[PATCH v4 00/15] Add support for AXP192 PMIC

[PATCH v4 00/15] Add support for AXP192 PMIC

[Aidan MacDonald]

Changes in v4:

* Drop regmap-irq patches and rebase on top of the regmap-irq
  refactoring series[1], which implements the same functionality.
* Reorder mfd_cells, putting one-line entries at the bottom.
* Fix incorrect example in axp192-gpio device tree bindings.
* Perform adc_en2 flag -> adc_en2_mask conversion in axp20x_adc
  as a separate patch.
* Simplify axp192_usb_power_set_current_max().
* Drop unneeded OF dependency in pin control driver, and document
  tables used for describing register layouts.
* Various style fixups suggested by Andy Shevchenko.

[1]: https://lore.kernel.org/lkml/20220623211420.918875-1-aidanmacdonald.0x0@gmail.com/

Changes in v3:

* Update pinctrl driver to address Andy Shevchenko's review comments
  from v1, and fix a few other issues.
* Add gpio-ranges property and example snippet to gpio DT bindings.
* Update commit message of patch 01/16 to point out that all register
  addresses are obtained using sub_irq_reg().
* Document ccc_table in axp20x_battery. Also update commit message to
  note a small fix that is part of that patch.
* Drop axp20x_adc consolidation patch in favor of using separate adc_raw
  functions. It's a minor code size optimization that may not be worth
  the effort due to implementation complexity.
* Use the FIELD_GET macro in axp20x_adc to further clarify intent.
* Fix a typo in the regulator driver where an AXP20X regulator ID was
  mistakenly used instead of an AXP192 regulator ID. Also carry over
  an Acked-by: tag from v1. Hope that's okay.
* Accumulate Acked-by: tags from v1 on DT patches.
* Accumulate Acked-by: tags from v2.

Note that regmap maintainer Mark Brown has said the first two patches to
regmap-irq aren't suitable for inclusion into the kernel in their current
state. I'm including them for v3 so the series remains testable.

Changes in v2:

* Do a little cleanup of axp20x_adc suggested by Jonathan Cameron
* Consolidate ADC read functions in axp20x_adc
* Drop the axp192's read_label callback in axp20x_adc
* Clean up the axp192-gpio dt bindings
* Rewrite a problematic bit of code in axp20x_usb_power reported
  by kernel test robot
* Support AXP192 in axp20x_battery
* Split up regmap-irq changes to two separate patches

Cover letter from v1:

Hi all,

This patch series adds support for the X-Powers AXP192 PMIC to the
AXP20x driver framework.

The first patch is a small change to regmap-irq to support the AXP192's
unusual IRQ register layout. It isn't possible to include all of the
IRQ registers in one regmap-irq chip without this.

The rest of the changes are pretty straightforward, I think the only
notable parts are the axp20x_adc driver where there seems to be some
opportunities for code reuse (the axp192 is nearly a duplicate of the
axp20x) and the addition of a new pinctrl driver for the axp192, since
the axp20x pinctrl driver was not very easy to adapt.

Aidan MacDonald (15):
  dt-bindings: mfd: add bindings for AXP192 MFD device
  dt-bindings: iio: adc: axp209: Add AXP192 compatible
  dt-bindings: power: supply: axp20x: Add AXP192 compatible
  dt-bindings: gpio: Add AXP192 GPIO bindings
  dt-bindings: power: axp20x-battery: Add AXP192 compatible
  mfd: axp20x: Add support for AXP192
  regulator: axp20x: Add support for AXP192
  iio: adc: axp20x_adc: Minor code cleanups
  iio: adc: axp20x_adc: Replace adc_en2 flag with adc_en2_mask field
  iio: adc: axp20x_adc: Add support for AXP192
  power: supply: axp20x_usb_power: Add support for AXP192
  pinctrl: Add AXP192 pin control driver
  power: axp20x_battery: Add constant charge current table
  power: axp20x_battery: Support battery status without fuel gauge
  power: axp20x_battery: Add support for AXP192

 .../bindings/gpio/x-powers,axp192-gpio.yaml   |  68 ++
 .../bindings/iio/adc/x-powers,axp209-adc.yaml |  18 +
 .../bindings/mfd/x-powers,axp152.yaml         |   1 +
 .../x-powers,axp20x-battery-power-supply.yaml |   1 +
 .../x-powers,axp20x-usb-power-supply.yaml     |   1 +
 drivers/iio/adc/axp20x_adc.c                  | 356 +++++++++--
 drivers/mfd/axp20x-i2c.c                      |   2 +
 drivers/mfd/axp20x.c                          | 152 +++++
 drivers/pinctrl/Kconfig                       |  13 +
 drivers/pinctrl/Makefile                      |   1 +
 drivers/pinctrl/pinctrl-axp192.c              | 598 ++++++++++++++++++
 drivers/power/supply/axp20x_battery.c         | 142 ++++-
 drivers/power/supply/axp20x_usb_power.c       |  84 ++-
 drivers/regulator/axp20x-regulator.c          | 100 ++-
 include/linux/mfd/axp20x.h                    |  84 +++
 15 files changed, 1547 insertions(+), 74 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/gpio/x-powers,axp192-gpio.yaml
 create mode 100644 drivers/pinctrl/pinctrl-axp192.c

-- 
2.35.1

[PATCH v4 01/15] dt-bindings: mfd: add bindings for AXP192 MFD device

[Aidan MacDonald]

The AXP192 is another X-Powers PMIC similar to the existing ones.

Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
---
 Documentation/devicetree/bindings/mfd/x-powers,axp152.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/mfd/x-powers,axp152.yaml b/Documentation/devicetree/bindings/mfd/x-powers,axp152.yaml
index 3a53bae611bc..33c9b1b3cc04 100644
--- a/Documentation/devicetree/bindings/mfd/x-powers,axp152.yaml
+++ b/Documentation/devicetree/bindings/mfd/x-powers,axp152.yaml
@@ -84,6 +84,7 @@ properties:
     oneOf:
       - enum:
           - x-powers,axp152
+          - x-powers,axp192
           - x-powers,axp202
           - x-powers,axp209
           - x-powers,axp221
-- 
2.35.1

[PATCH v4 02/15] dt-bindings: iio: adc: axp209: Add AXP192 compatible

[Aidan MacDonald]

The AXP192 is identical to the AXP20x, except for two additional
GPIO ADC channels.

Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
---
 .../bindings/iio/adc/x-powers,axp209-adc.yaml  | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/Documentation/devicetree/bindings/iio/adc/x-powers,axp209-adc.yaml b/Documentation/devicetree/bindings/iio/adc/x-powers,axp209-adc.yaml
index d6d3d8590171..1a68e650ac7d 100644
--- a/Documentation/devicetree/bindings/iio/adc/x-powers,axp209-adc.yaml
+++ b/Documentation/devicetree/bindings/iio/adc/x-powers,axp209-adc.yaml
@@ -14,6 +14,23 @@ description: |
   Device is a child of an axp209 multifunction device
   ADC channels and their indexes per variant:
 
+  AXP192
+  ------
+   0 | acin_v
+   1 | acin_i
+   2 | vbus_v
+   3 | vbus_i
+   4 | pmic_temp
+   5 | gpio0_v
+   6 | gpio1_v
+   7 | gpio2_v
+   8 | gpio3_v
+   9 | ipsout_v
+  10 | batt_v
+  11 | batt_chrg_i
+  12 | batt_dischrg_i
+  13 | ts_v
+
   AXP209
   ------
    0 | acin_v
@@ -50,6 +67,7 @@ description: |
 properties:
   compatible:
     oneOf:
+      - const: x-powers,axp192-adc
       - const: x-powers,axp209-adc
       - const: x-powers,axp221-adc
       - const: x-powers,axp813-adc
-- 
2.35.1

[PATCH v4 03/15] dt-bindings: power: supply: axp20x: Add AXP192 compatible

[Aidan MacDonald]

The AXP192's USB power supply is similar to the AXP202 but it has
different USB current limits and a different offset for the VBUS
status register.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
---
 .../bindings/power/supply/x-powers,axp20x-usb-power-supply.yaml  | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-usb-power-supply.yaml b/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-usb-power-supply.yaml
index 0c371b55c9e1..e800b3b97f0d 100644
--- a/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-usb-power-supply.yaml
+++ b/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-usb-power-supply.yaml
@@ -22,6 +22,7 @@ properties:
   compatible:
     oneOf:
       - enum:
+          - x-powers,axp192-usb-power-supply
           - x-powers,axp202-usb-power-supply
           - x-powers,axp221-usb-power-supply
           - x-powers,axp223-usb-power-supply
-- 
2.35.1

[PATCH v4 04/15] dt-bindings: gpio: Add AXP192 GPIO bindings

[Aidan MacDonald]

The AXP192 PMIC is different enough from the PMICs supported by
the AXP20x GPIO driver to warrant a separate driver. The AXP192
driver also supports interrupts and pinconf settings.

Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
---
 .../bindings/gpio/x-powers,axp192-gpio.yaml   | 68 +++++++++++++++++++
 1 file changed, 68 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/gpio/x-powers,axp192-gpio.yaml

diff --git a/Documentation/devicetree/bindings/gpio/x-powers,axp192-gpio.yaml b/Documentation/devicetree/bindings/gpio/x-powers,axp192-gpio.yaml
new file mode 100644
index 000000000000..ceb94aa2bc97
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/x-powers,axp192-gpio.yaml
@@ -0,0 +1,68 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/gpio/x-powers,axp192-gpio.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: X-Powers AXP192 GPIO Device Tree Bindings
+
+maintainers:
+  - Chen-Yu Tsai <wens@csie.org>
+
+properties:
+  compatible:
+    const: x-powers,axp192-gpio
+
+  gpio-controller: true
+
+  "#gpio-cells":
+    const: 2
+    description: >
+      The first cell is the pin number and the second is the GPIO flags.
+
+  gpio-ranges:
+    maxItems: 1
+
+patternProperties:
+  "-pins$":
+    $ref: /schemas/pinctrl/pinmux-node.yaml#
+
+    properties:
+      pins:
+        items:
+          enum:
+            - GPIO0
+            - GPIO1
+            - GPIO2
+            - GPIO3
+            - GPIO4
+            - N_RSTO
+
+      function:
+        enum:
+          - output
+          - input
+          - ldo
+          - pwm
+          - adc
+          - low_output
+          - floating
+          - ext_chg_ctl
+          - ldo_status
+
+required:
+  - compatible
+  - "#gpio-cells"
+  - gpio-controller
+  - gpio-ranges
+
+additionalProperties: false
+
+examples:
+  - |
+    pinctrl0: gpio {
+        compatible = "x-powers,axp192-gpio";
+        gpio-controller;
+        #gpio-cells = <2>;
+        gpio-ranges = <&pinctrl0 0 0 6>;
+    };
-- 
2.35.1

Re: [PATCH v4 04/15] dt-bindings: gpio: Add AXP192 GPIO bindings

[Krzysztof Kozlowski]

On 29/06/2022 16:30, Aidan MacDonald wrote:
> The AXP192 PMIC is different enough from the PMICs supported by
> the AXP20x GPIO driver to warrant a separate driver. The AXP192
> driver also supports interrupts and pinconf settings.
> 
> Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
> ---
>  .../bindings/gpio/x-powers,axp192-gpio.yaml   | 68 +++++++++++++++++++
>  1 file changed, 68 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/gpio/x-powers,axp192-gpio.yaml
> 
> diff --git a/Documentation/devicetree/bindings/gpio/x-powers,axp192-gpio.yaml b/Documentation/devicetree/bindings/gpio/x-powers,axp192-gpio.yaml
> new file mode 100644
> index 000000000000..ceb94aa2bc97
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/gpio/x-powers,axp192-gpio.yaml
> @@ -0,0 +1,68 @@
> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: "http://devicetree.org/schemas/gpio/x-powers,axp192-gpio.yaml#"
> +$schema: "http://devicetree.org/meta-schemas/core.yaml#"
> +

If there is going to be next version, please drop the quotes for these
two. In every patch.

Anyway:

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>


Best regards,
Krzysztof

Re: [PATCH v4 04/15] dt-bindings: gpio: Add AXP192 GPIO bindings

[Samuel Holland]

On 6/29/22 9:30 AM, Aidan MacDonald wrote:
> The AXP192 PMIC is different enough from the PMICs supported by
> the AXP20x GPIO driver to warrant a separate driver. The AXP192
> driver also supports interrupts and pinconf settings.
> 
> Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
> ---
>  .../bindings/gpio/x-powers,axp192-gpio.yaml   | 68 +++++++++++++++++++
>  1 file changed, 68 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/gpio/x-powers,axp192-gpio.yaml
> 
> diff --git a/Documentation/devicetree/bindings/gpio/x-powers,axp192-gpio.yaml b/Documentation/devicetree/bindings/gpio/x-powers,axp192-gpio.yaml
> new file mode 100644
> index 000000000000..ceb94aa2bc97
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/gpio/x-powers,axp192-gpio.yaml
> [...]
> +
> +required:
> +  - compatible
> +  - "#gpio-cells"
> +  - gpio-controller
> +  - gpio-ranges

By requiring the gpio-ranges property, you will not be able to convert the
existing driver, as existing devicetrees do not have it.

If you instead call pinctrl_add_gpio_range() from the driver, you can maintain
compatibility with the existing binding.

Regards,
Samuel

Re: [PATCH v4 04/15] dt-bindings: gpio: Add AXP192 GPIO bindings

[Aidan MacDonald]

Samuel Holland <samuel@sholland.org> writes:

> On 6/29/22 9:30 AM, Aidan MacDonald wrote:
>> The AXP192 PMIC is different enough from the PMICs supported by
>> the AXP20x GPIO driver to warrant a separate driver. The AXP192
>> driver also supports interrupts and pinconf settings.
>> 
>> Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
>> ---
>>  .../bindings/gpio/x-powers,axp192-gpio.yaml   | 68 +++++++++++++++++++
>>  1 file changed, 68 insertions(+)
>>  create mode 100644 Documentation/devicetree/bindings/gpio/x-powers,axp192-gpio.yaml
>> 
>> diff --git a/Documentation/devicetree/bindings/gpio/x-powers,axp192-gpio.yaml
>> b/Documentation/devicetree/bindings/gpio/x-powers,axp192-gpio.yaml
>> new file mode 100644
>> index 000000000000..ceb94aa2bc97
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/gpio/x-powers,axp192-gpio.yaml
>> [...]
>> +
>> +required:
>> +  - compatible
>> +  - "#gpio-cells"
>> +  - gpio-controller
>> +  - gpio-ranges
>
> By requiring the gpio-ranges property, you will not be able to convert the
> existing driver, as existing devicetrees do not have it.
>
> If you instead call pinctrl_add_gpio_range() from the driver, you can maintain
> compatibility with the existing binding.
>
> Regards,
> Samuel

Originally I did use pinctrl_add_gpio_range(), but calling that from
a pin control driver is apparently deprecated. It can be done from
->of_gpio_ranges_fallback to deal with old device trees, though.

[PATCH v4 05/15] dt-bindings: power: axp20x-battery: Add AXP192 compatible

[Aidan MacDonald]

The AXP192's battery charger is similar to the others supported by
the axp20x_battery driver.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
---
 .../power/supply/x-powers,axp20x-battery-power-supply.yaml       | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-battery-power-supply.yaml b/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-battery-power-supply.yaml
index d055428ae39f..b7347683a07e 100644
--- a/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-battery-power-supply.yaml
+++ b/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-battery-power-supply.yaml
@@ -20,6 +20,7 @@ allOf:
 properties:
   compatible:
     oneOf:
+      - const: x-powers,axp192-battery-power-supply
       - const: x-powers,axp202-battery-power-supply
       - const: x-powers,axp209-battery-power-supply
       - const: x-powers,axp221-battery-power-supply
-- 
2.35.1

[PATCH v4 06/15] mfd: axp20x: Add support for AXP192

[Aidan MacDonald]

The AXP192 PMIC is similar to the AXP202/AXP209, but with different
regulators, additional GPIOs, and a different IRQ register layout.

Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
---
 drivers/mfd/axp20x-i2c.c   |   2 +
 drivers/mfd/axp20x.c       | 152 +++++++++++++++++++++++++++++++++++++
 include/linux/mfd/axp20x.h |  84 ++++++++++++++++++++
 3 files changed, 238 insertions(+)

diff --git a/drivers/mfd/axp20x-i2c.c b/drivers/mfd/axp20x-i2c.c
index 00ab48018d8d..9ada58fad77f 100644
--- a/drivers/mfd/axp20x-i2c.c
+++ b/drivers/mfd/axp20x-i2c.c
@@ -62,6 +62,7 @@ static int axp20x_i2c_remove(struct i2c_client *i2c)
 #ifdef CONFIG_OF
 static const struct of_device_id axp20x_i2c_of_match[] = {
 	{ .compatible = "x-powers,axp152", .data = (void *)AXP152_ID },
+	{ .compatible = "x-powers,axp192", .data = (void *)AXP192_ID },
 	{ .compatible = "x-powers,axp202", .data = (void *)AXP202_ID },
 	{ .compatible = "x-powers,axp209", .data = (void *)AXP209_ID },
 	{ .compatible = "x-powers,axp221", .data = (void *)AXP221_ID },
@@ -75,6 +76,7 @@ MODULE_DEVICE_TABLE(of, axp20x_i2c_of_match);
 
 static const struct i2c_device_id axp20x_i2c_id[] = {
 	{ "axp152", 0 },
+	{ "axp192", 0 },
 	{ "axp202", 0 },
 	{ "axp209", 0 },
 	{ "axp221", 0 },
diff --git a/drivers/mfd/axp20x.c b/drivers/mfd/axp20x.c
index 8161a5dc68e8..6ab2a1f8888c 100644
--- a/drivers/mfd/axp20x.c
+++ b/drivers/mfd/axp20x.c
@@ -34,6 +34,7 @@
 
 static const char * const axp20x_model_names[] = {
 	"AXP152",
+	"AXP192",
 	"AXP202",
 	"AXP209",
 	"AXP221",
@@ -92,6 +93,35 @@ static const struct regmap_access_table axp20x_volatile_table = {
 	.n_yes_ranges	= ARRAY_SIZE(axp20x_volatile_ranges),
 };
 
+static const struct regmap_range axp192_writeable_ranges[] = {
+	regmap_reg_range(AXP192_DATACACHE(0), AXP192_DATACACHE(5)),
+	regmap_reg_range(AXP192_PWR_OUT_CTRL, AXP192_IRQ5_STATE),
+	regmap_reg_range(AXP20X_DCDC_MODE, AXP192_N_RSTO_CTRL),
+	regmap_reg_range(AXP20X_CC_CTRL, AXP20X_CC_CTRL),
+};
+
+static const struct regmap_range axp192_volatile_ranges[] = {
+	regmap_reg_range(AXP20X_PWR_INPUT_STATUS, AXP192_USB_OTG_STATUS),
+	regmap_reg_range(AXP192_IRQ1_STATE, AXP192_IRQ4_STATE),
+	regmap_reg_range(AXP192_IRQ5_STATE, AXP192_IRQ5_STATE),
+	regmap_reg_range(AXP20X_ACIN_V_ADC_H, AXP20X_IPSOUT_V_HIGH_L),
+	regmap_reg_range(AXP20X_TIMER_CTRL, AXP20X_TIMER_CTRL),
+	regmap_reg_range(AXP192_GPIO2_0_STATE, AXP192_GPIO2_0_STATE),
+	regmap_reg_range(AXP192_GPIO4_3_STATE, AXP192_GPIO4_3_STATE),
+	regmap_reg_range(AXP192_N_RSTO_CTRL, AXP192_N_RSTO_CTRL),
+	regmap_reg_range(AXP20X_CHRG_CC_31_24, AXP20X_CC_CTRL),
+};
+
+static const struct regmap_access_table axp192_writeable_table = {
+	.yes_ranges	= axp192_writeable_ranges,
+	.n_yes_ranges	= ARRAY_SIZE(axp192_writeable_ranges),
+};
+
+static const struct regmap_access_table axp192_volatile_table = {
+	.yes_ranges	= axp192_volatile_ranges,
+	.n_yes_ranges	= ARRAY_SIZE(axp192_volatile_ranges),
+};
+
 /* AXP22x ranges are shared with the AXP809, as they cover the same range */
 static const struct regmap_range axp22x_writeable_ranges[] = {
 	regmap_reg_range(AXP20X_DATACACHE(0), AXP20X_IRQ5_STATE),
@@ -173,6 +203,25 @@ static const struct resource axp152_pek_resources[] = {
 	DEFINE_RES_IRQ_NAMED(AXP152_IRQ_PEK_FAL_EDGE, "PEK_DBF"),
 };
 
+static const struct resource axp192_gpio_resources[] = {
+	DEFINE_RES_IRQ_NAMED(AXP192_IRQ_GPIO0_INPUT, "GPIO0"),
+	DEFINE_RES_IRQ_NAMED(AXP192_IRQ_GPIO1_INPUT, "GPIO1"),
+	DEFINE_RES_IRQ_NAMED(AXP192_IRQ_GPIO2_INPUT, "GPIO2"),
+};
+
+static const struct resource axp192_ac_power_supply_resources[] = {
+	DEFINE_RES_IRQ_NAMED(AXP192_IRQ_ACIN_PLUGIN, "ACIN_PLUGIN"),
+	DEFINE_RES_IRQ_NAMED(AXP192_IRQ_ACIN_REMOVAL, "ACIN_REMOVAL"),
+	DEFINE_RES_IRQ_NAMED(AXP192_IRQ_ACIN_OVER_V, "ACIN_OVER_V"),
+};
+
+static const struct resource axp192_usb_power_supply_resources[] = {
+	DEFINE_RES_IRQ_NAMED(AXP192_IRQ_VBUS_PLUGIN, "VBUS_PLUGIN"),
+	DEFINE_RES_IRQ_NAMED(AXP192_IRQ_VBUS_REMOVAL, "VBUS_REMOVAL"),
+	DEFINE_RES_IRQ_NAMED(AXP192_IRQ_VBUS_VALID, "VBUS_VALID"),
+	DEFINE_RES_IRQ_NAMED(AXP192_IRQ_VBUS_NOT_VALID, "VBUS_NOT_VALID"),
+};
+
 static const struct resource axp20x_ac_power_supply_resources[] = {
 	DEFINE_RES_IRQ_NAMED(AXP20X_IRQ_ACIN_PLUGIN, "ACIN_PLUGIN"),
 	DEFINE_RES_IRQ_NAMED(AXP20X_IRQ_ACIN_REMOVAL, "ACIN_REMOVAL"),
@@ -245,6 +294,15 @@ static const struct regmap_config axp152_regmap_config = {
 	.cache_type	= REGCACHE_RBTREE,
 };
 
+static const struct regmap_config axp192_regmap_config = {
+	.reg_bits	= 8,
+	.val_bits	= 8,
+	.wr_table	= &axp192_writeable_table,
+	.volatile_table	= &axp192_volatile_table,
+	.max_register	= AXP20X_CC_CTRL,
+	.cache_type	= REGCACHE_RBTREE,
+};
+
 static const struct regmap_config axp20x_regmap_config = {
 	.reg_bits	= 8,
 	.val_bits	= 8,
@@ -304,6 +362,42 @@ static const struct regmap_irq axp152_regmap_irqs[] = {
 	INIT_REGMAP_IRQ(AXP152, GPIO0_INPUT,		2, 0),
 };
 
+static const struct regmap_irq axp192_regmap_irqs[] = {
+	INIT_REGMAP_IRQ(AXP192, ACIN_OVER_V,		0, 7),
+	INIT_REGMAP_IRQ(AXP192, ACIN_PLUGIN,		0, 6),
+	INIT_REGMAP_IRQ(AXP192, ACIN_REMOVAL,		0, 5),
+	INIT_REGMAP_IRQ(AXP192, VBUS_OVER_V,		0, 4),
+	INIT_REGMAP_IRQ(AXP192, VBUS_PLUGIN,		0, 3),
+	INIT_REGMAP_IRQ(AXP192, VBUS_REMOVAL,		0, 2),
+	INIT_REGMAP_IRQ(AXP192, VBUS_V_LOW,		0, 1),
+	INIT_REGMAP_IRQ(AXP192, BATT_PLUGIN,		1, 7),
+	INIT_REGMAP_IRQ(AXP192, BATT_REMOVAL,	        1, 6),
+	INIT_REGMAP_IRQ(AXP192, BATT_ENT_ACT_MODE,	1, 5),
+	INIT_REGMAP_IRQ(AXP192, BATT_EXIT_ACT_MODE,	1, 4),
+	INIT_REGMAP_IRQ(AXP192, CHARG,		        1, 3),
+	INIT_REGMAP_IRQ(AXP192, CHARG_DONE,		1, 2),
+	INIT_REGMAP_IRQ(AXP192, BATT_TEMP_HIGH,	        1, 1),
+	INIT_REGMAP_IRQ(AXP192, BATT_TEMP_LOW,	        1, 0),
+	INIT_REGMAP_IRQ(AXP192, DIE_TEMP_HIGH,	        2, 7),
+	INIT_REGMAP_IRQ(AXP192, CHARG_I_LOW,		2, 6),
+	INIT_REGMAP_IRQ(AXP192, DCDC1_V_LONG,	        2, 5),
+	INIT_REGMAP_IRQ(AXP192, DCDC2_V_LONG,	        2, 4),
+	INIT_REGMAP_IRQ(AXP192, DCDC3_V_LONG,	        2, 3),
+	INIT_REGMAP_IRQ(AXP192, PEK_SHORT,		2, 1),
+	INIT_REGMAP_IRQ(AXP192, PEK_LONG,		2, 0),
+	INIT_REGMAP_IRQ(AXP192, N_OE_PWR_ON,		3, 7),
+	INIT_REGMAP_IRQ(AXP192, N_OE_PWR_OFF,	        3, 6),
+	INIT_REGMAP_IRQ(AXP192, VBUS_VALID,		3, 5),
+	INIT_REGMAP_IRQ(AXP192, VBUS_NOT_VALID,	        3, 4),
+	INIT_REGMAP_IRQ(AXP192, VBUS_SESS_VALID,	3, 3),
+	INIT_REGMAP_IRQ(AXP192, VBUS_SESS_END,	        3, 2),
+	INIT_REGMAP_IRQ(AXP192, LOW_PWR_LVL,	        3, 0),
+	INIT_REGMAP_IRQ(AXP192, TIMER,			4, 7),
+	INIT_REGMAP_IRQ(AXP192, GPIO2_INPUT,		4, 2),
+	INIT_REGMAP_IRQ(AXP192, GPIO1_INPUT,		4, 1),
+	INIT_REGMAP_IRQ(AXP192, GPIO0_INPUT,		4, 0),
+};
+
 static const struct regmap_irq axp20x_regmap_irqs[] = {
 	INIT_REGMAP_IRQ(AXP20X, ACIN_OVER_V,		0, 7),
 	INIT_REGMAP_IRQ(AXP20X, ACIN_PLUGIN,		0, 6),
@@ -514,6 +608,32 @@ static const struct regmap_irq_chip axp152_regmap_irq_chip = {
 	.num_regs		= 3,
 };
 
+static unsigned int axp192_get_irq_reg(struct regmap_irq_chip_data *data,
+				       unsigned int base, int index)
+{
+	/* linear mapping for IRQ1 to IRQ4 */
+	if (index < 4)
+		return base + index;
+
+	/* handle IRQ5 separately */
+	if (base == AXP192_IRQ1_EN)
+		return AXP192_IRQ5_EN;
+
+	return AXP192_IRQ5_STATE;
+}
+
+static const struct regmap_irq_chip axp192_regmap_irq_chip = {
+	.name			= "axp192_irq_chip",
+	.status_base		= AXP192_IRQ1_STATE,
+	.ack_base		= AXP192_IRQ1_STATE,
+	.unmask_base		= AXP192_IRQ1_EN,
+	.init_ack_masked	= true,
+	.irqs			= axp192_regmap_irqs,
+	.num_irqs		= ARRAY_SIZE(axp192_regmap_irqs),
+	.num_regs		= 5,
+	.get_irq_reg		= axp192_get_irq_reg,
+};
+
 static const struct regmap_irq_chip axp20x_regmap_irq_chip = {
 	.name			= "axp20x_irq_chip",
 	.status_base		= AXP20X_IRQ1_STATE,
@@ -588,6 +708,32 @@ static const struct regmap_irq_chip axp809_regmap_irq_chip = {
 	.num_regs		= 5,
 };
 
+static const struct mfd_cell axp192_cells[] = {
+	{
+		.name		= "axp192-gpio",
+		.of_compatible	= "x-powers,axp192-gpio",
+		.num_resources	= ARRAY_SIZE(axp192_gpio_resources),
+		.resources	= axp192_gpio_resources,
+	}, {
+		.name		= "axp192-adc",
+		.of_compatible	= "x-powers,axp192-adc",
+	}, {
+		.name		= "axp20x-battery-power-supply",
+		.of_compatible	= "x-powers,axp192-battery-power-supply",
+	}, {
+		.name		= "axp20x-ac-power-supply",
+		.of_compatible	= "x-powers,axp202-ac-power-supply",
+		.num_resources	= ARRAY_SIZE(axp192_ac_power_supply_resources),
+		.resources	= axp192_ac_power_supply_resources,
+	}, {
+		.name		= "axp20x-usb-power-supply",
+		.of_compatible	= "x-powers,axp192-usb-power-supply",
+		.num_resources	= ARRAY_SIZE(axp192_usb_power_supply_resources),
+		.resources	= axp192_usb_power_supply_resources,
+	},
+	{	.name		= "axp20x-regulator" },
+};
+
 static const struct mfd_cell axp20x_cells[] = {
 	{
 		.name		= "axp20x-gpio",
@@ -865,6 +1011,12 @@ int axp20x_match_device(struct axp20x_dev *axp20x)
 		axp20x->regmap_cfg = &axp152_regmap_config;
 		axp20x->regmap_irq_chip = &axp152_regmap_irq_chip;
 		break;
+	case AXP192_ID:
+		axp20x->nr_cells = ARRAY_SIZE(axp192_cells);
+		axp20x->cells = axp192_cells;
+		axp20x->regmap_cfg = &axp192_regmap_config;
+		axp20x->regmap_irq_chip = &axp192_regmap_irq_chip;
+		break;
 	case AXP202_ID:
 	case AXP209_ID:
 		axp20x->nr_cells = ARRAY_SIZE(axp20x_cells);
diff --git a/include/linux/mfd/axp20x.h b/include/linux/mfd/axp20x.h
index 9ab0e2fca7ea..c9a9ee8ec246 100644
--- a/include/linux/mfd/axp20x.h
+++ b/include/linux/mfd/axp20x.h
@@ -12,6 +12,7 @@
 
 enum axp20x_variants {
 	AXP152_ID = 0,
+	AXP192_ID,
 	AXP202_ID,
 	AXP209_ID,
 	AXP221_ID,
@@ -24,6 +25,7 @@ enum axp20x_variants {
 	NR_AXP20X_VARIANTS,
 };
 
+#define AXP192_DATACACHE(m)		(0x06 + (m))
 #define AXP20X_DATACACHE(m)		(0x04 + (m))
 
 /* Power supply */
@@ -45,6 +47,13 @@ enum axp20x_variants {
 #define AXP152_DCDC_FREQ		0x37
 #define AXP152_DCDC_MODE		0x80
 
+#define AXP192_USB_OTG_STATUS		0x04
+#define AXP192_PWR_OUT_CTRL		0x12
+#define AXP192_DCDC2_V_OUT		0x23
+#define AXP192_DCDC1_V_OUT		0x26
+#define AXP192_DCDC3_V_OUT		0x27
+#define AXP192_LDO2_3_V_OUT		0x28
+
 #define AXP20X_PWR_INPUT_STATUS		0x00
 #define AXP20X_PWR_OP_MODE		0x01
 #define AXP20X_USB_OTG_STATUS		0x02
@@ -139,6 +148,17 @@ enum axp20x_variants {
 #define AXP152_IRQ2_STATE		0x49
 #define AXP152_IRQ3_STATE		0x4a
 
+#define AXP192_IRQ1_EN			0x40
+#define AXP192_IRQ2_EN			0x41
+#define AXP192_IRQ3_EN			0x42
+#define AXP192_IRQ4_EN			0x43
+#define AXP192_IRQ1_STATE		0x44
+#define AXP192_IRQ2_STATE		0x45
+#define AXP192_IRQ3_STATE		0x46
+#define AXP192_IRQ4_STATE		0x47
+#define AXP192_IRQ5_EN			0x4a
+#define AXP192_IRQ5_STATE		0x4d
+
 #define AXP20X_IRQ1_EN			0x40
 #define AXP20X_IRQ2_EN			0x41
 #define AXP20X_IRQ3_EN			0x42
@@ -153,6 +173,11 @@ enum axp20x_variants {
 #define AXP20X_IRQ6_STATE		0x4d
 
 /* ADC */
+#define AXP192_GPIO2_V_ADC_H		0x68
+#define AXP192_GPIO2_V_ADC_L		0x69
+#define AXP192_GPIO3_V_ADC_H		0x6a
+#define AXP192_GPIO3_V_ADC_L		0x6b
+
 #define AXP20X_ACIN_V_ADC_H		0x56
 #define AXP20X_ACIN_V_ADC_L		0x57
 #define AXP20X_ACIN_I_ADC_H		0x58
@@ -182,6 +207,8 @@ enum axp20x_variants {
 #define AXP20X_IPSOUT_V_HIGH_L		0x7f
 
 /* Power supply */
+#define AXP192_GPIO30_IN_RANGE		0x85
+
 #define AXP20X_DCDC_MODE		0x80
 #define AXP20X_ADC_EN1			0x82
 #define AXP20X_ADC_EN2			0x83
@@ -210,6 +237,16 @@ enum axp20x_variants {
 #define AXP152_PWM1_FREQ_Y		0x9c
 #define AXP152_PWM1_DUTY_CYCLE		0x9d
 
+#define AXP192_GPIO0_CTRL		0x90
+#define AXP192_LDO_IO0_V_OUT		0x91
+#define AXP192_GPIO1_CTRL		0x92
+#define AXP192_GPIO2_CTRL		0x93
+#define AXP192_GPIO2_0_STATE		0x94
+#define AXP192_GPIO4_3_CTRL		0x95
+#define AXP192_GPIO4_3_STATE		0x96
+#define AXP192_GPIO2_0_PULL		0x97
+#define AXP192_N_RSTO_CTRL		0x9e
+
 #define AXP20X_GPIO0_CTRL		0x90
 #define AXP20X_LDO5_V_OUT		0x91
 #define AXP20X_GPIO1_CTRL		0x92
@@ -287,6 +324,17 @@ enum axp20x_variants {
 #define AXP288_FG_TUNE5             0xed
 
 /* Regulators IDs */
+enum {
+	AXP192_DCDC1 = 0,
+	AXP192_DCDC2,
+	AXP192_DCDC3,
+	AXP192_LDO1,
+	AXP192_LDO2,
+	AXP192_LDO3,
+	AXP192_LDO_IO0,
+	AXP192_REG_ID_MAX
+};
+
 enum {
 	AXP20X_LDO1 = 0,
 	AXP20X_LDO2,
@@ -440,6 +488,42 @@ enum {
 	AXP152_IRQ_GPIO0_INPUT,
 };
 
+enum axp192_irqs {
+	AXP192_IRQ_ACIN_OVER_V = 1,
+	AXP192_IRQ_ACIN_PLUGIN,
+	AXP192_IRQ_ACIN_REMOVAL,
+	AXP192_IRQ_VBUS_OVER_V,
+	AXP192_IRQ_VBUS_PLUGIN,
+	AXP192_IRQ_VBUS_REMOVAL,
+	AXP192_IRQ_VBUS_V_LOW,
+	AXP192_IRQ_BATT_PLUGIN,
+	AXP192_IRQ_BATT_REMOVAL,
+	AXP192_IRQ_BATT_ENT_ACT_MODE,
+	AXP192_IRQ_BATT_EXIT_ACT_MODE,
+	AXP192_IRQ_CHARG,
+	AXP192_IRQ_CHARG_DONE,
+	AXP192_IRQ_BATT_TEMP_HIGH,
+	AXP192_IRQ_BATT_TEMP_LOW,
+	AXP192_IRQ_DIE_TEMP_HIGH,
+	AXP192_IRQ_CHARG_I_LOW,
+	AXP192_IRQ_DCDC1_V_LONG,
+	AXP192_IRQ_DCDC2_V_LONG,
+	AXP192_IRQ_DCDC3_V_LONG,
+	AXP192_IRQ_PEK_SHORT = 22,
+	AXP192_IRQ_PEK_LONG,
+	AXP192_IRQ_N_OE_PWR_ON,
+	AXP192_IRQ_N_OE_PWR_OFF,
+	AXP192_IRQ_VBUS_VALID,
+	AXP192_IRQ_VBUS_NOT_VALID,
+	AXP192_IRQ_VBUS_SESS_VALID,
+	AXP192_IRQ_VBUS_SESS_END,
+	AXP192_IRQ_LOW_PWR_LVL = 31,
+	AXP192_IRQ_TIMER,
+	AXP192_IRQ_GPIO2_INPUT = 37,
+	AXP192_IRQ_GPIO1_INPUT,
+	AXP192_IRQ_GPIO0_INPUT,
+};
+
 enum {
 	AXP20X_IRQ_ACIN_OVER_V = 1,
 	AXP20X_IRQ_ACIN_PLUGIN,
-- 
2.35.1

Re: [PATCH v4 06/15] mfd: axp20x: Add support for AXP192

[Andy Shevchenko]

On Wed, Jun 29, 2022 at 4:29 PM Aidan MacDonald
<aidanmacdonald.0x0@gmail.com> wrote:
>
> The AXP192 PMIC is similar to the AXP202/AXP209, but with different
> regulators, additional GPIOs, and a different IRQ register layout.

Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>

> Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
> Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
> ---
>  drivers/mfd/axp20x-i2c.c   |   2 +
>  drivers/mfd/axp20x.c       | 152 +++++++++++++++++++++++++++++++++++++
>  include/linux/mfd/axp20x.h |  84 ++++++++++++++++++++
>  3 files changed, 238 insertions(+)
>
> diff --git a/drivers/mfd/axp20x-i2c.c b/drivers/mfd/axp20x-i2c.c
> index 00ab48018d8d..9ada58fad77f 100644
> --- a/drivers/mfd/axp20x-i2c.c
> +++ b/drivers/mfd/axp20x-i2c.c
> @@ -62,6 +62,7 @@ static int axp20x_i2c_remove(struct i2c_client *i2c)
>  #ifdef CONFIG_OF
>  static const struct of_device_id axp20x_i2c_of_match[] = {
>         { .compatible = "x-powers,axp152", .data = (void *)AXP152_ID },
> +       { .compatible = "x-powers,axp192", .data = (void *)AXP192_ID },
>         { .compatible = "x-powers,axp202", .data = (void *)AXP202_ID },
>         { .compatible = "x-powers,axp209", .data = (void *)AXP209_ID },
>         { .compatible = "x-powers,axp221", .data = (void *)AXP221_ID },
> @@ -75,6 +76,7 @@ MODULE_DEVICE_TABLE(of, axp20x_i2c_of_match);
>
>  static const struct i2c_device_id axp20x_i2c_id[] = {
>         { "axp152", 0 },
> +       { "axp192", 0 },
>         { "axp202", 0 },
>         { "axp209", 0 },
>         { "axp221", 0 },
> diff --git a/drivers/mfd/axp20x.c b/drivers/mfd/axp20x.c
> index 8161a5dc68e8..6ab2a1f8888c 100644
> --- a/drivers/mfd/axp20x.c
> +++ b/drivers/mfd/axp20x.c
> @@ -34,6 +34,7 @@
>
>  static const char * const axp20x_model_names[] = {
>         "AXP152",
> +       "AXP192",
>         "AXP202",
>         "AXP209",
>         "AXP221",
> @@ -92,6 +93,35 @@ static const struct regmap_access_table axp20x_volatile_table = {
>         .n_yes_ranges   = ARRAY_SIZE(axp20x_volatile_ranges),
>  };
>
> +static const struct regmap_range axp192_writeable_ranges[] = {
> +       regmap_reg_range(AXP192_DATACACHE(0), AXP192_DATACACHE(5)),
> +       regmap_reg_range(AXP192_PWR_OUT_CTRL, AXP192_IRQ5_STATE),
> +       regmap_reg_range(AXP20X_DCDC_MODE, AXP192_N_RSTO_CTRL),
> +       regmap_reg_range(AXP20X_CC_CTRL, AXP20X_CC_CTRL),
> +};
> +
> +static const struct regmap_range axp192_volatile_ranges[] = {
> +       regmap_reg_range(AXP20X_PWR_INPUT_STATUS, AXP192_USB_OTG_STATUS),
> +       regmap_reg_range(AXP192_IRQ1_STATE, AXP192_IRQ4_STATE),
> +       regmap_reg_range(AXP192_IRQ5_STATE, AXP192_IRQ5_STATE),
> +       regmap_reg_range(AXP20X_ACIN_V_ADC_H, AXP20X_IPSOUT_V_HIGH_L),
> +       regmap_reg_range(AXP20X_TIMER_CTRL, AXP20X_TIMER_CTRL),
> +       regmap_reg_range(AXP192_GPIO2_0_STATE, AXP192_GPIO2_0_STATE),
> +       regmap_reg_range(AXP192_GPIO4_3_STATE, AXP192_GPIO4_3_STATE),
> +       regmap_reg_range(AXP192_N_RSTO_CTRL, AXP192_N_RSTO_CTRL),
> +       regmap_reg_range(AXP20X_CHRG_CC_31_24, AXP20X_CC_CTRL),
> +};
> +
> +static const struct regmap_access_table axp192_writeable_table = {
> +       .yes_ranges     = axp192_writeable_ranges,
> +       .n_yes_ranges   = ARRAY_SIZE(axp192_writeable_ranges),
> +};
> +
> +static const struct regmap_access_table axp192_volatile_table = {
> +       .yes_ranges     = axp192_volatile_ranges,
> +       .n_yes_ranges   = ARRAY_SIZE(axp192_volatile_ranges),
> +};
> +
>  /* AXP22x ranges are shared with the AXP809, as they cover the same range */
>  static const struct regmap_range axp22x_writeable_ranges[] = {
>         regmap_reg_range(AXP20X_DATACACHE(0), AXP20X_IRQ5_STATE),
> @@ -173,6 +203,25 @@ static const struct resource axp152_pek_resources[] = {
>         DEFINE_RES_IRQ_NAMED(AXP152_IRQ_PEK_FAL_EDGE, "PEK_DBF"),
>  };
>
> +static const struct resource axp192_gpio_resources[] = {
> +       DEFINE_RES_IRQ_NAMED(AXP192_IRQ_GPIO0_INPUT, "GPIO0"),
> +       DEFINE_RES_IRQ_NAMED(AXP192_IRQ_GPIO1_INPUT, "GPIO1"),
> +       DEFINE_RES_IRQ_NAMED(AXP192_IRQ_GPIO2_INPUT, "GPIO2"),
> +};
> +
> +static const struct resource axp192_ac_power_supply_resources[] = {
> +       DEFINE_RES_IRQ_NAMED(AXP192_IRQ_ACIN_PLUGIN, "ACIN_PLUGIN"),
> +       DEFINE_RES_IRQ_NAMED(AXP192_IRQ_ACIN_REMOVAL, "ACIN_REMOVAL"),
> +       DEFINE_RES_IRQ_NAMED(AXP192_IRQ_ACIN_OVER_V, "ACIN_OVER_V"),
> +};
> +
> +static const struct resource axp192_usb_power_supply_resources[] = {
> +       DEFINE_RES_IRQ_NAMED(AXP192_IRQ_VBUS_PLUGIN, "VBUS_PLUGIN"),
> +       DEFINE_RES_IRQ_NAMED(AXP192_IRQ_VBUS_REMOVAL, "VBUS_REMOVAL"),
> +       DEFINE_RES_IRQ_NAMED(AXP192_IRQ_VBUS_VALID, "VBUS_VALID"),
> +       DEFINE_RES_IRQ_NAMED(AXP192_IRQ_VBUS_NOT_VALID, "VBUS_NOT_VALID"),
> +};
> +
>  static const struct resource axp20x_ac_power_supply_resources[] = {
>         DEFINE_RES_IRQ_NAMED(AXP20X_IRQ_ACIN_PLUGIN, "ACIN_PLUGIN"),
>         DEFINE_RES_IRQ_NAMED(AXP20X_IRQ_ACIN_REMOVAL, "ACIN_REMOVAL"),
> @@ -245,6 +294,15 @@ static const struct regmap_config axp152_regmap_config = {
>         .cache_type     = REGCACHE_RBTREE,
>  };
>
> +static const struct regmap_config axp192_regmap_config = {
> +       .reg_bits       = 8,
> +       .val_bits       = 8,
> +       .wr_table       = &axp192_writeable_table,
> +       .volatile_table = &axp192_volatile_table,
> +       .max_register   = AXP20X_CC_CTRL,
> +       .cache_type     = REGCACHE_RBTREE,
> +};
> +
>  static const struct regmap_config axp20x_regmap_config = {
>         .reg_bits       = 8,
>         .val_bits       = 8,
> @@ -304,6 +362,42 @@ static const struct regmap_irq axp152_regmap_irqs[] = {
>         INIT_REGMAP_IRQ(AXP152, GPIO0_INPUT,            2, 0),
>  };
>
> +static const struct regmap_irq axp192_regmap_irqs[] = {
> +       INIT_REGMAP_IRQ(AXP192, ACIN_OVER_V,            0, 7),
> +       INIT_REGMAP_IRQ(AXP192, ACIN_PLUGIN,            0, 6),
> +       INIT_REGMAP_IRQ(AXP192, ACIN_REMOVAL,           0, 5),
> +       INIT_REGMAP_IRQ(AXP192, VBUS_OVER_V,            0, 4),
> +       INIT_REGMAP_IRQ(AXP192, VBUS_PLUGIN,            0, 3),
> +       INIT_REGMAP_IRQ(AXP192, VBUS_REMOVAL,           0, 2),
> +       INIT_REGMAP_IRQ(AXP192, VBUS_V_LOW,             0, 1),
> +       INIT_REGMAP_IRQ(AXP192, BATT_PLUGIN,            1, 7),
> +       INIT_REGMAP_IRQ(AXP192, BATT_REMOVAL,           1, 6),
> +       INIT_REGMAP_IRQ(AXP192, BATT_ENT_ACT_MODE,      1, 5),
> +       INIT_REGMAP_IRQ(AXP192, BATT_EXIT_ACT_MODE,     1, 4),
> +       INIT_REGMAP_IRQ(AXP192, CHARG,                  1, 3),
> +       INIT_REGMAP_IRQ(AXP192, CHARG_DONE,             1, 2),
> +       INIT_REGMAP_IRQ(AXP192, BATT_TEMP_HIGH,         1, 1),
> +       INIT_REGMAP_IRQ(AXP192, BATT_TEMP_LOW,          1, 0),
> +       INIT_REGMAP_IRQ(AXP192, DIE_TEMP_HIGH,          2, 7),
> +       INIT_REGMAP_IRQ(AXP192, CHARG_I_LOW,            2, 6),
> +       INIT_REGMAP_IRQ(AXP192, DCDC1_V_LONG,           2, 5),
> +       INIT_REGMAP_IRQ(AXP192, DCDC2_V_LONG,           2, 4),
> +       INIT_REGMAP_IRQ(AXP192, DCDC3_V_LONG,           2, 3),
> +       INIT_REGMAP_IRQ(AXP192, PEK_SHORT,              2, 1),
> +       INIT_REGMAP_IRQ(AXP192, PEK_LONG,               2, 0),
> +       INIT_REGMAP_IRQ(AXP192, N_OE_PWR_ON,            3, 7),
> +       INIT_REGMAP_IRQ(AXP192, N_OE_PWR_OFF,           3, 6),
> +       INIT_REGMAP_IRQ(AXP192, VBUS_VALID,             3, 5),
> +       INIT_REGMAP_IRQ(AXP192, VBUS_NOT_VALID,         3, 4),
> +       INIT_REGMAP_IRQ(AXP192, VBUS_SESS_VALID,        3, 3),
> +       INIT_REGMAP_IRQ(AXP192, VBUS_SESS_END,          3, 2),
> +       INIT_REGMAP_IRQ(AXP192, LOW_PWR_LVL,            3, 0),
> +       INIT_REGMAP_IRQ(AXP192, TIMER,                  4, 7),
> +       INIT_REGMAP_IRQ(AXP192, GPIO2_INPUT,            4, 2),
> +       INIT_REGMAP_IRQ(AXP192, GPIO1_INPUT,            4, 1),
> +       INIT_REGMAP_IRQ(AXP192, GPIO0_INPUT,            4, 0),
> +};
> +
>  static const struct regmap_irq axp20x_regmap_irqs[] = {
>         INIT_REGMAP_IRQ(AXP20X, ACIN_OVER_V,            0, 7),
>         INIT_REGMAP_IRQ(AXP20X, ACIN_PLUGIN,            0, 6),
> @@ -514,6 +608,32 @@ static const struct regmap_irq_chip axp152_regmap_irq_chip = {
>         .num_regs               = 3,
>  };
>
> +static unsigned int axp192_get_irq_reg(struct regmap_irq_chip_data *data,
> +                                      unsigned int base, int index)
> +{
> +       /* linear mapping for IRQ1 to IRQ4 */
> +       if (index < 4)
> +               return base + index;
> +
> +       /* handle IRQ5 separately */
> +       if (base == AXP192_IRQ1_EN)
> +               return AXP192_IRQ5_EN;
> +
> +       return AXP192_IRQ5_STATE;
> +}
> +
> +static const struct regmap_irq_chip axp192_regmap_irq_chip = {
> +       .name                   = "axp192_irq_chip",
> +       .status_base            = AXP192_IRQ1_STATE,
> +       .ack_base               = AXP192_IRQ1_STATE,
> +       .unmask_base            = AXP192_IRQ1_EN,
> +       .init_ack_masked        = true,
> +       .irqs                   = axp192_regmap_irqs,
> +       .num_irqs               = ARRAY_SIZE(axp192_regmap_irqs),
> +       .num_regs               = 5,
> +       .get_irq_reg            = axp192_get_irq_reg,
> +};
> +
>  static const struct regmap_irq_chip axp20x_regmap_irq_chip = {
>         .name                   = "axp20x_irq_chip",
>         .status_base            = AXP20X_IRQ1_STATE,
> @@ -588,6 +708,32 @@ static const struct regmap_irq_chip axp809_regmap_irq_chip = {
>         .num_regs               = 5,
>  };
>
> +static const struct mfd_cell axp192_cells[] = {
> +       {
> +               .name           = "axp192-gpio",
> +               .of_compatible  = "x-powers,axp192-gpio",
> +               .num_resources  = ARRAY_SIZE(axp192_gpio_resources),
> +               .resources      = axp192_gpio_resources,
> +       }, {
> +               .name           = "axp192-adc",
> +               .of_compatible  = "x-powers,axp192-adc",
> +       }, {
> +               .name           = "axp20x-battery-power-supply",
> +               .of_compatible  = "x-powers,axp192-battery-power-supply",
> +       }, {
> +               .name           = "axp20x-ac-power-supply",
> +               .of_compatible  = "x-powers,axp202-ac-power-supply",
> +               .num_resources  = ARRAY_SIZE(axp192_ac_power_supply_resources),
> +               .resources      = axp192_ac_power_supply_resources,
> +       }, {
> +               .name           = "axp20x-usb-power-supply",
> +               .of_compatible  = "x-powers,axp192-usb-power-supply",
> +               .num_resources  = ARRAY_SIZE(axp192_usb_power_supply_resources),
> +               .resources      = axp192_usb_power_supply_resources,
> +       },
> +       {       .name           = "axp20x-regulator" },
> +};
> +
>  static const struct mfd_cell axp20x_cells[] = {
>         {
>                 .name           = "axp20x-gpio",
> @@ -865,6 +1011,12 @@ int axp20x_match_device(struct axp20x_dev *axp20x)
>                 axp20x->regmap_cfg = &axp152_regmap_config;
>                 axp20x->regmap_irq_chip = &axp152_regmap_irq_chip;
>                 break;
> +       case AXP192_ID:
> +               axp20x->nr_cells = ARRAY_SIZE(axp192_cells);
> +               axp20x->cells = axp192_cells;
> +               axp20x->regmap_cfg = &axp192_regmap_config;
> +               axp20x->regmap_irq_chip = &axp192_regmap_irq_chip;
> +               break;
>         case AXP202_ID:
>         case AXP209_ID:
>                 axp20x->nr_cells = ARRAY_SIZE(axp20x_cells);
> diff --git a/include/linux/mfd/axp20x.h b/include/linux/mfd/axp20x.h
> index 9ab0e2fca7ea..c9a9ee8ec246 100644
> --- a/include/linux/mfd/axp20x.h
> +++ b/include/linux/mfd/axp20x.h
> @@ -12,6 +12,7 @@
>
>  enum axp20x_variants {
>         AXP152_ID = 0,
> +       AXP192_ID,
>         AXP202_ID,
>         AXP209_ID,
>         AXP221_ID,
> @@ -24,6 +25,7 @@ enum axp20x_variants {
>         NR_AXP20X_VARIANTS,
>  };
>
> +#define AXP192_DATACACHE(m)            (0x06 + (m))
>  #define AXP20X_DATACACHE(m)            (0x04 + (m))
>
>  /* Power supply */
> @@ -45,6 +47,13 @@ enum axp20x_variants {
>  #define AXP152_DCDC_FREQ               0x37
>  #define AXP152_DCDC_MODE               0x80
>
> +#define AXP192_USB_OTG_STATUS          0x04
> +#define AXP192_PWR_OUT_CTRL            0x12
> +#define AXP192_DCDC2_V_OUT             0x23
> +#define AXP192_DCDC1_V_OUT             0x26
> +#define AXP192_DCDC3_V_OUT             0x27
> +#define AXP192_LDO2_3_V_OUT            0x28
> +
>  #define AXP20X_PWR_INPUT_STATUS                0x00
>  #define AXP20X_PWR_OP_MODE             0x01
>  #define AXP20X_USB_OTG_STATUS          0x02
> @@ -139,6 +148,17 @@ enum axp20x_variants {
>  #define AXP152_IRQ2_STATE              0x49
>  #define AXP152_IRQ3_STATE              0x4a
>
> +#define AXP192_IRQ1_EN                 0x40
> +#define AXP192_IRQ2_EN                 0x41
> +#define AXP192_IRQ3_EN                 0x42
> +#define AXP192_IRQ4_EN                 0x43
> +#define AXP192_IRQ1_STATE              0x44
> +#define AXP192_IRQ2_STATE              0x45
> +#define AXP192_IRQ3_STATE              0x46
> +#define AXP192_IRQ4_STATE              0x47
> +#define AXP192_IRQ5_EN                 0x4a
> +#define AXP192_IRQ5_STATE              0x4d
> +
>  #define AXP20X_IRQ1_EN                 0x40
>  #define AXP20X_IRQ2_EN                 0x41
>  #define AXP20X_IRQ3_EN                 0x42
> @@ -153,6 +173,11 @@ enum axp20x_variants {
>  #define AXP20X_IRQ6_STATE              0x4d
>
>  /* ADC */
> +#define AXP192_GPIO2_V_ADC_H           0x68
> +#define AXP192_GPIO2_V_ADC_L           0x69
> +#define AXP192_GPIO3_V_ADC_H           0x6a
> +#define AXP192_GPIO3_V_ADC_L           0x6b
> +
>  #define AXP20X_ACIN_V_ADC_H            0x56
>  #define AXP20X_ACIN_V_ADC_L            0x57
>  #define AXP20X_ACIN_I_ADC_H            0x58
> @@ -182,6 +207,8 @@ enum axp20x_variants {
>  #define AXP20X_IPSOUT_V_HIGH_L         0x7f
>
>  /* Power supply */
> +#define AXP192_GPIO30_IN_RANGE         0x85
> +
>  #define AXP20X_DCDC_MODE               0x80
>  #define AXP20X_ADC_EN1                 0x82
>  #define AXP20X_ADC_EN2                 0x83
> @@ -210,6 +237,16 @@ enum axp20x_variants {
>  #define AXP152_PWM1_FREQ_Y             0x9c
>  #define AXP152_PWM1_DUTY_CYCLE         0x9d
>
> +#define AXP192_GPIO0_CTRL              0x90
> +#define AXP192_LDO_IO0_V_OUT           0x91
> +#define AXP192_GPIO1_CTRL              0x92
> +#define AXP192_GPIO2_CTRL              0x93
> +#define AXP192_GPIO2_0_STATE           0x94
> +#define AXP192_GPIO4_3_CTRL            0x95
> +#define AXP192_GPIO4_3_STATE           0x96
> +#define AXP192_GPIO2_0_PULL            0x97
> +#define AXP192_N_RSTO_CTRL             0x9e
> +
>  #define AXP20X_GPIO0_CTRL              0x90
>  #define AXP20X_LDO5_V_OUT              0x91
>  #define AXP20X_GPIO1_CTRL              0x92
> @@ -287,6 +324,17 @@ enum axp20x_variants {
>  #define AXP288_FG_TUNE5             0xed
>
>  /* Regulators IDs */
> +enum {
> +       AXP192_DCDC1 = 0,
> +       AXP192_DCDC2,
> +       AXP192_DCDC3,
> +       AXP192_LDO1,
> +       AXP192_LDO2,
> +       AXP192_LDO3,
> +       AXP192_LDO_IO0,
> +       AXP192_REG_ID_MAX
> +};
> +
>  enum {
>         AXP20X_LDO1 = 0,
>         AXP20X_LDO2,
> @@ -440,6 +488,42 @@ enum {
>         AXP152_IRQ_GPIO0_INPUT,
>  };
>
> +enum axp192_irqs {
> +       AXP192_IRQ_ACIN_OVER_V = 1,
> +       AXP192_IRQ_ACIN_PLUGIN,
> +       AXP192_IRQ_ACIN_REMOVAL,
> +       AXP192_IRQ_VBUS_OVER_V,
> +       AXP192_IRQ_VBUS_PLUGIN,
> +       AXP192_IRQ_VBUS_REMOVAL,
> +       AXP192_IRQ_VBUS_V_LOW,
> +       AXP192_IRQ_BATT_PLUGIN,
> +       AXP192_IRQ_BATT_REMOVAL,
> +       AXP192_IRQ_BATT_ENT_ACT_MODE,
> +       AXP192_IRQ_BATT_EXIT_ACT_MODE,
> +       AXP192_IRQ_CHARG,
> +       AXP192_IRQ_CHARG_DONE,
> +       AXP192_IRQ_BATT_TEMP_HIGH,
> +       AXP192_IRQ_BATT_TEMP_LOW,
> +       AXP192_IRQ_DIE_TEMP_HIGH,
> +       AXP192_IRQ_CHARG_I_LOW,
> +       AXP192_IRQ_DCDC1_V_LONG,
> +       AXP192_IRQ_DCDC2_V_LONG,
> +       AXP192_IRQ_DCDC3_V_LONG,
> +       AXP192_IRQ_PEK_SHORT = 22,
> +       AXP192_IRQ_PEK_LONG,
> +       AXP192_IRQ_N_OE_PWR_ON,
> +       AXP192_IRQ_N_OE_PWR_OFF,
> +       AXP192_IRQ_VBUS_VALID,
> +       AXP192_IRQ_VBUS_NOT_VALID,
> +       AXP192_IRQ_VBUS_SESS_VALID,
> +       AXP192_IRQ_VBUS_SESS_END,
> +       AXP192_IRQ_LOW_PWR_LVL = 31,
> +       AXP192_IRQ_TIMER,
> +       AXP192_IRQ_GPIO2_INPUT = 37,
> +       AXP192_IRQ_GPIO1_INPUT,
> +       AXP192_IRQ_GPIO0_INPUT,
> +};
> +
>  enum {
>         AXP20X_IRQ_ACIN_OVER_V = 1,
>         AXP20X_IRQ_ACIN_PLUGIN,
> --
> 2.35.1
>


--
With Best Regards,
Andy Shevchenko

Re: [PATCH v4 06/15] mfd: axp20x: Add support for AXP192

[Lee Jones]

On Wed, 29 Jun 2022, Aidan MacDonald wrote:

> The AXP192 PMIC is similar to the AXP202/AXP209, but with different
> regulators, additional GPIOs, and a different IRQ register layout.
> 
> Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
> Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
> ---
>  drivers/mfd/axp20x-i2c.c   |   2 +
>  drivers/mfd/axp20x.c       | 152 +++++++++++++++++++++++++++++++++++++
>  include/linux/mfd/axp20x.h |  84 ++++++++++++++++++++
>  3 files changed, 238 insertions(+)
> 
> diff --git a/drivers/mfd/axp20x-i2c.c b/drivers/mfd/axp20x-i2c.c
> index 00ab48018d8d..9ada58fad77f 100644
> --- a/drivers/mfd/axp20x-i2c.c
> +++ b/drivers/mfd/axp20x-i2c.c
> @@ -62,6 +62,7 @@ static int axp20x_i2c_remove(struct i2c_client *i2c)
>  #ifdef CONFIG_OF
>  static const struct of_device_id axp20x_i2c_of_match[] = {
>  	{ .compatible = "x-powers,axp152", .data = (void *)AXP152_ID },
> +	{ .compatible = "x-powers,axp192", .data = (void *)AXP192_ID },
>  	{ .compatible = "x-powers,axp202", .data = (void *)AXP202_ID },
>  	{ .compatible = "x-powers,axp209", .data = (void *)AXP209_ID },
>  	{ .compatible = "x-powers,axp221", .data = (void *)AXP221_ID },
> @@ -75,6 +76,7 @@ MODULE_DEVICE_TABLE(of, axp20x_i2c_of_match);
>  
>  static const struct i2c_device_id axp20x_i2c_id[] = {
>  	{ "axp152", 0 },
> +	{ "axp192", 0 },
>  	{ "axp202", 0 },
>  	{ "axp209", 0 },
>  	{ "axp221", 0 },
> diff --git a/drivers/mfd/axp20x.c b/drivers/mfd/axp20x.c
> index 8161a5dc68e8..6ab2a1f8888c 100644
> --- a/drivers/mfd/axp20x.c
> +++ b/drivers/mfd/axp20x.c
> @@ -34,6 +34,7 @@
>  
>  static const char * const axp20x_model_names[] = {
>  	"AXP152",
> +	"AXP192",
>  	"AXP202",
>  	"AXP209",
>  	"AXP221",
> @@ -92,6 +93,35 @@ static const struct regmap_access_table axp20x_volatile_table = {
>  	.n_yes_ranges	= ARRAY_SIZE(axp20x_volatile_ranges),
>  };
>  
> +static const struct regmap_range axp192_writeable_ranges[] = {
> +	regmap_reg_range(AXP192_DATACACHE(0), AXP192_DATACACHE(5)),
> +	regmap_reg_range(AXP192_PWR_OUT_CTRL, AXP192_IRQ5_STATE),
> +	regmap_reg_range(AXP20X_DCDC_MODE, AXP192_N_RSTO_CTRL),
> +	regmap_reg_range(AXP20X_CC_CTRL, AXP20X_CC_CTRL),
> +};
> +
> +static const struct regmap_range axp192_volatile_ranges[] = {
> +	regmap_reg_range(AXP20X_PWR_INPUT_STATUS, AXP192_USB_OTG_STATUS),
> +	regmap_reg_range(AXP192_IRQ1_STATE, AXP192_IRQ4_STATE),
> +	regmap_reg_range(AXP192_IRQ5_STATE, AXP192_IRQ5_STATE),
> +	regmap_reg_range(AXP20X_ACIN_V_ADC_H, AXP20X_IPSOUT_V_HIGH_L),
> +	regmap_reg_range(AXP20X_TIMER_CTRL, AXP20X_TIMER_CTRL),
> +	regmap_reg_range(AXP192_GPIO2_0_STATE, AXP192_GPIO2_0_STATE),
> +	regmap_reg_range(AXP192_GPIO4_3_STATE, AXP192_GPIO4_3_STATE),
> +	regmap_reg_range(AXP192_N_RSTO_CTRL, AXP192_N_RSTO_CTRL),
> +	regmap_reg_range(AXP20X_CHRG_CC_31_24, AXP20X_CC_CTRL),
> +};
> +
> +static const struct regmap_access_table axp192_writeable_table = {
> +	.yes_ranges	= axp192_writeable_ranges,
> +	.n_yes_ranges	= ARRAY_SIZE(axp192_writeable_ranges),
> +};
> +
> +static const struct regmap_access_table axp192_volatile_table = {
> +	.yes_ranges	= axp192_volatile_ranges,
> +	.n_yes_ranges	= ARRAY_SIZE(axp192_volatile_ranges),
> +};
> +
>  /* AXP22x ranges are shared with the AXP809, as they cover the same range */
>  static const struct regmap_range axp22x_writeable_ranges[] = {
>  	regmap_reg_range(AXP20X_DATACACHE(0), AXP20X_IRQ5_STATE),
> @@ -173,6 +203,25 @@ static const struct resource axp152_pek_resources[] = {
>  	DEFINE_RES_IRQ_NAMED(AXP152_IRQ_PEK_FAL_EDGE, "PEK_DBF"),
>  };
>  
> +static const struct resource axp192_gpio_resources[] = {
> +	DEFINE_RES_IRQ_NAMED(AXP192_IRQ_GPIO0_INPUT, "GPIO0"),
> +	DEFINE_RES_IRQ_NAMED(AXP192_IRQ_GPIO1_INPUT, "GPIO1"),
> +	DEFINE_RES_IRQ_NAMED(AXP192_IRQ_GPIO2_INPUT, "GPIO2"),
> +};
> +
> +static const struct resource axp192_ac_power_supply_resources[] = {
> +	DEFINE_RES_IRQ_NAMED(AXP192_IRQ_ACIN_PLUGIN, "ACIN_PLUGIN"),
> +	DEFINE_RES_IRQ_NAMED(AXP192_IRQ_ACIN_REMOVAL, "ACIN_REMOVAL"),
> +	DEFINE_RES_IRQ_NAMED(AXP192_IRQ_ACIN_OVER_V, "ACIN_OVER_V"),
> +};
> +
> +static const struct resource axp192_usb_power_supply_resources[] = {
> +	DEFINE_RES_IRQ_NAMED(AXP192_IRQ_VBUS_PLUGIN, "VBUS_PLUGIN"),
> +	DEFINE_RES_IRQ_NAMED(AXP192_IRQ_VBUS_REMOVAL, "VBUS_REMOVAL"),
> +	DEFINE_RES_IRQ_NAMED(AXP192_IRQ_VBUS_VALID, "VBUS_VALID"),
> +	DEFINE_RES_IRQ_NAMED(AXP192_IRQ_VBUS_NOT_VALID, "VBUS_NOT_VALID"),
> +};
> +
>  static const struct resource axp20x_ac_power_supply_resources[] = {
>  	DEFINE_RES_IRQ_NAMED(AXP20X_IRQ_ACIN_PLUGIN, "ACIN_PLUGIN"),
>  	DEFINE_RES_IRQ_NAMED(AXP20X_IRQ_ACIN_REMOVAL, "ACIN_REMOVAL"),
> @@ -245,6 +294,15 @@ static const struct regmap_config axp152_regmap_config = {
>  	.cache_type	= REGCACHE_RBTREE,
>  };
>  
> +static const struct regmap_config axp192_regmap_config = {
> +	.reg_bits	= 8,
> +	.val_bits	= 8,
> +	.wr_table	= &axp192_writeable_table,
> +	.volatile_table	= &axp192_volatile_table,
> +	.max_register	= AXP20X_CC_CTRL,
> +	.cache_type	= REGCACHE_RBTREE,
> +};
> +
>  static const struct regmap_config axp20x_regmap_config = {
>  	.reg_bits	= 8,
>  	.val_bits	= 8,
> @@ -304,6 +362,42 @@ static const struct regmap_irq axp152_regmap_irqs[] = {
>  	INIT_REGMAP_IRQ(AXP152, GPIO0_INPUT,		2, 0),
>  };
>  
> +static const struct regmap_irq axp192_regmap_irqs[] = {
> +	INIT_REGMAP_IRQ(AXP192, ACIN_OVER_V,		0, 7),
> +	INIT_REGMAP_IRQ(AXP192, ACIN_PLUGIN,		0, 6),
> +	INIT_REGMAP_IRQ(AXP192, ACIN_REMOVAL,		0, 5),
> +	INIT_REGMAP_IRQ(AXP192, VBUS_OVER_V,		0, 4),
> +	INIT_REGMAP_IRQ(AXP192, VBUS_PLUGIN,		0, 3),
> +	INIT_REGMAP_IRQ(AXP192, VBUS_REMOVAL,		0, 2),
> +	INIT_REGMAP_IRQ(AXP192, VBUS_V_LOW,		0, 1),
> +	INIT_REGMAP_IRQ(AXP192, BATT_PLUGIN,		1, 7),
> +	INIT_REGMAP_IRQ(AXP192, BATT_REMOVAL,	        1, 6),
> +	INIT_REGMAP_IRQ(AXP192, BATT_ENT_ACT_MODE,	1, 5),
> +	INIT_REGMAP_IRQ(AXP192, BATT_EXIT_ACT_MODE,	1, 4),
> +	INIT_REGMAP_IRQ(AXP192, CHARG,		        1, 3),
> +	INIT_REGMAP_IRQ(AXP192, CHARG_DONE,		1, 2),
> +	INIT_REGMAP_IRQ(AXP192, BATT_TEMP_HIGH,	        1, 1),
> +	INIT_REGMAP_IRQ(AXP192, BATT_TEMP_LOW,	        1, 0),
> +	INIT_REGMAP_IRQ(AXP192, DIE_TEMP_HIGH,	        2, 7),
> +	INIT_REGMAP_IRQ(AXP192, CHARG_I_LOW,		2, 6),
> +	INIT_REGMAP_IRQ(AXP192, DCDC1_V_LONG,	        2, 5),
> +	INIT_REGMAP_IRQ(AXP192, DCDC2_V_LONG,	        2, 4),
> +	INIT_REGMAP_IRQ(AXP192, DCDC3_V_LONG,	        2, 3),
> +	INIT_REGMAP_IRQ(AXP192, PEK_SHORT,		2, 1),
> +	INIT_REGMAP_IRQ(AXP192, PEK_LONG,		2, 0),
> +	INIT_REGMAP_IRQ(AXP192, N_OE_PWR_ON,		3, 7),
> +	INIT_REGMAP_IRQ(AXP192, N_OE_PWR_OFF,	        3, 6),
> +	INIT_REGMAP_IRQ(AXP192, VBUS_VALID,		3, 5),
> +	INIT_REGMAP_IRQ(AXP192, VBUS_NOT_VALID,	        3, 4),
> +	INIT_REGMAP_IRQ(AXP192, VBUS_SESS_VALID,	3, 3),
> +	INIT_REGMAP_IRQ(AXP192, VBUS_SESS_END,	        3, 2),
> +	INIT_REGMAP_IRQ(AXP192, LOW_PWR_LVL,	        3, 0),
> +	INIT_REGMAP_IRQ(AXP192, TIMER,			4, 7),
> +	INIT_REGMAP_IRQ(AXP192, GPIO2_INPUT,		4, 2),
> +	INIT_REGMAP_IRQ(AXP192, GPIO1_INPUT,		4, 1),
> +	INIT_REGMAP_IRQ(AXP192, GPIO0_INPUT,		4, 0),
> +};
> +
>  static const struct regmap_irq axp20x_regmap_irqs[] = {
>  	INIT_REGMAP_IRQ(AXP20X, ACIN_OVER_V,		0, 7),
>  	INIT_REGMAP_IRQ(AXP20X, ACIN_PLUGIN,		0, 6),
> @@ -514,6 +608,32 @@ static const struct regmap_irq_chip axp152_regmap_irq_chip = {
>  	.num_regs		= 3,
>  };
>  
> +static unsigned int axp192_get_irq_reg(struct regmap_irq_chip_data *data,
> +				       unsigned int base, int index)
> +{
> +	/* linear mapping for IRQ1 to IRQ4 */
> +	if (index < 4)
> +		return base + index;
> +
> +	/* handle IRQ5 separately */
> +	if (base == AXP192_IRQ1_EN)
> +		return AXP192_IRQ5_EN;
> +
> +	return AXP192_IRQ5_STATE;
> +}
> +
> +static const struct regmap_irq_chip axp192_regmap_irq_chip = {
> +	.name			= "axp192_irq_chip",
> +	.status_base		= AXP192_IRQ1_STATE,
> +	.ack_base		= AXP192_IRQ1_STATE,
> +	.unmask_base		= AXP192_IRQ1_EN,
> +	.init_ack_masked	= true,
> +	.irqs			= axp192_regmap_irqs,
> +	.num_irqs		= ARRAY_SIZE(axp192_regmap_irqs),
> +	.num_regs		= 5,
> +	.get_irq_reg		= axp192_get_irq_reg,

Fix me:

drivers/mfd/axp20x.c:634:35: error: initialization of 'unsigned int (*)(struct regmap_irq_chip_data *, unsigned int,  int)' from incompatible pointer type 'int (*)(unsigned int,  int)' [-Werror=incompatible-pointer-types]
  634 |         .get_irq_reg            = axp192_get_irq_reg,
      |                                   ^~~~~~~~~~~~~~~~~~
drivers/mfd/axp20x.c:634:35: note: (near initialization for 'axp192_regmap_irq_chip.get_irq_reg')

> +};
> +
>  static const struct regmap_irq_chip axp20x_regmap_irq_chip = {
>  	.name			= "axp20x_irq_chip",
>  	.status_base		= AXP20X_IRQ1_STATE,
> @@ -588,6 +708,32 @@ static const struct regmap_irq_chip axp809_regmap_irq_chip = {
>  	.num_regs		= 5,
>  };
>  
> +static const struct mfd_cell axp192_cells[] = {
> +	{
> +		.name		= "axp192-gpio",
> +		.of_compatible	= "x-powers,axp192-gpio",
> +		.num_resources	= ARRAY_SIZE(axp192_gpio_resources),
> +		.resources	= axp192_gpio_resources,
> +	}, {
> +		.name		= "axp192-adc",
> +		.of_compatible	= "x-powers,axp192-adc",
> +	}, {
> +		.name		= "axp20x-battery-power-supply",
> +		.of_compatible	= "x-powers,axp192-battery-power-supply",
> +	}, {
> +		.name		= "axp20x-ac-power-supply",
> +		.of_compatible	= "x-powers,axp202-ac-power-supply",
> +		.num_resources	= ARRAY_SIZE(axp192_ac_power_supply_resources),
> +		.resources	= axp192_ac_power_supply_resources,
> +	}, {
> +		.name		= "axp20x-usb-power-supply",
> +		.of_compatible	= "x-powers,axp192-usb-power-supply",
> +		.num_resources	= ARRAY_SIZE(axp192_usb_power_supply_resources),
> +		.resources	= axp192_usb_power_supply_resources,
> +	},
> +	{	.name		= "axp20x-regulator" },
> +};
> +
>  static const struct mfd_cell axp20x_cells[] = {
>  	{
>  		.name		= "axp20x-gpio",
> @@ -865,6 +1011,12 @@ int axp20x_match_device(struct axp20x_dev *axp20x)
>  		axp20x->regmap_cfg = &axp152_regmap_config;
>  		axp20x->regmap_irq_chip = &axp152_regmap_irq_chip;
>  		break;
> +	case AXP192_ID:
> +		axp20x->nr_cells = ARRAY_SIZE(axp192_cells);
> +		axp20x->cells = axp192_cells;
> +		axp20x->regmap_cfg = &axp192_regmap_config;
> +		axp20x->regmap_irq_chip = &axp192_regmap_irq_chip;
> +		break;
>  	case AXP202_ID:
>  	case AXP209_ID:
>  		axp20x->nr_cells = ARRAY_SIZE(axp20x_cells);
> diff --git a/include/linux/mfd/axp20x.h b/include/linux/mfd/axp20x.h
> index 9ab0e2fca7ea..c9a9ee8ec246 100644
> --- a/include/linux/mfd/axp20x.h
> +++ b/include/linux/mfd/axp20x.h
> @@ -12,6 +12,7 @@
>  
>  enum axp20x_variants {
>  	AXP152_ID = 0,
> +	AXP192_ID,
>  	AXP202_ID,
>  	AXP209_ID,
>  	AXP221_ID,
> @@ -24,6 +25,7 @@ enum axp20x_variants {
>  	NR_AXP20X_VARIANTS,
>  };
>  
> +#define AXP192_DATACACHE(m)		(0x06 + (m))
>  #define AXP20X_DATACACHE(m)		(0x04 + (m))
>  
>  /* Power supply */
> @@ -45,6 +47,13 @@ enum axp20x_variants {
>  #define AXP152_DCDC_FREQ		0x37
>  #define AXP152_DCDC_MODE		0x80
>  
> +#define AXP192_USB_OTG_STATUS		0x04
> +#define AXP192_PWR_OUT_CTRL		0x12
> +#define AXP192_DCDC2_V_OUT		0x23
> +#define AXP192_DCDC1_V_OUT		0x26
> +#define AXP192_DCDC3_V_OUT		0x27
> +#define AXP192_LDO2_3_V_OUT		0x28
> +
>  #define AXP20X_PWR_INPUT_STATUS		0x00
>  #define AXP20X_PWR_OP_MODE		0x01
>  #define AXP20X_USB_OTG_STATUS		0x02
> @@ -139,6 +148,17 @@ enum axp20x_variants {
>  #define AXP152_IRQ2_STATE		0x49
>  #define AXP152_IRQ3_STATE		0x4a
>  
> +#define AXP192_IRQ1_EN			0x40
> +#define AXP192_IRQ2_EN			0x41
> +#define AXP192_IRQ3_EN			0x42
> +#define AXP192_IRQ4_EN			0x43
> +#define AXP192_IRQ1_STATE		0x44
> +#define AXP192_IRQ2_STATE		0x45
> +#define AXP192_IRQ3_STATE		0x46
> +#define AXP192_IRQ4_STATE		0x47
> +#define AXP192_IRQ5_EN			0x4a
> +#define AXP192_IRQ5_STATE		0x4d
> +
>  #define AXP20X_IRQ1_EN			0x40
>  #define AXP20X_IRQ2_EN			0x41
>  #define AXP20X_IRQ3_EN			0x42
> @@ -153,6 +173,11 @@ enum axp20x_variants {
>  #define AXP20X_IRQ6_STATE		0x4d
>  
>  /* ADC */
> +#define AXP192_GPIO2_V_ADC_H		0x68
> +#define AXP192_GPIO2_V_ADC_L		0x69
> +#define AXP192_GPIO3_V_ADC_H		0x6a
> +#define AXP192_GPIO3_V_ADC_L		0x6b
> +
>  #define AXP20X_ACIN_V_ADC_H		0x56
>  #define AXP20X_ACIN_V_ADC_L		0x57
>  #define AXP20X_ACIN_I_ADC_H		0x58
> @@ -182,6 +207,8 @@ enum axp20x_variants {
>  #define AXP20X_IPSOUT_V_HIGH_L		0x7f
>  
>  /* Power supply */
> +#define AXP192_GPIO30_IN_RANGE		0x85
> +
>  #define AXP20X_DCDC_MODE		0x80
>  #define AXP20X_ADC_EN1			0x82
>  #define AXP20X_ADC_EN2			0x83
> @@ -210,6 +237,16 @@ enum axp20x_variants {
>  #define AXP152_PWM1_FREQ_Y		0x9c
>  #define AXP152_PWM1_DUTY_CYCLE		0x9d
>  
> +#define AXP192_GPIO0_CTRL		0x90
> +#define AXP192_LDO_IO0_V_OUT		0x91
> +#define AXP192_GPIO1_CTRL		0x92
> +#define AXP192_GPIO2_CTRL		0x93
> +#define AXP192_GPIO2_0_STATE		0x94
> +#define AXP192_GPIO4_3_CTRL		0x95
> +#define AXP192_GPIO4_3_STATE		0x96
> +#define AXP192_GPIO2_0_PULL		0x97
> +#define AXP192_N_RSTO_CTRL		0x9e
> +
>  #define AXP20X_GPIO0_CTRL		0x90
>  #define AXP20X_LDO5_V_OUT		0x91
>  #define AXP20X_GPIO1_CTRL		0x92
> @@ -287,6 +324,17 @@ enum axp20x_variants {
>  #define AXP288_FG_TUNE5             0xed
>  
>  /* Regulators IDs */
> +enum {
> +	AXP192_DCDC1 = 0,
> +	AXP192_DCDC2,
> +	AXP192_DCDC3,
> +	AXP192_LDO1,
> +	AXP192_LDO2,
> +	AXP192_LDO3,
> +	AXP192_LDO_IO0,
> +	AXP192_REG_ID_MAX
> +};
> +
>  enum {
>  	AXP20X_LDO1 = 0,
>  	AXP20X_LDO2,
> @@ -440,6 +488,42 @@ enum {
>  	AXP152_IRQ_GPIO0_INPUT,
>  };
>  
> +enum axp192_irqs {
> +	AXP192_IRQ_ACIN_OVER_V = 1,
> +	AXP192_IRQ_ACIN_PLUGIN,
> +	AXP192_IRQ_ACIN_REMOVAL,
> +	AXP192_IRQ_VBUS_OVER_V,
> +	AXP192_IRQ_VBUS_PLUGIN,
> +	AXP192_IRQ_VBUS_REMOVAL,
> +	AXP192_IRQ_VBUS_V_LOW,
> +	AXP192_IRQ_BATT_PLUGIN,
> +	AXP192_IRQ_BATT_REMOVAL,
> +	AXP192_IRQ_BATT_ENT_ACT_MODE,
> +	AXP192_IRQ_BATT_EXIT_ACT_MODE,
> +	AXP192_IRQ_CHARG,
> +	AXP192_IRQ_CHARG_DONE,
> +	AXP192_IRQ_BATT_TEMP_HIGH,
> +	AXP192_IRQ_BATT_TEMP_LOW,
> +	AXP192_IRQ_DIE_TEMP_HIGH,
> +	AXP192_IRQ_CHARG_I_LOW,
> +	AXP192_IRQ_DCDC1_V_LONG,
> +	AXP192_IRQ_DCDC2_V_LONG,
> +	AXP192_IRQ_DCDC3_V_LONG,
> +	AXP192_IRQ_PEK_SHORT = 22,
> +	AXP192_IRQ_PEK_LONG,
> +	AXP192_IRQ_N_OE_PWR_ON,
> +	AXP192_IRQ_N_OE_PWR_OFF,
> +	AXP192_IRQ_VBUS_VALID,
> +	AXP192_IRQ_VBUS_NOT_VALID,
> +	AXP192_IRQ_VBUS_SESS_VALID,
> +	AXP192_IRQ_VBUS_SESS_END,
> +	AXP192_IRQ_LOW_PWR_LVL = 31,
> +	AXP192_IRQ_TIMER,
> +	AXP192_IRQ_GPIO2_INPUT = 37,
> +	AXP192_IRQ_GPIO1_INPUT,
> +	AXP192_IRQ_GPIO0_INPUT,
> +};
> +
>  enum {
>  	AXP20X_IRQ_ACIN_OVER_V = 1,
>  	AXP20X_IRQ_ACIN_PLUGIN,

-- 
Lee Jones [李琼斯]
Principal Technical Lead - Developer Services
Linaro.org │ Open source software for Arm SoCs
Follow Linaro: Facebook | Twitter | Blog

Re: [PATCH v4 06/15] mfd: axp20x: Add support for AXP192

[Aidan MacDonald]

Lee Jones <lee.jones@linaro.org> writes:

> On Wed, 29 Jun 2022, Aidan MacDonald wrote:
>
>> The AXP192 PMIC is similar to the AXP202/AXP209, but with different
>> regulators, additional GPIOs, and a different IRQ register layout.
>> 
>> Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
>> Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
>> ---
>>  drivers/mfd/axp20x-i2c.c   |   2 +
>>  drivers/mfd/axp20x.c       | 152 +++++++++++++++++++++++++++++++++++++
>>  include/linux/mfd/axp20x.h |  84 ++++++++++++++++++++
>>  3 files changed, 238 insertions(+)
>> [...]
>> +static const struct regmap_irq_chip axp192_regmap_irq_chip = {
>> +	.name			= "axp192_irq_chip",
>> +	.status_base		= AXP192_IRQ1_STATE,
>> +	.ack_base		= AXP192_IRQ1_STATE,
>> +	.unmask_base		= AXP192_IRQ1_EN,
>> +	.init_ack_masked	= true,
>> +	.irqs			= axp192_regmap_irqs,
>> +	.num_irqs		= ARRAY_SIZE(axp192_regmap_irqs),
>> +	.num_regs		= 5,
>> +	.get_irq_reg		= axp192_get_irq_reg,
>
> Fix me:
>
> drivers/mfd/axp20x.c:634:35: error: initialization of 'unsigned int (*)(struct regmap_irq_chip_data *, unsigned int,  int)' from incompatible pointer type 'int (*)(unsigned int,  int)' [-Werror=incompatible-pointer-types]
>   634 |         .get_irq_reg            = axp192_get_irq_reg,
>       |                                   ^~~~~~~~~~~~~~~~~~
> drivers/mfd/axp20x.c:634:35: note: (near initialization for 'axp192_regmap_irq_chip.get_irq_reg')
>

This doesn't need fixing. You are missing the prerequisite patches.

-- snip --
Changes in v4:
* Drop regmap-irq patches and rebase on top of the regmap-irq
  refactoring series[1], which implements the same functionality.

[1]: https://lore.kernel.org/lkml/20220623211420.918875-1-aidanmacdonald.0x0@gmail.com/
-- snip --

Perhaps I wasn't clear enough that it was a dependency, sorry for
any confusion.

Regards,
Aidan

Re: [PATCH v4 06/15] mfd: axp20x: Add support for AXP192

[Lee Jones]

On Tue, 05 Jul 2022, Aidan MacDonald wrote:

> 
> Lee Jones <lee.jones@linaro.org> writes:
> 
> > On Wed, 29 Jun 2022, Aidan MacDonald wrote:
> >
> >> The AXP192 PMIC is similar to the AXP202/AXP209, but with different
> >> regulators, additional GPIOs, and a different IRQ register layout.
> >> 
> >> Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
> >> Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
> >> ---
> >>  drivers/mfd/axp20x-i2c.c   |   2 +
> >>  drivers/mfd/axp20x.c       | 152 +++++++++++++++++++++++++++++++++++++
> >>  include/linux/mfd/axp20x.h |  84 ++++++++++++++++++++
> >>  3 files changed, 238 insertions(+)
> >> [...]
> >> +static const struct regmap_irq_chip axp192_regmap_irq_chip = {
> >> +	.name			= "axp192_irq_chip",
> >> +	.status_base		= AXP192_IRQ1_STATE,
> >> +	.ack_base		= AXP192_IRQ1_STATE,
> >> +	.unmask_base		= AXP192_IRQ1_EN,
> >> +	.init_ack_masked	= true,
> >> +	.irqs			= axp192_regmap_irqs,
> >> +	.num_irqs		= ARRAY_SIZE(axp192_regmap_irqs),
> >> +	.num_regs		= 5,
> >> +	.get_irq_reg		= axp192_get_irq_reg,
> >
> > Fix me:
> >
> > drivers/mfd/axp20x.c:634:35: error: initialization of 'unsigned int (*)(struct regmap_irq_chip_data *, unsigned int,  int)' from incompatible pointer type 'int (*)(unsigned int,  int)' [-Werror=incompatible-pointer-types]
> >   634 |         .get_irq_reg            = axp192_get_irq_reg,
> >       |                                   ^~~~~~~~~~~~~~~~~~
> > drivers/mfd/axp20x.c:634:35: note: (near initialization for 'axp192_regmap_irq_chip.get_irq_reg')
> >
> 
> This doesn't need fixing. You are missing the prerequisite patches.
> 
> -- snip --
> Changes in v4:
> * Drop regmap-irq patches and rebase on top of the regmap-irq
>   refactoring series[1], which implements the same functionality.
> 
> [1]: https://lore.kernel.org/lkml/20220623211420.918875-1-aidanmacdonald.0x0@gmail.com/
> -- snip --

> Perhaps I wasn't clear enough that it was a dependency, sorry for
> any confusion.

Any idea why the regmap-irq patches weren't in -next?

-- 
Lee Jones [李琼斯]
Principal Technical Lead - Developer Services
Linaro.org │ Open source software for Arm SoCs
Follow Linaro: Facebook | Twitter | Blog

Re: [PATCH v4 06/15] mfd: axp20x: Add support for AXP192

[Aidan MacDonald]

Lee Jones <lee.jones@linaro.org> writes:

> On Tue, 05 Jul 2022, Aidan MacDonald wrote:
>
>> 
>> Lee Jones <lee.jones@linaro.org> writes:
>> 
>> > On Wed, 29 Jun 2022, Aidan MacDonald wrote:
>> >
>> >> The AXP192 PMIC is similar to the AXP202/AXP209, but with different
>> >> regulators, additional GPIOs, and a different IRQ register layout.
>> >> 
>> >> Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
>> >> Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
>> >> ---
>> >>  drivers/mfd/axp20x-i2c.c   |   2 +
>> >>  drivers/mfd/axp20x.c       | 152 +++++++++++++++++++++++++++++++++++++
>> >>  include/linux/mfd/axp20x.h |  84 ++++++++++++++++++++
>> >>  3 files changed, 238 insertions(+)
>> >> [...]
>> >> +static const struct regmap_irq_chip axp192_regmap_irq_chip = {
>> >> +	.name			= "axp192_irq_chip",
>> >> +	.status_base		= AXP192_IRQ1_STATE,
>> >> +	.ack_base		= AXP192_IRQ1_STATE,
>> >> +	.unmask_base		= AXP192_IRQ1_EN,
>> >> +	.init_ack_masked	= true,
>> >> +	.irqs			= axp192_regmap_irqs,
>> >> +	.num_irqs		= ARRAY_SIZE(axp192_regmap_irqs),
>> >> +	.num_regs		= 5,
>> >> +	.get_irq_reg		= axp192_get_irq_reg,
>> >
>> > Fix me:
>> >
>> > drivers/mfd/axp20x.c:634:35: error: initialization of 'unsigned int (*)(struct regmap_irq_chip_data *, unsigned int,  int)' from incompatible pointer type 'int (*)(unsigned int,  int)' [-Werror=incompatible-pointer-types]
>> >   634 |         .get_irq_reg            = axp192_get_irq_reg,
>> >       |                                   ^~~~~~~~~~~~~~~~~~
>> > drivers/mfd/axp20x.c:634:35: note: (near initialization for 'axp192_regmap_irq_chip.get_irq_reg')
>> >
>> 
>> This doesn't need fixing. You are missing the prerequisite patches.
>> 
>> -- snip --
>> Changes in v4:
>> * Drop regmap-irq patches and rebase on top of the regmap-irq
>>   refactoring series[1], which implements the same functionality.
>> 
>> [1]: https://lore.kernel.org/lkml/20220623211420.918875-1-aidanmacdonald.0x0@gmail.com/
>> -- snip --
>
>> Perhaps I wasn't clear enough that it was a dependency, sorry for
>> any confusion.
>
> Any idea why the regmap-irq patches weren't in -next?

Uh, sorry, I didn't pay attention and assumed this was the same error
the kernel test robot was reporting against mfd-next (missing field).
But the field does exist; this error is a type mismatch:

  initialization of 'unsigned int (*)(struct regmap_irq_chip_data *,
                                      unsigned int,  int)'
  from incompatible pointer type 'int (*)(unsigned int,  int)'

So the regmap-irq patches were in -next, the problem is you were
using the old patch from v3.

FYI, I just sent a v5 which drops the GPIO driver, so please use
the patches from that version. Thanks.

Regards,
Aidan

[PATCH v4 07/15] regulator: axp20x: Add support for AXP192

[Aidan MacDonald]

Add support for the AXP192 PMIC.

Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
---
 drivers/regulator/axp20x-regulator.c | 100 ++++++++++++++++++++++++---
 1 file changed, 91 insertions(+), 9 deletions(-)

diff --git a/drivers/regulator/axp20x-regulator.c b/drivers/regulator/axp20x-regulator.c
index d260c442b788..ee79a9ed0249 100644
--- a/drivers/regulator/axp20x-regulator.c
+++ b/drivers/regulator/axp20x-regulator.c
@@ -27,6 +27,29 @@
 #include <linux/regulator/machine.h>
 #include <linux/regulator/of_regulator.h>
 
+#define AXP192_GPIO0_FUNC_MASK		GENMASK(2, 0)
+
+#define AXP192_IO_ENABLED		0x02
+#define AXP192_IO_DISABLED		0x06
+
+#define AXP192_WORKMODE_DCDC1_MASK	BIT_MASK(3)
+#define AXP192_WORKMODE_DCDC2_MASK	BIT_MASK(2)
+#define AXP192_WORKMODE_DCDC3_MASK	BIT_MASK(1)
+
+#define AXP192_DCDC1_V_OUT_MASK		GENMASK(6, 0)
+#define AXP192_DCDC2_V_OUT_MASK		GENMASK(5, 0)
+#define AXP192_DCDC3_V_OUT_MASK		GENMASK(6, 0)
+#define AXP192_LDO2_V_OUT_MASK		GENMASK(7, 4)
+#define AXP192_LDO3_V_OUT_MASK		GENMASK(3, 0)
+#define AXP192_LDO_IO0_V_OUT_MASK	GENMASK(7, 4)
+
+#define AXP192_PWR_OUT_EXTEN_MASK	BIT_MASK(6)
+#define AXP192_PWR_OUT_DCDC2_MASK	BIT_MASK(4)
+#define AXP192_PWR_OUT_LDO3_MASK	BIT_MASK(3)
+#define AXP192_PWR_OUT_LDO2_MASK	BIT_MASK(2)
+#define AXP192_PWR_OUT_DCDC3_MASK	BIT_MASK(1)
+#define AXP192_PWR_OUT_DCDC1_MASK	BIT_MASK(0)
+
 #define AXP20X_GPIO0_FUNC_MASK		GENMASK(3, 0)
 #define AXP20X_GPIO1_FUNC_MASK		GENMASK(3, 0)
 
@@ -375,25 +398,32 @@ static int axp20x_set_ramp_delay(struct regulator_dev *rdev, int ramp)
 
 	switch (axp20x->variant) {
 	case AXP209_ID:
-		if (id == AXP20X_DCDC2) {
+		if (id == AXP20X_LDO3) {
 			slew_rates = axp209_dcdc2_ldo3_slew_rates;
 			rate_count = ARRAY_SIZE(axp209_dcdc2_ldo3_slew_rates);
 			reg = AXP20X_DCDC2_LDO3_V_RAMP;
-			mask = AXP20X_DCDC2_LDO3_V_RAMP_DCDC2_RATE_MASK |
-			       AXP20X_DCDC2_LDO3_V_RAMP_DCDC2_EN_MASK;
+			mask = AXP20X_DCDC2_LDO3_V_RAMP_LDO3_RATE_MASK |
+			       AXP20X_DCDC2_LDO3_V_RAMP_LDO3_EN_MASK;
 			enable = (ramp > 0) ?
-				 AXP20X_DCDC2_LDO3_V_RAMP_DCDC2_EN : 0;
+				 AXP20X_DCDC2_LDO3_V_RAMP_LDO3_EN : 0;
 			break;
 		}
 
-		if (id == AXP20X_LDO3) {
+		fallthrough;
+
+	case AXP192_ID:
+		/*
+		 * AXP192 and AXP209 share the same DCDC2 ramp configuration
+		 */
+		if ((axp20x->variant == AXP209_ID && id == AXP20X_DCDC2) ||
+		    (axp20x->variant == AXP192_ID && id == AXP192_DCDC2)) {
 			slew_rates = axp209_dcdc2_ldo3_slew_rates;
 			rate_count = ARRAY_SIZE(axp209_dcdc2_ldo3_slew_rates);
 			reg = AXP20X_DCDC2_LDO3_V_RAMP;
-			mask = AXP20X_DCDC2_LDO3_V_RAMP_LDO3_RATE_MASK |
-			       AXP20X_DCDC2_LDO3_V_RAMP_LDO3_EN_MASK;
+			mask = AXP20X_DCDC2_LDO3_V_RAMP_DCDC2_RATE_MASK |
+			       AXP20X_DCDC2_LDO3_V_RAMP_DCDC2_EN_MASK;
 			enable = (ramp > 0) ?
-				 AXP20X_DCDC2_LDO3_V_RAMP_LDO3_EN : 0;
+				 AXP20X_DCDC2_LDO3_V_RAMP_DCDC2_EN : 0;
 			break;
 		}
 
@@ -415,7 +445,8 @@ static int axp20x_set_ramp_delay(struct regulator_dev *rdev, int ramp)
 			if (ramp > slew_rates[i])
 				break;
 
-			if (id == AXP20X_DCDC2)
+			if ((axp20x->variant == AXP209_ID && id == AXP20X_DCDC2) ||
+			    (axp20x->variant == AXP192_ID && id == AXP192_DCDC2))
 				cfg = AXP20X_DCDC2_LDO3_V_RAMP_DCDC2_RATE(i);
 			else
 				cfg = AXP20X_DCDC2_LDO3_V_RAMP_LDO3_RATE(i);
@@ -511,6 +542,29 @@ static const struct regulator_ops axp20x_ops_sw = {
 	.is_enabled		= regulator_is_enabled_regmap,
 };
 
+static const struct regulator_desc axp192_regulators[] = {
+	AXP_DESC(AXP192, DCDC1, "dcdc1", "vin1", 700, 3500, 25,
+		 AXP192_DCDC1_V_OUT, AXP192_DCDC1_V_OUT_MASK,
+		 AXP192_PWR_OUT_CTRL, AXP192_PWR_OUT_DCDC1_MASK),
+	AXP_DESC(AXP192, DCDC2, "dcdc2", "vin2", 700, 2275, 25,
+		 AXP192_DCDC2_V_OUT, AXP192_DCDC2_V_OUT_MASK,
+		 AXP192_PWR_OUT_CTRL, AXP192_PWR_OUT_DCDC2_MASK),
+	AXP_DESC(AXP192, DCDC3, "dcdc3", "vin3", 700, 3500, 25,
+		 AXP192_DCDC3_V_OUT, AXP192_DCDC3_V_OUT_MASK,
+		 AXP192_PWR_OUT_CTRL, AXP192_PWR_OUT_DCDC3_MASK),
+	AXP_DESC_FIXED(AXP192, LDO1, "ldo1", "acin", 1250),
+	AXP_DESC(AXP192, LDO2, "ldo2", "ldoin", 1800, 3300, 100,
+		 AXP192_LDO2_3_V_OUT, AXP192_LDO2_V_OUT_MASK,
+		 AXP192_PWR_OUT_CTRL, AXP192_PWR_OUT_LDO2_MASK),
+	AXP_DESC(AXP192, LDO3, "ldo3", "ldoin", 1800, 3300, 100,
+		 AXP192_LDO2_3_V_OUT, AXP192_LDO3_V_OUT_MASK,
+		 AXP192_PWR_OUT_CTRL, AXP192_PWR_OUT_LDO3_MASK),
+	AXP_DESC_IO(AXP192, LDO_IO0, "ldo_io0", "ips", 700, 3300, 100,
+		    AXP192_LDO_IO0_V_OUT, AXP192_LDO_IO0_V_OUT_MASK,
+		    AXP192_GPIO0_CTRL, AXP192_GPIO0_FUNC_MASK,
+		    AXP192_IO_ENABLED, AXP192_IO_DISABLED),
+};
+
 static const struct linear_range axp20x_ldo4_ranges[] = {
 	REGULATOR_LINEAR_RANGE(1250000,
 			       AXP20X_LDO4_V_OUT_1250mV_START,
@@ -1008,6 +1062,12 @@ static int axp20x_set_dcdc_freq(struct platform_device *pdev, u32 dcdcfreq)
 	u32 min, max, def, step;
 
 	switch (axp20x->variant) {
+	case AXP192_ID:
+		min = 900;
+		max = 2025;
+		def = 1500;
+		step = 75;
+		break;
 	case AXP202_ID:
 	case AXP209_ID:
 		min = 750;
@@ -1100,6 +1160,24 @@ static int axp20x_set_dcdc_workmode(struct regulator_dev *rdev, int id, u32 work
 	unsigned int mask;
 
 	switch (axp20x->variant) {
+	case AXP192_ID:
+		switch (id) {
+		case AXP192_DCDC1:
+			mask = AXP192_WORKMODE_DCDC1_MASK;
+			break;
+		case AXP192_DCDC2:
+			mask = AXP192_WORKMODE_DCDC2_MASK;
+			break;
+		case AXP192_DCDC3:
+			mask = AXP192_WORKMODE_DCDC3_MASK;
+			break;
+		default:
+			return -EINVAL;
+		}
+
+		workmode <<= ffs(mask) - 1;
+		break;
+
 	case AXP202_ID:
 	case AXP209_ID:
 		if ((id != AXP20X_DCDC2) && (id != AXP20X_DCDC3))
@@ -1220,6 +1298,10 @@ static int axp20x_regulator_probe(struct platform_device *pdev)
 	bool drivevbus = false;
 
 	switch (axp20x->variant) {
+	case AXP192_ID:
+		regulators = axp192_regulators;
+		nregulators = AXP192_REG_ID_MAX;
+		break;
 	case AXP202_ID:
 	case AXP209_ID:
 		regulators = axp20x_regulators;
-- 
2.35.1

Re: [PATCH v4 07/15] regulator: axp20x: Add support for AXP192

[Andy Shevchenko]

On Wed, Jun 29, 2022 at 4:29 PM Aidan MacDonald
<aidanmacdonald.0x0@gmail.com> wrote:
>
> Add support for the AXP192 PMIC.

Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>

> Acked-by: Mark Brown <broonie@kernel.org>
> Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
> ---
>  drivers/regulator/axp20x-regulator.c | 100 ++++++++++++++++++++++++---
>  1 file changed, 91 insertions(+), 9 deletions(-)
>
> diff --git a/drivers/regulator/axp20x-regulator.c b/drivers/regulator/axp20x-regulator.c
> index d260c442b788..ee79a9ed0249 100644
> --- a/drivers/regulator/axp20x-regulator.c
> +++ b/drivers/regulator/axp20x-regulator.c
> @@ -27,6 +27,29 @@
>  #include <linux/regulator/machine.h>
>  #include <linux/regulator/of_regulator.h>
>
> +#define AXP192_GPIO0_FUNC_MASK         GENMASK(2, 0)
> +
> +#define AXP192_IO_ENABLED              0x02
> +#define AXP192_IO_DISABLED             0x06
> +
> +#define AXP192_WORKMODE_DCDC1_MASK     BIT_MASK(3)
> +#define AXP192_WORKMODE_DCDC2_MASK     BIT_MASK(2)
> +#define AXP192_WORKMODE_DCDC3_MASK     BIT_MASK(1)
> +
> +#define AXP192_DCDC1_V_OUT_MASK                GENMASK(6, 0)
> +#define AXP192_DCDC2_V_OUT_MASK                GENMASK(5, 0)
> +#define AXP192_DCDC3_V_OUT_MASK                GENMASK(6, 0)
> +#define AXP192_LDO2_V_OUT_MASK         GENMASK(7, 4)
> +#define AXP192_LDO3_V_OUT_MASK         GENMASK(3, 0)
> +#define AXP192_LDO_IO0_V_OUT_MASK      GENMASK(7, 4)
> +
> +#define AXP192_PWR_OUT_EXTEN_MASK      BIT_MASK(6)
> +#define AXP192_PWR_OUT_DCDC2_MASK      BIT_MASK(4)
> +#define AXP192_PWR_OUT_LDO3_MASK       BIT_MASK(3)
> +#define AXP192_PWR_OUT_LDO2_MASK       BIT_MASK(2)
> +#define AXP192_PWR_OUT_DCDC3_MASK      BIT_MASK(1)
> +#define AXP192_PWR_OUT_DCDC1_MASK      BIT_MASK(0)
> +
>  #define AXP20X_GPIO0_FUNC_MASK         GENMASK(3, 0)
>  #define AXP20X_GPIO1_FUNC_MASK         GENMASK(3, 0)
>
> @@ -375,25 +398,32 @@ static int axp20x_set_ramp_delay(struct regulator_dev *rdev, int ramp)
>
>         switch (axp20x->variant) {
>         case AXP209_ID:
> -               if (id == AXP20X_DCDC2) {
> +               if (id == AXP20X_LDO3) {
>                         slew_rates = axp209_dcdc2_ldo3_slew_rates;
>                         rate_count = ARRAY_SIZE(axp209_dcdc2_ldo3_slew_rates);
>                         reg = AXP20X_DCDC2_LDO3_V_RAMP;
> -                       mask = AXP20X_DCDC2_LDO3_V_RAMP_DCDC2_RATE_MASK |
> -                              AXP20X_DCDC2_LDO3_V_RAMP_DCDC2_EN_MASK;
> +                       mask = AXP20X_DCDC2_LDO3_V_RAMP_LDO3_RATE_MASK |
> +                              AXP20X_DCDC2_LDO3_V_RAMP_LDO3_EN_MASK;
>                         enable = (ramp > 0) ?
> -                                AXP20X_DCDC2_LDO3_V_RAMP_DCDC2_EN : 0;
> +                                AXP20X_DCDC2_LDO3_V_RAMP_LDO3_EN : 0;
>                         break;
>                 }
>
> -               if (id == AXP20X_LDO3) {
> +               fallthrough;
> +
> +       case AXP192_ID:
> +               /*
> +                * AXP192 and AXP209 share the same DCDC2 ramp configuration
> +                */
> +               if ((axp20x->variant == AXP209_ID && id == AXP20X_DCDC2) ||
> +                   (axp20x->variant == AXP192_ID && id == AXP192_DCDC2)) {
>                         slew_rates = axp209_dcdc2_ldo3_slew_rates;
>                         rate_count = ARRAY_SIZE(axp209_dcdc2_ldo3_slew_rates);
>                         reg = AXP20X_DCDC2_LDO3_V_RAMP;
> -                       mask = AXP20X_DCDC2_LDO3_V_RAMP_LDO3_RATE_MASK |
> -                              AXP20X_DCDC2_LDO3_V_RAMP_LDO3_EN_MASK;
> +                       mask = AXP20X_DCDC2_LDO3_V_RAMP_DCDC2_RATE_MASK |
> +                              AXP20X_DCDC2_LDO3_V_RAMP_DCDC2_EN_MASK;
>                         enable = (ramp > 0) ?
> -                                AXP20X_DCDC2_LDO3_V_RAMP_LDO3_EN : 0;
> +                                AXP20X_DCDC2_LDO3_V_RAMP_DCDC2_EN : 0;
>                         break;
>                 }
>
> @@ -415,7 +445,8 @@ static int axp20x_set_ramp_delay(struct regulator_dev *rdev, int ramp)
>                         if (ramp > slew_rates[i])
>                                 break;
>
> -                       if (id == AXP20X_DCDC2)
> +                       if ((axp20x->variant == AXP209_ID && id == AXP20X_DCDC2) ||
> +                           (axp20x->variant == AXP192_ID && id == AXP192_DCDC2))
>                                 cfg = AXP20X_DCDC2_LDO3_V_RAMP_DCDC2_RATE(i);
>                         else
>                                 cfg = AXP20X_DCDC2_LDO3_V_RAMP_LDO3_RATE(i);
> @@ -511,6 +542,29 @@ static const struct regulator_ops axp20x_ops_sw = {
>         .is_enabled             = regulator_is_enabled_regmap,
>  };
>
> +static const struct regulator_desc axp192_regulators[] = {
> +       AXP_DESC(AXP192, DCDC1, "dcdc1", "vin1", 700, 3500, 25,
> +                AXP192_DCDC1_V_OUT, AXP192_DCDC1_V_OUT_MASK,
> +                AXP192_PWR_OUT_CTRL, AXP192_PWR_OUT_DCDC1_MASK),
> +       AXP_DESC(AXP192, DCDC2, "dcdc2", "vin2", 700, 2275, 25,
> +                AXP192_DCDC2_V_OUT, AXP192_DCDC2_V_OUT_MASK,
> +                AXP192_PWR_OUT_CTRL, AXP192_PWR_OUT_DCDC2_MASK),
> +       AXP_DESC(AXP192, DCDC3, "dcdc3", "vin3", 700, 3500, 25,
> +                AXP192_DCDC3_V_OUT, AXP192_DCDC3_V_OUT_MASK,
> +                AXP192_PWR_OUT_CTRL, AXP192_PWR_OUT_DCDC3_MASK),
> +       AXP_DESC_FIXED(AXP192, LDO1, "ldo1", "acin", 1250),
> +       AXP_DESC(AXP192, LDO2, "ldo2", "ldoin", 1800, 3300, 100,
> +                AXP192_LDO2_3_V_OUT, AXP192_LDO2_V_OUT_MASK,
> +                AXP192_PWR_OUT_CTRL, AXP192_PWR_OUT_LDO2_MASK),
> +       AXP_DESC(AXP192, LDO3, "ldo3", "ldoin", 1800, 3300, 100,
> +                AXP192_LDO2_3_V_OUT, AXP192_LDO3_V_OUT_MASK,
> +                AXP192_PWR_OUT_CTRL, AXP192_PWR_OUT_LDO3_MASK),
> +       AXP_DESC_IO(AXP192, LDO_IO0, "ldo_io0", "ips", 700, 3300, 100,
> +                   AXP192_LDO_IO0_V_OUT, AXP192_LDO_IO0_V_OUT_MASK,
> +                   AXP192_GPIO0_CTRL, AXP192_GPIO0_FUNC_MASK,
> +                   AXP192_IO_ENABLED, AXP192_IO_DISABLED),
> +};
> +
>  static const struct linear_range axp20x_ldo4_ranges[] = {
>         REGULATOR_LINEAR_RANGE(1250000,
>                                AXP20X_LDO4_V_OUT_1250mV_START,
> @@ -1008,6 +1062,12 @@ static int axp20x_set_dcdc_freq(struct platform_device *pdev, u32 dcdcfreq)
>         u32 min, max, def, step;
>
>         switch (axp20x->variant) {
> +       case AXP192_ID:
> +               min = 900;
> +               max = 2025;
> +               def = 1500;
> +               step = 75;
> +               break;
>         case AXP202_ID:
>         case AXP209_ID:
>                 min = 750;
> @@ -1100,6 +1160,24 @@ static int axp20x_set_dcdc_workmode(struct regulator_dev *rdev, int id, u32 work
>         unsigned int mask;
>
>         switch (axp20x->variant) {
> +       case AXP192_ID:
> +               switch (id) {
> +               case AXP192_DCDC1:
> +                       mask = AXP192_WORKMODE_DCDC1_MASK;
> +                       break;
> +               case AXP192_DCDC2:
> +                       mask = AXP192_WORKMODE_DCDC2_MASK;
> +                       break;
> +               case AXP192_DCDC3:
> +                       mask = AXP192_WORKMODE_DCDC3_MASK;
> +                       break;
> +               default:
> +                       return -EINVAL;
> +               }
> +
> +               workmode <<= ffs(mask) - 1;
> +               break;
> +
>         case AXP202_ID:
>         case AXP209_ID:
>                 if ((id != AXP20X_DCDC2) && (id != AXP20X_DCDC3))
> @@ -1220,6 +1298,10 @@ static int axp20x_regulator_probe(struct platform_device *pdev)
>         bool drivevbus = false;
>
>         switch (axp20x->variant) {
> +       case AXP192_ID:
> +               regulators = axp192_regulators;
> +               nregulators = AXP192_REG_ID_MAX;
> +               break;
>         case AXP202_ID:
>         case AXP209_ID:
>                 regulators = axp20x_regulators;
> --
> 2.35.1
>


-- 
With Best Regards,
Andy Shevchenko

[PATCH v4 08/15] iio: adc: axp20x_adc: Minor code cleanups

[Aidan MacDonald]

The code may be clearer if parameters are not re-purposed to hold
temporary results like register values, so introduce local variables
as necessary to avoid that. Regroup macros based on chip type, and
use the FIELD_PREP() macro instead of a hand-rolled version.

Suggested-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
---
 drivers/iio/adc/axp20x_adc.c | 61 +++++++++++++++++++-----------------
 1 file changed, 32 insertions(+), 29 deletions(-)

diff --git a/drivers/iio/adc/axp20x_adc.c b/drivers/iio/adc/axp20x_adc.c
index 53bf7d4899d2..ab25e6e1ff65 100644
--- a/drivers/iio/adc/axp20x_adc.c
+++ b/drivers/iio/adc/axp20x_adc.c
@@ -5,6 +5,7 @@
  *	Quentin Schulz <quentin.schulz@free-electrons.com>
  */
 
+#include <linux/bitfield.h>
 #include <linux/completion.h>
 #include <linux/interrupt.h>
 #include <linux/io.h>
@@ -22,20 +23,20 @@
 #include <linux/mfd/axp20x.h>
 
 #define AXP20X_ADC_EN1_MASK			GENMASK(7, 0)
-
 #define AXP20X_ADC_EN2_MASK			(GENMASK(3, 2) | BIT(7))
+
 #define AXP22X_ADC_EN1_MASK			(GENMASK(7, 5) | BIT(0))
 
 #define AXP20X_GPIO10_IN_RANGE_GPIO0		BIT(0)
 #define AXP20X_GPIO10_IN_RANGE_GPIO1		BIT(1)
-#define AXP20X_GPIO10_IN_RANGE_GPIO0_VAL(x)	((x) & BIT(0))
-#define AXP20X_GPIO10_IN_RANGE_GPIO1_VAL(x)	(((x) & BIT(0)) << 1)
 
 #define AXP20X_ADC_RATE_MASK			GENMASK(7, 6)
-#define AXP813_V_I_ADC_RATE_MASK		GENMASK(5, 4)
-#define AXP813_ADC_RATE_MASK			(AXP20X_ADC_RATE_MASK | AXP813_V_I_ADC_RATE_MASK)
 #define AXP20X_ADC_RATE_HZ(x)			((ilog2((x) / 25) << 6) & AXP20X_ADC_RATE_MASK)
+
 #define AXP22X_ADC_RATE_HZ(x)			((ilog2((x) / 100) << 6) & AXP20X_ADC_RATE_MASK)
+
+#define AXP813_V_I_ADC_RATE_MASK		GENMASK(5, 4)
+#define AXP813_ADC_RATE_MASK			(AXP20X_ADC_RATE_MASK | AXP813_V_I_ADC_RATE_MASK)
 #define AXP813_TS_GPIO0_ADC_RATE_HZ(x)		AXP20X_ADC_RATE_HZ(x)
 #define AXP813_V_I_ADC_RATE_HZ(x)		((ilog2((x) / 100) << 4) & AXP813_V_I_ADC_RATE_MASK)
 #define AXP813_ADC_RATE_HZ(x)			(AXP20X_ADC_RATE_HZ(x) | AXP813_V_I_ADC_RATE_HZ(x))
@@ -234,7 +235,7 @@ static int axp20x_adc_raw(struct iio_dev *indio_dev,
 			  struct iio_chan_spec const *chan, int *val)
 {
 	struct axp20x_adc_iio *info = iio_priv(indio_dev);
-	int size = 12;
+	int ret, size;
 
 	/*
 	 * N.B.:  Unlike the Chinese datasheets tell, the charging current is
@@ -246,10 +247,11 @@ static int axp20x_adc_raw(struct iio_dev *indio_dev,
 	else
 		size = 12;
 
-	*val = axp20x_read_variable_width(info->regmap, chan->address, size);
-	if (*val < 0)
-		return *val;
+	ret = axp20x_read_variable_width(info->regmap, chan->address, size);
+	if (ret < 0)
+		return ret;
 
+	*val = ret;
 	return IIO_VAL_INT;
 }
 
@@ -257,11 +259,13 @@ static int axp22x_adc_raw(struct iio_dev *indio_dev,
 			  struct iio_chan_spec const *chan, int *val)
 {
 	struct axp20x_adc_iio *info = iio_priv(indio_dev);
+	int ret;
 
-	*val = axp20x_read_variable_width(info->regmap, chan->address, 12);
-	if (*val < 0)
-		return *val;
+	ret = axp20x_read_variable_width(info->regmap, chan->address, 12);
+	if (ret < 0)
+		return ret;
 
+	*val = ret;
 	return IIO_VAL_INT;
 }
 
@@ -269,11 +273,13 @@ static int axp813_adc_raw(struct iio_dev *indio_dev,
 			  struct iio_chan_spec const *chan, int *val)
 {
 	struct axp20x_adc_iio *info = iio_priv(indio_dev);
+	int ret;
 
-	*val = axp20x_read_variable_width(info->regmap, chan->address, 12);
-	if (*val < 0)
-		return *val;
+	ret = axp20x_read_variable_width(info->regmap, chan->address, 12);
+	if (ret < 0)
+		return ret;
 
+	*val = ret;
 	return IIO_VAL_INT;
 }
 
@@ -443,27 +449,27 @@ static int axp20x_adc_offset_voltage(struct iio_dev *indio_dev, int channel,
 				     int *val)
 {
 	struct axp20x_adc_iio *info = iio_priv(indio_dev);
+	unsigned int regval;
 	int ret;
 
-	ret = regmap_read(info->regmap, AXP20X_GPIO10_IN_RANGE, val);
+	ret = regmap_read(info->regmap, AXP20X_GPIO10_IN_RANGE, &regval);
 	if (ret < 0)
 		return ret;
 
 	switch (channel) {
 	case AXP20X_GPIO0_V:
-		*val &= AXP20X_GPIO10_IN_RANGE_GPIO0;
+		regval = FIELD_GET(AXP20X_GPIO10_IN_RANGE_GPIO0, regval);
 		break;
 
 	case AXP20X_GPIO1_V:
-		*val &= AXP20X_GPIO10_IN_RANGE_GPIO1;
+		regval = FIELD_GET(AXP20X_GPIO10_IN_RANGE_GPIO1, regval);
 		break;
 
 	default:
 		return -EINVAL;
 	}
 
-	*val = *val ? 700000 : 0;
-
+	*val = regval ? 700000 : 0;
 	return IIO_VAL_INT;
 }
 
@@ -548,7 +554,7 @@ static int axp20x_write_raw(struct iio_dev *indio_dev,
 			    long mask)
 {
 	struct axp20x_adc_iio *info = iio_priv(indio_dev);
-	unsigned int reg, regval;
+	unsigned int regmask, regval;
 
 	/*
 	 * The AXP20X PMIC allows the user to choose between 0V and 0.7V offsets
@@ -560,25 +566,22 @@ static int axp20x_write_raw(struct iio_dev *indio_dev,
 	if (val != 0 && val != 700000)
 		return -EINVAL;
 
-	val = val ? 1 : 0;
-
 	switch (chan->channel) {
 	case AXP20X_GPIO0_V:
-		reg = AXP20X_GPIO10_IN_RANGE_GPIO0;
-		regval = AXP20X_GPIO10_IN_RANGE_GPIO0_VAL(val);
+		regmask = AXP20X_GPIO10_IN_RANGE_GPIO0;
+		regval = FIELD_PREP(AXP20X_GPIO10_IN_RANGE_GPIO0, !!val);
 		break;
 
 	case AXP20X_GPIO1_V:
-		reg = AXP20X_GPIO10_IN_RANGE_GPIO1;
-		regval = AXP20X_GPIO10_IN_RANGE_GPIO1_VAL(val);
+		regmask = AXP20X_GPIO10_IN_RANGE_GPIO1;
+		regval = FIELD_PREP(AXP20X_GPIO10_IN_RANGE_GPIO1, !!val);
 		break;
 
 	default:
 		return -EINVAL;
 	}
 
-	return regmap_update_bits(info->regmap, AXP20X_GPIO10_IN_RANGE, reg,
-				  regval);
+	return regmap_update_bits(info->regmap, AXP20X_GPIO10_IN_RANGE, regmask, regval);
 }
 
 static const struct iio_info axp20x_adc_iio_info = {
-- 
2.35.1

Re: [PATCH v4 08/15] iio: adc: axp20x_adc: Minor code cleanups

[Andy Shevchenko]

On Wed, Jun 29, 2022 at 4:30 PM Aidan MacDonald
<aidanmacdonald.0x0@gmail.com> wrote:
>
> The code may be clearer if parameters are not re-purposed to hold
> temporary results like register values, so introduce local variables
> as necessary to avoid that. Regroup macros based on chip type, and
> use the FIELD_PREP() macro instead of a hand-rolled version.

Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>

> Suggested-by: Jonathan Cameron <jic23@kernel.org>
> Reviewed-by: Chen-Yu Tsai <wens@csie.org>
> Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
> Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
> ---
>  drivers/iio/adc/axp20x_adc.c | 61 +++++++++++++++++++-----------------
>  1 file changed, 32 insertions(+), 29 deletions(-)
>
> diff --git a/drivers/iio/adc/axp20x_adc.c b/drivers/iio/adc/axp20x_adc.c
> index 53bf7d4899d2..ab25e6e1ff65 100644
> --- a/drivers/iio/adc/axp20x_adc.c
> +++ b/drivers/iio/adc/axp20x_adc.c
> @@ -5,6 +5,7 @@
>   *     Quentin Schulz <quentin.schulz@free-electrons.com>
>   */
>
> +#include <linux/bitfield.h>
>  #include <linux/completion.h>
>  #include <linux/interrupt.h>
>  #include <linux/io.h>
> @@ -22,20 +23,20 @@
>  #include <linux/mfd/axp20x.h>
>
>  #define AXP20X_ADC_EN1_MASK                    GENMASK(7, 0)
> -
>  #define AXP20X_ADC_EN2_MASK                    (GENMASK(3, 2) | BIT(7))
> +
>  #define AXP22X_ADC_EN1_MASK                    (GENMASK(7, 5) | BIT(0))
>
>  #define AXP20X_GPIO10_IN_RANGE_GPIO0           BIT(0)
>  #define AXP20X_GPIO10_IN_RANGE_GPIO1           BIT(1)
> -#define AXP20X_GPIO10_IN_RANGE_GPIO0_VAL(x)    ((x) & BIT(0))
> -#define AXP20X_GPIO10_IN_RANGE_GPIO1_VAL(x)    (((x) & BIT(0)) << 1)
>
>  #define AXP20X_ADC_RATE_MASK                   GENMASK(7, 6)
> -#define AXP813_V_I_ADC_RATE_MASK               GENMASK(5, 4)
> -#define AXP813_ADC_RATE_MASK                   (AXP20X_ADC_RATE_MASK | AXP813_V_I_ADC_RATE_MASK)
>  #define AXP20X_ADC_RATE_HZ(x)                  ((ilog2((x) / 25) << 6) & AXP20X_ADC_RATE_MASK)
> +
>  #define AXP22X_ADC_RATE_HZ(x)                  ((ilog2((x) / 100) << 6) & AXP20X_ADC_RATE_MASK)
> +
> +#define AXP813_V_I_ADC_RATE_MASK               GENMASK(5, 4)
> +#define AXP813_ADC_RATE_MASK                   (AXP20X_ADC_RATE_MASK | AXP813_V_I_ADC_RATE_MASK)
>  #define AXP813_TS_GPIO0_ADC_RATE_HZ(x)         AXP20X_ADC_RATE_HZ(x)
>  #define AXP813_V_I_ADC_RATE_HZ(x)              ((ilog2((x) / 100) << 4) & AXP813_V_I_ADC_RATE_MASK)
>  #define AXP813_ADC_RATE_HZ(x)                  (AXP20X_ADC_RATE_HZ(x) | AXP813_V_I_ADC_RATE_HZ(x))
> @@ -234,7 +235,7 @@ static int axp20x_adc_raw(struct iio_dev *indio_dev,
>                           struct iio_chan_spec const *chan, int *val)
>  {
>         struct axp20x_adc_iio *info = iio_priv(indio_dev);
> -       int size = 12;
> +       int ret, size;
>
>         /*
>          * N.B.:  Unlike the Chinese datasheets tell, the charging current is
> @@ -246,10 +247,11 @@ static int axp20x_adc_raw(struct iio_dev *indio_dev,
>         else
>                 size = 12;
>
> -       *val = axp20x_read_variable_width(info->regmap, chan->address, size);
> -       if (*val < 0)
> -               return *val;
> +       ret = axp20x_read_variable_width(info->regmap, chan->address, size);
> +       if (ret < 0)
> +               return ret;
>
> +       *val = ret;
>         return IIO_VAL_INT;
>  }
>
> @@ -257,11 +259,13 @@ static int axp22x_adc_raw(struct iio_dev *indio_dev,
>                           struct iio_chan_spec const *chan, int *val)
>  {
>         struct axp20x_adc_iio *info = iio_priv(indio_dev);
> +       int ret;
>
> -       *val = axp20x_read_variable_width(info->regmap, chan->address, 12);
> -       if (*val < 0)
> -               return *val;
> +       ret = axp20x_read_variable_width(info->regmap, chan->address, 12);
> +       if (ret < 0)
> +               return ret;
>
> +       *val = ret;
>         return IIO_VAL_INT;
>  }
>
> @@ -269,11 +273,13 @@ static int axp813_adc_raw(struct iio_dev *indio_dev,
>                           struct iio_chan_spec const *chan, int *val)
>  {
>         struct axp20x_adc_iio *info = iio_priv(indio_dev);
> +       int ret;
>
> -       *val = axp20x_read_variable_width(info->regmap, chan->address, 12);
> -       if (*val < 0)
> -               return *val;
> +       ret = axp20x_read_variable_width(info->regmap, chan->address, 12);
> +       if (ret < 0)
> +               return ret;
>
> +       *val = ret;
>         return IIO_VAL_INT;
>  }
>
> @@ -443,27 +449,27 @@ static int axp20x_adc_offset_voltage(struct iio_dev *indio_dev, int channel,
>                                      int *val)
>  {
>         struct axp20x_adc_iio *info = iio_priv(indio_dev);
> +       unsigned int regval;
>         int ret;
>
> -       ret = regmap_read(info->regmap, AXP20X_GPIO10_IN_RANGE, val);
> +       ret = regmap_read(info->regmap, AXP20X_GPIO10_IN_RANGE, &regval);
>         if (ret < 0)
>                 return ret;
>
>         switch (channel) {
>         case AXP20X_GPIO0_V:
> -               *val &= AXP20X_GPIO10_IN_RANGE_GPIO0;
> +               regval = FIELD_GET(AXP20X_GPIO10_IN_RANGE_GPIO0, regval);
>                 break;
>
>         case AXP20X_GPIO1_V:
> -               *val &= AXP20X_GPIO10_IN_RANGE_GPIO1;
> +               regval = FIELD_GET(AXP20X_GPIO10_IN_RANGE_GPIO1, regval);
>                 break;
>
>         default:
>                 return -EINVAL;
>         }
>
> -       *val = *val ? 700000 : 0;
> -
> +       *val = regval ? 700000 : 0;
>         return IIO_VAL_INT;
>  }
>
> @@ -548,7 +554,7 @@ static int axp20x_write_raw(struct iio_dev *indio_dev,
>                             long mask)
>  {
>         struct axp20x_adc_iio *info = iio_priv(indio_dev);
> -       unsigned int reg, regval;
> +       unsigned int regmask, regval;
>
>         /*
>          * The AXP20X PMIC allows the user to choose between 0V and 0.7V offsets
> @@ -560,25 +566,22 @@ static int axp20x_write_raw(struct iio_dev *indio_dev,
>         if (val != 0 && val != 700000)
>                 return -EINVAL;
>
> -       val = val ? 1 : 0;
> -
>         switch (chan->channel) {
>         case AXP20X_GPIO0_V:
> -               reg = AXP20X_GPIO10_IN_RANGE_GPIO0;
> -               regval = AXP20X_GPIO10_IN_RANGE_GPIO0_VAL(val);
> +               regmask = AXP20X_GPIO10_IN_RANGE_GPIO0;
> +               regval = FIELD_PREP(AXP20X_GPIO10_IN_RANGE_GPIO0, !!val);
>                 break;
>
>         case AXP20X_GPIO1_V:
> -               reg = AXP20X_GPIO10_IN_RANGE_GPIO1;
> -               regval = AXP20X_GPIO10_IN_RANGE_GPIO1_VAL(val);
> +               regmask = AXP20X_GPIO10_IN_RANGE_GPIO1;
> +               regval = FIELD_PREP(AXP20X_GPIO10_IN_RANGE_GPIO1, !!val);
>                 break;
>
>         default:
>                 return -EINVAL;
>         }
>
> -       return regmap_update_bits(info->regmap, AXP20X_GPIO10_IN_RANGE, reg,
> -                                 regval);
> +       return regmap_update_bits(info->regmap, AXP20X_GPIO10_IN_RANGE, regmask, regval);
>  }
>
>  static const struct iio_info axp20x_adc_iio_info = {
> --
> 2.35.1
>


-- 
With Best Regards,
Andy Shevchenko

[PATCH v4 09/15] iio: adc: axp20x_adc: Replace adc_en2 flag with adc_en2_mask field

[Aidan MacDonald]

The adc_en2 flag is essentially specific to axp20x-compatible devices
because it hardcodes register values. Replace it with a mask field
so the register value can be specified in device match data.

Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
---
 drivers/iio/adc/axp20x_adc.c | 16 +++++++---------
 1 file changed, 7 insertions(+), 9 deletions(-)

diff --git a/drivers/iio/adc/axp20x_adc.c b/drivers/iio/adc/axp20x_adc.c
index ab25e6e1ff65..75bda94dbce1 100644
--- a/drivers/iio/adc/axp20x_adc.c
+++ b/drivers/iio/adc/axp20x_adc.c
@@ -623,9 +623,9 @@ struct axp_data {
 	int				num_channels;
 	struct iio_chan_spec const	*channels;
 	unsigned long			adc_en1_mask;
+	unsigned long			adc_en2_mask;
 	int				(*adc_rate)(struct axp20x_adc_iio *info,
 						    int rate);
-	bool				adc_en2;
 	struct iio_map			*maps;
 };
 
@@ -634,8 +634,8 @@ static const struct axp_data axp20x_data = {
 	.num_channels = ARRAY_SIZE(axp20x_adc_channels),
 	.channels = axp20x_adc_channels,
 	.adc_en1_mask = AXP20X_ADC_EN1_MASK,
+	.adc_en2_mask = AXP20X_ADC_EN2_MASK,
 	.adc_rate = axp20x_adc_rate,
-	.adc_en2 = true,
 	.maps = axp20x_maps,
 };
 
@@ -645,7 +645,6 @@ static const struct axp_data axp22x_data = {
 	.channels = axp22x_adc_channels,
 	.adc_en1_mask = AXP22X_ADC_EN1_MASK,
 	.adc_rate = axp22x_adc_rate,
-	.adc_en2 = false,
 	.maps = axp22x_maps,
 };
 
@@ -655,7 +654,6 @@ static const struct axp_data axp813_data = {
 	.channels = axp813_adc_channels,
 	.adc_en1_mask = AXP22X_ADC_EN1_MASK,
 	.adc_rate = axp813_adc_rate,
-	.adc_en2 = false,
 	.maps = axp22x_maps,
 };
 
@@ -713,10 +711,10 @@ static int axp20x_probe(struct platform_device *pdev)
 	/* Enable the ADCs on IP */
 	regmap_write(info->regmap, AXP20X_ADC_EN1, info->data->adc_en1_mask);
 
-	if (info->data->adc_en2)
-		/* Enable GPIO0/1 and internal temperature ADCs */
+	if (info->data->adc_en2_mask)
 		regmap_update_bits(info->regmap, AXP20X_ADC_EN2,
-				   AXP20X_ADC_EN2_MASK, AXP20X_ADC_EN2_MASK);
+				   info->data->adc_en2_mask,
+				   info->data->adc_en2_mask);
 
 	/* Configure ADCs rate */
 	info->data->adc_rate(info, 100);
@@ -741,7 +739,7 @@ static int axp20x_probe(struct platform_device *pdev)
 fail_map:
 	regmap_write(info->regmap, AXP20X_ADC_EN1, 0);
 
-	if (info->data->adc_en2)
+	if (info->data->adc_en2_mask)
 		regmap_write(info->regmap, AXP20X_ADC_EN2, 0);
 
 	return ret;
@@ -757,7 +755,7 @@ static int axp20x_remove(struct platform_device *pdev)
 
 	regmap_write(info->regmap, AXP20X_ADC_EN1, 0);
 
-	if (info->data->adc_en2)
+	if (info->data->adc_en2_mask)
 		regmap_write(info->regmap, AXP20X_ADC_EN2, 0);
 
 	return 0;
-- 
2.35.1

Re: [PATCH v4 09/15] iio: adc: axp20x_adc: Replace adc_en2 flag with adc_en2_mask field

[Andy Shevchenko]

On Wed, Jun 29, 2022 at 4:30 PM Aidan MacDonald
<aidanmacdonald.0x0@gmail.com> wrote:
>
> The adc_en2 flag is essentially specific to axp20x-compatible devices
> because it hardcodes register values. Replace it with a mask field
> so the register value can be specified in device match data.

Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>

> Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
> ---
>  drivers/iio/adc/axp20x_adc.c | 16 +++++++---------
>  1 file changed, 7 insertions(+), 9 deletions(-)
>
> diff --git a/drivers/iio/adc/axp20x_adc.c b/drivers/iio/adc/axp20x_adc.c
> index ab25e6e1ff65..75bda94dbce1 100644
> --- a/drivers/iio/adc/axp20x_adc.c
> +++ b/drivers/iio/adc/axp20x_adc.c
> @@ -623,9 +623,9 @@ struct axp_data {
>         int                             num_channels;
>         struct iio_chan_spec const      *channels;
>         unsigned long                   adc_en1_mask;
> +       unsigned long                   adc_en2_mask;
>         int                             (*adc_rate)(struct axp20x_adc_iio *info,
>                                                     int rate);
> -       bool                            adc_en2;
>         struct iio_map                  *maps;
>  };
>
> @@ -634,8 +634,8 @@ static const struct axp_data axp20x_data = {
>         .num_channels = ARRAY_SIZE(axp20x_adc_channels),
>         .channels = axp20x_adc_channels,
>         .adc_en1_mask = AXP20X_ADC_EN1_MASK,
> +       .adc_en2_mask = AXP20X_ADC_EN2_MASK,
>         .adc_rate = axp20x_adc_rate,
> -       .adc_en2 = true,
>         .maps = axp20x_maps,
>  };
>
> @@ -645,7 +645,6 @@ static const struct axp_data axp22x_data = {
>         .channels = axp22x_adc_channels,
>         .adc_en1_mask = AXP22X_ADC_EN1_MASK,
>         .adc_rate = axp22x_adc_rate,
> -       .adc_en2 = false,
>         .maps = axp22x_maps,
>  };
>
> @@ -655,7 +654,6 @@ static const struct axp_data axp813_data = {
>         .channels = axp813_adc_channels,
>         .adc_en1_mask = AXP22X_ADC_EN1_MASK,
>         .adc_rate = axp813_adc_rate,
> -       .adc_en2 = false,
>         .maps = axp22x_maps,
>  };
>
> @@ -713,10 +711,10 @@ static int axp20x_probe(struct platform_device *pdev)
>         /* Enable the ADCs on IP */
>         regmap_write(info->regmap, AXP20X_ADC_EN1, info->data->adc_en1_mask);
>
> -       if (info->data->adc_en2)
> -               /* Enable GPIO0/1 and internal temperature ADCs */
> +       if (info->data->adc_en2_mask)
>                 regmap_update_bits(info->regmap, AXP20X_ADC_EN2,
> -                                  AXP20X_ADC_EN2_MASK, AXP20X_ADC_EN2_MASK);
> +                                  info->data->adc_en2_mask,
> +                                  info->data->adc_en2_mask);
>
>         /* Configure ADCs rate */
>         info->data->adc_rate(info, 100);
> @@ -741,7 +739,7 @@ static int axp20x_probe(struct platform_device *pdev)
>  fail_map:
>         regmap_write(info->regmap, AXP20X_ADC_EN1, 0);
>
> -       if (info->data->adc_en2)
> +       if (info->data->adc_en2_mask)
>                 regmap_write(info->regmap, AXP20X_ADC_EN2, 0);
>
>         return ret;
> @@ -757,7 +755,7 @@ static int axp20x_remove(struct platform_device *pdev)
>
>         regmap_write(info->regmap, AXP20X_ADC_EN1, 0);
>
> -       if (info->data->adc_en2)
> +       if (info->data->adc_en2_mask)
>                 regmap_write(info->regmap, AXP20X_ADC_EN2, 0);
>
>         return 0;
> --
> 2.35.1
>


-- 
With Best Regards,
Andy Shevchenko

Re: [PATCH v4 09/15] iio: adc: axp20x_adc: Replace adc_en2 flag with adc_en2_mask field

[Jonathan Cameron]

On Wed, 29 Jun 2022 15:30:40 +0100
Aidan MacDonald <aidanmacdonald.0x0@gmail.com> wrote:

> The adc_en2 flag is essentially specific to axp20x-compatible devices
> because it hardcodes register values. Replace it with a mask field
> so the register value can be specified in device match data.
> 
> Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

> ---
>  drivers/iio/adc/axp20x_adc.c | 16 +++++++---------
>  1 file changed, 7 insertions(+), 9 deletions(-)
> 
> diff --git a/drivers/iio/adc/axp20x_adc.c b/drivers/iio/adc/axp20x_adc.c
> index ab25e6e1ff65..75bda94dbce1 100644
> --- a/drivers/iio/adc/axp20x_adc.c
> +++ b/drivers/iio/adc/axp20x_adc.c
> @@ -623,9 +623,9 @@ struct axp_data {
>  	int				num_channels;
>  	struct iio_chan_spec const	*channels;
>  	unsigned long			adc_en1_mask;
> +	unsigned long			adc_en2_mask;
>  	int				(*adc_rate)(struct axp20x_adc_iio *info,
>  						    int rate);
> -	bool				adc_en2;
>  	struct iio_map			*maps;
>  };
>  
> @@ -634,8 +634,8 @@ static const struct axp_data axp20x_data = {
>  	.num_channels = ARRAY_SIZE(axp20x_adc_channels),
>  	.channels = axp20x_adc_channels,
>  	.adc_en1_mask = AXP20X_ADC_EN1_MASK,
> +	.adc_en2_mask = AXP20X_ADC_EN2_MASK,
>  	.adc_rate = axp20x_adc_rate,
> -	.adc_en2 = true,
>  	.maps = axp20x_maps,
>  };
>  
> @@ -645,7 +645,6 @@ static const struct axp_data axp22x_data = {
>  	.channels = axp22x_adc_channels,
>  	.adc_en1_mask = AXP22X_ADC_EN1_MASK,
>  	.adc_rate = axp22x_adc_rate,
> -	.adc_en2 = false,
>  	.maps = axp22x_maps,
>  };
>  
> @@ -655,7 +654,6 @@ static const struct axp_data axp813_data = {
>  	.channels = axp813_adc_channels,
>  	.adc_en1_mask = AXP22X_ADC_EN1_MASK,
>  	.adc_rate = axp813_adc_rate,
> -	.adc_en2 = false,
>  	.maps = axp22x_maps,
>  };
>  
> @@ -713,10 +711,10 @@ static int axp20x_probe(struct platform_device *pdev)
>  	/* Enable the ADCs on IP */
>  	regmap_write(info->regmap, AXP20X_ADC_EN1, info->data->adc_en1_mask);
>  
> -	if (info->data->adc_en2)
> -		/* Enable GPIO0/1 and internal temperature ADCs */
> +	if (info->data->adc_en2_mask)
>  		regmap_update_bits(info->regmap, AXP20X_ADC_EN2,
> -				   AXP20X_ADC_EN2_MASK, AXP20X_ADC_EN2_MASK);
> +				   info->data->adc_en2_mask,
> +				   info->data->adc_en2_mask);
>  
>  	/* Configure ADCs rate */
>  	info->data->adc_rate(info, 100);
> @@ -741,7 +739,7 @@ static int axp20x_probe(struct platform_device *pdev)
>  fail_map:
>  	regmap_write(info->regmap, AXP20X_ADC_EN1, 0);
>  
> -	if (info->data->adc_en2)
> +	if (info->data->adc_en2_mask)
>  		regmap_write(info->regmap, AXP20X_ADC_EN2, 0);
>  
>  	return ret;
> @@ -757,7 +755,7 @@ static int axp20x_remove(struct platform_device *pdev)
>  
>  	regmap_write(info->regmap, AXP20X_ADC_EN1, 0);
>  
> -	if (info->data->adc_en2)
> +	if (info->data->adc_en2_mask)
>  		regmap_write(info->regmap, AXP20X_ADC_EN2, 0);
>  
>  	return 0;

[PATCH v4 10/15] iio: adc: axp20x_adc: Add support for AXP192

[Aidan MacDonald]

The AXP192 is identical to the AXP20x, except for the addition of
two more GPIO ADC channels.

Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
---
 drivers/iio/adc/axp20x_adc.c | 279 +++++++++++++++++++++++++++++++++++
 1 file changed, 279 insertions(+)

diff --git a/drivers/iio/adc/axp20x_adc.c b/drivers/iio/adc/axp20x_adc.c
index 75bda94dbce1..8d748b814f20 100644
--- a/drivers/iio/adc/axp20x_adc.c
+++ b/drivers/iio/adc/axp20x_adc.c
@@ -22,11 +22,19 @@
 #include <linux/iio/machine.h>
 #include <linux/mfd/axp20x.h>
 
+#define AXP192_ADC_EN1_MASK			GENMASK(7, 0)
+#define AXP192_ADC_EN2_MASK			(GENMASK(3, 0) | BIT(7))
+
 #define AXP20X_ADC_EN1_MASK			GENMASK(7, 0)
 #define AXP20X_ADC_EN2_MASK			(GENMASK(3, 2) | BIT(7))
 
 #define AXP22X_ADC_EN1_MASK			(GENMASK(7, 5) | BIT(0))
 
+#define AXP192_GPIO30_IN_RANGE_GPIO0		BIT(0)
+#define AXP192_GPIO30_IN_RANGE_GPIO1		BIT(1)
+#define AXP192_GPIO30_IN_RANGE_GPIO2		BIT(2)
+#define AXP192_GPIO30_IN_RANGE_GPIO3		BIT(3)
+
 #define AXP20X_GPIO10_IN_RANGE_GPIO0		BIT(0)
 #define AXP20X_GPIO10_IN_RANGE_GPIO1		BIT(1)
 
@@ -71,6 +79,25 @@ struct axp20x_adc_iio {
 	const struct axp_data	*data;
 };
 
+enum axp192_adc_channel_v {
+	AXP192_ACIN_V = 0,
+	AXP192_VBUS_V,
+	AXP192_TS_IN,
+	AXP192_GPIO0_V,
+	AXP192_GPIO1_V,
+	AXP192_GPIO2_V,
+	AXP192_GPIO3_V,
+	AXP192_IPSOUT_V,
+	AXP192_BATT_V,
+};
+
+enum axp192_adc_channel_i {
+	AXP192_ACIN_I = 0,
+	AXP192_VBUS_I,
+	AXP192_BATT_CHRG_I,
+	AXP192_BATT_DISCHRG_I,
+};
+
 enum axp20x_adc_channel_v {
 	AXP20X_ACIN_V = 0,
 	AXP20X_VBUS_V,
@@ -158,6 +185,43 @@ static struct iio_map axp22x_maps[] = {
  * The only exception is for the battery. batt_v will be in_voltage6_raw and
  * charge current in_current6_raw and discharge current will be in_current7_raw.
  */
+static const struct iio_chan_spec axp192_adc_channels[] = {
+	AXP20X_ADC_CHANNEL(AXP192_ACIN_V, "acin_v", IIO_VOLTAGE,
+			   AXP20X_ACIN_V_ADC_H),
+	AXP20X_ADC_CHANNEL(AXP192_ACIN_I, "acin_i", IIO_CURRENT,
+			   AXP20X_ACIN_I_ADC_H),
+	AXP20X_ADC_CHANNEL(AXP192_VBUS_V, "vbus_v", IIO_VOLTAGE,
+			   AXP20X_VBUS_V_ADC_H),
+	AXP20X_ADC_CHANNEL(AXP192_VBUS_I, "vbus_i", IIO_CURRENT,
+			   AXP20X_VBUS_I_ADC_H),
+	{
+		.type = IIO_TEMP,
+		.address = AXP20X_TEMP_ADC_H,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
+				      BIT(IIO_CHAN_INFO_SCALE) |
+				      BIT(IIO_CHAN_INFO_OFFSET),
+		.datasheet_name = "pmic_temp",
+	},
+	AXP20X_ADC_CHANNEL_OFFSET(AXP192_GPIO0_V, "gpio0_v", IIO_VOLTAGE,
+				  AXP20X_GPIO0_V_ADC_H),
+	AXP20X_ADC_CHANNEL_OFFSET(AXP192_GPIO1_V, "gpio1_v", IIO_VOLTAGE,
+				  AXP20X_GPIO1_V_ADC_H),
+	AXP20X_ADC_CHANNEL_OFFSET(AXP192_GPIO2_V, "gpio2_v", IIO_VOLTAGE,
+				  AXP192_GPIO2_V_ADC_H),
+	AXP20X_ADC_CHANNEL_OFFSET(AXP192_GPIO3_V, "gpio3_v", IIO_VOLTAGE,
+				  AXP192_GPIO3_V_ADC_H),
+	AXP20X_ADC_CHANNEL(AXP192_IPSOUT_V, "ipsout_v", IIO_VOLTAGE,
+			   AXP20X_IPSOUT_V_HIGH_H),
+	AXP20X_ADC_CHANNEL(AXP192_BATT_V, "batt_v", IIO_VOLTAGE,
+			   AXP20X_BATT_V_H),
+	AXP20X_ADC_CHANNEL(AXP192_BATT_CHRG_I, "batt_chrg_i", IIO_CURRENT,
+			   AXP20X_BATT_CHRG_I_H),
+	AXP20X_ADC_CHANNEL(AXP192_BATT_DISCHRG_I, "batt_dischrg_i", IIO_CURRENT,
+			   AXP20X_BATT_DISCHRG_I_H),
+	AXP20X_ADC_CHANNEL(AXP192_TS_IN, "ts_v", IIO_VOLTAGE,
+			   AXP20X_TS_IN_H),
+};
+
 static const struct iio_chan_spec axp20x_adc_channels[] = {
 	AXP20X_ADC_CHANNEL(AXP20X_ACIN_V, "acin_v", IIO_VOLTAGE,
 			   AXP20X_ACIN_V_ADC_H),
@@ -231,6 +295,27 @@ static const struct iio_chan_spec axp813_adc_channels[] = {
 			   AXP288_TS_ADC_H),
 };
 
+static int axp192_adc_raw(struct iio_dev *indio_dev,
+			  struct iio_chan_spec const *chan, int *val)
+{
+	struct axp20x_adc_iio *info = iio_priv(indio_dev);
+	int ret, size;
+
+	if (chan->type == IIO_CURRENT &&
+	    (chan->channel == AXP192_BATT_CHRG_I ||
+	     chan->channel == AXP192_BATT_DISCHRG_I))
+		size = 13;
+	else
+		size = 12;
+
+	ret = axp20x_read_variable_width(info->regmap, chan->address, size);
+	if (ret < 0)
+		return ret;
+
+	*val = ret;
+	return IIO_VAL_INT;
+}
+
 static int axp20x_adc_raw(struct iio_dev *indio_dev,
 			  struct iio_chan_spec const *chan, int *val)
 {
@@ -283,6 +368,44 @@ static int axp813_adc_raw(struct iio_dev *indio_dev,
 	return IIO_VAL_INT;
 }
 
+static int axp192_adc_scale_voltage(int channel, int *val, int *val2)
+{
+	switch (channel) {
+	case AXP192_ACIN_V:
+	case AXP192_VBUS_V:
+		*val = 1;
+		*val2 = 700000;
+		return IIO_VAL_INT_PLUS_MICRO;
+
+	case AXP192_GPIO0_V:
+	case AXP192_GPIO1_V:
+	case AXP192_GPIO2_V:
+	case AXP192_GPIO3_V:
+		*val = 0;
+		*val2 = 500000;
+		return IIO_VAL_INT_PLUS_MICRO;
+
+	case AXP192_BATT_V:
+		*val = 1;
+		*val2 = 100000;
+		return IIO_VAL_INT_PLUS_MICRO;
+
+	case AXP192_IPSOUT_V:
+		*val = 1;
+		*val2 = 400000;
+		return IIO_VAL_INT_PLUS_MICRO;
+
+	case AXP192_TS_IN:
+		/* 0.8 mV per LSB */
+		*val = 0;
+		*val2 = 800000;
+		return IIO_VAL_INT_PLUS_MICRO;
+
+	default:
+		return -EINVAL;
+	}
+}
+
 static int axp20x_adc_scale_voltage(int channel, int *val, int *val2)
 {
 	switch (channel) {
@@ -386,6 +509,29 @@ static int axp20x_adc_scale_current(int channel, int *val, int *val2)
 	}
 }
 
+static int axp192_adc_scale(struct iio_chan_spec const *chan, int *val,
+			    int *val2)
+{
+	switch (chan->type) {
+	case IIO_VOLTAGE:
+		return axp192_adc_scale_voltage(chan->channel, val, val2);
+
+	case IIO_CURRENT:
+		/*
+		 * AXP192 current channels are identical to the AXP20x,
+		 * therefore we can re-use the scaling function.
+		 */
+		return axp20x_adc_scale_current(chan->channel, val, val2);
+
+	case IIO_TEMP:
+		*val = 100;
+		return IIO_VAL_INT;
+
+	default:
+		return -EINVAL;
+	}
+}
+
 static int axp20x_adc_scale(struct iio_chan_spec const *chan, int *val,
 			    int *val2)
 {
@@ -445,6 +591,42 @@ static int axp813_adc_scale(struct iio_chan_spec const *chan, int *val,
 	}
 }
 
+static int axp192_adc_offset_voltage(struct iio_dev *indio_dev, int channel,
+				     int *val)
+{
+	struct axp20x_adc_iio *info = iio_priv(indio_dev);
+	unsigned int regval;
+	int ret;
+
+	ret = regmap_read(info->regmap, AXP192_GPIO30_IN_RANGE, &regval);
+	if (ret < 0)
+		return ret;
+
+	switch (channel) {
+	case AXP192_GPIO0_V:
+		regval = FIELD_GET(AXP192_GPIO30_IN_RANGE_GPIO0, regval);
+		break;
+
+	case AXP192_GPIO1_V:
+		regval = FIELD_GET(AXP192_GPIO30_IN_RANGE_GPIO1, regval);
+		break;
+
+	case AXP192_GPIO2_V:
+		regval = FIELD_GET(AXP192_GPIO30_IN_RANGE_GPIO2, regval);
+		break;
+
+	case AXP192_GPIO3_V:
+		regval = FIELD_GET(AXP192_GPIO30_IN_RANGE_GPIO3, regval);
+		break;
+
+	default:
+		return -EINVAL;
+	}
+
+	*val = regval ? 700000 : 0;
+	return IIO_VAL_INT;
+}
+
 static int axp20x_adc_offset_voltage(struct iio_dev *indio_dev, int channel,
 				     int *val)
 {
@@ -473,6 +655,22 @@ static int axp20x_adc_offset_voltage(struct iio_dev *indio_dev, int channel,
 	return IIO_VAL_INT;
 }
 
+static int axp192_adc_offset(struct iio_dev *indio_dev,
+			     struct iio_chan_spec const *chan, int *val)
+{
+	switch (chan->type) {
+	case IIO_VOLTAGE:
+		return axp192_adc_offset_voltage(indio_dev, chan->channel, val);
+
+	case IIO_TEMP:
+		*val = -1447;
+		return IIO_VAL_INT;
+
+	default:
+		return -EINVAL;
+	}
+}
+
 static int axp20x_adc_offset(struct iio_dev *indio_dev,
 			     struct iio_chan_spec const *chan, int *val)
 {
@@ -489,6 +687,25 @@ static int axp20x_adc_offset(struct iio_dev *indio_dev,
 	}
 }
 
+static int axp192_read_raw(struct iio_dev *indio_dev,
+			   struct iio_chan_spec const *chan, int *val,
+			   int *val2, long mask)
+{
+	switch (mask) {
+	case IIO_CHAN_INFO_OFFSET:
+		return axp192_adc_offset(indio_dev, chan, val);
+
+	case IIO_CHAN_INFO_SCALE:
+		return axp192_adc_scale(chan, val, val2);
+
+	case IIO_CHAN_INFO_RAW:
+		return axp192_adc_raw(indio_dev, chan, val);
+
+	default:
+		return -EINVAL;
+	}
+}
+
 static int axp20x_read_raw(struct iio_dev *indio_dev,
 			   struct iio_chan_spec const *chan, int *val,
 			   int *val2, long mask)
@@ -549,6 +766,51 @@ static int axp813_read_raw(struct iio_dev *indio_dev,
 	}
 }
 
+static int axp192_write_raw(struct iio_dev *indio_dev,
+			    struct iio_chan_spec const *chan, int val, int val2,
+			    long mask)
+{
+	struct axp20x_adc_iio *info = iio_priv(indio_dev);
+	unsigned int regmask, regval;
+
+	/*
+	 * The AXP192 PMIC allows the user to choose between 0V and 0.7V offsets
+	 * for (independently) GPIO0-3 when in ADC mode.
+	 */
+	if (mask != IIO_CHAN_INFO_OFFSET)
+		return -EINVAL;
+
+	if (val != 0 && val != 700000)
+		return -EINVAL;
+
+	switch (chan->channel) {
+	case AXP192_GPIO0_V:
+		regmask = AXP192_GPIO30_IN_RANGE_GPIO0;
+		regval = FIELD_PREP(AXP192_GPIO30_IN_RANGE_GPIO0, !!val);
+		break;
+
+	case AXP192_GPIO1_V:
+		regmask = AXP192_GPIO30_IN_RANGE_GPIO1;
+		regval = FIELD_PREP(AXP192_GPIO30_IN_RANGE_GPIO1, !!val);
+		break;
+
+	case AXP192_GPIO2_V:
+		regmask = AXP192_GPIO30_IN_RANGE_GPIO2;
+		regval = FIELD_PREP(AXP192_GPIO30_IN_RANGE_GPIO2, !!val);
+		break;
+
+	case AXP192_GPIO3_V:
+		regmask = AXP192_GPIO30_IN_RANGE_GPIO3;
+		regval = FIELD_PREP(AXP192_GPIO30_IN_RANGE_GPIO3, !!val);
+		break;
+
+	default:
+		return -EINVAL;
+	}
+
+	return regmap_update_bits(info->regmap, AXP192_GPIO30_IN_RANGE, regmask, regval);
+}
+
 static int axp20x_write_raw(struct iio_dev *indio_dev,
 			    struct iio_chan_spec const *chan, int val, int val2,
 			    long mask)
@@ -584,6 +846,11 @@ static int axp20x_write_raw(struct iio_dev *indio_dev,
 	return regmap_update_bits(info->regmap, AXP20X_GPIO10_IN_RANGE, regmask, regval);
 }
 
+static const struct iio_info axp192_adc_iio_info = {
+	.read_raw = axp192_read_raw,
+	.write_raw = axp192_write_raw,
+};
+
 static const struct iio_info axp20x_adc_iio_info = {
 	.read_raw = axp20x_read_raw,
 	.write_raw = axp20x_write_raw,
@@ -629,6 +896,16 @@ struct axp_data {
 	struct iio_map			*maps;
 };
 
+static const struct axp_data axp192_data = {
+	.iio_info = &axp192_adc_iio_info,
+	.num_channels = ARRAY_SIZE(axp192_adc_channels),
+	.channels = axp192_adc_channels,
+	.adc_en1_mask = AXP192_ADC_EN1_MASK,
+	.adc_en2_mask = AXP192_ADC_EN2_MASK,
+	.adc_rate = axp20x_adc_rate,
+	.maps = axp20x_maps,
+};
+
 static const struct axp_data axp20x_data = {
 	.iio_info = &axp20x_adc_iio_info,
 	.num_channels = ARRAY_SIZE(axp20x_adc_channels),
@@ -658,6 +935,7 @@ static const struct axp_data axp813_data = {
 };
 
 static const struct of_device_id axp20x_adc_of_match[] = {
+	{ .compatible = "x-powers,axp192-adc", .data = (void *)&axp192_data, },
 	{ .compatible = "x-powers,axp209-adc", .data = (void *)&axp20x_data, },
 	{ .compatible = "x-powers,axp221-adc", .data = (void *)&axp22x_data, },
 	{ .compatible = "x-powers,axp813-adc", .data = (void *)&axp813_data, },
@@ -666,6 +944,7 @@ static const struct of_device_id axp20x_adc_of_match[] = {
 MODULE_DEVICE_TABLE(of, axp20x_adc_of_match);
 
 static const struct platform_device_id axp20x_adc_id_match[] = {
+	{ .name = "axp192-adc", .driver_data = (kernel_ulong_t)&axp192_data, },
 	{ .name = "axp20x-adc", .driver_data = (kernel_ulong_t)&axp20x_data, },
 	{ .name = "axp22x-adc", .driver_data = (kernel_ulong_t)&axp22x_data, },
 	{ .name = "axp813-adc", .driver_data = (kernel_ulong_t)&axp813_data, },
-- 
2.35.1

Re: [PATCH v4 10/15] iio: adc: axp20x_adc: Add support for AXP192

[Andy Shevchenko]

On Wed, Jun 29, 2022 at 4:30 PM Aidan MacDonald
<aidanmacdonald.0x0@gmail.com> wrote:
>
> The AXP192 is identical to the AXP20x, except for the addition of
> two more GPIO ADC channels.

Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>

> Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
> Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
> ---
>  drivers/iio/adc/axp20x_adc.c | 279 +++++++++++++++++++++++++++++++++++
>  1 file changed, 279 insertions(+)
>
> diff --git a/drivers/iio/adc/axp20x_adc.c b/drivers/iio/adc/axp20x_adc.c
> index 75bda94dbce1..8d748b814f20 100644
> --- a/drivers/iio/adc/axp20x_adc.c
> +++ b/drivers/iio/adc/axp20x_adc.c
> @@ -22,11 +22,19 @@
>  #include <linux/iio/machine.h>
>  #include <linux/mfd/axp20x.h>
>
> +#define AXP192_ADC_EN1_MASK                    GENMASK(7, 0)
> +#define AXP192_ADC_EN2_MASK                    (GENMASK(3, 0) | BIT(7))
> +
>  #define AXP20X_ADC_EN1_MASK                    GENMASK(7, 0)
>  #define AXP20X_ADC_EN2_MASK                    (GENMASK(3, 2) | BIT(7))
>
>  #define AXP22X_ADC_EN1_MASK                    (GENMASK(7, 5) | BIT(0))
>
> +#define AXP192_GPIO30_IN_RANGE_GPIO0           BIT(0)
> +#define AXP192_GPIO30_IN_RANGE_GPIO1           BIT(1)
> +#define AXP192_GPIO30_IN_RANGE_GPIO2           BIT(2)
> +#define AXP192_GPIO30_IN_RANGE_GPIO3           BIT(3)
> +
>  #define AXP20X_GPIO10_IN_RANGE_GPIO0           BIT(0)
>  #define AXP20X_GPIO10_IN_RANGE_GPIO1           BIT(1)
>
> @@ -71,6 +79,25 @@ struct axp20x_adc_iio {
>         const struct axp_data   *data;
>  };
>
> +enum axp192_adc_channel_v {
> +       AXP192_ACIN_V = 0,
> +       AXP192_VBUS_V,
> +       AXP192_TS_IN,
> +       AXP192_GPIO0_V,
> +       AXP192_GPIO1_V,
> +       AXP192_GPIO2_V,
> +       AXP192_GPIO3_V,
> +       AXP192_IPSOUT_V,
> +       AXP192_BATT_V,
> +};
> +
> +enum axp192_adc_channel_i {
> +       AXP192_ACIN_I = 0,
> +       AXP192_VBUS_I,
> +       AXP192_BATT_CHRG_I,
> +       AXP192_BATT_DISCHRG_I,
> +};
> +
>  enum axp20x_adc_channel_v {
>         AXP20X_ACIN_V = 0,
>         AXP20X_VBUS_V,
> @@ -158,6 +185,43 @@ static struct iio_map axp22x_maps[] = {
>   * The only exception is for the battery. batt_v will be in_voltage6_raw and
>   * charge current in_current6_raw and discharge current will be in_current7_raw.
>   */
> +static const struct iio_chan_spec axp192_adc_channels[] = {
> +       AXP20X_ADC_CHANNEL(AXP192_ACIN_V, "acin_v", IIO_VOLTAGE,
> +                          AXP20X_ACIN_V_ADC_H),
> +       AXP20X_ADC_CHANNEL(AXP192_ACIN_I, "acin_i", IIO_CURRENT,
> +                          AXP20X_ACIN_I_ADC_H),
> +       AXP20X_ADC_CHANNEL(AXP192_VBUS_V, "vbus_v", IIO_VOLTAGE,
> +                          AXP20X_VBUS_V_ADC_H),
> +       AXP20X_ADC_CHANNEL(AXP192_VBUS_I, "vbus_i", IIO_CURRENT,
> +                          AXP20X_VBUS_I_ADC_H),
> +       {
> +               .type = IIO_TEMP,
> +               .address = AXP20X_TEMP_ADC_H,
> +               .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
> +                                     BIT(IIO_CHAN_INFO_SCALE) |
> +                                     BIT(IIO_CHAN_INFO_OFFSET),
> +               .datasheet_name = "pmic_temp",
> +       },
> +       AXP20X_ADC_CHANNEL_OFFSET(AXP192_GPIO0_V, "gpio0_v", IIO_VOLTAGE,
> +                                 AXP20X_GPIO0_V_ADC_H),
> +       AXP20X_ADC_CHANNEL_OFFSET(AXP192_GPIO1_V, "gpio1_v", IIO_VOLTAGE,
> +                                 AXP20X_GPIO1_V_ADC_H),
> +       AXP20X_ADC_CHANNEL_OFFSET(AXP192_GPIO2_V, "gpio2_v", IIO_VOLTAGE,
> +                                 AXP192_GPIO2_V_ADC_H),
> +       AXP20X_ADC_CHANNEL_OFFSET(AXP192_GPIO3_V, "gpio3_v", IIO_VOLTAGE,
> +                                 AXP192_GPIO3_V_ADC_H),
> +       AXP20X_ADC_CHANNEL(AXP192_IPSOUT_V, "ipsout_v", IIO_VOLTAGE,
> +                          AXP20X_IPSOUT_V_HIGH_H),
> +       AXP20X_ADC_CHANNEL(AXP192_BATT_V, "batt_v", IIO_VOLTAGE,
> +                          AXP20X_BATT_V_H),
> +       AXP20X_ADC_CHANNEL(AXP192_BATT_CHRG_I, "batt_chrg_i", IIO_CURRENT,
> +                          AXP20X_BATT_CHRG_I_H),
> +       AXP20X_ADC_CHANNEL(AXP192_BATT_DISCHRG_I, "batt_dischrg_i", IIO_CURRENT,
> +                          AXP20X_BATT_DISCHRG_I_H),
> +       AXP20X_ADC_CHANNEL(AXP192_TS_IN, "ts_v", IIO_VOLTAGE,
> +                          AXP20X_TS_IN_H),
> +};
> +
>  static const struct iio_chan_spec axp20x_adc_channels[] = {
>         AXP20X_ADC_CHANNEL(AXP20X_ACIN_V, "acin_v", IIO_VOLTAGE,
>                            AXP20X_ACIN_V_ADC_H),
> @@ -231,6 +295,27 @@ static const struct iio_chan_spec axp813_adc_channels[] = {
>                            AXP288_TS_ADC_H),
>  };
>
> +static int axp192_adc_raw(struct iio_dev *indio_dev,
> +                         struct iio_chan_spec const *chan, int *val)
> +{
> +       struct axp20x_adc_iio *info = iio_priv(indio_dev);
> +       int ret, size;
> +
> +       if (chan->type == IIO_CURRENT &&
> +           (chan->channel == AXP192_BATT_CHRG_I ||
> +            chan->channel == AXP192_BATT_DISCHRG_I))
> +               size = 13;
> +       else
> +               size = 12;
> +
> +       ret = axp20x_read_variable_width(info->regmap, chan->address, size);
> +       if (ret < 0)
> +               return ret;
> +
> +       *val = ret;
> +       return IIO_VAL_INT;
> +}
> +
>  static int axp20x_adc_raw(struct iio_dev *indio_dev,
>                           struct iio_chan_spec const *chan, int *val)
>  {
> @@ -283,6 +368,44 @@ static int axp813_adc_raw(struct iio_dev *indio_dev,
>         return IIO_VAL_INT;
>  }
>
> +static int axp192_adc_scale_voltage(int channel, int *val, int *val2)
> +{
> +       switch (channel) {
> +       case AXP192_ACIN_V:
> +       case AXP192_VBUS_V:
> +               *val = 1;
> +               *val2 = 700000;
> +               return IIO_VAL_INT_PLUS_MICRO;
> +
> +       case AXP192_GPIO0_V:
> +       case AXP192_GPIO1_V:
> +       case AXP192_GPIO2_V:
> +       case AXP192_GPIO3_V:
> +               *val = 0;
> +               *val2 = 500000;
> +               return IIO_VAL_INT_PLUS_MICRO;
> +
> +       case AXP192_BATT_V:
> +               *val = 1;
> +               *val2 = 100000;
> +               return IIO_VAL_INT_PLUS_MICRO;
> +
> +       case AXP192_IPSOUT_V:
> +               *val = 1;
> +               *val2 = 400000;
> +               return IIO_VAL_INT_PLUS_MICRO;
> +
> +       case AXP192_TS_IN:
> +               /* 0.8 mV per LSB */
> +               *val = 0;
> +               *val2 = 800000;
> +               return IIO_VAL_INT_PLUS_MICRO;
> +
> +       default:
> +               return -EINVAL;
> +       }
> +}
> +
>  static int axp20x_adc_scale_voltage(int channel, int *val, int *val2)
>  {
>         switch (channel) {
> @@ -386,6 +509,29 @@ static int axp20x_adc_scale_current(int channel, int *val, int *val2)
>         }
>  }
>
> +static int axp192_adc_scale(struct iio_chan_spec const *chan, int *val,
> +                           int *val2)
> +{
> +       switch (chan->type) {
> +       case IIO_VOLTAGE:
> +               return axp192_adc_scale_voltage(chan->channel, val, val2);
> +
> +       case IIO_CURRENT:
> +               /*
> +                * AXP192 current channels are identical to the AXP20x,
> +                * therefore we can re-use the scaling function.
> +                */
> +               return axp20x_adc_scale_current(chan->channel, val, val2);
> +
> +       case IIO_TEMP:
> +               *val = 100;
> +               return IIO_VAL_INT;
> +
> +       default:
> +               return -EINVAL;
> +       }
> +}
> +
>  static int axp20x_adc_scale(struct iio_chan_spec const *chan, int *val,
>                             int *val2)
>  {
> @@ -445,6 +591,42 @@ static int axp813_adc_scale(struct iio_chan_spec const *chan, int *val,
>         }
>  }
>
> +static int axp192_adc_offset_voltage(struct iio_dev *indio_dev, int channel,
> +                                    int *val)
> +{
> +       struct axp20x_adc_iio *info = iio_priv(indio_dev);
> +       unsigned int regval;
> +       int ret;
> +
> +       ret = regmap_read(info->regmap, AXP192_GPIO30_IN_RANGE, &regval);
> +       if (ret < 0)
> +               return ret;
> +
> +       switch (channel) {
> +       case AXP192_GPIO0_V:
> +               regval = FIELD_GET(AXP192_GPIO30_IN_RANGE_GPIO0, regval);
> +               break;
> +
> +       case AXP192_GPIO1_V:
> +               regval = FIELD_GET(AXP192_GPIO30_IN_RANGE_GPIO1, regval);
> +               break;
> +
> +       case AXP192_GPIO2_V:
> +               regval = FIELD_GET(AXP192_GPIO30_IN_RANGE_GPIO2, regval);
> +               break;
> +
> +       case AXP192_GPIO3_V:
> +               regval = FIELD_GET(AXP192_GPIO30_IN_RANGE_GPIO3, regval);
> +               break;
> +
> +       default:
> +               return -EINVAL;
> +       }
> +
> +       *val = regval ? 700000 : 0;
> +       return IIO_VAL_INT;
> +}
> +
>  static int axp20x_adc_offset_voltage(struct iio_dev *indio_dev, int channel,
>                                      int *val)
>  {
> @@ -473,6 +655,22 @@ static int axp20x_adc_offset_voltage(struct iio_dev *indio_dev, int channel,
>         return IIO_VAL_INT;
>  }
>
> +static int axp192_adc_offset(struct iio_dev *indio_dev,
> +                            struct iio_chan_spec const *chan, int *val)
> +{
> +       switch (chan->type) {
> +       case IIO_VOLTAGE:
> +               return axp192_adc_offset_voltage(indio_dev, chan->channel, val);
> +
> +       case IIO_TEMP:
> +               *val = -1447;
> +               return IIO_VAL_INT;
> +
> +       default:
> +               return -EINVAL;
> +       }
> +}
> +
>  static int axp20x_adc_offset(struct iio_dev *indio_dev,
>                              struct iio_chan_spec const *chan, int *val)
>  {
> @@ -489,6 +687,25 @@ static int axp20x_adc_offset(struct iio_dev *indio_dev,
>         }
>  }
>
> +static int axp192_read_raw(struct iio_dev *indio_dev,
> +                          struct iio_chan_spec const *chan, int *val,
> +                          int *val2, long mask)
> +{
> +       switch (mask) {
> +       case IIO_CHAN_INFO_OFFSET:
> +               return axp192_adc_offset(indio_dev, chan, val);
> +
> +       case IIO_CHAN_INFO_SCALE:
> +               return axp192_adc_scale(chan, val, val2);
> +
> +       case IIO_CHAN_INFO_RAW:
> +               return axp192_adc_raw(indio_dev, chan, val);
> +
> +       default:
> +               return -EINVAL;
> +       }
> +}
> +
>  static int axp20x_read_raw(struct iio_dev *indio_dev,
>                            struct iio_chan_spec const *chan, int *val,
>                            int *val2, long mask)
> @@ -549,6 +766,51 @@ static int axp813_read_raw(struct iio_dev *indio_dev,
>         }
>  }
>
> +static int axp192_write_raw(struct iio_dev *indio_dev,
> +                           struct iio_chan_spec const *chan, int val, int val2,
> +                           long mask)
> +{
> +       struct axp20x_adc_iio *info = iio_priv(indio_dev);
> +       unsigned int regmask, regval;
> +
> +       /*
> +        * The AXP192 PMIC allows the user to choose between 0V and 0.7V offsets
> +        * for (independently) GPIO0-3 when in ADC mode.
> +        */
> +       if (mask != IIO_CHAN_INFO_OFFSET)
> +               return -EINVAL;
> +
> +       if (val != 0 && val != 700000)
> +               return -EINVAL;
> +
> +       switch (chan->channel) {
> +       case AXP192_GPIO0_V:
> +               regmask = AXP192_GPIO30_IN_RANGE_GPIO0;
> +               regval = FIELD_PREP(AXP192_GPIO30_IN_RANGE_GPIO0, !!val);
> +               break;
> +
> +       case AXP192_GPIO1_V:
> +               regmask = AXP192_GPIO30_IN_RANGE_GPIO1;
> +               regval = FIELD_PREP(AXP192_GPIO30_IN_RANGE_GPIO1, !!val);
> +               break;
> +
> +       case AXP192_GPIO2_V:
> +               regmask = AXP192_GPIO30_IN_RANGE_GPIO2;
> +               regval = FIELD_PREP(AXP192_GPIO30_IN_RANGE_GPIO2, !!val);
> +               break;
> +
> +       case AXP192_GPIO3_V:
> +               regmask = AXP192_GPIO30_IN_RANGE_GPIO3;
> +               regval = FIELD_PREP(AXP192_GPIO30_IN_RANGE_GPIO3, !!val);
> +               break;
> +
> +       default:
> +               return -EINVAL;
> +       }
> +
> +       return regmap_update_bits(info->regmap, AXP192_GPIO30_IN_RANGE, regmask, regval);
> +}
> +
>  static int axp20x_write_raw(struct iio_dev *indio_dev,
>                             struct iio_chan_spec const *chan, int val, int val2,
>                             long mask)
> @@ -584,6 +846,11 @@ static int axp20x_write_raw(struct iio_dev *indio_dev,
>         return regmap_update_bits(info->regmap, AXP20X_GPIO10_IN_RANGE, regmask, regval);
>  }
>
> +static const struct iio_info axp192_adc_iio_info = {
> +       .read_raw = axp192_read_raw,
> +       .write_raw = axp192_write_raw,
> +};
> +
>  static const struct iio_info axp20x_adc_iio_info = {
>         .read_raw = axp20x_read_raw,
>         .write_raw = axp20x_write_raw,
> @@ -629,6 +896,16 @@ struct axp_data {
>         struct iio_map                  *maps;
>  };
>
> +static const struct axp_data axp192_data = {
> +       .iio_info = &axp192_adc_iio_info,
> +       .num_channels = ARRAY_SIZE(axp192_adc_channels),
> +       .channels = axp192_adc_channels,
> +       .adc_en1_mask = AXP192_ADC_EN1_MASK,
> +       .adc_en2_mask = AXP192_ADC_EN2_MASK,
> +       .adc_rate = axp20x_adc_rate,
> +       .maps = axp20x_maps,
> +};
> +
>  static const struct axp_data axp20x_data = {
>         .iio_info = &axp20x_adc_iio_info,
>         .num_channels = ARRAY_SIZE(axp20x_adc_channels),
> @@ -658,6 +935,7 @@ static const struct axp_data axp813_data = {
>  };
>
>  static const struct of_device_id axp20x_adc_of_match[] = {
> +       { .compatible = "x-powers,axp192-adc", .data = (void *)&axp192_data, },
>         { .compatible = "x-powers,axp209-adc", .data = (void *)&axp20x_data, },
>         { .compatible = "x-powers,axp221-adc", .data = (void *)&axp22x_data, },
>         { .compatible = "x-powers,axp813-adc", .data = (void *)&axp813_data, },
> @@ -666,6 +944,7 @@ static const struct of_device_id axp20x_adc_of_match[] = {
>  MODULE_DEVICE_TABLE(of, axp20x_adc_of_match);
>
>  static const struct platform_device_id axp20x_adc_id_match[] = {
> +       { .name = "axp192-adc", .driver_data = (kernel_ulong_t)&axp192_data, },
>         { .name = "axp20x-adc", .driver_data = (kernel_ulong_t)&axp20x_data, },
>         { .name = "axp22x-adc", .driver_data = (kernel_ulong_t)&axp22x_data, },
>         { .name = "axp813-adc", .driver_data = (kernel_ulong_t)&axp813_data, },
> --
> 2.35.1
>


-- 
With Best Regards,
Andy Shevchenko

[PATCH v4 11/15] power: supply: axp20x_usb_power: Add support for AXP192

[Aidan MacDonald]

The AXP192's USB power supply is similar to the AXP202 but it has
different USB current limits and a different offset for the VBUS
status register.

Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
---
 drivers/power/supply/axp20x_usb_power.c | 84 +++++++++++++++++++++----
 1 file changed, 73 insertions(+), 11 deletions(-)

diff --git a/drivers/power/supply/axp20x_usb_power.c b/drivers/power/supply/axp20x_usb_power.c
index a1e6d1d44808..f83e2ed6d507 100644
--- a/drivers/power/supply/axp20x_usb_power.c
+++ b/drivers/power/supply/axp20x_usb_power.c
@@ -48,6 +48,9 @@
 #define AXP813_VBUS_CLIMIT_2000mA	2
 #define AXP813_VBUS_CLIMIT_2500mA	3
 
+#define AXP192_VBUS_CLIMIT_EN		BIT(1)
+#define AXP192_VBUS_CLIMIT_100mA	BIT(0)
+
 #define AXP20X_ADC_EN1_VBUS_CURR	BIT(2)
 #define AXP20X_ADC_EN1_VBUS_VOLT	BIT(3)
 
@@ -121,6 +124,25 @@ static void axp20x_usb_power_poll_vbus(struct work_struct *work)
 		mod_delayed_work(system_power_efficient_wq, &power->vbus_detect, DEBOUNCE_TIME);
 }
 
+static int axp192_get_current_max(struct axp20x_usb_power *power, int *val)
+{
+	unsigned int v;
+	int ret;
+
+	ret = regmap_read(power->regmap, AXP20X_VBUS_IPSOUT_MGMT, &v);
+	if (ret)
+		return ret;
+
+	if (!(v & AXP192_VBUS_CLIMIT_EN))
+		*val = -1;
+	else if (v & AXP192_VBUS_CLIMIT_100mA)
+		*val = 100000;
+	else
+		*val = 500000;
+
+	return 0;
+}
+
 static int axp20x_get_current_max(struct axp20x_usb_power *power, int *val)
 {
 	unsigned int v;
@@ -179,7 +201,7 @@ static int axp20x_usb_power_get_property(struct power_supply *psy,
 	enum power_supply_property psp, union power_supply_propval *val)
 {
 	struct axp20x_usb_power *power = power_supply_get_drvdata(psy);
-	unsigned int input, v;
+	unsigned int input, v, reg;
 	int ret;
 
 	switch (psp) {
@@ -215,6 +237,8 @@ static int axp20x_usb_power_get_property(struct power_supply *psy,
 	case POWER_SUPPLY_PROP_CURRENT_MAX:
 		if (power->axp20x_id == AXP813_ID)
 			return axp813_get_current_max(power, &val->intval);
+		else if (power->axp20x_id == AXP192_ID)
+			return axp192_get_current_max(power, &val->intval);
 		return axp20x_get_current_max(power, &val->intval);
 	case POWER_SUPPLY_PROP_CURRENT_NOW:
 		if (IS_ENABLED(CONFIG_AXP20X_ADC)) {
@@ -256,16 +280,19 @@ static int axp20x_usb_power_get_property(struct power_supply *psy,
 
 		val->intval = POWER_SUPPLY_HEALTH_GOOD;
 
-		if (power->axp20x_id == AXP202_ID) {
-			ret = regmap_read(power->regmap,
-					  AXP20X_USB_OTG_STATUS, &v);
-			if (ret)
-				return ret;
+		if (power->axp20x_id == AXP192_ID)
+			reg = AXP192_USB_OTG_STATUS;
+		else if (power->axp20x_id == AXP202_ID)
+			reg = AXP20X_USB_OTG_STATUS;
+		else
+			break; /* Other chips lack the OTG status register */
 
-			if (!(v & AXP20X_USB_STATUS_VBUS_VALID))
-				val->intval =
-					POWER_SUPPLY_HEALTH_UNSPEC_FAILURE;
-		}
+		ret = regmap_read(power->regmap, reg, &v);
+		if (ret)
+			return ret;
+
+		if (!(v & AXP20X_USB_STATUS_VBUS_VALID))
+			val->intval = POWER_SUPPLY_HEALTH_UNSPEC_FAILURE;
 		break;
 	case POWER_SUPPLY_PROP_PRESENT:
 		val->intval = !!(input & AXP20X_PWR_STATUS_VBUS_PRESENT);
@@ -316,6 +343,28 @@ static int axp20x_usb_power_set_voltage_min(struct axp20x_usb_power *power,
 	return -EINVAL;
 }
 
+static int axp192_usb_power_set_current_max(struct axp20x_usb_power *power,
+					    int intval)
+{
+	const unsigned int mask = AXP192_VBUS_CLIMIT_EN |
+				  AXP192_VBUS_CLIMIT_100mA;
+	unsigned int val;
+
+	switch (intval) {
+	case 100000:
+		val = AXP192_VBUS_CLIMIT_EN | AXP192_VBUS_CLIMIT_100mA;
+		break;
+	case 500000:
+		val = AXP192_VBUS_CLIMIT_EN;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return regmap_update_bits(power->regmap,
+				  AXP20X_VBUS_IPSOUT_MGMT, mask, val);
+}
+
 static int axp813_usb_power_set_current_max(struct axp20x_usb_power *power,
 					    int intval)
 {
@@ -383,6 +432,9 @@ static int axp20x_usb_power_set_property(struct power_supply *psy,
 		if (power->axp20x_id == AXP813_ID)
 			return axp813_usb_power_set_current_max(power,
 								val->intval);
+		else if (power->axp20x_id == AXP192_ID)
+			return axp192_usb_power_set_current_max(power,
+								val->intval);
 		return axp20x_usb_power_set_current_max(power, val->intval);
 
 	default:
@@ -468,6 +520,13 @@ struct axp_data {
 	enum axp20x_variants		axp20x_id;
 };
 
+static const struct axp_data axp192_data = {
+	.power_desc	= &axp20x_usb_power_desc,
+	.irq_names	= axp20x_irq_names,
+	.num_irq_names	= ARRAY_SIZE(axp20x_irq_names),
+	.axp20x_id	= AXP192_ID,
+};
+
 static const struct axp_data axp202_data = {
 	.power_desc	= &axp20x_usb_power_desc,
 	.irq_names	= axp20x_irq_names,
@@ -600,7 +659,7 @@ static int axp20x_usb_power_probe(struct platform_device *pdev)
 	if (ret)
 		return ret;
 
-	if (power->axp20x_id == AXP202_ID) {
+	if (power->axp20x_id == AXP192_ID || power->axp20x_id == AXP202_ID) {
 		/* Enable vbus valid checking */
 		ret = regmap_update_bits(power->regmap, AXP20X_VBUS_MON,
 					 AXP20X_VBUS_MON_VBUS_VALID,
@@ -659,6 +718,9 @@ static int axp20x_usb_power_probe(struct platform_device *pdev)
 
 static const struct of_device_id axp20x_usb_power_match[] = {
 	{
+		.compatible = "x-powers,axp192-usb-power-supply",
+		.data = &axp192_data,
+	}, {
 		.compatible = "x-powers,axp202-usb-power-supply",
 		.data = &axp202_data,
 	}, {
-- 
2.35.1

Re: [PATCH v4 11/15] power: supply: axp20x_usb_power: Add support for AXP192

[Andy Shevchenko]

On Wed, Jun 29, 2022 at 4:30 PM Aidan MacDonald
<aidanmacdonald.0x0@gmail.com> wrote:
>
> The AXP192's USB power supply is similar to the AXP202 but it has
> different USB current limits and a different offset for the VBUS
> status register.

Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>

> Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
> Reviewed-by: Chen-Yu Tsai <wens@csie.org>
> Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
> ---
>  drivers/power/supply/axp20x_usb_power.c | 84 +++++++++++++++++++++----
>  1 file changed, 73 insertions(+), 11 deletions(-)
>
> diff --git a/drivers/power/supply/axp20x_usb_power.c b/drivers/power/supply/axp20x_usb_power.c
> index a1e6d1d44808..f83e2ed6d507 100644
> --- a/drivers/power/supply/axp20x_usb_power.c
> +++ b/drivers/power/supply/axp20x_usb_power.c
> @@ -48,6 +48,9 @@
>  #define AXP813_VBUS_CLIMIT_2000mA      2
>  #define AXP813_VBUS_CLIMIT_2500mA      3
>
> +#define AXP192_VBUS_CLIMIT_EN          BIT(1)
> +#define AXP192_VBUS_CLIMIT_100mA       BIT(0)
> +
>  #define AXP20X_ADC_EN1_VBUS_CURR       BIT(2)
>  #define AXP20X_ADC_EN1_VBUS_VOLT       BIT(3)
>
> @@ -121,6 +124,25 @@ static void axp20x_usb_power_poll_vbus(struct work_struct *work)
>                 mod_delayed_work(system_power_efficient_wq, &power->vbus_detect, DEBOUNCE_TIME);
>  }
>
> +static int axp192_get_current_max(struct axp20x_usb_power *power, int *val)
> +{
> +       unsigned int v;
> +       int ret;
> +
> +       ret = regmap_read(power->regmap, AXP20X_VBUS_IPSOUT_MGMT, &v);
> +       if (ret)
> +               return ret;
> +
> +       if (!(v & AXP192_VBUS_CLIMIT_EN))
> +               *val = -1;
> +       else if (v & AXP192_VBUS_CLIMIT_100mA)
> +               *val = 100000;
> +       else
> +               *val = 500000;
> +
> +       return 0;
> +}
> +
>  static int axp20x_get_current_max(struct axp20x_usb_power *power, int *val)
>  {
>         unsigned int v;
> @@ -179,7 +201,7 @@ static int axp20x_usb_power_get_property(struct power_supply *psy,
>         enum power_supply_property psp, union power_supply_propval *val)
>  {
>         struct axp20x_usb_power *power = power_supply_get_drvdata(psy);
> -       unsigned int input, v;
> +       unsigned int input, v, reg;
>         int ret;
>
>         switch (psp) {
> @@ -215,6 +237,8 @@ static int axp20x_usb_power_get_property(struct power_supply *psy,
>         case POWER_SUPPLY_PROP_CURRENT_MAX:
>                 if (power->axp20x_id == AXP813_ID)
>                         return axp813_get_current_max(power, &val->intval);
> +               else if (power->axp20x_id == AXP192_ID)
> +                       return axp192_get_current_max(power, &val->intval);
>                 return axp20x_get_current_max(power, &val->intval);
>         case POWER_SUPPLY_PROP_CURRENT_NOW:
>                 if (IS_ENABLED(CONFIG_AXP20X_ADC)) {
> @@ -256,16 +280,19 @@ static int axp20x_usb_power_get_property(struct power_supply *psy,
>
>                 val->intval = POWER_SUPPLY_HEALTH_GOOD;
>
> -               if (power->axp20x_id == AXP202_ID) {
> -                       ret = regmap_read(power->regmap,
> -                                         AXP20X_USB_OTG_STATUS, &v);
> -                       if (ret)
> -                               return ret;
> +               if (power->axp20x_id == AXP192_ID)
> +                       reg = AXP192_USB_OTG_STATUS;
> +               else if (power->axp20x_id == AXP202_ID)
> +                       reg = AXP20X_USB_OTG_STATUS;
> +               else
> +                       break; /* Other chips lack the OTG status register */
>
> -                       if (!(v & AXP20X_USB_STATUS_VBUS_VALID))
> -                               val->intval =
> -                                       POWER_SUPPLY_HEALTH_UNSPEC_FAILURE;
> -               }
> +               ret = regmap_read(power->regmap, reg, &v);
> +               if (ret)
> +                       return ret;
> +
> +               if (!(v & AXP20X_USB_STATUS_VBUS_VALID))
> +                       val->intval = POWER_SUPPLY_HEALTH_UNSPEC_FAILURE;
>                 break;
>         case POWER_SUPPLY_PROP_PRESENT:
>                 val->intval = !!(input & AXP20X_PWR_STATUS_VBUS_PRESENT);
> @@ -316,6 +343,28 @@ static int axp20x_usb_power_set_voltage_min(struct axp20x_usb_power *power,
>         return -EINVAL;
>  }
>
> +static int axp192_usb_power_set_current_max(struct axp20x_usb_power *power,
> +                                           int intval)
> +{
> +       const unsigned int mask = AXP192_VBUS_CLIMIT_EN |
> +                                 AXP192_VBUS_CLIMIT_100mA;
> +       unsigned int val;
> +
> +       switch (intval) {
> +       case 100000:
> +               val = AXP192_VBUS_CLIMIT_EN | AXP192_VBUS_CLIMIT_100mA;
> +               break;
> +       case 500000:
> +               val = AXP192_VBUS_CLIMIT_EN;
> +               break;
> +       default:
> +               return -EINVAL;
> +       }
> +
> +       return regmap_update_bits(power->regmap,
> +                                 AXP20X_VBUS_IPSOUT_MGMT, mask, val);
> +}
> +
>  static int axp813_usb_power_set_current_max(struct axp20x_usb_power *power,
>                                             int intval)
>  {
> @@ -383,6 +432,9 @@ static int axp20x_usb_power_set_property(struct power_supply *psy,
>                 if (power->axp20x_id == AXP813_ID)
>                         return axp813_usb_power_set_current_max(power,
>                                                                 val->intval);
> +               else if (power->axp20x_id == AXP192_ID)
> +                       return axp192_usb_power_set_current_max(power,
> +                                                               val->intval);
>                 return axp20x_usb_power_set_current_max(power, val->intval);
>
>         default:
> @@ -468,6 +520,13 @@ struct axp_data {
>         enum axp20x_variants            axp20x_id;
>  };
>
> +static const struct axp_data axp192_data = {
> +       .power_desc     = &axp20x_usb_power_desc,
> +       .irq_names      = axp20x_irq_names,
> +       .num_irq_names  = ARRAY_SIZE(axp20x_irq_names),
> +       .axp20x_id      = AXP192_ID,
> +};
> +
>  static const struct axp_data axp202_data = {
>         .power_desc     = &axp20x_usb_power_desc,
>         .irq_names      = axp20x_irq_names,
> @@ -600,7 +659,7 @@ static int axp20x_usb_power_probe(struct platform_device *pdev)
>         if (ret)
>                 return ret;
>
> -       if (power->axp20x_id == AXP202_ID) {
> +       if (power->axp20x_id == AXP192_ID || power->axp20x_id == AXP202_ID) {
>                 /* Enable vbus valid checking */
>                 ret = regmap_update_bits(power->regmap, AXP20X_VBUS_MON,
>                                          AXP20X_VBUS_MON_VBUS_VALID,
> @@ -659,6 +718,9 @@ static int axp20x_usb_power_probe(struct platform_device *pdev)
>
>  static const struct of_device_id axp20x_usb_power_match[] = {
>         {
> +               .compatible = "x-powers,axp192-usb-power-supply",
> +               .data = &axp192_data,
> +       }, {
>                 .compatible = "x-powers,axp202-usb-power-supply",
>                 .data = &axp202_data,
>         }, {
> --
> 2.35.1
>


-- 
With Best Regards,
Andy Shevchenko

[PATCH v4 12/15] pinctrl: Add AXP192 pin control driver

[Aidan MacDonald]

The AXP192 PMIC's GPIO registers are much different from the GPIO
registers of the AXP20x and AXP813 PMICs supported by the existing
pinctrl-axp209 driver. It makes more sense to add a new driver for
the AXP192, rather than add support in the existing axp20x driver.

The pinctrl-axp192 driver is considerably more flexible in terms of
register layout and should be able to support other X-Powers PMICs.
Interrupts and pull down resistor configuration are supported too.

Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
---
 drivers/pinctrl/Kconfig          |  13 +
 drivers/pinctrl/Makefile         |   1 +
 drivers/pinctrl/pinctrl-axp192.c | 598 +++++++++++++++++++++++++++++++
 3 files changed, 612 insertions(+)
 create mode 100644 drivers/pinctrl/pinctrl-axp192.c

diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig
index f52960d2dfbe..5f2c212dd99b 100644
--- a/drivers/pinctrl/Kconfig
+++ b/drivers/pinctrl/Kconfig
@@ -113,6 +113,19 @@ config PINCTRL_AT91PIO4
 	  Say Y here to enable the at91 pinctrl/gpio driver for Atmel PIO4
 	  controller available on sama5d2 SoC.
 
+config PINCTRL_AXP192
+	tristate "X-Powers AXP192 PMIC pinctrl and GPIO Support"
+	depends on MFD_AXP20X
+	select PINMUX
+	select GENERIC_PINCONF
+	select GPIOLIB
+	help
+	  AXP PMICs provide multiple GPIOs that can be muxed for different
+	  functions. This driver bundles a pinctrl driver to select the function
+	  muxing and a GPIO driver to handle the GPIO when the GPIO function is
+	  selected.
+	  Say Y to enable pinctrl and GPIO support for the AXP192 PMIC.
+
 config PINCTRL_AXP209
 	tristate "X-Powers AXP209 PMIC pinctrl and GPIO Support"
 	depends on MFD_AXP20X
diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile
index e76f5cdc64b0..9d2b6420c5dd 100644
--- a/drivers/pinctrl/Makefile
+++ b/drivers/pinctrl/Makefile
@@ -15,6 +15,7 @@ obj-$(CONFIG_PINCTRL_ARTPEC6)	+= pinctrl-artpec6.o
 obj-$(CONFIG_PINCTRL_AS3722)	+= pinctrl-as3722.o
 obj-$(CONFIG_PINCTRL_AT91)	+= pinctrl-at91.o
 obj-$(CONFIG_PINCTRL_AT91PIO4)	+= pinctrl-at91-pio4.o
+obj-$(CONFIG_PINCTRL_AXP192)	+= pinctrl-axp192.o
 obj-$(CONFIG_PINCTRL_AXP209)	+= pinctrl-axp209.o
 obj-$(CONFIG_PINCTRL_BM1880)	+= pinctrl-bm1880.o
 obj-$(CONFIG_PINCTRL_DA850_PUPD) += pinctrl-da850-pupd.o
diff --git a/drivers/pinctrl/pinctrl-axp192.c b/drivers/pinctrl/pinctrl-axp192.c
new file mode 100644
index 000000000000..ce096920b986
--- /dev/null
+++ b/drivers/pinctrl/pinctrl-axp192.c
@@ -0,0 +1,598 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * AXP192 pinctrl and GPIO driver
+ *
+ * Copyright (C) 2022 Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
+ */
+
+#include <linux/bitops.h>
+#include <linux/device.h>
+#include <linux/gpio/driver.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/limits.h>
+#include <linux/mfd/axp20x.h>
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+#include <linux/pinctrl/pinconf-generic.h>
+#include <linux/pinctrl/pinconf.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/pinmux.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+
+enum {
+	AXP192_FUNC_OUTPUT = 0,
+	AXP192_FUNC_INPUT,
+	AXP192_FUNC_LDO,
+	AXP192_FUNC_PWM,
+	AXP192_FUNC_ADC,
+	AXP192_FUNC_LOW_OUTPUT,
+	AXP192_FUNC_FLOATING,
+	AXP192_FUNC_EXT_CHG_CTL,
+	AXP192_FUNC_LDO_STATUS,
+	AXP192_FUNCS_NB,
+};
+
+/**
+ * struct axp192_pctl_function - describes a function that GPIOs may have
+ *
+ * @name: Function name
+ * @muxvals: Mux values used for selecting this function, one per GPIO.
+ *           The i'th element corresponds to the i'th GPIO and is written
+ *           to the GPIO's control register field to select this function.
+ *           U8_MAX indicates that the pin does not support this function.
+ * @groups: Array of @ngroups groups listing pins supporting this function.
+ * @ngroups: Number of pin groups.
+ */
+struct axp192_pctl_function {
+	const char		*name;
+	/* Mux value written to the control register to select the function (-1 if unsupported) */
+	const u8		*muxvals;
+	const char * const	*groups;
+	unsigned int		ngroups;
+};
+
+/**
+ * struct axp192_pctl_reg_info - describes a register and field
+ *
+ * @reg: Register address.
+ * @mask: Bitmask that defines the field.
+ */
+struct axp192_pctl_reg_info {
+	u8 reg;
+	u8 mask;
+};
+
+/**
+ * struct axp192_pctl_desc - describes a pin control device
+ *
+ * @npins: Number of pins.
+ * @pins: Array of @npins pin descriptors.
+ * @ctrl_regs: Describes the control register and field for selecting
+ *	       pin function for each pin. Pin function mux values are
+ *	       written to this field.
+ * @out_regs: Describes the output state register and bit for setting
+ *	      the output signal level when the pin is configured as a
+ *	      GPIO output for each pin.
+ * @in_regs: Describes the input state register and bit for polling
+ *	     the input signal level when the pin is configured as a GPIO
+ *	     input for each pin.
+ * @pull_down_regs: Describes the register and bit used to enable the
+ *		    pull down resistor for each pin. Use a zero mask if
+ *		    the pin does not support a configurable pull down.
+ *
+ * @nfunctions: Number of selectable pinmux functions.
+ * @functions: Array of @nfunctions function descriptors.
+ */
+struct axp192_pctl_desc {
+	unsigned int				npins;
+	const struct pinctrl_pin_desc		*pins;
+	const struct axp192_pctl_reg_info	*ctrl_regs;
+	const struct axp192_pctl_reg_info	*out_regs;
+	const struct axp192_pctl_reg_info	*in_regs;
+	const struct axp192_pctl_reg_info	*pull_down_regs;
+
+	unsigned int				nfunctions;
+	const struct axp192_pctl_function	*functions;
+};
+
+static const struct pinctrl_pin_desc axp192_pins[] = {
+	PINCTRL_PIN(0, "GPIO0"),
+	PINCTRL_PIN(1, "GPIO1"),
+	PINCTRL_PIN(2, "GPIO2"),
+	PINCTRL_PIN(3, "GPIO3"),
+	PINCTRL_PIN(4, "GPIO4"),
+	PINCTRL_PIN(5, "N_RSTO"),
+};
+
+static const char * const axp192_io_groups[] = { "GPIO0", "GPIO1", "GPIO2",
+						 "GPIO3", "GPIO4", "N_RSTO" };
+static const char * const axp192_ldo_groups[] = { "GPIO0" };
+static const char * const axp192_pwm_groups[] = { "GPIO1", "GPIO2" };
+static const char * const axp192_adc_groups[] = { "GPIO0", "GPIO1", "GPIO2", "GPIO3" };
+static const char * const axp192_extended_io_groups[] = { "GPIO0", "GPIO1", "GPIO2" };
+static const char * const axp192_ext_chg_ctl_groups[] = { "GPIO3", "GPIO4" };
+static const char * const axp192_ldo_status_groups[] = { "N_RSTO" };
+
+static const u8 axp192_output_muxvals[]		= {  0,  0,  0,  1,  1,  2 };
+static const u8 axp192_input_muxvals[]		= {  1,  1,  1,  2,  2,  3 };
+static const u8 axp192_ldo_muxvals[]		= {  2, -1, -1, -1, -1, -1 };
+static const u8 axp192_pwm_muxvals[]		= { -1,  2,  2, -1, -1, -1 };
+static const u8 axp192_adc_muxvals[]		= {  4,  4,  4,  3, -1, -1 };
+static const u8 axp192_low_output_muxvals[]	= {  5,  5,  5, -1, -1, -1 };
+static const u8 axp192_floating_muxvals[]	= {  6,  6,  6, -1, -1, -1 };
+static const u8 axp192_ext_chg_ctl_muxvals[]	= { -1, -1, -1,  0,  0, -1 };
+static const u8 axp192_ldo_status_muxvals[]	= { -1, -1, -1, -1, -1,  0 };
+
+static const struct axp192_pctl_function axp192_functions[AXP192_FUNCS_NB] = {
+	[AXP192_FUNC_OUTPUT] = {
+		.name = "output",
+		.muxvals = axp192_output_muxvals,
+		.groups = axp192_io_groups,
+		.ngroups = ARRAY_SIZE(axp192_io_groups),
+	},
+	[AXP192_FUNC_INPUT] = {
+		.name = "input",
+		.muxvals = axp192_input_muxvals,
+		.groups = axp192_io_groups,
+		.ngroups = ARRAY_SIZE(axp192_io_groups),
+	},
+	[AXP192_FUNC_LDO] = {
+		.name = "ldo",
+		.muxvals = axp192_ldo_muxvals,
+		.groups = axp192_ldo_groups,
+		.ngroups = ARRAY_SIZE(axp192_ldo_groups),
+	},
+	[AXP192_FUNC_PWM] = {
+		.name = "pwm",
+		.muxvals = axp192_pwm_muxvals,
+		.groups = axp192_pwm_groups,
+		.ngroups = ARRAY_SIZE(axp192_pwm_groups),
+	},
+	[AXP192_FUNC_ADC] = {
+		.name = "adc",
+		.muxvals = axp192_adc_muxvals,
+		.groups = axp192_adc_groups,
+		.ngroups = ARRAY_SIZE(axp192_adc_groups),
+	},
+	[AXP192_FUNC_LOW_OUTPUT] = {
+		.name = "low_output",
+		.muxvals = axp192_low_output_muxvals,
+		.groups = axp192_extended_io_groups,
+		.ngroups = ARRAY_SIZE(axp192_extended_io_groups),
+	},
+	[AXP192_FUNC_FLOATING] = {
+		.name = "floating",
+		.muxvals = axp192_floating_muxvals,
+		.groups = axp192_extended_io_groups,
+		.ngroups = ARRAY_SIZE(axp192_extended_io_groups),
+	},
+	[AXP192_FUNC_EXT_CHG_CTL] = {
+		.name = "ext_chg_ctl",
+		.muxvals = axp192_ext_chg_ctl_muxvals,
+		.groups = axp192_ext_chg_ctl_groups,
+		.ngroups = ARRAY_SIZE(axp192_ext_chg_ctl_groups),
+	},
+	[AXP192_FUNC_LDO_STATUS] = {
+		.name = "ldo_status",
+		.muxvals = axp192_ldo_status_muxvals,
+		.groups = axp192_ldo_groups,
+		.ngroups = ARRAY_SIZE(axp192_ldo_status_groups),
+	},
+};
+
+static const struct axp192_pctl_reg_info axp192_pin_ctrl_regs[] = {
+	{ .reg = AXP192_GPIO0_CTRL,   .mask = GENMASK(2, 0) },
+	{ .reg = AXP192_GPIO1_CTRL,   .mask = GENMASK(2, 0) },
+	{ .reg = AXP192_GPIO2_CTRL,   .mask = GENMASK(2, 0) },
+	{ .reg = AXP192_GPIO4_3_CTRL, .mask = GENMASK(1, 0) },
+	{ .reg = AXP192_GPIO4_3_CTRL, .mask = GENMASK(3, 2) },
+	{ .reg = AXP192_N_RSTO_CTRL,  .mask = GENMASK(7, 6) },
+};
+
+static const struct axp192_pctl_reg_info axp192_pin_in_regs[] = {
+	{ .reg = AXP192_GPIO2_0_STATE, .mask = BIT(4) },
+	{ .reg = AXP192_GPIO2_0_STATE, .mask = BIT(5) },
+	{ .reg = AXP192_GPIO2_0_STATE, .mask = BIT(6) },
+	{ .reg = AXP192_GPIO4_3_STATE, .mask = BIT(4) },
+	{ .reg = AXP192_GPIO4_3_STATE, .mask = BIT(5) },
+	{ .reg = AXP192_N_RSTO_CTRL,   .mask = BIT(4) },
+};
+
+static const struct axp192_pctl_reg_info axp192_pin_out_regs[] = {
+	{ .reg = AXP192_GPIO2_0_STATE, .mask = BIT(0) },
+	{ .reg = AXP192_GPIO2_0_STATE, .mask = BIT(1) },
+	{ .reg = AXP192_GPIO2_0_STATE, .mask = BIT(2) },
+	{ .reg = AXP192_GPIO4_3_STATE, .mask = BIT(0) },
+	{ .reg = AXP192_GPIO4_3_STATE, .mask = BIT(1) },
+	{ .reg = AXP192_N_RSTO_CTRL,   .mask = BIT(5) },
+};
+
+static const struct axp192_pctl_reg_info axp192_pull_down_regs[] = {
+	{ .reg = AXP192_GPIO2_0_PULL, .mask = BIT(0) },
+	{ .reg = AXP192_GPIO2_0_PULL, .mask = BIT(1) },
+	{ .reg = AXP192_GPIO2_0_PULL, .mask = BIT(2) },
+	{ .reg = 0, .mask = 0 /* unsupported */ },
+	{ .reg = 0, .mask = 0 /* unsupported */ },
+	{ .reg = 0, .mask = 0 /* unsupported */ },
+};
+
+static const struct axp192_pctl_desc axp192_data = {
+	.npins = ARRAY_SIZE(axp192_pins),
+	.pins = axp192_pins,
+	.ctrl_regs = axp192_pin_ctrl_regs,
+	.out_regs = axp192_pin_out_regs,
+	.in_regs = axp192_pin_in_regs,
+	.pull_down_regs = axp192_pull_down_regs,
+
+	.nfunctions = ARRAY_SIZE(axp192_functions),
+	.functions = axp192_functions,
+};
+
+struct axp192_pctl {
+	struct gpio_chip		chip;
+	struct regmap			*regmap;
+	struct regmap_irq_chip_data	*regmap_irqc;
+	struct pinctrl_dev		*pctl_dev;
+	struct device			*dev;
+	const struct axp192_pctl_desc	*desc;
+	int				*irqs;
+};
+
+static int axp192_gpio_get(struct gpio_chip *chip, unsigned int offset)
+{
+	struct axp192_pctl *pctl = gpiochip_get_data(chip);
+	const struct axp192_pctl_reg_info *reginfo = &pctl->desc->in_regs[offset];
+	unsigned int val;
+	int ret;
+
+	ret = regmap_read(pctl->regmap, reginfo->reg, &val);
+	if (ret)
+		return ret;
+
+	return !!(val & reginfo->mask);
+}
+
+static int axp192_gpio_get_direction(struct gpio_chip *chip, unsigned int offset)
+{
+	struct axp192_pctl *pctl = gpiochip_get_data(chip);
+	const struct axp192_pctl_reg_info *reginfo = &pctl->desc->ctrl_regs[offset];
+	const u8 *input_muxvals = pctl->desc->functions[AXP192_FUNC_INPUT].muxvals;
+	unsigned int val;
+	int ret;
+
+	ret = regmap_read(pctl->regmap, reginfo->reg, &val);
+	if (ret)
+		return ret;
+
+	if ((val & reginfo->mask) == (input_muxvals[offset] << (ffs(reginfo->mask) - 1)))
+		return GPIO_LINE_DIRECTION_IN;
+
+	return GPIO_LINE_DIRECTION_OUT;
+}
+
+static void axp192_gpio_set(struct gpio_chip *chip, unsigned int offset, int value)
+{
+	struct axp192_pctl *pctl = gpiochip_get_data(chip);
+	const struct axp192_pctl_reg_info *reginfo = &pctl->desc->out_regs[offset];
+
+	regmap_update_bits(pctl->regmap, reginfo->reg, reginfo->mask, value ? reginfo->mask : 0);
+}
+
+static int axp192_gpio_direction_input(struct gpio_chip *chip, unsigned int offset)
+{
+	return pinctrl_gpio_direction_input(chip->base + offset);
+}
+
+static int axp192_gpio_direction_output(struct gpio_chip *chip, unsigned int offset, int value)
+{
+	chip->set(chip, offset, value);
+
+	return pinctrl_gpio_direction_output(chip->base + offset);
+}
+
+static int axp192_gpio_to_irq(struct gpio_chip *chip, unsigned int offset)
+{
+	struct axp192_pctl *pctl = gpiochip_get_data(chip);
+
+	/* GPIO IRQs are optional */
+	if (!pctl->irqs[offset])
+		return 0;
+
+	return regmap_irq_get_virq(pctl->regmap_irqc, pctl->irqs[offset]);
+}
+
+static int axp192_pinconf_get_pull_down(struct pinctrl_dev *pctldev, unsigned int pin,
+					bool *state)
+{
+	struct axp192_pctl *pctl = pinctrl_dev_get_drvdata(pctldev);
+	const struct axp192_pctl_reg_info *reginfo = &pctl->desc->pull_down_regs[pin];
+	unsigned int val;
+	int ret;
+
+	if (!reginfo->mask)
+		return -ENOTSUPP;
+
+	ret = regmap_read(pctl->regmap, reginfo->reg, &val);
+	if (ret)
+		return ret;
+
+	*state = !!(val & reginfo->mask);
+	return 0;
+}
+
+static int axp192_pinconf_set_pull_down(struct pinctrl_dev *pctldev, unsigned int pin, int value)
+{
+	struct axp192_pctl *pctl = pinctrl_dev_get_drvdata(pctldev);
+	const struct axp192_pctl_reg_info *reginfo = &pctl->desc->pull_down_regs[pin];
+
+	if (!reginfo->mask)
+		return -ENOTSUPP;
+
+	return regmap_update_bits(pctl->regmap, reginfo->reg, reginfo->mask,
+				  value ? reginfo->mask : 0);
+}
+
+static int axp192_pinconf_get(struct pinctrl_dev *pctldev, unsigned int pin, unsigned long *config)
+{
+	enum pin_config_param param = pinconf_to_config_param(*config);
+	unsigned int arg = 1;
+	bool pull_down;
+	int ret;
+
+	switch (param) {
+	case PIN_CONFIG_BIAS_DISABLE:
+		ret = axp192_pinconf_get_pull_down(pctldev, pin, &pull_down);
+		if (ret)
+			return ret;
+		if (pull_down)
+			return -EINVAL;
+		break;
+
+	case PIN_CONFIG_BIAS_PULL_DOWN:
+		ret = axp192_pinconf_get_pull_down(pctldev, pin, &pull_down);
+		if (ret)
+			return ret;
+		if (!pull_down)
+			return -EINVAL;
+		break;
+
+	default:
+		return -ENOTSUPP;
+	}
+
+	*config = pinconf_to_config_packed(param, arg);
+	return 0;
+}
+
+static int axp192_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin,
+			      unsigned long *configs, unsigned int num_configs)
+{
+	int ret;
+	unsigned int cfg;
+
+	for (cfg = 0; cfg < num_configs; cfg++) {
+		switch (pinconf_to_config_param(configs[cfg])) {
+		case PIN_CONFIG_BIAS_DISABLE:
+			ret = axp192_pinconf_set_pull_down(pctldev, pin, 0);
+			if (ret)
+				return ret;
+			break;
+
+		case PIN_CONFIG_BIAS_PULL_DOWN:
+			ret = axp192_pinconf_set_pull_down(pctldev, pin, 1);
+			if (ret)
+				return ret;
+			break;
+
+		default:
+			return -ENOTSUPP;
+		}
+	}
+
+	return 0;
+}
+
+static const struct pinconf_ops axp192_conf_ops = {
+	.is_generic = true,
+	.pin_config_get = axp192_pinconf_get,
+	.pin_config_set = axp192_pinconf_set,
+	.pin_config_group_get = axp192_pinconf_get,
+	.pin_config_group_set = axp192_pinconf_set,
+};
+
+static int axp192_pmx_set(struct pinctrl_dev *pctldev, unsigned int offset, u8 config)
+{
+	struct axp192_pctl *pctl = pinctrl_dev_get_drvdata(pctldev);
+	const struct axp192_pctl_reg_info *reginfo = &pctl->desc->ctrl_regs[offset];
+	unsigned int regval = config << (ffs(reginfo->mask) - 1);
+
+	return regmap_update_bits(pctl->regmap, reginfo->reg, reginfo->mask, regval);
+}
+
+static int axp192_pmx_func_cnt(struct pinctrl_dev *pctldev)
+{
+	struct axp192_pctl *pctl = pinctrl_dev_get_drvdata(pctldev);
+
+	return pctl->desc->nfunctions;
+}
+
+static const char *axp192_pmx_func_name(struct pinctrl_dev *pctldev, unsigned int selector)
+{
+	struct axp192_pctl *pctl = pinctrl_dev_get_drvdata(pctldev);
+
+	return pctl->desc->functions[selector].name;
+}
+
+static int axp192_pmx_func_groups(struct pinctrl_dev *pctldev, unsigned int selector,
+				  const char * const **groups, unsigned int *num_groups)
+{
+	struct axp192_pctl *pctl = pinctrl_dev_get_drvdata(pctldev);
+
+	*groups = pctl->desc->functions[selector].groups;
+	*num_groups = pctl->desc->functions[selector].ngroups;
+
+	return 0;
+}
+
+static int axp192_pmx_set_mux(struct pinctrl_dev *pctldev,
+			      unsigned int function, unsigned int group)
+{
+	struct axp192_pctl *pctl = pinctrl_dev_get_drvdata(pctldev);
+	const u8 *muxvals = pctl->desc->functions[function].muxvals;
+
+	if (muxvals[group] == U8_MAX)
+		return -EINVAL;
+
+	/*
+	 * Switching to LDO or PWM function will enable LDO/PWM output, so it's
+	 * better to ignore these requests and let the regulator or PWM drivers
+	 * handle muxing to avoid interfering with them.
+	 */
+	if (function == AXP192_FUNC_LDO || function == AXP192_FUNC_PWM)
+		return 0;
+
+	return axp192_pmx_set(pctldev, group, muxvals[group]);
+}
+
+static int axp192_pmx_gpio_set_direction(struct pinctrl_dev *pctldev,
+					 struct pinctrl_gpio_range *range,
+					 unsigned int offset, bool input)
+{
+	struct axp192_pctl *pctl = pinctrl_dev_get_drvdata(pctldev);
+	const u8 *muxvals = input ? pctl->desc->functions[AXP192_FUNC_INPUT].muxvals
+				  : pctl->desc->functions[AXP192_FUNC_OUTPUT].muxvals;
+
+	return axp192_pmx_set(pctldev, offset, muxvals[offset]);
+}
+
+static const struct pinmux_ops axp192_pmx_ops = {
+	.get_functions_count	= axp192_pmx_func_cnt,
+	.get_function_name	= axp192_pmx_func_name,
+	.get_function_groups	= axp192_pmx_func_groups,
+	.set_mux		= axp192_pmx_set_mux,
+	.gpio_set_direction	= axp192_pmx_gpio_set_direction,
+	.strict			= true,
+};
+
+static int axp192_groups_cnt(struct pinctrl_dev *pctldev)
+{
+	struct axp192_pctl *pctl = pinctrl_dev_get_drvdata(pctldev);
+
+	return pctl->desc->npins;
+}
+
+static const char *axp192_group_name(struct pinctrl_dev *pctldev, unsigned int selector)
+{
+	struct axp192_pctl *pctl = pinctrl_dev_get_drvdata(pctldev);
+
+	return pctl->desc->pins[selector].name;
+}
+
+static int axp192_group_pins(struct pinctrl_dev *pctldev, unsigned int selector,
+			     const unsigned int **pins, unsigned int *num_pins)
+{
+	struct axp192_pctl *pctl = pinctrl_dev_get_drvdata(pctldev);
+
+	*pins = &pctl->desc->pins[selector].number;
+	*num_pins = 1;
+
+	return 0;
+}
+
+static const struct pinctrl_ops axp192_pctrl_ops = {
+	.dt_node_to_map		= pinconf_generic_dt_node_to_map_group,
+	.dt_free_map		= pinconf_generic_dt_free_map,
+	.get_groups_count	= axp192_groups_cnt,
+	.get_group_name		= axp192_group_name,
+	.get_group_pins		= axp192_group_pins,
+};
+
+static int axp192_pctl_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct axp20x_dev *axp20x = dev_get_drvdata(dev->parent);
+	struct axp192_pctl *pctl;
+	struct pinctrl_desc *pctrl_desc;
+	int ret, i;
+
+	pctl = devm_kzalloc(dev, sizeof(*pctl), GFP_KERNEL);
+	if (!pctl)
+		return -ENOMEM;
+
+	pctl->desc = device_get_match_data(dev);
+	pctl->regmap = axp20x->regmap;
+	pctl->regmap_irqc = axp20x->regmap_irqc;
+	pctl->dev = dev;
+
+	pctl->chip.base			= -1;
+	pctl->chip.can_sleep		= true;
+	pctl->chip.request		= gpiochip_generic_request;
+	pctl->chip.free			= gpiochip_generic_free;
+	pctl->chip.parent		= dev;
+	pctl->chip.label		= dev_name(dev);
+	pctl->chip.owner		= THIS_MODULE;
+	pctl->chip.get			= axp192_gpio_get;
+	pctl->chip.get_direction	= axp192_gpio_get_direction;
+	pctl->chip.set			= axp192_gpio_set;
+	pctl->chip.direction_input	= axp192_gpio_direction_input;
+	pctl->chip.direction_output	= axp192_gpio_direction_output;
+	pctl->chip.to_irq		= axp192_gpio_to_irq;
+	pctl->chip.ngpio		= pctl->desc->npins;
+
+	pctl->irqs = devm_kcalloc(dev, pctl->desc->npins, sizeof(int), GFP_KERNEL);
+	if (!pctl->irqs)
+		return -ENOMEM;
+
+	for (i = 0; i < pctl->desc->npins; i++) {
+		ret = platform_get_irq_byname_optional(pdev, pctl->desc->pins[i].name);
+		if (ret > 0)
+			pctl->irqs[i] = ret;
+	}
+
+	platform_set_drvdata(pdev, pctl);
+
+	pctrl_desc = devm_kzalloc(dev, sizeof(*pctrl_desc), GFP_KERNEL);
+	if (!pctrl_desc)
+		return -ENOMEM;
+
+	pctrl_desc->name = dev_name(dev);
+	pctrl_desc->owner = THIS_MODULE;
+	pctrl_desc->pins = pctl->desc->pins;
+	pctrl_desc->npins = pctl->desc->npins;
+	pctrl_desc->pctlops = &axp192_pctrl_ops;
+	pctrl_desc->pmxops = &axp192_pmx_ops;
+	pctrl_desc->confops = &axp192_conf_ops;
+
+	pctl->pctl_dev = devm_pinctrl_register(dev, pctrl_desc, pctl);
+	if (IS_ERR(pctl->pctl_dev))
+		dev_err_probe(dev, PTR_ERR(pctl->pctl_dev), "couldn't register pinctrl driver\n");
+
+	ret = devm_gpiochip_add_data(dev, &pctl->chip, pctl);
+	if (ret)
+		dev_err_probe(dev, ret, "Failed to register GPIO chip\n");
+
+	return 0;
+}
+
+static const struct of_device_id axp192_pctl_match[] = {
+	{ .compatible = "x-powers,axp192-gpio", .data = &axp192_data, },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, axp192_pctl_match);
+
+static struct platform_driver axp192_pctl_driver = {
+	.probe		= axp192_pctl_probe,
+	.driver = {
+		.name		= "axp192-gpio",
+		.of_match_table	= axp192_pctl_match,
+	},
+};
+module_platform_driver(axp192_pctl_driver);
+
+MODULE_AUTHOR("Aidan MacDonald <aidanmacdonald.0x0@gmail.com>");
+MODULE_DESCRIPTION("AXP192 PMIC pinctrl and GPIO driver");
+MODULE_LICENSE("GPL");
-- 
2.35.1

Re: [PATCH v4 12/15] pinctrl: Add AXP192 pin control driver

[Andy Shevchenko]

On Wed, Jun 29, 2022 at 4:30 PM Aidan MacDonald
<aidanmacdonald.0x0@gmail.com> wrote:
>
> The AXP192 PMIC's GPIO registers are much different from the GPIO
> registers of the AXP20x and AXP813 PMICs supported by the existing
> pinctrl-axp209 driver. It makes more sense to add a new driver for
> the AXP192, rather than add support in the existing axp20x driver.
>
> The pinctrl-axp192 driver is considerably more flexible in terms of
> register layout and should be able to support other X-Powers PMICs.
> Interrupts and pull down resistor configuration are supported too.

...

> +config PINCTRL_AXP192
> +       tristate "X-Powers AXP192 PMIC pinctrl and GPIO Support"
> +       depends on MFD_AXP20X
> +       select PINMUX
> +       select GENERIC_PINCONF
> +       select GPIOLIB
> +       help
> +         AXP PMICs provide multiple GPIOs that can be muxed for different
> +         functions. This driver bundles a pinctrl driver to select the function
> +         muxing and a GPIO driver to handle the GPIO when the GPIO function is
> +         selected.
> +         Say Y to enable pinctrl and GPIO support for the AXP192 PMIC.

What will be the module name if compiled as a module?

...

> +/**
> + * struct axp192_pctl_function - describes a function that GPIOs may have
> + *
> + * @name: Function name
> + * @muxvals: Mux values used for selecting this function, one per GPIO.
> + *           The i'th element corresponds to the i'th GPIO and is written
> + *           to the GPIO's control register field to select this function.
> + *           U8_MAX indicates that the pin does not support this function.
> + * @groups: Array of @ngroups groups listing pins supporting this function.
> + * @ngroups: Number of pin groups.
> + */
> +struct axp192_pctl_function {
> +       const char              *name;
> +       /* Mux value written to the control register to select the function (-1 if unsupported) */
> +       const u8                *muxvals;
> +       const char * const      *groups;
> +       unsigned int            ngroups;
> +};

Can it be replaced by struct function_desc?
https://elixir.bootlin.com/linux/latest/source/drivers/pinctrl/pinmux.h#L130

...

> +       ret = devm_gpiochip_add_data(dev, &pctl->chip, pctl);
> +       if (ret)
> +               dev_err_probe(dev, ret, "Failed to register GPIO chip\n");

Missed return.

-- 
With Best Regards,
Andy Shevchenko

Re: [PATCH v4 12/15] pinctrl: Add AXP192 pin control driver

[Aidan MacDonald]

Andy Shevchenko <andy.shevchenko@gmail.com> writes:

> On Wed, Jun 29, 2022 at 4:30 PM Aidan MacDonald
> <aidanmacdonald.0x0@gmail.com> wrote:
>>
>> The AXP192 PMIC's GPIO registers are much different from the GPIO
>> registers of the AXP20x and AXP813 PMICs supported by the existing
>> pinctrl-axp209 driver. It makes more sense to add a new driver for
>> the AXP192, rather than add support in the existing axp20x driver.
>>
>> The pinctrl-axp192 driver is considerably more flexible in terms of
>> register layout and should be able to support other X-Powers PMICs.
>> Interrupts and pull down resistor configuration are supported too.
>
> ...
>
>> +config PINCTRL_AXP192
>> +       tristate "X-Powers AXP192 PMIC pinctrl and GPIO Support"
>> +       depends on MFD_AXP20X
>> +       select PINMUX
>> +       select GENERIC_PINCONF
>> +       select GPIOLIB
>> +       help
>> +         AXP PMICs provide multiple GPIOs that can be muxed for different
>> +         functions. This driver bundles a pinctrl driver to select the function
>> +         muxing and a GPIO driver to handle the GPIO when the GPIO function is
>> +         selected.
>> +         Say Y to enable pinctrl and GPIO support for the AXP192 PMIC.
>
> What will be the module name if compiled as a module?
>
> ...
>
>> +/**
>> + * struct axp192_pctl_function - describes a function that GPIOs may have
>> + *
>> + * @name: Function name
>> + * @muxvals: Mux values used for selecting this function, one per GPIO.
>> + *           The i'th element corresponds to the i'th GPIO and is written
>> + *           to the GPIO's control register field to select this function.
>> + *           U8_MAX indicates that the pin does not support this function.
>> + * @groups: Array of @ngroups groups listing pins supporting this function.
>> + * @ngroups: Number of pin groups.
>> + */
>> +struct axp192_pctl_function {
>> +       const char              *name;
>> +       /* Mux value written to the control register to select the function (-1 if unsupported) */
>> +       const u8                *muxvals;
>> +       const char * const      *groups;
>> +       unsigned int            ngroups;
>> +};
>
> Can it be replaced by struct function_desc?
> https://elixir.bootlin.com/linux/latest/source/drivers/pinctrl/pinmux.h#L130

That'd work, but using the generic infrastructure doesn't allow me to
simplify anything -- I can eliminate three trivial functions, but the
generic code is higher overhead (extra allocations, radix trees, ...)
so I'd prefer to stick with the current approach.

>> +       ret = devm_gpiochip_add_data(dev, &pctl->chip, pctl);
>> +       if (ret)
>> +               dev_err_probe(dev, ret, "Failed to register GPIO chip\n");
>
> Missed return.

Thanks for catching this, that was pretty silly of me...

Re: [PATCH v4 12/15] pinctrl: Add AXP192 pin control driver

[Andy Shevchenko]

On Fri, Jul 1, 2022 at 5:36 PM Aidan MacDonald
<aidanmacdonald.0x0@gmail.com> wrote:
> Andy Shevchenko <andy.shevchenko@gmail.com> writes:
> > On Wed, Jun 29, 2022 at 4:30 PM Aidan MacDonald
> > <aidanmacdonald.0x0@gmail.com> wrote:

...

> >> +struct axp192_pctl_function {
> >> +       const char              *name;
> >> +       /* Mux value written to the control register to select the function (-1 if unsupported) */
> >> +       const u8                *muxvals;
> >> +       const char * const      *groups;
> >> +       unsigned int            ngroups;
> >> +};
> >
> > Can it be replaced by struct function_desc?
> > https://elixir.bootlin.com/linux/latest/source/drivers/pinctrl/pinmux.h#L130
>
> That'd work, but using the generic infrastructure doesn't allow me to
> simplify anything -- I can eliminate three trivial functions, but the
> generic code is higher overhead (extra allocations, radix trees, ...)

I really don't see how it gets into extra allocations. Either way you
have a pointer to opaque data or in your current code it's called
muxvals. Other fields seem 1:1 what is in struct function_desc. The
code will be probably the same.

I.o.w. I'm talking of eliminating data type, and not about simplifying
the code by fully switching to generic infrastructure.

> so I'd prefer to stick with the current approach.


-- 
With Best Regards,
Andy Shevchenko

Re: [PATCH v4 12/15] pinctrl: Add AXP192 pin control driver

[Aidan MacDonald]

Andy Shevchenko <andy.shevchenko@gmail.com> writes:

> On Fri, Jul 1, 2022 at 5:36 PM Aidan MacDonald
> <aidanmacdonald.0x0@gmail.com> wrote:
>> Andy Shevchenko <andy.shevchenko@gmail.com> writes:
>> > On Wed, Jun 29, 2022 at 4:30 PM Aidan MacDonald
>> > <aidanmacdonald.0x0@gmail.com> wrote:
>
> ...
>
>> >> +struct axp192_pctl_function {
>> >> +       const char              *name;
>> >> +       /* Mux value written to the control register to select the function (-1 if unsupported) */
>> >> +       const u8                *muxvals;
>> >> +       const char * const      *groups;
>> >> +       unsigned int            ngroups;
>> >> +};
>> >
>> > Can it be replaced by struct function_desc?
>> > https://elixir.bootlin.com/linux/latest/source/drivers/pinctrl/pinmux.h#L130
>>
>> That'd work, but using the generic infrastructure doesn't allow me to
>> simplify anything -- I can eliminate three trivial functions, but the
>> generic code is higher overhead (extra allocations, radix trees, ...)
>
> I really don't see how it gets into extra allocations. Either way you
> have a pointer to opaque data or in your current code it's called
> muxvals. Other fields seem 1:1 what is in struct function_desc. The
> code will be probably the same.
>
> I.o.w. I'm talking of eliminating data type, and not about simplifying
> the code by fully switching to generic infrastructure.

struct function_desc is hidden behind an #ifdef, so I can't use it
without enabling the generic pinmux helpers. It doesn't make a lot
of sense to enable them if they're not going to be used.

More generally, why would I use a type from an API I'm not using just
because it happens to look like a type I defined locally? That would
be misleading. Given that the code is the same either way, a local type
is preferable because it clearly communicates that I'm not using the
generic API, and guarantees that the type isn't referenced elsewhere.

Re: [PATCH v4 12/15] pinctrl: Add AXP192 pin control driver

[Samuel Holland]

On 6/29/22 9:30 AM, Aidan MacDonald wrote:
> The AXP192 PMIC's GPIO registers are much different from the GPIO
> registers of the AXP20x and AXP813 PMICs supported by the existing
> pinctrl-axp209 driver. It makes more sense to add a new driver for
> the AXP192, rather than add support in the existing axp20x driver.
> 
> The pinctrl-axp192 driver is considerably more flexible in terms of
> register layout and should be able to support other X-Powers PMICs.
> Interrupts and pull down resistor configuration are supported too.

I am planning to implement gpio/pinctrl support for AXP152[1], which is
somewhere between AXP20x and AXP192 in terms of GPIO capability.

Which driver should I add it to? How much work would it be to convert AXP20x
variants to the new driver? And if supporting other X-Powers PMICs is the plan,
would it make sense to convert the existing driver in-place to avoid dealing
with Kconfig migrations?

[1]: https://linux-sunxi.org/AXP152

> Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
> ---
>  drivers/pinctrl/Kconfig          |  13 +
>  drivers/pinctrl/Makefile         |   1 +
>  drivers/pinctrl/pinctrl-axp192.c | 598 +++++++++++++++++++++++++++++++
>  3 files changed, 612 insertions(+)
>  create mode 100644 drivers/pinctrl/pinctrl-axp192.c
> [...]
> +static int axp192_pinconf_get(struct pinctrl_dev *pctldev, unsigned int pin, unsigned long *config)
> +{
> +	enum pin_config_param param = pinconf_to_config_param(*config);
> +	unsigned int arg = 1;
> +	bool pull_down;
> +	int ret;
> +
> +	switch (param) {
> +	case PIN_CONFIG_BIAS_DISABLE:
> +		ret = axp192_pinconf_get_pull_down(pctldev, pin, &pull_down);
> +		if (ret)
> +			return ret;
> +		if (pull_down)
> +			return -EINVAL;
> +		break;
> +
> +	case PIN_CONFIG_BIAS_PULL_DOWN:
> +		ret = axp192_pinconf_get_pull_down(pctldev, pin, &pull_down);
> +		if (ret)
> +			return ret;
> +		if (!pull_down)
> +			return -EINVAL;
> +		break;
> +
> +	default:
> +		return -ENOTSUPP;
> +	}
> +
> +	*config = pinconf_to_config_packed(param, arg);
> +	return 0;
> +}
> +
> +static int axp192_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin,
> +			      unsigned long *configs, unsigned int num_configs)
> +{
> +	int ret;
> +	unsigned int cfg;
> +
> +	for (cfg = 0; cfg < num_configs; cfg++) {
> +		switch (pinconf_to_config_param(configs[cfg])) {
> +		case PIN_CONFIG_BIAS_DISABLE:
> +			ret = axp192_pinconf_set_pull_down(pctldev, pin, 0);
> +			if (ret)
> +				return ret;
> +			break;
> +
> +		case PIN_CONFIG_BIAS_PULL_DOWN:
> +			ret = axp192_pinconf_set_pull_down(pctldev, pin, 1);
> +			if (ret)
> +				return ret;
> +			break;
> +
> +		default:
> +			return -ENOTSUPP;

The GPIO outputs are always open-drain. It looks like this needs to handle
PIN_CONFIG_DRIVE_OPEN_DRAIN, or gpiolib will try to emulate it.

And I would suggest returning -EINVAL for PIN_CONFIG_DRIVE_PUSH_PULL, but
gpiolib does not check the return value when setting that.

> +		}
> +	}
> +
> +	return 0;
> +}
> +
> [...]
> +
> +static int axp192_pctl_probe(struct platform_device *pdev)
> +{
> +	struct device *dev = &pdev->dev;
> +	struct axp20x_dev *axp20x = dev_get_drvdata(dev->parent);
> +	struct axp192_pctl *pctl;
> +	struct pinctrl_desc *pctrl_desc;
> +	int ret, i;
> +
> +	pctl = devm_kzalloc(dev, sizeof(*pctl), GFP_KERNEL);
> +	if (!pctl)
> +		return -ENOMEM;
> +
> +	pctl->desc = device_get_match_data(dev);
> +	pctl->regmap = axp20x->regmap;
> +	pctl->regmap_irqc = axp20x->regmap_irqc;
> +	pctl->dev = dev;
> +
> +	pctl->chip.base			= -1;
> +	pctl->chip.can_sleep		= true;
> +	pctl->chip.request		= gpiochip_generic_request;
> +	pctl->chip.free			= gpiochip_generic_free;
> +	pctl->chip.parent		= dev;
> +	pctl->chip.label		= dev_name(dev);
> +	pctl->chip.owner		= THIS_MODULE;
> +	pctl->chip.get			= axp192_gpio_get;
> +	pctl->chip.get_direction	= axp192_gpio_get_direction;
> +	pctl->chip.set			= axp192_gpio_set;
> +	pctl->chip.direction_input	= axp192_gpio_direction_input;
> +	pctl->chip.direction_output	= axp192_gpio_direction_output;
> +	pctl->chip.to_irq		= axp192_gpio_to_irq;
> +	pctl->chip.ngpio		= pctl->desc->npins;
> +
> +	pctl->irqs = devm_kcalloc(dev, pctl->desc->npins, sizeof(int), GFP_KERNEL);
> +	if (!pctl->irqs)
> +		return -ENOMEM;
> +
> +	for (i = 0; i < pctl->desc->npins; i++) {
> +		ret = platform_get_irq_byname_optional(pdev, pctl->desc->pins[i].name);
> +		if (ret > 0)
> +			pctl->irqs[i] = ret;
> +	}
> +
> +	platform_set_drvdata(pdev, pctl);
> +
> +	pctrl_desc = devm_kzalloc(dev, sizeof(*pctrl_desc), GFP_KERNEL);
> +	if (!pctrl_desc)
> +		return -ENOMEM;

This can go inside struct axp192_pctl. It does not need a separate allocation.

Regards,
Samuel

Re: [PATCH v4 12/15] pinctrl: Add AXP192 pin control driver

[Aidan MacDonald]

Samuel Holland <samuel@sholland.org> writes:

> On 6/29/22 9:30 AM, Aidan MacDonald wrote:
>> The AXP192 PMIC's GPIO registers are much different from the GPIO
>> registers of the AXP20x and AXP813 PMICs supported by the existing
>> pinctrl-axp209 driver. It makes more sense to add a new driver for
>> the AXP192, rather than add support in the existing axp20x driver.
>> 
>> The pinctrl-axp192 driver is considerably more flexible in terms of
>> register layout and should be able to support other X-Powers PMICs.
>> Interrupts and pull down resistor configuration are supported too.
>
> I am planning to implement gpio/pinctrl support for AXP152[1], which is
> somewhere between AXP20x and AXP192 in terms of GPIO capability.
>
> Which driver should I add it to? How much work would it be to convert AXP20x
> variants to the new driver? And if supporting other X-Powers PMICs is the plan,
> would it make sense to convert the existing driver in-place to avoid dealing
> with Kconfig migrations?
>
> [1]: https://linux-sunxi.org/AXP152
>

I'd assume variants getting new GPIO support would be better off using
this driver. The existing one supports only AXP209 and AXP803/813, and
it hardcodes far too many details.

I'll let the maintainers decide whether converting the existing driver
is better than dealing with possible future migrations. If conversion
is the way to go then I'll drop this patch and revisit GPIO support at
a later date.

>> Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
>> ---
>>  drivers/pinctrl/Kconfig          |  13 +
>>  drivers/pinctrl/Makefile         |   1 +
>>  drivers/pinctrl/pinctrl-axp192.c | 598 +++++++++++++++++++++++++++++++
>>  3 files changed, 612 insertions(+)
>>  create mode 100644 drivers/pinctrl/pinctrl-axp192.c
>> [...]
>> +static int axp192_pinconf_get(struct pinctrl_dev *pctldev, unsigned int pin, unsigned long *config)
>> +{
>> +	enum pin_config_param param = pinconf_to_config_param(*config);
>> +	unsigned int arg = 1;
>> +	bool pull_down;
>> +	int ret;
>> +
>> +	switch (param) {
>> +	case PIN_CONFIG_BIAS_DISABLE:
>> +		ret = axp192_pinconf_get_pull_down(pctldev, pin, &pull_down);
>> +		if (ret)
>> +			return ret;
>> +		if (pull_down)
>> +			return -EINVAL;
>> +		break;
>> +
>> +	case PIN_CONFIG_BIAS_PULL_DOWN:
>> +		ret = axp192_pinconf_get_pull_down(pctldev, pin, &pull_down);
>> +		if (ret)
>> +			return ret;
>> +		if (!pull_down)
>> +			return -EINVAL;
>> +		break;
>> +
>> +	default:
>> +		return -ENOTSUPP;
>> +	}
>> +
>> +	*config = pinconf_to_config_packed(param, arg);
>> +	return 0;
>> +}
>> +
>> +static int axp192_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin,
>> +			      unsigned long *configs, unsigned int num_configs)
>> +{
>> +	int ret;
>> +	unsigned int cfg;
>> +
>> +	for (cfg = 0; cfg < num_configs; cfg++) {
>> +		switch (pinconf_to_config_param(configs[cfg])) {
>> +		case PIN_CONFIG_BIAS_DISABLE:
>> +			ret = axp192_pinconf_set_pull_down(pctldev, pin, 0);
>> +			if (ret)
>> +				return ret;
>> +			break;
>> +
>> +		case PIN_CONFIG_BIAS_PULL_DOWN:
>> +			ret = axp192_pinconf_set_pull_down(pctldev, pin, 1);
>> +			if (ret)
>> +				return ret;
>> +			break;
>> +
>> +		default:
>> +			return -ENOTSUPP;
>
> The GPIO outputs are always open-drain. It looks like this needs to handle
> PIN_CONFIG_DRIVE_OPEN_DRAIN, or gpiolib will try to emulate it.
>
> And I would suggest returning -EINVAL for PIN_CONFIG_DRIVE_PUSH_PULL, but
> gpiolib does not check the return value when setting that.
>

You're right, thanks for pointing that out... guess I should actually
read the documentation sometimes!

>> +		}
>> +	}
>> +
>> +	return 0;
>> +}
>> +
>> [...]
>> +
>> +static int axp192_pctl_probe(struct platform_device *pdev)
>> +{
>> +	struct device *dev = &pdev->dev;
>> +	struct axp20x_dev *axp20x = dev_get_drvdata(dev->parent);
>> +	struct axp192_pctl *pctl;
>> +	struct pinctrl_desc *pctrl_desc;
>> +	int ret, i;
>> +
>> +	pctl = devm_kzalloc(dev, sizeof(*pctl), GFP_KERNEL);
>> +	if (!pctl)
>> +		return -ENOMEM;
>> +
>> +	pctl->desc = device_get_match_data(dev);
>> +	pctl->regmap = axp20x->regmap;
>> +	pctl->regmap_irqc = axp20x->regmap_irqc;
>> +	pctl->dev = dev;
>> +
>> +	pctl->chip.base			= -1;
>> +	pctl->chip.can_sleep		= true;
>> +	pctl->chip.request		= gpiochip_generic_request;
>> +	pctl->chip.free			= gpiochip_generic_free;
>> +	pctl->chip.parent		= dev;
>> +	pctl->chip.label		= dev_name(dev);
>> +	pctl->chip.owner		= THIS_MODULE;
>> +	pctl->chip.get			= axp192_gpio_get;
>> +	pctl->chip.get_direction	= axp192_gpio_get_direction;
>> +	pctl->chip.set			= axp192_gpio_set;
>> +	pctl->chip.direction_input	= axp192_gpio_direction_input;
>> +	pctl->chip.direction_output	= axp192_gpio_direction_output;
>> +	pctl->chip.to_irq		= axp192_gpio_to_irq;
>> +	pctl->chip.ngpio		= pctl->desc->npins;
>> +
>> +	pctl->irqs = devm_kcalloc(dev, pctl->desc->npins, sizeof(int), GFP_KERNEL);
>> +	if (!pctl->irqs)
>> +		return -ENOMEM;
>> +
>> +	for (i = 0; i < pctl->desc->npins; i++) {
>> +		ret = platform_get_irq_byname_optional(pdev, pctl->desc->pins[i].name);
>> +		if (ret > 0)
>> +			pctl->irqs[i] = ret;
>> +	}
>> +
>> +	platform_set_drvdata(pdev, pctl);
>> +
>> +	pctrl_desc = devm_kzalloc(dev, sizeof(*pctrl_desc), GFP_KERNEL);
>> +	if (!pctrl_desc)
>> +		return -ENOMEM;
>
> This can go inside struct axp192_pctl. It does not need a separate allocation.
>
> Regards,
> Samuel

[PATCH v4 13/15] power: axp20x_battery: Add constant charge current table

[Aidan MacDonald]

Add a table-based lookup method for constant charge current,
which is necessary when the setting cannot be represented as
a linear range.

This also replaces the hard-coded 300 mA default ccc setting
if the DT-specified value is unsupported; the minimum value
for the device is now set exactly instead of relying on the
value being rounded down to a supported value.

Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
---
 drivers/power/supply/axp20x_battery.c | 59 +++++++++++++++++++++------
 1 file changed, 47 insertions(+), 12 deletions(-)

diff --git a/drivers/power/supply/axp20x_battery.c b/drivers/power/supply/axp20x_battery.c
index 9106077c0dbb..401779d84d2b 100644
--- a/drivers/power/supply/axp20x_battery.c
+++ b/drivers/power/supply/axp20x_battery.c
@@ -61,6 +61,14 @@ struct axp20x_batt_ps;
 struct axp_data {
 	int	ccc_scale;
 	int	ccc_offset;
+	/*
+	 * Lookup table for constant charge current, if provided this is used
+	 * instead of ccc_scale/ccc_offset.
+	 *
+	 * The table is indexed by the field AXP20X_CHRG_CTRL1_TGT_CURR so it
+	 * must have AXP20X_CHRG_CTRL1_TGT_CURR+1 elements.
+	 */
+	const int *ccc_table;
 	bool	has_fg_valid;
 	int	(*get_max_voltage)(struct axp20x_batt_ps *batt, int *val);
 	int	(*set_max_voltage)(struct axp20x_batt_ps *batt, int val);
@@ -176,7 +184,10 @@ static int axp20x_get_constant_charge_current(struct axp20x_batt_ps *axp,
 
 	*val &= AXP20X_CHRG_CTRL1_TGT_CURR;
 
-	*val = *val * axp->data->ccc_scale + axp->data->ccc_offset;
+	if (axp->data->ccc_table)
+		*val = axp->data->ccc_table[*val];
+	else
+		*val = *val * axp->data->ccc_scale + axp->data->ccc_offset;
 
 	return 0;
 }
@@ -389,16 +400,35 @@ static int axp20x_battery_set_max_voltage(struct axp20x_batt_ps *axp20x_batt,
 				  AXP20X_CHRG_CTRL1_TGT_VOLT, val);
 }
 
+static int axp20x_get_constant_charge_current_sel(struct axp20x_batt_ps *axp_batt,
+						  int charge_current)
+{
+	int i;
+
+	if (axp_batt->data->ccc_table) {
+		for (i = AXP20X_CHRG_CTRL1_TGT_CURR; i >= 0; i--) {
+			if (axp_batt->data->ccc_table[i] <= charge_current)
+				return i;
+		}
+
+		return -EINVAL;
+	}
+
+	i = (charge_current - axp_batt->data->ccc_offset) / axp_batt->data->ccc_scale;
+	if (i > AXP20X_CHRG_CTRL1_TGT_CURR || i < 0)
+		return -EINVAL;
+
+	return i;
+}
+
 static int axp20x_set_constant_charge_current(struct axp20x_batt_ps *axp_batt,
 					      int charge_current)
 {
 	if (charge_current > axp_batt->max_ccc)
 		return -EINVAL;
 
-	charge_current = (charge_current - axp_batt->data->ccc_offset) /
-		axp_batt->data->ccc_scale;
-
-	if (charge_current > AXP20X_CHRG_CTRL1_TGT_CURR || charge_current < 0)
+	charge_current = axp20x_get_constant_charge_current_sel(axp_batt, charge_current);
+	if (charge_current < 0)
 		return -EINVAL;
 
 	return regmap_update_bits(axp_batt->regmap, AXP20X_CHRG_CTRL1,
@@ -410,14 +440,14 @@ static int axp20x_set_max_constant_charge_current(struct axp20x_batt_ps *axp,
 {
 	bool lower_max = false;
 
-	charge_current = (charge_current - axp->data->ccc_offset) /
-		axp->data->ccc_scale;
-
-	if (charge_current > AXP20X_CHRG_CTRL1_TGT_CURR || charge_current < 0)
+	charge_current = axp20x_get_constant_charge_current_sel(axp, charge_current);
+	if (charge_current < 0)
 		return -EINVAL;
 
-	charge_current = charge_current * axp->data->ccc_scale +
-		axp->data->ccc_offset;
+	if (axp->data->ccc_table)
+		charge_current = axp->data->ccc_table[charge_current];
+	else
+		charge_current = charge_current * axp->data->ccc_scale + axp->data->ccc_offset;
 
 	if (charge_current > axp->max_ccc)
 		dev_warn(axp->dev,
@@ -629,7 +659,12 @@ static int axp20x_power_probe(struct platform_device *pdev)
 								   ccc)) {
 			dev_err(&pdev->dev,
 				"couldn't set constant charge current from DT: fallback to minimum value\n");
-			ccc = 300000;
+
+			if (axp20x_batt->data->ccc_table)
+				ccc = axp20x_batt->data->ccc_table[0];
+			else
+				ccc = axp20x_batt->data->ccc_offset;
+
 			axp20x_batt->max_ccc = ccc;
 			axp20x_set_constant_charge_current(axp20x_batt, ccc);
 		}
-- 
2.35.1

Re: [PATCH v4 13/15] power: axp20x_battery: Add constant charge current table

[Andy Shevchenko]

On Wed, Jun 29, 2022 at 4:30 PM Aidan MacDonald
<aidanmacdonald.0x0@gmail.com> wrote:
>
> Add a table-based lookup method for constant charge current,
> which is necessary when the setting cannot be represented as
> a linear range.
>
> This also replaces the hard-coded 300 mA default ccc setting
> if the DT-specified value is unsupported; the minimum value
> for the device is now set exactly instead of relying on the
> value being rounded down to a supported value.

Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>

> Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
> ---
>  drivers/power/supply/axp20x_battery.c | 59 +++++++++++++++++++++------
>  1 file changed, 47 insertions(+), 12 deletions(-)
>
> diff --git a/drivers/power/supply/axp20x_battery.c b/drivers/power/supply/axp20x_battery.c
> index 9106077c0dbb..401779d84d2b 100644
> --- a/drivers/power/supply/axp20x_battery.c
> +++ b/drivers/power/supply/axp20x_battery.c
> @@ -61,6 +61,14 @@ struct axp20x_batt_ps;
>  struct axp_data {
>         int     ccc_scale;
>         int     ccc_offset;
> +       /*
> +        * Lookup table for constant charge current, if provided this is used
> +        * instead of ccc_scale/ccc_offset.
> +        *
> +        * The table is indexed by the field AXP20X_CHRG_CTRL1_TGT_CURR so it
> +        * must have AXP20X_CHRG_CTRL1_TGT_CURR+1 elements.
> +        */
> +       const int *ccc_table;
>         bool    has_fg_valid;
>         int     (*get_max_voltage)(struct axp20x_batt_ps *batt, int *val);
>         int     (*set_max_voltage)(struct axp20x_batt_ps *batt, int val);
> @@ -176,7 +184,10 @@ static int axp20x_get_constant_charge_current(struct axp20x_batt_ps *axp,
>
>         *val &= AXP20X_CHRG_CTRL1_TGT_CURR;
>
> -       *val = *val * axp->data->ccc_scale + axp->data->ccc_offset;
> +       if (axp->data->ccc_table)
> +               *val = axp->data->ccc_table[*val];
> +       else
> +               *val = *val * axp->data->ccc_scale + axp->data->ccc_offset;
>
>         return 0;
>  }
> @@ -389,16 +400,35 @@ static int axp20x_battery_set_max_voltage(struct axp20x_batt_ps *axp20x_batt,
>                                   AXP20X_CHRG_CTRL1_TGT_VOLT, val);
>  }
>
> +static int axp20x_get_constant_charge_current_sel(struct axp20x_batt_ps *axp_batt,
> +                                                 int charge_current)
> +{
> +       int i;
> +
> +       if (axp_batt->data->ccc_table) {
> +               for (i = AXP20X_CHRG_CTRL1_TGT_CURR; i >= 0; i--) {
> +                       if (axp_batt->data->ccc_table[i] <= charge_current)
> +                               return i;
> +               }
> +
> +               return -EINVAL;
> +       }
> +
> +       i = (charge_current - axp_batt->data->ccc_offset) / axp_batt->data->ccc_scale;
> +       if (i > AXP20X_CHRG_CTRL1_TGT_CURR || i < 0)
> +               return -EINVAL;
> +
> +       return i;
> +}
> +
>  static int axp20x_set_constant_charge_current(struct axp20x_batt_ps *axp_batt,
>                                               int charge_current)
>  {
>         if (charge_current > axp_batt->max_ccc)
>                 return -EINVAL;
>
> -       charge_current = (charge_current - axp_batt->data->ccc_offset) /
> -               axp_batt->data->ccc_scale;
> -
> -       if (charge_current > AXP20X_CHRG_CTRL1_TGT_CURR || charge_current < 0)
> +       charge_current = axp20x_get_constant_charge_current_sel(axp_batt, charge_current);
> +       if (charge_current < 0)
>                 return -EINVAL;
>
>         return regmap_update_bits(axp_batt->regmap, AXP20X_CHRG_CTRL1,
> @@ -410,14 +440,14 @@ static int axp20x_set_max_constant_charge_current(struct axp20x_batt_ps *axp,
>  {
>         bool lower_max = false;
>
> -       charge_current = (charge_current - axp->data->ccc_offset) /
> -               axp->data->ccc_scale;
> -
> -       if (charge_current > AXP20X_CHRG_CTRL1_TGT_CURR || charge_current < 0)
> +       charge_current = axp20x_get_constant_charge_current_sel(axp, charge_current);
> +       if (charge_current < 0)
>                 return -EINVAL;
>
> -       charge_current = charge_current * axp->data->ccc_scale +
> -               axp->data->ccc_offset;
> +       if (axp->data->ccc_table)
> +               charge_current = axp->data->ccc_table[charge_current];
> +       else
> +               charge_current = charge_current * axp->data->ccc_scale + axp->data->ccc_offset;
>
>         if (charge_current > axp->max_ccc)
>                 dev_warn(axp->dev,
> @@ -629,7 +659,12 @@ static int axp20x_power_probe(struct platform_device *pdev)
>                                                                    ccc)) {
>                         dev_err(&pdev->dev,
>                                 "couldn't set constant charge current from DT: fallback to minimum value\n");
> -                       ccc = 300000;
> +
> +                       if (axp20x_batt->data->ccc_table)
> +                               ccc = axp20x_batt->data->ccc_table[0];
> +                       else
> +                               ccc = axp20x_batt->data->ccc_offset;
> +
>                         axp20x_batt->max_ccc = ccc;
>                         axp20x_set_constant_charge_current(axp20x_batt, ccc);
>                 }
> --
> 2.35.1
>


-- 
With Best Regards,
Andy Shevchenko

[PATCH v4 14/15] power: axp20x_battery: Support battery status without fuel gauge

[Aidan MacDonald]

Add a "has_fg" flag to indicate that the chip has a fuel gauge.
Report battery full status on chips with no fuel gauge using the
battery voltage.

Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
---
 drivers/power/supply/axp20x_battery.c | 34 ++++++++++++++++++++++++++-
 1 file changed, 33 insertions(+), 1 deletion(-)

diff --git a/drivers/power/supply/axp20x_battery.c b/drivers/power/supply/axp20x_battery.c
index 401779d84d2b..574c1d001556 100644
--- a/drivers/power/supply/axp20x_battery.c
+++ b/drivers/power/supply/axp20x_battery.c
@@ -69,6 +69,7 @@ struct axp_data {
 	 * must have AXP20X_CHRG_CTRL1_TGT_CURR+1 elements.
 	 */
 	const int *ccc_table;
+	bool	has_fg;
 	bool	has_fg_valid;
 	int	(*get_max_voltage)(struct axp20x_batt_ps *batt, int *val);
 	int	(*set_max_voltage)(struct axp20x_batt_ps *batt, int val);
@@ -197,7 +198,7 @@ static int axp20x_battery_get_prop(struct power_supply *psy,
 				   union power_supply_propval *val)
 {
 	struct axp20x_batt_ps *axp20x_batt = power_supply_get_drvdata(psy);
-	int ret = 0, reg, val1;
+	int ret = 0, reg, val1, val2;
 
 	switch (psp) {
 	case POWER_SUPPLY_PROP_PRESENT:
@@ -231,6 +232,34 @@ static int axp20x_battery_get_prop(struct power_supply *psy,
 			return 0;
 		}
 
+		/*
+		 * If the chip does not have a fuel gauge, we check battery full status
+		 * using voltage instead.
+		 */
+		if (!axp20x_batt->data->has_fg) {
+			ret = axp20x_batt->data->get_max_voltage(axp20x_batt, &val1);
+			if (ret)
+				return ret;
+
+			ret = iio_read_channel_processed(axp20x_batt->batt_v, &val2);
+			if (ret)
+				return ret;
+
+			/* IIO subsystem reports voltage in mV but we need uV */
+			val2 *= 1000;
+
+			/*
+			 * According to the AXP192 datasheet, charging will restart if
+			 * the battery voltage drops below V_rch = V_tgt - 0.1 V, so we
+			 * report the battery is full if its voltage is at least V_rch.
+			 */
+			if (val2 >= val1 - 100000)
+				val->intval = POWER_SUPPLY_STATUS_FULL;
+			else
+				val->intval = POWER_SUPPLY_STATUS_NOT_CHARGING;
+			break;
+		}
+
 		ret = regmap_read(axp20x_batt->regmap, AXP20X_FG_RES, &val1);
 		if (ret)
 			return ret;
@@ -552,6 +581,7 @@ static const struct power_supply_desc axp20x_batt_ps_desc = {
 static const struct axp_data axp209_data = {
 	.ccc_scale = 100000,
 	.ccc_offset = 300000,
+	.has_fg = true,
 	.get_max_voltage = axp20x_battery_get_max_voltage,
 	.set_max_voltage = axp20x_battery_set_max_voltage,
 };
@@ -559,6 +589,7 @@ static const struct axp_data axp209_data = {
 static const struct axp_data axp221_data = {
 	.ccc_scale = 150000,
 	.ccc_offset = 300000,
+	.has_fg = true,
 	.has_fg_valid = true,
 	.get_max_voltage = axp22x_battery_get_max_voltage,
 	.set_max_voltage = axp22x_battery_set_max_voltage,
@@ -567,6 +598,7 @@ static const struct axp_data axp221_data = {
 static const struct axp_data axp813_data = {
 	.ccc_scale = 200000,
 	.ccc_offset = 200000,
+	.has_fg = true,
 	.has_fg_valid = true,
 	.get_max_voltage = axp813_battery_get_max_voltage,
 	.set_max_voltage = axp20x_battery_set_max_voltage,
-- 
2.35.1

Re: [PATCH v4 14/15] power: axp20x_battery: Support battery status without fuel gauge

[Andy Shevchenko]

On Wed, Jun 29, 2022 at 4:30 PM Aidan MacDonald
<aidanmacdonald.0x0@gmail.com> wrote:
>
> Add a "has_fg" flag to indicate that the chip has a fuel gauge.
> Report battery full status on chips with no fuel gauge using the
> battery voltage.

Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>

> Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
> Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
> ---
>  drivers/power/supply/axp20x_battery.c | 34 ++++++++++++++++++++++++++-
>  1 file changed, 33 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/power/supply/axp20x_battery.c b/drivers/power/supply/axp20x_battery.c
> index 401779d84d2b..574c1d001556 100644
> --- a/drivers/power/supply/axp20x_battery.c
> +++ b/drivers/power/supply/axp20x_battery.c
> @@ -69,6 +69,7 @@ struct axp_data {
>          * must have AXP20X_CHRG_CTRL1_TGT_CURR+1 elements.
>          */
>         const int *ccc_table;
> +       bool    has_fg;
>         bool    has_fg_valid;
>         int     (*get_max_voltage)(struct axp20x_batt_ps *batt, int *val);
>         int     (*set_max_voltage)(struct axp20x_batt_ps *batt, int val);
> @@ -197,7 +198,7 @@ static int axp20x_battery_get_prop(struct power_supply *psy,
>                                    union power_supply_propval *val)
>  {
>         struct axp20x_batt_ps *axp20x_batt = power_supply_get_drvdata(psy);
> -       int ret = 0, reg, val1;
> +       int ret = 0, reg, val1, val2;
>
>         switch (psp) {
>         case POWER_SUPPLY_PROP_PRESENT:
> @@ -231,6 +232,34 @@ static int axp20x_battery_get_prop(struct power_supply *psy,
>                         return 0;
>                 }
>
> +               /*
> +                * If the chip does not have a fuel gauge, we check battery full status
> +                * using voltage instead.
> +                */
> +               if (!axp20x_batt->data->has_fg) {
> +                       ret = axp20x_batt->data->get_max_voltage(axp20x_batt, &val1);
> +                       if (ret)
> +                               return ret;
> +
> +                       ret = iio_read_channel_processed(axp20x_batt->batt_v, &val2);
> +                       if (ret)
> +                               return ret;
> +
> +                       /* IIO subsystem reports voltage in mV but we need uV */
> +                       val2 *= 1000;
> +
> +                       /*
> +                        * According to the AXP192 datasheet, charging will restart if
> +                        * the battery voltage drops below V_rch = V_tgt - 0.1 V, so we
> +                        * report the battery is full if its voltage is at least V_rch.
> +                        */
> +                       if (val2 >= val1 - 100000)
> +                               val->intval = POWER_SUPPLY_STATUS_FULL;
> +                       else
> +                               val->intval = POWER_SUPPLY_STATUS_NOT_CHARGING;
> +                       break;
> +               }
> +
>                 ret = regmap_read(axp20x_batt->regmap, AXP20X_FG_RES, &val1);
>                 if (ret)
>                         return ret;
> @@ -552,6 +581,7 @@ static const struct power_supply_desc axp20x_batt_ps_desc = {
>  static const struct axp_data axp209_data = {
>         .ccc_scale = 100000,
>         .ccc_offset = 300000,
> +       .has_fg = true,
>         .get_max_voltage = axp20x_battery_get_max_voltage,
>         .set_max_voltage = axp20x_battery_set_max_voltage,
>  };
> @@ -559,6 +589,7 @@ static const struct axp_data axp209_data = {
>  static const struct axp_data axp221_data = {
>         .ccc_scale = 150000,
>         .ccc_offset = 300000,
> +       .has_fg = true,
>         .has_fg_valid = true,
>         .get_max_voltage = axp22x_battery_get_max_voltage,
>         .set_max_voltage = axp22x_battery_set_max_voltage,
> @@ -567,6 +598,7 @@ static const struct axp_data axp221_data = {
>  static const struct axp_data axp813_data = {
>         .ccc_scale = 200000,
>         .ccc_offset = 200000,
> +       .has_fg = true,
>         .has_fg_valid = true,
>         .get_max_voltage = axp813_battery_get_max_voltage,
>         .set_max_voltage = axp20x_battery_set_max_voltage,
> --
> 2.35.1
>


-- 
With Best Regards,
Andy Shevchenko

[PATCH v4 15/15] power: axp20x_battery: Add support for AXP192

[Aidan MacDonald]

The AXP192 has a battery charger similar to other X-Powers PMICs,
but unlike the other supported devices, it does not have a fuel
gauge and can't report battery capacity directly.

Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
---
 drivers/power/supply/axp20x_battery.c | 49 +++++++++++++++++++++++++--
 1 file changed, 46 insertions(+), 3 deletions(-)

diff --git a/drivers/power/supply/axp20x_battery.c b/drivers/power/supply/axp20x_battery.c
index 574c1d001556..1e84d26ce8e3 100644
--- a/drivers/power/supply/axp20x_battery.c
+++ b/drivers/power/supply/axp20x_battery.c
@@ -544,6 +544,19 @@ static int axp20x_battery_set_prop(struct power_supply *psy,
 	}
 }
 
+static enum power_supply_property axp192_battery_props[] = {
+	POWER_SUPPLY_PROP_PRESENT,
+	POWER_SUPPLY_PROP_ONLINE,
+	POWER_SUPPLY_PROP_STATUS,
+	POWER_SUPPLY_PROP_VOLTAGE_NOW,
+	POWER_SUPPLY_PROP_CURRENT_NOW,
+	POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT,
+	POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX,
+	POWER_SUPPLY_PROP_HEALTH,
+	POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN,
+	POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN,
+};
+
 static enum power_supply_property axp20x_battery_props[] = {
 	POWER_SUPPLY_PROP_PRESENT,
 	POWER_SUPPLY_PROP_ONLINE,
@@ -568,6 +581,16 @@ static int axp20x_battery_prop_writeable(struct power_supply *psy,
 	       psp == POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX;
 }
 
+static const struct power_supply_desc axp192_batt_ps_desc = {
+	.name = "axp192-battery",
+	.type = POWER_SUPPLY_TYPE_BATTERY,
+	.properties = axp192_battery_props,
+	.num_properties = ARRAY_SIZE(axp192_battery_props),
+	.property_is_writeable = axp20x_battery_prop_writeable,
+	.get_property = axp20x_battery_get_prop,
+	.set_property = axp20x_battery_set_prop,
+};
+
 static const struct power_supply_desc axp20x_batt_ps_desc = {
 	.name = "axp20x-battery",
 	.type = POWER_SUPPLY_TYPE_BATTERY,
@@ -578,6 +601,19 @@ static const struct power_supply_desc axp20x_batt_ps_desc = {
 	.set_property = axp20x_battery_set_prop,
 };
 
+static const int axp192_ccc_table[AXP20X_CHRG_CTRL1_TGT_CURR+1] = {
+	100000,  190000,  280000,  360000,
+	450000,  550000,  630000,  700000,
+	780000,  880000,  960000,  1000000,
+	1080000, 1160000, 1240000, 1320000,
+};
+
+static const struct axp_data axp192_data = {
+	.ccc_table = axp192_ccc_table,
+	.get_max_voltage = axp20x_battery_get_max_voltage,
+	.set_max_voltage = axp20x_battery_set_max_voltage,
+};
+
 static const struct axp_data axp209_data = {
 	.ccc_scale = 100000,
 	.ccc_offset = 300000,
@@ -606,6 +642,9 @@ static const struct axp_data axp813_data = {
 
 static const struct of_device_id axp20x_battery_ps_id[] = {
 	{
+		.compatible = "x-powers,axp192-battery-power-supply",
+		.data = (void *)&axp192_data,
+	}, {
 		.compatible = "x-powers,axp209-battery-power-supply",
 		.data = (void *)&axp209_data,
 	}, {
@@ -623,6 +662,7 @@ static int axp20x_power_probe(struct platform_device *pdev)
 	struct axp20x_batt_ps *axp20x_batt;
 	struct power_supply_config psy_cfg = {};
 	struct power_supply_battery_info *info;
+	const struct power_supply_desc *ps_desc;
 	struct device *dev = &pdev->dev;
 
 	if (!of_device_is_available(pdev->dev.of_node))
@@ -666,9 +706,12 @@ static int axp20x_power_probe(struct platform_device *pdev)
 
 	axp20x_batt->data = (struct axp_data *)of_device_get_match_data(dev);
 
-	axp20x_batt->batt = devm_power_supply_register(&pdev->dev,
-						       &axp20x_batt_ps_desc,
-						       &psy_cfg);
+	if (!axp20x_batt->data->has_fg)
+		ps_desc = &axp192_batt_ps_desc;
+	else
+		ps_desc = &axp20x_batt_ps_desc;
+
+	axp20x_batt->batt = devm_power_supply_register(&pdev->dev, ps_desc, &psy_cfg);
 	if (IS_ERR(axp20x_batt->batt)) {
 		dev_err(&pdev->dev, "failed to register power supply: %ld\n",
 			PTR_ERR(axp20x_batt->batt));
-- 
2.35.1

Re: [PATCH v4 15/15] power: axp20x_battery: Add support for AXP192

[Andy Shevchenko]

On Wed, Jun 29, 2022 at 4:30 PM Aidan MacDonald
<aidanmacdonald.0x0@gmail.com> wrote:
>
> The AXP192 has a battery charger similar to other X-Powers PMICs,
> but unlike the other supported devices, it does not have a fuel
> gauge and can't report battery capacity directly.

Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>

> Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
> Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
> ---
>  drivers/power/supply/axp20x_battery.c | 49 +++++++++++++++++++++++++--
>  1 file changed, 46 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/power/supply/axp20x_battery.c b/drivers/power/supply/axp20x_battery.c
> index 574c1d001556..1e84d26ce8e3 100644
> --- a/drivers/power/supply/axp20x_battery.c
> +++ b/drivers/power/supply/axp20x_battery.c
> @@ -544,6 +544,19 @@ static int axp20x_battery_set_prop(struct power_supply *psy,
>         }
>  }
>
> +static enum power_supply_property axp192_battery_props[] = {
> +       POWER_SUPPLY_PROP_PRESENT,
> +       POWER_SUPPLY_PROP_ONLINE,
> +       POWER_SUPPLY_PROP_STATUS,
> +       POWER_SUPPLY_PROP_VOLTAGE_NOW,
> +       POWER_SUPPLY_PROP_CURRENT_NOW,
> +       POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT,
> +       POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX,
> +       POWER_SUPPLY_PROP_HEALTH,
> +       POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN,
> +       POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN,
> +};
> +
>  static enum power_supply_property axp20x_battery_props[] = {
>         POWER_SUPPLY_PROP_PRESENT,
>         POWER_SUPPLY_PROP_ONLINE,
> @@ -568,6 +581,16 @@ static int axp20x_battery_prop_writeable(struct power_supply *psy,
>                psp == POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX;
>  }
>
> +static const struct power_supply_desc axp192_batt_ps_desc = {
> +       .name = "axp192-battery",
> +       .type = POWER_SUPPLY_TYPE_BATTERY,
> +       .properties = axp192_battery_props,
> +       .num_properties = ARRAY_SIZE(axp192_battery_props),
> +       .property_is_writeable = axp20x_battery_prop_writeable,
> +       .get_property = axp20x_battery_get_prop,
> +       .set_property = axp20x_battery_set_prop,
> +};
> +
>  static const struct power_supply_desc axp20x_batt_ps_desc = {
>         .name = "axp20x-battery",
>         .type = POWER_SUPPLY_TYPE_BATTERY,
> @@ -578,6 +601,19 @@ static const struct power_supply_desc axp20x_batt_ps_desc = {
>         .set_property = axp20x_battery_set_prop,
>  };
>
> +static const int axp192_ccc_table[AXP20X_CHRG_CTRL1_TGT_CURR+1] = {
> +       100000,  190000,  280000,  360000,
> +       450000,  550000,  630000,  700000,
> +       780000,  880000,  960000,  1000000,
> +       1080000, 1160000, 1240000, 1320000,
> +};
> +
> +static const struct axp_data axp192_data = {
> +       .ccc_table = axp192_ccc_table,
> +       .get_max_voltage = axp20x_battery_get_max_voltage,
> +       .set_max_voltage = axp20x_battery_set_max_voltage,
> +};
> +
>  static const struct axp_data axp209_data = {
>         .ccc_scale = 100000,
>         .ccc_offset = 300000,
> @@ -606,6 +642,9 @@ static const struct axp_data axp813_data = {
>
>  static const struct of_device_id axp20x_battery_ps_id[] = {
>         {
> +               .compatible = "x-powers,axp192-battery-power-supply",
> +               .data = (void *)&axp192_data,
> +       }, {
>                 .compatible = "x-powers,axp209-battery-power-supply",
>                 .data = (void *)&axp209_data,
>         }, {
> @@ -623,6 +662,7 @@ static int axp20x_power_probe(struct platform_device *pdev)
>         struct axp20x_batt_ps *axp20x_batt;
>         struct power_supply_config psy_cfg = {};
>         struct power_supply_battery_info *info;
> +       const struct power_supply_desc *ps_desc;
>         struct device *dev = &pdev->dev;
>
>         if (!of_device_is_available(pdev->dev.of_node))
> @@ -666,9 +706,12 @@ static int axp20x_power_probe(struct platform_device *pdev)
>
>         axp20x_batt->data = (struct axp_data *)of_device_get_match_data(dev);
>
> -       axp20x_batt->batt = devm_power_supply_register(&pdev->dev,
> -                                                      &axp20x_batt_ps_desc,
> -                                                      &psy_cfg);
> +       if (!axp20x_batt->data->has_fg)
> +               ps_desc = &axp192_batt_ps_desc;
> +       else
> +               ps_desc = &axp20x_batt_ps_desc;
> +
> +       axp20x_batt->batt = devm_power_supply_register(&pdev->dev, ps_desc, &psy_cfg);
>         if (IS_ERR(axp20x_batt->batt)) {
>                 dev_err(&pdev->dev, "failed to register power supply: %ld\n",
>                         PTR_ERR(axp20x_batt->batt));
> --
> 2.35.1
>


-- 
With Best Regards,
Andy Shevchenko

Re: [PATCH v4 00/15] Add support for AXP192 PMIC

[Andy Shevchenko]

On Wed, Jun 29, 2022 at 4:29 PM Aidan MacDonald
<aidanmacdonald.0x0@gmail.com> wrote:
>
> Changes in v4:
>
> * Drop regmap-irq patches and rebase on top of the regmap-irq
>   refactoring series[1], which implements the same functionality.
> * Reorder mfd_cells, putting one-line entries at the bottom.
> * Fix incorrect example in axp192-gpio device tree bindings.
> * Perform adc_en2 flag -> adc_en2_mask conversion in axp20x_adc
>   as a separate patch.
> * Simplify axp192_usb_power_set_current_max().
> * Drop unneeded OF dependency in pin control driver, and document
>   tables used for describing register layouts.
> * Various style fixups suggested by Andy Shevchenko.


For patches 6-11
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>

> [1]: https://lore.kernel.org/lkml/20220623211420.918875-1-aidanmacdonald.0x0@gmail.com/
>
> Changes in v3:
>
> * Update pinctrl driver to address Andy Shevchenko's review comments
>   from v1, and fix a few other issues.
> * Add gpio-ranges property and example snippet to gpio DT bindings.
> * Update commit message of patch 01/16 to point out that all register
>   addresses are obtained using sub_irq_reg().
> * Document ccc_table in axp20x_battery. Also update commit message to
>   note a small fix that is part of that patch.
> * Drop axp20x_adc consolidation patch in favor of using separate adc_raw
>   functions. It's a minor code size optimization that may not be worth
>   the effort due to implementation complexity.
> * Use the FIELD_GET macro in axp20x_adc to further clarify intent.
> * Fix a typo in the regulator driver where an AXP20X regulator ID was
>   mistakenly used instead of an AXP192 regulator ID. Also carry over
>   an Acked-by: tag from v1. Hope that's okay.
> * Accumulate Acked-by: tags from v1 on DT patches.
> * Accumulate Acked-by: tags from v2.
>
> Note that regmap maintainer Mark Brown has said the first two patches to
> regmap-irq aren't suitable for inclusion into the kernel in their current
> state. I'm including them for v3 so the series remains testable.
>
> Changes in v2:
>
> * Do a little cleanup of axp20x_adc suggested by Jonathan Cameron
> * Consolidate ADC read functions in axp20x_adc
> * Drop the axp192's read_label callback in axp20x_adc
> * Clean up the axp192-gpio dt bindings
> * Rewrite a problematic bit of code in axp20x_usb_power reported
>   by kernel test robot
> * Support AXP192 in axp20x_battery
> * Split up regmap-irq changes to two separate patches
>
> Cover letter from v1:
>
> Hi all,
>
> This patch series adds support for the X-Powers AXP192 PMIC to the
> AXP20x driver framework.
>
> The first patch is a small change to regmap-irq to support the AXP192's
> unusual IRQ register layout. It isn't possible to include all of the
> IRQ registers in one regmap-irq chip without this.
>
> The rest of the changes are pretty straightforward, I think the only
> notable parts are the axp20x_adc driver where there seems to be some
> opportunities for code reuse (the axp192 is nearly a duplicate of the
> axp20x) and the addition of a new pinctrl driver for the axp192, since
> the axp20x pinctrl driver was not very easy to adapt.
>
> Aidan MacDonald (15):
>   dt-bindings: mfd: add bindings for AXP192 MFD device
>   dt-bindings: iio: adc: axp209: Add AXP192 compatible
>   dt-bindings: power: supply: axp20x: Add AXP192 compatible
>   dt-bindings: gpio: Add AXP192 GPIO bindings
>   dt-bindings: power: axp20x-battery: Add AXP192 compatible
>   mfd: axp20x: Add support for AXP192
>   regulator: axp20x: Add support for AXP192
>   iio: adc: axp20x_adc: Minor code cleanups
>   iio: adc: axp20x_adc: Replace adc_en2 flag with adc_en2_mask field
>   iio: adc: axp20x_adc: Add support for AXP192
>   power: supply: axp20x_usb_power: Add support for AXP192
>   pinctrl: Add AXP192 pin control driver
>   power: axp20x_battery: Add constant charge current table
>   power: axp20x_battery: Support battery status without fuel gauge
>   power: axp20x_battery: Add support for AXP192
>
>  .../bindings/gpio/x-powers,axp192-gpio.yaml   |  68 ++
>  .../bindings/iio/adc/x-powers,axp209-adc.yaml |  18 +
>  .../bindings/mfd/x-powers,axp152.yaml         |   1 +
>  .../x-powers,axp20x-battery-power-supply.yaml |   1 +
>  .../x-powers,axp20x-usb-power-supply.yaml     |   1 +
>  drivers/iio/adc/axp20x_adc.c                  | 356 +++++++++--
>  drivers/mfd/axp20x-i2c.c                      |   2 +
>  drivers/mfd/axp20x.c                          | 152 +++++
>  drivers/pinctrl/Kconfig                       |  13 +
>  drivers/pinctrl/Makefile                      |   1 +
>  drivers/pinctrl/pinctrl-axp192.c              | 598 ++++++++++++++++++
>  drivers/power/supply/axp20x_battery.c         | 142 ++++-
>  drivers/power/supply/axp20x_usb_power.c       |  84 ++-
>  drivers/regulator/axp20x-regulator.c          | 100 ++-
>  include/linux/mfd/axp20x.h                    |  84 +++
>  15 files changed, 1547 insertions(+), 74 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/gpio/x-powers,axp192-gpio.yaml
>  create mode 100644 drivers/pinctrl/pinctrl-axp192.c
>
> --
> 2.35.1
>


-- 
With Best Regards,
Andy Shevchenko

Re: [PATCH v4 00/15] Add support for AXP192 PMIC

[Andy Shevchenko]

On Wed, Jun 29, 2022 at 11:14 PM Andy Shevchenko
<andy.shevchenko@gmail.com> wrote:
> On Wed, Jun 29, 2022 at 4:29 PM Aidan MacDonald
> <aidanmacdonald.0x0@gmail.com> wrote:
> >
> > Changes in v4:
> >
> > * Drop regmap-irq patches and rebase on top of the regmap-irq
> >   refactoring series[1], which implements the same functionality.
> > * Reorder mfd_cells, putting one-line entries at the bottom.
> > * Fix incorrect example in axp192-gpio device tree bindings.
> > * Perform adc_en2 flag -> adc_en2_mask conversion in axp20x_adc
> >   as a separate patch.
> > * Simplify axp192_usb_power_set_current_max().
> > * Drop unneeded OF dependency in pin control driver, and document
> >   tables used for describing register layouts.
> > * Various style fixups suggested by Andy Shevchenko.
>
>
> For patches 6-11
> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>

Ditto for patches 13-15.

Very good made series, thanks!

> > This patch series adds support for the X-Powers AXP192 PMIC to the
> > AXP20x driver framework.
> >
> > The first patch is a small change to regmap-irq to support the AXP192's
> > unusual IRQ register layout. It isn't possible to include all of the
> > IRQ registers in one regmap-irq chip without this.
> >
> > The rest of the changes are pretty straightforward, I think the only
> > notable parts are the axp20x_adc driver where there seems to be some
> > opportunities for code reuse (the axp192 is nearly a duplicate of the
> > axp20x) and the addition of a new pinctrl driver for the axp192, since
> > the axp20x pinctrl driver was not very easy to adapt.

-- 
With Best Regards,
Andy Shevchenko

Re: [PATCH v4 00/15] Add support for AXP192 PMIC

[Lee Jones]

On Wed, 29 Jun 2022, Andy Shevchenko wrote:

> On Wed, Jun 29, 2022 at 11:14 PM Andy Shevchenko
> <andy.shevchenko@gmail.com> wrote:
> > On Wed, Jun 29, 2022 at 4:29 PM Aidan MacDonald
> > <aidanmacdonald.0x0@gmail.com> wrote:
> > >
> > > Changes in v4:
> > >
> > > * Drop regmap-irq patches and rebase on top of the regmap-irq
> > >   refactoring series[1], which implements the same functionality.
> > > * Reorder mfd_cells, putting one-line entries at the bottom.
> > > * Fix incorrect example in axp192-gpio device tree bindings.
> > > * Perform adc_en2 flag -> adc_en2_mask conversion in axp20x_adc
> > >   as a separate patch.
> > > * Simplify axp192_usb_power_set_current_max().
> > > * Drop unneeded OF dependency in pin control driver, and document
> > >   tables used for describing register layouts.
> > > * Various style fixups suggested by Andy Shevchenko.
> >
> >
> > For patches 6-11
> > Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
> 
> Ditto for patches 13-15.

Not sure `b4` will pick these up!

-- 
Lee Jones [李琼斯]
Principal Technical Lead - Developer Services
Linaro.org │ Open source software for Arm SoCs
Follow Linaro: Facebook | Twitter | Blog

Re: [PATCH v4 00/15] Add support for AXP192 PMIC

[Andy Shevchenko]

On Thu, Jun 30, 2022 at 9:55 AM Lee Jones <lee.jones@linaro.org> wrote:
> On Wed, 29 Jun 2022, Andy Shevchenko wrote:
> > On Wed, Jun 29, 2022 at 11:14 PM Andy Shevchenko
> > <andy.shevchenko@gmail.com> wrote:
> > > On Wed, Jun 29, 2022 at 4:29 PM Aidan MacDonald
> > > <aidanmacdonald.0x0@gmail.com> wrote:
> > > >
> > > > Changes in v4:
> > > >
> > > > * Drop regmap-irq patches and rebase on top of the regmap-irq
> > > >   refactoring series[1], which implements the same functionality.
> > > > * Reorder mfd_cells, putting one-line entries at the bottom.
> > > > * Fix incorrect example in axp192-gpio device tree bindings.
> > > > * Perform adc_en2 flag -> adc_en2_mask conversion in axp20x_adc
> > > >   as a separate patch.
> > > > * Simplify axp192_usb_power_set_current_max().
> > > > * Drop unneeded OF dependency in pin control driver, and document
> > > >   tables used for describing register layouts.
> > > > * Various style fixups suggested by Andy Shevchenko.
> > >
> > > For patches 6-11
> > > Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
> >
> > Ditto for patches 13-15.
>
> Not sure `b4` will pick these up!

No it won't. But it's not an issue, one may use `git msg-filter` for
that, esp. taking into account that series most likely will be resent
due to patch 12 (`but not fully sure it will be the case).

For your convenience I have added on per patch basis.

-- 
With Best Regards,
Andy Shevchenko

Re: [PATCH v4 00/15] Add support for AXP192 PMIC

[Lee Jones]

On Thu, 30 Jun 2022, Andy Shevchenko wrote:

> On Thu, Jun 30, 2022 at 9:55 AM Lee Jones <lee.jones@linaro.org> wrote:
> > On Wed, 29 Jun 2022, Andy Shevchenko wrote:
> > > On Wed, Jun 29, 2022 at 11:14 PM Andy Shevchenko
> > > <andy.shevchenko@gmail.com> wrote:
> > > > On Wed, Jun 29, 2022 at 4:29 PM Aidan MacDonald
> > > > <aidanmacdonald.0x0@gmail.com> wrote:
> > > > >
> > > > > Changes in v4:
> > > > >
> > > > > * Drop regmap-irq patches and rebase on top of the regmap-irq
> > > > >   refactoring series[1], which implements the same functionality.
> > > > > * Reorder mfd_cells, putting one-line entries at the bottom.
> > > > > * Fix incorrect example in axp192-gpio device tree bindings.
> > > > > * Perform adc_en2 flag -> adc_en2_mask conversion in axp20x_adc
> > > > >   as a separate patch.
> > > > > * Simplify axp192_usb_power_set_current_max().
> > > > > * Drop unneeded OF dependency in pin control driver, and document
> > > > >   tables used for describing register layouts.
> > > > > * Various style fixups suggested by Andy Shevchenko.
> > > >
> > > > For patches 6-11
> > > > Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
> > >
> > > Ditto for patches 13-15.
> >
> > Not sure `b4` will pick these up!
> 
> No it won't. But it's not an issue, one may use `git msg-filter` for
> that, esp. taking into account that series most likely will be resent
> due to patch 12 (`but not fully sure it will be the case).
> 
> For your convenience I have added on per patch basis.

That helps, thanks Andy.

-- 
Lee Jones [李琼斯]
Principal Technical Lead - Developer Services
Linaro.org │ Open source software for Arm SoCs
Follow Linaro: Facebook | Twitter | Blog