 0x0A > +#define TSL2591_NP_AIHTH 0x0B > +#define TSL2591_PERSIST 0x0C > +#define TSL2591_PACKAGE_ID 0x11 > +#define TSL2591_DEVICE_ID 0x12 > +#define TSL2591_STATUS 0x13 > +#define TSL2591_C0_DATAL 0x14 > +#define TSL2591_C0_DATAH 0x15 > +#define TSL2591_C1_DATAL 0x16 > +#define TSL2591_C1_DATAH 0x17 > + > +/* TSL2591 Command Register Masks */ doesn't look like masks, more like values :) > +#define TSL2591_CMD_NOP 0xA0 > +#define TSL2591_CMD_SF_INTSET 0xE4 > +#define TSL2591_CMD_SF_CALS_I 0xE5 > +#define TSL2591_CMD_SF_CALS_NPI 0xE7 > +#define TSL2591_CMD_SF_CNP_ALSI 0xEA > + > +/* TSL2591 Enable Register Masks */ > +#define TSL2591_PWR_ON 0x01 could use BIT() > +#define TSL2591_PWR_OFF 0x00 > +#define TSL2591_ENABLE_ALS 0x02 > +#define TSL2591_ENABLE_ALS_INT 0x10 > +#define TSL2591_ENABLE_SLEEP_INT 0x40 > +#define TSL2591_ENABLE_NP_INT 0x80 > + > +/* TSL2591 Control Register Masks */ > +#define TSL2591_CTRL_ALS_INTEGRATION_100MS 0x00 > +#define TSL2591_CTRL_ALS_INTEGRATION_200MS 0x01 > +#define TSL2591_CTRL_ALS_INTEGRATION_300MS 0x02 > +#define TSL2591_CTRL_ALS_INTEGRATION_400MS 0x03 > +#define TSL2591_CTRL_ALS_INTEGRATION_500MS 0x04 > +#define TSL2591_CTRL_ALS_INTEGRATION_600MS 0x05 > +#define TSL2591_CTRL_ALS_LOW_GAIN 0x00 > +#define TSL2591_CTRL_ALS_MED_GAIN 0x10 > +#define TSL2591_CTRL_ALS_HIGH_GAIN 0x20 > +#define TSL2591_CTRL_ALS_MAX_GAIN 0x30 > +#define TSL2591_CTRL_SYS_RESET 0x80 > + > +/* TSL2591 Persist Register Masks */ not very mask-y > +#define TSL2591_PRST_ALS_INT_CYCLE_0 0x00 > +#define TSL2591_PRST_ALS_INT_CYCLE_ANY 0x01 > +#define TSL2591_PRST_ALS_INT_CYCLE_2 0x02 > +#define TSL2591_PRST_ALS_INT_CYCLE_3 0x03 > +#define TSL2591_PRST_ALS_INT_CYCLE_5 0x04 > +#define TSL2591_PRST_ALS_INT_CYCLE_10 0x05 > +#define TSL2591_PRST_ALS_INT_CYCLE_15 0x06 > +#define TSL2591_PRST_ALS_INT_CYCLE_20 0x07 > +#define TSL2591_PRST_ALS_INT_CYCLE_25 0x08 > +#define TSL2591_PRST_ALS_INT_CYCLE_30 0x09 > +#define TSL2591_PRST_ALS_INT_CYCLE_35 0x0A > +#define TSL2591_PRST_ALS_INT_CYCLE_40 0x0B > +#define TSL2591_PRST_ALS_INT_CYCLE_45 0x0C > +#define TSL2591_PRST_ALS_INT_CYCLE_50 0x0D > +#define TSL2591_PRST_ALS_INT_CYCLE_55 0x0E > +#define TSL2591_PRST_ALS_INT_CYCLE_60 0x0F > +#define TSL2591_PRST_ALS_INT_CYCLE_MAX TSL2591_PRST_ALS_INT_CYCLE_60 > + > +/* TSL2591 Persist Interrupt Cycle Literals */ > +#define TSL2591_PRST_ALS_INT_CYCLE_1_LIT 1 > +#define TSL2591_PRST_ALS_INT_CYCLE_2_LIT 2 > +#define TSL2591_PRST_ALS_INT_CYCLE_3_LIT 3 > +#define TSL2591_PRST_ALS_INT_CYCLE_5_LIT 5 > +#define TSL2591_PRST_ALS_INT_CYCLE_10_LIT 10 > +#define TSL2591_PRST_ALS_INT_CYCLE_15_LIT 15 > +#define TSL2591_PRST_ALS_INT_CYCLE_20_LIT 20 > +#define TSL2591_PRST_ALS_INT_CYCLE_25_LIT 25 > +#define TSL2591_PRST_ALS_INT_CYCLE_30_LIT 30 > +#define TSL2591_PRST_ALS_INT_CYCLE_35_LIT 35 > +#define TSL2591_PRST_ALS_INT_CYCLE_40_LIT 40 > +#define TSL2591_PRST_ALS_INT_CYCLE_45_LIT 45 > +#define TSL2591_PRST_ALS_INT_CYCLE_50_LIT 50 > +#define TSL2591_PRST_ALS_INT_CYCLE_55_LIT 55 > +#define TSL2591_PRST_ALS_INT_CYCLE_60_LIT 60 > + > +/* TSL2591 PID Register Mask */ > +#define TSL2591_PACKAGE_ID_MASK 0x30 > + > +/* TSL2591 ID Register Mask */ > +#define TSL2591_DEVICE_ID_MASK 0xFF > + > +/* TSL2591 Status Register Masks */ > +#define TSL2591_STS_ALS_VALID 0x01 > +#define TSL2591_STS_ALS_INT 0x10 > +#define TSL2591_STS_NPERS_INT 0x20 > +#define TSL2591_STS_VAL_HIGH 0x01 > + > +/* TSL2591 Constant Values */ > +#define TSL2591_PACKAGE_ID_VAL 0x00 > +#define TSL2591_DEVICE_ID_VAL 0x50 > + > +/* Power off suspend delay time MS */ > +#define TSL2591_POWER_OFF_DELAY_MS 2000 > + > +/* TSL2591 Default Values */ there are not just default values > +#define TSL2591_DEFAULT_ALS_INT_TIME TSL2591_CTRL_ALS_INTEGRATION_300MS > +#define TSL2591_MAX_ALS_INT_TIME_MS 600 > +#define TSL2591_DEFAULT_ALS_GAIN TSL2591_CTRL_ALS_MED_GAIN > +#define TSL2591_NUM_DATA_CHANNELS 4 > +#define TSL2591_DEFAULT_ALS_PERSIST TSL2591_PRST_ALS_INT_CYCLE_ANY > +#define TSL2591_DEFAULT_ALS_LOWER_THRESHOLD 100 > +#define TSL2591_DEFAULT_ALS_UPPER_THRESHOLD 1500 > + > +#define TSL2591_ALS_MAX_VALUE 65535 > +#define TSL2591_ALS_STS_VALID_COUNT 10 > + > +/* LUX Calculations */ > +/* AGAIN values from Adafruits TSL2591 Arduino library */ > +/* https://github.com/adafruit/Adafruit_TSL2591_Library */ > +#define TSL2591_CTRL_ALS_LOW_GAIN_MULTIPLIER 1 > +#define TSL2591_CTRL_ALS_MED_GAIN_MULTIPLIER 25 > +#define TSL2591_CTRL_ALS_HIGH_GAIN_MULTIPLIER 428 > +#define TSL2591_CTRL_ALS_MAX_GAIN_MULTIPLIER 9876 > +#define TSL2591_LUX_COEFFICIENT 408 > + > +static const u8 tsl2591_data_channels[] = { > + TSL2591_C0_DATAL, > + TSL2591_C0_DATAH, > + TSL2591_C1_DATAL, > + TSL2591_C1_DATAH, > +}; > + > +struct tsl2591_als_readings { > + u16 als_ch0; > + u16 als_ch1; > + u16 als_lux_int; > + u16 als_lux_decimal; > +}; > + > +struct tsl2591_settings { _als_settings for consistency? everything seems to relate to ALS anyway > + u8 als_int_time; > + u8 als_gain; > + u8 als_persist; > + u16 als_lower_threshold; > + u16 als_upper_threshold; > +}; > + > +struct tsl2591_chip { > + /* Ambient light sensor mutex */ who would have guessed :) maybe drop comment > + struct mutex als_mutex; > + struct i2c_client *client; > + struct tsl2591_settings als_settings; > + struct tsl2591_als_readings als_readings; > + > + bool events_enabled; > +}; > + > +/* Period table is als persist cycle x integration time setting */ ALS multi-line comment? > +/* Integration times: 100ms, 200ms, 300ms, 400ms, 500ms, 600ms */ > +/* ALS cycles: 1, 2, 3, 5, 10, 20, 25, 30, 35, 40, 45, 50, 55, 60 */ > +static const char * const tsl2591_als_period_list[] = { > + "0.1 0.2 0.3 0.5 1.0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 ", remove space at the end? > + "0.2 0.4 0.6 1.0 2.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0", > + "0.3 0.6 0.9 1.5 3.0 6.0 7.5 9.0 10.5 12.0 13.5 15.0 16.5 18.0", > + "0.4 0.8 1.2 2.0 4.0 8.0 10.0 12.0 14.0 16.0 18.0 20.0 22.0 24.0 ", remove space at the end? > + "0.5 1.0 1.5 2.5 5.0 10.0 12.5 15.0 17.5 20.0 22.5 25.0 27.5 30.0", > + "0.6 1.2 1.8 3.0 6.0 12.0 15.0 18.0 21.0 24.0 27.0 30.0 33.0 36.0", > +}; > + > +static int tsl2591_gain_to_multiplier(const u8 als_gain) const necessary? just a bit unusual... > +{ > + switch (als_gain) { > + case TSL2591_CTRL_ALS_LOW_GAIN: > + return TSL2591_CTRL_ALS_LOW_GAIN_MULTIPLIER; > + case TSL2591_CTRL_ALS_MED_GAIN: > + return TSL2591_CTRL_ALS_MED_GAIN_MULTIPLIER; > + case TSL2591_CTRL_ALS_HIGH_GAIN: > + return TSL2591_CTRL_ALS_HIGH_GAIN_MULTIPLIER; > + case TSL2591_CTRL_ALS_MAX_GAIN: > + return TSL2591_CTRL_ALS_MAX_GAIN_MULTIPLIER; > + default: > + break; maybe have the return -EINVAL right here and save some lines? (here and elsewhere) > + } > + > + return -EINVAL; > +} > + > +static u8 tsl2591_multiplier_to_gain(const u32 multiplier) > +{ > + switch (multiplier) { > + case TSL2591_CTRL_ALS_LOW_GAIN_MULTIPLIER: > + return TSL2591_CTRL_ALS_LOW_GAIN; > + case TSL2591_CTRL_ALS_MED_GAIN_MULTIPLIER: > + return TSL2591_CTRL_ALS_MED_GAIN; > + case TSL2591_CTRL_ALS_HIGH_GAIN_MULTIPLIER: > + return TSL2591_CTRL_ALS_HIGH_GAIN; > + case TSL2591_CTRL_ALS_MAX_GAIN_MULTIPLIER: > + return TSL2591_CTRL_ALS_MAX_GAIN; > + default: > + break; > + } > + > + return -EINVAL; > +} > + > +static int tsl2591_persist_cycle_to_lit(const u8 als_persist) > +{ > + switch (als_persist) { > + case TSL2591_PRST_ALS_INT_CYCLE_ANY: > + return TSL2591_PRST_ALS_INT_CYCLE_1_LIT; > + case TSL2591_PRST_ALS_INT_CYCLE_2: > + return TSL2591_PRST_ALS_INT_CYCLE_2_LIT; > + case TSL2591_PRST_ALS_INT_CYCLE_3: > + return TSL2591_PRST_ALS_INT_CYCLE_3_LIT; > + case TSL2591_PRST_ALS_INT_CYCLE_5: > + return TSL2591_PRST_ALS_INT_CYCLE_5_LIT; > + case TSL2591_PRST_ALS_INT_CYCLE_10: > + return TSL2591_PRST_ALS_INT_CYCLE_10_LIT; > + case TSL2591_PRST_ALS_INT_CYCLE_15: > + return TSL2591_PRST_ALS_INT_CYCLE_15_LIT; > + case TSL2591_PRST_ALS_INT_CYCLE_20: > + return TSL2591_PRST_ALS_INT_CYCLE_20_LIT; > + case TSL2591_PRST_ALS_INT_CYCLE_25: > + return TSL2591_PRST_ALS_INT_CYCLE_25_LIT; > + case TSL2591_PRST_ALS_INT_CYCLE_30: > + return TSL2591_PRST_ALS_INT_CYCLE_30_LIT; > + case TSL2591_PRST_ALS_INT_CYCLE_35: > + return TSL2591_PRST_ALS_INT_CYCLE_35_LIT; > + case TSL2591_PRST_ALS_INT_CYCLE_40: > + return TSL2591_PRST_ALS_INT_CYCLE_40_LIT; > + case TSL2591_PRST_ALS_INT_CYCLE_45: > + return TSL2591_PRST_ALS_INT_CYCLE_45_LIT; > + case TSL2591_PRST_ALS_INT_CYCLE_50: > + return TSL2591_PRST_ALS_INT_CYCLE_50_LIT; > + case TSL2591_PRST_ALS_INT_CYCLE_55: > + return TSL2591_PRST_ALS_INT_CYCLE_55_LIT; > + case TSL2591_PRST_ALS_INT_CYCLE_60: > + return TSL2591_PRST_ALS_INT_CYCLE_60_LIT; > + default: > + break; > + } > + > + return -EINVAL; > +} > + > +static int tsl2591_persist_lit_to_cycle(const u8 als_persist) > +{ > + switch (als_persist) { > + case TSL2591_PRST_ALS_INT_CYCLE_1_LIT: > + return TSL2591_PRST_ALS_INT_CYCLE_ANY; > + case TSL2591_PRST_ALS_INT_CYCLE_2_LIT: > + return TSL2591_PRST_ALS_INT_CYCLE_2; > + case TSL2591_PRST_ALS_INT_CYCLE_3_LIT: > + return TSL2591_PRST_ALS_INT_CYCLE_3; > + case TSL2591_PRST_ALS_INT_CYCLE_5_LIT: > + return TSL2591_PRST_ALS_INT_CYCLE_5; > + case TSL2591_PRST_ALS_INT_CYCLE_10_LIT: > + return TSL2591_PRST_ALS_INT_CYCLE_10; > + case TSL2591_PRST_ALS_INT_CYCLE_15_LIT: > + return TSL2591_PRST_ALS_INT_CYCLE_15; > + case TSL2591_PRST_ALS_INT_CYCLE_20_LIT: > + return TSL2591_PRST_ALS_INT_CYCLE_20; > + case TSL2591_PRST_ALS_INT_CYCLE_25_LIT: > + return TSL2591_PRST_ALS_INT_CYCLE_25; > + case TSL2591_PRST_ALS_INT_CYCLE_30_LIT: > + return TSL2591_PRST_ALS_INT_CYCLE_30; > + case TSL2591_PRST_ALS_INT_CYCLE_35_LIT: > + return TSL2591_PRST_ALS_INT_CYCLE_35; > + case TSL2591_PRST_ALS_INT_CYCLE_40_LIT: > + return TSL2591_PRST_ALS_INT_CYCLE_40; > + case TSL2591_PRST_ALS_INT_CYCLE_45_LIT: > + return TSL2591_PRST_ALS_INT_CYCLE_45; > + case TSL2591_PRST_ALS_INT_CYCLE_50_LIT: > + return TSL2591_PRST_ALS_INT_CYCLE_50; > + case TSL2591_PRST_ALS_INT_CYCLE_55_LIT: > + return TSL2591_PRST_ALS_INT_CYCLE_55; > + case TSL2591_PRST_ALS_INT_CYCLE_60_LIT: > + return TSL2591_PRST_ALS_INT_CYCLE_60; > + default: > + break; > + } > + > + return -EINVAL; > +} > + > +static int tsl2591_compatible_int_time(struct tsl2591_chip *chip, > + u32 als_integration_time) const u32 for consistency? here and elsewhere > +{ > + switch (als_integration_time) { > + case TSL2591_CTRL_ALS_INTEGRATION_100MS: > + case TSL2591_CTRL_ALS_INTEGRATION_200MS: > + case TSL2591_CTRL_ALS_INTEGRATION_300MS: > + case TSL2591_CTRL_ALS_INTEGRATION_400MS: > + case TSL2591_CTRL_ALS_INTEGRATION_500MS: > + case TSL2591_CTRL_ALS_INTEGRATION_600MS: > + chip->als_settings.als_int_time = als_integration_time; > + return 0; > + default: > + break; > + } > + > + return -EINVAL; > +} > + > +static int tsl2591_compatible_gain(struct tsl2591_chip *chip, u8 als_gain) > +{ > + switch (als_gain) { > + case TSL2591_CTRL_ALS_LOW_GAIN: > + case TSL2591_CTRL_ALS_MED_GAIN: > + case TSL2591_CTRL_ALS_HIGH_GAIN: > + case TSL2591_CTRL_ALS_MAX_GAIN: > + chip->als_settings.als_gain = als_gain; > + return 0; > + default: > + break; > + } > + > + return -EINVAL; > +} > + > +static int tsl2591_compatible_als_persist(struct tsl2591_chip *chip, > + u32 als_persist) > +{ > + switch (als_persist) { > + case TSL2591_PRST_ALS_INT_CYCLE_ANY: > + case TSL2591_PRST_ALS_INT_CYCLE_2: > + case TSL2591_PRST_ALS_INT_CYCLE_3: > + case TSL2591_PRST_ALS_INT_CYCLE_5: > + case TSL2591_PRST_ALS_INT_CYCLE_10: > + case TSL2591_PRST_ALS_INT_CYCLE_15: > + case TSL2591_PRST_ALS_INT_CYCLE_20: > + case TSL2591_PRST_ALS_INT_CYCLE_25: > + case TSL2591_PRST_ALS_INT_CYCLE_30: > + case TSL2591_PRST_ALS_INT_CYCLE_35: > + case TSL2591_PRST_ALS_INT_CYCLE_40: > + case TSL2591_PRST_ALS_INT_CYCLE_45: > + case TSL2591_PRST_ALS_INT_CYCLE_50: > + case TSL2591_PRST_ALS_INT_CYCLE_55: > + case TSL2591_PRST_ALS_INT_CYCLE_60: > + chip->als_settings.als_persist = als_persist; > + return 0; > + default: > + break; > + } > + > + return -EINVAL; > +} > + > +static int tsl2591_wait_adc_complete(struct tsl2591_chip *chip) > +{ > + struct i2c_client *client = chip->client; > + struct tsl2591_settings settings = chip->als_settings; > + int delay = als_time_secs_to_ms(settings.als_int_time); > + int ret; > + int i; > + > + if (!delay) > + return -EINVAL; > + > + /* > + * Sleep for als integration time to allow enough time ALS (here and elsewhere) > + * for an ADC read cycle to complete. Check status after > + * delay for als valid > + */ > + msleep(delay); > + > + /* Check for status als valid flag for up to 100ms */ > + for (i = 0; i < TSL2591_ALS_STS_VALID_COUNT; ++i) { > + ret = i2c_smbus_read_byte_data(client, TSL2591_CMD_NOP | > + TSL2591_STATUS); > + if (ret < 0) { > + dev_err(&client->dev, "failed to read register\n"); > + return -EINVAL; > + } > + > + if ((ret & TSL2591_STS_ALS_VALID) == TSL2591_STS_VAL_HIGH) > + break; > + > + if (i == (TSL2591_ALS_STS_VALID_COUNT - 1)) > + return -ENODATA; > + > + usleep_range(9000, 10000); > + } > + > + return 0; > +} > + > +/** > + * tsl2591_read_channel_data() - Reads raw channel data and calculates lux > + * > + * Formula for lux calculation; > + * Derived from Adafruit's TSL2591 library > + * Link: https://github.com/adafruit/Adafruit_TSL2591_Library > + * Counts Per Lux (CPL) = (ATIME_ms * AGAIN) / LUX DF > + * lux = ((C0DATA - C1DATA) * (1 - (C1DATA / C0DATA))) / CPL > + * > + * Scale values to get more representative value of lux i.e. > + * lux = ((C0DATA - C1DATA) * (1000 - ((C1DATA * 1000) / C0DATA))) / CPL > + * > + * Channel 0 = IR + Visible > + * Channel 1 = IR only > + * Visible = Channel 0 - Channel 1 > + * > + */ > +static int tsl2591_read_channel_data(struct iio_dev *indio_dev) > +{ > + struct tsl2591_chip *chip = iio_priv(indio_dev); > + struct tsl2591_settings *settings = &chip->als_settings; > + struct i2c_client *client = chip->client; > + int i; > + int ret; > + u8 channel_data[TSL2591_NUM_DATA_CHANNELS]; > + > + int counts_per_lux; > + int lux; > + int gain_multiplier; > + > + ret = tsl2591_wait_adc_complete(chip); > + if (ret < 0) { > + dev_err(&client->dev, "No data available. Err: %d\n", ret); > + return -ENODATA; return ret; _wait_adc_complete() may also return -EINVAL > + } > + > + for (i = 0; i < TSL2591_NUM_DATA_CHANNELS; ++i) { > + int reg = TSL2591_CMD_NOP | tsl2591_data_channels[i]; > + > + ret = i2c_smbus_read_byte_data(client, TSL2591_CMD_NOP | reg); > + if (ret < 0) { > + dev_err(&client->dev, > + "Failed to read register %#04x\n", reg); > + return -EINVAL; > + } > + channel_data[i] = ret; > + } > + > + chip->als_readings.als_ch0 = > + le16_to_cpup((const __le16 *)&channel_data[0]); > + chip->als_readings.als_ch1 = > + le16_to_cpup((const __le16 *)&channel_data[2]); > + > + dev_dbg(&client->dev, "both: %d\n", chip->als_readings.als_ch0); > + dev_dbg(&client->dev, "ir: %d\n", chip->als_readings.als_ch1); > + > + gain_multiplier = tsl2591_gain_to_multiplier(settings->als_gain); > + if (gain_multiplier < 0) { > + dev_err(&client->dev, "Invalid multiplier. Err: %d\n", > + gain_multiplier); > + return -EINVAL; > + } > + > + /* Calculate counts per lux value */ > + counts_per_lux = (als_time_secs_to_ms(settings->als_int_time) * > + gain_multiplier) / TSL2591_LUX_COEFFICIENT; > + > + dev_dbg(&client->dev, "Counts Per Lux (CPL): %d\n", counts_per_lux); > + > + /* Calculate lux value */ > + lux = ((chip->als_readings.als_ch0 - chip->als_readings.als_ch1) * > + (1000 - ((chip->als_readings.als_ch1 * 1000) / > + chip->als_readings.als_ch0))) / counts_per_lux; > + > + /* Divide by 1000 to get real lux value before scaling */ > + chip->als_readings.als_lux_int = lux / 1000; > + > + /* Get the decimal part of lux reading */ > + chip->als_readings.als_lux_decimal = > + (lux - (chip->als_readings.als_lux_int * 1000)); > + > + dev_dbg(&client->dev, "Raw lux calculation: %d\n", lux); > + > + return ret; > +} > + > +static int tsl2591_set_als_gain_int_time(struct tsl2591_chip *chip) > +{ > + struct i2c_client *client = chip->client; > + struct tsl2591_settings als_settings = chip->als_settings; > + int ret; > + > + ret = i2c_smbus_write_byte_data(client, > + TSL2591_CMD_NOP | TSL2591_CONTROL, > + als_settings.als_int_time | > + als_settings.als_gain); > + if (ret < 0) > + dev_err(&client->dev, "Failed to set als gain & int time\n"); > + > + return ret; > +} > + > +static int tsl2591_set_als_thresholds(struct tsl2591_chip *chip) > +{ > + struct i2c_client *client = chip->client; > + struct tsl2591_settings als_settings = chip->als_settings; > + int ret; > + > + u8 als_lower_l; > + u8 als_lower_h; > + u8 als_upper_l; > + u8 als_upper_h; > + > + if (als_settings.als_lower_threshold >= als_settings.als_upper_threshold) { > + dev_warn(&client->dev, "lower threshold higher than upper\n"); > + return -EINVAL; > + } > + > + if (als_settings.als_upper_threshold > TSL2591_ALS_MAX_VALUE) { > + dev_warn(&client->dev, "upper threshold higher than max\n"); > + return -EINVAL; > + } > + > + als_lower_l = (als_settings.als_lower_threshold & 0x00FF); > + als_lower_h = ((als_settings.als_lower_threshold >> 8) & 0x00FF); > + als_upper_l = (als_settings.als_upper_threshold & 0x00FF); > + als_upper_h = ((als_settings.als_upper_threshold >> 8) & 0x00FF); > + > + dev_dbg(&client->dev, "Setting configuration - als lower l: %#04x\n", > + als_lower_l); > + dev_dbg(&client->dev, "Setting configuration - als lower h: %#04x\n", > + als_lower_h); > + dev_dbg(&client->dev, "Setting configuration - als upper l: %#04x\n", > + als_upper_l); > + dev_dbg(&client->dev, "Setting configuration - als upper h: %#04x\n", > + als_upper_h); > + > + ret = i2c_smbus_write_byte_data(client, TSL2591_CMD_NOP | > + TSL2591_AILTL, als_lower_l); > + if (ret < 0) > + dev_err(&client->dev, "Failed to set als lower threshold\n"); > + > + ret = i2c_smbus_write_byte_data(client, TSL2591_CMD_NOP | > + TSL2591_AILTH, als_lower_h); > + if (ret < 0) > + dev_err(&client->dev, "Failed to set als lower threshold\n"); > + > + ret = i2c_smbus_write_byte_data(client, TSL2591_CMD_NOP | > + TSL2591_AIHTL, als_upper_l); > + if (ret < 0) > + dev_err(&client->dev, "Failed to set als upper threshold\n"); > + > + ret = i2c_smbus_write_byte_data(client, TSL2591_CMD_NOP | > + TSL2591_AIHTH, als_upper_h); > + if (ret < 0) > + dev_err(&client->dev, "Failed to set als upper threshold\n"); > + > + return ret; > +} > + > +static int tsl2591_set_als_persist_cycle(struct tsl2591_chip *chip) > +{ > + struct i2c_client *client = chip->client; > + struct tsl2591_settings als_settings = chip->als_settings; > + int ret; > + > + ret = i2c_smbus_write_byte_data(client, TSL2591_CMD_NOP | > + TSL2591_PERSIST, als_settings.als_persist); > + if (ret < 0) > + dev_err(&client->dev, "Failed to set als persist cycle\n"); > + > + return ret; > +} > + > +static int tsl2591_set_power_state(struct tsl2591_chip *chip, u8 state) > +{ > + struct i2c_client *client = chip->client; > + int ret; > + > + ret = i2c_smbus_write_byte_data(client, TSL2591_CMD_NOP | > + TSL2591_ENABLE, state); > + if (ret < 0) > + dev_err(&client->dev, > + "Failed to set the power state to %#04x\n", state); > + > + return ret; > +} > + > +static int tsl2591_get_power_state(struct tsl2591_chip *chip) > +{ > + struct i2c_client *client = chip->client; > + int ret; > + > + ret = i2c_smbus_read_byte_data(client, TSL2591_CMD_NOP | > + TSL2591_ENABLE); > + if (ret < 0) > + dev_err(&client->dev, "Failed to get power state\n"); > + > + return ret; > +} > + > +static ssize_t in_illuminance_integration_time_show(struct device *dev, tsl2591_ prefix missing > + struct device_attribute *attr, > + char *buf) > +{ > + struct iio_dev *indio_dev = dev_to_iio_dev(dev); > + struct tsl2591_chip *chip = iio_priv(indio_dev); > + int ret; > + > + int als_int_time = als_time_secs_to_ms(chip->als_settings.als_int_time); > + > + mutex_lock(&chip->als_mutex); what purpose does the mutex serve? > + ret = sprintf(buf, "%d\n", als_int_time); > + mutex_unlock(&chip->als_mutex); > + > + return ret; > +} > + > +static ssize_t in_illuminance_integration_time_store(struct device *dev, tsl2591_ prefix > + struct device_attribute *attr, > + const char *buf, size_t len) > +{ > + struct iio_dev *indio_dev = dev_to_iio_dev(dev); > + struct tsl2591_chip *chip = iio_priv(indio_dev); > + struct i2c_client *client = chip->client; > + > + u32 int_time; > + int value; > + > + if (kstrtoint(buf, 0, &value) || !value) > + return -EINVAL; > + > + mutex_lock(&chip->als_mutex); > + > + int_time = als_time_ms_to_secs(value); > + > + if (tsl2591_compatible_int_time(chip, int_time)) > + goto calibrate_error; > + > + if (tsl2591_set_als_gain_int_time(chip)) > + goto calibrate_error; > + > + mutex_unlock(&chip->als_mutex); > + > + return len; > + > +calibrate_error: > + dev_err(&client->dev, "Failed to calibrate sensor\n"); > + mutex_unlock(&chip->als_mutex); > + return -EINVAL; > +} > + > +static ssize_t in_illuminance_calibscale_show(struct device *dev, > + struct device_attribute *attr, > + char *buf) > +{ > + struct iio_dev *indio_dev = dev_to_iio_dev(dev); > + struct tsl2591_chip *chip = iio_priv(indio_dev); > + int ret; > + > + mutex_lock(&chip->als_mutex); > + ret = sprintf(buf, "%d\n", tsl2591_gain_to_multiplier > + (chip->als_settings.als_gain)); > + mutex_unlock(&chip->als_mutex); > + > + return ret; > +} > + > +static ssize_t in_illuminance_calibscale_store(struct device *dev, > + struct device_attribute *attr, > + const char *buf, size_t len) > +{ > + struct iio_dev *indio_dev = dev_to_iio_dev(dev); > + struct tsl2591_chip *chip = iio_priv(indio_dev); > + struct i2c_client *client = chip->client; > + > + u8 gain; > + int value; > + > + if (kstrtoint(buf, 0, &value) || !value) > + return -EINVAL; > + > + mutex_lock(&chip->als_mutex); > + > + gain = tsl2591_multiplier_to_gain(value); > + > + if (tsl2591_compatible_gain(chip, gain)) > + goto calibrate_error; > + > + if (tsl2591_set_als_gain_int_time(chip)) > + goto calibrate_error; > + > + mutex_unlock(&chip->als_mutex); > + > + return len; > + > +calibrate_error: > + dev_err(&client->dev, "Failed to calibrate sensor\n"); > + mutex_unlock(&chip->als_mutex); > + return -EINVAL; > +} > + > +static ssize_t in_illuminance_period_available_show(struct device *dev, > + struct device_attribute *attr, > + char *buf) > +{ > + struct iio_dev *indio_dev = dev_to_iio_dev(dev); > + struct tsl2591_chip *chip = iio_priv(indio_dev); > + int ret; > + > + mutex_lock(&chip->als_mutex); > + ret = snprintf(buf, PAGE_SIZE, "%s\n", > + tsl2591_als_period_list[chip->als_settings.als_int_time]); > + mutex_unlock(&chip->als_mutex); > + > + return ret; > +} > + > +static IIO_CONST_ATTR(in_illuminance_integration_time_available, > + "100 200 300 400 500 600"); > +static IIO_CONST_ATTR(in_illuminance_calibscale_available, > + "1 25 428 9876"); > +static IIO_DEVICE_ATTR_RW(in_illuminance_integration_time, 0); > +static IIO_DEVICE_ATTR_RW(in_illuminance_calibscale, 0); > + > +static struct attribute *tsl2591_sysfs_attrs_ctrl[] = { > + &iio_const_attr_in_illuminance_integration_time_available.dev_attr.attr, > + &iio_const_attr_in_illuminance_calibscale_available.dev_attr.attr, > + &iio_dev_attr_in_illuminance_integration_time.dev_attr.attr, > + &iio_dev_attr_in_illuminance_calibscale.dev_attr.attr, > + NULL > +}; > + > +static const struct attribute_group tsl2591_sysfs_attribute_group = { > + .attrs = tsl2591_sysfs_attrs_ctrl, > +}; > + > +static IIO_DEVICE_ATTR_RO(in_illuminance_period_available, 0); > + > +static struct attribute *tsl2591_event_attrs_ctrl[] = { > + &iio_dev_attr_in_illuminance_period_available.dev_attr.attr, > + NULL > +}; > + > +static const struct attribute_group tsl2591_event_attribute_group = { > + .attrs = tsl2591_event_attrs_ctrl, > +}; > + > +static const struct iio_event_spec tsl2591_events[] = { > + { > + .type = IIO_EV_TYPE_THRESH, > + .dir = IIO_EV_DIR_RISING, > + .mask_separate = BIT(IIO_EV_INFO_VALUE), > + }, { > + .type = IIO_EV_TYPE_THRESH, > + .dir = IIO_EV_DIR_FALLING, > + .mask_separate = BIT(IIO_EV_INFO_VALUE), > + }, { > + .type = IIO_EV_TYPE_THRESH, > + .dir = IIO_EV_DIR_EITHER, > + .mask_separate = BIT(IIO_EV_INFO_PERIOD) | > + BIT(IIO_EV_INFO_ENABLE), > + }, > +}; > + > +static const struct iio_chan_spec tsl2591_channels[] = { > + { > + .type = IIO_INTENSITY, > + .modified = 1, > + .channel2 = IIO_MOD_LIGHT_IR, > + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), > + }, > + { > + .type = IIO_INTENSITY, > + .modified = 1, > + .channel2 = IIO_MOD_LIGHT_BOTH, > + .event_spec = tsl2591_events, > + .num_event_specs = ARRAY_SIZE(tsl2591_events), > + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), > + }, > + { > + .type = IIO_LIGHT, > + .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED), > + }, > +}; > + > +static int tsl2591_read_raw(struct iio_dev *indio_dev, > + struct iio_chan_spec const *chan, > + int *val, int *val2, long mask) > +{ > + struct tsl2591_chip *chip = iio_priv(indio_dev); > + struct i2c_client *client = chip->client; > + int ret; > + > + dev_dbg(&client->dev, "Reading from sensor"); > + > + pm_runtime_get_sync(&chip->client->dev); > + > + mutex_lock(&chip->als_mutex); > + > + ret = -EINVAL; > + switch (mask) { > + case IIO_CHAN_INFO_RAW: > + if (chan->type == IIO_INTENSITY) { > + ret = tsl2591_read_channel_data(indio_dev); > + if (ret < 0) > + break; > + > + if (chan->channel2 == IIO_MOD_LIGHT_BOTH) { > + *val = chip->als_readings.als_ch0; > + ret = IIO_VAL_INT; > + } else if (chan->channel2 == IIO_MOD_LIGHT_IR) { > + *val = chip->als_readings.als_ch1; > + ret = IIO_VAL_INT; > + } else { > + ret = -EINVAL; > + } > + } > + break; > + case IIO_CHAN_INFO_PROCESSED: > + if (chan->type == IIO_LIGHT) { > + ret = tsl2591_read_channel_data(indio_dev); > + if (ret < 0) > + break; > + *val = chip->als_readings.als_lux_int; > + *val2 = (chip->als_readings.als_lux_decimal * 1000); > + ret = IIO_VAL_INT_PLUS_MICRO; > + } > + break; > + } > + > + mutex_unlock(&chip->als_mutex); > + > + pm_runtime_mark_last_busy(&chip->client->dev); > + pm_runtime_put_autosuspend(&chip->client->dev); > + > + return ret; > +} > + > +static int tsl2591_read_event_value(struct iio_dev *indio_dev, > + const struct iio_chan_spec *chan, > + enum iio_event_type type, > + enum iio_event_direction dir, > + enum iio_event_info info, int *val, > + int *val2) > +{ > + struct tsl2591_chip *chip = iio_priv(indio_dev); > + struct i2c_client *client = chip->client; > + int als_persist; > + int period; > + int ret; > + int int_time; > + > + switch (info) { > + case IIO_EV_INFO_VALUE: > + switch (dir) { > + case IIO_EV_DIR_RISING: > + mutex_lock(&chip->als_mutex); > + *val = chip->als_settings.als_upper_threshold; > + mutex_unlock(&chip->als_mutex); > + break; > + case IIO_EV_DIR_FALLING: > + mutex_lock(&chip->als_mutex); > + *val = chip->als_settings.als_lower_threshold; > + mutex_unlock(&chip->als_mutex); > + break; > + default: > + return -EINVAL; > + } > + ret = IIO_VAL_INT; > + break; > + case IIO_EV_INFO_PERIOD: > + mutex_lock(&chip->als_mutex); > + > + ret = i2c_smbus_read_byte_data(client, > + TSL2591_CMD_NOP | TSL2591_PERSIST); > + if (ret <= 0 || ret > TSL2591_PRST_ALS_INT_CYCLE_MAX) > + goto err; > + > + als_persist = tsl2591_persist_cycle_to_lit(ret); > + int_time = als_time_secs_to_ms(chip->als_settings.als_int_time); > + period = als_persist * (int_time * MSEC_PER_SEC); > + > + *val = period / USEC_PER_SEC; > + *val2 = period % USEC_PER_SEC; > + > + mutex_unlock(&chip->als_mutex); > + ret = IIO_VAL_INT_PLUS_MICRO; > + break; > + default: > + return -EINVAL; > + } > + > + return ret; > + > +err: > + mutex_unlock(&chip->als_mutex); > + return -EINVAL; > +} > + > +static int tsl2591_write_event_value(struct iio_dev *indio_dev, > + const struct iio_chan_spec *chan, > + enum iio_event_type type, > + enum iio_event_direction dir, > + enum iio_event_info info, int val, > + int val2) > +{ > + struct tsl2591_chip *chip = iio_priv(indio_dev); > + int period, int_time, als_cycle; > + > + if (val < 0 || val2 < 0) > + return -EINVAL; > + > + switch (info) { > + case IIO_EV_INFO_VALUE: > + if (val > TSL2591_ALS_MAX_VALUE) > + return -EINVAL; > + /* Lower threshold should not be higher than upper */ > + if (dir == IIO_EV_DIR_FALLING) > + if (val > chip->als_settings.als_upper_threshold) > + return -EINVAL; > + > + switch (dir) { > + case IIO_EV_DIR_RISING: > + mutex_lock(&chip->als_mutex); > + chip->als_settings.als_upper_threshold = val; > + if (tsl2591_set_als_thresholds(chip)) > + goto err; > + mutex_unlock(&chip->als_mutex); > + break; > + case IIO_EV_DIR_FALLING: > + mutex_lock(&chip->als_mutex); > + chip->als_settings.als_lower_threshold = val; > + if (tsl2591_set_als_thresholds(chip)) > + goto err; > + mutex_unlock(&chip->als_mutex); > + break; > + default: > + return -EINVAL; > + } > + break; > + case IIO_EV_INFO_PERIOD: > + mutex_lock(&chip->als_mutex); > + int_time = als_time_secs_to_ms(chip->als_settings.als_int_time); > + if (!val && val2) > + period = (val2 / MSEC_PER_SEC) / int_time; > + else if (val && !val2) > + period = (val * MSEC_PER_SEC) / int_time; > + else if (val && val2) > + period = ((val * MSEC_PER_SEC) + > + (val2 / MSEC_PER_SEC)) / int_time; > + else > + goto err; > + > + als_cycle = tsl2591_persist_lit_to_cycle(period); > + if (als_cycle < 0) > + goto err; > + if (tsl2591_compatible_als_persist(chip, als_cycle)) > + goto err; > + if (tsl2591_set_als_persist_cycle(chip)) > + goto err; > + mutex_unlock(&chip->als_mutex); > + break; > + default: > + return -EINVAL; > + } > + > + return 0; > +err: > + mutex_unlock(&chip->als_mutex); > + return -EINVAL; > +} > + > +static int tsl2591_read_event_config(struct iio_dev *indio_dev, > + const struct iio_chan_spec *chan, > + enum iio_event_type type, > + enum iio_event_direction dir) > +{ > + struct tsl2591_chip *chip = iio_priv(indio_dev); > + int ret; > + > + mutex_lock(&chip->als_mutex); > + ret = tsl2591_get_power_state(chip); > + mutex_unlock(&chip->als_mutex); > + if (ret < 0) > + return ret; > + > + return !!(ret & TSL2591_ENABLE_ALS_INT); > +} > + > +static int tsl2591_write_event_config(struct iio_dev *indio_dev, > + const struct iio_chan_spec *chan, > + enum iio_event_type type, > + enum iio_event_direction dir, > + int state) > +{ > + struct tsl2591_chip *chip = iio_priv(indio_dev); > + struct i2c_client *client = chip->client; > + > + if (state && !chip->events_enabled) { > + chip->events_enabled = true; > + pm_runtime_get_sync(&client->dev); > + } else if (!state && chip->events_enabled) { > + chip->events_enabled = false; > + pm_runtime_mark_last_busy(&client->dev); > + pm_runtime_put_autosuspend(&client->dev); > + } > + > + return 0; > +} > + > +static const struct iio_info tsl2591_info = { > + .attrs = &tsl2591_sysfs_attribute_group, > + .event_attrs = &tsl2591_event_attribute_group, > + .read_raw = tsl2591_read_raw, > + .read_event_value = tsl2591_read_event_value, > + .write_event_value = tsl2591_write_event_value, > + .read_event_config = tsl2591_read_event_config, > + .write_event_config = tsl2591_write_event_config, > +}; > + > +static int __maybe_unused tsl2591_suspend(struct device *dev) > +{ > + struct iio_dev *indio_dev = dev_get_drvdata(dev); > + struct tsl2591_chip *chip = iio_priv(indio_dev); > + int ret; > + > + mutex_lock(&chip->als_mutex); > + ret = tsl2591_set_power_state(chip, TSL2591_PWR_OFF); > + mutex_unlock(&chip->als_mutex); > + > + return ret; > +} > + > +static int __maybe_unused tsl2591_resume(struct device *dev) > +{ > + struct iio_dev *indio_dev = dev_get_drvdata(dev); > + struct tsl2591_chip *chip = iio_priv(indio_dev); > + int ret; > + int power_state; > + > + if (chip->events_enabled) > + power_state = TSL2591_PWR_ON | TSL2591_ENABLE_ALS_INT | > + TSL2591_ENABLE_ALS; > + else > + power_state = TSL2591_PWR_ON | TSL2591_ENABLE_ALS; > + > + mutex_lock(&chip->als_mutex); > + ret = tsl2591_set_power_state(chip, power_state); > + mutex_unlock(&chip->als_mutex); > + > + return ret; > +} > + > +static const struct dev_pm_ops tsl2591_pm_ops = { > + SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend, > + pm_runtime_force_resume) > + SET_RUNTIME_PM_OPS(tsl2591_suspend, tsl2591_resume, NULL) > +}; > + > +static irqreturn_t tsl2591_event_handler(int irq, void *private) > +{ > + struct iio_dev *dev_info = private; > + struct tsl2591_chip *chip = iio_priv(dev_info); > + struct i2c_client *client = chip->client; > + int ret; > + > + if (!chip->events_enabled) > + return IRQ_HANDLED; > + > + iio_push_event(dev_info, > + IIO_UNMOD_EVENT_CODE(IIO_LIGHT, 0, > + IIO_EV_TYPE_THRESH, > + IIO_EV_DIR_EITHER), > + iio_get_time_ns(dev_info)); > + > + /* Clear als irq */ > + ret = i2c_smbus_write_byte(client, TSL2591_CMD_SF_CALS_NPI); > + if (ret < 0) > + dev_err(&client->dev, "failed to clear als irq\n"); > + > + return IRQ_HANDLED; > +} > + > +static int tsl2591_load_defaults(struct tsl2591_chip *chip) > +{ > + struct i2c_client *client = chip->client; > + > + chip->als_settings.als_int_time = TSL2591_DEFAULT_ALS_INT_TIME; > + chip->als_settings.als_gain = TSL2591_DEFAULT_ALS_GAIN; > + chip->als_settings.als_persist = TSL2591_DEFAULT_ALS_PERSIST; > + chip->als_settings.als_lower_threshold = > + TSL2591_DEFAULT_ALS_LOWER_THRESHOLD; > + chip->als_settings.als_upper_threshold = > + TSL2591_DEFAULT_ALS_UPPER_THRESHOLD; > + > + if (tsl2591_set_als_gain_int_time(chip)) { > + dev_err(&client->dev, "Failed to set als gain and int time\n"); > + return -EINVAL; > + } > + > + if (tsl2591_set_als_persist_cycle(chip)) { > + dev_err(&client->dev, "Failed to set als thresholds\n"); wrong message, should refer to persist_cycle? > + return -EINVAL; > + } > + > + if (tsl2591_set_als_thresholds(chip)) { > + dev_err(&client->dev, "Failed to set als thresholds\n"); > + return -EINVAL; > + } > + > + return 0; > +} > + > +static void tsl2591_chip_off(void *data) > +{ > + struct iio_dev *indio_dev = data; > + struct tsl2591_chip *chip = iio_priv(indio_dev); > + struct i2c_client *client = chip->client; > + > + pm_runtime_disable(&client->dev); > + pm_runtime_set_suspended(&client->dev); > + pm_runtime_put_noidle(&client->dev); > + > + tsl2591_set_power_state(chip, TSL2591_PWR_OFF); > +} > + > +static int tsl2591_probe(struct i2c_client *client) > +{ > + struct tsl2591_chip *chip; > + struct iio_dev *indio_dev; > + int ret; > + > + if (!i2c_check_functionality(client->adapter, > + I2C_FUNC_SMBUS_BYTE_DATA)) { > + dev_err(&client->dev, > + "I2C smbus byte data functionality is not supported\n"); > + return -EOPNOTSUPP; > + } > + > + indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*chip)); > + if (!indio_dev) > + return -ENOMEM; > + > + chip = iio_priv(indio_dev); > + chip->client = client; > + i2c_set_clientdata(client, indio_dev); > + > + if (client->irq) { > + ret = devm_request_threaded_irq(&client->dev, client->irq, > + NULL, tsl2591_event_handler, > + IRQF_TRIGGER_FALLING | IRQF_ONESHOT, > + "tsl2591_irq", indio_dev); > + if (ret) { > + dev_err(&client->dev, "irq request error %d\n", -ret); > + return -EINVAL; > + } > + } > + > + mutex_init(&chip->als_mutex); > + > + ret = i2c_smbus_read_byte_data(client, > + TSL2591_CMD_NOP | TSL2591_DEVICE_ID); > + if (ret < 0) { > + dev_err(&client->dev, > + "Failed to read the device ID register\n"); > + return ret; > + } > + > + if ((ret & TSL2591_DEVICE_ID_MASK) != TSL2591_DEVICE_ID_VAL) { > + dev_err(&client->dev, "Device ID: %#04x unknown\n", ret); > + return -EINVAL; > + } > + > + indio_dev->info = &tsl2591_info; > + indio_dev->channels = tsl2591_channels; > + indio_dev->num_channels = ARRAY_SIZE(tsl2591_channels); > + indio_dev->modes = INDIO_DIRECT_MODE; > + indio_dev->name = chip->client->name; > + chip->events_enabled = false; > + > + pm_runtime_enable(&client->dev); > + pm_runtime_set_autosuspend_delay(&client->dev, > + TSL2591_POWER_OFF_DELAY_MS); > + pm_runtime_use_autosuspend(&client->dev); > + > + if (tsl2591_load_defaults(chip)) { > + dev_err(&client->dev, "Failed to load sensor defaults\n"); > + return -EINVAL; > + } > + > + ret = i2c_smbus_write_byte(client, TSL2591_CMD_SF_CALS_NPI); > + if (ret < 0) { > + dev_err(&client->dev, "failed to clear als irq\n"); maybe consistent first letter: Failed vs failed > + return -EINVAL; > + } > + > + /* Add chip off to automatically managed path */ > + ret = devm_add_action_or_reset(&client->dev, > + tsl2591_chip_off, > + indio_dev); > + if (ret < 0) > + return -EINVAL; > + > + ret = devm_iio_device_register(&client->dev, indio_dev); > + if (ret) { > + dev_err(&client->dev, "iio registration failed\n"); probably not a very informative message > + return ret; > + } > + > + dev_info(&client->dev, "Probe complete - tsl2591 found.\n"); message needed? > + > + return 0; > +} > + > +static const struct of_device_id tsl2591_of_match[] = { > + { .compatible = "amstaos,tsl2591"}, > + {}, > +}; > +MODULE_DEVICE_TABLE(of, tsl2591_of_match); > + > +static struct i2c_driver tsl2591_driver = { > + .driver = { > + .name = "tsl2591", > + .pm = &tsl2591_pm_ops, > + .of_match_table = tsl2591_of_match, > + }, > + .probe_new = tsl2591_probe, > +}; > +module_i2c_driver(tsl2591_driver); > + > +MODULE_AUTHOR("Joe Sandom <joe.sandom@outlook.com>"); > +MODULE_DESCRIPTION("TAOS tsl2591 ambient light sensor driver"); > +MODULE_LICENSE("GPL"); > -- Peter Meerwald-Stadler Mobile: +43 664 24 44 418 ^ permalink raw reply [flat|nested] 3+ messages in thread
[parent not found: <DB8P195MB0728DA940A9CC57EA2D05F00888B9@DB8P195MB0728.EURP195.PROD.OUTLOOK.COM>]
* Re: [PATCH v2] Added AMS tsl2591 driver implementation [not found] ` <DB8P195MB0728DA940A9CC57EA2D05F00888B9@DB8P195MB0728.EURP195.PROD.OUTLOOK.COM> @ 2021-02-12 19:22 ` Jonathan Cameron 2021-02-12 19:22 ` Jonathan Cameron 0 siblings, 1 reply; 3+ messages in thread From: Jonathan Cameron @ 2021-02-12 19:22 UTC (permalink / raw) To: Joe Sandom Cc: Peter Meerwald-Stadler, Lars-Peter Clausen, linux-iio, linux-kernel On Fri, 12 Feb 2021 12:56:02 +0000 Joe Sandom <joe.sandom@outlook.com> wrote: > Hi Peter, > > Thank you for your constructive feedback. I really appreciate you taking the time to review ?. Hi Joe, You sent an html reply, so it probably didn't reach anyone via the list. Well all do it from time to time so don't worry about it :) Thanks Jonathan > > I'll be posting a v3 shortly. > > Thanks, > > Joe > ________________________________ > From: Peter Meerwald-Stadler <pmeerw@pmeerw.net> > Sent: 10 February 2021 14:50 > To: Joe Sandom <joe.sandom@outlook.com> > Cc: jic23@kernel.org <jic23@kernel.org>; Lars-Peter Clausen <lars@metafoo.de>; linux-iio@vger.kernel.org <linux-iio@vger.kernel.org>; linux-kernel@vger.kernel.org <linux-kernel@vger.kernel.org> > Subject: Re: [PATCH v2] Added AMS tsl2591 driver implementation > > > > Driver implementation for AMS/TAOS tsl2591 ambient light sensor. > > please see comments below > > > > This driver supports configuration via device tree and sysfs. > > Supported channels for raw infrared light, raw visible light, > > raw combined light and combined lux value. > > The driver additionally supports iio events on lower and > > upper thresholds. > > > > This is a very-high sensitivity light-to-digital converter that > > transforms light intensity into a digital signal. > > > > Datasheet Available at: https://ams.com/tsl25911 > > > > Signed-off-by: Joe Sandom <joe.sandom@outlook.com> > > --- > > Changes in v2: > > - Significant modifications to ensure compatibility with standard userspace ABI > > - Removed unneccesary device tree properties where configuration can be > > handled either through sysfs or event properties > > - Improved readability of code by inlining where appropriate and > > modified naming in areas for clarity > > - Cleaned up Makefile and Kconfig to follow correct ordering > > - Removed noisy print outs and unnecessary use of __func__ > > - All chip configuration done in probe before exposing interfaces to > > userspace to avoid race conditions > > - Removed having events directly from probe, now follows appropriate > > event enable path > > - Removed channel showing visible light only as no real use case for it. > > Channels are now IR (raw), Visible + IR (raw) and Lux. > > - Cleaned up binding file to reflect removal of device tree properties > > > > NOTE: > > Apologies that v2 took a while to get submitted, making the changes to > > ensure compatibility with the standard userspace ABI took a lot longer > > than anticipated! mostly with the conversion of persist cycles to time > > in seconds with respect to ADC integration time amongst other things. > > > > .../bindings/iio/light/amstaos,tsl2591.yaml | 50 + > > drivers/iio/light/Kconfig | 11 + > > drivers/iio/light/Makefile | 1 + > > drivers/iio/light/tsl2591.c | 1247 +++++++++++++++++ > > 4 files changed, 1309 insertions(+) > > create mode 100644 Documentation/devicetree/bindings/iio/light/amstaos,tsl2591.yaml > > create mode 100644 drivers/iio/light/tsl2591.c > > > > diff --git a/Documentation/devicetree/bindings/iio/light/amstaos,tsl2591.yaml b/Documentation/devicetree/bindings/iio/light/amstaos,tsl2591.yaml > > new file mode 100644 > > index 000000000000..030d0bbfdc7b > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/iio/light/amstaos,tsl2591.yaml > > @@ -0,0 +1,50 @@ > > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) > > +%YAML 1.2 > > +--- > > +$id: http://devicetree.org/schemas/iio/light/tsl2591.yaml# > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > + > > +title: AMS/TAOS TSL2591 Ambient Light Sensor (ALS) > > + > > +maintainers: > > + - Joe Sandom <joe.sandom@outlook.com> > > + > > +description: | > > + AMS/TAOS TSL2591 is a very-high sensitivity > > + light-to-digital converter that transforms light intensity into a digital > > + signal. > > + > > +properties: > > + compatible: > > + const: amstaos,tsl2591 > > + > > + reg: > > + maxItems: 1 > > + > > + interrupts: > > + maxItems: 1 > > + description: > > + Interrupt (INT:Pin 2) Active low. Should be set to IRQ_TYPE_EDGE_FALLING. > > + interrupt is used to detect if lux value has reached below or above defined > > Interrupt > is it lux always? or just intensity in some cases > > > + threshold values. > > + > > +required: > > + - compatible > > + - reg > > + > > +additionalProperties: false > > + > > +examples: > > + - | > > + #include <dt-bindings/interrupt-controller/irq.h> > > + i2c { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + tsl2591@29 { > > + compatible = "amstaos,tsl2591"; > > + reg = <0x29>; > > + interrupts = <20 IRQ_TYPE_EDGE_FALLING>; > > + }; > > + }; > > +... > > diff --git a/drivers/iio/light/Kconfig b/drivers/iio/light/Kconfig > > index 33ad4dd0b5c7..0b0950a94925 100644 > > --- a/drivers/iio/light/Kconfig > > +++ b/drivers/iio/light/Kconfig > > @@ -501,6 +501,17 @@ config TSL2583 > > Provides support for the TAOS tsl2580, tsl2581 and tsl2583 devices. > > Access ALS data via iio, sysfs. > > > > +config TSL2591 > > + tristate "TAOS TSL2591 ambient light sensor" > > + depends on I2C > > + help > > + Select Y here for support of the AMS/TAOS TSL2591 ambient light sensor, > > + featuring visible and infrared lux output. Access als data via > > I think lux is defined for visible light only? > als -> ALS > > > + iio and sysfs. Supports iio_events. > > + > > + To compile this driver as a module, select M: the > > + module will be called tsl2591. > > + > > config TSL2772 > > tristate "TAOS TSL/TMD2x71 and TSL/TMD2x72 Family of light and proximity sensors" > > depends on I2C > > diff --git a/drivers/iio/light/Makefile b/drivers/iio/light/Makefile > > index ea376deaca54..d10912faf964 100644 > > --- a/drivers/iio/light/Makefile > > +++ b/drivers/iio/light/Makefile > > @@ -48,6 +48,7 @@ obj-$(CONFIG_ST_UVIS25_SPI) += st_uvis25_spi.o > > obj-$(CONFIG_TCS3414) += tcs3414.o > > obj-$(CONFIG_TCS3472) += tcs3472.o > > obj-$(CONFIG_TSL2583) += tsl2583.o > > +obj-$(CONFIG_TSL2591) += tsl2591.o > > obj-$(CONFIG_TSL2772) += tsl2772.o > > obj-$(CONFIG_TSL4531) += tsl4531.o > > obj-$(CONFIG_US5182D) += us5182d.o > > diff --git a/drivers/iio/light/tsl2591.c b/drivers/iio/light/tsl2591.c > > new file mode 100644 > > index 000000000000..fb402ddabeaf > > --- /dev/null > > +++ b/drivers/iio/light/tsl2591.c > > @@ -0,0 +1,1247 @@ > > +// SPDX-License-Identifier: GPL-2.0-or-later > > +/* > > + * Copyright (C) 2020 Joe Sandom <joe.sandom@outlook.com> > > + * > > + * Datasheet Available at: https://ams.com/tsl25911 > > available > > > + * > > + * Device driver for the TAOS TSL2591. This is a very-high sensitivity > > + * light-to-digital converter that transforms light intensity into a digital > > + * signal. > > + */ > > + > > +#include <linux/debugfs.h> > > +#include <linux/delay.h> > > +#include <linux/i2c.h> > > +#include <linux/interrupt.h> > > +#include <linux/kernel.h> > > +#include <linux/module.h> > > +#include <linux/mutex.h> > > +#include <linux/pm_runtime.h> > > + > > +#include <linux/iio/events.h> > > +#include <linux/iio/iio.h> > > +#include <linux/iio/sysfs.h> > > + > > +#define als_time_secs_to_ms(x) (((x) + 1) * 100) > > +#define als_time_ms_to_secs(x) (((x) / 100) - 1) > > maybe UPPERCASE macros? > > > + > > +/* TSL2591 Register Set */ > > +#define TSL2591_ENABLE 0x00 > > +#define TSL2591_CONTROL 0x01 > > +#define TSL2591_AILTL 0x04 > > +#define TSL2591_AILTH 0x05 > > +#define TSL2591_AIHTL 0x06 > > +#define TSL2591_AIHTH 0x07 > > +#define TSL2591_NP_AILTL 0x08 > > +#define TSL2591_NP_AILTH 0x09 > > +#define TSL2591_NP_AIHTL 0x0A > > +#define TSL2591_NP_AIHTH 0x0B > > +#define TSL2591_PERSIST 0x0C > > +#define TSL2591_PACKAGE_ID 0x11 > > +#define TSL2591_DEVICE_ID 0x12 > > +#define TSL2591_STATUS 0x13 > > +#define TSL2591_C0_DATAL 0x14 > > +#define TSL2591_C0_DATAH 0x15 > > +#define TSL2591_C1_DATAL 0x16 > > +#define TSL2591_C1_DATAH 0x17 > > + > > +/* TSL2591 Command Register Masks */ > > doesn't look like masks, more like values :) > > > +#define TSL2591_CMD_NOP 0xA0 > > +#define TSL2591_CMD_SF_INTSET 0xE4 > > +#define TSL2591_CMD_SF_CALS_I 0xE5 > > +#define TSL2591_CMD_SF_CALS_NPI 0xE7 > > +#define TSL2591_CMD_SF_CNP_ALSI 0xEA > > + > > +/* TSL2591 Enable Register Masks */ > > +#define TSL2591_PWR_ON 0x01 > > could use BIT() > > > +#define TSL2591_PWR_OFF 0x00 > > +#define TSL2591_ENABLE_ALS 0x02 > > +#define TSL2591_ENABLE_ALS_INT 0x10 > > +#define TSL2591_ENABLE_SLEEP_INT 0x40 > > +#define TSL2591_ENABLE_NP_INT 0x80 > > + > > +/* TSL2591 Control Register Masks */ > > +#define TSL2591_CTRL_ALS_INTEGRATION_100MS 0x00 > > +#define TSL2591_CTRL_ALS_INTEGRATION_200MS 0x01 > > +#define TSL2591_CTRL_ALS_INTEGRATION_300MS 0x02 > > +#define TSL2591_CTRL_ALS_INTEGRATION_400MS 0x03 > > +#define TSL2591_CTRL_ALS_INTEGRATION_500MS 0x04 > > +#define TSL2591_CTRL_ALS_INTEGRATION_600MS 0x05 > > +#define TSL2591_CTRL_ALS_LOW_GAIN 0x00 > > +#define TSL2591_CTRL_ALS_MED_GAIN 0x10 > > +#define TSL2591_CTRL_ALS_HIGH_GAIN 0x20 > > +#define TSL2591_CTRL_ALS_MAX_GAIN 0x30 > > +#define TSL2591_CTRL_SYS_RESET 0x80 > > + > > +/* TSL2591 Persist Register Masks */ > > not very mask-y > > > +#define TSL2591_PRST_ALS_INT_CYCLE_0 0x00 > > +#define TSL2591_PRST_ALS_INT_CYCLE_ANY 0x01 > > +#define TSL2591_PRST_ALS_INT_CYCLE_2 0x02 > > +#define TSL2591_PRST_ALS_INT_CYCLE_3 0x03 > > +#define TSL2591_PRST_ALS_INT_CYCLE_5 0x04 > > +#define TSL2591_PRST_ALS_INT_CYCLE_10 0x05 > > +#define TSL2591_PRST_ALS_INT_CYCLE_15 0x06 > > +#define TSL2591_PRST_ALS_INT_CYCLE_20 0x07 > > +#define TSL2591_PRST_ALS_INT_CYCLE_25 0x08 > > +#define TSL2591_PRST_ALS_INT_CYCLE_30 0x09 > > +#define TSL2591_PRST_ALS_INT_CYCLE_35 0x0A > > +#define TSL2591_PRST_ALS_INT_CYCLE_40 0x0B > > +#define TSL2591_PRST_ALS_INT_CYCLE_45 0x0C > > +#define TSL2591_PRST_ALS_INT_CYCLE_50 0x0D > > +#define TSL2591_PRST_ALS_INT_CYCLE_55 0x0E > > +#define TSL2591_PRST_ALS_INT_CYCLE_60 0x0F > > +#define TSL2591_PRST_ALS_INT_CYCLE_MAX TSL2591_PRST_ALS_INT_CYCLE_60 > > + > > +/* TSL2591 Persist Interrupt Cycle Literals */ > > +#define TSL2591_PRST_ALS_INT_CYCLE_1_LIT 1 > > +#define TSL2591_PRST_ALS_INT_CYCLE_2_LIT 2 > > +#define TSL2591_PRST_ALS_INT_CYCLE_3_LIT 3 > > +#define TSL2591_PRST_ALS_INT_CYCLE_5_LIT 5 > > +#define TSL2591_PRST_ALS_INT_CYCLE_10_LIT 10 > > +#define TSL2591_PRST_ALS_INT_CYCLE_15_LIT 15 > > +#define TSL2591_PRST_ALS_INT_CYCLE_20_LIT 20 > > +#define TSL2591_PRST_ALS_INT_CYCLE_25_LIT 25 > > +#define TSL2591_PRST_ALS_INT_CYCLE_30_LIT 30 > > +#define TSL2591_PRST_ALS_INT_CYCLE_35_LIT 35 > > +#define TSL2591_PRST_ALS_INT_CYCLE_40_LIT 40 > > +#define TSL2591_PRST_ALS_INT_CYCLE_45_LIT 45 > > +#define TSL2591_PRST_ALS_INT_CYCLE_50_LIT 50 > > +#define TSL2591_PRST_ALS_INT_CYCLE_55_LIT 55 > > +#define TSL2591_PRST_ALS_INT_CYCLE_60_LIT 60 > > + > > +/* TSL2591 PID Register Mask */ > > +#define TSL2591_PACKAGE_ID_MASK 0x30 > > + > > +/* TSL2591 ID Register Mask */ > > +#define TSL2591_DEVICE_ID_MASK 0xFF > > + > > +/* TSL2591 Status Register Masks */ > > +#define TSL2591_STS_ALS_VALID 0x01 > > +#define TSL2591_STS_ALS_INT 0x10 > > +#define TSL2591_STS_NPERS_INT 0x20 > > +#define TSL2591_STS_VAL_HIGH 0x01 > > + > > +/* TSL2591 Constant Values */ > > +#define TSL2591_PACKAGE_ID_VAL 0x00 > > +#define TSL2591_DEVICE_ID_VAL 0x50 > > + > > +/* Power off suspend delay time MS */ > > +#define TSL2591_POWER_OFF_DELAY_MS 2000 > > + > > +/* TSL2591 Default Values */ > > there are not just default values > > > +#define TSL2591_DEFAULT_ALS_INT_TIME TSL2591_CTRL_ALS_INTEGRATION_300MS > > +#define TSL2591_MAX_ALS_INT_TIME_MS 600 > > +#define TSL2591_DEFAULT_ALS_GAIN TSL2591_CTRL_ALS_MED_GAIN > > +#define TSL2591_NUM_DATA_CHANNELS 4 > > +#define TSL2591_DEFAULT_ALS_PERSIST TSL2591_PRST_ALS_INT_CYCLE_ANY > > +#define TSL2591_DEFAULT_ALS_LOWER_THRESHOLD 100 > > +#define TSL2591_DEFAULT_ALS_UPPER_THRESHOLD 1500 > > + > > +#define TSL2591_ALS_MAX_VALUE 65535 > > +#define TSL2591_ALS_STS_VALID_COUNT 10 > > + > > +/* LUX Calculations */ > > +/* AGAIN values from Adafruits TSL2591 Arduino library */ > > +/* https://github.com/adafruit/Adafruit_TSL2591_Library */ > > +#define TSL2591_CTRL_ALS_LOW_GAIN_MULTIPLIER 1 > > +#define TSL2591_CTRL_ALS_MED_GAIN_MULTIPLIER 25 > > +#define TSL2591_CTRL_ALS_HIGH_GAIN_MULTIPLIER 428 > > +#define TSL2591_CTRL_ALS_MAX_GAIN_MULTIPLIER 9876 > > +#define TSL2591_LUX_COEFFICIENT 408 > > + > > +static const u8 tsl2591_data_channels[] = { > > + TSL2591_C0_DATAL, > > + TSL2591_C0_DATAH, > > + TSL2591_C1_DATAL, > > + TSL2591_C1_DATAH, > > +}; > > + > > +struct tsl2591_als_readings { > > + u16 als_ch0; > > + u16 als_ch1; > > + u16 als_lux_int; > > + u16 als_lux_decimal; > > +}; > > + > > +struct tsl2591_settings { > > _als_settings for consistency? > everything seems to relate to ALS anyway > > > + u8 als_int_time; > > + u8 als_gain; > > + u8 als_persist; > > + u16 als_lower_threshold; > > + u16 als_upper_threshold; > > +}; > > + > > +struct tsl2591_chip { > > + /* Ambient light sensor mutex */ > > who would have guessed :) maybe drop comment > > > + struct mutex als_mutex; > > + struct i2c_client *client; > > + struct tsl2591_settings als_settings; > > + struct tsl2591_als_readings als_readings; > > + > > + bool events_enabled; > > +}; > > + > > +/* Period table is als persist cycle x integration time setting */ > > ALS > multi-line comment? > > > +/* Integration times: 100ms, 200ms, 300ms, 400ms, 500ms, 600ms */ > > +/* ALS cycles: 1, 2, 3, 5, 10, 20, 25, 30, 35, 40, 45, 50, 55, 60 */ > > +static const char * const tsl2591_als_period_list[] = { > > + "0.1 0.2 0.3 0.5 1.0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 ", > > remove space at the end? > > > + "0.2 0.4 0.6 1.0 2.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0", > > + "0.3 0.6 0.9 1.5 3.0 6.0 7.5 9.0 10.5 12.0 13.5 15.0 16.5 18.0", > > + "0.4 0.8 1.2 2.0 4.0 8.0 10.0 12.0 14.0 16.0 18.0 20.0 22.0 24.0 ", > > remove space at the end? > > > + "0.5 1.0 1.5 2.5 5.0 10.0 12.5 15.0 17.5 20.0 22.5 25.0 27.5 30.0", > > + "0.6 1.2 1.8 3.0 6.0 12.0 15.0 18.0 21.0 24.0 27.0 30.0 33.0 36.0", > > +}; > > + > > +static int tsl2591_gain_to_multiplier(const u8 als_gain) > > const necessary? just a bit unusual... > > > +{ > > + switch (als_gain) { > > + case TSL2591_CTRL_ALS_LOW_GAIN: > > + return TSL2591_CTRL_ALS_LOW_GAIN_MULTIPLIER; > > + case TSL2591_CTRL_ALS_MED_GAIN: > > + return TSL2591_CTRL_ALS_MED_GAIN_MULTIPLIER; > > + case TSL2591_CTRL_ALS_HIGH_GAIN: > > + return TSL2591_CTRL_ALS_HIGH_GAIN_MULTIPLIER; > > + case TSL2591_CTRL_ALS_MAX_GAIN: > > + return TSL2591_CTRL_ALS_MAX_GAIN_MULTIPLIER; > > + default: > > + break; > > maybe have the return -EINVAL right here and save some lines? > (here and elsewhere) > > > + } > > + > > + return -EINVAL; > > +} > > + > > +static u8 tsl2591_multiplier_to_gain(const u32 multiplier) > > +{ > > + switch (multiplier) { > > + case TSL2591_CTRL_ALS_LOW_GAIN_MULTIPLIER: > > + return TSL2591_CTRL_ALS_LOW_GAIN; > > + case TSL2591_CTRL_ALS_MED_GAIN_MULTIPLIER: > > + return TSL2591_CTRL_ALS_MED_GAIN; > > + case TSL2591_CTRL_ALS_HIGH_GAIN_MULTIPLIER: > > + return TSL2591_CTRL_ALS_HIGH_GAIN; > > + case TSL2591_CTRL_ALS_MAX_GAIN_MULTIPLIER: > > + return TSL2591_CTRL_ALS_MAX_GAIN; > > + default: > > + break; > > + } > > + > > + return -EINVAL; > > +} > > + > > +static int tsl2591_persist_cycle_to_lit(const u8 als_persist) > > +{ > > + switch (als_persist) { > > + case TSL2591_PRST_ALS_INT_CYCLE_ANY: > > + return TSL2591_PRST_ALS_INT_CYCLE_1_LIT; > > + case TSL2591_PRST_ALS_INT_CYCLE_2: > > + return TSL2591_PRST_ALS_INT_CYCLE_2_LIT; > > + case TSL2591_PRST_ALS_INT_CYCLE_3: > > + return TSL2591_PRST_ALS_INT_CYCLE_3_LIT; > > + case TSL2591_PRST_ALS_INT_CYCLE_5: > > + return TSL2591_PRST_ALS_INT_CYCLE_5_LIT; > > + case TSL2591_PRST_ALS_INT_CYCLE_10: > > + return TSL2591_PRST_ALS_INT_CYCLE_10_LIT; > > + case TSL2591_PRST_ALS_INT_CYCLE_15: > > + return TSL2591_PRST_ALS_INT_CYCLE_15_LIT; > > + case TSL2591_PRST_ALS_INT_CYCLE_20: > > + return TSL2591_PRST_ALS_INT_CYCLE_20_LIT; > > + case TSL2591_PRST_ALS_INT_CYCLE_25: > > + return TSL2591_PRST_ALS_INT_CYCLE_25_LIT; > > + case TSL2591_PRST_ALS_INT_CYCLE_30: > > + return TSL2591_PRST_ALS_INT_CYCLE_30_LIT; > > + case TSL2591_PRST_ALS_INT_CYCLE_35: > > + return TSL2591_PRST_ALS_INT_CYCLE_35_LIT; > > + case TSL2591_PRST_ALS_INT_CYCLE_40: > > + return TSL2591_PRST_ALS_INT_CYCLE_40_LIT; > > + case TSL2591_PRST_ALS_INT_CYCLE_45: > > + return TSL2591_PRST_ALS_INT_CYCLE_45_LIT; > > + case TSL2591_PRST_ALS_INT_CYCLE_50: > > + return TSL2591_PRST_ALS_INT_CYCLE_50_LIT; > > + case TSL2591_PRST_ALS_INT_CYCLE_55: > > + return TSL2591_PRST_ALS_INT_CYCLE_55_LIT; > > + case TSL2591_PRST_ALS_INT_CYCLE_60: > > + return TSL2591_PRST_ALS_INT_CYCLE_60_LIT; > > + default: > > + break; > > + } > > + > > + return -EINVAL; > > +} > > + > > +static int tsl2591_persist_lit_to_cycle(const u8 als_persist) > > +{ > > + switch (als_persist) { > > + case TSL2591_PRST_ALS_INT_CYCLE_1_LIT: > > + return TSL2591_PRST_ALS_INT_CYCLE_ANY; > > + case TSL2591_PRST_ALS_INT_CYCLE_2_LIT: > > + return TSL2591_PRST_ALS_INT_CYCLE_2; > > + case TSL2591_PRST_ALS_INT_CYCLE_3_LIT: > > + return TSL2591_PRST_ALS_INT_CYCLE_3; > > + case TSL2591_PRST_ALS_INT_CYCLE_5_LIT: > > + return TSL2591_PRST_ALS_INT_CYCLE_5; > > + case TSL2591_PRST_ALS_INT_CYCLE_10_LIT: > > + return TSL2591_PRST_ALS_INT_CYCLE_10; > > + case TSL2591_PRST_ALS_INT_CYCLE_15_LIT: > > + return TSL2591_PRST_ALS_INT_CYCLE_15; > > + case TSL2591_PRST_ALS_INT_CYCLE_20_LIT: > > + return TSL2591_PRST_ALS_INT_CYCLE_20; > > + case TSL2591_PRST_ALS_INT_CYCLE_25_LIT: > > + return TSL2591_PRST_ALS_INT_CYCLE_25; > > + case TSL2591_PRST_ALS_INT_CYCLE_30_LIT: > > + return TSL2591_PRST_ALS_INT_CYCLE_30; > > + case TSL2591_PRST_ALS_INT_CYCLE_35_LIT: > > + return TSL2591_PRST_ALS_INT_CYCLE_35; > > + case TSL2591_PRST_ALS_INT_CYCLE_40_LIT: > > + return TSL2591_PRST_ALS_INT_CYCLE_40; > > + case TSL2591_PRST_ALS_INT_CYCLE_45_LIT: > > + return TSL2591_PRST_ALS_INT_CYCLE_45; > > + case TSL2591_PRST_ALS_INT_CYCLE_50_LIT: > > + return TSL2591_PRST_ALS_INT_CYCLE_50; > > + case TSL2591_PRST_ALS_INT_CYCLE_55_LIT: > > + return TSL2591_PRST_ALS_INT_CYCLE_55; > > + case TSL2591_PRST_ALS_INT_CYCLE_60_LIT: > > + return TSL2591_PRST_ALS_INT_CYCLE_60; > > + default: > > + break; > > + } > > + > > + return -EINVAL; > > +} > > + > > +static int tsl2591_compatible_int_time(struct tsl2591_chip *chip, > > + u32 als_integration_time) > > const u32 for consistency? here and elsewhere > > > +{ > > + switch (als_integration_time) { > > + case TSL2591_CTRL_ALS_INTEGRATION_100MS: > > + case TSL2591_CTRL_ALS_INTEGRATION_200MS: > > + case TSL2591_CTRL_ALS_INTEGRATION_300MS: > > + case TSL2591_CTRL_ALS_INTEGRATION_400MS: > > + case TSL2591_CTRL_ALS_INTEGRATION_500MS: > > + case TSL2591_CTRL_ALS_INTEGRATION_600MS: > > + chip->als_settings.als_int_time = als_integration_time; > > + return 0; > > + default: > > + break; > > + } > > + > > + return -EINVAL; > > +} > > + > > +static int tsl2591_compatible_gain(struct tsl2591_chip *chip, u8 als_gain) > > +{ > > + switch (als_gain) { > > + case TSL2591_CTRL_ALS_LOW_GAIN: > > + case TSL2591_CTRL_ALS_MED_GAIN: > > + case TSL2591_CTRL_ALS_HIGH_GAIN: > > + case TSL2591_CTRL_ALS_MAX_GAIN: > > + chip->als_settings.als_gain = als_gain; > > + return 0; > > + default: > > + break; > > + } > > + > > + return -EINVAL; > > +} > > + > > +static int tsl2591_compatible_als_persist(struct tsl2591_chip *chip, > > + u32 als_persist) > > +{ > > + switch (als_persist) { > > + case TSL2591_PRST_ALS_INT_CYCLE_ANY: > > + case TSL2591_PRST_ALS_INT_CYCLE_2: > > + case TSL2591_PRST_ALS_INT_CYCLE_3: > > + case TSL2591_PRST_ALS_INT_CYCLE_5: > > + case TSL2591_PRST_ALS_INT_CYCLE_10: > > + case TSL2591_PRST_ALS_INT_CYCLE_15: > > + case TSL2591_PRST_ALS_INT_CYCLE_20: > > + case TSL2591_PRST_ALS_INT_CYCLE_25: > > + case TSL2591_PRST_ALS_INT_CYCLE_30: > > + case TSL2591_PRST_ALS_INT_CYCLE_35: > > + case TSL2591_PRST_ALS_INT_CYCLE_40: > > + case TSL2591_PRST_ALS_INT_CYCLE_45: > > + case TSL2591_PRST_ALS_INT_CYCLE_50: > > + case TSL2591_PRST_ALS_INT_CYCLE_55: > > + case TSL2591_PRST_ALS_INT_CYCLE_60: > > + chip->als_settings.als_persist = als_persist; > > + return 0; > > + default: > > + break; > > + } > > + > > + return -EINVAL; > > +} > > + > > +static int tsl2591_wait_adc_complete(struct tsl2591_chip *chip) > > +{ > > + struct i2c_client *client = chip->client; > > + struct tsl2591_settings settings = chip->als_settings; > > + int delay = als_time_secs_to_ms(settings.als_int_time); > > + int ret; > > + int i; > > + > > + if (!delay) > > + return -EINVAL; > > + > > + /* > > + * Sleep for als integration time to allow enough time > > ALS (here and elsewhere) > > > + * for an ADC read cycle to complete. Check status after > > + * delay for als valid > > + */ > > + msleep(delay); > > + > > + /* Check for status als valid flag for up to 100ms */ > > + for (i = 0; i < TSL2591_ALS_STS_VALID_COUNT; ++i) { > > + ret = i2c_smbus_read_byte_data(client, TSL2591_CMD_NOP | > > + TSL2591_STATUS); > > + if (ret < 0) { > > + dev_err(&client->dev, "failed to read register\n"); > > + return -EINVAL; > > + } > > + > > + if ((ret & TSL2591_STS_ALS_VALID) == TSL2591_STS_VAL_HIGH) > > + break; > > + > > + if (i == (TSL2591_ALS_STS_VALID_COUNT - 1)) > > + return -ENODATA; > > + > > + usleep_range(9000, 10000); > > + } > > + > > + return 0; > > +} > > + > > +/** > > + * tsl2591_read_channel_data() - Reads raw channel data and calculates lux > > + * > > + * Formula for lux calculation; > > + * Derived from Adafruit's TSL2591 library > > + * Link: https://github.com/adafruit/Adafruit_TSL2591_Library > > + * Counts Per Lux (CPL) = (ATIME_ms * AGAIN) / LUX DF > > + * lux = ((C0DATA - C1DATA) * (1 - (C1DATA / C0DATA))) / CPL > > + * > > + * Scale values to get more representative value of lux i.e. > > + * lux = ((C0DATA - C1DATA) * (1000 - ((C1DATA * 1000) / C0DATA))) / CPL > > + * > > + * Channel 0 = IR + Visible > > + * Channel 1 = IR only > > + * Visible = Channel 0 - Channel 1 > > + * > > + */ > > +static int tsl2591_read_channel_data(struct iio_dev *indio_dev) > > +{ > > + struct tsl2591_chip *chip = iio_priv(indio_dev); > > + struct tsl2591_settings *settings = &chip->als_settings; > > + struct i2c_client *client = chip->client; > > + int i; > > + int ret; > > + u8 channel_data[TSL2591_NUM_DATA_CHANNELS]; > > + > > + int counts_per_lux; > > + int lux; > > + int gain_multiplier; > > + > > + ret = tsl2591_wait_adc_complete(chip); > > + if (ret < 0) { > > + dev_err(&client->dev, "No data available. Err: %d\n", ret); > > + return -ENODATA; > > return ret; _wait_adc_complete() may also return -EINVAL > > > + } > > + > > + for (i = 0; i < TSL2591_NUM_DATA_CHANNELS; ++i) { > > + int reg = TSL2591_CMD_NOP | tsl2591_data_channels[i]; > > + > > + ret = i2c_smbus_read_byte_data(client, TSL2591_CMD_NOP | reg); > > + if (ret < 0) { > > + dev_err(&client->dev, > > + "Failed to read register %#04x\n", reg); > > + return -EINVAL; > > + } > > + channel_data[i] = ret; > > + } > > + > > + chip->als_readings.als_ch0 = > > + le16_to_cpup((const __le16 *)&channel_data[0]); > > + chip->als_readings.als_ch1 = > > + le16_to_cpup((const __le16 *)&channel_data[2]); > > + > > + dev_dbg(&client->dev, "both: %d\n", chip->als_readings.als_ch0); > > + dev_dbg(&client->dev, "ir: %d\n", chip->als_readings.als_ch1); > > + > > + gain_multiplier = tsl2591_gain_to_multiplier(settings->als_gain); > > + if (gain_multiplier < 0) { > > + dev_err(&client->dev, "Invalid multiplier. Err: %d\n", > > + gain_multiplier); > > + return -EINVAL; > > + } > > + > > + /* Calculate counts per lux value */ > > + counts_per_lux = (als_time_secs_to_ms(settings->als_int_time) * > > + gain_multiplier) / TSL2591_LUX_COEFFICIENT; > > + > > + dev_dbg(&client->dev, "Counts Per Lux (CPL): %d\n", counts_per_lux); > > + > > + /* Calculate lux value */ > > + lux = ((chip->als_readings.als_ch0 - chip->als_readings.als_ch1) * > > + (1000 - ((chip->als_readings.als_ch1 * 1000) / > > + chip->als_readings.als_ch0))) / counts_per_lux; > > + > > + /* Divide by 1000 to get real lux value before scaling */ > > + chip->als_readings.als_lux_int = lux / 1000; > > + > > + /* Get the decimal part of lux reading */ > > + chip->als_readings.als_lux_decimal = > > + (lux - (chip->als_readings.als_lux_int * 1000)); > > + > > + dev_dbg(&client->dev, "Raw lux calculation: %d\n", lux); > > + > > + return ret; > > +} > > + > > +static int tsl2591_set_als_gain_int_time(struct tsl2591_chip *chip) > > +{ > > + struct i2c_client *client = chip->client; > > + struct tsl2591_settings als_settings = chip->als_settings; > > + int ret; > > + > > + ret = i2c_smbus_write_byte_data(client, > > + TSL2591_CMD_NOP | TSL2591_CONTROL, > > + als_settings.als_int_time | > > + als_settings.als_gain); > > + if (ret < 0) > > + dev_err(&client->dev, "Failed to set als gain & int time\n"); > > + > > + return ret; > > +} > > + > > +static int tsl2591_set_als_thresholds(struct tsl2591_chip *chip) > > +{ > > + struct i2c_client *client = chip->client; > > + struct tsl2591_settings als_settings = chip->als_settings; > > + int ret; > > + > > + u8 als_lower_l; > > + u8 als_lower_h; > > + u8 als_upper_l; > > + u8 als_upper_h; > > + > > + if (als_settings.als_lower_threshold >= als_settings.als_upper_threshold) { > > + dev_warn(&client->dev, "lower threshold higher than upper\n"); > > + return -EINVAL; > > + } > > + > > + if (als_settings.als_upper_threshold > TSL2591_ALS_MAX_VALUE) { > > + dev_warn(&client->dev, "upper threshold higher than max\n"); > > + return -EINVAL; > > + } > > + > > + als_lower_l = (als_settings.als_lower_threshold & 0x00FF); > > + als_lower_h = ((als_settings.als_lower_threshold >> 8) & 0x00FF); > > + als_upper_l = (als_settings.als_upper_threshold & 0x00FF); > > + als_upper_h = ((als_settings.als_upper_threshold >> 8) & 0x00FF); > > + > > + dev_dbg(&client->dev, "Setting configuration - als lower l: %#04x\n", > > + als_lower_l); > > + dev_dbg(&client->dev, "Setting configuration - als lower h: %#04x\n", > > + als_lower_h); > > + dev_dbg(&client->dev, "Setting configuration - als upper l: %#04x\n", > > + als_upper_l); > > + dev_dbg(&client->dev, "Setting configuration - als upper h: %#04x\n", > > + als_upper_h); > > + > > + ret = i2c_smbus_write_byte_data(client, TSL2591_CMD_NOP | > > + TSL2591_AILTL, als_lower_l); > > + if (ret < 0) > > + dev_err(&client->dev, "Failed to set als lower threshold\n"); > > + > > + ret = i2c_smbus_write_byte_data(client, TSL2591_CMD_NOP | > > + TSL2591_AILTH, als_lower_h); > > + if (ret < 0) > > + dev_err(&client->dev, "Failed to set als lower threshold\n"); > > + > > + ret = i2c_smbus_write_byte_data(client, TSL2591_CMD_NOP | > > + TSL2591_AIHTL, als_upper_l); > > + if (ret < 0) > > + dev_err(&client->dev, "Failed to set als upper threshold\n"); > > + > > + ret = i2c_smbus_write_byte_data(client, TSL2591_CMD_NOP | > > + TSL2591_AIHTH, als_upper_h); > > + if (ret < 0) > > + dev_err(&client->dev, "Failed to set als upper threshold\n"); > > + > > + return ret; > > +} > > + > > +static int tsl2591_set_als_persist_cycle(struct tsl2591_chip *chip) > > +{ > > + struct i2c_client *client = chip->client; > > + struct tsl2591_settings als_settings = chip->als_settings; > > + int ret; > > + > > + ret = i2c_smbus_write_byte_data(client, TSL2591_CMD_NOP | > > + TSL2591_PERSIST, als_settings.als_persist); > > + if (ret < 0) > > + dev_err(&client->dev, "Failed to set als persist cycle\n"); > > + > > + return ret; > > +} > > + > > +static int tsl2591_set_power_state(struct tsl2591_chip *chip, u8 state) > > +{ > > + struct i2c_client *client = chip->client; > > + int ret; > > + > > + ret = i2c_smbus_write_byte_data(client, TSL2591_CMD_NOP | > > + TSL2591_ENABLE, state); > > + if (ret < 0) > > + dev_err(&client->dev, > > + "Failed to set the power state to %#04x\n", state); > > + > > + return ret; > > +} > > + > > +static int tsl2591_get_power_state(struct tsl2591_chip *chip) > > +{ > > + struct i2c_client *client = chip->client; > > + int ret; > > + > > + ret = i2c_smbus_read_byte_data(client, TSL2591_CMD_NOP | > > + TSL2591_ENABLE); > > + if (ret < 0) > > + dev_err(&client->dev, "Failed to get power state\n"); > > + > > + return ret; > > +} > > + > > +static ssize_t in_illuminance_integration_time_show(struct device *dev, > > tsl2591_ prefix missing > > > + struct device_attribute *attr, > > + char *buf) > > +{ > > + struct iio_dev *indio_dev = dev_to_iio_dev(dev); > > + struct tsl2591_chip *chip = iio_priv(indio_dev); > > + int ret; > > + > > + int als_int_time = als_time_secs_to_ms(chip->als_settings.als_int_time); > > + > > + mutex_lock(&chip->als_mutex); > > what purpose does the mutex serve? > > > + ret = sprintf(buf, "%d\n", als_int_time); > > + mutex_unlock(&chip->als_mutex); > > + > > + return ret; > > +} > > + > > +static ssize_t in_illuminance_integration_time_store(struct device *dev, > > tsl2591_ prefix > > > + struct device_attribute *attr, > > + const char *buf, size_t len) > > +{ > > + struct iio_dev *indio_dev = dev_to_iio_dev(dev); > > + struct tsl2591_chip *chip = iio_priv(indio_dev); > > + struct i2c_client *client = chip->client; > > + > > + u32 int_time; > > + int value; > > + > > + if (kstrtoint(buf, 0, &value) || !value) > > + return -EINVAL; > > + > > + mutex_lock(&chip->als_mutex); > > + > > + int_time = als_time_ms_to_secs(value); > > + > > + if (tsl2591_compatible_int_time(chip, int_time)) > > + goto calibrate_error; > > + > > + if (tsl2591_set_als_gain_int_time(chip)) > > + goto calibrate_error; > > + > > + mutex_unlock(&chip->als_mutex); > > + > > + return len; > > + > > +calibrate_error: > > + dev_err(&client->dev, "Failed to calibrate sensor\n"); > > + mutex_unlock(&chip->als_mutex); > > + return -EINVAL; > > +} > > + > > +static ssize_t in_illuminance_calibscale_show(struct device *dev, > > + struct device_attribute *attr, > > + char *buf) > > +{ > > + struct iio_dev *indio_dev = dev_to_iio_dev(dev); > > + struct tsl2591_chip *chip = iio_priv(indio_dev); > > + int ret; > > + > > + mutex_lock(&chip->als_mutex); > > + ret = sprintf(buf, "%d\n", tsl2591_gain_to_multiplier > > + (chip->als_settings.als_gain)); > > + mutex_unlock(&chip->als_mutex); > > + > > + return ret; > > +} > > + > > +static ssize_t in_illuminance_calibscale_store(struct device *dev, > > + struct device_attribute *attr, > > + const char *buf, size_t len) > > +{ > > + struct iio_dev *indio_dev = dev_to_iio_dev(dev); > > + struct tsl2591_chip *chip = iio_priv(indio_dev); > > + struct i2c_client *client = chip->client; > > + > > + u8 gain; > > + int value; > > + > > + if (kstrtoint(buf, 0, &value) || !value) > > + return -EINVAL; > > + > > + mutex_lock(&chip->als_mutex); > > + > > + gain = tsl2591_multiplier_to_gain(value); > > + > > + if (tsl2591_compatible_gain(chip, gain)) > > + goto calibrate_error; > > + > > + if (tsl2591_set_als_gain_int_time(chip)) > > + goto calibrate_error; > > + > > + mutex_unlock(&chip->als_mutex); > > + > > + return len; > > + > > +calibrate_error: > > + dev_err(&client->dev, "Failed to calibrate sensor\n"); > > + mutex_unlock(&chip->als_mutex); > > + return -EINVAL; > > +} > > + > > +static ssize_t in_illuminance_period_available_show(struct device *dev, > > + struct device_attribute *attr, > > + char *buf) > > +{ > > + struct iio_dev *indio_dev = dev_to_iio_dev(dev); > > + struct tsl2591_chip *chip = iio_priv(indio_dev); > > + int ret; > > + > > + mutex_lock(&chip->als_mutex); > > + ret = snprintf(buf, PAGE_SIZE, "%s\n", > > + tsl2591_als_period_list[chip->als_settings.als_int_time]); > > + mutex_unlock(&chip->als_mutex); > > + > > + return ret; > > +} > > + > > +static IIO_CONST_ATTR(in_illuminance_integration_time_available, > > + "100 200 300 400 500 600"); > > +static IIO_CONST_ATTR(in_illuminance_calibscale_available, > > + "1 25 428 9876"); > > +static IIO_DEVICE_ATTR_RW(in_illuminance_integration_time, 0); > > +static IIO_DEVICE_ATTR_RW(in_illuminance_calibscale, 0); > > + > > +static struct attribute *tsl2591_sysfs_attrs_ctrl[] = { > > + &iio_const_attr_in_illuminance_integration_time_available.dev_attr.attr, > > + &iio_const_attr_in_illuminance_calibscale_available.dev_attr.attr, > > + &iio_dev_attr_in_illuminance_integration_time.dev_attr.attr, > > + &iio_dev_attr_in_illuminance_calibscale.dev_attr.attr, > > + NULL > > +}; > > + > > +static const struct attribute_group tsl2591_sysfs_attribute_group = { > > + .attrs = tsl2591_sysfs_attrs_ctrl, > > +}; > > + > > +static IIO_DEVICE_ATTR_RO(in_illuminance_period_available, 0); > > + > > +static struct attribute *tsl2591_event_attrs_ctrl[] = { > > + &iio_dev_attr_in_illuminance_period_available.dev_attr.attr, > > + NULL > > +}; > > + > > +static const struct attribute_group tsl2591_event_attribute_group = { > > + .attrs = tsl2591_event_attrs_ctrl, > > +}; > > + > > +static const struct iio_event_spec tsl2591_events[] = { > > + { > > + .type = IIO_EV_TYPE_THRESH, > > + .dir = IIO_EV_DIR_RISING, > > + .mask_separate = BIT(IIO_EV_INFO_VALUE), > > + }, { > > + .type = IIO_EV_TYPE_THRESH, > > + .dir = IIO_EV_DIR_FALLING, > > + .mask_separate = BIT(IIO_EV_INFO_VALUE), > > + }, { > > + .type = IIO_EV_TYPE_THRESH, > > + .dir = IIO_EV_DIR_EITHER, > > + .mask_separate = BIT(IIO_EV_INFO_PERIOD) | > > + BIT(IIO_EV_INFO_ENABLE), > > + }, > > +}; > > + > > +static const struct iio_chan_spec tsl2591_channels[] = { > > + { > > + .type = IIO_INTENSITY, > > + .modified = 1, > > + .channel2 = IIO_MOD_LIGHT_IR, > > + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), > > + }, > > + { > > + .type = IIO_INTENSITY, > > + .modified = 1, > > + .channel2 = IIO_MOD_LIGHT_BOTH, > > + .event_spec = tsl2591_events, > > + .num_event_specs = ARRAY_SIZE(tsl2591_events), > > + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), > > + }, > > + { > > + .type = IIO_LIGHT, > > + .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED), > > + }, > > +}; > > + > > +static int tsl2591_read_raw(struct iio_dev *indio_dev, > > + struct iio_chan_spec const *chan, > > + int *val, int *val2, long mask) > > +{ > > + struct tsl2591_chip *chip = iio_priv(indio_dev); > > + struct i2c_client *client = chip->client; > > + int ret; > > + > > + dev_dbg(&client->dev, "Reading from sensor"); > > + > > + pm_runtime_get_sync(&chip->client->dev); > > + > > + mutex_lock(&chip->als_mutex); > > + > > + ret = -EINVAL; > > + switch (mask) { > > + case IIO_CHAN_INFO_RAW: > > + if (chan->type == IIO_INTENSITY) { > > + ret = tsl2591_read_channel_data(indio_dev); > > + if (ret < 0) > > + break; > > + > > + if (chan->channel2 == IIO_MOD_LIGHT_BOTH) { > > + *val = chip->als_readings.als_ch0; > > + ret = IIO_VAL_INT; > > + } else if (chan->channel2 == IIO_MOD_LIGHT_IR) { > > + *val = chip->als_readings.als_ch1; > > + ret = IIO_VAL_INT; > > + } else { > > + ret = -EINVAL; > > + } > > + } > > + break; > > + case IIO_CHAN_INFO_PROCESSED: > > + if (chan->type == IIO_LIGHT) { > > + ret = tsl2591_read_channel_data(indio_dev); > > + if (ret < 0) > > + break; > > + *val = chip->als_readings.als_lux_int; > > + *val2 = (chip->als_readings.als_lux_decimal * 1000); > > + ret = IIO_VAL_INT_PLUS_MICRO; > > + } > > + break; > > + } > > + > > + mutex_unlock(&chip->als_mutex); > > + > > + pm_runtime_mark_last_busy(&chip->client->dev); > > + pm_runtime_put_autosuspend(&chip->client->dev); > > + > > + return ret; > > +} > > + > > +static int tsl2591_read_event_value(struct iio_dev *indio_dev, > > + const struct iio_chan_spec *chan, > > + enum iio_event_type type, > > + enum iio_event_direction dir, > > + enum iio_event_info info, int *val, > > + int *val2) > > +{ > > + struct tsl2591_chip *chip = iio_priv(indio_dev); > > + struct i2c_client *client = chip->client; > > + int als_persist; > > + int period; > > + int ret; > > + int int_time; > > + > > + switch (info) { > > + case IIO_EV_INFO_VALUE: > > + switch (dir) { > > + case IIO_EV_DIR_RISING: > > + mutex_lock(&chip->als_mutex); > > + *val = chip->als_settings.als_upper_threshold; > > + mutex_unlock(&chip->als_mutex); > > + break; > > + case IIO_EV_DIR_FALLING: > > + mutex_lock(&chip->als_mutex); > > + *val = chip->als_settings.als_lower_threshold; > > + mutex_unlock(&chip->als_mutex); > > + break; > > + default: > > + return -EINVAL; > > + } > > + ret = IIO_VAL_INT; > > + break; > > + case IIO_EV_INFO_PERIOD: > > + mutex_lock(&chip->als_mutex); > > + > > + ret = i2c_smbus_read_byte_data(client, > > + TSL2591_CMD_NOP | TSL2591_PERSIST); > > + if (ret <= 0 || ret > TSL2591_PRST_ALS_INT_CYCLE_MAX) > > + goto err; > > + > > + als_persist = tsl2591_persist_cycle_to_lit(ret); > > + int_time = als_time_secs_to_ms(chip->als_settings.als_int_time); > > + period = als_persist * (int_time * MSEC_PER_SEC); > > + > > + *val = period / USEC_PER_SEC; > > + *val2 = period % USEC_PER_SEC; > > + > > + mutex_unlock(&chip->als_mutex); > > + ret = IIO_VAL_INT_PLUS_MICRO; > > + break; > > + default: > > + return -EINVAL; > > + } > > + > > + return ret; > > + > > +err: > > + mutex_unlock(&chip->als_mutex); > > + return -EINVAL; > > +} > > + > > +static int tsl2591_write_event_value(struct iio_dev *indio_dev, > > + const struct iio_chan_spec *chan, > > + enum iio_event_type type, > > + enum iio_event_direction dir, > > + enum iio_event_info info, int val, > > + int val2) > > +{ > > + struct tsl2591_chip *chip = iio_priv(indio_dev); > > + int period, int_time, als_cycle; > > + > > + if (val < 0 || val2 < 0) > > + return -EINVAL; > > + > > + switch (info) { > > + case IIO_EV_INFO_VALUE: > > + if (val > TSL2591_ALS_MAX_VALUE) > > + return -EINVAL; > > + /* Lower threshold should not be higher than upper */ > > + if (dir == IIO_EV_DIR_FALLING) > > + if (val > chip->als_settings.als_upper_threshold) > > + return -EINVAL; > > + > > + switch (dir) { > > + case IIO_EV_DIR_RISING: > > + mutex_lock(&chip->als_mutex); > > + chip->als_settings.als_upper_threshold = val; > > + if (tsl2591_set_als_thresholds(chip)) > > + goto err; > > + mutex_unlock(&chip->als_mutex); > > + break; > > + case IIO_EV_DIR_FALLING: > > + mutex_lock(&chip->als_mutex); > > + chip->als_settings.als_lower_threshold = val; > > + if (tsl2591_set_als_thresholds(chip)) > > + goto err; > > + mutex_unlock(&chip->als_mutex); > > + break; > > + default: > > + return -EINVAL; > > + } > > + break; > > + case IIO_EV_INFO_PERIOD: > > + mutex_lock(&chip->als_mutex); > > + int_time = als_time_secs_to_ms(chip->als_settings.als_int_time); > > + if (!val && val2) > > + period = (val2 / MSEC_PER_SEC) / int_time; > > + else if (val && !val2) > > + period = (val * MSEC_PER_SEC) / int_time; > > + else if (val && val2) > > + period = ((val * MSEC_PER_SEC) + > > + (val2 / MSEC_PER_SEC)) / int_time; > > + else > > + goto err; > > + > > + als_cycle = tsl2591_persist_lit_to_cycle(period); > > + if (als_cycle < 0) > > + goto err; > > + if (tsl2591_compatible_als_persist(chip, als_cycle)) > > + goto err; > > + if (tsl2591_set_als_persist_cycle(chip)) > > + goto err; > > + mutex_unlock(&chip->als_mutex); > > + break; > > + default: > > + return -EINVAL; > > + } > > + > > + return 0; > > +err: > > + mutex_unlock(&chip->als_mutex); > > + return -EINVAL; > > +} > > + > > +static int tsl2591_read_event_config(struct iio_dev *indio_dev, > > + const struct iio_chan_spec *chan, > > + enum iio_event_type type, > > + enum iio_event_direction dir) > > +{ > > + struct tsl2591_chip *chip = iio_priv(indio_dev); > > + int ret; > > + > > + mutex_lock(&chip->als_mutex); > > + ret = tsl2591_get_power_state(chip); > > + mutex_unlock(&chip->als_mutex); > > + if (ret < 0) > > + return ret; > > + > > + return !!(ret & TSL2591_ENABLE_ALS_INT); > > +} > > + > > +static int tsl2591_write_event_config(struct iio_dev *indio_dev, > > + const struct iio_chan_spec *chan, > > + enum iio_event_type type, > > + enum iio_event_direction dir, > > + int state) > > +{ > > + struct tsl2591_chip *chip = iio_priv(indio_dev); > > + struct i2c_client *client = chip->client; > > + > > + if (state && !chip->events_enabled) { > > + chip->events_enabled = true; > > + pm_runtime_get_sync(&client->dev); > > + } else if (!state && chip->events_enabled) { > > + chip->events_enabled = false; > > + pm_runtime_mark_last_busy(&client->dev); > > + pm_runtime_put_autosuspend(&client->dev); > > + } > > + > > + return 0; > > +} > > + > > +static const struct iio_info tsl2591_info = { > > + .attrs = &tsl2591_sysfs_attribute_group, > > + .event_attrs = &tsl2591_event_attribute_group, > > + .read_raw = tsl2591_read_raw, > > + .read_event_value = tsl2591_read_event_value, > > + .write_event_value = tsl2591_write_event_value, > > + .read_event_config = tsl2591_read_event_config, > > + .write_event_config = tsl2591_write_event_config, > > +}; > > + > > +static int __maybe_unused tsl2591_suspend(struct device *dev) > > +{ > > + struct iio_dev *indio_dev = dev_get_drvdata(dev); > > + struct tsl2591_chip *chip = iio_priv(indio_dev); > > + int ret; > > + > > + mutex_lock(&chip->als_mutex); > > + ret = tsl2591_set_power_state(chip, TSL2591_PWR_OFF); > > + mutex_unlock(&chip->als_mutex); > > + > > + return ret; > > +} > > + > > +static int __maybe_unused tsl2591_resume(struct device *dev) > > +{ > > + struct iio_dev *indio_dev = dev_get_drvdata(dev); > > + struct tsl2591_chip *chip = iio_priv(indio_dev); > > + int ret; > > + int power_state; > > + > > + if (chip->events_enabled) > > + power_state = TSL2591_PWR_ON | TSL2591_ENABLE_ALS_INT | > > + TSL2591_ENABLE_ALS; > > + else > > + power_state = TSL2591_PWR_ON | TSL2591_ENABLE_ALS; > > + > > + mutex_lock(&chip->als_mutex); > > + ret = tsl2591_set_power_state(chip, power_state); > > + mutex_unlock(&chip->als_mutex); > > + > > + return ret; > > +} > > + > > +static const struct dev_pm_ops tsl2591_pm_ops = { > > + SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend, > > + pm_runtime_force_resume) > > + SET_RUNTIME_PM_OPS(tsl2591_suspend, tsl2591_resume, NULL) > > +}; > > + > > +static irqreturn_t tsl2591_event_handler(int irq, void *private) > > +{ > > + struct iio_dev *dev_info = private; > > + struct tsl2591_chip *chip = iio_priv(dev_info); > > + struct i2c_client *client = chip->client; > > + int ret; > > + > > + if (!chip->events_enabled) > > + return IRQ_HANDLED; > > + > > + iio_push_event(dev_info, > > + IIO_UNMOD_EVENT_CODE(IIO_LIGHT, 0, > > + IIO_EV_TYPE_THRESH, > > + IIO_EV_DIR_EITHER), > > + iio_get_time_ns(dev_info)); > > + > > + /* Clear als irq */ > > + ret = i2c_smbus_write_byte(client, TSL2591_CMD_SF_CALS_NPI); > > + if (ret < 0) > > + dev_err(&client->dev, "failed to clear als irq\n"); > > + > > + return IRQ_HANDLED; > > +} > > + > > +static int tsl2591_load_defaults(struct tsl2591_chip *chip) > > +{ > > + struct i2c_client *client = chip->client; > > + > > + chip->als_settings.als_int_time = TSL2591_DEFAULT_ALS_INT_TIME; > > + chip->als_settings.als_gain = TSL2591_DEFAULT_ALS_GAIN; > > + chip->als_settings.als_persist = TSL2591_DEFAULT_ALS_PERSIST; > > + chip->als_settings.als_lower_threshold = > > + TSL2591_DEFAULT_ALS_LOWER_THRESHOLD; > > + chip->als_settings.als_upper_threshold = > > + TSL2591_DEFAULT_ALS_UPPER_THRESHOLD; > > + > > + if (tsl2591_set_als_gain_int_time(chip)) { > > + dev_err(&client->dev, "Failed to set als gain and int time\n"); > > + return -EINVAL; > > + } > > + > > + if (tsl2591_set_als_persist_cycle(chip)) { > > + dev_err(&client->dev, "Failed to set als thresholds\n"); > > wrong message, should refer to persist_cycle? > > > + return -EINVAL; > > + } > > + > > + if (tsl2591_set_als_thresholds(chip)) { > > + dev_err(&client->dev, "Failed to set als thresholds\n"); > > + return -EINVAL; > > + } > > + > > + return 0; > > +} > > + > > +static void tsl2591_chip_off(void *data) > > +{ > > + struct iio_dev *indio_dev = data; > > + struct tsl2591_chip *chip = iio_priv(indio_dev); > > + struct i2c_client *client = chip->client; > > + > > + pm_runtime_disable(&client->dev); > > + pm_runtime_set_suspended(&client->dev); > > + pm_runtime_put_noidle(&client->dev); > > + > > + tsl2591_set_power_state(chip, TSL2591_PWR_OFF); > > +} > > + > > +static int tsl2591_probe(struct i2c_client *client) > > +{ > > + struct tsl2591_chip *chip; > > + struct iio_dev *indio_dev; > > + int ret; > > + > > + if (!i2c_check_functionality(client->adapter, > > + I2C_FUNC_SMBUS_BYTE_DATA)) { > > + dev_err(&client->dev, > > + "I2C smbus byte data functionality is not supported\n"); > > + return -EOPNOTSUPP; > > + } > > + > > + indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*chip)); > > + if (!indio_dev) > > + return -ENOMEM; > > + > > + chip = iio_priv(indio_dev); > > + chip->client = client; > > + i2c_set_clientdata(client, indio_dev); > > + > > + if (client->irq) { > > + ret = devm_request_threaded_irq(&client->dev, client->irq, > > + NULL, tsl2591_event_handler, > > + IRQF_TRIGGER_FALLING | IRQF_ONESHOT, > > + "tsl2591_irq", indio_dev); > > + if (ret) { > > + dev_err(&client->dev, "irq request error %d\n", -ret); > > + return -EINVAL; > > + } > > + } > > + > > + mutex_init(&chip->als_mutex); > > + > > + ret = i2c_smbus_read_byte_data(client, > > + TSL2591_CMD_NOP | TSL2591_DEVICE_ID); > > + if (ret < 0) { > > + dev_err(&client->dev, > > + "Failed to read the device ID register\n"); > > + return ret; > > + } > > + > > + if ((ret & TSL2591_DEVICE_ID_MASK) != TSL2591_DEVICE_ID_VAL) { > > + dev_err(&client->dev, "Device ID: %#04x unknown\n", ret); > > + return -EINVAL; > > + } > > + > > + indio_dev->info = &tsl2591_info; > > + indio_dev->channels = tsl2591_channels; > > + indio_dev->num_channels = ARRAY_SIZE(tsl2591_channels); > > + indio_dev->modes = INDIO_DIRECT_MODE; > > + indio_dev->name = chip->client->name; > > + chip->events_enabled = false; > > + > > + pm_runtime_enable(&client->dev); > > + pm_runtime_set_autosuspend_delay(&client->dev, > > + TSL2591_POWER_OFF_DELAY_MS); > > + pm_runtime_use_autosuspend(&client->dev); > > + > > + if (tsl2591_load_defaults(chip)) { > > + dev_err(&client->dev, "Failed to load sensor defaults\n"); > > + return -EINVAL; > > + } > > + > > + ret = i2c_smbus_write_byte(client, TSL2591_CMD_SF_CALS_NPI); > > + if (ret < 0) { > > + dev_err(&client->dev, "failed to clear als irq\n"); > > maybe consistent first letter: Failed vs failed > > > + return -EINVAL; > > + } > > + > > + /* Add chip off to automatically managed path */ > > + ret = devm_add_action_or_reset(&client->dev, > > + tsl2591_chip_off, > > + indio_dev); > > + if (ret < 0) > > + return -EINVAL; > > + > > + ret = devm_iio_device_register(&client->dev, indio_dev); > > + if (ret) { > > + dev_err(&client->dev, "iio registration failed\n"); > > probably not a very informative message > > > + return ret; > > + } > > + > > + dev_info(&client->dev, "Probe complete - tsl2591 found.\n"); > > message needed? > > > + > > + return 0; > > +} > > + > > +static const struct of_device_id tsl2591_of_match[] = { > > + { .compatible = "amstaos,tsl2591"}, > > + {}, > > +}; > > +MODULE_DEVICE_TABLE(of, tsl2591_of_match); > > + > > +static struct i2c_driver tsl2591_driver = { > > + .driver = { > > + .name = "tsl2591", > > + .pm = &tsl2591_pm_ops, > > + .of_match_table = tsl2591_of_match, > > + }, > > + .probe_new = tsl2591_probe, > > +}; > > +module_i2c_driver(tsl2591_driver); > > + > > +MODULE_AUTHOR("Joe Sandom <joe.sandom@outlook.com>"); > > +MODULE_DESCRIPTION("TAOS tsl2591 ambient light sensor driver"); > > +MODULE_LICENSE("GPL"); > > > > -- > > Peter Meerwald-Stadler > Mobile: +43 664 24 44 418 ^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [PATCH v2] Added AMS tsl2591 driver implementation 2021-02-12 19:22 ` Jonathan Cameron @ 2021-02-12 19:22 ` Jonathan Cameron 0 siblings, 0 replies; 3+ messages in thread From: Jonathan Cameron @ 2021-02-12 19:22 UTC (permalink / raw) To: Joe Sandom Cc: Peter Meerwald-Stadler, Lars-Peter Clausen, linux-iio, linux-kernel On Fri, 12 Feb 2021 12:56:02 +0000 Joe Sandom <joe.sandom@outlook.com> wrote: > Hi Peter, > > Thank you for your constructive feedback. I really appreciate you taking the time to review ?. Hi Joe, You sent an html reply, so it probably didn't reach anyone via the list. We all do it from time to time so don't worry about it :) Thanks Jonathan > > I'll be posting a v3 shortly. > > Thanks, > > Joe > ________________________________ > From: Peter Meerwald-Stadler <pmeerw@pmeerw.net> > Sent: 10 February 2021 14:50 > To: Joe Sandom <joe.sandom@outlook.com> > Cc: jic23@kernel.org <jic23@kernel.org>; Lars-Peter Clausen <lars@metafoo.de>; linux-iio@vger.kernel.org <linux-iio@vger.kernel.org>; linux-kernel@vger.kernel.org <linux-kernel@vger.kernel.org> > Subject: Re: [PATCH v2] Added AMS tsl2591 driver implementation > > > > Driver implementation for AMS/TAOS tsl2591 ambient light sensor. > > please see comments below > > > > This driver supports configuration via device tree and sysfs. > > Supported channels for raw infrared light, raw visible light, > > raw combined light and combined lux value. > > The driver additionally supports iio events on lower and > > upper thresholds. > > > > This is a very-high sensitivity light-to-digital converter that > > transforms light intensity into a digital signal. > > > > Datasheet Available at: https://ams.com/tsl25911 > > > > Signed-off-by: Joe Sandom <joe.sandom@outlook.com> > > --- > > Changes in v2: > > - Significant modifications to ensure compatibility with standard userspace ABI > > - Removed unneccesary device tree properties where configuration can be > > handled either through sysfs or event properties > > - Improved readability of code by inlining where appropriate and > > modified naming in areas for clarity > > - Cleaned up Makefile and Kconfig to follow correct ordering > > - Removed noisy print outs and unnecessary use of __func__ > > - All chip configuration done in probe before exposing interfaces to > > userspace to avoid race conditions > > - Removed having events directly from probe, now follows appropriate > > event enable path > > - Removed channel showing visible light only as no real use case for it. > > Channels are now IR (raw), Visible + IR (raw) and Lux. > > - Cleaned up binding file to reflect removal of device tree properties > > > > NOTE: > > Apologies that v2 took a while to get submitted, making the changes to > > ensure compatibility with the standard userspace ABI took a lot longer > > than anticipated! mostly with the conversion of persist cycles to time > > in seconds with respect to ADC integration time amongst other things. > > > > .../bindings/iio/light/amstaos,tsl2591.yaml | 50 + > > drivers/iio/light/Kconfig | 11 + > > drivers/iio/light/Makefile | 1 + > > drivers/iio/light/tsl2591.c | 1247 +++++++++++++++++ > > 4 files changed, 1309 insertions(+) > > create mode 100644 Documentation/devicetree/bindings/iio/light/amstaos,tsl2591.yaml > > create mode 100644 drivers/iio/light/tsl2591.c > > > > diff --git a/Documentation/devicetree/bindings/iio/light/amstaos,tsl2591.yaml b/Documentation/devicetree/bindings/iio/light/amstaos,tsl2591.yaml > > new file mode 100644 > > index 000000000000..030d0bbfdc7b > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/iio/light/amstaos,tsl2591.yaml > > @@ -0,0 +1,50 @@ > > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) > > +%YAML 1.2 > > +--- > > +$id: http://devicetree.org/schemas/iio/light/tsl2591.yaml# > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > + > > +title: AMS/TAOS TSL2591 Ambient Light Sensor (ALS) > > + > > +maintainers: > > + - Joe Sandom <joe.sandom@outlook.com> > > + > > +description: | > > + AMS/TAOS TSL2591 is a very-high sensitivity > > + light-to-digital converter that transforms light intensity into a digital > > + signal. > > + > > +properties: > > + compatible: > > + const: amstaos,tsl2591 > > + > > + reg: > > + maxItems: 1 > > + > > + interrupts: > > + maxItems: 1 > > + description: > > + Interrupt (INT:Pin 2) Active low. Should be set to IRQ_TYPE_EDGE_FALLING. > > + interrupt is used to detect if lux value has reached below or above defined > > Interrupt > is it lux always? or just intensity in some cases > > > + threshold values. > > + > > +required: > > + - compatible > > + - reg > > + > > +additionalProperties: false > > + > > +examples: > > + - | > > + #include <dt-bindings/interrupt-controller/irq.h> > > + i2c { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + tsl2591@29 { > > + compatible = "amstaos,tsl2591"; > > + reg = <0x29>; > > + interrupts = <20 IRQ_TYPE_EDGE_FALLING>; > > + }; > > + }; > > +... > > diff --git a/drivers/iio/light/Kconfig b/drivers/iio/light/Kconfig > > index 33ad4dd0b5c7..0b0950a94925 100644 > > --- a/drivers/iio/light/Kconfig > > +++ b/drivers/iio/light/Kconfig > > @@ -501,6 +501,17 @@ config TSL2583 > > Provides support for the TAOS tsl2580, tsl2581 and tsl2583 devices. > > Access ALS data via iio, sysfs. > > > > +config TSL2591 > > + tristate "TAOS TSL2591 ambient light sensor" > > + depends on I2C > > + help > > + Select Y here for support of the AMS/TAOS TSL2591 ambient light sensor, > > + featuring visible and infrared lux output. Access als data via > > I think lux is defined for visible light only? > als -> ALS > > > + iio and sysfs. Supports iio_events. > > + > > + To compile this driver as a module, select M: the > > + module will be called tsl2591. > > + > > config TSL2772 > > tristate "TAOS TSL/TMD2x71 and TSL/TMD2x72 Family of light and proximity sensors" > > depends on I2C > > diff --git a/drivers/iio/light/Makefile b/drivers/iio/light/Makefile > > index ea376deaca54..d10912faf964 100644 > > --- a/drivers/iio/light/Makefile > > +++ b/drivers/iio/light/Makefile > > @@ -48,6 +48,7 @@ obj-$(CONFIG_ST_UVIS25_SPI) += st_uvis25_spi.o > > obj-$(CONFIG_TCS3414) += tcs3414.o > > obj-$(CONFIG_TCS3472) += tcs3472.o > > obj-$(CONFIG_TSL2583) += tsl2583.o > > +obj-$(CONFIG_TSL2591) += tsl2591.o > > obj-$(CONFIG_TSL2772) += tsl2772.o > > obj-$(CONFIG_TSL4531) += tsl4531.o > > obj-$(CONFIG_US5182D) += us5182d.o > > diff --git a/drivers/iio/light/tsl2591.c b/drivers/iio/light/tsl2591.c > > new file mode 100644 > > index 000000000000..fb402ddabeaf > > --- /dev/null > > +++ b/drivers/iio/light/tsl2591.c > > @@ -0,0 +1,1247 @@ > > +// SPDX-License-Identifier: GPL-2.0-or-later > > +/* > > + * Copyright (C) 2020 Joe Sandom <joe.sandom@outlook.com> > > + * > > + * Datasheet Available at: https://ams.com/tsl25911 > > available > > > + * > > + * Device driver for the TAOS TSL2591. This is a very-high sensitivity > > + * light-to-digital converter that transforms light intensity into a digital > > + * signal. > > + */ > > + > > +#include <linux/debugfs.h> > > +#include <linux/delay.h> > > +#include <linux/i2c.h> > > +#include <linux/interrupt.h> > > +#include <linux/kernel.h> > > +#include <linux/module.h> > > +#include <linux/mutex.h> > > +#include <linux/pm_runtime.h> > > + > > +#include <linux/iio/events.h> > > +#include <linux/iio/iio.h> > > +#include <linux/iio/sysfs.h> > > + > > +#define als_time_secs_to_ms(x) (((x) + 1) * 100) > > +#define als_time_ms_to_secs(x) (((x) / 100) - 1) > > maybe UPPERCASE macros? > > > + > > +/* TSL2591 Register Set */ > > +#define TSL2591_ENABLE 0x00 > > +#define TSL2591_CONTROL 0x01 > > +#define TSL2591_AILTL 0x04 > > +#define TSL2591_AILTH 0x05 > > +#define TSL2591_AIHTL 0x06 > > +#define TSL2591_AIHTH 0x07 > > +#define TSL2591_NP_AILTL 0x08 > > +#define TSL2591_NP_AILTH 0x09 > > +#define TSL2591_NP_AIHTL 0x0A > > +#define TSL2591_NP_AIHTH 0x0B > > +#define TSL2591_PERSIST 0x0C > > +#define TSL2591_PACKAGE_ID 0x11 > > +#define TSL2591_DEVICE_ID 0x12 > > +#define TSL2591_STATUS 0x13 > > +#define TSL2591_C0_DATAL 0x14 > > +#define TSL2591_C0_DATAH 0x15 > > +#define TSL2591_C1_DATAL 0x16 > > +#define TSL2591_C1_DATAH 0x17 > > + > > +/* TSL2591 Command Register Masks */ > > doesn't look like masks, more like values :) > > > +#define TSL2591_CMD_NOP 0xA0 > > +#define TSL2591_CMD_SF_INTSET 0xE4 > > +#define TSL2591_CMD_SF_CALS_I 0xE5 > > +#define TSL2591_CMD_SF_CALS_NPI 0xE7 > > +#define TSL2591_CMD_SF_CNP_ALSI 0xEA > > + > > +/* TSL2591 Enable Register Masks */ > > +#define TSL2591_PWR_ON 0x01 > > could use BIT() > > > +#define TSL2591_PWR_OFF 0x00 > > +#define TSL2591_ENABLE_ALS 0x02 > > +#define TSL2591_ENABLE_ALS_INT 0x10 > > +#define TSL2591_ENABLE_SLEEP_INT 0x40 > > +#define TSL2591_ENABLE_NP_INT 0x80 > > + > > +/* TSL2591 Control Register Masks */ > > +#define TSL2591_CTRL_ALS_INTEGRATION_100MS 0x00 > > +#define TSL2591_CTRL_ALS_INTEGRATION_200MS 0x01 > > +#define TSL2591_CTRL_ALS_INTEGRATION_300MS 0x02 > > +#define TSL2591_CTRL_ALS_INTEGRATION_400MS 0x03 > > +#define TSL2591_CTRL_ALS_INTEGRATION_500MS 0x04 > > +#define TSL2591_CTRL_ALS_INTEGRATION_600MS 0x05 > > +#define TSL2591_CTRL_ALS_LOW_GAIN 0x00 > > +#define TSL2591_CTRL_ALS_MED_GAIN 0x10 > > +#define TSL2591_CTRL_ALS_HIGH_GAIN 0x20 > > +#define TSL2591_CTRL_ALS_MAX_GAIN 0x30 > > +#define TSL2591_CTRL_SYS_RESET 0x80 > > + > > +/* TSL2591 Persist Register Masks */ > > not very mask-y > > > +#define TSL2591_PRST_ALS_INT_CYCLE_0 0x00 > > +#define TSL2591_PRST_ALS_INT_CYCLE_ANY 0x01 > > +#define TSL2591_PRST_ALS_INT_CYCLE_2 0x02 > > +#define TSL2591_PRST_ALS_INT_CYCLE_3 0x03 > > +#define TSL2591_PRST_ALS_INT_CYCLE_5 0x04 > > +#define TSL2591_PRST_ALS_INT_CYCLE_10 0x05 > > +#define TSL2591_PRST_ALS_INT_CYCLE_15 0x06 > > +#define TSL2591_PRST_ALS_INT_CYCLE_20 0x07 > > +#define TSL2591_PRST_ALS_INT_CYCLE_25 0x08 > > +#define TSL2591_PRST_ALS_INT_CYCLE_30 0x09 > > +#define TSL2591_PRST_ALS_INT_CYCLE_35 0x0A > > +#define TSL2591_PRST_ALS_INT_CYCLE_40 0x0B > > +#define TSL2591_PRST_ALS_INT_CYCLE_45 0x0C > > +#define TSL2591_PRST_ALS_INT_CYCLE_50 0x0D > > +#define TSL2591_PRST_ALS_INT_CYCLE_55 0x0E > > +#define TSL2591_PRST_ALS_INT_CYCLE_60 0x0F > > +#define TSL2591_PRST_ALS_INT_CYCLE_MAX TSL2591_PRST_ALS_INT_CYCLE_60 > > + > > +/* TSL2591 Persist Interrupt Cycle Literals */ > > +#define TSL2591_PRST_ALS_INT_CYCLE_1_LIT 1 > > +#define TSL2591_PRST_ALS_INT_CYCLE_2_LIT 2 > > +#define TSL2591_PRST_ALS_INT_CYCLE_3_LIT 3 > > +#define TSL2591_PRST_ALS_INT_CYCLE_5_LIT 5 > > +#define TSL2591_PRST_ALS_INT_CYCLE_10_LIT 10 > > +#define TSL2591_PRST_ALS_INT_CYCLE_15_LIT 15 > > +#define TSL2591_PRST_ALS_INT_CYCLE_20_LIT 20 > > +#define TSL2591_PRST_ALS_INT_CYCLE_25_LIT 25 > > +#define TSL2591_PRST_ALS_INT_CYCLE_30_LIT 30 > > +#define TSL2591_PRST_ALS_INT_CYCLE_35_LIT 35 > > +#define TSL2591_PRST_ALS_INT_CYCLE_40_LIT 40 > > +#define TSL2591_PRST_ALS_INT_CYCLE_45_LIT 45 > > +#define TSL2591_PRST_ALS_INT_CYCLE_50_LIT 50 > > +#define TSL2591_PRST_ALS_INT_CYCLE_55_LIT 55 > > +#define TSL2591_PRST_ALS_INT_CYCLE_60_LIT 60 > > + > > +/* TSL2591 PID Register Mask */ > > +#define TSL2591_PACKAGE_ID_MASK 0x30 > > + > > +/* TSL2591 ID Register Mask */ > > +#define TSL2591_DEVICE_ID_MASK 0xFF > > + > > +/* TSL2591 Status Register Masks */ > > +#define TSL2591_STS_ALS_VALID 0x01 > > +#define TSL2591_STS_ALS_INT 0x10 > > +#define TSL2591_STS_NPERS_INT 0x20 > > +#define TSL2591_STS_VAL_HIGH 0x01 > > + > > +/* TSL2591 Constant Values */ > > +#define TSL2591_PACKAGE_ID_VAL 0x00 > > +#define TSL2591_DEVICE_ID_VAL 0x50 > > + > > +/* Power off suspend delay time MS */ > > +#define TSL2591_POWER_OFF_DELAY_MS 2000 > > + > > +/* TSL2591 Default Values */ > > there are not just default values > > > +#define TSL2591_DEFAULT_ALS_INT_TIME TSL2591_CTRL_ALS_INTEGRATION_300MS > > +#define TSL2591_MAX_ALS_INT_TIME_MS 600 > > +#define TSL2591_DEFAULT_ALS_GAIN TSL2591_CTRL_ALS_MED_GAIN > > +#define TSL2591_NUM_DATA_CHANNELS 4 > > +#define TSL2591_DEFAULT_ALS_PERSIST TSL2591_PRST_ALS_INT_CYCLE_ANY > > +#define TSL2591_DEFAULT_ALS_LOWER_THRESHOLD 100 > > +#define TSL2591_DEFAULT_ALS_UPPER_THRESHOLD 1500 > > + > > +#define TSL2591_ALS_MAX_VALUE 65535 > > +#define TSL2591_ALS_STS_VALID_COUNT 10 > > + > > +/* LUX Calculations */ > > +/* AGAIN values from Adafruits TSL2591 Arduino library */ > > +/* https://github.com/adafruit/Adafruit_TSL2591_Library */ > > +#define TSL2591_CTRL_ALS_LOW_GAIN_MULTIPLIER 1 > > +#define TSL2591_CTRL_ALS_MED_GAIN_MULTIPLIER 25 > > +#define TSL2591_CTRL_ALS_HIGH_GAIN_MULTIPLIER 428 > > +#define TSL2591_CTRL_ALS_MAX_GAIN_MULTIPLIER 9876 > > +#define TSL2591_LUX_COEFFICIENT 408 > > + > > +static const u8 tsl2591_data_channels[] = { > > + TSL2591_C0_DATAL, > > + TSL2591_C0_DATAH, > > + TSL2591_C1_DATAL, > > + TSL2591_C1_DATAH, > > +}; > > + > > +struct tsl2591_als_readings { > > + u16 als_ch0; > > + u16 als_ch1; > > + u16 als_lux_int; > > + u16 als_lux_decimal; > > +}; > > + > > +struct tsl2591_settings { > > _als_settings for consistency? > everything seems to relate to ALS anyway > > > + u8 als_int_time; > > + u8 als_gain; > > + u8 als_persist; > > + u16 als_lower_threshold; > > + u16 als_upper_threshold; > > +}; > > + > > +struct tsl2591_chip { > > + /* Ambient light sensor mutex */ > > who would have guessed :) maybe drop comment > > > + struct mutex als_mutex; > > + struct i2c_client *client; > > + struct tsl2591_settings als_settings; > > + struct tsl2591_als_readings als_readings; > > + > > + bool events_enabled; > > +}; > > + > > +/* Period table is als persist cycle x integration time setting */ > > ALS > multi-line comment? > > > +/* Integration times: 100ms, 200ms, 300ms, 400ms, 500ms, 600ms */ > > +/* ALS cycles: 1, 2, 3, 5, 10, 20, 25, 30, 35, 40, 45, 50, 55, 60 */ > > +static const char * const tsl2591_als_period_list[] = { > > + "0.1 0.2 0.3 0.5 1.0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 ", > > remove space at the end? > > > + "0.2 0.4 0.6 1.0 2.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0", > > + "0.3 0.6 0.9 1.5 3.0 6.0 7.5 9.0 10.5 12.0 13.5 15.0 16.5 18.0", > > + "0.4 0.8 1.2 2.0 4.0 8.0 10.0 12.0 14.0 16.0 18.0 20.0 22.0 24.0 ", > > remove space at the end? > > > + "0.5 1.0 1.5 2.5 5.0 10.0 12.5 15.0 17.5 20.0 22.5 25.0 27.5 30.0", > > + "0.6 1.2 1.8 3.0 6.0 12.0 15.0 18.0 21.0 24.0 27.0 30.0 33.0 36.0", > > +}; > > + > > +static int tsl2591_gain_to_multiplier(const u8 als_gain) > > const necessary? just a bit unusual... > > > +{ > > + switch (als_gain) { > > + case TSL2591_CTRL_ALS_LOW_GAIN: > > + return TSL2591_CTRL_ALS_LOW_GAIN_MULTIPLIER; > > + case TSL2591_CTRL_ALS_MED_GAIN: > > + return TSL2591_CTRL_ALS_MED_GAIN_MULTIPLIER; > > + case TSL2591_CTRL_ALS_HIGH_GAIN: > > + return TSL2591_CTRL_ALS_HIGH_GAIN_MULTIPLIER; > > + case TSL2591_CTRL_ALS_MAX_GAIN: > > + return TSL2591_CTRL_ALS_MAX_GAIN_MULTIPLIER; > > + default: > > + break; > > maybe have the return -EINVAL right here and save some lines? > (here and elsewhere) > > > + } > > + > > + return -EINVAL; > > +} > > + > > +static u8 tsl2591_multiplier_to_gain(const u32 multiplier) > > +{ > > + switch (multiplier) { > > + case TSL2591_CTRL_ALS_LOW_GAIN_MULTIPLIER: > > + return TSL2591_CTRL_ALS_LOW_GAIN; > > + case TSL2591_CTRL_ALS_MED_GAIN_MULTIPLIER: > > + return TSL2591_CTRL_ALS_MED_GAIN; > > + case TSL2591_CTRL_ALS_HIGH_GAIN_MULTIPLIER: > > + return TSL2591_CTRL_ALS_HIGH_GAIN; > > + case TSL2591_CTRL_ALS_MAX_GAIN_MULTIPLIER: > > + return TSL2591_CTRL_ALS_MAX_GAIN; > > + default: > > + break; > > + } > > + > > + return -EINVAL; > > +} > > + > > +static int tsl2591_persist_cycle_to_lit(const u8 als_persist) > > +{ > > + switch (als_persist) { > > + case TSL2591_PRST_ALS_INT_CYCLE_ANY: > > + return TSL2591_PRST_ALS_INT_CYCLE_1_LIT; > > + case TSL2591_PRST_ALS_INT_CYCLE_2: > > + return TSL2591_PRST_ALS_INT_CYCLE_2_LIT; > > + case TSL2591_PRST_ALS_INT_CYCLE_3: > > + return TSL2591_PRST_ALS_INT_CYCLE_3_LIT; > > + case TSL2591_PRST_ALS_INT_CYCLE_5: > > + return TSL2591_PRST_ALS_INT_CYCLE_5_LIT; > > + case TSL2591_PRST_ALS_INT_CYCLE_10: > > + return TSL2591_PRST_ALS_INT_CYCLE_10_LIT; > > + case TSL2591_PRST_ALS_INT_CYCLE_15: > > + return TSL2591_PRST_ALS_INT_CYCLE_15_LIT; > > + case TSL2591_PRST_ALS_INT_CYCLE_20: > > + return TSL2591_PRST_ALS_INT_CYCLE_20_LIT; > > + case TSL2591_PRST_ALS_INT_CYCLE_25: > > + return TSL2591_PRST_ALS_INT_CYCLE_25_LIT; > > + case TSL2591_PRST_ALS_INT_CYCLE_30: > > + return TSL2591_PRST_ALS_INT_CYCLE_30_LIT; > > + case TSL2591_PRST_ALS_INT_CYCLE_35: > > + return TSL2591_PRST_ALS_INT_CYCLE_35_LIT; > > + case TSL2591_PRST_ALS_INT_CYCLE_40: > > + return TSL2591_PRST_ALS_INT_CYCLE_40_LIT; > > + case TSL2591_PRST_ALS_INT_CYCLE_45: > > + return TSL2591_PRST_ALS_INT_CYCLE_45_LIT; > > + case TSL2591_PRST_ALS_INT_CYCLE_50: > > + return TSL2591_PRST_ALS_INT_CYCLE_50_LIT; > > + case TSL2591_PRST_ALS_INT_CYCLE_55: > > + return TSL2591_PRST_ALS_INT_CYCLE_55_LIT; > > + case TSL2591_PRST_ALS_INT_CYCLE_60: > > + return TSL2591_PRST_ALS_INT_CYCLE_60_LIT; > > + default: > > + break; > > + } > > + > > + return -EINVAL; > > +} > > + > > +static int tsl2591_persist_lit_to_cycle(const u8 als_persist) > > +{ > > + switch (als_persist) { > > + case TSL2591_PRST_ALS_INT_CYCLE_1_LIT: > > + return TSL2591_PRST_ALS_INT_CYCLE_ANY; > > + case TSL2591_PRST_ALS_INT_CYCLE_2_LIT: > > + return TSL2591_PRST_ALS_INT_CYCLE_2; > > + case TSL2591_PRST_ALS_INT_CYCLE_3_LIT: > > + return TSL2591_PRST_ALS_INT_CYCLE_3; > > + case TSL2591_PRST_ALS_INT_CYCLE_5_LIT: > > + return TSL2591_PRST_ALS_INT_CYCLE_5; > > + case TSL2591_PRST_ALS_INT_CYCLE_10_LIT: > > + return TSL2591_PRST_ALS_INT_CYCLE_10; > > + case TSL2591_PRST_ALS_INT_CYCLE_15_LIT: > > + return TSL2591_PRST_ALS_INT_CYCLE_15; > > + case TSL2591_PRST_ALS_INT_CYCLE_20_LIT: > > + return TSL2591_PRST_ALS_INT_CYCLE_20; > > + case TSL2591_PRST_ALS_INT_CYCLE_25_LIT: > > + return TSL2591_PRST_ALS_INT_CYCLE_25; > > + case TSL2591_PRST_ALS_INT_CYCLE_30_LIT: > > + return TSL2591_PRST_ALS_INT_CYCLE_30; > > + case TSL2591_PRST_ALS_INT_CYCLE_35_LIT: > > + return TSL2591_PRST_ALS_INT_CYCLE_35; > > + case TSL2591_PRST_ALS_INT_CYCLE_40_LIT: > > + return TSL2591_PRST_ALS_INT_CYCLE_40; > > + case TSL2591_PRST_ALS_INT_CYCLE_45_LIT: > > + return TSL2591_PRST_ALS_INT_CYCLE_45; > > + case TSL2591_PRST_ALS_INT_CYCLE_50_LIT: > > + return TSL2591_PRST_ALS_INT_CYCLE_50; > > + case TSL2591_PRST_ALS_INT_CYCLE_55_LIT: > > + return TSL2591_PRST_ALS_INT_CYCLE_55; > > + case TSL2591_PRST_ALS_INT_CYCLE_60_LIT: > > + return TSL2591_PRST_ALS_INT_CYCLE_60; > > + default: > > + break; > > + } > > + > > + return -EINVAL; > > +} > > + > > +static int tsl2591_compatible_int_time(struct tsl2591_chip *chip, > > + u32 als_integration_time) > > const u32 for consistency? here and elsewhere > > > +{ > > + switch (als_integration_time) { > > + case TSL2591_CTRL_ALS_INTEGRATION_100MS: > > + case TSL2591_CTRL_ALS_INTEGRATION_200MS: > > + case TSL2591_CTRL_ALS_INTEGRATION_300MS: > > + case TSL2591_CTRL_ALS_INTEGRATION_400MS: > > + case TSL2591_CTRL_ALS_INTEGRATION_500MS: > > + case TSL2591_CTRL_ALS_INTEGRATION_600MS: > > + chip->als_settings.als_int_time = als_integration_time; > > + return 0; > > + default: > > + break; > > + } > > + > > + return -EINVAL; > > +} > > + > > +static int tsl2591_compatible_gain(struct tsl2591_chip *chip, u8 als_gain) > > +{ > > + switch (als_gain) { > > + case TSL2591_CTRL_ALS_LOW_GAIN: > > + case TSL2591_CTRL_ALS_MED_GAIN: > > + case TSL2591_CTRL_ALS_HIGH_GAIN: > > + case TSL2591_CTRL_ALS_MAX_GAIN: > > + chip->als_settings.als_gain = als_gain; > > + return 0; > > + default: > > + break; > > + } > > + > > + return -EINVAL; > > +} > > + > > +static int tsl2591_compatible_als_persist(struct tsl2591_chip *chip, > > + u32 als_persist) > > +{ > > + switch (als_persist) { > > + case TSL2591_PRST_ALS_INT_CYCLE_ANY: > > + case TSL2591_PRST_ALS_INT_CYCLE_2: > > + case TSL2591_PRST_ALS_INT_CYCLE_3: > > + case TSL2591_PRST_ALS_INT_CYCLE_5: > > + case TSL2591_PRST_ALS_INT_CYCLE_10: > > + case TSL2591_PRST_ALS_INT_CYCLE_15: > > + case TSL2591_PRST_ALS_INT_CYCLE_20: > > + case TSL2591_PRST_ALS_INT_CYCLE_25: > > + case TSL2591_PRST_ALS_INT_CYCLE_30: > > + case TSL2591_PRST_ALS_INT_CYCLE_35: > > + case TSL2591_PRST_ALS_INT_CYCLE_40: > > + case TSL2591_PRST_ALS_INT_CYCLE_45: > > + case TSL2591_PRST_ALS_INT_CYCLE_50: > > + case TSL2591_PRST_ALS_INT_CYCLE_55: > > + case TSL2591_PRST_ALS_INT_CYCLE_60: > > + chip->als_settings.als_persist = als_persist; > > + return 0; > > + default: > > + break; > > + } > > + > > + return -EINVAL; > > +} > > + > > +static int tsl2591_wait_adc_complete(struct tsl2591_chip *chip) > > +{ > > + struct i2c_client *client = chip->client; > > + struct tsl2591_settings settings = chip->als_settings; > > + int delay = als_time_secs_to_ms(settings.als_int_time); > > + int ret; > > + int i; > > + > > + if (!delay) > > + return -EINVAL; > > + > > + /* > > + * Sleep for als integration time to allow enough time > > ALS (here and elsewhere) > > > + * for an ADC read cycle to complete. Check status after > > + * delay for als valid > > + */ > > + msleep(delay); > > + > > + /* Check for status als valid flag for up to 100ms */ > > + for (i = 0; i < TSL2591_ALS_STS_VALID_COUNT; ++i) { > > + ret = i2c_smbus_read_byte_data(client, TSL2591_CMD_NOP | > > + TSL2591_STATUS); > > + if (ret < 0) { > > + dev_err(&client->dev, "failed to read register\n"); > > + return -EINVAL; > > + } > > + > > + if ((ret & TSL2591_STS_ALS_VALID) == TSL2591_STS_VAL_HIGH) > > + break; > > + > > + if (i == (TSL2591_ALS_STS_VALID_COUNT - 1)) > > + return -ENODATA; > > + > > + usleep_range(9000, 10000); > > + } > > + > > + return 0; > > +} > > + > > +/** > > + * tsl2591_read_channel_data() - Reads raw channel data and calculates lux > > + * > > + * Formula for lux calculation; > > + * Derived from Adafruit's TSL2591 library > > + * Link: https://github.com/adafruit/Adafruit_TSL2591_Library > > + * Counts Per Lux (CPL) = (ATIME_ms * AGAIN) / LUX DF > > + * lux = ((C0DATA - C1DATA) * (1 - (C1DATA / C0DATA))) / CPL > > + * > > + * Scale values to get more representative value of lux i.e. > > + * lux = ((C0DATA - C1DATA) * (1000 - ((C1DATA * 1000) / C0DATA))) / CPL > > + * > > + * Channel 0 = IR + Visible > > + * Channel 1 = IR only > > + * Visible = Channel 0 - Channel 1 > > + * > > + */ > > +static int tsl2591_read_channel_data(struct iio_dev *indio_dev) > > +{ > > + struct tsl2591_chip *chip = iio_priv(indio_dev); > > + struct tsl2591_settings *settings = &chip->als_settings; > > + struct i2c_client *client = chip->client; > > + int i; > > + int ret; > > + u8 channel_data[TSL2591_NUM_DATA_CHANNELS]; > > + > > + int counts_per_lux; > > + int lux; > > + int gain_multiplier; > > + > > + ret = tsl2591_wait_adc_complete(chip); > > + if (ret < 0) { > > + dev_err(&client->dev, "No data available. Err: %d\n", ret); > > + return -ENODATA; > > return ret; _wait_adc_complete() may also return -EINVAL > > > + } > > + > > + for (i = 0; i < TSL2591_NUM_DATA_CHANNELS; ++i) { > > + int reg = TSL2591_CMD_NOP | tsl2591_data_channels[i]; > > + > > + ret = i2c_smbus_read_byte_data(client, TSL2591_CMD_NOP | reg); > > + if (ret < 0) { > > + dev_err(&client->dev, > > + "Failed to read register %#04x\n", reg); > > + return -EINVAL; > > + } > > + channel_data[i] = ret; > > + } > > + > > + chip->als_readings.als_ch0 = > > + le16_to_cpup((const __le16 *)&channel_data[0]); > > + chip->als_readings.als_ch1 = > > + le16_to_cpup((const __le16 *)&channel_data[2]); > > + > > + dev_dbg(&client->dev, "both: %d\n", chip->als_readings.als_ch0); > > + dev_dbg(&client->dev, "ir: %d\n", chip->als_readings.als_ch1); > > + > > + gain_multiplier = tsl2591_gain_to_multiplier(settings->als_gain); > > + if (gain_multiplier < 0) { > > + dev_err(&client->dev, "Invalid multiplier. Err: %d\n", > > + gain_multiplier); > > + return -EINVAL; > > + } > > + > > + /* Calculate counts per lux value */ > > + counts_per_lux = (als_time_secs_to_ms(settings->als_int_time) * > > + gain_multiplier) / TSL2591_LUX_COEFFICIENT; > > + > > + dev_dbg(&client->dev, "Counts Per Lux (CPL): %d\n", counts_per_lux); > > + > > + /* Calculate lux value */ > > + lux = ((chip->als_readings.als_ch0 - chip->als_readings.als_ch1) * > > + (1000 - ((chip->als_readings.als_ch1 * 1000) / > > + chip->als_readings.als_ch0))) / counts_per_lux; > > + > > + /* Divide by 1000 to get real lux value before scaling */ > > + chip->als_readings.als_lux_int = lux / 1000; > > + > > + /* Get the decimal part of lux reading */ > > + chip->als_readings.als_lux_decimal = > > + (lux - (chip->als_readings.als_lux_int * 1000)); > > + > > + dev_dbg(&client->dev, "Raw lux calculation: %d\n", lux); > > + > > + return ret; > > +} > > + > > +static int tsl2591_set_als_gain_int_time(struct tsl2591_chip *chip) > > +{ > > + struct i2c_client *client = chip->client; > > + struct tsl2591_settings als_settings = chip->als_settings; > > + int ret; > > + > > + ret = i2c_smbus_write_byte_data(client, > > + TSL2591_CMD_NOP | TSL2591_CONTROL, > > + als_settings.als_int_time | > > + als_settings.als_gain); > > + if (ret < 0) > > + dev_err(&client->dev, "Failed to set als gain & int time\n"); > > + > > + return ret; > > +} > > + > > +static int tsl2591_set_als_thresholds(struct tsl2591_chip *chip) > > +{ > > + struct i2c_client *client = chip->client; > > + struct tsl2591_settings als_settings = chip->als_settings; > > + int ret; > > + > > + u8 als_lower_l; > > + u8 als_lower_h; > > + u8 als_upper_l; > > + u8 als_upper_h; > > + > > + if (als_settings.als_lower_threshold >= als_settings.als_upper_threshold) { > > + dev_warn(&client->dev, "lower threshold higher than upper\n"); > > + return -EINVAL; > > + } > > + > > + if (als_settings.als_upper_threshold > TSL2591_ALS_MAX_VALUE) { > > + dev_warn(&client->dev, "upper threshold higher than max\n"); > > + return -EINVAL; > > + } > > + > > + als_lower_l = (als_settings.als_lower_threshold & 0x00FF); > > + als_lower_h = ((als_settings.als_lower_threshold >> 8) & 0x00FF); > > + als_upper_l = (als_settings.als_upper_threshold & 0x00FF); > > + als_upper_h = ((als_settings.als_upper_threshold >> 8) & 0x00FF); > > + > > + dev_dbg(&client->dev, "Setting configuration - als lower l: %#04x\n", > > + als_lower_l); > > + dev_dbg(&client->dev, "Setting configuration - als lower h: %#04x\n", > > + als_lower_h); > > + dev_dbg(&client->dev, "Setting configuration - als upper l: %#04x\n", > > + als_upper_l); > > + dev_dbg(&client->dev, "Setting configuration - als upper h: %#04x\n", > > + als_upper_h); > > + > > + ret = i2c_smbus_write_byte_data(client, TSL2591_CMD_NOP | > > + TSL2591_AILTL, als_lower_l); > > + if (ret < 0) > > + dev_err(&client->dev, "Failed to set als lower threshold\n"); > > + > > + ret = i2c_smbus_write_byte_data(client, TSL2591_CMD_NOP | > > + TSL2591_AILTH, als_lower_h); > > + if (ret < 0) > > + dev_err(&client->dev, "Failed to set als lower threshold\n"); > > + > > + ret = i2c_smbus_write_byte_data(client, TSL2591_CMD_NOP | > > + TSL2591_AIHTL, als_upper_l); > > + if (ret < 0) > > + dev_err(&client->dev, "Failed to set als upper threshold\n"); > > + > > + ret = i2c_smbus_write_byte_data(client, TSL2591_CMD_NOP | > > + TSL2591_AIHTH, als_upper_h); > > + if (ret < 0) > > + dev_err(&client->dev, "Failed to set als upper threshold\n"); > > + > > + return ret; > > +} > > + > > +static int tsl2591_set_als_persist_cycle(struct tsl2591_chip *chip) > > +{ > > + struct i2c_client *client = chip->client; > > + struct tsl2591_settings als_settings = chip->als_settings; > > + int ret; > > + > > + ret = i2c_smbus_write_byte_data(client, TSL2591_CMD_NOP | > > + TSL2591_PERSIST, als_settings.als_persist); > > + if (ret < 0) > > + dev_err(&client->dev, "Failed to set als persist cycle\n"); > > + > > + return ret; > > +} > > + > > +static int tsl2591_set_power_state(struct tsl2591_chip *chip, u8 state) > > +{ > > + struct i2c_client *client = chip->client; > > + int ret; > > + > > + ret = i2c_smbus_write_byte_data(client, TSL2591_CMD_NOP | > > + TSL2591_ENABLE, state); > > + if (ret < 0) > > + dev_err(&client->dev, > > + "Failed to set the power state to %#04x\n", state); > > + > > + return ret; > > +} > > + > > +static int tsl2591_get_power_state(struct tsl2591_chip *chip) > > +{ > > + struct i2c_client *client = chip->client; > > + int ret; > > + > > + ret = i2c_smbus_read_byte_data(client, TSL2591_CMD_NOP | > > + TSL2591_ENABLE); > > + if (ret < 0) > > + dev_err(&client->dev, "Failed to get power state\n"); > > + > > + return ret; > > +} > > + > > +static ssize_t in_illuminance_integration_time_show(struct device *dev, > > tsl2591_ prefix missing > > > + struct device_attribute *attr, > > + char *buf) > > +{ > > + struct iio_dev *indio_dev = dev_to_iio_dev(dev); > > + struct tsl2591_chip *chip = iio_priv(indio_dev); > > + int ret; > > + > > + int als_int_time = als_time_secs_to_ms(chip->als_settings.als_int_time); > > + > > + mutex_lock(&chip->als_mutex); > > what purpose does the mutex serve? > > > + ret = sprintf(buf, "%d\n", als_int_time); > > + mutex_unlock(&chip->als_mutex); > > + > > + return ret; > > +} > > + > > +static ssize_t in_illuminance_integration_time_store(struct device *dev, > > tsl2591_ prefix > > > + struct device_attribute *attr, > > + const char *buf, size_t len) > > +{ > > + struct iio_dev *indio_dev = dev_to_iio_dev(dev); > > + struct tsl2591_chip *chip = iio_priv(indio_dev); > > + struct i2c_client *client = chip->client; > > + > > + u32 int_time; > > + int value; > > + > > + if (kstrtoint(buf, 0, &value) || !value) > > + return -EINVAL; > > + > > + mutex_lock(&chip->als_mutex); > > + > > + int_time = als_time_ms_to_secs(value); > > + > > + if (tsl2591_compatible_int_time(chip, int_time)) > > + goto calibrate_error; > > + > > + if (tsl2591_set_als_gain_int_time(chip)) > > + goto calibrate_error; > > + > > + mutex_unlock(&chip->als_mutex); > > + > > + return len; > > + > > +calibrate_error: > > + dev_err(&client->dev, "Failed to calibrate sensor\n"); > > + mutex_unlock(&chip->als_mutex); > > + return -EINVAL; > > +} > > + > > +static ssize_t in_illuminance_calibscale_show(struct device *dev, > > + struct device_attribute *attr, > > + char *buf) > > +{ > > + struct iio_dev *indio_dev = dev_to_iio_dev(dev); > > + struct tsl2591_chip *chip = iio_priv(indio_dev); > > + int ret; > > + > > + mutex_lock(&chip->als_mutex); > > + ret = sprintf(buf, "%d\n", tsl2591_gain_to_multiplier > > + (chip->als_settings.als_gain)); > > + mutex_unlock(&chip->als_mutex); > > + > > + return ret; > > +} > > + > > +static ssize_t in_illuminance_calibscale_store(struct device *dev, > > + struct device_attribute *attr, > > + const char *buf, size_t len) > > +{ > > + struct iio_dev *indio_dev = dev_to_iio_dev(dev); > > + struct tsl2591_chip *chip = iio_priv(indio_dev); > > + struct i2c_client *client = chip->client; > > + > > + u8 gain; > > + int value; > > + > > + if (kstrtoint(buf, 0, &value) || !value) > > + return -EINVAL; > > + > > + mutex_lock(&chip->als_mutex); > > + > > + gain = tsl2591_multiplier_to_gain(value); > > + > > + if (tsl2591_compatible_gain(chip, gain)) > > + goto calibrate_error; > > + > > + if (tsl2591_set_als_gain_int_time(chip)) > > + goto calibrate_error; > > + > > + mutex_unlock(&chip->als_mutex); > > + > > + return len; > > + > > +calibrate_error: > > + dev_err(&client->dev, "Failed to calibrate sensor\n"); > > + mutex_unlock(&chip->als_mutex); > > + return -EINVAL; > > +} > > + > > +static ssize_t in_illuminance_period_available_show(struct device *dev, > > + struct device_attribute *attr, > > + char *buf) > > +{ > > + struct iio_dev *indio_dev = dev_to_iio_dev(dev); > > + struct tsl2591_chip *chip = iio_priv(indio_dev); > > + int ret; > > + > > + mutex_lock(&chip->als_mutex); > > + ret = snprintf(buf, PAGE_SIZE, "%s\n", > > + tsl2591_als_period_list[chip->als_settings.als_int_time]); > > + mutex_unlock(&chip->als_mutex); > > + > > + return ret; > > +} > > + > > +static IIO_CONST_ATTR(in_illuminance_integration_time_available, > > + "100 200 300 400 500 600"); > > +static IIO_CONST_ATTR(in_illuminance_calibscale_available, > > + "1 25 428 9876"); > > +static IIO_DEVICE_ATTR_RW(in_illuminance_integration_time, 0); > > +static IIO_DEVICE_ATTR_RW(in_illuminance_calibscale, 0); > > + > > +static struct attribute *tsl2591_sysfs_attrs_ctrl[] = { > > + &iio_const_attr_in_illuminance_integration_time_available.dev_attr.attr, > > + &iio_const_attr_in_illuminance_calibscale_available.dev_attr.attr, > > + &iio_dev_attr_in_illuminance_integration_time.dev_attr.attr, > > + &iio_dev_attr_in_illuminance_calibscale.dev_attr.attr, > > + NULL > > +}; > > + > > +static const struct attribute_group tsl2591_sysfs_attribute_group = { > > + .attrs = tsl2591_sysfs_attrs_ctrl, > > +}; > > + > > +static IIO_DEVICE_ATTR_RO(in_illuminance_period_available, 0); > > + > > +static struct attribute *tsl2591_event_attrs_ctrl[] = { > > + &iio_dev_attr_in_illuminance_period_available.dev_attr.attr, > > + NULL > > +}; > > + > > +static const struct attribute_group tsl2591_event_attribute_group = { > > + .attrs = tsl2591_event_attrs_ctrl, > > +}; > > + > > +static const struct iio_event_spec tsl2591_events[] = { > > + { > > + .type = IIO_EV_TYPE_THRESH, > > + .dir = IIO_EV_DIR_RISING, > > + .mask_separate = BIT(IIO_EV_INFO_VALUE), > > + }, { > > + .type = IIO_EV_TYPE_THRESH, > > + .dir = IIO_EV_DIR_FALLING, > > + .mask_separate = BIT(IIO_EV_INFO_VALUE), > > + }, { > > + .type = IIO_EV_TYPE_THRESH, > > + .dir = IIO_EV_DIR_EITHER, > > + .mask_separate = BIT(IIO_EV_INFO_PERIOD) | > > + BIT(IIO_EV_INFO_ENABLE), > > + }, > > +}; > > + > > +static const struct iio_chan_spec tsl2591_channels[] = { > > + { > > + .type = IIO_INTENSITY, > > + .modified = 1, > > + .channel2 = IIO_MOD_LIGHT_IR, > > + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), > > + }, > > + { > > + .type = IIO_INTENSITY, > > + .modified = 1, > > + .channel2 = IIO_MOD_LIGHT_BOTH, > > + .event_spec = tsl2591_events, > > + .num_event_specs = ARRAY_SIZE(tsl2591_events), > > + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), > > + }, > > + { > > + .type = IIO_LIGHT, > > + .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED), > > + }, > > +}; > > + > > +static int tsl2591_read_raw(struct iio_dev *indio_dev, > > + struct iio_chan_spec const *chan, > > + int *val, int *val2, long mask) > > +{ > > + struct tsl2591_chip *chip = iio_priv(indio_dev); > > + struct i2c_client *client = chip->client; > > + int ret; > > + > > + dev_dbg(&client->dev, "Reading from sensor"); > > + > > + pm_runtime_get_sync(&chip->client->dev); > > + > > + mutex_lock(&chip->als_mutex); > > + > > + ret = -EINVAL; > > + switch (mask) { > > + case IIO_CHAN_INFO_RAW: > > + if (chan->type == IIO_INTENSITY) { > > + ret = tsl2591_read_channel_data(indio_dev); > > + if (ret < 0) > > + break; > > + > > + if (chan->channel2 == IIO_MOD_LIGHT_BOTH) { > > + *val = chip->als_readings.als_ch0; > > + ret = IIO_VAL_INT; > > + } else if (chan->channel2 == IIO_MOD_LIGHT_IR) { > > + *val = chip->als_readings.als_ch1; > > + ret = IIO_VAL_INT; > > + } else { > > + ret = -EINVAL; > > + } > > + } > > + break; > > + case IIO_CHAN_INFO_PROCESSED: > > + if (chan->type == IIO_LIGHT) { > > + ret = tsl2591_read_channel_data(indio_dev); > > + if (ret < 0) > > + break; > > + *val = chip->als_readings.als_lux_int; > > + *val2 = (chip->als_readings.als_lux_decimal * 1000); > > + ret = IIO_VAL_INT_PLUS_MICRO; > > + } > > + break; > > + } > > + > > + mutex_unlock(&chip->als_mutex); > > + > > + pm_runtime_mark_last_busy(&chip->client->dev); > > + pm_runtime_put_autosuspend(&chip->client->dev); > > + > > + return ret; > > +} > > + > > +static int tsl2591_read_event_value(struct iio_dev *indio_dev, > > + const struct iio_chan_spec *chan, > > + enum iio_event_type type, > > + enum iio_event_direction dir, > > + enum iio_event_info info, int *val, > > + int *val2) > > +{ > > + struct tsl2591_chip *chip = iio_priv(indio_dev); > > + struct i2c_client *client = chip->client; > > + int als_persist; > > + int period; > > + int ret; > > + int int_time; > > + > > + switch (info) { > > + case IIO_EV_INFO_VALUE: > > + switch (dir) { > > + case IIO_EV_DIR_RISING: > > + mutex_lock(&chip->als_mutex); > > + *val = chip->als_settings.als_upper_threshold; > > + mutex_unlock(&chip->als_mutex); > > + break; > > + case IIO_EV_DIR_FALLING: > > + mutex_lock(&chip->als_mutex); > > + *val = chip->als_settings.als_lower_threshold; > > + mutex_unlock(&chip->als_mutex); > > + break; > > + default: > > + return -EINVAL; > > + } > > + ret = IIO_VAL_INT; > > + break; > > + case IIO_EV_INFO_PERIOD: > > + mutex_lock(&chip->als_mutex); > > + > > + ret = i2c_smbus_read_byte_data(client, > > + TSL2591_CMD_NOP | TSL2591_PERSIST); > > + if (ret <= 0 || ret > TSL2591_PRST_ALS_INT_CYCLE_MAX) > > + goto err; > > + > > + als_persist = tsl2591_persist_cycle_to_lit(ret); > > + int_time = als_time_secs_to_ms(chip->als_settings.als_int_time); > > + period = als_persist * (int_time * MSEC_PER_SEC); > > + > > + *val = period / USEC_PER_SEC; > > + *val2 = period % USEC_PER_SEC; > > + > > + mutex_unlock(&chip->als_mutex); > > + ret = IIO_VAL_INT_PLUS_MICRO; > > + break; > > + default: > > + return -EINVAL; > > + } > > + > > + return ret; > > + > > +err: > > + mutex_unlock(&chip->als_mutex); > > + return -EINVAL; > > +} > > + > > +static int tsl2591_write_event_value(struct iio_dev *indio_dev, > > + const struct iio_chan_spec *chan, > > + enum iio_event_type type, > > + enum iio_event_direction dir, > > + enum iio_event_info info, int val, > > + int val2) > > +{ > > + struct tsl2591_chip *chip = iio_priv(indio_dev); > > + int period, int_time, als_cycle; > > + > > + if (val < 0 || val2 < 0) > > + return -EINVAL; > > + > > + switch (info) { > > + case IIO_EV_INFO_VALUE: > > + if (val > TSL2591_ALS_MAX_VALUE) > > + return -EINVAL; > > + /* Lower threshold should not be higher than upper */ > > + if (dir == IIO_EV_DIR_FALLING) > > + if (val > chip->als_settings.als_upper_threshold) > > + return -EINVAL; > > + > > + switch (dir) { > > + case IIO_EV_DIR_RISING: > > + mutex_lock(&chip->als_mutex); > > + chip->als_settings.als_upper_threshold = val; > > + if (tsl2591_set_als_thresholds(chip)) > > + goto err; > > + mutex_unlock(&chip->als_mutex); > > + break; > > + case IIO_EV_DIR_FALLING: > > + mutex_lock(&chip->als_mutex); > > + chip->als_settings.als_lower_threshold = val; > > + if (tsl2591_set_als_thresholds(chip)) > > + goto err; > > + mutex_unlock(&chip->als_mutex); > > + break; > > + default: > > + return -EINVAL; > > + } > > + break; > > + case IIO_EV_INFO_PERIOD: > > + mutex_lock(&chip->als_mutex); > > + int_time = als_time_secs_to_ms(chip->als_settings.als_int_time); > > + if (!val && val2) > > + period = (val2 / MSEC_PER_SEC) / int_time; > > + else if (val && !val2) > > + period = (val * MSEC_PER_SEC) / int_time; > > + else if (val && val2) > > + period = ((val * MSEC_PER_SEC) + > > + (val2 / MSEC_PER_SEC)) / int_time; > > + else > > + goto err; > > + > > + als_cycle = tsl2591_persist_lit_to_cycle(period); > > + if (als_cycle < 0) > > + goto err; > > + if (tsl2591_compatible_als_persist(chip, als_cycle)) > > + goto err; > > + if (tsl2591_set_als_persist_cycle(chip)) > > + goto err; > > + mutex_unlock(&chip->als_mutex); > > + break; > > + default: > > + return -EINVAL; > > + } > > + > > + return 0; > > +err: > > + mutex_unlock(&chip->als_mutex); > > + return -EINVAL; > > +} > > + > > +static int tsl2591_read_event_config(struct iio_dev *indio_dev, > > + const struct iio_chan_spec *chan, > > + enum iio_event_type type, > > + enum iio_event_direction dir) > > +{ > > + struct tsl2591_chip *chip = iio_priv(indio_dev); > > + int ret; > > + > > + mutex_lock(&chip->als_mutex); > > + ret = tsl2591_get_power_state(chip); > > + mutex_unlock(&chip->als_mutex); > > + if (ret < 0) > > + return ret; > > + > > + return !!(ret & TSL2591_ENABLE_ALS_INT); > > +} > > + > > +static int tsl2591_write_event_config(struct iio_dev *indio_dev, > > + const struct iio_chan_spec *chan, > > + enum iio_event_type type, > > + enum iio_event_direction dir, > > + int state) > > +{ > > + struct tsl2591_chip *chip = iio_priv(indio_dev); > > + struct i2c_client *client = chip->client; > > + > > + if (state && !chip->events_enabled) { > > + chip->events_enabled = true; > > + pm_runtime_get_sync(&client->dev); > > + } else if (!state && chip->events_enabled) { > > + chip->events_enabled = false; > > + pm_runtime_mark_last_busy(&client->dev); > > + pm_runtime_put_autosuspend(&client->dev); > > + } > > + > > + return 0; > > +} > > + > > +static const struct iio_info tsl2591_info = { > > + .attrs = &tsl2591_sysfs_attribute_group, > > + .event_attrs = &tsl2591_event_attribute_group, > > + .read_raw = tsl2591_read_raw, > > + .read_event_value = tsl2591_read_event_value, > > + .write_event_value = tsl2591_write_event_value, > > + .read_event_config = tsl2591_read_event_config, > > + .write_event_config = tsl2591_write_event_config, > > +}; > > + > > +static int __maybe_unused tsl2591_suspend(struct device *dev) > > +{ > > + struct iio_dev *indio_dev = dev_get_drvdata(dev); > > + struct tsl2591_chip *chip = iio_priv(indio_dev); > > + int ret; > > + > > + mutex_lock(&chip->als_mutex); > > + ret = tsl2591_set_power_state(chip, TSL2591_PWR_OFF); > > + mutex_unlock(&chip->als_mutex); > > + > > + return ret; > > +} > > + > > +static int __maybe_unused tsl2591_resume(struct device *dev) > > +{ > > + struct iio_dev *indio_dev = dev_get_drvdata(dev); > > + struct tsl2591_chip *chip = iio_priv(indio_dev); > > + int ret; > > + int power_state; > > + > > + if (chip->events_enabled) > > + power_state = TSL2591_PWR_ON | TSL2591_ENABLE_ALS_INT | > > + TSL2591_ENABLE_ALS; > > + else > > + power_state = TSL2591_PWR_ON | TSL2591_ENABLE_ALS; > > + > > + mutex_lock(&chip->als_mutex); > > + ret = tsl2591_set_power_state(chip, power_state); > > + mutex_unlock(&chip->als_mutex); > > + > > + return ret; > > +} > > + > > +static const struct dev_pm_ops tsl2591_pm_ops = { > > + SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend, > > + pm_runtime_force_resume) > > + SET_RUNTIME_PM_OPS(tsl2591_suspend, tsl2591_resume, NULL) > > +}; > > + > > +static irqreturn_t tsl2591_event_handler(int irq, void *private) > > +{ > > + struct iio_dev *dev_info = private; > > + struct tsl2591_chip *chip = iio_priv(dev_info); > > + struct i2c_client *client = chip->client; > > + int ret; > > + > > + if (!chip->events_enabled) > > + return IRQ_HANDLED; > > + > > + iio_push_event(dev_info, > > + IIO_UNMOD_EVENT_CODE(IIO_LIGHT, 0, > > + IIO_EV_TYPE_THRESH, > > + IIO_EV_DIR_EITHER), > > + iio_get_time_ns(dev_info)); > > + > > + /* Clear als irq */ > > + ret = i2c_smbus_write_byte(client, TSL2591_CMD_SF_CALS_NPI); > > + if (ret < 0) > > + dev_err(&client->dev, "failed to clear als irq\n"); > > + > > + return IRQ_HANDLED; > > +} > > + > > +static int tsl2591_load_defaults(struct tsl2591_chip *chip) > > +{ > > + struct i2c_client *client = chip->client; > > + > > + chip->als_settings.als_int_time = TSL2591_DEFAULT_ALS_INT_TIME; > > + chip->als_settings.als_gain = TSL2591_DEFAULT_ALS_GAIN; > > + chip->als_settings.als_persist = TSL2591_DEFAULT_ALS_PERSIST; > > + chip->als_settings.als_lower_threshold = > > + TSL2591_DEFAULT_ALS_LOWER_THRESHOLD; > > + chip->als_settings.als_upper_threshold = > > + TSL2591_DEFAULT_ALS_UPPER_THRESHOLD; > > + > > + if (tsl2591_set_als_gain_int_time(chip)) { > > + dev_err(&client->dev, "Failed to set als gain and int time\n"); > > + return -EINVAL; > > + } > > + > > + if (tsl2591_set_als_persist_cycle(chip)) { > > + dev_err(&client->dev, "Failed to set als thresholds\n"); > > wrong message, should refer to persist_cycle? > > > + return -EINVAL; > > + } > > + > > + if (tsl2591_set_als_thresholds(chip)) { > > + dev_err(&client->dev, "Failed to set als thresholds\n"); > > + return -EINVAL; > > + } > > + > > + return 0; > > +} > > + > > +static void tsl2591_chip_off(void *data) > > +{ > > + struct iio_dev *indio_dev = data; > > + struct tsl2591_chip *chip = iio_priv(indio_dev); > > + struct i2c_client *client = chip->client; > > + > > + pm_runtime_disable(&client->dev); > > + pm_runtime_set_suspended(&client->dev); > > + pm_runtime_put_noidle(&client->dev); > > + > > + tsl2591_set_power_state(chip, TSL2591_PWR_OFF); > > +} > > + > > +static int tsl2591_probe(struct i2c_client *client) > > +{ > > + struct tsl2591_chip *chip; > > + struct iio_dev *indio_dev; > > + int ret; > > + > > + if (!i2c_check_functionality(client->adapter, > > + I2C_FUNC_SMBUS_BYTE_DATA)) { > > + dev_err(&client->dev, > > + "I2C smbus byte data functionality is not supported\n"); > > + return -EOPNOTSUPP; > > + } > > + > > + indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*chip)); > > + if (!indio_dev) > > + return -ENOMEM; > > + > > + chip = iio_priv(indio_dev); > > + chip->client = client; > > + i2c_set_clientdata(client, indio_dev); > > + > > + if (client->irq) { > > + ret = devm_request_threaded_irq(&client->dev, client->irq, > > + NULL, tsl2591_event_handler, > > + IRQF_TRIGGER_FALLING | IRQF_ONESHOT, > > + "tsl2591_irq", indio_dev); > > + if (ret) { > > + dev_err(&client->dev, "irq request error %d\n", -ret); > > + return -EINVAL; > > + } > > + } > > + > > + mutex_init(&chip->als_mutex); > > + > > + ret = i2c_smbus_read_byte_data(client, > > + TSL2591_CMD_NOP | TSL2591_DEVICE_ID); > > + if (ret < 0) { > > + dev_err(&client->dev, > > + "Failed to read the device ID register\n"); > > + return ret; > > + } > > + > > + if ((ret & TSL2591_DEVICE_ID_MASK) != TSL2591_DEVICE_ID_VAL) { > > + dev_err(&client->dev, "Device ID: %#04x unknown\n", ret); > > + return -EINVAL; > > + } > > + > > + indio_dev->info = &tsl2591_info; > > + indio_dev->channels = tsl2591_channels; > > + indio_dev->num_channels = ARRAY_SIZE(tsl2591_channels); > > + indio_dev->modes = INDIO_DIRECT_MODE; > > + indio_dev->name = chip->client->name; > > + chip->events_enabled = false; > > + > > + pm_runtime_enable(&client->dev); > > + pm_runtime_set_autosuspend_delay(&client->dev, > > + TSL2591_POWER_OFF_DELAY_MS); > > + pm_runtime_use_autosuspend(&client->dev); > > + > > + if (tsl2591_load_defaults(chip)) { > > + dev_err(&client->dev, "Failed to load sensor defaults\n"); > > + return -EINVAL; > > + } > > + > > + ret = i2c_smbus_write_byte(client, TSL2591_CMD_SF_CALS_NPI); > > + if (ret < 0) { > > + dev_err(&client->dev, "failed to clear als irq\n"); > > maybe consistent first letter: Failed vs failed > > > + return -EINVAL; > > + } > > + > > + /* Add chip off to automatically managed path */ > > + ret = devm_add_action_or_reset(&client->dev, > > + tsl2591_chip_off, > > + indio_dev); > > + if (ret < 0) > > + return -EINVAL; > > + > > + ret = devm_iio_device_register(&client->dev, indio_dev); > > + if (ret) { > > + dev_err(&client->dev, "iio registration failed\n"); > > probably not a very informative message > > > + return ret; > > + } > > + > > + dev_info(&client->dev, "Probe complete - tsl2591 found.\n"); > > message needed? > > > + > > + return 0; > > +} > > + > > +static const struct of_device_id tsl2591_of_match[] = { > > + { .compatible = "amstaos,tsl2591"}, > > + {}, > > +}; > > +MODULE_DEVICE_TABLE(of, tsl2591_of_match); > > + > > +static struct i2c_driver tsl2591_driver = { > > + .driver = { > > + .name = "tsl2591", > > + .pm = &tsl2591_pm_ops, > > + .of_match_table = tsl2591_of_match, > > + }, > > + .probe_new = tsl2591_probe, > > +}; > > +module_i2c_driver(tsl2591_driver); > > + > > +MODULE_AUTHOR("Joe Sandom <joe.sandom@outlook.com>"); > > +MODULE_DESCRIPTION("TAOS tsl2591 ambient light sensor driver"); > > +MODULE_LICENSE("GPL"); > > > > -- > > Peter Meerwald-Stadler > Mobile: +43 664 24 44 418 ^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2021-02-12 19:23 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
[not found] <DB8P195MB0728103C5874083BD441AA0D888D9@DB8P195MB0728.EURP195.PROD.OUTLOOK.COM>
2021-02-10 14:50 ` [PATCH v2] Added AMS tsl2591 driver implementation Peter Meerwald-Stadler
[not found] ` <DB8P195MB0728DA940A9CC57EA2D05F00888B9@DB8P195MB0728.EURP195.PROD.OUTLOOK.COM>
2021-02-12 19:22 ` Jonathan Cameron
2021-02-12 19:22 ` Jonathan Cameron
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).